SAFETY DATA SHEET

Mystik Hydraulic Jack Oil

Section 1. Identification
GHS product identifier : Mystik Hydraulic Jack Oil
Synonyms : Hydraulic oil
Code : 663321002
MSDS # : 663321002

Supplier's details : CITGO Petroleum Corporation

P.O. Box 4689
Houston, TX 77210
[email protected]

Emergency telephone : Technical Contact: (800) 248-4684

number Medical Emergency: (832) 486-4700
CHEMTREC Emergency: (800) 424-9300
(United States Only)

Section 2. Hazards identification

OSHA/HCS status : While this material is not considered hazardous by the OSHA Hazard Communication
Standard (29 CFR 1910.1200), this SDS contains valuable information critical to the
safe handling and proper use of the product. This SDS should be retained and available
for employees and other users of this product.
Classification of the : Not classified.
substance or mixture

GHS label elements

Signal word : Warning
Hazard statements : Injection under the skin can cause severe injury.
Most damage occurs in the first few hours.
Initial symptoms may be minimal.
Precautionary statements
General : Avoid contact with eyes, skin and clothing. May be harmful if swallowed. IF IN EYES:
Rinse cautiously with water for several minutes. IF SWALLOWED: Do NOT induce
vomiting. After handling, always wash hands thoroughly with soap and water. If you feel
unwell, seek medical attention and show the label when possible. Keep out of reach of
children.
Prevention : Not applicable.
Response : Not applicable.
Storage : Store in a dry place and/or in closed container. Store in accordance with all local,
regional, national and international regulations.
Disposal : Dispose of contents and container in accordance with all local, regional, national and
international regulations.
Hazards not otherwise : Injection of petroleum hydrocarbons requires immediate medical attention
classified

Section 3. Composition/information on ingredients

Substance/mixture : Mixture
Other means of : Hydraulic oil
identification

CAS number/other identifiers

CAS number : Not applicable.

Date of issue/Date of revision : 11/24/2014. Date of previous issue : No previous validation. Version :1 1/9
Mystik Hydraulic Jack Oil

Section 3. Composition/information on ingredients

Any concentration shown as a range is to protect confidentiality or is due to process variation.

There are no ingredients present which, within the current knowledge of the supplier and in the concentrations
applicable, are classified as hazardous to health or the environment and hence require reporting in this section.
Occupational exposure limits, if available, are listed in Section 8.

Section 4. First aid measures

Description of necessary first aid measures
Eye contact : Immediately flush eyes with plenty of water, occasionally lifting the upper and lower
eyelids. Check for and remove any contact lenses. Get medical attention if irritation
occurs.
Inhalation : Remove victim to fresh air and keep at rest in a position comfortable for breathing. Get
medical attention if symptoms occur.
Skin contact : Flush contaminated skin with plenty of water. Remove contaminated clothing and
shoes. Get medical attention if symptoms occur.
Ingestion : Wash out mouth with water. Remove victim to fresh air and keep at rest in a position
comfortable for breathing. Do not induce vomiting unless directed to do so by medical
personnel. Get medical attention if symptoms occur.

Most important symptoms/effects, acute

Potential acute health effects
Eye contact : No known significant effects or critical hazards.
Inhalation : No known significant effects or critical hazards.
Skin contact : Injection of pressurized hydrocarbons can cause severe permanent tissue damage.
Initial symptoms may be minor.
Ingestion : No known significant effects or critical hazards.
Over-exposure signs/symptoms
Eye contact : No specific data.
Inhalation : No specific data.
Skin contact : No specific data.
Ingestion : No specific data.

Indication of immediate medical attention and special treatment needed, if necessary

Notes to physician : Treat symptomatically. Contact poison treatment specialist immediately if large
quantities have been ingested or inhaled.
Specific treatments : Treat symptomatically and supportively.
Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training.

See toxicological information (Section 11)

Section 5. Fire-fighting measures

Specific hazards arising : In a fire or if heated, a pressure increase will occur and the container may burst.
from the chemical

Extinguishing media
Suitable extinguishing : Use an extinguishing agent suitable for the surrounding fire.
media
Unsuitable extinguishing : None known.
media
Hazardous thermal : No specific data.
decomposition products

Date of issue/Date of revision : 11/24/2014. Date of previous issue : No previous validation. Version :1 2/9
Mystik Hydraulic Jack Oil

Section 5. Fire-fighting measures

Special protective actions : Promptly isolate the scene by removing all persons from the vicinity of the incident if
for fire-fighters there is a fire. No action shall be taken involving any personal risk or without suitable
training.
Special protective : Fire-fighters should wear appropriate protective equipment and self-contained breathing
equipment for fire-fighters apparatus (SCBA) with a full face-piece operated in positive pressure mode.

