B Tech Civil Syllabus PDF

H.P.
TECHNICAL UNIVERSITY
HAMIRPUR (HP)
Syllabus
[Effective from the Session: 2012-13]
B. Tech. (Civil Engineering)
Group A contain: Civil Engineering (CE)
Information Technology (IT)
Electronics and Communication Engg. (ECE)
Computer Science and Engg. (CSE)
Group A
1st Semester Scheme and Distribution of Marks
Course Subject L T P/D Hrs Theory Practical Total

No. End Sessional End Sessional
Semester Semester
NS-101 Engineering Mathematics I 3 1 0 4 100 50 150
NS-102 Engineering Physics-I 3 1 0 4 100 50 150
NS-103 Engineering Chemistry 3 1 0 4 100 50 150
HS-102 Communication and Professional Skills in 3 1 0 4 100 50 150
English
BE-102 Basic Mechanical Engineering 3 1 0 4 100 50 150
BE-104 Principles of Computer Programming & C++ 3 1 0 4 100 50 150
(Practicals / Drawing / Design)
NS-103 (P) Engineering Chemistry Laboratory 0 0 2 2 25 25 50

HS-102 (P) Communication and Professional Skills Lab-I 0 0 2 2 25 25 50
BE-104 (P) Computer Programming Laboratory 0 0 2 2 25 25 50
WS-101 Workshop Practice-I 0 0 3 3 25 25 50
Total 33 600 300 100 100 1100
Group A
2nd Semester Scheme and Distribution of Marks
Course Subject L T P/D Hours Theory Practical Total

Semester Semester
NS-104 Engineering Mathematics-II 3 1 0 4 100 50 150
NS-105 Engineering Physics-II 3 1 0 4 100 50 150
HS-101 Disaster Management and Environmental 3 1 0 4 100 50 150
Science
BE-101 Basic Electrical and Electronics Engineering 3 1 0 4 100 50 150
BE-103 Engineering Drawing and Graphics 1 0 5 6 100 50 150
BE-105 Engineering Mechanics 3 1 0 4 100 50 150
NS-105 (P) Engineering Physics Lab 0 0 2 2 25 25 50
BE-101a (P) Basic Electrical Engineering Lab 0 0 2 2 25 25 50
BE-101b (P) Basic Electronics Engineering Lab 0 0 2 2 25 25 50
WS-102 Workshop Practice-II 0 0 3 3 25 25 50
Total 35 600 300 100 100 1100
1
Civil Engineering
3rd Semester Scheme and Distribution of Marks
Course No. Subject L T P/D Hrs Theory Practical Total

End Sessional End Sessional
Semester Semester
HS-201 Engineering Economics 3 0 0 3 100 50 150
CE-211 Strength of Materials 3 1 0 4 100 50 150
CE-212 Building Construction and Materials 3 1 0 4 100 50 150
CE-213 Fluid Mechanics 3 1 0 4 100 50 150
CE-214 Surveying-I 3 1 0 4 100 50 150
NS-206 Engineering Mathematics-III 3 1 0 4 100 50 150
(Practical / Drawing / Design)
CE-212 (P) Building Material Laboratory 0 0 2 2 25 25 50
CE-213(P) Fluid Mechanics Laboratory 0 0 2 2 25 25 50
CE-214(P) Surveying-I Laboratory 0 0 2 2 25 25 50
CE-215(P) Building Drawing 0 0 2 2 25 25 50
HS-202 (P) Oral and Written Communication 0 0 2 2 25 25 50
Skills Lab-II
Total 33 600 300 125 125 1150
Civil Engineering
4th Semester

Semester Semester
HS-203 Human values and professional Ethics 2 0 2 4 100 50 150
NS-207 Numerical Methods for Engineers 3 1 0 4 100 50 150
CE-221 Structural Analysis-I 3 1 0 4 100 50 150
CE-222 Geotechnical Engineering-I 3 1 0 4 100 50 150
CE-223 Hydropower and Fluid Machines 3 1 0 4 100 50 150
CE-224 Surveying-II 3 1 0 4 100 50 150
CE-222(P) Soil Mechanics Laboratory 0 0 2 2 25 25 50
CE-223(P) Hydropower and Fluid Machines 0 0 2 2 25 25 50
Laboratory
CE-224(P) Surveying-II Laboratory 0 0 2 2 25 25 50
ECA-201 Extra Curricular Activity 0 0 2 2 25 25 50
Total 32 600 300 100 100 1100
Field Visit shall be compulsory to all students of 2nd year once in a year during or after 4th semester.
Survey camp of minimum four (4) weeks duration shall be conducted after 4th Semester for Civil
Engineering students. For students of other branches community project at this level will be conducted be
included. The Evaluation of same shall be done during 5th Semester.
2
Civil Engineering
5th Semester
Course Subject L T P/D Hours Theory Practical Total
No.
End Sessional End Sessional
Semester Semester
HS-301 Principles of Management and Critical 3 0 2 5 100 50 150
Thinking
CE-311 Structural Analysis-II 3 1 0 4 100 50 150
CE-312 Design of Concrete Structures 3 1 0 4 100 50 150
CE-313 Geotechnical Engineering-II 3 1 0 4 100 50 150
CE-314 Hydrology and Groundwater 3 1 0 4 100 50 150
CE-315 Transportation Engineering-I 3 1 0 4 100 50 150
CE-311(P) Structural Analysis Laboratory 0 0 2 2 25 25 50
CE-312(P) Concrete Laboratory 0 0 2 2 25 25 50
HS-300 Community Project/ Survey Camp 0 0 0 0 50 50 100
Total 31 600 300 100 100 1100
Civil Engineering
6th Semester

Semester Semester
**-300(*) Open Elective 3 0 0 3 100 50 150
CE-321 Bridge Engineering 3 1 0 4 100 50 150
CE-322 Irrigation Engineering 3 1 0 4 100 50 150
CE-324 Transportation Engineering-II 3 1 0 4 100 50 150
CE-350 Water Supply and System Engineering 3 1 0 4 100 50 150
CE-326 Estimation and Costing 3 1 0 4 100 50 150
CE-320(P) Civil Engineering Software Laboratory -I 0 0 3 3 25 25 50
CE-324(P) Transportation Engineering Laboratory 0 0 2 2 25 25 50
CE-350(P) Environmental Engineering Laboratory 0 0 2 2 25 25 50
Total 30 600 300 75 75 1050
$$ - Industrial Training of 8 weeks duration after 6th Semester

Open Elective to be opted from list below but one which is not offered by his Department
Sr. No. Open Elective Sub. Code

1. Energy Assessment and Auditing EE-300
2. Total Quality Management ME-300
3. Optimization methods for Engineering System NS-300
4. Remote Sensing & GIS CE-300
5. Operating Systems CS-300
3
Civil Engineering
7th Semester
Course Subject L T P/ Hrs Theory Practical Total

No. D End Sessional End Sessional
Semester Semester
CE-411(*) Elective-I 3 1 0 4 100 50 150
CE-412 Design of Steel Structures 3 1 0 4 100 50 150
CE-413 Design of Hydraulic Structures 3 1 0 4 100 50 150
CE-414 Waste and Sewage Treatment 3 1 0 4 100 50 150
CE-415 Project Planning and Construction 3 1 0 4 100 50 150
Equipments
CE-412(P) Structural Drawing 0 0 3 3 50 50 100
CE-414(P) Waste and Sewage Treatment 0 0 2 2 25 25 50
Laboratory
CE-496 Industrial Training Viva $$ 0 0 0 0 50 50 100
CE-497 Seminar 0 0 2 2 -- 50 50
CE-498 Project-I 0 0 6 6 100 50 150
Total 33 500 250 225 225 1200
During winter break there shall be a field visit compulsory to all students of 7th semester, 4th year.
Elective-I
CE-411 (a) Prestressed Concrete
CE-411(b) - Finite Element Methods in Civil Engineering
CE-411 (c) Open Channel Flow
8th Semester
Course No. Subject L T P/ Hrs Theory Practical Total

D End Sessional End Sessional
Semester Semester
CE-421(*) Elective-II 3 1 0 4 100 50 150
CE-422 Advanced Structural Design 3 1 0 4 100 50 150
CE-423 Water Resources and System Engineering 3 1 0 4 100 50 150
CE-424 Earthquake Resistant Design 3 1 0 4 100 50 150
CE-420 Civil Engineering Software Laboratory -II 0 0 2 2 25 25 50
CE-499 Project-II 0 0 6 6 100 50 150
GP-500 General Proficiency 0 0 0 0 100 -- 100
Total 24 400 200 225 75 900
Elective-II
CE-421 (a) Rock Mechanics
CE-421 (b) Remote Sensing and G I S
CE-421 (c) - Repair and Rehabilitation of Structures
Total theory marks = 6750

Total practical marks = 1950
Grand total = 8700
4
Engineering Mathematics-I (NS-101)
Course Code NS-101 Credits- 04 L - 3, T- 1, P - 0

Name of Course Engineering mathematics-I
Lectures to be delivered 52 (L-39, T-13 for each semester)
Semester End Examination MM: 100 Min. Marks; 40 Time Allowed: 3 Hrs.
Continue Assessment (based on sessional tests 50%) Tutorial/ Assignment: MM: 50.
30%, Quiz/ Seminar: 10 %, Attendance: 10 %.
Instructions
1. The question paper will consist of five sections A, B, C, D and E. Section E will be
Compulsory, it will consist of a single question with 10-20 subparts of short answer type,
which will cover the entire syllabus and will carry 20% of the total marks of the semester
end examination for the course. Section A, B, C and D will have two questions from the
respective sections of the syllabus and each question will carry 20% of the total marks of
the semester end examination for the course.
2. Candidates are required to attempt five questions in all selecting one question from each
of the section A, B, C and D of the question paper and all the subparts of the questions in
section E. Use of non-programmable calculators are allowed.
Section-A
1. MATRICES
Matrices, Related matrices, Complex matrices (Hermitian and skew-Hermitian matrices,
Unitary matrix), Consistency of linear system of equations, Rank of a matrix, Normal form of a
matrix, Vectors, Linear dependence, Consistency of a linear system of equations, System of
linear homogeneous equations, Linear and orthogonal transformations, Characteristic equation,
Eigen values, Eigen vectors, Properties of Eigen values, Cayley-Hamilton theorem, Quadratic
forms and its reduction to canonical form.
Section-B
2. DIFFERENTIAL CALCULUS
Indeterminate forms, Taylors and Maclaurins series, Partial Differentiation and its
geometrical interpretation, Homogeneous functions, Eulers theorem and its extension, Total
differentials, Composite function, Jacobian, Maxima and minima of functions of two variables,
Method of undetermined multipliers.
Section-C
3. INTEGRAL CALCULUS
Reduction formulas, Quadrature, Rectification, Surface and Volume of revolution for
simple curves, Double integrals and their applications, Change of order of integration, Change of
variables, Triple integrals and their applications, Change of variable, Beta and Gamma functions
and their relationship.
5
Section-D
4. COMPLEX NUMBERS
Applications of De Moivres theorem, Root of a complex number, Exponential, Circular,
Hyperbolic and Logarithmic functions of a complex variable, Inverse Hyperbolic functions, Real
and imaginary parts of Circular and Hyperbolic functions, Summation of the series-C+iS
method.
TEXT BOOKS
1. Advanced Engineering Mathematics: by Erwin Kreyszig, John Wiley and Sons, NC, New
York.
2. Advanced Engineering Mathematics: by R. K. Jain & S. R. K Iyengar, Narosa Pub. House.
REFERENCE BOOKS
1. Advanced Engineering Mathematics: by C. R. Wylie & L. C. Barrett, McGraw Hill
2. Differential & Integral Calculus: by N. Piskunov, MIR Publications.
3. Calculus and Analytic Geometry, by Thomes, G.B, Finney, R.L. Ninth Edition, Peason
Education.
4. Advanced Engineering Mathematics, by Peter. V. O Nil, Wordsworth Publishing
Company.
5. Advanced Engineering Mathematics, by Jain, R.K and Lyengar, S.R.K., Narosa Publishing
Company.
6. Higher Engineering Mathematics, by Grewal, B.S., Khanna Publishers, New Delhi.
7. Engineering Mathematics, by Taneja, H.C., Volume-I & Volume-II, I.K. Publisher.
6
Engineering Physics-I (NS-102)
Course Code NS-102 Credits-4 L-3, T-1, P-0

Name of the Course Engineering Physics-I
Lectures to be Delivered 52 (1 Hr Each) (L=39, T=13 for each semester)
Semester End Max Marks: Min Pass Marks: 40 Maximum Time: 3
Examination 100 hrs
Continuous Assessment (based on sessional test (2) 50%, Max Marks: 50
Tutorials/Assignments 30%, Quiz/Seminar 10%, Attendance 10%)
Instructions
1. For Paper Setters: The question paper will consist of five sections A, B, C, D and E.
Section E will be Compulsory, it will consist of a single question with 10-20 subparts of
short answer type, which will cover the entire syllabus and will carry 20% of the total marks
of the semester end examination for the course. Section A, B, C and D will have two
questions from the respective sections of the syllabus and each question will carry 20% of the
total marks of the semester end examination for the course.
2. For Candidates: Candidates are required to attempt five question in all selecting one
question from each of the section A, B, C and D of the question paper and all the subparts of
the questions in section E. Use of non-programmable calculators is allowed.
Section A
INTERFERENCE-Coherent Sources, Two Beam Interference by Division of Wavefront-
Fresnel Biprism Interference by Division of Amplitude - Newtons Rings, Michelson
Interferometer.
DIFFRACTION-Fraunhoffer Diffraction, Diffraction Through Single Slit, Plane Transmission
Grating, Fresnel Diffraction, Fresnel Half Period Zone, The Zone Plate.
POLARIZATION- Production of Polarized Light, Maluss Law, Double Refraction,
Interference of polarized Light: Quarter Wave Plate And Half Wave Plate.
Section B
Particle Properties of Waves: Electromagnetic Waves, Maxwell Equations, Blackbody
radiations, Photoelectric Effect, Compton Effect, Pair Production,
Waves Properties of Particles: De Broglie waves, Phase velocity, group velocity and Particle
velocity. Relation between phase velocity and group velocity. Relation between group velocity
and particle velocity. Particle Diffraction, Heisenbergs uncertainty principle and its physical
significance (no derivation). Application of uncertainty principle (Non-existence of electron in
the nucleus).
Section C
Quantum Mechanics: Postulates of quantum mechanics, The Wave Euation. Properties and
Physical significance of a wave function. Probability density and Normalisation of wave
function. , Schrodingers equation: Time- Dependent form, Expectation Values,
Operators, Schrodingers equation: Steady- Stateform Eigen values and eigen
function, Application of Schrdinger wave equation Particle in a box, FinitePotential well,
Tunnel Effect, Harmonic oscillator.
7
Section D
Nuclear Structure: Composition of nucleus, Nuclear Properties, Stable Nuclei, binding energy,
Liquid Drop Model, Nuclear Forces.
Nuclear Reactions: Cross-section, Nuclear fission, moderators, nuclear reactors, Nuclear fusion
in Stars, Fusion Reactors
Elementary Particles: Leptons,Hadrons, Elementary particle quantum numbers, Quarks, Field
Bosons,
Cosmology: The Big Bang Theory, Evolution of Stars.
Text Books:
1. A.Ghatak: Optics,Tata Mcgraw Hill, 3rd edition.
2. Arthur Beiser, Concepts of Modern Physics ,6th Edition, Tata Mcgraw Hill-2009
Reference Books:
1. David J Griffith , Introduction to Electrodynamics, Pearson Prentice Hall.
2. Halliday, Resnick and Walker- Principles of Physics, Wiley India 9th Edition-2012
8
ENGINEERING CHEMISTRY (NS 103)
Course Code NS-103 Credits- 04 L-03, T-01, P-0

Name of Course Engineering Chemistry
Continue Assessment (based on sessional tests 50%) Tutorial/ Assignment:
30%, Quiz/ Seminar: 10 %, Attendance: 10 %) MM: 50.
Instructions
1. For Paper Setters: The question paper will consist of five sections A, B, C, D & E. Section
E will be compulsory, it will consist of a single question with 10-20 subparts of short answer
type, which will cover the entire syllabus and will carry 20% of the total marks of the
semester end examination for the course. Section A, B, C & D will have two questions from
the respective sections of the syllabus and each question will carry 20% of the total marks of
2. For candidates: Candidates are required to attempt five questions in all selecting one question
from each of the sections A, B, C & D of the question paper and all the subparts of the
questions in Section E.
SECTION A
Electrochemistry: Electrical Conductance, Types of Electrolyte, Specific Conductance,
Equivalent Conductance, Molar Conductance, Ionic Conductance (Kohlrausch Law), Factors
Affecting Conductance, Transport Number, Interionic Attraction Theory of Conductance,
Hydration of ions, Electrochemical Cell ,Electrode Potential, Standard Electrode Potential,
Galvanic Cells, EMF of the Cell & Free Energy Change, Nernst Equation, Reference Electrodes
(S.H.E,Calomel Electrode, Silver-Silver Electrode, Eletrochemical Series, Glass Electrode,
Concentration Cell, types & applications of Concentration Cell, Batteries(primary cell,
Secondary storage cell, Metal- Air Batteries), Fuel cell, hydrogen-oxygen fuel cell.
Phase Rule: Introduction, One Component System (water system, sulpher system) Two
components System (lead-silver & Zinc- magnesium system), thermal Analysis.
SECTION B
Water Treatment: Introduction, Sources of water, Impurities, Hardness Analysis, Oxidations,
(BOD & COD), Boiler Corrosion Sewage & Treatment.
Corrosion and its Controls: Introduction, Types of corrosions, Electrochemical Theory, Pitting,
Water Line, Differential Aerations corrosions, Stress Corrosions, Factors affecting Corrosions,
Preventive measures.
SECTION C
Instrumental Methods of Analysis
Introduction to spectroscopy; UV-Visible spectroscopy- Absorption laws ,Instrumentation,
formation of absorption bands, Theory of electronic spectroscopy, Chromophore and
auxochrome concept, fluorescence & phosphorescence, application of UV-Visible spectroscopy ;
9
IR spectroscopy- Principle, theory of molecular vibrations, important features of IR spectroscopy
and applications; NMR-Principle, relaxation processes, Instrumentation, Shielding-desheilding
effects, spin coupling, coupling constant, applications of NMR.
Fuel and Combustion: Introduction, class of fuels ( Solid, Liquid and Gases) Coal and its
origin, Analysis of Coals, Petroleum fuels, Cracking, Reforming, Octane no, Cetane no,
Gaseseous fuel Water gas, producer gas, bio gas, coal gas and oil gases
SECTION D
Polymers Classification of polymers, types of polymerizations, plastics, some important
commercial thermoplastics (polythene, polypropylene, polystyrene, polyvinylchloride, Teflon,
plexiglass, polyurethanes), thermosetting (Bakelite, epoxy resin, Urea formaldehyde)
Elastomers- synthetic rubbers, synthetic fibers.
Composite Materials
Introduction, Classification, Constituents of composites, Fiber reinforced composites,
unidirectional fibre reinforced composites, short fibre reinforced composites, particle reinforced
composites, important types of particulate composites, Failures of fiber reinforced composites,
Advantages and applications of composites.
TEXT BOOKS:
1. Engineering Chemistry by Dr Ramesh Thakur and Dr.Subba Ramesh, Wiley India
publisher
2. A Text Book of Engineering Chemistry by ShashiChawla, DhanpatRai& Sons.
REFERENCE BOOKS:
1. Engineering Chemistry by P C Jain & Monika Jain
2. Fundamental of organic spectroscopy by Y. R. Sharma
3. Spectroscopic methods by Williams and Fleming
10
Communication & Professional Skills in English (HS-102)
Course Code HS-102 Credits-3 L-3, T-1, P-0

Name of the Course Communication & Professional Skills in English
Semester End Examination Max Marks: 100 Min Pass Marks: 40 Maximum Time: 3 hrs
Continuous Assessment (based on Sessional test (2) 50%, Max Marks: 50
Instructions
1. For Paper Setters: The question paper will consist of five sections A, B, C, D and E.
Section E will be Compulsory, it will consist of a single question with 10-20 subparts of
short answer type, which will cover the entire syllabus and will carry 20% of the total
marks of the semester end examination for the course. Section A, B, C and D will have two
questions from the respective sections of the syllabus and each question will carry 20% of
the total marks of the semester end examination for the course.
2. For Candidates: Candidates are required to attempt five question in all selecting one
question from each of the section A, B, C and D of the question paper and all the subparts
of the questions in section E.
Section A
Essentials of communication:
The process of communication: communication competence, types and channels of communication
verbal and non-verbal, Importance of listening skills in communication: types of listening,
barriers to listening, Barriers to communication and removal of these barriers, personal SWOT
Analysis, Analyzing audience, role of emotions and body language in communication.
Section B
Written communication:
Enriching vocabulary, using vocabulary in different context, Essentials of strong writing skills,
language and style of writing, characteristics of a good technical style, logical reasoning,
Paragraph writing, Developing perspective: goals, objectives and principles of critical thinking.
Section C
Reading Comprehension:
Importance of reading: Eye movement, fixations, regression, visual wandering, right approach to
reading, SQ3R method of reading, Precis writing, Comprehension, Essay writing.
Section D
Technical Communication:
Report writing: Importance, structure, drafting of reports, Business Writing: Sales letters, claim
and adjustment letters, inviting/sending quotations, Tenders, Memorandum, Job Application letter,
Preparing a personal resume, notices, agenda and minutes of meeting.
11
TEXT BOOKS:
1. An Introduction to Professional English and Soft Skills: by Bikram K. Das, Kalyani
Samantray, Cambridge Press.
2. Business correspondence and Report Writing: by R. C. Sharma & Krishna Mohan
REFERENCE BOOKS:
1. Communication Skills, Sanjay Kumar and PushpLata, Oxford University Press.
2. Chrissie Wright (Ed.); Handbook of Practical Communication Skills; JAICO Books
3. Effective Communication and soft Skills, NitinBhatnagar and MamtaBhatnagar, Pearson
Publication.
4. Communicative English for Engineers and professionals, NitinBhatnagar and
MamtaBhatnagar, Pearson Publication.
5. Communication Skills and soft skills- An integrated approach, Kumar, Pearson
Publication
6. Communication Skills for Engineers, Mishra, Pearson Publication
7. K.K.Sinha, Business Communication, Galgotia Publishing Company, New Delhi, 1999.
8. R.K.Bansal& J.B. Harrison, spoken English for India, Orient Longman.
Recommended Readings:
1. Business @ The Speed of thought, Bill Gates.

