Lap Dat Cau Unic

INSTALLATION MANUAL
UNIC HYDRAULIC CRANE

FOR MARINE USE
MODEL
SERIES
UBA260 series
UBA340 series
UBA500 series
HEAD OFFICE : Center Bldg., 3-12, Higashishinagawa 2-chome,

Shinagawa-ku, Tokyo 140-0002, JAPAN
IMUBA200605A
PRINTED IN JAPAN
TABLE OF CONTENTS
1. GENERAL VIEW ......................1- 1 9. OVERALL VIEW OF CRANES

q UBA263 (3-section boom) ......................9- 1
2. CRANE INTTALLATION GUIDE w UBA264 (4-section boom)..........................9- 2
q Position of instalation ..............................2- 1 e UBA343 (3-section boom) .......................9- 3
w Dimensions of crane base for instalation ...2- 1 r UBA344 (4-section boom) ......................9- 4
e Base for mounting crane ..........................2- 2 t UBA345 (5-section boom) ......................9- 5
r [Optional] Round-shaped base .................2- 3 y UBA503 (3-section boom) ......................9- 6
t Storage of boom and hook .......................2- 5 u UBA504 (4-section boom) ......................9- 7
i UBA505 (5-section boom) ......................9- 8
3. SELECTION OF PUMP AND
ELECTRIC MOTOR ................3- 1
4. SELECTION OF
OIL TANK ............4- 1
5. PIPING PROCEDURES
q Mounting of control valve .......................5- 1
w Hose connection ......................................5- 2
e Piping port connecting control valve .......5- 4
r Port connecting piping on the side ..........5- 5
t Hoses connecting to piping on
the bottom side .......5- 6
y Caution for piping ....................................5- 8
u How to check recommended allowable
back pressure of control valve .................5- 9
i Hydraulic circuit of crane ........................5-10
6.ZERO-POINT ADJUSTMENT
OF LOAD METER.......................6- 1
7.ATTACHMENT OF CHART OF
RATED LOAD STICKERS .....7- 1
8. RECOMMENDED
COMPONENTS
q Pump and electric motor ..........................8- 1
w [Optional] Hydraulic equipment .................8- 2
e [Optional] Components for piping between
control valve and crane body ..................8- 4
r [Optional] Mounting base for
control valves .......8- 5
t [Optional] Installation of radio/
reote controller ......8- 6
MEMO
1. GENERAL VIEW
Weight, distance from gravity center, and height of gravity center of UBA
series
Hoist winch (hoist motor with reduction gear)
Boom
L Anti-disengagement device
Column
W Over-winding
H h alarm device
Hook
Slewing Derricking cylinder

Base
Slewing reduction gear
Slewing motor
center Control lever

(For piping system
on the side)
Control valve
(For piping system on
the bottom side)
W (kg): L (mm): H (mm): h (mm):

Height to bottom of
Model Weight at gravity Distance to Height of gravity
anti-disengaging
center gravity center center device
UBA503 1040 685 1160 1280
UBA504 1220 875 1250 1290
UBA505 1330 950 1290 1290
UBA343 790 690 1080 1130
UBA344 935 885 1165 1120
UBA345 1010 960 1195 1120
UBA263 550 520 915 980
UBA264 695 740 1055 970
Prepare the components to be installed on the cane (mounting base, hydraulic unit,
hoses, and bolts) to mount them.
Weight of 15kg of control valves and related components does not include in the
weight illustrated in the table above.
Weight of the control valves and related components for the radio remote controller
is 45kg.
1-1
2. CRANE INTTALLATION GUIDE
q POSITION OF INSTALATION
When deciding where to install the crane, it is no doubt to decide it in considering the
most convenient operation of the crane, but in case of mounting it on a small vessel,
install it at the position where the least fluctuation of the trim (difference between the
head and the stern) and of lateral slanting (or at the center of the ship) will be expected
while sailing or operating the crane in particular.
w DIMENSIONS OF CRANE BASE FOR INSTALATION
C
D
b5
D
C
B
d

a3
b4
a2 b3
A a1 b2
B
b1 a5 a4
A
UBA 500 AND UBA340 SERIES UBA260 SERIES
(UNIT : mm)
Model A B C D Installation Bolt
M243.0 Equivalent to 10.9 12pcs

UBA500 SERIES 600 600 28 26
[Tightening torque: 275314N-m (28
(12 places)
32kgf-m)]
UBA340 SERIES 520 520 25 24
(12 places)
25kgf-m)]
UBA260 SERIES 460 460 22 24
(8 places)
25kgf-m)]
Model a1 a2 a3 a4 a5 b1 b2 b3 b4 b5 d
UBA500 SERIES 180 180 180 180 180 180 300
UBA340 SERIES 140 180 140 140 180 140 250
UBA260 SERIES 200 200 200 200 200
2-1
CRANE INSTALLATION GUIDE
e BASE FOR MOUNTING CRANE

1. Determine the height of mounting base so that it will not hit against the protrusions such as
of the bridge while slewing the crane.
* Pay attention that gravity center will not be too high when mounting it on a small vessel
to keep stability.
2. Junction of the mounting base to the hull is most important.
Examine strength by referring to the values illustrated below to secure sufficient strength.
(Since the values are calculated data, they should be referred as a yardstick.)
UBA260 UBA340 UBA500
Model Remarks
SERIES SERIES SERIES
Including weight of crane
Moment around slewing itself
center 54.9 88.3 133.4 Coefficient for dynamic
M=WR kNm {5600} {9000} {13600} load:1.25
[kgfm] Coefficient for static load
:1.10
Tensile side 42.2 44.1 58.8
Strength of kN [kgf] {4300} {4500} {6000} Load to be applied per
mounting
bolt
bolts Compressive 48.1 50.0 64.7
side kN [kgf] {4900} {5100} {6600}
3. When installing the crane on an inclined plane, allow the mounting surface of base to be
level first to install the crane..
4. Install both the crane base and the mounting base with mounting bolts.
Secure the mounting bolts by means of double-nut system or by application of locking
agent to prevent them from being loose.
5. Set up a drainage hole at the bottom of the mounting base to drain water.
If the drainage hole is impossible to be set up, instruct operators to drain water
periodically out of the drain plug in the crane base.
M
Drain plug
W
Mounting base
R
2-2
r [OPTION] ROUND-SHAPED BASE

