Health Care Waste Management Manual 3rd Ed

Department of Health
Manila
2012
Manual on
Healthcare Waste
Management
Third Edition
Manual on Healthcare Waste Management
Third Edition
December 2011
The preparation and publication of this document was made possible through
the assistance of the United Nations Development Programme (UNDP) - Global
Environment Facility (GEF) project, Demonstrating and Promoting Best Practices
and Techniques for Reducing Health Care Waste to Avoid Environmental Releases of
Dioxin and Mercury and the World Health Organization.
This document is published by the Department of Health- National Center for Health
Facility Development (NCHFD), Bldg. 4, Department of Health, Tayuman St. cor.
Rizal Avenue, Sta. Cruz, Manila, 1003 Philippines, for general distribution. All rights
reserved. Subject to the acknowledgement of DOH-NCHFD, the Manual may be freely
abstracted, reproduced or translated in part or in whole for non-commercial purposes
only. If the entire work or substantial portions will be translated or reproduced,
permission should be requested from the DOH-NCHFD.
Republic of the Philippines
OFFICE OF THE SECRETARY
MESSAGE
Access to affordable, quality and responsive healthcare services and facilities is

the primary concern of all healthcare facilities and is one of the key strategic thrusts
of the Aquino Administration Health Agenda: Achieving Universal Health Care
for All Filipinos or Kalusugang Pangkalahatan, in order to ensure better health
for our countrymen. The Department of Health launched numerous initiatives to
implement this commitment, among which are our increased efforts towards patient
safety, Malinis at Mabangong Ospital, Health Facility Enhancement Program and
PhilHealths Benchbook on performance improvement of health services. Proper
management of healthcare waste is a common thread in these efforts to attain high
standards for provision of healthcare services.
The revision of the 2004 2nd Edition Manual on Healthcare Waste Management
is intended to make our guidelines, practices and techniques compliant with policies
and legislations enacted in the last seven years and be at par with international best
practices. A national roadmap that defines our medium-term strategic directions and a
training module to keep health workers informed are two other complementary efforts
of the Department to enhance national capacities in managing healthcare waste.
Now, the challenge of each and every healthcare facility is to minimize,

properly segregate, treat and dispose of the wastes it generates. As we worked
together in completing this 3rd edition Manual on Healthcare Waste Management, let
us continue our cooperation to prevent the spread of disease, occurrence of accidents
and degradation of our environment.
ENRIQUE T. ONA, MD. FPCS, FACS

Secretary of Health
MANUAL ON HEALTHCARE WASTE MANAGEMENT, THIRD EDITION
viii
PREFACE
With the issuances of different laws and Administrative Orders and Implementing
Rules and Regulations jointly by the Department of Health and the Department of
Environment and Natural Resources, there is an urgent need to review and update the
2004 2nd Edition Healthcare Waste Management Manual of the DOH. Notwithstanding
the major concerns on the proper handling of waste generated by Healthcare Facilities,
the risks and threats caused by improper handling of wastes on human health and the
environment has been a continuing problem.
These considerations led to the preparation of the 3rd Edition Manual on

Healthcare Waste Management, which is more comprehensive and user-friendly. The
Manual is composed of four (4) main parts, each one subdivided into various chapters. It
includes a General Description of Healthcare Waste Management (HCWM), Components
of HCWM, Administrative Requirements, and copies of related laws and issuances and
sample of forms to be used in the implementation of a Healthcare Waste Management
program in the Healthcare Facility.
While the 3rd edition Manual on HCWM has been designed to serve as guide for
both hospital administrators and staff for application to the current situation, a review and
updating may be essential after five (5) years or so. Any proposal for revision shall be
forwarded to the National Center for Health Facility Development for consideration.
Ensuing amendments to the Manual shall be subject to the formal approval of the
Secretary of Health.
ix
ACKNOWLEDGMENT
The Manual on Healthcare Waste Management, 3rd edition was made possible through
the collaborative effort of government, the private sector and international development
partners. We thank
Our international development partners: Mr. Renaud Meyer, Country Director,

United Nations Development Programme and Dr. Soe Nyunt-U, World Health
Organization Representative to the Philippines
The head of the offices of the members of the Technical Working Group:
Director Juan Miguel Cuna, Environmental Management Bureau, DENR; OIC-
Assistant Secretary Enrique A. Tayag and Dr. Winston Go, Medical Center
Chiefs, San Lazaro Hospital, Manila; Sis. Normita L. Guevara, D.C., Vice
President for Health Services, San Juan De Dios Educational Foundation Inc.
(Hospital), Pasay City; Dr. Ludgerio D. Torres and Dr. Manuel Chua Chiaco,
Executive Directors, Philippine Heart Center, Quezon City; Dr. Edgardo V.
Salud, Chief of Hospital, Quezon City General Hospital, Quezon City; Director
Eduardo C. Janairo, MD and Director Lilibeth C. David, MD, National Center
for Disease Prevention and Control - DOH; Director Juanito Taleon, MD,
Center for Health Development - CALABARZON and Dr. Soe Nyunt-U,
World Health Organization for allowing their staff to actively participate as
members of the TWG that prepared this manual;
The TWG members, HCWM stakeholders and resource persons whose names
appear in the succeeding pages for participating in the meetings and
consultations and for sharing their experience and knowledge; and
San Lazaro Hospital, San Juan De Dios Educational Foundation, Inc (Hospital),
and the University of the Philippines- National Institutes of Health for allowing
us to take photographs of their institutions for use in this Manual.
x
x
TECHNICAL WORKING GROUP
Ms. Eleonorita Reyes

Chair, Technical Working Group
San Lazaro Hospital, Manila
Engr. Aida Calma

Co-Chair
San Lazaro Hospital, Manila/ UNDP-GEF Project, Philippines
Members
Engr. Elmer Benedictos Department of Health- National Center for
Disease Prevention and Control
Ms. Gilda Cirila Ramos San Juan De Dios Educational Foundation,
Inc. (Hospital), Pasay City
Engr. Bonifacio Magtibay World Health Organization-Philippines
Ms. Ester Borja Philippine Heart Center, Quezon City
Engr. Jose Barzaga Philippine Heart Center, Quezon City
Engr. Corazon Vidad Department of Health -Center for Health
Development CALABARZON
Dr. Jose Briones Quezon City General Hospital, Quezon City
Mr. Salvador Passe, Jr. Department of Environment and Natural
Resources -Environment Management Bureau
Ms. Deborah Carmina Sarmiento UNDP-GEF Project, Philippines
Ms. Erika Claudine Tabunar UNDP-GEF Project, Philippines
Advisers
Director Ma. Rebecca Peafiel DOH-National Center for Health Facility
Development
Director Maylene Beltran DOH-Bureau of International Health
Cooperation
Director Asuncion Anden,M.D DOH-National Center for Health Facility
Development
Director Criselda Abesamis,M.D. DOH-National Center for Health Facility
Development/ Office for Special Concerns
Administrative and Secretarial Support

Ms. Levi Lacuarin UNDP-GEF Project, Philippines
Ms. Marcela Hilot UNDP-GEF Project, Philippines
xi
xi
CONTRIBUTORS AND RESOURCE PERSONS
Dr. Mario C. Villaverde Undersecretary of Health

Dr. Gerardo V. Bayugo OIC, Undersecretary of Health
Dr. David J. Lozada, Jr. Undersecretary of Health
Dr. Teodoro J. Herbosa Undersecretary of Health
Dr. Paulyn Jean B. Rosell-Ubial Assistant Secretary of Health
Director Irma Asuncion, MD National Center for Health Promotion/ Center
for Health Development Metro Manila
Ms. Brenda Panganiban Bureau of International Health Cooperation
Engr. Aida Angeles Bureau of Health Facilities and Services
Ms. Donatilla Esplanada National Center for Health Facility
Development
Engr. Jose Zipagan Center for Health Development Cagayan
Valley
Dr. Rhodora Cruz Center for Health Development Central
Luzon
Ms. Gina Manlapig Center for Health Development Central
Luzon
Mr. Elmer Valiente Center for Health Development Central
Luzon
Mr. Rogelio Millare Center for Health Development Central
Luzon
Mr. Edwin Bautista Center for Health Development Central
Luzon
Engr. Manuel Castro Center for Health Development Central
Luzon
Director Benito Arca, MD Center for Health Development Central
Luzon
Director Rio Magpantay, MD Center for Health Development Central
Luzon
Mr. Vivencio Ediza, Jr. Center for Health Development Central
Visayas
Dr. Jocelyn Abellana Center for Health Development Central
Visayas
Mr. Nelson Cara Center for Health Development- CAR
Engr. Nilo Marayag Center for Health Development Metro
Manila
Mr. Alejandre Mercado Center for Health Development
MIMAROPA
Dr. Renato Dimayuga Batangas Regional Hospital
Dr. Nenita Moraga-Po Chief of Hospital, Celestino Gallares
Memorial Regional Hospital
xii
xii
Dr. Epifania S. Simbul Corazon Locsin Montelibano Memorial

Regional Hospital/ National Childrens
Hospital
Dr. Alberto C. de Leon Eastern Visayas Medical Center
Ms. Crisanta Cruz Florencio V. Bernabe Memorial Hospital
Dr. Maria Lourdes Otayza Mariano Marcos Memorial Hospital
Ms. Almeida Invencion Mariano Marcos Memorial Hospital
Mr. Philip Dasaua Paulino J. Garcia Memorial Research and
Medical Center
Ms. Ma. Evelina Budlong Schistosomiasis Control and Research
Hospital
Dr. Rolando Tacau Valenzuela City Emergency Hospital
Mr. Allan Gabito Valenzuela City Emergency Hospital
Dr. Gerardo Aquino, Jr. Vicente Sotto Memorial Medical Center
Mr. Joseph Al Abuen Vicente Sotto Memorial Medical Center
Ms. Esther Nievales Western Visayas Medical Center
United Nations Development Programme

Dr. Jorge Emmanuel UNDP-GEF Project, Global Project Team
Mr. Romulo Kintanar United Nations Development Program,
Philippines
Mr. Hitoshi Katayama UNDP-GEF Project, Philippines
Department of Environment and Natural Resources

Engr. Geri Geronimo Saez Environmental Management Bureau
Mr. Solon Rativo Environmental Management Bureau
Mr. Gilbert Gonzales Environmental Management Bureau
Mr. Eligio Ildifino Environmental Management Bureau
Ms. Grace Madelar Environmental Management Bureau
Mr. Dennis John Cabanolan Environmental Management Bureau
Ms. Annabeth Roble Environmental Management Bureau
Central Visayas
Other Organizations
Cagayan De Oro Medical Center, Cagayan de Oro City
Cebu Doctors University Hospital, Cebu City
Cebu North General Hospital, Cebu City
Chevalier Enviro Services, Inc., Paranaque City
City Health Office Mandaluyong
City Health Office Navotas
City Health Office Olongapo
City Health Office Puerto Princesa
City Health Office San Juan
City Health Office Taguig
City Health Office Valenzuela
Office of the City Administrator Manila
xiii
xiii
De La Salle Medical Center, Dasmarinas, Cavite

Health Care Without Harm Southeast Asia
Isaac Catalina Medical Center, Balanga City
Las Pinas General Hospital and Satellite Trauma Center, Las Pinas City
Manila Central University Medical Foundation Hospital, Caloocan City
Mt. Carmel Medical Center, Bocaue, Bulacan
Pasay City General Hospital
Philippine Hospital Association
Private Hospital Association of the Philippines
Philippine Nurses Association
Provincial Health Office La Union
Provincial Health Office Leyte
Provincial Health Office Occidental Mindoro
Provincial Health Office Eastern Samar
Safewaste Inc., Pampanga
St. Lukes Medical Center, Taguig City
San Juan De Dios Educational Foundation Inc. (Hospital)
San Juan Medical Center, San Juan
University of the Philippines- College of Public Health, Manila
The Medical City, Pasig City
University of Santo Tomas Hospital, Manila
xiv
xiv
Table of Contents
PREFACE ix
ACKNOWLEDGMENT x
ABBREVIATIONS xix
PART 1: GENERAL CONSIDERATIONS AND OVERVIEW
CHAPTER 1: INTRODUCTION
1.1 Background 1
1.2 Purpose and Intent 1
1.3 Scope and Limitations 2
1.4 Contents of the Manual 2
1.5 Approach 2
1.6 Concepts 3
1.7 Expected Outcome 7
CHAPTER 2: HEALTHCARE WASTE AND ITS IMPACT

2.1 Definition 8
2.2 Categories of Healthcare Waste 8
2.3 Sources and Composition of Healthcare Waste 19
2.4 Impacts of Healthcare Waste to Human Health and the 21
Environment
CHAPTER 3: LEGISLATIONS, POLICIES AND GUIDELINES

3.1 International Agreements 28
3.2 National Laws and Policies 29
PART II: HEALTHCARE WASTE MANAGEMENT SYSTEM
CHAPTER 4: WASTE MINIMIZATION

4.1 Waste Minimization 42
4.2 Principles of Waste Minimization 43
4.3 Administrative Control Measures 48
4.4 Benefits of Waste Minimization 49
CHAPTER 5: SEGREGATON, COLLECTION, STORAGE AND

TRANSPORT
5.1 Waste Segregation 50
5.2 Waste Storage 58
5.3 Collection and Transport of Healthcare Waste 62
CHAPTER 6: WASTE TREATMENT AND DISPOSAL SYSTEM

6.1 Healthcare Waste Treatment 69
6.2 Selection Criteria of Healthcare Waste Treatment Technology 70
6.3 Healthcare Waste Treatment Technologies and Processes 72
6.4 On-Site Waste Treatment Facilities 76
6.5 Waste Disposal System 77
6.6 Summary of Healthcare Waste Handling 81
xv
CHAPTER 7: MANAGING WASTEWASTER GENERATED BY

HEALTHCARE FACILITIES
7.1 Composition of Wastewater 87
7.2 Sources of Wastewater and Its Characteristics 87
7.3 Collection, Treatment and Disposal of Wastewater 89
7.4 Connection of HCF Wastewater to a Centralized Wastewater 89
System
7.5 On-Site Wastewater Treatment Plant 89
7.6 Factors to be Considered in the Establishment of an On-Site WTP 92
7.7 Operation, Maintenance and Monitoring of the WTP 92
PART III: ADMINISTRATIVE CONTROLS AND REQUIREMENTS
CHAPTER 8: ADMINISTRATIVE REQUIREMENTS

8.1 Oversight and Management at the National and Local Levels 99
8.2 Administrative Requirements at the Healthcare Facility 101
8.3 Communication and Training 114
8.4 Budgetary Requirements 119
CHAPTER 9: HEALTH AND SAFETY PRACTICES

9.1 Principles 124
9.2 Education, Training and Awareness of Healthcare Facility Workers 124
9.3 Workers Protection 124
9.4 Personal Protective Equipment (PPE) 125
9.5 Occupational Health and Safety Program 126
9.6 Emergency Management Plan 130
PART IV: GLOSSARY, ANNEXES AND REFERENCES
GLOSSARY 143
ANNEXES 146
REFERENCES 188
xvi
LIST OF TABLES
Table 2.1 Categories of Healthcare Waste 9

2.2 Cytotoxic Drugs Hazardous to Eyes and Skin 14
2.3 Examples of Chemical Waste Commonly Found in 15
Any HCF
2.4 Sources and Categories of HCW Generated 20
2.5 Potential Infections Caused by Exposure to Healthcare 24
Waste, Causative Organisms and Transmission
Vehicles
3.1 On-Line Links to Legislations, Policies and Guidelines 35
5.1 Labelling, Marking and Color-coding of Plastic Liners 52
and Waste Bins
6.1 Acceptable Technologies and Methods Used in the 73
Treatment of Healthcare Waste
6.2 Healthcare Waste Handling 82
7.1 Sources of Wastewater and Its Characteristics 88
8.1 List of Forms to be Submitted by the HCF 114
9.1 Procedures for Emergency Response to Waste Spills 136
LIST OF FIGURES
Figures 1.1 Chain of Infection 4

1.2 Healthcare Waste Management Hierarchy 6
2.1 Examples of Infectious Waste 11
2.2 Examples of Sharps 12
2.3 Examples of Pathological and Anatomical Waste 12
2.4 Example of Cytotoxic Pharmaceuticals 13
2.5 Examples of Chemical Wastes 15
2.6 Examples of Wastes Containing Heavy Metals 16
2.7 Examples of Radioactive Waste 17
2.8 Example of Recyclable Waste 17
2.9 Example of Biodegradable Waste 18
2.10 Example of Non-Recyclable /Non-Biodegradable 19
Waste
2.11 Composition of Healthcare Waste in Metro Manila 19
4.1 Healthcare Waste Handling 41
5.1 Sample Tag Used in HCF 54
5.2 EMB and Other Universally Accepted Hazard Symbols 55
5.3 Examples of Bins and Liners Used in HCF 57
5.4 Example of Sharp Containers Used in HCF 57
5.5 Example of Containers for Chemical and 57
Pharmaceutical Waste Used in HCF
5.6 Cytotoxic Waste Label 58
xvii
5.7 Sample Central HCW Storage for Hazardous and 60

General Waste Including Separate Storage for Condemned
Fluorescent and Busted Lamps.
5.8 Empty Bins Stored at Radiology Department 61
5.9 Sample of HCF Management of Mercury Containing 61
Devices
5.10 On-site Collection of Healthcare Waste 63
5.11a Sample of Dedicated Trolley for Infectious and 63
General Waste
5.11b Single trolley with Heavy Duty Wheels 64
5.12 HCW Handlers with Appropriate PPE 64
5.13 Sample Transport Route Plan for Healthcare Waste 65
6.1 Autoclave 76
6.2 Metro Clark Sanitary Landfill 78
6.3 Safe Burial Pit 79
6.4 Concrete Vault 81
7.1 Wastewater Treatment Plant 90
7.2 Flow of Wastewater from HCF Departments to the QTP 94
7.3 Flow of Wastewater Within the WTP 94
8.1 Linkages of Key Personnel Involved in Healthcare 108
Waste Management
8.2 Life Cycle Stages 111
8.3 The EMS Cycle 112
8.4 IEC Material: Leaflet Given to Patients Upon 118
Admission to the Hospital
9.1 Personal Protective Equipment 125
9.2 Procedures for Proper Handwashing 128
9.3 Procedures for Proper Handrubbing 129
9.4 Needle-Recapper Procedure 133
9.5 Emergency Response to Waste Spillage 137
LIST OF ANNEXES
Annex A World Health Organization Technical Guidelines 146

B Consignment Note 148
C Sample Self-Monitoring Sheet 149
D Sample Monitoring Tool for the Waste Collector 151
E Sample Occupational Incident/Accident Report Form 152
F Sample Flowchart on the Management of Occupational 154
Accident/Incident for Tertiary Hospitals
G Advantages and Disadvantages of the Different Types 155
of WTP
H Joint DENR-DOH Administrative Order No. 02,s.2005 157
I DOH Administrative Order No. 2008-0021 170
J DOH Department Memorandum No. 2011-0145 175
xviii
ACRONYMS
Abbreviations
ABR : Anaerobic Baffled Reactor
ADB : Asian Development Bank
AIDS : Acquired Immune Deficiency Syndrome
AO : Administrative Order
AOX : Adsorbable Organically Halogen
APP : Annual Procurement Plan
BHDT : Bureau of Health Devices and Technology
BHFS : Bureau of Health Facilities and Services
BHS : Barangay Health Station
BOD : Biological Oxygen Demand
BP : Blood Pressure
CAT : Costing Analysis Tool
CD : Cleaning and Disinfection
CDC : Center for Disease Control and Prevention
CH4 : Methane
CHD : Center for Health Development
CO2 : Carbon Dioxide
COC : Chief of Clinics
COD : Chemical Oxygen Demand
CPH : College of Public Health
CPR : Certificate of Product Registration
DAP : Differently Abled Person
DBP : Development Bank of the Philippines
DENR : Department of Environment and Natural Resources
DILG : Department of Interior and Local Government
DNA : Deoxyribonucleic Acid
DOH : Department of Health
EAMC : East Avenue Medical Center
ECAT : Expanded Costing Analysis Tool
ECC : Environmental Compliance Certificate
EHS : Environmental Health Service
EIA : Environmental Impact Assessment
EIS : Environmental Impact Statement
EISCP : Environmental Infrastructure Support Credit Program
EMB : Environmental Management Bureau
EMS : Environmental Management System
EO : Executive Order
EOHO : Environmental and Occupational Health Office
EUFS : Environmental User Fee System
FDA : Food and Drug Administration
FEFO : First to Expire, First Out
FIFO : First In, First Out
GEF : Global Environment Facility
GPP : Green Procurement Policy
xix
HCF : Healthcare Facility/ies

HCW : Healthcare Waste
HCWH : Health Care Without Harm
HCWM : Healthcare Waste Management
HCWMC : Healthcare Waste Management Committee
HCWMP : Healthcare Waste Management Plan
HDPE : High Density Polyethylene
HEMS : Health Emergency Management Service
HEICS : Hospital Emergency Incident Command System
HEPA : High Efficiency Particulate Air
HFCs : Hydrofluorocarbons
HIV : Human Immunodeficiency Virus
IC : Infection Control
ICN : Infection Control Nurse
ICO : Infection Control Officer
ICU : Intensive Care Unit
IEC : Information, Education and Communication
IEE : Initial Environmental Examination
IRR : Implementing Rules and Regulations
ISO : International Organization for Standardizatoin
IV : Intravenous
JAO : Joint Administrative Order
LCA : Life Cycle Analysis
LGU/s : Local Government Unit/s
LLDA : Laguna Lake Development Authority
LTO : License to Operate
MC : Memorandum Circular
MCCII : Medical Center Chief II
MSDS : Material Safety Data Sheet
N2O : Nitrous Oxide
NaClO : Sodium Hypochlorite
NCDPC : National Center for Disease Prevention and Control
NCHFD : National Center for Health Facility Development
NEC : National Epidemiology Center
NPCC : National Pollution Control Commission
NRL : National Reference Laboratory
NSWMC : National Solid Waste Management Commission
OIC : Officer in Charge
OIR : Occupational Incident Report
OPD : Out Patient Department
OR : Operating Room
OSHA : Occupational Safety and Health Administration
PAM : Physical Asset Management
PCO : Pollution Control Officer
PD : Presidential Decree
PDCA : Plan-Do-Check-Act
xx
ACRONYMS
PET : Polyethylene Terephthalate

PFCs : Perfluorocarbons
PGH : Philippine General Hospital
pH : Power of Hydrogen
PHIC : Philippine Health Insurance Corporation
PIO : Public Information Office
PME : Professional Mechanical Engineer
PMP : Preventive Maintenance Program
PNRI : Philippine Nuclear Research Institute
POPs : Persistent Organic Pollutants
PPE : Personal Protective Equipment
PTB : Pulmonary Tuberculosis
PVC : Polyvinyl Chloride
RA : Republic Act
RBC : Rotating Biological Contractors
RHU : Rural Health Unit
SACCL STD AIDS Central Cooperative Laboratory
SARS : Severe Acute Respiratory Syndrome
SBR : Sequential Batch Reactor
SF6 : Sulphur Hexafluoride
SHO : Senior House Officer
SO : Safety Officer
STP : Sewage Treatment Plant
TSD : Treatment, Storage and Disposal
TSE : Transmissible Spongiform Encephalitis
TSS : Total Suspended Solid
TWG : Technical Working Group
UNDP : United Nations Development Program
UNFCCC : United Nations Framework Convention on Climate Change
UP : University of the Philippines
UV : Ultraviolet
WHO : World Health Organization
WMO : Waste Management Officer
WMP : Waste Minimization Program
WPRO : Western Pacific Regional Office
WTP : Wastewater Treatment Plant
xxi
3rd Healthcare Waste Management Manual March 2011 Page xxii
PART 1
GENERAL
CONSIDERATIONS
AND
OVERVIEW
xxiv
INTRODUCTION
CHAPTER 1: INTRODUCTION
1.1 Background
The First Edition of the Hospital Waste Management Manual was formulated and
issued through the Environmental Health Service (EHS), Department of Health (DOH)
in 1997. In 2004, the DOH, through the Environmental and Occupational Health
Office (EOHO) in consultation with other stakeholders, issued for implementation the
Second Edition of the Manual renamed as Healthcare Waste Management (HCWM)
Manual. The Second Edition Manual was primarily designed to provide healthcare
facilities (HCF) and other stakeholders with guidance and practical information
regarding safe, efficient and environment-friendly waste management options. This
has been implemented in all HCF in the country.
However, with the onset of new technologies and promulgations of new laws and
issuances, there is an urgent need to review and revise the Second Edition Manual
in order to provide a more effective and efficient approach in implementing an
appropriate and holistic waste management in any HCF. The DOH, in partnership
with the World Health Organization (WHO), Health Care Without Harm (HCWH),
University of the Philippines (UP) College of Public Health (CPH), and the Department
of Environment and Natural Resources (DENR), assisted by the United Nations
Development Programme (UNDP) Global Environment Facility (GEF), has been
launching programs and projects geared towards the promulgation and formulation of
policies relevant to HCWM.
Thus, DOH created a Technical Working Group (TWG) to review, enhance and
update the DOH policies and manual of guidelines on HCWM. The primary task of
the TWG is to come up with a more user-friendly manual on HCWM substantiated
with the new trends and technologies adopted and accepted universally. Series of
consultative meetings with healthcare administrators, DOH partners, and stakeholders
were conducted to be abreast with, to gather information, and to clarify issues and
concerns relevant to HCWM.
1.2 Purpose and Intent

The Third Edition also called Manual on Healthcare Waste Management will serve
as a reference for HCF administrators in the implementation of an effective and efficient
waste management program. The requirements for doing such are provided in the
manual by listing the standards of performance, defining the mandatory requirements,
providing new concepts, and by citing examples and tools. The Manual is designed to
be used by all workers within the HCF whether it is a government HCF, private HCF,
Rural Health Units (RHUs), Barangay Health Stations (BHS), clinics, and private
service providers who are involved in the segregation, collection, handling, storage,
treatment and disposal of healthcare waste (HCW).
1
This Manual will also serve the purpose and activities of the regulators, policy
makers, development organizations, voluntary groups, environmental groups and
practitioners, advisers, researchers, and students.
1.3 Scope and Limitations

The Third Edition Manual covers all HCW produced or generated by HCFs,
except other types of general wastes, such as condemned equipment, spare parts,
tires, scrap and the like. These are already bound by special laws, such as existing
auditing and accounting rules and regulations for government agencies and internal
laws and policies of private HCF. Also, HCW generated by households, ear piercing
and tattoo parlors, mortuary and autopsy centers outside of an HCF, pharmaceutical
and chemical establishments and other establishments that are not considered as HCF
are not covered by this Manual and are covered by existing environmental laws and
policies of the different governing agencies other than the DOH.
1.4 Contents of the Manual

The Third Edition Manual on Healthcare Waste Management is composed of four
(4) parts, each part is subdivided into different chapters:
Part I includes the general description of HCW, an overview, categories,

composition, and its impacts to human health and environment. It also includes the
different laws, policies, and concepts applicable to HCWM.
Part II discusses the main components of the Manual which includes the different
principles and policies on HCWM. The HCW generated within an HCF shall follow
an appropriate and well identified stream from waste generation, waste segregation,
collection, transportation (on-site and off-site), storage, treatment to final disposal.
It also discusses water quality and wastewater management.
Part III contains administrative and financial requirements to implement HCWM
and various administrative controls such as health and safety practices (particularly
on infection control), emergency management, communication and training.
Part IV contains the appendices.
1.5 Approach
The DOH recognizes the critical impact of proper HCWM and its responsibility
in setting up necessary policies, guidelines, and standards for safe management of
HCW. The DOH also acknowledges its responsibility in ensuring that all concerned
individuals assume their share of responsibility and strictly comply with existing laws
and regulations on the effective and efficient handling of wastes, and in imposing
discipline.
To address the issues at hand, the following approaches will be undertaken:
2
INTRODUCTION
Clear definition of hazardous HCW, its various categories, and the hazards/risks
involved;
Application of concepts that can minimize risks to the patients, HCF workers
and the environment such as Chain of Infection, International Organization for
Standardization (ISO) hierarchy of controls and the HCWM hierarchy;
Installation of appropriate monitoring system to ensure strict enforcement of the
laws, policies, and guidelines in all concerned HCF;
Continuous review of the applicability of the policies, guidelines and standards vis
a vis latest standards, trends and technologies.
1.6 Concepts
1.6.1 Chain of Infection
The Chain of Infection is a model used to understand the infection process. The
chain of infection is a circle of links, each representing a component in the cycle. Each
link must be present and in sequential order for an infection to occur. The links are:
infectious agent, reservoir, portal of exit from the reservoir, mode of transmission, and
portal of entry into a susceptible host. Understanding the characteristics of each link
and the means by which the chain of infection can be interrupted provides the HCF
workers with methods for supporting vulnerable patients, preventing the spread of
infection and self-protection. Breaking any link in the chain will prevent infection,
although control measures are most often directed at the mode of transmission.
The transmission of infection and its control is illustrated by the chain of infection in
Figure 1.1.
The elements of infection in the context of HCW are:
Some components of HCW are potential reservoir of disease-causing microorganisms

such as culture dishes, liquid blood, pathological waste, etc.
The infective dose depends on the virulence of the microorganisms, the portal of
entry, and the susceptibility of the host.
Modes of transmission may involve contact (e.g. contaminated needles or blood
splatter), vehicle-borne (e.g. contaminated wastewater), air-borne (e.g. aerosolized
pathogens from broken culture dishes or the rapture of yellow bags), and vector-
borne (e.g. rodents in an HCW storage area) transmission.
Portals of entry include breaks in the skin and mucous membranes (e.g. needle-
stick injuries or blood splashes into the mucous membranes), the respiratory tract
(inhalation of pathogenic aerosols), etc.
Potential susceptible host include HCF workers, waste handlers, patients and
visitors in the HCF, landfill operators, scavengers and the general public.
The consequences of improper handling and disposal of HCW are serious. For example,
the reuse of improperly discarded needles by intravenous (IV) drug users or accidental
3
needle stick
needle stickinjuries
injuriessuffered
sufferedbybyrecyclers
recyclerssifting
siftingthrough
through waste
waste dumps
dumps could
could leadlead to
to the
the spread of hepatitis B, HIV-AIDS and other blood-borne
spread of hepatitis B, HIV-AIDS and other blood-borne diseases. diseases.
Susceptible Host
A person who cannot resist a pathogen
invading the body, multiplying and
resulting in infection. The Host is
susceptible to the disease, lacking
immunity or physical resistance to
overcome the invasion by the
pathogenic microorganism.
Infectious Agent
A microbial organism with the ability to
cause disease. The greater the Portal of Entry
An opening allowing the microorganism
organism's virulence (ability to grow to enter the host. Portals also result
and multiply), invasiveness (ability to from tubes placed in body cavities,
enter tissue) and pathogenicity (ability such as urinary catheters or from
to cause disease), the greater the punctures produced by invasive
possibility that the organism will cause procedures such as intravenous fluid
an infection. Infectious agents are replacement
bacteria, viruses, fungi and parasites.
Reservoir Mode of Transmission

A location within which Method of transfer by which the
microorganisms can thrive and organism moves or is carried from
reproduce. For example, one place to another. The hands of
microorganisms thrive in human the healthcare worker may carry
beings, animals and inanimate bacteria from one person to
objects such as water, table tops another.
and door knobs.
Portal of Exit
An opening providing a way for a
microorganism to leave the reservoir.
For example, the microorganism may
leave the reservoir through the nose or
mouth when someone sneezes or
coughs. Microorganisms, carried away
from the body by feces, may also leave
the reservoir of an infected.
Figure 1.1 Chain of Infection
1.6.2 Hierarchy of Controls

1.6.2 Hierarchy of Controls
Controlling exposures to occupational hazards is the fundamental method of protecting
Controlling exposures to occupational hazards is the fundamental method of
workers. Hierarchy of controls has been used as a means of determining feasible and
protecting workers. Hierarchy of controls has been used as a means of determining
effective controls. One representation of this hierarchy can be summarized as follows:
feasible and effective controls. One representation of this hierarchy can be summarized
asfollows:
Elimination
Substitution
Elimination
Engineering controls
Substitution
Administrative controls
Engineering controls
Personal Protective Equipment
Administrative controls
4 Personal Protective Equipment
4
INTRODUCTION
The methods at the top of the list are potentially more effective and protective than
those at the bottom. Following the hierarchy normally leads to the implementation of
inherently safer systems, where the risk of illness or injury is substantially reduced.
Elimination and substitution, while most effective at reducing hazards, also tend
to be the most difficult to implement in an existing process. If the process is still at
the design or development stage, elimination of hazard and substitution of control
may be inexpensive and simple to implement. On existing process, major changes in
equipment and procedures may be required to eliminate hazards or substitute control.
Engineering Control is used to remove a hazard or place a barrier between the

worker and the hazard. This includes designing the facility, equipment and processes
to eliminate or minimize the hazards; substituting the processes, equipment, devices,
materials or other factors to lessen the hazards; isolating the hazard by enclosing the
source or putting barriers between the source of hazard and the exposed workers;
using interlocks, machine guards, blast sheets, protective curtains and/or other means;
removing or redirecting the hazard using local exhaust ventilation; and adopting
complete mechanization or computerization.
Well-designed engineering controls can be highly effective in protecting workers
and are typically independent of worker interactions. The initial cost of engineering
controls can be higher than the cost of administrative controls or PPE, but over the
long term, operating costs are frequently lower, and in some instances, can provide
cost savings in other areas of the process.

Administrative Control includes assessment of risks, medical controls including
provision of PPEs, establishment of waste management policies, procedures, guidelines
and activities, conduct of regular and effective training, management of human
resources and procurement of appropriate equipment and supplies. Administrative
controls and PPE are frequently used with existing processes where hazards are not
particularly well controlled. While relatively inexpensive to establish, it can be very
costly to sustain over the long term. These methods for protecting workers have also
proven to be less effective than other measures, requiring significant effort by the
affected workers. Medical control includes written policies with standard operating
procedures on the following.
a) Patient Safety which includes proper patient identification, assurance of blood

safety, safe clinical and surgical procedures, provision and maintenance of safe
quality drugs and technology, strengthening of infection control, maintenance
of environment care standards and energy/waste management standards.
Administrative Order 2008-0023 of the DOH requires Patient Safety program to
have the key elements of leadership, institutional development, reporting system,
feedback and communication, adverse event prevention and risk management,
5
MANUAL ON HEALTHCARE
disclosure WASTE
of reported MANAGEMENT,
serious THIRD EDITION
events, professional development, and a patient
centered care and empowerment.
b) Occupational
disclosure Healthserious
of reported and Safety
events,which includesdevelopment,
professional physical examination (pre-
and a patient
employment
centered care andand annual), regular immunization, health education and wellness,
empowerment.
and continuous
b) Occupational medical
Health andmonitoring
Safety whichand periodic
includesevaluation
physical ofexamination
safety measures.
(pre-
employment and annual), regular immunization, health education and wellness, and
PPEcontinuous
is specialized clothing
medical or equipment
monitoring worn by
and periodic a workerofdesigned
evaluation to protect against
safety measures.
infectious materials or from exposure to infectious agents thus, preventing injury or
PPE is specialized clothing or equipment worn by a worker designed to protect against
illness from a specific hazard. Adequate and appropriate PPE shall be provided to
infectious materials or from exposure to infectious agents thus, preventing injury or
HCF workers who are exposed to hazardous waste. This includes protection for the
illness from a specific hazard. Adequate and appropriate PPE shall be provided to HCF
whole body head, face, body, arms, legs and feet.
workers who are exposed to hazardous waste. This includes protection for the whole
body head, face, body, arms, legs and feet.
1.6.3 Healthcare Waste Management Hierarchy
The
1.6.3 HCWM hierarchy
Healthcare as shown inHierarchy
Waste Management Figure 1.2 illustrates that it is most preferable to
The HCWM hierarchy as shown in Figureand
prevent the generation of waste at source 1.2reduce the quantity
illustrates that it isofmost
waste generated
preferable to
by adopting different methods of safe re-use, recycling and recovery.
prevent the generation of waste at source and reduce the quantity of waste generated Proper treatment
by
and residuals
adopting disposal
different methodsareofthesafe
endre-use,
of pipe approach.
recycling In addressing
and recovery. HCWM,
Proper waste
treatment and
minimization basically utilizes the first two elements that could
residuals disposal are the end of pipe approach. In addressing HCWM, waste help reduce the bulk of
HCW for disposal; so the best waste management practice aims to address
minimization basically utilizes the first two elements that could help reduce the bulk of
the problem
at source (green procurement approach) rather than the end of pipe solution .
HCW for disposal; so the best waste management practice aims to address the problem at
source (green procurement approach) rather than the end of pipe solution.
Most Preferable
Prevent
GREEN
PROCUREMENT
Reduce
Reuse
RESOURCE
Recycle
DEVELOPMENT
Recover
Treat
END OF PIPE
Dispose
Least Preferable
Figure 1.2 Healthcare Waste Management Hierarchy
6
6
INTRODUCTION
1.7 Expected Outcome

All HCF have the responsibility of ensuring that there are no adverse health effects
and environmental consequences resulting from their generation, collection, storage,
treatment and disposal of HCW. With the application of the different approaches
discussed and illustrated in the Third Edition Manual, the user will be able to install an
appropriate waste management system that would best meet the needs of their HCF.
Proper and strict compliance with the set standards will result to benefits such as those
shown below:
Protection of human health by controlling and/or reducing exposure of HCF
workers, patients, visitors, comforters and the general public to hazardous HCW
and minimizing indirect impacts from environmental exposures to HCW
Progress in the compliance of HCF with set regulatory laws, policies and guidelines
Boosting of community ecological awareness and relationship by demonstrating
commitment and dedication in the implementation of HCWM programs and
activities
Contribution to the global effort to save Mother Earth from destruction caused by
pollution and contaminants resulting from improper handling of HCW
Prevention of any long-term liability resulting to any contravention or violation
incurred in the implementation of HCWM laws
Improvement of socio-economic benefits resulting from the effective and efficient
application of HCWM laws, policies and procedures.
7
Chapter 2: Healthcare Waste and its Impact

For a clearer understanding and appreciation of HCW, this Chapter will provide
the definition, the types of waste generated in any HCF, the hazards/risks that waste
produces, its impact on the people, community and the environment.
2.1 Definition
Healthcare waste (HCW) includes all the solid and liquid wastes generated as a
result of any of the following:
Diagnosis, treatment or immunization of human beings;

Research pertaining to the above activities;
Research using laboratory animals for the improvement of human health;
Production or testing of biologicals; and
Other activities performed by HCF
Healthcare Facilities (HCF), for this purpose, are public, private and non-
governmental institutions/facilities that contribute to the improvement of the health
status of an individual, which includes:
Hospitals and medical centers

Clinics and healthcare units related to patient care including but not limited
to dispensaries, alternative medicine clinics; obstetrics and maternity lying-
in clinics; out-patient clinics; dialysis centers; drug testing centers; transfusion
centers; military medical services; prison hospital and clinics; emergency medical
care services; physicians offices/clinics; dental clinics; specialized healthcare
establishments such as convalescing homes and Differently Abled Person (DAP)
centers; derma, vein and skin clinics
Rehabilitation centers, hospices, psychiatric centers, and centers providing long-
term healthcare services
Related laboratories and research centers such as medical and bio-medical
laboratories, biotechnology laboratories and institutions, medical research centers,
blood banks and blood collection services, nuclear medicine laboratories, animal
research laboratories
Ambulance and emergency care mobiles (including medical mission and health
services provided in evacuation centers)
Teaching and training hospitals and medical schools
2.2 Categories of Healthcare Waste

There are seven (7) categories of HCW generated in HCF for easy identification
of the handling, mode of treatment and proper disposal. Table 2.1 illustrates the
description and examples per category.
8
HEALTHCARE WASTE AND ITS IMPACT
Table 2.1 Categories of Healthcare Waste
CATEGORY DESCRIPTION EXAMPLES
Infectious All waste suspected to contain pathogens Solid wastes from

(or their toxins) in sufficient concentration patients with infectious
to cause diseases to a potential host. disease (e.g., dressings,
swabs, blood bags, urine
bag , sputum cups)
Discarded materials or equipment used Liquid wastes from

for diagnosis, treatment and prevention of patients with infectious
disease of patients with infectious disease disease (e.g., feces,
urine, blood or other
body secretions).
Highly infectious waste include microbial Food wastes (liquid or

cultures and stocks of highly infectious solid) of patients with
agents from Medical Analysis Laboratories highly infectious disease
and biofluids from patients with highly
infectious diseases. (These require
disinfection at source)
Sharps Items that can cause cuts or puncture Used or expired sharps
wounds. e.g., hypodermic,
intravenous or other
needles; auto-disable
syringes; syringes
with attached needles;
infusion sets; scalpels;
pipettes; knives; blades;
broken glass; wet
ampules
Except syringes and

needles used for
antineoplastic purposes
Pathological Refers to tissue sections and body Placenta, internal
and material derived from biopsies or surgical organs, tissues used for
Anatomical procedures that are then examined in the diagnostic procedures
laboratory. such as biopsy, blood,
fetus
Anatomical waste is a subgroup of Amputated body parts

pathological waste. This type of waste like legs.
refers to recognizable human body parts
such as amputated limbs, etc.
9
CATEGORY DESCRIPTION EXAMPLES
Pharmaceutical Refers to expired, spilt and contaminated Empty vials, bottles,

