CD-RECEIVER

KDC-W3041
KDC-W312
KDC-W241
KDC-241
INSTRUCTION MANUAL

B64-3903-10/01 (EW/E2W)

B64-3903-10_01_EW_En.indd 1 07.7.25 2:41:12 PM

 Contents

Before use 3 Appendix 12

Basic Operation 4 Accessories/ Installation Procedure 14
General functions
Tuner functions Connecting Wires to Terminals 15
Disc play functions
Installation/Removing the Unit 17
General Operation 6
Audio Control Troubleshooting Guide 18
Audio Setup
Speaker Setting Specifications 19
Switching Display
Tuner Operation 8
PTY (Program Type)
Program Type preset
Changing Language for PTY Function
Music disc/Audio file Operation 9
Folder Select
Menu Operation 10
Menu System
Manual Clock Adjustment
Auxiliary Input Display Setting
Demonstration mode Setting

2 | KDC-W3041/KDC-W312/KDC-W241/KDC-241

B64-3903-00_00_E_En.indd 2 07.7.11 1:46:35 PM

 Before use

2WARNING If you experience problems during installation,

consult your Kenwood dealer.
To prevent injury or fire, take the following
When you purchase optional accessories, check with
precautions:
your Kenwood dealer to make sure that they work
To prevent a short circuit, never put or leave any
with your model and in your area.
metallic objects (such as coins or metal tools) inside
the unit. The characters which can be displayed by this unit
are A-Z 0-9 @ " ` % & * + = , . / \ < > [ ] ( ) : ; ^ - { } |
~.
Before using this unit for the first time The RDS feature wont work where the service is not
This unit is initially set on the Demonstration mode. supported by any broadcasting station.
When using this unit for the first time, cancel the The illustrations of the display and the panel
<Demonstration mode Setting> (page 11). appearing in this manual are examples used to
explain more clearly how the controls are used.
How to reset your unit Therefore, what appears on the display in the
If the unit fails to operate properly, press the Reset illustrations may differ from what appears on the
button. The unit returns to factory settings when the display on the actual equipment, and some of the
Reset button is pressed. illustrations on the display may be inapplicable.
Press the reset button if the disc auto changer fails
to operate correctly. Normal operation should be Handling CDs
restored. Do not touch the recording surface of the CD.
Do not stick tape etc. on the CD, or use a CD with
tape stuck on it.
Do not use disc type accessories.
Clean from the center of the disc and move
outward.
When removing CDs from this unit, pull them out
Reset button horizontally.
Cleaning the Unit If the CD center hole or outside rim has burrs,
If the faceplate of this unit is stained, wipe it with a use the CD only after removing the burrs with a
dry soft cloth such as a silicon cloth. ballpoint pen etc.
If the faceplate is stained badly, wipe the stain off with
a cloth moistened with neutral cleaner, then wipe it CDs that cannot be used
again with a clean soft dry cloth. CDs that are not round cannot be used.

Applying spray cleaner directly to the unit may affect its
mechanical parts. Wiping the faceplate with a hard cloth or
using a volatile liquid such as thinner or alcohol may scratch
the surface or erases characters.

CDs with coloring on the recording surface or CDs

Cleaning the Faceplate Terminals that are dirty cannot be used.
If the terminals on the unit or faceplate get dirty, wipe
them with a clean soft dry cloth. This unit can only play the CDs with
.
This unit may not correctly play discs which do not
have the mark.
Lens Fogging
When you turn on the car heater in cold weather, You cannot play a CD-R or CD-RW that has not been
dew or condensation may form on the lens in the finalized. (For the finalization process refer to your
CD player of the unit. Called lens fogging, this CD-R/CD-RW writing software, and your CD-R/CD-
condensation on the lens may not allow CDs to play. RW recorder instruction manual.)
In such a situation, remove the disc and wait for the
condensation to evaporate. If the unit still does not
operate normally after a while, consult your Kenwood
dealer.