2. My Experiments with Truth, M.K.Ghandhi
3. Wings of Fire, A.P.J. Kalam
4. An Autobiography, JwaharLal Nehru.
12
BASIC MECHANICAL ENGINEERING (BE-102)
Course Code BE-102 L-3, T-1, P-0

Name of the Course Basic Mechanical Engineering
Lectures to be delivered 52 (1 Hr Each) (L = 39, T = 13 for each semester)
Semester End Examination Max. Time = 3 hrs. Max. Marks: 100 Min. Pass Marks: 40
Continuous Assessment (based on sessional tests (2) 50%, Max. Marks: 50
the respective sections of the syllabus, and each question will carry 20% of the total marks of
Note: The paper setter will be required to mention a note in the question paper that use of
steam table, graphical plots are permitted.
2. For candidates: Candidates are required to attempt five questions in all selecting one
question from each of the sections A, B, C & D of the question paper and all the subparts of
the questions in Section E. Use of non-programmable calculators is allowed.
Section-A
Basic concept: Dimensions and units, thermodynamic systems, thermodynamic properties and
process, thermodynamic equilibrium, energy-kinetic, potential and internal, heat and work,
zeroth law, concept of temperature, definition of ideal gas, laws and properties of ideal gas.
First law of Thermodynamics: First law for control mass (closed system), internal energy as a
property, enthalpy, specific heats, non-flow processes of ideal gases, cyclic process, first law for
control volume (open system), applications of steady flow energy equation to engineering
devices.
Section-B
Second law of Thermodynamics: Limitations of first law of thermodynamics, Kelvin- Planck
and Clausius statements, their equivalence, application of statements of second law to heat
engine, heat pump and refrigerator, reversible processes, reversible cycles, and carnot cycle,
corollaries of the second law, thermodynamics temperature scale, Clausius inequality, entropy,
principle of increase of entropy, availability and irreversibility.
Properties of Steam: Phase transformation, phase diagram, condition of steam- saturated steam,
dry-saturated steam, wet steam, superheated steam, dryness fraction, property of steam, steam
tables, use of Mollier charts , process of vapors and various process.
Section-C
Gas Power Cycles: Carnot, Diesel, Otto, Dual combustion, working of 2-stroke and 4-stroke
engine, Air standard thermal efficiency, Concepts of mean effective pressure, indicated power
and brake powerfor reciprocating engines.
13
Section-D
Introduction of Psychometry: The Gibbs Dalton law, Psychometric terms, Introduction of
Psychometry Chart.
Introduction to Heat Transfer: Mechanisms Conduction, Convection and Radiation,
Introduction to Fouriers Law of heat conduction, Newtons law of cooling, Stefan-Boltzmann
law.
Introduction to Fluid Mechanics: Fluid, properties of fluid, viscosity, Newtons law of
viscosity, surface tension, types of fluid, buoyancy.
TEXT BOOKS:
1. Basic Mechanical Engineering by Basant Aggarwal and CM Aggarwal Wiley India.
2. Fundamentals of Mechanical Sciences: Engineering Thermodynamics and Fluid
Mechanics by Mukherjee and Paul, PHI Learning.
REFERENCE BOOKS:
1. Thermodynamics An Engineering Approach (SI Units) Yunus. A. Cengel, Michael A.
Boles, TMH New Delhi
2. Fundamentals of Thermodynamics Sonntag, Borgnakke Van Wylen Wiley India.
3. Engineering Thermodynamics by P.K. Nag, TMH, New Delhi
4. Thermodynamics by C.P. Arora, TMH, New Delhi
5. Fundamentals of Mechanical Engineering, 2nd Edition by G.S. Sawhney, PHI Learning
Private Limited.
14
Principle of Computer Programming & C++ (BE-104)
Course Code BE-104 Credits-4 L-3, T-1, P-0

Name of the Course Principle of Computer Programming & C++
Lectures to be Delivered 52 (1 Hr Each) (L=39, T=13 for each semester)
Continuous Assessment (based on sessional tests (2) 50%, Max Marks: 50
SECTION-A
Introduction to Computer:-Definition, Characteristics..Generation of Computers, Capabilities
and Limitations.Introduction to Operating System.Basic Components of a Computer System-
Control Unit, ALU, Input/output functions and characteristics. Memory Introduction,
Classifications- Volatile Memory and Non- Volatile , Memory, ROM, RAM.
Input, Output and storage Units:-Computer Keyboard, Pointing Devices: Mouse, Trackball,
Touch Panel, and Joystick, Light Pen, Scanners, Various types of Monitors.
Hard Copy Devices:- Impact and Non- Impact Printers- Daisy Wheel, Dot Matrix, Line Printer,
Chain Printer. Non Impact Printers- DeskJet, Laser Printer, Virus : General introduction of virus
and anti-virus .
SECTION-B
High Level Language and Low Level Language, Software and its different types- System
Software, Application software.Compiler, Interpreter and Assembler. Introduction to algorithm
and Flow chart: - Representation of an algorithm, flowchart symbols and flow chart, rules,
advantage and limitations of flowchart and pseudo code. Testing and Debugging:-Definition of
testing and debugging , types of program errors.
DOS : Internal and External Commands , Difference between External and Internal Commands.
SECTION-C
Introduction to C++ :Starting with C++, Features of C++ Procedure-oriented programming
OOP vs. procedure-oriented programming Compiling, linking and running a C++ program.
Object-Oriented Programming Concepts: Abstraction , Inheritance, Polymorphism, Data
Binding , Encapsulation., Classes and Objects Concept of a class ,Defining a class, Creating an
object , Object Scope.
The Basics of C++ :Basic Data Types, User-defined Data Types, Variable Declarations,
Variable Names Constants and its types , Character Constants , String Constants, Standard input
and standard output Formatted input cin and Formatted output cout.
Working with Operators and Expressions: Operators, Arithmetic Operators, Relational
Operators, Assignment Operator, Logical Operators, Increment and Decrement Operators (++
and --), 'Operate-Assign' Operators (+=, =, ...).
15
SECTION-D
Controlling the Program Flow: Decision control : if, if else, if - else if . Loop Control :
while, do while, for, break,continue Case Control switch, goto.
Functions/Procedures: function,Returning values from functions,Arguments Passed by
ValuePassing Addresses of Arguments,Concept of variable scope and scope rules,Global
variables
Pointers and Arrays: Pointers,Pointer Initialization,Pointer Operators ,The & (and) Operator
Understanding Arrays, Initializing Arrays.
Files: reading, writing text and binary files, pointers, character pointers, pointers to arrays, arrays
ofpointer to structures.
TEXT BOOKS:
1. Fundamentals of Computers by Rajaraman, V., PHI Publication
2. Object oriented programming in C++ by Rajesh K. Shukla, Wiley India.
REFERENCE BOOKS
1. The C++ programming language ,Bjarne Stroustrup ,Addison Wesley , 2000.

2. Basic Computer Engineering, Kogent learning solution Inc. Dreamtech Press.
3. Object oriented programming Principles and Fundamental, Gim Keogh and Mario
Giannini, John Wiley.
4. Object oriented programming in turbo C++, Robbet Lofre, 4 Ed Pearson Publication.
5. Programming with C++, D. Ravichandern, Tata Mcgraw Hill 1996.
6. Object oriented programming in C++, Nicolai M Josuetis, John Wiley.
16
Engineering Chemistry Lab (NS-103(P))
Course Code NS-103(P) Credits-2 L-0, T-0, P-2

Name of the Course Engineering Chemistry Lab
Lectures to be Delivered 26 hours of Lab. work (2 hrs. per week)
Continuous Assessment Lab work 30% Lab Record 25% Max Marks: 25
Viva/ Hands on 25% Attendance 20%
Instructions for paper setter / candidates

Laboratory examination will consist of two parts:
Performing a practical exercises assigned by the examiner.
Viva-voce examination
Viva-voce examination will be related to the practicals performed / project executed by the
candidate related to the paper during the course of the semester.
NOTE: At least 10 to 12 experiments to be performed.

List of Experiments
1. To determine the surface tension of the given liquid by drop number method by using
stalgmometer and identify the given liquid.
2. To determine the insoluble, soluble and total solids in given sample of sewage.
3. To determine the solid carbon, volatile matter, ash content and percentage of moisture in given
sample of coal by proximate analysis method and classify the coal.
4. To determine the total alkalinity in a given sample of water using a standard acid.
5. To determine the percentage of Chlorine in a given sample of CaOCl2 which has been
dissolved in one litre of solution..
6. To determine the surface tension of the two given unknown liquids by using Stalgmometer and
identify the given liquid.
7. To determine the coefficient of viscosity of the given unknown liquids by using Ostwalds
Viscometer and identify the given liquid.
8. To determine the coefficient of viscosity of the given lubricating oil using Red Wood
Viscometer
9. To determine the coefficient of viscosity of the given lubricating oil using Seybolt Viscometer.
10. To determine the flash point and fire point of given sample of oil using Pens key Martens
apparatus.
11. To determine the amount of Chlorine in given sample of water approximate N/20 sodium
Thiosulphate solution.
12. To determine the maximum wavelength of solution of cobalt chloride
13. To determine the Beers Law and apply it to find the concentration of given unknown
solution by spectra-photometer.
14. To determine the chemical oxygen demand of waste water.
15. To determine the half-life period of given radioactive sample using GM counter.
17
Communication & Professional Skills Lab-I (HS-102(P))
Course Code HS-102 (P) Credits-2 L-0, T-0, P-2

Continuous Assessment Lab work 30% Lab Record 25% Max Marks: 25
Instructions for paper setter / candidates:

(i) Performing a practical exercises assigned by the examiner .
(ii) Viva-voce examination
Note: Each practical should be performed twice for effectiveness.
List of Practicals:
1. Word processing a document.

2. Power point presentations.
3. Resume / Biodata preparation
4. Report writing.
5. Preparing notice, agenda and minutes of meeting.
6. Preparation of Quotation and tender document
7. Note making based reading comprehension
8. Prcis Writing
Recommended books:
1. English Conversation Practice by Grant Taylor
2. Business correspondence and Report Writing: by R. C. Sharma & Krishna Mohan
3. Chrissie Wright (Ed.); Handbook of Practical Communication Skills; JAICO Books.
4. Veena Kumar, The Sounds of English, Makaav Educational Software, New Delhi.
18
Computer Programming Laboratory (BE-104(P))
Course Code BE-104 (P) L-0, T-0, P-2

Name of the Course Computer Programming Laboratory
Lectures to be Delivered 26 Hrs. of Lab work (2hrs. each per week)
Continuous Assessment Lab work 30% Lab Record 25%, Max Marks: 25
Viva 25% Attendance 20%

NOTE: At least 10 to 12 experiments to be performed.

List of Experiments
1. Write a Program to find the sum, difference, product and quotient of two integers.
2. Write a program C++ Program to output an integer, a floating point number and a
character.
3. Write a program to switch between different cases.
4. Write a program to count the number of words and characters in a sentence.
5. Program to find the roots of a quadratic equation.
6.
Create a class rational which represent a numerical value by two double values
numerator and Denominator include the following public members functions
Constructor with no argument(default)
Constructor with two arguments
Void reduce ()that reduce the rational number by eliminating the highest common factor
between the numerator and the denominator
Overload + operator to add two rational numbers
Overload >> operator to enable input through cin.
Overload << operator to enable input through cout.
7. Write a program to convert days into years and weeks.

8. Write a program to convert temperatures from Celsius to Fahrenheit and vice versa.
9. Write a program to find the sum of either of the diagonals of a 4 x 4 matrix.
10. Write a program to enter a sentence and output the number of uppercase & lowercase
consonants, uppercase & lowercase vowels in sentence.
11. Write a program to enter 10 integers in a single-dimension array and then print out the
array in ascending order.
12. Write a program to find the sum of each row & column of a matrix of size n x m and
if matrix is square, find the sum of the diagonals also.
13. Write a program to display fibonacci series upto n terms.
19
14. Write a program for payroll system using inheritance.
15. To calculate the total mark of a student using the concept of virtual base class.
16. Program for Write File Operation Using C++ Programming.
17. Write a program that creates a binary file by reading the data for the student for the
terminal .The data of each student consist of roll number, name (a string of thirty or lesser
number of characters ) and marks.
18. Write a program to read a number and display its square, square root, cube and cube root.
Use a virtual function to display any one of the above.
19. Write a program to read two matrix and find their product use operator overloading so
that the statement for multiplying the matrix may be written as Z=x*y where x,y,z are
matrices.
20
WORKSHOP PRACTICE-I (WS-101)
Course Code WS 101 L-0, T-0, P-3

Name of the Course Workshop Practice I
Lectures to be delivered 39 hours of Lab sessions in each semester
Semester End Examination Max. Marks: 25 Min. Pass Marks: 10
Continuous Lab work 30%, Lab record 25%, Max. Marks: 25
Assessment Viva 25%, Attendance 20%
INSTRUCTIONS:

List of Experiments: -
Fitting Shop: -
Introduction to the tools used in Fitting Shop and various processes in Fitting shop.
1. To make a square piece of mild steel.
2. To make V-matching joint of mild steel.
3. To make a V-notch.
Machine Shop: -
Introduction to various machine tools and machine parts, such as Lathes, drilling machine,
grinders etc. Cutting tools and operations.
1. Facing and turning on mild steel rod on Lathe Machine.
2. To make a groove on lathe machine.
3. Taper turning operation on Lathe Machine.
Carpentry and Pattern making Shop: -

Carpentry and Pattern Making Various types of timber and practice boards, defects in timber,
seasoning of wood, tools, operations and joints. Introduction to the tools used in carpentry shop.
1. To make the T lap joint.
2. To make T Dove-tail joint.
3. To make Mortise &Tennon joint.
Welding Shop: -
Introduction to different welding methods, welding equipment, electrodes, welding joints,
awareness of welding defects.
1. To make a lap joint.

2. To make a T joint.
3. To make a V-butt joint.
21
Smithy and Forging: -
Introduction to forging tools, equipments, and operations, Forgability of metals.
1. To make a ring of mild steel by cold forging process.
2. To make S-hook by hot forging process.
3. To make chisel by hot forging process.
Foundry Shop: -
Introduction to moulding materials, moulds, use of cores, melting furnaces, tools and equipment
used in Foundry.
1. Make a single piece pattern mould.
2. To make spilt pattern mould.
3. To make mould and core and assemble it.
Electrical and Electronics Shop: -

Demonstration of tools, Introduction to electric wiring, Exercises preparation of PCBs, involving
soldering of electrical & electronic application.
1. Fault rectification, disassembly and assembly of (any two) electrical appliances viz. electric
iron, electric mixer, ceiling and table fan, tube light, blower and water heater.
2. Demonstration and use of flowing electronic instruments: multimeter, voltmeter, ammeter,
energy meter, CRO.
Suggested Reading: -
1. Workshop Technology by Chapman.

2. Manufacturing Processes by Begman.
3. Manufacturing Materials and processes by JS Campbell.
4. Mechanical Workshop Practice, 2nd Edition by John, PHI Learning Private Limited.
22
Semester II
Engineering Mathematics-II (NS-104)
Course Code NS-104 L - 3, T- 1, P - 0

Name of Course Engineering mathematics-II
Continue Assessment (based on sessional tests 50%) Tutorial/ Assignment: MM: 50.
30%, Quiz/ Seminar: 10 %, Attendance: 10 %.
Instructions
1. The question paper will consist of five sections A, B, C, D and E. Section E will be
Compulsory, it will consist of a single question with 10-20 subparts of short answer type,
which will cover the entire syllabus and will carry 20% of the total marks of the semester
end examination for the course. Section A, B, C and D will have two questions from the
respective sections of the syllabus and each question will carry 20% of the total marks of
2. Candidates are required to attempt five questions in all selecting one question from each
of the section A, B, C and D of the question paper and all the subparts of the questions in
section E. Use of non-programmable calculators are allowed.
Section-A
INFINITE SERIES: Convergence and divergence of infinite series, Geometric series test,
Positive term series, p-series test, [Comparison test, DAlemberts ratio test, Cauchys root test
(Radical test), Integral test, Raabes test, Logarithmic test, Gausss test] (without proofs),
Alternating series and Leibnitzs rule, Power series, Radius and interval of convergence, absolute
convergence and Conditional convergence.
Section-B
FOURIER SERIES: Eulers formula, Conditions for a Fourier expansion, Dirichlets
conditions, Functions having points of discontinuity, Change of interval, Odd and even periodic
functions, Expansion of odd and even periodic functions, Half-range series, Typical wave-forms,
Parsevals formula.
Section-C
LINEAR DIFFERENTIAL EQUATIONS: Brief review of first order ordinary differential
equations, Exact equations, Equations reducible to exact equations, Equations of the first order
and higher degree, Clairauts equation, Linear differential equations with constant co-efficients,
Complimentary functions and particular integral, Method of variation of parameters, Equations
reducible to linear equations with constant co-efficients (Cauchys and Legendres linear
equations).
Section-D
VECTOR CALCULUS: Curves in space, curvature and torsion, Scalar and vector point
functions, Differentiation of vectors, Vector operator Del, gradient, divergence and curl with
their physical interpretations, Formulae involving gradient, divergence and curl, Line, surface
23
and volume integrals, Greens Theorems, Stokes and GaussTheorems and their verifications and
applications. Scalar potential, solenoidal and irrotational fields.
TEXT BOOKS
1. Advanced Engineering Mathematics by ErwinKreyszig, John Wiley and Sons, N.C., New
York.
2. Advanced Engineering Mathematics by R. K. Jain & S. R. K Iyengar, Narosa Publishing
House.
REFERENCE BOOKS
1. Advanced Engineering Mathematics: by C. R. Wylie & L. C. Barrett, McGraw Hill
2. Higher Engineering Mathematics byB S Grewal,Khanna Publishers, New Delhi.
4. Calculus and Analytic Geometry by Thomes, G.B, Finney, R.L. Ninth Edition, Pearson
Education.
5. Advanced Engineering Mathematics byPeter. V. ONil, Wordsworth Publishing
Company.
6. Vector Calculus by C. E. Weatherburn. John Wiley and Sons, NC, New York.
7. Differential Equations by Shepley L. Ross, John Wiley & Sons, New York.
24
Engineering Physics II(NS 105)
Course Code NS-105 L-3, T-1, P-0

Name of the Course Engineering Physics II
Lectures to be delivered 52 (1Hr.each) (L = 39, T = 13 for each semester)
Semester End Examination Max. Time: 3 hrs. Max. Marks: 100 Min. Pass Marks: 40
Continuous Assessment (based on sessional tests 50%, Max. Marks: 50
Instructions
1. For Paper Setters: The question paper will consist of five sections A, B, C, D & E.
Section E will be compulsory, it will consist of a single question with 10-20 subparts of
short answer type, which will cover the entire syllabus and will carry 20% of the total
marks of the semester end examination for the course. Section A, B, C & D will have two
questions from the respective sections of the syllabus and each question will carry 20%
of the total marks of the semester end examination for the course.
question from each of the sections A, B, C & D of the question paper and all the subparts
of the questions in Section E. Use of non-programmable calculators is allowed.
SECTION A
Crystal Structure: Space lattice, Bravais lattice - unit cell, primitive cell. Lattice
parameters. Crystal systems. Direction and planes in a crystal.Miller indices. Expression for
inter-planar spacing.Co-ordination number. Atomic packing factor. Braggs Law.Determination
of crystal structure by Braggs x-ray spectrometer. Crystal structures of NaCl, and diamond.
Free electron theory: Elements of classical free electron theory and its limitations. Quantum
theory of free electrons, Fermi level, density of states, fermidirac distribution function,
Thermionic emission, Richardsons equation.
(10 Lectures) & (Text Book-1)
SECTION B
Band Theory of Solids: Origin of energy bands, Periodic Potential in a crystal, Wave function
in a periodic potential, kronig, Penney Model (qualitative), E-K diagrams, Brillouin Zones,
Effective mass of electron, Concept of negative effective mass and holes, Classification into
metals, semiconductors and insulators, fermi energy and its variation with temperature.
SECTION C
Dielectric and Magnetic Properties of Materials: Dielectric polarization, dielectric constant,
types of polarization, electric field, electric displacement and dielectric polarization vector &
relation between them, Gauss;s law in the presence of dielectric, Behavior of dielectric in
alternating field- simple concepts, Atomic Magnetic Moments, Classification of magnetic
materials, Dia, para, and ferromagnetic materials, domains, B-H graph in ferromagnetic
materials Anti-ferromagnetism &ferrimagnetisms, . Soft and Hard magnetic materials. Ferrite
and their applications.
25
Superconductivity: Temperature dependence of resistivity in superconducting
materials. Effect of magnetic field (Meissner effect). Type I and Type II superconductors. BCS
theory (qualitative), High temperature superconductors, Applications of superconductivity.
SECTION D
Lasers: Spontaneous and stimulated emission, Einsteins Coefficients, Characteristics of Laser
beam, Population inversion, Pumping Techniques, Components of a laser system, Ruby Laser
and He-Ne Lasers
Fiber Optics: Basics of fiber optics, Total Internal Reflection, Acceptance angle, Numerical
aperture, Single mode & Multimode fibres, Step index and Graded index fiber, pulse Dispersion
in optical fibres, Attenuation in Optical Fibres, applications of optical fibres.
Text Books:
1. Rajnikant: Applied Solid State Physics, Wiley India Pvt Ltd.
2. A. Ghatak: Optics,Tata Mcgraw Hill, 3rd edition.
Reference Books:
1. Charles Kittel: Introduction to Solid State Physics, John Wiley & sons Inc.
2. S. O. Kasap, Principle of Electronic materials and Devices.
26
DISASTER MANAGEMENT AND ENVIRONMENTAL SCIENCE (HS-101)
Course Code Hs-101 L-3, T-1, P-0

Name of the Course Disaster Management and Environmental Science
Lectures to be delivered 52 (1 Hr Each) (L = 39, P = 13 for each semester)
INSTRUCTIONS:
Section-A
Principles of Disaster Management. Natural Disasters such as Earthquake, Floods, Fire,
Landslides, Tornado, Cyclones, Tsunamis, Nuclear, Chemical, Terrorism, Extra Terrestrial and
other natural calamities. Hazards, Risks and Vulnerabilities. Assessment of Disaster
Vulnerability of a location and vulnerable groups, National policy on disaster Management,
Section-B
Prevention, Preparedness and Mitigation measures for various Disasters, Post Disaster Relief &
Logistics Management, Emergency Support Functions and their coordination mechanism,
Resource & Material Management, Management of Relief Camp, Information systems &
decision making tools, Voluntary Agencies & Community Participation at various stages of
disaster, management, Integration of Rural Development Programmes with disaster reduction
and mitigation activities.
Section-C
Renewable and non-renewable resources, Role of individual in conservation of natural resources
for sustainable life styles. Use and over exploitation of Forest resources, Deforestation, Timber
extraction, Mining, Dams and their effects on forest and tribal people. Use and over exploitation
of surface and ground water resources, Floods, Drought, Conflicts over water, Dams- benefits
and problems. Causes, effects and control measures of Air pollution, Water pollution, soil
pollution, Noise pollution, Thermal pollution, Nuclear hazards.
27
Section-D
Global Environmental crisis, Current global environment issues, Global Warming, Greenhouse
Effect, role of Carbon Dioxide and Methane, Ozone Problem, CFCs and Alternatives, Causes of
Climate Change Energy Use: past, present and future, Role of Engineers.
TEXT BOOKS:
1. Disaster Management By G. K. Ghosh A.P.H. Publishing Corporation
2. Environmental Studies, R Rajgopalan, Oxford University Press
REFERENCE BOOKS:
1. Modern Encyclopaedia of Disaster and Hazard Management By B C Bose Rajat publications.
2. Disaster Management By R.B. Singh Rawat Publications.
3. Disaster Management By B Narayan A.P.H. Publishing Corporation.
4. Environmental Studies, Daniels, Wiley Publication
5. Environmental Studies, Basak, Pearson Publication
28
Basic Electrical & Electronics Engineering (BE-101)

