TM 9-2350-230-12

TM 9-2350-230-12
DEPARTMENT OF THE ARMY TECHNICAL MANUAL
OPERATOR AND ORGANIZATIONAL

MAINTENANCE MANUAL
ARMORED
RECONNAISSANCE/AIRBORNE
ASSAULT VEHICLE
FULL-TRACKED, 152-MM, M551

2350-873 5408
HEADQUARTERS, DEPARTMENT OF HE ARMY

JUNE 1966
This copy is a reprint which includes current pages from Changes I through 14 . Pen-
and-ink changes to be made are listed. For Crew Operating and Maintenance
Instructions, refer to TM 9-2350-23010-1, 29 November 1974, TM 9-2350-230-10/2-1, 31
March 1973, TM 9-2350-230-10-2-2, 31 March 1973, and TM 9-2350-230-102-3, 6 January
1974. For Organizational Maintenance of the Hull and Suspension, refer to TM 9-2350-
230-20-1, 15 February 1975.
WARNING
CARBON MONOXIDE POISONING CAN BE DEADLY
CARBON MONOXIDE IS A’ COLORLESS, ODORLESS, DEADLY POISONOUS GAS, WHICH, WHEN
BREATHED, DEPRIVES THE BODY OF OXYGEN AND CAUSES SUFFOCATION. EXPOSURE TO
AIR CONTAMINATED WITH CARBON MONOXIDE PRODUCES SYMPTOMS OF HEADACHE,
DIZZINESS, LOSS OF MUSCULAR CONTROL, APPARENT DROWSINESS, COMA. PERMANENT
BRAIN DAMAGE OR DEATH CAN RESULT FROM SEVERE EXPOSURE.
IT OCCURS IN THE EXHAUST FUMES OF FUEL-BURNING HEATERS AND

INTERNALCOMBUSTION ENGINES AND BECOMES DANGEROUSLY CONCENTRATED UNDER
CONDITIONS OF INADEQUATE VENTILATION. THE FOLLOWING PRECAUTION
S MUST BE OBSERVED TO INSURE THE SAFETY OF PERSONNEL WHENEVER THE PERSONNEL
HEATER, MAIN OR AUXILIARY ENGINE OF ANY VEHICLE IS OPERATED FOR MAINTENANCE
PURPOSES OR TACTICAL USE.
1. DO NOT OPERATE HEATER OR ENGINE OF VEHICLE IN AN ENCLOSED AREA UNLESS IT IS

ADEQUATELY VENTILATED.
2. DO NOT IDLE ENGINE FOR LONG PERIODS WITHOUT MAINTAINING ADEQUATE VENTILATION IN
PERSONNEL COMPARTMENTS.
3. DO NOT DRIVE ANY VEHICLE WITH INSPECTION PLATES, COVER PLATES, ENGINE COMPARTMENT
DOORS REMOVED UNLESS NECESSARY FOR MAINTENANCE PURPOSES.
4. BE ALERT AT ALL TIMES DURING VEHICLE OPERATION FOR EXHAUST ODORS AND EXPOSURE
SYMPTOMS. IF EITHER ARE PRESENT, IMMEDIATELY VENTILATE PERSONNEL COMPARTMENTS. IF
SYMPTOMS PERSIST, REMOVE AFFECTED PERSONNEL FROM VEHICLE AND TREAT AS FOLLOWS:
EXPOSE TO FRESH AIR; KEEP WARM; DO NOT PERMIT PHYSICAL EXERCISE; IF NECESSARY,
ADMINISTER ARTIFICIAL RESPIRATION.
THE BEST DEFENSE AGAINST CARBON MONOXIDE POISONING IS ADEQUATE VENTILATION.
CAUTION: THE M8A3 AIR FILTER UNIT WILL NOT PROTECT CREW AGAINST CARBON
MONOXIDE POISONING.
WARNING
DO NOT CHAMBER AMMUNITION UNTIL IMMEDIATELY BEFORE FIRING.
AMMUNITION LEFT TOO LONG IN A HOT WEAPON MAY RESULT IN HAZARDOUS CONDITIONS.
FIRE OR REMOVE AMMUNITION WITHIN FIVE MINUTES OF CHAMBERING.

TM 9-2350-230-12
THE FOLLOWING PEN-AND-INK-CHANGES ARE TO BE MADE:
Wherever one of the following model numbers appears, make change as shown;
XM551- ---------------------------------------------------------to M551
XM81E12 (without closed breech scavenger system) to M81
XM81E12 (with closed breech scavenger system) to M81E1
XM44 ------------------------------------------------------------to XM44/XM44E1
XM47 ------------------------------------------------------------to M47
XM48 ------------------------------------------------------------to M48
"Grenade projector" should read "grenade launcher" wherever it appears.

TM 9-2350-230-12
C 14
CHANGE) HEADQUARTERS,
) DEPARTMENT OF THE ARMY
No. 14 ) WASHINGTON, DC, 3 May 1976
Operator and Organizational Maintenance Manual:
ARMORED RECONNAISSANCE/AIRBORNE ASSAULT VEHICLE:

FULL-TRACKED, 152-MM, M551
(2350-00-873-5408)
AND M551A1
(2350-00-140-5151)
TM 9-2350-230-12, 1 June 1966, is changed as follows:
1. New or changed material is indicated by a vertical bar in the margin of the page.
2. Added or revised illustrations are indicated by a vertical bar adjacent to the identification number.
3. Remove old pages and insert new pages as indicated below.
Remove pages Insert pages
vii and viii vii and viii

8-41 and 8-42 8-41 and 8-42
8-80.3 and 8-80.4 8-80.3 and 8-80.4
10-1 and 10-2 10-1 and 10-2
10-5 thru 10-8.4 10-5 thru 10-8.4
None 10-8.5 thru 10-8.14
10-21 and 10-22 10-21 and 10-22
10-29 and 10-30 10-29 and 10-30
10-30.1 and 10-30.2 None
10-31 and 10-32 10-31 and 10-32
10-36.1 and 10-36.2 10-36.1 and 10-36.2
11-9 and 11-10 11-9 and 11-10
11-13 and 11-14 11-13 and 11-14
11-19 thru 11-24.2 11-19 thru 11-24.2
11-27 and 11-28 11-27 and 11-28
Remove pages Insert pages
None 11-29 and 11-30

11-39 and 11-40 11-39 and 11-40
C-7 thru C-10.2 C-7 thru C-10.2
C-27 and C-28 C-27 and C-28
4. File this change sheet in the front of the publication for reference purposes.
By Order of the Secretary of the Army:

FRED C. WEYAND
General, United States Army
Chief of Staff
Official:
PAUL T. SMITH
Major General, United States Army
The Adjutant General
DISTRIBUTION:
To be distributed in accordance with DA Form 12-37 (qty rqr block no. 1025) organizational maintenance requirements for
Armored Reconnaissance/Airborne Assault Vehicle M551 and M551A1.
C10, TM 9-2350-230-12
WARNING
DO NOT FIRE AMMUNITION WITHOUT AUTHORIZED FUZE.
CONVENTIONAL 152 MILLIMETER PROJECTILES ARE ASSEMBLED TO HIGHLY FLAMMABLE,

NONMETALLIC CARTRIDGE CASES. KEEP THIS AMMUNITION AWAY FROM OPEN FLAMES,
LIGHTED CIGARETTES, SMOLDERING RESIDUE AND OTHER SOURCES OF IGNITION.
DO NOT TOUCH, MOVE OR OTHERWISE HANDLE DUDS.
NOTIFY EOD OF LOCATION.
WARNING
RADIATION HAZARD
AZIMUTH DIAL POINTERS ARE TIPPED WITH RADIOACTIVE MATERIAL.
HAZARDOUS RADIATION CONDITIONS EXIST WHEN DIAL WINDOW IS BROKEN OR REMOVED.
ALL MAINTENANCE MUST BE PERFORMED AT DEPOT LEVEL ONLY, EXCEPT FOR

REPLACEMENT OF LAMPS AND REPLACEMENT OF COMPLETE INDICATOR UNIT.
PROTECTION, HANDLING, STORAGE, AND DISPOSAL OF RADIOACTIVE MATERIAL SHALL BE IN

ACCORDANCE WITH TB-MED-232 AND TB 750-237.
TM 9-2350-230-12
C9
Technical Manual
HEADQUARTERS
No. 9-2350-230-12 DEPARTMENT OF THE ARMY
WASHINGTON, D. C., I June 1966
Operator and Organizational Maintenance Manual

ARMORED RECONNAISSANCE/AIRBORNE ASSAULT VEHICLE
FUU-TRACKED, 152-MM, M551
(2350-873-5408)
TABLE OF CONTENTS
Page
CHAPTER 1. INTRODUCTION
Section 1-1. Scope, Security Classification, Maintenance Allocation,
Records, Reports and Equipment Serviceability Criteria ....................................1-1
1-2. Description and Data .................................................................................................1-1
1-3. Safety Precautions.....................................................................................................1-6
CHAPTER 2. OPERATING INSTRUCTIONS