When mounting the crane on a round-shaped mounting base, use a round base (spacer)
illustrated below.
UBA260 series UBA340 series
2, 3 2, 3
Base assembly Base assembly
t22
t22
170
170
t22
t22
Mounting bolts for fixing the round-shaped Mounting bolts for fixing the round-shaped
base are to be prepared by customer. base are to be prepared by customer.
Heat-treated bolt (equivalent to 10.9) Heat-treated bolt (equivalent to 10.9)
M18X80 (711918080) 16 pcs M18X80 (711918080) 18pcs
20 holes at 18 places equally drilled on the P.C.D.
5
D.44 .50
0
P.C.
460
.D
P.C
520
0
49

0
56

460
1
520 1
Note: Mounting dimensions of the Note: Mounting dimensions of the

round-shaped base are the round-shaped base are the
same as those of the old type same as those of the old type
ZF260MR series provided by T ZF300MR series provided by T
company. company.
Parts list Parts list
Mounting of round-shaped base Mounting of round-shaped base
Device number: 09E057000 Device number: 099857000
Item Part name Part number Q'ty Item Part name Part number Q'ty
1 Round base 09E057010 1 1 Round base 099857010 1
Heat-treated bolt Heat-treated bolt
2 711922D90 8 2 711922D90 12
(M2290L) (M2290L)
3 Nut 72111122D 16 3 Nut 72111122D 24
2-3
UBA500 series
2, 3
Base assembly
t25
185
t25
Mounting bolts for fixing the round-shaped
base are to be prepared by customer.
Heat-treated bolt (equivalent to 10.9)
M2090 (711920090) 18 pcs
80
.D.5
P.C
600
650

600
1
Note: Mounting dimensions of the
round-shaped base are the
same as those of the old type
ZF500MR series provided by T
company.
Parts list
Mounting of round-shaped base
Device number: 096C57000
Item Part name Part number Q'ty
1 Round base 096C57010 1
Heat-treated bolt
2 760129083 12
(M24100L)
3 Nut 72111124D 24
2-4
t STORAGE OF BOOM AND HOOK

Mount a boom rest and a hook catch for fixing the lifting hook to reduce impact to the crane
due to waves during sailing of the ship.
Boom rest
Hook catch
CAUTION
Mount the crane on a level surface to prevent it from being
tilted during crane operation.
2-5
3. SELECTION OF PUMP AND ELECTRIC MOTOR
Set up the hydraulic source by referring to the following table.
UBA500 UBA340 UBA260

Model
SERIES SERIES SERIES
kgf/cm2
Rated pressure MPa 19.6200 17.2175 17.2175
Rated flow l/min 60 60 53
Recommended pump
(1) For engines with accelerator
Theoretical delivery:cm3/rev 44 36 33
Max. revolution speed in use:min-1 1400 1700 1700
(Max. speed in use:rpm) (1400) (1700) (1700)
(Delivery:l/min) (60) (60) (53)
(2) For engines without accelerator
Max. revolution speed in use:min-1 1500 1500 1500
(Max. speed in use:rpm) (1500) (1500) (1500)
(Delivery:l/min) (40) (40) (35)
(3) For electric motor
50Hz area
Revolution speed in use:min-1 1450 1450 1450
(Revolution in use:rpm) (1450) (1450) (1450)
(Delivery:l/min)
(32) (32) (28)
60Hz area
Theoretical delivery:cm3/rev
Revolution speed in use:min-1 20 20 18
(Revolution in use:rpm) 1750 1750 1750
(Delivery:l/min) (1750) (1750) (1750)
(33) (33) (30)
Recommended electric motor

Sealed outer-fan type 15KW or over 15KW or over 11KW or over
AC200V 4-pole
3-1
SELECTION OF PUMP AND ELECTRIC MOTOR
CAUTION
Confirm rotating direction of the pump.
When hydraulic power is less than the rated pressure and
the rated flow of the crane, the rated crane operation may
not be carried out.
When hydraulic power is more than the rated flow of the
crane, adjust the hydraulic power to a level that is less
than the rated flow by flow control valve or the like.
In this case, set up a oil tank with sufficient capacity as the
oil temperature will be easy to rise.
3-2
4. SELECTION OF OIL TANK
1 Use a oil tank with sufficient capacity so that oil temperature will not rise over 80.
In normal crane operation, a tank with the capacity of 1.5 times as much as the rated
flow is needed.
Place the mounting base for the crane body at a position where it is level or higher
against the position of the oil tank.
2 Use an oil tank of open type.
3 Recommended filter:
Suction side: Filtration of 100-mesh.

Return side: Filtration of 10
4 Recommended hydraulic oil:
Use industrial-type hydraulic oil;

ISO VG 46 for most temperatures
ISO VG 32 extremely low temperatures
5 Allowable operating hydraulic oil temperature range for the crane is -15~80.
CAUTION
Oil tank of closed type allows the back pressure to be
generated in the return circuit due to variation of oil flow to
give a bad effect on valves.
Since mixing foreign substances with the hydraulic oil
exerts an bad effect on hydraulic equipment, be sure to fit
suction filter and return filter.
4-1
5. PIPING PROCEDURES
q MOUNTING OF CONTROL VALVE

1. Recommended position for mounting control valve
Slewing motor
Slewing center

Control valves
Operators position
2. Preparation of a cover
When the crane is to be operated with the control valves set up outside and the crane itself will
be left for a long period of time, it is recommended to put a cover over the valves to maintain
normal functions of the valves.
5-1
PIPING PROCEDURES
w HOSE CONNECTION
When piping on the side or on the bottom side, connect each hydraulic equipment by referring
to each piping example.
In addition, when designing hydraulic circuit all over the ship on the customer side, return oil
out of the control valves for the crane to the oil tank directly.
1. Recommended connection of hydraulic equipment when piping on the side