English | 3

B64-3903-00_00_E_En.indd 3 07.7.11 1:46:35 PM

 Basic Operation
Release Display Disc slot Control [ ] Auxiliary input
knob

[VOL] [SRC] [1] [2] [3] [4] [5] [6] [TI]/[AUTO] [B.BOOST]

General functions Auxiliary input Auxiliary input

Connect a portable audio device with mini-plug cable
Power/Source select button [SRC] (3.5 ).
Turns on the power.
When the power is on, the source switches between

Use the mini-plug cable which is stereo type and does not
Tuner (TUNER) , CD (CD) , Auxiliary input (AUX),
have any resistance.
and Standby (STANDBY) each time this button is
pressed. Muting volume upon reception of phone call
Press at least 1 second to turn off the power. When there is a call, CALL is displayed and the audio
system is paused.
Volume control [VOL] When the call ends, CALL disappears and the audio
system comes back on.
Bass boost [B.BOOST] The audio system comes back on when [SRC] is
Switches between Boost 1 (BB-L L1), Boost 2 (BB-L
pressed during a call.
L2), and Boost off (BB-L OFF) each time this button
is pressed. Subwoofer output (KDC-W3041/KDC-W312)

Faceplate release Release Control knob

Releases the faceplate lock so that it can be removed. Switches between ON (SW ON) and OFF (SW OFF)
Refer to the following diagram when reattaching the each time the bottom side is pressed for at least 2
faceplate. seconds.
Text/Title scroll (KDC-W3041/KDC-W312/
KDC-W241) Control knob
Scrolls the CD, audio file, and Radio text display when
pressing the top side for at least 2 seconds.

The faceplate is a precision piece of equipment and can be
damaged by shocks or jolts.
Keep the faceplate in its faceplate case while detached.
Do not place the faceplate (and the faceplate case) in areas
exposed to direct sunlight, excessive heat or humidity. Also
avoid places with too much dust or the possibility of water
splashing.
To prevent deterioration, do not touch the terminals of the
unit or faceplate with your fingers.

4 | KDC-W3041/KDC-W312/KDC-W241/KDC-241

B64-3903-00_00_E_En.indd 4 07.7.11 1:46:38 PM

 : Indicates the button etc. to operate.

Tuner functions Disc play functions

Band select Control knob Disc play Disc slot

Switches between FM1, FM2, and FM3 each time the Starts playing when a disc is inserted.
top side is pressed. When a CD is inserted, the IN indicator is ON.
Switches to AM when the bottom side is pressed.

Tuning Control knob 3 inch CD cannot be used. Attempt to insert using an
Changes the frequency when the left or right side is adapter can cause malfunction.
pressed. Refer to <About Audio file> (page 12) for the Audio file by
models you can play.

During reception of stereo stations the ST indicator is ON.
Pause and play Control knob
Switches between pause and play each time the
Traffic information (KDC-W3041/KDC-W312/ center is pressed.
KDC-241) [TI]
Disc ejection [0]
Turns ON or OFF the Traffic Information function.
When the function is turned ON, TI indicator is ON.
If traffic bulletin starts when the function is ON, You can eject the disc for 10 minutes after switching off the
TRAFFIC is displayed and traffic information is engine.
received. Music search Control knob
Changes the music when the left or right side is
pressed.
If the volume is adjusted during reception of traffic
information, the adjusted volume is memorized Fast reverses or forwards the music while pressing the
automatically. The memorized volume will be applied next left or right side.
time the Traffic Information function is turned ON.
Folder search (KDC-W3041/KDC-W312/KDC-W241)
Tuning mode select (KDC-W241) [AUTO] Control knob
Switches the Tuning mode each time this button Changes the folder containing the audio file when the
is pressed. Refer to AUTO1, AUTO2, MANUAL of top or bottom side is pressed.
<Appendix> (page 12).
Track/ File/ Folder repeat play [4]
Preset memory [1] - [6] Switches between Track Repeat (TRAC REP) and OFF
Memorize the station selected when pressing for at
(REP OFF) when pressed while playing a CD.
least 2 seconds.
Switches between File Repeat (FILE REP), Folder
Auto memory entry [TI]/ [AUTO] Repeat (FOLD REP), and OFF (REP OFF) when
Memorizes six stations with good reception pressed while playing an audio file.
automatically when pressed for at least 2 seconds.
Scan play [2]
Preset tuning [1] - [6] Successively plays the intro of the music in the disc or
Recalls the memorized station. folder.
TRAC SCN/ FILE SCN is displayed during Scan Play.

Random play [3]

Randomly plays the music in the disc or folder.
DISC RDM/ FOLD RDM is displayed during Random
Play.

