BUCKET CAPACITY

3.6 - 5.2 m3
4.7 - 6.8 yd3

WA470-5
WA
470

WHEEL LOADER

Photo may include optional equipment.

 WA470-5 Wheel Loader

W ALK-A
WALK -AROUND
ROUND
Excellent Operator Environment
Automatic transmission with selectable modes
Electrically controlled transmission lever
Fingertip control levers
Pillar-less large ROPS/FOPS cab
High Productivity Easy entry/exit, rear-hinged doors
& Low Fuel Consumption Telescopic/tilt steering column
See page 8.
Powerful engine
Dual-mode engine power select system
Transmission mode select system
Dual speed hydraulic system
Superior dumping clearance and reach
Long wheelbase and 40 degree articulation
See page 4.

Harmony with Environment

EPA Tier 2 and EU Stage 2 emissions certified
Low fuel consumption

2
 WA470-5
WHEEL LOADER

NET HORSEPOWER
Increased Reliability 195 kW 261 HP @ 2000 rpm

Reliable Komatsu designed and Cathion electrodeposition process OPERATING WEIGHT

manufactured components is used to apply primer paint 22085 22315 kg
Sturdy main frame Powder coating process is used to 48,690 49,195 lb
Maintenance-free fully hydraulic, apply on main structure BUCKET CAPACITY
wet disc service and parking brakes Sealed DT connectors for electrical 3.6 5.2 m3
All hydraulic hoses use flat face connections 4.7 6.8 yd3
O-ring seals
See page 6.

Photo may include optional equipment.

Easy Maintenance
EMMS (Equipment Management Prolonged engine oil change interval
Monitoring System) Ground check for windshield washer
Reversible radiator fan (optional) tank and coolant tank
Swing-out aftercooler and Easy access gull-wing type engine
oil coolers side doors
See page 7. 3
 P
PRODUCTIVITY
RODUCTIVITY
F
FEATURES
EATURES
High Productivity and Low Fuel Consumption
Powerful Engine Transmission Mode Select System
The electronically controlled fuel injection timing in the This operator controlled system allows the operator to
SAA6D125E-3 engine provides optimum combustion of fuel select manual shifting or three levels of automatic shifting
at both low and high speed/power applications. This system (low, medium, and high).
also provides fast throttle response to match the machines Manual: Transmission is
powerful rim pull and fast hydraulic response. fixed to gear speed selected
with gear shift lever.
195 kW 261 HP
Auto. L: This mode
The common rail type fuel injection system provides
provides smooth gear
maximum power with minimum emissions. This engine is
change and low fuel
EPA Tier 2 and EU Stage 2 emissions certified.
consumption since gear
Low Fuel Consumption shifting is performed at relatively low engine speeds,
suitable for general excavating and loading.
The fuel consumption is reduced greatly because of the
low-noise, high-torque engine and the large-capacity torque Auto. M: Gear is shifted at medium engine speeds
converter with maximum efficiency in the low-speed range. between those of L and H modes.

Reduction of Fuel Consumption: 15% (compared with Auto. H: This mode provides large rim pull and short
Dash 3 technology). cycle time since gear shifting is performed at relatively
high engine speeds, suitable for load and carry operation
Dual-Mode Select System on uphill.
This wheel loader offers two selectable operating modes
New Dual-Speed Hydraulic System
Normal and Power. The operator can adjust the machines
performance by flipping a switch. Komatsus dual-speed hydraulic system increases
operational efficiency by matching the hydraulic demands
Normal Mode: This mode
to work conditions.
provides maximum fuel
efficiency for most of Oil from the switch pump is completely returned to the tank
general loading. when digging and breaking out, therefore, hydraulic flow
Power Mode: This mode to the loader is reduced and pressure is increased. This
provides maximum power reduces horsepower demand from the engine and makes
output for hard digging the operation more efficient. Kick-down switch signal also
operation or hill climb. controls the oil flow. This new technology is greater
productivity at the lowest operating cost.

