Kumar

MCB Distribution boards Enclosed motor, heating
and enclosures and lighting control

MCCB Panelboards HRC cartridge fuselinks
Switch and protection devices & fuse units
Power distribution components Industrial switch and fusegear Power factor correction capacitors
Smart solutions for

electrical distribution
in commercial and
industrial applications
2 POWER DISTRIBUTION COMPONENTS PG01414001U March 2015
Power distribution components
Contents
1 Product overview 5
2 Memshield 3 MCB distribution boards and enclosures 31
3 Distribution board switch and protection devices 45
4 Modular control and switching devices 53
5 Memshield 3 MCCB panelboards 65
6 Industrial switch & fusegear 93
7 HRC cartridge fuselinks & fuse units 105
8 Enclosed motor, heating and lighting control 115
9 Power factor correction capacitors 121
10 Technical data 125
Indices 185
POWER DISTRIBUTION COMPONENTS PG01414001U March 2015 3
Product overview
1
Eatons comprehensive range of power distribution

solutions have been developed to meet todays
challenging electrical sub-distribution applications
in commercial and industrial buildings. Through
a proven competency in electrical distribution,
Eaton delivers an innovative approach to aid
compliance with the wider regulatory requirements
associated with modern buildings.
1.1 TYPE A, SPN 125A DISTRIBUTION BOARDS AND PAN ASSEMBLIES.................................................................................... 6
1.2 TYPE B, TPN 125A/250A DISTRIBUTION BOARDS AND PAN ASSEMBLIES........................................................................... 8
1.3 TYPE B, TPN 250A DISTRIBUTION BOARDS........................................................................................................................... 10
1.4 DISTRIBUTION BOARD METERING SOLUTIONS................................................................................................................... 12
1.5 DISTRIBUTION BOARD SWITCH AND PROTECTION DEVICES............................................................................................. 13
1.6 MODULAR CONTROL AND SWITCHING DEVICES................................................................................................................. 14
1.7 MCCB PANELBOARDS AND PAN ASSEMBLIES...................................................................................................................... 15
1.8 SURGE PROTECTION DEVICES................................................................................................................................................ 16
1.9 INDUSTRIAL SWITCH & FUSEGEAR........................................................................................................................................ 17
Glasgow fuse-switch-disconnectors & switch-disconnectors...................................................................................................... 17
Glasgow busbar chamber system................................................................................................................................................ 18
Exel 2 switch-disconnectors & switch-disconnector fuses........................................................................................................... 19
Rotary isolators and changeover switches.................................................................................................................................. 20
Exel distribution fuseboards..................................................................................................................................................... 21
HRC cartridge fuselinks, carriers and bases................................................................................................................................ 22
1.10 ENCLOSED MOTOR, HEATING AND LIGHTING CONTROL.................................................................................................... 24
1.11 POWER FACTOR CORRECTION CAPACITORS......................................................................................................................... 26

1.1 Product overview
Type A, SPN 125A distribution boards
IP3X robust steel enclosure Modern, curved full door, covers all devices
to suit all applications
Twist action handle, with optional

door barrel locks also available
Hinged doors provide 180

opening for easy access
Removable gland plates are provided

top/bottom for ease of installation
High quality clear sub circuit

identification labels
Cover screwed by means of

combination screws
Dual rated MCBs 10/15kA to New 125A Switch Disconnector

IEC 60898 and IEC 60947-2 from 1A63A incomer option
Features & benefits General characteristics

Unique full form blanking modules for unused MCB Eatons Memshield 3 MCB Distribution boards have
ways. Provides secure shrouding of unused busbar stabs evolved through an intimate knowledge and feedback from
for increased electrical safety. Blanking modules have Electrical Contractors to provide solutions to a wide range of
interlinking form for improved positional security. electrical distribution applications in commercial buildings.
Main busbar is removable for flexible installation. Memshield 3 delivers safe, reliable and high performance
protection of electrical power distribution systems.
Fully shrouded Neutral busbar for increased safety.
Type A Distribution boards are fully type tested with a
Choice of metering option to suit application needs and aid conditional short circuit rating of 15kA to BS EN 61439.
compliance with latest Building Regulation part L2. Associated devices are high performance MCBs, developed
Door opens 180 to provide easy access and device operation. for Commercial and Industrial applications, dual rated at 10kA
IEC 60898 & 15kA IEC 60947-2 in B, C or D curves.
Standard incomer Switch Disconnector rating of 125A
provides higher rated solution for commercial buildings.
Optional coupling kit available to electrically connect
two distribution boards together vertically from a single
supply cable to expand number of MCB ways.

Product overview
Type A, SPN 125A distribution boards 1.1
Maximised wiring space for RCBOs when Fully shrouded Neutral busbar
incorporated within the installation for increased safety
Easy access earth bar can

accommodate up to 25mm2 cables
Combination scew heads on all devices
Unique full form blanking

modules for unused MCB ways Stand-off foot form for stable installation
Type A SPN distribution boards Incoming devices

The SPN boards are rated at 125A as standard and available in A range of incoming options are available, with the 125A SPSN
5 sizes with a choice of 4, 7, 10, 13 and 16 single pole outgoing switch disconnector being the most popular. In addition, there
ways. A choice of metering solutions are available as standard, are a number of 100A RCCB options, which provide the added
providing clear electrical consumption information as well as a security of earth fault protection, covering 30mA300mA
permanent capability of visualising information on a variety of applications. A direct connection terminal arrangement is also
other electrical parameters. The metering options have been available for applications not requiring local isolation. TypeA
developed to provide simple solutions to aid compliance with distribution boards can be stacked vertically to expand the
part L2 of the Building Regulations of England and Wales. A wide number of outgoing ways using the vertical interconnection kit.
range of accessories including full profile blanking modules for For larger SP applications, requiring more outgoing ways see
unused MCB ways and door locking options, enhance electrical our type B distribution boards with Single phase kit options.
safety, whilst clean earth kits and vertical inter-connection kits
to join two boards together, improves versatility of the range. Outgoing devices
For type A distribution boards, there is a choice of single pole
Type A SPN pan assemblies
MCBs plus RCBOs. MCBs are available in current ratings from
The SPN pan assemblies offer a high degree of flexibility 1A63A, with trip types B, C and D, 10kA to IEC 60898 and 15kA
for custom applications and inclusion in other factory built to IEC 60947-2. RCBOs to IEC EN 61009 10kA are also available
assemblies. SPN types are rated at 125A and available in a choice of trip sensitivity options from 10mA100mA.
with 4, 7, 10, 13, and 16 single pole outgoing ways.

Type B, TPN 125A/250A distribution boards

Modern curved edges enhance top/bottom for ease of installation.
appearance of board IP42 gland plate kit option
IP4X robust steel enclosure to suit

all applications. IP42 available
with gland plate accesory
Twist action access handle, with optional

door barrel locks also available
Gland plate
4 x screws, nuts
and washers
provided
Covers fit within enclosure dimensions
allowing adjacent mounting
Cable trunking Existing case end screws
Cable trunking interface kit fitting diagram Cable trunking interface kit available
Removable front door to aid

accessibility to devices
High quality clear sub circuit
identification labels
Secondary cover slides over two

location screws at bottom of
board for easier fastening
Features & benefits

Welded case end design board with removable gland plates Additional Functional Earthing options and Clean Earth options
provides super stiff construction, even with gland plates available.
removed. Construction virtually eliminates distortion during Auto-formed, curved construction of main cover adds to board
installation, ensuring final assembly fit and alignment. rigidity, with improved appearance.
Unique cable trunking interface kit simplifies mounting of cable Removable door aids installation and easy hang hinge design
trunking and protects cables. makes re-attachment of door simple.
Improved Neutral cable clamp design for simple & secure cable 125A Switch Disconnector Incomer for general commercial
connection. building applications.
Unique full form blanking modules for unused MCB ways, 250A options on 18 and 24 way boards.
provides secure shrouding of unused busbar stabs for increased
safety. Blanking modules have interlinking form for improved Compact 250A options on 18 and 24 way boards, where used
positional security. with cable trunking.
Removable busbar assembly to assist installation.

Product overview
Type B, TPN 125A/250A distribution boards 1.2
General characteristics
Eatons Memshield 3 MCB distribution boards have evolved Where used with 250A sized incomers, an extension
through an intimate knowledge and feedback from electrical box or the provision of suitable sized cable trunking is
contractors, consulting engineers and end users to provide required to accommodate incoming cabling. A new cable
solutions to a wide range of electrical distribution applications in trunking interface kit is available to provide additional
commercial buildings. Memshield 3 delivers safe, reliable and high mechanical protection of incoming cables.
performance protection of electrical power distribution systems. A choice of metering solutions are available as standard,
Type B distribution boards are fully type tested with a providing clear electrical consumption information as well as a
conditional short circuit rating of 25kA to BS EN 61439. permanent capability of visualising information on a variety of
Associated devices are high performance MCBs, developed other electrical parameters. The metering options have been
for commercial and industrial applications, dual rated at 10kA developed to provide simple solutions to aid compliance with
IEC 60898 & 15kA IEC 60947-2 in B, C or D curve. part L2 of the Building Regulations of England and Wales.
A wide range of accessories including full profile blanking modules
for unused MCB ways and door locking options, enhance electrical
safety, whilst clean earth kits improve versatility of the range.
Type B TPN standard distribution boards Incoming devices 125A standard TPN board
The optimised design for 125A TPN applications provides a The most popular choice will be the 125A switch disconnector
choice of boards in sizes 4, 6, 8, 12, 18 and 24 TP ways. 12, incomer option, but other choices include a 4-pole TPSN, 2P
18 & 24 TP way variants are also suitable for 250A applications, SPSN, a range of RCCB switches and a contactor controlled
where the number of MCB ways could require a larger supply incomer with switch disconnector for remote control of
current rating. A choice of incomers are available to suit different the supply to the board. A direct connection option is also
applications including RCCB options and a single phasing available for applications that do not require local isolation.
kit to provide a large single phase board arrangement.
Increased width of board to 440mm

to maximise wiring space
Dual rated MCBs 10/15kA to IEC 60898

Combination screw heads on all devices
and IEC 60947-2 from 1A63A
Unique full form blanking

modules for unused MCB ways
125A incomer kits available as

standard with 250A incomer options
Terminal shield covers for increased safety for 12, 18 & 24 way boards
Reversed Earth & Neutral bar

assembly, to ease installation and
improve access for testing
Type B SPN pan assemblies Improved neutral box clamp

with disconnection link
The TPN pan assemblies offer
a high degree of flexibility
for custom applications and
inclusion in other factory
built assemblies. 125A TPN
types are available with 4, 6,
8, and 12 triple pole outgoing
ways. 250A TPN types are
available with 12, 18, and 24
triple pole outgoing ways.

Type B, TPN 250A distribution boards
Type B, TPN 250A distribution board solutions
125A/250A board High load 250A board

18mm MCB only 18mm + 27mm MCB
Ways 18mm Ways 27mm

4 0 + 2
6
125A within standard enclosure

4 + 2
Integrated cable box as standard

8 6 + 2
16 10 + 2
12 16 + 2
250A incomer option on 12,
18 and 24 way boards only
18 22 + 2
24
Cable box or cable trunking

required for 250A incomer option
440mm 440mm
High load board has adequate

integral cabling space and no
extension box is required
Type B TPN 250A High Load distribution boards

Modern, curved edges enhance
top/bottom for ease of installation
appearance of board
Choice of SP & TP 18mm dual rated

MCBs 10/15kA to IEC 60898 and
Removable front door to aid IEC 60947-2 from 1A63A
accessibility to devices
Two TP 27mm MCB ways, rated up to 125A
Secondary cover, slides over two

location screws at bottom of
board for easier fastening
Covers fit within enclosure dimensions
allowing adjacent mounting

Product overview
Type B, TPN 250A distribution boards 1.3
Type B TPN 250A High Load distribution boards Outgoing devices
Developed to respond to the needs of modern commercial For type B distribution boards, there is a choice of single
building applications, a new 250A TPN range of MCB pole or triple pole MCBs plus SP and TP RCBOs. MCBs are
boards delivers increased versatility by having the ability to available in current ratings from 1A63A, with trip types B, C
supply and protect sub loads up to 125A. Based principally and D, 10kA to IEC 60898 and 15kA to IEC 60947-2. RCBOs to
around standard 18mm MCBs and RCBOs, this range IEC61009 10kA are also available in a choice of trip sensitivity
has provision for two TP 27mm MCBs, up to 125A. options from 10mA100mA. For the 250A High Load board,
Available in sizes 2, 6, 8, 12, 18 and 24 TP ways, of which provision is given to accommodate a number of 27mm MCBs
two ways are dedicated to the 27mm MCBs. 27mm MCBs available in SP or TP sizes from 20A125A to IEC 60947-2 .
are available SP or TP with ratings from 20A125A.
Incoming devices 250A TPN board

and 18/24 way 125A board
These incomer options can be used with the 250A board
or with the 18 or 24 way variant of the 125A board to
provide a greater choice of solutions at 250A.
The most popular choice will be the 250A TPN switch
disconnector incomer option, but other choices include
a 4-pole TPSN switch disconnector, a choice of MCCB
incomers from 160A to 250A and a contactor controlled
incomer pack. There is also a direct connection option
available for applications that do not require local isolation.
Combination screw heads on all devices
Terminal shield covers fitted

for increased safety
Complete range of incomer kits available
Maximised wiring space integrated

in the board length

Distribution board metering solutions
200A TPN type B distribution board, with Metering solutions type A metered boards
integrated split meter for power/lighting
Type A SPN boards with integrated meter.
TPN distribution board with smart Split load versions utilise a two channel
meter for power and lighting loads. meter, feeding two independent busbars
Unique meter design calculates net values and groups of MCB/RCBOs.
for each busbar section and total board load. Split load versions provide independent
Meter has both Pulsed and monitoring of Power and
Modbus outputs as standard. Lighting loads and total load.
Embedded vt technology and RJ 11 Aids compliance with Part L2 of the
connections at meter minimises visible wiring. Building Regulations (England & Wales).
Supplied complete with factory fitted 200A See page 127 for dimensions.
Switch Disconnector incomer switch.
Suitable for TPN and SPN applications
as supplied (shorting link included). Metering solutions type B
meter pack assemblies
Increased earthing options
supplied as standard. Eatons Memshield 3 meter packs provide
simple integration with matched aesthetics.
Split metering for separate small power and
lighting has been added to the range to meet
The feature packed Eaton the needs of the L2 Regulations introduced in
meter packs and boards England and Wales in 2006. The meters provide
a pulsed output for kWh and display other
To meet the needs of part L2 of the Building useful parameters, including line voltage and
Regulations introduced in England and Wales in current. Modbus versions are also available
2006, Eatons Memshield 3 meter packs provide and provide remote access to additional
simple integration with matched aesthetics. The electrical parameters. For details refer to
EBMMPCT250 employs a multi-function, DIN rail page 36. For dimensions refer to page 127.
mounted meter to measure electrical parameters
on LV supplies to TPN distribution boards. It can
also be used to meter single-phase loads. The
unit is supplied complete with CTs and wiring
terminals. This version is suitable for 100A250A
applications and as well as a pulsed output
for kWh, the meter can be used to monitor
other parameters, including line voltage and
current. Electrical connection to the associated
distribution board does not occupy any of the
outgoing circuits. Modbus and MID certified
meter versions are also available see page 36.
The EBMMPDC120 is supplied as a 120A direct
connection solution, not requiring CTs. Cabling
is simple and the meter provides a pulsed
output for kWh. The meter is an MID certified
unit, providing clear kWh information.
Double meter pack for two standard TPN
distribution boards facilitate separate
monitoring of small power and
lighting from one main supply.
For single phase EAM boards, a 65A meter
pack provides simple integration. (Amps, kW,
kWh, kVar and kVarh pulsed output, MID
compliant. See page 32 for single phase
EAM boards with factory fitted meters,
including split power and lighting boards.)

Product overview
Distribution board switch and protection devices 1.5
Miniature circuit breakers (MCBs)
Toggle colour for commercial MCBs changes
The Eaton range of 10kA/15kA high dependant on the rating as shown below:
performance miniature circuit breakers
(MCBs) have been designed to meet the
latest UK, European and international < 2A 16A
standards, with ratings from 1A up to 63A.
The Eaton miniature circuit breakers are
designed and tested in accordance with 2A 20A
BS EN 60898 and are available in B, C and
D characteristic curve as standard.
Technical characteristics 4A 25A
Modular design, DIN rail mountable.
1, 2, 3, and 4-pole MCBs for commercial
and Industrial applications. 6A 32A
Rated braking capacity 10kA to IEC
60898 and 15kA to IEC 60947-2.
Rated currents from 163A in B, 8A 40A
C and D characteristics.
Positive contact indication.
Box clamp barrier to prevent 10A 50A
incorrect cable/busbar insertion.
Calibrated at 40 C.
13A 63A
Can be used with both pin and
comb type busbars.
Suitable for use in Eaton Memshield3
distribution boards and a wide Residual current circuit breakers (RCCBs)
range of other applications.
The Eaton range of residual current
circuit breakers without integral overload
Residual current circuit breakers with protection (RCCBs), provide protection
overcurrent protection (RCBOs) solutions to a wide range of applications.
The Eaton range of combined residual current The Eaton range of 2 and 4-pole RCDs are
circuit breakers with integral overload protection available with 10mA, 30mA, 100mA and
(RCBOs), combine the highest level of protection 300mA sensitivities, and can be equipped
for both people and circuits for both single with a wide range of modular accessories
phase / single module and three phase / four
Technical characteristics
module devices. Fully comply to IEC 61009.
Modular design, DIN rail mountable,
Technical characteristics single phase RCBOs
2 or 4 modules wide.
Available from 6A to 45A in types B and C
Double and four pole RCD for commercial
trip characteristics with a choice of 10mA,
and industrial applications.
30mA, and 100mA trip sensitivities.
Rated short circuit capacity
Compact modular design, DIN rail
10kA with fuse back up.
mountable, one module wide.
Trip sensitivities 10, 30, 100 and 300mA.
Suitable for use in Memshield 3 single
and three phase distribution boards. Positive contact indication.
Unswitched neutral. Test trip button.
Positive contact indication. Rated currents from 16100A.
Rated breaking capacity 10kA.
Trip test button.
Technical characteristics three phase RCBOs

Options from 6A to 32A in type B, C, and D
trip characteristics with a choice of 30mA,
100mA, and 300mA trip sensitivities.
Compact modular design, DIN rail
mountable, four modules wide.
Suitable for use in Memshield 3
three phase distribution boards.
The RCBO takes up 4 pole ways in a 3-phase
Unswitched neutral. distribution board, i.e. L1 / L2 / L3 and the 4th
Positive contact and earth fault trip indication. pole of the device fits over, and is insulated from,
the L1 phase position of the neighbour circuit.
Rated breaking capacity 10kA.
Therefore the neighbour circuit only has two phase
Trip test button. circuits available for single phase circuit feeds.

Modular control and switching devices
Switches and Twilight Switches

Timers & Twilight Switches are applied in any residential, commercial and industrial buildings wherever automatic control
is required on predefined times and/or depending on daylight intensity.
The Eaton range comprises of a wide variety of different products which include analogue Timers, digital Timers, Twilight
Switches and Staircase Timers.
These Timers can either be controlled by a 50 Hz netsynchronisation, quartz control and time synchronisation or using the
DCF signal or GPS antenna, which guarantees 100% accuracy at all times. Except for net-synchronised timers all units
do have self power reserve to secure the time setting and program storage in case a power interruption does occur.
Dedicated computer software and memory cards are available to support the programming of our most advanced timers.
Automatic summer and winter time, holiday and random switching programs complete the functionality of our range.
Twilight Switches are supplied with a remote light sensor, which can be easily installed on the outside wall
where the required light intensity threshold can be simply adjusted on the modular device itself.
Technical characteristics (depending on type)

Modular design.
Analogue and digital timers.
Time adjustment by 50 Hz net, quartz control, DCF1) or GPS signal reception2)
Manual override switching function.
Power reserve for all quartz and DCF or GPS driven switches.
Remote Light Sensor for Twilight Switching.
Benefits
Easily programmable on front of device.
Computer aided programming software available.
Compact 18 mm design for restricted space opportunities.
Separate IP40 covers are available for direct wall mounting.
High level of accuracy.
Automatic summer and winter time adjustment.
Holiday & Random program settings.
High power reserve up to 10 years.
Notes: 1) Automatic calculation of sunrise and sunset times throughout the year, including the possibility of astro times + / -2 hour shift.
2) The DCF-signal can only be received within a 1000 km radius.
Contactors and impulse switches

Contactors are frequently applied for switching of lamp loads, fans or pumps in both utility as well as industrial areas.
Eatons CR contactors are very specific due to the applied operating coil and the construction of the main contacts.
All contactors with ac/dc coils ensure silent operation which is further enhanced by a low power consumption.
Optimal contacts and low heat dissipation guarantee a long lifetime of the contactor which is available in a wide range of
characteristics.
Designed according to IEC 60947-4-1 and IEC 61095 standards.
Suitable for applications in general control, heating & lighting applications.
Available in 20, 25, 40 & 63 A ratings with up to 4-pole contacts.
Optional add-on auxiliary contact available.
DIN modular profile.
Spacers available to extend lifetime (it is recommended to use 1 spacer between every 2 contactors installed).
Day/night contactors available with manual override function.
Advantages of Eaton contactors

Low inrush power for all ac/dc types.
Availability of combined ac/dc type contactors ensure silent operation.
Contactors of ac/dc coil type are operable on both ac and dc voltage. The 20 A and 25 A versions are also available
with ac coil. All combined ac/dc type versions are equipped with surge protecion on the operating coil.
Equipped with contact indication.
Optimal quality of contacts and low heat dissipation ensure a long life time.

Product overview
MCCB panelboards and pan assemblies 1.7
The feature packed Memshield 3 MCCB
panelboard distribution system
A complete range of MCCB panelboards and pan assemblies
providing all the options you need from a straightforward
panelboard to a comprehensive panelboard system. The range
now offers a variety of incoming devices and a greater choice of
outgoing ways to provide more flexibility and choice to the user.
250A, 400A, 630A & 800A panelboard versions available.
Can be configured for incomer device at top of panelboard.
3 or 4 pole incoming devices can be fitted.
4 to 18 outgoing TP ways.
Outgoing MCCBs up to 400A, available in
25, 36 and 50kA breaking capacity.
All TP & 4P MCCBs have adjustable thermal and magnetic trip
units as standard except for 630A and 800A incomer MCCBs
which are fixed thermal / adjustable magnetic trip. MCCBs with
additional trip unit functionality are available to special order:
Distribution circuit protection, electronic.
Motor protection, thermal/magnetic.
Motor protection, electronic.
Motor protection without overload release.
Selective (discriminative) and generator protection, electronic.
IP3X construction.
Form 3b type 2 segregation.
Tinplated busbar systems throughout the range.
Incoming and outgoing metering options to ensure Part
L2 Building Regulations compliance. Plug-in cabling
system provides for faster and error-proof installation.
Reliable & safe operation assured through
DEKRA testing & certification.
Wide range of extension boxes, metering, surge protection,
and earth leakage incomer options available.
Versatile solution, accommodating different frame size
outgoing MCCBs to best match application needs.
Enhanced safety through fully shrouded incoming
devices, to protect against contact with live parts.
Blanking plates finger protect unused outgoing ways.
Factory built assemblies

Complete factory built assemblies can be specified for individual
projects, on which the factory will be pleased to advise.
Simple derivatives include: The fitment of side extension
boxes, dual incomers and metering options etc.
Option to remove top and bottom cross rails provides the ability
Through a modular panelboard system, more custom to lay cables into the board instead of feeding them through
solutions can be accommodated to include: the gland plate aperture, resulting in big time savings.
4-pole switching options.
Fused combination switch options for both
incomers and outgoing ways.
Form 4 type 2 solutions.
For more details on these services please contact
our customer support team on 08700 545 333.

Surge Protection Devices
Surge protection devices (SPD) for MCB distribution boards and MCCB panelboards
In order to enable designers, specifiers, and installers to comply with surge protection requirements
in BS 7671 - IET Wiring Regulations - 17th Edition (Section 534), Eaton has a combined lightning
current and surge arrester, as well as an individual surge arrester to provide a coordinated
solution for lightning protection and surge suppression fully tested to BS EN 62305. This range of
coordinated enclosed kits provides peace of mind that all equipment has comprehensive transient
overvoltage protection caused by lightning strokes and switching in low voltage systems.
Surge arrester protection for distribution boards

EM3SSK1T2 (SPN distribution boards) & EM3SSK3T2 (TPN distribution boards) technical summary:
For the protection of low voltage distribution systems against transient
overvoltage caused by indirect lightning strike and switching operations.
The 3+1 circuit offers a universal solution for surge protection in low voltage distribution systems.
Suitable for TT- and TN-S systems according to IEC 60364-5-53 Clause 534.
Test class II according to IEC 61643-1+A1.
SPD-type T2 according to EN 61643-11.
Combined lightning arrester and surge arrester protection

for distribution boards and panelboards
EM3SSK3T12 (TPN distribution boards) & EPBN1SPD123 (panelboards) technical summary:
Lightning protection classes III and IV in accordance with IEC 62305.
For the protection of low voltage distribution systems against transient overvoltage
caused by direct and indirect lightning strike and switching operations.
Application according to IEC 60364-5-53 Clause 534.
Test class I, II, III in accordance with IEC 61643-1.
SPD-type T1, T2, T3 in accordance with EN 61643-11.
Combined lightning arrester and surge arrester protection for panelboards

EPBN1SPD1234 technical summary:
Lightning protection classes I, II, III and IV in accordance with IEC 62305.
For the protection of low voltage distribution systems against direct lightning
strike into the overhead power supply line or external lightning protection
system and against indirect lightning stroke and switching operations.
No discharge of ionised gases during operation.

Product overview
Industrial switch & fusegear 1.9
Glasgow fuse-switch-disconnectors & switch-disconnectors
For many years, the Glasgow product name has been synonymous with quality, trust and reliability
and as part of our long standing commitment to its tried and tested design weve reinvested
for the future by re-tooling the whole range. All units are supplied with fuselinks or switchlinks
fitted. Glasgow fuse switch disconnectors and switch disconnectors meet the constructional
requirements for isolation of and are type tested to BS EN 60947-3. Conditional short circuit
current rating tests at a value of 80kA rms Ue 415V have been carried out with Eaton HRC fuses
fitted. Five frame sizes are available to provide a range from 63A to 800A, with utilisation category
AC22A and AC23A Ue 415V ratings. Switch-disconnectors fitted with copper links give assigned
AC20A Ui 660V and AC21A Ue 415V ratings. All units have retractable operating handles which
drive overcentre mechanisms incorporating powerful operating springs. Opening and closing of
the switches is thus independent of the action of the operator. Moving contact assemblies can
be removed to facilitate installation or for contact inspection or renewal. Flag on-off indication is
provided and terminal cover shields prevent contact with live metal. TPSN indicates triple-pole and
switched neutral, the neutral pole making first and breaking last. Rated Insulation Voltage Ui 660V.
Enclosures
Surface-mounting enclosures comprise heavy gauge steel body plates incorporating cast iron
frame members and are rustprotected, with a light grey paint finish (RAL7004). Front access
doors, which are detachable, are fitted with dust-excluding gaskets and are interlocked to
prevent opening when the switch is on. The interlock can be defeated by a competent person
for maintenance purposes. Operating handles may be locked in both the on and off positions.
Castell type interlocks can be supplied to special order. Internal fixing holes allow units to
be mounted closely side by side and all models have removable top and bottom end plates.
These are pierced for connections, divided into front and rear (fixed) portions to simplify cabling
using Eatons MEM series split-type cable boxes, and provided with undrilled cover plates.
Fuses
Glasgow units are designed for use with HRC cartridge fuse links to BS88: Part 2. 63A and 100A
units employ off-set contact fuse links. Details of suitable types of HRC cartridge fuse links are
listed on page 101. All performance tests have been carried out using Eaton BS88 fuselinks.
Motor ratings
The motor ratings assigned to TPN switch-disconnector units are utilisation category AC23A
(frequent operation) to BS EN 60947-3, which calls for make and break testing at 10 and 8
times rated current respectively for units having a motor rating up to and including 100 Amps.
Ratings for switch-disconnector-fuses are dependent on suitable HRC fuses being fitted.
Auxiliary equipment
A comprehensive range of extension boxes and spreader boxes is available. Units are
fitted with HRC Fuselinks of maximum rating but will accept fuselinks of a lower rating,
refer to the Paramount HRC Fuselinks section on page 101. SPSN and TPSN indicate
switched neutral. Neutral makes first and breaks last. If DP fuse-switch-disconnectors are
required, use SPSN and replace the supplied switch link with a compatible fuselink.
Definitions of utilisation category

AC20a Connecting and disconnecting under no load condition.
AC21a Switching of resistive loads including moderate overloads.
AC22a Switching of mixed resistive and inductive loads including moderate overloads.
AC23a Switching of motor, or other high inductive loads.
Cable extension boxes

Fabricated sheet steel boxes boxes can be fitted top/bottom of Glasgow switch units to provide
additional space for spreading multi-core PVC insulated cables with solid aluminium conductors
and for some larger cables with stranded copper conductors. For 13PCB, a plain flame retardant
plywood plate is provided for fitting between the box and switch unit, the steel endplate supplied
fitted to the switch unit being used on the boxs cable entry side. For 4PCB, a plain steel plate is
provided for cable entry on box. The switch enclosure has 8mm thick insulated endplates fitted
both ends. For 56PCB, a 10mm thick insulated plate is provided for cable entry on box. The switch
enclosure has 10mm thick insulated endplates fitted both ends, 5PCB includes a flame-retardant
plywood packer for fitting between PCB and switch units endplate to provide lid flange clearance.

Industrial switch & fusegear
Spreader boxes
Cast metal split pattern, supplied with fixing bolts and plain bushes. Two types are available,
suitable for straight or angled entry. They permit conductor spreading of larger PVC cables
and fit directly on to Glasgow fuse-switch-disconnectors and switch-disconnectors.
Glasgow busbar chamber system

Eatons busbar chamber system is designed to provide either compact, wall-mounting installations
or by using optional pedestal sets easily assembled switchboards. Every facility is provided
to enable Eatons switchgear and distribution gear to be mounted easily and economically to
busbar chambers which can be applied either to a suitable load-bearing vertical surface; or,
by means of a pedestal set, affixed to a vertical surface which need not be load-bearing.
Busbar chambers
These are produced in 100, 200, 400, 630 and 800 Amp. ratings and in four nominal lengths.
100, 200 and 400 Amp units are available in all four sizes; 630 and 800 Amp ratings are offered in
the three longest units only. All units in the range share the same height and depth dimensions.
Similarly the twin busbars are located in precisely the same positions throughout the range and
vary in size only in their front-to-back dimensions according to rating. Detachable end plates enable
all units to be extended by coupling to a second busbar chamber using extension sets. Both top
and bottom plates are also readily detachable so that marking out and machining can be carried out
conveniently on a bench to accommodate Eatons switchgear either above or below the chamber.
Complete mounting kits, including templates, are available for mounting all Exel and Glasgow
switchgear. Eaton chambers are fabricated from rust-protected sheet steel with a light grey paint
finish. They have been type tested to BS EN 61439 with a rated conditional short circuit current
rating of 63kA at Ue 550V and a rated short-time withstand current Icw 20 times nominal rated
current for one second. They are designed for use in factory-built assemblies to BS EN 61439. All
chambers are subjected to an on-line dielectric test unit which provides a high voltage test between
poles; and from poles to earth. Earth continuity is also tested. Rated insulation voltage 660V.
Connection sets for Glasgow fuse-switch-disconnectors & switch-disconnectors

Cable clamps covering all ratings are available for switchgear up to 200A. For connecting
Glasgow units of 160A and above, solid copper connection sets are recommended as cost
effective and convenient. These comprise pre-formed, insulated links in 4-pole sets supplied
with all necessary clamps and fasteners. The appropriate switchgear mounting set (41,
51 or 61 BBMS) must be used with connection sets for 160800A Glasgow units.
Busbar cable clamps and sockets

Incoming main cable clamps or sockets are not supplied due to the wide range which would
be necessary to meet all requirements. Busbar cable clamps comprise plated brass U-clamps
and steel slides with all bolts and washers. They are suitable for the connection of small
solid or stranded copper conductors and also aluminium conductors using a barrier grease.
Busbar cable sockets are plated brass castings complete with clamps and fixings, suitable
for the termination of either copper or aluminium conductors. Both clamps and sockets
allow for clamping on the busbars without drilling. For cabling direct on to busbars of 630
800A rating a special cable extension is required which can be made to special order.
Switchgear mounting sets

Available for all ratings of Exel switch-disconnectors/switchdisconnector fuses and Glasgow
fuse-switch disconnectors and switchdisconnectors enabling these units to be mounted
simply and efficiently either above or below the busbar chamber. Each mounting set
comprises a template with instructions for machining the top/bottom plate of the busbar
chamber; clamping channels, ready pierced for fasteners; all necessary fastenings; and,
for Glasgow units, insulated shields and switch filler plates where appropriate.

Product overview
Exel 2 switch-disconnectors & switch-disconnector fuses

Exel 2 switch disconnectors and switch-disconnector fuses meet the constructional requirements
for isolation of and are type tested to BS EN 60947-3. Switches are of the quick make and break
type, suitable for use on AC or DC. Units have removable moving contact assemblies to facilitate
wiring. Exel 2 surface-mounting enclosures are fabricated from rust-protected sheet steel with a light
grey paint finish. Removable blank top and bottom end plates (except for 20 and 32A top end plates
which incorporate knockouts) and gasket doors give IP41 protection. Chromium-plated front operated
handles, with ON (I) OFF (O) indication, and internal fixing enabling units to be mounted closely
side by side. Interiors comprise porcelain bases fitted with non-ferrous conducting components.
Fuses and fuse carriers

HRC fuse carriers are designed for offset contact fuse links to BS 88: Part 2. Eaton HRC fuse links
fitted to switchdisconnector- fuses are suitable on systems up to 415V AC. Eaton fuses used in
these products are also suitable for 250V DC systems. All performance tests have been carried out
using Eaton BS88 fuselinks. Units are fitted with HRC Fuselinks of maximum rating but will accept
fuselinks of a lower rating, refer to the Paramount HRC Fuselinks section on page 101. HRC pattern
switchfuses are fitted with type SCH carriers (20A, 32A, 63A-moulded; 100A, 125A-porcelain).
Motor ratings
The motor ratings assigned to TPN switch-disconnector units are utilisation category AC23A
(frequent operation) to BS EN 60947-3, which calls for make and break testing at 10 and 8
times rated current respectively for units having a motor rating up to and including 100 Amps.
Ratings for switch-disconnector-fuses are dependent on suitable HRC fuses being fitted.
Cable size
Maximum cable sizes are: 20A6mm2, 32A10mm2, 63A35mm2, 100/125A70mm2.
Type test compliance with standards

This range has been satisfactorily type-tested in accordance with
BS EN 60947-3 with Eaton HRC fuselinks fitted.

Rotary isolators
Local switch-disconnectors standard duty, 2063A, IP65, 3, 3+N, 6, and 8 poles

Complying with IEC/EN 60947-3, VDE 0660, and IEC/EN 60204, the surface
mounting range of rotary switch disconnectors are suitable for on load switching of
general distribution a.c. power circuits and infrequent duty motor isolation.
Light grey, moulded silicon and halogen free thermoplastic enclosures provide protection
to IP65 making them suitable for most indoor and outdoor environmental conditions.
These compact isolators are fitted with red/yellow operating handles
padlockable in the OFF position with up to three padlocks.
The enclosure design allows for easy access for cabling. Solid neutral
and earth termination points are a standard feature.
Changeover switches
20-100A, IP65, 4 pole

Suitable for on-load control of alternative supplies. Surface mounted, 4
pole on-load changeover switches have a rated voltage of 690V.
Switches comply with IEC/EN 60947-3, VDE 0660, IEC/EN 60204.
In all cases ample cable space is provided for both incoming and outgoing cables.
Each unit is provided with an insulated IP65 black handle which may be padlocked
in the OFF position. Clear ON (I) and OFF (O) indication is provided.

Product overview
Exel distribution fuseboards
The Exel fuseboard range is available with standard enclosures to IP4X for the complete range of 20A
to 200A distribution boards. A variety of extra features have been incorporated in the range including
increased cabling space, superior door latches and locking devices (there is a choice of barrel lock
or padlocking device), improved lid hinges and a unique safety carrier which effectively blanks off a
single fuse-way allowing the circuit to be worked on in safety. Safety carriers have no provision for
accepting a fuselink. The Exel distribution fuse boards are designed to comply with the requirements
of BSEN 61439-2. All phase parts are fully shrouded so that additional circuits may be wired and
connected in safety whilst the existing circuits remain live and on load. The type of enclosure available
gives protection to IP4X and is supplied with removable endplates. The range covers a wide variety
of ratings from 20200A; 20A and 32A with up to 12 ways in SPN and TPN configurations; 63A up to
8 ways, 100A up to 8 ways and 200A 4 way in TPN configurations. All ratings available with moulded
HRC carriers to BS88: Part 2. Testing has been carried out using Eaton S type HRC fuselinks. Fuse
base mouldings are of high quality thermosetting material. The fuse units have skirted fuse carriers to
prevent accidental contact with live parts when inserting or withdrawing a carrier. Separate shields are
provided for the base contacts to prevent accidental contact when the carrier has been withdrawn.
All fuseboards are suitable for systems with a rated insulation voltage Ue 660V AC, 500V DC.
Safety carriers
A range of safety carriers are available for insertion in a fusebase when its normal
fuse carrier has been removed for isolation. The safety carriers are marked
yellow for identification and have no provision for fuselink fixing.
Enclosures
Rust protected sheet steel IP4X enclosures have a light grey paint finish and are fitted with internal
fixing holes. Enclosures have a robust, reliable construction. Enclosures for units from 20A to
100A are of all welded construction, 200A IP4X units have cast corner pieces. Removable top
and bottom endplates incorporate knockouts on 20A and 32A units while 63200A boards have
blank endplates. Blank endplates are available on request for 20A and 32A boards. The enclosure
allows gasketed access doors to be reversed for left hand or right hand opening. All sides are
free from external projections and fuseboards can be mounted in inverted form if required.
Main terminations
32A, 2-way fuseboards have the main phase termination (tunnel type) attached to the fusebanks.
All other fuseboards have the main terminations mounted on the back of the enclosure and are
intended for use with cable sockets (sweating or crimp type) which are not provided. Busbar
and main terminals are fully shrouded. A cable shroud to cover the cable socket is provided.
Earthing and neutral bars

Multi-way earthing bars are fitted with an integral earth bolt and have an outgoing terminal per fuse.
They are rail mounted adjacent to the fully rated neutral bars. Neutral bars have main terminals of
the same capacity as the phase terminals and have one outgoing terminal per fuse. Earth/neutral bar
rails are fitted at the bottom of enclosures on 20A and 32A fuseboards and at the top on all others.