Name of the Course Basic Electrical & Electronics Engineering
Lectures to be delivered 52 (1 Hr Each) (L = 39, T = 13 for each semester)
Semester End Examination Max. Time: 3 hrs. Max. Marks: 100 Min. Pass Marks:40
Instructions
1. For Paper Setters: The question paper will consist of five sections A, B, C, D & E. Section E
will be compulsory, it will consist of a single question with 10-20 subparts of short answer type,
which willcover the entire syllabus and will carry 20% of the total marks of the semester end
examination for the course. Section A, B, C & D will have two questions from the respective
sections of the syllabus andeach question will carry 20% of the total marks of the semester end
examination for the course.
from each of the sections A, B, C & D of the question paper and all the subparts of the questions
in Section E. Use of non-programmable calculators is allowed.
SECTION A
DC circuits:. Ohms law , resistance, receptivity, series & parallel connections, star delta
transformation, power dissipation in resistance, effect of temperature on resistance. Kirchhoffs
laws Mesh laws; Mesh & Nodal analysis.
AC circuits: Generation of alternating voltage &currents, Sinusoidal signals, instantaneous and
peak values, R.M.S. &Average value, phase angle, polar and rectangular, exponential and
trigonometric representations of RL and C components,
Electrical Instruments and Devices: Voltmeter, Ammeter, Wattmeter, Energy meter, Inverters.
Introduction to Domestic Electric Wiring
SECTION B
Series and Parallel Circuits: A.C.Through resistance; inductance & capacitance. R-L; R-C &
R-L-C series & parallel circuits, phasor diagrams. Power & power factor, series & parallel
resonance. Problems by analytical as well as physical methods.
Three phase circuits: Three phase voltage & current generation, star & delta connections
(balanced load), relationship between phase &line currents and voltages, phasor diagrams,
measurement of power by two wattmeter methods.
A.C. And D.C. Machines: Principle, construction and working of transformer. Introduction to
D.C and A.C. machines.
SECTION C
Semiconductor Devices & Circuit: Classification of material; Energy band structure of
conductors, insulators & semiconductor ;Classification of Semiconductor Mobility and
conductivity, Intrinsic and extrinsic semiconductors and charge densities in semiconductors,
current components insemiconductors, continuity equation. ; PN junction Characteristics&
29
Analysis ;diode rating ; Types of diodes Zener diodes, Photodiodes, Light emitting diodes
(LEDs), Varactor diodes and tunnel diodes. Rectifiers and filter circuit: Half wave, full wave
and Bridge rectifier circuits and their analysis, L, C and Pi filters, Basic regulator supply using
zener diode.
Transistors: Construction and characteristics of bipolar junction, transistors (BJTs)-Comm.
Base, Comm. emitter, Comm. Collector configuration.
SECTION D
Field Effect Transistor: Construction and characteristics of JFET.MOSFET construction and
characteristics.
Integrated Circuits: Classification Of ICs; Monolithic ICs; OP Amp: Characterstics of Ideal
OPAmp& application
Electronic Instruments: Role and importance of general purpose test Instruments, Electronic
Millimeter, Cathode Ray Oscilloscope, Measurement of amplitude, Frequency and phase using
CRO.
TEXT BOOKS:
1. Basic Electrical & Electronics Engineering V Jegathesan, K Vinoth Kumar &
R Saravanakumar, Wiley India
2. Basic Electrical & Electronics Engineering- B.L.Thereja
3. Fundamentals of Electrical & Electronics Engg. 2nd Edition by Smarajit Ghosh, PHI
Learning Private Limited.
REFERENCE BOOKS:
1. Electronics devices and circuit theory by Robert Boylestad.
2. Electronics Devices and circuits by Millman&Halkias, TMH.
3. Basic Electronics by Debashis De, Pearson Education, 2010.
4. Electronics devices and circuit by Bhargava and Kulshtreshta, TTTI Series
30
ENGINEERING MECHANICS (BE-105)
Course Code BE 105 L-3, T-1, P-0

Name of the Course Engineering Mechanics
Lectures to be delivered 52 (1 Hr Each) (L = 39, T = 13, P=0 for each semester)
INSTRUCTIONS:
the respective sections of the syllabus, and each question will carry 20% of the total marks of
Section-A
Force, Moment, Center of gravity & Moment of Inertia: Idealization of Mechanics, Concept
of Rigid Body and Elastic Body, Laws of Mechanics, Forces & System of Forces, Composition,
Resolution & resultant of Forces, Laws of Forces, Lamis Theorem, Moment & Couples,
Varignons Theorem, Free Body Diagram, Centre of Gravity of a Lamina, Centroids of various
Geometric Shapes, Moment of Inertia, Radius of Gyration, Parallel and Perpendicular Axis
Theorem.
Frames and Trusses: Introduction, Perfect Frame, Redundant Frame, Reactions of Supports,
Plane Trusses, Space Trusses, Method of Joints, Method of Section, Graphical Method- Maxwell
Diagram.
Section-B
Simple Stresses and Strains: Stress & strain; Types of stresses and strains Elastic limit; Hooks
law; Stress strain diagram for ductile and brittle material, Factor of safety; Poissons ratio;
Elastic constants; Youngs modulus, Shear modulus & Bulk modulus. Relationship between
elastic constants. Thermal Stress & Strain.
Shear Force and Bending Moment: Concept of beams - statically determinate and
indeterminate beams, Concept and definition of shear force and bending moment, Sign
conventions, Types of load concentrated, uniformly distributed, uniformly varying, Types of
beams: Cantilever beam, simply supported beam, overhanging beam; Shear force and bending
moment diagrams for the above beams subjected to different loadings and couples. Point of
contra flexure, Relationship between load, Shear force and bending moment.
31
Section-C
Bending Stresses in Beams: Bending Stresses in Beams with derivation of Bending equation
and its application to beams of circular, rectangular I & T Section, Composite beams.
Shearing Stresses in Beams: Shearing stress at a section in a loaded beam, Shear stress
distribution over different sections.
Section-D
Torsion of Circular Shaft: Introduction, Theory of Pure torsion - Derivation of torsion
equation, assumptions made in theory of pure torsion, Maximum torque transmitted by Solid and
hollow shafts, Polar modulus, Torsion rigidity, Power transmitted by a shaft, Comparison of
hollow and solid shaft subjected to pure torsion,Close coiled helical spring subjected to axial
load and torque.
Introduction to Friction: Definition, Principles of friction, Friction between solid bodies,
Coefficient of friction, Kinetic friction force, Definition & Determination of angle of friction,
Laws of friction , Procedure for friction analysis, Equilibrium of rigid bodies subjected to
frictional force of resistance, Friction at the ends of ladder, Wedge friction, Remedial measures
in overcoming friction.
TEXT BOOKS:
1. Engineering Mechanics-Nelson, McGraw Hill
2. Engineering Mechanics: Statics, Meriam, JohnWiley
REFERENCE BOOKS:
1. Mechanics of Materials-E.J. Hearn, Elsevier
2. Engineering Mechanics-Bhavikatti, New Age International
3. Engineering Mechanics- JagatBabu, Pearson
4. Engineering Mechanics, P.N. Chandramouli, PHI Learning Private Limited.
5. Engineering Mechanics, V. Jayakumar & M. Kumar, PHI Learning Private Limited.
32
ENGINEERING DRAWING AND GRAPHICS (BE-103)

Name of the Course Engineering Drawing and Graphics
INSTRUCTIONS:
1. For Institutes: There will be two sessions per week. 1st session will consist of one lecture
and two hours of practice session. 2nd session will consist of three hours of practice session.
Section-A
Drawing Techniques and Scales: Various type of lines, principal of dimensioning, size and
location as per IS code of practice (SP-46) for general Engg. Drawing. Practice of drawing,
various types of lines and dimensioning exercises. Drawing exercises pertaining to
symbols.Conventions and Exercise of lettering techniques.Free hand printing of letters and
numerals in 3, 5, 8 and 12 mm sizes, vertical and inclined at 75 degree.Instrumental lettering in
single stroke.Linear scale, Diagonal scale &vernier scale.
Points, Lines and Planes: Projection of Points, Lines and Planes: Concept of horizontal and
vertical planes. First and third angle projections: projections of point and lines, true length of
lines and their horizontal and vertical traces, projection of planes and their traces. Auxiliary
planes.
Section-B
Projections of Solids: Right regular solids of revolution and polyhedrons etc. and their auxiliary
views.
Sectioning of Solids: Principal of sanctioning, types of sanctioning and their practice on
projection of solids, sectioning by auxiliary planes.
Section-C
Development of Surfaces: Development of surfaces of cylinders, cones, pyramid, prism etc.
exercises involving development of unique surfaces like Y-piece, hopper, tray, truncated pieces
etc.
33
Intersection of Surfaces: Intersection of cylinders, cones and prisms with their axes being
vertical, horizontal or inclines. Exercise on intersection of solids-cylinder and cylinder, cylinder
and cone, prism and prism.
Section-D
Isometric Projection: Concept of isometric views: isometric scale and exercise on isometric
views. Practice of Orthographic projections.
Simple Trusses: Graphical Method.
TEXT BOOKS:
1. Engineering Drawing & Engg. Graphics byP. S. Gill, Kataria and Sons Millennium
Edition.
2. Engineering Drawing Plane and Solid Geometry byN.D. Bhatt and V. M. Panchal, 44th
Edition, 2002, Charotar Publishing House.
REFERENCE BOOKS:
1. Engineering Drawing by Dhananjay A. Jolhe, Tata McGraw Hill.
34
Engineering Physics Lab (NS-105(P))
Course Code NS-105(P) L-0, T-0, P-2

Name of the Course Engineering Physics Lab
Continuous Assessment Lab work 30%, Lab Record 25% Max Marks:
Viva/ Hands on 25%, Attendance 20% 25

Viva-voce examination will be related to the practicals performed/project executed by the
List of Experiments
1. To find the refractive index of a prism by using spectrometer.

2. To find the wavelength of sodium light by Newtons rings experiment.
3. To find the wavelength of sodium light by Michelson interferometer.
4. To study the laser beam characterstics like, wavelength using diffraction grating aperture &
divergence.
5. To study the variation of magnetic field with distance and to find the radius of coil by
Stewart and Gees apparatus.
6. To find the value of e/m for electrons by Helical method.
7. To compare the capacitances of two capacitors by Desauty Bridge.
8. To find the value of Plancks constant by using a photoelectric cell.
9. To calculate the hysteresis loss by tracing a B-H curve for a given sample
10. To determine the Hall co-efficient
11. To determine the band gap of an intrinsic semiconductor by four probe method.
12. To find the velocity of ultrasound in liquid.
13. To find out polarizability of a dielectric substance.
14. To determine the numerical Aperture of an optical fibre.
15. To determine the attenuation & propagation losses in optical fibres.
Note: Each student is required to perform at least ten experiments.
Books:
1. Practical Physics-S.L.Gupta&V.Kumar.
2. Advanced Practical Physics Vol. I & II S.P. Singh
35
BASIC ELECTRICAL ENGINEERING LAB (BE 101a(P))
Course Code BE 101a(P) L-0, T-0, P-2

Name of the Course Basic Electrical Engineering Lab
Continuous Assessment Lab work30%, Lab Record 25% Max Marks: 25
Viva/ Hands on 25%, Attendance 20%
Instructions for Paper setter/ Candidates

1. Performing a practical examination assigned by the examiner
2. Viva-voce examination
Viva-voce examination will be related to the practicals performed/projects executed by the
LIST OF EXPERIMENTS
1. To verify KCL and KVL.

2. To study various types of Electrical Meters.
3. To perform open circuit and short circuit test of Transformer.
4. Measurement of power by Three Voltmeter/Three Ammeter method.
5. Measurement of power in 3-phase system by two wattmeter method.
6. To perform direct load test of transformer and plot efficiency v/s load characteristics.
7. To perform direct load test of the DC shunt generator and plot load v/s current curve.
8. To study frequency response of series RLC circuit and determine resonance frequency
and Q factor for various values of R,L,C.
9. To study frequency response of parallel RLC circuit and determine resonance frequency
and Q factor for various values of R,L,C.
Note: All the practicals of Electrical should also be performed on breadboard.
36
BASIC ELECTRONICS ENGINEERING LAB (BE 101b(P)
Course Code BE 101b(P) Credits-2 L-0, T-0, P-2

Name of the Course Basic Electronics Engineering Lab.
Continuous Assessment Lab work 30%, Lab Record 25% Max Marks: 25
Instructions for Paper setter/ Candidates

1. Performing a practical examination assigned by the examiner
2. Viva-voce examination
Viva-voce examination will be related to the practicals performed/projects executed by the
LIST OF EXPERIMENTS
1. Familiarization with electronic components, and general purpose Laboratory equipment.

2. Use of CRO and function generator and calculation of amplitude, frequency, time period of
different types of ac signals.
3. Verification of Junction Diode and Zener Diode characteristic and determination of static
and dynamic resistance at the operating point
4. Verification of input and output characteristics of a Bipolar Junction Transistor and
determination of the operating point on load line.
5. Verification of input and output characteristics of a Field Effect Transistor and
determination of the operating point on load line.
6. Verification of Series and Parallel Resonance theory.
7. Operation of diode as different form of rectifier and effect of different types of passive
filters on the output.
8. Determination of frequency response of a RC coupled amplifier and determination of
bandwidth and signal handling capacity.
9. Use of OP-AMP as an inverting and non-inverting amplifier for different gains.
10. Verification of Uni-junction Transistor characteristics and relaxation oscillator
11. Rectifiers- Half wave , Full wave & Bridge rectifiers
Note: All the practicals should be performed on breadboard.
37
WORKSHOP PRACTICE-II (WS-102)
Course Code WS 102 L-0, T-0, P-3
Name of the Course Workshop Practice -II
Continuous Assessment Lab work 30%, Lab record 25%, Max. Marks: 25
Viva 25%, Attendance 20%
INSTRUCTIONS:

Fitting Shop: -
1. Drilling and Tapping in a M.S. piece.
2. To make a male-female joint (Taper type) of mild steel.
Machine Shop: -
1. To perform boring operation on lathe machine.
2. To perform knurling and threading operation on lathe machine.
3. Step turning operation on a lathe machine.
Carpentry and Pattern making Shop: -

1. To make a single piece pattern of connecting rod.
2. To make a self-cod pattern.
3. To make a split pattern.
Welding Shop: -
1. To make a V butt joint in horizontal position.
2. To make a V butt joint in vertical position.
3. To perform Gas welding operation.
Smithy and Forging: -

1. To make a cube from a circular bar.
2. To make a tong using hot forging operations.
3. To perform drawing down operation.
Foundry Shop: -
1. To make a mould and perform casting operation.
2. Study of casting defects and its remedies.
38
Sheet Metal Working Shop: -
Blanking and piercing die construction, press work materials, strip layout, bending dies, forming
dies, drawing operations, single and double action draw dies.
1. To make a Ring by Piercing.

2. To make a square shaped object by Bending and Forming Operation.
3. To Draw a Wire.
Suggested Reading: -
1. Workshop Technology by Chapman

2. Manufacturing Processes by Begman
3. Manufacturing Materials and Processes by J. S. Campbell
39
Semester -III
ENGINEERING ECONOMICS (HS-201)
Course Code HS-201 L-3, T-0, P-0

Name of the Course Engineering Economics
Lectures to be delivered 39 (1 Hr Each) (L = 39 for each semester)
INSTRUCTIONS:
type, which will cover the entire syllabus. Section A, B, C & D will have two questions from
the respective sections of the syllabus. Each section will have a weightage of 20% of the total
marks of the semester end examination for the course.
question from each of the sections A, B, C & D of the question paper and all the subparts of the
Section-A
Economics: Definition, nature and scope of economics, need &significance of economics in

Engineering, Economic Systems- Meaning of capitalism, socialism and mixed economy
Demand: Meaning, determinants of demand, demand curve, law of demand, exception to the
law of demand, increase &decrease in demand, contraction &extension of demand, Elasticity of
demand, Methods of measuring Elasticity of demand
Supply: Law of supply, extension &contraction of supply, increase & decrease in Supply,
Elasticity of supply
Section-B
Cost of Production: Concept, types, Relation between average & marginal cost.
Theory of Production: Laws of returns- Law of variable proportions and law of returns to Scale,
Break Even Analysis.
Price & Output Determination: Price determination under perfect competition, monopoly,
monopolistic competition &oligopoly.
Section-C
Monetary policy- Meaning, objectives, methods, Fiscal policy- Meaning &Objectives of fiscal
policy In a developing country like India, Functions of Reserve Bank of India and commercial
banks.
40
Economics & Business Environment- Business/Trade Cycles- Meaning, Characteristics &
classification, Inflation Effect, Foreign capital &economic development, Engineering Economics
Analysis, Economics Analysis in the public and regulated sectors.
Section D
Indian Economy: - Characteristics of Indian economy, Planning in India, Development

&Growth in India. Overall Economic policy since independence, Input & output analysis,
Problem of unemployment in India. Concept of sustainable development &inclusive growth in
India. Policy of globalizations, liberisation & privatization. Analysis of state &union budgets.
TEXT BOOKS:
1. Modern Micro Economics by Koutsoyannisa, MC Millen
2. Principles of Engineering Economics Analysis by John A. White, Kenneth E. Case
and David B. Pratt Wiley India
REFERENCE BOOKS:
1. Business Economics by K. P. M. Sundharam, Sultan Chand &Sons
2. Elementary Economics Theory by K.K Dewett & J. D. Verma, S.Chand Publication
41
STRENGTH OF MATERIALS (CE-211)
Course Code CE-211 L-3, T-1, P-0

Name of the Course Strength of Materials
INSTRUCTIONS:
Section-A
Analysis of stresses: Body forces, Surface forces, Internal Force, Stress at a point, Components
of stress in rectangular coordinates, Stress tensor, Principal stresses, Transformation, Equations,
Stress invariants, Plane stress, Mohrs circle for plane stress, Octahedral stresses, Differential
equations of equilibrium, components of stresses in cylindrical and Polar coordinates.
Analysis of Strain: Deformable bodies, Concepts of normal strain and shear strain, Strain
components at a point, Transformation equations, Principal strains, Mohrs circle of strains,
Compatibility conditions, Displacement equation of equililibirum, Plane strain.
Section-B
Theories of Failure: Failure of Materials, Failure theories of ductile materials, Maximum
principle stress criterion (Rankine, Lames), Maximum Principle strain Theory (St. Venants),
Maximum Strain Energy Theory (Beltrami-Haighs), Maximum Shear Stress Theory (Tresca-
Guest and Coulomb), Maximum Distortional Stress or Octahedral Shear Stress Theory (Von-
Mises-Maxwell-Huber-Henkeys), Failure Theories of brittle materials (Mohr-Coulomb).
Unsymmetric Bending and Shear Centre: Bending about a principle axis, bending about
arbitrary Axis, Shear Centre.
Section-C
Slope and Deflection of Beams: The moment curvature relation, Double integration method,
Macaulays method.
Buckling of Columns: Stable and unstable equilibrium, Critical load, Eulers Curves, Rankines
formula, Secant formula, Analysis of eccentrically and laterally loaded columns, Columns with
initial curvature.
42
Section-D
Energy Principles: Concept of Strain Energy, Strain Energy due to axial tension/compression,
bending, shear and Torsion. Complementary strain Energy, Virtual Work Theorem, Total
potential Energy theorem, Castiglainos First Theorem, Complementary Virtual Work Theorem,
Total complementary Potential energy Theorem, Castiglainos Second Theorem, Maxwell
Bettis Reciprocal Theorem.
Combined Stresses: Beam subjected to bending and shear, shaft subjected to bending and
torsion,
TEXT BOOKS:
1. Fundamentals of Strength of Materials, by Bebabrata Nag and Abhijit Chanda, Wiley
India.
2. Strength of Materials, H C Hibbler, Pearson
REFERENCE BOOKS:
1. Mechanics of Solids, by Abdul Mubeen, Pearson
2. Fundamentals of Solid Mechanics, by M L Gambhir, PHI Learning
3. Strength of Timoshenko, S.P. and. Young D.H., Elements of strength of materials,
Affiliated East-West Press, New Delhi.
4. Strength of materials by Timoshenko, S.P., CBS Publisher, Delhi.
5. Mechanics of materials, by Popov,Egor Paul, Nagarakam,S, , PrenticeHall.
43
BUILDING CONSTRUCTION AND MATERIALS (CE-212)
Course Code CE-212 L-03, T-01,P-0

Name of Course Building Construction and Materials
Semester End Examination MM: 100 Min. Marks : 40 Time Allowed : 3 Hrs.
Continuous Assessment (based on sessional tests 50%) Max. Marks : 50
Tutorial/Assignment: 30%, Quiz/Seminar: 10%, Attendance: 10%.
INSTRUCTIONS:
1. For Paper Setters: The question paper will consist of five sections A,B,C,D & E.
Section E will be compulsory; it will consist of a single question with 10-20 subparts of
short answer type, which will cover the entire syllabus. Section A,B,C & D will have
two questions from the respective sections of the syllabus. Each section will have a
weightage of 20% of the total marks of the semester end examination for the course.
2. For Candidates: Candidates are required to attempt five questions in all selecting one
question from each of the sections A,B,C & D of the question paper and all the subparts
of the questions in Section E.
SECTION-A
BRICK & STONE MASONRY: Various terms used, types, tools used, bonds in brick work,
dressing of stones, applications for lifting stones.
PARTITION AND CAVITY WALLS: Types of non bearing partition-brick partitions, clay
block partitions, timber partitions and glass partitions, construction of a masonry cavity walls.
DAMP PREVENTION: Sources of dampness, effects of dampness, prevention of dampness,

materials used in damp proofing course.
(10 Lect)
SECTIONS-B
ROOFS: Types terms used in sloping roof, king post truss, queen post truss, simple steel roof
trusses.
FLOORS: Components of floor, brick floors, cement concrete floors, terrazzo flooring, mosaic
floorings, tiled flooring.
DOORS & WINDOWS: Locations, sizes general types of door movement, various types of
doors and windows.
(9 Lect.)
SECTION-C
STONES : Stone as building material, criteria for selection, tests on stones, deterioration and
preservation of stone work.
44
BRICKS: Classification, manufacture of clay bricks, test on bricks-compressive strength, water
absorption, efflorescence. Bricks for special use-Refractory bricks, cement and concrete hollow
blocks and lightweight concrete blocks.
TILES, TERRA COTTA: Manufacturing of tiles and terra-cotta, types of terra-cotta, uses of
terra cotta.
LIME, CEMENT AND MORTAR: Preparation of lime mortar; cement ingredients-

manufacturing process, types and grades, properties of cement and cement mortar-hydration,
compressive strength, tensile strength, soundness and consistency and setting time.
STEEL: Types of steel, marketable forms, stress-strain behavior.