Section 2-1. Service Upon Receipt of Materiel ..............................................................................2-1
Deprocessing Vehicle .........................................................................................2-1
Removal/Installation of Vehicle Closure Kit......................................................... 2-2.3
Removal of Basic Issue Items Saddle ................................................................2-3
Installation of Retracting Slide Assembly on
Cal.. 50 Machine Gun, M2, HB .......................................................................2-4
Installation of Pintle Support, Cradle and Pintle Assembly,
and Cupola Mechanism Switch Assembly ......................................................2-5
break-in Services.................................................................................................2-6
2-2. Vehicle Operation.......... ............................................................................................2-7
Starting, Driving, and Stopping Vehicle ............... .....................................................2-7
Installation and Operation of Driver’s M48 Periscope............................................... 2-12
Vehicle Driving Lights .............................................................................................. 2-13
Amphibious Operation .............................................................................................. 2-15
Erecting Flotation Surfboard and Barrier .............. ................................................... 2-18
Operation of Bilge Pumps..........................................................................................2-20.1
Cold Weather Starting ...............................................................................................2-20.2
Towing Disabled Vehicle and Towing or
Supplying Auxiliary Power to Start Engine ............ ............................................ 2-22
Installation of Two Shackles, Tow Bar or Tow Cables ............................................. 2-23
2-3. Operation of Auxiliary Equipment ............................................................................. 2-24
Operation of M8A3 Air Filter Unit ....................................................................... 2-24
Operation of Personnel Heater........................................................................... 2-27
Operation of Portable and Fixed Fire Extinguishers............. ............................. 2-28
2-4. Operation of Turret and Cupola ................... ........................................................... 2-29
Operation of Turret ................................................................................................... 2-29
Commander’s Ballistic Shield Plate Assemblies .......................................................2-32.2
Operation of Cupola.................................................................................................. 2-33
i
C9, TM 9-2350-230-12
Page
CHAPTER 2. OPERATING INSTRUCTIONS
Section 2-5. Operation of Sighting and Fire Control and
Armament Boresight Procedures .....................................................................2-35
Operation of M119 or M127 Telescope, XM44 Series
Periscope, and Armament Boresight Procedure ...........................................2-36
Aligning 7. 62MM Machine Gun .......................................................................2-40
Operation of Indirect Fire Control Instruments . ................................................2-43
Checking and Adjusting Azimuth Indicator for Accuracy
and Slippage ..................................................................................................2-44
Adjusting M13AlC Elevation Quadrant..............................................................2-45
Installation, Operation, and Boresight Procedure for
Cal.. 50 Machine Gun Night Vision Sight .....................................................2-46
2-6. Operation of Missile Subsystem .................... ........................................................2-48
Energizing the Missile Subsystem .................................................................2-48.1
Lamp and Meter Test .....................................................................................2-48.1
Transmitter Test ............................................................................................2-48.1
Tracker Alignment Test .....................................................................................2-49
De-Energizing the Missile Subsystem .............................................................. 2-50
2-7. Operation of Special Purpose Kits ..........................................................................2-53
Winterization Kit Engine Coolant Heater...........................................................2-53
IR/Whitelight Searchlight Kit..............................................................................2-57
CHAPTER 3. FIRING PROCEDURE
Section 3-1. Misfire, Hangfire, and Cook-off, and Immediate

Action in Case of Failure to Fire ................................................................................3-1
152MM Conventional Ammunition............... .................................................. 3-2.1
7. 62MM Machine Gun ....................................................................................3-2.2
Cal.. 50 Machine Gun, M2, HB...........................................................................3-3
3-2. 152MM Gun-Launcher...............................................................................................3-4
Loading, Firing, and Unloading .......................... ................................................3-5
Checking and Adjusting Recoil Mechanism............. ..........................................3- 8
Closed Breech Scavenger System Operation..................................................3-8.3
Ammunition and Missile Stowage.................. .....................................................3-9
3-3. 7.62MM Machine Gun...........................................................................................3-10.2
Loading, Firing, and Unloading.................. ....................................................3-10.2
7. 62MM Machine Gun Controls.......................................................................3-12
Removal of Live Round or Ruptured Cartridge Case........................................3-13
Removal/Installation ..........................................................................................3-13
3-4. Cal.. 50 Machine Gun, M2, HB ...............................................................................3-14
Loading, Firing and Unloading................... .......................................................3-14
Removal/Installation of Barrel ................... ......................................................3-15
Removing Ruptured Cartridge Case ................. ...............................................3-17
Removal/Installation Cal.. 50 Machine Gun Carrier
Assembly........................................................................................................3-17
Checking and Adjusting Headspace .................................................................3-18
Checking and Adjusting Timing.........................................................................3-20
Installation/Removal of Flash Hider...................................................................3-22
Removal/Installation Gun and Spent Brass Chute........................................3-23
3-5. M176 Grenade Launcher.........................................................................................3-24
Checking Electrical System...............................................................................3-24
Immediate Action in Case of Failure to Fire............ ..........................................3-25
Loading and Firing.............................................................................................3-25
ii
C 10, TM 9-2350-230-12
Page
CHAPTER 4. CREW PREVENTIVE-MAINTENANCE SERVICES
Section 4-1. Preventive-Maintenance Services .............................................................................4-1

Specific Procedures (Normal-Unusual Conditions) . ........ .......................................4-1
Hull Drain Holes.........................................................................................................4-1
4-2. Lubrication .................................................................................................................4-1
Service Intervals (Normal-Unusual Conditions) ........................................................4-1
Turret Floor Access Cover ....................................................................................... 4-10
Cleaning Crew Compartment ................................................................................... 4-11
Checking Firing Probe Continuity ............................................................................. 4-11
Deflating Blisters on CBS Hose .............................................................................. 4-12
Low Pressure Air Radiator Cleaning System ........................................................... 4-12
Engine Bulkhead Access Panel ............................................................................... 4-13
CHAPTER 5. CREW MAINTENANCE
Section 5-1. Repair Parts, Tools, and Equipment..........................................................................5-1

5-2. Troubleshooting ........................................................................................................5-1
5-3. Maintenance of Hull ...................................................................................................5-9
Engine Air Cleaner.................................................................................................... 5-10
Power Plant............................................................................................................... 5-11
Fuel System and Batteries........................................................................................ 5-12
Checking and Adjusting Track Tension .................................................................... 5-13
Removal/Installation of Track ..................... ............................................................. 5-14
Spare Lamps .............................. ............................................................................. 5-15
Draining Coolant and Fuel Systems ......................................................................... 5-17
5-4. Maintenance of Turret, Cupola, Sighting and Fire
Control, and Missile Subsystem Units ...................................................................... 5-19
Spare Lamps ............................................................................................................ 5-19
Cleaning and Inspection - Sighting and Fire Control and
Missile Subsystem Units......... ........................................................................... 5-21
Removal/Installation - M47, M48 Periscopes ........................................................... 5-22
5-5. Maintenance of Armament.........................................................................................5-22.1
Checking and Servicing Counterrecoil Buffer ............ ...............................................5-22.1
Removal/Installation - Evacuator Cylinder ................................................................5-22.2
Cleaning and Lubrication of Gun-Launcher ...............................................................5-24.1
Disassembly/Assembly - 7. 62MM Machine Gun .......... .........................................5-24.2
Disassembly/Assembly - Cal.. 50 Machine Gun, M2, HB ....................................... 5-29
CHAPTER 6. PREPARATION FOR AIR-DELIVERY, STORAGE AND

DESTRUCTION OF MATERIEL TO PREVENT ENEMY USE
Section 6-1. Preparation for Air-Delivery ....................................................................................... 6-1

6-2. Storage.................................................. ....................................................................6-3
Servicing and Processing Vehicle for Storage ....................................................6-3
Missile Shipment and Storage.............................................................................6-3
6-3. Destruction of Materiel to Prevent Enemy Use .........................................................6-4
Destruction Methods and Priority...............................................................................6-4
CHAPTER 7. MATERIEL USED IN CONJUNCTION WITH MAJOR ITEM

Section 7-1. 152MM Gun-Launcher Guided Missiles ....................................................................7-1
Firing Tables and Precautions ...................................................................................7-1
Shillelagh Ammunition Data Chart ............................................................................7-1
Service Upon Receipt of Missiles ..............................................................................7-2
Periodic Inspection of Missiles ..................................................................................7-4
Missile Identification...................................................................................................7-4
iii
C11, TM 9-2350-230-12
Page
CHAPTER 7 MATERIEL USED IN CONJUNCTION WITH MAJOR ITEM
Continued
Section 7-2. Conventional Ammunition for 152MM Gun-Launcher M81 Series ................................. 7-4.1
Identification.................................................................................................................... 7-4.1
Authorized Rounds ......................................................................................................... 7- 4.1
Preparation for Loading .................................................................................................. 7-4.1
Round Types Available................................................................................................... 7-4.5
Preparation for Firing ...................................................................................................... 7-4.7
Cartridges Prepared for Firing But Not Fired ................................................................. 7-4.7
Maintenance ................................................................................................................... 7-4.7
Storage ........................................................................................................................... 7-4.9
7-3. Communications Equipment........................................................................................... 7-5
Communications Data .................................................................................................... 7-5
Radio Sets AN/VRC (Basic Units) and Intercommunication
Equipment ................................................................................................................ 7-6
CHAPTER 8 ORGANIZATIONAL MAINTENANCE INSTRUCTIONS