Waste pharmaceutical products, drugs and connective tubing
vaccines. Also refers to discarded items
used in handling pharmaceuticals.
Pharmaceutical wastes include Medical supplies and

antineoplastic, cytotoxic, and genotoxic containers of cytotoxic
waste. Drugs usually used in oncology drugs or chemicals;
(antineoplastic drugs) or radiotherapy
units have a high hazardous mutagenic
or cytotoxic effect.
Chemical Waste Discarded chemicals (solid, liquid, or Laboratory reagents, film
gaseous) generated during disinfecting developer, disinfectants
and sterilizing procedures and soaking solutions,
solvents
Chemical wastes can be further Concentrated ammonia

classified into corrosive, reactive, toxic solutions, concentrated
and flammable hydrogen peroxide,
chlorine, silver nitrate
Chemical wastes also include wastes Cadmium, mercury from

with high content of heavy metals and broken thermometers,
their derivatives sphygmomanometers
Radioactive Wastes exposed to radionuclide. Cobalt (60 Co),
Waste Residues from shipment of radioactive Technetium (99 Tc),
materials and unwanted solution of Iodine (131 I) and Iridium
radionuclides intended for diagnostic or (192 r)
therapeutic use.
Liquids, gas and solids contaminated Contaminated waste,

with radionuclides whose ionizing patients excretion and
radiations have genotoxic effects. all materials used by
patients exposed with
radionuclides within 48
hours
Non-Hazardous Waste that has not been in contact with Papers, cardboards,
or General communicable or infectious agents, empty bottles, tetra
Waste hazardous chemicals or radioactive packs, scrap materials,
substances, and does not pose a hazard pressurized containers,
office wastes, food waste
and other materials
of patients with non-
communicable disease,
x-ray plates
10
2.2.1 Infectious Waste

These are wastes that are most likely to contain pathogens (bacteria, viruses, parasites
or fungi) in sufficient concentration or quantity to cause diseases in susceptible hosts
which includes:
Figure 2.1 Examples of Infectious Waste
cultures and stocks of infectious agents from laboratory work; waste from surgeries
and autopsies (e.g. tissues, materials or equipment that have been in contact with
blood or other body fluids);
waste from infected patients in isolation wards (e.g. excreta, dressings from infected
or surgical wounds, clothes heavily soiled with human blood or other body fluids);
waste that have been in contact with infected patients undergoing haemodialysis
(e.g. dialysis implements such as tubing and filters, disposable towels, gowns,
aprons, gloves and laboratory coats); infected animals from research laboratories;
any other instruments or materials that have been in contact with infected persons
or animals.
Among these, highly infectious wastes are wastes from microbial cultures and
stocks of highly infectious agents from medical analysis laboratories. Body fluids
from patients with highly infectious diseases are also considered as highly infectious
waste. Highly infectious disease refers to those causative organisms under Biosafety
Levels III and IV, such as Severe Acute Respiratory Syndrome (SARS), Human
Immunodeficiency Virus (HIV), Acquired Immunodeficiency Syndrome (AIDS),
pulmonary tuberculosis (PTB), anthrax and ebola (WHO Laboratory Biosafety
Manual, 3rd edition, 2004).
11
The DOH Administrative Order 2010-33 considers diseases such as

meningococcemia, viral haemorrhagic fevers, the plague, hepatitis B and C, rabies,
invasive group A streptococcal infections, and transmissible spongiform encephalitis
(TSE) such as Mad Cow Disease and Creutzfeldt-Jakob disease as highly infectious
and dangerous diseases.
Special requirements regarding management of infectious waste must be imposed
whenever waste is known or based on medical experience expected to be
contaminated with causative agents of diseases and when this contamination gives
cause for concern that the disease might spread.
2.2.2 Sharps
Figure 2.2 Examples of Sharps Waste
Sharps are considered as the most hazardous waste generated in HCF and must be
managed with utmost care. This is because of the double danger it poses. It can cause
injuries through accidental pricks, cuts or punctures. Aside from this, one can also be
infected with a pathogen through these injuries. Examples of sharps include needles,
syringes, scalpels, saws, blades, broken glass, infusion sets, knives, nails and any other
items that can cause a cut or puncture wounds. Whether or not they are infected, such
items are usually considered as highly hazardous HCW.
2.2.3 Pathological and Anatomical Waste
Figure 2.3 Pathological Waste
12
Pathological waste consists of tissues, organs, body parts, blood, body fluids, other
waste from surgery and autopsies, including human fetuses and animal carcasses.
Recognizable human or animal body parts are also called anatomical waste.
2.2.4 Pharmaceutical Waste Including Genotoxic/Cytotoxic/Antineoplastic Waste

Pharmaceutical waste includes expired, spilt and contaminated pharmaceutical
products, drugs, vaccines and sera that are no longer required and need to be disposed
of appropriately. This category also includes discarded items used in handling of
pharmaceuticals such as bottles or boxes with residues, gloves, masks, connective
tubing and drug vials.
Genotoxic waste causes damage to the cells DNA. This includes certain
antineoplastic (anti-tumor) and cytotoxic (cell-killer) drugs. This type of waste is
highly hazardous and may have mutagenic, teratogenic or carcinogenic effects.
Figure 2.4 Examples of Cytotoxic Pharmaceuticals
Harmful cytotoxic drugs can be categorized as follows:
Alkylating Agents: These are also called DNA-damaging agents. These cause
alkylation of DNA nucleotides, which leads to cross-linking and miscoding of the
genetic stock;
Anti-metabolites: These drugs imitate the role of purine and pyrimidine as the
building blocks of DNA. Thus, they inhibit the biosynthesis of nucleic acids in the
cell; mitotic inhibitors: prevent cell division
Plant Alkaloids and Terpenoids: These chemicals inhibit microtubule function
thereby halting cell division. Examples of these are vinca alkaloids derived from
the Catharanthus roseus plant (Common Name: Tsitsirika)
Podophyllotoxins: These compounds are derived from Podophyllum peltatum
(Common Name: Mayapple). They prevent cell division by inhibiting the cell from
entering the G1 Phase. These compounds also affect DNA synthesis
Intercalating Agents: These wedge between the DNA bases, affecting the
structure of the DNA and preventing polymerase and other DNA binding proteins
from functioning properly.
13
Cytotoxic waste is generated from several sources and includes the following:
Contaminated materials from drug preparation and administration, such as syringes,

needles, gauges, vials, packaging, out-dated drugs, excess (left over) solutions and
drugs returned from the wards
Urine, feces and vomits from patients which may contain potentially hazardous
amounts of the administered cytotoxic drugs and/or their metabolites and which
shall be considered genotoxic for at least 48 hours and sometimes up to 1 week after
drug administration.
It is necessary for patients who are taking cytotoxic medication to have a separate
water closet, which is exclusive for the use of these patients. This will ensure that
other patients will not be exposed to cytotoxic drugs. Moreover, it will also ensure
that the urine, vomit, excreta and other body fluids coming from these patients will
be adequately treated before these wastes are mixed with other wastes in the Sewage
Treatment Plant (STP).
Table 2.2 Cytotoxic Drugs Hazardous to Eyes and Skin
Alkylating Agents Vesicant Drugs: aclarubicin,

mechlorethamine,cisplatin, mitomycin
Irritant Drugs: carmustine, cyclophosphamide,
dacarbazine, ifosfamide, melphalan, streptozocin,
thiotepa
Anti-metabolites Irritant: methotrexate, fludarabine, cytarabine
Intercalating Agents Vesicant Drugs: amsacrine, dactinomycin,
daunorubicin, doxorubicin, epirubicin, pirarubicin,
zorubicin
Irritant Drugs: mitoxantrone
Vinca Alkaloids and Vesicant Drugs: vinblastine, vincristine, vindesine,
Derivatives vinorelbine
Podophyllotoxins Irritant Drugs: teniposide
2.2.5 Chemical Waste

Chemical waste consists of discarded solid, liquid and gaseous chemicals used
in diagnostic and experimental work and in cleaning, housekeeping and disinfecting
procedures. Chemical waste from HCF can be hazardous or non-hazardous.
14
Fixing
Solutions
Fixing
Solutions
Figure 2.5 Examples of Chemical Wastes

Figure 2.5 Examples of Chemical Wastes
Chemical waste is considered hazardous if it has at least one of the following properties:
Chemical waste is considered hazardous if it has at least one of the following properties:
Toxic:
Toxic:chemicals
chemicalsthat
that have
have the
the capacity to harm
capacity to harmbiological
biologicaltissue
tissue
Corrosive: chemicals that can cause severe burns to skin
Corrosive: chemicals that can cause severe burns to skin and otherand biological
other biological
tissues
tissues including
including eyes
eyes and and(e.g.
lungs lungs (e.g.
acids ofacids
pH<2ofand
pH<2
basesand bases of pH>12)
of pH>12)
Flammable: chemicals that ignite/burn easily in normal working temperatures (e.g.
Flammable: chemicals that ignite/burn easily in normal working temperatures (e.g.
chemicals with flashpoint below 37.8ooC or 100ooF)
chemicals with flashpoint below 37.8 C or 100 F)
Reactive: chemicals that can react by themselves when exposed to heat, pressure,
Reactive: chemicals that can react by themselves when exposed to heat, pressure,
shock, friction, catalyst presence or by contact with air or water
shock, friction, catalyst presence or by contact with air or water
Table 2.3 Examples of Chemical Wastes Commonly Found in HCF
Table 2.3 Examples of Chemical Wastes Commonly Found in HCF
Chemical Waste Examples
Halogenated solvents chloroform, methylene chloride, perchloroethylene,
refrigerants, trichloroethylene
Non-halogenated solvents acetone, acetonitrile, ethanol, ethyl acetate,
formaldehyde, isopropanol, methanol, toluene, xylenes
Halogenated disinfectants calcium hypochlorite, chlorine dioxide, iodine solutions,
iodophors, sodium dichloroisocyanurate, sodium
hypochlorite (bleach)
Aldehydes formaldehyde, glutaraldehydes, ortho-phthalaldehyde
Alcohols ethanol, isopropanol, phenols
Other disinfectants hydrogen peroxide, peroxyacetic acid, quarternary
amines
Metals arsenic, cadmium, chromium, lead, mercury, silver
Acids acetic, chromic, hydrochloric, nitric, sulfuric
Bases ammonium hydroxide, potassium hydroxide, sodium
hydroxide
Oxidizers bleach, hydrogen peroxide, potassium dichromate,
potassium permanganate
Reducers sodium bisulfite, sodium sulfite
Miscellaneous anaesthetic gases, asbestos, ethylene oxide, herbicides,
paints, pesticides, waste oils
15
15
Non-hazardous chemical waste consists of chemicals with none of the above

properties, such as sugar, amino acids and certain organic and inorganic salts.
Waste with high heavy-metal content represents a subcategory of hazardous
chemical waste, and are usually highly toxic. Heavy metals refer to metallic chemical
elements that have a high density and are relatively toxic at low levels. Heavy metals
have a specific gravity lesser than five times the specific gravity of pure water, which
is 1 at 4oC. These cannot be degraded nor destroyed by the body. Thus, heavy metals
are bio-persistent and tend to bio-accumulate. The following are examples of heavy
metals:
Figure 2.6 Examples of Waste Containing Heavy Metals
Mercury is a naturally occurring silvery-white liquid metal that readily vaporizes.

When released to the air, mercury is transported and deposited globally. Mercury
ultimately accumulates in the lake bottom in the form of sediments, where it is
transformed into its more toxic organic form, methyl mercury, which accumulates
in fish tissue. There are 3 types of mercury: elemental, inorganic and organic.
Mercury waste is typically generated by spillage from broken clinical equipment
(mercury thermometer, sphygmomanometer, etc.). Whenever possible, spilled
drops of mercury shall be recovered. Residues from dental laboratories have high
mercury content.
Cadmium is a soft, bluish white metal that has a rapid electrical and thermal
conductivity. It is highly resistant to stress and corrosion. Cadmium waste comes
mainly from discarded batteries, dental alloys, pigments and electronic devices.
Lead is a bluish white lustrous metal that is highly malleable and ductile. Lead
waste usually comes from batteries, petroleum, rolled and extruded products,
ammunition and pipes. Also, certain reinforced wood panels containing lead is
still being used in radiation proofing in X-ray and diagnostic departments.
16
2.2.6 Radioactive Waste
Figure 2.7 Examples of Radioactive Waste
Radioactive waste includes disused sealed radiation sources, liquid and gaseous
materials contaminated with radioactivity, excreta of patients who underwent
radionuclide diagnostic and therapeutic applications, paper cups, straws, needles and
syringes, test tubes and tap water washings of such paraphernalia. It is produced as a
result of procedures such as in vitro analysis of body tissues and fluids, in vivo organ
imaging, tumor localization and treatment and various clinical studies involving the
use of radioisotopes. Radioactive HCW generally contain radionuclides with short
half-lives, which lose their activity in a shorter time.
2.2.7 Non-Hazardous or General Waste

This includes all the wastes that have not been infected like general office waste,
packaging, leftover food, x-ray plates and non-hazardous pharmaceutical waste. They
are comparable to domestic waste, which does not pose special handling problem or
hazard to human health or to the environment. They comprise around 70% of the
generated waste in any HCF. General waste shall be dealt with by the municipal waste
disposal system.
Non-hazardous or general waste can be further classified into:
2.2.7.1 Recyclable Waste

Examples of common recyclable materials found in HCFs :
Figure 2.8 Examples of Recyclable Waste
v
Paper products: corrugated cardboard boxes, office paper, computer printout paper,
ledger paper, newspaper, magazines
Aluminium: beverage cans, food cans, other aluminium containers
Pressurized Gas Containers: disinfectant sprays, oxygen tanks. Many of these, once
empty or of no further use (although they may still contain residues) are reusable,
but certain types, notably aerosol cans, must be disposed of safely. Whether inert
or potentially harmful, gases in pressurized containers shall always be handled with
care.
Plastics: polyethylene terephthalate (PET) plastic water bottles, PET soft drink
bottles, high density polyethylene (HDPE) plastic milk containers, HDPE containers
for food and mild solutions, polypropylene plastic bottles for saline solutions or
sterile irrigation fluids, polystyrene packaging
Glass: clear glass, colored or mixed glass, crushed vials/ampules
Wood: scrap wood, wood shipping pallets
Durable goods: used furniture, bed frames, carpets, curtains
Electronic Devices: computer equipment, printer cartridges, photocopying toners
2.2.7.2 Biodegradable HCW includes leftover food of patients with non-communicable

disease or garden waste such as cut grasses or tree trimmings that can be composted .
Figure 2.9 Example of Biodegradable Waste
18
2.2.7.3 Non-recyclable/non-biodegradable HCW includes all the non-hazardous or

general wastes that do not belong to the previous two categories (2.2.7.1 and 2.2.7.2 )
Figure 2.10 Example of Non-Recyclable/ Non-Biodegradable Waste
2.3 Sources and Composition of Healthcare Waste

Not all the wastes generated in HCF are hazardous. As demonstrated by Figure 2.11,
most of the wastes generated by HCF are non-hazardous general waste. According to
the Asian Development Bank (ADB), only 30.37% of the wastes coming from HCF
are hazardous. The remaining 69.63% are general waste. It is also estimated in the
same study that a hospital generates an average of 0.34 kg/bed/day of infectious,
sharps and pathological waste and 0.39kg/bed/day of general wastes.
Figure 2.11 Composition of Healthcare Waste in Metro Manila

Source: ADB, 2003
The kind and characteristic of HCW produced depends on the type of HCF and
the specific area within the HCF that generates the waste. Table 2.4 lists the different
types of HCF and the typical HCW produced.
19
Table 2.4 Sources and Categories of Healthcare Waste (HCW)
Sources of Healthcare Waste Categories of Healthcare Waste

Hospital and Medical Centers Infectious Waste
Sharps
Pathological and Anatomical Waste
Pharmaceutical including genotoxic/
cytotoxic/antineoplastic Waste
Chemical Waste
Radioactive Waste
Non-Hazardous or General waste
Clinics and Other HCF Infectious Waste
Emergency Medical Care Services Sharps
Health Centers and Dispensaries Pathological and Anatomical Waste
Obstetrics, Maternity and Lying-in Pharmaceutical including genotoxic/
Clinics cytotoxic/antineoplastic Waste
Out-Patient Clinics Chemical Waste
Dialysis Centers Radioactive Waste
Blood Banks and Blood Collection Centers Non Hazardous or General Waste
Drug Testing Centers
Rehabilitation Establishments and The type of wastes generated varies.
Hospices There are HCFs that generate all the
Transfusion Centers categories, others produce only 2 or 3
Military Medical Services types of HCW
Prison Hospital and Clinics
Physicians Offices/Clinics The volume of HCW generated varies
Dental Clinics based on the type and number of
Dermatology/Skin Clinics clients served.
Alternative Medicines Clinics such as
acupuncture, chiropractic, health spa
Specialized HCF such as convalescing
homes and Differently Abled Person
(DAP) Centers
Related Laboratories and Research General waste

Centers Sharps
Medical and Bio-medical Laboratories Chemical waste
Biotechnology Laboratories and Radioactive materials
Institutions Pathological and Anatomical waste
Medical Research Centers
Blood Banks and Blood Collection Tissue samples packed in formalin or
Services placed in containers with formalin are
Nuclear Medicines Laboratories not considered as infectious waste.
Animal Research Laboratories The tissue sample and the formalin are
classified as pathological and chemical
wastes, respectively.
20
Sources of Healthcare Waste Categories of Healthcare Waste

HCF Mortuary and Autopsy Centers Infectious waste
Sharps
Pathological and Anatomical waste
HCF Pharmaceutical and Chemical General waste,
Department Pharmaceutical and Chemical
wastes (possibly cytotoxic drugs if
chemotherapy treatment are prepared in
the pharmacy)
Ambulances and Emergency Care Infectious Waste
Mobile Services such as mobile X-ray, Sharps
mobile surgical and medical services, General Waste
(including medical mission and health Pharmaceutical Waste
services provided in evacuation centers)
The source often characterizes the composition of HCW being generated. It is

important to determine the source of waste in order to provide the appropriate tools to
be applied. Knowing the types and quantities of HCW generated in a HCF is important
in understanding the hazard and risk that people, community and the environment
maybe facing.
2.4 Impacts of Healthcare Waste to Human Health and the Environment

The inadequate handling and disposal of HCW may lead to transmission of
infectious diseases. The groups most at risk are HCF workers, patients, general public,
the community as well as the environment. Therefore, the framework for management
shall always consider first and foremost patients health and HCF workers safety.
There are many potential hazards associated when dealing or handling HCW such
as physical, chemical and biological hazards as well as psychosocial and ergonomic.
The HCF shall identify all these specific potential environmental and occupational
hazards during handling, storing, treating and disposing of HCW. A team consisting of
trained industrial hygienist, safety officer, infection control, waste management officer
and other HCF professionals can work together to identify potential hazards and ways
to reduce if not to eliminate the hazard.
Apart from the risk to the patients and HCF workers, consideration must be given to
the adverse impacts of HCW to the general public and the environment. In particular,
attention shall be focused on the possible result of unmanaged waste to air, water
and soil, including the community. Minimizing the risk to public health and the
environment will require actions to deal with HCW within the HCF such as proper
waste segregation and minimization so that it does not enter the waste stream requiring
further treatment before disposal.
While the HCF workers are at greater risk of infection through injuries from
contaminated sharps, other workers and waste management operators outside of the HCF
21
are also at risk. Certain infection, however, spread through media or caused by more
resilient agents, may pose a significant risk to the public. For example, the uncontrolled
discharges of wastewater from HCF such as field hospitals treating cholera patients are
potential source of cholera epidemic. However, the use of strong disinfectant shall be
minimized when there are alternatives as these can also chemically pollute the water.
Chemicals used in HCF are potential source of water pollution via the sewer system.
Chemical waste survey is a prerequisite to the development of an effective waste
management program. Any hazardous chemical waste generated shall be dealt with
by a proper chemical waste management system. For safety purposes, always refer to
the Material Safety Data Sheet (MSDS). Substituting chemicals with substance that
have lesser environmental and health impacts is a sound practice. Accidental spillage
within an HCF shall also be dealt with accordingly to minimize impact on human
health and environment.
Pathogenic microorganisms have limited ability to survive in the environment.
This ability is specific to each microorganism and is a function of its resistance to
environmental conditions such as temperature, humidity, ultraviolet irradiation,
availability of organic substrate material, presence of predators, etc.
An example of this is the hepatitis B virus, which is persistent in dry air and can
survive for several weeks on a surface and brief exposure to boiling water. It can also
survive exposure to some antiseptics and to 70% ethanol and remains viable for up to
10 hours at a temperature of 60oC. The Japanese Association for Research on Medical
Waste found out that an infective dose of hepatitis B or C virus can survive for up to
a week in a blood droplet trapped inside a hypodermic needle. In contrast, HIV is
much less resistant. It only survives for no more than 15 minutes when exposed to
70% ethanol and only 3 to 7 days at ambient temperature. It can be inactivated at
56oC temperature.
Bacteria are less resistant than viruses, but less is known about the survival of prions
and agents in degenerative neurological disease (Creutzfeldt-Jakob disease, kuru, etc.)
which seems to be very resistant.
In evaluating the spread or survival of pathogenic microorganisms in the
environment, the role of vectors (e.g. rodents and insects) shall be considered. This
applies to management of HCW both within and outside HCF. Vectors such as rats,
flies, cockroaches, which feed or breed on organic waste, are well known passive
carriers of microbial pathogens; their population may increase dramatically where
there is lack of waste management.
In addition, the public is very sensitive about the visual impact of anatomical waste,
such as, recognizable body parts and fetus. The present culture in the country does not
accept the disposal of anatomical waste inappropriately, such as in a landfill.
22
2.4.1 Person at Risk

All individuals exposed to hazardous HCW are potentially at risk, including those
within the HCF that generate hazardous waste, and those outside these sources who
either handle such waste or are exposed to it as a consequence of careless management.
The main groups of people at risk to potential health hazards associated with HCW are
the following:
HCF staff such as physicians, nurses, healthcare auxiliaries and hospital maintenance
personnel
Personnel and workers providing support and allied services to HCF such as
laundry, waste handling and transporting
Patients in HCF or those receiving home care
Visitors, comforters and caregivers
Persons transporting hazardous HCW to treatment and disposal facilities
Workers and operators of waste treatment and disposal facilities, i.e. sanitary
landfill workers including scavengers
Workers in mortuaries, funeral parlors and autopsy centers
The general public
The hazards associated with scattered, small sources of HCW shall not be
overlooked. Waste from these sources includes those that are generated by home-
based healthcare such as dialysis and that of illegal drug use (usually intravenous).
2.4.2 Exposure to Hazardous Healthcare Waste

Exposure to hazardous HCW can result to disease or injury. The hazardous nature
of HCW may be due to one or more of the following characteristics:
it contains infectious agents

it is genotoxic or cytotoxic
it contains toxic or hazardous chemicals or pharmaceuticals
it is radioactive
it contains sharps
2.4.2.1 Hazards from Pathological/Anatomical Wastes, Infectious Wastes and Sharps

Infectious waste may contain any of a great variety of pathogenic organisms.
Pathogenic organism present in blood and other tissues have already demonstrated
their infectious and virulent characteristics. Pathogens in infectious waste may enter
the human body by a number of routes:
a) through a puncture, abrasion or cut in the skin

b) through the mucous membrane
c) by inhalation
d) by ingestion
23
Table 2.5 Potential Infections Caused by Exposure to Healthcare Wastes,

Causative Organisms and Transmission Vehicle
Type of Infection Examples of Causative Organisms Transmission

Vehicles (Waste
items contaminated
with the following:)
Gastroenteric infection Enterobacteria, e.g. Salmonella, Feces and/or vomit
Shigella spp.; Vibrio cholera; Giardia
lambdia; Clostridium difficile;
helminths
Respiratory infection Mycobacterium tuberculosis; measles Inhaled secretions;
virus; Streptococcus pneumonia, saliva
Severe Acute Respiratory Syndrome
Ocular infection Herpes virus Eye secretions
Genital infection Neisseria gonorrhoeae; herpes virus Genital secretions
Skin infection Streptococcus spp. Pus
Anthrax Bacillus anthracis Skin secretions
Meningitis Neisseria meningitides Cerebrospinal fluid
Acquired Human immunodeficiency virus Blood, sexual
Immunodeficiency secretions, body
syndrome (AIDS) fluids
Haemorrhagic fever Junin, Lassa, Ebola, and Marburg Feces and all body
viruses secretions
Septicaemia Staphylococcus spp. Blood
Bacteraemia Coagulase-negative Staphylococcus Nasal secretion,
spp.; (including Methicillin- skin contact
resistant S. aureus); Enterobacter,
Enterococcus, Klebsiella, and
Streptococcus spp.
Candidaemia Candida albicans Blood
Viral Hepatitis A Hepatitis A virus Feces
Viral Hepatitis B and C Hepatitis B and C viruses Blood and body fluids
Avian influenza H5N1 virus Blood, feces
24
2.4.2.2 Hazards from Chemical and Pharmaceutical Wastes

Although chemical and pharmaceutical wastes may be found in small quantities
in HCF, these substances are hazardous. They may cause intoxication, either by
acute or by chronic exposure and injuries, including burns. Intoxication can result
from absorption of a chemical or pharmaceutical substance through the skin or the
mucous membranes, or from inhalation or ingestion. Injuries to the skin, the eyes
or the mucous membranes of the airways can be caused by contact with flammable,
corrosive or reactive chemicals (e.g. formaldehyde and other volatile substances). The
most common injuries are burns.
Disinfectants are one of the commonly used chemical product in HCF. It is used
in large quantities and is often corrosive. It shall be noted that reactive chemicals
may form highly toxic secondary compounds. Like silver, they may also be priming
bacteria to become antibiotic resistant (McCay et al., 2010).
Obsolete pesticides, stored in leaking containers, can directly or indirectly affect the
health of anyone exposed including the ground water. Poisoning can occur through
direct contact with products, inhalation of vapors, drinking of contaminated water or
eating of contaminated food. Other hazards may include the possibility of fire and
contamination as a result of inadequate disposal such as burning or burying.
Chemical residues discharged into the sewerage system may have adverse effects
on the operation of STP or on the natural ecosystems of receiving waters. Similar
problems may be caused by pharmaceutical residues, which may include antibiotics
and other drugs, heavy metals such as mercury, phenol and derivatives, disinfectants
and antiseptic.
Mercury is highly toxic, especially when metabolized into methyl mercury. It may
be fatal if inhaled and harmful if absorbed through the skin. Around 80% of the inhaled
mercury vapor is absorbed in the blood through lungs. It may cause harmful effects
to the nervous, digestive, respiratory and immune systems. While the use of mercury
in HCF is decreasing, another toxic heavy metal, silver, is being used in even more
applications, including nanotechnology. It is a bactericide and large doses can turn a
persons skin permanently grey (Silver, 2003).
2.4.2.3 Hazards from Genotoxic and Cytotoxic/Antineoplastic Wastes

The severity of hazards for HCF workers assigned to handle or dispose genotoxic
waste is governed by a combination of the substance toxicity itself and the extent and
duration of exposure. Exposure to genotoxic substances in HCF may also occur during
the preparation of or treatment with particular drugs or chemicals. The pathways of
exposure are inhalation of dust or aerosols, absorption through the skin, ingestion as a
result of improper practice, such as mouth pipetting. Exposure may also occur through
contact with the body fluids and secretions of patients undergoing chemotherapy.
The cytotoxicity of many antineoplastic drugs is cell-cycle-specific, targeted
on specific intracellular processes such as DNA synthesis and mitosis. Other
antineoplastics, such as alkylating agents are not phase specific, but cytotoxic at any
25
point in the cell cycle. Many cytotoxic drugs are extremely irritating and have harmful
local effects after direct contact with skin or eyes (Table 2.2). They may also cause
dizziness, nausea, headache or dermatitis. Special care in handling genotoxic waste
is therefore essential; any indiscriminate disposal of such waste will result to health
problems.
2.4.2.4 Hazards from Radioactive Waste

Health effects caused by exposure to radioactive substance or contaminated
materials can range from reddening of the skin and nausea to more serious problems
such as cancer induction and genetic consequences to succeeding generations of the
exposed individual. The handling of high activity sources, e.g. certain sealed and
unsealed radiation sources used in cancer therapy, poses higher health risks such that
adequate protective measures have to be established to minimize these risks.
The health hazards from low activity contaminated wastes may arise from external
and internal exposures from undetected contaminated working environment and
improper handling and storage of radioactive wastes and spent/unused radiation
sources. Both the workers and other staff personnel are at risk to this health hazard.
2.4.2.5 Hazards from Wastewater

Wastewater from HCF is composed of a myriad of materials that pose a hazard to
public health and to the environment. Some of the components of wastewater include
the following:
1. Pathogens
2. Salts
3. Metals
4. Toxic organic compounds
5. Nutrients (nitrogen, phosphorous, potassium)
6. Organic Matter
7. Suspended Solids
8. Acids and Bases
Wastewater may contain pathogens such as bacteria, helminths, protozoa and

viruses that are hazardous if the wastewater is inadequately treated or the untreated
wastewater is used for irrigation of crops. The salt content in wastewater may also
increase soil salinity in the area, rendering the soil useless for agricultural purposes.
Wastewater may also contain trace amounts of metals that can accumulate in the
environment. Toxic organic compounds with carcinogenic, teratogenic and mutagenic
effects may also be present in wastewater from HCF. Pharmaceutical residues or
their by-products present in the wastewater may also contaminate surface water or
ground water, thereby exposing humans through drinking water. Suspended solids in
wastewater are generally non-biodegradable and may lead to clogging of drains if not
treated.
26
Pathogens present in the wastewater can cause waterborne diseases and thus can
survive in the liquid medium. The people in the HCF and the general public are in
danger of contracting these waterborne diseases if the wastewater from the HCF is
not given adequate treatment. Several diseases that can be transmitted via wastewater
include the following:
Capylobacteriosis is an infection of the gastrointestinal tract (severe form of

diarrhoea). This is caused by a bacterium, usually Campylobater jejuni or C. coli.
People are exposed to the bacteria after consuming food or water contaminated
with wastewater or sludge.
Cholera is an acute infection of the intestine caused by the bacterium Vibrio
cholera. It causes severe diarrhoea and vomiting leading to immediate dehydration
and electrolyte imbalance in the body. People become infected after eating food
or drinking water that has been contaminated by feces of infected persons. If
uncontrolled, cholera is known to cause severe and widespread epidemics. Several
countries are issuing travel bans to areas known to be endemic of this disease.
Cryptosporidiosis is caused by the protozoan Cryotosporidium parvum. This
causes acute diarrhoea and is dangerous to people who are immune-compromised
(such as children, HIV/AIDS patients and the elderly) as it can cause death. It is
spread when fecal matter from contaminated individuals enters a water body.
Hepatitis A and Hepatitis E are diseases brought about by viruses. Upon ingestion
of contaminated food or water, the virus infects the liver causing it to be inflamed.
Infection may lead to liver failure causing death. The disease is especially fatal
for pregnant women and the elderly. Both infections are transmitted via fecal-oral
route, often through contaminated water due to inadequate sanitation systems.
Typhoid Fever is a bacterial infection of the intestinal tract and the bloodstream
caused by the bacteria Salmonella typhi and Salmonella paratyphi. The WHO
considers this as a serious public health problem. It causes fevers as high as 40oC
that oscillates within 24 hours, intestinal haemorrhage and delirium. It mostly
affects very young children and adolescents. People become infected by drinking
water that has been contaminated by wastewater containing the bacteria.
27
CHAPTER 3: LAWS, POLICIES, GUIDELINES AND PROTOCOLS
HCF as generators of HCW are responsible for the collection, handling, segregation,
transport, treatment and disposal of the HCW they produce. It is therefore imperative
for them to be cognizant of the existing international agreements, national laws, policies
and specific administrative requirements related to HCWM. These agreements,
national laws, policies and specific administrative requirements will provide them
direction in developing their respective HCWM program.
This chapter provides the salient points of the international agreements, national
laws and policies and technical guidelines that govern HCWM.
3.1 International Agreement

3.1.1 The Montreal Protocol on Substances that Deplete the Ozone Layer (1987)
The Montreal Protocol on Substances that Deplete the Ozone Layer was adopted
in Montreal, Canada on 16 September 1987 and came into force, as agreed, on 1
January 1989. It sets the final objective of the Protocol to eliminate ozone depleting
substances in the environment.
3.1.2 The Basel Convention on the Control of the Trans-boundary Movements of

Hazardous Wastes and Their Disposal (1989)
The Basel Convention concerns the trans-boundary movements of hazardous waste.
The countries that signed the Convention accepted the principle that only legitimate
trans-boundary shipments of hazardous waste are exported from countries that lack
the facilities or expertise to dispose safely of certain waste to other countries that have
both the facilities and expertise.
3.1.3 The United Nations Framework Convention on Climate Change (1992)

The United Nations Framework Convention on Climate Change (UNFCCC) in 1992
included a legally non-binding pledge that by the year 2000 the major industrialized
nations would voluntary reduce their greenhouse gas emissions to 1990 levels.
3.1.4 The Kyoto Protocol to the United Nations Framework Convention on Climate
Change (1997)
The Kyoto Protocol pertains to the reduction of emissions of heat-trapping gases
in the atmosphere. The six gases covered by the Protocol are carbon dioxide (CO2),
methane (CH4), nitrous oxide (N2O), hydrofluorocarbons (HFCs), perfluorocarbons
(PFCs) and sulphur hexafluoride (SF6).Convention on Persistent Organic Pollutants
3.1.5 The Stockholm Convention on Persistent Organic Pollutants (2001)

The Stockholm Convention is a global treaty to protect human health and the
environment from persistent organic pollutants (POPs). Persistent Organic Pollutants are
28
LAWS, POLICIES, GUIDELINES AND PROTOCOLS
chemicals that have the following characteristics: 1) remains unchanged in the

environment for long periods of time; 2) accumulate in the fatty tissue of living
organisms; and 3) are toxic to both humans and wildlife.
3.2 National Laws and Policies
3.2.1 Republic Act No. 4226 Hospital Licensure Act (1965)

The Hospital Licensure Act requires the registration and licensure of all hospitals
in the country and mandates the DOH to provide guidelines for the hospital technical
standards as to personnel, equipment and physical facilities.
3.2.1.1 DOH Administrative Order No. 70-A series of 2002 Revised Rules and
Regulations Governing the Registration, Licensure and Operation of Hospitals and
Other Health Facilities in the Philippines
The Administrative Order includes in the application or renewal of license,
submission of plans and other design requirements under the Code of Sanitation of
the Philippines, National Plumbing Code of the Philippines, Revised Fire Code of the
Philippines and National Building Code of the Philippines. The Manuals on Hospital
Waste Management and Health Facilities Maintenance are also required for submission
for verification by the DOH- Bureau of Health Facilities and Services (BHFS).
3.2.1.2 DOH Administrative Order No. 2005-0029 dated December 12, 2005
Amendment to Administrative Order No. 70-A series of 2002 re: Revised Rules and
Regulations Governing the Registration, Licensure and Operation of Hospitals and
Other Health Facilities in the Philippines
The Administrative Order requires the HCF to submit a Healthcare Waste
Management Plan to BHFS as one of its requirements for the issuance of license to
operate.
3.2.1.3 DOH Administrative Order No. 2007-0027 dated August 22, 2007 Revised
Rules and Regulations Governing the Licensure and Regulation of Clinical
Laboratories in the Philippines
The Administrative Order requires written procedures for the proper disposal of
healthcare waste and other hazardous substances and required written policy guidelines
on bio-safety and bio-security.
3.2.2 Republic Act No. 6969 An Act to Control Substances and Hazardous and
Nuclear Wastes (1990)
The law and its implementing rules and regulations require the registration of waste
generators, waste transporters and operators of toxic and hazardous waste treatment
facilities with the EMB. The waste generators are required to ensure that its hazardous
wastes are properly collected, transported, treated and disposed of to a sanitary landfill.
29
3.2.2.1 DENR Administrative Order No. 36, Series of 2004 Revising DENR
Administrative Order No. 29, Series 1992, to Further Strengthen the Implementation
of Republic Act 6969 and Prescribing the Use of the Procedural Manual
The Procedural Manual requires a comprehensive documentation on the legal
and technical requirements of hazardous waste management. The Manual does not
include provisions regarding the management of nuclear wastes. It is composed of
ten sections that discuss the classification of hazardous wastes, waste generators and
transporters, storage and labelling, Treatment, Storage and Disposal (TSD) facilities,
manifest system, monitoring, prohibited acts and schedule of fees.
3.2.2.2 DOH-DENR Joint Administrative Order No. 02 series of 2005 dated August
24, 2005 entitled Policies and Guidelines on Effective and Proper Handling,
Collection, Transport, Treatment, Storage and Disposal of HCW
The Joint Administrative Order aims to: a) provide guidelines to generators,
transporters and operators/owners of TSD Facilities on proper handling, collection,
transport, storage, treatment and disposal of HCW; b) clarify the jurisdiction, authority
and responsibility of the DENR and DOH with regard to HCWM; and c) harmonize
the efforts of the DENR and the DOH on HCWM.
3.2.2.3 DOH Administrative Order 2007-0014 Guidelines on the Issuance of

Certificate of Product Registration for Equipment or Devices Used for Treating
Sharps, Pathological and Infectious Waste
The Administrative Order requires the manufacturers, importers and distributors,
including generators of HCW that sell and /or use equipment and devices in treating
sharps, pathological and infectious waste to secure a Certificate of Product Registration
(CPR) from DOH through the Bureau of Health Devices and Technology.
3.2.3 Republic Act No. 8749 The Philippine Clean Air Act of 1999
The Act prohibits the incineration of bio-medical wastes effective July 17, 2003.
It promotes the use of state of the art, environmentally sound and safe non-burn
technologies for the handling, treatment, thermal destruction, utilization and disposal
of sorted, unrecycled biomedical and hazardous wastes.
3.2.4 Republic Act No. 9003 Ecological Solid Waste Management Act of 2000
The Act mandates the segregation of solid wastes at the source including households
and institutions like hospitals by using a separate container for each type of waste from
all sources.
30
3.2.5 Republic Act 9275 The Philippine Clean Water Act of 2004
The Act shall pursue a policy of economic growth in a manner consistent with the
protection, preservation and revival of the quality of the countrys fresh, brackish and
marine waters.
3.2.6 Presidential Decree 813 (1975) and Executive Order 927 (1983)
Strengthening the Functions of Laguna Lake Development Authority (LLDA)
The powers and functions of the LLDA were further strengthened to include
environmental protection and jurisdiction over surface waters of the Laguna Lake
basin. Through EO 927, the LLDA is empowered to issue permits for use of surface
waters within Laguna de Bay.
3.2.7 Presidential Decree 856 The Code on Sanitation of the Philippines Chapter
XVII on Sewage Collection and Excreta Disposal (1998)
The law and its IRR on Sewage Collection and Disposal, Excreta Disposal and
Drainage require the approval of the DOH in terms of the following: a) constructions
of any approved type of toilet from every house including community toilets which
may be allowed for a group of small houses of light material or temporary in nature; b)
plans of individual sewage or sewage system and the sub-surface absorption system or
other treatment device; c) location of any toilet or sewage disposal system in relation
to a source of water supply; d) the discharge of untreated effluent of septic tanks and/
or sewage treatment plants to bodies of water; e) manufacture of septic tanks; and f)
method of disposal of sludge from septic tanks or other treatment plants
3.2.7.1 Rules and Regulation Governing the Collection, Handling, Transport,

Treatment and Disposal of Domestic Sludge and Septage, (2004), a Supplement to
the IRR of Chapter XVII on Sewage Collection and Disposal and Excreta Disposal
and Drainage of 1998
The Rules and Regulations require individuals, firms, public and private operators,
owners and administrators engaged in desludging, collection, handling and transport,
treatment and disposal of domestic sewage treatment plants/facilities and septage from
house septic tanks to secure environmental sanitation clearances from DOH.
3.2.7.2 Chapter XVIII of Presidential Decree 856 The Code on Sanitation of the
Philippines on Refuse Disposal (1998)
The law and its IRR on Refuse Disposal require cities and municipalities to provide
an adequate and efficient system of collecting, transporting and disposing refuse in
their areas of jurisdiction. It also requires occupants of buildings, institutions such as
hospitals and residences to provide sufficient number of receptacles for refuse.
31
3.2.7.3 Operation Manual on the Rules and Regulations Governing Domestic Sludge
and Septage, June 2008
The Manual provides detailed procedures and forms needed to comply with the
IRR Governing Collection, Handling, Transport, Treatment and Disposal of Domestic
Sludge and Septage. It is designed to guide private and public service providers as
well as government regulators to effective sludge and septage management program
in the country.
3.2.7.4 Administrative Order 2010-0033 Revised Implementing Rules and