English | 5

B64-3903-00_00_E_En.indd 5 07.7.11 1:46:41 PM

 General Operation

Audio Control
Volume offset: Sets each sources volume as a difference
1 Select the source to adjust from the basic volume.
Press the [SRC] button.
4 Adjust the Audio setup item
2 Enter Audio Control mode Turn the [VOL] knob.
Press the [VOL] knob.
5 Exit Audio Setup mode
3 Select the Audio item to adjust Press the [VOL] knob for at least 1 second.
Press the [VOL] knob.
Adjustment Item Display Range
Subwoofer level* SW L 15 +15
System Q NATURAL/ Natural/Rock/Pops/Easy/Top Speaker Setting
ROCK/POPS/ 40/Jazz/User setting Fine-tuning so that the System Q value is optimal
EASY/TOP40/
JAZZ/USER when setting the speaker type.
Bass level BAS L 8 +8
1 Enter Standby
Middle level MID L 8 +8
Press the [SRC] button.
Treble level TRE L 8 +8
Select the STANDBY display.
Balance BAL Left 15 Right 15
Fader FAD Rear 15 Front 15 2 Enter Speaker Setting mode
Exit Audio Control mode (Volume control mode) Press the [VOL] knob.
*Function of KDC-W3041/W312. 3 Select the Speaker type
Turn the [VOL] knob.
USER: This appears when Bass level, Middle level, and Speaker type Display
Treble level are adjusted. When USER is selected, OFF SP OFF
these levels are recalled. For 5 & 4 in. speaker SP 5/4
4 Adjust the Audio item For 6 & 6x9 in. speaker SP 6*9/6
Turn the [VOL] knob. For the OEM speaker SP OEM

5 Exit Audio Control mode 4 Exit Speaker Setting mode

Press any button. Press the [VOL] knob.
Press a button other than the [VOL] knob.

Switching Display
Audio Setup
Changing the information displayed.
Setting the Sound system.
1 Enter Switching Display mode
1 Select the source to adjust Press the center of the Control knob for at least
Press the [SRC] button. 1 second.
2 Enter Audio Setup mode DISP SEL is displayed.
Press the [VOL] knob for at least 1 second. 2 Select the Display item
3 Select the Audio Setup item to adjust Press the right or left side of the Control knob.
Press the [VOL] knob. In Tuner source
Adjustment Item Display Range Information Display
Low Pass Filter* LPF 80/120/160/Through Hz Program Service name or Frequency FREQ/ FREQ/PS
Volume offset V-OFF 8 0 (AUX: -8 +8) Radio text, Program Service name or Frequency* R-TEXT
*Function of KDC-W3041/W312. Clock CLOCK
* This is not displayed on the KDC-W241/KDC-241.

6 | KDC-W3041/KDC-W312/KDC-W241/KDC-241

B64-3903-00_00_E_En.indd 6 07.7.11 1:46:42 PM

 In CD source
Information Display
Disc title* D-TITLE
Track title* T-TITLE
Play time & Track number P-TIME
Clock CLOCK
* This is not displayed on the KDC-241.

In Audio file source

Information Display
Music title & Artist name TITLE
Album name & Artist name ALBUM
Folder name FOLDER
File name FILE
Play time & Music number P-TIME
Clock CLOCK

In Standby/ Auxiliary input source

Information Display
Source name SRC NAME
Clock CLOCK

3 Exit Switching Display mode

Press the center of the Control knob.

When you select the clock display, the display setting of
each source will be changed to the clock display.
Album name cannot be displayed in WMA file.
If the selected display item does not have any
information, alternative information is displayed.

English | 7

B64-3903-00_00_E_En.indd 7 07.7.11 1:46:43 PM

 Function of KDC-W3041/KDC-W312/KDC-241
Tuner Operation

PTY (Program Type) Speech: No.3 11, 18 25, 31

Selecting the Program Type and searching for a 3 Search for the selected Program Type station
station. Press the right or left side of the Control knob.

1 Enter PTY mode When the selected Program Type is not found, NO PTY
Press the center of the Control knob. is displayed. Select another Program Type.
During PTY mode the PTY indicator is ON.
4 Exit PTY mode
Press the center of the Control knob.
This function cannot be used during a traffic bulletin or
AM reception.