When digging / scooping

Loader pump

Switching pump
Cut-off
valve

Tank

All the oil from the switching pump returns to the tank.
Hydraulic load is reduced and large power flows to the tires.

When raising lift arm Loader pump

Switching pump
Cut-off
valve

Tank

All the oil from the switching pump flows to the work equipment.
4 The raising speed of the lift arm is increased.
 WA470-5
WHEEL LOADER

Maximum Dumping Clearance and Reach Long Wheelbase/Articulation Angle of 40

The long lift arms provide The longest wheelbase in class and the widest tread provide
high dumping clearances improved machine stability in both longitudinal and lateral
and maximum dumping directions. Since the articulation angle is 40, the operator
reach. The operator can can work efficiently even in the tightest job sites.
even level loads on the
Tread 2300 mm 7'7"
body of a dump truck Wheelbase 3450 mm 11'4"
easily and efficiently. Minimum turning radius (center of outside tire) 5900 mm 19'4"

40

Dumping Clearance: 3185 mm 10'5"

Dumping Reach: 1235 mm 4'1"
(4.2 m3 5.5 yd3 bucket with B.O.C., 26.5-25 tires)

5
 IINCREASED
NCREASED
R
RELIABILITY
ELIABILITY
Komatsu Components
Komatsu manufactures the engine, torque converter,
transmission, hydraulic units, electric parts, and even each
bolt on this
wheel loader.
Komatsu Components
Komatsu torque converter

loaders are
manufactured High-rigidity Frames
with an The front and rear frames have high rigidity to bear twisting
integrated and bending loads applied repeatedly to the loader body.
production Both upper and lower center pivot bearings are tapered
system under transmission engine
front axle rear axle roller bearings having high durability. The structure is similar
a strict quality to those of large-sized loaders and the reinforced loader
control system. linkage also ensures high rigidity.

Wet multi-disc brakes and fully hydraulic braking Flat Face-to-Face O-Ring Seals nipple
system mean lower maintenance costs and higher
Flat face-to-face O-ring seals
reliability. Wet disc brakes are fully sealed. Contaminants
are used to securely seal all
are kept out, reducing wear and resulting maintenance.
hydraulic hose connections
Brakes require no adjustments for wear, meaning even hose O-ring
and to prevent oil leakage.
lower maintenance. The new parking brake is also an
In addition, buffer rings are buffer rings
adjustment-free, wet multi-disc for high reliability
installed to the head side of
and long life.
the all-hydraulic cylinders to
Added reliability is designed into the braking system by the lower the load on the rod
dust seal
use of two independent hydraulic circuits. Provides hydraulic seals and maximize rod packing
backup should one of the circuits fail. the reliability.

Fully hydraulic brakes mean no air system to bleed,

Cathion Electrodeposition Primer Paint/
or the condensation of water in the system that can
Powder Coating Final Paint
lead to contamination, corrosion, and freezing.
Cathion electrodeposition paint is applied as a primer
paint and powder coating is applied as topcoat to the
exterior metal sheet parts. This process results in a
beautiful rust-free machine, even in the most severe
environments. Some external parts are made of plastic
providing long life and high impact resistance.

Sealed DT Connectors
Main harnesses and controller connectors are equipped
with sealed DT connectors providing high reliability, water
resistance and dust resistance.

6
 WA470-5
WHEEL LOADER

E
EASY
ASY
M
MAINTENANCE
AINTENANCE
EMMS (Equipment Management
Monitoring System)
Monitor is mounted in front of the operator allowing the
operator to easily check gauges
and warning lights. A specially
designed two-spoke steering
wheel allows the operator to easily see the instrument panel.
Maintenance Control
and Troubleshooting Functions
Action code display function. If the loader has any
troubles, the monitor displays action details on the
character display at the center bottom of the monitor.
Monitor function. Controller monitors engine oil level,
Gull-wing Type Engine Side Doors Open Wide
pressure, coolant temperature, air cleaner clogging etc.
The operator can open and close each gull-wing type engine
If controller finds abnormalities, all of these are displayed
side door easily with the assistance of a gas spring to
on LCD.
perform daily service checks from the ground.
Replacement time notice function. Monitor informs
replacement time of oil and filters on LCD when it reaches
replacement intervals. Lengthened Maintenance Interval
Trouble data memory function. Monitor stores Lengthened engine oil replacement interval:
abnormalities for effective troubleshooting. 250 H 500 H