Piping length and pipe size being applied may allow piping resistance to be increased causing
troubles with the crane.
Lay pipes in accordance with CAUTION FOR PIPING illustrated on page 5-8 .
Allowable back pressure

for out port of control
valve is less than
0.3Mpa {3kgf/cm2}

for drain port of winch
motor is less than
0.3Mpa {3kgf/cm2}

Control valve
for drain port of slewing

motor is less than
0.3Mpa {3kgf/cm2}
Load meter
Filter (return side)
Hydraulic pump: Connect drain

port directly to
M or E oil tank.
type
Open type oil tank

Filter (suction side) (Capacity of tank must be that of
more than 1.5 times of rated flow)
5-2
PIPING PROCEDURES
2. Recommended connection of hydraulic equipment when piping on the

bottom side
Lay the hoses come out of the bottom side of the crane body according to the instruction sticker
stuck on the securing hardware of the hoses
Piping length and pipe size being applied may allow piping resistance to be increased causing
troubles with the crane.
Lay pipes in accordance with CAUTION FOR PIPING illustrated on page 5-8 .

for out port of control
valve is less than
0.3Mpa {3kgf/cm2}

for drain port of winch
motor is less than
0.3Mpa {3kgf/cm2}

Control valve
for drain port of slewing

motor is less than
0.3Mpa {3kgf/cm2}
Load meter
Filter (return side)
Hydraulic pump: Connect drain

port directly to
M or E oil tank.
type
Open type oil tank

Filter (suction side) (Capacity of tank must be that of
more than 1.5 times of rated flow)
5-3
PIPING PROCEDURES
e PIPING PORT CONNECTING CONTROL VALVE

Weight: 15kg
From pump: Mounting bolts M10 (4pcs)
IN-port G1/2 (PF1/2)
Derricking
Derrick (lower):
G3/8(PF3/8)
Hoisting
Derricking (raise): Hoisting (down):
G3/8(PF3/8) G3/8(PF3/8)
Hoisting (up):
RC3/8(PT3/8)
Telescoping Telescoping
(retract): Telescoping
G3/8(PF3/8) (extend):
G3/8(PF3/8)
Slewing (C.W.):
G3/8(PF3/8)
Slewing
To tank OUT port: 100

Slewing (C.C.W.):
G3/4(PF3/4) G3/8(PF3/8)
34 28
22.6+0.1 +0.1 30.8+0.1
18.6
0 15 0 0
15 1 1 15
R0.50.1 R0.50.1 3.5 +0.4

2.5 +0.4 2.5 +0.4 0
0 45 0 45
G1/2 G3/8 G3/4
45 (PF3/8)
(PF1/2) (PF3/4)
(7 places)
DETAILED ACTUATOR PORT DETAILED OUT PORT
DETAILED IN PORT (applicable O-ring: P-14) (applicable O-ring: P-24)
(applicable O-ring: P-18)
5-4
PIPING PROCEDURES
r PORTS CONNECTING TO PIPING ON THE SIDE

Note) Shape of slewing motor for UBA500 series is different from others.
Derricking (raise):
Rc3/8(PT3/8)
Hoisting (up):
Rc3/8(PT3/8)
Slewing (C.C.W.):
Rc3/8(PT3/8)
Telescoping (retract): Slewing (C.W.):
Rc3/8(PT3/8) Rc3/8(PT3/8)
Derricking (lower):
Rc3/8(PT3/8) Drain for slewing:
Hoisting (down): Rc1/4(PT1/4)
Rc3/8(PT3/8)
Telescoping (extend):
Rc3/8(PT3/8)
Drain for hoisting:
Rc1/4(PT1/4)
5-5
PIPING PROCEDURES
t HOSES CONNECTING TO PIPING ON THE BOTTOM SIDE

The crane is to be shipped with piping system on the side.
In order to change it from the piping on the side to that on the bottom side, follow procedures
illustrated below.
PROCEDURES
Unfasten M8 bolts (6 places) mounting the plate for piping on the side to remove the plate.
Disconnect the hoses out of the plate to put them out to lower side.
Put the cover over the window on the side.
Ordering name: Cover P/N: 088D565030
Length of hoses from bottom face
of base
Model Hose length

Plate for piping Approx.
on the side UBA500 SERIES
100mm
Approx.
Bottom face of base UBA340 SERIES
130mm
Approx.
UBA260 SERIES
230mm
1. Position of hoses
When marking on the Bottom surface of
sticker is hard to read, swivel joint
confirm the hose
arrangement on the
basis of the connections
of piping on the side.
Inside of artillery base
Telescoping (extend): Sicker for identifying hose

G3/8 (PF3/8) female
Drain for hoisting:
G1/4 (PT1/4) female
Hoisting (down):
G3/8 (PF3/8) female Derricking (raise):
G3/8 (PF3/8) female
Telescoping (retract):
G3/8 (PF3/8) female Hoisting (up): G3/8 (PF3/8) female
Derricking (lower): G3/8 (PF3/8) female
5-6
PIPING PROCEDURES
2. Shape of hose connections at their bases
PF3/8 (Hose : Q'ty 6)

7.1
G3/8
(PF3/8)
Raising boom
7.5
10
30
11.6 7.5 22 HEX
(70)
PF1/4 (Hose : Q'ty 1)

6.1 Instruction sticker
G1/4
(PF1/4)
Drain
5.5
7
30
11 6.5 19 HEX
(58)
5-7
PIPING PROCEDURES
y CAUTION FOR PIPING

1. Allowable back pressure for each hydraulic equipment of the crane
OUT port of control valve

Less than 0.3Mpa {3kgf/cm2}
Drain port for hoisting

Drain port for slewing

CAUTION
If the back pressure exceeds the allowable level, trouble such
as oil leakage may occur.
Therefore, choose the size of piping with the hardest
operating conditions (working in winter season and back
pressure when in maximum flow) in mind.
Return drain oil both for hoisting and for slewing to the oil
tank by way of separate piping without joining oil returning
from control valves.
Be sure to return draining oil both for hoisting and for
slewing to the oil tank.
Otherwise, hydraulic motor will be damaged.
2. Size of piping
Refer to following table to choose size of piping.
Pipe length 5m or less 513 1325