Regulations of PD 856 Code on Sanitation of the Philippines Chapter XXI Disposal of
Dead Persons December 2010
The Administrative Order has placed a new restriction on open viewing of remains
if the individual died of certain dangerous communicable diseases. It explicitly says:
The remains shall be placed in a plastic cadaver bag or other durable airtight container
at the point of death and a biohazard tag attached, provided, that, this container shall
not be opened for viewing or any other purpose prior to burial or cremation.
3.2.8 Presidential Decree No. 984 Providing for the Revision of Republic Act No.
3931, Commonly known as the Pollution Control Law, and for Other Purposes
(1976)
The Pollution Control Law is the primary legislation that governs discharges of
potentially polluting substances to air and water. It provides the basis for the DENR
regulations on water pollution through its IRR, DENR Administrative Order Nos. 34
and 35. The IRR for air emissions was initially set by DENR Administrative Order
No. 14, but was later replaced by the Clean Air Act of 1999 (RA 8749).
3.2.8.1 DENR Administrative Order No. 34 Series 1990 Revised Water Usage and
Classification/Water Quality Criteria Amending Section Nos. 68 and 69, Chapter III
of the 1978 National Pollution Control Commission (NPCC now EMB) Rules and
Regulations
The Administrative Order classified the bodies of water according to its particular
designated use or uses and does not preclude use of the water for other purposes that
are lower in classification provided that such use does not prejudice quality required
for such waters.
3.2.8.2 DENR Administrative Order No. 35, Series 1990, Effluent Regulations
The Administrative Order lists the effluent regulations for the different levels of
pollutants according to its water category/class.
3.2.8.3 DENR Administrative Order No. 26, Series 1992, Amending Memorandum
Circular No. 02, Series of 1981: Appointment/Designation of Pollution Control
Officers
32
The Administrative Order requires the appointment/designation of Pollution

Control Officer (PCO) and lists the qualifications, reporting requirements and duties
and responsibilities of accredited PCOs.
3.2.9 Presidential Decree No. 1586 Environmental Impact Statement (EIS)

System (1978)
The EIS System requires projects, like construction of new hospital buildings or
expansion of existing hospitals, to secure an Environmental Compliance Commitment
(formerly Environmental Compliance) Certificate (ECC) prior to construction and
operation of the facility. An ECC is required for the installation and operation of
HCW treatment systems like pyrolysis, autoclave, microwave and other treatment
technology including landfills.
3.2.10 Executive Order No. 301 (2004) Establishing a Green Procurement

Program for All Departments, Bureau, Offices and Agencies of the Executive
Branch of Government
The Green Procurement Program was implemented in all government offices
that aims to a) promote the culture of making environmentally-informed decisions
in government, especially in the purchases and use of different products; b) include
environmental criteria in public tenders, whenever possible and practicable; c)
establish the specifications and requirements for products or services to be considered
environmentally advantageous; and d) develop incentive programs for suppliers of
environmentally advantageous products or services.
3.2.11 DOH Administrative Order No. 2008-0021 dated July 30, 2008 Gradual
Phase out of Mercury in all Philippine Healthcare Facilities and Institutions
The Administrative Order requires all HCF to gradually phase-out the use of
mercury containing devices and equipment. The initial targets of the phase-out are
mercury thermometers and sphygmomanometers in the healthcare facility.
3.2.11.1 Department Memorandum No. 2011-0145, Guidelines for the Temporary

Storage of Mercury Wastes in HCF in Accordance with AO No. 0021 s. 2008 on the
Gradual Phase-out of Mercury in All Philippine Healthcare Facilities and Institutions
The Department Memorandum provides the detailed guidelines on the Temporary
Storage of Mercury Containing Devices and the Management of Mercury Spills to
enhance the patient safety measures in HCF, protect healthcare workers from potential
hazards from mercury exposures; and to minimize the accumulation of mercury in the
environment.
33
3.2.12 DOH Administrative Order No. 2008-0023 dated July 30, 2008 National
Policy on Patient Safety
The Administrative Order requires the establishment and maintenance of a culture
of patient safety in the HCF as the responsibility of its leadership. As such, HCF
shall ensure that an enabling mechanism/strategy is in place to ensure patient safety.
The key priority areas in patient safety include but are not limited to proper patient
identification, assurance of blood safety, safe clinical and surgical procedures, provision
and maintenance of safe quality drugs and technology, strengthening infection control
standards, maintenance of the environment of care standards and energy and waste
management standards.
3.2.13 DOH Healthcare Waste Management Manual in 2004 (Revising the 1997
Hospital Waste Management Manual)
The Second Edition Healthcare Waste Management Manual aims to achieve the
following: a) improvement of regulatory compliance; b) protection of human health
by reducing the exposure of workers, patients, watchers, and entire community to
hazardous HCW in the work environment; c) enhancement of community relations
by demonstrating a commitment to environmental protection; d) gain of economic
benefits resulting from pollution prevention, products that reduce and recycle waste;
e) avoidance of long-term liability; and f) increase in workers morale resulting from
a healthier and safer work environment.
3.2.14 Philhealth Benchbook for Quality Assurance in Healthcare (2006)

The Philhealth Benchbook included healthcare waste management as one of its
parameters in the quality assurance of healthcare.
3.2.15 BFAD Memorandum Circular No. 22 Series of 1994, Inventory, Proper

Disposal and/or Destruction of Used Vials or Bottles and BFAD Bureau Circular
No. 16 Series of 1999: Amending BFAD MC No. 22 dated September 8, 1994,
Regarding Inventory, Proper Disposal and/or Destruction of Used Vials or Bottles
These circulars are released to prevent the proliferation of adulterated, misbranded
and counterfeit drugs brought about by the recycling of used pharmaceutical bottles
and vials. It contains the guidelines on the proper inventory and destruction of bottles
and vials.
Table 3.1 provides online links to the full text of the different legislations, policies
and technical guidelines mentioned in this chapter. One can access these by logging
on to the World Wide Web and inputting the links to the internet server.
34
Table 3.1 On-Line Links to the Legislation, Policies and Guidelines
POLICIES LINKS
3.1 INTERNATIONAL AGREEMENTS
1.) The Montreal Protocol on Substances that http://ozone.unep.org/Ratification_
Deplete the Ozone Layer (1987) status/montreal_protocol.shtml
2.) The Basel convention on the Control of http://www.basel.int/text/documents.
Transboundary Movements of Hazardous html
Wastes and Their Disposal (1989)
3.) The United Nations Framework http://unfccc.int/2860.php
Convention on Climate Change (1992)
4.) The Kyoto Protocol to the United Nations http://unfccc.int/resource/docs/convkp/
Framework Convention on Climate kpeng.html
Change (1997)
5.) The Stockholm Convention on Persistent http://www.pops.int/documents/
Organic Pollutants (2001) convtext/convtext_en.pdf
3.2 NATIONAL LAWS AND POLICIES
3.2.1 Republic Acts
1.) Republic Act 4226 Hospital Licensure http://www.doh.gov.ph/ra/ra4226
Act (1965)
2.) Republic Act 6969 An Act to Control http://cdmdna.emb.gov.ph/elaws/
Toxic Substances and Hazardous and Images/RA%206969.pdf
3.) Republic Act 8749 The Philippine Clean http://cdmdna.emb.gov.ph/elaws/
Air Act (1999) Images/RA%208749.pdf
4.) Republic Act 9003 Ecological Solid http://cdmdna.emb.gov.ph/elaws/
Waste Management Act (2000) Images/RA%209003.pdf
5.) Republic Act 9275 The Philippine Clean http://cdmdna.emb.gov.ph/elaws/
Water Act (2004) Images/RA%209275.pdf
3.2.2 Presidential Decrees
1.) Presidential Decree 856 The Code of http://www.lawphil.net/statutes/
Sanitation of the PhilippinesChapter presdecs/pd1975/pd_856_1975.html
XVII on Sewage Collection and Excreta
Disposal (1976)
2.) Presidential Decree 984 Providing for http://www.lawphil.net/statutes/
the Revision of Republic Act 3931, presdecs/pd1976/pd_984_1976.html
Commonly known as the Pollution
Control Law, and for Other Purposes
3.) Presidential Decree 1586 Environmental http://cdmdna.emb.gov.ph/elaws/
Impact Statement System (1978) Images/PD%201586.pdf
4.) Presidential Decree 813 & Executive http://www.llda.gov.ph/docs/laws/
Order 927 Further Defining Certain eo927.pdf
Functions and Powers of the Laguna
Development Authority (1983)
35
POLICIES LINKS
3.2.3 Executive Orders
1.) Executive Order 301 Establishing a http://elibrary.judiciary.gov.ph/index10.
Green Procurement Program for all php?doctype=Executive%20Orders&do
Departments, Bureaus, Offices, and cid=5d3ffd0d08f72df23d314ca4b4f606
Agencies of the Executive Branch of the 15455a487b23672
Government
3.2.4 Administrative Orders
1.) DENR Administrative Order 34- http://cdmdna.emb.gov.ph/elaws/
1990 Revised Water Usage and Images/DAO%201990-34.pdf
Classification/Water Quality Criteria
Amending Section Nos 68 and 69,
Chapter III of the 1978 NPCC Rules and
Regulations (1990)
2.) DENR Administrative Order 35-1990 http://cdmdna.emb.gov.ph/elaws/
Effluent Regulations (1990) Images/DAO%201990-35.pdf
3.) DOH Administrative Order 70-A Series http://home.doh.gov.ph/ao/ao70A-02.
2002 Revised Rules and Regulations pdf
Governing the Registration, Licensure,
And Operation of Hospitals and Other
Health Facilities in the Philippines
4.) DENR Administrative Order No. 26, http://www.denr.gov.ph/policy/1992/
Series 1992, Amending Memorandum DENR_DAO_92-26.pdf
Circular No. 02, Series of 1981:
Appointment/Designation of Pollution
Control Officers
5.) DENR Administrative Order 36-2004 http://cdmdna.emb.gov.ph/elaws/
Revising DENR Administrative Images/DAO%202004-36.pdf
Order No. 29 Series 1992, to Further
Strengthen the Implementation of
Republic Act 6969 and Prescribing the
Use of the Procedural Manual (2004)
6.) DOH-DENR Joint Administrative http://denr.gov.ph/policy/2005/dao/
Order 02-2005 Policies and Guidelines joint_dao2005-02.pdf
on Effective and Proper Handling,
Collection, Transport, Treatment,
Storage, and Disposal of HCW (August
24, 2005)
7.) DOH Administrative Order 2005- http://home.doh.gov.ph/ao/ao2005-
0029 Amendment to Administrative 0029.pdf
Order No. 147 s. 2004: Amending
Administrative Order No. 70-A Series of
2002 re: Revised Rules and Regulations
Governing the Registration, Licensure
and Operation of Hospitals and Other
Health Facilities in the Philippines
36
POLICIES LINKS
3.2.4 Administrative Orders Continued
0014 Guidelines on the Issuance of 0014.pdf
Certificate of Product Registration
for Equipment or Devices Used for
Treating Sharps, Pathological and
Infectious Waste
0027 Revised Rules and Regulations 0027.pdf
Governing the Licensure and
Regulation of Clinical Laboratories in
the Philippines
10.) DOH Administrative Order 2008-21 http://www.gefmedwaste.org/
Gradual Phase-Out of Mercury in All downloads/AO%2021.pdf
Philippine Healthcare Facilities and
Institutions (July 30, 2008)
11.) DOH Administrative Order 2008-23 http://home.doh.gov.ph/ao/ao2008-
National Policy on Patient Safety 0023.pdf
(July 30, 2008)
0033 Revised Implementing Rules 0033.pdf
and Regulations of PD 856 Code on
Sanitation of the Philippines
13.) DOH Department Memorandum 2011- http://home.doh.gov.ph/dm/dm2011-
0145 Guidelines for the Temporary 0145.pdf
Storage of Mercury Wastes in HCF in
Accordance with AO No. 0021 s. 2008
on the Gradual Phase-out of Mercury in
All Philippine Healthcare Facilities and
Institutions
3.2.5 Guidelines
1.) Healthcare Waste Management http://www.pcij.org/blog/wpdocs/
Manual-- Revising the 1997 Hospital hcwm.pdf
Waste Management Manual(2004)
2.) Philippine Health Insurance http://www.philhealth.gov.ph/providers/
Corporation Benchbook for download/bnchbk_scoring_guide.pdf
QualityAssurance in Health Care
(2001)
3.) Operations Manual on the Rules and http://www.waterlinks.org/library/
Regulations Governing Domestic septage-management/operations-
Sludge and Septage (2008) manual-governing-domestic-sludge-
and-septage
37
POLICIES LINKS
3.2.5 Guidelines
1.) BFAD Memorandum Circular No. http://www.fda.gov.ph/MC/mc%20
22 Series of 1994: Inventory, Proper 22%201994.pdf
Disposal, and/or Destruction of Used
Vials or Bottles
2.) BFAD Bureau Circular No. 16 Series http://www.fda.gov.ph/BC/bc%20
of 1999: Amending BFAD MC #22 16%20s%201999.pdf
dated September 8, 1994, Regarding
Inventory, Proper Disposal, and/or
Destruction of Used Vials or Bottles
38
PART II
HEALTHCARE WASTE
MANAGEMENT
SYSTEM
40
HEALTHCARE WASTE MINIMIZATION
CHAPTER 4: HEALTHCARE WASTE MINIMIZATION

The HCW generated within a HCF follows an appropriate and well identified
stream from point of generation until their final disposal, that is composed of several
steps that includes waste generation, segregation, collection, transportation (on-site
and off-site), storage, treatment and disposal.
To illustrate, Figure 4.1 summarizes the HCW handling the flow of waste from
point of generation up to its final disposition.
STEP LOCATION HEALTHCARE WASTE KEY POINTS

HANDLING
0 Procurement Waste Minimization Green Procurement Policy,
stock management, Life Cycle
Analysis (LCA), resource
development (3Rs)
1 At Source, Generation Color coded garbage
clinical wards, bins/liners. Proper waste
offices, segregation
2 laboratories, Segregation at One of the most important
and all source step to reduce risks and
HCF units amount of hazardous waste
generated
Collection + On- PPEs, dedicated collection
3 site Transport bins (color-coded), easy to
wash and dedicated trolleys
Within the Central HCW storage,
4 HCF On-site Storage lockable, easy to clean,
compliant with standards
Adequate space, availability
5 of acceptable treatment/
On-site disposal methods within the
Treatment/ HCF
6 disposal DENR accredited TSD,
appropriate vehicle, HCF
is informed about final
Off-site Transport destination
DENR accredited TSD,
7 Outside the HCF sanitary Landfill. Appropriate
Off-site vehicle and duly signed
Treatment/ consignment note. Ensure
disposal proper waste treatment and
disposal
Figure 4.1 Healthcare Waste Handling
Source: Adapted from WHO Guidance Manual for the Preparation of National
Healthcare Waste Management Plans in Sub-Saharan Countries
41
This chapter specifically discusses the initial phase in HCW handling (Step 0). The
major tool of Waste Minimization is Resource Development, which pertains to the
3Rs: Reuse, Recycle and Recover.
The underlying principle of Waste Minimization is rooted in the Hierarchy of
Controls, which was already discussed thoroughly in Chapter 1 of this manual. Figure
1.2 in Chapter 1 showed that prevention is very important, thus before producing
waste; the HCF shall investigate whether the amount of waste to be generated from
the daily operation of the HCF could be minimized in order to reduce the efforts in
subsequent handling, treatment and disposal operations. Waste minimization can be
done in two points of the healthcare waste handling. First, waste can be minimized
during the procurement procedure of materials needed by the HCF (Step 0). By
purchasing environmentally friendly products, one can already minimize the amount
of waste that is to be generated. Second, waste can be minimized through the process
of segregation. In this process, the principle of the 3 Rs is applied, thus, segregation
effectively reduces the amount of waste to be treated or collected.
There is a correlation between waste minimization and environmental management
system (EMS) which provides a framework for managing an organizations environment
impacts. This program is being spearheaded by the Environment Management Bureau
(EMB) of the Department of Environment and Natural Resources (DENR).
All the elements involved and illustrated in Figure 4.1 will be further discussed in
succeeding topics.
4.1 Waste Minimization

The quantity of HCW generated shall always be minimized and precautions must
be taken during their handling. The critical point in minimizing waste starts from
the planning stage of the preparation of the Annual Procurement Plan (APP), which
includes the list of items required for HCF activities.
The management of HCF must adopt the following strategies to implement waste
minimization:
Establish an updated database for the waste generation rates, current hazardous
waste management strategies and current waste management costs
Institutionalize waste minimization and sustain the program in the long run
Have a written policy with established vision and mission to implement Waste
Minimization Program (WMP)
Be aware of their specific role in HCWM and be properly trained in waste
minimization
Adopt the Green Procurement Policy (GPP) pursuant to Executive Order 301,
series of 2009.
42
Waste Minimization as the initial step aims at reducing as much as possible the
amount or quantity of HCW that will be produced by setting up an efficient purchasing
policy and having good stock management.
If waste minimization is to be undertaken by the HCF, it is important to develop a
good baseline data of the amount of waste generated prior to implementation of the
waste minimization program. HCW generation data from the various units of the HCF
shall be properly recorded on a chart with the amount of waste displayed in descending
order. This method can be used to determine the highest waste generating areas where
the minimization strategies shall first be initiated. This information shall be displayed
and communicated throughout the HCF.
The waste minimization strategy shall be formally approved in writing by top
management within the HCF as a demonstration of their support and commitment to
the program.
4.2 Principles of Waste Minimization

Waste minimization is beneficial not just to the waste-receiving environment but
to the waste generators also. The cost for both the purchase of goods and waste
treatment and disposal are reduced and the liabilities associated with the disposal of
HCW is lessened. The extent to which a hazardous waste minimization program is
implemented depends upon the HCFs particular operations and procedures.
The principle of waste minimization is illustrated by the waste management
hierarchy, applying the following techniques:
Green Procurement refers to waste prevention and reduction at source

Resource Development (3Rs) refers to reuse, recycling and recovery
End of Pipe refers to treatment and disposal
These techniques, along with the different measures that make them possible, are
discussed in the succeeding sections.
4.2.1 Green Procurement: Waste Prevention and Reduction at Source

Waste is minimized even before its generation in a HCF through proper procurement
planning with the adoption of the Green Procurement Policy where items/goods to be
purchased will have minimum packaging and will generate less hazardous waste; will
utilize proper inventory of stocks and conduct Life Cycle Analysis for equipment.
In the initial phase, the HCF Administrators in order to reduce the generation of
waste can adopt as one measure, the GPP which refers to the principle of purchasing
products and services that are least damaging in terms of environmental impact,
addressing the issue of HCW at the source is more economically and environmentally
beneficial than looking into the perennial issue of waste management disposal.
43
4.2.1.1 Waste Prevention through the Adoption of Green Procurement Policy Pursuant
to Executive Order 2004-31
A HCF, as part of its green procurement strategy, can consider some of the following
approaches:
Supplier Focus (through the supplier registration form with emphasis on

environmental performance of supplier)
Product and Service Focus (including environmental specifications)
Life Cycle Analysis (internal analyses, or utilizing LCA completed by external
groups)
In effect, the Green Procurement Policy urges a HCF to buy less polluting products
from a less polluting supplier. The objectives of such procurement are:
Creating awareness of environmental impact

Developing guidelines for green procurement
Rethinking material requirements and consumption
Reducing the use of hazardous materials, improving energy efficiency of
purchased materials
Using recycled materials and recycling of waste
Production of goods is required to have less environmental impact to avoid

environmental contamination and harm to human health. Measures must be taken to
prevent hazardous substances from being released when products are used, scrapped
or disposed of to ensure that the production of goods does not contain any substance
that may cause damage to the environment or human health and to promote greener
design and disposal activities at any HCF.
Thus, a HCF will only procure goods from companies that fulfilled the following
requirements:
Producing goods that do not contain any substance included in the EMB-DENR
list of banned substances; and
Establishing a complete elimination program for banned substances; and
making a commitment to sustain the program.
Under these guidelines, a HCF can introduce measures to increase the utilization
of recycled materials and the purchase of more environmental friendly equipment (for
instance, computers with a high Energy-Star rating or computers with higher percentage
of recyclable materials). The gradual shifting to energy efficient technology is one
method to reduce energy consumption and can be achieved through green procurement
guidelines.
In order to ensure the effective implementation of these guidelines, a HCF can
carefully consider its existing procurement practices in order to evaluate where the major
44
environmental impacts lie. Methods can then be sought to integrate environmental

considerations into its purchasing practices. These can be designed to fit with existing
procurement methods, and to act as a support tool for the purchasing staff. The policy,
procedures and practices shall not be designed to prohibit the purchase of any goods
but merely to favour goods that are environmentally friendly. Other factors such as
the quality, price, delivery time, etc. still remain paramount in purchasing decisions.
4.2.1.2 Waste Reduction at Source through Proper Segregation of Waste

Segregation is an important step in HCWM. There are several reasons why it is
needed:
Segregation minimizes the amount of waste that needs to be managed as

hazardous waste (since mixing non-hazardous waste with hazardous waste
renders the combined waste as hazardous);
Segregation facilitates waste minimization by generating a solid waste stream
which can be easily, safely and cost-effectively managed through recycling or
composting;
Segregation reduces the amount of hazardous substances released to the
environment through disposal of general waste (i.e. by removing mercury from
general waste);
Segregation makes it easier to conduct assessment of the quantity and
composition of different waste streams thereby allowing a HCF to obtain
baseline data, identify options, determine waste management costs and evaluate
the effectiveness of waste minimization strategies.
Further discussion of this topic can be found in Chapter 5 of this Manual.
4.2.2 Resource Development (The 3 Rs)

Another principle applied in waste minimization is Resource Development referring
to Safe Re-use, Recycle and Recovery programs.
4.2.2.1 Safe Re-use

Re-use is not only finding another use for a product but, more importantly, reusing
the product over and over again for a given function as intended. Promoting re-use
entails the selection of reusable rather than disposable products whenever possible.
Re-use will also entail setting reliable standards for disinfection and sterilization of
equipment and materials for use.
In general, the purchase and use of non-disposable items in a HCF shall be
encouraged as much as possible. When considering reuse it is important to make a
distinction between different types of products:
Non-medical supplies, particularly disposable items used in catering services,

shall be avoided
Medical devices that pose no cross-infection risk, e.g. blood pressure meters
Medical devices specifically designed for reuse, e.g. surgical instruments
45
Single use device such as syringes and hypodermic needles must not be reused because
of the risk of cross-infection. Where there is an option to purchase a reusable device
or to purchase a single use device, the former is always preferable.
Safe re-use may involve a combination or all of the sterilization methods, such as
cleaning, reconditioning, autoclaving, disinfection and decontamination.
4.2.2.2 Recycling and Recovery

Recycling involves processing of used materials (waste) into new
products to prevent loss of potentially useful materials, reduce the
consumption of fresh raw materials, reduce energy usage, reduce
air pollution and water pollution (from land filling) by reducing the
need for conventional waste disposal and lower greenhouse gas
emissions as compared to virgin production.
Recyclable materials include many kinds of glass, paper, metal, plastics, textiles and
electronics. Although similar in effect, the composting or other re-use of biodegradable
waste, such as food or garden waste, is not typically considered recycling. Materials
to be recycled are brought to a collection center or picked up from the curb side, then
sorted, cleaned and reprocessed into new materials bound for manufacturing.
Through the use of the Life Cycle Analysis tool (LCA), which is discussed in
Chapter 8 of this Manual, the administrators of the HCF will be able to decide which
product or service will be most suitable or applicable for its operations. LCA is a
compilation and evaluation of the input, output and potential environmental impacts
of a product or system throughout its life cycle.
LCA is the assessment of environmental impacts associated with a product, process
or service throughout its life cycle, form the extraction of the raw materials through to
processing, transport, use, re-use, recycling or disposal. It is also known as the cradle-
to-grave analysis.
The goal of LCA is to compare the full range of environmental damages assignable
to products and services. Following this assessment, businesses can identify the most
effective improvement that they can make in terms of environmental impacts and use
of resources.
Benefits:
Identify the most efficient and cost effective options for increasing the
environmental performance of a product or service.
Identify opportunities for efficiency improvement
LCA can also be used for comparing the environmental credentials of similar
products and services to be able to choose the least burdensome ones. For each stage,
the impact is measured in terms of resource use and environmental impacts.
46
Example:
To determine whether beverage packaging made of glass is more or less burdensome
than plastic bottles, all life cycle phases for both options shall therefore be investigated.
For glass bottles, the phases would include the mining of glass minerals, bottle
production, bottling, transport, and final disposal.
For plastic bottles the phases are raw oil production, oil refining, polymer
production, bottle production, bottling, transports, and final disposal.
In a strict sense, recycling of a material would produce a fresh supply of the same
material. For example, used office paper would be converted into new office paper
or used foamed polystyrene would be converted into new polystyrene. However, this
is often difficult or too expensive (compared with producing the same product from
raw materials or other sources), so recycling of many products or materials involve
their re-use in producing different materials (e.g. paperboard) instead. Another form
of recycling is the salvage of certain materials from complex products, either due to
their intrinsic value (e.g. lead from car batteries, gold from computer components)
or due to their hazardous nature (e.g. removal and re-use of mercury from various
items. However, this practice is now banned because of the hazards involved during
its recovery).
The recovery of waste is defined in two ways. Most simply, recovery refers to
energy recovery, whereby waste is converted to fuel for generating electricity or for
direct heating of premises. Alternatively, waste recovery is a term used to encompass
three sub-sets of waste recovery: recycling, composting and energy recovery.
In determining the economic viability of recycling it is important to take account of
the cost of alternative disposal methods and not just the cost of recycling process and
the value of the reclaimed materials.
47
4.2.3 End of Pipe: Treatment and Disposal

Waste treatment refers to the process of changing the biological and chemical
character of the waste to minimize its potential to cause harm.
Waste disposal refers to discharge, deposit, placing or release of any health care
waste into or on any air land or water.
One common strategy used is composting waste such as food discards, kitchen
waste, cardboard and yard waste. Some HCF in other countries have also successfully
composted placenta waste. Sufficient land space for on-site composting, adequately
distant from patient care and public access area, would be needed. Food scraps can
provide most of the nitrogen, while bulking agents commonly found in HCF such as
cardboard and wooden chips could provide carbon. Composting techniques range
from simple un-aerated static piles to aerated windrows to vermin-composting. The
resulting rich compost can be sold or donated to local farmers and gardeners or can be
used for plants around HCF grounds. Further illustration and discussion of this topic
can be found in Chapter 6 of this Manual.
4.3 Administrative Control Measures

Green Procurement, 3 Rs and End of Pipe solutions can be achieved through,
among others, administrative control measures such as:
Adopting Environmental Management System (EMS)

Systemized use of product first in, first out (FIFO) or first to expire, first out
(FEFO) for chemical and pharmaceutical products
Monitoring of chemical flows within the healthy facility from receipt as raw
materials to disposal as hazardous waste
Elimination of medical supplies and equipment containing hazardous chemicals
like mercury
Using less hazardous method in cleaning such as steam disinfection instead of
chemical disinfection
Checking the expiry date of all products at the time of delivery and based on its
optimum consumption rate
Environmental Management System (EMS) refers to the management of an

organizations environmental programs in a comprehensive, systematic, planned and
documented manner. It includes the organizational structure, planning and resources
for developing, implementing and maintaining a policy for environmental protection.
This is further discussed in Chapter 8: Administrative Requirement.
48
4.4 Benefits of Waste Minimization

Institutionalization of Waste Minimization Program will enhance the HCF as to:

Financial
Cost savings through effective waste management and more efficient use of
natural resources (electricity, water, gas and fuels).
Additional income generated from sale of recyclable waste.
Fines and penalties are avoided in meeting environmental legislation by
identifying environmental risks and addressing weaknesses.
Reduction of insurance and health costs by demonstrating better risk management.
Operational and Internal
Improved overall performance and efficiency

Compliance with the PHIC Benchbook Performance Indicator
External
Better public perception of the HCF

Reduction of the adverse environmental impact (i.e. land, air and water pollution)
Promoting environmental sustainability
49
Chapter 5: Segregation, Collection, Storage and

Transport of Healthcare Waste
The management of HCF has a duty to ensure that all HCW are managed properly
and in a safe manner. Under the Basel Convention (The Basel Convention on the
Control of the Trans-boundary Movements of Hazardous Waste and their Disposal),
the Stockholm Convention on Persistent Organic Pollutants and Republic Act 6969
(An Act to Control Toxic Substances and Hazardous and Nuclear Wastes), HCW
is classified as hazardous. This chapter describes the proper segregation of HCW
at the point of generation, collection, storage and transport for treatment prior to
its final disposal. Segregation is the key to effective waste management and only
implementation of proper waste management can ensure all HCW will be treated
according to the hazards.
General Principles:
HCW must be segregated, collected, stored and transported in a safe manner
considering the risk and occupational safety and in accordance with existing laws,
policies and guidelines.
The HCF must have a Waste Management Officer (WMO) who will be responsible
for HCWM.
Hazardous and general waste must not be mixed during collection, transport and
storage.
Staff must be well-trained on the risk and safety procedures on handling waste.
Appropriate labelling, signage, route and segregation system must be established.
Plastic liners preferably containing full of waste must be sealed when transported
from waste generating source to the waste storage area.
The storage area must be designed based on the volume of waste generated by
the HCF and must be provided with compartments for general, hazardous and
recyclable wastes.
A separate storage area for phase-out mercury containing devices and products
must be provided (Administrative Order 2008-21 Regarding the Phase-Out of
Mercury Devices in HCF and Department Memorandum 2011-0145 on temporary
storage of mercury wastes).
The HCF must register as waste generator with the DENR and secure a DENR
waste generator identification number.
5.1 Waste Segregation

The effective management of HCW considers the basic elements of waste
minimization, segregation and proper identification of the waste. Appropriate handling,
treatment and disposal of waste by type reduce costs and do much to protect public
health. Segregation at source shall always be the responsibility of the waste generator.
50
SEGREGATION, COLLECTION, STORAGE AND TRANSPORT OF HEALTHCARE WASTE
Segregation shall take place as close as possible to where the waste is generated and
shall be maintained in storage areas and during transport.
Segregation is the process of separating different types of waste at the point of
generation until its final disposal. Appropriate resource recovery and recycling
technique can be applied to each separate waste stream. Moreover, the amount of
hazardous waste that needs to be treated will be minimized or reduced subsequently
prolonging the operational life of the disposal facility and may gain benefit in terms of
conservation of resources.
Segregation is the separation of the entire waste generated from the HCF according
to the specific treatment and disposal requirements. Depending on the type of facility,
10% - 25% of waste generated by HCF is considered hazardous. On the other hand,
the hazardous waste produced by HCFs in the Philippines is around 30% (ADB, 2003).
This only shows that the HCWM system in the country must be improved.
Hazardous wastes generated require special treatment methods for the safety of
HCF workers, patients, visitors and the general public. Segregating the hazardous
waste will significantly reduce the waste management costs.
Segregation of waste must be strictly implemented at source. It must be applied
from the point of generation, during collection, transport, storage and at the treatment
site prior to final disposal.
Hazardous waste shall be placed in clearly marked waste bins with plastic liners that
meet the standard thickness of 0.009mm and are appropriately labelled for the type and
weight of the waste. Sharps shall be placed in puncture-proof containers. Hazardous
chemical liquid waste can be placed in amber disposal bottles or its equivalent.
To improve segregation efficiency and minimize incorrect use of bins, proper
placement, labelling of waste bins and use of color-coded plastic liner must be strictly
implemented. Waste bins with yellow liners for infectious wastes shall be placed in,
but not limited to, the following areas: Emergency Room, Out Patient Department,
Laboratory, Radiology, Dental and Isolation Rooms, Infectious Wards, Dialysis and
Nurses Stations.
5.1.1 Labelling, Marking and Color-Coding of Waste Bins and Plastic Liners
The system of segregation must be enforced throughout the country. The purpose
of color coding is to make it easier for HCF workers to put the waste into correct bins
and maintain segregation during collection, storage, transport, treatment and disposal.
The color coding scheme for HCW as shown in Table 5.1 shall be adopted.
51
Table5.1
Table 5.1Labelling,
Labelling,Markings
Markings and
and Color-Coding
Color-Coding of Plastic
of Plastic Liners
Liners and and
BinsBins
PLASTIC LINERS BINS
TYPE OF
MARKINGS AND SPECIFICA- MARKINGS AND SPECIFI-
WASTE
LABELLING TION LABELLING CATION
INFECTIOUS Properly labelled Yellow plastic Properly labelled Strong leak
WASTE INFECTIOUS that can INFECTIOUS proof bin with
WASTE withstand And with cover
Tag indicating source autoclaving Biohazard Symbol
and weight of waste Thickness: Size varies
generated, date of 0.009mm depending on
collection Sample sizes: XL the volume of
Biohazard symbol size waste
optional 39cm x 39cm x
95cm
Size varies
depending on the
volume of waste
PATHOLOGI- Properly labelled Yellow Properly labelled Strong leak
CAL AND PATHOLOGICAL/ Thickness: PATHOLOGICAL/ proof bin with
ANATOMICAL ANATOMICAL 0.009mm ANATOMICAL cover
WASTE WASTE Sample sizes: XL WASTE
Tag indicating source, size And with Size varies
weight of waste 39cm x 39cm x Biohazard Symbol depending on
generated, date of 95cm the volume of
collection Size varies waste
Biohazard symbol depending on the
optional volume of waste
SHARPS Not applicable Not applicable Properly labelled Puncture-
SHARPS proof
Source and weight of container with
waste generated, date wide mouth
of collection and cover
Biohazard symbol
PHARMACEU- Properly labelled Yellow with Properly labelled Strong leak
TICAL PHARMACEUTICAL black band PHARMACEUTI- proof
WASTE Thickness: CAL WASTE for container with
Tag indicating source, 0.009mm expired drugs and for cover
weight of waste Sample sizes: XL containers
generated, date of size CYTOTOXIC Size varies
collection 39cm x 39cm x WASTE for depending on
95cm cytotoxic, genotoxic the volume of
Size varies and antineoplastic waste
depending on the waste
volume of waste
52
52
PLASTIC LINERS BINS

TYPE OF MARKINGS MARKINGS
SPECIFICA- SPECIFI-
WASTE AND AND
TION CATION
LABELLING LABELLINGS
CHEMICAL Properly labelled Yellow with Properly labelled For liquid
WASTE CHEMICAL WASTE black band CHEMICAL chemical
WASTE waste:
Tag indicating source, Thickness: Disposal
weight of waste 0.009mm bottle that is
generated, date of Sample sizes: XL made of
collection size amber-colored
39cm x 39cm x glass, with at
95cm least 4L
Size varies capacity that
depending on the is strong,
volume of waste chemical
resistant and
leak proof
RADIOACTIVE Properly labelled Orange Labelled with the Radiation

WASTE RADIOACTIVE Thickness: name of proof
Labelled with the name 0.009mm radionuclide and repositories,
of radionuclide and date date of deposition leak proof and
of deposition with radioactive lead-lined
symbol container
Size varies
depending on
the volume of
radioactive
waste
NON- Tag indicating source, Black or Recycle Symbol Size varies
HAZARDOUS weight of waste colorless (non- optional for depending on
OR GENERAL generated, date of biodegradable) recyclable non- the volume of
WASTE collection Green hazardous wastes waste
(biodegradable)
Thickness:
0.009mm
Sample sizes: XL
size
39cm x 39cm x
95cm
Size varies
depending on the
volume of waste
Note:
Note: TheThe
use use of colorless
of colorless plastic
plastic linerliner
shallshall be allowed
be allowed for security
for security purposes
purposes and for
and for easier monitoring of proper waste
easier monitoring of proper waste segregation. segregation.
53
53
HCFs may adopt the color coded waste bin or innovate using recycled materials.
However, strict compliance shall be observed in the use of corresponding plastic liners
and proper labelling.
Proper tagging of plastic liners is to be strictly implemented. The tag of the plastic
liner shall indicate the name of the HCF, the area of the HCF where the waste was
generated (or the source), the type of waste, the weight and the date of collection on-
site. Tags are placed on the liners before the plastic liner is placed on the waste bin.
Figure 5.1 is an example of a sticker tag used by a HCF.
Figure 5.1 Sample Tag

Courtesy of the Philippine Heart Center, Quezon City
Aside from the information placed on the tag, yellow plastic liners should also
be labelled with a symbol appropriate for the type of waste it contains. Figure 5.2
illustrates the DENR-EMB symbols for corrosive, explosives, flammable liquids and
solids, toxic, reactives and infectious; and these symbols shall have the following
specifications:
1. The minimum size of the symbol is 25 cm x 25 cm for vessels, containers and
tanks and 30 cm x 30 cm for conveyances carrying vessels, containers and
tanks.
2. Basic shape of the symbols is a square rotated 45 degrees to form a diamond.
3. At each of the four sides, a parallel line shall be drawn to form an inner diamond
of the outer diamond.
4. The color should follow the colors specified in the figures below.
54
RECYCLABLE BIO HAZARD

SYMBOL SYMBOL
NEW RADIATION
OLD RADIATION SYMBOL
SYMBOL
IONIZING
RADIATION SIGN
CYTOTOXIC
INFECTIOUS
SYMBOL
FLAMMABLE FLAMMABLE
LIQIUID SOLID
CORROSIVE EXPLOSIVE
POISON/TOXIC
REACTIVE
SYMBOL
Figure 5.2 EMB and Other Universally Accepted Hazard Symbols
In the implementation of a color-coding system, the following practices shall be

observed:
1. Highly infectious waste must be disinfected at source.

2. Anatomical waste including recognizable body parts, placenta waste and fetus
are disposed of through safe burial or cremation.
3. Pathological waste must be refrigerated if not collected/treated within 24 hours.
55
4. Sharps waste must be shredded or crushed before transport to landfill.

5. Chemical and pharmaceutical wastes shall be segregated and collected
separately. Wastes with high content of heavy metals, except mercury, shall be
collected separately and sent to the waste treatment facility. Waste containing
mercury shall be collected separately. Mercury waste management are discussed
in DOH Department Memorandum 2011-0145. Hazardous chemical waste
shall never be mixed or disposed down the drain but shall be stored in strong
chemical resistant leak-proof container or amber disposal bottles. Expired and
discoloured pharmaceuticals shall be returned to the pharmacy for temporary
storage and be returned to the manufacturer/supplier. Pharmaceuticals shall be
kept in their original packaging for proper identification and to prevent possible
reaction with other chemicals.
6. The radioactive waste has to be decayed to background radiation levels (this is
the natural radiation level on earths crust). If it has reached the background
radiation level and is not mixed with infectious or chemical waste, then
radioactive waste is considered as regular non-infectious waste.
7. All waste bins must be properly covered to prevent cross contamination.
8. Aerosol containers can be collected with the general waste.
5.1.2 Specifications of Waste Bins and Plastic Liners

Waste bins are of different types. Some bins are designed for automated system
others are re-used plastic and metal containers. The most important is the quality of
material it shall be sturdy and leak-proof. Bins shall have well-fitting lids, either
removable by hand or operated by a foot pedal. Both the bins and the plastic liners
shall be preferably of the same color for the type of waste intended to be placed. This
is to avoid confusion and poor segregation.
Figures 5.3, 5.4 and 5.5 show examples of bins and plastic liners used in HCF.
56
a. Waste bins placed in each b. Infectious Waste Bin with yellow c. Radioactive Lead Box for
clinical area at San Lazaro plastic liner and foot pedal and Radioactive Waste
Hospital Radiation lead box used at
San Juan de Dios Educational
Foundation, Inc. (Hospital)
Figure 5.3 Example of Bins and Plastic Liners Used in HCF

Courtesy of San Juan de Dios Educational Foundation, Inc. (Hospital), Pasay City
and San Lazaro Hospital, Manila
Figure 5.4 Example of Sharp Containers Used in HCF

Disposal Bottle for Liquid Chemical Waste Container for expired pharmaceuticals Courtesy
(Courtesy of UP-National Institute of Health) of San Juan de Dios Educational Foundation, Inc.
(Hospital), Pasay City
Figure 5.5 Example of Containers for Liquid Chemical and Expired

Pharmaceutical Waste Used in HCF
Courtesy of UP-National Institute of Health, Manila and
San Juan de Dios Educational Foundation, Inc. (Hospital), Pasay City
57
Yellow Plastic liners to be used must withstand autoclaving at 121oC 130oC.