(9 Lect.)
SECTION-D
CONCRETE: Ingredients, manufacture, batching plants, properties of fresh concrete-slump,
flow and compaction; principles of hardened concrete-compressive, tensile and shear strength,
modulus of rupture; tests-mix specification, mix proportioning, IS method, high strength
concrete and HPC, other types of concrete.
TIMBER: Market forms, industrial timber-plywood-veneer-thermocole-panels of laminates.
PAINTS AND VARNISHES: Constituents of paints, types of paints, types, constituents and
characteristics of varnishes.
INTRODUCTION TO POLYMERS: Polymetric materials, PVC, Polyester, HDPE, CDPE,

ceramics, fibre glass and their applications in civil engineering.
(10 Lect.)
TEXT BOOKS:
1. Building Construction by Sharma & Kaul,

2. Engineering Materials by Surinder Singh,
REFERENCE BOOKS:
1. Properties of concrete by A M Naville, PEARSON

2. Construction Technology Analysis and Choice by Tony Bryan Wiley India
3. Civil Engineering Materials by Shan Somayaji, Pearson
4. Concrete Technology by A.M. Naville, PEARSON
5. Concrete Technology by A.M. Santhakumar, Oxford
6. Building Construction by B.C. Punmia
7. Building Construction, Sushil Kumar
8. Building Construction, Gurcharan Singh, Standard Pub., N.Delhi
45
FLUID MECHANICS (CE 213)

Name of Course FLUID MECHANICS
30%, Quiz/ Seminar: 10 %, Attendance: 10 %. MM: 50
INSTRUCTIONS:
SECTION A
INTRODUCTION: Definition, units, properties of fluids, Newtonian and non Newtonian fluids.
FLUID STATICS: Basic equations, pressure, pressure measurement, stability of floating bodies,
pressure diagram, hydrostatic forces on submerged bodies, buoyancy and floatation. (10 Lect)
SECTION B
FLUID KINEMATICS: Flow characteristics, continuity equation, acceleration of fluid
particles, Continuity Equation, rotational and irrotational motion, circulation and vorticity,
velocity potential and stream function, streamlines, equipotential lines, flow net - method, uses
of flow net.
FLUID DYNAMICS: Eulers equation, Bernoullis equation, application of Bernoullis
equation-orificemeter, venturimeter, pitot tube etc., flow through orifice, mouthpiece, weir and
notches, impulse momentum equation and its application to pipe junction, bends, stationary flat
and curved vanes moment of momentum equation. (10 Lect)
SECTION C
FLOW THROUGH PIPES: Reynolds experiment, energy losses, laws of fluid friction, Darcy-
Weisbach equation, equivalent pipe, pipes in series and parallel, branched pipes, pipe networks.
LAMINAR FLOW AND TURBULENT FLOW: Laminar flow through circular pipes,
parallel plates, Stokes law, measurement of viscosity, transition from laminar to turbulent flow.
(9 Lect)
46
SECTION D
DIMENSIONAL ANALYSIS AND SIMILITUDE: Dimensional homogeneity, methods of
dimensional analysis, model analysis, similitude types of similarities, force ratios, similarity
laws, model classification, scale effects.
BOUNDARY LAYER THEORY: Types, boundary layer thickness and equations, momentum
integral equation boundary layer on rough surfaces, total drag on flat plate due to laminar and
turbulent boundary layer, boundary layer separation and its control. (10 Lect )
TEXT BOOKS:
1. Fluid Mechanics by Dr A. K. Jain,
2. Hydraulics and Fluid Mechanics : P.N. Modi and S. M. Seth,
REFERENCE BOOKS:
1. Fluid Mechanics : F. M. White,
2. Fluid Mechanics : Wiley and Streeter ,
3. Introduction to Fluid Mechanics, by Fox, Pritchard and McDonald, Wiley
4. Fundamental of Fluid Mechanics by Munson, Young, Okiishi and Huebsch, Wiley
5. Introduction to Fluid Mechanics by Edward J Shaughnessy, Ira M Katz and James P
Schaffer, Oxford
47
SURVEYING - I (CE 214)

Name of Course SURVEYING - I
30%, Quiz/ Seminar: 10 %, Attendance: 10 %. MM: 50.
INSTRUCTIONS:
SECTION A
INTRODUCTION: Introduction, history of surveying, definition of surveying, primary
divisions of surveying, object and classification of surveying, principles of surveying, units of
measurement, representation of scale, duties of surveyor, office work of a surveyor, care and
adjustments of instruments, accuracy & precision, sources of errors, types of errors, degree of
accuracy, order of accuracy.
MEASUREMENT OF DISTANCES: Introduction, approximate methods, surveying chains &
tapes, unfolding and folding of a chain, steel bands, instruments for chaining & taping,
measurement by tape & chain, errors in tape measurements and their corrections, chain
corrections, testing and adjusting of a chain, chaining on flat and sloping ground, obstacle in
chaining, direct & indirect methods of ranging, modern trends. (10 Lect)
SECTION B
COMPASS & CHAIN TRAVERSING: Methods of traversing, principles, basic definitions,
bearings & meridians, prismatic compass, surveyors compass, azimuthal & quadrantal bearing
systems, true north & magnetic north, magnetic declination, local attraction and its correction.
THEODOLITE & THEODOLITE TRAVERSING: Vernier theodolite, microscopic
theodolite, construction, temporary & permanent adjustments, measurements of horizontal &
vertical angles, methods of repetions & reiteration, sources of errors, checks in traversing,
adjustments of traverse, degree of accuracy, omitted measurements. (10 Lect)
SECTION C
LEVELLING: Definitions of terms, principles of leveling i.e spirit, trigonometric, barometric,
types of levels, methods of spirit leveling, leveling staffs, booking & reduction in field book,
balancing of sights, errors-curvature & refraction, distance of visible horizon, reciprocal leveling
& its merits, sensitivity of bubble tube.
48
CONTOURING: Methods of relief representations, contour, contour interval, horizontal
equivalent, contour gradient, factors affecting contour interval, characteristics of contours, direct
& indirect methods of contouring, uses of contour maps. (9 Lect)
SECTION D
AREA, VOLUME AND MINOR INSTRUMENTS: Methods of computation of areas from
field notes and plan, construction and use of planimeter, volume computations from-section,
earthwork, prismoidal and curvature corrections, capacity off reservoir, volume of borrowpits,
hand level, abney level box sextant, site square, pantagraph, ceylonghat tracer, Indian patter
clinometers
PLANE TABLE SURVEYING: Principles, merits & demerits instruments and other
accessories, methods used, radiation, traversing, resection, intersection and their uses. Two and
three point problems, uses of tangent clinometers.
TACHEOMETRY: Definitions, general principles of stadia system, fixed and movable hair
methods, inclined sights with staff vertical, inclined sight with statt normal to the line of sight.
Determination of tacteometric constants, analytic lens, field work and seconds, tangential
system, subtense bar method, auto reduction techeometer. (10 Lect )
TEXT BOOKS:
1. Surveying Volume I and II by B C Punmia, Lakshmi Publication
2. Surveying Volume I and II by K R Arora,
REFERENCE BOOKS:
1. Engineering Survey by W. Schofield
2. Advance Surveying by R Agor
3. Advanced Surveying by Satheesh Gopi, R Sathikumar and N Madhu by Pearson
4. Surveying, Vol. I, S.K. Duggal, Tata Mc Graw Hill Publishing Co. Ltd., New Delhi
5. Surveying and Levelling, T.P. Kanetker and Kulkarni, PuneVidyarthi Gruha Prakashan
6. Surveying for Engineers by J.Uren and W.F.Price, The Macmillan Press Ltd., London.
7. Surveying Principles and Applications by B.F.Kavanagh and D.J.G. Bird, prentice Hall,
Englewood Cliffs, New Jersey.
8. Surveying and Levellings by N. N. Basaak, Tata Mc Graw Hill Publishing Co. Ltd
49
ENGINEERING MATHEMATICS-III (NS-206)

Name of Course Engineering Mathematics-III
30%, Quiz/ Seminar: 10 %, Attendance: 10 %. MM: 50.
INSTRUCTIONS:
Section-A
1. PARTIAL DIFFERENTIAL EQUATIONS
Formation and solutions of partial differential equations, Lagranges linear equation of
the first order, non linear equations of first order, charpit method, Homogenous linear partial
differential equation with constant coefficients, rules for complementary function and particular
integral, non-homogenous linear partial differential equations, Method of separation of variables,
Solution of wave equations, Heat flow equations, Laplaces equations and their applications to
engineering problems.
Section-B
2. SPECIAL FUNCTIONS:
Power series solution of differential equations, Frobenius method, Bessel's equation, Bessel
functions of the first and second kind, Recurrence relations of Bessel functions, Generating
functions, Orthogonality of Bessel functions, Legendre's equation, Legendre polynomial,
Recurrence relations of Legendre's functions, Rodrigues formula, Orthogonality of Legendre
polynomials, Error function and its properties.
Section-C
3. INTEGRAL TRANSFORMS
Laplace Transforms of standard functions and their properties, Inverse Laplace
Transforms, General Properties of inverse Laplace transforms and Convolution Theorem,
Laplace Transforms of periodic functions, Laplace transform of Bessel functions and Error
function, Dirac-delta Function, Heavisides Unit Function, Applications to linear simultaneous
differential equations. Fourier Integral, Fourier Transform, Fourier sine and cosine transforms,
finite Fourier transform, Convolution theorem for Fourier Transform and Parsevals Identity for
Fourier Transform.
50
Section-D
4. FUNCTIONS OF COMPLEX VARIABLE
Limit and derivative of complex functions, Cauchy-Riemann equations, Analytic
functions, Entire functions and its applications, Conformal mapping and standard
transformations, Complex integration, Cauchys theorem and Cauchys integral formula (without
proof), Series of complex terms, Taylors series and Laurents series (without proof), Zeros of
analytic functions, isolated singularity, removable singularity, Poles, essential singularity,
Residue, Residue theorem and their applications
TEXT BOOKS
1. Advanced Engineering Mathematics: by Erwin Kreyszig . John Wiley and Sons, NC,
New York.
2. Partial Differential Equation for Engineers and Scientists: by J.N. Sharma and Kehar
Singh Narosa Publishing House, New Delhi/ Alpha Science Int. Ltd, UK.
3. Advanced Engineering Mathematics: by R. K. Jain & S. R. K Iyengar, Narosa Pub.
House.
4. Complex Variables Theory and Applications: by HS Kasana, PHI Learning Private
Limited New Delhi, (2008).
REFERENCE BOOKS
1. Advanced Engineering Mathematics: by C. R. Wylie & L. C. Barrett, McGraw Hill.
2. Elements of Partial Differential Equations: by Ian N. Sneddon, McGraw-Hill, Singapore.
4. Calculus and Analytic Geometry, by Thomes, G.B, Finney, R.L. Ninth Edition, Peason
Education.
5. Advanced Engineering Mathematics,by Peter. V. O. Nil, Wordsworth Publishing
Company.
6. Advanced Engineering Mathematics, by Jain, R.K and Lyengar, S.R.K., Narosa
Publishing Company.
7. Higher Engineering Mathematics, by Grewal, B.S., Khanna Publishers, New Delhi.
8. Engineering Mathematics, by Taneja, H.C., Volume-I & Volume-II, I.K. Publisher.
9. Differential Equations: by Shepley L. Ross, John Wiley & Sons, New York.
51
BUILDING MATERIAL LAB CE-212 (P)
Course Code CE-212(P) L-0, T-0,P-2

Name of Course Building Material Lab
Lectures to be delivered 26 (P-26, for each semester)
Semester End Examination MM: 25 Min. Marks : 10
Continuous Assessment Lab work 30%, Lab record 25%, Viva Max. Marks : 25
25%, Attendance 20%
INSTRUCTIONS:
(i) Performing a practical exercises assigned by the examiner.

(ii) Viva-voce examination.
Vive-voce examination will be related to the practicals performed/project executed by the
LIST OF EXPERIMENTS
Sr. Title of the Experiment

No.
A. Stone & Bricks
1 To identify the various types of stones and their applications.
2 To identify the various bricks and their applications.
3 To conduct the field test on bricks viz hardness, shape and size, soundness, colour and
strength.
4 To determine the amount of water absorbed by the bricks.
5 To determine the crushing strength of bricks using compressive testing machine.
B. Cement
6 To determine the fineness of cement by sieve method.
7 To determine the normal consistency of cement paste.
8 To determine the initial and final setting times of cement.
C. Aggregates
9 To determine the percentage bulking of sand in moist condition.
10 To determine the specific gravity of fine and coarse aggregates.
D. Metals
11 To conduct the tension test on the given mild steel specimen to determine yield,
strength, ultimate strength, breaking strength, percentage, elongation and youngs
modulus.
52
FLUID MECHANICS LAB CE-213(P)
Course Code CE-213(P) L-0, T-0, P-2

Name of Course Fluid Mechanics Lab
Semester End Examination MM: 25 Min. Marks- 10
INSTRUCTIONS:

LIST OF EXPERIMENTS:
1. To determine the metacentric height of a ship model.

2. Verification of Bernoullis theorem.
3. To calibrate a venturimeter and to determine its coefficient of discharge
4. To calibrate an orifice meter and study the variation of the coefficient of
discharge with the Reynolds number
5. To study the flow over V- notch (weir) and Rectangular notch and to find their
coefficient of discharge
6. To determine the coefficient of discharge of a mouth piece.
7. To verify the momentum equation experimentally.
8. To determine the coefficient of friction of pipes of different diameters.
9. To determine the form losses in a pipe line.
10. To obtain the surface profile on the total heads distribution of a forced vortex
53
SURVEYING LAB-I CE-214(P)

Name of Course Surveying Lab-I
INSTRUCTIONS:

1. To determine the difference in elevation of two given points.

2. Profile levelling and cross sectioning of a given route.
3. To measure the horizontal angle by the method of reiteration and repetition, theodolite
traversing and error adjustment.
4. To prepare the contour map of an area by the method of radial lines.
5. Determination of elevation of top of tower using theodolite
6. Plane tabling by the method of radiation and intersection.
7. Solution of Three point problem in plane tabling
8. Setting out of simple circular curve by one theodolite and by two theodolite method.
54
BUILDING DRAWING CE-215(P)

Name of Course Building Drawing
INSTRUCTIONS:
End semester Examination will consist of Viva-voce examination related to the drawing sheets
prepared by the candidate related to the paper during the course of the semester.
OBJECTIVE:
The student is expected to know local building rules and national building code provisions. At
the end of this course the student should be able to draft building drawings (Plan, elevation and
sectional views) in accordance with development and control rules satisfying orientation and
functional requirements for the following:
SYLLABUS:
Working drawings for
1. Residential buildings: Flat and pitched roof cottages, bungalows and flats (single storied
and double storied) (4 sheets)
2. Public buildings schools, offices, libraries, restaurants, commercial complexes (3sheets)
3. Industrial buildings North light roof structures Trusses (2 Sheets)
4. Preparation of site plan and plan as per building rules. (2 sheets)
5. Plumbing: water supply and sanitary drawings for residential buildings. (1 sheet)
TEXT BOOKS
1. Civil Engg. Drawing & House Planning Varma B. P., Khanna publishers, Delhi
2. Building drawing & detailing Balagopal & T. S. Prabhu, Spades Publishers, Calicut.
REFERENCE BOOKS
1. Building drawing Shah. M. G., Tata McGraw-Hill
2. Building planning & Drawing Kumaraswamy N., Kameswara Rao A., Charotar Publishing
3. Shah, Kale and Patki, Building Drawing with integrated approach to built environment, Tata
McGraw-Hill.
4. B. P. Varma, Civil Engineering drawing and House Planning, Khanna Publishers, Delhi.
5. Gurucharan Singh, Subhash Chander Sharma, Civil Engineering drawing, Standard
Publishers distributors, Delhi.
6. National Building code, Local building byelaws.
55
Semester 4th
HUMAN VALUES AND PROFESSIONAL ETHICS-III (HS-203)
Course Code HS-203 L-02, T-01, P-02

Name of Course Human Values and Professional Ethics
Lectures to be delivered 52 (L-26, P-26 for each semester)
Continuous Assessment (based on sessional tests 50%) Tutorial/
Assignment: 30%, Quiz/ Seminar: 10 %, Attendance: 10 %. MM: 50.
INSTRUCTIONS:
1. For Paper Setters: The question paper will consist of six sections A, B, C, D, E & F. Section
F will be compulsory, it will consist of a single question with 10-15 subparts of short answer
type, which will cover the entire syllabus. Section A, B, C, D & E will have two questions from
2. For candidates: Candidates are required to attempt six questions in all selecting one question
from each of the sections A, B, C, D & E of the question paper and all the subparts of the
OBJECTIVES:
a. To help the students appreciate the essential complementarily between VALUES and
SKILLS to ensure sustained happiness and prosperity which are the core aspirations
of all human beings.
b. To facilitate the development of a Holistic perspective among students towards life,
profession and happiness, based on a correct understanding of the Human reality and
the rest of Existence. Such a holistic perspective forms the basis of Value based living
in a natural way.
c. To highlight plausible implications of such a Holistic understanding in terms of ethical
human conduct, trustful and mutually satisfying human behavior and mutually
enriching interaction with Nature.
Thus, this course is intended to provide a much needed orientation input in Value Education to
the young enquiring minds.
COURSE METHODOLOGY:
The methodology of this course is universally adaptable, involving a systematic and rational
study of the human being vis--vis the rest of existence.
It is free from any dogma or value prescriptions.
It is a process of self-investigation and self-exploration, and not of giving sermons.
Whatever is found as truth or reality is stated as proposal and the students are facilitated to
verify it in their own right based on their Natural Acceptance and Experiential Validation.
This process of self-exploration takes the form of a dialogue between the teacher and the
students to begin with, and within the student himself/herself finally.
This self-exploration also enables them to evaluate their pre-conditionings and present
beliefs.
56
Content
SECTION A: Course Introduction - Need, Basic Guidelines, Content and Process for Value
Education
1. Understanding the need, basic guidelines, content and process for Value Education
2. Self Explorationwhat is it? - its content and process; Natural Acceptance and
Experiential Validation- as the mechanism for self exploration
3. Continuous Happiness and Prosperity- A look at basic Human Aspirations
4. Right understanding, Relationship and Physical Facilities- the basic requirements for
fulfillment of aspirations of every human being with their correct priority
5. Understanding Happiness and Prosperity correctly- A critical appraisal of the current
scenario
6. Method to fulfill the above human aspirations: understanding and living in harmony at
various levels
SECTION B: Understanding Harmony in the Human Being - Harmony in Myself!
7. Understanding human being as a co-existence of the sentient I and the material Body
8. Understanding the needs of Self (I) and Body - Sukh and Suvidha
9. Understanding the Body as an instrument of I (I being the doer, seer and enjoyer)
10. Understanding the characteristics and activities of I and harmony in I
11. Understanding the harmony of I with the Body: Sanyam and Swasthya; correct appraisal
of Physical needs, meaning of Prosperity in detail
12. Programs to ensure Sanyam and Swasthya - Practice Exercises and Case Studies will be
taken up in Practice Sessions.
SECTION C: Understanding Harmony in the Family and Society- Harmony in Human-
Human Relationship
13. Understanding harmony in the Family- the basic unit of human interaction
14. Understanding values in human-human relationship; meaning of Nyaya and program for
its fulfillment to ensure Ubhay-tripti;
Trust (Vishwas) and Respect (Samman) as the foundational values of relationship
15. Understanding the meaning of Vishwas; Difference between intention and competence
16. Understanding the meaning of Samman, Difference between respect and differentiation;
the other salient values in relationship
17. Understanding the harmony in the society (society being an extension of family):
Samadhan, Samridhi, Abhay, Sah-astitva as comprehensive Human Goals
18. Visualizing a universal harmonious order in society- Undivided Society (Akhand Samaj),
Universal Order (Sarvabhaum Vyawastha )- from family to world family!
- Practice Exercises and Case Studies will be taken up in Practice Sessions.
SECTION D: Understanding Harmony in the Nature and Existence - Whole existence as
Co-existence
19. Understanding the harmony in the Nature
20. Interconnectedness and mutual fulfillment among the four orders of nature-recyclability
and self-regulation in nature
21. Understanding Existence as Co-existence (Sah-astitva) of mutually interacting units in
all-pervasive space
22. Holistic perception of harmony at all levels of existence- Practice Exercises and Case
Studies will be taken up in Practice Sessions.
57
SECTION E: Implications of the above Holistic Understanding of Harmony on
Professional Ethics
23. Natural acceptance of human values
24. Definitiveness of Ethical Human Conduct
25. Basis for Humanistic Education, Humanistic Constitution and Humanistic Universal
Order
26. Competence in professional ethics:
a) Ability to utilize the professional competence for augmenting universal human order,
b) Ability to identify the scope and characteristics of people-friendly and ecofriendly
production systems,
c) Ability to identify and develop appropriate technologies and management patterns for
above production systems.
27. Case studies of typical holistic technologies, management models and production systems
28. Strategy for transition from the present state to Universal Human Order:
a) At the level of individual: as socially and ecologically responsible engineers,
technologists and managers
b) At the level of society: as mutually enriching institutions and organizations
TEXT BOOK:
1. R R Gaur, R Sangal, G P Bhagaria, 2009, A Foundation Course in Value Education.
REFERENCE BOOKS:
1. Ivan Illich, 1974, Energy & Equity, The Trinity Press, Worcester, and HarperCollins,
USA
2. E.F. Schumacher, 1973, Small is Beautiful: a study of economics as if people mattered,
Blond & Briggs, Britain.
3. A Nagraj, 1998, Jeevan Vidya ek Parichay, Divya Path Sansthan, Amarkantak.
4. Sussan George, 1976, How the Other Half Dies, Penguin Press. Reprinted 1986, 1991
5. PL Dhar, RR Gaur, 1990, Science and Humanism, Commonwealth Purblishers.
6. A.N. Tripathy, 2003, Human Values, New Age International Publishers.
7. Subhas Palekar, 2000, How to practice Natural Farming, Pracheen (Vaidik) Krishi Tantra
Shodh, Amravati.
8. Donella H. Meadows, Dennis L. Meadows, Jorgen Randers, William W. Behrens III,
1972, Limits to Growth Club of Romes report, Universe Books.
9. E G Seebauer & Robert L. Berry, 2000, Fundamentals of Ethics for Scientists &
Engineers , Oxford University Press
10. M Govindrajran, S Natrajan & V.S. Senthil Kumar, Engineering Ethics (including Human
Values), Eastern Economy Edition, Prentice Hall of India Ltd.
11. Values and Ethics in Business & Professional, Samita Manna & Suparna Chakraborti,
PHI Learning Private Limited.
RELEVANT CDS, MOVIES, DOCUMENTARIES & OTHER LITERATURE:
1. Value Education website, http://www.uptu.ac.in
2. Story of Stuff, http://www.storyofstuff.com
3. Al Gore, An Inconvenient Truth, Paramount Classics, USA
4. Charlie Chaplin, Modern Times, United Artists, USA
5. IIT Delhi, Modern Technology the Untold Story
58
NUMERICAL METHODS FOR ENGINEERS (NS-207)

Name of Course Numerical Methods for Engineers
INSTRUCTIONS:
SECTION A
SOLUTION OF ALGEBRAIC AND TRANSCENDENTAL EQUATIONS: Bisection
method, Method of false position, secant method, Iteration method, Newton-Raphson method
and Generalized Newton-Raphson method, Rate of convergence and condition of convergence,
solution of simultaneous equations by Iteration method and Newton-Raphson method
SOLUTION OF SIMULTANEOUS ALGEBRAIC EQUATIONS: Partial and Complete
Pivoting, Gauss Elimination method, Gauss Jordan method, Jacobis method, Gauss-Seidal
method, Relaxation method and LU-decomposition method.
SECTION-B
FINITE DIFFERENCE AND INTERPOLATION: Errors and approximation analysis,
Interpolation, Various difference operators and relation between them, Newtons forward and
backward interpolation formulae, Central difference Interpolation formula, Gausss forward and
backward interpolation formulae, Stirling formula, Bessel formula, Lagranges interpolation
formula of unequal intervals, Newtons divided difference formulae.
SECTION-C
NUMERICAL DIFFERENTIATION AND INTEGRATION: Numerical differentiation:
Derivatives using Newton forward, backward and central difference formulas, Derivatives using
Gauss forward and backward formulas, Derivatives using Bessel formula, Derivatives using
Newton divided difference formulas, Maxima and minima of tabulated functions.
NUMERICAL INTEGRATION: Newton-Cotes Quadrature formula, Trapezoidal rule,
Simpsons 1/3rd and 3/8th rules, Booles and Weddles rules, Errors and accuracy of these
formulae (Trapezoidal rule, Simpsons 1/3rd rule) Rombergs integration.
59
SECTION-D
NUMERICAL SOLUTIONS OF ORDINARY EQUATIONS: Picard method, Taylors series
method, Eulers method, Runges method, Runge-Kutta method, Predictor- Corrector Methods:
Milnes method and Adams-Bashforth method.
NUMERICAL SOLUTIONS OF PARTIAL DIFFERENTIAL: Finite difference
approximations of partial derivatives, solution of Laplace equation (Standard five-point formula
and Diagonal five-point formula), Solution of Poisson equation.
TEXT BOOKS:
1. Numerical methods for Scientific & Engg. Computations: M. K. Jain, S. R. K. Iyengar &
R. K. Jain; Wiley Eastern Ltd.
2. Introductory Methods of Numerical Analysis Engineers & Sciences: S. S. Sastry, PHI
Learning Private Limited New Delhi, (2009).
REFERENCE BOOKS:
1. Numerical Methods in Engineers & Sciences : J.N Sharma : Narosa Publishers.
2. Numerical Methods in Engg. & Sciences : B.S.Grewal : Khanna Publishers.
3. Computer Oriented Numerical methods: U. Rajaraman Orebtuce; Hall of India.
4. Introduction to Numerical Analysis: C. E. Froberg; Addison Wesley.
60
STRUCTURAL ANALYSIS-I (CE-221)