2 Select the Program Type

Press the top or bottom side of the Control Program Type preset
knob. Putting the Program Type in the Preset button
No. Program Type Display memory and quick recall.
1. Speech SPEECH
Presetting the Program Type
2. Music MUSIC
3. News NEWS 1 Select the Program Type to preset
4. Current Affairs AFFAIRS Refer to <PTY (Program Type)>.
5. Information INFO 2 Preset the Program Type
6. Sport SPORT Press the desired [1] [6] button for at least 2
7. Education EDUCATE seconds.
8. Drama DRAMA
9. Culture CULTURE Recalling the preset Program Type
10. Science SCIENCE 1 Enter PTY mode
11. Varied VARIED Refer to <PTY (Program Type)>.
12. Pop Music POP M
13. Rock Music ROCK M 2 Recall the Program Type
14. Easy Listening Music EASY M Press the desired [1] [6] button.
15. Light Classical LIGHT M
16. Serious Classical CLASSICS
17. Other Music OTHER M
18. Weather WEATHER
Changing Language for PTY Function
19. Finance FINANCE Selecting the Program Type display language.
20. Childrens programs CHILDREN
21. Social Affairs SOCIAL 1 Enter PTY mode
22. Religion RELIGION Refer to <PTY (Program Type)>.
23. Phone In PHONE IN 2 Enter Changing Language mode
24. Travel TRAVEL Press the [TI] button.
25. Leisure LEISURE
26. Jazz Music JAZZ
3 Select the language
Press the top or bottom side of the Control
27. Country Music COUNTRY
knob.
28. National Music NATION M
29. Oldies Music OLDIES Language Display
30. Folk Music FOLK M English ENGLISH
31. Documentary DOCUMENT French FRENCH
German GERMAN

Speech and Music include the Program type shown 4 Exit Changing Language mode
below. Press the center of the Control knob.
Music: No.12 17, 26 30

8 | KDC-W3041/KDC-W312/KDC-W241/KDC-241

B64-3903-00_00_E_En.indd 8 07.7.11 1:46:43 PM

 Music disc/Audio file Operation

Function of KDC-W3041/KDC-W312/KDC-W241
Function of Audio file
Folder Select
Quickly selecting the folder you want to hear.

1 Enter Folder Select mode

Press the [5] button.
FLD SEL is displayed.
Displays the current folder name.
2 Select the folder
Operation type Operation
Movement between folders Press the right or left side of the Control
knob.
Selection of folder Press the top side of the Control knob.
Return to previous folder Press the bottom side of the Control knob.
Return to root folder Press the [3] button.

3 Decide the folder to play

Press the center of the Control knob.
Cancelling the Folder Select mode
Press the [5] button.

English | 9

B64-3903-00_00_E_En.indd 9 07.7.11 1:46:43 PM

 Menu Operation

Menu System Display Setting Setting overview Source

Setting various functions. AUX OFF/ON1*/ Sets whether to display AUX
ON2 during source selection.
1 Enter Menu mode OFF OFF 60M Turns off the power when the
Press the [B.BOOST] button for at least 1 preset time has lapsed in the
second. Standby mode.
MENU is displayed. CD READ*2 1*/2 Sets the CD read mode.
DEMO Refer to Specifies whether to enable
2 Select the menu item page 11 demonstration.
Press the top or bottom side of the Control
knob. * Factory setting
Display Setting Setting overview Source *1 This is not displayed on the KDC-W241.
*2 This is not displayed on the KDC-241.
CLK ADJ Refer to Sets the clock. *3 Function of Russian sales model.
page 10
: Can be set in standby state.
SYNC*1 ON*/OFF Synchronizing the RDS station : Can be set in other than standby state.
time data and this units clock. : Can be set while Audio file source.
DIM ON/OFF* Adjusts the brightness of : Can be set while Tuner source.
the display according to the : Can be set during FM reception.
surrounding illumination. : Can be set while accessing AUX source.
SWPRE*1*2 R*/ SW Sets the preout output.
SPRM*2 ON*/OFF Turns ON/OFF the Supreme Refer to the respective page for information on how to
function. set the items with reference page number.
NEWS*1 OFF* Turns ON/OFF the News Bulletin Refer to the <Appendix> (page 12) for the details of the
90M Automatic Reception function menu items.
and sets the news bulletin
interrupt disabled time. 3 Set the menu item
LO.S ON/OFF* Only stations whose reception is Press the right or left side of the Control knob.
good are searched in auto seek 4 Exit Menu mode
tuning.
Press the [B.BOOST] button.
AUTO1/ AUTO1*/ Selects the tuning mode of
AUTO2/ AUTO2/ the radio.
MANU*1 MANU
AF*1 ON*/OFF When station reception is poor,
automatically switches to the Manual Clock Adjustment
station that is broadcasting the
same program over the same RDS 1 Select Clock Adjustment mode
network. Press the top or bottom side of the Control
REG*1 ON*/OFF Sets whether to switch to the knob.
station only in the specific region Select the CLK ADJ display.
using the AF control.
2 Enter Clock Adjust mode
ATPS*1 ON*/OFF When traffic information station
Press the center of the Control knob for at least
reception is poor, automatically
searches for a station that can be 1 second.
received better. The clock display blinks.
MONO ON/OFF* Receives a stereo broadcast in the 3 Adjust the hours
mono mode. Press the top or bottom side of the Control
NAME SET Refer to Sets the display when switched knob.
page 11 to AUX source.
RUS*3 ON*/OFF Selects Russian as the display Adjust the minutes
language. Press the right or left side of the Control knob.
SCL*2 AUTO/ Specifies whether the text is 4 Exit Clock adjustment mode
MANU* scrolled automatically. Press the [B.BOOST] button.