HRC cartridge fuselinks, carriers and bases

Eatons comprehensive range offers a selection of fuses to cater for many applications:
Compact 415V a.c. S type industrial fuselinks complying with BS EN 60269-1 (BS88
1) or BS88 2 with ratings from 2 to 1250A. Skilful design techniques have meant
that power dissipation has frequently been reduced despite the significant reduction in
barrel size. Many ratings have also been tested for use in circuits up to 250V d.c.
Compact 415V a.c. S type motor circuit protection fuselinks complying with BS EN 60269-1 (BS88
1) or BS88 2 with ratings from 20M25A to 400M500A. This extended range of fuselinks is
designed to withstand the inrush current associated with direct on line start motors whilst saving
cost on the size of equipment to which they are fitted by virtue of their small dimensions.
Compact 240V and 415V a.c. SS, SN and SP type offset blade contact
fuselinks complying with BS EN 60269-1 (BS88 1) or BS88 6 with ratings
from 2 to 63A for use in industrial and commercial installations.
Compact 415V a.c. J type feeder pillar fuselinks complying with BS88 2 (formerly BS88:
Part 5) for use by the Electricity Supply Industry in distribution systems. Ratings from
63400A with 82mm fixing centres and 63800A with 92mm fixing centres for wedge
tightening contacts and 63250A in ferrule form for single phase pole mounted cut outs.
Eaton HRC fuselinks are manufactured to exacting standards using precision assembly methods
and undergo rigorous quality checking before dispatch including resistance testing all production.
This ensures that performance will be consistent and conform with published characteristics within
close tolerances. Type tests on Eaton equipment have been performed using Eaton fuselinks.
Eaton industrial and general purpose fuselinks have a breaking range and utilisation
category gG which replaces the old class Q1 fusing factor. g indicates a full range
breaking capacity fuselink and G indicates a fuselink for general application.
Eaton motor circuit protection fuselinks have a breaking range and utilisation category
gM indicating a full range breaking capacity fuselink for the protection of motor
circuits. These fuselinks have a dual current rating separated by the letter M.
The lower current rating is the maximum continuous rating which also determines the rating
and size of equipment to which the fuse is fitted. The higher current rating is the time current
characteristic of the fuselink which determines its ability to withstand the motor starting current.
Their selection frequently permits the use of lower rated switch and/or fusegear than would be
the case using gG fuselinks with a consequent cost saving. Type gG fuselinks however may still be
used and are the preferred option for assisted start motors where starting currents are reduced.
Eaton fuselinks are designed and manufactured in accordance with a Quality Management
System in accordance with ISO 9001. Most fuselinks are ASTA Certified for a breaking
capacity of 80kA at 415V a.c. and are endorsed ASTA 20 CERT showing compliance
with the rules of the ASTA 20 scheme which includes assessment of the Quality
Management System to ISO 9002 and detailed auditing of fuselink manufacture.
Eaton have for many years participated in developing and influencing fuse standards
through BEAMA and BSI at national level and IEC at international level and therefore
are able to produce designs incorporating forthcoming changes to standards.

Product overview
Fuse carriers and bases specification
A range of moulded HRC fuse units designed to accept bolt-in and clip-in HRC fuselinks.
Each unit is fully shrouded to prevent accidental contact with live parts when inserting
or withdrawing a carrier and once the carrier has been removed completely.
The carrier and base mouldings are manufactured from high quality thermosetting material.
Units accepting bolt-in HRC fuselinks are available in ratings of 20, 32,
63, 100 and 200A and can be supplied in front connected, front/busbar
connected, front/back connected and back connected versions.
They are designed to comply with BS88 2 and are suitable for systems up to 660V.
Suitable HRC fuselinks are also to BS88 2. A full range of neutral links is available.
Those units which accept the clip-in fuselinks are rated at 32A and 63A, 415V.
They comply with BS88 2 and accept clip-in HRC fuselinks to the same standard.
Clip-in type units allow fuselinks to be replaced very simply no tools are
required. Fuselinks are removed from the carrier using side pressure on the
fuselink end tags while replacement involves a simple push fit only.
Terminal capacities: 20A 6mm2, 32A 16mm2, 63A 35mm2, 100A 70mm2, 200A 150mm2.
Fuse units are available in four types:
Type A providing for busbar connection at one end and cable termination at the other.
Type B providing for cable connection at each end.
Type C with back connecting studs.
Type D providing for cable connection at one end with back connecting stud at the other.
Fuse units have been ASTA certified to BS88 2 and are suitable for systems up to 660V.
100A fuse units may be fitted with SB3, SB4 or S0 fuselinks having
73mm fixing centres if used with adaptor 100MFLK.

Enclosed motor, heating and lighting control
Eatons wide range of Motor Control Gear and Heating and Lighting Control
equipment is an integral part of our single source commitment.
Since the late 1920s we have built countless motor starters, fitted and trusted by generations of
contractors, while the increasing requirements of our markets have led us to constantly update and
expand our ADS range to allow for an increased choice of current ratings and ingress protection.
This wealth of experience and expertise in the design and manufacture of Motor Control Gear is
mirrored by our Heating and Lighting range which offers a versatile and comprehensive choice.
Standards
IEC 60947-4-1
VDE 0660
IEC 60269
BS EN 60947-4-1
ADS8 AC motor starters
Enclosures moulded
9kW DOL max
Tough polycarbonate in grey provides high IP protection to IP65
Start and stop pushbuttons
Internal earth terminals
Cable entries 20mm knockouts for M20 threaded glands
Enclosures metalclad
Attractively styled rust protected pressed steel finished in grey polyester powder paint
Start and mushroom-headed stop pushbuttons
Substantial earth terminal
Cable entries 20mm knockouts for M20 threaded glands
Switch-disconnectors
Means of isolation and switching for mechanical maintenance
Padlocking facility available
Isolators type tested for on-load disconnection
Interlocked with main cover
Overload relays
Adjustable thermal pattern connected directly to contactor
Ambient temperature compensated between -40C to +60C
Phase failure sensitive relays
Changeover trip contact
Simple Auto-reset
Contactors
Modern block type
615 x 106 mechanical and 1.5 x 106 electrical operations AC3 duty.
Provisions for fitting additional auxiliary contacts either N/O or N/C depending on version
Optional fittings and specials

Provision for various optional fitments on standard starters
Special starter arrangements

Product overview
Enclosed motor, heating and lighting control 1.10
MSU pushbutton control units
The Push Button Units are supplied with robust plastic enclosure
to IP67, in one, two and three push button types.
Complies with IEC/EN 60947-5
Simplicity, versatility and robust construction successfully allied to attractive styling
One, two and three button types available in a variety of configurations
3-button type M23MSUL supplied with 2 sets of button legends, FORWARD, REVERSE
and UP, DOWN. The required legend should be clipped onto the button as required
Each contact block comprises 1 N/O and 1 N/C contact
Start units are push to make (N/O)
Stop units are push to break (N/C)
Latching device where fitted holds stop pushbutton in depressed position
until latch is released by clockwise rotation of mushroom head.
Various conduit knockout options on side and rear of enclosures
Autoline heating and lighting contactors
Open contactors
18A, 25A and 32A, 4-pole, with optional auxiliary contacts
Enclosed contactors
25A and 40A, 4-pole; 40A and 64A, 2-pole; 70A and 112A, single pole with fitted neutral link
Robust pressed steel enclosures, rust protected with grey paint finish
220240V units available with or without rectifiers for silent running
90-225A, 3-pole enclosed contactors can be supplied with switch-
disconnector-fuse including HRC main fuses

Power factor correction capacitors

Active power
How can you economise? Reactive power
A great deal of money is spent annually to achieve savings in
production methods, improved plant efficiency and optimum
lighting arrangements; essential in the highly competitive world
of industry today. However, poorly managed energy supplies
result in unnecessary, and avoidable wastage. Power factor
correction is the established method of reducing electricity costs
in industry and commerce. You can eliminate waste in electricity
consumption by improving your power factor and saving up to
20% on your electricity costs. This could also help you to increase
your output without the need to install new cables or extra supply SUPPLY MOTORS
capacity. To find out more contact us for a power factor check.
What is power factor correction? Active power
Most loads on an electrical distribution system fall into one of Reactive power
three categories; resistive, inductive or capacitive. In your own
plant, the most common is likely to be inductive. Typical examples Available active
of this include transformers, fluorescent lighting and AC induction power
motors. Most inductive loads use a conductive coil winding to
produce an electromagnetic field, allowing the motor to function.
All inductive loads require two kinds of power to operate:

Active power (kwatts) to produce the motive force
Reactive power (kvar) to energise the magnetic field
SUPPLY MOTORS CAPACITOR
The operating power from the distribution system is composed
of both active (working) and reactive (non-working) elements. leaving the capacitor working at a slightly lower output. Over
The active power does useful work in driving the motor the years, your capacitors could have lost so much output that
whereas the reactive power only provides the magnetic field. you could be paying the penalty for a poor power factor.
The bad news is that you are charged for both! Our engineers would be pleased to carry out a test on your
installation to determine whether it is running economically.
The objective, therefore, should be to reduce the reactive
power drawn from the supply by improving the power factor. As the power factor drops the system becomes
less efficient. A drop from 1.0 to 0.9 results in 15%
If an AC motor were 100% efficient it would consume only
more current being required for the same load.
active power but, since most motors are only 75% to 80%
efficient, they operate at a low power factor. This means poor A power factor of 0.7 requires approximately 43% more
energy and cost efficiency because the Regional Electricity current; and a power factor of 0.5 requires approximately
Companies charge you at penalty rates for a poor power factor. 100% (twice as much) to handle the same load.
By installing capacitors to improve your power factor
you could SAVE MONEY on your electricity bill. Do you have a problem with harmonics?
If you have
Additional potential benefits include:
Nuisance tripping of circuit breakers or fuses blowing
Reduction of heating losses in transformers Erroneous operation of control system equipment
and distribution equipment
Electronic communication interference
Longer plant life
Excessive heating and failure of transformers, motors,
Stabilised voltage levels capacitors, fluorescent lighting ballasts etc.
Increase in capacity of your existing system and equipment Excessive neutral current
Improved profitability you could have a harmonic problem.
What do I have to do to save money? Our engineers will be pleased to check this for you.
Simply contact us on +44(0)121 685 2011 and we will arrange 200

for an engineer to carry out a power factor survey. This will
be done quickly, with no interruption to your operations and
with absolutely no obligation on your part. We shall then
% Current
be able to advise you of the savings you can achieve which

150
could be as much as 20% of your current electricity bill.
Do you need to take action if you already have capacitors?

Modern capacitors are made of metallised polypropylene film. 100
If they develop a fault, then instead of the whole capacitor 1 0.9 0.8 0.7 0.6 0.5
failing, only a small section of the metallisation burns away, Power factor COS

Product overview
Power factor correction capacitors 1.11
Eaton capacitors non-auto range
The Eaton non-auto range of capacitors is designed for individual correction of motors,
transformers and other items of plant. The capacitors are manufactured in robust
steel cases suitable for the work place. They can be supplied with open terminals for
mounting within cubicles or other switchgear or with fully enclosed terminals for use
elsewhere. Single or three phase units are available in a wide range of sizes.
Low loss Self healing Non flammable Easily maintained Environmentally friendly
Eaton capacitors non-auto application

Most AC electrical machines draw from the electricity supply apparent power in excess of the useful
power required by the machine. By connecting the Eaton capacitor into circuit, it is possible to reduce
the excess current. This saves energy and makes the most efficient use of your electricity installation.
Eaton capacitors non-auto construction

The capacitor consists of a number of low loss self healing elements assembled
in a robust steel case which is suitable for the work place.
Protection system
Each element is fitted with a protection system which ensures an
extended capacitor life and complete end of life safety.
Elements are self healing and have an over pressure double pole automatic
disconnect feature that ensures that if the element fails it is electrically safe.
Capacitor features
Low loss less than 0.5 Watts per kvar, including discharge resistors.
Environmentally safe The dry type construction eliminates flammable
impregnants and does not cause leakage or pollution problems.
Eaton capacitors 100

The Eaton 100 range of capacitors is designed for the automatic power factor correction
of industrial loads. The capacitors are manufactured in robust steel cases suitable for the
work place. The equipment is arranged to switch capacitors as the load requirement varies,
thus ensuring that the system power factor is maintained at an economic level.
Low loss Self healing Non flammable Easily maintained
Environmentally friendly Fully automatic control
Eaton capacitors 100 application

Most AC electrical machines draw from the electricity supply apparent power in excess of the useful
power required by the machine. By connecting the Eaton capacitor into circuit, it is possible to reduce
the excess current. This saves energy and makes the most efficient use of your electricity installation.
Eaton capacitors 100 construction

The capacitor consists of a number of low loss self healing elements
assembled in a robust steel case which is suitable for the work place. Each
unit is available with a fusebase/fuseswitch or MCCB incomer.
Protection system
Each element is fitted with a protection system which ensures an
extended capacitor life and complete end of life safety.
Elements are self healing and have an over pressure double pole automatic
disconnect feature that ensures that if the element fails it is electrically safe.
Capacitor features
Low loss less than 0.5 Watts per kvar, including discharge resistors.
Environmentally safe The dry type construction eliminates flammable
impregnants and does not cause leakage or pollution problems.

Eaton capacitors 300 standard

The Eaton capacitors 300 cubicle is designed for the automatic power factor correction of industrial
loads. It can be supplied with a reactive sensing relay or arranged to operate from existing
control devices (slave). The equipment is arranged to switch capacitors as the load requirement
varies, thus ensuring that the system power factor is maintained at an economic level.
Fully automatic control Easily extendable Low loss Selfhealing
Individually protected elements Non flammable construction
Environmentallyfriendly Easy maintenance Front or rear cable access
The cubicle is designed to be compatible with switchboards, its construction, therefore,
is to the same exacting standards required by a switchboard manufacturer.
Hinged doors are fitted as standard which permits easy inspection and maintenance.
The equipment is designed for full front access both for installation and
maintenance. It can, therefore, be fitted where space is at a premium.
The modular body construction as standard, enables the equipment
to be easily extended at a later date if required.
The cubicle incorporates capacitor units
with the following features:
Dry long life low dielectric loss.
Metallised polypropylene windings encapsulated in epoxy
resin and mounted within a sheet steel case.
Fitted with an internal fuse.
Self-healing internal faults vaporize the metallisation.
Low losses less than 0.5 W/kvar.
Environmentally friendly, non-toxic and non-flammable.
Complete with discharge resistors.
Cubicle construction
Each Eaton capacitors 300 cubicle can house up to 300 kvar of capacitors
switched in stages of 25 to 100 kvar dependent upon requirements.
The control equipment comprises:
Set of DIN removable fuses and carriers per 1 or 2 switching stages.
Suitably rated contactor per switching stage.
Hand/Off/Auto selector switch per switching stage when required.
Capacitor Energised indication lamp per switching stage when required.
Set of control fuses.
The cubicle has throughgoing busbars and all internal wiring and
interconnections. Control wiring is clearly labelled.
All switching stages are clearly numbered and the panel is
complete with all necessary information labels.

Product overview
Eaton capacitors 300 detuned
The Eaton capacitors 300 cubicle is designed for the automatic power factor correction of
industrial loads. It can be supplied with a reactive sensing relay or arranged to operate from
existing control devices. The equipment is arranged to switch capacitors as the load requirement
varies, thus ensuring that the system power factor is maintained at an economic level.
De-tuned to reduce harmonics Reduced nuisance tripping of MCCBs
Fullyautomatic control Easily extendable Low loss Selfhealing
Individually protected elements Nonflammableconstruction
Environmentallyfriendly Easy maintenance Front or rear cable access
The cubicle is designed to be compatible with switchboards, its construction, therefore,
is to the same exacting standards required by a switchboard manufacturer.
Hinged doors are fitted as standard which permits easy inspection and maintenance.
The equipment is designed for full front access both for installation and
maintenance. It can, therefore, be fitted where space is at a premium.
The modular body construction as standard, enables the equipment
to be easily extended at a later date if required.
The cubicle incorporates capacitor units

with the following features:
Dry long life low dielectric loss.
Metallised polypropylene windings encapsulated in epoxy
resin and mounted within a sheet steel case.
Fitted with an internal fuse.
Self-healing internal faults vaporize the metallisation.
Low losses less than 0.5 W/kvar.
Environmentally friendly, non-toxic and non-flammable.
Complete with discharge resistors.
Cubicle construction
Each Eaton capacitors 300 cubicle can house up to 250 kvar of
capacitors switched in stages of 25 to 100 kvar dependent
upon requirements.
The control equipment comprises:

Set of DIN removable fuses and carriers per switching stage.
Suitably rated contactor per switching stage.
Hand/Off/Auto selector switch per switching stage when required.
Capacitor Energised indication lamp per switching stage when required.
Set of control fuses.
Natural ventilation is deemed acceptable, however forced ventilation is available on request.
The cubicle has throughgoing busbars and all internal wiring and
interconnections. Control wiring is clearly labelled.
All switching stages are clearly numbered and the panel is
complete with all necessary information labels.
Reactor details:
Aluminium or Copper windings (on request, dependant on customer specification).
Low losses.
Low noise.
High overloading capacity.
7% de-tuning factor as standard, others available on request.
189Hz as standard.

What are harmonics?

Harmonic distortion in electrical power systems is becoming more and more prevalent.
The ever increasing use of devices having non-linear operating characteristics
means more harmonics are being produced in the power system.
This section looks at the problems this is causing and the solutions
that can be achieved by the use of Eaton capacitors.
Harmonic problems must not be confused with transient disturbances. Harmonics
are continuous, steady state disturbances whereas transient disturbances
are of short duration caused by spikes, surges, or impulses.
For most electrical engineering applications it is assumed that all
alternating currents and voltages have a sinusoidal waveform.
An alternating waveform that is not sinusoidal is said to be complex. This complex
waveform may be shown to be built up of a series of sinusoidal waveforms whose
frequencies are integral multiples of a frequency of the fundamental, or basic, wave.
The sinusoidal components of a complex wave are called the harmonics.
Thus the second harmonic has a frequency of twice the fundamental, the third three times, etc.

Memshield 3 MCB distribution boards and enclosures
2
Eatons Memshield 3 MCB distribution boards have

evolved through an intimate knowledge and feedback
from electrical contractors, consulting engineers
and end users to provide solutions to a wide range
of electrical distribution applications in commercial
buildings. Memshield 3 delivers safe, reliable and
high performance protection of electrical power
distribution systems in accordance with BS EN 61439.
2.1 TYPE A SPN DISTRIBUTION BOARDS
125A SPN, type A distribution boards......................................................................................................................................... 32
Incoming devices ........................................................................................................................................................................ 32
Meterpack assemblies ................................................................................................................................................................ 32
Surge protection devices ............................................................................................................................................................ 32
Outgoing devices, MCBs & RCBOs ........................................................................................................................................... 33
General accessories ................................................................................................................................................................... 34
2.2 TYPE B TPN DISTRIBUTION BOARDS
125A TPN, type B distribution boards ......................................................................................................................................... 35
125A Incomer kits ...................................................................................................................................................................... 35
250A TPN, type B distribution boards ......................................................................................................................................... 35
250A Incomer kits ...................................................................................................................................................................... 36
Meterpack assemblies ................................................................................................................................................................ 36
Split metered power and lighting board ..................................................................................................................................... 36
Surge protection devices ............................................................................................................................................................ 36
Outgoing devices, MCBs & RCBOs ........................................................................................................................................... 37
General accessories ................................................................................................................................................................... 40
2.3 MODULAR ENCLOSURES
Enclosure accessories ................................................................................................................................................................ 41
2.4 MCB PAN ASSEMBLIES............................................................................................................................................................ 42

2.1 Memshield 3 MCB distribution boards and enclosures
Type A, SPN distribution boards
See page 126 for technical data and overall dimensions
EAM10 125A SPN, type A distribution boards

When more than 16 SP ways are required, see our TPN board ranges, complete with single phase kit options
IP3X
Description Rating Total no. of Eaton list
(A) outgoing ways number
4 way SPN, type A distribution board 125 4 EAM4

EAMS1251N Incoming devices for SPN, type A distribution boards

Incoming devices supplied separate to distribution board
Description Rating Poles Sensitivity Eaton list
(A) (mA) number
Switch-disconnector 125 SPSN EAMS1251N

RCCB incoming device for SPN, type A distribution board 90 1P+N 30 EAMS100HE
RCCB incoming device for SPN, type A distribution board 90 1P+N 100 EAMS100ME
RCCB incoming device for SPN, type A distribution board 90 1P+N 300 EAMS100LE
Direct connection kit for SPN, type A distribution board 100 1P+N EAMBT1002
EAMMP65 Metered SPN, type A distribution boards & standard meter packs
Type A SPN boards, fitted with multifunction meters, can display; Amps, kW, kWh, kVar
and kVarh pulsed output etc.
Split load versions utilise a two channel meter, feeding two independent busbars and groups of MCB/RCBOs
Split load versions provide independent monitoring of Power and Lighting loads and total load.
Aids compliance with Part L2 of the building regulations (England & Wales and Section 6 Scotland)
IP3X
Description Rating Total no. of Installed meter, Eaton list
(A) outgoing ways characteristics3) number
Meterpack for SPN, type A distribution boards 65 Pulsed output, kWh EAMMP65
9 way SPN, type A distribution board1) 65 9 Pulsed output, kWh EAM9M
9 way SPN, type A distribution board1) 65 9 Modbus EAM9MB
12 way SPN, type A distribution board1) 65 12 Pulsed output, kWh EAM12M
12 way SPN, type A distribution board1) 65 12 Modbus EAM12MB
Split metered SPN, type A distribution board1), 2) 100 9 + 3 Pulsed output, kWh EAMSL93M
Split metered SPN, type A distribution board1), 2) 100 9 + 3 Modbus EAMSL93MB
Split metered SPN, type A distribution board1), 2) 100 6 + 6 Pulsed output, kWh EAMSL66M
Split metered SPN, type A distribution board1), 2) 100 6 + 6 Modbus EAMSL66MB
1) Includes factory fitted switch disconnector and single channel meter
2) Includes two channel meter, 65A max load per channel
3) Output type is Pulsed or Modbus
EM3SSK1T2 Surge protection device for SPN, type A distribution boards

See page 126 for technical data
Description Eaton list
number
Enclosed surge protection kit for SPN boards type 2 EM3SSK1T2

Type A, SPN distribution boards 2.1
EMDH104 Outgoing devices, MCBs 10/15kA, single pole
Trip types B, C and D
Dual rated, 10kA to IEC 60898 and 15kA to IEC 60947-2
Description Rated Width Short circuit Eaton list number
current (A) (mm) rating (kA) Trip type B Trip type C Trip type D
Miniature circuit breaker 1 18 10/15 EMBH101 EMCH101 EMDH101

Miniature circuit breaker 50 18 10/15 EMBH150 EMCH150 EMDH1501)
1)
15kA to IEC60947-2 rating only
EMCH116R30C Outgoing devices, RCBOs single pole trip type C 30mA sensitivity
Eatons range of residual current circuit breakers with integral overload protection (RCBOs), are manufactured to IEC/
EN 61009 and meet the latest European and international standards.
For other RCBO sensitivity options refer to full details on page 49.
Description Rating Trip type Sensitivity Eaton list
(A) (mA) number
Eaton RCBO 6A 10kA type C SP 6 C 30 EMCH106R30C

EMBH116R30C Outgoing devices, RCBOs single pole trip type B 30mA sensitivity
(A) (mA) number
Eaton RCBO 6A 10kA type B SP 6 B 30 EMBH106R30C


Type A, SPN distribution boards
EMDL General accessories for SPN, type A distribution boards

number
MCB blanking module 18mm EMBP

Half MCB blanking strip 9mm EMABP
Universal device lockout attachment fits MCBs, RCCBs and RCBOs ASPDL
Padlock suitable for ASPDL PD2
EMPL
Door barrel lock with 2 keys EMDL
Door padlocking kit EMPL
Padlock suitable for EMPL PD1
Vertical coupling kit for connecting 2 SPN Distribution boards (125A max. total load)1) EAMCK
Clean earth for A board 5 terminals EAME5
Clean earth for A board 11 terminals EAME11
1) Incominging device required for each linked distribution boards

Type B, TPN distribution boards 2.2
EBM81 125A/250A TPN, type B distribution boards

IP4X
4 way TPN, type B distribution board 125 4 EBM41

12 way TPN, type B distribution board 125/2251) 12 EBM122
1)
225A/250A options if used with cable extension box or with cable trunking. See 250A incomer options below
125A SPSN, type B distribution board

EBM121D
SPSN main switch disconnector fitted
IP4X
12 way SPSN type B distribution board 125 12 EBM121D
EBMS1253 125A incomer options for type B distribution boards

Incoming devices supplied separate to distribution board.
Description Rating Pole Eaton list
(A) configuration number
Switch disconnector 125 TP EBMS1253

Switch disconnector kit (including single phasing link) 125 SPSN EBMS1251N
Switch disconnector 125 TPSN EBMS1253N
Direct connection (lugs connector) 125/250 TP EBMBT2503
30mA RCCB1) 100 TPSN EBMR30
300mA RCCB with time delay 100 TPSN EBMR300T
Switch disconnector feeding 125A TP AC1 contactor, housed in extension box 125 TP EBMCC1253
1)
Includes 50mm2 terminal adapter
EBM62H 250A TPN, type B high load distribution board

These boards include 2 TPN outgoing ways for 27mm MCB (upto 125A)
Adequate integral cabling space means that no extension box is required.
IP4X
Fitted with door lock as standard.
Description Rating Total no. of 18mm Total no. of 27mm Total no. of Eaton list
(A) TP outgoing ways TP outgoing ways outgoing ways number
(63A max) (125A max)
2 way TPN, type B distribution board 200 0 2 2 EBM22H

Type B, TPN distribution boards
EBMMB250 250A incomer options for type B distribution boards

Incoming devices supplied separate to distribution board.
Where used with EBM122 or EBM242, a separate cable extension box or suitable cable trunking is required

Switch-disconnector 250 TP EBMS2503

Direct connection (lugs connector) 250 TP EBMBT2503
MCCB incomer kit (includes MCCB) 250 TP EBMMB250
Switch disconnector feeding 250A TP AC1 contactor, housed in extension box 250 TP EBMCC2503
Single phase conversion kit for 250A rated board only (requires EBMS2503 to be ordered seperately) EBMS25
EBMMPCT250 Meterpack assemblies TPN, type B distribution boards

Description Rating (A) Installed meter, Eaton list
(total load) characteristics number
Meterpack for TPN, type B distribution boards 250 Pulsed output, kWh EBMMPCT250
Meterpack for TPN, type B distribution boards 250 Modbus + pulsed output, kWh EBMMPCT250M
Meterpack for TPN, type B distribution boards 250 MID certified meter EBMMPCT250MID
Double meterpack for 2 x TPN, type B distribution boards 250 Pulsed output, kWh EBMMPSL250
Double meterpack for 2 x TPN, type B distribution boards 250 Modbus + pulsed output, kWh EBMMPSL250M
Double meterpack for 2 x TPN, type B distribution boards 125 Pulsed output, kWh EBMMPSL125
Double meterpack for 2 x TPN, type B distribution boards 125 Modbus + pulsed output, kWh EBMMPSL125M
Meterpack for TPN, type B distribution boards 120 MID certified meter EBMMPDC120
EBMSL642MB Split metered power and lighting board 200A TPN, type B
Includes factory fitted 200A switch disconnector and two channel meter
Adequate integral cabling space means that no extension box is required.
IP4X
Meter has both pulsed and Modbus outputs as standard.
Fitted with door lock as standard.
Single phasing kit included to be used if required
Description Rating Total no. of Installed meter, Eaton list
(A) outgoing ways characteristics number
Split metered TPN, type B distribution board 200 6+4 Modbus + pulsed output, kWh EBMSL642MPMB
EM3SSK3T12 Surge protection device for type B distribution boards

number
Enclosed surge protection kit for TPN boards type 1&2 EM3SSK3T12
Enclosed surge protection kit for TPN boards type 2 EM3SSK3T2

EMDH104 Outgoing devices MCBs 10/15kA, single pole
Miniature circuit breaker 1 18 10 /15 EMBH101 EMCH101 EMDH101

Miniature circuit breaker 50 18 10 /15 EMBH150 EMCH150 EMDH1501)
Miniature circuit breaker 63 18 10 /15 EMBH163 EMCH163 EMDH1631)
1)
EMCH310 Outgoing devices MCBs 10/15kA, three pole


1)
EMCS1100 Outgoing devices (for 250A high load distribution board only) MCBs, single pole
Rated current Width Short circuit rating Eaton list number
In (A) (mm) (IEC/EN 60947-2) Trip type B Trip type C Trip type D
20 27 25kA EMBS120 EMCS120 EMDS120

100 27 20kA EMBS1100 EMCS1100 EMDS1100
125 27 15kA EMBS1125 EMCS1125

EMCS3125 Outgoing devices (for 250A high load distribution board only) MCBs, three pole
Rated current Width Short circuit rating Eaton list number
In (A) (mm) (IEC/EN 60947-2) Trip type B Trip type C Trip type D

100 81 20kA EMBS3100 EMCS3100 EMDS3100
125 81 15kA EMBS3125 EMCS3125
EMCH116R30C Outgoing devices, RCBOs single pole trip type C 30mA sensitivity
Eatons range of residual current circuit breakers with integral overload protection (RCBOs), are manufactured to IEC/
EN 61009 and meet the latest European and international standards.
For other RCBO sensitivity options refer to full details on page 49.
(A) (mA) number

EMBH116R30C Outgoing devices, RCBOs single pole trip type B 30mA sensitivity
(A) (mA) number


169639 Outgoing devices, 10kA 3P +N RCBOs
Conditionally surge current-proof 250A.
Sensitivity type A, providing protection against AC and pulsating DC earth fault currents.
Trip types B, C, and D
Trip sensitivity 30mA, 100mA or 300mA
Description Rating Sensitivity Type designation Eaton list
Characteristic B (A) (mA) number
3P+N RCBO 10A 10kA trip B 10 30 mRBM4-10/3/B/003-A-UK-PT 169636

Characteristic C (A) (mA) number
3P+N RCBO 6A 10kA trip C 6 30 mRBM4-6/3/C/003-A-UK-PT 169640
3P+N RCBO20A 10kA trip C 20 30 mRBM4-20/3/C/003-A-UK-PT 169644
Characteristic D (A) (mA) number
3P+N RCBO 6A 10kA trip D 6 30 mRBM4-6/3/D/003-A-UK-PT 169647

EMBP General accessories, type B

number
MCB blanking module 18mm EMBP

MCB blanking module 27mm EMBPH
EBMTK Universal device lockout attachment fits MCBs, RCCBs and RCBOs ASPDL
Lockout attachment for 27mm MCBs ASPDL27
Lockout attachment for 250A switch/MCCB 131669
Shunt trip 230-240V AC for 250A switch/MCCB 158056
Undervoltage release 230240V AC for 250A switch/MCCB 158053
Padlock suitable for ASPDL & ASPDL27 PD2
Top/bottom gland plate EBMGP4
IP42 gland plate kit EMGP142
Cable trunking interface kit EBMTK
Spare way label 12 way pack of 5 EBLB1
Spare way label 18 way pack of 5 EBLB2
Enclosure for NZM1 3-pole MCCB incomer EBMMBKIT
EBMXPC1 Cable extension boxes, type B

Description Box Eaton list
height number
Cable spreader extension box 180mm EBMXPC1

Cable spreader extension box 250mm EBMXPC2
EBMNE8 High integrity/clean earth kit

Description No. of Eaton list
ways number
High integrity/clean earth kit for type B Board 8 EBMNE8

Note: Up to 4 high integrity earth bars can be fitted to a type B distribution board

EBMXDC9 Modular enclosures
Modular enclosures will accept MCBs, RCCBs, RCBOs, fuse modules and command control products.
Modular enclosures EBMXDC6 to EBMXDC45 are fitted with earth and neutral bars as standard.
Modular enclosures EBMXDC15 and EBMXDCG15 have same profile width suitable for mounting
onto type A, SPN distribution board EAM13 or any type B, TPN distribution board.
See page 127 for technical data and overall dimensions.
Description Capactiy in Glazed door Eaton list
18mm modules number
Modular enclosure, 15 module din rail glazed door 15 Yes EBMXDCG15

Modular enclosure, 6 module din rail unglazed door 6 No EBMXDC6
Modular enclosure, 2 x 15 module din rail unglazed door 30 No EBMXDC30
Modular enclosure, 3 x 15 module din rail unglazed door 45 No EBMXDC45
EBMXE15 Enclosure accessories

number
Additional earth bar (15 additional holes) EBMXE15

Distribution boards type A and type B cable capacities

Cable capacities Type A Type B
125A switch disconnector 50mm2 50mm2

100A RCCB (type A = 90A) 35mm2 50mm2
250A switch disconnector 120mm2 (+ M8 lugs)
160A250A MCCB incomer 250A = 120mm2 (+ M8 lugs)
100A direct connection kit 35mm2
250A direct connection lugs 120mm2 (+ M8 lugs)
125A contactor incomer 50mm2
250A contactor incomer 120mm2 (+ M8 lugs)
Enclosure earth stud M6 M8
Incoming earth terminal 25mm2 125A = 25mm2, 250A = 70mm2
Incomming neutral terminal 90/100A = 35mm2, 125A = 50mm2 125A = 50mm2, 250A = 120mm2 (+ M8 lugs)
Outgoing earth terminal 25mm2 25mm2
Outgoing neutral terminal 25mm2 25mm2

2.4 MCB pan assemblies
Interiors & incoming devices for single phase and three phase Technical characteristics
Eaton MCB pan assemblies offer a high degree of flexibility for Eaton MCB pan assemblies are suitable for
custom applications. SPN types are available with 4, 7, 10, 13, and inclusion in other factory built assemblies and as
16 ways. TPN types are available with 4, 6, 8, 12,18 and 24 ways. replacements for distribution board interiors.
MCB pan assemblies feature fully shrouded busbars.
See pages 129 -130 for the technical details of Eaton MCB pan assemblies.
EAMP10 125A SPN type A pan assemblies with earth & neutral bars
4 way SPN, type A pan assembly 125 4 EAMP4

EAMS1251N Incoming devices for SPN, type A pan assemblies

Incoming devices supplied separate to pan assembly
Description Rating Poles Sensitivity Eaton list
(A) (mA) number
Switch-disconnector 125 SPSN EAMS1251N

RCCB 100 1P+N 30 EAMS100HE
RCCB 100 1P+N 100 EAMS100ME
RCCB 100 1P+N 300 EAMS100LE
Direct connection kit 100 1P+N EAMBT1002
EBMP61 125A/250A TPN type B pan assemblies with earth & neutral bars
4 way TPN, type B pan assembly 125 4 EBMP41

EBMS1253 125A incomer options for type B pan assemblies

Switch disconnector 125 TP EBMS1253

Switch disconnector kit (including single phasing link) 125 SPSN EBMS1251N
Switch disconnector 125 TPSN EBMS1253N
30mA RCCB 100 TPSN EBMR30
300mA RCCB with time delay 100 TPSN EBMR300T

MCB pan assemblies
2.4
EBMMB250 250A incomer options for type B pan assemblies
Switch-disconnector 250 TP EBMS2503

MCCB incomer kit (includes mCCB) 250 TP EBMMB250
MCCB incomer kit (includes mCCB) 160 TP EBMMB160
Single phase conversion kit for 250A rated board only (requires EBMS2503 to be ordered separately) EBMS25

Distribution board switch and protection devices
3
Eaton provides a comprehensive range of modular

solutions for circuit protection and control. Eatons
10/15kA MCBs are high performance current limiting
devices with the ability to disconnect overloads and
short circuits. They are available with trip types
B, C and D with many features of benefit to all
customers. RCBOs with overload protection combine
protection for people and circuits in a single module
width device where space is at a premium.
Double pole and four pole RCCBs are available
in a range of current ratings and four trip
sensitivities, 10, 30, 100 and 300mA.
3.1 MINIATURE CIRCUIT BREAKERS (MCBs) ............................................................................................................................... 46
3.2 RESIDUAL CURRENT CIRCUIT BREAKERS (RCCBs) .............................................................................................................. 48
3.3 RESIDUAL CURRENT CIRCUIT BREAKER WITH OVERCURRENT PROTECTION (RCBOs) .................................................. 49
3.4 ACCESSORIES .......................................................................................................................................................................... 51

3.1 Distribution board switch and protection devices
Miniature circuit breakers, MCBs , 18mm, 1A-63A
MCBs are available in current ratings from 1A63A, with trip types B, C and D, 10kA to IEC 60898 and 15kA to IEC 60947-2
EMDH104 Miniature circuit breakers dual rated 10/15kA, single pole


1)
EMBH125N Miniature circuit breakers dual rated 10/15kA, single pole + neutral
Miniature circuit breaker 1 36 10/15 EMBH101N EMCH101N EMDH101N

Miniature circuit breaker 50 36 10/15 EMBH150N EMCH150N EMDH150N1)
Miniature circuit breaker 63 36 10/15 EMBH163N EMCH163N EMDH163N1)
1)
EMCH220 Miniature circuit breakers dual rated 10/15kA, double pole

Description Rated Width (mm) Short circuit Eaton list number
current (A) rating (kA) Trip type B Trip type C Trip type D

1)
Miniature circuit breakers, MCBs 3.1
EMCH363 Miniature circuit breakers dual rated 10/15kA, three pole
1)
EMCH410 Miniature circuit breakers dual rated 10/15kA, four pole

1)
Miniature circuit breakers, MCBs, 27mm, 20A-125A

MCBs are available in current ratings from 20A125A, with trip types B, C and D, 15kA to 25kA to IEC 60947-2
Miniature circuit breakers - single pole
Miniature circuit breaker 20 27 25kA EMBS120 EMCS120 EMDS120
Miniature circuit breaker 125 27 15kA EMBS1125 EMCS1125
Miniature circuit breakers - three pole

Miniature circuit breaker 125 81 15kA EMBS3125 EMCS3125

Residual current circuit breakers
EAM162H RCCBs 2-pole double module 10mA30mA sensitivity

Description Poles Rating Sensitivity Eaton list
(A) (mA) number
16A 2-pole RCCB 10mA 2P 16 10 EAM162V

16A 2-pole RCCB 30mA 2P 16 30 EAM162H
EAM402M RCCBs 2-pole double module 100mA sensitivity