Between pump 1/2" high-pressure 3/4" high-pressure 1" high-pressure hose
and control valve Pipe size hose or pipe hose or pipe or pipe
17.3mmt2.3mm 21.7mmt2.8mm 27.2mmt2.8mm
(10 (15 (20
Between control Pipe length 3m or less 38

valve and main 3/8" high-pressure hose or pipe 1/2" high-pressure hose or pipe
body Pipe size
13.8mmt2.2mm (8 17.3mmt2.3mm (10
Pipe length 25m or less
Between control
valve and tank Rubber hose or pipe
Pipe size
Inside diameter : 31.8mm
Between winch Pipe length 6m or less 625
(slewing) motor Pipe Pipe
and tank Pipe size
13.8t2.2 (8 17.3t2.3 (10
5-8
PIPING PROCEDURES
u HOW TO CHECK RECOMMENDED ALLOWABLE

BACK PRESSURE IN CONTROL VALVE
Attach a back pressure meter (pressure gauge) to the valve as illustrated below to check the
back pressure.
Pressure gauge
From pump R1/4(PT1/4)

G3/4B
(PF3/4) Bushing
R1/2(PT1/2)
Joint
To tank Rc3/4
(PT3/4)
Busing
O-ring
Piping components
Model
Pressure gauge Bushing Joint Bushing O-ring
URA500 series GV50-173
(NAGANO SBU04-020J B-516159 A-514273 P18Hs90
MEARSURING
URA340 series 1pcs 1pcs 1pcs 1pcs
INSTRUMENT CO.)
Measurement range (728690402) (022765121) (022362120) (731291018)
URA260 series 2.5Mpa 1 unit
Figures within brackets indicate part number and corresponding parts are available
at this company.
5-9
PIPING PROCEDURES
i HYDRAULIC CIRCUIT OF CRANE
UBA260 series, UBA340 series : q=69.0cm3/rev

UBA500 series : q=40.1cm3/rev
Slewing
Control valve
G3/4
(MV-30A)
T (PF3/4)
Telescoping
Hoist up
Load meter
Hoisting
URA260 series : q=22.0cm3/rev

URA340 series, URA500 series
: q=24.5cm3/rev
G.P
Rc1/4
(PT1/4)
Derricking
P G1/2
(PF1/2)
UBA260 series 17.2Mpa (175kgf/cm2) at 53l/min.

5-10
6. ZERO-POINT ADJUSTMENT OF LOAD METER
In case where the load meter does not read O (zero) when hoisting hook with no load, adjust it by
following procedures illustrated below.
1. Unfasten the cross-head screws (3 places) to remove the front cover.
Pointer
Knob
Front cover
Screws (3 places)
2. When allowing the pump to be rotated at a low speed (in case of adjusting type) and winding
up the hook with no load, adjust the pointer to indicate 0 (zero) while the center knob is
being fixed.
3. Attach the cover after the pointer has been adjusted.
CAUTION
The load meter indicates the weight of a cargo only while it
is being hoisted up, and the meter cannot be used when
other operation (winding down, stop, and other) is carried
out.
6-1
7. ATTACHMENT OF CHART OF RATED LOAD STICKERS
2 (two) stickers of the chart of rated load are provided and the one has been stuck to the crane
before shipping.
Since the other one is attached as a sheet, stick it to a position near the crane control levers
where an operator can refer to it easily.
The figure shows the chart of rated load for UBA344 as an example
Working range chart
81
11 70
10 60 Boom angle
Lift of hook
50

Lift above ground (m)
Lift of hook 40

30

Lift of hook

20

Lift of hook
10

1
1 1+2 1+2+3 1+2+3+4
Boom length 3.48m 5.68m 7.85m 10.00m 9.86

Mounting surface 10
of crane
Working radius (m)
Note: The chart illustrates for the crane working on no-load condition and
shift due to deflection of the boom is not incorporated.
Chart of rated load
Boom-sections extended 1 1+2 1+2+3
Working radius (m) 3.0 5.5 6.0 6.5 7.0 7.71

Rated load (kg) 950 850 770 700 650
Boom-sections extended 1+2+3+4

Working radius (m) 4.25 4.5 5.0 6.0 7.0 8.0 9.0 9.86
Rated load (kg) 950 900 800 700 600 530 470 450
Note: 1. The chart shows hoisting capacity when the crane has been set up
level and the data are based on actual working radius by
incorporating shift due to deflection of the boom when loaded.
2. The rated loads listed above are based on the strength of the crane
and stability of the mounted vessel is not considered.
Therefore, operate the crane by paying special attention to the stability
of the vessel.
7-1
8. RECOMMENDED COMPONENTS
q PUMP AND ELECTRIC MOTOR

Model UBA500 series UBA340 series UBA260 series
SGP2A44D2H9-L SGP1A36D2H9-L SGP1-32D2H9-L
For C.C.W. Type
(740240084) (740240087) (740240097)
rotation
With acceleration
Displacement cm3/rev 44.0 (rear port) 36.6 (rear port) 33.2 (rear port)
SGP2A44D2H9-R SGP1A36D2H9-R SGP1A32D2H9-R
For C.W. Type
(740240085) (740240088) (740240090)
rotation
Displacement cm3/rev 44.7 (rear port) 36.6 (rear port) 33.2 (rear port)
Maximum speed: min -1
1400 1700
rpm (1400) (1700)
Engine drive
Required output: kW [ps] 21.830 19.126 16.923

SGP1-27D2H9-L SGP1-23D2H9-L
For C.C.W. Type
(740240098) (740240099)
Without acceleration
rotation
Displacement cm3/rev 27.8 (rear port) 23.7 (rear port)
SGP1A27D2H9-R SGP1A23D2H9-R
For C.W. Type
(740240092) (740240093)
rotation
Pump
Maximum speed: min -1