10 | KDC-W3041/KDC-W312/KDC-W241/KDC-241

B64-3903-00_00_E_En.indd 10 07.7.11 1:46:43 PM

 Demonstration mode Setting
You can do this adjustment when the SYNC is set as Sets the demonstration mode.
OFF.
1 Select the Demonstration mode
Press the top or bottom side of the Control
knob.
Auxiliary Input Display Setting Select the DEMO display.

Selecting the display when changing to Auxiliary 2 Set the Demonstration mode
input source. Press the center of the Control knob for at least
2 seconds.
1 Select Auxiliary input source Each time you press the knob at least 2 seconds,
Press the [SRC] button. the Demonstration mode alternates between the
Select the AUX display. settings shown in the table below.
2 Enter Menu mode Display Setting
Press the [B.BOOST] button for at least 1 DEMO ON The Demonstration mode function is ON.
second. DEMO OFF Exit Demonstration mode (Normal mode).
MENU is displayed.
3 Select Auxiliary input display setting mode
Press the top or bottom side of the Control
knob.
Select the NAME SET display.
4 Enter Auxiliary input display setting mode
Press the center of the Control knob for at least
1 second.
The presently selected Auxiliary input display is
displayed.
5 Select the Auxiliary input display
Press the right or left side of the Control knob.
Each time you push the knob, the display alternates
as listed below.
AUX
DVD
PORTABLE
GAME
VIDEO
TV
6 Exit Auxiliary input display setting mode
Press the [B.BOOST] button.

When operation stops for 10 seconds, the name at that
time is registered, and the Auxiliary input display setting
mode closes.

English | 11

B64-3903-00_00_E_En.indd 11 07.7.11 1:46:44 PM

 Appendix

About Audio file Menu Glossary

Playable Model SWPRE (Switching Preout)
KDC-W3041, KDC-W312, KDC-W241 Switches the preout between rear output (R) and
Playable Audio file subwoofer output (SW).
MP3 (.mp3), WMA (.wma) SPRM (Supreme)
Playable disc media Technology to extrapolate and supplement with
CD-R/RW/ROM proprietary algorithm, the high-frequency range
that is cut off when encoding at low bit rate.
Playable disc file format
Supplementing is optimized by compression
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.
format (MP3 or WMA) and processed according to
Although the audio files are complied with the bit rate.
standards listed above, the play maybe impossible The effect is negligible with music that is encoded
depending on the types or conditions of media or at high bit rate, variable bit rate or has minimal high
device. frequency range.
Playing order of the Audio file CD READ
In the example of folder/file tree shown below, the Sets the method for reading CD.
files are played in the order from to . When unable to play special format CD, set this
CD () <: Folder
Folder function to 2 to force playing. Note that some
v : Audio
Audiofile
fi music CD may be unplayable even when set to 2.
v

In addition, audio files cannot be played when set

 to 2. Normally, keep this set to 1.
v 1 : Automatically distinguishes between audio file
v disc and music CD when playing disc.
 2 : Forces playing as music CD.
v
AUX

v When this is set to ON, AUX source can be selected.
ON1: Outputs the sound of external unit connected
v. to the AUX terminal when switched to AUX
An online manual about audio files is put on the source.
site, www.kenwood.com/audiofile/. On this online ON2: Activates the attenuator function when
manual, detailed information and notes which are not switched to AUX source.
written in this manual are provided. Make sure to read Turn off the attenuator function when
through the online manual as well. listening to output from external unit. This
prevents the noise when no external unit is
connected to AUX terminal.
OFF: Disables the selection of AUX source.
Set to OFF when not using the AUX terminal.
NEWS (News Bulletin with Timeout Setting)
Automatically receives news bulletin when it
starts. Set the time during which interrupt is to be
disabled after start of another news bulletin.
Changing NEWS 00M to NEWS 90M turns this
function ON. When this function is ON, the NEWS
indicator is ON.
If news bulletin starts when this function is ON,
TRAFFIC is displayed and news is received. If 20M
is has been set, reception of another news bulletin
will not start for 20 minutes.

