Scribd Logo
Upload

Welcome to Scribd!

  • 103 views

    C.C.Pavement Design - P.H.Wada

    Uploaded by

    D.V.Srinivasa Rao
    The document summarizes the design of a concrete pavement. It provides the design parameters used such as the thermal coefficient of concrete, coefficient of friction, unit weight of concrete, design wheel load, modulus of reaction of sub-base, and flexural strength of concrete. It then calculates the radius of relative stiffness, warping stress coefficient, warping stress at edge, residual strength in concrete slab, load stress in edge region, and corner load stress. It determines that the design is safe based on the load stresses being less than the residual strength of the concrete.

    Copyright:

    © All Rights Reserved
    Download as XLS, PDF, TXT or read online from Scribd

    C.C.Pavement Design - P.H.Wada

    Uploaded by

    D.V.Srinivasa Rao
    103 views3 pages
    The document summarizes the design of a concrete pavement. It provides the design parameters used such as the thermal coefficient of concrete, coefficient of friction, unit weight of concrete, design wheel load, modulus of reaction of sub-base, and flexural strength of concrete. It then calculates the radius of relative stiffness, warping stress coefficient, warping stress at edge, residual strength in concrete slab, load stress in edge region, and corner load stress. It determines that the design is safe based on the load stresses being less than the residual strength of the concrete.

    Original Title

    C.C.Pavement Design_P.H.Wada.xls

    Copyright

    © © All Rights Reserved

    Available Formats

    XLS, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document summarizes the design of a concrete pavement. It provides the design parameters used such as the thermal coefficient of concrete, coefficient of friction, unit weight of concrete, design wheel load, modulus of reaction of sub-base, and flexural strength of concrete. It then calculates the radius of relative stiffness, warping stress coefficient, warping stress at edge, residual strength in concrete slab, load stress in edge region, and corner load stress. It determines that the design is safe based on the load stresses being less than the residual strength of the concrete.

    Copyright:

    © All Rights Reserved
    Download as XLS, PDF, TXT or read online from Scribd
    Download as xls, pdf, or txt
    103 views3 pages

    C.C.Pavement Design - P.H.Wada

    Uploaded by

    D.V.Srinivasa Rao
    The document summarizes the design of a concrete pavement. It provides the design parameters used such as the thermal coefficient of concrete, coefficient of friction, unit weight of concrete, design wheel load, modulus of reaction of sub-base, and flexural strength of concrete. It then calculates the radius of relative stiffness, warping stress coefficient, warping stress at edge, residual strength in concrete slab, load stress in edge region, and corner load stress. It determines that the design is safe based on the load stresses being less than the residual strength of the concrete.

    Copyright:

    © All Rights Reserved
    Download as XLS, PDF, TXT or read online from Scribd
    Download as xls, pdf, or txt
    of 3

    DESIGN OF C.C.

    PAVEMENT

    Thermal coefficient of concrete = 10x10-6 per 0C


    Coefficient of friction = 1.5
    Unit wieght of CC = 2400Kg/Cum
    Design wheel load P = 4082Kg
    (Average of rural + permitted)
    Wheel Pressure 1/2 = 7.14Kg/Sqcm
    Radius of contact area a = P/p = 13Cm
    E Value of concrete E = 3x10 Kg/Sqcm
    5

    Poisson's Ratio u = 0.15


    Lane width Lx = 300Cm
    Spacing of contraction joints Ly = 300Cm

    i)Modulus of reaction of sub base(k):-

    The modulus of sub grade reaction(k) corresponding to CBR value of 5% from


    Table(1) of IRC SP 62-2004 is 4.2Kg/cm2/cm

    The C.C pavement is proposed over the existing base course of 75mm thick
    WBM Gr-II .

    Hence the k value can be increased by 20%

    Hence effective 'k' value is 5.0Kg/Sqcm/cm

    ii)Flexural strength of concrete

    Minimum design mix of M30 is recommended by the clause 3.6 of


    IRC SP 62:2004

    Using M30 grade concrete,flexural strength is 0.7 fck

    Hence,the 28-day flexural strength = 3.83Mpa

    For rural roads,it is suggested that the 90-day compressive strength may be used
    instead of 28-day compressive strength,as prescribed by the code.

    Taking 90-day flexural strength for design purpose 45.96Kg/Sqcm

    Assume slab thickness h = 17Cm

    Radius of relative stiffness l = Eh3 1/4

    12K(1-u2)
    = 70.66Cm

    Radius of load contact assumed in circular a = 15Cm

    a/h = 0.7935370895 <1.74

    b = radius of equivalent distribution of pressure

    b = 1.6a2+h2 - 0.675h

    = 12.61Cm

    Lx/l = 4.25

    Warping(Temperature) stress coefficient Cx based on Bradbury's = 0.51


    chart at Lx/l(From Table 3 of IRC SP:62-2004)

    Temperature difference(As recommended in Table 4 of = 19.00C


    IRC:SP:62-2004)

    Warping stress at edge = 15.31Kg/Sqcm


    from Fig.1 of IRC:SP:62-2004

    Residual strength in concrete slab at edge region = 30.65Kg/Sqcm

    Load sress in edge region,

    = (0.529P/h2)(1+0.54u)[4 log10(l/b)+log10b-0.4048]

    = 29.80Kg/Sqcm

    Edge load stress + Warping stress = 45.11Kg/Sqcm <45.96Kg/Sqcm

    Hence safe.

    Factor of safety available = Residual strength


    Edge load stress

    = 1.0286536091 >1

    Hence the design is safe

    Check for corner load stress

    Sc = [3P/h2][1-(ax1.414/l)0.60]

    = 23.06Kg/Sqcm <45.96Kg/Sqcm
    So the design is safe

    You might also like