Recommended thickness of plastic liners is 0.009mm.
Only bins for general waste shall be placed in public areas.
Radioactive waste shall be placed in radiation proof containers that are leak proof
and lead-lined as shown in Figure 5.3.
Sharps should be placed in strong, puncture-proof containers that have wide mouths
and well-fitting lids as shown in Figure 5.4. Improvised bin using recyclable materials
can be adopted such as used x-ray film and hard carton/boxes.
Liquid chemical wastes shall be stored in glass amber-colored bottles, with at least
a 4L capacity as shown in Figure 5.5.
Pharmaceutical wastes including cytotoxic and genotoxic waste most of which
is produced in major hospitals or research facilities, shall be collected in strong,
leak-proof containers clearly labelled CYTOTOXIC WASTE and GENOTOXIC
WASTE, respectively. These signs shall have the minimum specification of 250 mm
x 250 mm.
Figure 5.6 Cytotoxic Waste Label (at least 250 mm x 250mm)

5.2 Waste Storage
All untreated HCW inside plastic liners shall be collected using standard trolley and
deposited to a waste storage area until transported to a designated off-site treatment
facility.
The waste in plastic liners or waste bins shall be stored in a separate area, room or
building of a size appropriate to the quantities of waste produced. There shall be a
schedule of collection depending on waste generated. In cases where the HCF lacks
the space, daily collection and treatment shall be imposed prior to disposal.
58
The HCF shall have storage areas for the following:

1. General wastes
2. Recyclable materials
3. Hazardous waste (other than phased-out mercury devices)
4. Phased-out mercury devices
If there is area available for composting of biodegradable wastes, storage area
is not necessary. It has to be disposed of directly in composting site.
5.2.1 Requirements for the Storage Area (except for phased-out mercury devices)
The Storage Area shall:
1. Be located within the HCF or research facility. However, these areas must
be located away from the dietary section, patient rooms, laboratories, hospital
function/operation rooms or any public access areas. It shall be protected from
rain, strong winds, floods, etc.
2. Allow easy access to the staff in charge of handling the waste.
3. Allow easy access for waste collection vehicle without entering hospital
premises.
4. Has a floor level higher than the anticipated flood level of the area during heavy
rainfall with concrete flooring that is waterproofed and adequately sloped for
easy cleaning and finished with ceramic tiles.
5. Have good drainage system and connected to WTP.
6. Have continuous water supply for cleaning purposes.
7. Be locked at all times to prevent access by unauthorized persons.
8. Be inaccessible to animals, insects and birds.
9. Have adequate ventilation, lighting and electrical supply.
10. Have supply of cleaning implements such as a water hose with spray nozzle,
scrubber with long handle, disinfectant, protective clothing, waste bags or bins
and fire-fighting equipment/devices located conveniently close to the storage
area.
11. Have floors, walls and ceilings clean at all times.
12. Have the warning sign posted in a conspicuous place: CAUTION:
HEALTHCARE WASTE STORAGE AREA UNAUTHORIZED
PERSONS KEEP OUT.
13. Post the HCW route plan from point of generation to the storage area.
59
Central HCW Storage for General. Recyclable, Biodegradable and Infectious Waste
Central HCW Storage for General, Recyclable, Biodegradable and Infectious Waste. A separate storage is
constructed for condemned mercury devices, fluorescent and busted lamps.
Courtesy of San Lazaro Hospital, Manila
Figure 5.7 Sample of Central HCW Storage for Hazardous and General Waste
Including Separate Storage for Condemned Fluorescent and Busted Lamps.
Cytotoxic waste shall be stored separately from other wastes in a designated secured
location. Radioactive waste shall be stored separately in containers that prevent dispersion
of radiation, and if necessary, behind lead shielding. Waste that is to be stored during
radioactive decay shall be labelled with the type of radionuclide, the date and details of
required storage conditions. Storage facility for radioactive waste must bear the sign
RADIOACTIVE WASTE placed conspicuously. Methods of treatment and disposal
of radioactive waste shall conform to the requirements and guidelines of the PNRI.
During storage for decay, radioactive waste shall be separated according to the
length of time needed for storage. For example, short-term storage (half-lives less than
30 days) and long-term storage (half-lives from 30 to 65 days). Low level radioactive
waste shall be stored for a minimum of ten times the half-life of the longest-lived
radionuclide in the container and until radioactivity decays to background levels as
60
confirmed by a radiation survey. The lead container and orange plastic for radioactive
waste are usually provided by PNRI.
Empty containers of radionuclides
solution are stored in dedicated empty
room for certain number of days until it
decays to background level.
Mercury wastes shall be collected and
stored in the designated storage area. It
shall be clear that the mercury wastes
require a more thorough storage system.
Mercury containing products must be
stored in non-breakable containers with
tight-fitting lids. The containers must
be clearly labelled as to their contents.
Rooms
where mercury containing items are stored
shall be tested periodically using a mercury vapour sniffer or analyzer. Even after
the use of mercury has long been discontinued in the HCF, mercury containing
products may still be in storage from past uses. All HCF shall check storage areas
for old, damaged or outdated equipment. If mercury-containing products are found,
contact the healthcare waste management officer. After the removal of the mercury-
containing products, the areas shall be checked with the mercury vapour sniffer or
analyzer. HCF shall keep a permanent record of all materials brought in and out of the
mercury storage area. The safe handling, transport and temporary storage of mercury
waste are discussed thoroughly in Annex A of Department Memorandum No. 2011-
0145 dated April 11, 2011. Also, the management of mercury spills is spelled-out in
details in Annex B of the said Memorandum.
Dedicated room as
Mercury Storage Area
Sample of packaging and storing of mercury containing devices using available Courtesy of San Juan
resources. Courtesy of San Lazaro Hospital, Manila de Dios Educational
Foundation, Inc.
(Hospital), Pasay City
Figure 5.9 Sample of HCF Management of Mercury Containing Devices.

61
5.3 Collection and Transport of HCW

Proper collection and transport of HCW is an important component in HCWM.
Its implementation requires commitment and cooperation of the HCFs maintenance,
housekeeping and motor pool services personnel and all the HCF workers.
HCW collection practices shall be designed to achieve an efficient movement of
waste from point of generation to storage or treatment while minimizing the risk to
personnel.
Suggested collection frequency on room to room basis is once every shift or as often
as necessary depending on the volume of waste generated. Collection of waste shall
be completed by the end of every shift.
5.3.1 On-Site Collection of HCW

This refers to the collection of waste using transport trolleys from the waste bins to
the central storage area of the HCF by the general service personnel. The following
guidelines shall be observed by HCF worker directly involved in waste handling and
collection:
1. Follow the established plan for the collection and transport of HCW.
2. Collect daily (or as frequently as required) and transport HCW to the designated
central storage area.
3. Ensure that plastic liners are tightly closed or sealed and properly tagged with
source and weight.
4. Replace the plastic liners immediately with new ones of the same color upon
collection.
5.3.2 On-Site Transport of HCW

This refers to the transport of waste from the point of generation to the treatment
facility in the HCF or to the central storage area.
5.3.2.1 Standard Requirements (Tools, Devices and Equipment and PPE)

In any HCF, the standard requirements to transport HCW from source to the
designated central storage area include:
There shall be dedicated trolleys for each waste category - one for infectious waste;
one for non-biodegradable and one for biodegradable/recyclable waste. No mixing of
waste must be done.
62
Figure 5.10 On-Site Collection of Healthcare Waste.

Transport trolleys shall be dedicated to waste transport. Use on-site transport

trolley that can accommodate three collection bins and shall meet the following
requirements:
Easy loading and unloading
Easy to clean
Heavy duty wheel caster
Figure 5.11 a: Dedicated Trolley That Can Carry at Least Three Big Containers
for Infectious and General Waste (Biodegradable and Non-Biodegradable)
Courtesy of Dr. Jose R. Reyes Memorial Medical Center, Manila
63
Figure 5.11 b: Single Trolley with Heavy Duty Wheels and

with a Capacity of 50-60 kilos.
On-site transport of HCW in HCF with more than two storey building/s shall
use service elevators, mechanical pulley, hoist or ramp. In the case of elevators or
ramps, the schedule of on-site transport of HCW shall be prior to the end of shift of
workers, preferably not coinciding with scheduled visiting hours. The trolleys shall
be disinfected after every use.
The on-site transport trolley shall be cleaned and disinfected daily using 4-5%
concentration of sodium hypochlorite (NaClO).
Workers transporting the waste must be equipped with appropriate PPE (see Chapter
9 on Health and Safety Practices).
Figure 5.12 HCW Handlers with Appropriate PPE.

Courtesy of Dr. Jose R. Reyes Memorial Medical Center, Manila
64
5.3.2.2 Healthcare Waste Transport Routing

HCW shall be transported through the quickest or shortest possible route and shall
be planned before the trip begins. Upon departure from the source, no further handling
shall be done. An efficient and effective collection system route shall consider the
following:
Collection schedule either by route or zone
Assignment of worker responsible for the zone or area
Logical planning of the route (shall avoid passing congested areas)
Start from farthest point of the designated transfer station and progress towards
the waste storage area.
Practical routes
All logical progression of HCW
Suggested collection frequency on room to room basis is once every shift or as
often as necessary depending on the volume of wastes.
Schedule of collection
Established routing plan can be revised if circumstances warrant it.
Figure 5.13 illustrates a sample routing plan.
Figure 5.13 Sample Transport Route Plan for Healthcare Waste

65
5.3.3 Off-Site Collection of HCW

This refers to the collection of waste from the central storage area by an accredited
DENR transporter, Municipal Collector or Supplier into their respective vehicles. The
waste collector at this point will depend on the type of waste collected. The off-site
collector of HCW shall provide collection bins that meet the following requirements:
Puncture-proof for sharps

Resistant to aggressive chemicals
Made of high density polyethylene materials (HDPE)
Must be leak-proof and be fitted with a self-sealing lid that is tight enough to
withstand turbulence during transport in the vehicle
Must follow the requirements of EMB-DENR
Infectious and pathological waste must be placed in appropriate color-coded or

other special bins when transported.
In case of radioactive wastes, it must be packaged for off-site collection and
transported in accordance with the accepted criteria for low level radioactive wastes
established by PNRI (AO No. 01 series of 1990).
5.3.4 Off-Ste Transport of HCW

This refers to the transport of waste from the central storage of the HCF to a TSD
or to the final disposal site. The HCW generator is responsible for the safe packaging
and adequate labelling of waste to be transported off-site for treatment and disposal.
Packaging and labelling shall comply with the national regulation governing the
transport of hazardous wastes (RA 6969) and present no danger to the public during
transport. Likewise, the waste generators are ultimately responsible for ensuring
that their HCW are properly treated and disposed of in an approved disposal facility.
Tracking of HCW could be done with the implementation of the consignment system.
The transporter shall comply with DENR requirements and be registered with the
DENR as waste transporter.
Consignment Note
All HCW to be transported to an approved off-site waste treatment facility shall be
transported only by a DENR-accredited transporter or carrier, except non-hazardous
HCW which are collected by the municipal collection system. The authorized
transporter/carrier shall maintain a completed consignment note (see Annex B for a
prototype Consignment Note) of all HCW for treatment or disposal and an updated
transport permit.
Upon the receipt of the wastes, the transporter shall provide the waste generator with
a copy of the consignment note for the generators waste records.
66
The transporter and generator shall separately maintain a copy of the consignment
note. The consignment note shall include, but is not limited to the following
information:
The name, address, telephone number and accreditation number of the transporter,
unless the transporter is the generator.
The type and quantity of HCW transported.
The name, address and telephone number of the generator.
The name, address, telephone number, permit number and the signature of an
authorized representative of the approved facility receiving the HCW.
The date that the HCW is collected or removed from the generators facility, the
date that the HCW is received by the transfer station or point of consolidation (if
applicable) and the date that the HCW is received by the treatment facility.
If the HCW generator transports the waste or directs a member of its staff to transport
the HCW to an approved waste treatment and disposal facility, the consignment
note for the HCW shall show the name, address and telephone number of the HCW
generator when the HCW are transported to the waste treatment and disposal facility.
The transporter or generator transporting the HCW shall have the consignment
note in his or her possession in the vehicle while transporting the waste. The
tracking document shall be available upon demand by any traffic enforcement agency
personnel. The transporter shall provide the facility receiving the waste with a copy
of the original tracking document.
5.3.5 Emergency Contingency Plan for HCW Transporter

The development of a plan of action shall be considered in the event of an accidental
spill, loss of containment, equipment failure or other unexpected circumstances.
The owner/operator of vehicles used in the transport of HCW shall carry contingency
plans for emergencies that address the following:
Plan for the disinfection of the truck and any contaminated surface if a leaking
container is discovered.
A notification list of individuals or agencies to be contacted in the event of a
transport accident.
Clean-up and decontamination of potentially contaminated surfaces, designation
of back-up transport for the HCW, a description of the plans for the repackaging
and labelling of HCW where bins are no longer intact.
Procedures for the management of leaking container/s.
Other EMB-DENR requirements.
67
5.3.5.1 Requirements for Off-site Transport Vehicles

Transport vehicles for HCW shall not be used for the transport of any other
materials that could be seriously affected by contamination such as food, livestock or
retail goods. The vehicle shall have an enclosed leak-proof body and capable of being
locked to secure the HCW. HCW can be loaded directly to a specially designed vehicle,
but it is safer to place them first in containers (e.g. cardboard boxes or wheeled, rigid,
lidded plastic or galvanized bins). The design of the collection vehicle must conform
to the following:
The body shall be of suitable size commensurate with the design of the vehicle.
It shall have a totally enclosed car body with the drivers seat separated from the
load to prevent coming into contact with the HCW in the event of a collision/
accident.
The body of the vehicle shall display the international biohazard sign including
emergency telephone number.
The body shall be marked with the name and address of the waste carrier.
It shall have a suitable system for securing the load during transport.
It shall be easy to clean.
The internal surface of the body shall be smooth enough to allow it to be cleaned
with wet steam or hot water.
The internal surface of the body shall have round corners.
It shall be equipped with a separate compartment containing empty plastic bags,
suitable protective clothing, cleaning equipment, tools, disinfectants and special
kits for dealing with liquid spills.
It shall strictly comply with EMB-DENR requirements.
68
WASTE TREATMENT AND DISPOSAL SYSTEM
Chapter 6: Waste Treatment and Disposal System

Healthcare waste treatment is necessary to ensure the safety and protection of HCF
workers, patients and the general public as well as to protect the environment from
hazards of HCWs. This chapter will illustrate the different technologies and methods
in waste treatment and disposal.
6.1 Healthcare Waste Treatment

In determining the method to be used in waste treatment and disposal by any HCF,
the HCF administrator has to look into several requirements and conditions relevant
to HCWM. The purpose of treating HCW is to change the biological and chemical
character of the waste to minimize its potential to cause harm. There are a number of
terms used to denote the level of treatment of HCWs, such as sterilization, disinfection
and decontamination.
Defining safe management of HCW treatment will demonstrate the ability to reduce
the number of infectious pathogens in HCW to an acceptable level to protect workers
or the public against any contamination/infection. One of the universally accepted
methods of treatment is sterilization.
Sterilization is defined as a 6log10 survival probability of the most resistant
microorganism of concern in a given process. On the other hand, Disinfection is
defined as low, intermediate or high (using the Spaulding system) depending on the
survival probability of specific microbial groups. For medical waste disinfection,
however, the emerging international consensus is to define levels of microbial
inactivation as follows:
Level I Inactivation of vegetative bacteria, fungi and lipophilic viruses at 6log10

reduction or greater
Level II Inactivation of vegetative, fungi, lipophilic/hydrophilic viruses,
parasites and mycobacteria at 6log10 reduction or greater
Level III Inactivation of vegetative bacteria, fungi, lipophilic/hydrophilic viruses,
parasites and mycobacteria at a 6log10 reduction or greater; and inactivation of B.
stearothermophilus spores and B. subtilis spores at 4log10 reduction or greater
Level IV Inactivation of vegetative bacteria, fungi, lipophilic/hydrophilic
viruses, parasites and mycobacteria and B. stearothermophilus spores at a 6log10
reduction or greater
Mechanical grinding devices are sometimes needed prior to treatment, during

treatment and/or at the end of the treatment process. Some technologies, however, depend
on shredding as an integral part of the treatment process, i.e. those systems that shred
prior to treatment and during treatment. Shredders are typically a high maintenance item
due to unavoidable volumes of trapped waste in the waste stream, such as high-quality
69
stainless steel found in orthopaedic blades, drills, reamers and prosthetic devices.
Glass is also inherent in HCWs and overtime glass wears the cutting surface of the
shredder blades. Therefore, if the facility intends to shred wastes either in pre- or post-
treatment, anticipate that a rigorous maintenance schedule with associated cost would
be required. Shredding the waste simply to render it unrecognizable makes the task
more burdensome and more expensive than necessary and a cost benefit analysis must
be conducted prior to making that decision. Also, the potential down time when the
shredder is out of commission should be considered.
6.2 Selection Criteria of Healthcare Waste Treatment Technology

In selecting an HCW treatment and disposal method, the HCF shall perform a
preliminary assessment and determine the issues that are important to the facility and
develop a list of selection criteria and rank in order of importance. Various key points
should be taken into account, such as the following:
Treatment efficiency
Occupational health and safety and environmental considerations
Volume and mass reduction
Types and quantity of waste for treatment and disposal / capacity of the system
Infrastructure and space requirements
Locally available treatment options for final disposal
Training requirements for operation of the method
Cost of operation and maintenance
Location/surroundings of the treatment site and disposal facility
Regulatory requirements
Social and political acceptability
The selection of HCW technology goes far beyond cost implications since this may
have significant impact on the environment, the workers in the treatment and disposal
facilities and the surrounding community. Several questions need to be asked and
answered regarding this matter.
On-site treatment of HCW allows the HCF to have more control over both the waste
treatment process and cost. Off-site treatment maybe a cost-effective alternative and
many of its manufacturers have already simplified their systems so that processing is
relatively effortless.
The following are some guide questions that the HCF can use when deciding what
technology to use.
70
6.2.1 On-Site Treatment Technologies

How important is volume reduction in choosing a technology? What is the ratio
of HCW produced by your HCF to the HCW treated by the treatment technology?
Is the technology dependent on the volume of waste?
How would waste reduction programs affect the process? If the waste volume
changes radically for any reason (e.g. reduced patient-days, merger, better waste
minimization efforts) will this technology still be the treatment needed?
Have workers from your HCF talked to colleagues at other HCFs about their
treatment options, made comparisons, discussed technologies, contracts and
services, as well as violation histories and ranges of service costs?
What is the Philippine regulatory climate for on-site treatment technologies?
(Some types of technologies require more complicated permits than others)
Does your HCF have workers on-site that are trained and certified to fulfil the
testing requirements, time, etc. involved in these permits? If not, consider those
staffing and testing costs in your evaluation.
How long has the treatment technology been effectively in use and where?
What is the estimated life of this equipment?
What volume of waste can the technology handle and treat?
Will it always be operating at peak capacity or will there be wide variations in the
amount of HCW treated?
What are the operational cost implications of using this technology? What are the
environmental and fiscal impacts of utilities usage (electricity, water and sewer)?
What is the safety and repair history of the waste treatment equipment?
What worker safety and on-going equipment education are required and who
provides it?
What are the cost/s of equipment failure and need for a back-up or alternative
system?
Is waste fed into the treatment system automatically (by machine) or by hand
(stop feed)? What impact does this have on your HCF workers limitations?
Can equipment repair be completed within 24 hours without an emergency
clause and/or additional costs?
Does the technology require ancillary equipment such as shredders? Are they an
integral part of the treatment process?
What are the total associated costs for this equipment?
Are there any worker-safety concerns with this equipment?
How is the volume and weight of the HCW measured?
Who measures it? Is it cost-effective to weigh the wastes on-site?
71
6.2.2 Off-Site TSD Facility

How many trucks will enter and leave the HCF daily? Will traffic vary by day
of the week or remain fairly constant?
From what geographic area will HCW be accepted? What sort(s) of waste will
be treated?
Is it possible to bargain collectively with TSD for waste treatment and disposal
services?
Are there any equipment violations against the TSD your HCF is considering?
Is the TSD fully permitted?
Are there any community or environmental health concerns associated with this
TSD?
If the decision is to let a TSD treat the HCW, then the cost to be considered would
only be the charge of the TSD and the associated transportation cost. However, if
the decision is to invest in an on-site facility, then the following costs need to be
considered:
Capital equipment costs
Installation and facility costs: installation labor, facility modifications cement
pad/s, curb cuts, sewers, electricity, space, security, etc.
Costs of pollution control equipment if required to control emissions and
effluents from the treatment facility
Direct labor costs: number of employees needed to operate the treatment
equipment
Down time costs: including repair (parts and labor), and alternative treatment
Operating costs if the facility uses special chemicals and catalysts
Utility costs
Permitting and compliance fees: water and air quality monitoring fees
Fines: depending on permitting requirements, national and local regulations,
violations of permits or emissions
All transportation, processing and tipping fees
Supply costs PPE, spill supplies, special bags (for example some autoclaving
systems require particular bags), collection bins (boxes or reusable containers)
Community approval costs if a public hearing is required
6.3 Healthcare Waste Treatment Technologies/Processes

Most common technologies and methods used in HCW treatment are:
1. Thermal 4. Biological Process
2. Chemical 5. Encapsulation
3. Irradiation 6. Inertization
72
Table 6.1 Acceptable Technologies and Methods Used in the Treatment of HCW
HCW
TREATMENT DESCRIPTION APPLICABILITY REMARKS
TECHNOLOGY/
METHODS
1. Pyrolysis Thermal decomposition of HCW in the All types of waste Costly. Not
absence of supplied molecular oxygen except mercury yet available
in the destruction chamber in which the waste in the country
said HCW is converted into gaseous,
liquid, or solid form. Pyrolysis can
handle the full range of HCW. Waste
residues may be in form of greasy
aggregates or slugs, recoverable
metals, or carbon black. These residues
are disposed of in a landfill.
2. Autoclave Uses steam sterilization to render waste All types of waste Relatively low
harmless and is an efficient wet thermal except anatomical/ investment
disinfection process. This technique has pathological, and operating
been used for many years in hospitals e x p i r e d costs.
for the sterilization of reusable medical pharmaceutical Av a i l a b l e
equipment. Autoclaves come in a wide drugs, cytotoxic, in different
range of sizes. A typical autoclave c h e m i c a l , models and
designed for medical waste treats about radioactive waste, capacity to
100 kg per cycle (a cycle being about 1 and mercury waste suit the needs
hour) to several hundred kilograms per of big and
cycle for larger hospitals. Autoclaves Autoclaves used for small HCF
used in centralized treatment facilities HCW should have a Has no
can handle as much as 3,000 kg in built-in shredder. significant
one cycle. The microbial inactivation environ-
efficacy of autoclaves shall be checked m e n t a l
periodically. For autoclaves that do not a d v e r s e
shred waste during steam disinfection, impact
color-changing indicator strips may be
inserted inside the yellow bag in the
middle of each load and that the strip
shall be checked to ensure that steam
penetration has occurred. In addition, a
microbiological test (using for example
commercially available validation kits
containing Bacillus stearothermophilus
spore strips, vials or packs) shall be
conducted periodically or as the need
arises.
73
HCW
TECHNOLOGY/
METHODS
3. Microwave This technology typically The process is The system
incorporates some type of size inappropriate has a
reduction device. Shredding of for the treatment relatively high
wastes is done before disinfection. of anatomical investment
In this process, waste is exposed waste and animal and operating
to microwaves that raises the carcasses, and costs.
temperature to 100oC (237.6oF) for will not efficiently Not
at least 30 minutes. Microorganisms treat chemical or recommended
are destroyed by moist heat which pharmaceutical for individual
irreversibly coagulates and denatures waste HCF
enzymes and structural proteins.
4. Chemical Chemical disinfection is also Chemical Application
Disinfection being used for treatment of HCW. disinfection is most of this method
Chemicals like sodium hypochlorite, suitable in treating shall only be
hydrogen peroxide, peroxyacetic blood, urine, stools done when
acid and heated alkali are added to and sewage. This there is no
HCW to kill or inactivate pathogens method is used in available
present. It is recommended that disinfecting highly treatment
sodium hypochlorite (bleach) with infectious wastes at facility in
a concentration of 5% be used for source as defined in the area
chemical disinfection. If possible, this manual. to prevent
HCW shall be shredded to increase environmental
the extent of contact between HCW problems
and the disinfectant by increasing associated
the surface area and eliminating the in the
enclosed space. indiscriminate
Some precautionary measures should use of
be taken into consideration before chemicals as
using chemical disinfection: required by
-Shredding and/or milling of waste is RA 8749 or
usually necessary before disinfection; the Clean Air
the shredder is often the weak point Act and RA
in the treatment chain, being subject 9275 or the
to frequent mechanical failure or Clean Water
breakdown. Act
-Powerful disinfectants are required,
which are themselves also hazardous
and should be used only by well
trained and adequately protected
personnel.
-Disinfection efficiency depends on
operational conditions.
-Only the surface of intact solid
waste will be disinfected
74
HCW
TECHNOLOGY/
METHODS
5. Biological The process uses an enzyme mixture Biodegradable Design
Processes to decontaminate HCW. The wastes such as a p p l i c a t i o n
resulting by-product is put through food waste, etc. is mainly
an extruder to remove water for for regional
wastewater disposal. The technology H C W
is suited for large applications and treatment
is also being developed for possible center.
use in the agricultural sector.
However, the technology requires
regulation of temperature, pH,
enzyme level, and other variables.
Composting and vermin-culture as
biological processes for food waste,
yard trimmings and other organic
waste are also recommended.
6. Encapsulation Encapsulation involves the filling of The process The main
containers with waste, adding and is particularly advantage of
immobilizing material, and sealing appropriated the process
the containers. The process uses either for the disposal is that it is
cubic boxes made of high-density of sharps very effective
polyethylene or metallic drums, and chemical in reducing
that are three-quarters filled with (solid form) or the risk of
sharps or chemical or pharmaceutical pharmaceutical scavengers
residues. The containers or boxes residues. g a i n i n g
are then filled up with a medium access to the
such as plastic foam, bituminous HCW.
sand and cement mortar. After the
medium has dried, the containers are
sealed and disposed of in landfill.
7. Inertization Especially suitable for The process This is to
pharmaceutical waste is the process is particularly minimize the
of inertization that involves the appropriate for the risk of toxic
mixing of the waste with cement and disposal of sharps substances
other substances before disposal. For and chemical contained
the inertization of pharmaceutical (solid form) or in the
waste, the packaging shall be pharmaceutical waste from
removed, the pharmaceuticals residues. migrating
ground, and a mixture of water, lime into the
and cement added. The homogenous surface water
mass produced can be transported to or ground
a suitable storage site. Alternatively, water.
the homogeneous mixture can
be transported in liquid state to a
landfill and poured into municipal
waste. The process is relatively
inexpensive and can be performed
using relatively unsophisticated
equipment. The following is the
typical proportion for the mixture:
65% pharmaceutical waste, 15%
lime, 15% cement and 5% water.
75
It should be noted that there may be other technologies efficient and effective in the
treatment of HCW that are not mentioned in the above table. These other treatment
technologies may be used in the treatment of HCW in the Philippines, provided they
are approved and certified by the DOH and the DENR.
In choosing the application of chemical disinfection the following considerations
shall be looked into:
Studies showed that chlorine-based technologies using sodium hypochlorite and

chlorine dioxide as well as its by-products in wastewater may possibly have
long-term environmental effects.
Non-chlorine based technologies are quite varied in the way they operate and
the chemical agents they employ. Others use peroxyacetic acid, ozone gas,
lime-based dry powder, acid and metal catalyst or biodegradable disinfectants.
Occupational and safety exposures shall be monitored when using the chemical
process.
In planning the use of chemical disinfection, requirements for the eventual
disposal of the residues should be carefully considered. Improper disposal could
give rise to serious environmental problems.
6.4 On-Site Waste Treatment Facilities

A hospital may opt to have an on-site treatment of their HCW. However, some
factors should be considered before going into this option.
Figure 6.1 Autoclave

Image taken from the UP-National Institute of Health
The treatment facility shall:

1. Have safe transfer routes.
2. Be located within the HCF. However, these areas must be located away from the
dietary section, patient rooms, laboratories, hospital function/operation rooms or
any public access areas.
3. Be located in a way that it does not produce nuisance such as odor, noise, the
visual impact of HCW operations on patients and visitors.
76
4. Public access and security.

5. Consider the proximity of the treatment facility to the temporary or central
storage.
6. Be strategically placed so as not to cause traffic problems in the entry and exit
of vehicles.
7. Consider the volume of waste generated by the HCF when it comes to the size
of the treatment facility.
8. Be protected from rain, strong winds, floods, etc.
9. Have elevated, concrete finish flooring and with waterproofing, adequately
sloped for easy cleaning.
10. Have a good drainage system and connected to a WTP.
11. Have continuous water supply for cleaning purposes.
12. Have locking device to prevent access by unauthorized persons.
13. Be inaccessible to animals, insects and birds.
14. Have adequate ventilation and lighting
15. Have supplies of cleaning implements such as a water hose with spray nozzle,
scrubber with long handle, disinfectant, protective clothing, waste bags or bins
and fire-fighting equipment/devices located conveniently close to the storage
area.
16. Have space allowances needed by workers to maneuver safely around the
treatment facility.
17. Have floors, walls and ceilings that are clean at all times.
18. Have a warning sign posted in a strategic place: CAUTION: TREATMENT
AREA: UNAUTHORIZED PERSONS KEEP OUT.
Each technology has different requirements for space, foundation, utility service
connections, ventilation and support equipment.
6.5 Waste Disposal System

6.5.1 Landfill
Landfill is an engineered method designed to keep the waste isolated from the
environment. Appropriate engineering preparations and corresponding permits from
DENR shall be completed before the site is allowed to accept waste. There shall be a
trained staff present on-site to control and manage the operations.
The landfill shall:
Be accessible to site and working areas for easy passage of delivery access
Have landfill personnel capable of effective control of daily operations
Divide the site into manageable phases, which are appropriately prepared, before
disposal of wastes
77
Have adequate sealing of the base and sides to minimize the movement of
wastewater (leachate)
Have adequate mechanisms for leachate collection and treatment systems
Have an organized deposit of waste in a small area, allowing waste to be spread,
compacted and covered daily
Have surface water collection trenches around site boundaries
Have a construction of a final cover to minimize rainwater infiltration when each
phase of the landfill is completed
Figure 6.2 Metro Clark Sanitary Landfill

Courtesy of Infratex Philippines Incorporated
HCW that is properly treated with the applicable technology as stated in this
Manual can be mixed with general waste provided DOH issues a certification that the
microbes in the treated HCW are inert and will not regenerate. DOH will formulate
the guidelines for the issuance of the certification. Certification for the treated HCW
can be secured from the DOH provided it conforms to the following:
1. The waste treatment facility/system passed the standards for microbial
inactivation test;
2. The properly treated HCW passed the spore strip test;
3. The waste treatment facility/system has a valid CPR from the DOH-Bureau of
Health Devices and Technology (BHDT); and
4. The waste treatment facility is an EMB-registered TSD.
78
6.5.2 Safe Burial at HCF Located in Remote Areas

Safe burial as a disposal method is applicable only to treated infectious waste,
sharps waste, pathological and anatomical waste, small quantities of encapsulated/
inertisized solid chemical and pharmaceutical wastes.
Figure 6.3 Safe Burial Pit (volume of 1m x 1m x 1.8m)
Safe burial of HCW is allowed in the following situations:
1. HCF is located in a remote and far-flung area

2. HCF does not have access to TSD facilities
3. HCF is located in an LGU with an income classification of 5th or 6th Class
4. HCF located in 1st to 4th Class LGU has available area within the HCF premises
(only pathological, anatomical, expired drugs and sharps wastes can be buried)
5. Safe burial of HCW within the HCF premises is the only viable option at a
specific period of time.
The Safe Burial Site shall:
Be accessible only to authorized personnel.

Be lined with a material of low permeability, such as clay or HPDE, to prevent
pollution of shallow groundwater that may subsequently reach nearby wells.
Allow only hazardous HCW to be buried. If general HCW are also buried on the
premises, available space would be quickly filled-up.
Be managed as a landfill, with each layer of waste covered with a layer of earth
to prevent odor, as well as to prevent proliferation of rodents and insects.
79
Not be located in flood prone areas.

Be secured (e.g. fenced with warning signs).
Be downhill or down-gradient from any nearby wells and about 50 meters away
from any water body such as rivers or lakes to prevent contaminating water
source.
Have the bottom of the pit located at least 1.5 meters above ground water level.
HCF shall keep a permanent record of the size and location of all their on-site
burial pits to prevent construction workers, builders and others from digging in those
areas in the future. The safe burial of waste depends critically on rational operational
practices. It shall be noted that safe on-site burial is practicable only for relatively
limited period, about 1 to 2 years, and for relatively small quantities of waste, about 5
to 10 tons in total. When these conditions have been exceeded, a long-term solution
will be needed.
6.5.3 Septic/Concrete Vault

This method is especially suitable for the disposal of used sharps and syringes. The
following steps shall be observed:
1. Select a site that is isolated and at least 150 meters away from the water supply
sources and dwelling units.
2. Dig a pit (minimum size of 1m x 1m x 1.8m depth) enough to accommodate
sharps and syringes for an estimated period of time without reaching the
groundwater level.
3. Construct concrete walls and slabs of pit.
4. Provide slab with opening or manhole for easy deposition of collected sharps
and syringes. The manhole shall be extended a few centimeters above the soil
surface to overcome infiltration of surface water.
5. Deposit the collected safety boxes filled with used sharps and needles inside the
concrete vault.
6. Install a security fence around the site with signage.
80
Figure 6.4 Concrete Vault
6.6 Summary of Healthcare Waste Handling

Based on the discussion of Chapters Five and Six, there are seven important points
in waste handling. These include the following:
1. Waste Generation
2. Waste Segregation
3. Waste Collection
4. Waste Transportation
5. Waste Storage
6. Waste Treatment
7. Waste Disposal
Waste management will vary depending on the type of wastes being handled. Table
6.2 summarizes the options in handling the different types of wastes.
81
Table 6.2 Healthcare Waste Handling
82
83
84
85
Table 6.2 presents the general rule in handling HCW. However, there are some
important points to remember in the handling of wastes:
1. In order for properly treated HCW to be collected and disposed together with
general waste, there should be a certification issued by the DOH that the microbes
in the properly treated HCW are inert and will not regenerate. The guidelines to
implement this provision will be issued by DOH.
2. Not all yellow plastic liners are autoclaveable. In this Manual, yellow
autoclaveable plastic liner for infectious waste is stipulated. For other types of
waste, a non-autoclaveable yellow plastic liner with the correct specifications
may be used.
3. Chemical disinfection as a treatment method will only be used when all other
treatment technologies are not available to the HCF. Precautionary measures to
be applied when using chemical disinfection are discussed in Section 6.3 and
Table 6.1 of this chapter.
4. The HCF should be guided by the Chain of Infection in handling highly
infectious wastes contaminated with heat and chemical resistant pathogens
(such as transmissible spongiform encephalitis brought about by prions).
86
MANAGING WASTEWATER GENERATED BY HEALTHCARE FACILITIES
Chapter 7: Managing Wastewater Generated by

Healthcare Facilities
The Philippine Clean Water Act of 2004 requires the government to implement anti-
degradation measures to preserve the quality of water bodies and proper water quality
management programs. It includes the following: monitoring, inspection and survey
of firms and establishments within the jurisdiction of its offices; effluent monitoring
and sampling; and ambient water quality monitoring of water bodies.
The passage of the Clean Water Act mandated the putting up of Wastewater
Treatment Plants (WTP) and provision of sanitation facilities in each locality. Human
excreta are the principal vehicle for the transmission and spread of wide range of
communicable diseases. Excreta from healthcare patients may be expected to contain
far higher concentration of pathogens, and therefore are far more infectious than
excreta from households. This underlines the prime importance of providing access to
adequate sanitation in every HCF. The HCF shall be connected to a municipal WTP
or must have its own WTP.
WHO defines wastewater as liquid waste discharged from, among others, HCF to
individual disposal systems or to municipal sewer pipes and which contains mainly
human excreta and used water.
All HCFs shall have their own WTP or be connected to a municipal or common
WTP or equivalent system for small HCFs (with bed capacity of 25 or less).
7.1 Composition of Wastewater

Wastewater from HCFs contains organic particles (feces, hairs, food, vomit, paper
fibres, etc.), soluble organic material (urea, proteins, pharmaceuticals, etc.), inorganic
particles (sand, grit and metal particles), soluble inorganic material (ammonia, cyanide,
hydrogen sulphide, thiosulphates) and other substances. The composition depends on
the source of origin.
7.2 Sources of Wastewater and Its Characteristics

Table 7.1 indicates the possible sources of wastewater within the HCF and the
different characteristics of the wastewater produced in each source.
87
Table 7.1 Sources of Wastewater and Its Characteristics
HCF Department Wastewater Characteristics

Administration and Wards Urine of patients from some wards (surgery wards,
oncology, infectious disease ward, etc.) might
contain higher amounts of antibiotics, cytotoxic
and X-ray contrast media.
Kitchen Food leftovers, waste from food processing,
disinfectants and detergents, starch, grease and oil.
Laundry The wastewater often is hot, has a high pH (alkaline)
and might contain high amounts of phosphate,
surfactants and AOX (adsorbable organically
bound halogens) if chlorine based disinfectants are
used.
Operating Room and ICU Higher contents of disinfectants, detergents and
pharmaceuticals. Organic content can be high due
to the disposal of body fluids and rinsing liquids
(suction containers).
Laboratories Halogenated and organic solvents, colorants from
the histology and haematology (gram staining),
cyanides (haematology) and formaldehyde and
xylem (pathology) and other reagents, wastewater
from autoclaves.
Radiology Photochemical (developing and fixing solutions)
containing waste water and potentially
contaminated rinsing water, fixers and developers.
Renal Department Body fluids from machine, disinfectants, dialyzer
solutions, wastewater from reverse osmosis
process.
Dental Department Mercury (amalgam) if no amalgam separators are
installed; disinfectant, body fluids, wastewater
from autoclaves.
Central Sterilization Room Disinfection solution, including aldehyde based
disinfectants. Hot water from the sterilizers and
detergents from the CD Machine (Cleaning and
Disinfection) wastewater from autoclaves and
sterilizing equipment.
Knowing the characteristic of the wastewater produced by the HCFs will give an
idea of the risks associated with the discharge. This will also determine the type of
treatment that the wastewater needs before it can be released or reused.
88
7.3 Collection, Treatment and Disposal of Wastewater

Depending on wastewater characteristic, the HCF may provide a pre-treatment
system, connected to a centralized wastewater system, or provide its own on-site
wastewater treatment system. According to DENR AO No. 35 of 1990, wastewater
with a minimum BOD of 3,000mg/L is considered strong wastewater and its effluent
is to be discharged to Class C and D bodies of water with a minimum concentration of
50 mg/L.
7.4 Connection of HCF Wastewater to a Centralized Wastewater System

Subject to the guidelines of the DENR and wastewater service provider, the HCF
shall connect its existing septic tanks to the centralized wastewater treatment facility.
7.5 On-site Wastewater Treatment Plant (WTP)
a) Exterior View, with control room on b) Primary Treatment

the far left
c) Secondary and Tertiary Treatment d) Effluent
89
e) Chamber
Figure 7.1 Wastewater Treatment Plant

7.5.1 Pre-Treatment Stage

The basic principle underlying effective wastewater management is a strict limit
on the discharge of hazardous liquids to sewers. For wastewater streams from certain
departments, such as the laboratory, a pre-treatment is recommended.
Hazardous Chemical Waste, especially photo-chemicals, aldehydes (formaldehyde
and glutaraldehyde), colorants and pharmaceuticals shall not be discharged in the sewer
lines but separately collected and treated. Other chemicals that cannot be disposed
down the drain are those included in DENR AO 36-2004. Solid wastes, chemicals,
pharmaceuticals, grease, oil and paints in large quantities shall not be discharged into
the sewer.
Chlorine-based disinfectants (such as sodium hypochlorite) shall not be disposed of
in a septic tank as it will harm the bacteria used for the biological treatment process.
Body-fluids and the contents of suction systems from infectious patients from the
operating room shall be thermally treated first (e.g. by autoclave reserved for waste
treatment) before being discharged down the drain.
Expired blood bags shall not be emptied into a sink because of the risk of infection
from blood splatters.
Grease traps shall be installed to collect grease, oil and other floating materials from
the kitchen. Collected grease must be removed daily.
90
Body fluids, blood and rinsing liquids from the OR and the ICU shall first be
disinfected preferably with a thermal method, especially if the patient is suffering
from infectious disease.
Wastewater from the dental department shall be pre-treated by installing amalgam
strainer/separator.
Patients given high doses of radioactive isotope for therapy shall be given toilet
facility separate from those used by non-radioactive patients; and radioactive
patients shall be instructed to use the same toilet bowl at all times and flush it at least
three times after use.
7.5.2 Primary Treatment Stage

This involves physical treatment to remove settleable solids, large objects such
as sand, grit and stones; and floating materials such as grease and plastics. These
items shall be removed so as not to affect the secondary treatment. Primary treatment
includes multi-chamber septic tanks, mechanical screens, grit chambers and settling
tanks.
7.5.3 Secondary Treatment Stage

This involves biological treatment to remove dissolved organic substances
using microbes. The bacteria and protozoa consume biodegradable soluble organic
contaminants (sugars, fats, organic short-chain carbon molecules, etc.). Oxygen has
to be supplied to microbes to accelerate their growth and the process of consumption.
Examples of technologies applied are trickling filters, activated sludge, anaerobic
baffled reactor (ABR), sequencing batch reactor (SBR), waste stabilization pond and
engineered reed bed.
7.5.4 Tertiary Treatment Stage

This final stage removes microorganism and excessive nutrients in wastewater,
such as nitrogen and phosphorus that may adversely affect the quality of the receiving
body of water. Examples are UV-hygienization and chlorine disinfection. Quality of
effluent to be disposed after tertiary treatment shall be subject to DENR AO No. 35.
- Biological Oxygen Demand (BOD) 50 mg/L or below

- Chemical Oxygen Demand (COD) 100 mg/L or below
- Total Suspended Solids (TSS) 70 mg/L or below
- Settleable Solids 0.3 mg/L or below
- Oil and Grease 5 mg/L or below
- Surfactant 5.0 mg/L or below
- pH 69
- Total Coliform (E.coli) 5000 MPN/100ml or below
91
7.6 Factors to be Considered in the Establishment of an On-Site WTP

