Set#3:

1.

Which OSI layer does IP rely on to determine whether packets have been lost and to
request retransmission?

application

presentation

session

transport

2.

Refer to the exhibit. Which layered network model is shown in the diagram?
Cisco
IETF
OSI
TCP/IP

3.

Refer to the exhibit. The diagram represents the process of sending e-mail between clients. Which list correct
identifies the component or protocol used at each numbered stage of the diagram?
1.MUA 2.MDA 3.MTA 4.SMTP 5.MTA 6.POP 7.MDA 8.MUA
1.MUA 2.POP 3.MDA 4.SMTP 5.MTA 6.MDA 7.SMTP 8.MUA
1.MUA 2.POP 3.SMTP 4.MDA 5.MTA 6.SMTP 7.POP 8.MUA
1.MUA 2.SMTP 3.MTA 4.SMTP 5.MTA 6.MDA 7.POP 8.MUA

4.

A user enters http://www.cisco.com/web1.htm in the address line of a browser. Which

statement is true about this transaction?
The "http" portion indicates the protocol that is being used.
The "web1.htm" portion is the specific service name.
 The retrieved web page will be displayed in URL code.
The "www.cisco.com" is the name of the web page file that is called.

5.

Which range of port numbers are reserved for services that are commonly used by applications
that run on servers?
0 to 255
0 to 1023
1024 to 49151
49152 to 65535

6.

Which OSI layer addressing is required to route packets between two networks?
Layer 1
Layer 2
Layer 3
Layer 4

7.

When connectionless protocols are implemented at the lower layers of the OSI
model, what is usually used to acknowledge that the data was received and to
request the retransmission of missing data?

IP

UDP

Ethernet

a connectionless acknowledgement

an upper-layer, connection-oriented protocol or service

8.

Which statement is true about Layer 3 addresses?

They are physical addresses.
They are used in routing decisions.
 They are only used on local networks.
They are altered each time a packet crosses a router.

9.

Which option shows the PDU that contains the Layer 3 source and destination addressing for a
packet?

10.

Refer to the exhibit. Host A sends 1000 bytes of Telnet data to host B. What does host B send back if it only
receives the first 500 bytes?
Source 23 Destination 49321 Seq 1000 Ack 500
Source 23 Destination 49321 Seq 500 Ack 1000
Source 23 Destination 49321 Seq 500 Ack 500
Source 23 Destination 49321 Seq 1000 Ack 501
Source 23 Destination 49321 Seq 501 Ack 1000
Source 23 Destination 49321 Seq 501 Ack 501
11.

Refer to the exhibit. In a network, PC1 sends a message to PC2. The frame received at PC2 is shown. What
information in this frame determines the correct destination application?
timing and synchronization bits
destination and source physical addresses
destination and source logical network addresses
destination and source process numbers
12.
What three statements are true about network layer addressing? (Choose three.)
Network layer addressing uses a hierarchy.
It uses addresses that are 48 bits in length.
It is used by Ethernet switches to make forwarding decisions.
It does not support broadcasts.
It uses a method by which the network portion of an address can be identified.
Network layer addressing identifies each host distinctly.

13.

Which device should be used for enabling a host to communicate with another host on a different
network?
switch
hub
router
host
14.

Refer to the exhibit. Host A attempts to establish a TCP/IP session with host C. During this
attempt, a frame was captured with the source MAC address 0050.7320.D632 and the destination
MAC address 0030.8517.44C4. The packet inside the captured frame has an IP source address
192.168.7.5, and the destination IP address is 192.168.219.24. At which point in the network was
this packet captured?
leaving host A
leaving ATL
leaving Dallas
leaving NYC

15.

Refer to the exhibit. When computer A sends a frame to computer D, what computers receive the
frame?
only computer D
only computer A and computer D
only computer B, computer C, and computer D
all computers
16.
 What type of network is maintained if a server takes no dedicated role in the network?
mainframe
client/server
peer-to-peer
centralized

17.

Refer to the exhibit. Assume all devices are using default configurations. How many subnets are
required to address the topology that is shown?
1
3
4
5
7

18.

Refer to the exhibit. Which type of network design is shown?

client/server
wide area
dedicated server
peer-to-peer

19.

Refer to the exhibit. Host A is accessing multiple servers. Which combination of port
number and address will uniquely identify a particular process running on a specific server?
MAC address of the server and port number of the service
IP address of the host and port number of the service
MAC address of the host and port number of the service
IP address of the server and port number of the service
20.