(A) (mA) number
25A 2-pole RCCB 100mA 2P 25 100 EAM252M

EAM802L RCCBs 2-pole double module 300mA sensitivity

(A) (mA) number
25A 2-pole RCCB 300mA 2P 25 300 EAM252L

EAM404H RCCBs 4-pole 30mA sensitivity

(A) (mA) number

EAM404M RCCBs 4-pole 100mA sensitivity

(A) (mA) number

EAM404L RCCBs 4-pole 300mA sensitivity

(A) (mA) number

100A 4-pole RCCB 300mA 4P 100 300, trip time delay EAM1004LT

Residual current circuit breaker with overcurrent protection (RCBOs) 3.3
EMBH106R10C RCBOs single pole trip type B 10mA sensitivity

(A) (mA) number


(A) (mA) number


(A) (mA) number

EMCH120R10C RCBOs single pole trip type C 10mA sensitivity

(A) (mA) number


(A) (mA) number


(A) (mA) number


Residual current circuit breaker with overcurrent protection (RCBOs)
169608 RCBOs 3P+N 10kA

Conditionally surge current-proof 250A.
Sensitivity type A, providing protection against AC and pulsating DC earth fault currents.
Trip types B, C, and D
Trip sensitivity 30mA, 100mA or 300mA
Characteristic B (A) (mA) number

Characteristic C (A) (mA) number
3P+N RCBO20A 10kA trip C 20 30 mRBM4-20/3/C/003-A-UK-PT 169644

Characteristic D (A) (mA) number
Accessories MCBs, RCCBs & RCBOs 3.4
ASPDL Padlocking devices
For MCBs, RCCBs, RCBOs & switch disconnectors
The wide range of Eaton devices are complimented by a range of padlocking devices.
For MCBs and RCCBs the device mechanism is trip free which allows it to be padlocked ON for security, but in
the event of a fault condition the device will still operate to disconnect the fault. The device will move to the tripped
position when the lock is removed. These devices can also be padlocked in the OFF position.
number
Universal device lockout attachment fits MCBs, RCCBs and RCBOs ASPDL
Lockout attachment for 27mm MCBs ASPDL27
Padlock PD2
ASALMSN Auxiliary and alarm contacts including test function

For 18mm MCB & RCBO
Auxiliary and alarm contact devices can be fitted together on one MCB. Each is incorporated in a 1/2
module (9 mm) casing with terminals protected to IP 20 capable of accepting cable up to 2.5 mm2.
These devices are designed and manufactured to IEC 60947-5-1 and incorporate a changeover switch
providing remote indication of an MCB which has tripped under fault conditions.
This auxiliary switch allows remote indication of the position of the MCB contacts.
Auxiliary and Alarm contact ratings:
AC14 240 Vac 50Hz, 6A.
DC14 125 Vdc, 1A.
The auxiliary contact will not differentiate between an MCB that is off or tripped.
The auxiliary contact can be used in conjunction with a remote supply and signal lamps, bells or buzzers.
Description Quantity Eaton list
per carton number
Auxiliary switch incorporating a test function 1 ASAUXSN1)

Alarm switch incorporating reset and test function 1 ASALMSN1)
1)
Not suitable for use in distribution boards
ASSNTSN415 Shunt trips

For 18mm MCB & RCBO
Suitable for all Eaton MCBs including those with either auxiliary or alarm contacts.
A shunt trip and undervoltage release can be fitted together on one MCB.
Each is incorporated in a 1 module (18 mm) casing with terminals protected to IP 20 capable of accepting
cable up to 2.5 mm2.
The shunt trip and UVR are simply clipped to the left hand side of an MCB and have terminals at one end to allow
connection to pan assemblies and comb busbar.
A shunt release provides remote trippping of an MCB with three voltage options for AC & DC applications.
Description dc characteristics ac characteristics Quantity Eaton list
per carton number
MCB shunt trip 48 V60 Vdc 48 V110 Vac 1 ASSNTSN1101)

MCB shunt trip 110 Vdc 240 Vac 1 ASSNTSN4151)
1)
Other voltages are available.
ASUVRSC230 Under voltage release

For 18mm MCB & RCBO
Under voltage release (UVR) for remote tripping of an emergency stop loop.
The UVR is simply clipped to the left hand side of an MCB and have terminals at one end to allow
connection to pan assemblies and comb busbar.
Description ac characteristics Quantity Eaton list
per carton number
Under voltage release 240 Vac 1 ASUVRSC2301)

1)

4
Eatons wide range of modular timers and twilight

switches are suitable for any residential or commercial
application offering automatic lighting control. Contactors
are frequently applied for switching of lamp loads, fans
or pumps in both utility as well as industrial areas.
4.1 MODULAR SWITCHES / TIMERS AND TWILIGHT SWITCHES
Universal declaration type coding................................................................................................................................................. 54
Analogue time switches - 50 Hz mains synchronised................................................................................................................. 55
Analogue time switches - Quartz controlled ............................................................................................................................... 55
Analogue weekly time switches - Quartz controlled .................................................................................................................. 55
Digital weekly time switches, 1 channel ..................................................................................................................................... 56
Digital weekly time switches, 2 channel ..................................................................................................................................... 57
Twilight switches for DIN rail mounting ...................................................................................................................................... 58
Twilight switch for surface mounting .......................................................................................................................................... 59
Antenna for DCF signal reception ............................................................................................................................................... 60
Antenna including power supply for GPS signal reception ......................................................................................................... 60
Programming software kit including memory card ..................................................................................................................... 60
4.2 CONTACTORS
Contactors, 20A .......................................................................................................................................................................... 61
Contactors, 25A .......................................................................................................................................................................... 61
Contactors, 40A .......................................................................................................................................................................... 61
Contactors, 63A .......................................................................................................................................................................... 62
Day/night contactors ................................................................................................................................................................... 62
Auxiliary contacts ....................................................................................................................................................................... 62

4.3 TRANSFORMERS AND EARTH LEAKAGE RELAYS
Transformer 8/12v 1.0A ............................................................................................................................................................... 63
Earth leakage relays and current transformers ........................................................................................................................... 63

4.1 Modular control and switching devices
Timers and twilight switches
1 Switches and twilight switches Technical characteristics (depending on type)

Timers & Twilight Switches are applied in any residential,
commercial and industrial buildings wherever automatic control Modular design.
is required on predefined times and/or depending on daylight Analogue and digital timers.
intensity. Time adjustment by 50 Hz net, quartz control, DCF1)
Timers & Twilight Switches are applied in any residential, or GPS signal
Technical reception 2).
characteristics (depending on type)
The Eaton range
commercial and comprises of a widewherever
industrial buildings variety ofautomatic
different control
Modular
O Manual override
design. switching function.
is required on predefined times and/or depending on daylight
products which include analogue Timers, digital Timers, Twilight
intensity. Analogue and digital
Power reserve
O
for alltimers.
quartz and DCF or GPS driven switches.
Switches and Staircase Timers.
Time adjustment by 50
forHz net, quartz control, DCF 1)
Remote light sensor twilight switching.
O
The Eaton range comprises of a wide variety of different or GPS signal reception .
2)
products which include analogue Timers, digital Timers, Twilight

These Timers Manual override switching function.
andcan either be controlled by a 50Hz
O
Switches Staircase Timers. Benefits

O
Power reserve for all quartz and DCF or GPS driven
net-synchronisation, quartz control and time synchronisation switches.
These Timers can either be controlled by a 50 Hz net-
synchronisation,
or using the DCF quartz control
signal or and time synchronisation
GPS antenna,which guaranteesor using
100% Remote light
Computer
O
sensor
aided for twilightsoftware
programming switching.
available.
the DCF signal or GPS antenna, which guarantees 100% accuracy
accuracy at all
at all times. times.for
Except Except for net-synchronised
net-synchronised timers alltimers all units
units do have Compact 18 mm design for restricted space opportunities.
self power reserve to secure the time setting and program Benefits
do have self power reserve to secure the time setting and program Separate IP40 covers are available for direct wall mounting.
storage in case a power interruption does occur. O
storage in case a power interruption does occur. Computer
High level aided
of accuracy.
O
programming software available.
Dedicated computer software and memory cards are available to
support the programming of our most advanced timers. Compact
Automatic
O
18summer and winter
mm design time adjustment.
for restricted space opportunities.
Dedicated
Automaticcomputer software
summer and winterand memory
time, holidaycards are available to
and random Separate
O Holiday &IP40
Random program
covers settings.
are available for direct wall mounting.
switching
support theprograms complete
programming of ourthe functionality
most advancedof our range.
timers.
High
Highlevel
O
powerof reserve
accuracy.
up to 10 years.
Automatic summerare
Twilight Switches andsupplied
winter time, holiday
with a remoteand random
light sensor, which O
can be easily installed on the outside wall where the required Notes:
switching programs complete the functionality of our range.
light intensity threshold can be simply adjusted on the modular
Holiday & Random program settings.
O
device itself. 1)
O
Automatic
High powercalculation
reserve upoftosunrise and sunset times throughout
10 years.
Twilight Switches are supplied with a remote light sensor, which the year, including the possibility of astro times + / -2 hour shift.
Notes:
can be easily installed on the outside wall where the required 1)
2) Automatic
The calculation
DCF-signal of sunrise
can only and sunset
be received within times throughout
a 1000 km radius.
the year, including the possibility of astro times + / -2 hour shift.
light intensity threshold can be simply adjusted on the modular
device itself. 2)
The DCF-signal can only be received within a 1000 km radius.
Universal declaration
Universal declaration type
type coding
coding
Type coding - analogue switches Type coding - digital switches

TS Q D 1NO TS D W 1CO -
TS S D 1NO TS D W 2CO -
TS Q D 1CO TS D W 1CO A
TS S D 1CO TS D W 1CO DG
TS Q W 1CO TS D W 1CO MIN
TS = Switch TS = Switch
Q/S = Quartz / 50 Hz net-synchronisation D = Digital
D/W = Day / week programme W = Week programme
1NO / 1CO = Create / change (contact configuration) 1CO / 2CO = Exchange / 2 x changeover (contact configuration)
A = Astroclock
DG = DCF or GPS controlled
MIN = Compact 18mm design version
Type coding - digital switches and accessories Type coding - twilight switches
TS A DCF SR S D 1NO -
TS A GPSKIT SR S W 1NO -
TS A MEMKIT SR C D 1CO -
TS A MEM SR S D 1CO W
TS =
Switch SR = Twilight switch
A =
Accessory S/C = With or without sensor
DCF =
DCF-antenna D/W = DIN rail mounting / surface mounting
GPSKIT =
Antenna for GPS signal reception including 1NO / 1CO = Create / change (contact configuration)
power supply W = Wide adjustable sensitivity (2 - 50000 lux)
MEMKIT = Programming software kit
MEM = iMemory
4 SWITCHCLOCK AND LIGHT SWITCHES CA081003EN - January 2013

Analogue timers 4.1
Technical characteristics (dependant of type)
Supply voltage 230 V / 50 - 60 Hz (50 Hz for just synchronised versions)
50 Hz-mains synchronised or Quartz controlled.
Daily or weekly programme.
Manual override switching function.
Compact 18mm design for restricted space opportunities.
See page 60 for accessories

167391 Analogue time switches - 50 Hz mains synchronised

Standard version
Program Contact Power Min. cycling Eaton list
range Type Channels configuration reserve time Width Type QPC number
Day 50 Hz-net 1 CO - 15 min. 52.5 mm TSSD1CO 1 167391
167389 Analogue time switches - 50 Hz mains synchronised

18 mm compact design
Day 50 Hz-net 1 NO - 15 min. 17.5mm TSSD1NO 1 167389
167390 Analogue time switches - Quartz controlled

Standard version
Day Quartz 1 CO 200 hrs 15 min. 52.5 mm TSQD1CO 1 167390
167388 Analogue time switches - Quartz controlled

Day Quartz 1 NO 3 y rs 15 min. 17.5 mm TSQD1NO 1 167388
167392 Analogue weekly timer switches - Quartz controlled

Standard version
Week Quartz 1 CO 200 hrs 2 hrs 52.5 mm TSQW1CO 1 167392

Digital timers
Technical characteristics Display back light (switchable).

Operating voltage 230 V / 50 - 60 Hz. Compact 18mm design for restricted space.
1 or 2 channel. Automatic summer and winter adjustment.
Quartz controlled. Holiday programme.
3 to 10 year power reserve. Zero crossing switching relay for longer life.
Weekly programme. Integrated operating hour counter.
Manual ON (and depending on type OFF) switching. TSDW1CO, TSDW2CO, TSDW1COA, TSDW1CODG:
Text-oriented user guidance in display. Interface for memory.

167379 Digital weekly time switches, 1 channel

Standard version
Week Quartz 1 CO 10 year 1 min. 56 35.8 mm TSDW1CO 1 167379

1TE wide version
Week Quartz 1 CO 3 year 1 min. 28 17.5 mm TSDW1COMIN 1 167383

Version with Antenna connection
Quartz,
Week DCF / GPS 1 CO 10 year 1 sec. 84 35.8 mm TSDW1CODG 1 167382

Astronomical
Quartz with
Week astronomical 1 CO 10 year 1 min. 56 35.8 mm TSDW1COA 1 167381

Digital timers 4.1
167380 Digital weekly time switches, 2 channels
Standard version
Week Quartz 2 2 x CO 10 year 1 min. 56 35.8 mm T SDW2CO 1 167380

Twilight switches for DIN rail mounting
Operating voltage 220 - 240 V / 50 - 60 Hz.
1 channel.
Controlled by external light sensor (supplied).
Built-in time delay included for unwanted switching e.g. due to car lamp influences (adjustable to
type SRSD1COW and SRCD1CO).Manual ON (and depending on type OFF) switching.
Text-oriented user guidance in display.
Switching status indication.
Adjustable light intensity level.
SRCD1CO
Manual ON and OFF switching.
Back lit display.
Holiday programme.
Zero crossing switching relay for longer life.
Integrated operating hour counter.
Memory interface.
Test function.

See page 143 for the technical data
167375 Twilight switches for DIN rail mounting

Adjustable Contact Eaton list
Description Channels sensitivity configuration Width Type QPC number
Twilight switch with light sensor 1 2 - 100 lux NO 17.5 mm SRSD1NO 1 167375

Advanced version, 1 channel
Description Channels sensitivity configuration Width Type QPC number
Twilight switch with light sensor 1 2 - 200 lux CO 54 mm SRSD1COW 1 167378

Combined version
Program range Channels sensitivity configuration Width Type QPC number
Week 1 2 - 200 lux CO 72 mm SRCD1CO 1 167377

Twilight switch for surface mounting 4.1
Operating voltage 220 - 230 V / 50 - 60 Hz.
1 channel.
Integrated light sensor.
Time delay included for unwanted switching,
adjustable (e.g. due to car lamp influences).
Back or bottom cable entry.
Adjustable light intensity on the outside.
Large light level (180 degrees).
Test button.
Degree of protection: IP55.

167376 Twilight switch for surface mounting

1 channel
Program range Channels sensitivity configuration Width Type QPC number
Week 1 2 - 2.000 lux NO 85 mm SRSW1NO 1 167376

Accessories
167384 Antenna for DCF signal reception

By using DCF reception 100% accuracy is obtained. A DCF antenna is required to be
mounted on an outside wall. The DCF signal reception is only operable when the timer
is connected to the remote DCF antenna and fed by a DCF power supply.
DCF antenna for digital TSDW1CODG.
Eaton list
Description Type QPC number
DCF-antenna 1 TSADCF 1 167384
167385 Antenna includes power supply for GPS signal reception

Antenna includes power supply for TSDW1CODG.
Eaton list
Antenna for GPS signal reception, includes power supply TSAGPSKIT 1 167385
167387 Programming software kit

For SRCD1CO, TSDW1CO, TSDW2CO, TSDW1COA, TSDW1CODG.
Eaton list
Programming software kit including adaptor cable, software and memory card TSAMEMKIT 1 167386
Memory card TSAMEM 1 167387
See pages 139-144 for timers and twilight switches technical data and overall dimensions.

Contactors 4.2
For other coil voltages contact technical support See pages 145-146 for contactors technical data and overall dimensions.
CR2011230A Contactors, 20 A ac coil

When several contactors are mounted it is advisable to fit a blanking module, List number EMBP, every two contactors.
Description Rating Coil voltage Coil voltage Width Contacts Eaton list
(A) (Vac) (Vdc) (mm) number
Contactor 20 230 18 1 NO + 1 NC CR2011230A

Contactor 20 230 18 2 NC CR2002230A
Contactor 20 230 18 2 NO CR2020230A
CR2020024 Contactors, 20 A ac/dc coil

Contactor 20 230 220 18 1 NO + 1 NC CR2011230

Contactor 20 230 220 18 2 NC CR2002230
Contactor 20 230 220 18 2 NO CR2020230
CR2540230A Contactors, 25 A ac coil

Contactor 25 230 36 2 NO + 2 NC CR2522230A

Contactor 25 230 36 4 NC CR2504230A

Contactor 25 230 220 36 2 NO + 2 NC CR2522230

Contactor 25 230 220 36 3 NO CR2530230
Contactor 25 230 220 36 4 NC CR2504230
Contactor 25 230 220 36 4 NO CR2540230

Contactor 40 230 220 54 2 NC CR4002230

Contactor 40 230 220 54 2 NO CR4020230
Contactor 40 230 220 54 3 NO CR4030230
Contactor 40 230 220 54 4 NO CR4040230

Contactors

Contactor 63 230 220 54 2 NO CR6320230

Contactor 63 230 220 54 4 NO CR6340230
CRM2540230A Day/night contactors, 2025 A ac coil

When several contactors are mounted it is advisable to fit a blanking module or spacer every two contactors.
Day/night contactors do have a manual override function, which enables the user to bring the contactor in either
a forced ON or OFF position. The contactor can only be brought into the forced ON position when it is
de-energised. When the contactor is energised the operation will return into the normal/automatic position.
Description Rating Coil voltage Width Contacts Eaton list
(A) (Vac) (mm) number
Contactor 20 230 18 2 NO CRM2020230A

Contactor 25 230 36 4 NO CRM2540230A
CRA611 Auxiliary contacts

Can be connected at the right-side of the contactor.
Description Rating Width Contacts
Eaton list
(A) (mm) number
Auxiliary 6 9 1 NO + 1 NC CRA611
Auxiliary 6 9 2 NO CRA620

Transformers and earth leakage relays 4.3
TR-G3/8 Transformers
Eaton list
Description Volts Amps Width (mm) Module number
Bell Transformer 2 module 12 0.6 36 1 TR-G3/8

8 1.0
Earth leakage relays & CTs

Suitable for use with all Eaton MCCBs & MCBs to provide 50/60Hz. Output contacts (volt-free) rated at 250V ac, 6A.
add-on earth leakage protection functionality. The earth Power and system LEDs show status of the relay, CT continuity,
leakage relay is used with an ELRCT series current transformer level of earth leakage, earth leakage trip. Eaton earth leakage
(core balance) and an appropriate MCB/MCCB shunt trip or relays are designed & tested in accordance with IEC61008-1.
undervoltage release. Power supply required 220-240V ac, See page 147 for dimensional details.
PFR-5 Earth leakage relays adjustable trip

Description Sensitivity Time delay Width Eaton list
number
Earth leakage relay Adjustable 30mA,100mA, 300mA, 500mA, 1A, 3A, 5A Adjustable 0.02, 0.1, 0.3, 0.5, 1, 3, 5s 36mm PFR-5
PFR-003 Earth leakage relays fixed trip

Description Sensitivity Time delay Width Eaton list
number
Earth leakage relay Fixed 30mA Instantaneous (0.02s) 36mm PFR-003

Earth leakage relay Fixed 300mA Instantaneous (0.02s) 36mm PFR-03
PFR-W-20 Current transformers (core balance)

PFR-W-105
One current transformer required per relay.
Description Inner Eaton list
dimension number
Current Transformer 20mm diameter PFR-W-20

30mm diameter PFR-W-30

Memshield 3 MCCB panelboards and associated devices
5
A complete range of MCCB panelboards and pan

assemblies providing all the options you need from
a straightforward panelboard to a comprehensive
panelboard system. The range now offers a variety of
incoming devices and a greater choice of outgoing ways
to provide more flexibility and choice to the user.
5.1 INCOMING DEVICE RATINGS UP TO 250A OUTGOING DEVICE RATINGS UP TO 160A ................................................. 66
5.3 INCOMING DEVICE RATINGS UP TO 400A OUTGOING DEVICE RATINGS UP TO 250A .................................................. 74
5.6 PLUG-IN INCOMING METERING ............................................................................................................................................. 86
5.7 PLUG-IN OUTGOING METERING ............................................................................................................................................ 88
5.8 LIGHTNING & SURGE SUPPRESSION FOR MCCB PANELBOARDS .................................................................................... 90
5.9 MCCB PAN ASSEMBLIES ......................................................................................................................................................... 91

5.1 Memshield 3 MCCB panelboards and associated devices
Incoming device ratings up to 250A outgoing device ratings up to 160A
Specification Features
Panelboards to IEC61439-2. Form 3b Type 2 4, 6, 8, or 12 outgoing TP ways
Busbar system KEMA certified 50kA Icc, Icw 25kA 1s Outgoing devices; NZM1 16A125A SP & 20A160A TP
IP3X construction Tinplated busbars
MCCBs to IEC60947-2. kA ratings shown are Ics=Icu at 400V ac Can be configured for incomer device at top of panelboard
Switch disconnectors to IEC60947-3 Removable side gland plates as standard
Wide range of extension boxes, metering, surge
protection, and earth leakage incomer options available
See pages 149-151 for dimensions.
EPBN1425 Minimum ordering requirement: panelboard + incoming device + incomer

connection kit + outgoing devices + blanking plates
Description Associated Current rating No. of ways Eaton list
incoming device (A) number
Incoming rating up to 250A, NZM2 MCCB or N2 switch disconnector 250 4 EPBN1425

outgoing ratings up to 160A or direct lugs connection 6 EPBN1625

8 EPBN1825
EPBN11225
12
NZMC2-A250KCO MCCB incoming device

36kA or 50kA options
Select appropriate incomer device from table below
Maximum cable capacity 185mm2
Adjustable trip. Thermal trip adjustment 0.8 to 1 x In, Magnetic trip adjustment 6 to 10 x In
Poles Incoming device Current rating Eaton list number
type (A) Short circuit rating
36kA 50kA
3-pole NZM2 MCCB 160 NZMC2-A160KCO NZMN2-A160KCO

200 NZMC2-A200KCO NZMN2-A200KCO
250 NZMC2-A250KCO NZMN2-A250KCO
4-pole (3 phase and switched neutral) NZM2 MCCB 160 NZMC2-4-A160KCO NZMN2-4-A160KCO
200 NZMC2-4-A200KCO NZMN2-4-A200KCO
250 NZMC2-4-A250KCO NZMN2-4-A250KCO
N2-250KCO Switch disconnector (non-automatic) incoming device

Poles Incoming device Current rating Eaton list
type (A) number
3-pole N2 Switch disconnector 250 N2-250KCO

4-pole N2 Switch disconnector 250 N2-4-250KCO

Incoming device ratings up to 250A outgoing device ratings up to 160A 5.1
EPBKN125L Incomer connection kit/metering connection kit
See incoming metering section below to order metering components
Poles Maximum rating Eaton list
(A) number
3-pole incomer connection kit 250 EPBKN1253

3-pole incomer connection kit includes metering CT and CT to meter cable 250 EPBKN1253M
Direct connection lugs kit 250 EPBKN125L
Direct connection lugs kit includes metering CT and CT to meter cable 250 EPBKN125LM
Adapter kit for use when incomer device mounted at top of panelboard 230 EPBKTFSN21)
1)
Maximum rating of panelboard when top fed is 230A
NZMB1-1-AF63 Outgoing devices NZM1 frame MCCBs

and NZMB1-A160
Single pole fixed trip. Triple pole thermal trip adjustment 0.8 to 1 x In, magnetic trip adjustment 6 to 10 x In
Rating Eaton list number
(A) Single pole 25kA Triple pole 25kA1) 2)
16 NZMB1-1-AF16
20 NZMB1-1-AF20 NZMB1-A20
100 NZMB1-1-AF100 NZMB1-A100
125 NZMB1-1-AF125 NZMB1-A125
160 NZMB1-A160
1)
36kA triple pole also available, change B to C in list number, ie NZMC1-A125
2)
50kA triple pole also available, change B to N in list number, ie NZMN1-A125
EPBN1BP1 Accessories
number
SP blanking module NZM1 frame (i.e. order 3 per TP way) EPBN1BP1

Panel door lock with 2 keys (have same key code) EPBDLK1
Terminal shroud for outgoing MCCB type NZM1 1P NZM1-1-XKSA
Terminal shroud for outgoing MCCB type NZM1 3P NZM1-XKSA
Shunt trip 208-250AC/DC for NZM1 (excl. 1P) 259744
Shunt trip 208-250AC/DC for NZM2/N2 259763
Undervoltage release 208240AC for NZM1 (excl. 1P) 259471
Undervoltage release 208240AC for NZM2/N2 259499
Handle lock for MCCB type NZM1 260199
Handle lock for MCCB types NZM2 and NZM3 260201
EPBN1425SXB Cable extension boxes side mounted

number
To fit 4 way panelboard EPBN1425 EPBN1425SXB


EPBN1EX250 Cable extension boxes top/bottom mounted

number
250mm high EPBN1EX250
EPBN1CX250 Corner filler boxes

number
For use where top/bottom/meter boxes are fitted in conjunction with side cable boxes EPBN1CX250
EPBN1EXDIN Din rail extension boxes

Description Height Number 18mm Eaton list
Din modules number
For housing din rail mounted command/control equipment, ie timers/contactors 250mm 15 EPBN1EXDIN
Metering components refer to pages 86-89 for more explanation

(Requires appropriate incomer connection kit with metering option selected from above)
EPBMETER1 Incoming metering digital

Includes both Modbus and Pulsed outputs
number
Incomer meter enclosure (can be fitted to top or bottom of panelboard). Meter not included EPBN1EX250M
Multifunction meter measuring parameters:
Voltage (P-P / P/N) (individual/average)
Current (I1, I2, I3) (individua/average)
Frequency
Power factor (individual/average)
Active, reactive, apparent power (individual/total)
Active, reactive, apparent energy (total) EPBMETER1
Voltage supply to meter tap off kit (includes protection fuses). One per panelboard required, irrespective of number of meters EPBN1SUPM

EPBN11225SXM Outgoing side mounted metering digital
Description Number of meter Number of meter Eaton list
spaces in metering blanking plates number
enclosure included
Side mounted metering enclosure to fit 4 way panelboard EPBN1425 2 1 EPBN1425SXM1)

Outgoing CT Kit (1 off required per metered outgoing TP way) to suit NZM1 frame MCCBs.
160A maximum rating. Includes CT to meter plug-in cable and meter to meter voltage supply linking cable with connectors EPBCTMT160
Three phase splitter box to allow separate monitoring of a three phase current transformer on individual energy meters EPBCTMT3P
Meter includes both Modbus and Pulsed outputs
Current (I1, I2, I3) (individua/average)
Frequency
Voltage supply to meter tap off kit (includes protection fuses), not required if incoming metering is being used EPBN1SUPM
Extra long (2m) meter to meter voltage supply linking cable with connectors EPBN3LKKTM
Extra long (2.5m) CT to meter plug-in cable EPBN3LKRJ45
CT supporting mount to allow CT to be fitted in side mounted cable extension box if terminal shields being fitted to MCCBs EPBSXBCTMT
Spare blanking plate for unused meter ways in metering enclosure EM96BP
1)
S uffix M indicates cut-outs for meters and hinged door for outgoing metering suitable for left and right
hand applications. Can be used with side mounted cable extension boxes if required
EPBN1SPD123 Transient voltage surge suppression units, externally mounted in own enclosure
See page 90 for full technical specification
Includes 63A TP NZM1 MCCB for protection/isolation
See page 131 for dimensions
number
SPD-type T1, T2, T3 in accordance with EN 61643-11, lightning protection classes III and IV in accordance with IEC 62305 EPBN1SPD123
SPD-type T1, T2, T3 in accordance with EN 61643-11, lightning protection classes I, II, III and IV in accordance with IEC 62305 EPBN1SPD1234
EPBKEL250 Earth leakage protection

Direct bolt-on module used in conjunction with 4-pole incomer device, 250A maximum rating
Sensitivity adjustable from 0.1A to 3A. Time delay adjustable from 60ms to 450ms
number
Earth leakage protection add-on kit for incomer device. 250mm high extension box included EPBKEL250
Cable size summary

Incoming cables
MCCB or switch disconnector size max/type 185mm2/tunnel terminals
Direct connection lugs incomer M8
Neutral M8
Earth M10
Outgoing cables
NZM1 MCCB size max/type 70mm2/cable clamp (95mm2 can be fitted depending on cable manufacturer)
Neutral size max/type 50mm2 tunnel terminals and 2 x M8 bolts
Earth size max/type 50mm2 tunnel terminals

Panelboards to IEC61439-2. Form 3b Type 2 6 or 12 outgoing TP ways
Busbar system KEMA certified 50kA Icc, Icw 30kA 1s Outgoing devices; NZM1 16A125A SP & 20A160A TP
IP3X construction Tinplated busbars
MCCBs to IEC60947-2. kA ratings shown are Ics=Icu at 400V ac Can be configured for incomer device at top of panelboard
Switch disconnectors to IEC60947-3 Removable side gland plates as standard
See pages 149 -151 for dimensions.

Description Associated Current rating No. of ways Eaton list
incoming device (A) number
Incoming rating up to 400A, NZM3 MCCB or N3 switch disconnector 400 6 EPBN1640

outgoing ratings up to 160A or direct lugs connection 12 EPBN11240
NZMN3-A400 MCCB incoming device

50kA
type (A) Short circuit rating
3-pole NZM3 MCCB 250 NZMN3-A250

320 NZMN3-A320
400 NZMN3-A400
4-pole (3 phase and switched neutral) NZM3 MCCB 250 NZMN3-4-A250
320 NZMN3-4-A320
400 NZMN3-4-A400
N3-400 Switch disconnector (non-automatic) incoming device

type (A) number
3-pole N2 switch disconnector 400 N3-400

4-pole N2 switch disconnector 400 N3-4-400

EPBKN2403 Incomer connection kit/metering connection kit
(A) number

4-pole incomer connection kit 400 EPBKN24041)
1)
Requires use of cable extension box EPBN2EX250
2)

and NZMB1-A160
(A) Single pole 25kA Triple pole 25kA1) 2)
16 NZMB1-1-AF16
100 NZMB1-1-AF100 NZMB1-A100
125 NZMB1-1-AF125 NZMB1-A125
160 NZMB1-A160
1)
36kA triple pole also available, change B to C in list number, ie NZMC1-A125
2)
50kA triple pole also available, change B to N in list number, ie NZMN1-A125
EPBDLK1 Accessories
number

Shunt trip 208250AC/DC for NZM1 (excl. 1P) 259744
Shunt trip 208250AC/DC for NZM3/N3 259763

number



number

number

Din modules number

EPBN2EX250M Incoming metering digital

See page 86 for detailed selection guide
number
Current (I1, I2, I3) (individual/average)
Frequency

enclosure included

Outgoing CT Kit (1 off required per metered outgoing TP way) to suit NZM1 frame MCCBs. 160A maximum rating.
Includes CT to meter plug-in cable and meter to meter voltage supply linking cable with connectors EPBCTMT160
Frequency
1)
number

Kit comprises 350mm high extension box fitted with earth leakage relay, core balance
transformer, all cables/terminals/protection fuses, and 230V shunt trip (for tripping of
incomer device). Requires 4-pole incomer device. 400A maximum rating
Sensitivity adjustable from 30mA to 5A. Time delay adjustable from 0.02 to 5 seconds
number
Earth leakage protection add-on module for incomer device EPBKEL400
Cable size summary

Incoming cables
MCCB or switch disconnector size max/type 240mm2/M12 bolt
Neutral M8
Earth M10
Outgoing cables
NZM1 MCCB size max/type 70mm2/cable clamp. (95mm2 can be fitted depending on cable manufacturer)
Earth size max/type 50mm2 tunnel terminals

Panelboards to IEC61439-2. Form 3b Type 2 6, 12 or 18 outgoing TP ways
Busbar system KEMA certified 50kA Icc, Icw 35kA 1s Outgoing devices; these panelboards utilise two
IP3X construction frame sizes of MCCB: NZM2 125A250A TP, and
NZM1 SP 16A125A or TP 20A160A
MCCBs to IEC60947-2. kA ratings shown are Ics=Icu at 400V ac
Tinplated busbars
Switch disconnectors to IEC60947-3
Can be configured for incomer device at top of panelboard
Removable side gland plates as standard
See pages 149 -151 for dimensions.

Description Associated Current No. of outgoing ways Eaton list
incoming device rating (A) number
Incoming rating up to 400A, NZM3 MCCB or N3 Switch Disconnector 400 6 (2 x 250A + 4 x 160A) EPBN2640
outgoing ratings up to 250A or direct lugs connection 12 (2 x 250A + 10 x 160A) EPBN21240
18 (2 x 250A + 16 x 160A) EPBN21840
NZMN3-A400 MCCB incoming device

50kA
type (A) number
3-pole NZM3 MCCB 250 NZMN3-A250

320 NZMN3-A320
400 NZMN3-A400
4-pole (3 phase and switched neutral) NZM3 MCCB 250 NZMN3-4-A250
320 NZMN3-4-A320
400 NZMN3-4-A400
N3-400 Switch disconnector (non-automatic) incoming device

type (A) number
3-pole N2 switch disconnector 400 N3-400

4-pole N2 switch disconnector 400 N3-4-400

(A) number

4-pole incomer connection kit 400 EPBKN24041)
1)
Requires use of cable extension box EPBN2EX250
2)
NZMC2-A250-BT Outgoing devices NZM2 frame MCCBs

Up to 2 can be fitted
Adjustable trip. Thermal trip adjustment 0.8 to 1 x In, magnetic trip adjustment 6 to 10 x In
(A) Triple pole 36kA Triple pole 50kA
125 NZMC2-A125-BT NZMN2-A125-BT


and NZMB1-A160
(A) Single pole 25kA Triple pole 25kA Triple pole 36kA1)
16 NZMB1-1-AF16
20 NZMB1-1-AF20 NZMB1-A20 NZMC1-A20
160 NZMB1-A160 NZMC1-A160
1)
50kA triple pole also available, change C to N in list number, ie NZMN1-A125
tunnel terminals Description Eaton list
number

TP blanking module NZM2 frame EPBN2BP3

number


number

number

Din modules number


number
Frequency

enclosure included

Side mounted metering enclosure to fit 18 way panelboard EPBN21840 9 8 EPBN21840SXM
Frequency
1)
number

number
Earth leakage protection add-on kit for incomer device EPBKEL400
Cable size summary

Incoming cables
MCCB or switch disconnector size max/type 240mm2/M12 bolt
Neutral M8
Earth M10
Outgoing cables
NZM2 MCCB size max/type 185mm2/cable clamp
NZM1 MCCB size max/type 70mm2/cable clamp. (95mm2 can be fitted depending on cable manufacturer)
Earth size max/type 50mm2 tunnel terminals and 4 x M8 bolts

Panelboards to IEC61439-2. Form 3b Type 2 6, 12 or 18 outgoing TP ways
Busbar system KEMA certified 50kA Icc, Icw 50kA 1s Outgoing devices; these panelboards utilise two
IP3X construction frame sizes of MCCB: NZM2 125A250A TP, and
NZM1 SP 16A125A or TP 20A160A
MCCBs to IEC60947-2. kA ratings shown are Ics=Icu at 400V ac
Tinplated busbars
Switch disconnectors to IEC60947-3
Can be configured for incomer device at top of panelboard
Removable side gland plates as standard
Door lock included

Incoming rating 630A, NZMLW MCCB or NLW CBS 630 8 (4 x 250A + 4 x 160A) EPBN2863
outgoing ratings up to 250A or direct lugs connection 12 (4 x 250A + 8 x 160A) EPBN21263
18 (4 x 250A + 14 x 160A) EPBN21863
NZMLW-630 MCCB incoming device

50kA
Maximum cable capacity 2 x 300mm2
Thermal trip fixed at 630A, Magnetic trip adjustment 2 to 8 x In
type (A) number
3-pole NZMLW MCCB 630 NZMLW-A630

4-pole (3 phase and switched neutral) NZMLW MCCB 630 NZMLW-4-A630
NLW-630 Circuit breaker switch incoming device

50kA
type (A) number
3-pole NLW Circuit breaker switch 630 NLW-630

4-pole NLW Circuit breaker switch 630 NLW-4-630

(A) number
3-Pole incomer connection kit 630 EPBKN2633

3-Pole incomer connection kit includes metering CT and CT to meter cable 630 EPBKN2633M
Adapter kit for use when incomer device mounted at top of panelboard 570 EPBKTFSLW1)
1)



and NZMB1-A160
16 NZMB1-1-AF16
1)
number

Shunt trip 110V240VAC for NZMLW/NLW SNT4LP11K
Undervoltage release 240VAC for NZMLW/NLW UVH4LP11K

number



number
EPBNCX250 Corner filler boxes

number

Din modules number


number
Frequency

enclosure included

Frequency
1)
number

number
Cable size summary

Incoming cables
MCCB or switch disconnector size max/type 2 x 300mm2/M10 bolt
Neutral M12
Earth M10
Outgoing cables
NZM1 MCCB size max / type 70mm2/cable clamp. (95mm2 can be fitted depending on cable manufacturer)
Neutral size max / type 50mm2 tunnel terminals and 4 x M8 bolts
Earth size max / type 50mm2 tunnel terminals and 8 x M8 bolts

Panelboards to IEC61439-2. Form 3b Type 2 8, or 12 outgoing TP ways
Busbar system KEMA certified 50kA Icc, Icw 50kA 1s Outgoing devices; these panelboards utilise three frame
IP3X construction sizes of MCCB: NZM3 250A -400A, NZM2 125A250A
TP, and NZM1 SP 16A125A or TP 20A160A
Outgoing MCCBs to IEC60947-2. kA ratings
shown are Ics=Icu at 400V ac Tinplated busbars
Incoming MCCB/circuit breaker switch to Can be configured for incomer device at top of panelboard
IEC60947-2 Icu 50kA, Ics 25kA Removable side gland plates as standard
Door lock included

Incoming rating 800A, NZMLW MCCB or NLW CBS 800 8 (2 x 400A + 2 x 250A + 4 x 160A) EPBN3880
outgoing ratings up to 400A 12 (2 x 400A + 4 x 250A + 6 x 160A) EPBN31280
NZMLW-800 MCCB incoming device

50kA
Thermal trip fixed at 800A, Magnetic trip adjustment 2 to 8 x In
type (A) Short circuit rating 50kA
3-pole NZMLW MCCB 800 NZMLW-A800

4-pole (3 phase and switched neutral) NZMLW MCCB 800 NZMLW-4-A800
NLW-800 Circuit breaker switch incoming device

50kA
type (A) number
3-pole NLW Circuit breaker switch 800 NLW-800

4-pole NLW Circuit breaker switch 800 NLW-4-800

(A) number

Adapter kit for use when incomer device mounted at top of panelboard 720 EPBKTFSLW1)
1)

Memshield 3 panelboards and associated devices
NZMN3-A400-BT Outgoing devices NZM3 frame MCCBs.
(A) Triple pole 50kA
250 NZMN3-A250-BT
320 NZMN3-A320-BT
400 NZMN3-A400-BT



and NZMB1-A160
16 NZMB1-1-AF16
1)
number

Shunt trip 110V240VAC for NZMLW/NLW SNT4LP11K
Undervoltage release 240VAC for NZMLW/NLW UVH4LP11K


number


number

number

Din modules number


number
Frequency

Memshield 3 panelboards and associated devices
enclosure included

Includes CT to meter plug-in cable and meter to meter voltage supply linking cable with connectors. EPBCTMT400
Frequency
1)
number

number
Cable size summary

Incoming cables
MCCB or switch disconnector size max/type 2 x 300mm2/M12 bolt
Neutral M12
Earth M10
Outgoing cables
NZM2 MCCB size max /type 185mm2/cable clamp
NZM1 MCCB size max /type 70mm2/cable clamp. (95mm2 can be fitted depending on cable manufacturer)
Earth size max/type 50mm2 tunnel terminals and 8 x M8 bolts

Plug-in incoming metering
When configuring panelboard incoming metering, simply Meter connection arrangement

identify panelboard and incomer type, then order the
following modules detailed in the selection chart below-
1. Incoming meter connection kit
2. Incoming meter enclosure
3. Meter
4. Voltage supply to meter tap-off kit
5. Top or bottom mounted cable extension
box (When necessary see note)
Plug-in connectivity is provided between meter, CT and supply.
Incoming metering can be configured with outgoing metering.
Incoming metering module selection

Meter module Panelboard E PBN1425, EPBN1625, EPBN1825, EPBN11225 EPBN1640, EPBN11240 E PBN2640, EPBN21240, EPBN21840
250A 3P 250A 4P 250A 3P 400A 3P 400A 4P 400A 3P 400A 3P 400A 4P 400A 3P
MCCB/switch MCCB/switch lugs MCCB/switch MCCB/switch lugs MCCB/switch MCCB/switch lugs
Incoming metering EPBKN1253M

connection kit EPBKN1254M
EPBKN125LM
EPBKN2403M
EPBKN2404M
EPBKN240LM
Incoming meter enclosure EPBN1EX250M
EPBN2EX250M
Meter EPBMETER1
Voltage supply to EPBN1SUPM
meter tap-off kit EPBN3SUPM
Cable extension box1) EPBN2EX250
Meter module Panelboard E PBN2863, EPBN21263, EPBN21863 EPBN3880, EPBN31280
630A 3P 630A 4P 630A 3P 800A 3P 800A 4P
MCCB/switch MCCB/switch lugs MCCB/switch MCCB/switch
Incoming metering EPBKN2633M

connection kit EPBKN2634M
EPBKN3803M
EPBKN3804M
EPBKN263LM
Incoming meter enclosure EPBN3EX250M
Meter EPBMETER1
meter tap-off kit
Cable extension box1) EPBN3EX250
1)
When incoming meter enclosure is fitted at the feed end of the panelboard there is no need for a cable extension box

Plug-in incoming metering 5.6
Meter
Meter is available with pulsed and modbus outputs.
Simply installed with 2 locking screws.
Incoming meter enclosure

250mm high enclosure with hinged front door.
Simply bolted to the top or the bottom of the panelboard.
Supply tap-off
Provision to fit tap-off to either the left and/or right hand side of the pan assembly.
Only 1 per panelboard is required but provision to fit two is an option.
Incoming metering connection kit

This includes all copper connectors, CT, shielding and CT
to meter cable. Can be top or bottom fed.
This does not include the incoming device, which has to be ordered separately.
Cable extension box (when necessary)

250mm high enclosure, fitted incoming end.
When incoming meter enclosure is fitted at the feed end of the
400A/630A/800A boards there is no need for a cable extension box.