Section 6. Accidental release measures

Personal precautions, protective equipment and emergency procedures
For non-emergency : No action shall be taken involving any personal risk or without suitable training.
personnel Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilled material. Put on appropriate personal
protective equipment.
For emergency responders : If specialised clothing is required to deal with the spillage, take note of any information
in Section 8 on suitable and unsuitable materials. See also the information in "For non-
emergency personnel".

Environmental precautions : Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).

Methods and materials for containment and cleaning up

Small spill : Stop leak if without risk. Move containers from spill area. Dilute with water and mop up
if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and
place in an appropriate waste disposal container. Dispose of via a licensed waste
disposal contractor.
Large spill : Stop leak if without risk. Move containers from spill area. Prevent entry into sewers,
water courses, basements or confined areas. Wash spillages into an effluent treatment
plant or proceed as follows. Contain and collect spillage with non-combustible,
absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in
container for disposal according to local regulations (see Section 13). Dispose of via a
licensed waste disposal contractor. Note: see Section 1 for emergency contact
information and Section 13 for waste disposal.

Section 7. Handling and storage

Precautions for safe handling
Protective measures : Put on appropriate personal protective equipment (see Section 8).
Advice on general : Eating, drinking and smoking should be prohibited in areas where this material is
occupational hygiene handled, stored and processed. Workers should wash hands and face before eating,
drinking and smoking. Remove contaminated clothing and protective equipment before
entering eating areas. See also Section 8 for additional information on hygiene
measures.

Conditions for safe storage, : Store in accordance with local regulations. Store in original container protected from
including any direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials
incompatibilities (see Section 10) and food and drink. Keep container tightly closed and sealed until
ready for use. Containers that have been opened must be carefully resealed and kept
upright to prevent leakage. Do not store in unlabeled containers. Use appropriate
containment to avoid environmental contamination.
Bulk Storage Conditions: Maintain all storage tanks in accordance with applicable
regulations. Use necessary controls to monitor tank inventories. Inspect all storage
tanks on a periodic basis. Test tanks and associated piping for tightness. Maintain the
automatic leak detection devices to assure proper working condition.

Date of issue/Date of revision : 11/24/2014. Date of previous issue : No previous validation. Version :1 3/9
Mystik Hydraulic Jack Oil

Section 8. Exposure controls/personal protection

Control parameters
Occupational exposure limits
None identified.

Appropriate engineering : Good general ventilation should be sufficient to control worker exposure to airborne
controls contaminants.
Environmental exposure : Emissions from ventilation or work process equipment should be checked to ensure
controls they comply with the requirements of environmental protection legislation. In some
cases, vapor controls, filters or engineering modifications to the process equipment will
be necessary to reduce emissions to acceptable levels.

Individual protection measures

Hygiene measures : Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Wash contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Eye/face protection : Safety glasses equipped with side shields are recommended as minimum protection in
industrial settings. If contact is possible, the following protection should be worn, unless
the assessment indicates a higher degree of protection: Splash goggles. Safety
eyewear complying with an approved standard should be used when a risk assessment
indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts.
If inhalation hazards exist, a full-face respirator may be required instead.
Skin protection
Hand protection : Chemical-resistant gloves complying with an approved standard should be worn at all
times when handling chemical products if a risk assessment indicates this is necessary.
Body protection : Personal protective equipment for the body should be selected based on the task being
performed and the risks involved and should be approved by a specialist before
handling this product.
Other skin protection : Appropriate footwear and any additional skin protection measures should be selected
based on the task being performed and the risks involved and should be approved by a
specialist before handling this product.
Respiratory protection : Use a properly fitted, air-purifying or supplied-air respirator complying with an approved
standard if a risk assessment indicates this is necessary. Respirator selection must be
based on known or anticipated exposure levels, the hazards of the product and the safe
working limits of the selected respirator.

Section 9. Physical and chemical properties

Physical state : Liquid.
Color : Red.
Odor : Mild petroleum odor
pH : Not available.
Boiling point : Not available.
Flash point : Open cup: >100C (>212F) [Estimated]
Evaporation rate : <1 (n-butyl acetate. = 1)
Lower and upper explosive : Not available.
(flammable) limits
Vapor pressure : Not available.
Vapor density : >1 [Air = 1]
Relative density : 0.9
Density lbs/gal : Estimated 7.5 lbs/gal
Gravity, API : Estimated 26 @ 60 F
Solubility : Insoluble in the following materials: cold water.