Section 8-1. General ........................................................................................................................... 8-1
8-2. Troubleshooting .............................................................................................................. 8-8
Transmission Oil Pressure Check Points ....................................................................... 8-10
Ohmmeter Method of Electrical Troubleshooting ........................................................... 8-45
Odometer, Speedometer and Tachometer Troubleshooting.......................................... 8-74.1
8-3 Organizational Preventive-Maintenance Checks and Services . . ................................ 8-75
Preventive-Maintenance Checks and Services - Primary
Armament and Related Equipment .......................................................................... 8-85
CHAPTER 9 ORGANIZATIONAL MAINTENANCE - POWER PLANT AND HULL

Section ............................................................................................................................ 9-1
Power Plant Removal/Installation/Replacement data..................................................... 9-1
Power Plant Removal/Installation ................................................................................... 9-5
Engine Mounts ............................................................................................................... 9-10
Engine Ground Test........................................................................................................ 9-12
9-2. Engine and Components ................................................................................................ 9-13
Engine Fuel System........................................................................................................ 9-14
Engine Coolant System .................................................................................................. 9-14
Filter and Air Cleaner Removal Installation..................................................................... 9-28.1
Blower Assembly and Hose Removal Installation........................................................... 9-28.2
Hull Wiring Harnesses Removal Installation................................................................... 9-28.3
Engine Wiring Harness Removal Installation ................................................................. 9-28.4
9-3. Transmission and Controls ............................................................................................. 9-42
Transmission Internal Brake Adjustment. ...................................................................... 9-43
Accelerator/Throttle Linkage Adjustment........................................................................ 9-46.2
Accelerator/Throttle Control Disassembly ...................................................................... 9-48
Transmission Shift Control Removal .............................................................................. 9-50
Transmission Shift Control Adjustment .......................................................................... 9-52
Transmission Brake Control Adjustment ........................................................................ 9-52.2
Transmission Parking Brake Control Removal/Installation
and Adjustment ........................................................................................................ 9-54
Transmission Brake Control Removal/Installation .......................................................... 9-55
Transmission Land Steer Control Removal/Installation.................................................. 9-58
Transmission Land Steer Control Adjustment ............................................................... 9-60
Transmission Water Steer Control Removal/Installation ................................................ 9-62
Transmission Water Steer Control Adjustment .............................................................. 9-64
Control Handling Precautions ......................................................................................... 9-65
iv
C 11, TM 9-2350-230-12
Page
CHAPTER 9 CRGANIZATIONAL MAINTINANCE - AND PLANT AND HULL
Continued
Section 9-4. Tracks and Suspension ..........................................................................................9-66
Roadwheels .............................................................................................................9-69
Torsion Bar and Roadwheel Arm Removal/Installation ...........................................9-70
Torsion Bar Anchor Removal/Installation ................................................................9-71
Roadwheel Arm Spindle. Disassembly/Assembly ...................................................9-72
Roadwheel Arm Housing and Shaft Disassembly/Assembly...................................9-73
Track Adjuster Removal/Installation ........................................................................9-75
Idler Wheels Removal/lnstallation............................................................................9-76
Idler Hub Assembly Removal/Installation ................................................................9-17
Idler Housing and Spindle Removal/Installation ......................................................9-78
Sprocket Drive Shafts Removal/Installation.............................................................9-79
Sprocket and Carrier Wheels Removal/Installation .................................................9-80
Sprocket Hub and Support Removal/lnstallation .....................................................9-81
Shock Absorber Removal/Installation......................................................................9-82
Suspension System Special Tools ..........................................................................9-84
Track and Track Shoe Replacement .......................................................................9-88
9-5. Hull and Power Plant Electrical................................................................................9-90
Headlight Adjustment...............................................................................................9-95
Headlight Repair ......................................................................................................9-96
Taillight Repair .......................................................................................................9-100
Headlight Dimmer Switch and Auxiliary Power Receptacle,..................................9-102
Dome Lights...........................................................................................................9-103
Batteries.................................................................................................................9-105
Fuel Level Transmitters .........................................................................................9-106
Starter Relay, Neutral Safety and Water Steer Switches, and
Hull Circuit Breakers Removal/Installation ......................................................9-107
Driver’s Switch Panel.............................................................................................9-108
Driver’s Switch Panel Rectifier............................................................................9-110.1
Time Delay Assembly ........................................................................................9-110.2
Turret Master Relay ............................................................................................9-110.3
Electrical Harnesses ...........................................................................................9-110.4
Driver’s Indicator Panel..........................................................................................9-113
Personnel Heater Control Box, ? ...........................................................................9-114
Bilge Pump Relays and Mounts ,...........................................................................9-115
Generator V-Belt Tensioner...................................................................................9-115
Voltage Regulator Removal/Installation/Adjustment..............................................9-116
Generator and Drive Assy. Removal/Installation ..................................................9-117
Engine Starter Removal/Installation.......................................................................9-119
Temperature and Pressure Switches and Transmitters ........................................9-120
Speedometer and Tachometer Generators and
Odometer Adapter Removal/Installation .........................................................9-121
Odometer and Tachometer Drives ........................................................................9-122
Cable Terminals and Connectors Replacement ...................................................9-123
9-6. Hull and Components ............................................................................................9-125
Surfboard and Barrier Supports Adjustment..........................................................9-125
Surfboard and Barrier Disassembly/Repair/Assembly...........................................9-125
Driver’s Rotatable Hatch Latch Release and Latch tops ....................................9-126.6
Driver’s Rotatable Hatch 8eals ..............................................................................9-127
Driver’s Escape Hatch ...........................................................................................9-128
Driver’s Seat . ....................................................................................................9-128.2
Hull Ammunition Racks..........................................................................................9-131
Bilge Pumps...........................................................................................................9-134
Personnel Heater Removal/Installation/Repair......................................................9-137
v
C 11, TM 9-2350-230-12
Page
CHAPTER 9 ORGANIZATIONAL MAINTENANCE POWER PLANT AND HULL
Continued
Section 9-6 Hull and Components - Continued
Fixed Fire Extinguisher Cylinder Replacement and
Control Cable Adjustment ...............................................................................9-144
Fixed Fire Extinguisher Control System Repair ....................................................9-145
Radiator Contamination Shield and Grille Debris
Screens Removal/Installation.......................................................................9-146.1
Battery and Air Cleaner Access Doors ...............................................................9-146.2
Ground Intercom Box Door Assembly ...................................................................9-147
Hull Interior Stowage...........................................................................................9-148.2
Flotation Skin Repair .............................................................................................9-152
Flotation Barrier Repair .........................................................................................9-153
CHAPTER 10. ORGANIZATIONAL MAINTENANCE - TURRET AND CUPOLA
Section 10-1 Turret Electrical Systems.........................................................................................10-1