Lengthened drive shaft greasing interval:

Reversible Cooling Fan (Optional) 1000 H 4000 H
and Swing-out Cooler Elements
If the machine is
operating in adverse
conditions, the
operator can reverse
the hydraulic cooling
fan from inside the
cab by turning on a
switch on the control
panel. The coolers can
also swing out for
easy cleaning.

7
 O
OPERATOR
PERATOR
E
ENVIRONMENT
NVIRONMENT
Easy Operation
Automatic Transmission with ECMV Variable Transmission Cut-off
Automatic transmission with ECMV automatically selects the The operator can adjust the transmission cut-off connected to
proper gear speed based on travel speed, engine speed, and the left brake pedal with the switch near the operators seat
other travel conditions. The ECMV (Electronically Controlled to set the brake/cut-off point for easier operation and higher
Modulation Valve) system engages the clutch smoothly to operating performance in variable operating conditions.
prevent lags and shocks when shifting. This system provides High cut-off pressure for digging operations.
efficient machine operation and a comfortable ride.
Low cut-off pressure for truck-loading operations.
Kick-down
1st 2nd 3rd 4th
switch: Consider 1st hold
Telescopic/Tilt
this valuable Steering Column
2nd hold

feature for added The operator can

3rd auto change
productivity. With tilt and telescope
4th auto change
the touch of the steering column
a finger, the kick-down switch to provide a
kick-down switch comfortable working
automatically downshifts from second to first when position.
beginning the digging cycle. It automatically upshifts from
first to second when the direction control lever is placed Fingertip Work Equipment Control Lever
in reverse. This results in increased rim pull for better New PPC control levers are used for the work equipment.
bucket penetration and reduced cycle times for higher The operator can easily operate the work equipment with
productivity. fingertip control, reducing operator fatigue and increasing
Hold switch: Auto shift is selected and if the operator controllability.
turns on this switch when the lever is at the 3rd or 4th
gear speed position, the transmission is fixed to that
gear speed.

Electrically Controlled Transmission Lever

Easy shifting and
directional changes
with Komatsu two-lever
electronic shifting.
Change direction or
shift gears with a touch
of the fingers without
removing the shifting
hand from the steering
wheel. Solid state electronics and conveniently located
direction and gear shift controls make this possible.
Automatic shifts in ranges two through four keep
production high and manual shifting at a minimum.

8
 WA470-5
WHEEL LOADER

Comfortable Operation
Low-noise Design Rear-hinged Full Open Cab Door
The large cab is mounted with The cab door hinges are
Komatsus unique ROPS/FOPS installed to the rear side
viscous mounts. The low-noise of the cab providing
engine, hydraulically driven fan, and a large opening angle
hydraulic pumps are mounted with rubber cushions, and the for the operator to enter
cab sealing is improved to provide a quiet, and exit. The steps
low-vibration, dustproof with pressurizing, and comfortable are designed like a
operating environment. staircase, so that the
operator can get on
Pillar-less Large Cab and off the cab easily.
A wide pillar-less flat
glass provides excellent Emergency Brake
front visibility. The wiper If the brake oil pressure drops, the warning lamp flashes
arm covers a large area and the warning buzzer sounds intermittently. If the brake
to provide great visibility pressure drops lower, the parking brake is applied providing
even on rainy days. a double safety system.

The cab area is the largest in its class providing maximum

space for the operator.