1500
rpm (1500)
Required output: kW [ps] 14.620 12.718 11.216
SGP1-23D2H9-L SGP1-20D2H9-L
For C.C.W. Type
(740240099) (740240101)
50Hz area
rotation
Electric motor drive
For C.W. Type
(740240093) (740240094)
rotation
SGP1-20D2H9-L SGP1A18D2H9-L
For C.C.W. Type
(740240101) (740240095)
60Hz area
rotation
For C.W. Type
(740240094) (740240096)
rotation
MITSUBISHI
ELECRTIC SF-JR
CORPORATION
Sealed
Electric motor
HITACHI,
outer-fan LTD.
TFD-KK
type FUJI 15kw 11kw
AC200V, ELECTRIC MLA
4-pole CO., LTD.
TOSHIBA
CORPORATION
FBK21(FBK8)
8-1
RECOMMENDED COMPONENTS
w [OPTIONAL] HYDRAULIC EQUIPMENT

Crane type UBA260 series UBA340 series/UBA500 series
Hydraulic equipment SHU03079-1 SHU03079-2
model (740290033) (740290034)
Output of electric motor 11kW 15kW
Type of electric motor Sealed outer-fan type, 4-pole, AC200V/200220V, 50Hz/60Hz
50Hz 24 32
Rated flow l/min
60Hz 29 38
SGP1A18D2H9-L SGP1-23D2H9-L
Pump
740240095 740240099
Maximum operating pressure
20.6210
kgf/cm2
MPa
For general use: UNIC hydro #46
Hydraulic oil
For use in cold district: UNIC hydro #32
Starting system of electric
Star-Delta starter
motor
Weight (without hydraulic oil)
310 330
kg
Figures within brackets indicate part number and the parts are available at this company.
With rust-proof painting, moss green color (standard).
CAUTION
Install the equipment where rainwater and/or seawater will
not be splashed on them.
8-2
Electric motor (11kW or 15kW)
Relief valve 20.6Mpa (210kgf/cm2)
Return port
Rc1 (PT1) Drain port Rc1/4 (PT1/4)
Electric control panel Return filter
Hydraulic pump Delivery port

Rc1/2 (PT1/2)
Pressure gauge
1100
Tank drain
Rc3/4(PT3/4)
Hydraulic oil tank
(capacity: 130l)
900 550
1150 4-15 800
CAUTION
Check that the power source is AC200V/200~220V,
50/60Hz, 3-phase.
In order to prevent an electric shock, check that grounding
of class 3 has reliably been provided.
Choose electric wire size of 14mm2 for 11kW supply, and
22mm2 for 15kW supply.
8-3
within 800
Control valve G3/8B Hose adapter

Crane body
(PF3/8)
(Derricking) (Hoisting) (Telescoping)
(Slewing) Elbow, 90
Bushing
O-ring Elbow,
O-ring male/female
Hose adapter (OUT) Elbow, 90
(IN) Slewing motor
R3/4
(PT3/4)
G1/2B(PF1/2)
High-pressure Long elbow
High-pressure
rubber hose rubber hose
High-pressure
rubber hose O-ring G3/8B
High-pressure (PF3/8) Hose adapter
rubber hose
High-pressure rubber hose
Piping components (Assy part number 099864000) Weight: Approx. 6kg

Control valve side Crane body side High-tension rubber hose
Crane type
CONTROL VALVE AND CRANE BODY

Hose adapter O-ring Bushing Elbow, Elbow, 90 Hose Long elbow
(Raise (Wind up) (LowerWind (Slewing
(with O-ring) (with O-ring) male/female adapter Retract) down C.W.
Extend) C.C.W.)
UBA500 series P-14 3/81400 3/81350 3/81550 3/82500
G1/2B R3/4
(Hs90) Rc3/4G3/4B R3/8G3/8B R1/4G3/8B G3/8BR3/8 770113134 770113135 770113136 770113137
UBA340 series G1/2B 770290162 770290161 770290168 770250056
731191014 770290167 06NSF 06NSF 06NSF 06NSF
770290160 (1pc) (3pc)
(7pc) (1pc) (5pc) (2pc) -06MUF -06MTF -06MUF -06MUF
UBA260 series (1pc)
(2pc) (1pc) (3pc) (2pc)
Decide mounting position of the control valves based on length of high-tension rubber hoses.
e [OPTIONAL] COMPONENTS FOR PIPING BETWEEN
8-4
The piping joints and fitting hardware for the high-tension rubber hoses are made of stainless steel.
r [OPTIONAL] MOUNTING BASE FOR CONTROL

VALVES
Use mounting bolts on the crane body to attach the mounting base (bracket) for control
valves in common with the body.
2 3 4
Part list
Control valve mounting assembly: 099871000 Weight: 16kg
Item Part name Part number Q'ty

1 Bracket 099871020 1
2 Bolt 711110D25 4
3 Nut 72111110D 4
4 Spring washer 722211100 4
5 Plain washer 722112240 2
8-5
t [OPTIONAL] INSTALLATION OF RADIO/REMOTE

CONTROLLER
Application
Radio remote controller using weak radio wave: RC-500F-33R
Cable remote controller: RC-30S
1. Mounting procedures
A figure in the circle in the illustrations shows the component unique to radio and cable
remote controllers.
CAUTION
Although the remote control valves and the remote control
box have been designed with both water-proof and rust-
proof in mind, it is recommended that they set up in the
cabin as much as possible.
When they have been set up outdoors for inevitable
reasons and the crane is to be left as it is for a long period
of time, it is recommended to cover them to maintain
normal functions.
In case where radio or cable remote controller is to be
installed (when replacing it to a crane in particular), it is
recommended to replace hydraulic oil.
8-6
(1) Fitting remote control valve
Replace the high-tension filter (line filter) element at regular intervals of once a year.
2 3 4
Control valve assembly

10 Sticker (for controlling
in an emergency)
08MM090101pc
Bolt, M10X25
711110D252pcs
Nut, M10
72111110D2pcs
Spring washer, 10
7222111002pcs
Mounting base for 14 SW bolt, M8X20

remote controller 714108D202pcs
8-7
(2) Fitting load meter and piping joints to remote control valves
Add the joint only for winding-up by hoist winch as the hose
fitting hardware is different. (Male/female adapter: 770290154
1pc, O-ring: P-14 Hs90 731191014 1pc)
Joint: 088D65040 1pc