10-2 Electrical Drive Control System ...............................................................................10-1
Turret Drive Control Checkout Procedure Using Test Set.......................................10-5
Turret Drive Control Test Set Installation..............................................................10-8.4
Accessory Box Removal/Installation/Adjustment..................................................10-8.4
Accessory Box Repair..............................................................................................10-9
Amplifier Integrator Removal/Installation . ............................................................10-10
Motor Generator Removal/Installation ................................................................10-10.1
Motor Generator Brushes Removal/Installation .................................................10-10.2
Gunner’s and Commander’s Control Handle
Removal/Installation ........................................................................................10-12
Power Supply and Gyro Selector Removal/Installation..........................................10-13
Elevating and Traverse Mechanism Clutch Brush
Removal/Installation...............................................................................................10-14
Servo Motors Elevating and Traverse Removal/lnstallation . . ............................10-14
Gun-Launcher Elevation and Depression Bump Stop Adjustment........................10-15
10-3 Conventional Weapons System.............................................................................10-17
Relay Box Removal/Installation .............................................................................10-17
Breech Scavenging Repeat Switch........................................................................10-17
Loader’s Control Box Removal/Installation............................................................10-17
Blasting Machine Removal/Installation ..................................................................10-18
Telescope Emergency Power Supply Box Removal/
Installation..............................................................................................................10-18
120V Firing Circuit Power Supply Box Removal/
Installation ....................................................................................................10-18.1
Low Pressure Air Radiator Cleaning System
Removal/Installation ...........................................................................................10-18.1
Breech Scavenging Compressor Removal/Installation..........................................10-19
Chemical Air Drier Cartridge Removal/Installation .............................................10-20.2
Compressor Air Intake Strainer Removal/Installation .........................................10-20.2
Dipstick and Oil Strainer Removal/Installation....................................................10-20.3
10-4. Missile Subsystem
Checks and Adjustments . . ..............................................................................10-20.4
Signal Data Converter and Modulator Removal/Installation . . ............................10-23
Infrared Transmitter Cover Removal/Installation and
Disassembly/Assembly of Door Latch and Control
Assemblies ...................................................................................................10-24.2
Infrared Transmitter and Door Switch Removal/
Installation..............................................................................................................10-26
Missile Subsystem Power Supply Removal/Installation.........................................10-27
Rate Sensing Unit Removal/Installation.................................................................10-27
vi
C 11, TM 9-2350-230-12
Page
CHAPTER 10. ORGANIZATIONAL MAINTENANCE - TURRET AND CUPOLA ................ Continued
Section 10-4 Missile Subsystem - Continued
Missile Subsystem Test Set Removal/Installation...........................................10-28
Optical Tracker Removal/Installation ..............................................................10-28
10-5. Accessory and Power System . .....................................................................10-29
Circuit Cutout Box Removal/Installation..........................................................10-29
Electric Contact Ring Removal/lnstallation......................................................10-30
Gas-Particulate Filter Unit Removal/Installation..............................................10-32
Radio Antenna Removal/Installation ...............................................................10-34
Cupola Power Box and Control Assembly Removal/
Installation ....................................................................................................10-35
Turret Ventilating Fan Removal/Installation ....................................................10-36
Grenade Launcher 120V Power Supply Removal/
Installation ....................................................................................................10-36
10-6. Turret Components ......................................................................................10-36.2
Turret Traverse Lock Removal/Installation ..................................................10-37
7. 62-,MM Coaxial Machine Gun Feed System Removal/
Installation/Repair ........................................................................................10-38
Commander’s Seat Removal/Installation ........................................................10-38
Gunner’s Seat Removal/Installation................................................................10-40
Loader’s Seat Removal/Installation.................................................................10-42
Turret Cable Guards Removal/Installation ......................................................10-43
Loader’s Hatch Cover......................................................................................10-44
Turret Conventional Ammunition Horizontal
Racks Removal/Installation..........................................................................10-45
Turret Conventional Ammunition Vertical Racks
Removal/Installation.....................................................................................10-46
Turret Missile Rack, Portable Fire Extinguisher,
and Extinguisher and Hose Guard Bracket Removal/
Installation .......................................................................................................10-47
Cupola Vision Blocks Removal/Installation............................................................10-48
Gunner’s Leg Guard and Pad Removal/Installation ..............................................10-48
Telescope Protective Shield Removal/Installation..............................................10-48.3
Cal .50 Maching Gun Mount Support Disassembly/
Assembly......................................................................................................10-48.3
Commander’s Ballistic Shield Plate Assemblies.................................................10-48.4
Turret Interior Stowage .......................................................................................10-48.6
Turret Exterior Stowage.........................................................................................10-49
CHAPTER 11. ORGANIZATIONAL MAINTENANCE - ARMAMENT AND FIRE
CONTROL
Section 11-1. Primary Armament .................................................................................................. 11-1

Firing Mechanism Continuity Check ........................................................................11-2
Counterrecoil Buffer Removal/Installation ...............................................................11-3
In-Battery Switch - Adjustment.................................................................................11-3
Procedure for Cycling CBSS....................................................................................11-4
7. 62-MM Coaxial Machine Gun Mount Removal/
Installation .....................................................................................................11-4.1
Ammunition Spent Brass Chute and Bag Removal/
Installation .........................................................................................................11-5
Recoil Mechanism Hand Pump and Fittings Removal/
Installation .........................................................................................................11-6
Buffer Bleed Line Removal/Installation.................................................................11-6.1
vii
C14, TM 9-2350-230-12
Page
CHAPTER 11 ORGANIZATIONAL MAINTENANCE - ARMAMENT AND
FIRE CONTROL - Continued
Section 11-1 Primary Armament - Continued

Filling and Bleeding Gun Mount Hydraulic System...............................................11-6.1
Gun Mount Hydraulic System Leak Test ..............................................................11-6.2
Recoil Guard Cover and Screen Removal/Installation ............................................11-7
Recoil Mechanism Reservoir and Components
Removal/Installation. ....................................................................................... 11-8
Breech Scavenger Check Valve Removal/Installation........................................11-10.2
Breech Scavenger Check Valve Disassembly/Assembly ...................................11-10.4
Gun-Launcher Wiring Harness and Breech Limit Switches
Gun-Launcher Firing Mechanism Removal/Installation .........................................11-14
Gun-Launcher Breech Drive Motor Removal/Installation ......................................11-15
Gun-Launcher Breech Drive Solenoid Removal/Installation..................................11-16
Gun-Launcher Loading Tray Removal/Installation ................................................11-16
Gun-Launcher Loading Tray Disassembly/Assembly............................................11-17
Gun-Launcher Loading Tray and Ejector Adjustment............................................11-20
Gun-Launcher Loading Tray Guide and Ejector Cocking
Bracket Removal/Installation...........................................................................11-21
Gun-Launcher Ammunition Detent and Trigger Lever .......................................... 11-22
Gun-Launcher Obturator Seal Removal/Installation ..........................................11-24.3
11-2. Secondary Armament ............................................................................................11-25
Grenade Launcher M176.......................................................................................11-25
11-3. Sighting and Fire Control .......................................................................................11-28
Purging Laser Range Finder Units (M551A1 Only) ...............................................11-28
Synchronization of XM44 Series Periscope...........................................................11-33
M37 Loader’s Periscope Mount and Seal Removal/
Disassembly/Assembly/Installation .................................................................11-35
Driver’s M47/48 Periscope Mount and Seal Removal/
Installation .......................................................................................................11-36
Driver’s Periscope Washer, Pump, and Reservoir
M119 or M127 Telescope Removal/Installation.....................................................11-39
M149 or M165 Telescope Mount Removal/Installation........................................ .11-40
Inspection of Telescope Mount Bracket
Bolts ................................................................................................................11-40
M13A1C Elevation Quadrant Removal/Installation ............................................11-40.1
XM44 Series Periscope Body and Head Removal/installation ..........................11-40.2
Servicing XMI44 Series Emergency Periscope Battery.................................... 11-40.3
XM44 Series Periscope Washer, Pump, Reservoir and Blade
XM44 Series Periscope Linkage Removal/Installation .........................................11-42
CHAPTER 12 SPECIAL PURPOSE KITS
Section 12-1. General ....................................................................................................................12-1

12-2. Deleted
12-3. Deleted
12-4. Engine and Battery Winterization Kit .......................................................................12-1
12-5. Less Missile System Kit ...........................................................................................12-1
12-6. Mine Protective Kit ..................................................................................................12-2
12-7. Deleted
viii
C 10, TM 9-2350-;30-12
Page
CHAPTER 13 DESCRIPTION, OPERATION AND MAINTENANCE OF
7. 62MM MACHINE GUN M73E1
Section 13-1. Description and Data ...................................................................................................... 13-1
13-2. Operating Instructions..................................................................................................... 13-2
13-3. Maintenance Instructions................................................................................................ 13-4
13-4. Ammunition ..................................................................................................................... 13-8
13-5. Shipment and Limited Stowage and Demolition To Prevent
Enemy Use ..................................................................................................................... 13-8
APPENDIX I. REFERENCES ............................................................................................................... A-1
APPENDIX II. BASIC ISSUE ITEMS LIST
Section B-1. Introduction ..................................................................................................................... B-1

B-2. Basic Issue Items List ..................................................................................................... B-3
B-3. Maintenance and Operating Supplies............................................................................. B-15
APPENDIX II. MAINTENANCE ALLOCATION CHART

Section C-1. Introduction ..................................................................................................................... C-1
C-2. Maintenance Assignment .................................................................................................. C-3
C-3. Tool and Test Equipment .................................................................................................. C-24
INDEX....................................................................................................................................................... INDEX-1
(x Blank) ix
C11, TM 9-2350-230-12
CHAPTER 1
INTRODUCTION
Section 1-1. SCOPE, SECURITY CLASSIFICATION,

MAINTENANCE ALLOCATION, RECORDS, REPORTS, AND
EQUIPMENT SERVICEABILITY CRITERIA
1-1. Scope 1-4. Forms, Records, Reports, and Equipment

Serviceability Criteria
This manual contains operating and
organizational maintenance instructions for the a. Forms and Records. TM 38-750.
Armored Reconnaissance/Airborne Assault Vehicle: Full
Tracked, 152MM, M551. Other applicable publications b. Field Report of Accidents.
are referenced in Appendix I.
(1) Injury to personnel or damage to materiel.
1-2. Shillelagh Missile Subsystem Security AR385-40.
Classification.
(2) Ammunition accident or malfunction.
Commander’s responsibility and classification AR 75-1.
data TB 9-380-101.
c. Serviceability Criteria. TM 9-2350-230ESC.
1-2.1. Lubrication
d. Errors and Omissions. Report of errors,
Refer to LO 9-2350-230-12 for crew/operator omissions, and recommendations for improving this
lubrication instructions. publication by the individual user is encouraged. Reports
should be submitted on DA Form 2028 (Recommended
1-3. Maintenance Allocation Changes to Publications) and forwarded directly to
Commanding General, US Army Tank-Automotive
The maintenance allocation chart (Appendix III) Command, ATTN: AMSTA-MAPC, Warren, Michigan
allocates maintenance responsibilities. 48090
Section 1-2. DESCRIPTION AND DATA
1-5. Description bore and breech scavenging system to clear the
gun/launcher of residue and/or gases resulting from
The M551 (figures 1-1 and 1-2) is a light weight, firing. Later vehicles are equipped with the M81El
full tracked, deisel powered armored gun/launcher, which employs a compressed air closed-
reconnaissance/airborne assault vehicle. It is capable of breech scavenging system for the same purpose.
amphibious operation and can be transported and air-
dropped by heavy assault glider or cargo aircraft. 1-6. Tabulated Data
Armament consists of a 152MM gun/launcher mounted
to a 360-degree rotatable turret and capable of firing a. General
either conventional ammunition or guided missiles; a
7.82MM machine gun mounted coaxially with the Crew (1-commander, 1-driver,
gun/launcher; a cal. .50 machine gun mounted to the 1-loader, 1-gunner.............................................. 4
commander’s power assist cupola, which is capable of Weight Classification .................... No. 20 (Tons)
360-degree rotation; and eight fixed-mount grenade Weight, combat loaded ......................... 33,460 lb
launchers, four on each side of the turret. M551 vehicles Weight, curb (less fuel, crew,
equipped with M81 gun/launcher employ a CO2 and basic issue items) .......................... 28,525 lb
Weight, total air drop rate ............... 35,00 lb max
1-1
C9, TM 9-2350-230-12
Overall length ..................................... 248 in. (20ft 8 in.) Cooling system:

Overall width........................................ 110 in. (9 ft 2 in.) Capacity:
Overall height Dry........................................................ 44-1/2 qt
(over machine gun) .......................... 116 in. (9 ft 8 in.) Refill ............................................................32 qt
Freeboard (to top of hull) Antifreeze (-40°F. and above):
Static: Mixture with water................................................. 50%
Front ..................................................... -2-1/2 in. Type:
Rear.................................................... + 2-1/2 in. 6850-243-1992 ........................... 1 gal container
Moving: 6850-224-8730............................ 5 gal container
Front ......................................................... 1/2 in. Antifreeze
Rear........................................................ +1/2 in. (Arctic type)......................................... (-40° Fto-65°F):
Ground clearance.................................................. 19 in. Mixture ......................................................Full strength
Shipping cubic ................................................. 1831 cu ft Type, 6850-174-1806................................ 55 gal drum
b. Performance. Inhibitor (Above 80°F)
Mixture ...................................... 22-1/2 oz. per vehicle
Maximum speed (fourth range) ........................... 43 mph Type 6850-753-4967.................................... 6 oz. Can
Maximum speed (reverse) .................................... 9 mph d. Transmission - XTG-250-1A.
Maximum grade (ascending Steer Control:
or descending) ...................................................... 60% Land:
Maximum trench crossing width ................................ 7 ft Pivot steer .................................... First and both
Maximum range................................................373 miles ................................................... reverse ranges
Vehicle obstacle ability .......................................... 33 in. Geared steer ......................... Second, third, and
Minimum turning radius .......................................... Pivot ...................................................... fourth ranges
c. Engine 6V53T. Water:
Pivot steer ...............................All ranges except
Type .................................................................. Diesel ........................................................ fourth range
Compression ratio .................................................... 17:1 Oil Capacity:
Gross horsepower at 2800 rpm................................. 300 Dry ....................................................................56 qt
Fuel oil ...................................... Diesel: 40 cetane, Fed. Refill ....................................................................44 qt
............................................. VV- F- 800 or CITE Brakes ...............................................Multiple wet plate,
CAUTION: Use the following grades of fuel ............................................ mechanical-applied
oil at indicated temperatures: e. Electrical System.
Regular Grade0 Nominal voltage ..................................................... 24DC
(DF-2) (NATO F-54) .................................. 20° to +115°F Batteries .........................................................................4
................................................... (-7°C to +46°C)
f. Suspension.
Winter Grade (DF-1) ................................... 25° to +20°F
..................................................... (-32°C to 7°C) Torsion bar ......................................... Independent type
Arctic Grade Road wheels ........................................................10 dual
(DF-A) (NATO F-56)...................................... 25° to 65°F Size ..................................................................28 in.
................................................... (-32°C to 54°C) Track type .............................102 steel, rubber bushed
....................................................... pin-link shoe
NOTE. During certain emergency conditions, Width .............................................................17-1/2 in.
JP-5 aircraft turbine engine fuel may be used in
lieu of diesel fuel. g. Armament.
Fuel tank capacity (usable).................................. 158 gal Gun-Launcher, 152MM:

Fuel tank maximum Weight of gun-launcher ....................................10971b
acceptance rate....................... 50 gal per min. (avg.) Length .................................................................116in.
Fuel weight .............................................. 6.45 lb per gal Recoil (conventional ammunition)........................15 in.
Lubricating oil system capacity: Breech actuation.......................... Electrical or manual
Dry .................................................................... 21 qt ................................... separable sliding-rotating
Refill ...................................................... approx. 18 qt ................................................. breech chamber
1-2
C10, TM 9-2350-230-12
Breech chamber .......................... Left-hand 200 buttress Gunner’s aid dial:

threads .................................... 300 interruptions .................................. 0 to 50 mils right and
Firing method ...............................Electrical impulse only ......................... left numbered every 5 mils
Bore size .............................................152-mm (6 in.)
Tube rifling: Elevation Quadrant, M13A1C:
Length................................................... 95.65 in. Weight . .......................................................2. 06 lb
Depth of groove................................. 0. 050 in.
Width of groove ...................... 0. 245/0. 253 in. Individual weapons night vision sight, PVS2:
Width of land .................................... 0. 1434 in. Weight. .......................................................12. 7 lb
Number of grooves......................................... 48 Optical characteristics:
Twist ..............................1 turn in 41. 2 calibers Magnification .......................................4.0 power
Elevation ........................................................ 1.9 deg Field of view .......................................... 185 mils
Depression ......................................................... -8 deg Eyepiece focus............................+4 to4 diopters
Traverse ..................................... 360 deg right or left Objective lens focus 4 meters to infinity
Missile weight ..................................................... 58 lb ea Periscope, XM44 Series (gunner’s):
Conventional ammunition weight........................ 48 lb ea Weight ...................................................134-1/2 lb
Optical characteristics:
Machine gun, 7-62-mm, M73: High power system:
Weight ....................................................... 29.31 lb Magnification .................................................. 9X
Length ........................................................... 38 in. Field of view ...............................................6 deg
Rate of fire....................................450-500 rpm approx Unity power system:
Feed ........................................................ link belt Field of view ............................ 22 deg horizontal
Machine gun, 7. 62-mm, M219: .............................................. 8 deg vertical
Refer to paragraph 13-3 Line of sight travel .................... 22 deg elevation
Machine gun, Cal 50, M2, HB: ......................................18 deg depression
Weight 84 lb Temperature range
Weight of barrel.................................................... 28 lb (operable) ........................................... 65°F to +160°F
Length, overall.............................................. 65. 13 in.
Cyclic rate of fire ......................................450-500 rpm Periscope, M47, M48 (driver's):
Maximum effective range................................ 2000 yd Weight:
Grenade launcher .............................Fixed type, 8 tubes M47 (3)................................................. 29. 1 lb
g.1 Compressor Unit. M48 (infrared) ..........................................16.0 lb
Temperature range
Type ................................................reciprocating (operable)................................... 65°F to +125°F
Operating speed ...............................................3750 rpm Periscope, M37 (loader's):
Operating pressure............................................3000 psi Weight .........................................................14.5 lb
Lubricant (9150-753-4667) capacity: Optical characteristics:
Walter Kidde Field of view
(4310-460-2184)........................................ 4/5 pt (6 in. eye distance) ................ 50 deg horizontal
Bogue ............................................ 14 deg vertical
(4310-181-8895)........................................ 4/5 pt Line-of-sight .......................... one deg physically
Stewart Warner ......................................... two deg optically
(4310-196-1617) . ........................................ 1 pt Telescope, M119 (gunner's):
h. Sighting and Fire Control Instruments. Length, telescope. ...............................................41 in.
Azimuth indicator (10954720): Length, telescope in mount M149 . ................... .48 in.
Dial graduations: Weight, telescope .................................................37 lb
(100-mil) ..............................................0 to 3200 mils Weight, telescope and mount ...............................57 lb
.............................. right and left, numbered Operable temperature
............................................. every 200 mils range .......................................... 65° to +1250 F
(1-mil) ...............................................0 to 100 mils, Optical characteristics:
................................numbered every 5 mils Magnification .................................................. 8X
Weight ........................................................... 24 lb Field of view ...............................................8 deg
Height ............................................................ 12in. Reticle pattern,
Diameter. ............................................................. 7 in. conventional ammunition ................ballistic
1-3
C9,
C 9,TM
TM9-2350-230-12
9-2350-230-
Telescope, M127 (gunner’s):

Length, telescope.......................................... 41-1/4 in.
Magnification ................................................. 8X or12X
Field of view (8X) ................................................ 8 deg
(12X) ........................................ 5.333deg
Mount, Telescope, M149:

Length ................................................................. 28 in.
Width .................................................................... 10 in
Height .................................................................. 12 in.
Weight .................................................................. 20 lb
i. Missile Subsystem Units.
Optical transmitter .............................................. 34. 1 lb