Date of issue/Date of revision : 11/24/2014. Date of previous issue : No previous validation. Version :1 4/9
Mystik Hydraulic Jack Oil

Section 9. Physical and chemical properties

Viscosity : Kinematic (40C (104F)): 0.22 cm2/s (22 cSt)
Viscosity SUS : Estimated 110 SUS @104 F

Section 10. Stability and reactivity

Reactivity : Not expected to be Explosive, Self-Reactive, Self-Heating, or an Organic Peroxide
under US GHS Definition(s).

Chemical stability : The product is stable.

Possibility of hazardous : Under normal conditions of storage and use, hazardous reactions will not occur.
reactions

Conditions to avoid : No specific data.

Incompatible materials : No specific data.

Hazardous decomposition : Under normal conditions of storage and use, hazardous decomposition products should
products not be produced.

Section 11. Toxicological information

Information on toxicological effects
Acute toxicity
Conclusion/Summary : Distillates (petroleum), hydrotreated heavy naphthenic: Mineral oil mists derived
from highly refined oils are reported to have low acute and sub-acute toxicities in
animals. Effects from single and short-term repeated exposures to high concentrations
of mineral oil mists well above applicable workplace exposure levels include lung
inflammatory reaction, lipoid granuloma formation and lipoid pneumonia. In acute and
sub-acute studies involving exposures to lower concentrations of mineral oil mists at or
near current work place exposure levels produced no significant toxicological effects.
Irritation/Corrosion
Skin : No additional information.
Eyes : No additional information.
Respiratory : No additional information.
Sensitization
Skin : No additional information.
Respiratory : No additional information.
Mutagenicity
Conclusion/Summary : No additional information.

Carcinogenicity
Conclusion/Summary : No additional information.
Reproductive toxicity
Conclusion/Summary : No additional information.
Teratogenicity
Conclusion/Summary : No additional information.
Specific target organ toxicity (single exposure)
Not available.
Specific target organ toxicity (repeated exposure)
Not available.
Aspiration hazard
Not available.
Date of issue/Date of revision : 11/24/2014. Date of previous issue : No previous validation. Version :1 5/9
Mystik Hydraulic Jack Oil

Section 11. Toxicological information

Information on the likely : Routes of entry anticipated: Dermal.

routes of exposure
Potential acute health effects
Eye contact : No known significant effects or critical hazards.
Inhalation : No known significant effects or critical hazards.
Skin contact : Injection of pressurized hydrocarbons can cause severe permanent tissue damage.
Initial symptoms may be minor.
Ingestion : No known significant effects or critical hazards.

Symptoms related to the physical, chemical and toxicological characteristics

Eye contact : No specific data.
Inhalation : No specific data.
Skin contact : No specific data.
Ingestion : No specific data.

Potential chronic health effects

General : No known significant effects or critical hazards.
Carcinogenicity : No known significant effects or critical hazards.
Mutagenicity : No known significant effects or critical hazards.
Teratogenicity : No known significant effects or critical hazards.
Developmental effects : No known significant effects or critical hazards.
Fertility effects : No known significant effects or critical hazards.

Section 12. Ecological information

Toxicity
Conclusion/Summary : Not available.

Persistence and degradability

Conclusion/Summary : Not available.

Bioaccumulative potential
Not available.

Mobility in soil
Soil/water partition : Not available.
coefficient (KOC)

Other adverse effects : No known significant effects or critical hazards.

Section 13. Disposal considerations

Disposal methods : The generation of waste should be avoided or minimized wherever possible. Disposal
of this product, solutions and any by-products should at all times comply with the
requirements of environmental protection and waste disposal legislation and any
regional local authority requirements. Dispose of surplus and non-recyclable products
via a licensed waste disposal contractor. Waste should not be disposed of untreated to
the sewer unless fully compliant with the requirements of all authorities with jurisdiction.
Waste packaging should be recycled. This material and its container must be disposed

Date of issue/Date of revision : 11/24/2014. Date of previous issue : No previous validation. Version :1 6/9
Mystik Hydraulic Jack Oil

Section 13. Disposal considerations

of in a safe way. Empty containers or liners may retain some product residues. Avoid
dispersal of spilled material and runoff and contact with soil, waterways, drains and
sewers.

Section 14. Transport information

DOT Classification IMDG IATA
UN number Not regulated. Not regulated. Not regulated.

UN proper - - -
shipping name
Transport - - -
hazard class(es)

Packing group - - -
Environmental No. No. No.
hazards
Additional - - -
information

Special precautions for user : Transport within users premises: always transport in closed containers that are
upright and secure. Ensure that persons transporting the product know what to do in the
event of an accident or spillage.