High-pressure rubber hose:
770112052 1pc
Mounting position of
load meter
Gauge port 17
G1/4(PF1/4) O-ring
5
Hexagon plug 731191011 1pc
728890200 1pc
G3/8 Load meter: 770363224, B-518032 1pc

(PF3/8) Joint: 770290052, FJ10-371 1pc
R1/4 Elbow: 088D65030, A-520467 1pc
(PT1/4) Elbow, 90: 770290158, 8022RG04 1pc
Nut: 72111510D, M10X1.25 1pc
Spring washer: 722211100 10 1pc
To port for winding-up of hoist winch

Mounting of load meter in detail
8-8
(3) Connecting the pipes among hydraulic pump, remote control valves,
and crane body
From pump
(IN port) G1/2B (PF1/2)
To tank
(OUT port) G3/4 (PF3/4)
Remote control valves
Refer to page 8-4 for piping components and connection between remote control valves and
crane body.
Refer to pages 5-2, 5-3, and 5-8 for piping of hydraulic pump and remote control valve, and
oil tank.
(4) Fitting control box to mounting base for remote control valves
Sticker (washing prohibited)

01L198040 1pc

Control box assembly

612315000 1pc
POWER
Sticker (power switch)

603099070 1pc

SW bolt M6X15
714206D15 4pcs
ON OFF
8-9
(5) Wiring between remote control valves and control box for remote
control with wire harness (cable)
CAUTION
Refer carefully to the electric wiring diagram (on page 8-17
before carrying out wiring.
Since the radio/remote controller is to be powered by
DC24V, use a suitable converter to change it to the correct
electric power before connection if the power is to be
supplied from commercial AC power source.
When setting up the remote control valves away from the
control box, replace the wire harness with that for 5.0m
specifications (item 25) for wiring.
Do not extend the wires by alteration at an operation site
of the crane.
To solenoid valve, electromagnetic proportional delivery
control valve of remote control valves
7
Delivery valve Bias Slewing C.C.W. Slewing C.W. Tele, Extend Tele. Retract Derricking,
Wire band
Hoisting, Down Hoisting, Up
Down
Derricking, Up
750516001 2pcs
black(white)
yellow(red)
red(yellow)
yellow(green)
blue(black)
blue(green)
red(green)
orange
brown
black
yellow
black
black
black
black
black
black
gray
blue
pink
Connections of
12 remote control
Ground terminal valves and wire
Connector assembly harness

ON OFF
099899040 1pc
11
Wire harness (0.5m)
099899010 1pc
Control box
cable or
25
Connections of control To power source Wire harness (5.0m)

box and wire harness 099899030 1pc
8-10
(6) Fit the earth terminal and make connection to the power source
6
(Note 4)

ON OFF
When making connection to

power source, disconnect
Earth, at mounting connector to fit the parts
7 described below.
of control box
(Note 5) Earth, Black
(Note 1, Note 5)
(To be connected to the
earth terminal of battery 28 29 30 31
To horn on the ship)
Horn FARTH 13
Power source (24V),
Red (white)
BATTERY RR
13 BATTERY (Note 3)
28 29 30 31 (Note 2) Power source (24V), Red
When connecting the horn, (Interlocking with ON/OFF switch
disconnect connector to of hydraulic pump)
fit the parts described below.
8-11
POINTS TO NOTICE WHEN CONNECTING WIRES

Note 1. Polish the earth point with a grinder to connect the earth terminal to the
bared metal surface.
Apply rust preventive coating over the grinded surface after the earth
terminal has been connected.
Note 2. If the horn will not be used, fit the attached connector to take water-
proof measures against the wiring ends.
Note 3. The red wire of supplying power (24V) is to be used to interlock with the
switch turning ON/OFF hydraulic power source on the crane.
Use the wire of red/white for supplying power (24V) if it will not be
interlocked with the switch.
Note 4. Tie up the surplus wires to fix them such as to the bracket for mounting
remote control valves.
Note 5. When an earth cannot be established in case such as on the tank vessel,
fit insulation material to the mounting area of control box as it has been
grounded to the body.
In addition, connect the earth terminal (in Note 1) to the earth terminal of
battery on the ship.
Connection of earth is also applied as above in case of a steel vessel.
8-12
2. Part list for radio/remote controller

UBA260 series remote controller mounting assembly:Device number: 09E098000
UBA340 series remote controller mounting assembly:Device number: 099898000
UBA500 series remote controller mounting assembly:Device number: 096C98000
Accessories for cable remote controller (10m cable), for radio remote controller
(RC-33R-A), and for radio remote controller (RC-100T-A) are different according
to customer requirements.
Confirm each requirement for accessories.
Part list Q'ty
Sipping
Item Part name Part number UBA260 UBA340 UBA500
1 Control box ass'y 612315000 1 1 1 Shipped by unit ass'y
2 Control valve ass'y 605671000 1
Shipped by unit ass'y in
chosen part
5 Hexagon plug 728890200 1 1 1 Fitted to ,,
6 Wire band 750516004 1 1 1
7 Wire band 750516001 4 4 4
Shipped by unit ass'y
8 Sticker (power switch) 603099070 1 1 1
9 Sticker (washing prohibited) 01L198040 1 1 1
10 Sticker (operation in an emergency) 08MM09010 1 1 1 Fitted to ,,
11 Wire harness (0.5m) 099899010 1 1 1
Shipped by unit part
12 Connector ass'y 099899040 1 1 1
after assembly
13 Connector ass'y 619227000 3 3 3
14 SW bolt 714108D20 2 2 2
Shipped by unit ass'y
15 SW bolt 714206D15 4 4 4
16 SW bolt 714205D12 4 4 4 For mounting receiver
17 O-ring 731191011 1 1 1 Fitted to ,,
Accessory, cable remote
18 604171000 1 1 1
controller (10m) Shipped by unit ass'y in
Accessory, radio remote chosen part
19 61RF02000 1 1 1
controller
Options
25 Wire harness (5m) 099899030 1 1 1
28 Plug housing 750528003 3 3 3
29 Double lock plate 750528004 3 3 3 Shipped by unit part
30 Receptacle contact 750501101 3 3 3
31 Rubber plug 750501102 3 3 3
CAUTION
Carefully check the parts being packed and confirm each
item number described on the part list and the item
number shown in the sections illustrating mounting
procedures to carry out assembly.
8-13
3. Part list of accessory for cable remote controller(RC-30S)
6 3 1
5
8
7
4
Item Part number Part name Q'ty Remarks