Name of Course Structural Analysis-I
INSTRUCTIONS:
SECTION A
Fundamentals - Classification of Structure, Types of Load, Response/ behavior of structure,
Principle of superposition, Equations of Equilibrium, Determinacy (Static and Kinematic) and
stability.
Force Response in Statically Determinate Structures Review of support Reactions, Internal
Forces in Beams and Axial Forces in Trusses. Axial Forces in Cables subjected to concentrated
loads and full or partial uniformly distributed loads. Concept Funicular Arches and internal
forces in three hinged arches, Internal Forces in Frames,
SECTION - B
Influence Lines Influence line diagrams for beams, Muller Breslaus Principle for qualitative
influence lines, Influence lines for floor girders, Influence line diagrams for Trusses, Maximum
influence at a point due to single concentrated rolling load, pair of rolling loads, series of rolling
loads and uniformly distributed moving loads, Absolute maximum shears and moments.
SECTION- C
Displacement Response in Statically Determinate Structures - Deflection in Beams using
Energy Methods, Moment-Area method, Conjugate Beam method, Principle of Virtual work,
method of virtual work for trusses, method of virtual work for beams and frames, Castiglianos
theorem for trusses, beams and frames, unit load method.
61
SECTION - D
Approximate analysis of Statically Indeterminate Structures: Vertical loads on building
frames, Lateral loads on building frames, portal method and Cantilever method.
TEXT BOOKS:
1. Structural analysis by Menon, Devdas, Narosa Publishing House, New Delhi.
2. Structural Analysis by Hibbeler, R.C., Pearson Education Asia publication, Delhi.
REFERENCE BOOKS:
1. Fundamentals of Structural Analysis by Harry H West and Louis F Geschwindner, Wiley
India.
2. Theory of structures, by Punmia, B.C., Laxmi Publications, New Delhi
3. Analysis of Structures, Vazirani, V.N. and Ratwani, M.M., Khanna Publishers, New Delhi.
4. Analysis of Statically Determinate Structures by P. Dayaratnam,
5. Basic Structural Analysis, C. S. Reddy,
6. Elementary Structural Analysis by Willbur J.B. & C.H.Norris & Utku , Mc Graw Hill Book
62
GEOTECHNICAL ENGINEERING-I (CE-222)

Name of Course Geotechnical Engineering-I
INSTRUCTIONS:
SECTION A
INTRODUCTION: Definition of soil, rock, soil mechanics and foundation engineering, soil
formation, soil structure, soil map of India.
SOIL PROPERTIES : Basic definitions, phase diagram, water content, specific gravity, void
ratio, porosity, unit weight, weight volume relationships, index properties of soil and their
determination, classification of soils, degree of saturation, density index.
SECTION B
PERMEABILITY AND SEEPAGE : Darcys law and its validity, seepage velocity, discharge
velocity, constant and variable head permea-meter, pumping in and out tests, permeability of
stratified soils, factors affecting permeability, laplaces equation, flow potential flow net and its
properties, different methods of drawing flownets, seepage pressure, quick sand, exit gradient,
piping, design of filter, principle of total and effective stresses, capillarity conditions in soil,
effective and pore pressures.
STRESSES IN SOILS : Need for finding stress distribution in soil, assumptions in elastic
theories, Boussinesqs equation for point, line, circular and rectangular loads, Westergaads
formula for point load, comparison of Boussinesqs and Westergaards equation, concept and use
of pressure bulbs, principle and use of New marks influence chart, contact pressure.
SECTION C
COMPACTION : Mechanism of compaction, objective of compaction, measurement of
compaction, factors affecting compaction, optimum moisture content, Standarad Proctor test,
Modified Proctor test, effect of moisture content and compactive effort on dry density, zero air
void curve, compaction of cohesionless soils, field compaction, field control of compaction.
CONSOLIDATION: Mechanism of consolidation, e-logp curves, basic definitions, estimation
of preconsolidation pressure, normally consolidation and over consolidation ratio, Terzaghis
63
theory of one dimensional consolidation, assumptions, governing equation, standard solution,
laboratory determination of consolidation properties of soil, magnitude and rate of consolidation,
settlements, secondary consolidation, compression characteristics of clays and settlement
analysis.
SECTION D
SHEAR STRENGTH : Normal, shear and principal stresses, Coloumbs equation, Mohrs
stress circle, Mohr-Coloumb failure criteria, laboratory determination of shear parameters of soil
by direct shear tests, triaxial test, unconfined compression test, Vane shear test, Consolidated
drained, consolidated undrained and unconsolidated undrained shear test, pore pressure
parameters, Lambes p-q diagram.
SOIL STABILIZATION: Mechanical stabilization, cement stabilization, lime stabilization,
Chemical, bitumen, stabilization by heating, electrical stabilization and sand columns.
TEXT BOOKS:
1. Soil Mechanics and Foundation Engineering by B.C. Punmia, Laxmi Publications, New
Delhi
2. Principles of soil mechanics by Scott, Ronald F., AddisonWesley, Massachusetts .
REFERENCE BOOKS:
1. Soil Mechanics by T William Lambe and Robert V Whiteman, Wiley India
2. Soil Mechanics and Foundation Engineering by P Purushothama Raj, Pearson.
3. Geotechnical Engineering, by Venkatramaiah, C., New Age International Publishers, New
Delhi.
4. Barnes, Graham, Soil mechanics: principles and practice, Palgrave Macmillan, New York.
5. Textbook of Geotechnical Engineering, 3rd Edition by I.H. Khan, PHI Learning Private
Limited.
64
HYDROPOWER AND FLUID MACHINES (CE 223)

Name of Course Hydropower and Fluid Machines
INSTRUCTIONS:
SECTION A
Hydro Power Development: Sources of energy and their comparative study, investigations and
studies for hydropower development, estimation of available water power, flow and power
duration curves, firm power and secondary power, plant capacity, installed capacity, constraints
in hydropower development, operation and maintenance of hydropower plants. Classification of
hydropower plants based on storage characteristics, operating head, load, capacity.
SECTION B
Principal components of hydroelectric scheme. Storage and pondage, economic analysis of
storage capacity, aspects of cost allocation for different purposes, reservoir operation using flow
duration and flow mass curves. Types of power houses, various components. Reservoir
sedimentation, trap efficiency, life of a reservoir, principle of desilting, design of desilting
basins. Allignment and location of various types of intakes, trashracks, design of intake
structures. Conveyance channels and tunnels, water hammer, surge tanks, penstocks
classification and layout, hydraulic valves and gates, tail race channels.
SECTION C
IMPACT OF JET AND JET PROPULSION: Jet force on stationary plate- vertical, inclined,
curved, hinged, Jet force on vanes including curved vanes, Jet propulsion.
TURBINES: Classification, theory of impulse turbines, turbines parameters, draft tube, specific
speed, unit quantities and characteristic curves, vector diagram, governing of turbines,
cavitations, selection.
65
SECTION D
CENTRIFUGAL PUMPS: Description, classification, velocity diagram, minimum starting
speed, specific speed and characteristic curves, priming, cavitations.
RECIPROCATING PUMPS: Classification, indicator diagram, working, slip, acceleration
effect of piston, indicator diagram, air vessels.
TEXT BOOKS:
1. Modi, P. N., and Seth, S. M., Hydraulics, Fluid Mechanics and Hydraulic Machines,
Standard Book Home, New Delhi, 2005.
2. Rajput, R. K., Text Book of Fluid Mechanics and Hydraulic Machinery, S. Chand &
Company, Ltd., New Delhi, 2005.
REFERENCE BOOKS:
1. Fluid Mechanics and Machinery by C S P Ojha, R Berndtsson, and P N Chandramouli,
Oxford University Press.
2. Hydro electrical Engineering by Creager and Justin, J Wiley and Sons.
3. Water Power Engineering by H K Barrows, McGraw Hill Publishing.
66
SURVEYING - II (CE 224)

Name of Course Surveying-II
INSTRUCTIONS:
SECTION A
Curves: Types of curves, elements of curve, different methods of setting out simple circular
curves, compound curve, reverse curve, transition curve, types of transition curves, super-
elevation, suitability of a circular curve, vertical curve.
Theory of Errors: Introduction, Definitions, laws of weights, Probable errors, Most probable
value, Normal quations, method of least square, triangle, station adjustment, figure adjustment,
Quadrilateral and Polygon adjustment of closed traverse and level nets.
SECTION - B
Triangulation: Principle, classification of triangulation system, operation in triangulation
survey, reconnaisance, selection of site for base line, its measurement and extension, correction
to base line measurement, selection of stations, orders or triangulation figures, scaffolds and
signals, marking of stations, intervisibility, strength of figures, reduction to center, derivation of
relations when observations are taken from the satellite station and towards the station.
SECTION C
Trigonometrical Levelling: Introduction, determination of the level of the top of an object when
its base is accessible and not accessible, Determination of height of object when two instrument
stations are not in the same vertical plane, indirect levelling on a rough terrain, indirect levelling
on a slopes, Effect of refraction and curvature, axis signal correction, Difference in elevation in
single observation, Difference in elevations by reciprocal observation.
67
SECTION D
Photogrammetry: Basic concepts, type of photographs, Geometry of aerial photographs, scale
of a vertical aerial photograph, Relief and tilt displacement, Ground control, preparation of
mosaics, Stereoscopy, measurement of parallax and height determination, Stereoscopic plotting
instruments.
Field Astronomy: Introduction, Definitions, solution of an astronomical triangle, coordinate
systems time solar, Sidereal and standard equation of time, Conversion of time, sun dial,
determination of time, azimuth, latitude and longitude, correction for astronomical observations,
uses of astronomy in civil engineering.
TEXT BOOKS:
1. Surveying Volume I and II by B C Punmia, Lakshmi Publication
2. Surveying Volume I and II by K R Arora,
REFERENCE BOOKS:
1. Engineering Survey by W. Schofield
2. Advance Surveying by R Agor
3. Advanced Surveying by Satheesh Gopi, R Sathikumar and N Madhu by Pearson
4. Surveying, Vol. I, S.K. Duggal, Tata Mc Graw Hill Publishing Co. Ltd., New Delhi
5. Surveying and Levelling, T.P. Kanetker and Kulkarni, PuneVidyarthi Gruha Prakashan
6. Surveying for Engineers by J.Uren and W.F.Price, The Macmillan Press Ltd., London.
7. Surveying Principles and Applications by B.F.Kavanagh and D.J.G. Bird, prentice Hall,
Englewood Cliffs, New Jersey.
8. Surveying and Levelling by N. N. Basaak, Tata Mc Graw Hill Publishing Co. Ltd
68
COMMUNICATION & PROFESSIONAL SKILLS LAB-II (HS-202(P))
Course Code HS-202 (P) L-0, T-0, P-2

Semester End Max Marks: 50 Min Pass Marks: Maximum Time: 3
Examination 20 hrs
Continuous Assessment Lab work 30% Lab Record 25% Max Marks:
Viva/ Hands on 25% Attendance 20% 50
Instructions for paper setter / candidates:

(iii) Performing a practical exercises assigned by the examiner (25 marks).
(iv) Viva-voce examination (25 marks)
Note: Each practical should be performed twice for effectiveness.
List of Practicals:
1. Phonetics: Organs of speech, speech sounds, symbols, articulation of speech sounds- stress
and intonation.
2. SWOT analysis (Personal / Organisation)
3. Group discussion
4. Debate
5. Vocabulary improvement programs
6. Technical write up based on critical thinking (On subject allocated by coordinator)
7. Telephonic etiquettes: Preparing, Controlling and Follow up.
RECOMMENDED BOOKS:
1. Developing Communication Skills: by Krishan Mohan & Meera Bannerji
2. Group Discussions by Sudha Publications And Ramesh Publishing House, New Delhi
3. Vocabulary Improvement: Words Made Easy: by Diana Bonet
4. Word Power Made Easy: by Norman Lewis
69
SOIL MECHANICS LAB - CE-222(P)

Name of the Course Soil Mechanics Lab
INSTRUCTIONS:

1. Visual Soil Classification and water content determination.

2. Determination of specific gravity of soil solids.
3. Grain size analysis-sieve analysis.
4. Liquid limit and plastic limit determination.
5. Field density by:
i) Sand replacement method
ii) Core cutter method
6. Proctor`s compaction test.
7. Coefficient of permeability of soils.
8. Unconfined compressive strength test.
9. Direct shear test on granular soil sample.
10. Unconsolidated undrained(UU) triaxial shear test of fine grained soil sample.
REFERENCE BOOKS:
1. Soil Testing for Engineers by S.Prakash, PK Jain, Nem Chand & Bros.,Roorkee.
2. Engineering Soil Testing by Lambi, Wiley Eastern.
3. Engineering Properties of Soils and their Measurement by J.P.Bowles, McGraw Hill.
4. Soil Engineering in Theory and Practice, Vol.II, Geotechnical Testing and Instrumentation
Alam Singh, CBS Pub.
70
HYDRO POWER AND HYDRAULIC MACHINES LAB CE-223 (P)

Name of the Course Hydro Power And Hydraulic Machines Lab
INSTRUCTIONS:

1. Viscous flow analogy (HeleShaw apparatus) for flow net.

2. Electrical analogy for flow net.
3. Study of development of boundary layer over a flat plate.
4. Study of Magnus effect using wind tunnel
5. Study of fluid flow around a cyllinder.
6. Study of fluid flow around a sphere.
7. Study of hydraulic jump in open channel flow.
8. Specific energy studies in an open channel flow.
9. Study of flow profile over a spillway.
10. Study of sluice gates.
11. Study of characteristics of Pelton Wheel
12. Study of characteristics of Francis Turbine
13. Study of centrifugal pump test rig.
14. Study of reciprocating pump test rig.
71
SURVEYING - II CE 224(P)

Name of the Course Surveying-II Lab
INSTRUCTIONS:

1. Tachometric constant.
2. Determination of height and distance using Stadia tacheometry
3. Plane tabling by the method of radiation and intersection.
4. Solution of Three point problem in plane tabling
5. Setting out of simple circular curve by offsets from long chord and by successive bisection of
long chord.
6. Setting out of simple circular curve by radial and perpendicular offsets.
7. Setting out of simple circular curve by one theodolite and by two theodolite method.
8. Use of total station.
72
Semester-Vth
PRINCIPLES OF MANAGEMENT AND CRITICAL THINKING (HS-301)
Course Code HS-301 L - 3, T- 0, P - 2

Name of Course Principles of Management and Critical Thinking
Continue Assessment (based on sessional tests 50%) Tutorial/ MM: 50.
Assignment: 30%, Quiz/ Seminar: 10 %, Attendance: 10 %.
INSTRUCTIONS:
Course Objectives:
To understand the roles and functions of managers at various (entry, middle and the top)
levels
To explain the relationships between organizational mission, goals, and objectives
To comprehend the significance and necessity of managing stakeholders
To conceptualize how internal and external environment shape organizations and their
responses
To demonstrate empirical understanding of various organizational processes and behaviours
and the theories associated with them
To demonstrate critical thinking skills in identifying ethical, global, and diversity issues in
planning, organizing, controlling and leading functions of management
To understand organizational design and structural issues
Learning Outcomes: On completion of this course the students should be able to:
Describe the functions of management.
Outline the historical theories relating to modern management.
Explain the role of management within a business setting.
Describe human resource planning and staffing processes needed to achieve optimal
performance
Prepare a business forecast and budget.
Illustrate how business ethics and social responsibility apply to organizations.
Describe formal and informal organizational communication processes and how to influence
employees
73
SECTION A
Historical Perspectives of Management: (6 Hours)
The behavioural approach to management
The management science approach
The contingency approach
The system approach
Principles of Planning (5 Hours)
Defining planning, Purposes of planning,
Advantages and potential disadvantages of planning,
Management by objectives, Planning tools,
Strategic planning, Forecasting and budgeting
SECTION B
The Management Task (4 Hours)
The Role of management,
Defining management,
The management process, management functions,
Management goal attainment,
Management and organizational resources
Fundamentals of Organizing (5 Hours)
The definition of organizing
The organizing process
The organizing subsystem
Classical organizing theory
SECTION C
Leadership and Effective Communication (3 Hours)
Defining leadership; leader vs. manager,
Leadership behaviours, Transformational Leadership,
Coaching, Entrepreneurial leadership
Controlling for Productivity (4 Hours)
Defining production and productivity,
Quality and productivity, Operations management,
Operations control, Using control tools to control organizations
SECTION D
Managerial Ethics and Social Responsibility (6 Hours)
Fundamentals of social responsibility,
Areas of corporate social responsibility,
Social responsiveness and decision making,
Influencing individuals performing social responsibility activities,
A definition of ethics, Creating an ethical workplace
Making Good Business Decision (6 Hours)
Types of decisions, Elements of the decision situation,
74
The decision making process, Decision making conditions,
Decision making tools, Processes for making group decisions
TEXT BOOKS:
1. Charles W. L. Hill and Steven McShane (2006) Principles of Management. McGraw-
Hill/Irwin; 1st Edition. ISBN-10: 0073530123, ISBN-13: 978-0073530123
2. Moore & Parker, Critical Thinking, 9th ed. (McGraw-Hill, 2008) ISBN-13:
9780073386676
REFERENCE BOOKS:
1. Gary Dessler (2003). Management: Principles and Practices for Tomorrow's Leaders,
Prentice Hall; 3rd Edition. ISBN-10: 0131009923, ISBN-13: 978-0131009929
2. Ellen A. Benowitz (2001). Principles of Management. Cliffs Notes. ISBN-10:
076456384X, ISBN-13: 978-0764563843
3. Griffin, Ricky W., Management seventh edition, Houghton Mifflin Company
4. Fisher, Alec. The Logic of Real Arguments (Second Edition). Cambridge: Cambridge
University Press, 2004.
PRACTICAL CLASS DISCUSSION TOPICS

Some Basics: Issues, Claims, Arguments- Types & Structures, Clarity- Vagueness, Ambiguity,
Credibility, Rhetoric, & Fallacies, Formal Deductive Logic, Deductive Arguments: Truth-
Functional Logic
(a) Symbolization; (b) Truth Tables; (c) Long Truth Table Test; (d) Short Truth Table Test;
(e) Deductions w/Inference Rules; (f) Deductions w/Equivalence Rules
Left brain /right brain exercise, Truth and Knowledge, Good and Bad Reasoning, Inductive and
Deductive Reasoning, Fallacious Reasoning, Psychological Impediments to Cogent Reasoning
Truth, Belief, and the Leader/Follower Relationship.
75
STRUCTURAL ANALYSIS-II (CE-311)

Name of Course Structural Analysis-II
INSTRUCTIONS:
SECTION A
STATICALLY INDETERMINATE STRUCTURES: Force Methods Introduction to Force

Methods / Method of Consistent Deformations / Theorem of Least Work / Column Analogy
Method / Approximate Lateral Load Analysis of Building Frames / Deflections in Statically
Indeterminate Structures.
SECTION B
KINEMATICALLY INDETERMINATE STRUCTURES: Displacement Methods
Introduction to Displacement Methods / Slope Deflection Method / Moment Distribution Method
/ Kanis Method
SECTION C
INFLUENCE LINE DIAGRAM FOR INDETERMINATE STRUCTURES: Influence lines
for indeterminate beams and trusses, Muller-Breslau Principles and qualitative plot of influence
lines, influence lines for reaction, shear and bending moment in beams.
SECTION D
PLASTIC ANALYSIS: Introduction, plastic hinge concept, plastic modulus, shape factor,
upper and lower bound theorems, collapse mechanics, combined mechanics, plastics analysis of
beams and portal frames by equilibrium and mechanism methods, plastics moment distribution.
76
TEXT BOOKS:
1. Basic Structural Analysis by C.S. Reddy, Tata McGraw Hill Publishing
2. Indeterminate Structural Analysis by C .K. Wang, Tata McGraw Hill Publishing
REFERENCE BOOKS:
1. Advanced Theory of Structures by N.C. Sinha & P.K. Gayen, Dhanpat Rai and sons
2. Plastic methods of Structural Analysis by B.G. Neal, Chapman and Hall
3. Theory of Structures by B.C.Punmia, Ashok Jain, Arun Jain, Standard Publishers
4. Yuan Yu Hsieh, Elementry Theory of Structures, Prentice Hall
5. Ghali, A., Neville, A. M., Structural Analysis (Unified Classical and Matrix Approach) ,
Chapman and Hall Ltd.
6. Menon Devdas, Structural Analysis Narosa Publishing House
7. Menon, Devdas, Structural Analysis, Narosa Publishing House
8. Menon, Devdas, Advanced Structural Analysis, Narosa Publishing House, New Delhi.
9. R. C. Hibbeller, Structural Analysis, Pearson Education.
10. J. McCarmac and R.E.Elling, Structural Analysis: A classical and Matrix A approach,
Harper and Row Publishers
11. Kinney, J.S., Indeterminate Structural Analysis ,Oxford IBH Publishing Company.
77
DESIGN OF CONCRETE STRUCTURES (CE-312)

Name of Course Design of Concrete Structures
INSTRUCTIONS:
SECTION A
Introduction: Properties of concrete and reinforcing steel, design philosophies, limit state,
ultimate load method, working stress method. Design loads, Load Combinations,
Limit state method: Design of Beams: Singly reinforced, doubly reinforced, rectangular, T and
L beams and lintels.
SECTION - B
Design of Slabs: One way and two way slabs
Design of Stair Cases: Types terms used, design of stairs spanning, horizontally, doglegged
stairs with quarter space landing, stairs with central stringer beam.
SECTION - C
Design of Columns: Subjected to eccentric and axial loading, Using S.P. 16.
Design of footings: Individual and combined footing and raft foundation.
SECTION - C
Design of retaining walls: Various types of retaining walls, design of cantilever and counterfort
retaining walls.
TEXT BOOKS:
1. Pillai,S. Unnikrishna, Menon,Devdas: Reinforced Concrete Design, Tata McGraw-Hill,
New Delhi
2. Varghese, P. C.: Limit state design of reinforced concrete, PrenticeHall, New Delhi
REFERENCE BOOKS:
1. Gambhir, M. L.: Fundamentals of reinforced concrete design, PrenticeHall, New Delhi.
2. Bhavikatti, S. S.: Design of R.C.C. structural elements, New Age International
Publishers, New Delhi.
3. A K Jain: Reinforced Concrete (Limit state design).
4. B. C. Punmia: Reinforced Concrete Structures, Luxmi Publications
5. IS 456 2000: Code of Practice for Plain and Reinforced Concrete
6. Limit State Design of Reinforced Concrete, 2nd Edition by Varghese, PHI Learning
Private Limited.
78
GEOTECHNICAL ENGINEERING-II (CE-313)

Name of Course Geotechnical Engineering-II
INSTRUCTIONS:
SECTION A
EARTH PRESSURE: Different types of earth pressures, states of plastic equilibrium Rankines
theory and Coulombs theory, influence water table, surcharge, wall friction and deformation on
the earth pressure, application of Rankines and Coulombs theory to cohesionless and cohesive
spoils, Coulombs graphical method, stability considerations for retaining walls, effect or
earthquakes. Design of retaining walls.
STABILITY OF SLOPES: Stability of finite and infinite slopes, types of failures, different
factors of safety, determination of factor of safety by method of slices, Swedish circle, friction
circle, Bishops method, Mo. Gangstern- price method, Tylors stability number, location of
critical circle, stability analysis of earth dam slopes for different conditions. Design of filters and
rock toe.
SECTION B
SHEET PLIES: Different types of sheet pile walls-free and fixed earth support anchored bulk
heads, design principles, arching in tunnels, open cut strutting and sheeting.
FOUNDATIONS: Different types of loads coming on foundations, types of shallow shallow

and deep foundations, footing-rafts-piles-wells-selection of foundation type-dewatering of
foundations-type of explorations, methods of boring, soil samples and samplers.
SECTION C
SHALLOW FOUNDATIONS: Definition, bearing capacity, factors affecting, Terzaghis
theory of bearing capacity, effect of size, shape of ground water table, determination of bearing
capacity from building codes, plate load test, penetration test, static and dynamic cone tests,
housels approach, bearing capacity of sands and clays, settlements of foundation. Elastic
settlements, consolidation settlements, differential settlements-permissible settlements, design
79
principles of depth of foundation, spread footing, combined footing, raft foundations, principles
of floating frats, foundations on non-uniform soils.
DEEP FOUNDATION: Types of piles based on function, materials and methods of

construction, friction and end bearing piles, static formulae-ENR and Hillarys formula-group
action in piles, block failures, settlement of pile groups in sands and clays pile load test negative
skin friction, under reamed piles.
SECTION D
WELL FOUNDATION: Elements, forces acting on well, lateral stability analysis, problems in
sinking of wells and remedial measures.
MACHINE FOUNDATIONS: model study, natural frequency of block foundation system,

block foundation under vertical vibration.
REINFORCED EARTH: Introduction, analysis and design of reinforced earth wall, reinforced
earth base.
TEXT BOOKS:
1. Soil Mechanics and Foundation Engineering by P. Purushothama Raj, Wiley India.
2. Principles of Foundation Engineering: B. M. Das, PWS Publishing Co. .
REFERENCES BOOKS:
1. Advanced Foundation Engineering: Murthy, VNS, CBS Publishers .
2. Analysis and Design of Foundation and Retaining Structures: S. Parkash & Gopal Ranjan,
Sarita Prakashan Meerut.
3. Foundation Engineering: P. C. Verghese, Prentice Hall of India .
4. Theory and practice of Foundation Design: N. N. Som and S. C. Das, Prentice Hall of India
5. Foundation Engineering Handbook: H. Y. Fang, CBS Publishers.
6. Soil Engineering Theory & Practice: Alam Singh, CBS Publishers.
80
HYDROLOGY AND GROUNDWATER (CE-314)