Plug-in outgoing metering
When configuring panelboard outgoing metering, simply identify Meter connection arrangement
panelboard and number of outgoing breaker type, then order
the following modules detailed in the selection chart below:
1. Outgoing CT kit
2. Outgoing side mounted meter extension box
3. Meter
4. Voltage supply to meter tap-off kit
5. Extra long meter to meter voltage linking kit to feed to meter
extension box on other side of panelboard if necessary
6. Extra long CT to meter linking cable if required
7. Three phase splitter box to allow separate monitoring of a three
phase current transformer on individual energy meters if required
Plug-in connectivity is provided between meter, CT and supply.
Outgoing metering can be configured with incoming metering.
EPBN11225
EPBN11240
EPBN21240
EPBN21840
EPBN21263
EPBN21863
EPBN31280
EPBN1425
EPBN1625
EPBN1825
EPBN1640
EPBN2640
EPBN2863
EPBN3880
Outgoing metering module selection
Meter module Panelboard
Outgoing CT kit EPBCTMT160 (NZM1 160A)

(1 off required per EPBCTMT250 (NZM2 250A)
outgoing way)
EPBCTMT400 (NZM3 400A)
Outgoing side mounted EPBN1425SXM
meter extension box
EPBN1625SXM
EPBN1825SXM
EPBN11225SXM
EPBN2640SXM
EPBN21240SXM
EPBN21840SXM
EPBN21263SXM
EPBN21863SXM
Meter EPBMETER1
meter tap-off kit EPBN3SUPM
CT mount for outgoing EPBSXBCTMT
meter cable way 1)
Extra long meter to meter EPBN3LKKTM
voltage linking kit
Extra long CT to meter EPBN3LKRJ45
linking kit
Three phase splitter box EPBCTMT3P
1)
Only required when terminal shields are fitted to outgoing MCCBs. The CT can be fitted in a side-mounted cable extension box. One CT mount per outgoing CT.

Plug-in outgoing metering 5.7
Meter Outgoing meter kit
Meter is available with pulsed and modbus outputs. One kit per outgoing way, includes
Simply installed with 2 locking screws. CT, CT to meter cable, and meter
to meter voltage linking cable.
NZM1 160A max
NZM2 250A max
NZM3 400A max
Outgoing side mounted

meter extension box
Can be fitted on the left and right
hand side of the panelboard.
All outgoing meter apertures, except one,
have removable blanking shields fitted.
Three phase splitter box

Allows for separate monitoring of
a three phase current transformer Supply tap-off
on individual energy meters Provision to fit tap-off to either the left and/or right hand side of the pan assembly.
Only 1 per panelboard is required but provision to fit two is an option.
Extra long meter to meter voltage linking kit

Extra long CT to meter linking cable Required when:
Required when CT is fitted on opposite side to meter extension box. 2.5m long. Incoming and outgoing metering on one side = 1 off
Outgoing metering on both sides = 2 off
Incoming and outgoing metering on both sides = 3 off
2m long

Lightning & surge suppression for MCCB panelboards
In order to enable designers, specifiers, and installers to comply EPBN1SPD1234 technical summary:
with surge protection requirements in BS 7671 - IET Wiring
For the protection of low voltage distribution systems
Regulations - 17th Edition (Section 534), these combined
against direct lightning strike into the overhead power
lightning arrester and surge suppression devices have been
supply line or external lightning protection system and
developed specifically for applications with MCCB panelboards
against indirect lightning strike and switching operations.
ensuring outstanding product performance for all sensitive,
mission critical and general purpose loads. Providing protection Application according to IEC 60364-5-53 Clause 534.
from direct and indirect lightning strikes, the IEC 61643 Test class I, II, III in accordance with IEC 61643-1.
tested devices have impressive voltage protection levels (Up),
nominal discharge current (8/20) s In & maximum discharge
current Imax for transient surge suppression, combined with No discharge of ionised gases during operation.
impulse current Iimp (10/350) s for lightning strike protection. Lightning protection classes I, II, III and IV
These devices are fully compliant with BS EN 62305. in accordance with IEC 62305.
EPBN1SPD123 technical summary:

For the protection of low voltage distribution systems
against transient overvoltage caused by direct and
indirect lightning strike and switching operations.
Lightning protection classes III and IV in
accordance with IEC 62305.

EPBN1SPD123
number

MCCB pan assemblies 5.9
MCCB pan assemblies, interiors, three Eaton MCCB pan assemblies offer a high degree of
phase, with earth & neutral bars flexibility, suitable for inclusion in other factory built
assemblies and as replacements for panelboard interiors.
For incoming and outgoing device compatibility
see associated panelboard details.
See pages 153-154 for dimensional drawings
EPBPN31280 Product range

Description Current rating Total no of Eaton list
Memshield 3 panelboard pan assembly 250A, 4 Way. Outgoing up to 160A 250 4 EPBPN1425

6
Eatons MEM series products have earned a worldwide

reputation for reliable high quality switch and
fusegear and above all market leading status.
Constantly updated and refined to comply with
the very latest international standards, the market
leading switchgear range, specialist heavy duty
items and dedicated distribution and control
equipment fulfils the diverse requirements of the
contractor, specifier, OEM and distributor alike.
6.1 GLASGOW FUSE-SWITCH-DISCONNECTORS & SWITCH-DISCONNECTORS..................................................................... 94
6.2 GLASGOW BUSBAR CHAMBER SYSTEM................................................................................................................................ 98
6.3 EXEL 2 SWITCH-DISCONNECTORS & SWITCH-DISCONNECTOR FUSES.......................................................................... 100
6.4 ROTARY ISOLATORS AND CHANGEOVER SWITCHES ......................................................................................................... 102
6.5 EXEL DISTRIBUTION FUSEBOARDS.................................................................................................................................... 103

6.1 Industrial switch & fusegear
103GNL Glasgow switch-disconnector

All listed are TPN
Nominal unit Nominal rating, Copper switch Motor ratings AC23A Ue 415V Eaton list
rating, Ie AC21 (A) links fitted kW HP number
63 125 63MLK 22 30 63GNL

100 125 100MLK 22 30 103GNL
160 (use 200A switch-disconnector)
200 315 200MLK 90 125 203GNL
400 630 400MLK 110 150 403GNL
630 1000 630MLK 225 300 603GNL
800 1000 800MLK 300 400 803GNL
Stud size: 63/100A = tunnel terminal, 160/200A = M10, 300/400 = M14, 500/800A = see page 156, copper terminal plate
203GNC Glasgow fuse-switch-disconnector

Units are fitted with HRC Fuselinks of maximum rating but will accept fuselinks of a
lower rating, refer to the Paramount HRC Fuselinks section on page 106.
SPSN and TPSN indicate switched neutral.
Neutral makes first and breaks last.
Nominal unit Eaton 415V Suitable Suitable copper Motor ratings AC23A Ue 415V Poles Eaton list
rating, Ie (A) fuse(s) fitted fuselinks switch links kW HP number
63 63SB4 SB3 & SB4 63MLK 22 30 SPSN 61GNC

1)
DP
TPN 63GNC
TPSN 64GC
100 100SD5 SB3, SB4, SO & SD5 100MLK 22 30 SPSN 101GNC
1)
DP
TPN 103GNC
TPSN 104GC
160 160SF6 SF3 & SF6 200MLK 90 125 SPSN 151GNC
1)
DP
TPN 153GNC
TPSN 154GC
200 200SF6 SF3 & SF6 200MLK 90 125 SPSN 201GNC
1)
DP
TPN 203GNC
TPSN 204GC
315 315SF7 SF3 & SF7 400MLK 110 150 TPN 303GNC
TPSN 304GC
400 400SF8 SF3 & SF8 400MLK 110 150 TPN 403GNC
TPSN 404GC
500 500SH9 SH8 & SH9 630MLK 225 300 TPN 503GNC
630 630SH9 630MLK 225 300 TPN 603GNC
TPSN 604GC
800 800SH10 SH8 & SH10 800MLK 300 400 TPN 803GNC
TPSN 804GC
1)
If DP fuse-switch-disconnectors are required, use SPSN and replace the supplied switch link with a compatible fuselink.
Stud size: 63/100A = tunnel terminal, 160/200A = M10, 300/400 = M14, 500/800A = see page 156, copper terminal plate

Glasgow fuse-switch-disconnectors & switch-disconnectors 6.1
50CSB Spreader boxes
Provide additional space for spreading multi-core PVC insulated cables
Supplied with fixing bolts and plain bushes
Adapter plates required for each unit, see page 96
Nominal unit Eaton list number
rating, Ie (A) Straight 45 angled
63 50CSB 50CSBA
100 50CSB 50CSBA
160/200 60CSB 60CSBA
315/400 70CSB 70CSBA
500/630 90CSB 90CSBA
800 90CSB 90CSBA
Extension boxes
For fitting to Glasgow switch units to provide additional space for spreading multi-core PVC insulated
cables with solid aluminium conductors and for some larger cables with stranded copper conductors
Nominal unit Fuse switch-disconnector/switch-disconnector Eaton list
rating (A) number
63 61GNC 1PCB1)
63GNC/63GNL 2PCB1)
64GC
100 101GNC 1PCB2)
103GNC/103GNL 2PCB2)
104GC
160 151GNC 2PCB3)
153GNC 3PCB3)
154GC
200 201GNC 2PCB
203GNC/203GNL (315A AC21) 3PCB
204GC
315 303GNC 4PCB
304GC
400 403GNC/use 403GNL (630A AC21)
404GC
500 503GNC 5PCB4)
504GC
630 603GNC/use 603GNL (1000A, AC21)
604GC
800 803GNC/use 803GNL (1000A, AC21)
804GC
1)
Not required for copper cables or al. below 35mm2
2)
Not required for copper cables or al. below 50mm2
3)
Not required for copper cables
4)
For parallel cables use 6 PCB + 802 GCC + 2 x 90 CSB or CSBA (see diagram on page 156)

506APL Adapter plate to fit spreader boxes

Available for fitting to spreader boxes, tapped to receive Type B compression glands to BS6121-1.
Supplied complete with fixing bolts
Nominal unit Straight 45 angled Cable mm2 PVC SWA Eaton list
rating, Ie (A) spreader box spreader box stranded cables: number
1)
63 50CSB 50CSBA 16 2-core 4-core
1)
25 2-core 4-core
1)
35 2-core 4-core
1)
100 50CSB 50CSBA 25 2-core 4-core
1)
35 2-core 4-core
1)
50 2-core
4-core 405 APL
1)
160 50CSB 50CSBA 50 2-core
4-core 405 APL
1)
70 2-core
4-core 405 APL
95 2-core 405 APL
4-core 505 APL
1)
60CSB 60CSBA 50 2-core
4-core 406 APL
1)
70 2-core
4-core 406 APL
95 2-core 406 APL
4-core 506 APL
1)
200 50CSB 50CSBA 70 2-core
4-core 405 APL
95 2-core 405 APL
4-core 505 APL
120 2-core 405 APL
4-core 505 APL
1)
60CSB 60CSBA 70 2-core
4-core 406 APL
95 2-core 406 APL
4-core 506 APL
120 2-core 406 APL
4-core 506 APL
150 2-core 4-core 506 APL
300/400 70CSB 70CSBA 150 4-core 507 APL
185 4-core 637 APL
240 4-core 637 APL
300 4-core 757 APL
500/630 90CSB 90CSBA 240 4-core 639 APL
300 4-core 759 APL
400 4-core 759 APL
Parallel cables2) 2/150 4-core 2 x 509 APL2)
2/185 4-core 2 x 639 APL2)
2/240 4-core 2 x 639 APL2)
800 90CSB 90CSBA 2/300 4-core 2 x 759 APL2)
1)
Sufficient spreading space in switch-disconnector units to mount B gland on to enclosure.
2)
For 500 / 630 & 800A unit applications where parallel cables are used you need to order; 6PCB + 802GCC
(copper connection piece) + 2x 90CSB or 90CSBA see configuration on page 156.

Glasgow fuse-switch-disconnectors & switch-disconnectors 6.1
EBK110SP Glasgow spares
Nominal unit Eaton list
rating, Ie (A) number
Moving contact fuse carrier; 1 per pole

63 EBK110SP
100 OBK103SP
160200 EBK105SP
315400 EBK113SP
Fixed contact base complete; 1 per pole
63100 102GCEBSP
160200 202GCEBSP
315400 (2 per pole) 402GCEBSP
Aerosol spray paint, Light grey to RAL7004. Eaton list number: 2AP
PD1 Handle locking devices

Facilities are provided for locking off operating handles
Current rating Eaton list
(A) number
Handle locking 63800 PD11)

1)
Operating handles of all units can be locked ON or OFF using padlock only.

Glasgow busbar chamber system
142BBC Busbar chambers

Nominal unit Nominal length, Eaton list
rating, Ie (A) mm number
142 BBC
100 550
900 143 BBC
1350 144 BBC
1800 146 BBC
242 BBC
200 550
900 243 BBC
1350 244 BBC
1800 246 BBC
442 BBC
400 550
900 443 BBC
1350 444 BBC
1800 446 BBC
643 BBC
630 900
1350 644 BBC
1800 646 BBC
843 BBC
800 900
1350 844 BBC
1800 846 BBC
21BBL Busbar chamber extension sets

Nominal rating, Eaton list
Ie (A) number
630 81 BBL
800 81 BBL
For busbar supports, see page 158 for details
400FSCS Connection sets for Glasgow fuse-switch-disconnectors & switch-disconnectors

Nominal rating, Eaton list
Ie (A) number
160, 200 200 FSCS

315, 400 400 FSCS
500, 630, 800 800 FSCS

Glasgow busbar chamber system 6.2
62BBSK Busbar clamps and sockets 100200A Busbars
Type Nominal rating, Bore diameter Capacity Eaton list
Ie (A) mm mm2 number
U-Clamps 2063 25 2 BBCL

63100 70 3 BBCL
100200 120 6 BBCL
Busbar clamps and lugs connection 400800A Busbars

Type Nominal rating, Bore diameter Capacity Eaton list
Ie (A) mm mm2 number
U-Clamps 2063 25 4 BBCL

63100 70 5 BBCL
100200 120 6 BBCL
Lugs connection 315400 22.5 240 82 BBSK
21BBMS Switchgear mounting sets

Description Nominal rating, Eaton list
Ie (A) number
Exel Switch-disconnector-fuses/ 20, 32 11 BBMS

Switch-disconnectors 63, 100, 125 21 BBMS
Glasgow Fuse-switch-disconnectors/ 63, 100 31 BBMS
Switch-disconnectors 160, 200 41 BBMS
315, 400 51 BBMS
500, 630, 800 61 BBMS

Exel 2 switch-disconnectors & switch-disconnector fuses
15AXTN2 Exel 2 switch-disconnector

Nominal Utilisation category at 250V DC rating Blank Poles Eaton list
rating, Ue 415V to BS EN 60947-3 to BS5419 endplate number
Ie (A) AC22A (A) AC23A (A) DC23 (A)
20 20 201) EP 842 SPSN

DP 15AXD2
11 TPN 15AXTN2
32 32 32 SPSN
DP 30AXD2
22 TPN 30AXTN2
63 63 63 EP 539 SPSN
DP 60AXD2
39 TPN 60AXTN2
100 100 100 SPSN
DP 100AXD2
52 TPN 100AXTN2
125 125 52 TPN 125AXTN2
1)
SPSN indicates switched neutral. 20A units are DC22.
100KXSC2F Exel 2 switch-disconnector-fuse

Nominal Utilisation category at 250V DC rating Blank Eaton Poles Eaton list
rating, Ue 415V to BS EN 60947-3 to BS5419 endplate HRC fuses number
Ie (A) AC22A (A) AC23A (A) (A) fitted DC23
20 20 201) EP 842 20SA2 SPSN 15KXSC2F2)

DP 15KXDC2F
11 TPN 15KXTNC2F
32 32 32 32SB3 SPSN 30KXSC2F
DP 30KXDC2F
22 TPN 30KXTNC2F
63 63 63 EP 539 63SB4 SPSN 60KXSC2F
DP 60KXDC2F
39 TPN 60KXTNC2F
100 100 100 100SD52) SPSN 100KXSC2F
DP 100KXDC2F
52 TPN 100KXTNC2F
125 125 52 125SD62) TPN 125KXTNC2F
1)
SPSN indicates switched neutral. 20A units are DC22.
2)
These units have dual fixings to accept SB3, SB4 and SO fuselinks. 2x M5 screws required

Exel 2 switch-disconnectors & switch-disconnector fuses 6.3
PD4 Handle locking devices
Facilities are provided for locking off operating handles
Current rating Eaton list

(A) number
Handle locking 20125 PD4
Exel 2 Spares
Description Rating Quantity required Eaton list
(A) number
Moving contact assembly 20 1 OLV727SP

32 1 OLV728SP
63 1 OLV725SP
100/125 1 OLV726SP
Switch base with arc shroud 32 1 per pole 230AXEBSP1)
63 1 per pole 260AXEBSP1)
100/125 1 per pole 2100AXEBSP1)
100/125 1 per pole 2100AXDEBSP
Combined switch/fusebase with arc shroud 32 1 per pole 230KXEBSP
63 1 per pole 260KXEBSP
Fusebase only 100/125 1 per pole 100MBDEBSP
Arc shroud only 32 1 per pole SH265SP
63 1 per pole SH754SP
100/125 1 per pole CV1109SP
1)
1 required for switched neutral pole on SPSN switchfuses.
Aerosol spray paint, Light grey to RAL7004. Eaton list number: 2AP
600MEB Main earthing terminal bars

Memform terminal bars are intended for the connection of circuit protective conductors, main bonding
conductors and functional earthing conductors, etc., as referred to in IEE Wiring Regulation 542-04 (BS7671)
A bolted link facilitates testing of earthing resistance
Manufactured from solid hard drawn copper and mounted on painted steel
supports complete with fixing holes and warning labels
For ease of installation all terminals are captive
Extra terminals are provided for supplementary bonding
Maximum Size and number of terminals Overall Overall Copper Eaton list
incomer, Earthing Protective length width thickness number
Ie (A) bonding mm mm mm
600 1 x M10 3 x M10 320 32 31.75 x 6.35 600MEB

2 x M6
1000 2 x M12 3 x M12 665 51 50.8 x 6.35 1000MEB
1 x M8 8 x M8

Rotary isolators & changeover switches
See pages 163-164 for technical data and overall dimensions.
xxxxx
207149-GV Rotary isolators
20A to 63 A
IP65
Red/yellow handle
Lockable in the 0 (Off) position
Surface mounting
IEC 60947-3
Rated current Iu (A) Motor rating AC-23A, 400V, Poles Auxiliary contact Eaton
50 - 60 Hz (kW) List Number
20 6.5 3 1 NO 207149-GV
20 6.5 3+N 207151-GV
20 6.5 3+N 1 NO + 1 NC 207153-GV
20 6.5 6 1 NO + 1 NC 207161-GV
25 13 3 1 NO + 1 NC 226902-GV
25 13 3+N 227860-GV
32 13 3+N 1 NO + 1 NC 207202-GV
32 13 6 1 NO + 1 NC 207210-GV
32 13 8 207212-GV
63 30 3 1 NO + 1 NC 207348-GV
63 30 3+N 207349-GV
63 30 3+N 1 NO + 1 NC 207350-GV
63 22 6 1 NO + 1 NC 207246-GV
63 22 8 207248-GV
Changeover switches
20A to 63 A
IP65
Black handle
Surface mounting
IEC 60947-3
Rated current Iu (A) Motor rating AC-23A, 400V, Poles Eaton List
50 - 60 Hz (kW) Number
20 6.5 207136-GV
4
32 13 207191-GV
4
63 22 207230-GV
4

Exel distribution fuseboards 6.5
304XTNC Exel distribution fuseboards

Nominal Poles No. of Max. terminal Outgoing Suitable Spare Safety Eaton list
rating, Ie (A) ways capacity mm2 terminal bore HRC fuse carrier number
(copper cables) diameter, mm fuselinks carrier (without fuselinks)
Main Outgoing
IP4X enclosures
20 SPN 4 95 6 4 SA2 20 MFH 20 MFS 204XSNC
6 95 6 4 SA2 20 MFH 20 MFS 206XSNC
8 120 6 4 SA2 20 MFH 20 MFS 208XSNC
12 120 6 4 SA2 20 MFH 20 MFS 212XSNC
TPN 4 95 6 4 SA2 20 MFH 20 MFS 204XTNC
6 95 6 4 SA2 20 MFH 20 MFS 206XTNC
8 120 6 4 SA2 20 MFH 20 MFS 208XTNC
32 SPN 4 95 16 5.5 SB3 32 MFH 32 MFS 304XSNC
6 95 16 5.5 SB3 32 MFH 32 MFS 306XSNC
8 150 16 5.5 SB3 32 MFH 32 MFS 308XSNC
12 150 16 5.5 SB3 32 MFH 32 MFS 312XSNC
TPN 4 95 16 5.5 SB3 32 MFH 32 MFS 304XTNC
6 95 16 5.5 SB3 32 MFH 32 MFS 306XTNC
8 150 16 5.5 SB3 32 MFH 32 MFS 308XTNC
10 150 16 5.5 SB3 32 MFH 32 MFS 310XTNC
12 150 16 5.5 SB3 32 MFH 32 MFS 312XTNC
63 TPN 2 240 35 8 SB3 & SB4 63 MFH 63 MFS 602XTNC
4 240 35 8 SB3 & SB4 63 MFH 63 MFS 604XTNC
6 240 35 8 SB3 & SB4 63 MFH 63 MFS 606XTNC
8 240 35 8 SB3 & SB4 63 MFH 63 MFS 608XTNC
100 TPN 4 240 70 12 SD51) 100 MFH 100 MFS 1004XTNC
6 5002) 70 12 SD51) 100 MFH 100 MFS 1006XTNC
2)
8 500 70 12 SD51) 100 MFH 100 MFS 1008XTNC
2)
200 TPN 4 630 150 18 SF6 200 MFH 200 MFS 2004XTNC
All units are supplied without fuselinks which must be ordered separately.
1)
SB3, SB4 and SO fuselinks may be fitted if used with adaptor Eaton list number 100MFLK.
1)
Can be adapted to allow fitment of 2240mm2 max. cable sockets with suitable copper spacing piece Eaton list number WA1212 (set of 4).
8LD Lid locking facilities

A choice of locking device is available
number
Barrel lock for 20A to 100A units 1CLX

Padlock bracket for 20A to 100A units 9LD
Padlock for use with above PD1

Exel distribution fuseboards
ETM2209SP Exel distribution fuseboard spares

Description Boards SP outgoing ways Eaton list
number
Earth bars 20/32A fuseboards up to 12 ETM2209SP

up to 18 ETM2210SP
up to 24 ETM2211SP
up to 36 ETM2212SP
Neutral bars 20/32A fuseboards up to 12 ETM2223SP
up to 18 ETM2224SP
up to 24 ETM2225SP
up to 36 ETM2226SP

HRC cartridge fuselinks and fuse units
7
Options to suit every application

Compact 415V fuselinks
Breaking capacity of 80kA at 415V
Motor rated fuselinks
Compact moulded HRC fuse units
Fully shrouded for safety
For bolt-in & clip-in fuselinks
7.1 PARAMOUNT........................................................................................................................................................................... 106
7.2 FUSE CARRIERS & BASES....................................................................................................................................................... 112

7.1 HRC cartridge fuselinks and fuse units
Paramount
See page 161 for overall dimensions.
10SA2 415V industrial fuselinks offset bolted contacts

S-Type compact industrial bolted pattern fuselinks with offset contacts. ASTA 20 Certified
BSEN 60269-1 (BS88 1) or BS88 2 for a breaking capacity of 80 kA at 415V a.c.
Fixing BS88 ref Rating, In Dimensional equivalents Eaton list
centres, mm Normal Motor GEC/Lawson Brush/Hawker Bussmann/ number
(A) (A) Dorman
44.5 A1 2 NIT2 2F21 NITD2 2SA2

4 NIT4 4F21 NITD4 4SA2
6 NIT6 6F21 NITD6 6SA2
10 NIT10 10F21 NITD10 10SA2
16 NIT16 16F21 NITD16 16SA2
20 NIT20 20F21 NITD20 20SA2
25 NIT20M25 20M25F21 NITD20M25 20SA2M25
32 NIT20M32 20M32F21 NITD20M32 20SA2M32
25 NIT25 25F21 NITD25 25SA2
32 NIT32 32F21 NITD32 32SA2
40 NIT32M40 NITD32M40 32SA2M40
20SB3 73 A2 2 TIA2 2HO7 AAO2 2SB3
4 TIA4 4HO7 AAO4 4SB3
6 TIA6 6HO7 AAO6 6SB3
10 TIA10 10HO7 AAO10 10SB3
16 TIA16 16HO7 AAO16 16SB3
20 TIA20 20HO7 AAO20 20SB3
25 TIA25 25HO7 AAO25 25SB3
32 TIA32 32HO7 AAO32 32SB3
40 TIA32M40 32M40HO7 AAO32M40 32SB3M40
50 TIA32M50 32M50HO7 AAO32M50 32SB3M50
63 TIA32M63 32M63HO7 AAO32M63 32SB3M63
63SB4 A3 35 TIS35 35SB4
40 TIS40 40KO7 BAO40 40SB4
50 TIS50 50KO7 BAO50 50SB4
63 TIS63 63KO7 BAO63 63SB4
80 TIS63M80 63M80KO7 BAO63M80 63SB4M80
100 TIS63M100 63M100KO7 BAO63M100 63SB4M100
80 OS80/TIS80 80KO7R OSD80 80SO
100 OS100/TIS100 100KO7R OSD100 100SO
125 OS100M125/ OSD100M125 100SOM125
TIS100M125
160 OSD100M160 100SOM160
125 OOT125 125S0
160 00T160 160SO
200 200SO
100SD5 94 A4 32 TCP32 32L14 CEO35 32SD5
40 TCP40 40L14 CEO40 40SD5
50 TCP50 50L14 CEO50 50SD5
63 TCP63 63L14 CEO63 63SD5
80 TCP80 80L14 CEO80 80SD5
100 TCP100 100L14 CEO100 100SD5
125 TCP100M125 100M125L14 100SD5M125
CEO100M125
160 TCP100M160 100M160L14 100SD5M160
CEO100M160
200 TCP100M200 100M200L14 100SD5M200
CEO100M200

Paramount 7.1
415V industrial fuselinks offset bolted contacts (contd)
Fixing BS88 ref Rating, In Dimensional equivalents Eaton list
centres, mm Normal Motor GEC/Lawson Brush/Hawker Bussmann/ number
(A) (A) Dorman
125 TFP125 125M14 DEO125 125SD6

160 TFP160 160M14 DEO160 160SD6
200 TFP200 200M14 DEO200 200SD6
250 TFP200M250
200M250M14 200SD6M250
DEO200M250
315 200SD6M315
These industrial bolted pattern fuselinks are of two types with offset contacts of ratings 2200A and with centre contacts of ratings 21250A.
They are available to BS references A1 to A4, B1 to B4, C1 to C3, D1 and in certain other sizes.
20SE3 415V industrial fuselinks centre bolted contacts

S-Type compact industrial bolted pattern fuselinks with centre contacts. ASTA 20 Certified or
tested to BS EN 60269-1 (BS88-1) or BS88-2 for a breaking capacity of 80 kA at 415V a.c.
Fixing BS88 ref Rating In Dimensional equivalents Eaton list
centres, mm Normal (A) Motor GEC/Lawson Brush/Hawker Bussmann/Dorman number
97 2 TB2 2KO8 AC2 2SE3

4 TB4 4KO8 AC4 4SE3
6 TB6 6KO8 AC6 6SE3
10 TB10 10KO8 AC10 10SE3
16 TB16 16KO8 AC16 16SE3
20 TB20 20KO8 AC20 20SE3
25 TB25 25KO8 AC25 25SE3
32 TB32 32KO8 AC32 32SE3
111 2 TBC2 2KO9 AD2 2SF3
4 TBC4 4KO9 AD4 4SF3
6 TBC6 6KO9 AD6 6SF3
10 TBC10 10KO9 AD10 10SF3
16 TBC16 16KO9 AD16 16SF3
20 TBC20 20KO9 AD20 20SF3
25 TBC25 25KO9 AD25 25SF3
32SF3 32 TBC32 32KO9 AD32 32SF3
97 40 TB40 40KO8 BC40 40SE4
50 TB50 50KO8 BC50 50SE4
63 TB63 63KO8 BC63 63SE4
97 63 80 63SE4M80
100 63SE4M100
111 B1 40 TBC40 40KO9 BD40 40SF4
50 TBC50 50KO9 BD50 50SF4
63 TBC63 63KO9 BD63 63SF4
80 63SF4M80
100 63SF4M100
80 TC80 80LO9 CD80 80SF5
100 TC100 100LO9 CD100 100SF5
125 TC100M125
100M125LO9 100SF5M125
CD100M125
160 TC100M160
100M160LO9 100SF5M160
CD100M160
200 TC100M200
100M200LO9 100SF5M200
CD100M200
B2 125 TF125 125MO9 DD125 125SF6
160 TF160 160MO9 DD160 160SF6
200SF6 200 TF200 200MO9 DD200 200SF6
250 TF200M250
200M250M09 200SF6M250
DD200M250
315 200SF6M315
B3 250 TKF250 250NO9 ED250 250SF7
315 TKF315 315NO9 ED315 315SF7
400 315SF7M400
133 250 TKM250 250N11 EFS250 250SG7
315 TKM315 315N11 EFS315 315SG7

Paramount
400SH8 415V industrial fuselinks centre bolted contacts (contd)

Fixing BS88 ref Rating In Dimensional equivalents Eaton list
centres, mm Normal (A) Motor (A) GEC/Lawson Brush/Hawker Bussmann/Dorman number
111 B4 355 TMF355 355PO9 ED355 355SF8

400 TMF400 400PO9 ED400 400SF8
500 TMF400M500
ED400M500 400SF8M500
133/184 C1 355 TM355 355P11 EF355 355SH8
400 TM400 400P11 EF400 400SH8
133/184 C2 450 TTM450 450R11 FF450 450SH9
630SY9 500 TTM500 500R11 FF500 500SH9
560 TTM560 560R11 FF560 560SH9
630 TTM630 630R11 FF630 630SH9
165/229 450 TT450 450R12 FG450 450SY9
500 TT500 500R12 FG500 500SY9
630 TT630 630R12 GG630 630SY9
133/184 C3 710 TLM710 700S11 GF710 710SH10
800 TLM800 800S11 GF800 800SH10
165/229 710 TLT710 700S12 GG700 710SY10
1250SJ11 800 TLT800 800S12 GG800 800SY10
149 D1 1000 TXU1000 1000U44 GH1000 1000SJ11
1250 TXU1250 1250U44 GH1250 1250SJ11
20SN2 SN type offset blade fuselinks

ASTA 20 Certified or tested to BS EN 60269-1 (BS88-1) and BS88-6 for a breaking capacity
of 80 kA at 415V a.c. For use in industrial and commercial installations.
Overall Overall Rating In Equivalents Eaton list
length, mm dia. mm Normal (A) Motor (A) GEC/Lawson Brush/Hawker Bussmann/Dorman number
60 14 2 NS2 2FO6 NSD2 2SN2

4 NS4 4FO6 NSD4 4SN2
6 NS6 6FO6 NSD6 6SN2
10 NS10 10FO6 NSD10 10SN2
16 NS16 16FO6 NSD16 16SN2
20 NS20 20FO6 NSD20 20SN2
25 NS20M25
20M25FO6 20SN2M25
NSD20M25
32 NS20M32
20M32FO6 20SN2M32
NSD20M32
25 NS25 25FO6 NSD25 25SN2
32 NS32 32FO6 NSD32 32SN2
58 17.5 32 40 NS32M40 NSD32M40 32SN2M40
50 NS32M50
NSD32M50 32SN2M50
63 NS32M63
NSD32M63 32SN2M63

Paramount 7.1
63SP SP type offset blade fuselinks
ASTA 20 Certified to BS EN 60269-1 (BS88 1) and BS88 6 for a breaking capacity
of 80 kA at 415V a.c. For use in industrial and commercial installations.
Overall Overall Rating In Equivalents Eaton list
length, mm dia. mm (A) GEC/Lawson Brush/Hawker Bussmann/Dorman number
68 17 16 ESD16 16SP
20 ESD20 20SP
25 ESD25 25SP
32 ESD32 32SP
40 40ES 40GO5 ESD40 40SP
50 50ES 50GO5 ESD50 50SP
63 63ES 63GO5 ESD63 63SP
604R R and RL type house service cut-out fuselinks

Type IIa (R) and IIb (RL) house service cut-out fuselinks. ASTA 20 Certified or tested to BS88-3 for a breaking capacity
of 33 kA at 415V a.c. For use in domestic and commercial installations mainly in supply authorities cut-outs.
Overall Overall Rating, In Equivalents Eaton list
length, mm dia. mm Normal (A) GEC/Lawson Brush/Hawker Bussmann/Dorman number
57 22.23 15 RHF15 15KR85 154R

20 RHF20 20KR85 204R
30 RHF30 30KR85 RHD30 304R
40 RHF40 40KR85 RHD40 404R
45 45KR85 454R
50 RHF50 50KR85 RHD50 504R
60 RHF60 60KR85 RHD60 604R
80 RHF80 80KR85 RHD80 804R
100 100KR85 1004R
57 30 30 RHL30 30LR85 RHLD30 304RL
60 RHL60 60LR85 RHLD60 604RL
80 RHL80 80LR85 RHLD80 804RL
100 RHL100 100LR85 1004RL
RHLD100

Paramount
6LS LS type street lighting fuselinks

ASTA 20 Certified to BS EN 60269-1 (BS88-1) for a breaking capacity of 50kA at 240V a.c.
Also compies with BS7654 for use in street ligting cut-out.
Fixing Overall Overall Rating, In Equivalents1) Eaton list
centres, mm length, mm dia. mm (A) GEC Brush Dorman/Bussmann number
LS-Type, offset contacts

38 47 14 2 LST2 2D19L STD2 2LS
4 LST4 4D19L STD4 4LS
6 LST6 6D19L STD6 6LS
10 LST10 10D19L STD10 10LS
16 LST16 16D19L STD16 16LS
20 LST20 20D19L STD20 20LS
25 LST25 25D19L STD25 25LS
32 LST32 32D19L STD32 32LS
1)
Equivalent columns list fuselinks having similar ratings and fixing centres.
20SS SS type offset blade fuselinks

ASTA 20 Certified to BS EN 60269-1 (BS88-1) for a breaking capacity of 50kA at 240V a.c.
Also compies with BS7654 for use in street ligting cut-out.
Fixing Overall Overall Rating, Equivalents1) Eaton list
centres, mm length, mm dia. mm In (A) GEC Brush Dorman/Bussmann number
51 12 2 SS2 2DO4 SSD2 2SS

4 SS4 4DO4 SSD4 4SS
6 SS6 6DO4 SSD6 6SS
10 SS10 10DO4 SSD10 10SS
16 SS16 16DO4 SSD15 16SS
20 SS20 20DO4 SSD20 20SS
25 SS25 25DO4 SSD25 25SS
32 SS32 32DO4 SSD32 32SS
1)
Equivalent columns list fuselinks having similar ratings and fixing centres.