A network technician is tasked with setting up a network for six users, but the users should be
able to use their accounts to log on from any of the six computers. What type of network should
be used?
workgroup
 P2P applications
peer-to-peer network
client-server network

21.

What are three characteristics of CSMA/CD? (Choose three.)

Devices can be configured with a higher transmission priority.
A jam signal indicates that the collision has cleared and the media is not busy.
A device listens and waits until the media is not busy before transmitting.
The device with the electronic token is the only one that can transmit after a collision.
All of the devices on a segment see data that passes on the network medium.
After detecting a collision, hosts can attempt to resume transmission after a random time
delay has expired.

22.

Which of the following are the address ranges of the private IP addresses? (Choose three.)
10.0.0.0 to 10.255.255.255
200.100.50.0 to 200.100.25.255
150.150.0.0 to 150.150.255.255
172.16.0.0 to 172.31.255.255
192.168.0.0 to 192.168.255.255
127.16.0.0 to 127.31.255.255

23.

Refer to the exhibit. What function does router RT_A need to provide to allow Internet access
for hosts in this network?
address translation
DHCP services
ftpd
web server
24.

Refer to the exhibit. A network technician is trying to determine the correct IP address
configuration for Host A. What is a valid configuration for Host A?
IP address: 192.168.100.19; Subnet Mask: 255.255.255.248; Default Gateway: 192.16.1.2
IP address: 192.168.100.20; Subnet Mask: 255.255.255.240; Default Gateway:
192.168.100.17
IP address: 192.168.100.21; Subnet Mask: 255.255.255.248; Default Gateway:
192.168.100.18
IP address: 192.168.100.22; Subnet Mask: 255.255.255.240; Default Gateway: 10.1.1.5
IP address: 192.168.100.30; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.1.1

25.

Refer to the exhibit. Host C is able to ping 127.0.0.1 successfully, but is unable to communicate
with hosts A and B in the organization. What is the likely cause of the problem?
Hosts A and B are not on the same subnet as host C.
The IP addresses on the router serial interfaces are wrong.
The subnet mask on host C is improperly configured.
The FastEthernet interface fa0/0 of router 1 is wrongly configured.

26.
What happens when a host station receives a frame that contains its own MAC address in the destination
The Layer 2 information is removed and the frame is pushed up to Layer 3.
The host station will copy the information to its buffers and send it back out.
The frame originated from the host and will be ignored.
The Layer 3 information is added to the frame.
27.

Refer to the exhibit. A network administrator is troubleshooting a link that is down between
Router1 and Router2. To correct the problem, which wire pairs need to be switched on one of
the Ethernet cable ends?
pair 1 and pair 2
pair 1 and pair 3
pair 2 and pair 3
pair 2 and pair 4

28.

Refer to the exhibit. PC1 is unable to access PC2. To troubleshoot this problem, the
technician needs to confirm that the next hop interface is operational. Which default gateway
address should the technician ping from PC1 to confirm this?
10.0.0.254
192.168.0.249
192.168.0.250
10.0.1.254

29.
Which combination of network id and subnet mask correctly identifies all IP addresses from 172.16.128.0
through 172.16.159.255?
172.16.128.0 255.255.255.224
172.16.128.0 255.255.0.0
172.16.128.0 255.255.192.0
172.16.128.0 255.255.224.0
172.16.128.0 255.255.255.192
30.

Refer to the exhibit. Host A wants to connect to host B on a different network. Which three
IP addresses can be assigned to host A to enable this connectivity? (Choose three.)
172.16.11.36
172.16.11.95
172.16.11.88
172.16.11.70
172.16.11.64
172.16.11.67

31.
A user sees the command prompt: Router(config-if)# . What task can be performed at this
mode?
Reload the device.
Perform basic tests.
Configure individual interfaces.
Configure individual terminal lines.

32.
Which password is automatically encrypted when it is created?
vty
aux
console
enable secret
 enable password
33.
Which router component will have contents erased when the command erase startup-config
flash
RAM
ROM
NVRAM
34.
A technician is asked to secure the privileged EXEC mode of a switch by requiring a password. Which ty
password would require this login and be considered the most secure?
console
enable
enable secret
VTY

35.

Which exhibit shows the interface that is configured by the command, router(config)# interface
serial 0/0/1?

36.