9
 S
SPECIFICATIONS
PECIFICATIONS

ENGINE STEERING SYSTEM

Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Komatsu SAA6D125E-3 Type . . . . . . . . . . . . . . .Articulated type, full-hydraulic power steering

Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Water-cooled, 4-cycle with orbit-roll system
Aspiration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Turbocharged Steering angle . . . . . . . . . . . . . . . . . . . . . . . . . . .40 each direction
Number of cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Minimum turning radius at
Bore x stroke . . . . . . . . . . . . . . . . . . .125 mm x 150 mm 4.9" x 5.9" the center of outside tire . . . . . . . . . . . . . . . . . . . . . .5900 mm 19'4"
Piston displacement . . . . . . . . . . . . . . . . . . . . . . . .11.04 ltr 674 in3
Performance:
Flywheel horsepower . . . . . . . . . . . .195 kW 261 HP (SAE J1349) HYDRAULIC SYSTEM
195 kW 265 PS (DIN 6270)
Rated rpm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2000 rpm Steering system:
Fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Direct injection Hydraulic pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Gear pump
Governor . . . . . . . . . . . . . . . . . . . . . . . .Electronic, all-speed control Capacity . . . . . . . . . . . .146 ltr/min 38.6 U.S. gal/min at rated rpm
Lubrication system: Relief valve setting . . . . . . . . . . . . . . . . . . . .210 kgf/cm2 3,000 psi
Lubrication method . . . . . . . . . . . . . . .Gear pump, force-lubrication Hydraulic cylinders:
Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Full-flow type Type . . . . . . . . . . . . . . . . . . . . . . . . . .Double-acting, piston type
Air cleaner . . . . . . . . . . . . . . . . . .Dry type with double elements and Number of cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
dust evacuator, plus dust indicator Bore x stroke . . . . . . . . . . . . . .100 mm x 441 mm 3.9" x 17.3"
EPA Tier 2 and EU Stage 2 emissions certified. Loader control:
Hydraulic pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Gear pump
Capacity . . . . . . . . . . . .303 + 120 ltr/min 80.0 + 31.7 U.S. gal/min
TRANSMISSION at rated rpm
Relief valve setting . . . . . . . . . . . . . . . . . . . .210 kgf/cm2 3,000 psi
Torque converter:
Hydraulic cylinders:
Type . . . . . . . . . . . . . . . . . . . .3-element, single-stage, single-phase
Type . . . . . . . . . . . . . . . . . . . . . . . . . .Double-acting, piston type
Transmission:
Number of cylindersbore x stroke:
Type . . . . . . . . . . . . . . . . . . . . . . .Full-powershift, countershaft type
Lift cylinder . . . . . . . . . . . . .2180 mm x 764 mm 7.1" x 30.0"
Travel speed: km/h mph
Bucket cylinder . . . . . . . . .1200 mm x 575 mm 7.9" x 22.6"
Measured with 23.5-25 tires
Control valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-spool type
1st 2nd 3rd 4th Control positions:
Forward 5.8 3.6 11.2 7.0 20.2 12.6 33.1 20.6 Boom . . . . . . . . . . . . . . . . . . . . . . . .Raise, hold, lower, and float
Reverse 6.1 3.8 11.9 7.4 21.4 13.3 34.7 21.6 Bucket . . . . . . . . . . . . . . . . . . . . . . . . .Tilt-back, hold, and dump
Hydraulic cycle time (rated load in bucket)
Measured with 26.5-25 tires Raise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.0 sec
1st 2nd 3rd 4th Dump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.4 sec
Forward 6.3 3.9 12.1 7.5 21.7 13.5 34.9 21.7 Lower (Empty) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.7 sec
Reverse 6.7 4.2 12.8 8.0 23.0 14.3 36.0 22.4