Signal data converter............................................ 53.6 lb
Modulator ......................................................... 42.7 lb
Power supply ........................................................ 45.3 lb
Test checkout panel ............................................ 12.4 lb
Rate sensing unit. .................................................. 9.9 lb
Optical tracker ...................................................... 16.8 lb
1-4
C6, TM 9-2350-230-12
Figure 1-1. Armored reconnaissance/airborne assault vehicle: full tracked, 152MM, M551-left front view
1-4.2/(1-4.1 blank)
C6, TM 9-2350-230-12
Figure 1-2. Armored reconnaissance/airborne assault vehicle: full tracked, 152mm, M551- right rear view
1-5
C10, TM 9-2350-230-12
Section 1-3. SAFETY PRECAUTIONS
1-7. Vehicle 1-8. Turret and Cupola
CAUTION: To enter driver’s compartment by way of a. Make certain all personnel are clear of hull
open space between air compressor and rear air bottle, when traversing turret and that area is clear of obstacles.
manually traverse turret so gun launcher .is positioned
over rear deck. This method of entry prevents damage b. When traversing cupola, loader’s hatch
to stowed ammo in racks under gun/launcher. cover must be in fully opened or closed position and
turret area clear.
a. Be certain water steer lever is in LAND
position when driving vehicle on land to prevent damage 1-9. Sighting and Fire Control
to transmission and possible loss of vehicle control.
a. When XM44 Series periscope is not in use.
b. When raising or lowering driver’s seat, keep turn periscope ON/OFF switch to "OFF ". Place filter
body weight on seat. selector lever in "DARK"(XM44) or "OFF" (XM44E
Series) position to prevent damage to internal
c. Until driver becomes familiar with vehicle, components close ballistic cover.
every precaution must be taken not to overdrive or allow
loss of vehicle control. b. When operating night vision sight for cal.
.50 machine gun, keep eyeshield in contact with face to
d. When driving vehicle, make certain driver’s prevent emission of visible glow.
rotatable hatch cover is secured in the open or closed
position. c Do not look directly into searchlight beams.
Serious eye damage can result.
e. Do not leave vehicle with engine running.
d. Prior to installing new battery for XM44
f. If track is thrown while operating vehicle, do Series periscope, replace shipping plugs with vented
not apply brake. Allow vehicle to coast to stop. caps.
g. Make certain that vehicle is combat loaded e. Hazardous radiation conditions exist when
with equipment correctly stowed and secured when plastic dial window of azimuth indicator is broken or
swimming vehicle. removed. DO NOT TOUCH DIAL POINTERS.
h. Attach tow cable to front or rear tow 1-10. Armament

shackles when swimming vehicle to facilitate towing in
case of an emergency. a. Reject all HEAT warhead missiles that have
dented nose cones.
i. During vehicle swimming, if a solid stream
of water continues to emit from bilge pump outlets, b. Do not handle or move duds, except to
beach vehicle immediately. remove from weapon in a tactical situation. Under no
circumstances will a HEAT-T-MP or HE round be fired
j. Do not allow personnel between vehicles that has been allowed to remain in a hot gun-launcher
when slave starting. more than 5 minutes.
k The M8A3 air filter unit will not protect user c. Handle ammunition with care. Electric
against carbon monoxide. primers are sensitive to shock and high temperature.
l. With standard track, the vehicle is difficult d. Use only correct lots of ammunition and
to control on snow and ice. Use of arctic track will handle with care. Avoid striking fuze or primer.
improve vehicle control.
e. When operating winterization kit coolant
m. Inspection for spilled fuel should be made heater, turret must be positioned sot hat neither grenade
before and after operation and at halt in order to prevent launcher mount is over the heater exhaust outlet.
fires.
f. Do not smoke in crew compartment of
vehicle.
1-6
C10, TM 9-2350-230-12
g The check valve assembly in closed breech part of the tube, especially around the forcing
scavenging system should be cleaned at intervals not to cone and the breech cavity. Smoldering residue,
exceed 100 rounds. no matter how small, must be removed before
the next round is loaded.
CAUTION: Avoid damage to air cylinders, (2) When near maximum firing rate is required,
which are under very high pressure. inspect rear part of tube only. If smoldering
residue is observed, remove it and also inspect
h. Inspect detent hole and replace preformed and clear any smoldering residue from breech
packing of gun tube-to-detent housing seal every 40 cavity before loading the next round.
rounds. (3) When maximum firing rate is essential,
inspection for residue is not required.
i. If vehicle is not equipped with closed breech
scavenging system, missile firing causes a high n. When live round is chambered and breech
concentration of carbon monoxide in the crew closed, never turn blasting machine handle unless firing
compartment. Therefore, crew members should not be is intended. Blasting machine provides direct circuit
exposed to more than ten missile firings per day. Turret emergency fire capability to 152-mm gun/launcher.
blower must be on during missile firing to remove toxic
gases. o. Gun-launcher will fire despite loss of safe
to-fire and ready light indicators.
j The driver’s hatch must be closed for all
main gun firings. All crew members should be inside the 1-11. Grenades and Launchers
vehicle to prevent injury from muzzle blast of a
conventional round or, in the case of a missile firing in NOTE. Refer to TM 3-1330-203-10 for further safety
training with live warhead, to prevent possible fragment precautions.
spray from early ground impacts.
a. Since the vehicle is within range of
k. Flarebacks have occurred from firing fragments from the WP grenade M34, the crew should
missles when vehicle is not equipped with closed breech be inside the vehicle with the hatches secured in the
scavenging system. To reduce the hazard, the nylon closed position during firing.
and neoprene bags of a conventional round which is to
be fired following a missile firing should not be removed b. Check condition of grenades and launchers
until it is evident that a flareback did not occur. as soon as possible after vehicle is subjected to
attacking projectiles or shell fragments to make certain
l. Missiles should not be fired over friendly white phosphorous is not leaking onto the hull from
troops in training due to the hazard from early ground damaged grenade(s).
impacts.
m. The closed breech scavenging system has

been developed to remove smoldering residue from the
gun-launcher. However, when the vehicle is so
equipped, these precautions should be followed:
(1) When maximum firing rate is not required,

thoroughly inspect the rear
1-7
C5, TM 9-2350-230-12
Section 1-4. VEHICLE PERFORMANCE CHACTERISTICS
AND LIMITATIONS
Every type of Army equipment has certain may be necessary to check the air restriction indicator at
characteristics that are different from similar equipment. 30 minute intervals. If indicator is red, clean filter
Some of these characteristics are "signatures" that allow element. (Due to varying conditions resulting from
identification, while others merely impose operational geographical locations and other factors, commanders
limitations and/or operational guidance. Familiarity must establish the frequency of air cleaner service to
through practice and experience will result in controlling accommodate their peculiar environmental condition.)
these characteristics and avoid unnecessary problems.
Some of the AR/ AAV M551 characteristics and c. Operation of the vehicle in water
conditions under which they occur or are more necessitates observation of all precautions normally
pronounced have been included herein for training and required in the operation of waterborne vessels.
operational guidance.
Vehicle speed in still water is approximately 3.8 MPH
1-12. Automotive and maneuverability and control are good. In moving
water where the water speed approaches vehicle
a Under certain conditions, noise from the maximum speed, maneuverability and control are
engine turbocharger and the "rooster tail’ of exhaust substantially affected. Water operation requires special
smoke during vehicle acceleration will be more training as outlined in TM 21-306, Manual for the
noticeable. By comparison, the M551 total noise and Tracked Combat Vehicle Driver.
exhaust smoke, because of its smaller engine is much
less than larger track laying vehicles. The possibility of d. On early production vehicles (under serial
these conditions occurring are more probable when: number 140), the main gun, coaxial machine gun, and
grenade launchers should not be fired with the swimming
(1) Operating the vehicle before the engine has barrier erected due to the possibility of damage to the
warmed sufficiently. barrier. In later production, a quick release mechanism
for the whole forward surfboard/barrier system is
(2) Engine lacks power due to restricted air provided which, when released, allows firing of the main
induction system, leakage in the air induction gun or coaxial machine gun within a 90 degree sector to
system affecting the airfuel ratio, or other the direct front.
mechanical malfunction.
e. When operating in jungle or heavy
(3) Improper driving techniques such as lugging the underbrush, vegetation can clog the air intake grilles and
engine, fanning the accelerator pedal the radiator resulting in overheating and engine damage.
unnecessarily and/or applying instant thrust of Specific attention to cleaning at the halt and after daily
throttle pedal (floor boarding). operation will minimize the possibility of damage from
overheating. (If sudden overheating under combat
(4) Racing a free engine, throttle fanning, and conditions is experienced, use of a lower gear range or
operating in improper gear range will result in running engine for a few moments at idle speed may
more noticeable turbocharger whine. correct the condition.)
b. During operation under extremely dusty 1-13. Missile

conditions (zero visibility), the engine air cleaner may
clog within one hour and should be frequently checked a. Temperature changes may cause
and cleaned or replaced as necessary. Under such misalignment of the tracker. When temperature changes
extreme conditions, it in excess of 30OF occur, the tracker should be checked
and re-aligned as necessary.
b. Missile must not be fired when vehicle is in