Paramount 7.1
315JCS82 J type feeder pillar fuselinks
ASTA 20 Certified or tested to BS88 2 (formerly BS88: Part 5) for a breaking capacity of 80 kA at 415V a.c.
Available in standard 82mm and 92mm fixing centres up to 400A and 800A respectively for wedge
tightening contacts. Also available in ferrule form up to 250A for pole mounted cut-outs.
For use by the Electricity Supply Industry in distribution systems.
Available with silver elements, details on request.
Fixing Equivalents Rating, Eaton list
centres, mm Fluvent Lawson SIBA GEC EMP Dorman Bussmann/ In (A) number
Brush
82 DL2-2 JPU 5002301 JP 2/EJA JPD MJ30 63 63JCS82

80 80JCS82
100 100JCS82
125 125JCS82
160 160JCS82
200 200JCS82
250 250JCS82
315 315JCS82
PJ30 355 355JCS82
400 400JCS82
400JCS92 92 DL3-2 JSU 5002601 JS 3/EJB JSD MJ31 63 63JCS92
80 80JCS92
100 100JCS92
125 125JCS92
160 160JCS92
200 200JCS92
250 250JCS92
315 315JSC92
PJ31 355 355JCS92
400 400JCS92
RJ31 450 450JCS92
500 500JCS92
SJ31 560 560JCS92
630 630JCS92
710 710JCS92
800 800JCS92

Fuse carriers and bases
3SCHF Fuse carriers

Nominal Fuse type fitted Eaton list number
rating Ie (A) HRC Fuse Carrier
10 10SA2 1 SCHF
20 20SA2 2 SCHF
32 32SB3 3 SCHF
63 63SB4 6 SCHF
100 100SD5 100SCHF

20MFA Complete fuse units (carriers and bases) bolt-in type A (front/busbar)
Nominal Colour Neutral link Suitable Eaton Eaton list
rating, In (A) HRC fuselinks number
20 Black 20MLK 2-20SA2 20MFA

32 Black 32MLK 2-32SB3 32MFA
63 Black 63MLK 35-63SB4 or 2-32SB3 63MFA
100 Black 100MLK 32-100SD51) 100MFA
1)
SB3, SB4 or SO fuselinks may be fi tted if used with adaptor Eaton list number: 100MFLK.
32MFB Complete fuse units (carriers and bases) bolt-in type B (front/front)
20 Black 20MLK 2-20SA2 20MFB

32 Black 32MLK 2-32SB3 32MFB
63 Black 63MLK 35-63SB4 or 2-32SB3 63MFB
100 Black 100MLK 32-100SD51) 100MFB
Compact range
32 Black 20MLK 2-32SA2 32CMFB
63 Black 32MLK 35-63SB4 or 2-32SB3 63CMFB
100 Black 63MLK 80-100SO or 35-63SB4 100CMFB
200 Black 100MLK 125-200SD6 or 32-100SD5 200CMFB
1)
SB3, SB4 or SO fuselinks may be fitted if used with adaptor Eaton list number: 100MFLK.
63MFC Complete fuse units (carriers and bases) bolt-in type C (back/back)
Nominal Colour Suitable Eaton Eaton list
20 Black 20MLK 2-20SA2 20MFC

63 Black 63MLK 35-63SB4 or 2-32SB3 63MFC
100 Black 100MLK 32-100SD51) 100MFC
Compact range
100 Black 63MLK 80-100SO or 35-63SB4 100CMFC
1)
SB3, SB4 or SO fuselinks may be fitted if used with adaptor Eaton list number: 100MFLK.

Fuse carriers and bases 7.2
63MFD Complete fuse units (carriers and bases) bolt-in type D (front/back)
32 Black 32MLK 2-32SB3 32MFD

63 Black 63MLK 35-63SB4 or 2-32SB3 63MFD
32CFF Complete fuse units (carriers and bases) clip-in type

Nominal Colour Suitable Eaton HRC fuselinks Eaton list
rating, In (A) number
Front/Front
32 Black 2-32SN2 32CFF
White 2-32SN2 32CFFW
63 Black 16-63SP 63CFF
White 16-63SP 63CFFW

8
Since the late 1920s we have built countless

motor starters, fitted and trusted by generations of
contractors, while the increasing requirements of
our markets have led us to constantly update and
expand our ADS range to allow for an increased
choice of current ratings and ingress protection.
This wealth of experience and expertise in the
design and manufacture of Motor Control Gear is
mirrored by our Heating and Lighting range which
offers a versatile and comprehensive choice.
8.1 ADS8 AC CONTACTORS, STARTERS AND ASSEMBLIES...................................................................................................... 116
8.2 PUSHBUTTON CONTROL UNITS MSU ............................................................................................................................... 118
8.3 AUTOLINE HEATING AND LIGHTING CONTACTORS............................................................................................................ 119

8.1 Enclosed motor, heating and lighting control
ADS8 AC contactors, starters and assemblies
This chapter covers the ADS8 range of DOL, DOL Reversing and See page 117 for overload relays.
Star Delta starters with associated overload relays. Overload See page 176 for trip and electrical life curves.
relays are supplied separately and enclosures are IP54 metal clad. See page 166 for dimensional drawings.
A higher rated IP65 moulded 9kW DOL starter is also available.
IEC / EN60947-4
28ADSM1X 9kW DOL starter without switch disconnect

IP 65 moulded surface mounting enclosure, less overload relay
Maximum current rating Maximum kW rating AC3 Control coil voltage 50Hz Eaton list
(AC3) A 415v 3ph Vac number
18 9 220240 28ADSM1X
380415 48ADSM1X
28ADS2X 11kW DOL starter without switch disconnect

IP 54 metalclad surface mounting enclosure, less overload relay
18 9 220240 28ADS1X
380415 48ADS1X
25 11 220240 28ADS2X
380415 48ADS2X
28ADSA1X 11kW DOL starter with switch disconnect

18 9 220240 28ADSA1X
380415 48ADSA1X
25 11 220240 28ADSA2X
380415 48ADSA2X
48ARD1X 11kW DOL Reversing starter without switch disconnect

18 9 220240 28ARD1X
380415 48ARD1X
25 11 220240 28ARD2X
380415 48ARD2X

ADS8 AC contactors, starters and assemblies 8.1
28SDA2X18 22kW Star Delta starter without switch disconnect
31 15 220240 28SDA2X18
380415 48SDA2X18
43 22 220240 28SDA3X25
380415 48SDA3X25
8TT92 DOL, DOL reversing, line connected thermal overload relays

Full load current Motor rating Eaton list
A kW number
0.631 0.37 8TT87

11.6 0.55 8TT88
1.62.5 1.1 8TT89
2.54 1.5 8TT90
46 2.2 8TT91
5.58 3.7 8TT98
710 4 8TT92
1013 5.5 8TT93
1318 9 8TT94
1825 11 8TT104
8TT92SD Star Delta, phase connected thermal overload relays

Full load current Motor rating Eaton list
A kW number
4.36.9 3 8TT90SD
6.910.4 5.5 8TT91SD
9.513.8 7 8TT98SD
12.117.3 9 8TT92SD
17.322.5 11 8TT93SD
22.531 15 8TT94SD
3143 22 8TT104SD

8.2 Enclosed motor, heating and lighting control
Pushbutton control units
This chapter covers the moulded IP66

pushbutton control units type MSU
IEC / EN60947-4
Surface mounting
M22MSU MSU pushbutton control units (moulded IP66)

Number Description Contacts Button Colour Cover Colour Eaton
buttons List Number
1 Start control 1 N/O, 1 N/C Green Light Grey M21MSSU

1 Stop control 1 N/O, 1 N/C Red Yellow M21MSU
1 Key selector switch, 2 position, 0/1 1 N/O Black Light Grey M21MSU2K
1 Key selector switch, 2 position, 0/1, spring return 1 N/O, 1 N/C Black Light Grey M21MSU2SK
1 Mushroom head, push to latch, key release 1 N/C Red Light Grey M21MSULK
1 Stop control, mushroom head, push to latch, 1 N/O, 1 N/C Red Yellow M21MSUML
turn to release
2 2-way, start / stop 1 N/O, 1 N/C (each button) Green / red Light Grey M22MSU
2 2-way, start / stop mushroom head, push to latch, 1 N/O, 1 N/C (each button) Green / red Light Grey M22MSUL
turn to release
3 3-way, up / down / stop mushroom head, push to latch, 1 N/O, 1 N/C (each button) Black / black / red Light Grey M23MSUL1)
turn to release
1)
M23MSUL units are supplied with 2 sets of button legends, FORWARD, REVERSE, and UP, DOWN to be clipped on the buttons as required.

Autoline heating and lighting contactors 8.3
This chapter covers the range of Autoline heating and lighting See page 174 for overall dimensions.
contactors, in 1 pole, 2 pole and 4 pole configuration, with ratings
at AC1 and AC5a. Metalclad enclosures have an IP55 rating.
IEC / EN60947-4
IEC408
248ALCFP Heating and lighting contactors

Description Cable Coil voltage Heating and general Lighting load, Eaton list
capacity 50 Hz mixed loads, amps per pole number
mm 2 slightly inductive, AC5a
amps per pole AC1
4P enclosed without rectifier 4 220240 25 12 228ALCFP

4P enclosed with rectifier 4 220240 25 12 228ALCFPR
4P enclosed with rectifier 10 220240 40 32 428ALCFPR
2P enclosed without rectifier 16 220240 40 25 228ALCDP
2P enclosed without rectifier 25 220240 64 40 428ALCDP
2P enclosed with rectifier 16 220240 40 25 228ALCDPR
2P enclosed with rectifier 25 220240 64 40 428ALCDPR
1P enclosed without rectifier 50 220240 70 50 228ALCSPN
1P enclosed without rectifier 50 220240 112 50 428ALCSPN
1P enclosed with rectifier 50 220240 70 50 228ALCSPNR
1P enclosed with rectifier 50 220240 112 50 428ALCSPNR

9
Eatons power factor correction products are available

in three types. The economical non-auto low voltage
capacitors are an ideal choice for use in electrical
installations where the total load changes very little from
hour to hour and day to day. For installations where
the load is more variable, Eaton offers 100 standard
and 300 standard and de-tuned products, which
constantly monitor the power factor of the installation
and automatically adjust the correction so that it
accurately matches the instantaneous requirements.
9 Eaton capacitors non-auto range............................................................................................................................................... 122
Eaton capacitors 100 auto......................................................................................................................................................... 122
Eaton capacitors 300 standard............................................................................................................................................... 122
Eaton capacitors 300 detuned................................................................................................................................................ 123

9 Power factor correction capacitors
Non-auto, 100 auto and 300 standard
EP2541E Eaton capacitors non-auto
KVAR Terminal Terminal Earth stud Weight Eaton list

(415V) size ctrs size (Kg) number
25 M8 35 M8 6 EP2541E
50 M8 35 M8 8 EP5041E
75 M10 60 M10 16 EP7541E
100 M10 60 M10 18 EP10041E
MC25M1 Eaton capacitors 100 auto

KVAR Stages Weight Incoming Eaton list
(415V) (Kg) device number
25 1 x 25 20 Fusebase MC25M1
21 Fuseswitch MC25M1S
MCCB MC25M1M
MCCB MC50M2M
MCCB MC75M3M
MCCB MC100M4M
If you require a specific KVAR rating other than the above, please contact Eaton for further details.
MC25M5 Eaton capacitors 300 standard

125 5 x 25 210 Direct connection MC125M5

Fuseswitch MC125M5S
MCCB MC125M5M
Fuseswitch MC150M3S
MCCB MC150M3M
175 3 50 + 1 25 245 Direct connection MC175M4
Fuseswitch MC175M4S
MCCB MC175M4M
Fuseswitch MC200M4S
MCCB MC200M4M
Fuseswitch MC225M5S
MCCB MC225M5M
Fuseswitch MC250M5S
MCCB MC250M5M
Fuseswitch MC275M6S
MCCB MC275M6M
Fuseswitch MC300M6S
MCCB MC300M6M
Applications above 300KVAR are also available, please contact Eaton for further details.

300 detuned 9
MC100M2DT Eaton capacitors 300 detuned
100 2 x 50 230 Direct connection MC100M2DT

Fuseswitch MC100M2SDT
MCCB MC100M2MDT
125 2 x 50 + 1 x 25 240 Direct connection MC125M3DT
MCCB MC125M3MDT
MCCB MC150M3MDT
MCCB MC175M4MDT
MCCB MC200M4MDT
MCCB MC225M5MDT
MCCB MC250M5MDT
MCCB MC275M6MDT
MCCB MC300M6MDT
MCCB MC325M7MDT
MCCB MC350M7MDT
MCCB MC375M8MDT
MCCB MC400M8MDT
MCCB MC425M9MDT
MCCB MC450M9MDT
MCCB MC475M10MDT
MCCB MC500M10MDT
MCCB MC525M11MDT
MCCB MC550M11MDT
MCCB MC575M12MDT
MCCB MC600M12MDT
Applications above 600KVAR are also available. Applications above 400KVAR are also available with an ACB as the protective device
Please contact Eaton for further details.
Technical data
10
10.1 MEMSHIELD 3 TYPE A SPN, TYPE B TPN DISTRIBUTION BOARDS .................................................................................... 126
SPLIT METERED POWER AND LIGHTING BOARD 200A TPN, MEMSHIELD 3 METER PACK ASSEMBLIES ................. 128
MEMSHIELD 3 TYPE A SPN, TYPE B TPN PAN ASSEMBLIES .............................................................................................. 129
SURGE PROTECTION DEVICES ............................................................................................................................................. 131
METER PACK ASSEMBLIES ................................................................................................................................................... 132
18MM MINIATURE CIRCUIT BREAKERS (MCBS) ................................................................................................................. 134
27MM MINIATURE CIRCUIT BREAKERS (FOR 250A HIGH LOAD DISTRIBUTION BOARDS) ........................................... 136
RESIDUAL CURRENT CIRCUIT BREAKERS (RCCBS) ........................................................................................................... 137
RESIDUAL CURRENT CIRCUIT BREAKERS WITH OVERLOAD (RCBOS) ......................................................................... 138
CONTROL AND SWITCHING DEVICES DIMENSIONS AND DATA ...................................................................................... 139
EARTH LEAKAGE RELAYS AND CTS ..................................................................................................................................... 147
10.2 MCCBS, MAX ZS (OHMS) FIGURES ..................................................................................................................................... 148
PANELBOARD DIMENSIONAL DRAWINGS .......................................................................................................................... 149
PANELBOARD MULTIFUNCTION METER, TECHNICAL CHARACTERISTICS AND SPECIFICATION ................................. 152
MCCB PAN ASSEMBLIES, DIMENSIONS............................................................................................................................... 153
10.3 ENCLOSED SWITCH & FUSEGEAR......................................................................................................................................... 155
Glasgow fuse-switch-disconnectors & switch-disconnectors.................................................................................................... 155
Glasgow busbar chamber system.............................................................................................................................................. 157
Exel 2 switch-disconnectors & switch-disconnector fuses......................................................................................................... 159
Exel distribution fuseboards....................................................................................................................................................... 160
HRC cartridge fuselinks, carriers and bases............................................................................................................................... 161
Rotary isolators........................................................................................................................................................................... 163
ADS8 AND AUTOLINE AC CONTACTORS, STARTERS AND ASSEMBLIES........................................................................... 165
PUSHBUTTON CONTROL UNITS MSU................................................................................................................................ 179
10.4 POWER FACTOR CORRECTION CAPACITORS........................................................................................................................ 180
10.5 DEGREES OF PROTECTION IP.............................................................................................................................................. 184

10.1 Technical data
Memshield 3 type A SPN, type B TPN distribution boards
Distribution boards type A and type B, technical overview

Type A Type B
IP Rating IP3X IP4X

Enclosure body type Steel welded case end with cable glad plate Steel welded case end with cable glad plate
Paint specification RAL 7004 epoxy polyester RAL 7004 epoxy polyester
Conditional short circuit rating 15kA to BS EN 61439 25kA to BS EN 61439
Busbar short time withstand (Icw) 5kA 0.1s 10kA 0.5s / 17kA 0.25s
Cable Capacities
125A switch disconnector 50mm2 50mm2
100A RCCB (type A = 90A) 35mm2 50mm2
250A switch disconnector 120mm2 (+ M8 lugs)
160A 250A MCCB incomer 250A = 120mm2 (+ M8 lugs)
100A direct connection kit 35mm2
250A direct connection lugs 120mm2 (+ M8 lugs)
125A contactor incomer 50mm2
250A contactor incomer 120mm2 (+ M8 lugs)
Enclosure earth stud M6 M8
Incoming earth terminal 25mm2 125A = 25mm2, 250A = 70mm2
Incomming neutral terminal 90/100A = 35mm2, 125A = 50mm2 125A = 50mm2, 250A = 120mm2 (+ M8 lugs)
Outgoing earth terminal 25mm2 25mm2
Outgoing neutral terminal 25mm2 25mm2
Type 1/type 2 combined lightning/surge arrester, technical data

Electrical EM3SSK3T12 & EMSSK3T12L EM3SSK3T12P
Lightning protection system class III, IV I, II, III, IV

Responding time (rate of voltage rise 5 kV/s) L-N/ N-PE < 25 ns / < 100 ns < 25 ns
Voltage protection level Up L-N/L-PE / N-PE < 1.5kV 1.5 kV
Maximum continuous operating voltage UC L-N/N-PE 280 VAC/255 VAC 440 VAC / 260 VAC
Temporary overvoltage test value UT (5 s) L-N/L-PE 348 VAC/370 VAC
(200 ms) N-PE 1200 VAC 200 VAC (200 ms)
Rated frequency 50/60 Hz 50/60 Hz
Discharge current (8/20) s Imax/In 100 kA
Open circuit voltage Uoc 20 kV
Nominal discharge current (8/20) s In L-N/N-PE 3x25 kA/100 kA
Maximum discharge current Imax L-N/N-PE 3x50 kA/100 kA
Impulse current Iimp (10/350) s:
Peak current L-N/N-PE 3x12.5 kA/100 kA 100 kA
Charge Q 50 As 50 As
Specific energy 2500 kJ/ 2500 kJ/
Follow current interrupt rating Ifi N-PE 100 Ar.m.s
at 260 V L-(PE)N/N-PE 3kArms/100Arms
at 440 V L-(PE)N/N-PE 1,5kArms/
Short-circuit current strength at max. back-up fuse 25kArms
Maximum back-up fuse 160 AgL/gG 125 AgL
Maximum short-circuit current 50 kAr.m.s
Type 2 surge arrester technical data

Electrical EM3SSK1T2 EM3SSK3T2
Responding time (rate of voltage rise 5 kV/s) L-N/N-PE/L-PE < 25ns/< 100ns/< 100ns < 25ns/< 100ns/< 100ns
Maximum continuous operating voltage UC L-N/N-PE 335VAC/260VAC 280VAC/260VAC
Temporary overvoltage test value UT (5 s) L-N 415 VAC 350 VAC
(200 ms) N-PE 1200 VAC 1200 VAC
Rated frequency 50/60 Hz 50/60 Hz
Nominal discharge current In L-N/N-PE/L-PE 20 kA (8/20)s 20 kA (8/20)s
Voltage protection level Up at In L-N/N-PE/L-PE 1600V/1000V/1650V 1000V/1000V/1300V
Maximum discharge current Imax L-N/N-PE/L-PE 40 kA (8/20)s 40 kA (8/20)s
Technical data
Memshield 3 type A SPN, type B TPN distribution boards 10.1
Memshield 3 type A SPN Distribution Board, Memshield 3 type B TPN Distribution Board,
dimensional drawing dimensional drawing
10 326
10
130
130 100
100
M6 Keyhole
440 fixing
83
A
Cable
terminations
37.6
B A
161 254
M6 KEYHOLE FIXINGS
B
= = 180
or Cable Box
250
List No. A (mm) B (mm)
(if fitted)
EAM4, EBMXDC6 238 163

EAMMP65 238 163 270
EAM7, EBMXDC9 292 217
EAM10 346 271
List No. A (mm) B (mm) C (mm)
EAM13, EBMXDC15, EBMXDCG15 440 365 125A 250A Lugs
EAM9M/MB 440 365 incomer incomer incomer
EAM16, EBMXDC18 454 379 EBM41 429 245 144 150

EAM12M/MB 454 379 EBM61 482 298 144 150
EAMSL66M/MB 454 379 EBM81, EBMXDC30 564 380 173 179
EAMSL93M/MB 454 379 EBM121, EBM121D, EBMXDC45 724 540 227 233
EBM161 830 540 227 233
EBM122 861 677 334 76 340
EBM182 1021 837 334 76 340
EBM242 1180 996 334 76 340
250A high load boards1)
EBM22H 817 633 237 500
EBM62H 1020 836 296 559
EBM82H 1055 871 277 540
EBM122H 1180 996 296 559
EBM182H 1342 1158 298 561
EBM242H 1501 1317 298 561
1)
Cable box not required

10.1 Technical data
Split metered power and lighting board 200A TPN
Split metered power and lighting board

200A TPN, dimensional drawing
326
10
130
100
M6 Keyhole
440 fixing
83
B A
270
List No. A (mm) B (mm)
EBMSL642MPMB 1130 946

EBMSL862MPMB 1236 1052
EBMSL1082MPMB 1342 1158
EBMSL14102MPMB 1501 1317

Technical data
Memshield 3 type A SPN pan assemblies 10.1
List No. Dimensions (mm) Minimum

recommended
a b c d e f g h j enclosure size (mm)
EAMP4 190 105.5 107.7 48.8 180 160 96 70 77 238 (W) x 254 (L)
EAMP7 274 129.5 160.9 79 180 214 96 70 107 292 (W) x 254 (L)
EAMP10 328 164 214.1 127.5 180 266 96 70 127.5 346 (W) x 254 (L)
EAMP13 382 183.5 267.3 131.3 192 319 109 82 161 440 (W) x 260 (L)
EAMP16 435 226.5 320.5 141.5 198 372 105 79 171 495 (W) x 260 (L)

10.1 Technical data
Memshield 3 type B TPN pan assemblies
279
List No. Dimensions (mm) Minimum

recommended
a b c d e f enclosure size (mm)
EBMP41 333.6 303.3 107.5 35.7 21 440 (W) x 425 (L)

EBMP61 413.7 383.5 160.6 35.7 21 440 (W) x 478 (L)
EBMP81 511.5 481.2 213.7 53.2 21 440 (W) x 560 (L)
EBMP121 638.1 589.2 319.9 22.2 40 440 (W) x 720 (L)
EBMP122 750 710 319.9 16.7 336.5 40 440 (W) x 861 (L)
EBMP182 910 870 479.2 16.7 435 40 440 (W) x 1016 (L)
EBMP242 1070 1030 638.5 16.7 515 40 440 (W) x 1176 (L)

Technical data
Memshield 3, surge protection devices 10.1
Memshield 3, surge protection devices, dimensional drawings
EM3SSK1T2 EM3SSKT2/EM3SSKT12
List No. A (mm) B (mm) C (mm) D (mm)

List No. A (mm) B (mm) C (mm) D (mm)
EM3SSK1T2 254 238 163 161
EM3SSK3T2 254 238 163 161
EM3SSK3T12 254 238 163 161

10.1 Technical data
Memshield 3, meter pack assemblies
Memshield 3, Meter pack assemblies, dimensional drawings
EBMMPCD120
EBMMPCT250/EBMMPCT250M/EBMMPCT250MID
Memshield 3, contactor incomer, dimensional drawings
List No. A (mm) B (mm) C (mm) D (mm) E (mm) F (mm)
EBMCC1253 440 252 270 161 170 130

EBMCC2503 440 595 270 501 130 130

Technical data
Memshield 3, meter pack assemblies 10.1
Memshield 3, Meter pack assemblies, dimensional drawings (contd)
EBMMPSL250/EBMMPSL250M
EBMMPSL125/EBMMPSL125M

10.1 Technical data
18mm miniature circuit breakers (MCBs)
18mm miniature circuit breakers (MCBs), technical data Tripping characteristic type B, C & D
7200
Eatons range of 10/15kA high performance miniature circuit
3600 2
breakers (MCBs) are manufactured and tested to IEC EN 60898, 1
and IEC EN 60947-2, meeting the latest UK, European and 1200 1 conventional non-tripping current
international standards, with ratings from 1A to 63A as standard. 600
Int = 1.13 IN : t > 1 h
2 conventional tripping current

DIN rail mountable and suitable for use with both pin and 300 It = 1.45 IN : t < 1 h
comb type busbar systems, Eatons MCBs are suitable for use 120
3
2.55 IN : t = 160 s (IN < 32A)
t = 1-120 s (IN > 32A)
on 230/400 VAC systems and are calibrated for use at 40C. 3 4 Type B: 3 IN : t > 0.1 s
60 5 IN : t < 0.1 s
These devices suite with the other modular devices including 5
30 6 Type C: 5 IN : t > 0.1 s

RCBOs, RCCBs and isolators, for use within Eaton Memshield3 7 10 IN : t < 0.1 s
Distribution boards and a wide range of other applications. 10 8 Type D: 10 IN : t > 0.1 s
9 20 IN : t < 0.1 s
The Eaton MCBs are fitted with box clamp terminals suitable 5
t [sec]
for use with cables up to 25mm2, and have a unique box 2
clamp barrier to prevent incorrect cable insertion. 1
3
Eaton miniature circuit breakers are available with B, C and 0.5
D characteristic curve as standard. Type C MCBs are most 0.2

commonly used in commercial and general applications where 0.1 5 7 9
there are lighting or motor loads involving high switching 0.05
4 B6 C 8
D
surges that may cause unwanted operation of type B
devices. Type D devices are more commonly used on general 0.02
industrial applications with much higher inrush surges. 0.01

0.005
IEC/EN 60898 Instantaneous Typical Eaton 10/15A
Type Trip Current (x In) Application MCB type 0.002
B 3 to 5 General distribution EMBH 0.001
C 5 to 10 Commercial EMCH 0.0005

Light industrial 1 2 3 4 5 6 7 8 9 10 15 20 30 40 50
D 10 to 20 General EMDH
I/IN
Industrial
Type B: Suitable for general, domestic and commercial
installations having little or no switching surges.
Type C: Suitable for general use in commercial or industrial
applications where the greater use of fluorescent lighting
and small motors can produce switching surges, which
may cause nuisance tripping of type B breakers.
Type D: Suitable for general industrial applications where there are
a lot of high inrush switching surges associated with equipment
such as transformers, large motors , welding and X ray equipment.
Earth fault loop impedances (Zs) to provide compliance

with BS 7671
The wiring regulations BS 7671 makes specific reference
to MCB types and the maximum earth loop impedance
allowable to meet the required disconnection times.
It can be seen that it is much easier to achieve
adequate disconnection times with type B devices
than it is with types C and indeed type D devices.
Maximum earth fault loop impedance i.e. Zs ohms for final circuits
fed from miniature circuit breakers MCBs or RCBOs with Uo of
230V, for instantaneous operation giving compliance with 0.4s
disconnection time of Reg 411.3.2.2 and 5s disconnection time
of 411.3.2.3
Note: A minimum Voltage factor Cmin = 0.95 has been introduced

to take account of variations in supply voltage depending on
time, place and transformer settings etc., in accordance with
Electricity Safety, Quality and Continuity regulations 2002.
The effect of this is to reduce the previous BS7671
maximum earth loop impedance Zs values by 5%.

Technical data
18mm miniature circuit breakers (MCBs) 10.1
10/15kA MCBs dimensional drawings MCB Max Zs (Ohms) figures (Data in line with BS7671)
Range In (A) Disconnection 0.4s Disconnection 5s
Type B (EMBH Series) 1 43.70 43.70

2 21.85 21.85
4 10.93 10.93
6 7.28 7.28
8 5.46 5.46
10 4.37 4.37
13 3.36 3.36
16 2.73 2.73
20 2.19 2.19
1-pole 2-pole (2P), 3-pole (3P) 4-pole (4P) 25 1.75 1.75
(1P) 1-pole+N (1P+N)
32 1.37 1.37
40 1.09 1.09
50 0.87 0.87
63 0.69 0.69
Type C (EMCH Series) 1 21.85 21.85
2 10.93 10.93
4 5.46 5.46
6 3.64 3.64
8 2.73 2.73
10 2.19 2.19
13 1.68 1.68
16 1.37 1.37
20 1.09 1.09
25 0.87 0.87
32 0.68 0.68
40 0.55 0.55
10/15kA MCBs technical data 50 0.44 0.44
63 0.35 0.35
Product standard IEC EN 60898 & IEC EN 60947-2 Type D (EMDH Series) 1 10.93 21.85
No of poles 1p, 1p&N, 2p, 3p, 4p 2 5.46 10.93
Mechanical specification 4 2.73 5.46
Device width (pole) 17.7mm 6 1.82 3.64
Terminal type Box clamp 8 1.37 2.73
Terminal capacity 125mm2 10 1.09 2.19
Terminal Screw M5 combination 13 0.84 1.68
Terminal torque 2.0Nm 2.4Nm max 16 0.68 1.37
Mounting DIN rail 20 0.55 1.09
Degree of protection IP 20 25 0.44 0.87
Positive contact indication Red/Green flag indicator 32 0.34 0.68
Electrical specification 40 0.27 0.55
Rated voltage 230/240 V AC 50 0.22 0.44
48V DC (per pole) 63 0.17 0.35
Current ratings 1, 2, 4, 6, 10, 13, 16, 20,
25, 32, 40, 50, 63 A Note : Values take account of minimum voltage factor Cmin - in accordance with
Rated impulse and withstand voltage 4kV (1.2/50) u sec BS7671 Amendment 3
Rated short circuit capacity 10kA to IEC EN 60898 and
15kA to IEC EN 60947-2
Selectivity class 3 to EN 60898
Tripping characteristic
Instantaneous tripping current I mt Type B: 3 In < Imt < 5 In
Type C: 5 In < Imt < 10 In
Type D: 10In < Imt < 20 In
Conventional non tripping current I nt = 1.13 In
Conventional tripping current It = 1.45 In
Ref/Calibration temp 40o C
Number of operating cycles elec >4000
Number of operating cycles mech >20000

10.1 Technical data
27mm style miniature circuit breakers (for 250A distribution boards)
27mm style miniature circuit breakers Tripping characteristic type B, C & D

(for 250A distribution boards)
7200
Eatons 27mm style miniature circuit breakers (MCBs) are
3600 2
manufactured and tested to IEC EN 60947-2, meeting the 1
latest UK, European and international standards, with ratings 1200 1 conventional non-tripping current
Int = 1.13 IN : t > 1 h
from 20A to 125A single and triple pole as standard. 600
2 conventional tripping current
Eatons MCBs are suitable for use on 230/400 VAC systems and 300 I t = 1.45 IN : t < 1 h
2.55 IN: t = 1- 60 s (IN < 32A)

are calibrated for use at 40C. and are available with B, C, and 120
3
t = 1-120 s (IN > 32A)
D characteristic curve, with breaking capacities up to 25kA. 3 4 Type B: 3 IN : t > 0.1 s
60 5 5 IN : t < 0.1 s
30 6 Type C: 5 IN : t > 0.1 s

7 10 IN : t < 0.1 s
15/25kA MCBs technical data 10 8 Type D:10 IN : t > 0.1 s

9 20 IN : t < 0.1 s
5
t [sec]
Product standard IEC EN 60947-2 2
No of poles 1p, 3p 1
3
Mechanical specification 0.5
Device width (pole) 27mm 0.2

Terminal type Lower Box clamp Upper Box clamp 5 7 9
0.1
Terminal capacity 1 - 25 mm2 2 - 16 mm2 0.05
4 B6 C 8
D
Terminal Screw MS Combination MS Combination 0.02
Terminal torque 2.4Nm max 1.5Nm max 0.01
Mounting DIN rail 0.005
Degree of protection IP 20 0.002

Positive contact indication Red/Green flag indicator 0.001
Electrical specification 0.0005
Rated voltage 230/400 V AC 1 2 3 4 5 6 7 8 9 10 15 20 30 40 50

60V DC (per pole) I/IN
Current ratings 63, 80, 100, 125 A
Rated impulse and withstand voltage 4kV (1.2/50) u sec
Eaton Memshield-3 MCB Max Zs (Ohms)
Types B and C 2063A 25kA Data in line with BS7671
80100A 20kA
Range In (A) Disconnection 0.4s Disconnection 5s
125A 15kA
Type B (EMBS Series) 20 2.19 2.19
32 1.37 1.37
Type D 2063A 25kA
40 1.09 1.09
80A 20kA
50 0.87 0.87
100A 15kA
63 0.69 0.69
Selectivity class In accordance with class C
80 0.55 0.55
100 0.44 0.44
Instantaneous Tripping current I mt Type B: 3 In < Imt < 5 In
Type C: 5 In < Imt < 10 In 125 0.35 0.35
Type D: 10In < Imt < 20 In Type C (EMCS Series) 20 1.09 1.09
Conventional non tripping current I nt = 1.13 In 32 0.68 0.68
Conventional tripping current It = 1.45 In 40 0.55 0.55
Ref/Calibration temp 40o C 50 0.44 0.44
Number of operating cycles elec >20000 63 0.35 0.35
80 0.27 0.27
100 0.22 0.22
Miniature circuit breakers dimensional drawings
125 0.17 0.17
Type D (EMDS Series) 20 0.55 1.09
32 0.34 0.68
40 0.27 0.55
50 0.22 0.44
63 0.17 0.35
80 0.14 0.27
100 0.11 0.22
Note : Values take account of minimum voltage factor Cmin - in accordance with
BS7671 Amendment 3

Technical data
Residual current circuit breakers (RCCBs) 10.1
Residual current circuit breakers (RCCBs) technical data RCCB dimensions (mm)
PFIM PFIM
Eatons range of residual current circuit breakers without integral
Overload protection (RCCBs), are manufactured2Pto IEC EN/61008 4P2P 2P 5,5 30,5 4P 4,5 5,5 30,5 4,5
and meet the latest European and International standards.