Name of Course Hydrology and Groundwater
INSTRUCTIONS:
SECTION A
INTRODUCTION: Scope and application of hydrology, hydrologic cycle, water budget, role of
water in national development, assessment of water resources of the country, single purpose and
multipurpose projects, cost benefit analysis.
HYDROLOGICAL PROCESSES: Precipitation, form and types of precipitation, precipitation

measurement, gauge networks, hyetographs, adjustment of data, filling in missing data, average
rainfall by- arithmetic mean, thissen polygon and isohytal methods, mass curve, and depth- area-
duration curve, PMP.
SECTION B
WATER ABSTRACTIONS: Evaporation, transpiration, evapo-transpiration and their
estimation, methods of controlling evaporation, interception, infiltration, factors affecting
infiltration, infiltration, infiltrometers, infiltration indices.
RUNOFF: Overland flow and runoff, factors affecting runoff, rainfall-runoff relationship,
estimation of runoff.
SECTION C
HYDROGRAPHS: Hydrographs, base flow separation, unit hydrograph- its derivation and
application, hydrograph from a complex storm, U.H. for other different duration, limitation of
U.H. synthetic U.H.
FLOODS: Estimation of peak flood by empirical formulas and U.H., flood frequency studies
using Gumbels method, flood routing using Muskingum method & Modified puls method.
81
SECTION D
GROUND WATER OCCURANCE AND QUALITY: introduction to ground water, water

bearing formations, aquifers, aquicludes and aquitards, confined and unconfined and leaky
aquifers, ground water origin, modes of occurrence, yield of water and water quality.
WELL HYDRAULICS: Definition of terms, governing flow, equilibrium and non-equilibrium

well equations, effect of hydro-geologic conditions on draw down, draw down from pumping
tests, well interference and well efficiency, radius of influence, recharge and boundary
conditions, effect of partial penetration, thesis equation.
TEXT BOOKS:
1. Groundwater Hydrology by Todd . D.K., John Wiley and Sons, New York.
2. Ground water by Raghunath, H.M., New Age International (p) Ltd.
REFERENCE BOOKS:
1. Elementary Engineering Hydrology, M J Deodhar, Pearson Education
2. Water Resources Engineering by Linsley, Kohler and Phallus, Cambridge Press
3. Hydraulics of Groundwater by Jacob Bear , McGraw Hill, 1979.
4. Groundwater Resources Evaluation by Walton W.C., McGraw Hill Book Co., New York.
5. Groundwater Engineering Abdel, Aziz Ismail Kashef, McGraw Hill Book Co., New York.
6. Applied Hydrology by K.N. Mutreja, Tata Mcgraw Hill Publishing Co.
7. Ground water Engineering : K.R. Karanth
8. Engineering Hydrology by Ojha, Berdtteson and Bhuniya, Oxford University Press.
9. Ground Water Hydrology, Agarwal, PHI Learning Private Limited.
82
TRANSPORTATION ENGINEERING-I (CE-315)

Name of Course Transportation Engineering-I
INSTRUCTIONS:
SECTION A
ROAD DEVELOPMENT AND PLANNING: Brief history of road development, road cross
section, necessity of transportation planning, classification of roads, road patterns, planning
surveys, saturation system, highway planning in India, road development plans.
HIGHWAY LOCATION AND ALIGNMENT: Basic requirements of an ideal alignment and
factors controlling, engineering survey for highway location, drawing and reports, highway
projects.
SECTION - B
HIGHWAY GEOMETRIC DESIGN: Highway cross section elements, sight distances, design of
horizontal and vertical alignment.
TRAFFIC ENGINEERING: Traffic characteristics, traffic studies and their uses, traffic control
devices, intersection, goods passenger terminals, traffic planning and administration.
SECTION C
PAVEMENTS DESIGN: Design factors, design of flexible pavements, CBR, gI and Burmister
methods, design of rigid pavements.
PAVEMENT MATERIALS: Soils aggregates and their characteristics, bituminous materials and
mixtures, Portland cement concrete.
SECTION D
CONSTRUCTION OF ROADS: Construction of water bound macadam roads, bitumineous
pavements, cement concrete pavements, design and construction joints in cement concrete
pavements.
HILL ROADS: General considerations, alignment, geometric design and construction, drainage
and maintenance problems in hill roads.
83
HIGHWAYS MAINTENANCE: Pavement failures, maintenance of highway pavement,
evaluation and strengthening of existing pavements.
TEXT BOOKS:
1. Highway Engineering by Khanna S.K. & Justo C. E. G., Nem Chand and Brothers.
2. Traffic Engineering & Transport Planning by Kadiyali L.R., , Khanna Publishers.
REFERENCE BOOKS:
1. Principles of Highway Engineering and Traffic Analysis, Fred L. Mannering and Walter. P.
Kilareski, Wiley.
2. Highway Engineering, Wright and Dixen, Wiley Inda
3. Fundamentals of Transportation and Traffic Operations, Pergamon, Elsevier Science Inc.,
New York.
4. Highway Vol. I & II by O. Flaherty C.A., Edward Arnold
5. Highway Traffic Analysis and Design, 3rd Edition, R.J. Salter and N.B. Hounsell, Macmillan
6. Highway and Transportation Engineering and Planning, G. Macpherson, Longman Scientific
and Technical
7. Highway Engineering, M. Rogers, Blackwell Publishing
84
STRUCTURAL ANALYSIS LABORATORY CE 311 (P)

Name of Course Structural Analysis Laboratory
INSTRUCTIONS:

1. To Verify the Bettis Law.

2. Study of a three hinged arch experimentally for a given set of loading and to compare the
results with those obtained analytically.
3. To obtain experimentally the influence line diagram for horizontal thrust in a three hinged
arch and to compare the same with the theoretical value.
4. To determine the flexural rigidity of a given beam.
5. To study the behavior of different type of struts.
6. To verify moment area theorem for slopes and deflections of a beams
7. To find the deflection of a pin-connected truss and to verify the results by calculation and
graphically.
8. To determine the carry over factors for beam with rigid connections.
9. To determine the rotational stiffness of a beam when far end is (a) fixed (b) pinned.
10. Determine experimentally the horizontal displacement of the roller end of a two hinged arch
for a given set of loading and to compare the results with those obtained analytically.
11. To obtain experimentally the influence line diagram for horizontal thrust in a two hinged arch
and to compare the same with the theoretical value.
85
CE-312 (P): CONCRETE LABORATORY
Course Code CE-312(P) L-0, T-0,P-2

Name of Course Concrete Laboratory
Semester End Examination MM: 25 Min. Marks : 10
Continuous Assessment Lab work 30%, Lab record 25%, Viva 25%, Max. Marks : 25
Attendance 20%
INSTRUCTIONS:
(ii) Viva-voce examination.

Vive-voce examination will be related to the practicals listed below and to be performed
by the students during the semester.
LIST OF EXPERIMENTS
Sr. Title of the Experiment

No.
A. Cement:
1 To determine the compressive strength of cement mortar using 50 mm cube specimens.
2 To determine the tensile strength of cement mortars using Briquette specimens.
B. Fine and Coarse Aggregate:
3 To determine the fineness modulus of fine aggregate.
4 To determine the fineness modulus of coarse aggregate.
5 To determine the Flankiness and Elongation indices of coarse aggregate sample.
C. Concrete:
6 To determine the workability of concrete by slump test.
7 To determine the workability of concrete by compaction factor test.
8 To determine the compressive strength of concrete by cube test.
9 To determine the split tensile strength of concrete of given mix properties.
10 To determine the concrete compressive strength using rebound hammer.
11 To determine the pulse velocity of propagation of compression waves in concrete.
12 To determine the yongs modulus of elasticity of moulded concrete cylinders under
longitudinal compressive stress.
13 To design concrete mix using I S method.
86
Semester VI
Open Elective
ENERGY ASSESSMENT AND AUDITING - EE-300
Course Code EE-300 L - 3, T- 0, P 0
Name of Course Energy Assessment and Auditing
Lectures to be delivered 39 (L-39 for each semester)
INSTRUCTIONS:
SECTION A
Energy Scenario: Commercial and Non-commercial energy, primary energy resources,
commercial energy production, final energy consumption, energy needs of growing economy,
long term energy scenario, energy pricing, energy sector reforms, energy and environment,
energy security, energy conservation and its importance, re-structuring of the energy supply
sector, energy strategy for the future, air pollution, climate change. Energy Conservation Act-
2001 and its features.
Basics of Energy and its various forms: Electricity basics- DC & AC currents, electricity tariff,
load management and maximum demand control, power factor improvement, selection &
location of capacitors, Thermal Basics-fuels, thermal energy contents of fuel, temperature &
pressure, heat capacity, sensible and latent heat, evaporation, condensation, steam, moist air and
humidity & heat transfer, units and conversion.
SECTION B
Energy Management & Audit: Definition, energy audit, need, types of energy audit. Energy
management (audit) approach-understanding energy costs, bench marking, energy performance,
matching energy use to requirement, maximizing system efficiencies, optimizing the input
energy requirements, fuel & energy substitution, energy audit instruments.
Material and Energy balance: Facility as an energy system, methods for preparing process
flow, material and energy balance diagrams.
SECTION C
Energy Action Planning: Key elements, force field analysis, Energy policy purpose,
perspective, contents, formulation, ratification, Organizing - location of energy management, top
management support, managerial function, roles and responsibilities of energy manager,
87
accountability. Motivating-motivation of employees: Information system-designing barriers,
strategies; Marketing and communicating-training and planning.
Financial Management: Investment-need, appraisal and criteria, financial analysis techniques-
simple pay back period, return on investment, net present value, internal rate of return, cash
flows, risk and sensitivity analysis; financing options, energy performance contracts and role of
ESCOs.
SECTION D
Project Management: Definition and scope of project, technical design, financing, contracting,
implementation and performance monitoring. Implementation plan for top management,
Planning Budget, Procurement Procedures, Construction, Measurement & Verification.
Energy Monitoring, Targeting and Global environmental concerns: Defining monitoring &
targeting, elements of monitoring & targeting, data and information-analysis, techniques -energy
consumption, production, cumulative sum of differences (CUSUM). United Nations Framework
Convention on Climate Change (UNFCC), sustainable development, Kyoto Protocol, Conference
of Parties (COP), Clean Development Mechanism (CDM), Prototype Carbon fund (PCF).
TEXT BOOKS:
1. L.C. Witte, P.S. Schmidt, D.R. Brown, Industrial Energy Management and Utilisation
Hemisphere Publ, Washington, 1988.
2. O. Callaghn, P.W. Design and Management for Energy Conservation, Pergamon Press,
Oxford.
REFERENCE BOOKS:
1. I.G.C. Dryden, The Efficient Use of Energy Butterworths, London.
2. W.C. turner, Energy Management Hand book Wiley, New York.
3. W.R. Murphy and G. Mc KAY Energy Management Butterworths, London.
4. Handbook of Energy Audits by Albert Thuman Fairman Press Inc.
5. Energy basis for man and nature by Howard T.Odum & Elisbeth. C. Odum.
88
TOTAL QUALITY MANAGEMENT - ME-300
Course Code ME-300 L - 3, T- 0, P 0

Name of Course Total Quality Management
INSTRUCTIONS:
SECTION A
Introduction - Need for quality - Evolution of quality - Definition of quality - Dimensions of
manufacturing and service quality - Basic concepts of TQM - Definition of TQM TQM
Framework - Contributions of Deming, Juran and Crosby Barriers to TQM.
Quality Control and Improvement Tools: Check Sheet, Histogram, Pareto Chart, Cause and
Effect diagram, Scatter diagram, Control chart, Graph, Affinity diagram, Tree diagram, Matrix
diagram, Process decision program chart, Arrow diagram, Acceptance Sampling, Process
capability studies, Zero defect program (POKA-YOKE).
SECTION B
TQM PRINCIPLES: Leadership Strategic quality planning, Quality statements - Customer
focus Customer orientation, Customer satisfaction, Customer complaints, Customer retention -
Employee involvement Motivation, Empowerment, Team and Teamwork, Recognition and
Reward, Performance appraisal Continuous process improvement PDSA cycle, 5s, Kaizen -
Supplier partnership Partnering, Supplier selection, Supplier Rating.
SECTION C
TQM TOOLS & TECHNIQUES: The seven traditional tools of quality New management
tools Six-sigma: Concepts, methodology, applications to manufacturing, service sector
including IT Bench marking Reason to bench mark, Bench marking process FMEA
Stages, Types. Quality circles Quality Function Deployment (QFD) Taguchi quality loss
function TPM Concepts, improvement needs Cost of Quality Performance measures.
SECTION D
Quality Management System & Quality Audit: Quality Systems, Quality management
principles, ISO-9000:2000, ISO 9001 : 2000, ISO 14000, Future of quality system audit, Audit
89
objectives, types of quality audit, Quality Auditor, Audit performance. Case studies of TQM
implementation in manufacturing and service sectors including IT.
TEXT BOOKS:
1. Dale H. Besterfiled, et at., Total Quality Management, Pearson Education Asia, 3rd Edition,
Indian Reprint.
2. Ross, J.E.: Total Quality Management, Vanity Books International.
REFERENCE BOOKS:
1. James R. Evans and William M. Lindsay, The Management and Control of Quality, South-
Western (Thomson Learning).
2. Oakland, J.S., TQM Text with Cases, Butterworth Heinemann Ltd., Oxford.
3. Suganthi,L and Anand Samuel, Total Quality Management, Prentice Hall (India)Pvt. Ltd.
4. Janakiraman, B and Gopal, R.K, Total Quality Management Text and Cases, Prentice
Hall (India) Pvt. Ltd.
5. Goetsch, D.L. & Davis,S. : Introduction to Total Quality, Prentice Hall.
6. Juran, J.M. & Gryna, F.M. : Quality Planning and Analysis, Tata McGraw Hill Publishing
Co. Ltd., New Delhi
7. Charantimath, P.M. : Total Quality Management, Pearson Education.
90
OPTIMIZATION METHODS FOR ENGINEERING SYSTEMS - NS-300
Course Code NS-300 L - 3, T- 0, P 0

Name of Course Optimization Methods For Engineering Systems
INSTRUCTIONS:
SECTION A
Introduction: Engineering Application; Statement of the Optimal Problem; Classification;
Optimization Techniques;
Classical Method: Single Variable Optimization; Multivariable Optimization Without any
Constraints with Equality and Inequality Constraints.
SECTION B
One-Dimensional Minimization Method: Unimodal Function; Elimination Method
Dichotomous Search, Fibonocci and Golden Method; Interpolation Method Quadratic and
Cubic Interpolation Method.
Unconstrained Minimization Method: Univariate, Conjugate Directions, Gradient And
Variable Metric Method.
SECTION C
Constrained Minimization Method: Characteristics of a constrained problem; Direct Method
of feasible directions; Indirect Method of interior and exterior penalty functions.
Geometric Programming: Formulation and Solutions of Unconstrained and Constrained
geometric programming problem.
SECTION D
Dynamic Programming: Concept of Sub-optimization and the principal of optimality: Calculus,
Tabular and Computational Method in Dynamic Programming: An Introduction to Continuous
Dynamic Programming.
Integer Programming: Gomorys Cutting Plane Method for Integer Linear Programming;
Formulation & Solution of Integer Polynomial and Non- Linear problems.
91
TEXT BOOKS:
1. Optimization (Theory & Application)- S.S. Rao, Wiley Eastern Ltd, New Delhi.
2. Optimization Concepts and Applications in Engineering Ashok D.Belegundu and Tirupathi
R Chandrupatla Pearson Education 1999, First India Reprint 2002.
REFERENCE BOOKS:
1. Optimization: Theory and Practice, C.S.G. Beveridge and R.S. Schechter, McGraw Hill, New
York.
2. Kalyanamoy Deb, Optimization for Engineering design algorithms and Examples, Prentice
Hall of India Pvt. Ltd. 2006.
3. Rao, Singaresu, S., Engineering Optimization Theory & Practice, New Age International
(P) Limited, New Delhi, 2000.
4. Johnson Ray, C., Optimum design of mechanical elements, Wiley, John & Sons, 1990.
5. Goldberg, D.E., Genetic algorithms in search, optimization and machine, Barnen, Addison-
Wesley, New York, 1989.
92
REMOTE SENSING AND GIS- CE-300
Course Code CE-300 L - 3, T- 0, P 0

Name of Course Remote Sensing and GIS
INSTRUCTIONS:
SECTION A
EMR AND ITS INTERACTION WITH ATMOSPHERE & EARTH MATERIAL: Definition of
remote sensing and its components Electromagnetic spectrum wavelength regions important
to remote sensing Wave theory, Particle theory, Stefan-Boltzman and Weins Displacement
Law Atmospheric scattering, absorption Atmospheric windows spectral signature concepts
typical spectral reflective characteristics of water, vegetation and soil.
PLATFORMS AND SENSORS: Types of platforms orbit types, Sun-synchronous and
Geosynchronous Passive and Active sensors resolution concept Pay load description of
important Earth Resources and Meteorological satellites Airborne and spaceborne TIR and
microwave sensors.
SECTION B
IMAGE INTERPRETATION AND ANALYSIS: Types of Data Products types of image
interpretation basic elements of image interpretation - visual interpretation keys Digital
Image Processing Pre-processing image enhancement techniques multispectral image
Classification Supervised and unsupervised.
SECTION C
GEOGRAPHIC INFORMATION SYSTEM: Introduction Maps Definitions Map
Projections types of map projections map analysis GIS definition basic components of
GIS standard GIS softwares Data type Spatial and non-spatial (attribute) data
measurement scales Data Base Management Systems (DBMS).
93
SECTION D
DATA ENTRY, STORAGE AND ANALYSIS: Data models vector and raster data data
compression data input by digitization and scanning attribute data analysis integrated data
Analysis Modeling in GIS Highway alignment studies Land Information System.
TEXT BOOKS:
1. Lillesand, T.M., Kiefer, R.W. and J.W. Chipman. (2004). Remote Sensing and Image
Interpretation. V Edn. John Willey and Sons (Asia) Pvt. Ltd., New Delhi.
2. Anji Reddy, M. (2001). Textbook of Remote Sensing and Geographical Information System.
Second edn. BS Publications, Hyderabad.
REFERENCE BOOKS:
1. Lo. C.P. and A.K.W. Yeung (2002). Concepts and Techniques of Geographic Information
Systems. Prentice-Hall of India Pvt. Ltd., New Delhi.
2. Peter A. Burrough, Rachael A. McDonnell (2000), Principles of GIS. Oxford University
Press.
3. Ian Heywood (2000), An Introduction to GIS, Pearson Education Asia.
94
OPERATING SYSTEMS- CS-300
Course Code CS-300 L - 3, T- 0, P 0

Name of Course Operating Systems
INSTRUCTIONS:
SECTION A
Introduction to System Software: Overview of all system softwares: Compiler, Assembler,
Linker, Loader, Operating system, I/O manager
Fundamentals of Operating System: OS services and Components, Multitasking,
Multiprogramming, Multiprocessing, Time Sharing, Buffering, Spooling, Distributed OS
SECTION B
Process and Thread Management: Concept of process and threads, Process states, Process
management, Context switching, Interaction between processes and OS Multithreading
Example OS : Linux
Concurrency Control: Concurrency and Race Conditions, Mutual exclusion requirements,
Software and hardware solutions, Semaphores, Monitors, Classical IPC problems and solutions,
Deadlock, Characterization, Detection, Recovery, Avoidance and Prevention
SECTION C
Memory Management: Memory partitioning, Swapping, Paging, Segmentation, Virtual,
memory, Overlays, Demand paging, Performance of Demand paging, Virtual memory concepts,
Page replacement algorithms, Allocation algorithms, Example OS : Linux
I/O Systems: Secondary-Storage Structure, Disk structure, Disk scheduling, Disk management,
Swap-space management, Disk reliability, Stable storage implementation, Introduction to clock,
Clock hardware, Clock software
SECTION D
File systems: File concept, File support, Access methods, Allocation methods, Directory
Systems, File protection, Free space management, Example OS : Linux
Protection & Security: Protection, Goals of protection, Domain of protection, Access matrix,
Implementation of access matrix, Revocation of access rights, Security, The security problem,
Authentication, One-Time passwords, Threats, Example OS: Linux Case Study: Android OS
95
TEXT BOOKS:
1. Operating System Concepts by Silberschatz and Galvin, Wiley.
2. Operating Systems Achyut S. Godbole Tata McGraw Hill
REFERENCE BOOKS:
1. Operating Systems Internals and Design Principles, by William Stallings, Prentice Hall.
2. Modern Operating Systems by Andrew S Tanenbaum, Prentice Hall India.
3. Operating Systems by Gary Nutt, Nabendu Chaki, Sarmishtha Neogy, Pearson
4. Operating Systems Design & Implementation Andrew S. Tanenbam, Albert S. Woodhull
Pearson
5. Operating Systems D. M. Dhardhere Tata McGraw Hill
96
BRIDGE ENGINEERING (CE-321)
Name of Course Bridge Engineering
INSTRUCTIONS:
SECTION A
Introduction: Definitions, components of a bridge, classification, importance and standard
specifications.
Investigation for bridge: Site selection, data drawing, design discharge linear water way,
economical span, location of piers and abutments, vertical clearance above HFL, scour depth.
Traffic projection, investigation report choice of bridge type.
SECTION B
Standard specification for Road Bridge: IRC bridge code, determination of dead loads and live
loads, wind loads, longitudinal forces, centrifugal forces, horizontal forces due to water current
buoyancy effect, earth pressure, temperature effect, deformation stresses, Secondary
stresses, erection stresses, seismic forces.
Culverts: Design of slab culvert and box culvert.
SECTION C
Design of Tbeam reinforced concrete bridges.
SECTION D
Hydraulic & Structural Design of Piers, abutments, wing-wall and approaches.
Brief Description of Bearings, joints, articulation and other details.
Bridge Foundation Design: Various types, necessary investigations and design criteria of well
foundation.
TEXTBOOKS:
1. Essentials of Bridge Engineering, D. J. Victor, Oxford & IBH Pub. N. Delhi.
2. Design of concrete bridge : Aswani, Vazirani, Ratwani, Khanna Publishers.
REFERENCE BOOKS
1. Bridge Engineering by S. Ponnuswamy , McGraw Hill Publication.
2. Design of Bridges by N. Krishna Raju, Oxford & IBH, N. Delhi.
3. Bridge Deck Analysis by R. P. Pama & A. R. Cusens, John Wiley & Sons.
4. Design of Bridge Structures by T. R. Jagadish & M. A. Jairam, Prentice Hall of India, N.
Delhi.
97
IRRIGATION ENGINEERING (CE-322)
Name of Course Irrigation Engineering
INSTRUCTIONS:
SECTION A
INTRODUCTION: Definition, function, advantages and disadvantages, irrigation development
in India. Water Resources of Globe; Multi purposes use of water.
TYPES OF IRRIGATION SYSTEMS: Lift, flow and tank irrigation, various methods of
applying water to crops- Border, strip, check basin and furrow methods, sprinkler and drip
irrigation methods, comparative study and efficiency of these methods.
SECTION B
WATER QUALITY AND REQUIREMENT OF CROPS: Main crops of India and their seasons,
water requirement and different ages of crop growth, critical periods, delta, duty and base period,
relation between them, factors effecting duty, Kor depth, Kor period, crop rotation, Paleo
irrigation and irrigation efficiencies. Consumptive use, estimation and factors affecting
consu8mptive use.
LIFT AND LAND IRRIGATION: Open wells and tube wells, types of tube wells, irrigation
from wells, ground water field and well hydraulics.
AGRONOMICAL ASPECTS OF IRRIGATION: Soil water crop relationship, estimation of
depth and frequency of irrigation, use of saline water for irrigation, effect of saline irrigation on
crop growth, crop yield and soil fertility.
SECTION C
CANAL IRRIGATION: Types of canals, parts of canal irrigation systems, canal alignment,
determination of channel capacity and storage capacity, assessment of water requirement,
estimation canal losses, design of canals, regime and semi theoretical approaches.
WATER LOGGING AND DRAINAGE: Causes, preventive and curative measures, drainage of
irrigated lands, open and tile drainage system, saline and alkaline lands and their reclamation,
types of channel lining and design of lined channels.
98
SECTION D
CANAL MANAGEMENT: Requirement of irrigation outlets, classification, definitions,
selection of type of outlet, design aspects, flexibility and sensitivity of outlets, assessment canal
revenue.
RIVER ENGINEERING: Introduction, classification of river stages, methods of river training,
guide banks and their design, marginal embankments, islands, stills and dykes.
TEXTBOOKS:
1. Irrigation Engineering, N N Basak, , McGraw Hill Publication.
2. Elementary Irrigation Engineering, G L Asawa, New Age International.
REFERENCE BOOKS
1. Irrigation Engineering & Hydraulic Structures by S.R. Sahasrabudhe, S K Kataria &
Sons-New Delhi
2. Irrigation Engineering & Hydraulic Structures by S.K. Garg
3. Fundamentals of Irrigation Engineering by Bharat Singh, Nem Chand Bros. Roorkee
4. Irrigation Water Management (Principles & Practices) by Dilip Kumar Majumdar,
Prentice Hall of India (P), Ltd.
99
TRANSPORTATION ENGINEERING-II (CE-324)