motion because it cannot be controlled.
1-8
C5, TM 9-2350-230-12
1-14. 152MM Conventional Ammunition placement, and obscurity caused by smoke. Assistance
from a companion vehicle or other sources is
a. If smoldering residue is observed in the recommended.
gun-launcher, the following actions are recommended:
d. Cartridge, TP-T, XM411E3 is not ballistically
(1) Check closed breech scavenging system for matched with cartridge, HEAT-MP-T, XM409E5 and
proper functioning. therefore should not be used to zero the weapon for
firing cartridge XM409E5.
(2) Examine basic load of ammunition for moisture
absorption (softness) or other contamination of 1-15. Armament
the combustible cartridge case. Turn in soft or
contaminated rounds. Starting with full bottles of compressed air, and
with air compressor operating, there is enough
(3) Carefully inspect breech area for smoldering compressed air for 22 rounds when firing at the
residue after subsequent firings. If smoldering maximum rate.
residue recurs, turn in basic load for further
detailed inspection. 1-16. Night Fighting
b. The best estimate of emergency zero for Tracers from cal. .50 machine gun and main
telescope Ml19 is +5.0 mils elevation and +2.0 mils gun firing temporarily saturate gunner’s periscope XM44,
deflection. resulting in loss of vision.
c. Sensing at ranges less than 1000 meters is 1-17. Air Drop System
difficult due to firing shock, vehicle dis
The air drop system (35,000 lb) for this vehicle
has not completed service tests and is not available for
use. The current vehicle configuration has not been air
drop tested.
1-9
(1-10 Blank)
C8, TM 9-2350-230-12
CHAPTER 2
OPERATING INSTRUCTIONS
Section 2-1. SERVICE UPON RECEIPT OF MATERIEL
2-1. Deprocessing Vehicle and Break-In Services maintenance personnel are designated in the following
tables and illustrations.
a. Services upon receipt of materiel to be
performed by the crew and organizational b. Read the DD Form 1397 tag and follow all
precautions checked thereon.
TABLE 2-1. DEPROCESSING VEHICLE

STEP PROCEDURE FIG/ITEM
WARNING: Lift vehicle with lifting eyes on top of hull only. If

necessary unfasten shipping cover at each end of vehicle and roll
back until lifting eyes are exposed. Do not use tong lugs for
lifting vehicle.
1 Remove vehicle closure kit. 2-1

2 Remove Basic Issue Items saddle. 2-2
3 Remove ventilation screen assemblies from access openings on hull
bottom.
4 Drain fuel and inspect filters (table 2-1. 1).
5 Install plug assemblies (plug, preformed packing, screw and plate, 5-7
located in driver’s compartment) in hull access openings.
5.1 Remove preservative material from track adjuster piston and adjust 5-4
track before operating vehicle.
6 Install tow shackles (located in driver’s compartment) on tow lugs. 2-15
7 Remove cap or tape sealing engine exhaust outlet opening. 1-2/4
8 Remove plastic caps and/or tape from all openings leading to the 5-2/A
interior of the engine, including oil level indicator rod cap,
shroud opening, and oil filler caps.
9 Add electrolyte to batteries. Check that battery connections are 5-3/D
tight, and that polarity is correct as shown in figure 9-97. 9-97
CAUTION: Do not start engine or operate accessories with

auxiliary power until batteries are properly connected and elec-
trolyte added.
10 Remove cap or tape sealing turbocharger air Inlet. 5-2/A
2-1
C8, TM 9-2350-230-12
TABLE 2-1. DEPROCESSING VEHICLE - CONTINUED
11 Hold turbocharger fan stationary with 1/2 inch socket wrench on fan
hub nut. Start engine (table 2-3) and idle at 1500 RPM for 2
minutes. Stop engine, then remove socket wrench. (This step
is necessary to assure proper lubrication of turbocharger fan
bearing, if vehicle has not been operated for several months).
12 Install turbocharger air inlet hose and clamps (table 9-1).

13 Disassemble, clean, lubricate, and assemble cal.. 50 machine gun. 5-14
14 Install retracting slide assembly. 2-3
15 Check and adjust headspace and timing (tables 3-7 and 3-8).
16 Install flash hider and carrier assembly. 3-10, 3-13
CAUTION: Position carrier assembly in the 5 or 7 o’clock
position on barrel to prevent damage antenna when cupola is
traversed.
17 Install cal.. 50 machine gun spent brass ejection chute. 3-14
18 Install pintle support, cradle and pintle assembly, cal.. 50 machine 2-4
gun, and cupola traverse mechanism exterior wiring harness
and switch assembly.
19 Install turret stowage rack. 1-2/7
20 Remove protective materials from gun launcher, and traversing and
elevating servomotor fan outlets.
CAUTION: Thoroughly remove all preservative grease from 5-10. 2
interior of gun tube and breech mechanism. Lubricate according
to Table 5-8.1.
21 If vehicle is received with gun/launcher out of battery:
a. Wipe recoil sleeve with clean dry cloth to remove dirt or
dust.
b. Inspect sleeve for evidence of rust and/or pitting. If rusted
or pitted, notify support maintenance.
c. Wipe sleeve with clean cloth saturated with hydraulic oil
MIL-H-6083.
d. Close pressure bleed valve and use hand pump to return gun 3-2
to battery.
CAUTION: Keep hands and arms clear when pressurizing recoil
mechanism. Return to battery (:an be sudden and without notice.
2-2
C8, TM 9-2350-230-12
TABLE 2-1. DEPROCESSING VEHICLE CONTINUED
22 Recoil mechanism:
a. Check oil level in recoil mechanism with gun/launcher 3-2
elevated to 265 mils.
b. Pressurize recoil mechanism with hand pump until indicator 3-2
rod is in safe range.
23 Insure that recoil mechanism is exercised as prescribed in TB 9-
1000-234-35. (At time of deprocessing, recoil mechanism
should be exercised 20-25 times).
24 Operate and trim turret electric drive system Table 10-3.
25 Air compressor:
a. Check oil level in air compressor.
b. Turn air compressor on and charge cylinders.
c. Check for leaks in closed breech scavenging system hoses
and connections (use soap solution to check suspected areas).
d. Manually activate CBSS and check functional operation. 3-2. 3, 3-2. 4
e. Operate CBSS electrically:
(1) Turn turret power switch "ON" and turret selector Switch to "CONV". 3-2. 3
(2) Open CBSS air shut off valve. 3-2. 4
(3) Remove one mounting screw and loosen other screw of in-battery switch bracket
and swing up out of contact with actuator screw (see fig. 11-2). (M81E1 Gun Launcher).
NOTE. Do not disturb the setting of switch attachment to bracket
(4) To cycle CBSS, depress plunger of in-battery switch.
WARNING: When 1. 7-second surge of air is completed the breech chamber opens
automatically. All personnel must make certain to stand clear to prevent injury
(5) After completion of CBSS cycling SHUT OFF turret power, return in-battery
switch bracket to original position and replace and tighten mounting screws.
26 Check firing circuit using linear electromechanical actuator 4933-435-7736. 4-4
2-2.1
C8, TM 9-2350-230-12
TABLE 2-1. DEPROCESSING VEHICLE CONTINUED
27 Missile guidance system and fire control deprocessing should be

accomplished in accordance with separate instructions issued
by appropriate agency.
NOTE. For inspection and service of missiles, refer to table 7-2
28 Remove VCI bore tube from barrel of 7. 62MM machine gun and
clean barrel with clean dry patches.
29 Disassemble, clean, lubricate, and assemble 7. 62MM machine gun. 5-11, 5-12
Inspect for missing parts and proper assembly. LO 9-2350-
230-12
30 Install flash hider on 7. 62MM machine gun.
5-13
31 Install 7. 62MM machine gun in mount and connect solenoid lead.
3-7
32 Install spent brass ejection chute extension.
3-7
33 Remove protective lubricants and coverings from sighting and
fire control equipment.
34 Check air drop knobs (table 6-1, items 12 and 18).
35 Perform all "before operation" PM checks and services table 4-1.
36 Perform the following PM checks and services table 8-17:
Sequence numbers: 7. 1, 11, 12, 13; 16 through 27; 29, 33, 35;
39 through 43; 45 through 48; 52, 59.
37 Perform vehicle break-in services table 2-2.
2-2.2
C8, TM 9-2350-230-12
Figure 2-1. Removal/installation - vehicle closure kit
(2-2.4 Blank) 2-2.3