DIN rail mountable in 2 and 4 module widths these RCCBs
provide protection solutions to a wide range of applications. T
With standard thermal ratings of 16A to 100A and trip 80 80
80 45 80
sensitivities of 10mA, 30mA, 100mA and 300mA, these devices
can be equipped with a range of modular accessories.
The Eaton RCCBs suite with the complete range of modular 10,5
devices, and are for use within Eatons Memshield3

35 70 35 44
70 44
distribution boards and other applications. 60 60
These devices will accommodate cables up to 35mm . 2
4P
Terminology
RCD Residual current device:- This is the generic term covering a
range of devices that are able to detect residual currents sometimes
also referred to as earth leakage current. The residual current is
measured by detecting the difference between the current flowing
in the live and neutral conductors of a circuit and where the residual
current is above a predefined level the RCD will trip. RCDs are
available in a range of trip sensitivities for different applications.
RCCB Residual current circuit breaker is an RCD which
will cause disconnection of the electrical supply should it
detect a residual current passing through the device, above a
specified tripping current limit e.g. 30mA. This device does not
provide over current protection and is therefore also referred
to as an RCCB without integral over-current protection.
RCBO Residual current circuit breaker, with overload protection,
is an RCCB which will cause disconnection of the electrical supply
should it detect a residual current above a specified tripping
current limit, combined with integral overload, over-current, and RCCB technical data
shortcircuit protection associated with a miniature circuit breaker. Specifications 2-pole RCCB 4-pole RCCB
The 17th Edition of the IEE wiring regulations BS7671 now places Product standard IEC EN 61008 IEC EN 61008
much greater emphasis on the use of 30mA RCDs to provide No of poles 2p 4p
additional protection in many areas covered by the regulations, Mechanical specification
such as circuits feeding socket outlets and for Device width 35 mm 70 mm
the protection of concealed wiring.
Terminal type Box clamp Box clamp
Terminal capacity 1.535mm2 35mm2
Trip sensitivities
Terminal Screw M5 combination M5 combination
10mA Provides the highest degree of RCD protection in Terminal torque 2.4Nm max 2.4Nm max
hazardous environments where supplementary protection against
Mounting DIN rail DIN rail
electric shock is required. This very high sensitivity should only
be applied to final circuits where a high degree of risk exists. Degree of protection IP 20 IP 20
Positive contact indication Yes (toggle position) Red/green flag
30mA Provides a high degree of protection against electric
Electrical specification
shock due to direct and indirect contact. A 30mA RCD will trip
within 40mS when a fault current of 150mA is detected. Rated voltage 230/400 V AC 230/400 V AC
Current ratings 16, 40, 63, 80,100 A 16, 40, 63, 80,100 A
This type of RCD is required to satisfy the requirements for
additional protection in accordance with BS7671 (IEE wiring regs.) Rated impulse 4kV (1.2/50) u sec 4kV (1.2/50) u sec
and withstand voltage
100mA Provides a degree of protection against Rated short circuit capacity 10kA (with back up) 10kA (with back up)
electric shock resulting from indirect contact, and is Sensitivity AC AC
generally used to protect a group of circuits as well
as providing overall protection against Fire risk.
Rated tripping currents 10, 30, 100, 300 mA 10, 30, 100, 300 mA
300mA Provides a lower level of RCD protection in
Tripping type Instantaneous Instantaneous
the form of an overall protection against the risk of
Number of >4000 >4000
fire resulting from faults in electrical wiring etc.
operating cycles elec
Number of >20000 >20000
operating cycles mech

10.1 Technical data
Residual current circuit breakers with overload (RCBOs)
Residual current circuit breakers with overload protection (RCBOs) technical data
Eatons range of residual current circuit breakers with integral overload protection (RCBOs), are
manufactured to IEC EN 61009 and meet the latest European and International standards.
Trip Sensitivity
Provides a high degree of protection against electric shock due to direct contact. A 30mA
RCD will trip within 40mS when a fault current of 150mA is detected.
This type of RCD is required to satisfy the requirements for additional protection in accordance with BS7671 (IET wiring regs.)
Single phase RCBO technical data RCBOs dimensions (mm)

Specifications PKS6
Product standard IEC EN 61009

No of poles 1p & solid N
Mechanical specification
Device width 17.7 mm
Terminal type Lower-Box clamp Upper-Box clamp
Terminal capacity 125mm2 2-16mm2
Terminal Screw M5 combination M4 combination 102
102
Terminal torque 2.4Nm max 1.5Nm max
Mounting DIN rail
Degree of protection IP 20
Positive contact indication Yes (Red/Green flag)
Electrical specification
Rated voltage 230/240 V AC
Current ratings
6, 10, 16, 20, 25, 32, 40, 45A
Rated impulse and withstand voltage 4kV (1.2/50) u sec
Rated short circuit capacity 10kA
Sensitivity Type A
Instantaneous Tripping current I mt Type B: 3 In < Imt < 5 In
Type C: 5 In < Imt < 10 In
Conventional non tripping current I nt = 1.13 In
Conventional tripping current It = 1.45 In
Ref/Calibration temp 40o C
Rated tripping currents 10, 30, 100mA
Tripping type Instantaneous
Number of operating cycles elec >400
Number of operating cycles mech >20000
Three phase RCBO technical data

Electrical
Design according to IEC/EN 61009
Tripping
line voltage-independent instantaneous 250A (8/20s)
surge current-proof
Rated voltage Ue 240/415V; 50Hz
Rated tripping current In 0, 100, 300 mA
Rated non-tripping current Ino 0.5 In
Sensitivity Type A (AC and pulsating DC)
Selectivity class 3 Mechanical
Rated breaking capacity 10 kA Frame size 45 mm
Rated current 6 - 32 A Device height 80 mm
Rated peak withstand voltage Uimp 4 kV (1.2/50s) Device width 70 mm
Characteristic B, C, D Upper and lower terminals open mouthed/lift terminals
Maximum back-up fuse (short circuit) 100 A gL (>10 kA) Terminal capacity 1 - 25 mm2
Endurance electrical comp. 4,000 operating cycles Degree of protection IP20
mechanical comp. Operating temperature -25C to +40C
20,000 operating cycles Resistance to climatic conditions acc. to IEC/EN 61009

Technical data
Control and switching devices dimensions and data 10.1
Analogue time switches
TSSD1CO TSSD1NO TSQW1CO TSQD1CO TSQD1NO
General
Operating voltage 230V AC 230 V AC 110 - 230 V AC 110 - 230 V AC 230 - 240 V AC
Frequency 50 Hz 50 Hz 50 - 60 Hz 50 - 60 Hz 50 - 60 Hz
Stand-by power 0.5 W 0.5 W 0.5 W 0.5 W 0.5 W
Time control Net Net Quartz Quartz Quartz
Accuracy acc. Net acc. Net 1 sec. / day 1 sec. / day 1 sec. / day
Power reserve - - 200 hrs / 200 hrs/
/ 100 hrs at 110 V 100 hrs at 110 V 3 days
Battery type - - NiMH NiMH NiMH
Degree of protection (EN 60529) IP20 IP20 IP20 IP20 IP20
Ambient temperature -20 C...+55 C -20 C...+50 C -20 C...+55 C -20 C...+55 C -10 C...+50 C
Protection class (EN 60730-1) II II II II II
Switching contact(s)
Type of switching contact 1 x CO 1 x NO 1 x CO 1 x CO 1 x NO
Switching capacity at 250 V~, cos = 1 16 A 16 A 16 A 16 A 16 A
Switching capacity at 250 V~, cos = 0,6 4A 4A 4A 4A 4A
Programming features
Period of program Day Day Week Day Day
Number of channels 1 1 1 1 1
Minimum cycle time 15 min. 15 min. 2 hrs 15 min. 15 min.
Programmable every 15 min. every 15 min. every 2 hrs every15 min. every 15 min.
Program steps 96 96 84 96 96
Manual / Hand / Permanent switching 1) On, Off, Auto On, Off, Auto On, Off, Auto On, Off, Auto On, Off, Auto
Switching status indication x x x x x
Dimensions and weight
Number of module width 3 1 3 3 1
Dimensions Width 52.5 mm 17.5 mm 52.5 mm 52.5 mm 17.5 mm
Height 90 mm 90 mm 90 mm 90 mm 90 mm
Depth 65.5 mm 65.5 mm 65.5 mm 65.5 mm 65.5 mm
Mounting DIN-rail DIN-rail DIN-rail DIN-rail DIN-rail
Terminals
Terminal screw size M3.5 M3.5 M3.5 M3.5 M3.5
1
) Remark
ON = Permanent ON
OFF = Permanant OFF
Hands = ON or OFF. valid until next program cycle overrules
Auto = According program

10.1 Technical data
Control and switching devices dimensions and data
Technical data
7
Analogue dailyand
Analogue daily andweekly
weekly timers,
timers, dimensional
dimensional drawings
drawings
. .
.
7
.
.
Analogue
Analoguedaily
dailyand
andweekly
weeklytime switches,
time wiring
switches, diagrams
wiring diagrams
CA081003EN - January 2013 TECHNICAL DATA 13

Technical data
Digital timers - week programme
TSDW1CO TSDW1COMIN TSDW2CO TSDW1COA TSDW1CODG
General
Nominal operating voltage 220 - 240 V AC 240 V AC 220 - 240 V AC 230 - 240 V AC 230 - 240 V AC
Frequency 50 - 60 Hz 50 - 60 Hz 50 - 60 Hz 50 - 60 Hz 50 - 60 Hz
Stand-by power 0,8 W 0,4 W 0,8 W 0,8 W 1,4 W
Time base control 1) Quartz Quartz Quartz Astro Quartz or DCF / GPS
Accuracy 0,5 sec. / day 0,5 sec. / day 0,5 sec. / day 0,5 sec. / day 0,5 sec. / day
Power reserve 10 year 10 year 10 year 10 year 10 year
Type of battery Lithium Lithium (exchangeable) Lithium Lithium Lithium
Protection class (acc. EN 60529) IP20 IP20 IP20 IP20 IP20
Permissible ambient temperature -30 C...+55 C -25 C...+55 C -30 C...+55 C -30 C...+55 C -30 C...+55 C
Protection class at proper installation (acc. EN 60730-1) II II II II II
Type of switching contact 1 x CO 1 x CO 2 x CO 1 x CO 1 x CO
Switching capacity at 250 V~, cos = 1 16 A 16 A 16 A 16 A 16 A
Switching capacity bij 250 V~, cos = 0,6 10 A 6A 10 A 10 A 10 A
Switching capacity for lighting
- Incandescent lamp 2600 W 1000 W 2600 W 2600 W 2600 W
- Halogen lamp 2600 W 1000 W 2600 W 2600 W 2600 W
Period of programme Week Week Week Week Week
Number of channels 1 1 2 1 1
Minimum switching capacity 10 mA - 10 mA 10 mA -
Minimum cycle time 1 min. 1 min. 1 min. 1 min. 1 sec.
Maximum programming steps in memory 56 56 56 56 84
Summer / wintertime automatic (or manual on/off) Yes Yes Yes Yes Yes
Random programme No No No No Yes (2)
Holiday programme Yes Yes Yes Yes Yes
Cycle programme No No No No Yes
Astro function No No No Yes No
Pulse switching No No No No Yes
Manual switching 2) On, Off, Auto On, Off, Auto On, Off, Auto On, Off, Auto On, Off, Auto
LCD backlighting Yes - Yes Yes Yes
PIN code Yes Yes Yes Yes Yes
Number of module width 2 1 2 2 2
Dimensions Width 35.8 mm 17.5 mm 35.8 mm 35.8 mm 35.8 mm
Height 90.1 mm 90 mm 90.1 mm 90.1 mm 90.1 mm
Depth 69.2 mm 65.5 mm 69.2 mm 69.2 mm 69.2 mm
Mounting DIN-rail DIN-rail DIN-rail DIN-rail DIN-rail
Terminals
Terminal type Spring Screw Spring Spring Spring
1) Remark: ) Remark:
2
Astro function: Automatic calculation of sunrise and sunset times ON = Permanent ON

DCF / GPS: Time synchronization is possible by connecting external antenna (TSADCF of TSAGPSKIT). OFF = Permanent OFF
Auto = According Programme

10.1 Technical data
Technical data
7
Digital weekly time switches, dimensional drawings
drawings
. .
. . .
. . .
7
.
.
.
. .
. . . .
. . . . . .
. .
. .
Digital weekly timers, wiring diagrams

diagrams
142 POWER DISTRIBUTION COMPONENTS PG01414001U March 2015 CA081003EN - January 2013 TECHNICAL DATA 15
Technical data
Twilight switches and combination with timer
SRSD1NO SRSD1COW SRCD1CO SRSW1NO
General
Nominal operating voltage 220 - 240 V AC 220 - 240 V AC 220 - 240 V AC 220 - 230 V AC
Frequency 50 - 60 Hz 50 - 60 Hz 50 - 60 Hz 50 - 60 Hz
Stand-by power 0,8 W 1,1 W 1,3 W 0,6 W
Photosensitivity 2 - 100 lux 2 - 2000 lux 2 - 2.000 lux 2 - 2.000 lux
Maximum cable length for sensor 25 mtr. 100 mtr. 100 mtr. -
Maximum cable length for sensor -25 C...+50 C -30 C...+55 C -30 C...+55 C -35 C...+55 C
Protection class at proper installation - modular device II II II II
Type of switching contact 1 x NO 1 x CO 1 x CO 1 x NO
Contact type Floating Floating Floating (not for SELV) Floating 230 V
Switching capacity at 250 V~, cos = 1 16 A 16 A 16 A 16 A
Switching capacity at 250 V~, cos = 0,3 - - 10 A 10 A
Maximum lamp load:
- Incandescent lamp 2300 W 2300 W 2600 W 2300 W
- Energy saving lamp 9 x 7 W, 7 x 11 W, 9 x 7 W, 7 x 11 W, 22 x 7 W, 18 x 11 W, 9 x 7 W, 7 x 11 W,
7x 15 W, 7 x 20W, 7x 15 W, 7 x 20W 16 x 15 W, 16 x 20 W, 7 x 15 W, 7 x 20 W,
7 x 23 W 7 x 23 W 14 x 23 W 7 x 23 W
- Fluorescent lamp load - single fitting 2300 VA 2300 VA 2300 VA 2300VA
uncompensated (inductive)
Switching delay off 20 sec. 0 - 20 min. 0 - 59 min. 2 - 100 sec.
Switching status indication (not delayed) Yes Yes - Yes
Period of programme - - Week -
Number of channels - - 1 -
Programming using software and memory - - Yes -
Summer / wintertime automatic (or manual on/off) - - Yes -
Random programme - - No -
Holiday programme - - Yes -
Cycle programme - - No -
LCD backlighting - - Yes -
Number of module width 1 2 3 -
Dimensions Width 17.5 mm 54 mm 72 mm 85 mm
Height 85.5 mm 86 mm 86 mm 118.4 mm
Depth 65.5 mm 65.5 mm 65.5 mm 49.4 mm
Terminals
Terminal type Screw Spring Spring (duo fix) -

10.1 Technical data
Technical data
7
Twilight switches
Twilight and
switches combinations
and with
combinations timer,
with dimensional
timer, drawings
dimensional drawings
. .
.
7
. .
.
.
Twilight switches
Twilight and
switches combinations
and with
combinations timer,
with wiring
timer, diagrams
wiring diagrams

CA081003EN - January 2013 TECHNICAL DATA 17
Technical data
Contactors type CR
Products Contactors Aux. contact
Rating 20 A 25 A 40 A 63 A 6A
General
Standards IEC 60947-4-1, IEC 61095 IEC 60947-5-1
Nominal operating voltage 1-phase Ue 1-ph. 230 V 230 V 230 V 230 V 230 V
Nominal operating voltage 3-phase Ue 3-ph. 400 V 400 V 400 V - -
Overvoltage protection on coil 430 V (*5) 430 V (*5) 430 V 430 V
Mechanical endurance (switching cycles) 3.000.000 3.000.000 3.000.000 3.000.000 3.000.000
Protection class (acc. DIN 40 050, IEC 529) IP20 IP20 IP20 IP20 IP20
Permissible ambient temperature -5+55 C -5+55 C -5+55 C -5+40 C -5+55 C
Storage temperature -30+80 C -30+80 C -30+80 C -30..+80 C -30+80 C
Contact rating
Rated insulation voltage Ui 440 V 440 V 500 V 500 V 500 V
Frequency 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz
Rated impulse withstand voltage Uimp 4 kV 4 kV 4 kV 4 kV 4 kV
Rated thermal current Ith 20 A 25 A 40 A 63 A 6A
AC1/AC7a Rated operational current Ie 20 A 25 A 40 A 63 A
AC1/AC7a Operational power rating at Ue = 230 Vac Pmax 4 kW 9 kW 16 kW 24 kW
AC1/AC7a Operational power rating at Ue = 400 Vac Pmax 16 kW 26 kW 40 kW
AC3/AC7b Operational power rating at Ue = 230 Vac Pmax 1,3 kW (*1) 2,2 kW 5,5 kW 8,5 kW
AC3/AC7b Operational power rating at Ue = 400 Vac Pmax 4 kW 11 kW 15 kW -
DC1 Rated thermal current at Ue = 24 Vdc Ie 20 A 25 A 40 A 63 A
DC1 Rated thermal current at Ue = 110 Vdc Ie 1A 2A 4A 4A
DC1 Rated thermal current at Ue = 220 Vdc Ie 0,5 A 0,5 A 0,8 A 0,8 A
DC1 Rated thermal current at Ue = 24 Vdc
(2-poles in series) Ie 20 A 25 A 40 A 63 A
(2-poles in series) Ie 3 A 4 A 10 A 10 A
(2-poles in series) Ie 1,5 A 1,5 A 6 A 6 A
(3-poles in series) 25 A 40 A 63 A
DC1 Rated thermal current at Ue =110 Vdc
(3-poles in series) 6:00 AM 30 A 35 A
(3-poles in series) 2,5 A 20 A 30 A
Electrical endurance
Maximum operating cycles at AC1/AC7a application 200.000 x 200.000 x 100.000 x 100.000 x
Maximum operating cycles at AC3/AC7b application 300.000 x 500.000 x 150.000 x 150.000 x
Maximum operating cycles at AC5a application 100.000 x 100.000 x 100.000 x 100.000 x
Maximum operating cycles at AC5b application 100.000 x (*2) 100.000 x (*2) 100.000 x (*3) 100.000 x (*4)
Maximum operating cycles per hour 600 x 600 x 600 x 600 x 600 x
Power dissipation per contact at In 1,7 W 2,2 W 4 W 8 W
Maximum back-up fuse 25 A gL 35 A gL 63 A gL 80 A gL
Rating 20 A 25 A 40 A 63 A 6A
Operating coil (for combined ac/dc types only CR)
Coil inrush power (for all voltage ratings) 2,5 W 3 W 5 W 5 W
Coil consumption (for all voltage ratings) 2,5 W 3 W 5 W 5 W
Closing delay 15-25 ms 15-30 ms 15-20 ms 15-20 ms
Opening delay 35-45 ms 50-80 ms 35-45 ms 35-45 ms
Operating coil (for ac types only CRA)
Coil inrush power (for all voltage ratings) 13 W/15 VA 17 W/27 VA
Coil consumption (for all voltage ratings) 2 W/5 VA 1 W/2.7 VA
Closing delay 15 ms 15-25 ms
Opening delay 10 ms 35-45 ms

10.1 Technical data
Contactors type CR (continued)

Products Contactors Aux. contact
Dimensions
Width 18 mm 35 mm 54 mm 54 mm 9 mm
Height 85 mm 85 mm 85 mm 85 mm 85 mm
Depth 60 mm 60 mm 60 mm 60 mm 60 mm
Terminals for main & auxiliairy contacts
Terminal capacity fine stranded wire 16 mm2 16 mm2 116 mm2 116 mm2 12,5 mm2
Terminal capacity solid wire 110 mm2 110 mm2 125 mm2 125 mm2 12,5 mm2
Terminal screw size M3,5 M3,5 M5 M5 M3
Terminal screw head type (Pozidrive) PZ Size 1 PZ Size 1 PZ Size 2 PZ Size 2 PZ Size 1
Maximum torque 1,2 Nm 1,2 Nm 2,0 Nm 2,0 Nm 0,8 Nm
Terminals for operating coils
Terminal capacity fine stranded wire 12,5 mm2 12,5 mm2 12,5 mm2 12,5 mm2
Terminal capacity solid wire 12,5 mm2 12,5 mm2 12,5 mm2 12,5 mm2
Terminal screw size M3 M3 M3 M3
Terminal screw head type (Pozidrive) PZ Size 1 PZ Size 1 PZ Size 1 PZ Size 1
Maximum torque 0,6 Nm 0,6 Nm 0,6 Nm 0,6 Nm
Remarks:
*1) Only applicable for normally open contact(s)
*2) At 1,5 kW
*3) At 3 kW
*4) At 5 kW
*5) For CR types only (combined ac/dc types), NOT for CR A types
Contactors, type CR20, CR25 Contactors, type CR40, CR63
Day/night contactors, type CRM20, CRM25 Auxiliairy contact

Technical data
Earth leakage relays and CTs 10.1
Earth leakage relays and CTs, dimensional drawings
PFR-W-20 PFR-W-30 PFR-W-30
Type A B C D E
PFR-W-35 100 79 26 48.5 35

PFR-W-70 130 110 32 66 70
PFR-W-105 170 146 38 94 105
PFR-W-140 220 196 48.5 123 140
PFR-W-210 299 284 69 161 210

10.2 Technical data
NZM MCCBs, maximum Zs (Ohms) figures to achieve disconnection at 0.4s and 5s
MCCB type Rating (A) Disconnection 0.4s Disconnection 5s

Minimum setting Maximum setting Minimum setting Maximum setting
NZM1 range 16 - 1.366 - 1.485

20 1.821 1.093 1.496 1.188
32 1.138 0.683 0.936 0.742
40 0.910 0.546 0.749 0.594
50 0.729 0.437 0.599 0.475
63 0.578 0.347 0.475 0.377
80 0.455 0.274 0.374 0.297
100 0.364 0.219 0.299 0.238
125 0.292 0.175 0.239 0.190
160 0.228 0.137 0.187 0.148
NZM2 range 125 0.292 0.175 0.239 0.190
160 0.228 0.137 0.187 0.148
200 0.182 0.109 0.150 0.119
250 0.145 0.087 0.120 0.095
NZM3 range 250 0.145 0.087 0.120 0.095
320 0.114 0.068 0.093 0.074
400 0.091 0.055 0.075 0.060
NZMLW range 630 0.174 0.044 0.174 0.044
800 0.137 0.034 0.137 0.034
Note : Values take account of minimum voltage factor Cmin - in accordance with BS7671 Amendment 3

Technical data
Panelboard dimensional drawings 10.2
Panelboard dimensional drawings
Panelboards Side extension boxes Extension boxes

10.2 Technical data
Panelboard dimensional drawings
Panelboard dimensions
Description Eaton list Dimensions (mm)
number A B C D E F G
Extension boxes EPBN1EX250 705 525 185.5 90

EPBN2EX250 855 525 210.5 165
EPBN3EX250 980 625 210.5 177.5
Filler boxes EPBN1CX250 185.5
EPBN2CX250 210.5
Panelboards EPBN1425 830 544 703 185.5 525 143 89
EPBN1625 920 544 703 185.5 525 188 89
EPBN1825 1010.5 837.5 703 185.5 525 86.5 89
EPBN11225 1191.5 1002 703 185.5 525 94.75 89
EPBN1640 1291.5 956.5 853 210.5 525 167.5 164
EPBN11240 1563 1228 853 210.5 525 167.5 164
EPBN2640 1291.5 956.5 853 210.5 525 167.5 164
EPBN21240 1563 1228 853 210.5 525 167.5 164
EPBN21840 1834.5 1499.5 853 210.5 525 167.5 164
EPBN2863 1650 1315 978 210.5 625 167.5 176.5
EPBN21263 1650 1315 978 210.5 625 167.5 176.5
EPBN21863 1915.5 1580.5 978 210.5 625 167.5 176.5
EPBN3880 1650 1315 978 210.5 625 167.5 176.5
EPBN31280 1915.5 1580.5 978 210.5 625 167.5 176.5
Side cable box EPBN1425SXB 830 544 143 185.5
EPBN1525SXB 920 544 188 185.5
EPBN1825SXB 1010.5 837.5 86.5 185.5
EPBN11225SXB 1191.5 1002 94.75 185.5
EPBN2640SXB 1291.5 856.5 167.5 210.5
EPBN21240SXB 1563 1228 167.5 210.5
EPBN21840SXB 1834.5 1499.5 167.5 210.5
EPBN21263SXB 1650 1315 167.5 210.5
EPBN21863SXB 1915.5 1580.5 167.5 210.5
Meter packs EPBN1EX250M 705 525 185.5 90
EPBN2EX250M 855 525 210.5 165
EPBN3EX250M 980 625 210.5 177.5
Side meter box EPBN1425SXM 830 544 143 185.5
EPBN1525SXM 920 544 188 185.5
EPBN1825SXM 1010.5 837.5 86.5 185.5
EPBN11225SXM 1191.5 1002 94.75 185.5
EPBN2640SXM 1291.5 856.5 167.5 210.5
EPBN21240SXM 1563 1228 167.5 210.5
EPBN21840SXM 1834.5 1499.5 167.5 210.5
EPBN21263SXM 1650 1315 167.5 210.5
EPBN21863SXM 1915.5 1580.5 167.5 210.5
Din enclosures EPBN1EXDIN 705 525 185.5 90
EPBN2EXDIN 855 525 210.5 165
EPBN3EXDIN 980 625 210.5 177.5
Surge suppression box EPBN1SPD123 185.5
EPBN1SPD1234 210.5

Technical data
Panelboard dimensional drawings 10.2
Rating (A) Panelboard/incomer connection kit combination Dimensions A (mm)
250 EPBN1425 EPBKN1253 210

EPBN1625 EPBKN1253M
EPBN1825 EPBKN1254
EPBN11225 EPBKN1254M
EPBN1425 398
EPBN1625 EPBKN125L
EPBN1825 EPBKN125LM
EPBN11225
400 EPBN1640 EPBKN2403 380
EPBN2640 EPBKN2404
EPBN21840
EPBN1640 731
EPBN11240 EPBKN240L
EPBN2640 EPBKN240LM
EPBN21240
EPBN21840
630 EPBN2863 EPBKN2633 705
EPBN21863 EPBKN2634
EPBKN2634M
EPBN2863 EPBKN263L 775
EPBN21263 EPBKN263LM
EPBN21863
800 EPBN3880 EPBKN3803 454
EPBKN3804
EPBKN3804M

10.2 Technical data
Panelboard multifunction meter, technical characteristics and specification
3 phase 3 or 4 wire system. Meter is self-powered from voltage supply.

Liquid crystal display with backlight. 4 lines, 4 digits per line to Auxiliary voltage supply not required.
show electrical parameters. 5th line, 8 digits to show energy. Front panel indicator when Pulse Output or Comms operates.
Bar graph for current indication as percentage of CT rating. The range of meter is a class 1 multi-function, panel
96 x 96mm panel mount, 55mm rear panel. mounting meter to measure electrical parameters on LV
Modbus comms & pulse output. supplies to The meter is a Class 1 multi-function, panel
mounting meter to measure electrical parameters on
Fast installation plug-ib cabling for current and voltage LV supplies to and from TP&N distribution boards. It is
inputs. Feed-through voltage supply capability. ideal for applications such as:
Phase sequence detection and correction capability. Energy monitoring.
Multifunction meter measuring parameters: Power factor analysis.
Voltage (P-P / P/N) (individual/average) Supply capacity.
Current (I1, I2, I3) (individual/average) Building regs part L2.
Frequency Building performance.
Power factor (individual/average) Environmental standards e.g. IS14001, EMAS, ECA.
Active, reactive, apparent power (individual/total) Climate change levy.
Active, reactive, apparent energy (total) Carbon trading.
Display scrolling selectable for automatic or manual. Carbon footprints.
The six dedicated buttons are labelled as V, I, VAF, PF, P, E. The parameters available by pressing each key are detailed below:
Measurements available via:
Button 1 (V) Line to neutral voltage of three phase and average line to line voltage
Line to line voltage of three phase and average line to line voltage
Button 2 (I) Phase current of three phase and average phase current.
Phase current of three phase and maximum phase current.
Button 3 (VAF) Voltage, current, power factor of first phase and frequency
Voltage, current, power factor of second phase and frequency
Voltage, current, power factor of third phase and frequency
Average value of voltage, current, power factor of three phase and frequency
Button 4 (PF) Power factor of three phase and average power factor
Button 5 (P) Active power of three phase and total active power
Reactive power of three phase and total reactive power
Apparent power of three phase and total apparent power
Active, reactive, apparent power and power factor of first phase
Active, reactive, apparent power and power factor of second phase
Active, reactive, apparent power and power factor of third phase
Total active, reactive, apparent power and average power factor of three phase
Maximum active power demand, reactive power demand, apparent power demand
Minimum active power demand, reactive power demand
Button 6 (E) Active energy of three phase
Apparent energy of three phase
Reactive energy of three phase
Accuracy Accuracy
Measurement Accuracy Measurement Accuracy
Voltage VL-N 0.5% of full scale Power factor 0.01

Voltage VL-L 0.5% of full scale Active energy Class 1
Current 0.5% of full scale Apparent energy Class 1
Frequency 0.1% Reactive energy Class 1
For voltage >20V L-N MAX / MIN active power Class 1
For voltage >35V L-N
MAX / MIN reactive power Class 1
Active power Class 1
MAX apparent power Class 1
Apparent power Class 1
Reactive power Class 1

Technical data
MCCB pan assemblies, dimensions 10.2
250A pan assembly dimensions EPBPN1425EPBPN11225 400A pan assembly dimensions EPBPN1640EPBPN21840
Eaton list A B C D
number
EPBPN1425 29.5 483 592.5

181.5
Eaton list A B C D E F G H J
EPBPN1625 29.5 578.5
683 272 number
EPBPN1825 131 669 773.5
362.5 EPBPN1640 167 N/A 473.5 923 979.5 222.25 N/A N/A 318.25
EPBPN11225 131 850 954.5
543.5 EPBPN11240 167 438.5 725.5 1175 1231.8 358 N/A N/A 454
EPBPN2640 167 N/A 473.5 923 979.5 177 96.75 102 383
EPBPN21240 167 348 745 1194.5 1251 312.75 232.5 102 518.75
EPBPN21840 167 529 1016.5 1466 1522.5 448.25 368.25 102 654.5

10.2 Technical data
MCCB pan assemblies, dimensions
630800A pan assembly dimensions EPBPN2863, EPBPN21263, EPBPN21863, EPBPN3880, EPBPN31280
Eaton list A B C D E F G H J K
number
EPBPN2863 167 N/A 543.5 996 1052.5 1240 1291 177 96.75 601.5
EPBPN21263 167 N/A 724.5 1177 1233.5 1421 1472 267.5 187.25 692
EPBPN21863 167 438.5 996 1448.5 1505 1692 1743 403.25 323 828
EPBPN3880 167 N/A 580.5 1033 1089.5 1277 1328 177 96.75 638.5
EPBPN31280 167 N/A 761.5 1214 1270.5 1458 1509 222.25 142 794.5

Technical data
Enclosed switch & fusegear 10.3
Glasgow fuse-switch-disconnectors and switch-disconnectors dimensions
Nominal Poles Dimensions, mm
unit rating, In (A) A B C D E F H J R
63 SPSN, DP 289 199 180 283 203 127 7.9 43 36

TPN, TPSN 289 275 180 283 203 203 7.9 43 36
100 SPSN, DP 327 199 180 283 241 127 7.9 43 35
TPN, TPSN 327 275 180 283 241 203 7.9 43 35
160, 200 SPSN, DP 431 280 229 383 340 140 7 45 70
TPN, TPSN 431 340 229 383 340 200 7 45 70
315, 400 TPN, TPSN 501 467 291 545 385 375 10 58 46
500, 630, 800 TPN, TPSN 596 680 381 715 440 550 14 78 65
Units have retractable handles. D dimension indicates fully extended operating position.
Rating to BS EN 60947-3 general performance characteristics

Nominal unit rating, Ie (A) Utilisation category at Ue 415V to BS EN 60947-3
Switch-disconnectore Fuse-switch-disconnector
AC21A Ie AC22A Ie AC23A Ie
63 125A 63A 41A

100 125A 100A 41A
160 Use 200A 160A 160A
200 315A 200A 160A
315 Use 400A 315A 200A
400 400A 400A 200A
500 Use 630A 500A 385A
630 630A 630A 385A
800 800A 800A 500A
Operational performance
In accordance with BS EN 60947-3: A categories all ratings have been tested to values specified below:
Rated operational current, Ie (A) Operating cycles Total
Without current With current
63100 8,500 1,500 10,000

160315 7,000 1,000 8,000
400630 4,000 1,000 5,000
800 2,500 500 3,000

10.3 Technical data
Enclosed switch & fusegear
Glasgow parallel cable connection & copper terminal plate
35
CRS
Parallel cable connection
A = 803GNC
B = 6PCB
C = 90CSB/A CRS
An 802GCC (copper connection piece) is required in addition Copper terminal plate

to switch enclosure for parallel cable connection. Each copper terminal plate has 1-M16 x 50mm bolt, nut and washers for single hole
sockets. 4-M10 tapped holes are also provided for 4 hole sockets or solid copper.
Cable extension boxes dimensions

Eaton list Dimensions, mm
number A B C
1PCB 148 133 113

2PCB 148 209 113
3PCB 148 259 132
4PCB 302 347 184
5PCB 213 515 187
6PCB 213 515 327
Spreader boxes dimensions

Eaton list Dimensions, mm Fixing bolts
number A B C E F No. Type
Straight entry
50 CSB 83 232 170 67 171 4 M6
60 CSB 108 283 260 89 216 4 M8
70 CSB 133 384 322 114 318 4 M8
90 CSB 133 530 450 114 457 4 M10
45 Angled entry
50 CSBA 83 232 250 67 171 4 M6
60 CSBA 108 283 310 89 216 4 M8
70 CSBA 133 384 390 114 318 4 M8
90 CSBA 133 530 510 114 457 4 M10

Technical data
Busbar chambers
Eatons busbar chamber system is designed for wall-mounting installations. All units in the range share the same
height and depth dimensions. Similarly the twin busbars are located in precisely the same positions throughout
the range and vary in size only in their front-to-back dimensions according to rating. Detachable end plates
enable all units to be extended by coupling to a second busbar chamber using extension sets.

10.3 Technical data
Busbar chamber dimensions

Nominal Dimensions, mm
length, mm
A B C D E F G
550 562 364 222 280 474 4

900 912 364 222 280 824 4
1350 1362 364 222 280 1274 4
1800 1812 364 222 280 1724 862 6
Operational performance
In accordance with BS EN 60947-3 all ratings have been tested to values specified below:
Description Cycles
Operating cycles without current 8500

Operating cycles at rated current 1500
Total 10000

Technical data
Exel 2 dimensions
Current Dimensions, mm
rating, A A B C D E F G H J K
Switch-disconnectors
20 159 193 92 127 112 114 5.6 38.5 34
32 173 245 101 137 116 114 114 6.4 38.5 34
63 230 310 129 173 152 168 168 6.7 58 54
100/125 329 367 167 210 241 221 221 6.7 58 54
Switch-disconnector-fuses
20 219 193 92 127 171 114 5.6 38.5 34
32 267 245 101 137 209 114 114 6.4 38.5 34
63 351 310 129 173 273 168 168 6.7 58 54
100/125 503 367 167 210 416 221 221 6.7 58 54
Single hole fixing for 20A only
Performance values
Unit Short time withstand current Short circuit making capacity Rated fused short-circuit
(r.m.s. amps for 1 second) (peak amps at 415v ac) (prospective r.m.s. amps at 415v ac)
20A 640A 2.96 kA 80 kA

32A 960A 5.12 kA 80 kA
63A 2000A 6.62 kA 80 kA
100/125A 3750A 8.42 kA 80 kA

10.3 Technical data
Exel distribution fuseboards diversity factors

No. of ways Maximum rated operational current per way, Ie
200A 100A 63A 32A <20A
2 1
4 0.8 0.9 0.9 0.9 0.9
6 0.8 0.8 0.8 0.8
8 0.66 0.8 0.8 0.8
10 0.66
12 0.66
Therefore, incomer rating =
2 126A
4 640A 360A 227A 115A 72A
6 480A 302A 154A 96A
8 528A 403A 205A 128A
10 211A
12 253A
Exel distribution fuseboards enclosure dimensions IP4X (mm)

Nominal Poles Number A B C D crs E crs F dia.
rating, Ie of ways
20A SPN 4 386 304 148 252 191 8

6 386 304 148 252 191 8
8 386 368 148 252 255 8
12 386 448 148 252 335 8
TPN 4 631 304 148 442 191 8
6 631 304 148 442 191 8
8 631 368 148 442 255 8
32A SPN 4 386 304 148 252 191 8
6 386 304 148 252 191 8
8 386 368 148 252 255 8
12 386 496 148 252 383 8
TPN 4 710 304 148 576 191 8
6 710 304 148 576 191 8
8 710 368 148 576 255 8
10 710 448 148 576 335 8
12 710 496 148 576 383 8
63A TPN 2 546 473 227 458 369 10
4 972 330 227 884 226 10
6 972 330 227 884 226 10
8 972 473 227 884 369 10
100A TPN 4 1066 330 227 978 226 10
6 1066 549 227 978 445 10
8 1066 549 227 978 445 10
200A TPN 4 1560 529 270 1334 325 10
Exel distribution fuseboards earth bar terminal capacities

Description Nominal rating of fuseboard, Ie
20A 32A 63A 100A 200A
Main (stud) M10 M10 M10 M10 M10

Outgoing, mm2 10 10 25 25 70

Technical data
Exel distribution fuseboards main terminal stud sizes
Description No. of Nominal rating of fuseboard, Ie
ways 20A 32A 63A 100A 200A
SPN 4 M10 M10

6 M10 M10
8 M10 M10
12 M10
TPN 2 M12
3 M12
4 M10 M10 M12 M12 M16
6 M10 M10 M12 M16
8 M10 M10 M16 M16
10 M10
12 M10
1
Tunnel terminal 35mm2 max.
415V industrial fuselinks offset bolted contacts, dimensions

Eaton list Dimension, mm
number A max. B max. D max. E F G nom. H J
SA2 34 14 54 11 0.8 44.5 4.8

SA2M (2540A) 34 14 54 11 0.8 44.5 4.8
SA2M (5063A) 36 17.5 55 11 1.2 44.5 4.8
SB3 35 14 85 9 1.2 73 5.5 8
SB3M 56 22 86 9 1.2 73 5.5 8
SB4 35 17.5 86 9 1.2 73 5.5 8
SB4M 56 22 88 13 1.2 73 5.5 10
SO (80100A) 55 21 86 13 1.2 73 5.5 10
SOM 55 26 91 13 1.2 73 5.5 10
SO (125200A) 47 31 90 19 3.2 73 6.1
SD5 59 22 110 15 3.2 94 9
SD5M (125160A) 58 26 109 15 3.2 94 9 11
SB3, SB3M, SB4, SB4M, SD5M, SD6,
SD5M (200A) 47 31 110 19 3.2 94 9 10 SD6M, SO (80100A) & SOM types
SD6 47 31 110 19 3.2 94 9 10
SD6M 47 31 110 19 3.2 94 9 10

10.3 Technical data
415V industrial fuselinks centre bolted contacts, dimensions

Fuse link Dimensions, mm
type A max. B max. D max. E F G nom. H J L
SE3 57 22 114 13 1.6 97 7.1 10

SF3 57 22 129 14 1.6 111 8.7 12
SE4 57 22 114 13 1.6 97 7.1 10
SF4 57 22 129 14 1.6 111 8.7 12
SE4M 57 22 114 13 1.6 97 7.1 10
SF4M 58 21 126 14 3.2 111 8.7 11
SF5 59 22 127 14 3.2 111 8.7 11
SF5M (125160A) 58 26 126 14 3.2 111 8.7 11
SF5M200 47 31 136 19 3.2 111 9 12.5
SF6 47 31 136 19 3.2 111 9 12.5
SF6M 47 31 136 19 3.2 111 9 12.5
SF7 47 31 136 19 3.2 111 9 12.5
SF7 (315) 50 38 136 25 4.8 111 9 12.5
SF7M 50 38 136 25 4.8 111 9 12.5
SG7 47 59 158 19 3.2 133 10.5 12.5
SG7 (315) 50 38 209 25 4.8 133 10.5 12.5 25
SF8 50 39 136 25 4.8 111 9 12.5
SF8M 75 53 135 25 4.8 111 9 12.5
SH8 50 40 209 25 4.8 133 10.5 12.5 25.4
SH9 80 74 209 25 6.3 133 10.5 16 25.4
SY9 80 74 261 38 6.3 165 10.5 16 32
SH10 84 83 209 25 9.5 133 10.5 16 25.4
SY10 80 83 261 38 6.3 165 10.5 16 32
SJ11 83 100 198 63.5 9.5 149 14.3 19 32
Complete fuse units dimensions

Nominal Dimensions, mm Hole dia. (mm min) insulated stud
rating, In A B C D E F G H J K L (types C and D)
20A 87 79 27 50 63 56 6 5.5 12
32A 109 101 31 62 60 78 6 5.5 12.7 6.4 12
32A clip-in 75 25 57.7 6 5.5 4.4
63A 118 110 35 72 71 79 8 5.5 12.7 6.4 14.5
63A clip-in 88.7 31.5 66.34 8 5.5 4.8
100A 154 154 54 108 80 117 10 6.5 19 22 18.5
Compact range
32A 87 79 27 56 6 5.5 12
63A 109 101 31 78 6 5.5 12.7 6.4 12
100A 118 110 35 72 71 79 8 5.5 12.7 6.4 14.5
200A 154 154 54 108 80 117 10 6.5 19 22 18.5

Technical data
Local switch-disconnectors - rotary isolators, 2063A, IP65, 38 poles
AC-23A Rating (kW) AC-3 rating, motor load switch (kW)
Nominal unit 400V 3ph 230V 1ph 230V 230V star 400V 400V star delta Rated short-time Terminal capacity
rating Ie (A) delta withstand current (flexible with
Icw 1s (A) ferules) (mm2)
20 6.5 3.5 3 4 4 4.5 320 1 x 0.75 - 1.5

2 x 0.75 - 1.5
25 13 7 5.5 5.5 7.5 7.5 640 1x1-4
2x1-4
32 13 7.5 6.5 11 12 18.5 650 1 x 0.75 - 4
2 x 0.75 - 4
(3 & 3+N pole) 30 18.5 15 15 30 30 1260 1 x 1.5 - 25
2 x 1.5 - 6
(6 & 8 pole) 22 15 15 22 22 37 1300 1 x 1.5 - 25
2 x 1.5 - 10
Local switch-disconnectors - rotary isolators, 2063A, IP65, 38 poles dimensions

Eaton List Number A B C D E F G H I
207149-GV 137 120 80 75 35 M20 - - -

207151-GV 137 120 80 75 35 M20 - - -
207153-GV 137 120 80 95 35 M20 - - -
207161-GV 137 120 80 95 35 M20 - - -
226902-GV 180 160 100 80 35 M25 - M25 8
227860-GV 180 160 100 80 35 M25 - M25 8
207202-GV 180 160 100 100 35 M25 - M25 8
207210-GV 180 160 100 100 35 M25 - M25 8
207212-GV 180 160 100 100 35 M25 - M25 8
207348-GV 240 - 160 95 44 M25 / M32 M20 - -
207349-GV 240 - 160 95 44 M25 / M32 M20 - -
207350-GV 240 - 160 95 44 M25 / M32 M20 - -
207246-GV 240 - 160 160 44 - - - -
207248-GV 240 - 160 160 44 - - - -
Dimensions (mm)
I ON
o B A
OFF
o
OFF
H H
C D E
F G

10.3 Technical data
Rotary change over isolators, 2063A, IP65, 4 poles

AC-23A Rating (kW) AC-3 rating, motor load switch (kW)
Nominal unit 400V 3ph 230V 1ph 230V 230V star 400V 400V star delta Rated short-time Terminal capacity
rating Ie (A) delta withstand current (mm2)
Icw 1s (A)
20 6.5 3.5 3 4 4 5.5 320 1 x 1 - 2.5

2 x 1 - 2.5
32 13 7.5 6.5 11 12 18.5 650 1 x 1- 6
2 x 1- 6
63 22 15 15 22 22 37 1300 1 x 2.5 - 35
2 x 2.5 - 16
Local switch-disconnectors - rotary isolators, 2063A, IP65, 38 poles dimensions

Nominal unit
rating
Ie (A) A B C D E F G H I
20 137 120 80 95 27 M20 - - -

32 180 160 100 100 35 M25 - M25 8
63 240 - 160 160 29 M25 / M32 M20 - -
Dimensions (mm)
I ON
o B A
OFF
o
OFF
H H
C D E
F G

Technical data
AC motors, 3 phase full load current table, 1450rpm approx.
Provided as a guide to the selection of suitable Eaton control gear
The tables are based on motors of approx, 1450 rpm of average efficiency and power factor. Motors of higher speed
than 1450 rpm usually take a lower current than that shown in the table; while motors of lower speed usually take
higher current. Wide variations from these figures can arise, especially on single phase motors and engineers should,
whenever possible, determine the actual full load current (F.L.C.) from the motor rating plate in each case
Motor rating Approx F.L.C. at line voltage
kW 220V 240V 380V 400415V 550V
0.07
0.1 0.7 0.6 0.4 0.4 0.3
0.12 1 0.9 0.5 0.5 0.3
0.18 1.3 1.2 0.8 0.7 0.4
0.25 1.6 1.5 0.9 0.9 0.6
0.37 2.5 2.3 1.4 1.3 0.8
0.56 3.1 2.8 1.8 1.6 1.1
0.75 3.5 3.2 2 1.8 1.4
1.1 5 4.5 2.8 2.6 1.9
1.5 6.4 5.8 3.7 3.4 2.6
2.2 9.5 8.7 5.5 5 3.5
3 12 11 7 6.5 4.7
3.7 15 13 8 8 6
4 16 14 9 8 6
5.5 20 19 12 11 8
7.5 27 25 16 15 11
9.3 34 32 20 18 14
10 37 34 22 20 15
11 41 37 23 22 16
15 64 50 31 28 21
18.5 67 62 39 36 26
22 74 70 43 39 30
30 99 91 57 52 41
AC motors, 1 phase full load current table, 1450rpm approx.