Name of Course Transportation Engineering
INSTRUCTIONS:
SECTION A
URBAN TRANSPORTATION PLANNING: Introduction, Transportation system
management, Transportation plan, Travel forecasting, Trip generation models Multiple linear
regression analysis, Category analysis, Trip Distribution Fratar method, Gravity model, Mode
usage Trip interchange mode choice models, Trip assignment- Minimum path techniques.
SECTION B
AIRPORTS: INTRODUCTION: Brief history of air navigation, role of civil engineering, brief
history of ICAO
AIRCRAFT CHARACTERISTICS: Size, capacity, range speed and their Trends, components of
aircrafts, weight turning radios and wheel load configurations.
AIRPORT PLANNING: Regional planning, topographical features, population, existing air port
in the vicinity, air traffic characteristics, development of new airports, airport site selection and
factors effecting it.
AIRPORT OBSTRUCTIONS: Zoning, classification of obstructions, imaginary surfaces,
approach zone and turning zones.
AIRPORT LAYOUT: Runway design, airport capacity and configuration, loading apron, service
hanger, taxiway design, terminal area.
MISCELLANEOUS: Airport marking and lightings, drainage systems, airport pavement design.
SECTION C
RAILWAYS: Railway track developments, component parts, gauges, wheel and axle
arrangements, resistances to traction and stresses in track, various resistances and their
evaluation, hauling capacity and tractive effort, stress in rail, sleepers, ballast and foundation.
100
TRACK COMPONENTS: Permanent way, component parts, coning of whelks, rails, creep, wear
failure, joints, sleepers- requirement types, rail fittings and fixtures, ballast requirements,
drainage, ballastless track, sub grade and embankments.
GEOMETRIC DESIGN: Track alignment, horizontal curves super elevation, equilibrium cant
and cant deficiency, transition curves, vertical curves gradients and grade compensation,
widening of gauge on curves.
POINTS AND CROSSINGS: Design of simple turn out, various types of track junctions.
SIGNALLING AND INTERLOCKING; Principles and classification of signals, control of
movement of trains, track circuitry, fuctions and methods of interlocking, track drainage and
maintenance.
SECTION D
TUNNELING: Necessity, shape, size, alignment, shafts, pilot tunnel, tunneling through soft
ground, through rocks, drilling, safety measures, ventilation, lightening, drainage and tunneling
machinery.
TEXTBOOKS:
1. A textbook of Railway Engineering by Saxena & Arora.
2. Railway Engineering by Satish Chandra and M M Agarwal, Oxford University Press.
REFERENCE BOOKS
1. Irrigation Engineering & Hydraulic Structures by S.R. Sahasrabudhe, S K Kataria &
Sons.
2. Airport planning and design by Khanna, Arora & Jain, Nem Chand Publishers
3. Airport Engineering by S. C. Rangwala, Charotar Publishing Co.
4. Planning and design of airports, by Robert Horenjeff & Francis X McKelvy, Mc Graw
Hill.
5. Indian Railway tracks by Agarwal M.M.
6. Transportation Engineering by Vazirani and Chandola, S.P., Khanna Publishers.
7. Transportation Engineering by K. P. Subramaniam, SCITECH Publishers.
101
WATER SUPPLY AND SYSTEM ENGINEERING (CE-350)

Name of Course Water Supply and System Engineering
INSTRUCTIONS:
SECTION A
WATER ENVIRONMENT: Environment, water resources of hydrosphere, different water
pollutants and their impacts on human beings, sources of supply, yield, design of intakes,
estimation of demand, design period.
WATER/ WASTEWATER CHARACTERISTICS: Water quality criteria and standards for
potable and industrial uses, control of waterborne diseases. Physical, chemical, and biological
characteristics of domestic and industrial wastewaters, significance of pollutant parameters and
effluent discharge standards.
SECTION B
TREATMENT OBJECTIVES AND METHODS: Unit operations and processes and selection of
treatment mode and sequence
Primary treatment screening, neutralization, equalization, flocculation, sedimentation,
floatation, stripping.
Secondary treatment - suspended and attached biological growth systems for aerobic, anaerobic,
and anoxic processes, lagoons and stabilization ponds.
Tertiary treatment Oxidation/ reduction, precipitation, adsorption, ion exchange and membrane
(RO/UF) processes, disinfection.
Wastewater/ sludge disposal self-purification, oxygen sag analysis, land treatment Sludge
Treatment, dewatering, conditioning, digestion.
SECTION C
CONVEYANCE/ DISTRIBUTION SYSTEMS: Conductors different pipe systems, design
considerations, laying, testing and effects of pipe corrosion and its preventive measures.
Sewers Hydraulic design, construction and appurtenances, operation and maintenance.
102
Pumps and pumping necessity, types of pumps, characteristics curves, selection criteria,
economical diameter of pumping/ transmission main, problems in sewage pumping.
Distribution network methods, layout, storage, and distribution reservoir, analysis of
distribution systems.
SECTION D
PLUMBING SYSTEMS: General principles, materials for service pipe, service connection,
water meters, valves. Principles of house drainage, pipes, traps, sanitary fittings, systems of
plumbing, house drainage plans.
RURAL AND SEMI-URBAN SANITATION: Collection and disposal of dry refuse, sullage,
excretal waste, night soil disposal without water carriage, PRAI latrines, chemical toilets, pre-
cast units for low cost sanitation
TEXTBOOKS:
1. Elements of Water Supply and Wastewater by G.M. Fair, G.C. Geyer, D.A. Okun, New
Age International Publishers.
2. Environmental Engineering (Vol I &II) by B.C. Punmia and A. Jain, Laxmi Publications
REFERENCE BOOKS:
1. Wastewater Engineering Treatment and Reuse, Metcalf & Eddy Inc.
2. Environmental Engineering (Vol I&II) by P.N.Modi, Standard Book House.
3. CPHEEO (Ministry of Urban Development, New Delhi). Manual on
i. Water Supply and Treatment
ii. Sewerage and Sewage Treatment
4. Water Supply & Sewerage by McGhee, T. J., McGraw Hill International Edition, New
Delhi.
5. Environmental Engineering by H. S. Peavy, D. R. Row and G. Tchobanoglous, McGraw
Hill International Edition.
103
ESTIMATION AND COSTING (CE-326)

Name of Course Estimation and Costing
INSTRUCTIONS:
SECTION A
ESTIMATING: Different types of estimates, methods of taking out and scheduling quantities for
the following works. Building, culverts, bridges, irrigation works, steel structures, road works,
canal works, sanitary and water supply works, roofs, R.C.C. work, Deductions for openings.
ANALYSIS OF RATES: Scheduling of rates, analysis of rates, problem in analysis of rates of
the following items: earth work, brick masonry, stone masonry, cement concrete, RCC work,
iron work, plastering, flooring, white washing, painting, wood work, Road work .
SECTION - B
SPECIFICATIONS: Object of specifications, general specifications, detailed specifications of
the following: earth work in foundation, lean concrete in foundation, lime concrete in roof
terracing, cement concrete, RCC, brick work, plastering, painting, C.C. floor, mosaic floor, white
washing, distempering, varnishing, painting, doors and windows, DPC, centering and shuttering,
stone masonry, cement mortar, lime mortar, brick ballast, surkhi, cinder and sand.
SECTION C
ACCOUNTS PROCEDURES; Regular and work charged establishment, pay bill, ACR,
classifications of works, contract, tender, tender notice, earnest money, security money,
arranging contract, power of accepting tender, daily labour, muster roll, classification of
contracts, penalty, measurement book, account procedures of stores, issue rate, stock accounting,
form number 7,8,9,10,11,35,37, bill voucher, first and final bill, advance payment, hand receipt,
refund of security money, cash book, imprest, deposit works, temporary advances, treasury
challan, inventory, administrative approval, competent authority, building bye laws, arbitration.
104
SECTION D
VALUATION: Gross income, net income, outgoing, scrap value, salvage value, obsolescence,
annuity, capitalized value, years purchase, sinking fund, depreciation, valuation of building,
determination of depreciation, method of valuation, life of various items of works, mortgage-
lease, fixation of rates, plinth area required for residential building.
TEXT BOOKS:
1. Estimating & Costing in Civil Engg.: Theory & Practice by B.N. Dutta, UBS Publishers
Distributors Ltd.
2. Estimation and Costing in Civil Engineering, by Birdie, G.S., Dhanpat Rai Publishing
Co. ltd, New Delhi, 2011.
REFERENCE BOOKS:
1. Estimation, Costing, Specifications and Valuation in Civil Engineering, Chakraborti, M,
National Halftone Co. Calcutta.
2. Building Construction Estimating by George H.Cooper.
3. Estimating and Costing for Building & Civil Engg.Works by P.L.Bhasin.
4. Standard Schedule of rates and standard data book by Public Works Department.
5. I. S. 1200 ( Parts I to XXV 1974/ method of measurement of building and Civil
Engineering works B.I.S.)
105
CIVIL ENGINEERING SOFTWARE LABORATORY- CE 320 (P)

Name of Course Civil Engineering Software Laboratory
INSTRUCTIONS:

1. AUTOCAD Software
This course covers the essentials of AutoCAD Civil 3D. Students learn how to work with
point data in AutoCAD Civil 3D; create and analyze a surface; develop a site; model
corridors, and pipe networks; work with survey data; and import and export data.
2. STAAD PRO or Equivalent software,
EXERCISES:
1. 2-D Frame Analysis and Design
2. Steel Tabular Truss Analysis and Design
106
TRANSPORTATION ENGINEERING LABORATORY - CE 324 (P)

Name of Course Transportation Engineering Laboratory
INSTRUCTIONS:

1. To determine the impact value of aggregate sample

2. To determine the crushing value of aggregate sample
3. To determine the flakiness and elongation index of aggregate sample
4. To perform Los Angeles Abrasion test on aggregate sample
5. To determine the CBR value of a given soil sample
6. To carry out the grain size analysis of course aggregates & fine aggregates
7. To perform penetration test on bitumen sample
8. To determine the softening point of bitumen sample
9. To determine the specific gravity and water absorption of aggregate sample
10. To determine the ductility value of a bitumen sample.
11. To conduct Marshalls stability test on bituminous mix.
12. To determine the stripping value of coarse aggregate coated with bitumen
107
ENVIRONMENTAL ENGINEERING LABORATORY - CE 350 (P)

Name of Course Environmental Engineering Laboratory
INSTRUCTIONS:

1. To find the turbidity and colour of a given sample of water.
2. To determine the pH value of a given sample of water.
3. To determine the conductivity of a given sample of water.
4. To find out total dissolved solid, settleable solids and suspended solids of the given
sample.
5. To determine the carbonate, bicarbonate, and hydroxide alkalinity of a sample.
6. To find out the concentration of chlorides in the given sample of water.
7. To estimate the hardness of the given sample of water by standard EDTA method
8. To find the optimum amount of coagulant required to treat the turbid water by Jar
Test.
9. To determine residual chlorine in a given sample of water.
10. To determine MPN of coliforms of the given sample.
11. To determine the metal & metalloids of the given sample.
12. Determination of Fluorides.
13. Jar test for optimum coagulant dose estimation.
108
VII Semester
PRESTRESSED CONCRETE CE-411(a)
Course Code CE-411(a) L-3, T-1, P-0
Name of the Course Prestressed Concrete
Lectures to be delivered 52 (1 Hr Each) (L = 39, T=13 for each semester)
INSTRUCTIONS:
SECTION A
INTRODUCTION: Historic development General principles of prestressing pretensioning and
post tensioning Advantages and limitations of prestressed concrete Materials High strength
concrete and high tensile steel their characteristics.
I.S.Code provisions, Methods and Systems of Prestressing; Pre-tensioning and post tensioning
methods Analysis ofpost tensioning - Different systems of prestressing like Hoyer System,
Magnel System Freyssinet system and Gifford Udall System.
SECTION B
LOSSES OF PRESTRESS: Loss of prestress in pre-tensioned and post-tensioned members due
to various causes likeelastic shortage of concrete, shrinkage of concrete, creep of concrete,
Relaxation of steel, slip in anchorage bending ofmember and frictional losses.
Analysis of sections for flexure; Elastic analysis of concrete beams prestressed with straight,
concentric, eccentric, bent and parabolic tendons.
SECTION C
DESIGN OF SECTIONS FOR FLEXURE AND SHEAR: Allowable stress, Design criteria as
per I.S.Code Elastic designof simple rectangular and I-section for flexure, shear, and principal
stresses design for shear in beams Kern lines,cable profile.
ANALYSIS OF END BLOCKS: by Guyons method and Mugnel method, Anchorage zone
strusses Approximate method of design Anchorage zone reinforcement Transfer of
prestress pre-tensioned members.
SECTION D
Composite section: Introduction Analysis of stress Differential shrinkage General designs
considerations.
109
DEFLECTIONS OF PRESTRESSED CONCRETE BEAMS: Importance of control of
deflections factors influencing deflections short term deflections of uncracked members
prediction of long term deflections.
TEXT BOOKS:
1. Prestressed Concrete by Krishna Raju; - Tata Mc.Graw Hill Publications.
2. Prestressed Concrete by N.Rajasekharan; - Narosa publications.
REFERENCE BOOKS:
1. Prestressed Concrete by Ramamrutham; Dhanpatrai Publications.
2. Design of Prestressed concrete structures (Third Edition) by T.Y. Lin & Ned H.Burns, John
Wiley & Sons.
Codes: BIS code on prestressed concrete, IS 1343.
110
FINITE ELEMENT METHODS IN CIVIL ENGINEERING CE-411(b)
Course Code CE-411(b) L-3, T-1, P-0

Name of the Course Finite Element Methods in Civil Engineering
Lectures to be delivered 52 (1 Hr Each) (L = 39, T=13 for each semester)
INSTRUCTIONS:
SECTION A
Introduction: Concepts of FEM Steps involved merits & demerits energy principles
Discretization Rayleigh Ritz method of functional approximation.
Principles of Elasticity: Equilibrium equations strain displacement relationships in matrix form
Constitutive relationships for plane stress, plane strain and Axi-symmetric bodies of revolution
with axi-symmetric loading.
SECTION B
One Dimensional FEM : Stiffness matrix for bar element - shape functions for one dimensional
elements one dimensional problems.
Two Dimensional FEM : Different types of elements for plane stress and plane strain analysis
Displacement models generalized coordinates shape functions convergent and compatibility
requirements Geometric invariance Naturalcoordinate system area and volume coordinates
SECTION C
Generation of element stiffness and nodal load matrices for 3-node triangular element and four
node rectangular elements.
Isoparametric formulation Concepts of, isoparametric elements for 2D analysis -formulation of
CST element, 4 noded and 8-noded iso-parametric quadrilateral elements Lagrangian and
Serendipity elements.
SECTION D
Axi-symmetric analysis- Basic principles-Formulation of 4-node iso-parametric axi-symmetric
element
Solution Techniques: Numerical Integration, Static condensation, assembly of elements and
solution techniques for static loads.
111
TEXT BOOKS:
1. Finite Elements Methods in Engineering by Tirupati.R. Chandrepatla and Ashok D.
Belegundu - Pearson Education Publications.
2. Finite Element analysis Theory & Programming by C.S.Krishna Murthy- Tata Mc.Graw
Hill Publishers.
REFERENCE BOOKS:
1. Finite element analysis by S.S. Bhavakatti-New age international publishers
2. Finite element analysis by David V Hutton, Tata Mcgraw Hill, New Delhi
3. Concepts and Applications of Finite Element Analysis by Robert D.Cook, David
4. S. Malkus and Michael E.Plesha. Jhon Wiley & Sons.
5. Text book of Finite Element analysis by P.Seshu Prentice Hall of India.
112
OPEN CHANNEL FLOW CE-411(c)
Course Code CE-411(c) L-3, T-1, P-0

Name of the Course Open Channel Flow
INSTRUCTIONS:
which will cover the entire syllabus. Section A, B, C & D will have two questions from the
respective sections of the syllabus. Each section will have a weightage of 20% of the total marks
of the semester end examination for the course.
in Section E.
SECTION A
Types of open channels, Prismatic and non prismatic channel, classification of flows, continuity
equation, energy and momentum correction factors.
SECTION B
Specific energy, critical depth, critical flow computations, flow transitions. Uniform flow,
Chezys and Mannings equation, roughness coefficients, equivalent roughness, Hydraulically
efficient channel cross sections.
SECTION C
Gradually varied flow, governing equation, classification and analysis of flow profiles, GVF
computations.
SECTION D
Hydraulic jump, momentum equation for jump, classification of jumps, energy dissipation using
hydraulic jump, location of jump. Rapidly varied flow measurements, spatially varied flow.
Introduction to unsteady flow.
TEXT BOOKS:
1. Open Channel Hydraulics by Chow, V.T., Blackburn Press
2. Flow in Open Channel by Subramanya, K., Tata McGraw Hill Publications, New Delhi,
REFERENCE BOOKS:
1. Introduction to Fluid Mechanics by Robert W. Fax, Philip J. Pritchard, Alan T. McDonald,,
Student Edition 7th, Wiley India Edition, 2011.
2. Open Channel Flow: K. G. Rangaraju
3. Fluid Mechanics by Franck M White, Tata McGraw Hill Publication, 2011.
113
DESIGN OF STEEL STRUCTURES CE-412

Name of the Course Design of Steel Structures
INSTRUCTIONS:
in Section E.
SECTION A
Structural Steel: Types, properties and products
Basis of Structural Design: Structural systems, Loads and load combinations, Codes and
specifications, Design Philosophies, Failure criteria for steel
Design of tension members: Types of tension members, Slenderness ratio, behavior, modes of
failure, Angle under tension, other sections, design of axially loaded tension members, design of
lug angle, splices and gussets.
SECTION B
Plastic and Local Buckling Behaviour: Plastic theory, Plastic collapse load, Plastic collapse
theorem, Method of plastic analysis, Plastic design of Portal frames, Local buckling of plates,
Cross section classification, Behaviour and ultimate strength of plates.
Design of compression members: Possible failure modes, Behaviour, development of multiple
column curves, Sections for compression members, effective length, Single angle struts, design
of column, cross section (single and built up sections), Column bases and caps, displacement
SECTION C
Design of beams: Beam types, section classification, Lateral stability, Effective length, design of
Laterally supported beams, design of laterally unsupported beams, Shear strength of steel beams,
Maximum deflection, web buckling, crippling, purlins, design of beams.
Design of Beam Columns: General behaviour, equivalent moment factor, nominal strength,
interaction equation for local capacity check, design of beam column, beam column subjected ti
tension and bending, design of eccentrically loaded base plates.
114
SECTION D
Bolted Connections: Bolts, bolted connections, behaviour, ordinary black bolts, HSFG bolts,
Simple connections, Moment resisting connections, Beam to beam connection, Beam and
column splice
Welded Connection: welding processes, electrodes, advantages, types and properties, joints,
weld symbols, weld specifications, Effective area of weld, design of weld, simple joints, moment
resisting connections, continuous beam to column connection, beam and column splice.
TEXT BOOKS:
1. Subramanian, N, Design of steel structures, Oxford University Press, New Delhi
2. Duggal , S. K., Design of steel structures, Tata McGrawHill, New Delhi
REFERENCE BOOKS:
1. Trahair, N.S., The behaviour and design of steel structures, Taylor & Francis, London.
2. Chandra, Ram, Design of steel structures, Standard Publishers, Delhi.
3. Bhavikatti, S.S., Design of steel structures by limited method as per IS 800-2007, I.K.
International Publishing House, New Delhi
IS CODES: IS 800 2007, Code of Practice for general construction in steel, Bureau of Indian
Standards, 2007
115
DESIGN OF HYDRAULIC STRUCTURES CE-413

Name of the Course Design of Hydraulic Structures
INSTRUCTIONS:
in Section E.
SECTION A
CANAL HEAD WORKS: Introduction, functions, layout, selection of site for diversion head
works, various components and their functions, design of weirs on permeable foundation by
Blighs creep theory, Khoslas method of independent variables, use of Khoslas charts, silt
ejectors and their design principles.
CANAL REGULATION WORKS: Canal head regulators, cross regulators and distributory
head regulator, their functions, Design of canal head regulator & distributory head regulators.
SECTION B
CANAL FALLS: Necessity, types location of canal falls, types, design of Sarda and Glacis
falls, energy dissipation devices and arrangements.
CROSS DRAINAGE WORKS: Introduction, types of cross drainage works and their selection,
design of aqueduct.
SECTION C
STORAGE WORKS: Investigation and planning for reservoirs, capacity and yield, storage
works, types of dams and their choice, selection of suitable site.
GRAVITY DAMS: Types, selection of site, forces acting, stability criterion, Analysis of gravity
dam.
EARTH DAMS: Design aspects of earth dams, seepage through earth dams, seepage control,
design of filters.
SECTION D
ARCH DAMS: Constant angle and constant center arch dams (simple design and sketch),
buttress and multiple arch dams (Principle and sketch).
116
SPILWAY AND STILLING BASINS: Introduction, spillway capacity, different types, energy
dissipation below spillways, stilling basins: Type-I & II, gates and valves aerators.
TEXT BOOKS:
1. Irrigation Engineering & Hydraulic Structures by S.R. Sahasrabudhe, S K Kataria & Sons-
New Delhi
2. Hydraulic Structures by Novak, P., Moffat, A. I. B., Nalluri, C and Narayan, R, Taylor &
Francis.
REFERENCE BOOKS:
1. Irrigation Engineering and Hydraulic Structures by Garg, S.K., Khanna Publishers.
2. Handbook of Dam Engineering by Golze, A. R., Von Rostrand Reinhold Co.
3. Sharma, H.D., Concrete Dams, CBIP Publication, 1998.
4. Siddiqui, I H, Dams and Reservoirs: Planning, Engineering, Oxford University Press.
5. Theory and Design of Irrigation Structures Vol.I and II : R.S.Varshney
6. Fundamentals of Irrigation : Bharat Singh , Nem Chand Bros. Roorkee
117
WASTE AND SEWAGE TREATMENT CE-414