SERVICE REFILL CAPACITIES

AXLES AND FINAL DRIVES Cooling system . . . . . . . . . . . . . . . . . . . . . . . . . .50 ltr 13.2 U.S. gal
Fuel tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . .390 ltr 103.0 U.S. gal
Drive system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Four-wheel drive
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 ltr 10.0 U.S. gal
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Fixed, semi-floating
Hydraulic system . . . . . . . . . . . . . . . . . . . . . . . .186 ltr 49.1 U.S. gal
Rear . . . . . . . . . . . . . . . . . . . . . . .Center-pin support, semi-floating,
Axle (each front and rear) . . . . . . . . . . . . . . . . . .52 ltr 13.7 U.S. gal
30 total oscillation
Torque converter and transmission . . . . . . . . . . .60 ltr 15.9 U.S. gal
Reduction gear . . . . . . . . . . . . . . . . . . . . . . . . . . . .Spiral bevel gear
Differential gear . . . . . . . . . . . . . . . . . . . . . . . . . . .Conventional type
Final reduction gear . . . . . . . . . . . . .Planetary gear, single reduction
BUCKET SELECTION GUIDE

Bucket fill factor

BRAKES
115 100 95%
Service brakes . . . . . . . . . . . . . . . . . . . . . . . .Hydraulically actuated,
wet disc brakes actuate on four wheels m3 yd3
Light Material Bucket with BOC
Parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Wet disc brake 5.2 6.8 (Scooping and loading of light material)
Emergency brake . . . . . . . . . . . . . .Parking brake is commonly used
Bucket capacity: m 3 yd3

Loose Material Bucket with BOC

4.6 6.0 (Loading of crushed stone and dry sand)

Stockpile Bucket with BOC

(Loading and excavating of soil, sand and
4.2 5.5 variety of other commonly handled material)

Excavating Bucket with BOC

3.8 5.0 Excavating Bucket with Teeth and Segment Edge
(Loading and excavating of crushed or blasted rock)

Excavating Bucket with Teeth

3.6 4.7 Rock Bucket with Teeth (Spade Nose)
(Loading and excavating of blasted rock)

lb/yd3 1686 2023 2360 2698 3035 3372 3709

10 kg/m3 1000 1200 1400 1600 1800 2000 2200
Material density: kg/m 3 lb/yd3
 WA470-5
WHEEL LOADER

DIMENSIONS

Measured with 26.5-25-20PR (L3) tires

Tread 2300 mm 7'7"

Width over tires 3010 mm 9'11"
45 A Wheelbase 3450 mm 11'4"
B Hinge pin height, max. height 4360 mm 14'4"
B C Hinge pin height, carry position 585 mm 1'11"
G D Ground clearance 525 mm 1'9"
F
E Hitch height 1240 mm 4'1"
50
E F Overall height, top of the stack 3080 mm 10'1"
C D G Overall height, ROPS cab 3460 mm 11'4"