To have an efficient and cost-effective establishment of on-site WTP, it is important
to have an objective approach in considering the following factors:
Regulatory Requirements: Prior to application for Discharge Permit, the

following shall be secured:
1. Environmental Compliance Certificate (ECC) or Certificate of Non-Coverage
2. Application Form from DENR or LLDA
3. Designated and Accredited Pollution Control Officer (PCO
- Curriculum Vitae
- Undergo 40 hours accreditation training course by DENR or LLDA
4. Working Plan signed by Professional Mechanical Engineer (PME)
5. Engineers Report
6. Submission of Quarterly Self-Monitoring Report to LLDA
Location of the treatment and disposal facility: Under the latest Fire Code of the
Philippines, underground or basement WTP must be avoided for the following
reasons:
1. Possible accumulation of methane gas during breakdown
2. Difficult to access, thus delaying the response during emergency
3. Risk on the part of the full time WTP operator due to the poor indoor air
quality in basements
Space Availability: This determines the technology/type or treatment given the
volume and characteristic of wastewater. Smaller space available requires a
more compact type of WTP.
Infrastructure Requirements: Generally upon construction, WTP chambers shall
be water proofed and can withstand pressure of air blowers and pumping during
operation. It is necessary to provide an air vent in air diffusers to avoid fatigue
of the blower component. Proper ventilation and lighting illumination are also
necessary. Proper warning and signage in strategic areas must be provided.
Locally available equipment and parts: In selecting WTP technology, the Terms
of Reference (TOR), should include the criteria that the equipment parts must be
readily available in the local market for at least five (5) years. This will ensure
that there will be a supply of equipment parts in cases when repairs are needed.
Treatment Efficiency: The main objective of treating wastewater is to prevent
pollution and protect the receiving body of water. This can be achieved by
maintaining treatment efficiency that meets the DENR/EMB/LLDA effluent
standards.
Quantity of Wastewater for Treatment and Disposal: The influent of wastewater
for treatment and disposal depends on the day to day consumption of water.
Reuse of Treated Wastewater: Treated wastewater can be used for cooling towers,
watering of ornamental plants and trees, cleaning of hospital buildings and grounds
92
and for flushing of urinals and toilets. Separate piping for toilets is necessary
in using treated wastewater. By using treated wastewater, over extraction of
ground water and preserved water resources can be prevented.
Characteristic of Wastewater for Treatment: In order to select the best technology
option, there is need to know the characteristics of the HCFs wastewater through
water analysis.
Sludge and Septage Disposal: Disposal of accumulated sludge and septage shall
be included in the selection of WTP technology in compliance with the IRR
of Chapter 17 of PD856 and the Operational Manual on Sludge and Septage
Treatment.
Operation and Maintenance: It is important to hire a WTP Operator or a service
provider for the efficient operation and maintenance, monitoring and recording
of parameters. It is a must to have a readily available consumable stock of
needed equipment and treatment materials for continuous WTP operation.
Training Requirement for Operation: It is the responsibility of the awarded
contractor to conduct the on-site or off-site training for the service, operation
and proper preventive maintenance of the WTP. In compliance with the DENR
requirements, the WTP operator shall undergo training before renewal of the
discharge permit. A newly hired or newly assigned operator must first undergo
training with the DENR.
Investment and Operating Cost: Since it is a mandatory requirement of
the government, the management of the HCF shall allocate a budget for the
acquisition and maintenance of the WTP. Maintenance cost, manpower and
operational (electrical and water) costs of the WTP shall be included in the
annual budget of the HCF.
For a comparison of the Advantages and Disadvantages of the Different Types of

WTPs please refer to Annex G.
93
MANUAL ON
MANUAL ONHEALTHCARE
HEALTHCAREWASTE MANAGEMENT,
WASTE THIRDTHIRD
MANAGEMENT, EDITION
EDITION
Central STP Body of Water
HCF
Departments
On-site STP Body of Water
Pre-Treatment
Specific STP
Figure 7.2 Flow of Wastewater from HCF Departments to WTP
Pre- Primary
Liquid Secondary Tertiary
Treat- Treat-
Treatment Treatment
Waste ment ment
Sludge Effluent
Treatment
Recycle
(may be
Disposal used for
(may be Municipal
gardening,
used as drainage
toilet,
fertilizer) cooling
towers)
Figure 7.3 Flow of Wastewater within the WTP
94
94
7.7 Operation, Maintenance and Monitoring of the WTP

7.7.1 Operation and Maintenance
The following elements must be in place for the efficient and effective operation
and maintenance of the WTP system:
Awareness among the management and senior staff on wastewater problems;

Physical Assent Management (PAM) and Preventive Maintenance Program
(PMP);
Basic tools to carry out regular maintenance;
PPE and other safety equipment measures;
Trained operators and workers;
Budget for operational costs and regular maintenance
The management shall designate wastewater treatment operator who will be

responsible for the operation and maintenance of the WTP. A maintenance plan which
includes corrective as well as preventive maintenance shall be set up for the collection,
pre-treatment and treatment of wastewater.
7.7.2 Wastewater Quality Monitoring

If an on-site treatment plant is operated, regular testing of the influent as well as
the effluent shall be monitored to test the efficiency of the treatment plant. Parameters
required by DENR AO No. 35 will be tested based on the prescribed frequency.
95
96
PART III
ADMINISTRATIVE
CONTROLS AND
REQUIREMENTS
98
ADMINISTRATIVE REQUIREMENTS
Chapter 8: Administrative Requirements

The success in the implementation of the HCWM depends on the political will
of the head of the organization and the motivation, dedication and commitment of
all the HCF workers. The planning, directing, implementing and review depend on
the capability of the designated members of the HCWM committee to sustain the
program. Appropriate HCWM practices depend largely on the administration and
organization and require adequate legislative and financial support as well as the
active participation by trained and informed staff.
8.1 Oversight and Management at the National and Local Levels

In the Joint Administrative Order of the DOH-DENR No. 2 Series of 2005,
specific duties and responsibilities have been indicated for the DENR through the
Environmental Management Bureau (EMB) and its regional offices, the National
Solid Waste Management Commission (NSWMC) and the DOH through its Center
for Health Development (CHD), Bureau of Health Devices and Technology (BHDT),
Environmental and Occupational Health Office (EOHO) of the National Center for
Disease Prevention and Control (NCDPC), the National Center for Health Facility
Development (NCHFD) and the National Reference Laboratory (NRL) East Avenue
Medical Center, Quezon City.
8.1.1 DENR
The DENR through the EMB and its regional offices shall:
Formulate and implement pertinent rules and regulations on the management
of healthcare waste in the Philippines, particularly concerning the issuance of
necessary permits and clearances for the Transport, Treatment, Storage and
Disposal of such wastes, as governed by PD 1586, RA 6969, RA 8749, RA 9275
and RA 9003;
Formulate policies, standards and guidelines on the transport, treatment, storage
and disposal of HCW;
Oversee compliance by generators, transporters, TSD facility operators and/or
final disposal facility operators with the proper transport, treatment, storage and
disposal of HCW;
Conduct regular sampling and monitoring of wastewater in HCFs and TSD
facilities to determine compliance with the provisions of RA 9275;
Require TSD facility operators and on-site treaters to present to the DENR copies
of the results of microbiological tests on the HCW treated using autoclave,
microwave, hydroclave and other disinfection facilities prior to the renewal of
their Permits under RA 6969;
Provide technical assistance and support to the advocacy programs on HCWM; and
99
Notify the DOH on cases of non-compliance or notice of violation issued to

HCF, institutions and establishments licensed by the DOH.
8.1.2 DOH
The DOH shall:
Include HCWM criteria in the licensing and accreditation requirements for
HCFs. Formulate policies, plans, standards, guidelines, systems and procedures
on the management of HCW;
Develop training programs and corresponding modules on HCWM;
Provide technical and resource mobilization to ensure an effective and efficient
implementation of HCWM program;
Require all HCW TSD facility operators and HCW generators with on-site waste
treatment facilities to use DOH-BHDT registered equipment or devices used for
the treatment of HCW;
Conduct regular performance evaluation of equipment/devices used for the
treatment of HCW by the DOH-BHDT;
Monitor the microbiological test of treated wastes to ensure compliance with
DOH standards;
Evaluate the HCFs compliance with proper HCWM program and provide
incentive program for compliant hospital and for best practices;
Issue Department Circulars to ensure that all environmental requirements are
complied with; and
Notify the DENR on actions taken on cases of non-compliance or notice of
violation issued to HCF, institutions and business establishments.
8.1.3 DOH Centers for Health Development

The DOH Centers for Health Development shall:
Advocate HCWM practices to the Local Chief Executives, key leaders and other
stakeholders;
Monitor HCWM implementation and compliance of DOH-licensed HCF and
submit reports to DOH;
Provide technical assistance on HCWM through:
1. Training
2. Issuance of advisory on the preparation of HCWM plans as a requirement for
licensing or renewal thereof
3. Dissemination of policies, guidelines and information
4. Monitoring and validation of the implementation of HCWM
5. Development, reproduction and dissemination of HCWM IEC materials
6. Participation in any public hearing related to HCWM
100
8.1.4 Philippine Health Insurance Corporation (PHIC)

The Philippine Health Insurance Corporation (PHIC) and other accrediting bodies/
agencies shall incorporate the following in the core indicator requirements for HCFs
to qualify as Center of Safety, Center of Quality and/or Center for Excellence:
HCWM Plan being implemented and monitored within the HCF;

Functional organized and established HCWM Committee;
Proper waste management segregation and compliance to color-coding;
On-site or off-site treatment disposal;
Updated discharge permit;
Waste generator ID
Adequate signage in place for HCW deposition and other established criteria for
an HCF to meet the standards for safety, quality and excellence.
8.1.5 Department of Interior and Local Government (DILG)

The Department of Interior and Local Government (DILG) through the different
Local Government Units (LGU) shall:
Monitor the compliance of HCFs under its jurisdiction on the proper waste
management, segregation and disposal
Provide assistance in the provision of an appropriate landfill, collection of waste
and installation of the WTP within the municipality
Ensure HCFs compliance with mandatory requirements for the transport,
treatment storage and disposal of HCW as governed by PD 1586, RA 6969, RA
8749, RA 9275 and RA 9003.
8.2 Administrative Requirements at the Healthcare Facility

The HCF has to comply with certain administrative requirements for a functional
HCWM. Discussed in succeeding topics are the mandatory requirements needed to
make the HCF compliant.
8.2.1 Organization and Functions

The entire organization of the HCF must be responsible for the proper segregation,
collection, storage, treatment and disposal of waste generated by the facility. However,
there are certain units and individuals in the HCF that usually have more responsibility
relative to HCWM. To sustain the implementation of HCWM within the HCF, the
Office of the Administrator and/or Head of the HCF shall have the following duties
and responsibilities and ensure the following:
Organization of a Healthcare Waste Management Committee (HCWMC) that is
fully represented by all medical, nursing and administrative services in the HCF;
101
Designation / appointment of a Waste Management Officer (WMO) or its

Designation
equivalent /Pollution
appointment
Controlof Officer
a Waste (PCO)Management
to superviseOfficer (WMO) or
and coordinate the its
equivalent Pollution Control Officer (PCO)
HCWM planning and its subsequent implementation; to supervise and coordinate the HCWM
planning and itshealthcare
An up-dated subsequentwaste
implementation;
management plan (HCWMP) that incorporates
Anmonitoring
up-dated procedures;
healthcare waste management plan (HCWMP) that incorporates
monitoring
Allocationprocedures;
of sufficient financial and personnel resources to ensure effective and
efficient implementation
Allocation of the HCWMP;
of sufficient financial and personnel resources to ensure effective and
efficient
Appointment
implementation of the HCWMP; members in the event of personnel
/ designation of alternative
leaving
Appointment key/ positions
designation in of
thealternative
HCWMCmembers or temporarily assignofresponsibility
in the event to
personnel leaving
another staff member until another one can be formally appointed/designated;
key positions in the HCWMC or temporarily assign responsibility to another staff
member
Adequate training for key members and designate the staff responsible for
until another one can be formally appointed/designated;
coordinating and implementing training courses;
Adequate training for key members and designate the staff responsible for
Speedy resolution of complaints and other related legal matters;
coordinating and implementing training courses;
Good working relationship with other related agencies by proper referral,
Speedy
consultation andofcooperation
resolution complaintsconcerning
and other related
HCWM. legal matters;
Good working relationship with other related agencies by proper referral,
consultation
8.2.2 Healthcare andWaste
cooperation concerning
Management HCWM.
Committee
Appointment or designation of specific committee to handle HCWM in the hospital
8.2.2 Healthcare
is critical Waste
on the part ofManagement Committee
the Administrator or head of the HCF. The qualification
Appointment or designation of specific
and political will of the person to be designatedcommitteewould
to handle HCWM
determine the in the hospital
success of the is
program.
critical on the part of the Administrator or head of the HCF. The qualification and
political will of the person to be designated would determine the success of the program.
Figure 8.1 illustrates the link between the designated WMO with the other key
Figure 8.1 illustrates
personnel of the HCF. the link between the designated WMO with the other key personnel
of the HCF.
HCF ADMINISTRATOR
Hospital Engineer
Head of Environmental Infection
Services Control Officer
Division Heads: Finance / Budget Officer

Medical Waste
Nursing Management
Administrative Officer
(WMO)
Senior Nursing Officer
Department Heads
Supply Officer
Medical and Dental Pollution Control Officer
Engineering
Pharmacy
Radiology
Laboratory
Blood Bank Ward Nurses and
Nutrition and Dietetics Medical Assistants
LEGEND:
Housekeeping
Internal Transportation System Coordinating to
Core Member
Hospital Attendants, Ancillary workers, waste handlers and support staff
Figure 8.1 Linkages of Key Personnel Involved in Healthcare Waste Management

Figure 8.1 Linkages of Key Personnel Involved in Healthcare Waste Management
102
102
All HCFs are required to have a HCWMC. However, small HCFs with limited staff
are required to have an appointed WMO.
The HCWMC shall be responsible for the following functions:
Formulate a policy formalizing the commitment of the HCF to proper

management of its waste with the goal of protecting health and the environment.
Establish baseline data and develop the HCFs HCWMP which shall include a
minimization plan, training and written guidelines on waste management.
Implement the HCWMP; review and update the policy, plans and guidelines on
an annual basis.
Ensure adequate financial and human resources for implementation of the
HCWMP.
Conduct regular committee meeting and submit minutes of meeting.
Regularly monitor and evaluate the efficiency and effectiveness of the HCWMP.
Ensure strict compliance with existing laws, policies and guidelines.
The HCWMC shall be composed of at least a minimum of five (5) members as the
Core Team to be composed of:
The chairperson shall be the Head/Administrator of the HCF who will oversee
the implementation and monitoring of the HCWMP in the HCF and imposition
of possible administrative sanctions for any deficiencies and/or violation
committed in the process;
The WMO to be appointed or designated shall be third ranking plantilla position
in the HCF. He/she shall be the alter ego of the Chairperson in the implementation
of the HCWMP within the HCF;
Infection Control Officer to be appointed or designated shall be at least a
supervising nurse level with appropriate training on infection control principles;
Pollution Control Officer to be appointed or designated shall be at least a
permanent HCF worker preferably an engineer who had undergone proper
training on pollution control principles;
Finance/Budget Officer and Supply Officer who are in-charge of preparing
annual plan for HCF operation to ensure the continuity of logistic requirements
in the implementation of the program.
The Core Team shall be responsible for the following duties and responsibilities:
Organize and establish the HCWM sub-committees or group who will directly
implement within specific units of the HCF the HCWM policies and guidelines;
Prepare the budgetary plan for the logistic requirements to implement HCWM
within the HCF;
103
Formulate policies and guidelines in the implementation of HCWM including

granting of incentives for best practices;
Approve request for unit activities and programs which will include training;
Provide assistance to all units relative to proper orientation of all staff;
Document and prepare report on regular basis; and
Perform specific duties and responsibilities as follows:
1. Administrator of the HCF designated as Chairperson of the HCWMC shall

be responsible in ensuring that the HCW shall be managed in accordance with
the national policies and guidelines; formally appoint/designate dedicated
personnel as WMO, PCO and other core members of the HCWMC indicating
the specific duties and responsibilities, including their accountabilities; directs
and controls the implementation of the different programs and activities of
the HCWMC and conducts regular review of the policies subject for revision
and assessment.
2. Waste Management Officer (WMO) designated as Co-Chair of the HCWMC
will be responsible for the day to day operation and monitoring of the waste
management system in the hospital. The WMO is directly responsible to
the Head/Administrator of the HCF. He or she shall establish linkage with
the Infection Control Officer, the Chief Pharmacist and the Radiation Officer
in order to become familiar with the correct procedures for handling and
disposing of pathological, pharmaceutical, chemical and radioactive waste.
The duties and responsibilities of the WMO shall include the following:
Ensure that the internal regular collection of waste observe the proper
waste segregation, collection and transport policies and guidelines;
Observe and direct the provision of continuous availability of waste bins,
plastic liners, personal protective equipment and collection bins/carts and
direct supervision of collection crews;
Check and direct correct use of central storage facility, which shall be kept
locked but accessible to authorized staff at all times;
Coordinate and monitor waste treatment, disposal operations, waste
transport for both on-site and off-site;
Coordinate with the Senior Nursing Officer and Department Heads to
ensure that nursing staff and medical assistants as well as doctors and other
qualified clinical staff are aware of their responsibilities for segregation
and storage of waste; and
Ensure that written emergency procedures are available and that personnel
are aware of the action to be taken in the event of an emergency. Investigate
and review reported incidents concerning the handling of HCW.
104
3. Designated Pollution Control Officer (PCO) shall be responsible for the

HCF compliance to the requirements mandated by EMB-DENR and other
regulatory agencies. He/she shall be responsible for the following duties
and responsibilities:
Attend to requirements of the HCF prior to the construction or installation
of pollution control facilities including the application and securing of
necessary pollution permits and renewal;
Monitor activities pertaining to the installation or construction of
pollution source and control facilities with the end in view of ensuring
their compliance with air, noise and water quality standards; the PCO
and the head of the HCF shall be held responsible for any violations of
PD 984 and its implementing rules and regulations committed by the
establishment where the officer is employed;
Supervise the proper operation and maintenance of pollution control
facilities of the establishment or agency;
Report within reasonable time to the EMB-DENR the breakdown of any
pollution control facility and the estimated and actual date of completion/
repair and operation;
Promptly submit validated/certified as correct by the HCF Administrator
periodic reports as required by the EMB-DENR;
Act as liaison officer and maintain linkage with the DOH, DENR, EMB
and designated PCO of other agencies including the local government
unit;
Keep himself abreast with the requirements of DENR-EMB and the
latest available technology on the prevention, control and abatement of
pollution; and
Attend the meetings for PCOs which may from time to time be called
by the monitoring agency.
4. Designated / Appointed Infection Control Officer (ICO) / Safety Officer
(SO) shall be responsible for the following duties and responsibilities:
Maintain linkage with the WMO on a continuous basis and provide
advice concerning the control of infection and the standards of the waste
disposal system.
Identify training requirements according to staff grade and occupation;
Organize and supervise staff training courses on safe waste management;
Liaise with the department heads and Senior Nursing Officer regarding
the training of their staff;
Handle the overall responsibility for chemical disinfection, sound
management of chemical stores and chemical waste minimization;
Ensure that all chemical used in the HCF has a Material Safety Data
Sheet (MSDS).
105
5. Finance / Budget Officer and Supply Officer

Finance/Budget Officer shall be responsible in assuring the provision of
continuous logistics, maintaining and sustaining the programs and activities of
the HCWM Committee and including them in the annual procurement plan.
Supply Officer shall:
Liaise with the WMO to ensure a continuous supply of the items required for
waste management (plastic liners and bins of the right specifications, spare
parts for the on-site waste treatment equipment, etc.). These items shall be
ordered within a reasonable time to ensure that these are readily available at
the HCF at all times. However, excessive accumulation of these items should
be avoided.
Investigate the possibility of purchasing environmental-friendly products
(e.g. PVC-free plastic items) by adopting the principles of Green Procurement
Policy.
All HCF management and support staff play a vital part in the success of the
program. Equally important are the specific roles and contribution of the following
specific key personnel in any HCF:
1. Division Heads of the Medical, Nursing and Administrative Services shall:

Ensure strict compliance of their respective staff with the policies and guidelines
being implemented by the HCWMC;
Disseminate polices and guidelines down the line including all the support staff
in the HCF;
Conduct regular orientation and reorientation among their HCF workers;
Maintain linkage with designated WMO
2. Department Heads are responsible within their respective areas of concern to ensure
that all members of their department are aware of the hospital waste management
plan as to segregation and storage procedures and that strict compliance is observed.
They shall also:
Ensure that all doctors, nurses, clinical and non-clinical professional staff in their
departments are aware of the segregation and storage procedures and that all
personnel comply with the highest standards in HCWM;
Liaise with the WMO to monitor working practices against failures or mistakes;
Ensure that key staff members in their department are given training in waste
segregation and disposal procedures; and
Encourage medical and nursing staff to be vigilant so as to ensure that hospital
attendants and ancillary staff follow correct procedures at all times.
3. The Senior Nursing Officer is responsible for the training of the nursing staff,
medical assistants, hospital attendants and ancillary staff on the correct procedures
for the segregation, storage, transport and disposal of waste. He/she shall:
106
Liaise with the WMO and the advisers (Infection Control Officer, Chief
Pharmacist, and Radiation Officer) to maintain the highest standards in HCWM;
Participate in staff introduction to and continuous training in the handling and
disposal of waste; and
Liaise with the Department Heads to ensure coordination of training activities,
other waste management issues specific to particular departments.
4. The Chief Pharmacist is responsible for the sound management of pharmaceutical
storage and for pharmaceutical waste minimization. Hs/she shall:
Liaise with the Department Heads, the WMO, the Senior Nursing Officer and
give advice, in accordance with the national policy and guidelines, on the
appropriate procedures for pharmaceutical waste disposal;
Coordinate continuous monitoring of compliance with procedures for the storage
and disposal of pharmaceutical waste;
Ensure that personnel involved in pharmaceutical waste handling and disposal
receive adequate training; and
Ensure safe utilization of genotoxic products and safe management of genotoxic
waste.
5. The Radiation Officer shall
Ensure proper waste management of radioactive waste;
Liaise with the Department Heads, the WMO, the Senior Nursing Officer and
give advice, in accordance with the national policy and guidelines, on the
appropriate procedures for radioactive waste disposal including its continuous
monitoring;
Ensure that personnel involved in radioactive waste handling and disposal
receive adequate training.
6. The Head of the General Services including the unit heads of housekeeping and
janitorial services shall:
Maintain cleanliness and orderliness of the HCF premises for aesthetic reasons;
Assist in the preparation of the HCWMP;
Initiate a sanitary manner of implementing the pre-treatment process, appropriate
collection system/procedures and disposal of waste either by TSD or municipal
system;
Establish baseline data, ensure generation of data for regular recording and
monitoring; and maintain proper filing system and update program records;
Maintain constant good working relationship with all HCF workers for their
support and full participation in implementing the program;
Enhance or provide continuous training for housekeeping/janitorial services on
waste management and government policies.
7. Maintenance and Ground Services shall:
Assist in the proper collection, pre-treatment and disposal of HCW;
107
Carry out directly the activities related to the operation and maintenance of
pre-treatment, collection and disposal system with importance to the drainage
system and plumbing facilities of the establishment;
Attend immediately to problems arising from the repair/installation of waste
equipment.
8. The Motor Pool and Ground Services shall
Assist in the provision of vehicle for transporting HCW to transfer station or
disposal sites;
Prepare and plan the collection system routes and frequency of collection of
HCW;
Inspect and schedule maintenance work on vehicles used for transporting HCW;
Observe proper infection control measures in the maintenance of vehicles used
for the transportation of HCW
9. The HCF Engineer or the designated in-charge of engineering services shall:
Be responsible for installing and maintaining waste storage facilities and comply
with the specifications of the national guidelines;
Be accountable for the adequate operation and maintenance of any on-site waste
treatment equipment;
Be responsible for compliance with mandatory requirements of pollution
control;
Be responsible for the staff involved in waste treatment; ensure that the staff
designated to operate the on-site waste treatment facilities are trained in their
operation and maintenance.
However, for other HCF, the composition may vary depending on the category and
availability of personnel. The Administrator of HCF shall formally appoint/designate
the members of the HCWMC indicating their specific duties and responsibilities.
8.2.3 Healthcare Waste Management Plan

A comprehensive HCWMP is the key ingredient to a successful waste management
within an HCF. It is important that the plan be understood or followed to be of great
value to the organization. Training of staff to ensure that they are familiar with and
understand the plan is critical to its successful implementation and the effective
handling of HCWs.
The HCWM plan shall consider three major concerns. Specific plan of actions
shall be formulated to respond to each concern which shall include in its performance
indicators the involvement of all HCF personnel and its clients; improvement of HCF
facilities; training and enhancement of skills necessary to have an effective handling
of HCW.
In developing a comprehensive HCWMP, the following major concerns shall be
addressed:
1. Assessment of waste generation and waste disposal. In developing a HCWMP, the
HCWMC needs to make an assessment of all waste generated in the HCF. The WMO
108
shall be responsible for coordinating such a survey and for the analysis of the results.
The assessment shall include:
Average daily volume of waste generated per category within a given period of
time;
Site and location of the HCF vis a vis the existence of accredited TSD within the
locality;
Assessment of any future changes in the facility, departmental growth or the
establishment of new departments. Data from the waste generation survey shall
be a basis of the waste management plan.
2. Review of existing HCWM policies and procedures being implemented. To
have a clear overview of this concern, the following activities have to be included
in the plan, namely:
Understanding of existing policies, laws and regulations related to HCWM;
Review of the present waste management system to include where the waste is
generated, what types of waste are being generated, how and where it is stored
and the cost effectiveness of the current handling processes; and
Revision and redesigning of the HCWMP to ensure that all issues have been
addressed.
3. Formulation and drafting of HCWMP
In the drafting and formulation of the HCWMP, the following may be used as
guide:
a. Short description of the plan and the HCF. This will include the background
of the HCF including its mandates, type of clients being served, demographic
profile and geographic location of the HCF. This will also discuss briefly the
different national, local and international laws, policies and issuances relevant
to the implementation of HCWM within the HCF.
b. Objective and rationale of the plan this will briefly discuss the purpose of the
plan, targets, its coverage, scope and limitations.
c. Composition of HCWMC, its structure, duties and responsibilities; roles and
responsibilities of the other staff of the HCF.
d. HCWM plan from point of generation up to its final disposal including flow
chart, route plans and schedules. This will also identify the different activities
and persons responsible for handling specific activities and whom to be
responsible for. This will also include the milestones or strategies to move the
current HCWM system into the system envisioned in the plan, the minimization
plan, the procurement plan and others.
e. Education, training, information and communication activities a comprehensive
training and orientation of HCF worker shall be conducted. Each HCF staff must
know their specific roles in the effective implementation of the HCWMP. Every
HCF worker must be aware of the policy, the significant health and environmental
impacts of their work activities, their roles and responsibilities, the procedures that
109
apply to their work and the importance of conforming with the requirements
as well as the consequences of not following the requirements. The plan will
identify the timetable and the responsible persons for the development of
training materials and conduct training for the different categories of HCFs, the
development of advocacy materials (if needed) and the conduct of orientation
for patients and watchers.
f. HCF worker protection and safety this will include the plans for HCF workers
occupational health and safety program including emergency management for
possible related risks or accidents during the process. This will also indicate
the Infection Control policies and procedures to be observed in handling HCW
specifically infectious and mercury waste,
g. Monitoring and evaluation action plan for the conduct of regular monitoring of
the implementation and submission of required reports. This will include the self-
monitoring tools, assessment of findings and submission of recommendations
and follow-up of status.
h. Financial Requirements for the implementation of the plan
i. Provision for feedback mechanism, updating and revision of plan.
The HCWMP basic components as discussed may vary depending on the level and
capability of the HCF.
8.2.4 Life Cycle Analysis (LCA)

One of the approaches that can be helpful in developing a HCWMP is the
Life Cycle Analysis (LCA). LCA is a cradle to grave approach to estimate the
cumulative environmental impacts associated with the life cycle (manufacture, use
and maintenance to its final disposal) of a product, process or service by:
Compiling and inventory of relevant energy and material inputs and

environmental releases
Evaluating the potential environmental impacts associated with identified inputs
and releases
Interpreting the results to help decision-makers make a more informed decision.
LCA provides a more accurate picture of the true environmental trade-offs in

product and process selection. An LCA can help decision-makers select the product
or process that result in the least impact to the environment. This information can
be used with other factors, such as cost and performance data to select a product or
process. LCA data identifies the transfer of environmental impacts from one media to
another (e.g. eliminating air emissions by creating a wastewater effluent instead) and/
or from one life cycle stage to another (e.g. form use to reuse of the product to the raw
material acquisition phase).
110
This ability to track and document shifts in environmental impacts can help decision
makers and managers fully characterize the environmental trade-offs associated with
product or process alternatives. By performing an LCA, analysts can:
Develop a systematic evaluation of the environmental consequences associated
with given product.
Analyse the environmental trade-offs associated with one or more specific
products/processes to help gain stakeholder (state, community, etc.) acceptance
for planned action.
Quantify environmental releases to air, water and land in relation to each life
cycle stage and/or contributing process.
Assist the human and ecological effects of material consumption and
environmental releases to the local community, region and the world.
Compare the health and ecological impacts between two or more rival products/
processes or identify the impacts of a specific product or process.
Identify impacts to one or more specific environmental area of concern.
Figure 8.2 Life Cycle Stages

Source: EPA, 1993-SAIC 2006
8.2.5 Environmental Management System (ISO 14001)

Another approach that can be adopted particularly those aiming for an ISO
accreditation is the development of an Environmental Management System as
implemented under the ISO 14001.
An Environmental Management System (EMS) is a continuous process of
improvement which involves environmental planning, implementation, checking
and management review on the programs being implemented within the HCF in
compliance with existing environmental and HCWM laws and policies.
111
An EMS follows a Plan-Do-Check-Act Cycle or PDCA. The diagram shows

the process of first developing an environmental policy, planning the EMS and
the implementation. The process also includes checking the system and acting
on it. Constant review and revision by the organization is vital for the continuous
improvement of the EMS.
Figure 8.3The Environmental Management System (EMS) Cycle
8.2.5.1 Key Elements of the EMS

The following are the key elements of the EMS cycle:
Policy Statement a statement of the organizations commitment to the
environment
Identification of Significant Environmental Impacts environmental
attributes of products, activities and services; and their effects on the environment
Development of Objectives and Targets environmental goals for the
organization
Implementation plans to meet objectives and targets
Training instruction to ensure HCF workers are aware and capable of fulfilling
their environmental responsibilities
Management Review
The EMS can be integrated with the HCWM plans and activities being implemented
by the HCF. It is flexible and does not necessarily require organizations to retool
their existing activities. An EMS establishes a management framework by which an
112
organizations impact on the environment can be systematically identified and reduced.

For example, many organizations, including cities and municipalities, have active and
effective pollution prevention activities underway; these could be incorporated into
the overall EMS.
8.2.5.2 Benefits of the EMS

Adopting an EMS:
Serves as a tool to improve performance
Provides a systematic way of managing an organizations environmental affairs
Addresses the organizations overall management structure for the immediate
and long-term impacts of its products, services and processes on the environment
Gives order and consistency for organizations to address environmental concerns
through the allocation of resources, assignment of responsibility and on-going
evaluation of practices, procedures and processes
Focuses on continuous improvement of the system
Application of the EMS in the system will provide benefits which include cost
reductions through reduced energy consumption, waste and recycling, minimizing
other negative impacts on the environment, and even improved public image.
The EMS framework encompasses the environmental aspects of waste including
reduction, reuse and recycling. It also has considerable relevance to environmentally
preferable purchasing; the HCF has a choice with regards to the purchase of products
or services. It is becoming increasingly common that HCFs require suppliers to have
an EMS in place.
8.2.6 Monitoring and Evaluation of the HCWM Plan

To validate the effectiveness and the efficiency of the HCWMP , regular monitoring
and evaluation is necessary. There are several methods which can be adapted to
document the assessment and evaluation of the program. This includes using the
designated tools such as Self-Monitoring Sheet (for samples, please refer to Annex C
and D). By doing self-monitoring, it will be possible to grade the actual success of the
Plan for every unit of the HCF.
The six major parameters that will be used to determine the extent of the Plan
implementation are the following:
1. Waste Minimization Practices
2. Waste Segregation
3. Waste On-Site Collection, Transport and Disposal
4. Waste Treatment On-Site (if applicable)
5. Wastewater Management
6. Administrative Control
113
In Table 8.1, the necessary forms needed to be submitted by the HCF are listed
alongside with the on-line links where the forms can be downloaded from.
Table 8.1 List of Necessary Forms to be Submitted by the HCF
FORMS NEEDED Links

Environmental Compliance Certificate h t t p : / / e i a . e m b . g o v. p h / i n d e x .
(ECC) php?option=com_content&task=view&
id=56&Itemid=55
EMB Quarterly Self-Monitoring Report http://www.emb.gov.ph/laws/water%20
LLDA Clearance quality%20management/dao03-27-
FINAL%20manual%20SMR%20.pdf
LLDA Discharge Permit http://www.llda.gov.ph/dox/forms/
LLDAClearance.pdf
LLDA Self-Monitoring Report http://www.llda.gov.ph/dox/forms/
DischargePermit.pdf
Hazardous Waste Generator http://www.llda.gov.ph/dox/forms/
SelfMonitoringReport.pdf
Registration Form http://www.emb.gov.ph/hazardous/
Forms/RegForm_HWGenerator.PDF
Hazardous Waste Transporter http://www.emb.gov.ph/hazardous/
Registration Form Forms/RegiForm_HWTransporter.PDF
Hazardous Waste Treater Registration http://www.emb.gov.ph/hazardous/
Form Forms/RegForm_HWTreater.PDF
Hazardous Waste Generator Quarterly/ http://www.emb.gov.ph/hazardous/
Annual Report Form Quarterly%20Report%20Form.pdf
Hazardous Waste Transporter Checklist http://www.emb.gov.ph/hazardous/
Forms/Checklist_HWTransporter.PDF
Hazardous Waste Treater Checklist http://www.emb.gov.ph/hazardous/
Forms/Checklist_HWTreater.PDF
Hazardous Waste Transporter Affidavit http://www.emb.gov.ph/hazardous/
Forms/affidavit_HWtransporter.PDF
Hazardous Waste Treater Affidavit http://www.emb.gov.ph/hazardous/
Forms/affidavit_HWtreater.PDF
8.3 Communication and Training

All HCFs, the DOH and the EMB-DENR have the responsibility and a duty of
care for the environment and public health, particularly in the institutionalization of
awareness among HCW and the general public.
The need to promote appropriate handling and disposal of HCW is important to
public health. Every member of the HCF and the community has the right to be
informed about the potential health hazards associated with HCW. Inadequate handling
of HCW may have serious public health consequences and impacts on environmental
health protection.
114
Public awareness through formal or informal education plays an important role in

HCWM. Development of information, education and communication (IEC) programs
and materials shall be given due course.
The objectives are:
To transmit the basic skills and knowledge in establishing a healthy, secure and
safe environment for HCW and the general public.
To inform the public about the risks linked to HCW, focusing on people either
living or working in close proximity to, or visiting HCF, families of patients
being treated at home and scavengers on waste dumps.
To foster responsibility among hospital patients and visitors to HCF regarding
hygiene and HCWM.
To prevent exposure to HCW and related health hazards, this exposure may be
voluntary in the case of scavengers or accidental as a consequence of unsafe
disposal methods.
To increase awareness of the impact of HCW on environment and ecology.
To influence behaviour of patients, watchers, HCF workers to implement proper
HCWM.
In developing the education, training, information and communication tools, there
are several concerns that need to be addressed. These are:
Specific targeted subjects or participants, including their level of understanding
and involvement in the implementation of the HCWMP;
Availability of funds and logistics to sustain the program;
Support of the HCF management to the program.
8.3.1 Methods of Communication and Training Used

To effectively communicate the importance of knowing the hazards of HCW and its
management to targeted participants, the following methods can be considered:
Graphics and audio-visuals which may be in the form of brochures, posters,
display boards, video tapes, slides, CD/DVDs, flyers, flip charts, leaflets, etc.
Use of tri-media such as announcements or commercial ads featured in radios,
movies, television, newspaper, magazines and the internet.
Orientation/re-orientation seminars, training and workshops; community and
health teachings for hospital patients, watchers and other clients using IEC
materials and didactic exercise.
Issuance of written HCF policies to disseminate the information and awareness
among HCF workers. There shall be corresponding sanctions to be implemented
for non-compliance with issued policies.
115
8.3.2 Training of Healthcare Workers

Training is essentially the transferring of knowledge, skills and capacity building of
targeted participants. In any HCF, it is mandatory to implement education and training
programs to make all the HCF workers aware of the hazards involved in HCW and
their specific roles.
All HCF workers shall receive training tailored to their different needs at various
levels or functions in the HCF. The overall aim of the training is to develop awareness
on the health, safety and environmental issues relating to HCW, and how these
can affect HCF workers in their daily work. It shall also highlight the roles and
responsibilities of the HCF workers.
Separate training activities shall be designed for each of the following targeted
categories of personnel:
HCF managers and administrative staff responsible for implementing regulations

on HCWM
Medical doctors
Nurses and assistant nurses
Cleaners, porters, auxiliary staff and waste handlers
The training for waste generators as well as waste handlers is equally important.
Medical doctors may be educated through senior staff workshops and general hospital
staff through formal seminars. The training of waste managers and regulators could
take place outside the hospital at public health schools or university departments.
Basic education program for HCF worker shall include:
Information on and justification for all aspects of the HCW policy;

Information on the role and responsibilities of each HCF worker in implementing
the policy;
Technical instructions, relevant for the target group, on the application of waste
management practices.
All HCF workers must receive initial and annual training. A trained individual
must be available during training sessions. The instructors shall have experience
in teaching and training, and be ideally familiar with the hazards and practices of
HCWM; they should also have experience in waste handling.
8.3.3 Suggested Training Package for Each Target Group

The development of a training package shall be suitable for the various types of HCFs,
including government, private and teaching hospitals; dental clinics, polyclinics, health
centers, healthcare research institutions, clinical laboratories and similar establishments.
116
8.3.3.1 For Personnel Providing Healthcare

The training course shall provide an overview of the waste management policy and
underlying rationale and information on practices relevant to trainees responsibilities.
Waste segregation is a key element for this training in waste management. All HCF
workers that generate HCW shall be responsible for its segregation, and shall therefore
receive training in the basic principles and practical applications of segregation.
Training shall make the staff aware of the potentially serious implications of the
mismanagement of waste to the health of waste handlers and patients; provide them
with an overview of the fate of waste after collection and removal from the ward and
teach them the importance of proper segregation.
8.3.3.2 For Waste Handlers

Topics covered may include the waste management policy, health hazards, on-site
transportation, storage, safety practices and emergency response. Among staffs who
routinely handle HCW, awareness of the need for safety may decrease with time, which
will increase the risk of injury. Periodic refresher course is therefore recommended.
8.3.3.3 For Healthcare Waste Management Operators

The training course shall include:
Information of the risk associated with the handling of HCW;
Procedures for dealing with spillage and other accidents;
Correct use of protective clothing.
8.3.3.4 For Staff who Transport the Waste

In carrying out the responsibility of waste transportation, the drivers and waste
handlers shall be aware of the nature and risk of the transported waste. Transport staff
shall be able to carry out all procedures for:
Handling, loading and unloading of waste bags and bins;
Dealing with spillage or accidents;
The use of PPE; and
Documentation and recording of HCW, e.g. by means of consignment note
system to allow waste to be traced from the point of collection to the final place
of disposal.
8.3.3.5 For Treatment Plant Operators

HCFs shall make arrangements to provide training to prospective treatment plant
operators specifically on the following areas:
General operations of the treatment facility;
Health, safety and environmental implications of treatment operations;
Technical procedures for plant operations;
117
Emergency response, in case of equipment failures and/or alarms;

Maintenance of the plant and record keeping;
Surveillance of the quality of emissions and discharges, according to the
specifications.
8.3.3.6 Orientation Module for Patients

HCF shall provide patients and watchers an orientation of the HCWM policies and
system of the hospital as part of the admission procedure. The orientation will include,
at the minimum, the following:
Policies on HCWM relevant to patients and watchers such as the ban on

Styrofoam and non-reusable plastic food containers, proper segregation of waste
Impact of improper segregation and Styrofoam/non-reusable plastic food
containers on health, safety and environment
Figure 8.4 IEC Material: Leaflet given to patient upon admission to hospital
118
8.4 Budgetary Requirements to Implement the HCWM Program

The benefits of HCWM are in terms of infection control, protection of HCF
workers, and the protection of the environment and the accreditation of the HCF with
the national social health insurance scheme or PhilHealth. To realize these benefits
and be compliant with the existing laws and policies, the HCF needs to identify the
most cost-effective option that fits its needs and financial capacities. This section will
provide guidance to HCF by looking at the costs elements of HCWM, identifying
measures to reduce costs and examining available options for financing.
8.4.1 Investment and Operations Cost

The polluter pays principle mandates each HCF to be financially liable for the
safe management of its HCW. The costs of separate collection, packaging and on-site
handling are internal to the establishment; while costs of off-site transport, treatment
and final disposal are external and paid to the contractors who provide the service. The
costs that will be incurred by the HCF in managing HCW will include:
8.4.1.1 Waste Segregation and On-Site Handling

Proper segregation and on-site handling of wastes includes the cost for the following
materials, goods and services:
Waste bins, color-coded plastic liners that shall be placed in appropriate locations
in the hospital, transport trolleys and collection bins.
Proper labels for the waste bins, tags for the plastic liners and signage/posters.
Training of personnel to place wastes in the appropriate containers and to handle
them in a safe manner
IEC materials
Storage spaces for HCW within the HCF, spill kits and measure to secure and
protect the wastes when needed.
PPE needed to safely and properly handle wastes
Occupational health and safety measures such as immunization
Sealer for plastic liners and packing the wastes for transport if the treatment
facility is located at a distance from the HCF
Transportation borne by the HCF
Operating and maintenance costs including salaries and wages
Segregation of wastes effectively reduces the amount of wastes needed for transport
(if located off-site), treatment and disposal at the treatment facility. Investments in
training and equipment may not be offset by lower costs. However, total costs to the
environment will diminish because the inclusion of materials that may release harmful
substances to the environment during treatment processes is lessened.
119
8.4.1.2 Waste Treatment