When must a router serial interface be configured with the clock rate command?
when the interface is functioning as a DTE device
when the interface timers have been cleared
when the connected DTE device is shut down
when the interface is functioning as a DCE device

37.
What can the user do from the command prompt, Router(config-line)# ?
Configure one of the network interfaces.
Configure one of the physical or virtual lines.
Verify the running configuration on the device.
Configure the parameters for one of the routing protocols.

38.

Due to a security violation, the router passwords must be changed. What information can be
learned from the following configuration entries? (Choose two.)

Router(config)# line vty 0 3

Router(config-line)# password c13c0
Router(config-line)# login

The entries specify three Telnet lines for remote access.

The entries specify four Telnet lines for remote access.
The entries set the console and Telnet password to "c13c0".
Telnet access will be denied because the Telnet configuration is incomplete.
Access will be permitted for Telnet using "c13c0" as the password.

39.

Which prompt represents the appropriate mode used for the copy running-config startup-
config command ?
Switch-6J>
Switch-6J#
Switch-6J(config)#
Switch-6J(config-if)#
Switch-6J(config-line)#

40.

Refer to the exhibit. An employee wants to access the organization intranet from home. Which
intermediary device should be used to connect the organization intranet to the Internet to enable
this access?
hub
switch
 router
wireless access point

41.

Refer to the exhibit. A PC is communicating with another PC on a remote network. The two
networks are connected by three routers. Which action will help to identify the path between the
hosts?
Use the ipconfig command at the host.
Use the ipconfig/all command at the destination.
Use the tracert command at the host.
Use the ping command at the destination.

42.

Refer to the exhibit. RouterB is configured properly. The Ethernet interface Fa0/0 of RouterA is
configured with the use of the commands that are shown. However, a ping from the Fa0/0
interface of RouterA to the Fa0/0 interface of RouterB is unsuccessful. What action should be
taken on RouterA to solve this problem?
Use the description command on the FastEthernet interface Fa0/0.
Configure the clock rate of the FastEthernet interface Fa0/0.
Use the no shutdown command on the FastEthernet interface Fa0/0.
Reboot the router.

3.

Which physical connector type is used for a serial V.35 connection to the CSU/DSU?

44.
 What information can be gathered by using the command netstat?
the default gateway
the routing protocol
active TCP connections
the locally configured subnet mask

45.

Refer to the exhibit. Each media link is labeled. What type of cable should be used to connect the
different devices?
Connection 1 - rollover cable
Connection 2 - straight-through cable
Connection 3 - crossover cable
Connection 1 - crossover cable
Connection 2 - rollover cable
Connection 3 - crossover cable
Connection 1 - straight-through cable
Connection 2 - crossover cable
Connection 3 - crossover cable
Connection 1 - straight-through cable
Connection 2 - crossover cable
Connection 3 - straight-through cable
Connection 1 - crossover cable
Connection 2 - straight-through cable
Connection 3 - crossover cable

46.

Refer to the exhibit. A network administrator remotely accesses the CLI of RouterB from PC1
using Telnet. Which statement is true about this connection?
The data is automatically encrypted.
A Telnet server process is running on PC1.
The connection is made through a VTY session on the router.
A GET request was sent to RouterB to retrieve data during this session.

47.
Refer to the exhibit. The tracert command is initiated from PC1 to PC4. Which device will send
a response to the initial tracert packet from PC1?
Athens
Ankara
London
Paris
PC4

48.

Refer to the exhibit. Host A is transmitting data to host B. Which address combination will be
used as the data leaves the Router1 Fa0/1 interface?
Destination IP: 192.168.72.2 Source MAC: 0007.C2B4.3421
Destination IP: 192.168.10.4 Source MAC: 0030.8596.DE81
Destination IP: 192.168.10.4 Source MAC: 0007.C2B4.3421
Destination IP: 192.168.72.2 Source MAC: 0030.8596.DE81

49.

Refer to the exhibit. While configuring a network, a technician wired each end of a Category 5e
cable as shown. Which two statements are true about this setup? (Choose two.)
The cable is suitable for connecting a switch to a router Ethernet port.
The cable is suitable for connecting dissimilar types of devices.
The cable is unusable and must be rewired.
The cable is terminated in a way that the transmit pin is wired to the receive pin.

50.

Refer to the exhibit. The ping 127.0.0.1 command is issued on the local host. What do the ping
results indicate?
The local host can send packets on the local network.
The TCP/IP stack on the local host operates properly.
The local host has full connectivity to the default gateway.
The local host has full connectivity to the remote network.