Motor rating Approx F.L.C. at line voltage
(kW) 110V 220V 230240V
0.07 2.4 1.2 1.1

0.1 3.3 1.6 1.5
0.12 3.8 1.9 1.7
0.18 4.5 2.3 2.1
0.25 5.8 2.9 2.6
0.37 7.9 3.9 3.6
0.56 11 5.5 5
0.75 15 7.3 6.7
1.1 21 10 9
1.5 26 13 12
2.2 37 19 17
3 49 24 22
3.7 54 27 25
4 60 30 27
5.5 85 41 38
7.5 110 55 50

10.3 Technical data
9kW DOL starter without switch disconnect, IP 65 moulded surface mounting enclosure, dimensional drawings
2 X 5.3mm DIA
Elongated Fixing Holes
4 X 21.5mm
50.5 mm Conduit Knockouts
20mm
120.0 mm
140.0 mm
150 mm
166 mm
150 mm 5.3
88 mm
11kW DOL starter without switch disconnect, IP 54 metalclad surface mounting enclosure, dimensional drawings
Dimensions in brackets refer to type 2528ADS(2X) size enclosure
(30.0 mm)
28.5 mm
159.4 mm
(223 mm)
129.2 mm
105.8 mm
(172 mm)
(141mm)

Technical data
11kW DOL starter without switch disconnect, IP 54 metalclad surface mounting enclosure, dimensional drawings (contd)
2 X 6.0 DIA Fixing Holes

(3 X 6.0 DIA Fixing Holes)
18 mm
25 mm 38 mm 6-20mm
(47 mm) Conduit Knockout
(7-20/25mm
Conduit Knockout)
(41.mm)
29 mm
(165.0mm)
117.5mm
(168.5 mm)
(154 mm)
125.5 mm
112 mm
= =
(80.0 mm Fixing Holes)

100 mm
(137 mm)
Dimensions in brackets refer to

types 2528ADS(2X) & 3228ADS(3X)
11kW DOL starter with switch disconnect, IP 54 metalclad surface mounting enclosure, dimensional drawings
sized enclosures
Outline and 221.5 mm

29mm
Knockout Dimensions
34 mm
159.5 mm
154 mm
140mm
185mm
)
29 mm
Box Fixing Dimensions
171.5 mm
4-6.0 Diameter
Fixing Holes
114 mm

10.3 Technical data
11kW DOL reversing starter without switch disconnect, IP 54 metalclad surface mounting enclosure, dimensional drawings
8 X 20.9mm (3/4) conduit knockouts are provided for cable entry at top,bottom and side of the enclosure and the earth
terminal may be reversed for external connection but the components must be assembled in the same order as supplied.
Outline and Knockout Dimensions

221.5 mm
29mm
34 mm
Forward Reverse
159.5 mm
MEM
154 mm
166.5 mm
140mm

29 mm
171.5 mm
4-6.0 Diameter
Fixing Holes
114 mm
20 MM CONDUIT KNOCKOUTS

Technical data
22kW Star Delta starter without switch disconnect, IP 54 metalclad surface mounting enclosure, dimensional drawings
Star Delta starter enclosure (IP54 to BSEN60529:1992) 20.9mm (3/4) conduit knockouts are provided
for cable entry at top, bottom and side of the enclosure and the earth terminal may be reversed for
external connection, but the components must be assembled in the same order as supplied.
221.5 mm
29 mm*
34 mm
159.5 mm
MEM
154 mm
(53 mm)
29 mm
140 mm
166.5 mm (155 mm)
= =
171.5 mm
4 - 6.0 mm
= = Diameter
Fixing Holes
114 mm
=
=
STAR DELTA STARTER ENCLOSURE (IP54 to BSEN60529:1992).

8 X 20.9mm (3/4) conduit knockouts are provided for cable entry at top, bottom and side of the enclosure and
The earth terminal may be reversed for external connection but the components must be assembled in the
same order as supplied.
OUTLINE AND KNOCKOUT DIMENSIONS
View shows type 28/48SDA2X18
Dimensions in brackets ( ) are for types
28/48SDA3X25 and 28/48SDA3X32

10.3 Technical data
11kW DOL starter without switch disconnect, moulded & metal surface mounting enclosure, wiring diagrams
A. Three phase motors-DOL starter. Local 3-wire (pushbutton) control.
Supply 17 18 A2
Start
Remote
Push Inch
Y Z Buttons
A1 L1 L2 L3 Stop
13
14 17
A2 1 3 5
18 Start Remote start/inch/stop control

Connect as above except remove lead
96 97
X and add connections shown.
O
95 98 Stop
2 4 6
X
Motor
B. Single phase motors-DOL starter. Local 3-wire (pushbutton) control.
17 18 A2
Connect Supply
Cable N L Start
Remote
Push
Buttons Stop
Y Z
A1 L1 L2 L3 13
17
A2 1 3 5 14
18 Start Local & remote 3-wire

96 97
(pushbutton) control
O Connect as above except remove lead

X and add connections shown.
2 4 6
95 98 Stop
X
N L
Motor
Coil phase to neutral: remove connector Y, connect Neutral to A1
Separate coil supply: remove connectors Y and Z, connect coil supply to A1 and 96.
Coil voltage: Ensure correct voltage coil is fitted for separate coil supply and phase to neutral applications.
External interlock: Remove connection Z and insert interlock between 5 and 96.
Alarm circuit: At trip an alarm signal voltage equal to the coil voltage is available between 98 and A1
when a link is added between 96 & 97. The switch is rated at 440VA, 500V maximum.
Control circuit fuses (10A MAX).
Coil connected Phase to neutral (1 fuse): remove connector Z and connect fuse between 5 and 96.
Coil Connected Phase to Phase (2 fuses): remove connector Z and connect fuse between
5 and 96. Remove connector Y and connect fuse between 1 and A1.
Note: the voltage rating of the fuse(s) must be suitable for the control circuit voltage.
Short circuit protection: Maximum sizes of fuses or MCBs to give short-circuit protection to this starter are tabulated on page 173.
To reverse direction of rotation (3-Phase Motors): Interchange any two supply lines 1, 3 or 5.

Technical data
11kW DOL starter with switch disconnect, IP 54 metalclad surface mounting enclosure, wiring diagrams
Three phase motors-DOL starter isolator local 3-wire (pushbutton) control
Supply 17 18 A2
(L1) (L2) (L3)
1 3 5
Start
Remote
Push Inch
Buttons
Y Z
A1 L1 L2 L3 13 Stop
17
A2 1 3 5 14
Start
18 Isolator
Switch Remote start/inch/stop control
96 97
Connect as above except remove lead
O X and add connections shown
2 4 6 95 Stop
98
X
Motor
Single phase motors-DOL starter isolator local 3-wire (pushbutton) control

Connect supply to 1 and 5 at the isolator. Connect motor to 4 and 6 at the
overload relay. Remove existing cable P and connect a cable of cross-
sectional area equal to the supply cable between 2 and 3 as shown.
Connect
Supply 17 18 A2
Cable (L) (N)
1 5 Start
Remote
Push
Buttons Stop
P
Y Z
A1 L1 L2 L3 13
14 17 Local & remote 3-wire
A2 1 3 5
Start (pushbutton) control
18 Connect as above except remove lead
Isolator
96 97 Switch X and add connections shown
95 O
2 4 6 Stop
X 98
Motor
Coil phase to neutral: remove connector Y, connect Neutral to A1

Separate coil supply: remove connectors Y and Z, connect coil supply to A1 and 96.
5 and 96. Remove connector Y and connect fuse between 1 and A1.
Note: the voltage rating of the fuse(s) must be suitable for the control circuit voltage.
External interlock: Remove connection Z and insert interlock between 5 and 96.
when a link is added between 96 & 97. The switch is rated at 440VA, 500V maximum.

10.3 Technical data
11kW DOL reversing starter without switch disconnect, IP 54 metalclad surface mounting enclosure, wiring diagrams
Circuit Diagrams:- Power Control Remote Control Option

5 R
Z
5 R
96
95 REMOTE PB 96
1 3 5 1 3 5 95
17 53 17 53 REMOVE LINK FOR
OFF
REMOTE OPERATION
F F R R
2 4 6 2 4 6 17 53 17 53
F R 18 54 18 54
21 21 F F R R
R F 54
ON(R) ON(F) 18 18 54
22 22
A2 A2
F R 21 21
2 4 6 R F
A1 A1 22 22
A2 A2
Y F R
A1 A1
1 R
L1
L2 Mechanical Iinterlock
L3 1 R
A1 1 3 5 21 A1 1 3 5 21 Separate Supply of Mechanical Interlock

Control Circuit
53 63 17 53 63 17
F R ON F
54 64 18 54 64 18 OFF
ON R
2 4 6 22 A2 2 4 6 22 A2
A1 1 5
98 97 95 96 53
2 4 6 F R
R 54 54
U V W
14
95
M
3 96
Option for Remote Control
Coil phase to neutral: Remove connector Y, connect Neutral to A1 F

Separate coil supply: Remove connectors Y and Z, connect coil supply to A1 R and 96.
5 and 96. Remove connector Y and connect fuse between 1 and A1 R.
Note: The voltage rating of the fuses must be suitable for the control circuit voltage.
External interlock: Remove connector Z and connect interlock between 5 and 96. When using
remote control, connect external interlock in series with remote 2 wire (switch control).
To reverse direction of rotation: (3 Phase Motors) interchange any two supply lines 1, 3 or 5.
when a link is added between 96 and 97. The switch is rated at 400VA, 500V maximum.
Limit Switch Connections

Forward limit: Remove connection between 54Forward and 21Reverse connect limit switch between 54F and 21R.
Reverse limit: Remove connection between 54Reverse and 21Forward- connect limit switch between 54R and 21F.

Technical data
25kW Star Delta starter without switch disconnect, IP 54 metalclad surface mounting enclosure, wiring diagram
Circuit Diagram; Power Control Remote Control Option

5
5
Z D D
1 3 5 1 3 5 1 3 5 Z
M D S 96
96
Remote PB
2 4 6 2 4 6 2 4 6 95 95
17 13 OFF Remove link for
Remote Operation
13
D M M
2 4 6 18 14
ON 14
53
53
Power Connections to be made S
L1 S
54 68
L2 54
55 68
L3 M M 55
M M
1 3 5 1 3 5 1 3 5 56 67
56 67
21 21
M D 21 21
S D S
D S
22 22
2 4 6 2 4 6 2 4 6 22 22
A2 A2 A2
U1 V1 W1 A2 A2 A2
S M D
S M D
M 2 4 6
3 A1 A1 A1
V2 W2 U2 A1 A1 A1
Y
U2 V2 W2
D Y
1 D
1
Control Connections
ON
to be made X X
OFF
1. Coil Voltage same as Power A1 1 5 13

Voltage No Change
M D S M D S
54
2. Coil Voltage different to Power 14
Voltage Scheme A
96 95
3. Remote Control Option A
Scheme B X B
Short circuit protection

Overload Relay list number Motor FLC Ie (A) SCPD Back-up protection Back-up protection
MAX HRC fuse BS88:1 aM (A) Max MCB Type C
Direct on line
8TT87 0.631 4 EMCH306
8TT88 11.6 6 EMCH306
8TT89 1.62.5 10 EMCH306
8TT90 2.54 16 EMCH310
8TT91 46 16 EMCH310
8TT98 5.58.0 20 EMCH316
8TT92 710 25 EMCH320
8TT93 1013 32 EMCH320
8TT94 1318 40 EMCH332
8TT104 1825 50 EMCH340
Star Delta
8TT90SD 4.36.9 16 EMCH310
8TT91SD 6.910.4 16 EMCH310
8TT98SD 9.513.8 20 EMCH316
8TT92SD 12.117.3 25 EMCH320
8TT93SD 17.322.5 32 EMCH320
8TT94SD 22.531 40 EMCH332
8TT104SD 3143 50 EMCH340

10.3 Technical data
Heating and lighting contactors
6-20mm
(34.5 mm)
Conduit Knockout
21 mm
(7-20/25mm
Conduit Knockout)
(159.4 mm)
117.5 mm
(165 mm)
(223 mm)
(80 mm)
116.5mm 105.8 mm 2-Fixing Holes

(125 mm) (141 mm) 6.3 mm DIA
(3-Fixing Holes
6.3 mm DIA)
Dimensions in brackets ( ) refer to 228ALDPR, 228ALCSPN/R, 428ALCFP/R, 448ALCFP, 428ALCDP/R,

428ALCSPN/R. All others REFER
DIMENSIONS TO:-
refer to list numbers; 228ALCFP/R, 248ALCFP and 228ALCDP.
228ALCFP, 248ALCFP, 228ALCDP, 228ALCDPR *, 228ALCFPR
DIMENSIONS
Additional IN BRACKETS
side mounting ( ) REFER
auxilary contacts TO:-
for DOL, DOL reversing, Star Delta starters and Autoline
1NC Ith 10A Ui228ALCSPNR*,
228ALCSPN,
1 NO, 600v 428ALCFP, 448ALCFP, 428ALCDP, 428ALCDPR *, 428ALCSPN,
428ALCSPNR
Description * Current rating Coil voltage Starter list Maximum side Eaton list
(A) number mount auxilaries number
DOL Starter 25 220240 28ADS2X 2 8TA8DN11

DOL Starter 25 380415 48ADS2X 2 8TA8DN11
Starter with disconnector 18 220240 28ADSA1X 2 8TA8DN11
Reversing starter 18 220240 28ARD1X 1 reverse, 1 forward 8TA8DN11
Star Delta starter 18 220240 28SDA2X18 1 main, 1 star 8TA8DN11
Autoline 4 pole 230240 228ALCFP 2 8TA8DN11
Autoline 4 pole with rectifier 230240 228ALCFPR 1 8TA8DN11

Technical data
Additional side mounting auxilary contacts for DOL, DOL reversing, Star Delta starters and Autoline (contd)
Description Current rating Coil voltage Starter list Maximum side Eaton list
(A) number mount auxilaries number

Autoline 2 pole 230240 228ALCDP 2 8TA8DN11
Autoline 2 pole with rectifier 230240 228ALCDPR 1 8TA8DN11
Autoline 1 pole and neutral 230240 228ALCSPN 1 8TA8DN11
Autoline 1 pole and neutral with rectifier 230240 228ALCSPNR 1 8TA8DN11
Autoline 4 pole with rectifier 230240 428ALCFPR 1 8TA8DN11
Autoline 2 pole 230240 428ALCDP 2 8TA8DN11
Autoline 2 pole with rectifier 230240 428ALCDPR 1 8TA8DN11
Autoline 1 pole and neutral 230240 428ALCSPN 1 8TA8DN11
Autoline 1 pole and neutral with rectifier 230240 428ALCSPNR 1 8TA8DN11
Replacement front mounting auxiliary contacts for Star Delta

1 NO, 1NC Ith 10A Ui 600v
For Star Delta Front mounting auxilary
Eaton list
number
8TA1DN11
28SDA2X18
8TA1DN11
28SDA2X25
8TA1DN11
28SDA2X32
8TA1DN11
48SDA2X18
8TA1DN11
48SDA2X25
8TA1DN11
48SDA2X32
Tightening torques for Star Delta and DOL starters

Starter type Maximum starter Relay tightening torque (Nm) Contactor tightening torque
(Nm) rating (kW) Power Aux Power Aux
DOL 9 1.85 1.2 1.7 1.2

DOL 11 1.85 1.2 1.85 1.85
DOL 15 2.5 1.2 2.5 1.2
Star delta 15 1.85 1.2 1.7 1.2
Star delta 22 1.85 1.2 1.85 1.85
Star delta 25 2.5 1.2 2.5 1.2
Tightening torques for Autoline contactors

Starter type Contactor tightening torque (Nm)
Power
228ALCFP 1.7
248ALCFP 1.7
428ALCFP 2.5
448ALCFP 2.5
228ALCFPR 1.7
428ALCFPR 2.5
228ALCDP 3.0
428ALCDP 3.5
228ALCDPR 3.0
428ALCDPR 3.0
228ALCSPN 3.5
428ALCSPN 4.0
228ALCSPNR 4.0
428ALCSPNR 4.0

10.3 Technical data
8TT series, overload relay tripping characteristics
Balanced operation, 3phase, from cold state

Balanced operation, 3phase, after a long period at the set current (hot state)
Operation following the loss of one phase (single phase tripping) from cold state

Technical data
Contactor utilisation category, AC1 (Ue_<440v) electrical life curve

10.3 Technical data

Technical data
MSU pushbutton control units (moulded IP66) dimensions
M20 M20
44
66.5
80
C M4
33
b
a
M20/M25
17.8
56
d (max button height)

M20 48 M20
Dimensions Dimensions Dimensions Dimensions Cable entries Eaton list a

a (mm) b (mm) c (mm) d (mm) number
72 42.6 58.5 10 2 x M16 3 x M20 2 x M25 M21MSSU

72 42.6 58.5 16.4 2 x M16 3 x M20 2 x M25 M21MSU
72 42.6 58.5 20.6 2 x M16 3 x M20 2 x M25 M21MSU2K
72 42.6 58.5 20.6 2 x M16 3 x M20 2 x M25 M21MSU2SK
72 42.6 58.5 48 2 x M16 3 x M20 2 x M25 M21MSULK
72 42.6 58.5 48 2 x M16 3 x M20 2 x M25 M21MSUML
120 85.6 106.5 16.4 2 x M20 3 x M20 2 x M25 M22MSU
120 85.6 106.5 48 2 x M20 3 x M20 2 x M25 M22MSUL
153 118.6 139.5 48 2 x M20 2 x M25 4 x M20 M23MSUL

10.4 Technical data
Non-auto capacitor dimensions
FIXING HOLES
12mm DIA
C
A
D
E
KVAR (415V) A B C D E
25 190 190 376 212 245

50 190 190 376 212 245
75 346 190 628 405 435
100 346 190 628 405 435
Non-auto capacitor specification
Manufacturing standards: IEC 61439-2, IEC 60439-1

Voltage range: Standard voltage 400V capacitors suitable for use on other voltages (200660V) supplied on request
Frequency range: 50Hz or 60Hz (dependent on customer specification)
Phases: 3 phase (single phase on request)
Terminals: 3 Terminal standard (2 and 6 on request)
Discharge resistors: Fitted as standard and permanently connected across the capacitor terminals
Customer connections: By means of M4, 6, 8, 10, 12 brass set screws. The size of screw dependent on capacitor size
Case material: Zinc plated steel
Case thickness: 1mm
Location: Interior (exterior cases are available on request)
Protection: IP21
Ambient temperature: 25 +40C
Losses (including discharge resistors): Less than 0.5 watts/kvar
Cubicle paint colour: Light grey RAL 7035
Variations to above specifications available on request.

Technical data
100 capacitor dimensions
FIXING HOLES
12mm DIA
G
FIXING HOLES
12mm DIA
G
E
D
B A E
F
KVAR (415V) A B C D E F G
25 B A 400 200 905 425 245 253 n/a

50 F 400 200 905 425 455 253 n/a
75 390 350 980 425 455 403 215
100 390 350 980 425 455 403 215
100 capacitor specification

Voltage range: Standard voltage 400V capacitors suitable for use on other voltages (200660V) supplied on request
Frequency range: 50Hz or 60Hz (dependent on customer specification)
Phases: 3 phase (single phase on request)
Terminals: 3 terminal standard (2 and 6 on request)
Discharge resistors: Fitted as standard and permanently connected across the capacitor terminals
Customer connections: By means of M4, 6, 8, 10, 12 brass set screws. The size of screw dependent on capacitor size
Case material: Zinc plated steel
Case thickness: 1mm
Location: Interior (exterior cases are available on request)
Protection: IP21
Ambient temperature: 25 +40C
Losses (including discharge resistors): Less than 0.5 watts/kvar
Cubicle paint colour: Light grey RAL 7035

10.4 Technical data
300 standard cubicle dimensions
G
FIXING HOLES
16mm DIA
C
D
J
H
B A
E
KVAR (415V) A B C D E1) F G H J
125 600 600 2100 2000 680 455 487 440 430
150 600 600 2100 2000 680 455 487 440 430
175 600 600 2100 2000 680 455 487 440 430
200 600 600 2100 2000 680 455 487 440 430
225 600 600 2100 2000 680 455 487 440 430
250 600 600 2100 2000 680 455 487 440 430
275 600 600 2400 2300 680 455 487 440 430
300 600 600 2400 2300 680 455 487 440 430
1)
Not applicable for direct connection
300 standard cubicle specifications

Voltage Range: Standard operating voltages 380/400/415Vac, 3ph
Frequency range: 50Hz (60Hz rating on request)
Cable chamber and customer cable entry arrangements: Undrilled detachable gland plate. Top or bottom entry as required.
Cubicle material: 2mm mild steel enclosure (1.6mm doors) painted light grey - RAL 7035 (other colours dependant on customer specification)
Earthing: Internal earth bar linked to framework.
Fixing: Floor fixing by means of 4 x 16mm diameter holes per cubicle.
Protection: IP31 indoor. (IP42 on request Derating may be required)
Ambient temperature: -25C +55C.
Terminal compartment
A terminal compartment is fitted as standard complete
with suitably rated incoming connection points*.
Alternatively, an incoming protective device
can be fitted to the incoming section.
The device can be fitted to the top or bottom of the capacitor bank.
A detachable undrilled gland plate is fitted as standard.
To accept top or bottom cable entry. Cable entry
will be bottom, unless otherwise specified.
* Accomodation of oversized cables is available, if specified.

Technical data
300 detuned cubicle dimensions
G FIXING HOLES
16mm DIA
C
D
F
J
H
B A
E
KVAR (415V) A B C D E1) F G H J
100 600 600 2400 2300 680 455 487 440 430
125 600 600 2400 2300 680 455 487 440 430
150 600 600 2400 2300 680 455 487 440 430
175 1200 600 2400 2300 680 455 487 440 430
200 1200 600 2400 2300 680 455 487 440 430
225 1200 600 2400 2300 680 455 487 440 430
250 1200 600 2400 2300 680 455 487 440 430
275 1200 600 2400 2300 680 455 487 440 430
300 1200 600 2400 2300 680 455 487 440 430
325 1200 600 2400 2300 680 455 487 440 430
350 1200 600 2400 2300 680 455 487 440 430
375 1200 600 2400 2300 680 455 487 440 430
400 1200 600 2400 2300 680 455 487 440 430
425 1800 600 2400 2300 680 455 487 440 430
450 1800 600 2400 2300 680 455 487 440 430
475 1800 600 2400 2300 680 455 487 440 430
500 1800 600 2400 2300 680 455 487 440 430
525 1800 600 2400 2300 680 455 487 440 430
550 1800 600 2400 2300 680 455 487 440 430
575 1800 600 2400 2300 680 455 487 440 430
600 1800 600 2400 2300 680 455 487 440 430
1)
Not applicable for direct connection
300 detuned cubicle specifications

Voltage range: Standard operating voltages 380/400/415Vac, 3ph
Frequency range: 50Hz (60Hz rating on request)
Cable chamber and customer cable entry arrangements: Undrilled detachable gland plate. Top or bottom entry as required
Cubicle material: 2mm mild steel enclosure (1.6mm doors) painted light grey - RAL 7035 (other colours dependant on customer specification)
Earthing: Internal earth bar linked to framework
Fixing: Floor fixing by means of 4 x 16mm diameter holes per cubicle
Protection: IP31 indoor. (IP42 on request derating may be required)
Ambient temperature: -25C +55C

10.5 Technical data
Degrees of protection IP
The degrees of protection against ingress of foreign bodies

and liquids are indicated by the first two characteristic
numerals as detailed in tables 1 and 2. For switch and
control gear the classification is recognised internationally
and is described in detail in BS EN 60529.
First number
Protection against solid foreign objects Meaning protection of persons against
IP Requirements access to hazardous parts with:
0 No protection non-protected
1 Full penetration of 50mm diameter sphere not allowed. Contact with hazardous parts not permitted back of hand
2 Full penetration of 12.5mm diameter sphere not allowed finger
The jointed test finger shall have adequate clearance from hazardous parts
3 The access probe of 2.5mm diameter shall not penetrate tool
4 The access probe of 1.0mm diameter shall not penetrate wire
5 Limited ingress of dust permitted (no harmful deposit) wire
6 Totally protected against ingress of dust wire
Second number
Protection against harmful ingress of water Meaning protection from water
IP Requirements
0 No protection. non-protected
1 Protected against vertically falling drops of water limited ingress permitted vertically dripping
2 Protected against vertically falling drops of water dripping up to 15 from the vertical
with enclosure tilted 15 from the vertical limited ingress permitted
3 Protected against sprays to 60 from the vertical limited ingress permitted limited spraying
4 Protected against water splashed from all directions limited ingress permitted splashing from all directions
5 Protected against low pressure jets of water from all directions limited ingress permitted hosing jets from all directions
6 Protected against strong jets of water limited ingress permitted strong hosing jets from all directions.
7 Protected against the effects of immersion between 15cm and 1m temporary immersion
8 Protected against long periods of immersion under pressure continuous immersion
Additional letter
(Optional) Meaning protection of persons against
IP Requirements access to hazardous parts with:
A for use with O Penetration of 50mm diameter sphere up to guard face must not contact hazardous parts. back of hand
B for use with 0 & 1 Test finger penetration to a maximum of 80mm must not contact hazardous parts. finger
C for use with 1 & 2 Wire of 2.5mm diameter x 100mm long must not contact tool
hazardous parts when spherical stop face is partially entered.
D for use with 1, 2 & 3 Wire of 1.0mm diameter x 100mm long must not contact wire
hazardous parts when spherical stop face is partially entered.
Note: limited penetration allowed with all four additional letters.

Indices
Eaton list number index
131669...................................................................................40 1 SCHF..................................................................................112 16SN2..................................................................................108

158053...................................................................................40 100 SCHF..............................................................................112 16SP.....................................................................................108
158056...................................................................................40 1000MEB..............................................................................101 16SS.....................................................................................110
167375...................................................................................58 1000SJ11.............................................................................108 1CLX.....................................................................................103
167376...................................................................................59 1004R...................................................................................108 1PCB.......................................................................................95
167377...................................................................................58 1004RL.................................................................................108 2 BBCL....................................................................................99
167378...................................................................................58 1004XTNC............................................................................103 2 SCHF..................................................................................112
167379...................................................................................56 1006XTNC............................................................................103 200 FSCS................................................................................98
167380...................................................................................57 1008XTNC............................................................................103 2004XTNC............................................................................103
167381...................................................................................56 100AXD2..............................................................................100 200CMFB..............................................................................112
167382...................................................................................56 100AXTN2............................................................................100 200JCS82.............................................................................111
167383...................................................................................56 100CMFB..............................................................................112 200JCS92.............................................................................111
167384...................................................................................60 100CMFC..............................................................................112 200SD6.................................................................................107
167385...................................................................................60 100JCS82.............................................................................111 200SD6M250.......................................................................107
167386...................................................................................60 100JCS92.............................................................................111 200SD6M315.......................................................................107
167387...................................................................................60 100KXDC2F..........................................................................100 200SF6.................................................................................107
167389...................................................................................55 100KXSC2F...........................................................................100 200SF6M250........................................................................107
167390...................................................................................55 100KXTNC2F........................................................................100 200SF6M315........................................................................107
167391...................................................................................55 100MBDEBSP.......................................................................101 200SO...................................................................................106
167392...................................................................................55 100MFA................................................................................112 201GNC..................................................................................94
167398...................................................................................55 100MFB................................................................................112 202GCEBSP............................................................................97
169584.............................................................................39, 50 100MFC................................................................................112 203GNC..................................................................................94
169585.............................................................................39, 50 100MFLK......................................................................103, 112 203GNL..................................................................................94
169586.............................................................................39, 50 100SD5.................................................................................106 204GC.....................................................................................94
169587.............................................................................39, 50 100SD5M125.......................................................................106 204R.....................................................................................108
169588.............................................................................39, 50 100SD5M160.......................................................................106 204XSNC..............................................................................103
169589.............................................................................39, 50 100SD5M200.......................................................................106 204XTNC..............................................................................103
169590.............................................................................39, 50 100SF5.................................................................................107 206XSNC..............................................................................103
169591.............................................................................39, 50 100SF5M125........................................................................107 206XTNC..............................................................................103
169592.............................................................................39, 50 100SF5M160........................................................................107 207136-GV...........................................................................102
169593.............................................................................39, 50 100SF5M200........................................................................107 207149-GV...........................................................................102
169594..............................................................................39,50 100SO...................................................................................106 207151-GV...........................................................................102
169598.............................................................................39, 50 100SOM125.........................................................................106 207153-GV...........................................................................102
169599.............................................................................39, 50 100SOM160.........................................................................106 207161-GV...........................................................................102
169600.............................................................................39, 50 101GNC..................................................................................94 207191-GV...........................................................................102
169601.............................................................................39, 50 102GCEBSP............................................................................97 207202-GV...........................................................................102
169602.............................................................................39, 50 103GNC..................................................................................94 207210-GV...........................................................................102
169603.............................................................................39, 50 103GNL..................................................................................94 207212-GV...........................................................................102
169604.............................................................................39, 50 104GC.....................................................................................94 207230-GV...........................................................................102
169605.............................................................................39, 50 10LS.....................................................................................110 207246-GV...........................................................................102
169606.............................................................................39, 50 10SA2...................................................................................106 207248-GV...........................................................................102
169607.............................................................................39, 50 10SB3...................................................................................106 207348-GV...........................................................................102
169608..............................................................................39,50 10SE3...................................................................................107 207349-GV...........................................................................102
169609.............................................................................39, 50 10SF3...................................................................................107 207350-GV...........................................................................102
169610.............................................................................39, 50 10SN2..................................................................................108 208XSNC..............................................................................103
169611.............................................................................39, 50 10SS.....................................................................................110 208XTNC..............................................................................103
169612.............................................................................39, 50 11 BBMS................................................................................99 20LS.....................................................................................110
169613.............................................................................39, 50 1250SJ11.............................................................................108 20MFA..................................................................................112
169614.............................................................................39, 50 125AXTN2............................................................................100 20MFB..................................................................................112
169618.............................................................................39, 50 125JCS82.............................................................................111 20MFC..................................................................................112
169619.............................................................................39, 50 125JCS92.............................................................................111 20SA2...................................................................................106
169620.............................................................................39, 50 125KXTNC2F........................................................................100 20SA2M25...........................................................................106
169621.............................................................................39, 50 125SD6.................................................................................107 20SA2M32...........................................................................106
169636.............................................................................39, 50 125SF6.................................................................................107 20SB3...................................................................................106
169637.............................................................................39, 50 125SO...................................................................................106 20SE3...................................................................................107
169638.............................................................................39, 50 142 BBC..................................................................................98 20SF3...................................................................................107
169639.............................................................................39, 50 143 BBC..................................................................................98 20SN2..................................................................................108
169640.............................................................................39, 50 144 BBC..................................................................................98 20SN2M25...........................................................................108
169641.............................................................................39, 50 146 BBC..................................................................................98 20SN2M32...........................................................................108
169642.............................................................................39, 50 151GNC..................................................................................94 20SP.....................................................................................108
169643.............................................................................39, 50 153GNC..................................................................................94 20SS.....................................................................................110
169644.............................................................................39, 50 154GC.....................................................................................94 21 BBMS................................................................................99
169645.............................................................................39, 50 154R.....................................................................................108 2100AXEBSP........................................................................101
169646.............................................................................39, 50 15AXD2................................................................................100 212XSNC..............................................................................103
169647.............................................................................39, 50 15AXTN2..............................................................................100 226902-GV...........................................................................102
169648.............................................................................39, 50 15KXDC2F............................................................................100 227860-GV...........................................................................102
169649.............................................................................39, 50 15KXSC2F.............................................................................100 228ALCDP............................................................................119
169650.............................................................................39, 50 15KXTNC2F..........................................................................100 228ALCDPR..........................................................................119
169651.............................................................................39, 50 160JCS82.............................................................................111 228ALCFP.............................................................................119
169652.............................................................................39, 50 160JCS92.............................................................................111 228ALCFPR...........................................................................119
169670.............................................................................39, 50 160SD6.................................................................................107 228ALCSPN..........................................................................119
169671.............................................................................39, 50 160SF6.................................................................................107 228ALCSPNR........................................................................119
259471...........................................................67, 71, 75, 79, 83 160SO...................................................................................106 230AXEBSP..........................................................................101
259499.......................................................................75, 79, 83 16LS.....................................................................................110 230KXEBSP..........................................................................101
259744...........................................................67, 71, 75, 79, 83 16SA2...................................................................................106 242 BBC..................................................................................98
259763...........................................................67, 71, 75, 79, 83 16SB3...................................................................................106 243 BBC..................................................................................98
260199...........................................................67, 71, 75, 79, 83 16SE3...................................................................................107 244 BBC..................................................................................98
260201...........................................................67, 71, 75, 79, 83 16SF3...................................................................................107 246 BBC..................................................................................98

Indices
248ALCFP.............................................................................119 32SN2M63...........................................................................108 50SF4...................................................................................107