Establishing and operating an on-site waste treatment include the investment and
operating costs listed below:
Non-burn waste treatment technology and its accessories and related processes
(e.g. shredder and additional processes such as encapsulation and inertization
in cases where the waste treatment system do not deactivate chemical and toxic
agents)
Microbiological testing equipment and supplies
Installation and facility costs: installation labor, facility modifications cement
pad/s, curb cuts, sewers, electricity, space, security, etc.
Costs of pollution control equipment if required to control emissions and
effluents from the facility (e.g. wastewater treatment plant)
Construction of temporary storage and hauling areas for treated wastes
Direct labor costs: number of HCF workers needed to operate the treatment and
disposal equipment
Down time costs: including repair (parts and labor) and alternative treatment
Operating costs if the facility uses special chemicals and catalysts
Utility costs
Permitting and compliance fees: water and air monitoring fees, Environmental
Compliance Certificate (ECC), Discharge Permit, Permit to Operate Pollution
Source Equipment (e.g. generators) and registration with the DENR as waste
generator, treater and/or transporter
Fines: depending on permit requirements, national and local regulations;
violations of permits or emissions which may result to the payment of fines
All transportation, processing and tipping fees
Supply costs personal protective equipment, spill supplies, special bags (e.g.
some autoclaving systems require specific bags), collection containers (boxes or
reusable containers)
Community approval cost if a public hearing is required
Sterilization equipment
In cases where the HCF enters into a contract with a DENR-accredited TSD, the
costs that will be incurred by the HCF will be charges of the waste treater and the
associated transportation costs.
Investment in on-site treatment facilities may be costly but allows the HCF to
control the manner by which the waste is treated as well as the costs associated with
treatment. Off-site treatment facilities, when available, may be more costly in the long
run but it allows the HCF to concentrate on its basic occupational function and not on
operations it is not built to do, which is the treatment of waste.
120
8.4.1.3 Disposal
Disposal to a sanitary landfill is considerably more costly than disposal in open
dumpsites; sanitary landfills may charge a higher fee for waste coming from HCFs. In
evaluating treatment options, costs with relation to final disposal shall be considered
since treatment systems can almost eliminate wastes altogether (pyrolysis) but some
even increase the weight of wastes (steam systems without dryers). Care shall also be
taken to render the wastes unrecognizable. The following are some costs that should
be considered when using an on-site facility for the disposal of treated waste:
Construction of temporary storage and hauling areas for treated waste

Costs related to wastes not handled by the hauler
Cost of encapsulation, inertization, septic vault
Labor costs for hauling, labelling, waste documentation, security and
maintenance of temporary storage areas
Hauling costs
Transport containers
Landfill tipping fees
The WHO prepared two (2) costing tools, the Costing Analysis Tool (CAT) and
the Expanded Costing Analysis Tool (ECAT) to help calculate the true cost of setting
up an HCWM system. The CAT estimates the costs of HCWM at the national and
HCF levels. The ECAT, which is a modified version of the CAT, estimates costs at
the HCF, central treatment facility or cluster and national levels. These tools may be
downloaded from http://www.healthcarewaste.org/en/documents.html?id=218
8.4.2 Measures to Reduce Costs

In the long run, cost reductions can be achieved by implementing the following
measures at the different stages in the management of wastes:
1. Comprehensive Planning
Development and implementation of a comprehensive HCWMP which includes
the recommendations below on on-site management
Designing all elements of the system to be of adequate capacity in order to
obviate the need for subsequent costly modifications
Anticipating future trends in waste production and the likelihood of legislation
becoming more stringent
Planning collection and transport in such a way that all operations are safe and
cost-efficient
Possible cooperative use of regional waste treatment facilities, including private
sector facilities when appropriate
Establishment of wastewater disposal plan
121
2. On-site Management (source reduction, recycling and re-use)

Comprehensive management of chemicals and pharmaceuticals stores, which
includes centralized purchase and use of chemicals and pharmaceuticals; and the
centralized monitoring of chemical flows within the HCF.
Improved waste identification to simplify segregation, treatment and recycling
Reduction of the amount of material used to accomplish tasks. Examples are
the use of email instead of paper and the use of smaller amounts of disinfectant
to clean rooms.
Reduction of toxicity of the materials used in order to reduce the disposal costs
and the hazards to the HCF workers. Purchase of materials that may be reused
and recycled such as in the case of disposable medical care items and reusable
salad plates for the hospital cafeteria
Practice just in time delivery in order to minimize on wastes incurred due to the
expiry of items like drugs and chemicals
Adequate segregation of waste to avoid costly or inadequate treatment of waste
that does not require it.
3. Adequate treatment and disposal method
Selection of a treatment and disposal option that is appropriate for waste type
and local circumstances.
Use of treatment equipment appropriate type and capacity.
Possible cooperation between local HCFs
4. Measures at worker level
Establishment of training programs for HCF workers to improve the quality and
quantity of work
Protection of HCF workers against occupational risks
5. Documentation
Documentation of waste management and assessment of the true costs makes
it easier to identify priorities for cost reduction and to monitor progress in the
achievement of objectives.
8.4.3 Options for Financing

HCWM may be financed through in-house funds of the HCF, revenues from
recyclable waste, loans from credit facilities and through sub-contracting, partnerships
or joint-venture with other institutions providing TSD services (sharing WTP, waste
treatment, mercury storage).
Government-owned or private HCF may use internal revenues to pay for the cost of
the HCWM system. The costs of managing HCW shall be covered by a separate budget
line item in the HCF budget. In case in-house funds are not available, HCF and TSD
facilities can avail of credit financing for the investment and operation costs of HCW
treatment, wastewater treatment and air pollution control devices from loan facilities
122
such as the Environmental Infrastructure Support Credit Program (EISCP) of the

Development Bank of the Philippines (DBP).
Privatization is a method of financing various types of public works, including
HCWM. Under such an arrangement a private entity finances, designs, builds, owns
and operates the treatment facilities and sells its collection and disposal services to
government and private HCF. Privatization is an option that may be considered under
the following conditions:
Inability of hospitals to raise the needed capital

Expected greater efficiency in the private sector because of fewer constraints
than in the public sector (e.g. greater flexibility in purchasing and personnel
policies, allowing for more rapid adaptation to changing needs)
Transfer of responsibility for proper operation and maintenance to an organization
with more resources for minimizing risk.
In contracting with the private sector, the agreement between the private operator
and the HCF shall include agreements on the following issues:
Minimum risk level of service, especially with regards to reliability, safety,

public health risk and future expansions;
Future increases in cost resulting from factors that cannot be fully assessed at the
outset;
Environmental concerns;
Future transfer of ownership of the facilities;
Regular inspection and regulatory control.
123
Chapter 9: Health and Safety Practices

9.1 Principles
HCWM policies, plans and programs shall include provision for the health and
safety of HCF workers. Educating the HCF workers on the risks associated with
HCW shall be part of this policy. Established policies and procedures ensuring the
health and safety of HCF workers during the management of HCW from generation,
segregation, collection, transport, storage, treatment and disposal shall be consistently
implemented and complied by all concerned.
In a setting like an HCF, it takes team effort to have an effective HCWMP, as wastes
are generated and produced in different areas with interconnected work processes.
The support of the top management including the Administrator of the HCF is very
vital in ensuring that the program is established, implemented, monitored, evaluated
and continually improved. Essential occupational health and safety measures include:
Education, training and awareness of HCF workers

Provision of appropriate PPE
Establishment of an effective occupational health and safety program that
includes pre-employment immunization, pre and post exposure prophylactic
treatment, hazard identification and risk assessment and continuous medical
surveillance
Information, Education, and Communication (IEC) activities
9.2 Education, Training and Awareness of Healthcare Facility Workers

Everyone within the HCF plays a vital role in the management of HCW, for this
reason, the training program shall cast a wide network. Every HCF worker shall
be made aware of the policy, the significant health and environmental impacts of
their work activities, their roles and responsibilities, the procedure that apply to their
work and the importance of conformance with the requirements. The worker shall
understand the potential consequences of NOT following the requirements.
A training module shall be part of the Orientation/re-orientation Program for newly-
hired and existing workers to ensure consistency in compliance by all HCF workers.
The use of IEC materials, issuances and advisories shall be utilized to raise awareness
and ensure effective implementation of the program.
9.3 Workers Protection

All HCF workers who are directly involved in the handling of HCW must be
provided with adequate protection from the hazards associated with it. Protection
against personal injury is very important for all HCF workers at risk. The individual
responsible to the management of HCW shall ensure that all these risks are identified
and that suitable protection is provided. The installation of the required protection
measures will proceed after the conduct of a comprehensive risk assessment of the
124
HEALTH AND SAFETY PRACTICES
activities in HCWM. The design of the measure will focus on the prevention of
workers exposure or at least exposure within safe limits.
Suitable training shall be provided to the HCF workers on this aspect. In regular
cleaning of waste bins, HCF worker shall observe infection control measures.
9.4 Personal Protective Equipment (PPE)

PPE is a specialized clothing or equipment worn by a worker designed to protect
against infectious materials or form exposure to infectious agents (OSHA ) thus,
preventing injury or illness from specific hazards.
Every effort shall be made to eliminate it so that workers are not harmed or at
least lessen the risk of hazards associated in their work processes. It can be done by
considering the hierarchy of controls, that is elimination, substitution, engineering and
administrative controls. However, if this is not possible, the use of PPE is necessary.
PPE can also provide an added protection to the worker even if the hazard is being
controlled by other means.
HCWM program requires that the following PPE shall be made available to all HCF
workers who collect and handle HCW:
Figure 9.1 Personal Protective Equipment
125
Disposable gloves (for medical staff) or heavy duty gloves (for waste handlers)
obligatory
Face masks obligatory for waste handlers and for other HCF workers depending
on the nature of work and exposure
Hard hats with or without visor depending on the nature of work and exposure
Eye protectors / Safety goggle depending on the nature of work and exposure
Overalls (coveralls) depending on the nature of work and exposure
Industrial aprons depending on the nature of work and exposure
Leg protectors and/or industrial shoes/boots depending on the nature of work
and exposure
Respiratory (HEPA) filters depending on the nature of work and exposure
Ear muffs - depending on the nature of work and exposure
Industrial boots and heavy-duty gloves are particularly important for waste handlers.
If segregation is improper, needles or other sharp items may have been placed in
plastic bags, such items may also pierce thin-walled or weak plastic containers. The
thick soles of the boots offer protection in the storage area, as a precaution from spilled
sharps; and where floors are wet and slippery. Leg protectors may also be worn to
prevent HCW liners from coming in contact with the workers legs during handling.
HCF workers should know the correct usage and maintenance of the equipment.
PPE shall conform to established standards. Training on PPE shall include:
1. Description on the type of hazard and the condition of the work environment -
determination of waste management concerns, working conditions, materials,
equipment and substances used, the exposed populations and conditions of
exposure, taking into account the adverse effects on human health and to the
environment.
2. Explanation on why a certain type of PPE has been selected - based on the
hazards present, the type of materials used and the manner in which they will be
handled.
3. Explanation on its proper use, maintenance and storage - PPE shall be kept safe
and in good condition. Defective PPE shall be discarded. Since PPEs have
limitations and useful life, these must be regularly inspected for its effectiveness.
9.5 Occupational Health and Safety Program

9.5.1 Personal Hygiene
Handwashing with soap and water has been considered as a measure of personal
hygiene. Provision for washing facilities (with soap and warm water) and instruction
shall be made available at the point needed to ensure that proper handwashing is
observed. If clean running water is not accessible, use soap and available water. If
soap and water are unavailable, use an alcohol-based hand sanitizer that contains at
least 60% alcohol to clean hands. (CDC: Handwashing: Clean Hands Save Lives)
126
Hand hygiene is an essential component of an effective infection prevention and

control program. Good technique ensures that all surfaces of the hands come into
contact with decontaminating agent. This has been accepted for many years and is
acknowledged in current guidelines.
When should you wash your hands?

Before, during and after preparing food
Before eating
After using the toilet
After changing diapers or cleaning up a child who has used the toilet
Before and after caring for someone who is sick
After touching animal or animal waste
After touching garbage
Before and after treating a cut or wound
Bathing after a waste-related emergency shall be done for complete decontamination.
9.5.2 Immunization
1. Pre-employment Immunization
HCF workers shall be given immunization to prevent or ameliorate the effects
of infection by many pathogens such as virus causing hepatitis B and tetanus
infection.
Many HCF workers are at risk of exposure to and possible transmission of
vaccine-preventable diseases because of their contact with infectious materials
from patients such as HCW. Maintenance of immunity is therefore an essential
part of the prevention and infection control programs for HCF workers.
2. Post Prophylactic Immunization
Persons exposed to hazardous risk such as needle prick, splashing and other
work-related injury shall be given a post prophylactic immunization as prescribed
by the attending physician.
127
Figure 9.2 Procedures for Proper Handwashing

Source: http://www.who.int/gpsc/5may/How_To_HandWash_Poster.pdf
128
Figure 9.3 Procedures for Proper Handrubbing

Source: http://www.who.int/gpsc/5may/How_To_HandRub_Poster.pdf
129
9.6 Emergency Management Plan
As defined by the WHO contingency planning and emergency preparedness is a

program of long-term development activities whose goals are to strengthen the overall
capacity and capability of a country to manage efficiently all types of emergency
and to bring an orderly transition from relief through recovery and back to sustain
development.
Adopting the policy of WHO, there are three (3) phases for the safe management of
HCW in emergencies:
Phase One: Mitigation and Preparedness

Phase Two: Emergency Response
Phase Three: Recovery
9.6.1 Mitigation and Preparedness

As defined, mitigation refers to the systematic reduction in the extent of exposure to
a risk and/or the likelihood of its occurrence. On the other hand, preparedness refers to
the HCFs readiness to respond to any emergency. This includes the specific strategies,
plans and actions to respond to the occurrence of any hazard such as exposure to
hazardous substances, whether infectious, chemical and biological spillage and other
toxic substance. To determine the readiness of the HCF, the following activities shall
be done:
9.6.1.1 Rapid Initial Assessment This is the collection of subjective and objective
information to measure damage and identify those basic needs of the affected
population that require immediate response within 24 hours (DOH-HEMS, WHO
-WPRO 2007). An assessment team shall conduct this initial phase which may include
relief or awareness activities. To work effectively, the team shall have a clear cut
disposition and priority whether to gather information or perform relief actions.
Based on the assessment report, hazards due to waste shall be prioritized according
to the following elements:
1. Severity
2. Frequency
3. Extent
4. Duration
5. Manageability
9.6.1.2 Availability of first aid kit for use of injured workers. First aid kit shall contain
different-sized kits intended to serve groups of different sizes.
In general, the first aid kit required in a workplace varies depending on the size of
the facility and by the following factors:
130
The laws and regulations of governing agencies

The type of hazards present in the workplace
The number of workers in the workplace
The number of sections in a HCF
For a waste spill hazard, the basic first aid kit shall contain the following:
Adhesive bandages/tape (band-aids, sticking plasters)
Dressing (sterile, applied directly to wound)
Sterile eye pads
Sterile gauze pads
Bandages (for securing dressings, not necessarily sterile)
Butterfly closure strips
Saline Soap
Antiseptic
Practices to mitigate / prevent waste spill include the following:

Provision of safety reminders and signage on strategic areas
Education and training on proper sealing of waste plastic liners
Minimal handling of waste
Collection of waste shall be done when bin is three-fourths (3/4) full
Provision of plastic liner in accordance to standard specification (please see
Chapter 5)
Provision of leak proof container
Proper use of standard waste trolleys during transport
Opening of sealed bags shall be avoided
Availability of Spill Kit
Strict compliance to all policies and procedures
9.6.2 Emergency Response

Emergency response refers to the activity carried out by a group of well-trained
HCF worker after activation of the HCF response team. This includes implementation
of the emergency management plan such as the activation of the incident command
system relevant to exposure to hazardous substance, whether infectious, chemical and
biological spillage and toxic substance.
The area where the hazardous waste was accidentally contaminated must be cleaned
thoroughly by the team following standards of emergency response (e.g. isolation,
wearing PPE, incident command system, etc.). A designated triage with medical
and nursing staff shall handle individuals who are contaminated before transport to
the Emergency Room for further treatment. Figure 9.5 illustrates an example of an
emergency response to incident on chemical and biological spillage.
131
9.6.2.1 Needle Prick Injury

Needle stick safety shall always be a priority. The following steps in handling a
needle stick injury are highly recommended:
Step One Cleaning the Wound
Clean the wound with soap and water. Do not pinch or squeeze blood out of the
wound or apply bleach.
Step Two Testing
It is critical that the injured HCF worker is tested for HIV, hepatitis B and
hepatitis C as soon as possible.
Step Three Report the incident
In order to maintain needle stick safety, always report incidence of needle stick
injury through an incident report according to infection control protocol.
Step Four Retesting
Injured HCF worker shall be retested for hepatitis C six (6) weeks after the
needle stick injury and after four to six (4 6) months for hepatitis C virus
antibodies and elevated liver enzymes. After HIV exposure, the injured shall get
tested at the sixth (6th) week and again on the third (3rd), sixth (6th) and twelfth
(12th) month for antibodies to HIV. The frequency will vary depending on the
risk of transmission.
9.6.2.2 Prevention of Needle Stick Injuries

In order to prevent needle stick injuries, the principle of minimal handling is
recommended. The HCF worker shall never attempt to manually recap a used
syringe, as this method had the highest probability of injury. Needle/hub cutters are
recommended for use.
The HCF can develop a simple technology that will allow the HCF worker to
safely recap the syringe, thus allowing the needle to be separated from the barrel and
disposing the two in separate waste containers. An example of an invented Needle
Recapper, developed by San Juan de Dios Educational Foundation Inc. (Hospital), is
illustrated in Figure 9.4.
132
Figure 9.4 Needle Recapper Procedure

Courtesy of San Juan de Dios Educational Foundation Inc. (Hospital), Pasay City
133
9.6.2.3 Spill Control

Spillage usually requires clean-up only of the contaminated area. For spillage of
infectious material, however, it is important to determine the type of infectious agent.
The Infection Control Officer can be asked for assistance regarding proper management
and clean-up of the spill due to infectious waste. In some cases, evacuation of the area
may be necessary. Procedures for dealing with spillage shall specify safe handling
operation and appropriate protective clothing. In case of skin and eye contact with
hazardous substance, there shall be immediate decontamination. The exposed person
shall be removed from the area of the incident for decontamination, generally with
copious amounts of water. Special attention shall be paid to the eyes and any open
wounds. In case of eye contact with corrosive chemicals, the eyes shall be irrigated
continuously with clean water for 10 30 minutes; the entire face shall be washed in
a basin, with the eyes being continuously opened and closed. An eye wash assembly
can be installed in the unit for immediate response.
9.6.2.4 Immediate Actions

Secure the affected area
Check for any person involved
Person contaminated with waste spill shall de decontaminated for at least fifteen
(15) minutes (emergency shower) and taken for medical examination
If eyes are affected, do not rub eyes to avoid further irritation
Administer first aid
Isolate the spill (if safe to do so)
Contact the Safety Officer and
Pollution Control Officer for high
risk spills
Follow the spill clean-up procedure
Document the occurrence of the spill
through incident/accident report.
9.6.2.5 General Guidance for Spill Control

1. Vacate and secure the area to
prevent further exposure of other
individuals.
2. Provide first aid and medical care to
injured individuals.
3. Inform WMO who shall coordinate
the necessary actions.
4. Determine the nature of the spill.
Refer to the MSDS if necessary.
5. Provide appropriate clothing to personnel involved in cleaning-up.
6. Limit the spread of the spill.
134
7. Activate exhaust system or keep the area well-ventilated particularly if the spill
is due to volatile organic solvents or corrosive agents.
8. Neutralize or disinfect the spilled or contaminated material if indicated.
9. Collect all spilled and contaminated materials (sharps shall never be picked
up by hand; brushed and pans or other suitable tools shall be used). Spilled
materials and disposable contaminated items for cleaning shall be placed in
appropriate waste bags or containers and properly labelled and documented
before final disposal.
10. Decontaminate or disinfect the area, wiping with absorbent cloth. The cloth (or
other absorbent material) shall NOT be turned during this process, because this
will spread the contamination. Work from the least to the most contaminated part
of the spill while changing cloth at each stage to carry out the decontamination.
Dry cloth shall be used in the case of liquid spillage and spillage of solids, while
wet cloth shall be used for acidic, base or neutral chemicals.
11. Decontaminate or disinfect all tools used.
12. Seek medical attention if exposure to hazardous material has occurred during the
operation.
13. Normal operation may continue once the disinfected area is thoroughly cleaned
and dried.
The clean-up kit for spill shall contain the following items :
a. One (1) pair of latex gloves

b. One (1) N95 mask (for blood, body fluids and chemotherapeutics/cytotoxics
spills)
c. Respirator with specific filter for the type of chemicals
d. One (1) Zip lock bag small
e. One (1) Zip lock bag big
f. Absorbable cloth
g. Appropriate disinfectant solution for spills due to blood, body fluids and
chemotherapeutics/cytotoxics
h. Neutralizing solution specific for acids or alkali
i. Eye goggles (for big spill)
j. Labeling materials
k. Small pail with putty clay at the bottom (for chemical spill)
l. Miscellaneous items which the HCF may require to meet their need
A summary of emergency procedures to be done for specific type of waste spills are
listed in Table 9.1.
135
Table 9.1 Procedures for Emergency Response to Waste Spills
Type of Waste Immediate Response Follow-up Person In-

Spill Procedures charge
1.Biohazardous Waste Spill
1.1Minor spill 1.)Make sure that the biosafety cabinet 1.)Know the nature Infection
- occurs inside continues to operate of the organism Control Officer
biosafety 2.)If only a small quantity is spilled, involved
cabinet, no one decontaminate the surfaces within the cabinet, 2.)Report to the
is exposed wearing gloves and using 16% bleach solution person-in-charge
3.)If a large quantity is spilled, entire cabinet
including fans, filters, airflow plenums, will
need to be decontaminated (40% solution
required)
1.2Major 1.)Evacuate the room, breathing as little as 1.)Know the nature Infection
spill - occurs possible of any aerosols of the organism Control Officer
outside 2.)Close the door of the room involved
biosafety Remove any and all contaminated clothing 2.)Report to the
cabinet, people and place it in sealed plastic containers person-in-charge
are exposed 3.)Thoroughly wash hands and face with
disinfectant soap. Shower if necessary
2. Chemical Waste Spill
2.1Corrosives 1.)If corrosive gets contact with eyes, go 1.)Do not apply Safety Officer
(acids and immediately to eyewash station any neutralizers or
bases) 2.)Remove contact lenses, if any ointments to the
3.)Flush eyes for 15-20 minutes eyes
2.)Seek medical
attention
2.2Reactives 1.)Leave the area quickly 1.)Inform person in- Safety Officer
(explosives, 2.)Close the doors charge
oxidizers, 3.)Go directly to the eyewash station, shower, 2.)Seek medical
unstable or fresh air area attention
chemicals)
2.3Toxins and 1.)If inhaled, go to fresh air area right away 1.)Get medical help Safety Officer
Poisons 2.)If swallowed, seek medical help 2.)If swallowed, do
immediately. not induce vomiting
3.)If it got into your eyes, go to the nearest nor eat/drink
eyewash station. Remove contact lenses, if anything unless
any. Flush eyes for 15-20 minutes instructed to do so
4.)If on skin, dont rub the affected area. in the MSDS or by
Rinse with running water for 15-20 minutes medical personnel
5.)Remove all contaminated clothing
Note: The functions of the Safety Officer may include: a) conduct investigation on
accidents and incidents related to waste management including spills and leaks;
b) provides assistance to government agencies in the conduct of health and safety
inspection, accident/incident investigation or any other related problems; and c)
maintains or helps in the maintenance of an efficient accident/incident record system
and coordinates actions taken by the HCF.
Source: American Hospital Association, 1992
136
Figure 9.5 Emergency Response to Waste Spillage

137
9.6.3 Recovery Phase

The recovery phase can be characterized as a return to normal situation that is
similar to the situation that existed prior to the incident. Recovery phase activities can
include the following:
Preparation of incident/accident report

Inventory of used items
Provision of new supplies to replace the used items in the kit
Psychosocial debriefing of the injured person, as necessary
9.6.3.1 Reporting Accidents and Incidents

HCF workers shall report all accidents and incidents, e.g. spillage to the Health
and Safety Committee for appropriate action. They shall be educated on the possible
effects of hazardous materials once spilled to encourage prompt reporting. Accidents
or incidents, including near-misses, spillage, damaged containers, inappropriate
segregation and any incident involving sharps shall be reported to the HCWMC
(if waste is involved) or to another designated person. The report shall include the
following details:
1. The nature and magnitude of the accident or incident

2. The place, date and time of the accident or incident
3. The staff who is directly involved
4. Immediate response taken
5. Any other relevant circumstances
6. Recommendations, if any
The WMO or other responsible officer, who shall take possible action to prevent
recurrence, shall investigate the cause of the accident or incident. The records of
the investigation and recommendations must be submitted to the management for
review and approval. Any amendment in the policies and procedural guidelines must
be integrated in the HCWMP of the HCF. Updates shall be disseminated to all HCF
workers for information and guidance. All records of spill management must be kept
for future reference. An example of a reporting flow for a tertiary hospital is shown in
Figure 9.4.
Sample of the Occupational Incident/Accident Report Form is attached in Annex
E The Sample Flowchart on the Management of Occupational Accident/Incident for
Tertiary Hospitals is found in Annex F.
There shall be an established reporting system in all HCWM-related incidents. A
clear investigating system must be ensured and effective corrective action must be
employed.
138
9.6.3.2 Inventory of Used items

HCWMP of respective HCF shall identify person responsible for the inventory of
used items during the clean-up and ensure replenishment of the first aid and spill kits.
Usually the WMO, Head Nurse or Supervisor of the affected area is designated for this
function.
9.6.3.2 Provision of New Supplies

The Central Storage Facility of the HCF shall provide replacement of the used
items and ensure continuity of supplies. Actual cost incurred during clean-up shall be
documented accordingly.
9.6.3.3 Psychosocial Debriefing of Victims

Trained and qualified personnel shall conduct psychosocial debriefing on the
victim/s, as necessary. Debriefing shall be conducted immediately after the incident/
accident. If the HCF has no capability to conduct this activity, the victim may be
referred to other HCF providing such service. Record of management shall be kept
for future reference.
139
140
PART IV
GLOSSARY OF TERMS
ANNEXES
AND
REFERENCES
142
GLOSSARY OF TERMS
Definition of Terms as Used in the Manual

Antineoplastic : Inhibiting the development of neoplasms or abnormal
tissue growth
Autoclaving : Method of sterilization using an equipment for effective
sterilization by steam under pressure and temperature.
Collection : Act of safe transporting of HCW from source or from a
central storage area.
Cytotoxic : A substance possessing a specific destructive action on
certain cells; used in particular in referring to the lysis
(disintegration or dissolution) of cells brought about by
immune phenomena and to antineoplastic drugs that
selectively kill dividing cells.
Decontamination : Reduction of microbiological contamination to a safe
level.
Disinfection : Reduction or removal of disease-causing
microorganisms (pathogens) in order to minimize the
potential for disease transmission
Disposal : Discharge, deposit, placing or release of any healthcare
waste into or on any air, land, or water.
Half-life : Specific period that a radiation element decays.
Genotoxic : A substance that is capable of interacting directly with
genetic material, causing DNA damage that can be
assayed. The term may refer to carcinogenic, mutagenic,
or teratogenic substances.
Hazardous waste : All waste generated by HCF except general waste
Healthcare Workers shall refer to all staff in the HCF i.e., doctors, nurses,
administrative staff, paramedical, ancillary workers,
institution workers, nursing attendants, dental aides,
laboratory aides, janitors, maintenance, radiology aide,
social workers, etc.
Highly infectious waste : Cultures and stocks of highly infectious agents; waste
from autopsies, animal bodies, and other waste items that
have been inoculated, infected or in contact with such
agents. Wastes contaminated with organisms belonging
to Biosafety Levels 3 and 4. Wastes contaminated with
pathogens mentioned in DOH Administrative Order
2010-0033
Household Waste : Wastes produced from activities within the household.
Infectious Waste : Waste that contain pathogens like bacteria, viruses,
parasites or fungi in sufficient concentration or quantity
to cause disease in susceptible hosts.
143
Leachate : Liquid produced when healthcare waste undergoes

decomposition, and when water percolates through solid
waste undergoing decomposition. It is a contaminated
liquid that contains dissolved and suspended materials.
Non-hazardous waste : Waste that has not been in contact with infectious
agents, hazardous chemicals or radioactive substances,
and that does not pose a sharps hazard
Off-site collection : Collection and transfer of segregated HCW from the
HCF- Central Storage Area (CSA) to DENR Accredited
Off-site transport : Transporter/ Municipal Waste Collector/ Supplier
Transport of segregated HCW from HCF to Treatment
Facilities or to Final Disposal Area
On-site collection : Collection of segregated HCW from the point of
generation to designated color-coded bins
On-site transport : Transport of collected segregated HCW from the
designated color-coded bins to CSA
Pyrolysis : Thermal decomposition of substance and materials
in the absence of supplied molecular oxygen in the
destruction chamber in which the said material is
converted into gaseous, liquid, or solid form.
Radioactive Waste : Material that contains, or is contaminated with,
radionuclides at concentrations or activities greater than
clearance levels.
Recyclable : Any waste material retrieved from the waste stream
and free from contamination that can still be converted
into suitable and beneficial use or for other purposes,
including, but not limited to cardboard, glass, office
paper, drink cans, newspapers, magazines and
polyethylene or polyprophelene plastics (PE and PET).
Recycling : Processing of used materials (waste) into new products
to prevent waste of potentially useful materials, reduce
the consumption of fresh raw materials, reduce energy
usage, reduce air pollution and water pollution (from
land filling) by reducing the need for conventional
waste disposal, and lower greenhouse gas emissions as
compared to virgin production .
Re-use : Process of recovering materials intended for the same
or different purpose without the alteration of physical
and chemical characteristics.
Sanitary Landfill : An engineered method designed to keep the waste
isolated from the environment.
144
GLOSSARY OF TERMS
Segregation : Separating the waste generated by the healthcare

facility according to the specific treatment and disposal
requirements.
Sludge : Accumulated solids that separate from liquids such as
water or wastewater during processing, or deposits on
the bottom of streams or other bodies of water.
Sterilization : Destruction of all microbial life
Storage : Area or place where healthcare waste is temporarily
stored after generation and prior to collection for
ultimate recovery or disposal.
Waste Disposal : Refers to the intentional burial, deposit, discharge,
dumping, placing, or release of any waste material into
or on air, land, or water
Waste Generator : Any person, organization, or facility engaged in
activities that generate waste
Waste Management : All the activities, administrative and operational,
involved in the handling, treatment, storage, collection,
transportation, and disposal of wastes
Waste Treatment : Any method, technique, or process for altering the
biological, chemical, or physical characteristics of waste
to reduce the hazards it presents and facilitate or reduce
the costs of disposal. The basic treatment objectives
include volume reduction, disinfection, neutralization,
or other change of composition to reduce hazards
including removal of radionuclides from radioactive
wastes
145
A nnexA A
ANNEX
World Health Organization Technical Guidelines
1. World Health Organization: Safe Management of Wastes from Healthcare

Activities (1999)
The WHO Guidebook (more commonly known as the Blue Book) is the first global
and comprehensive document about healthcare waste management. It is aimed at national
and local administrators, HCF managers, policy makers, and public health professionals.
It discusses the different aspects of healthcare waste, such as its health impacts,
legislative and policy aspects, HCW Management Planning, waste minimization,
handling, storage and transportation of wastes, treatment and disposal strategies, waste
water management, health and safety of healthcare personnel, emergency response,
infection control and training.
A teachers guide accompanies the Bluebook for training purposes. This guide, entitled,
Management of Wastes from Healthcare Activities, is designed for a three-day training
course. It includes overhead slides, handouts, and exercises.
2. World Health Organization: Practical Guidelines for Infection Control in

Healthcare Facilities (2004)
This guidebook was created in response to the need for an efficient infection control
program in the advent of emerging diseases such as the Severe Acute Respiratory
Syndrome (SARS) and re-emerging diseases such as the bubonic plague and tuberculosis.
The guidebook was directed to healthcare facility workers who are tasked to protect
themselves and other people from disease transmission. This guidebook was also directed
towards healthcare facility administrators who need to implement a successful infection
control program in their institution.
3. World Health Organization: Laboratory Safety Manual, Third Edition (2004)
Classification of Microorganisms is based on the Risk Group it belongs to. The grouping
done is based on several characteristics of the microorganism, such as its pathogenicity,
mode of transmission, and host range. In turn, these characteristics may be influenced by
the existing levels of immunity, density and movement of the host population, presence
of appropriate vectors, and the standards of environmental hygiene in the area. The
following are the four levels of risk groups, wherein Group 1 has the lowest risk, and
Group 4 has the highest risk.
a. WHO Risk Group 1 (no or low individual and community risk). A microorganism
that is unlikely to cause human disease or animal disease
146
146
ANNEXES
ANNEXES
b. WHO Risk Group 2 (moderate individual risk, low community risk). A pathogen
that can cause human or animal disease but is unlikely to be a serious hazard to
laboratory workers, the community, livestock or the environment. Laboratory
exposures may cause serious infection, but effective treatment and preventative
measures are available and the risk of spread of infection is limited.
c. WHO Risk Group 3 (high individual risk, low community risk). A pathogen that
usually causes serious human or animal disease but does not ordinarily spread
from one infected individual to another. Effective treatment and preventive
measures are available.
d. WHO Risk Group 4 (high individual and community risk). A pathogen that
usually causes serious human or animal disease and that can be readily transmitted
from one individual to another, directly or indirectly. Effective treatment and
preventive measures are not usually available.
147
147
A nnex B
ANNEX B
CONSIGNMENT NOTE
(Sample Format)
A. TRANSPORTER
Name: ____________________________
Address: _____________________________
Telephone No.: _____________________ Accreditation No.:_________________
Type of Waste Transported: __________________________ Quantity (kg): _________
B. GENERATOR
Name: ____________________________
Address:________________________________
Telephone No.: ___________________________
C. TREATMENT FACILITY
Name of Manager/Authorized Representative: __________________________________
Address: _______________________________Telephone No.: ____________________
Permit to Operate: (Permit No.) _____________________________________________
Signature of Manager/Authorized Representative:
____________________________________
B. DATE WASTES ARE COLLECTED/TRANSPORTED/RECEIVED

Date Collected/Removed from Generators Facility:
___________________________________
Date Received by the Transfer Station (Point of Consolidation):
_________________________
Date Received by the Treatment Facility:
___________________________________________
148
148
ANNEXES
ANNEXES
A
ANNEX
nnexCC
SAMPLE SELF-MONITORING SHEET
Healthcare Waste Management Program
AREA OF THE HOSPITAL: _____________________________________________
DATE OF INSPECTION:________________MONITORING RATING: _________
SCORE INDICATORS
Reference Actual
A. WASTE MINIMIZATION 20%
PRACTICES
1. Re-uses/recycles used containers, 10 Percentage of recyclable wastes that were
articles, papers, etc. recycled multiplied to 0.10
2. Use of only environment friendly 10 No Styrofoam (polystyrene) and plastic
products and materials (PVC) = 5, otherwise, the score is 0; and
No mercury containing devices used = 5,
otherwise, the score is 0
B. WASTE SEGREGATION 25%
1. Waste properly segregated in 5 No mixed wastes seen at all times= 5,
correct plastic liners otherwise, the score is 0
Black/Clear: Non-Biodegradable
General Waste
Green: Biodegradable General
Waste
Yellow: Infectious Waste
2. Color-coded plastic liners with 4 Color coding and proper tagging and
proper tagging and labeling labeling strictly followed at all times= 4,
otherwise, the score is 0
3. Use puncture-resistant and leak- 4 Only puncture-resistant and leak-proof
proof sharps container for sharps sharps container used for sharps waste = 4,
otherwise the score is 0
4. Waste bins strategically placed in 4 Waste bins are placed in strategically
designated area designated areas = 4, otherwise, the score is
0
5. Proper segregation of recyclable 4 Proper segregation practiced at all times= 4,
items otherwise, the score is 0
6. Empty vials brought to the 4 Proper management of empty vials
pharmacy section by the nursing practiced at all times= 4, otherwise, the
attendant/personnel-in-charge for score is 0
proper recording and crushing
(logbook available)
C. WASTE ON-SITE 20%
COLLECTION, TRANSPORT
AND STORAGE
1. On-site collection scheduled 2 Strict adherence to on-site collection
strictly followed schedule = 2, otherwise, the score is 0
2. Janitorial Service uses standard 3 Standard trolley is used to collect waste on-
trolley with enclosure in collecting site= 3, otherwise, the score is 0
waste
3. Janitorial Service directly 3 Waste is directly transported to Central
transports waste collected to Storage Area= 3, otherwise, the score is 0
Central Storage Area
4. No presence of spillage during 3 No occurrence of spillage during collection
collection and transport and transport= 3, otherwise, the score is 0
149
149
5. Waste bins thoroughly cleaned/ 3 Waste bins thoroughly cleaned at all times=
washed by janitors 3, otherwise, the score is 0
6. Waste transportation route 3 Waste transportation route strictly followed
followed at all times= 3, otherwise, the score is 0
7. Final disposal of waste in 3 Final disposal of waste in accredited DENR
approved DENR facility facility= 3, otherwise, the score is 0
D. WASTE TREATMENT ON 10%
SITE (If applicable)
1. Treatment of highly infectious 4 Highly infectious waste treated at all times=
waste conducted 4, otherwise, the score is 0
2. In case of chemical disinfection, 3 Only the allowed chemicals are used for
used only allowed chemicals such chemical disinfection= 3, otherwise, the
as Sodium Hypochlorite, Chlorine score is 0
Dioxide and Hydrogen Peroxide
3. In case of the use of microwave or 3 Equipment has passed the validation test=
autoclave, the equipment has 3, otherwise, the score is 0
passed the validation test
E. WASTE WATER 15%
MANAGEMENT (Personnel in-
charge)
1. Regular testing of effluents 5 Effluents tested regularly= 5, otherwise, the
score is 0
2. Preventive maintenance schedule 10 Strict adherence to STP maintenance
for Sewage Treatment Plant (STP) schedule= 10, otherwise, the score is 0
followed
F. ADMINISTRATIVE 10%
1. Staff with formal training and 2 Staff had undergone formal training and
education on proper healthcare education on proper HCWM= 2, otherwise,
waste management (HCWM) the score is 0
2. Infection control protocol 4 Strict adherence to infection control
observed and practiced protocols at all times= 4, otherwise, the
score is 0
3. Posters and other IEC materials 2 On-site presence and visibility of posters
available on-site and other IEC materials= 2, otherwise, the
score is 0
4. Accident/incident reports 2 Prompt submission of complete accident/
submitted if any incident reports, if any= 2, otherwise, the
score is 0
TOTAL PERCENTAGE 100%
MONITORING TEAM: ______________________ _________________________
Signature of Area Supervisor: _______________________________
Monitoring Rating
Grade/ Actual Score/ Interpretation
5 100% Excellent, with full compliance

4 91 -99% Highly Satisfactory,
with highly adequate compliance
3 81-90% Satisfactory, with adequate compliance
2 75-80% Fair, with compliance
1 74% and below Poor, low compliance
150
150
SAMPLE MONITORING TOOL FOR THE WASTE COLLECTOR
AREA OF THE HOSPITAL:
ANNEX D
MONTH OF COLLECTION: AREA SUPERVISOR: _____________________________________________________________
LEGEND: I Infectious Waste PH (A) Pharmacological Waste(Expired/Used Drugs) Hg Mercury and Other Heavy Metals G (C) Non-biodegradable/ Non-Recyclable Waste
S Sharps PH (B) Pharmacological Waste (Cytotoxic/Genotoxic/Antineoplastic) R Radioactive Waste G (D) Aerosol and Pressurized Containers
P Pathological Waste PH (C) Pharmacological Waste (Empty Vials/Ampoules) G (A) Biodegradable/ Food Waste
A Anatomical Waste C Chemical Waste G (B) Non-biodegradable/ Recyclable Waste
Annex D
DATE TIME VOLUME OF WASTE NOTES

I S P A PH PH PH C Hg R G G G G (Check if YES, if NOT, provide explanation.
(A) (B) (C) (A) (B) (C) (D) Place a slash / after your explanation to separate it from that of the next shift)
Shift 1 2 3
1 _ _ _ Proper segregation practiced? If not Improper practice/s: ____________________________
__________________________________________________________________________
_ _ _ Supply of liners adequate?
# of liners left: (__/__/__)Yellow (__/__/__)Green (__/__/__)Black
If not, # liners needed: (__/__/__/)Yellow (__/__/__)Green (__/__/__) Black
Shift _ _ _ Bins cleaned after collection? If not,
2 ________________________________________________
_ _ _ Trolley cleaned after collection? If not,
______________________________________________
_ _ _ Disinfectant used? Type of Disinfectant: ____/____/____/Conc. of Disinfectant: ___/___/___/
_ _ _ Bins in good condition? If not, repairs needed: ______________________________________
_ _ _ PPEs used? If not, _________________________________________________________
Shift
_ _ _ PPES in good condition? If not, repairs/ new equipment needed: _______________________
3
Name and Signature of Collector:
________________________ ________________________ __________________________
Shift 1 Shift 2 Shift 3
Shift 1 2 3
1 _ _ _ Proper segregation practiced? If not Improper practice/s: ____________________________
__________________________________________________________________________
_ _ _ Supply of liners adequate?
# of liners left: (__/__/__)Yellow (__/__/__)Green (__/__/__)Black
If not, # liners needed: (__/__/__/)Yellow (__/__/__)Green (__/__/__) Black
Shift _ _ _ Bins cleaned after collection? If not,
2 ________________________________________________
_ _ _ Trolley cleaned after collection? If not,
______________________________________________
_ _ _ Disinfectant used? Type of Disinfectant: ____/____/____/Conc. of Disinfectant: ___/___/___/
_ _ _ Bins in good condition? If not, repairs needed: ______________________________________
Shift _ _ _ PPEs used? If not, _________________________________________________________
3 _ _ _ PPES in good condition? If not, repairs/ new equipment needed: _______________________
Name and Signature of Collector:

________________________ ________________________ __________________________
Shift 1 Shift 2 Shift 3
TOTAL SUMMARY OF NOTES:
151
ANNEXES
ANNEXES
MANUAL ONHEALTHCARE
MANUAL ON HEALTHCARE WASTE
WASTE MANAGEMENT,
MANAGEMENT, THIRD EDITION
THIRD EDITION
ANNEX
A nnexE E
Name of Hospital
Infection Control Committee
SAMPLE OCCUPATIONAL INCIDENT/ACCIDENT REPORT (OIR) FORM
Part 1
1. Name:____________________ Date of Incident/Accident: __/__/__ Time: _____ (A.M./P.M.)