General Purpose Buckets Loose Light

Rock
Material Material
Bucket
Stockpile Excavating Bucket Bucket
Bolt-on Teeth Bolt-on Teeth Bolt-on Teeth Bolt-on
Cutting and Teeth Cutting and Teeth Teeth Cutting and Teeth Cutting
Edges Segments Edges Segments Edges Segments Edges
Bucket capacity: heaped 4.2 m3 4.2 m3 3.9 m3 3.8 m3 3.8 m3 3.6 m3 3.6 m3 4.6 m3 4.6 m3 4.3 m3 5.2 m3
5.5 yd3 5.5 yd3 5.1 yd3 5.0 yd3 5.0 yd3 4.7 yd3 4.7 yd3 6.0 yd3 6.0 yd3 5.6 yd3 6.8 yd3
struck 3.5 m3 3.5 m3 3.3 m3 3.2 m3 3.2 m3 3.1 m3 3.1 m3 3.9 m3 3.9 m3 3.7 m3 4.5 m3
4.6 yd3 4.6 yd3 4.3 yd3 4.2 yd3 4.2 yd3 4.1 yd3 4.1 yd3 5.1 yd3 5.1 yd3 4.8 yd3 5.9 yd3
Bucket width 3170 mm 3190 mm 3190 mm 3170 mm 3190 mm 3190 mm 3170 mm 3170 mm 3190 mm 3190 mm 3170 mm
10'5" 10'6" 10'6" 10'5" 10'6" 10'6" 10'5" 10'5" 10'6" 10'6" 10'5"
Bucket weight 2005 kg 2055 kg 1930 kg 2150 kg 2200 kg 2070 kg 2165 kg 2200 kg 2250 kg 2125 kg 2185 kg
4,420 lb 4,530 lb 4,255 lb 4,740 lb 4,850 lb 4,564 lb 4,773 lb 4,850 lb 4,960 lb 4,685 lb 4,817 lb
Dumping clearance, 3185 mm 3060 mm 3060 mm 3235 mm 3110 mm 3110 mm 2975 mm 3055 mm 2930 mm 2930 mm 3035 mm
max. height and 45 dump angle* 10'5" 10'0" 10'0" 10'7" 10'2" 10'2" 9'9" 10'0" 9'7" 9'7" 9'11"
Reach at max. height and 1235 mm 1335 mm 1335 mm 1185 mm 1285 mm 1285 mm 1435 mm 1365 mm 1465 mm 1465 mm 1385 mm
45 dump angle* 4'1" 4'5" 4'5" 3'11" 4'3" 4'3" 4'8" 4'6" 4'10" 4'10" 4'7"
Reach at 2130 mm (7') 1910 mm 1950 mm 1950 mm 1880 mm 1925 mm 1925 mm 2010 mm 1980 mm 2020 mm 2020 mm 1990 mm
clearance and 45 dump angle 6'3" 6'5" 6'5" 6'2" 6'4" 6'4" 6'7" 6'6" 6'8" 6'8" 6'6"
Reach with arm horizontal 2750 mm 2905 mm 2905 mm 2680 mm 2835 mm 2835 mm 3035 mm 2935 mm 3090 mm 3090 mm 2960 mm
and bucket level 9'0" 9'6" 9'6" 8'10" 9'4" 9'4" 9'11" 9'8" 10'2" 10'2" 9'9"
Operating height (fully raised) 5960 mm 5960 mm 5960 mm 5875 mm 5875 mm 5875 mm 5875 mm 5960 mm 5960 mm 5960 mm 6185 mm
19'7" 19'7" 19'7" 19'3" 19'3" 19'3" 19'3" 19'7" 19'7" 19'7" 20'4"
Overall length 8765 mm 8920 mm 8920 mm 8695 mm 8850 mm 8850 mm 9050 mm 8950 mm 9105 mm 9105 mm 8975 mm
28'9" 29'3" 29'3" 28'6" 29'0" 29'0" 29'8" 29'4" 29'10" 29'10" 29'5"
Loader clearance circle (bucket 13960 mm 14080 mm 14080 mm 13930 mm 14040 mm 14040 mm 13970 mm 14060 mm 14180 mm 14180 mm 14080 mm
at carry, outside corner of bucket) 45'10" 46'2" 46'2" 45'8" 46'1" 46'1" 45'10" 46'2" 46'6" 46'6" 46'2"
Digging depth: 0 80 mm 100 mm 100 mm 80 mm 100 mm 100 mm 85 mm 60 mm 80 mm 80 mm 60 mm
3.1" 3.9" 3.9" 3.1" 3.9" 3.9" 3.3" 2.4" 3.1" 3.1" 2.4"
10 315 mm 360 mm 360 mm 305 mm 350 mm 350 mm 370 mm 345 mm 390 mm 390 mm 350 mm
1'0" 1'2" 1'2" 1'0" 1'2" 1'2" 1'3" 1'2" 1'3" 1'3" 1'2"
Static tipping load: straight 17215 kg 17170 kg 17295 kg 17005 kg 16955 kg 17085 kg 16990 kg 17045 kg 17000 kg 17125 kg 16970 kg
37,950 lb 37,853 lb 38,130 lb 37,490 lb 37,380 lb 37,665 lb 37,455 lb 37,575 lb 37,479 lb 37,755 lb 37,410 lb
40 full turn 14975 kg 14930 kg 15055 kg 14770 kg 14720 kg 14850 kg 14755 kg 14810 kg 14765 kg 14890 kg 14735 kg
33,015 lb 32,915 lb 33,190 lb 32,560 lb 32,450 lb 32,740 lb 32,530 lb 32,650 lb 32,551 lb 32,825 lb 32,485 lb
Breakout force 192 kN 207 kN 207 kN 203 kN 209 kN 220 kN 190 kN 168 kN 183 kN 183 kN 165 kN
43,162 lb 46,534 lb 46,534 lb 45,634 lb 46,983 lb 49,456 lb 42,712 lb 37,766 lb 41,140 lb 41,140 lb 37,092 lb
Operating weight 22165 kg 22210 kg 22085 kg 22205 kg 22315 kg 22185 kg 22280 kg 22225 kg 22270 kg 22145 kg 22300 kg
48,865 lb 48,965 lb 48,690 lb 48,955 lb 49,195 lb 48,910 lb 49,120 lb 48,995 lb 49,097 lb 48,820 lb 49,165 lb
* At the end of tooth or B.O.C.
All dimensions, weights, and performance values based on SAE J732c and J742b standards.
Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, ROPS cab, Air conditioner and operator. Machine stability and operating
weight affected by counterweight, tire size, and other attachments.
Apply the following weight changes to operating weight and static tipping load.