Name of the Course Waste and Sewage Treatment
INSTRUCTIONS:
in Section E.
SECTION A
SOLID WASTE MANAGEMENT: Solid waste generation, onsite handling, storage and
processing, collection, transfer and transport, processing techniques and equipments, recovery of
resources, conversion products and energy, disposal.
HAZARDOUS WASTE MANAGEMENT: Exposure and risk assessment, environmental
legislation, characterization and site assessment, waste minimization, incineration,
transportation, storage, landfill disposal facility siting, site remediation.
SECTION - B
BIOMEDICAL WASTE MANAGEMENT AND HANDLING: Biomedical waste management
issues, waste generation, current practices in health care facilities, environmental concerns,
labeling and color coding for waste storage, collection, transportation, treatment, common
treatment facility, disposal.
SECTION C
ECOLOGY AND ENVIRONMENT: Role of ecology in environmental issues, salient features of
major ecosystems, energy transfer, local, regional and global impacts, ecological chain and
balance, quantitative ecology in the context of environmental impact assessment of development
projects.
SECTION D
AIR POLLUTION: Sources, emission of gases, suspended particulate matter, classification
dynamics of pollutant dispersion and disposal, effects on environment including living and non-
living matter, remedial measures and their effectiveness, environmental assessment, acts relating
to air pollution, standards.
118
NOISE POLLUTION: Properties of sound waves, characterization of noise, kinetics of noise,
rating systems, measurement and control, standards.
TEXT BOOKS:
1. Integrated Solid Waste Management by G.Tchobanoglous, H.Theisen, S.Vigil., Mc Graw
Hill Inc.
2. Wastewater Engineering - Collection, Treatment, Disposal and Reuse, by Metcalf and Eddy,
McGraw Hill Pub. Co.
REFERENCE BOOKS:
3. Hazardous Waste Management, C.A. Wentz. Tata McGraw Hill Inc.
4. Hazardous Waste Management, M.D. LaGrega, P.L. Buckingham and J.C. Evans, published
by McGraw Hill (1994)
5. Industrial Waste Treatment, by Nelson Leonard Nemerow, Butterworth-Heinemann.
6. Solid Waste Engineering, by Vesilind PA, Worrell W and Reinhart D, Brooks/Cole Thomson
Learning Inc.
7. Hand Book of Environmental Laws, Acts, Rules, Guidelines Compliances and Standards (Vol
I & II).
8. CPHEEO (Ministry of Urban Development, New Delhi). Manual on Municipal Solid Waste
Management
119
PROJECT PLANNING AND CONSTRUCTION EQUIPMENTS CE-415

Name of the Course Project Planning and Construction Equipments
INSTRUCTIONS:
in Section E.
SECTION A
CONSTRUCTION PLANNING AND NETWORK TECHNIQUES: An overview of planning
process, Planning through bar charts, mile stone charts, difference between CPM and PERT,
basic concept of network preparation, applications in construction planning, scheduling and
control, funds, material, labour and equipment planning using network technique.
SECTION - B
CONSTRUCTION ORGANISATION AND MANAGEMENT: Different types of organization,
their structures, advantages and limitation, Quality control in construction, Cost account and
motivation.
SECTION C
SYSTEM TECHNIQUES IN CONSTRUCTION: An overview of systems techniques with
special reference to their applications in construction. These includes LP and its extensions viz.
assignment and transportation problems, queuing theory.
SECTION D
CONSTRUCTION PLANT AND EQUIPMENT: Preparatory work, Factors affecting selection
of equipment, Bulldozer, Dumpers, Trenchers, Excavators, Hoe, Hoists, Graders, Piling
hammers, Pumps, Compressors, Bitumen mix plant, Rollers, Clam shell, Aggregate production
techniques, Crushers, Concrete production, Jumbo, mucker, muck cars, Steam curing.
SAFETY IN CONSTRUCTION: Causes of accidents, preventive measures.
120
TEXT BOOKS:
1. Project Planning and Control with PERT and CPM, by B.C. Punmia and Khandelwal K.K.,
Laxmi Publication Delhi.
2. Construction Planning Equipment and methods, by Puerifoy R.L., McGraw-Hill Co,.
REFERENCE BOOKS:
1. Project Management, by Choudhary S, Tata McGraw Hill Publishing Co.
2. Construction Planning and Equipment by Satyanarayanan and Saxena, Standard Publishers
and distributors, New Delhi
3. PERT and CPM by L.S Srinath, Affiliated East-West Press Pvt Ltd
4. Srivastva, U.K., Construction, Planning Management, Galgotia Publisher.
5. Ramaswamy, R., Practical Handbook on Construction Management for Architects and
Engineers, Nabhi Publications.
121
STRUCTURAL DRAWING CE-412(P)

Name of Course Structural Drawing
INSTRUCTIONS:

LIST OF DRAWINGS:
Indian standard specification for Drawing.
Structural Drawing of reinforced concrete Structures: Rectangular Beam, T- Beam, L- Beam,

One way and Two way slab, Flat slab, Waffle Slab, Doglegged staircases, Open Well type, tread
rise staircase, cantilever/ spiral staircase, Columns, Isolated Footing, strip, raft and pile
foundation, Water tank, Retaining walls.
Structural Drawing of steel structures: Bolted and welded Connections, trusses, lacing and
battening, Column splices, Column Bases, plate girders.
122
WASTE AND SEWAGE TREATMENT LABORATORY CE-414(P)

Name of Course Waste and Sewage Treatment Laboratory
INSTRUCTIONS:

List of Experiments:
1. Determination of DO.
2. Determination of BOD.
3. Determination of COD.
4. Determination of Sulphates.
5. Determination of Nitrite and Nitrate nitrogen.
6. Determination of Ammonical and Total Kjeldhal Nitrogen.
7. Determination of phosphorus (total and available).
8. Determination of SVI (including MLSS and MLVSS estimations).
123
Semester VIII
Elective II
ROCK MECHANICS CE-421(a)
Course Code CE-421(a) L-3, T-1, P-0

Name of the Course Rock Mechanics
Semester End Examination Max. Time = 3 hrs. Max. Marks: Min. Pass Marks:
100 40
INSTRUCTIONS:
in Section E.
SECTION A
Introduction: Rock Mechanics and its relationship with soil mechanics and engineering
geology, application of rock mechanics to civil engineering problems.
Classification of rocks: Lithological classification, engineering classification of rocks,
classification based on wave velocity ratio, R.Q.D. Classification of rock masses i.e. RMR and Q
systems.
SECTION B
Rock properties: Laboratory test, compression, tensile, void index, permeability and shear,
effects of size of specimen, rate of testing, confining pressure etc. Stress strain curves of typical
rocks, strength of intact and fissured rocks, effects of anisotropy, saturation and temperature
effects, shear strength of jointed rock mass.
Field test: Uniaxial tests in tunnels and open excavations, shear test, pressures tunnel tests etc.
SECTION C
Stability of rock slopes: Mode of failure of rock slopes, plane wedge analysis, 3Dwedge
analysis circular mode of failure, back analysis of slopes, stability charts, types and design of
rock bolts.
Determination of in situ stresses: Stresses in rock, methods of determining in situ stresses i.e
hydraulic fracturing, flat jack test and over coring.
124
SECTION D
Design of tunnels: Rock pressure theories, ground reaction curve, rock support interaction
analysis empirical and semi empirical methods of analysis, simple method of tunnel, design,
types and design of tunnel lining.
Foundation of rocks: Stress distribution in foundation, methods of determination of bearing
capacity of rocks, improvement of rock properties, pressure grouting for tunnels and dams,
dental concreting, shear zone treatment.
TEXT BOOKS:
1. Introduction to Rock Mechanics, by Goodman R.E., John Wiley and Sons, New York.
2. Rock Mechanics for Underground Mining, by Brady B.H.G. and Brown E.T., Kluwer
Academic Publishers.
REFERENCE BOOKS:
1. Engineering in Rocks for Slopes, Foundations and Tunnels, by Ramamurthy T., PHI
Learning Pvt. Ltd.
2. Rock Mechanics in Engineering Practice: K.G. Stagg , Jojn Wiley & Sons.
3. Under ground excavation in rock: Evert Hoek, Edwin T. Brown, Institution of Mining and
Metallurgy
4. Rock Mechanics in Engineering Practice : by C Jaeger, Cambridge University
125
REMOTE SENSING AND G I S CE-421(b)
Course Code CE-421(b) L-3, T-1, P-0

Name of the Course Remote Sensing and G I S
Semester End Examination Max. Time = 3 hrs. Max. Marks: Min. Pass Marks:
100 40
INSTRUCTIONS:
in Section E.
SECTION A
INTRODUCTION: Introduction to Remote Sensing data acquisition and processing, Sensor
Systems, applications, Electromagnetic Radiation (EMR) and its characteristics, Radiation
principles: Plancks Law, Stefan Law, Weins Displacement Law, Kirchoffs Law, Properties of
solar Radiant energy, atmospheric windows.
SECTION B
PHYSICAL BASIS OF REMOTE SENSING: Interaction in the atmosphere: Nature of
atmospheric interaction, atmospheric effects on visible, near infra-red, thermal and microwave
wavelengths, interaction at ground surface, interaction with soils and rocks, effects of soil
moisture, organic matter, particle size and texture, interaction with vegetation, spectral
characteristics of individual leaf, vegetation canopies, effect of leaf pigments, cell structure,
radiation geometry.
SECTION C
PLATFORM AND SENSORS: Multi concept in remote sensing, general requirements of a
platform, balloon aircraft, satellite platforms, sun-synchronous orbits, sensors for visible and
near infra-red wavelengths, profilers, images, scanners, radiometers, optical-mechanical and
push button scanners, spectral, spatial, radiometric and temporal resolution, IFOV, FOV,
Geometric characteristics of scanners, V/H ratio, comparison of some satellite /aerial platforms
and sensors and remote sensing data products, Landsat MSS and TM, SPOT, IRS, ERS etc.
126
SECTION D
GEOGRAPHICAL CONCEPTS AND TERMINOLOGY: Difference between Image
Processing System and Geographical System (GIS), Utility of GIS, Various GIS Packages and
their Salient Features, Essential Components of A GIS, Scanners and Digitisers, Raster and
Vector Data, Data Storage, Hierarchical data, Network Systems, Relational database, Data
Management, Conventional database Management Systems, Spatial Database Management, Data
manipulation & analysis, Reclassification and aggregation, Geometric and Spatial operation on
Data Management and Statistical Modeling, Applications of GIS in various Natural Resources &
Engineering applications.
TEXT BOOKS:
1. Remote sensing and image Interpretation, by Lillisand T.M and Kiefer R.W, John Wiley and
Sons.
2. Concepts and Techniques of Geographic Information Systems, by C.P. Lo, Albert K. W.
Yeung, Prentice Hall India Pvt. Ltd, New Delhi.
REFERENCE BOOKS:
1. Remote sensing principles and interpretation, by Floyd F. Sabins, W.H. Freeman and Co.
2. Elements of photogrammetry, with air photo interpretation and remote sensing, by Paul R.
Wolf, McGraw Hill International Book Company.
3. Introduction to Geographic Information Systems, by Kang-Tsung Chang, Tata McGraw Hill
Publishing Company Ltd, New Delhi.
4. Principles of Geographical Information Systems, by Peter A. Burrough and Rachael A.
McDonnell, Oxford University Press.
5. Principles of Geographical Information Systems for Land Resources Assessment by P.A.
Baurrough Oxford University Press
6. Geographical Information Systems: A Management Perspective, Stan Aromoff, WDL
Publication
127
REPAIR AND REHABILITATION OF STRUCTURES CE-421(c)
Course Code CE-421(c) L-3, T-1, P-0

Name of the Course Repair and Rehabilitation of Structures
INSTRUCTIONS:
in Section E.
SECTION A
Aging of structures performance of structures need for repair and rehabilitation Distress in
concrete / steel structures, Causes of distress, Damage assessment and Evaluation models
evaluation methods for condition, strength, serviceability
SECTION B
Damage testing methods, Non Destructive testing methods, Semi destructive testing and
Destructive test methods,
SECTION C
Methods of repairs - Repair and maintenance of buildings, Repair materials, repair techniques,
and quality control methods for repair of concrete, masonry, steel and timber.
SECTION D
Retrofit techniques required in structures resulting from change in function, loading, and seismic
forces, retrofit of foundations, base isolation and energy dissipation, Retrofit of Historical and
heritage buildings.
TEXT BOOKS:
1. Handbook of seismic retrofit of buildings, CPWD, IBC and IIT Madras, Narosa Publishing.
2. Seismic design, assessment and retrofitting of concrete buildings by Michael N. Fardis
Springer
128
REFERENCE BOOKS:
1. Retrofitting Design of Building Structures by Xilin Lu, CRC Press.

2. Earthquake-Resistant Structures: Design, Build and Retrofit by Mohiuddin Ali Khan
Butterworth-Heinemann.
3. Concrete Structures, Materials, Maintenance and Repair, by Denison Campbell, Allen and
Harold Roper, Longman Scientific and Technical UK
4. RN Raikar, Diagnosis and treatment of Structures in Distress, R and D Centre, Structural
Designers and Consultants, New Bombay, India,1994.
5. VK Raina, Concrete Bridge Practice Construction, Maintenance and Rehabilitation, 2nd
Edition, Shroff Publishers and Distributors, August, 2010.
6. WH Ransom, Building Failures, Diagnosis and Avoidance, 2nd Edition, E and F.N. Spon
Publishers, December 1987
7. Repairs of Concrete Structures, by Allen, R.T. and Edwards, S. C., Blakie and Sons, UK
8. Maintenance and repair of Civil Structures, B L Gupta and Amit Gupta, Standard Publishers,
New Delhi.
9. Handbook on Repair & Rehabilitation of RCC Buildings by Anil K Sharma ,CPWD.
10. Concrete Structures - Protection, Repair and Rehabilitation, Woodson R Dodge, Elsevier.
129
ADVANCED STRUCTURAL DESIGN CE-422

Name of the Course Advanced Structural Design
INSTRUCTIONS:
in Section E.
SECTION A
Design of water tanks: Analysis of beams curved in plan, design of R.C.C. rectangular and
circular water tanks resting on ground, design of underground tanks, design of overhead water
tanks.
SECTION B
Design of Slabs: Design of Ribbed slabs, Flat slabs, Introduction to Yield line theory for
reinforced concrete slabs, Yield line solutions based on work equations.
SECTION C
Design of Plate Girders: Introductions, Preliminary design procedure, Web penal subjected to
shear, Behaviour of transverse stiffners, Design of plate girder using IS 800 : 2007 provisions,
Welding of plate girder components, Proportioning of section.
SECTION D
Design of Industrial Buildings: Selection of roofing and wall material, selection of bay width,
Structural framing, Purlins, Girts and eaves strut, Plane trusses and End Bearings.
TEXT BOOKS:
1. Advanced Reinforced Concrete design by P C Vergese, PHI Learning Pvt Ltd
2. Steel Structures Design and Practice by N Subramanian, Oxford Higher Education
REFERENCE BOOKS:
1. N. Krishna Raju, Advanced Reinforced Concrete Design, CBS Publishers and Distributors
2. Reinforced Concrete Design by R.N. Krishna and R.N. Pranesh, New Age International (P)
Limited
130
WATER RESOURCES AND SYSTEM ENGINEERING CE-423
Name of the Course Water Resources and System Engineering
INSTRUCTIONS:
in Section E.
SECTION A
Water Resources: Surface and Ground water resources: its geographic distribution within India.
Water resources development projects purposes and planning strategies. Intra- and Inter-basin
development concepts. Single- and Multi-purpose projects; Storage and Diversion schemes;
Conjunctive use of surface and ground water.
SECTION B
Stormwater Management & Frequency Analysis: Urban Hydrology; Quantity and Quality
Management, Issues; Detention and Retention systems, Histograms; Risk and Reliability;
Frequency Distributions; Estimation of Extreme Events.
SECTION C
Hydraulics of alluvial rivers: regimes and morphology. Critical tractive force and resistance
relations. Suspended, Bed and Total loads. Meandering, Braiding, Aggradation and Degradation.
Routing of floods reservoir and channel routing. Flood frequency studies, Flood forecasting.
SECTION D
Managing our water resources: Erosion control and watershed development: their benefit
towards conservation of national water wealth. Rain water harnessing and recharge of ground
water: role of society and peoples participation for sustainable water resource development.
Mitigation strategies for flood damage: structural and non-structural measures. Water
distribution: Delivery strategies, Command Area Development, System of regulation and control
of canal water, Outlets (modules), Assessment of canal revenue. Economics of water resources
systems.
TEXT BOOKS:
1. Bedient, Philip B., and Huber, Wayne C., Hydrology and Floodplain Analysis, 2nd Edition,
Addison-Wesley Publishing,
2. McCuen, Richard H., Hydrologic Analysis and Design, Prentice-Hall
REFERENCE BOOKS
1. Viessman, Knapp, Lewis and Harbaugh, Introduction to Hydrology, 3rd Edition, Harper and
Row Publishers, 1989.
2. Ponce, Victor Miguel, Engineering Hydrology: Principles and Practices, Prentice-Hall, Inc.,
1989.
131
EARTHQUAKE RESISTANT DESIGN CE-424

Name of the Course Earthquake Resistant Design
INSTRUCTIONS:
in Section E.
SECTION A
Introduction to Structural Dynamics : Theory of vibrations Lumped mass and continuous
mass systems Single Degree of Freedom (SDOF) Systems Formulation of equations of
motion Undamped and damped free vibration Damping Response to harmonic excitation
Concept of response spectrum.
Multi-Degree of Freedom (MDOF) Systems : - Formulation of equations of motion Free
vibration Determination of natural frequencies of vibration and mode shapes Orthogonal
properties of normal modes Mode superposition method of obtaining response.
SECTION B
Earthquake Analysis : - Introduction Rigid base excitation Formulation of equations of
motion for SDOF and MDOF Systems Earthquake response analysis of single and multi-
storyed buildings Use of response spectra.
Codal Design Provisions : - Review of the latest Indian seismic code IS:1893 2002 (Part-I)
provisions for buildings Earthquake design philosophy Assumptions Design by seismic
coefficient and response spectrum methods Displacements and drift requirements Provisions
for torsion.
SECTION C
Earthquake Engineering : - Engineering Seismology Earthquake phenomenon Causes and
effects of earthquakes Faults Structure of earth Plate Tectonics Elastic Rebound Theory
Earthquake Terminology Source, Focus, Epicenter etc - Earthquake size Magnitude and
intensity of earthquakes Classification of earthquakes Seismic waves Seismic zones
Seismic Zoning Map of India Seismograms and Accelegrams.
Codal Detailing Provisions : - Review of the latest Indian Seismic codes IS:4326 and IS:13920
provisions for ductile detailing of R.C buildings Beam, column and joints
132
SECTION D
Aseismic Planning : - Plan Configurations Torsion Irregularities Re-entrant corners Non-
parallel systems Diaphragm Discontinuity Vertical Discontinuities in load path Irregularity
in strength and stiffness Mass Irregularities Vertical Geometric Irregularity Proximity of
Adjacent Buildings.
Shear walls : - Types Design of Shear walls as per IS:13920 Detailing of reinforcements.
TEXT BOOKS:
1. Dynamics of Structures Clough & Penzien, McGraw Hill International Edition.
2. Earthquake Resistant Design of Structures Pankaj Agarwal & Manish Shrikhande Printice
Hall of India, New Delhi
REFERENCE BOOKS:
1. Dynamics of Structures by A.K.Chopra Pearson Education, Indian Branch, Delhi.
2. Earthquake Tips by C.V.R.Murty, I.I.T. Kanpur.
3. Structural Dynamics by Mario Paaz.
IS Codes: IS:1893, IS:4326 and IS:13920.
133
CIVIL ENGINEERING SOFTWARE LABORATORY -II CE-420(P)

Name of Course Civil Engineering Software Laboratory -II
INSTRUCTIONS:

1. Drawing using AUTOCAD SOFTWARE
Infiltration gallery (with one infiltration well, one straight gallery pipe, one inspection
well and one jack well).{Practice Only}
Rapid Sand Filter,
Septic Tank with dispersion Trench/ Soak pit.
R.C.C square overhead tank supported by four columns.
R.C.C Slab Culvert with splayed wing walls.
Two span Pipe Culvert.
Two span Tee Beam Bridge with square returns.(Practice Only)
Road Over Bridge (Pile foundation, Pile Gap ,Column,
Pre cast Beams & Deck slab) {Practice Only}
2. Structural Engineering Drawings With Bar Bending Schedule
Simply supported one-way slab.
Simply supported two-way slab.
Restrained two-way slab.
Singly reinforced beam./ Doubly reinforced beam.
Tee Beams supporting continuous slab (practice only).
Dog-legged staircase.
Lintel and Sunshade (practice only)\
3. STAAD PRO or Equivalent software,
EXERCISES:
3. 3-D Frame Analysis and Design
4. Retaining Wall Analysis and Design
134

B Tech Civil Syllabus PDF

Uploaded by

Copyright:

Available Formats

B Tech Civil Syllabus PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

B Tech Civil Syllabus PDF

Uploaded by

Copyright:

Available Formats

H.P.

1st Semester Scheme and Distribution of Marks

Course Subject L T P/D Hrs Theory Practical Total

NS-103 (P) Engineering Chemistry Laboratory 0 0 2 2 25 25 50

2nd Semester Scheme and Distribution of Marks

Course Subject L T P/D Hours Theory Practical Total

3rd Semester Scheme and Distribution of Marks

Course No. Subject L T P/D Hrs Theory Practical Total

Course Subject L T P/D Hrs Theory Practical Total

Course Subject L T P/D Hrs Theory Practical Total

$$ - Industrial Training of 8 weeks duration after 6th Semester

Sr. No. Open Elective Sub. Code

Course Subject L T P/ Hrs Theory Practical Total

Course No. Subject L T P/ Hrs Theory Practical Total

Total theory marks = 6750

Grand total = 8700

Course Code NS-101 Credits- 04 L - 3, T- 1, P - 0

Course Code NS-102 Credits-4 L-3, T-1, P-0

Course Code NS-103 Credits- 04 L-03, T-01, P-0

Course Code HS-102 Credits-3 L-3, T-1, P-0

1. Business @ The Speed of thought, Bill Gates.

Course Code BE-102 L-3, T-1, P-0

Course Code BE-104 Credits-4 L-3, T-1, P-0

1. The C++ programming language ,Bjarne Stroustrup ,Addison Wesley , 2000.

Course Code NS-103(P) Credits-2 L-0, T-0, P-2

Instructions for paper setter / candidates

NOTE: At least 10 to 12 experiments to be performed.

Course Code HS-102 (P) Credits-2 L-0, T-0, P-2

Instructions for paper setter / candidates:

Note: Each practical should be performed twice for effectiveness.

1. Word processing a document.

Course Code BE-104 (P) L-0, T-0, P-2

Instructions for paper setter / candidates

NOTE: At least 10 to 12 experiments to be performed.

7. Write a program to convert days into years and weeks.

Course Code WS 101 L-0, T-0, P-3

Laboratory examination will consist of two parts:

Carpentry and Pattern making Shop: -

1. To make a lap joint.

Electrical and Electronics Shop: -

1. Workshop Technology by Chapman.

Course Code NS-104 L - 3, T- 1, P - 0

Course Code NS-105 L-3, T-1, P-0

Course Code Hs-101 L-3, T-1, P-0

Course Code BE-101 L-3, T-1, P-0

Course Code BE 105 L-3, T-1, P-0

Course Code BE-103 L-1, T-0, P-5

Course Code NS-105(P) L-0, T-0, P-2

Instructions for paper setter / candidates

1. To find the refractive index of a prism by using spectrometer.

Note: Each student is required to perform at least ten experiments.

Course Code BE 101a(P) L-0, T-0, P-2

Instructions for Paper setter/ Candidates

Laboratory examination will consist of two parts:

1. To verify KCL and KVL.

Note: All the practicals of Electrical should also be performed on breadboard.

Course Code BE 101b(P) Credits-2 L-0, T-0, P-2

Instructions for Paper setter/ Candidates

1. Familiarization with electronic components, and general purpose Laboratory equipment.