2. Describe the incident fully:
a. Actual task during the incident: _____________________________________________
b. Area of assignment during the incident: _______________________________________
c. Type of Exposure: (tick only the box that apply)
Sharp Needle Surgical Glass Other sharp item, specify

Injury Instrument _____________
Blood/body Splash Spillage
fluids
exposure
Vomitus Sputum Saliva Blood/blood products
CSF Pleural Fluid Urine Feces
Others,
specify
Chemicals Splash Spillage Specify ______________________
Others, ______________________________________________________________________
Specify
d. Location of Exposure/Injury o the body part (tick only the box that apply)
Intact Skin Wound Eyes Nose Mouth Others, specify
__________
e. Personal Protective Equipment worn at the time of exposure(tick all the boxes that apply)
Gloves, single Goggles Surgical Mask N95 Lab.
pair respirator Coat/gown
Gloves, double Face Shield Disposable Other sharp item,
pair Gown specify___________
f. Immunization Status: Hep B Tetanus Unknown Others,
specify:_______________________
3. Risk Assessment (tick only one):
High Risk Exposure (source of exposure from HIV* ans HBV/air-borne diseases)
Low Risk Exposure (source of exposure from HIV* ans HBV/air-borne diseases)
4. A. Corrective action undertaken: ________________________________________________

B. Plans to prevent similar incidents from occurring in the future:
_____________________________________________________________________________
_____________________________________________________________________________
________________________________
5. Referred to Emergency Medical Service / Emergency Room Physician?
Yes Date: __/__/__ No Why?_____________________________________
152
152
ANNEXES
ANNEXES
Accomplished By:
Name and Signature: _________________________________ Date: __/__/__

Department / Section: ______________________________________________
======================================================================
Part II (To be filled-up by ICN)
1. Name of Attending Physician: __________________________________________________

2. Advice/Treatment Given: ______________________________________________________
___________________________________________________________________________
___________________________________________________________________________
3. Additional recommendation/suggestions:_________________________________________
___________________________________________________________________________
___________________________________________________________________________
ALL MEDICAL DATA IS CONFIDENTIAL
Note: For HIV exposure, refer to HACT for further evaluation and management.
153
153
A nnexF F
ANNEX
SAMPLE FLOWCHART ON THE MANAGEMENT OF OCCUPATIONAL
ACCIDENT/INCIDENT FOR TERTIARY HOSPITALS
OCCUPATIONAL INCIDENT/ACCIDENT
Hospital employee Student Affiliates
DO Immediate First Aid Care*

For major accidents, CALL FOR HELP
Nurses/Med. Tech Medical Intern
NOTIFY IC Link Staff NOTIFY Point NOTIFY MTO In-Charge (during

(Nurse Supervisor/Doctor/Head of Person (CI/NTO In- office hour) & MOIII in areas of
Charge Med. Tech. Staff) assignment (after office hour)
Section)
Link-staff/Point Person LOGS incident and FILLS-UP Occupational Incident (OIR) Form
ADVICE concerned employee to bring properly filled- ENDORSE student affiliate to ER together with
up OIR form to EMS (during office hours) for properly filled-up OIR form for appropriate
appropriate management management
ICN COLLECTS OIR form from Emergency Medical Service/ER IC Link-Staff
Infection Control Committee

1. KEEP original OIR at ICC for safe-keeping and FOLLOW-UP of cases
2. GIVE duplicate copy of OIR to EMS IC link-staff/student affiliates point
person for safe-keeping
3. PROVIDE copy of OIR on waste associated incident to Chair, Waste
Management Committee
Legend:
*IMMEDIATE FIRST AID CARE MEANING OF ACRONYMS

For wounds/needle sticks MTO -Medical Training Officer
- Allow the wound to bleed freely or squeeze lightly to facilitate NTO -Nursing Training Officer
bleeding CI -Clinical Instructor
- Wash wounds/cuts with soap and water thoroughly then apply MO -Medical Officer
povidone iodine
For mucous membrane splash: IC -Infection Control
- Flush splashes of the nose, mouth or the exposed area
ICN -Infection Control Officer
immediately with water for 10-15 minutes OIR -Occupational Incident
- Irrigate eyes with clean water, sterile eyewash or saline Report
irrigating solution
For skin contamination
- Stop the procedure as soon as exposure has occurred
- Wash the exposed area thoroughly with soap and running
water
154
- If desired, use alcohol as an antiseptic after thorough
handwashing
154
ANNEXES
ANNEXES
Annex G
Annex G
Advantages and Disadvantages of the Different Types of WTP
WTP
Advantages Disadvantages
Technology
1.Anaerobic Suitable for smaller and Experts are required for the
Baffled Reactor larger settlements design and supervision
(ABR) Little space required due to Master mason is required
underground construction for water-tight plastering
Low investment costs Effluent is not completely
Very low operation and odorless
maintenance costs. No Slow growth rate of
moving parts power anaerobic bacteria means
needed. Hardly any long start-up period
blockage Less efficient with weak
Simple and durable wastewater
High treatment efficiency
2. Waste Simple to build, reliable Large area requirement
Stabilization and easy to maintain Poor quality of treated
Ponds Provides pathogen removal effluent
which is better than the May promote breeding of
conventional treatment insects in the pond
Used in small communities Needs to be located far
Low in construction and from communities
operating cost
3. Engineered Easy and simple to Requires larger land area
Reed Bed maintain and operate Low treatment efficiency
Low-cost secondary Professional/specialist
treatment option needed in design and
Pleasant landscaping is construction
possible
155
155
WTP Technology Advantages Disadvantages

4. Sequencing Efficient Treatment Most of the component
Batch Reactor Tolerates hydraulic and parts are patented and
(SBR) organic shock loads (high comes from abroad
inlet variation) Capacities are fixed and no
Modular construction flexibility
facilitates future expansion More expensive than other
Provides a simple, reliable, treatment methods
automatic, wastewater In case of power failure,
treatment process with a reactor may overflow
basin (simple design and Requires more skilled
construction) attention
Fully automatic (simple
and easy control and
operation)
Relatively small space
requirement
5. Rotating Low space requirement Contact media are not
Biological Can withstand hydraulic readily available in the
Contractors and organic surges more market
(RBC) effectively High capital cost of
High treatment efficiency equipment
Low energy and Must be covered for
maintenance requirement protection against rain,
Well drainable excess wing, sunlight and
sludge vandalism
Failures in shaft and media
Odor problems
6.Sludge Drying Simple to operate Filtrate/seepage water has
Bed Lowest cost option among to be treated
sludge dewatering methods Requires solar power
Energy-saving May produce odor and flies
nuisance
Source: Philippine Sanitation Sourcebook and Decision Aid, 2005
156
156
ANNEXES
ANNEXES
A nnexH H
ANNEX
August 24, 2005
JOINT DENR-DOH
ADMINISTRATIVE ORDER
No. 02, series of 2005
SUBJECT: Policies and Guidelines on effective and proper handling,

collection, transport, treatment, storage and disposal of health
care wastes.
I. RATIONALE
The Department of Environment and Natural Resources (DENR) and the Department of
Health (DOH) hereby jointly provide the following guidelines on the management of health care
wastes pursuant to, among others, the following laws, rules and regulations:
Clean Air Act of 1999 (Republic Act 8749);
Toxic Substances, Hazardous Waste, and Nuclear Waste Control Act of 1990
(Republic Act 6969);
Ecological Solid Waste Management Act of 2000 (Republic Act 9003)
Refuse Disposal of the Sanitation Code of the Philippines [Chapter XVIII,
Implementing Rules and Regulations, Presidential Decree 856];
Clean Water Act of 2004 [Republic Act 9275];
Environmental Impact Statement (EIS) System (Presidential Decree1586);
Hospital Licensure Act [Republic Act 4226]
II. OBJECTIVES
A. To provide guidelines to generators, transporters and owners or operators of
treatment, storage, disposal (TSD) facilities of health care waste on the proper
handling, collection, transport, treatment, storage and disposal thereof;
B. To clarify the jurisdiction, authority and responsibilities of the DENR and DOH
with regard to health care waste management; and
C. To harmonize efforts of the DENR and DOH on proper health care waste
management.
III. SCOPE AND COVERAGE
These policies and guidelines shall apply to health care waste generators, transporters and
owners or operators of TSD and final disposal facilities.
IV. DEFINITION OF TERMS
A. Health Care Wastes include all wastes generated as a result of the following:
1. Diagnosis, treatment, management and immunization of humans or animals;
2. Research pertaining to the above activities;
3. Producing or testing of biological products; and
157
157
4. Waste originating from minor or scattered sources (i.e. dental clinics, alternative
medicine clinics, etc.)
The categories of health care wastes ate enumerated in Annex A.
B. Health Care Waste Generators - include health care facilities, institutions, business
establishments and other small health care services with activities or work processes
that generate health care waste.
1. Hospitals (Primary Care, Secondary Care and Tertiary Care)

2. Infirmaries
3. Birthing Homes
4. Clinics
[a] Medical [e] Surgical
[b] Ambulatory [f] Alternative medicine
[c] Dialysis [g] Dental
[d] Health care centers and [h] Veterinary
dispensaries
5. Laboratories and Research Centers

[a] Medical and biomedical [e] Nuclear medicine laboratories
laboratories
[b] Medical research centers [f] Biotechnology laboratories
[c] Blood bands and blood collection [g] Animal research and testing
services
[d] Dental prosthetic laboratories [h] Drug testing laboratories
[i] HIV testing laboratories
6. Drug Manufacturers
7. Institutions
[a] Drug rehabilitation center [d] Schools of Radiologic Technology
[b] Training centers for embalmers [e] Medical Schools
[c] Med-tech intern training centers [f] Nursing Homes
[g] Dental Schools
8. Mortuary and Autopsy Centers
C. Health Care Waste Transporter a person licensed by the DENR Environmental
Management Bureau to convey healthcare waste through air, water or land.
D. Treatment, Storage and Disposal (TSD) Facilities facilities where hazardous
wastes are stored, treated, recycled, reprocessed and/or disposed of, as prescribed
under DENR AO No. 2004-36, Chapter 6-2 (Categories of TSD Facilities).
V. RESPONSIBILITIES OF IMPLEMENTING & COOPERATING AGENCIES

This Joint Administrative Order shall be implemented by the DENR through the
Environmental Management Bureau (EMB) and its Regional Offices, the National Solid Waste
Management Commission (NSWMC), and by the DOH through its Centers for Health
158
158
ANNEXES
ANNEXES
Development (CHD), Bureau of Health Facilities and Services (BHFS), Bureau of Health Devices
and Technology (BHDT), Environmental and Occupational Health Office (EOHO) of the National
Center for Disease Prevention and Control (NCDPC), the National Center for Health Facility
Development (NCHFD), and the National Reference Laboratory (NRL)-East Avenue Medical
Center, Quezon City.
A. The DENR-EMB shall:
1. Be the primary government agency responsible for implementing pertinent rules and
regulation on the management of health care waste in the Philippines, particularly
concerning the issuance of necessary permits and clearances for the Transport,
Treatment, Storage, and Disposal of such wastes, as governed by RA 6969, RA 8749,
RA 9275, RA 9003 and PD1586;
2. Formulate policies, standards and guidelines on the transport, treatment, storage and
disposal of health care wastes.
3. Oversee compliance by generators, transporters, TSD facility operators, and/or final
disposal facility operators with the proper transport, treatment, storage , and disposal of
health care wastes;
4. Conduct regular sampling and monitoring of wastewater in health care and TSD
facilities to determine compliance with the provision of RA 9275;
5. Require TSD facility operators and on-site treaters to present to the DENR copies of
the results of microbiological tests on the health care waste treated using autoclave,
microwave, hydroclave and other disinfection facilities prior to renewal of Permits
under RA 6969;
6. Provide technical assistance and support to the advocacy programs on health care
waste management; and
7. Notify the DOH on cases on non-compliance or notice of violation issued to health
care facilities, institutions and establishments licensed by the DOH.
B. The DOH shall:
1. Regulate all hospitals and other health facilities through licensure and accreditation
under the Hospital Licensure Act (Republic Act No. 4226);
2. Formulate policies, standards, guidelines systems and procedures on the management
of health care waste;
3. Develop training programs and corresponding modules on health care waste
management;
4. Provide technical assistance in the preparation of health care waste management plan
as a requirement for licensing or renewal thereof;
5. Provide technical assistance to ensure an effective and efficient implementation of
health care waste management program;
6. Require all health care waste TSD facility operators and health care waste generators
with on-site waste treatment facilities to use DOH-BHDT registered equipment or
devices used for the treatment of health care wastes;
7. Conduct regular performance evaluation of equipment/devices used for the treatment
of health care wastes by the DOH-BHDT;
159
159
8. Monitor the microbiological test of treated wastes to ensure compliance with DOH
standards;
9. Evaluate DOH hospitals compliance with proper health care waste management
program;
10. Issue Department Circulars to ensure that all environmental requirements are complied
with; and
11. Notify DENR on actions taken on cases of non-compliance or notice of violation
issued to health care facilities, institutions, and business establishments.
C. The DOH-Centers for Health Development shall:
1. Advocate health care waste management [HCWM] practices to the Local Chief
Executives, key leaders and other stakeholders;
2. Monitor health care waste management practices in all hospitals and other health care
facilities;
3. Provide technical assistance on health care waste management [HCWM] through:
a. Training
b. Advisory on the preparation of HCWM plans as a requirement for licensing or
renewal thereof
c. Dissemination of policies, guidelines and information
d. Monitoring and validation of implementation of HCWM
e. Develop, reproduce, and disseminate HCWM IEC material. Participate in any
public hearings related to HCWM.
f. Ensure compliance by health care waste generators with all pertinent laws, rules
and regulations on HCWM.
VI. GUIDELINES AND PROCEDURES

A. ENVIRONMENTAL COMPLIANCE REQUIREMENTS
A.1 Documentary Requirements
A.1.1 Health Care Waste Generators
Health care waste generators are required, based on existing laws, rules and
regulations, to register and secure the following permits:
A.1.1.1 From the DENR-Environmental Management Bureau
1. Environmental Compliance Certificate (ECC) for the establishment
of hospitals, health care facilities covered by the provisions of PD 1586
from the EMB Central Office or its Regional Offices.
2. Permit to Operate (P/O) for Air Pollution Source and Control
Installation from the EMB Regional Office.
3. Discharge Permit will be issued by the EMB Regional Office and the
Laguna Lake Development Authority (LLDA) based on RS 9275 or the
Clean Water Act of 2004 (See Annex B LLDA Jurisdiction)
4. Hazardous Waste Generators Registration in compliance with the
implementing rules and regulations of RA 6969 (DAO 29 series of 1992
and DAO 36 series of 2004) from the EMB Regional Office.
160
160
ANNEXES
ANNEXES
A.1.1.2 From the DOH-Bureau of Health Facilities and Services:

1. Licenses for hospitals, laboratories, dialysis clinics, birthing homes,
infirmaries, psychiatric hospitals, dental prosthetic laboratories, blood
banks, ambulatory clinics, and drug treatment and rehabilitation centers.
2. Certificate of Accreditation for Overseas Filipino Workers (OFW)
medical clinics, surgical clinics, drug testing laboratories, HIV testing
laboratories, water testing laboratories, medical technologist interm
training centers and training centers for embalmers.
A.1.2 Health Care Waste Transporters
Health care waste transporters are required, based on existing laws rules and
regulations, to undertake the following:
1. Register with EMB Central Office as healthcare waste transporter;
2. Secure Transport Permit from the DENR-EMB Regional Office;
3. Comply with the DENR Manifest System; and
4. Comply with other requirements specified in the Implementing Rules and
Regulations of RA 6969.
A.1.3 TSD Facilities
Owners or Operators of TSD facilities are required based on existing rules and
regulations to secure the following permits and clearances from DENR-EMB and DOH;
1. Environmental Compliance Certificate (ECC) for the Sanitary Landfill
(SLF) and TSD Facility from the EMB Central Office or Regional Office
2. Notice to Proceed for controlled dump facility to be used as repository of
health care waste from the EMB Regional Office
3. Registration as TSD facility based on the Implementing Rules and regulations
of RA 6969 from EMB Central Office
4. Technology Approval for non-burning technologies from the EMB Central
Office prior to the issuance of Permit to Operate
5. Permit to Operate (P/O) Air Pollution Source and Control Installation from
EMB Regional Office
6. Discharge Permit from the EMB Regional Office or LLDA
7. Certificate of Product Registration for equipment or devices used for treating
health care wastes from the DOH-BHDT
8. Certificate of Technical Evaluation for equipment or devices used for treating
health care wastes from NRL-EAMC
B. PROCEDURES FOR SECURING PERMITS AND LICENSES
Permits and licenses shall be secured following the established procedures of the DENR
and DOH.
161
161
C. SPECIFIC CRITERIA, STANDARDS, AND GUIDELINES

C.1 Handling, Collection, Standard and Transport
Handling, collection, storage and transport of health care wastes shall be in
accordance with the provisions of RA 8749, RA 6969, and RA 9003, and the DOH
Health Care Waste Management Manual (Chapter 5).
C.2 Treatment
1. Facilities shall consider technologies and processes used in health care waste
treatment such as (1) thermal, (2) chemical, (3) irradiation, (4) biological
processes, (5) encapsulation, and (6) inertization, as outlined in the DOH Health
Care Waste Management Manual and subject to compliance with the provisions
of RA 8749, RA 6969, and RA 9003.
2. Autoclave, microwave and hydroclave facilities shall use microbiological test to
determine the treatment efficiency of the units. The results of the
microbiological test shall be recorded and reported to DENR under RA 6969 and
RA 9003.
3. Health care waste generators and TSD facilities shall observe a level of
microbial inactivation of 6log10 reduction or greater than the most resistant
microorganism of concern in a given process.
4. Treated wastes and inert residues from TSD facilities must be disposed in
controlled disposal or sanitary landfill facilities duly licensed by the DENR to
handle the same.
5. Inertization is a suitable treatment for pharmaceutical wastes while
encapsulation and other immobilization techniques are treatment methods
considered for sharps, chemicals and pharmaceutical wastes and should therefore
be placed in final disposal facilities indicated under the subsequent Section.
C.3 Final Waste Disposal Systems and Facilities
The use of the proceeding disposal facilities should only be limited to health care
wastes which have undergone the necessary treatment provided under the prescribed
standards stipulated in the DOH Health Care Waste Management Manual.
C.3.1 Controlled Dump Facility
1. A Controlled Dump Facility (CDF) is and interim1 disposal facility for
municipal solid waste or those that are considered as non-hazardous and non-
toxic substances. In the absence of a sanitary landfill, a controlled dumpsite
could accept health care waste after the indicative treatment thereof.
2. In addition to the operational guidelines stipulated under Section 2 of Rule XIII
of the Implementing Rules and Regulations of RA 9003 or as indicated in the
conditions stipulated in the issuance of the NTP, a CDF that is commissioned to
1
As stipulated in Section 37 of RA 9003, no open dumps shall be established and operated, nor any practice or
disposal of solid waste by any person, including LGUs, which constitutes the use of open dumps for solid waste,
be allowed after the effectivity of this Act(February 16, 2001): Provided, that within three (3) years after the
effectivity of this Act (February 16, 2004), every LGU shall convert its open dumps into controlled dumps, in
accordance with the guidelines set in Section 41 of the Act: Provided, further, that no controlled dumps shall be
allowed five (5) years following effectivity of the Act (February 16, 2006).
162
162
ANNEXES
ANNEXES
accept treated health care waste should also be operated in accordance with the
following specific requirements:
a. Identify a particular cell within the facility to serve as a site for the
disposal of treated health care waste. The capacity of the allotted
cell/cell(s) should be measured in order to determine the actual volume of
wastes that can be accommodated in the facility.
b. Adequate signage should be placed in the health care waste deposition
area.
c. The cell should be lined with a material of low permeability, such as clay
or a geo-membrane such as a high-density polyethylene (HDPE) plastic
liner to contain the leachate and prevent contamination of groundwater
sources within the area.
d. Ensure that adequate soil cover is placed on the cells right after each waste
spreading.
e. Basic record keeping of the incoming waste indicating the time of receipt,
volume or weight, source identification (i.e. name of generator or source),
certification of treatment (or any similar form indicating that the waste
have undergone the necessary treatment) and the general condition of the
waste to be disposed.
C.3.2 Sanitary Landfill Facility
1. A Sanitary Landfill Facility (SLF) is a disposal site designed, constructed,
operated and maintained in a manner that exerts engineering control over
significant potential environmental impacts arising from the development and
operation thereof.
2. The required dedicated cells for treated health care wastes should be built or
developed prior to its operation to prevent the mixing thereof with municipal
solid wastes and other wastes.
3. Aside from the ECC, which is required for such facility, the construction and
development of an SLF must conform to RA 9003 and its Implementing Rules
and Regulations, particularly Sections 1 and 2, Rule XIV.
4. Existing sanitary landfill with approved ECC for the disposal of municipal solid
waste must secure and amendment of their ECC before accepting health care
waste for disposal thereat.
C.3.3 Safe Burial on Healthcare Facility Premises
1. Safe burial within the premises of healthcare facilities shall be allowed in remote
locations and rural areas where no TSD facilities are available. In such activity
of safe burial, the health care facility must ensure that the load or capacity of the
on-site burial pit is not exceeded.
2. Chemical treatment or disinfection is required prior to safe burial on hospital
premises.
3. The standards for safe burial within the healthcare facility premises shall follow
the guidelines specified in the DOH health Care Waste Management Manual
(See Annex C).
163
163
4. Relative to the guidelines provided by DOH, the operation of safe burial should
be in accordance with the minimum requirements for landfill.
C.3.4 Sharps and Syringes Disposal Through Concrete Vault
1. Disposal using concrete vault shall be allowed only as an alternative means of
disposal of used sharps and syringes.
2. Concrete vault shall be marked with proper signage: CAUTION: HAZARDOUS
WASTE OR SHARPS DISPOSAL AREA UNAUTHORIZED PERSONS
KEEP OUT.
3. Concrete vault should be watertight and must be constructed at least 1.5 meters
above the groundwater level.
4. The procedures for the safe burial of sharps and syringes through concrete vault
shall follow the guidelines in the DOH Health Care Waste Management Manual
(See Annex D).
C.4 WASTEWATER TREATMENT FACILITY
Healthcare facilities shall have their own Wastewater Treatment Facilities (WTF) or
maybe connected into a sewage treatment plant. However, facilities with laboratories
shall be required to pre-treat their wastewater prior to discharge into a sewage treatment
plant.
VII. REPEALING CLAUSE
All other issuances whose provisions of DENR and DOH Administrative Order,
Memorandum Circulars or other issuances inconsistent herewith are hereby repealed or modified
accordingly.
VIII. PENALTY CLAUSE
Failure to comply with the policies/guidelines shall be subject to the penalty provision(s) of
the applicable laws stated herein.
IX. EFFECTIVITY
This Order shall take effect immediately.
Published: Manila Standard Today

September 1, 2005
164
164
ANNEXES
ANNEXES
ANNEX A Categories of Health Care Waste
1. General Waste Comparable to domestic waste, this type of waste does not pose special
handling problem or hazard to human health or to the environment. It comes mostly from the
administrative and housekeeping functions of health care establishments and may also include
waste generated during maintenance of health care premises. General waste should be dealt
with by the municipal waste disposal system.
2. Infectious Waste this type of waste is suspected to contain pathogens (bacteria, viruses,
parasites, or fungi) in sufficient concentration or quantity to cause disease in susceptible hosts.
This includes:
2.1 Cultures and stock of infectious agents from laboratory work;
2.2 Waste from surgery and autopsies on patient with infectious diseases (e.g. tissues,
materials and equipment that have been in contact with blood or other body fluids);
2.3 Waste from infected patients in isolation wards (e.g. excreta, dressings from infected or
surgical wounds, clothes heavily soiled with human blood or other bodily fluids);
2.4 Waste that has been in contact with infected patients undergoing hemodialysis (e.g.
dialysis equipment such as tubing and filter, disposable towels, gowns, aprons, gloves
and laboratory coats);
2.5 Infected animal from laboratories; and
2.6 Any other instrument or materials that have been in contact with infected persons or
animals.
3. Pathological Waste Pathological waste consists of tissues, organs, body parts, human fetus
and animal carcasses, blood and body fluids. Within this category, recognizable human and
animal body parts are also called anatomical waste. This category should be considered as a
subcategory of infectious waste, even though it may also include healthy body parts.
4. Sharps Include needles, syringes, scalpels, saws, blades, broken glass, infusion sets, knives,
nails and any other items that can cause a cut or puncture wounds. Whether or not they are
infected, such items are usually considered as highly hazardous health care waste.
5. Pharmaceutical waste Includes expired, unused, split, and contaminated pharmaceutical
products, drugs, vaccines, and sera that are no longer required and need to be disposed of
appropriately. This category also includes discarded items used in handling of
pharmaceuticals such as bottles or boxes with residues, gloves, masks, connecting tubing and
drug vials.
6. Genotoxic Waste Genotoxic waste may include certain cytostatic drugs, vomit, urine, or
feces from patients treated with cytostatic drugs, chemicals, and radioactive materials. This
type of waste is high hazardous and may have mutagenic, teragenic, or carcinogenic
properties.
6.1 Harmful cytostatic drugs can be categorized as follows:
6.1.1 Alkylating agents cause alkylation of DNA nucleotides, which leads to cross-
linking and miscoding of the genetic stock;
6.1.2 Anti-metabolites: inhibit the biosynthesis of nucleic acids in the cell; mitotic
inhibitors: prevent cell replication
165
165
6.2 Cytotoxic wastes are generated from several sources and include the following:
6.2.1 Contaminated materials from drug preparation and administration, such as,
syringes, needles, gauges, vials, packaging; outdated drugs, excess (left over)
solutions, and drug returned from the wards;
6.2.2 Urine, feces, and vomit from patients which may contain potentially hazardous
amounts of administered cytotoxic drugs or of their metabolites and which should
be considered genotoxic for at least 48 hours and sometimes up to 1 week after
drug administration.
7. Chemical Waste Chemical waste consists of discarded solid, liquid, and gaseous chemicals,
for example from diagnostic and experimental works and from cleaning, housekeeping, and
disinfecting procedures. Chemical waste from health care may be hazardous or non-
hazardous.
7.1 Chemical waste is considered hazardous if it has at least one of the following properties:
7.1.1 Toxic
7.1.2 Corrosive (e.g. acids of pH <2 and bases of pH>12)
7.1.3 Flammable
7.1.4 Reactive (explosive, water-reactive, shock-sensitive)
7.1.5 Genotoxic (e.g. cytostatic drugs)
7.2 Non-hazardous chemical waste consists of chemicals with none of the above properties,
such as sugars, amino acids, and certain organic and inorganic salts.
8. Waste with high content of heavy metals Wastes with a high heavy-metal content
represent a subcategory of hazardous chemical waste, and are usually highly toxic. Mercury
wastes are typically generated by spillage from broken clinical equipment (thermometers,
blood pressure gauges, etc.). Whenever possible, spilled drops of mercury should be
recovered. Residues from dentistry have high mercury content. Cadmium waste comes
mainly from discarded batteries. Certain reinforced wood panels containing lead is still
being used in radiation proofing of X-ray and diagnostic departments. A number of drugs
contain arsenic but these are treated here as pharmaceutical waste.
9. Pressurized Containers Many types of gas are used in health care and are often stored in
pressurized cylinders, cartridges, and aerosol cans. Many of these, once empty or of no
further use (although they may still contain residues), are reusable, but certain types notably
aerosol cans, must be disposed of. Whether inert or potentially harmful; gases in pressurized
containers should always be handled with care; containers may explode if incinerated or
accidentally punctured.
10. Radioactive Waste Includes disused sealed radiation sources, liquid and gaseous materials
contaminated with radioactivity, excreta of patients who underwent radio-nuclide diagnostic
and therapeutic applications, paper cups, straws, needles and syringes, test tubes, and tap water
washings of such paraphernalia. It is produced as a result of procedures such as in vitro
analysis of body tissues and fluid, in vivo organ imaging, tumor location and treatment, and
various clinical studies involving the use of radioisotopes. Radioactive health care wastes
generally contain radionucleides with short half-lives, which ose their activity in a shorter
time. However, certain radionucleides e.g. C-14 contaminated wastes have muchlonger half-
life, more than a thousand years, which need to be specially managed in a centralized
treatment facility for radioactive wastes. The same is required for the management of disused
sealed radiation sources used for cancer treatment.
166
166
ANNEXES
ANNEXES
ANNEX B Laguna Lake Development Authority Jurisdiction
The Laguna Lake jurisdiction is limited to the water shed of the Laguna Lake which
consist of the following: Rizal Provinces (13 towns); Laguna Provinces (27 towns); chartered cities
of San Pablo, Antipolo, Tagaytay, Tanauan, Calamba, Sta. Rosa; Sto. Tomas and Malvar,
Batangas; Silang, Carmona and GMA, Cavite; Lucban, Quezon; Taguig and Pateros, Metro Manila;
chartered cities of Pasay, Caloocan, Quezon, Manila, Muntinlupa, Marikina and Pasig.
167
167
ANNEX C Guidelines for Safe Burial within Hospital Premises
Safe burial within the hospital premises shall be in accordance with the guidelines specified
in the DOH Health Care Waste Management Manual as follows:
1. Access to the disposal site should be restricted to authorized personnel only.
2. The burial site should be lined with a material of low permeability, such as clay, or geo-
membrane such as a high-density polyethylene (HDPE) plastic liner at the bottom of the
pit to prevent contaminating groundwater and avoid pollution.
3. Only hazardous health care waste should be buried. If general health care waste were
also buries on the premises, available space would be quickly filled-up.
4. Large quantities (>1kg) of chemical/pharmaceutical wastes should not be buried.
5. The burial site should be managed as a landfill, with each layer of waste covered with a
layer of earth to prevent odor, as well as to prevent proliferation of rodents and insects.
6. Burial site should not be located in flood prone areas.
7. Hospital ground should be secured. (e.g. fenced with warning signs).
8. The location of waste burial pit should be downhill or down-gradient from any nearby
wells and about 50 meters away from any water body such as rivers or lakes to prevent
contaminating sources of water.
9. Health care facilities should keep a permanent record of the size and location of all their
on-site burial pits to prevent construction workers, builders, and others from digging in
those areas in the future.
10. The safe burial of waste depends critically on rational operational practices. The bottom
of the pit should at least be 1.50 meters higher than the ground water level.
11. It should be noted that safe on-site burial practicable only for relatively limited period,
say 1 to 2 years, and for relatively small quantities of waste, say up to 5 to 10 tons in
total. Where these conditions are exceeded, a long-term solution will be needed.
168
168
ANNEXES
ANNEXES
ANNEX D Procedures for the Safe Burial of Sharps and Syringes through Concrete
Vault
The procedures for the safe burial of sharps and syringes though concrete vault shall be in
accordance with the guidelines in the DOH Health Care Waste Management Manual as follows:
1. Dig a pit (minimum size of 1m x 1m x 1.8m depth), enough to accommodate sharps and
syringes for an estimated period of time without reaching the groundwater level. The site
must be isolated and at least 152 meters away from the groundwater supply sources and
dwelling units.
2. Construct concrete walls and slabs of the pit. Provide slab opening or manhole for easy
deposition of collected sharps and syringes. The manhole should be extended a few
centimeters above the soil surface to overcome infiltration of surface water.
3. Deposit the collected safety boxes filled with used sharps and needles inside the concrete
vault.
4. Install a security fence around the site.
169
169
ANNEX
A nnex
I I
Bldg. No. 1, San Lazaro Compound, Rizal Avenue, Sta. Cruz, Manila 1003
Tel. Nos. (632)711-95-02, 711-95-03; Telefax (632) 743-18-29
July 30, 2008
ADMINISTRATIVE ORDER
No.2008 -0021
SUBJECT: Gradual Phase-out of Mercury in all Philippine Health Care

Facilities and Institutions
I. RATIONAL / BACKGROUND
Mercury is a naturally occurring heavy metal. At ambient temperature and pressure,

mercury is a silvery-white liquid that readily vaporizes and may stay in the atmosphere for up to a
year. When released to the air, mercury is transported and deposited globally. Mercury ultimately
accumulates in lake bottom sediments, where it is transformed into its more toxic organic form,
methyl mercury, which accumulates in fish tissue.
Mercury is highly toxic, especially when metabolized into methyl mercury. It may be fatal
if inhaled and harmful if absorbed through skin. Around 80% of the inhaled mercury vapour is
absorbed in the blood through the lungs. It may cause harmful effects to the nervous, digestive,
respiratory, immune system and to the kidneys, besides causing lung damage. Adverse health
effects from mercury exposure can be: tremors, impaired vision and hearing, paralysis, insomnia,
emotional instability, developmental deficit during fetal development, and attention deficit and
developmental delays during childhood.
In 1991, the World Health Organization (WHO) concluded that a safe level of mercury
exposure, below which no adverse effects, has never been established.
Several European countries Sweden, France, Denmark and Norway, have also banned
mercury-containing thermometers from as early as 1991. A European wide resolution on the issue
of mercury is pending.
In the Unites States, hospitals have significantly reduced the amount of mercury found in
facilities and are demonstrating a clear preference for safer alternatives. Many hospitals across the
country have taken steps to address the issue, including labelling mercury-containing devices and
phasing out their purchase in favour of safer, equally effective alternatives. More than 1,000
hospitals across the US have pledge to virtually eliminate mercury medical device and more than
90% of pharmacy chains have stopped selling mercury fever thermometers. Three of the five
largest healthcare group purchasing organizations in the US now have mercury-free purchasing
policies.
170
170
ANNEXES
ANNEXES
On 25 January 2006, at the opening of the First Southeast Asian Conference on Mercury in
Health Care held at the Philippine Heart Center, the Department of Health pronounce the gradual
elimination of mercury-use in the Philippine healthcare system.
The Department of Health (DOH) provides the following policies and guidelines for the
gradual phase-out of mercury in all Philippine health care facilities pursuant to, among others, the
following laws, rules and regulations:
Toxic Substances and Hazardous Nuclear Waste Control Act of 1990 (Republic Act
6969);
Procedural Manual for Title III: Hazardous Waste Management;
Management of Chemicals and Toxic Substances (Implementing Rules and
Regulations for Title II, DENR A.O. 92-09);
Chemical Control Order for Mercury and Mercury Compound (Implementing Rules
and Regulations under DENR A.O. 97-38);
Clean Water Act of 2004, (Republic Act No. 9275);
Policies and Guidelines on effective and proper handling, collection, transport,
treatment, storage and disposal of health care wastes, (Joint DOH-DENR
Administrative Order No. 02-2005)
Revised Rules and Regulations Governing the Registration, Licensure and Operation
of Hospitals and other Health Care Facilities in the Philippines (DOH Administrative
Order 70-A as amended);
Hospital Licensure Act (Republic Act No. 4226)
The Consumer Act of the Philippines of the Department of Trade and Industry (DTI),
covering various chemicals, Article 10-Injurious, Dangerous & Unsafe Products (RA
7394)
II. SCOPE AND COVERAGE
These policies and guidelines shall apply to all Health Care Facilities as defined by this
document.
III. DEFINITION OF TERMS
1. HEALTH CARE FACILITIES mean any of the following:
a. HOSPITALS place devoted primarily to the maintenance and operation of

facilities for the diagnosis, treatment and care of individuals suffering from illness,
disease, injury or deformity or in need of obstetrical or other medical and nursing
care. The term hospital shall also be construed as any institution, building or place
where there are installed beds or cribs or bassinets for twenty-four hour use or
longer by patients in the treatment of diseases, diseased-condition, injuries,
deformities or abnormal physical and mental states, maternity cases, and sanitorial
or sanitarial care infirmities, nurseries, dispensaries, and such other means by which
they may be designated.
b. INFIRMARY a health facility that provides treatment and care to the sick and
injured, as well as clinical care and management to mothers and newborn babies.
171
171
MANUAL ON
MANUAL ONHEALTHCARE
HEALTHCAREWASTE MANAGEMENT,
WASTE THIRD EDITION
MANAGEMENT, THIRD EDITION
c. BIRTHING HOME a health facility that provides maternity service on pre-natal

and post-natal care, normal spontaneous delivery and care of newborn babies.
d. CLINIC shall mean a place in which patients avail of medical consultations or

treatment on an out-patient basis and shall include the following:
d.1 Medical
d.2 Ambulatory
d.3 Dialysis
d.4 Health Care Centers and Dispensaries
d.5 Surgical
d.6 Alternative Medicine
d.7 Dental
d.8 Other clinical facilities not mentioned above that require a
license/certification/accreditation from DOH.
2. Mercury means any substance containing element mercury, either in its pure form, as
metallic salts or organometallic compounds.
3. Mercury Audit a mercury audit aims to identify all the uses and sources of mercury and
the amount present in the facility.
4. Alternatives to Mercury-containing devices/products mercury-reduced and mercury-

free products that are considered to be viable replacements for mercury containing
devices/products.
5. Hospital Waste Management Committee (HWMC) means a group in the Health Care
Facility with the overall responsibility of ensuring that health care wastes management
plan are promoted and implemented.
6. Waste Management Officer (WMO) means a person in the Health Care Facility
responsible for the day-to-day operation and monitoring of the waste management
system. In cases where the Health Care Facility has no HCWM, the WMO shall be the
person to assume the responsibility of ensuring the health care waste management plan of
the facility as promoted and implemented.
7. Mercury Minimization Program - means a gradual phase-out for the MDEP by a Health
Care Facility in accordance with Section V and following the management plan described
in Annex B of the Administrative Order.
IV. GENERAL PROVISIONS
Recognizing the unnecessary risks posed by the continued use of mercury containing
products in the healthcare system, the DOH hereby orders that:
1. All Hospitals shall immediately discontinue the distribution of mercury thermometers
to patients through the distribution of hospital admission/discharge kits.
2. All Hospitals shall follow the guidelines for the gradual phase-out of mercury in health
care facilities described in this document in the timeline period.
172
172
ANNEXES
ANNEXES
3. All new Health Care Facilities applying for a License to Operate shall submit an
inventory of all mercury-containing devices that will be used in their facilities and a
corresponding mercury elimination program.
4. All other Health Care Facilities other than hospital shall make a Mercury Minimization
Program based on the guidelines set by this administrative order.
V. GUIDELINES FOR THE GRADUAL PHASE-OUT OF MERCURY IN HEALTH

CARE FACILITIES
1. In order to ensure safety and contamination control, steps taken towards mercury
elimination in facility must be consistent and predetermined. It is therefore a must
to involve the whole facility in a dedicated Mercury Management and Minimization
Program, with the goal of:
a. Raising awareness on the dangers posed by mercury and mercury-containing
devices in all health care facilities and institutions.
b. Developing a clear preference for the use of Alternatives to Mercury-containing
Devices among health care personnel.
c. In the short term, preventing the further release of mercury to the environment
through proper disposal.
2. All Health Care Facilities are hereby tasked to designate a dedicated Mercury
Management Team within 2 months from the issuance of this order. This team
should be directly under the Hospital Waste Management Committee.
For the first 6 months from their inception, the Mercury Management Team should
have:
a. Conducted a Mercury Audit of their facility (Refer to Annex A Sample
Mercury Audit Form). This should include an assessment of the costs of
switching to alternatives to mercury-cointaining devices.
b. Developed and managed a Mercury Minimization Program for their facility
(Refer to Annex B Sample Mercury Minimization Program).
c. Drafted and implemented a purchasing policy that requires vendors to sign a
mercury-content disclosure agreement (Refer to Annex C Sample Vendor
Product Mercury-Content Disclosure) covering products intended for purchase.
A clear preference for Alternatives toe Mercury-containing Devices where
applicable should be in effect. Efforts should be made to communicate with
suppliers about an eventual mercury-free purchasing policy and to work with
staff on finding Alternatives to Mercury-containing Devices.
d. Conducted a facility-wide information campaign and employee education on
the consequences of continued mercury-use. Personnel training on preventing
and proper handling of mercury spills should be accomplished (Refer to Annex
D How to Handle Mercury Spills)
e. Identified and removed unnecessary practices that promote the use and
distribution of mercury-containing devices.
3. Within 24 months from the effectivity of this order, all hospitals should have
accomplished the following:
a. Fully implemented the Mercury Minimization Program developed for their
facility.
b. Switched to alternatives from mercury-containing devices.
c. Developed and implemented a program of waste segregation and recycling to
further reduce the mercury waste stream in cases where no alternative products
exist. For instance, mercury containing batteries and fluorescent light bulbs
should be collected and processed for recycling or should be properly stored.
173
173
d. Identified a dedicated mercury collection area within the facility.