11
 WEIGHT CHANGES

Change
Operating Tipping load Tipping load Width Ground in vertical
weight straight full turn over tires clearance
Tires dimensions

kg lb kg lb kg lb mm ft in mm ft in mm ft in
26.5-25-20PR(L3) 0 0 0 0 0 0 3010 9'11" 525 1'9" 0 0
26.5-25-16PR(L3) 70 155 50 110 45 100 3010 9'11" 525 1'9" 0 0
26.5-25-20PR(L4) +355 +780 +270 +595 +235 +520 3010 9'11" 525 1'9" 0 0
26.5-R25(L3) +115 +235 +90 +200 +75 +165 3010 9'11" 525 1'9" 0 0
23.5-25-20PR(L3) 460 1,015 350 770 300 660 2920 9'7" 460 1'6" 65 3"
23.5-25-20PR(L2) 775 1,710 585 1,290 505 1,115 2920 9'7" 460 1'6" 65 3"
Remove ROPS cab
with A/C 730 1,610 670 1,475 585 1,290
Install additional
counterweight +400 +880 +1030 +2,270 +860 +1,895

STANDARD EQUIPMENT

2-spool valve for boom and bucket Directional signal Rear window washer and wiper
controls EMMS (Equipment Management ROPS/FOPS cab
Additional fuel filter with water separator Monitoring System) Seat, suspension type with reclining
Air conditioner Engine, Komatsu SAA6D125E-3 diesel Seat belt
Alternator, 50 A Engine shut-off system, electric Service brakes, wet disc type
Auto shift transmission with mode Floormat Starting motor, 7.5 kW/24 V
select system Front fender Steering wheel, tiltable
Back-up alarm Lift cylinders and bucket cylinder Sun visor
Back-up lamp Loader linkage with standard lift arm Swing-out aftercooler and oil cooler
Batteries, 150 Ah/2 x 12 V Main monitor panel with speedometer Tires (26.5-25-20PR, L3 tubeless)
Boom kick-out PPC fingertip control, two levers and rims
Bucket positioner Radiator mask, lattice type Transmission, 4 forward and 4 reverse
Counterweight Rearview mirror

OPTIONAL EQUIPMENT

3-spool valve Deluxe suspension seat Log grapple

Additional counterweight Emergency steering (SAE) Ordinary spare parts
AM/FM radio Engine pre-cleaner with extension Power train guard
Brake cooling system Heater and defroster Remote grease (lift arm pivot pin)
Bucket teeth (bolt-on type) High lift arm Starting motor, 11 kW
Bucket teeth (tip type) Hydraulic-driven fan with reverse rotation Tool kit
Counterweight for log KOMTRAX Vandalism protection kit
Cutting edge (bolt-on type) Limited slip differential (F&R)

www.Komatsu.com Printed in Japan 201408 IP. AD

CEN00020-04 Materials and specifications are subject to change without notice

is a trademark of Komatsu Ltd. Japan