12 | KDC-W3041/KDC-W312/KDC-W241/KDC-241

B64-3903-00_00_E_En.indd 12 07.7.11 1:46:44 PM

 AUTO1, AUTO2, MANUAL (Tuning mode select) This Product is not installed by the manufacturer of a
Select a tuning mode of the radio. vehicle on the production line, nor by the professional
Tuning mode Display Operation importer of a vehicle into an EU Member State.
Auto seek AUTO 1Automatic search for a station.
Preset station seek AUTO 2Search in order of the stations in the Information on Disposal of Old Electrical
Preset memory. and Electronic Equipment (applicable for
Manual MANUAL Normal manual tuning control. EU countries that have adopted separate
waste collection systems)
AF (Alternative Frequency)
When the reception is poor, automatically alternate Products with the symbol (crossed-out
to another frequency broadcasting the same wheeled bin) cannot be disposed as
program in the same RDS network with better household waste.
reception. Old electrical and electronic equipment
should be recycled at a facility capable
RUS (Russian language setting)
of handling these items and their waste
When this is set to ON, the following character
byproducts. Contact your local authority
strings are displayed in Russian:
for details in locating a recycle facility
Folder name/ File name/ Song title/ Artist name/
nearest to you. Proper recycling and waste
Album name/ CD text (internal CD source)
disposal will help conserve resources whilst
preventing detrimental effects on our
health and the environment.

The marking of products using lasers

(Except for some areas)
OFF (Power OFF Timer)
Setting the timer to turn this units power OFF CLASS 1
automatically when Standby mode continues.
Using this setting can save the vehicles battery LASER PRODUCT
power.
The label is attached to the chassis/case and says
: Power OFF Timer function is OFF.
that the component uses laser beams that have been
20M: Turns the power OFF after 20 minutes.
classified as Class 1. It means that the unit is utilizing
(Factory setting)
laser beams that are of a weaker class. There is no
40M: Turns the power OFF after 40 minutes.
danger of hazardous radiation outside the unit.
60M: Turns the power OFF after 60 minutes.

English | 13

B64-3903-00_00_E_En.indd 13 07.7.11 1:46:45 PM

 Accessories/ Installation Procedure

Accessories with the ignition, connect the ignition wire to a power

source that can be turned on and off with the ignition key.
Use a commercially available conversion connector if the
1 connector does not fit in the vehicle connector.
Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
..........1 on the ends of the unconnected wires or the terminals.
If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
2 If the fuse blows, first make sure the wires arent touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
..........2 Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
Installation Procedure part in the car.
After the unit is installed, check whether the brake lamps,
1. To prevent short circuits, remove the key from the blinkers, wipers, etc. on the car are working properly.
ignition and disconnect the - terminal of the Mount the unit so that the mounting angle is 30 or less.
battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the wire on the wiring harness.
4. Take Connector B on the wiring harness and
connect it to the speaker connector in your vehicle.
5. Take Connector A on the wiring harness and
connect it to the external power connector on your
vehicle.
6. Connect the wiring harness connector to the unit.
7. Install the unit in your car.
8. Reconnect the - terminal of the battery.
9. Press the reset button.

Mounting and wiring this product requires skills and
experience. For safetys sake, leave the mounting and wiring
work to professionals.
Make sure to ground the unit to a negative 12V DC power
supply.
Do not install the unit in a spot exposed to direct sunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
If the power is not turned ON (PROTECT is displayed),
the speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
Make sure that all wire connections are securely made by
inserting jacks until they lock completely.
If your vehicles ignition does not have an ACC position, or
if the ignition wire is connected to a power source with
constant voltage such as a battery wire, the power will not
be linked with the ignition (i.e., it will not turn on and off
along with the ignition). If you want to link the units power

14 | KDC-W3041/KDC-W312/KDC-W241/KDC-241

B64-3903-00_00_E_En.indd 14 07.7.11 1:46:49 PM

 Connecting Wires to Terminals

Rear preput/ Subwoofer preput

(KDC-W3041/KDC-W312 only)
Fuse (10A)

FM/AM antenna input

Antenna Cord (JASO)

Wiring harness
(Accessory1)

TEL mute wire (Brown) Connect to the terminal that is grounded when
MUTE
either the telephone rings or during conversation.
To connect the Kenwood navigation system,
consult your navigation manual.

If no connections are made, do

not let the wire come out from
the tab.
Power control/ Motor
antenna control wire
(Blue/White) Connect either to the power control terminal
P.CONT when using the optional power amplifier, or to the
ANT.CONT antenna control terminal in the vehicle.
Battery wire (Yellow)
Ignition wire (Red)

See next page.