e. Developed a proper temporary mercury storage room in the facility inaccessible
to the public (Refer to Annex E Guidelines for setting up a Proper Temporary
Mercury Storage Area).
f. Incorporated a mercury management module in their training program for new
personnel.
g. Information materials on mercury are displayed and/or available in their facility
for the benefit of their patients and the general public.
VI. EFFECTIVITY
This order shall take effect 30 Days after the publication in the Official Gazette and major
newspapers and shall supersede all issuance inconsistent herewith.
174
174
ANNEXES
ANNEXES
Annex j
ANNEX J
DEPARTMENT MEMORANDUM
No. 2011-0145
FOR : DIRECTORS, CHIEFS, HEALTH OFFICERS, ADMINISTRATIVE

OFFICERS AND HEALTHCARE WASTE MANAGEMENT
OFFICERSOF HOSPITALS AND OTHER HEALTH FACILITIES
SUBJECTS : Guidelines for the Temporary Storage of Mercury Wastes in Healthcare

Facilities in Accordance with Administrative Order No. 0021 s. 2008 on the
Gradual Phase-Out if Mercury in all Philippine Health Care Facilities and
Institutions
DATE : 11 April 2011

With heightened awareness of the dangers and risks of the use of mercury in health care
practices in recent years, DOH issued Administrative Order 0021, series 2008 or the Gradual Phase-Out
of Mercury in All Philippine Health Care Facilities and Institutions, dated July 30, 2008.
Ideally, mercury wastes or mercurial medical devices that are phased-out and are no longer
used should be transferred out of the health facilities and managed by treatment, storage and disposal
(TSD) facilities that are accredited by the Environmental Management Bureau (EMB) of the Department
of Environment and Natural Resources (DENR). However, there is yet no TSD facility developed and
accredited by the EMB-DENR for the elemental mercury found in mercurial thermometers and
sphygmomanometers, and it would take some time before these facilities are made available to health
facilities all over the country. Thus, providing the appropriate temporary storage conditions within the
health service facility and ensuring safe handling by healthcare personnel of the phased out medical
devices, including busted mercury lamps, become the responsibility of the DOH.
A study by Engr. Ana Rivera (DOH-National Center for Disease Prevention and Control) in
2007 showed that mercury vapour of the indoor air environment of 7 randomly selected tertiary hospitals
could be above the time-weighted average threshold limit value (TVL) of 25g/m3 for adults on 40-hour
workweeks. Using a Jerome 431X mercury vapour direct reading instrument ambient mercury levels
exceeded the TVL in and around loosely covered containers, receptacles and sinks that had been used for
disposing or washing broken thermometer glass and defective sphygmomanometers. When the odourless
and colorless elemental mercury vapor is inhaled, it readily enters the bloodstream and crosses the blood-
brain barrier, which is the most common mode of exposure to mercury.
To enhance patient safety measures in health care facilities, to protect health workers from the
potential hazards from mercury exposure and to minimize the accumulation of mercury in the
environment, all heads, chiefs and directors of healthcare facilities are hereby enjoined to refer to and
apply the Guidelines on Temporary Storage of Mercury-Containing Devices and Management of
Mercury Spills, as detailed in Annexes A and B of this Department Memorandum.
175
175
ANNEX A
GUIDELINES FOR THE TEMPORARY STORAGE OF
MERCURY-CONTAINING MEDICAL DEVICES AND MERCURY-CONTAINING WASTES
IN HEALTHCARE FACILITIES
I. Rationale
Mercury is a naturally occurring heavy metal that can harm human health. In healthcare
settings, it is most often observed in its liquid form in thermometers and sphygmomanometers. Liquid or
elemental mercury vaporizes in temperatures above 25 degrees Celsius.
People are exposed to mercury by breathing contaminated air, by accidental ingestion of
mercury compounds, and through direct contact with skin or the mucosa. Health effects from these kinds
of exposures are acute and can be directly linked to mercury exposure. On the other hand, chronic or
prolonged exposure to mercury can damage the central nervous system, cause chronic skin disorders and
reduce fertility. This occurs when food or water sources have been contaminated at levels that do not
produce immediate and alarming effects, or with prolonged exposure to mercury vapors. Case studies
have shown that mercury, once in the blood stream, can cross the blood-brain barrier and the placental
barrier as well. Mercury-related cases of severe neural or brain damage of foetuses that range from delay
in learning to walk to severe disabling neuromuscular disorders have been documented.
Thus, it is imperative that DOH issue these guidelines for the safe storage of mercurial
thermometers and blood pressure apparatuses and for the management of mercury spills if accidents
occur.
II. Scope of Application
This Department Memorandum applies to all types of healthcare facilities in the country.
Health care facilities include: hospitals, free-standing clinics, laboratories, various diagnostics and
treatment facilities.
III. Objectives
The General Objective is to provide guidance for appropriate temporary on-site storage of
mercury-containing medical devices and other mercury-containing waste materials in healthcare
facilities.
The Specific Objectives are:
1. Provide specifications for the establishment of the physical infrastructure for on-site
storage of mercury wastes
2. Describe the procedures for managing the storage of mercury
3. Describe the procedures for managing mercury spills
4. Redefine the functions of healthcare waste management committees in hospitals in
relation to the mercury phase-out policy
5. Prescribe the competencies and skills of healthcare staff to manage mercury clean-up and
temporary storage
6. Describe the monitoring scheme for the management of mercury-containing materials
and wastes in healthcare facilities
176
176
ANNEXES
ANNEXES
V. General Guidelines
1. These Guidelines shall apply to the following mercury-containing devices found in health
facilities:
a. mercury-containing body/fever thermometers
b. mercury-containing sphygmomanometers
c. mercury lamps
The above mercury-containing devices have known technically acceptable alternatives to
these that are widely available in the market.
2. All chief or heads of hospitals and outpatient clinics, and administrators of other health
facilities shall discontinue the purchase and use of them mercury-containing body/fever
thermometers and sphygmomanometers. In place of the mercurial thermometers, digital
thermometers are recommended. Instead of mercurial sphygmomanometers, aneroid
sphygmomanometers are recommended. Digital sphygmomanometers may also be used
in hospitals or specialty care units.
3. All chiefs or heads of hospitals and outpatient clinics and administrators of health
facilities other than hospitals shall ensure that mercury-containing thermometers and
sphygmomanometers are temporarily stored within the healthcare facility in a manner
that will pose the least risk to patients, clients and health personnel. They shall ensure
secure storage, and appropriate and timely disposal of used or busted mercury lamps in
their facilities through transport, storage and disposal (TSD) facilities that are accredited
by the Department of Environment and Natural Resources (DENR).
4. All health facilities shall register and secure a license from the Environmental
Management Bureau of DENR, according to the Joint DENR-DOH Administrative Order
No. 02, series of 2005, otherwise known as the Policies and Guidelines on Effective and
Proper Handling, Collection, Transport, Treatment, Storage and Disposal of Health Care
Wastes.
5. Heads of all health facilities shall be responsible for ensuring that there is a dedicated and
secure storage area for mercury wastes that shall be directly managed by a team of
designated and trained healthcare waste management officers or pollution control
officers.
6. The Healthcare Waste Management Committee (HCWMC) in each hospital facility shall
ensure the implementation of the guidelines described in this Department Memorandum.
For hospitals, at least two of the members if the HCWMC shall preferable by a medical
doctor, nurse or engineer and have the competencies required for the management of
mercury storage and spills which are the following:
a. Training in basic mercury management and
b. Training in basic life support and emergency response.
7. Licensing and accreditation of health facilities by PhilHealth shall be modified in order to
enforce the total phase-out of the use of mercury-containing thermometers and
sphygmomanometers and likewise, the appropriate installation and maintenance of proper
storage of mercury wastes within heath facility premises.
8. Heads of all DOH health facilities and heads of other government health facilities shall
shift to the purchase and use of compact fluorescent lamps and energy efficient lighting
systems in accordance with Administrative Order No. 183, Directing the Use of Energy
Efficient Lighting/Lighting Systems (EELS) in Government Facilities, from the office
of the President dated July 09, 2007.
9. Each DOH health facility shall allot funds from its MOOE for the implementation of
Administrative Order 0021, series 2008.
177
177
10. The National Center for Health Facility Development (NCHFD), National Center for
Disease Prevention and Control (NCDPC) and the Bureau of Health Devices and
Technology shall coordinate closely to provide technical assistance to health facility
managers, with approval from their Cluster Heads. The Centers for Health Development
(CHD) shall undertake periodic assessment of the implementation of Administrative
Order 0021, s. 2008 and this Department Memorandum by DOH-administered hospitals.
VI. Specific Guidelines
(The main reference used for the specific guidelines that follow is the Guidance on the
Cleanup, Temporary or Intermediate Storage and Transport of Mercury Waste from
Healthcare Facilities by the United Nations Development Programme-GEF Global
Healthcare Waste Project.)
1. Physical Infrastructure Requirements and Adaptation for On-Site Storage
1.1 Siting and Preparation:
1.1.1 The storage space should be located in a secure, restricted-access area away
from wards and other services areas, and not easily affected by floods.
1.1.2 If the storage space is in a multi-purpose building, it should be a locked
room or a locked partitioned space which cannot be easily entered or
accessed, in order to prevent theft of breakage of mercury containing
materials.
1.1.3 The storage space should be readily accessible to personnel who are
responsible for and authorized to collect, store, and transport wastes.
1.1.4 The exhaust vent of the storage space should direct air away from work
areas or from populated areas and should be far from any air intake vents.
1.1.5 Estimate the anticipated volume of mercury and mercury waste to be stored
and use this estimate to determine the minimum size of the storage space,
and the types and sizes of containers to be used.
1.1.6 Mercury waste should be segregated from regular waste, infectious waste,
and other types of healthcare wastes and from flammables.
1.2 Storage Space Design Requirements
1.2.1 The storage space should have roof and walls that protect the packed
devices from weather, insects or pests and other animals. If feasible, the
floor should have bunding or barriers.
1.2.2 The floor should be made of material that is smooth and impervious to
mercury. Examples of flooring materials that at impervious to mercury are:
polyurethane paint coated floor, seamless rubber, epoxy-coated cement and
polyester flooring.
1.2.3 The drain in the storage space should have an easily accessible and
replaceable drain trap to capture mercury in the event of a spill.
1.2.4 The storage access doors should have locks to render it inaccessible to the
public.
1.2.5 The storage space should have ventilation that can eject air from the space
directly to the outside and ventilation system that can prevent air circulation
from the storage space to the inside of the healthcare service areas.
1.2.6 Spill containment trays should be placed directly under the waste containers
or packages to catch spills if these occur and prevent them from spreading.
1.2.7 Personal Protective Equipment (PPE), a spill kit, and wash areas should be
located near (but not in) the storage space for easy access by authorized
personnel. The wash area should allow for eyewash and shower with
adequate water supply.
1.2.8 The storage space should be kept cool and dry, ideally below 25oC to
minimize volatilization of mercury.
178
178
ANNEXES
ANNEXES
1.2.8.1 Use air-conditioning and other cooling equipment only if it allows for
swift and adequate elimination of indoor air or vapors.
1.2.8.2 Cooling without the use of air-conditioning can be achieved through
the following:
a) Installation of ceiling fans, box fans or whole house fan with
timer)
b) Evaporative cooler to regulate humidity
c) Solar screens or heat-reflecting films and retractable awnings
over windows that are on the side of noonday sun.
d) Use of light colored paint because it absorbs less heat.
e) Maintenance of shady trees that could reduce external heat
around the storage areas (Choose hadry trees over those whose
limbs easily break.
f) Choosing roofing material that reduces ambient room
temperature.
1.2.8.3 If the volume of mercury wastes has been reduced adequately and
after these have been sealed in primary and secondary containers,
these can be refrigerated under the ideal temperature. Assign or
dedicate a refrigerator or cool box exclusively for mercury wastes.
Secure the refrigerator, cool box and other cooling equipment stably
inside the storage area.
1.2.9 Signage The entrance and exit doors of the storage space should be
marked with warning signs, such as Danger: Hazardous Mercury Waste
and the skull and crossbones symbol for toxic or poisonous wastes ()
2. Storage Procedures for Mercury Wastes
2.1 Storage of Elemental Mercury As a rule, keep elemental mercury intact inside
the original glass tubing of thermometers and sphygmomanometers. NEVER
extract the liquid mercury from thermometers. Only health personnel trained in the
maintenance of hospital equipment and medical devices wearing complete personal
protective equipment should attempt to dismantle sphygmomanometers.
2.1.1 As a redundant safety measure to prevent the release of mercury vapour,
ALWAYS use two containers, primary and secondary, to store elemental
mercury waste that has been collected from broken medical devices or
surrendered for safekeeping. Waste of this type primarily includes broken
glass or tubing tainted with mercury and also mercury-contaminated rags,
paper towels, pieces of carpet, slippers and other objects that have been
exposed or used for clean-up. Since intact mercurial thermometers and
sphygmomanometers which contain substantial amounts of elemental
mercury have the potential to be broken at any time during storage in the
health facility, these are also considered as hazardous wastes that should be
treated in the same manner as freed up or spilled elemental mercury (double
packing).
2.1.2 The primary and secondary containers should have the following
characteristics:
a) Easy-to-open and re-sealable
b) Leak-proof and air-tight
c) Puncture-proof and unbreakable
d) Made of material that does not react with or amalgamate with
mercury, such as plastic, wood or cardboard
e) Made of material that resists corrosion
f) Easy to lift or portable
g) Plastic wrappers and containers of clear and transparent material
179
179
2.1.3 A vapour suppression agent like sulphur powder, commercial absorbent

pads or water should be added to the primary container to protect health
staff in charge of collection and storage.
2.1.4 Perform the sealing off of mercury wastes into containers one after another
or double packaging over a plastic pan or basin or spill control tray in order
to catch any spill.
2.1.5 Label the primary container to indicate what type of mercury waste it
contains. The waste containers should be labelled Hazardous Mercury
Waste along with a description of the contents (what objects these are and
whether these are intact or broken); the initial date mercury was first placed
in the storage container and the identification of the waste generator or
name of the health facility:
HAZARDOUS MERCURY WASTE

Contents:___________________
Date Packed:________________
Generator:__________________
Address:___________________
If the secondary container is not transparent enough such that the label on
the primary container is not readable, a label should also be placed on the
second container.
2.1.6 Mercury waste containers that are meant to be stored for some time within
the health facility should be securely placed on top of a plastic pan, basic or
spill-control tray. The containment volume of the pan or tray should exceed
the total volume of liquid mercury stored in the container.
2.2 Storage of Mercury Lamps Unbroken fluorescent lamps are stored with the aim
to prevent breakage within the short period between storage and transfer to
accredited treatment, storage and disposal (TSD) facilities. Broken fluorescent
lamps, on the other hand, are stored as mercury-containing wastes, following
guideline no 2.1 (2.1.1 thru 2.1.5).
2.2.1 Unbroken lamps should be stored in a primary container that prevents
breakage, preferably the original box in which the lamps were shipped. If
the original box is not available, a box with a well-sealed vapour-resistant
liner, such as plastic foil liner, is recommended. Otherwise, a long box or
other box that fits the shape of the lamp can be used.
2.2.2 If the fluorescent lamps are stored in their original shipping cases or in a
box with vapour-resistant liner or in an approved fluorescent lamp or drum
container, there is no need for a secondary container.
2.2.3 If the fluorescent lamps need secondary containers, taped plastic sheets that
prevent the release of mercury vapour can be used. Labelling follows no.
2.1.4.
2.2.4 Stack up fluorescent lamps in a stable position. Stack them into adequately-
sized shelves that protect the entire length of the lamps or stand them up
into all plastic drums.
2.3 Management of the Mercury Storage Area
2.3.1 All personnel involved in collection, storage, on-site transport and
supervision of mercury waste should have training in mercury waste
management and spill cleanup.
2.3.2 General rules for safe maintenance of the storage area are:
2.3.2.1 There should be no smoking or eating in and around the storage
area.
180
180
ANNEXES
ANNEXES
2.3.2.2 Regular pest and vermin control program should be instituted for the
storage area to ensure that packed mercury wastes are not tampered
with, and that no contaminated pests bring out mercury out if the
storage area.
2.3.2.3 Inspect the storage space at least once a month to check for leaks,
corroded or broken containers, improper methods of storage,
ventilation, condition of PPEs and wash area, spill kit contents and
records.
2.3.2.4 The chair of the healthcare waste management committee or the
head of the healthcare facility should keep updated about
information on the availability of Environmental Management
Bureau (EMB)-accredited treatment, storage and disposal facilities
for elemental mercury (in thermometers and sphygmomanometers)
that can serve his/her respective health facility, and coordinate the
transfer of accumulated mercury waste in the soonest possible time.
2.3.2.5 Inventory records should be kept of the types of mercury waste,
description, quantities in storage and initial dates of storage. The
date of inspections, findings and name of inspector should also be
recorded. Information in this inventory record will be used to fill-up
the hazardous waste registration form of the DENR-EMB prior to
transport of the mercury waste outside the health facility.
A sample inventory record logbook and its entries are shown below:
Date of Initial Specific Area- Type of Mercury Quantity Description (intact
Storage Source On-Site Waste (specify unit) or broken)
Date of Inspection Findings Actions Taken Recommendations Name & Signature

of Inspector
3. Management of Mercury Spills The main purpose of managing mercury spills in a

healthcare facility is to minimize the exposure of patients, health workers and the
surrounding community to the hazardous health and environmental effect of mercury.
3.1 The first information to gather about mercury spills is the estimated volume of
mercury spilled. Large spills are spills estimated to be more than two tablespoons.
In case of a large spill, do the following:
3.1.1 Inform the highest ranking officer/s available in the facility of the incident.
3.1.2 Seal off ALL possible points of exit of mercury vapors in the storage area
and cordon off the premises.
3.1.3 Organize for the immediate evacuation of patents and healthcare workers.
Be sure that people leaving the site had not stepped on mercury by directing
them away from the spill site. Those who have come in contact with
mercury should be directed to the nearest safe location and stay there until
clean up and decontamination procedures have been instituted.
3.1.4 NO health facility personnel, not even the members of the Healthcare Waste
Management Committee should clean up the spill. Seek professional
assistance.
3.1.5 Call the nearest fire department of the local government or Bureau of Fire
Protection (Department of Interior and Local Government) to manage the
large spill.
181
181
Small Spills can be managed by designated members of the healthcare waste

management committee, pollution control officer or other health personnel who
have had training in mercury spill management.
3.2 Management procedures for small spills have the following components:
(1) Preparation prior to a spill event; (2) Cleanup Procedure during mercury
spill; and, (3) Post-exposure Monitoring. The step-by-step procedures for the above
components are described in Annex B.
4. Monitoring Mercury Management in Healthcare Facilities
4.1 On-Site Monitoring by Healthcare Facility Managers or Healthcare Waste
Management Committee The on-site monitoring checklist should include the
parameters enumerated below.
4.1.1 On a daily basis, visit the storage site to:
4.1.1.1 Check integrity of the storage access doors and enclosures
4.1.1.2 Check for evidence of intrusion of vermin or pests and unauthorized
personnel
4.1.1.3 Regulate cooling and air vent systems
4.1.2 On a monthly basis, inspect the storage site for:
4.1.2.1 Presence of leaks, corroded or broken containers
4.1.2.2 Methods of storage
4.1.2.3 Ventilation and condition of cooling systems
4.1.2.4 Condition and completeness of PPE
4.1.2.5 Condition and completeness of spill kit
4.1.2.6 Functionality of wash area
4.1.2.7 Timeliness of records
4.1.2.8 Immediate necessary actions on observed problems
4.1.3 The composition of the on-site monitoring team of hospitals and other large
healthcare facilities should include any 3 (three) or more of the following:
4.1.3.1 Chief of Clinics or Chief of Medical Professional Staff
4.1.3.2 Chief Administrative Officer
4.1.3.3 Patient Safety Officer
4.1.3.4 Supply Officer
4.1.3.5 Health Facility Engineer
4.1.3.6 Pollution Control Officer
4.1.3.7 Waste Management Officer
4.2 Monitoring by the Department of Health The National Center for Health
Facility Development (NCHFD) shall design a rapid assessment checklist or guide
for the periodic assessment by DOH Central Office managers and managers of the
Centers for Health Development (CHD) of the implementation of Administrative
Order 2008-0021 and this Department Memorandum.
All healthcare facilities keeping or storing mercury-containing thermometers and
sphygmomanometers and other mercury wastes should implement these guidelines as soon as possible in
order to reduce the risk of spilling mercury into the environment and to protect the health of its workers
and clients. The initiative to phase-out the use of mercury-containing devices is relatively new in the
country, but as soon as better technology and resources are available for the purpose, the Department of
Health will keep its partners in health care informed through similar appropriated issuances.
182
182
ANNEXES
ANNEXES
ANNEX B
Management of Mercury Spill
1. Pre-Spill Preparations
a. The Mercury Spill Response Team shall be trained and organized to respond to
a mercury spill.
b. The senior staff involved in the clean up shall:
i. Ensure that the contents of the kit are complete at any point in time.
ii. Monitor the expiration dates of the contents of the spill kits.
c. A minimum of two sets of spill kits shall be made available in a designated
secured and accessible place outside the mercury storage area.
d. The component of the spill kits are listed in Box 1, below.
Box 1: Components of a Mercury Spill Kit

1) Step-by-step instructions (on laminated paper)
2) Personal protective equipment (PPE):
(a) Several pairs of rubber or nitrile gloves
(b) Safety goggles or protective eyewear
(c) Respiratory protection (full-tested, full- or half-face piece, air-
purifying respirator with mercury vapor cartridges, or a face
mask with a 0.3 micron HEPA filter to capture amalgam particles
and mercury-laden dust (However, it should be noted that
regular masks do not protect against mercury vapour.)
(d) Coveralls, apron, and other protective clothing
(e) Disposable shoe covers or booties
3) Containers:
(a) Air-tight, sealable, plastic bags (ziplock)
(b) Small, air-tight, rigid clear plastic container with non-metal cover
(c) Air-tight, puncture-resistant, rigid plastic or steel jar or container
with a wide opening for collecting mercury-contaminated broken
glass
(d) Plastic tray
(e) Small transparent bags, 2 to 6 mils or 50 to 150 microns thick
HDPE-high density polyethylene
4) Tools for removing mercury:
(a) Flash light to locate shiny mercury beads
(b) Plastic-coated playing cards or index cards, cardboards to scoop
mercury beads
(c) Small plastic scoop or plastic dust pan to catch mercury beads
(d) Tweezers to remove small broken glass pieces
(e) Eyedropper or syringe (without needle) to draw up large mercury
beads
(f) Duct tape or sticky tape to pick up tiny mercury droplets
(g) Vapour suppression agents: Sulphur powder to absorb mercury
by forming mercuric sulphide; toothpaste; brush to remove
mercury-sulphur dust
(h) Utility knife blade
5) Materials for spill site decontamination
(a) Hydrogen peroxide and cotton swabs for final cleaning
(b) Alkaline soap and paper towels
(c) Decontamination solution
6) Materials for Decontamination of Response Team
(a) Water, alkaline soap and basin to contain water from
(b) Robe, towel and clean clothes to be used after decontamination
and shower
7) Danger: Mercury Waste labels to put on waste containers
183
183
2. Clean-up Procedures During Mercury Spill

In case of an actual spill, a step-by-step cleanup procedure shall be followed as
indicated in this Annex. The enumerated Steps 1 to 20 shall be posted near the entrance
of the storage site.
Step 1: Quickly determine the extent of the spill

Determine on what surfaces that mercury spilled and how far the mercury beads travelled.
Check mercury beads in crevices (in floors, walls, junctions).
Step 2: Immediately block off the contaminated area
If the extent of a small spill is not immediately obvious, cordon off the area with a radius of
about 2 meters around the center of the spill.
Step 3: Evacuate the area
Check to see if anyones skin, shoes or clothing was splashed with mercury. Remove all
contaminated clothing or shoes which should be left in the spill area. Have everyone else
leave the area; dont let anyone walk through the mercury spill on their way out. Give
priority to pregnant women and children.
Seek assistance to provide first-aid to anyone requiring immediate medical attention.
Contaminated skin should be washed with alkaline soap and water.
Step 4: Contain the spill
If necessary, prevent the mercury beads from travelling further by blocking the path with
rags or impervious material. Take steps to keep mercury from falling into drains or cracks.
Step 5: Minimize the spread of vapors to interior areas
Close all interior doors that lead to the other indoor areas. Turn off central ventilation,
exhaust and air-conditioning systems that circulate from the spill site to other areas of the
building.
Step 6: Reduce vapor concentrations in the spill area if possible
For small spills, open all windows and external doors to dilute the vapor concentrations in
the room. Prevent access to spill areas by putting up signs and then leave the area to
prepare for cleanup.
Step 7: Prepare for cleanup
Remove jewelry, watch, cellular phones and other metal-containing items. Get hold of the
mercury spill kit.
Step 8: Put on personal protective equipment (PPE)
Put on the apron, or coveralls, disposable shoe covers, rubber or nitrile gloves, goggles,
and face mask before re-entering the spill site. Make sure metal items such as eyeglass
frames are covered by PPE.
Step 9: Remove visible mercury beads and broken glass
Place the jar containers on the plastic tray. Starting from the outside of the spill site and
moving towards the center, carefully remove visible mercury beads and broken glass. Use
tweezers to remove broken glass pieces and place them in a jar or wide-mouthed
container over the tray. Using playing cards, cardboards or index cards, slide the mercury
beads onto the plastic dustpan or similar receptacle and scoop away from any porous
surface. Use slow sweeping motions to keep mercury from becoming uncontrollable.
Carefully place the mercury beads into the plastic container partially filled with water. Do
this over the tray to catch any spillage. An eyedropper or syringe for small beads can be
used. Hold the eyedropper or syringe almost parallel to the floor to draw in the beads and
keep the eyedropper or syringe horizontal when transferring the beads to the plastic
container so as to prevent the mercury from falling out.
184
184
ANNEXES
ANNEXES
Step 10: Search for and remove tiny mercury droplets and glass
Look for remaining mercury droplets and glass pieces by shining flashlight, holding it at a
low angle close to the floor in a darkened room and look for additional glistening beads of
mercury that may be sticking to the surface or in small cracked areas of the surface. Put
toothpaste on top of a small paint brush and gently dot the affected area to pick up
smaller hard-to-see beads. Duct tapes can also be used to pick up these small droplets.
Place the tape or paintbrush in a sealable plastic bag.
Step 11: Clean up cracks and hard surface
Sprinkle sulphur powder on cracks and crevices and on hard surfaces that have come in
contact with mercury. A color changes in the powder from yellow to reddish brown
indicates that mercury is still present and more cleanup is necessary. Use the brush to
remove the powder and place them in the sealable bag. Clean the hard surface with
hydrogen-soaked swabs and place the swabs in a sealable plastic bag.
Step 12: Remove contaminated soft materials
Use the utility knife to cut out pieces of soft materials such as curtains and bedding that
are contaminated with mercury. Place the contaminated materials in a sealable plastic
bag.
Step 13: Clean out contaminated drains
If the mercury was spilled over a drain, sink or wash basin, work with the facility engineer
to remove and replace the J, U, or S trap. Put a plastic tray under the work area to
catch any mercury that might spill out. Hold the old trap over a tray while transferring the
mercury to the air-tight container. Dispose of the old trap as hazardous waste.
Step 14: Dispose or decontaminate cleanup material
Place all contaminated materials used during the cleanup into leak-proof, sealable plastic
bag or transparent bags.
Step 15: Label and seal all contaminated material
Check that the air-tight jar and container are filled with enough water to cover the
elemental mercury and broken glassware. The jar or container shall be tightly sealed,
properly labelled and placed individually in re-sealable bags. Place all sealed plastic bags
with mercury-contaminated waste inside a second plastic bag, seal the outer bag using
duct tape and affix a label such as Mercury: Hazardous Waste and include a brief
description of the contents. Send the bags to the temporarily on-site storage area.
Step 16: Remove and dispose decontaminated PPE
Remove PPE beginning with the shoe covers which should be placed in another sealable
bag. Then remove the gloves by grasping one glove with the other, peeling off the first
glove, sliding the fingers under the remaining glove at the wrist, peeling off the second
glove, and discarding both gloves in the sealable plastic bag. Next, remove goggles by the
head band or ear pieces. Remove the apron or coverall without touching the front and turn
inside out. Finally, remove the face mask or respirator without touching the front. Dispose
of the gloves, shoe covers, apron and regular face mask if used in lieu of a specialty mask
in the sealable plastic bag which should be stored together with the mercury waste.
Decontaminate gloves and respirators using decontamination solution.
Step 17: Do self-decontamination
1. Proceed to the designated decontamination or wash area.
2. Take a bath using alkaline soap and water to decontaminate all exposed skin.
3. Change to clean clothes.
Step 18: Ventilate the spill area
Place a fan next to the spill area to volatilize mercury and a second fan aimed towards a
window or doorway to move air to the outside air for 48 hours or more. If this is not
185
185
possible due to central heating or air conditioning, increase the air exchange rate for the
building for several days to reduce any mercury vapour concentrations.
Step 19: Medical monitoring
If the spill resulted in acute exposure to a patient or health worker, refer the patient to
hospitals with capability for toxicology services.
Step 20: Write a report on the spill incident
Document the incident in keeping with the procedures of the health facility. The report can
be used to improve safety in the facility. The HEARS Field Report form by the Health
Emergency Management Staff of the DOH is recommended to be used for this report.
Box 2: The following should NOT be done in the event of a spill:
Do not use a vacuum cleaner to pick up the mercury and

mercury-contaminated items. The mercury will become airborne
by way of the vacuums exhaust and spread the contamination.
Moreover, the vacuum cleaner will become contaminated and
would have to be disposed as hazardous waste.
Do not wash mercury-contaminated clothing, rugs or other

fabrics in a washing machine. The washing machine and
wastewater may become contaminated.
Do not use a broom to sweep up the mercury. It can break the

mercury into smaller beads, spreading them.
Do not pour mercury down the drain. You may contaminate

your plumbing, septic system, or your local sewage treatment
plant.
Do not spread mercury that has gotten onto your shoes. If

possible, clean the shoes with the decontaminant solution. If
the shoes cannot be decontaminated wrap them in a plastic bag
and dispose of them properly.
3. Post-Exposure Monitoring
a. For further evaluation, referral should be made to the DENR-EMB Regional
Office, the East Avenue Medical Center or to the DOLE-Occupational Safety and
Health Center to perform ambient air mercury monitoring. This will guide
decision-making with regards need for further cleanup.
b. Medical monitoring shall be done for a patient, healthcare worker or responder
with acute exposure, by conducting a medical examination which includes urine
and blood mercury determination. Appropriate treatment shall be done in case of
frank poisoning. Proper referral to a nearest poison control center shall be
performed for advice and further medical management.
186
186
ANNEXES
ANNEXES
Box 3: First Aid Measures
Inhalation:
Move exposed person/s to fresh air. If not breathing, give artificial
respiration. If breathing is difficult, give oxygen. Get medical
attention immediately.
Ingestion:
Do not induce vomiting. Never give anything by mouth to an
unconscious person. Get medical attention immediately.
Skin Contact:
Immediately flush skin with plenty of water for at least 15 minutes
while removing contaminated clothing and shoes. Use alkaline soap
to facilitate washing. Get medical attention immediately. Wash
clothing before reuse. Thoroughly clean shoes before reuse.
Eye Contact:
Immediately flush eyes with plenty of water for at least 15 minutes,
lifting lower and upper eyelids occasionally. Get medical attention
immediately.
187
187
References
AEA Technology, Metro Manila Solid Waste Management Project Final Report
ADB, September 2003
American Society for Hospital engineering: Safety Policies and Procedures for
Healthcare Facilities by John S. Klare, 1992
Asian Institute of Technology: Healthcare Waste in Asia: Intuitions and Insights,
2008
Basel Convention on the Control of the Trans-boundary Movements of Hazardous
Wastes and Their Disposal (1989)
BFAD Memorandum Circular No. 22 Series of 1994, Inventory, Proper Disposal
and/or Destruction of Used Vials or Bottles and BFAD Bureau Circular No.
16 Series of 1999: Amending BFAD MC No. 22 dated September 8, 1994,
Regarding Inventory, Proper Disposal and/or Destruction of Used Vials or Bottles
Center for Disease Control and Prevention: Handwashing: Clean Hands Save
Lives http://www.cdc.gov/handwashing/
DENR Administrative Order No. 34 Series 1990 Revised Water Usage and
Classification/ Water Quality Criteria Amending Section Nos. 68 and 69, Chapter
III of the 1978 NPCC Rules and Regulations
DENR Administrative Order No. 35, Series 1990, Effluent Regulations
DENR Administrative Order No. 36, Series 2004, Revising DENR Administrative
Order No. 29, Series 1992, to Further Strengthen the Implementation of Republic
Act 6969 and Prescribing the Use of the Procedural Manual
DOH-DENR Joint Administrative Order No. 02 series of 2005 dated August
24, 2005 entitled Policies and Guidelines on effective and Proper Handling,
Collection, Transport, Treatment, Storage, and Disposal of HCW
DOH Administrative Order No. 70-A series of 2002 Revised Rules and
Regulations Governing the Registration, Licensure, and Operation of Hospitals
and Other Health Facilities in the Philippines
DOH Administrative Order No. 2005-0029 dated December 12, 2005,
Amendment to Administrative Order No. 70-A series of 2002 re: Revised
Rules and Regulations Governing the Registration, Licensure and Operation of
Hospitals and Other Health Facilities in the Philippines
DOH Administrative Order No. 2007-0014, Guidelines on the Issuance of
Certificate of Product Registration for Equipment or Devices Used for Treating
Sharps, Pathological and Infectious Waste
DOH Administrative Order No. 2007-0027 dated August 22, 2007 Revised Rules
and Regulations Governing the Licensure and Regulation of Clinical Laboratories
in the Philippines
DOH Administrative Order No. 2008-0021 dated July 30, 2008, Gradual Phase
out of Mercury in all Philippine Healthcare Facilities and Institutions
188
REFERENCES
DOH Administrative Order No. 2008-0023 dated July 30, 2008, National Policy
on Patient Safety
DOH Administrative Order 2010-0033 Revised Implementing Rules and
Regulations of PD 856 Code on Sanitation of the Philippines Chapter XXI
Disposal of Dead Persons December 2010
DOH Department Memorandum 2011-0145, Guidelines for the Temporary
Storage of Mercury Wastes in HCF in Accordance with AO No. 0021 s. 2008
on the Gradual Phase-out of Mercury in All Philippine Healthcare Facilities and
Institutions
DOH Healthcare Waste Management Manual in 2004 (Revising the 1997
Hospital Waste Management Manual)
DOH: Operation Manual on the Rules and Regulations Governing Domestic
Sludge and Septage, June 2008
Executive Order No. 301 (2004) Establishing a Green Procurement Program
for All Departments, Bureaus, Offices, and Agencies of the Executive Branch of
Government
ISO 14001 Environmental Management Guide
Kyoto Protocol to the United Nations Framework Convention on Climate Change
(1997)
McCay, P.H., Ocampo-Sosa, A.A. & Fleming, G.T.A. (2010). Effect of
subinhibitory concentrations of benzalkonium chloride on the competitiveness of
Pseudomonas aeruginosa grown in continuous culture. Microbiology 156: 30-38
Montreal Protocol on Substances that Deplete the Ozone Layer (1987)
PNRI Administrative Order 1990-0001: Radioactive Wastes by Philippine Nuclear
Research Institute (PNRI) from Off-Site Waste Generators
Philhealth Benchbook for Quality Assurance in Healthcare (2006)
Presidential Decree 813 (1975) and Executive Order 927 (1983). Strengthening
the Functions of LLDA
Presidential Decree 856 The Code on Sanitation of the Philippines Chapter
XVII on Sewage Collection and Excreta Disposal (1976)
Presidential Decree No. 984 Providing for the Revision of Republic Act No.
3931, Commonly Known as the Pollution Control Law, and for Other Purposes
(1976)
Presidential Decree No. 1586 Environmental Impact Statement (EIS) System
(1978)
Republic Act No. 4226 Hospital Licensure Act (1965)
Republic Act No. 6969 - An Act to Control Toxic Substances and Hazardous and
Republic Act No. 8749 - The Philippine Clean Air Act of 1999
Republic Act No. 9003 - Ecological Solid Waste Management Act of 2000
Republic Act 9275 The Philippine Clean Water Act of 2004
Sanez , Geri Geronimo: Healthcare Waste Management in the Philippines, for
the Thematic Working Group on Solid and Hazardous Wastes, 2008
189
Scientific Applications International Corporation: Life Cycle Assessment:

Principles and Practice, 2006
Stockholm Convention on Persistent Organic Pollutants (2001)
UN: Globally Harmonized System of Classification and Labeling of Chemicals
(GHS) Third Revised Edition, 2009
United Nations Framework Convention on Climate Change (1997)
WB Water and Sanitation Program: Philippine Sanitation Sourcebook and
Decision Aid, 2005
WHO: Safe Management of Wastes from Healthcare Activities, 1999
WHO: Safe Management of Wastes from Healthcare Activities, draft second
edition
WHO: Practical Guidelines for Infection Control in Healthcare Facilities, 2004
WHO: Laboratory Safety Manual Third Edition, 2004
WHO: Guidance Manual for the Preparation of National Healthcare Waste
Management Plans in Sub-Saharan Countries
WHO: Guidelines for the Safe Use of Wastewater, Excreta, and Greywater
Volume II Waste Water Use in Agriculture, 2006
World Health Organization:
http://www.who.int/gpsc/5may/How_To HandWash_Poster.pdf
http://www.who.int/gpsc/5may/How_To_HandRub_Poster.pdf
WHO: Risks and Costs Associated With the Management of Infectious Wastes
by L.F. Diaz and G.M. Savage, 2003
WHO:Philippines: Environmental Health and country Profile, 2005
190
191
Manual on
Healthcare Waste
Management
Third Edition
2012
192

Health Care Waste Management Manual 3rd Ed

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Health Care Waste Management Manual 3rd Ed

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Health Care Waste Management Manual 3rd Ed

Uploaded by

Copyright:

Available Formats

Department of Health

Access to affordable, quality and responsive healthcare services and facilities is

Now, the challenge of each and every healthcare facility is to minimize,

ENRIQUE T. ONA, MD. FPCS, FACS

These considerations led to the preparation of the 3rd Edition Manual on

Our international development partners: Mr. Renaud Meyer, Country Director,

TECHNICAL WORKING GROUP

Ms. Eleonorita Reyes

Engr. Aida Calma

Administrative and Secretarial Support

CONTRIBUTORS AND RESOURCE PERSONS

Dr. Mario C. Villaverde Undersecretary of Health

Dr. Epifania S. Simbul Corazon Locsin Montelibano Memorial

United Nations Development Programme

Department of Environment and Natural Resources

De La Salle Medical Center, Dasmarinas, Cavite

PART 1: GENERAL CONSIDERATIONS AND OVERVIEW

CHAPTER 2: HEALTHCARE WASTE AND ITS IMPACT

CHAPTER 3: LEGISLATIONS, POLICIES AND GUIDELINES

PART II: HEALTHCARE WASTE MANAGEMENT SYSTEM

CHAPTER 4: WASTE MINIMIZATION

CHAPTER 5: SEGREGATON, COLLECTION, STORAGE AND

CHAPTER 6: WASTE TREATMENT AND DISPOSAL SYSTEM

CHAPTER 7: MANAGING WASTEWASTER GENERATED BY

PART III: ADMINISTRATIVE CONTROLS AND REQUIREMENTS

CHAPTER 8: ADMINISTRATIVE REQUIREMENTS

CHAPTER 9: HEALTH AND SAFETY PRACTICES

PART IV: GLOSSARY, ANNEXES AND REFERENCES

Table 2.1 Categories of Healthcare Waste 9

Figures 1.1 Chain of Infection 4

5.7 Sample Central HCW Storage for Hazardous and 60

Annex A World Health Organization Technical Guidelines 146

HCF : Healthcare Facility/ies

PET : Polyethylene Terephthalate

1.2 Purpose and Intent

1.3 Scope and Limitations

1.4 Contents of the Manual

Part I includes the general description of HCW, an overview, categories,

Some components of HCW are potential reservoir of disease-causing microorganisms

Reservoir Mode of Transmission

Figure 1.1 Chain of Infection

1.6.2 Hierarchy of Controls

Engineering Control is used to remove a hazard or place a barrier between the

a) Patient Safety which includes proper patient identification, assurance of blood

Figure 1.2 Healthcare Waste Management Hierarchy

1.7 Expected Outcome

Chapter 2: Healthcare Waste and its Impact

Diagnosis, treatment or immunization of human beings;

Hospitals and medical centers

2.2 Categories of Healthcare Waste

Table 2.1 Categories of Healthcare Waste

CATEGORY DESCRIPTION EXAMPLES

Infectious All waste suspected to contain pathogens Solid wastes from

Discarded materials or equipment used Liquid wastes from

Highly infectious waste include microbial Food wastes (liquid or

Except syringes and

Anatomical waste is a subgroup of Amputated body parts

CATEGORY DESCRIPTION EXAMPLES