Transport in bulk according : Not available.

to Annex II of MARPOL
73/78 and the IBC Code

Section 15. Regulatory information

U.S. Federal regulations : United States inventory (TSCA 8b): All components are listed or exempted.
Clean Water Act (CWA) 307: Zinc and zinc compounds
This material is classified as an oil under Section 311 of the Clean Water Act (CWA)
and the Oil Pollution Act of 1990 (OPA). Discharges or spills which produce a visible
sheen on waters of the United States, their adjoining shorelines, or into conduits leading
to surface waters must be reported to the EPA's National Response Center at (800)
424-8802.

SARA 302/304
Composition/information on ingredients
SARA 304 RQ : Not applicable.
SARA 311/312
Classification : Not applicable.
Composition/information on ingredients

State regulations
Massachusetts : None of the components are listed.
New York : None of the components are listed.
New Jersey : None of the components are listed.
Pennsylvania : None of the components are listed.

Date of issue/Date of revision : 11/24/2014. Date of previous issue : No previous validation. Version :1 7/9
Mystik Hydraulic Jack Oil

Section 15. Regulatory information

International regulations
International lists : Australia inventory (AICS): All components are listed or exempted.
China inventory (IECSC): All components are listed or exempted.
Japan inventory: Not determined.
Korea inventory: All components are listed or exempted.
Malaysia Inventory (EHS Register): Not determined.
New Zealand Inventory of Chemicals (NZIoC): All components are listed or exempted.
Philippines inventory (PICCS): All components are listed or exempted.
Taiwan inventory (CSNN): Not determined.
Canada inventory : All components are listed or exempted.
EU Inventory : At least one component is not listed in EINECS but all such components are listed in
ELINCS.
Please contact your supplier for information on the inventory status of this material.
WHMIS (Canada) : Not controlled under WHMIS (Canada).

Section 16. Other information

National Fire Protection Association (U.S.A.)

1 Flammability
Health 0 0 Instability/Reactivity
Special

Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency
Response Copyright 1997, National Fire Protection Association, Quincy, MA 02269. This reprinted material is
not the complete and official position of the National Fire Protection Association, on the referenced subject
which is represented only by the standard in its entirety.
Copyright 2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to
be interpreted and applied only by properly trained individuals to identify fire, health and reactivity hazards of
chemicals. The user is referred to certain limited number of chemicals with recommended classifications in
NFPA 49 and NFPA 325, which would be used as a guideline only. Whether the chemicals are classified by NFPA
or not, anyone using the 704 systems to classify chemicals does so at their own risk.
History
Date of issue/Date of : 11/24/2014.
revision
Key to abbreviations : ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL 73/78 = International Convention for the Prevention of Pollution From Ships,
1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution)
UN = United Nations
Notice to reader
THE INFORMATION IN THIS SAFETY DATA SHEET (SDS) WAS OBTAINED FROM SOURCES WHICH WE BELIEVE
ARE RELIABLE. HOWEVER, THE INFORMATION IS PROVIDED WITHOUT ANY WARRANTY, EXPRESSED OR
IMPLIED REGARDING ITS CORRECTNESS OR ACCURACY. SOME INFORMATION PRESENTED AND
CONCLUSIONS DRAWN HEREIN ARE FROM SOURCES OTHER THAN DIRECT TEST DATA ON THE SUBSTANCE
ITSELF. THIS SDS WAS PREPARED AND IS TO BE USED ONLY FOR THIS PRODUCT. IF THE PRODUCT IS USED
AS A COMPONENT IN ANOTHER PRODUCT, THIS SDS INFORMATION MAY NOT BE APPLICABLE. USERS
SHOULD MAKE THEIR OWN INVESTIGATIONS TO DETERMINE THE SUITABILITY OF THE INFORMATION OR
PRODUCTS FOR THEIR PARTICULAR PURPOSE OR APPLICATION.

THE CONDITIONS OR METHODS OF HANDLING, STORAGE, USE, AND/OR DISPOSAL OF THE PRODUCT ARE
BEYOND OUR CONTROL AND MAY BE BEYOND OUR KNOWLEDGE. FOR THIS AND OTHER REASONS, WE DO
NOT ASSUME RESPONSIBILITY AND EXPRESSLY DISCLAIM LIABILITY FOR ANY LOSS, DAMAGE OR EXPENSE
Date of issue/Date of revision : 11/24/2014. Date of previous issue : No previous validation. Version :1 8/9
Mystik Hydraulic Jack Oil

Section 16. Other information

ARISING OUT OF OR IN ANY WAY CONNECTED WITH HANDLING, STORAGE, USE OR DISPOSAL OF THE
PRODUCT.
Mystik is a registered trademark of CITGO Petroleum Corporation

Date of issue/Date of revision : 11/24/2014. Date of previous issue : No previous validation. Version :1 9/9