A7 Pin (Red)
A4 Pin (Yellow)

8 6 4 2 Connector A
7 5 3 1
8 6 4 2 Connector B
7 5 3 1

English | 15

B64-3903-00_00_E_En.indd 15 07.7.11 1:46:49 PM

 Connecting Wires to Terminals

Connector Function Guide 2WARNING

Pin Numbers for Cable Colour Functions Connecting the ISO Connector
ISO Connectors The pin arrangement for the ISO connectors depends on
External Power the type of vehicle you drive. Make sure to make the proper
Connector connections to prevent damage to the unit.
A-4 Yellow Battery
The default connection for the wiring harness is described in
A-5 Blue/White Power Control
1 below. If the ISO connector pins are set as described in 2
A-7 Red Ignition (ACC)
or 3, make the connection as illustrated.
A-8 Black Earth (Ground)
Please be sure to reconnect the cable as shown 2 below to
Connection
install this unit to the Volkswagen vehicles etc.
Speaker
Connector
B-1 Purple Rear Right (+) 1 (Default setting) The A-7 pin (red) of the vehicles
B-2 Purple/Black Rear Right () ISO connector is linked with the ignition, and the A-
B-3 Gray Front Right (+) 4 pin (yellow) is connected to the constant power
B-4 Gray/Black Front Right () supply.
B-5 White Front Left (+) Ignition cable (Red) A-7 Pin (Red)
B-6 White/Black Front Left ()
B-7 Green Rear Left (+) Unit Vehicle
B-8 Green/Black Rear Left ()
Battery cable (Yellow) A-4 Pin (Yellow)
2 The A-7 pin (red) of the vehicles ISO connector is
connected to the constant power supply, and the
A-4 pin (yellow) is linked to the ignition.
Ignition cable
(Red) A-7 Pin (Red)

Unit Vehicle

Battery cable A-4 Pin (Yellow)

(Yellow)
3 The A-4 pin (yellow) of the vehicles ISO connector
is not connected to anything, while the A-7 pin
(red) is connected to the constant power supply
(or both the A-7 (red) and A-4 (yellow) pins are
connected to the constant power supply).
Ignition cable (Red) A-7 Pin (Red)

Unit Vehicle

Battery cable (Yellow) A-4 Pin (Yellow)

When the connection is made as in 3 above, the units
power will not be linked to the ignition key. For that reason,
always make sure to turn off the units power when the
ignition is turned off.
To link the units power to the ignition, connect the ignition
cable (ACC...red) to a power source that can be turned on
and off with the ignition key.

16 | KDC-W3041/KDC-W312/KDC-W241/KDC-241

B64-3903-00_00_E_En.indd 16 07.7.11 1:46:50 PM

 Installation/Removing the Unit

Installation Removing the hard rubber frame

Metal mounting strap 1 Engage the catch pins on the removal tool and
(commercially available)
remove the two locks on the upper level.
Firewall or metal support Upper the frame and pull it forward as shown in
the figure.

Lock
Catch

Bend the tabs of the

Accessory2
mounting sleeve with a Removal tool
screwdriver or similar utensil
and attach it in place. 2 When the upper level is removed, remove the
Self-tapping screw
lower two locations.
(commercially available)
Screw (M4X8) The frame can be removed from the bottom side in the
(commercially available) same manner.

Removing the Unit

Make sure that the unit is installed securely in place. If the
unit is unstable, it may malfunction (for example, the sound 1 Refer to the section <Removing the hard rubber
may skip). frame> and then remove the hard rubber frame.
2 Remove the screw (M4 8) on the back panel.
3 Insert the two removal tools deeply into the slots
on each side, as shown.
4 Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.
Screw (M4X8)
(commercially available)
Accessory2

Be careful to avoid injury from the catch pins on the
removal tool.
5 Pull the unit all the way out with your hands, being
careful not to drop it.