1~8 6041 71000 Accessories for cable remote controller 1set
1 6031 98000 Remote controller ass'y 1 RC-30S-6
2 6031 04000 Remote controller cable 1 10m long
3 01L1 99060 Storing container 1
4 6040 70010 Spacer 4
5 7114 08080 Bolt 4 M880l
6 7211 11080 Nut 4
7 7221 12080 Plain washer 4
8 7222 11080 Spring washer 4
CAUTION
Carefully check the parts being packed and place the
storing container of item in the cabin.
After crane operation, be sure to store the remote
controller assy and the remote controller cable in
the storing container.
Otherwise, it may cause troubles during operation as
moisture may enter the electric system for which must be
very careful.
8-14
4. Part list of accessory for cable remote controller (RC-500F-33R)

2
4 84 8
5 5
6 7
3
9
1,10,11
Item Part number Part name Q'ty Remarks

1~11 61RF 02000 Accessories for radio remote controller 1set
1 61RF 01T00 Transmitter 1
2 61RF 02R00 Receiver 1
3 7601 10072 Wood screw 1 M512l
4 61RF 02R10 Flexible antenna 1
5 61RF 02R20 Earth antenna 1
6 61RR 00A10 Antenna cable 1 =4m
7 6030 93060 Antenna cable 1 =9m
8 6030 93800 Antenna fitting bracket 1
9 6103 01010 Bag for receiver 1
10 61RF 01020 Cover 1
11 61RF 01030 Plug 1
CAUTION
Carefully check the parts being packed and mount the
receiver in item and the antenna near the control box.
After crane operation, put the transmitter in the bag for
receiver to store it in the cabin.
8-15
UBA260 series 17.2 MPa(175 kgf/cm2) at 53 l/min
UBA340 series 17.2 MPa(175 kgf/cm2) at 60 l/min
Control valve (MRV-32A) UBA500 series 19.6 MPa(200 kgf/cm2) at 60 l/min
G3/4
(PF3/4)
Rc1/4
G.P (PT1/4) UBA260 series=69.0 cm3/rev
UBA340 series
Rc UBA500 series=40.1 cm3/rev
Slewing
(Accelerator) P
G1/2
G1/4 (PF1/2)
(PF1/4)
C.W.
Telescoping
a b
a b Hoisting
Up
CAUTION
a b
Load meter UBA260 series:=22.0 cm3/rev

5. Hydraulic circuit diagram for radio/remote controller
UBA340 series
=24.5 cm3/rev
a b UBA500 series
Derricking
hydraulic equipment and machine failure may result.

gives a bad influence on the performance and the life of
If foreign substances are mixed in the hydraulic oil, it
8-16
8P AMP
174262-2
8-17
41
43 red
10P 43 40 14
Battery alarm white/green 8 5 34C white/green white/green 41
14 red/black
white/blue 11 6 white/blue white/blue 40
Trouble alarm 10 black/yellow Control valves
24P
3 black/green blue yellow +
Raise blue 2 4 blue blue 9 black white Raise
gray 4 5 gray gray 7 gray green +
Lower black black Lower
Hoist up yellow 5 6 yellow yellow 5 yellow yellow +
1 black white Hoist up
brown
Hoist down 7 brown brown 3 brown green +
black black Hoist down
Extend pink 16 8 pink pink 1 pink green +
orange 9 black black Extend
Retract 9 orange orange 25 orange yellow +
black white Retract
C.W. violet 14 10 violet
sky-blue 15 15 sky-blue
C.C.W.
3 16 white/red
24 red/blue

11 blue/yellow blue/yellow 23 blue/yellow blue
+
Slewing
12 yellow/blue yellow/blue 22 yellow/blue violet C.W.
C.C.W.
13 blue/black blue/black blue
for slewing
+
Slewing
21 blue/black
Power supply
14 black/white black/white 20 black/white orange C.C.W.
C.W.
Power supply to
Acceleration stop
Over-winding stop
21 blue/green blue/green 29 blue/green blue +
Delivery 22 yellow/green yellow/green 28 yellow/green violet Delivery
24V
23 red/green red/green 27 red/green yellow +
Bias
19 black/red black white Bias
Acceleration 20 black/blue
power supply
electric circuit Power supply for bias
Stop input
Speed input
(24V) red/black 13 2 red/black red/black 13
black
Earth
6 17 white/black
Speed (to control box)
6. Electric wiring diagram for radio/remote controller
green 10 18 green
Horn white 7 1 white
9
Earth (to battery
white/yellow
(0V) black 12 8 black black 50 black
earth terminal on
1 brown/white the ship)
2 yellow/white
Radio equipment (power supply, 0V)
7 green/white green/white 37 green/white
(controller) Horn (Note2)
Power supply 4 red red 42 red 24V (Note 1)
3 red/white red/white 34 red/white
24V (RR), Power supply to
Power T&B T&B radio controlle
supply 102251-24 102231-10
1 3 5 7 9 13 34
Control box 20 21 22 23 25 37 40 41 42
27 28 29 50
Control box
CAUTION
Connect the power supply (24V) so that interlocking with
the ON/OFF switch for hydraulic power source on the
crane can be achieved.
When no interlocking is necessary, connect the power to
the same power supply (24V) as that of 24V (RR) for radio
controller.
If the horn will not be used, fit the water-proof connector to
the ends of wire harness for water-proof measures.
8-18
9. OVERALL VIEW OF CRANES
q UBA263 (3-SECTION BOOM)
(520)
200 200
460
8-24 200 200

Slewing center 460
2760
76 MIN 2590~MID 4520~MAX 6400
185 520
1
(1570)
1310
Nominal weight: 550kg
(1110)
915
6-Rc3/8
(PT3/8)
Rc1/4
(PT1/4)
t22
(230)
Ports for piping on the side