250JCS82.............................................................................111 32SP.....................................................................................108 50SP.....................................................................................108
250JCS92.............................................................................111 32SS.....................................................................................110 51 BBMS................................................................................99
250SF7.................................................................................107 355JCS82.............................................................................111 560JCS92.............................................................................111
250SG7.................................................................................107 355JCS92.............................................................................111 560SH9.................................................................................108
25LS.....................................................................................110 355SF8.................................................................................108 5PCB.......................................................................................95
25SA2...................................................................................106 355SH8.................................................................................108 6 BBCL....................................................................................99
25SB3...................................................................................106 35SB4...................................................................................106 6 SCHF..................................................................................112
25SE3...................................................................................107 3PCB.......................................................................................95 60 CSB....................................................................................95
25SF3...................................................................................107 4 BBCL....................................................................................99 60 CSBA ................................................................................95
25SN2..................................................................................108 400 FSCS................................................................................98 600MEB................................................................................101
25SP.....................................................................................108 400JCS82.............................................................................111 602XTNC..............................................................................103
25SS.....................................................................................110 400JCS92.............................................................................111 603GNC..................................................................................94
60AXEBSP............................................................................101 400SF8.................................................................................108 603GNL..................................................................................94
260KXEBSP..........................................................................101 400SF8M500........................................................................108 604GC.....................................................................................94
28ADS1X..............................................................................116 400SH8.................................................................................108 604R.....................................................................................108
28ADS2X..............................................................................116 402GCEBSP............................................................................97 604RL...................................................................................108
28ADSA1X...........................................................................116 403GNC..................................................................................94 604XTNC..............................................................................103
28ADSA2X...........................................................................116 403GNL..................................................................................94 606XTNC..............................................................................103
28ADSM1X..........................................................................116 404GC.....................................................................................94 608XTNC..............................................................................103
28ARD1X..............................................................................116 404R.....................................................................................108 60AXD2................................................................................100
28ARD2X..............................................................................116 405 APL..................................................................................96 60AXTN2..............................................................................100
28SDA2X18..........................................................................117 406 APL..................................................................................96 60CSBA..................................................................................95
28SDA3X25..........................................................................117 40SB4...................................................................................106 60KXDC2F............................................................................100
2LS.......................................................................................110 40SD5...................................................................................106 60KXSC2F.............................................................................100
2PCB.......................................................................................95 40SE4...................................................................................107 60KXTNC2F..........................................................................100
2SA2.....................................................................................106 40SF4...................................................................................107 61 BBMS................................................................................99
2SB3.....................................................................................106 40SP.....................................................................................108 61GNC....................................................................................94
2SE3.....................................................................................107 41 BBMS................................................................................99 630JCS92.............................................................................111
2SF3.....................................................................................107 428ALCDP............................................................................119 630SH9.................................................................................108
2SN2....................................................................................108 428ALCDPR..........................................................................119 630SY9.................................................................................108
2SS.......................................................................................110 428ALCFP.............................................................................119 637 APL..................................................................................96
3 BBCL....................................................................................99 428ALCFPR...........................................................................119 639 APL..................................................................................96
3 SCHF..................................................................................112 428ALCSPN..........................................................................119 63CFF....................................................................................113
303GNC..................................................................................94 428ALCSPNR........................................................................119 63CFFW................................................................................113
304GC.....................................................................................94 442 BBC..................................................................................98 63CMFB................................................................................112
304R.....................................................................................108 443 BBC..................................................................................98 63GNC....................................................................................94
304RL...................................................................................108 444 BBC..................................................................................98 63GNL....................................................................................94
304XSNC..............................................................................103 446 BBC..................................................................................98 63JCS82...............................................................................111
304XTNC..............................................................................103 448ALCFP.............................................................................119 63JCS92...............................................................................111
306XSNC..............................................................................103 450JCS92.............................................................................111 63MFA..................................................................................112
306XTNC..............................................................................103 450SH9.................................................................................108 63MFB..................................................................................112
308XSNC..............................................................................103 450SY9.................................................................................108 63MFC..................................................................................112
308XTNC..............................................................................103 454R.....................................................................................108 63MFD..................................................................................113
30AXD2................................................................................100 48ADS1X..............................................................................116 63SB4...................................................................................106
30AXTN2..............................................................................100 48ADS2X..............................................................................116 63SB4M100.........................................................................106
30KXDC2F............................................................................100 48ADSA1X...........................................................................116 63SB4M80...........................................................................106
30KXSC2F.............................................................................100 48ADSA2X...........................................................................116 63SD5...................................................................................106
30KXTNC2F..........................................................................100 48ADSM1X..........................................................................116 63SE4...................................................................................107
31 BBMS................................................................................99 48ARD1X..............................................................................116 63SE4M100..........................................................................107
310XTNC..............................................................................103 48ARD2X..............................................................................116 63SE4M80............................................................................107
312XSNC..............................................................................103 48SDA2X18..........................................................................117 63SF4...................................................................................107
312XTNC..............................................................................103 48SDA3X25..........................................................................117 63SF4M100..........................................................................107
315JCS82.............................................................................111 4LS.......................................................................................110 63SF4M80............................................................................107
315SF7.................................................................................107 4PCB.......................................................................................95 63SP.....................................................................................108
315SF7M400........................................................................107 4SA2.....................................................................................106 643 BBC..................................................................................98
315SG7.................................................................................107 4SB3.....................................................................................106 644 BBC..................................................................................98
32CFF....................................................................................113 4SE3.....................................................................................107 646 BBC..................................................................................98
32CFFW................................................................................113 4SF3.....................................................................................107 64GC.......................................................................................94
32CMFB................................................................................112 4SN2....................................................................................108 6LS.......................................................................................110
32LS.....................................................................................110 4SS.......................................................................................110 6SA2.....................................................................................106
32MFA..................................................................................112 5 BBCL....................................................................................99 6SB3.....................................................................................106
32MFB..................................................................................112 50 CSB....................................................................................95 6SE3.....................................................................................107
32MFD..................................................................................113 50 CSBA ................................................................................95 6SF3.....................................................................................107
32SA2...................................................................................106 500JCS92.............................................................................111 6SN2....................................................................................108
32SA2M40...........................................................................106 500SH9.................................................................................108 6SS.......................................................................................110
32SA2M50...........................................................................106 500SY9.................................................................................108 70CSB ....................................................................................95
32SA2M63...........................................................................106 503GNC..................................................................................94 70CSBA .................................................................................95
32SB3...................................................................................106 504GC.....................................................................................94 710JCS92.............................................................................111
32SB3M40...........................................................................106 504R.....................................................................................108 710SH10...............................................................................108
32SB3M50...........................................................................106 505 APL..................................................................................96 710SY10...............................................................................108
32SB3M63...........................................................................106 506 APL..................................................................................96 757 APL..................................................................................96
32SD5...................................................................................106 507 APL..................................................................................96 759 APL..................................................................................96
32SE3...................................................................................107 509 APL..................................................................................96 800 FSCS................................................................................98
32SF3...................................................................................107 50CSBA..................................................................................95 800JCS92.............................................................................111
32SN2..................................................................................108 50SB4...................................................................................106 800SH10...............................................................................108
32SN2M40...........................................................................108 50SD5...................................................................................106 800SY10...............................................................................108
32SN2M50...........................................................................108 50SE4...................................................................................107 802GCC..................................................................................96

Indices
803GNC..................................................................................94 EAM13...................................................................................32 EBMMPSL250........................................................................36

803GNL..................................................................................94 EAM16...................................................................................32 EBMMPSL250M.....................................................................36
804GC.....................................................................................94 EAM162H...............................................................................48 EBMNE8.................................................................................40
804R.....................................................................................108 EAM162V...............................................................................48 EBMP121................................................................................42
804RL...................................................................................108 EAM252H...............................................................................48 EBMP122................................................................................42
80JCS82...............................................................................111 EAM252L................................................................................48 EBMP182................................................................................42
80JCS92...............................................................................111 EAM252M..............................................................................48 EBMP242................................................................................42
80SD5...................................................................................106 EAM4.....................................................................................32 EBMP41..................................................................................42
80SF5...................................................................................107 EAM402H...............................................................................48 EBMP61..................................................................................42
80SO.....................................................................................106 EAM402L................................................................................48 EBMP81..................................................................................42
81 BBL....................................................................................98 EAM402M..............................................................................48 EBMR100.........................................................................35, 42
82 BBSK.................................................................................99 EAM404H...............................................................................48 EBMR30...........................................................................35, 42
843 BBC..................................................................................98 EAM404L................................................................................48 EBMR300.........................................................................35, 42
844 BBC..................................................................................98 EAM404M..............................................................................48 EBMR300T.......................................................................35, 42
846 BBC..................................................................................98 EAM632H...............................................................................48 EBMS1251N.....................................................................35, 42
8TT104.................................................................................117 EAM632M..............................................................................48 EBMS1253.......................................................................35, 42
8TT104SD.............................................................................117 EAM634H...............................................................................48 EBMS1253N.....................................................................35, 42
8TT87...................................................................................117 EAM634L................................................................................48 EBMS25...........................................................................36, 43
8TT88...................................................................................117 EAM634M..............................................................................48 EBMS2503.............................................................................36
8TT89...................................................................................117 EAM7.....................................................................................32 EBMSL1082MPMB................................................................36
8TT90...................................................................................117 EAM802H...............................................................................48 EBMSL14102MPMB..............................................................36
8TT90SD...............................................................................117 EAM802L................................................................................48 EBMSL642MPMB..................................................................36
8TT91...................................................................................117 EAM802M..............................................................................48 EBMSL862MPMB..................................................................36
8TT91SD...............................................................................117 EAM804H...............................................................................48 EBMTK...................................................................................40
8TT92...................................................................................117 EAM804L................................................................................48 EBMXDC15.............................................................................41
8TT92SD...............................................................................117 EAM804M..............................................................................48 EBMXDC18.............................................................................41
8TT93...................................................................................117 EAM9M..................................................................................32 EBMXDC30.............................................................................41
8TT93SD...............................................................................117 EAM9MB................................................................................32 EBMXDC45.............................................................................41
8TT94...................................................................................117 EAMBT1002.....................................................................32, 42 EBMXDC6...............................................................................41
8TT94SD...............................................................................117 EAMCK...................................................................................34 EBMXDC9...............................................................................41
8TT98...................................................................................117 EAME11.................................................................................34 EBMXDCG15..........................................................................41
8TT98SD...............................................................................117 EAME5...................................................................................34 EBMXE15...............................................................................41
90 CSB ...................................................................................95 EAMMP65..............................................................................32 EBMXPC1...............................................................................40
90 CSBA ................................................................................95 EAMP10.................................................................................42 EBMXPC2...............................................................................40
90CSBA..................................................................................96 EAMP13.................................................................................42 EM3SSK1T2...........................................................................32
9LD.......................................................................................103 EAMP16.................................................................................42 EM3SSK3T12.........................................................................36
ASALMSN..............................................................................51 EAMP4...................................................................................42 EM3SSK3T2...........................................................................36
ASAUXSN..............................................................................51 EAMP7...................................................................................42 EM96BP..........................................................69, 73, 77, 81, 85
ASPDL........................................................................34, 40, 51 EAMS100HE.....................................................................32, 42 EMABP.......................................................................34, 40, 41
ASPDL27..........................................................................40, 51 EAMS100LE.....................................................................32, 42 EMBH101...................................................................33, 37, 46
ASSNTSN110.........................................................................51 EAMS100ME....................................................................32, 42 EMBH101N............................................................................46
ASSNTSN415.........................................................................51 EAMS1251N....................................................................32, 42 EMBH102...................................................................33, 37, 46
ASUVRSC230.........................................................................51 EAMSL66M............................................................................32 EMBH102N............................................................................46
CR2002230.............................................................................61 EAMSL66MB..........................................................................32 EMBH104...................................................................33, 37, 46
CR2002230A..........................................................................61 EAMSL93M............................................................................32 EMBH104N............................................................................46
CR2011230.............................................................................61 EAMSL93MB..........................................................................32 EMBH106...................................................................33, 37, 46
CR2011230A..........................................................................61 EBK105SP...............................................................................97 EMBH106N............................................................................46
CR2020230.............................................................................61 EBK110SP...............................................................................97 EMBH106R100C.....................................................................49
CR2020230A..........................................................................61 EBK113SP...............................................................................97 EMBH106R10C.......................................................................49
CR2504230.............................................................................61 EBLB1.....................................................................................40 EMBH106R30C...........................................................33, 38, 49
CR2504230A..........................................................................61 EBLB2.....................................................................................40 EMBH108...................................................................33, 37, 46
CR2522230.............................................................................61 EBM121..................................................................................35 EMBH108N............................................................................46
CR2522230A..........................................................................61 EBM121D...............................................................................35 EMBH110...................................................................33, 37, 46
CR2530230.............................................................................61 EBM122..................................................................................35 EMBH110N............................................................................46
CR2530230A..........................................................................61 EBM122H...............................................................................35 EMBH110R100C.....................................................................49
CR2540230.............................................................................61 EBM161..................................................................................35 EMBH110R10C.......................................................................49
CR2540230A..........................................................................61 EBM182..................................................................................35 EMBH110R30C...........................................................33, 38, 49
CR4002230.............................................................................61 EBM182H...............................................................................35 EMBH113...................................................................33, 37, 46
CR4020230.............................................................................61 EBM22H.................................................................................35 EMBH113N............................................................................46
CR4030230.............................................................................61 EBM242..................................................................................35 EMBH116...................................................................33, 37, 46
CR4040230.............................................................................61 EBM242H...............................................................................35 EMBH116N............................................................................46
CR6320230.............................................................................62 EBM41....................................................................................35 EMBH116R100C.....................................................................49
CR6340230.............................................................................62 EBM61....................................................................................35 EMBH116R10C.......................................................................49
CRA611..................................................................................62 EBM62H.................................................................................35 EMBH116R30C...........................................................33, 38, 49
CRA620..................................................................................62 EBM81....................................................................................35 EMBH120...................................................................33, 37, 46
CRM2020230A.......................................................................62 EBM82H.................................................................................35 EMBH120N............................................................................46
CRM2540230A.......................................................................62 EBMBT2503.........................................................35, 36, 42, 43 EMBH120R100C.....................................................................49
CV1109SP.............................................................................101 EBMCC1253...........................................................................35 EMBH120R10C.......................................................................49
EAM10...................................................................................32 EBMGP4.................................................................................40 EMBH120R30C...........................................................33, 38, 49
EAM1002H.............................................................................48 EBMMB160......................................................................36, 43 EMBH125...................................................................33, 37, 46
EAM1002L..............................................................................48 EBMMB200......................................................................36, 43 EMBH125N............................................................................46
EAM1002M............................................................................48 EBMMB250......................................................................36, 43 EMBH132...................................................................33, 37, 46
EAM1004H.............................................................................48 EBMMPCT250........................................................................36 EMBH132N............................................................................46
EAM1004L..............................................................................48 EBMMPCT250M....................................................................36 EMBH132R100C.....................................................................49
EAM1004LT............................................................................48 EBMMPCT250MID.................................................................36 EMBH132R10C.......................................................................49
EAM1004M............................................................................48 EBMMPDC120.......................................................................36 EMBH132R30C...........................................................33, 38, 49
EAM12M................................................................................32 EBMMPSL125........................................................................36 EMBH140...................................................................33, 37, 46
EAM12MB..............................................................................32 EBMMPSL125M.....................................................................36 EMBH140N............................................................................46

Indices
EMBH140R30C...........................................................33, 38, 49 EMCH108N............................................................................46 EMCS120.........................................................................37, 47

EMBH145R30C...........................................................33, 38, 49 EMCH110...................................................................33, 37, 46 EMCS132.........................................................................37, 47
EMBH150...................................................................33, 37, 46 EMCH110N............................................................................46 EMCS140.........................................................................37, 47
EMBH150N............................................................................46 EMCH110R100C.....................................................................49 EMCS150.........................................................................37, 47
EMBH163...................................................................33, 37, 46 EMCH110R10C.......................................................................49 EMCS163.........................................................................37, 47
EMBH163N............................................................................46 EMCH110R30C...........................................................33, 38, 49 EMCS180.........................................................................37, 47
EMBH201...............................................................................46 EMCH113...................................................................33, 37, 46 EMCS3100.......................................................................38, 47
EMBH202...............................................................................46 EMCH113N............................................................................46 EMCS3125.......................................................................38, 47
EMBH204...............................................................................46 EMCH116...................................................................33, 37, 46 EMCS320.........................................................................38, 47
EMBH206...............................................................................46 EMCH116N............................................................................46 EMCS332.........................................................................38, 47
EMBH208...............................................................................46 EMCH116R100C.....................................................................49 EMCS340.........................................................................38, 47
EMBH210...............................................................................46 EMCH116R10C.......................................................................49 EMCS350.........................................................................38, 47
EMBH213...............................................................................46 EMCH116R30C...........................................................33, 38, 49 EMCS363.........................................................................38, 47
EMBH216...............................................................................46 EMCH120...................................................................33, 37, 46 EMCS380.........................................................................38, 47
EMBH220...............................................................................46 EMCH120N............................................................................46 EMDH101...................................................................33, 37, 46
EMBH225...............................................................................46 EMCH120R100C.....................................................................49 EMDH101N............................................................................46
EMBH232...............................................................................46 EMCH120R10C.......................................................................49 EMDH102...................................................................33, 37, 46
EMBH240...............................................................................46 EMCH120R30C...........................................................33, 38, 49 EMDH102N............................................................................46
EMBH250...............................................................................46 EMCH125...................................................................33, 37, 46 EMDH104...................................................................33, 37, 46
EMBH263...............................................................................46 EMCH125N............................................................................46 EMDH104N............................................................................46
EMBH301.........................................................................37, 47 EMCH125R30C...........................................................33, 38, 49 EMDH106...................................................................33, 37, 46
EMBH302.........................................................................37, 47 EMCH132...................................................................33, 37, 46 EMDH106N............................................................................46
EMBH304.........................................................................37, 47 EMCH132N............................................................................46 EMDH108...................................................................33, 37, 46
EMBH306.........................................................................37, 47 EMCH132R100C.....................................................................49 EMDH108N............................................................................46
EMBH308.........................................................................37, 47 EMCH132R10C.......................................................................49 EMDH110...................................................................33, 37, 46
EMBH310.........................................................................37, 47 EMCH132R30C...........................................................33, 38, 49 EMDH110N............................................................................46
EMBH313.........................................................................37, 47 EMCH140...................................................................33, 37, 46 EMDH113...................................................................33, 37, 46
EMBH316.........................................................................37, 47 EMCH140N............................................................................46 EMDH113N............................................................................46
EMBH320.........................................................................37, 47 EMCH140R30C...........................................................33, 38, 49 EMDH116...................................................................33, 37, 46
EMBH325.........................................................................37, 47 EMCH145R30C...........................................................33, 38, 49 EMDH116N............................................................................46
EMBH332.........................................................................37, 47 EMCH150...................................................................33, 37, 46 EMDH120...................................................................33, 37, 46
EMBH340.........................................................................37, 47 EMCH150N............................................................................46 EMDH120N............................................................................46
EMBH350.........................................................................37, 47 EMCH163...................................................................33, 37, 46 EMDH125...................................................................33, 37, 46
EMBH363.........................................................................37, 47 EMCH163N............................................................................46 EMDH125N............................................................................46
EMBH401...............................................................................47 EMCH201...............................................................................46 EMDH132...................................................................33, 37, 46
EMBH402...............................................................................47 EMCH202...............................................................................46 EMDH132N............................................................................46
EMBH404...............................................................................47 EMCH204...............................................................................46 EMDH140...................................................................33, 37, 46
EMBH406...............................................................................47 EMCH206...............................................................................46 EMDH140N............................................................................46
EMBH408...............................................................................47 EMCH208...............................................................................46 EMDH150...................................................................33, 37, 46
EMBH410...............................................................................47 EMCH210...............................................................................46 EMDH150N............................................................................46
EMBH413...............................................................................47 EMCH213...............................................................................46 EMDH163...................................................................33, 37, 46
EMBH416...............................................................................47 EMCH216...............................................................................46 EMDH163N............................................................................46
EMBH420...............................................................................47 EMCH220...............................................................................46 EMDH201...............................................................................46
EMBH425...............................................................................47 EMCH225...............................................................................46 EMDH202...............................................................................46
EMBH432...............................................................................47 EMCH232...............................................................................46 EMDH204...............................................................................46
EMBH440...............................................................................47 EMCH240...............................................................................46 EMDH206...............................................................................46
EMBH450...............................................................................47 EMCH250...............................................................................46 EMDH208...............................................................................46
EMBH463...............................................................................47 EMCH263...............................................................................46 EMDH210...............................................................................46
EMBP................................................................................34, 40 EMCH301.........................................................................37, 47 EMDH213...............................................................................46
EMBPH...................................................................................40 EMCH302.........................................................................37, 47 EMDH216...............................................................................46
EMBS1100.......................................................................37, 47 EMCH304.........................................................................37, 47 EMDH220...............................................................................46
EMBS1125.......................................................................37, 47 EMCH306.........................................................................37, 47 EMDH225...............................................................................46
EMBS120.........................................................................37, 47 EMCH308.........................................................................37, 47 EMDH232...............................................................................46
EMBS132.........................................................................37, 47 EMCH310.........................................................................37, 47 EMDH240...............................................................................46
EMBS140.........................................................................37, 47 EMCH313.........................................................................37, 47 EMDH250...............................................................................46
EMBS150.........................................................................37, 47 EMCH316.........................................................................37, 47 EMDH263...............................................................................46
EMBS163.........................................................................37, 47 EMCH320.........................................................................37, 47 EMDH301.........................................................................37, 47
EMBS180.........................................................................37, 47 EMCH325.........................................................................37, 47 EMDH302.........................................................................37, 47
EMBS3100.......................................................................38, 47 EMCH332.........................................................................37, 47 EMDH304.........................................................................37, 47
EMBS3125.......................................................................38, 47 EMCH340.........................................................................37, 47 EMDH306.........................................................................37, 47
EMBS320.........................................................................38, 47 EMCH350.........................................................................37, 47 EMDH308.........................................................................37, 47
EMBS332.........................................................................38, 47 EMCH363.........................................................................37, 47 EMDH310.........................................................................37, 47
EMBS340.........................................................................38, 47 EMCH401...............................................................................47 EMDH313.........................................................................37, 47
EMBS350.........................................................................38, 47 EMCH402...............................................................................47 EMDH316.........................................................................37, 47
EMBS363.........................................................................38, 47 EMCH404...............................................................................47 EMDH320.........................................................................37, 47
EMBS380.........................................................................38, 47 EMCH406...............................................................................47 EMDH325.........................................................................37, 47
EMCH101...................................................................33, 37, 46 EMCH408...............................................................................47 EMDH332.........................................................................37, 47
EMCH101N............................................................................46 EMCH410...............................................................................47 EMDH340.........................................................................37, 47
EMCH102...................................................................33, 37, 46 EMCH413...............................................................................47 EMDH350.........................................................................37, 47
EMCH102N............................................................................46 EMCH416...............................................................................47 EMDH363.........................................................................37, 47
EMCH104...................................................................33, 37, 46 EMCH420...............................................................................47 EMDH401...............................................................................47
EMCH104N............................................................................46 EMCH425...............................................................................47 EMDH402...............................................................................47
EMCH106...................................................................33, 37, 46 EMCH432...............................................................................47 EMDH404...............................................................................47
EMCH106N............................................................................46 EMCH440...............................................................................47 EMDH406...............................................................................47
EMCH106R100C.....................................................................49 EMCH450...............................................................................47 EMDH408...............................................................................47
EMCH106R10C.......................................................................49 EMCH463...............................................................................47 EMDH410...............................................................................47
EMCH106R30C...........................................................33, 38, 49 EMCS1100.......................................................................37, 47 EMDH413...............................................................................47
EMCH108...................................................................33, 37, 46 EMCS1125.......................................................................37, 47 EMDH416...............................................................................47

Indices
EMDH420...............................................................................47 EPBN1SUPM....................................................................68, 69 MC150M3MDT....................................................................123

EMDH425...............................................................................47 EPBN21240............................................................................74 MC150M3S..........................................................................122
EMDH432...............................................................................47 EPBN21240SXB......................................................................76 MC150M3SDT.....................................................................123
EMDH440...............................................................................47 EPBN21240SXM..............................................................73, 77 MC175M4............................................................................122
EMDH450...............................................................................47 EPBN21263............................................................................78 MC175M4DT........................................................................123
EMDH463...............................................................................47 EPBN21263SXB................................................................79, 84 MC175M4M.........................................................................122
EMDL..........................................................................34, 40, 41 EPBN21263SXM..............................................................81, 85 MC175M4MDT....................................................................123
EMDS1100.......................................................................37, 47 EPBN21840............................................................................74 MC175M4S..........................................................................122
EMDS120.........................................................................37, 47 EPBN21840SXB......................................................................76 MC175M4SDT.....................................................................123
EMDS132.........................................................................37, 47 EPBN21840SXM....................................................................77 MC200M4............................................................................122
EMDS140.........................................................................37, 47 EPBN21863............................................................................78 MC200M4DT........................................................................123
EMDS150.........................................................................37, 47 EPBN21863SXB................................................................79, 84 MC200M4M.........................................................................122
EMDS163.........................................................................37, 47 EPBN21863SXM..............................................................81, 85 MC200M4MDT....................................................................123
EMDS180.........................................................................37, 47 EPBN2640..............................................................................74 MC200M4S..........................................................................122
EMDS3100.......................................................................38, 47 EPBN2640SXB..................................................................71, 76 MC200M4SDT.....................................................................123
EMDS320.........................................................................38, 47 EPBN2640SXM................................................................73, 77 MC225M5............................................................................122
EMDS332.........................................................................38, 47 EPBN2863..............................................................................78 MC225M5DT........................................................................123
EMDS340.........................................................................38, 47 EPBN2BP3..................................................................75, 79, 83 MC225M5M.........................................................................122
EMDS350.........................................................................38, 47 EPBN2CX250........................................................72, 76, 80, 84 MC225M5MDT....................................................................123
EMDS363.........................................................................38, 47 EPBN2EX250....................................................................72, 76 MC225M5S..........................................................................122
EMDS380.........................................................................38, 47 EPBN2EX250M.................................................................72, 76 MC225M5SDT.....................................................................123
EMGP142...............................................................................40 EPBN2EXDIN..............................................................72, 76, 84 MC250M5............................................................................122
EMPL..........................................................................34, 40, 41 EPBN31280............................................................................82 MC250M5DT........................................................................123
EPBCTMT160.................................................69, 73, 77, 81, 85 EPBN3880..............................................................................82 MC250M5M.........................................................................122
EPBCTMT250.......................................................73, 77, 81, 85 EPBN3BP3..............................................................................83 MC250M5MDT....................................................................123
EPBCTMT3P...................................................69, 73, 77, 81, 85 EPBN3EX250....................................................................80, 84 MC250M5S..........................................................................122
EPBCTMT400.........................................................................85 EPBN3EX250M.................................................................80, 84 MC250M5SDT.....................................................................123
EPBDLK1...........................................................................71, 75 EPBN3EXDIN..........................................................................80 MC25M1..............................................................................122
EPBKEL250.............................................................................69 EPBN3LKKTM.................................................69, 73, 77, 81, 85 MC25M1M...........................................................................122
EPBKEL400.......................................................................73, 77 EPBN3LKRJ45................................................69, 73, 77, 81, 85 MC25M1S............................................................................122
EPBKEL800.......................................................................81, 85 EPBN3SUPM................................72, 73, 76, 77, 80, 81, 84, 85 MC275M6............................................................................122
EPBKN1253............................................................................67 EPBPN11225..........................................................................91 MC275M6DT........................................................................123
EPBKN1253M.........................................................................67 EPBPN11240..........................................................................91 MC275M6M.........................................................................122
EPBKN1254............................................................................67 EPBPN1425............................................................................91 MC275M6MDT....................................................................123
EPBKN1254M.........................................................................67 EPBPN1625............................................................................91 MC275M6S..........................................................................122
EPBKN125L............................................................................67 EPBPN1640............................................................................91 MC275M6SDT.....................................................................123
EPBKN125LM.........................................................................67 EPBPN1825............................................................................91 MC300M6............................................................................122
EPBKN2403......................................................................71, 75 EPBPN21240..........................................................................91 MC300M6DT........................................................................123
EPBKN2403M...................................................................71, 75 EPBPN21263..........................................................................91 MC300M6M.........................................................................122
EPBKN2404......................................................................71, 75 EPBPN21840..........................................................................91 MC300M6MDT....................................................................123
EPBKN2404M...................................................................71, 75 EPBPN21863..........................................................................91 MC300M6S..........................................................................122
EPBKN240L......................................................................71, 75 EPBPN2640............................................................................91 MC300M6SDT.....................................................................123
EPBKN240LM...................................................................71, 75 EPBPN2863............................................................................91 MC325M7DT........................................................................123
EPBKN2633............................................................................78 EPBPN31280..........................................................................91 MC325M7MDT....................................................................123
EPBKN2633M.........................................................................78 EPBPN3880............................................................................91 MC325M7SDT.....................................................................123
EPBKN2634............................................................................78 EPBSXBCTMT.................................................69, 73, 77, 81, 85 MC350M7DT........................................................................123
EPBKN2634M.........................................................................78 ETM2209SP..........................................................................104 MC350M7MDT....................................................................123
EPBKN263L............................................................................78 ETM2210SP..........................................................................104 MC350M7SDT.....................................................................123
EPBKN263LM.........................................................................78 ETM2211SP..........................................................................104 MC375M8DT........................................................................123
EPBKN3803............................................................................82 ETM2212SP..........................................................................104 MC375M8MDT....................................................................123
EPBKN3803M.........................................................................82 ETM2223SP..........................................................................104 MC375M8SDT.....................................................................123
EPBKN3804............................................................................82 ETM2224SP..........................................................................104 MC400M8DT........................................................................123
EPBKN3804M.........................................................................82 ETM2225SP..........................................................................104 MC400M8MDT....................................................................123
EPBKTFSLW......................................................................78, 82 ETM2226SP..........................................................................104 MC400M8SDT.....................................................................123
EPBKTFSN2............................................................................67 M21MSSU...........................................................................118 MC425M9DT........................................................................123
EPBKTFSN3............................................................................71 M21MSU..............................................................................118 MC425M9MDT....................................................................123
EPBMETER1.....................68, 69, 72, 73, 76, 77, 80, 81, 84, 85 M21MSU2K.........................................................................118 MC450M9DT........................................................................123
EPBN11225............................................................................66 M21MSU2SK.......................................................................118 MC450M9MDT....................................................................123
EPBN11225SXB......................................................................67 M21MSULK..........................................................................118 MC475M10DT......................................................................123
EPBN11225SXM....................................................................69 M21MSUML........................................................................118 MC475M10MDT..................................................................123
EPBN11240............................................................................70 M22MSU..............................................................................118 MC500M10DT......................................................................123
EPBN1425..............................................................................66 M22MSUL............................................................................118 MC500M10MDT..................................................................123
EPBN1425SXB........................................................................67 M23MSUL............................................................................118 MC50M2..............................................................................122
EPBN1425SXM......................................................................69 MC100M2DT........................................................................123 MC50M2M...........................................................................122
EPBN1625..............................................................................66 MC100M2MDT....................................................................123 MC50M2S............................................................................122
EPBN1625SXB........................................................................67 MC100M2SDT.....................................................................123 MC525M11DT......................................................................123
EPBN1625SXM......................................................................69 MC100M4............................................................................122 MC525M11MDT..................................................................123
EPBN1640..............................................................................70 MC100M4M.........................................................................122 MC550M11DT......................................................................123
EPBN1825..............................................................................66 MC100M4S..........................................................................122 MC550M11MDT..................................................................123
EPBN1825SXB........................................................................67 MC125M3DT........................................................................123 MC575M12DT......................................................................123
EPBN1825SXM......................................................................69 MC125M3MDT....................................................................123 MC575M12MDT..................................................................123
EPBN1BP1......................................................67, 71, 75, 79, 83 MC125M3SDT.....................................................................123 MC600M12DT......................................................................123
EPBN1CX250..........................................................................68 MC125M5............................................................................122 MC600M12MDT..................................................................123
EPBN1EX250..........................................................................68 MC125M5M.........................................................................122 MC75M3..............................................................................122
EPBN1EX250M.......................................................................68 MC125M5S..........................................................................122 MC75M3M...........................................................................122
EPBN1EXDIN..........................................................................68 MC150M3............................................................................122 MC75M3S............................................................................122
EPBN1SPD123................................................69, 73, 77, 81, 85 MC150M3DT........................................................................123 N2-250KCO............................................................................66
EPBN1SPD1234..............................................69, 73, 77, 81, 85 MC150M3M.........................................................................122 N2-4-250KCO.........................................................................66

Indices
N3-400...................................................................................70 PFR-03....................................................................................63
N3-4-400................................................................................70 PFR-5......................................................................................63
NLW-4-630.............................................................................78 PFR-W-105.............................................................................63
NLW-4-800.............................................................................82 PFR-W-140.............................................................................63
NLW-630................................................................................78 PFR-W-20...............................................................................63
NLW-800................................................................................82 PFR-W-210.............................................................................63
NZM1-1-XKSA...............................................67, 71, 75, 79, 83 PFR-W-30...............................................................................63
NZM1-XKSA...................................................67, 71, 75, 79, 83 PFR-W-35...............................................................................63
NZM2-XKSA...............................................................75, 79, 83 PFR-W-70...............................................................................63
NZMB1-1-AF100............................................67, 71, 75, 79, 83 SH265SP..............................................................................101
NZMB1-1-AF125............................................67, 71, 75, 79, 83 SH754SP..............................................................................101
NZMB1-1-AF16..............................................67, 71, 75, 79, 83 SNT4LP11K......................................................................79, 83
NZMB1-1-AF20..............................................67, 71, 75, 79, 83 TR-G3/8..................................................................................63
NZMB1-1-AF32..............................................67, 71, 75, 79, 83 UVH4LP11K......................................................................79, 83
NZMB1-1-AF40..............................................67, 71, 75, 79, 83 WA1212...............................................................................103
NZMB1-1-AF50..............................................67, 71, 75, 79, 83
NZMB1-1-AF63..............................................67, 71, 75, 79, 83
NZMB1-1-AF80..............................................67, 71, 75, 79, 83
NZMB1-A100.................................................67, 71, 75, 79, 83
NZMB1-A125.................................................67, 71, 75, 79, 83
NZMB1-A160.................................................67, 71, 75, 79, 83
NZMB1-A20...................................................67, 71, 75, 79, 83
NZMB1-A32...................................................67, 71, 75, 79, 83
NZMB1-A40...................................................67, 71, 75, 79, 83
NZMB1-A50...................................................67, 71, 75, 79, 83
NZMB1-A63...................................................67, 71, 75, 79, 83
NZMB1-A80...................................................67, 71, 75, 79, 83
NZMC1-A100.............................................................75, 79, 83
NZMC1-A125.............................................................75, 79, 83
NZMC1-A160.............................................................75, 79, 83
NZMC1-A20...............................................................75, 79, 83
NZMC1-A32...............................................................75, 79, 83
NZMC1-A40...............................................................75, 79, 83
NZMC1-A50...............................................................75, 79, 83
NZMC1-A63...............................................................75, 79, 83
NZMC1-A80...............................................................75, 79, 83
NZMC2-4-A160KCO...............................................................66
NZMC2-4-A200KCO...............................................................66
NZMC2-4-A250KCO...............................................................66
NZMC2-A125-BT........................................................75, 79, 83
NZMC2-A160-BT........................................................75, 79, 83
NZMC2-A160KCO..................................................................66
NZMC2-A200-BT........................................................75, 79, 83
NZMC2-A200KCO..................................................................66
NZMC2-A250-BT........................................................75, 79, 83
NZMC2-A250KCO..................................................................66
NZMLW-4-A630.....................................................................78
NZMLW-4-A800.....................................................................82
NZMLW-A630........................................................................78
NZMLW-A800........................................................................82
NZMN2-4-A160KCO..............................................................66
NZMN2-4-A200KCO..............................................................66
NZMN2-4-A250KCO..............................................................66
NZMN2-A125-BT.......................................................75, 79, 83
NZMN2-A160-BT.......................................................75, 79, 83
NZMN2-A160KCO..................................................................66
NZMN2-A200-BT.......................................................75, 79, 83
NZMN2-A200KCO..................................................................66
NZMN2-A250-BT.......................................................75, 79, 83
NZMN2-A250KCO..................................................................66
NZMN3-4-A250...............................................................70, 74
NZMN3-4-A320...............................................................70, 74
NZMN3-4-A400...............................................................70, 74
NZMN3-A250...................................................................70, 74
NZMN3-A250BT....................................................................83
NZMN3-A320...................................................................70, 74
NZMN3-A320BT....................................................................83
NZMN3-A400...................................................................70, 74
NZMN3-A400BT....................................................................83
OBK103SP..............................................................................97
OLV725SP.............................................................................101
OLV726SP.............................................................................101
OLV727SP.............................................................................101
OLV728SP.............................................................................101
PD1...............................................................34, 40, 41, 97, 103
PD2.............................................................................34, 40, 51
PD4.......................................................................................101
PFR-003..................................................................................63

At Eaton, were energized by the challenge of powering a world
that demands more. With over 100 years experience in electrical
power management, we have the expertise to see beyond today.
From groundbreaking products to turnkey design and engineering
services, critical industries around the globe count on Eaton.
We power businesses with reliable, efficient and safe electrical

power management solutions. Combined with our personal
service, support and bold thinking, we are answering tomorrows
needs today. Follow the charge with Eaton.
Visit eaton.com/electrical.
Eaton Electric Limited

Grimshaw Lane
Middleton
Manchester M24 1GQ
United Kingdom
Customer Support Centre
Tel: +44 (0)8700 545 333
Fax: +44 (0)8700 540 333
email: [email protected]
2015 Eaton Corporation

All Rights Reserved
Printed in UK
Form No. PG01414001U
March 2015 www.eaton.uk.com/electrical

Kumar

Uploaded by

Copyright:

Available Formats

Kumar

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Kumar

Uploaded by

Copyright:

Available Formats

MCB Distribution boards Enclosed motor, heating

and enclosures and lighting control

Smart solutions for

2 Memshield 3 MCB distribution boards and enclosures 31

3 Distribution board switch and protection devices 45

4 Modular control and switching devices 53

5 Memshield 3 MCCB panelboards 65

6 Industrial switch & fusegear 93

7 HRC cartridge fuselinks & fuse units 105

8 Enclosed motor, heating and lighting control 115

9 Power factor correction capacitors 121

10 Technical data 125

Eatons comprehensive range of power distribution

1.1 TYPE A, SPN 125A DISTRIBUTION BOARDS AND PAN ASSEMBLIES.................................................................................... 6

1.2 TYPE B, TPN 125A/250A DISTRIBUTION BOARDS AND PAN ASSEMBLIES........................................................................... 8

1.3 TYPE B, TPN 250A DISTRIBUTION BOARDS........................................................................................................................... 10

1.4 DISTRIBUTION BOARD METERING SOLUTIONS................................................................................................................... 12

1.5 DISTRIBUTION BOARD SWITCH AND PROTECTION DEVICES............................................................................................. 13

1.6 MODULAR CONTROL AND SWITCHING DEVICES................................................................................................................. 14

1.7 MCCB PANELBOARDS AND PAN ASSEMBLIES...................................................................................................................... 15

1.8 SURGE PROTECTION DEVICES................................................................................................................................................ 16

1.9 INDUSTRIAL SWITCH & FUSEGEAR........................................................................................................................................ 17

Glasgow fuse-switch-disconnectors & switch-disconnectors...................................................................................................... 17

Glasgow busbar chamber system................................................................................................................................................ 18

Exel 2 switch-disconnectors & switch-disconnector fuses........................................................................................................... 19

Rotary isolators and changeover switches.................................................................................................................................. 20

Exel distribution fuseboards..................................................................................................................................................... 21

HRC cartridge fuselinks, carriers and bases................................................................................................................................ 22

1.10 ENCLOSED MOTOR, HEATING AND LIGHTING CONTROL.................................................................................................... 24

1.11 POWER FACTOR CORRECTION CAPACITORS......................................................................................................................... 26

POWER DISTRIBUTION COMPONENTS PG01414001U March 2015 5

Twist action handle, with optional

Hinged doors provide 180

Removable gland plates are provided

High quality clear sub circuit

Cover screwed by means of

Dual rated MCBs 10/15kA to New 125A Switch Disconnector

Features & benefits General characteristics

6 POWER DISTRIBUTION COMPONENTS PG01414001U March 2015

Easy access earth bar can

Unique full form blanking

Type A SPN distribution boards Incoming devices

POWER DISTRIBUTION COMPONENTS PG01414001U March 2015 7

Removable gland plates are provided

IP4X robust steel enclosure to suit

Twist action access handle, with optional

Cable trunking Existing case end screws

Removable front door to aid

Secondary cover slides over two

Features & benefits

8 POWER DISTRIBUTION COMPONENTS PG01414001U March 2015

Increased width of board to 440mm

Dual rated MCBs 10/15kA to IEC 60898

Unique full form blanking

125A incomer kits available as

Reversed Earth & Neutral bar

Type B SPN pan assemblies Improved neutral box clamp

POWER DISTRIBUTION COMPONENTS PG01414001U March 2015 9

Type B, TPN 250A distribution board solutions

MCB Distribution boards Enclosed motor, heating