English | 17

B64-3903-00_00_E_En.indd 17 07.7.11 1:46:50 PM

 Troubleshooting Guide

Some functions of this unit may be disabled by The messages shown below display your
some settings made on this unit. systems condition.
TOC ERR: No disc has been loaded in the disc
! Cannot display the user of System Q. magazine.
<Audio Control> (page 6) is not set. The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
! Cannot set up the subwoofer.
No output from the subwoofer. E-05: The disc is unreadable.
Cannot set up the low pass filter.
E-15: Media was played that doesnt have data
Preout is not set to subwoofer. <Menu System>
recorded that the unit can play.
(page 10)
<Subwoofer output> (page 4) is not set to On. E-77: The unit is malfunctioning for some reason.
Press the reset button on the unit. If the E-
! Cannot set up Display. 77 code does not disappear, consult your
<Demonstration mode Setting> (page 11) is not nearest service center.
turned off.
E-99: Something is wrong with the disc magazine.
Or the unit is malfunctioning for some reason.
Check the disc magazine. And then press
What might seem to be a malfunction in your unit the reset button on the unit. If the E-99
may just be the result of slight misoperation or code does not disappear, consult your
nearest service center.
miswiring. Before calling service, first check the
following table for possible problems. IN (Blink): The CD player section is not operating
properly.
Tuner source Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
? Radio reception is poor. even when the CD has been properly
The car antenna is not extended. reinserted, please switch off the power
Pull the antenna out all the way. and consult your nearest service center.

Disc source PROTECT: The speaker wire has a short-circuit or

touches the chassis of the vehicle, and then
? The specified disc does not play, but another one the protection function is activated.
plays instead. Wire or insulate the speaker cable
The specified CD is quite dirty. properly and press the reset button. If
Clean the CD. the PROTECT code does not disappear,
The disc is loaded in a different slot from that consult your nearest service center.
specified.
Eject the disc magazine and check the number NA FILE: An Audio file is played with a format that this
for the specified disc. unit cant support.
The disc is severely scratched. ----
Try another disc instead.
COPY PRO: A copy-protected file is played.
----
Audio file source
? The sound skips when an Audio file is being
played.
The media is scratched or dirty.
Clean the media, referring to the CD cleaning of
the section on <Handling CDs> (page 3).
The recording condition is bad.
Record the media again or use another media.

18 | KDC-W3041/KDC-W312/KDC-W241/KDC-241

B64-3903-00_00_E_En.indd 18 07.7.11 1:46:51 PM

 Specifications

FM tuner section Audio section

Frequency range (50 kHz space) Maximum output power
: 87.5 MHz 108.0 MHz KDC-W3041/W312/W241 : 50 W x 4
Usable sensitivity (S/N = 26dB) KDC-241 : 45 W x 4
: 0.7 V/75 Full Bandwidth Power (at less than 1% THD)
Quieting Sensitivity (S/N = 46dB) KDC-W3041/W312/W241 : 30 W x 4
: 1.6 V/75 KDC-241 : 28 W x 4
Frequency response (3.0 dB) Speaker Impedance
: 30 Hz 15 kHz :48
Signal to Noise ratio (MONO) Tone action
: 65 dB Bass : 100 Hz 8 dB
Selectivity (DIN) (400 kHz) Middle : 1 kHz 8 dB
: 80 dB Treble : 10 kHz 8 dB
Stereo separation (1 kHz) Preout level / Load (CD) (KDC-W3041/W312)
: 35 dB : 2000 mV/10 k
Preout impedance (KDC-W3041/W312)
MW tuner section : 600
Frequency range (9 kHz space)
: 531 kHz 1611 kHz Auxiliary input
Usable sensitivity (S/N = 20dB) Frequency response (3 dB)
: 25 V : 20 Hz 20 kHz
Input Maximum Voltage
LW tuner section : 1200 mV
Frequency range Input Impedance
: 153 kHz 281 kHz : 100 k
Usable sensitivity (S/N = 20dB)
: 45 V General
Operating voltage (11 16V allowable)
CD player section : 14.4 V
Laser diode Current consumption
: GaAlAs : 10 A
Digital filter (D/A) Installation Size (W x H x D)
: 8 Times Over Sampling : 182 x 53 x 155 mm
D/A Converter Weight
: 1 Bit : 1.30 kg
Spindle speed
: 500 200 rpm (CLV)
Wow & Flutter
: Below Measurable Limit
Frequency response (1 dB)
: 20 Hz 20 kHz
Total harmonic distortion (1 kHz)
: 0.01 %
Signal to Noise ratio (1 kHz)
KDC-W3041/W312/W241 : 105 dB
KDC-241 : 93 dB
Dynamic range
: 93 dB
MP3 decode (KDC-W3041/W312/W241)
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode (KDC-W3041/W312/W241)
: Compliant with Windows Media Audio

Specifications subject to change without notice.

English | 19

B64-3903-00_00_E_En.indd 19 07.7.11 1:46:51 PM

 Declaration of Conformity with regard to the EMC Directive 2004/108/EC
Manufacturer:
Kenwood Corporation
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan
EU Representative's:
Kenwood Electronics Europe BV
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands

B64-3903-10_01_EW_En.indd 20 07.7.25 2:41:13 PM