G1/4 Slewing center
(PF1/4)
6-G3/8
(PF3/8) Hoses for piping on the bottom side
9-1
OVERALL VIEW OF CRANES
w UBA264 (4-SECTION BOOM)
(520)
200 200
460
8-24 200 200

Slewing center 460
3110
(76) MIN 2940 ~MID 4870~6790~MAX 8690
185 740
1
(1670)
1310
(1100)
1055
6-Rc3/8
(PT3/8)
Rc1/4
(PT1/4)
t22
(230)

G1/4 Slewing center
(PF1/4)
6-G3/8
9-2
e UBA343 (3-SECTION BOOM)
(540)
140 180 140

520
12-24 140 180 140

Slewing center 520
3490
(90) MIN 3310~MID 5510~MAX 7690
210 690
1
(1740)
1458
(1260)
1080
6-Rc3/8
(PT3/8)
Rc1/4
(130)
t25
(PT1/4)

G1/4
(PF1/4) Slewing center Base center
6-G3/8 24
9-3
r UBA344 (4-SECTION BOOM)
(540)
140 180 140

520
12-24 140 180 140

Slewing center 520
3660
(90) MIN 3480~MID 5680~7850~MAX 10000
210 885
1
(1840)
1458
(1250)
1165
6-Rc3/8
(PT3/8)
(130)
t25
Rc1/4
(PT1/4)

Slewing center Base center
G1/4 24
(PF1/4)
6-G3/8 Hoses for piping on the bottom side
(PF3/8)
9-4
t UBA345 (5-SECTION BOOM)

(540)
140 180 140

520
12-24 140 180 140

Slewing center 520
3720
(90) MIN 3540~MID 5740~7910~10060~MAX 12210
210 960
1
(1920)
1458
(1250)
1195
6-Rc3/8
(PT3/8)
(130)
Rc1/4
t25
(PT1/4)

G1/4
(PF1/4) Slewing center Base center
6-G3/8 24
9-5
y UBA503 (3-SECTION BOOM)
(650)
180 180 180

600
12-26 180 180 180

Slewing center 600
3690
(86) MIN 3510~MID 5940~MAX 8340
240 685
1
(1990)
1617
(1410)
1160
6-Rc3/8
(PT3/8)
Rc1/4
(100)
t28
(PT1/4)
G1/4 Ports for piping on the side

(PF1/4) Slewing center
6-G3/8
9-6
u UBA504 (4-SECTION BOOM)

(650)
180 180 180

600
12-26 180 180 180

Slewing center 600
3850
(86) MIN 3670~MID 6070~8470~MAX 10870
240 875
1
(2040)
1617
(1420)
1250
6-Rc3/8
(PT3/8)
(100)
Rc1/4
t28
(PT1/4)

6-G3/8
9-7
i UBA505 (5-SECTION BOOM)
(650)
180 180 180

600
12-26 180 180 180

Slewing center 600
3910
(86) MIN 3730 ~MID 6130~8530~10930~MAX 13330
240 950
1
(2140)
1617
(1420)
1290
6-Rc3/8
(PT3/8)
(100)
Rc1/4
t28
(PT1/4)

6-G3/8
9-8
HEAD OFFICE : Center Bldg., 3-12, Higashishinagawa 2-chome,
Shinagawa-ku, Tokyo 140-0002, JAPAN

Lap Dat Cau Unic

Uploaded by

Copyright:

Available Formats

Lap Dat Cau Unic

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lap Dat Cau Unic

Uploaded by

Copyright:

Available Formats

INSTALLATION MANUAL

UNIC HYDRAULIC CRANE

HEAD OFFICE : Center Bldg., 3-12, Higashishinagawa 2-chome,

1. GENERAL VIEW ......................1- 1 9. OVERALL VIEW OF CRANES

Slewing Derricking cylinder

center Control lever

W (kg): L (mm): H (mm): h (mm):

w DIMENSIONS OF CRANE BASE FOR INSTALATION

M243.0 Equivalent to 10.9 12pcs

e BASE FOR MOUNTING CRANE

r [OPTION] ROUND-SHAPED BASE

Note: Mounting dimensions of the Note: Mounting dimensions of the

t STORAGE OF BOOM AND HOOK

Set up the hydraulic source by referring to the following table.

UBA500 UBA340 UBA260

Rated flow l/min 60 60 53

Recommended electric motor

2 Use an oil tank of open type.

Suction side: Filtration of 100-mesh.

4 Recommended hydraulic oil:

Use industrial-type hydraulic oil;

q MOUNTING OF CONTROL VALVE

1. Recommended connection of hydraulic equipment when piping on the side

Allowable back pressure

Allowable back pressure

Allowable back pressure

for drain port of slewing

Filter (return side)

Hydraulic pump: Connect drain

Open type oil tank

2. Recommended connection of hydraulic equipment when piping on the

Allowable back pressure

Allowable back pressure

Allowable back pressure

for drain port of slewing

Filter (return side)

Hydraulic pump: Connect drain

Open type oil tank

e PIPING PORT CONNECTING CONTROL VALVE

To tank OUT port: 100

R0.50.1 R0.50.1 3.5 +0.4

r PORTS CONNECTING TO PIPING ON THE SIDE

t HOSES CONNECTING TO PIPING ON THE BOTTOM SIDE

Model Hose length

Inside of artillery base

Telescoping (extend): Sicker for identifying hose

2. Shape of hose connections at their bases

PF3/8 (Hose : Q'ty 6)

PF1/4 (Hose : Q'ty 1)

y CAUTION FOR PIPING

Pipe length 5m or less 513 1325

Between control Pipe length 3m or less 38

u HOW TO CHECK RECOMMENDED ALLOWABLE

From pump R1/4(PT1/4)

i HYDRAULIC CIRCUIT OF CRANE

UBA260 series, UBA340 series : q=69.0cm3/rev

URA260 series : q=22.0cm3/rev

UBA260 series 17.2Mpa (175kgf/cm2) at 53l/min.

3. Attach the cover after the pointer has been adjusted.