C4. TM 9-2350-230-12
TABLE 2-1.1. FUEL FILTER INSPECTION

STEP PROCEDURE REFERENCE
1 Completely drain fuel tanks to remove preservative, residual fuel, Table 5-4
and accumulated condensation.
2 Drain primary and secondary fuel filters Fig. 5-2
3 Remove primary fuel filter element and inspect for grease-like Fig. 9-17
substance.
CAUTION: Avoid damaging shell gasket.
4 a. If no evidence of contamination is found, reinstall element Fig. 9-17
b. If grease-like substance is present, clean filter shell with
fuel or solvent and install new filter - 2940-745-7730.
5 Close all fuel drains and fill tanks with specified fuel Par. 1-6c
REMOVAL PROCEDURE
1. REMOVE BASIC ISSUE ITEM BOXES
SECURED TO SHPPING SADDLE.
2. REMOVE TWO 2 SCREWS SECLUING
SADDLE TO AR INTAKE GRILLE.
3. REMOVE TWO 2 SCREWS SECURING
SADDLE TO ILOCKS ON ENGINE
COMPARTMENT ACCESS COVER.
4. REMOVE SADDLE AND REINSTALL SCREWS
ON ACCESS COVER.
5. SECURE AIR INTAKE GRILLE (STEP 2) WITH
2 SCREWS LOCATED IN DRIVER,S
COMPARTMENT.
6. SECURE SCREWS REMOVED IN STEP 2 TO
SADDLE AND STORE.
7. CHECK AND STOW SPARE PARTS AND
EQUIPMENT IN ACCORDANCE WITH BASIC
ISSUE ITEMS UST (A ENDIX 11).
Figure 2-2. (Superseded) Removal - basic issue (O.E.M.) items
2-3
TM 9-2350-230-12
Figure 2-3. Installation of retracting slide assembly on cal. .50 machine gun, M2, HB,
flex. type
2-4
TM 9-2350-230-12
Figure 2-4. Installation of pintle support, cradle and pintle assembly

and cupola traverse mechanism switch assembly
2-5
C1,TM 9-2350-230-12
TABLE 2-2. BREAK-IN SERVICES
DRIVE BELTS
1 Check tension of generator, fan, and coolant pump drive belts 5-2/A
Check vehicle for damage and loose attaching hardware.
NOTE. If vehicle is scheduled for storage in excess of

90 days, release tension on all drive belts, notify organiza-
tional maintenance personnel.
LUBRICATION
2 Check fuel and coolant levels Perform a complete suspension 5-2/A

lubrication (LO 9-2350-230-12), Appendix IV.
3 Check DD Form 1397 tag for engine and transmission oil viscosity 5-2/A
If tag states oil is of proper viscosity for local operation,
check the level (LO 9-2350-230-12) but do not change the
mil. OE10 may be added to PE1 or OE30 to PE2 to maintain
proper level in engine and transmission until first
scheduled change.
NOTE. Preservative engine oils PE1 and PE2 are identical
to engine oils OE10 and OE3S0, except that PE1 and AE2 have a
preservative additive. PE1 and PE2 will be used in the same
manner as the regularly used engine oil OE10 or OE30.
ROAD TEST
4 Drive 5 to 10 miles.
NOTE. If a vehicle w as driven to the using organization,
consider the mileage traveled as break-in mileage.
5 Observe all instruments and gages during road test 2-9
CAUTION: Do not engage in excessive speeds, accelerate
rapidly, or in any way load the engine or power train to
capacity during the break-in period.
6 Stop vehicle every mile and check for overheated hubs on road
wheels and idler wheels, and for lubricant leaks.
AFTER ROAD TEST
7 Upon completion of road test, perform after-operation preventive-

maintenance checks and services (table 4-1, steps 75 through 100) and
notify organizational maintenance to retorque air cleaner hose clamps.
CORRECTION OF EQUIPMENT FAULTS
8 Correct and report all equipment faults.
2-6
C8, TM 9-2350-230-12
Section 2-2. VEHICLE OPERATION
2.2. Operation Under Normal Conditions a. Special Driving Instruction. TM21-306.
The following tables and illustrations provide vehicle b. Cold Weather Starting. Figure 2-14, table 2-4.,1,
operating instructions. and TM 9-207. At -10’ F and below, four batteries are
required. If vehicle has only two, notify organizational
NOTE: Before operation the crew should be maintenance.
familiarized with the location and operation of all controls c. Extreme Hot and Cold Weather Operation.
and instruments (figs. 2-5 through 2-15). Continuously observe engine, transmission, and coolant
temperature warning lights (fig. 2-9).
2.3. Operation Under Unusual Conditions
TABLE 2-3. STARTING, DRIVING, AND STOPPING VEHICLE
PRE-STARTING INSTRUCTIONS
CAUTION: To enter driver’s compartment by way of open space

between air compressor and rear air bottle, manually traverse
turret so gun launcher is positioned over rear deck. This method
of entry prevents damage to stowed ammo in racks under gun/
launcher.
1 Perform before-operation preventive- maintenance checks and
services (table 4-1, steps 1 through 19).
2 Secure turret traverse lock 2-20/C
3 Make certain that missiles and ammunition are properly stowed 3-3
and secured in racks.
4 TURN OFF ALL COMMUNICATIONS AND ACCESSORY SWITCHES 2-19, 7-4
5 Install M48 periscope for driver’s night vision if required 2-7
6 Secure driver’s rotatable hatch cover in open or closed position 2-5/3, 13
7 Open both fuel tank valves 5-3/A
8 Make certain fixed fire extinguisher is charged and actuating 1-1/8, 2-6
handles are safety wired.
9 Stand by with portable fire extinguisher 2-18/A
10 Turn vehicle MASTER SWITCH on. MASTER SWITCH lamp will 2-10
illuminate.
11 Check driver’s periscopes washers and wipers 2-7
12 Check FUEL gage Add fuel if required Remove both filler caps 2-9
when refueling to vent entrapped air 5-3/C
CAUTION: Do not run vehicle completely out of fuel. Injectors
require full fuel return flow for cooling.
2-7
C4, TM 9-2350-230-12
TABLE 2-3. STARTING, DRIVING, AND STOPPING VEHICLE - Continued
STARTING ENGINE
13 Depress service brake pedal and pull out and up on parking BRAKE 2-5/6, 8
LOCK handle to set brake.
14 Place water steer lever in LAND position 2-6/F
WARNING: Be sure water steer lever is in LAND position to
prevent damage to transmission and possible loss of vehicle control.
15 Place transmission shift lever in N(neutral) position 2-6/F
CAUTION: Make certain that neutral safety switch roller con-
tacts transmission shift control lever near center of actuating end
when in N (neutral) position but is open in all other shift positions.
16 Turn SPEED/RPM indicator switch to RPM position 2-10
17 Make sure fuel shutoff knob is pushed in 2-6C
18 Press ENGINE STARTER switch to START position 2-10
CAUTION: Do not operate starter over 15 seconds. If engine
does not start, refer to troubleshooting procedure, table 5-1, steps
1 and 2. Allow 5 minute cooling-off period before again attempting
to start.
19 When engine starts, pull out hand throttle control knob and set to 2-6/E and
1500 rpm (fast idle) on tachometer indicator 2-9
CAUTION: During engine warm-up, refer to indicator panel 2-9
checkout procedure.
20 Turn SPEED/RPM indicator switch to SPEED position
2-10
DRIVING VEHICLE ON LAND
CAUTION: Until the driver becomes familiar with the vehicle,

every precaution must be taken not to over-drive or allow loss of
vehicle control. Make certain that gun is straight forward when
traveling through wooded areas to prevent damage to grenade pro-
jector mounts.
WARNING: Do not coast down grade. Keep engine speed matched
to vehicle speed to avoid losing steering capability.
21 Apply pressure on brake pedal, pull out and down on parking BRAKE 2-5/6,8
LOCK handle to release brake.
22 With brake pedal depressed, hand throttle control knob pushed in, 2-6/F
shift from N (neutral) to desired range.
23 Release brake pedal and depress accelerator pedal to attain desired 2-5/8, 19
vehicle speed.
2-8
C8, TM 9-2350-230-12
TABLE 2-3. STARTING, DRIVING, AND STOPPING VEHICLE - Continued
2-8.1
TM 9-2350-230-12
TABLE 2-3. STARTING! DRIVING, AND STOPPING VEHICLE - Continued
DRIVING VEHICLE ON LAND - Continued
27 Perform during-operation preventive-maintenance checks and

services if tactical situation permits (table 4-1, steps 64 through 67).
NOTE In case of emergency, driver can escape by his escape 2-6/A and
hatch or through the turret by pulling pin safety clip chains securipg 2/27
vertical ammo rack and screens to turret ring.
STOPPING VEHICLE AND ENGINE
28 Release accelerator pedal, depress brake pedal, and stop vehicle 2-5/8, 19
29 With brake pedal depressed, position transmission shift lever in N 2-5/6, 8, 14
(neutral) position, pull out and up on parking BRAKE LOCK handle
to lock brake.
30 Turn SPEED/RPM indicator switch to RPM position 2-10
31 Set hand throttle control knob to run engine at 1000 - 1300 rpm on 2-5/17
tachometer indicator for 3 to 5 minutes and 2-9
32 Push hand throttle control knob in to return engine to normal 2-5/17
idle speed.
33 Turn radio and all accessories off 2-19, 7-4
34 Pull out on engine FUEL SHUT-OFF control handle to stop engine 2-6/C
CAUTION: Do not apply excessive pull on handle when stopping
engine.
NOTE If FUEL SHUT-OFF valve does not operate properly, 5-2/C
open engine exhaust grille and disconnect fuel line at primary fuel
filter.
35 Turn vehicle MASTER SWITCH off 2-10
36 Perform after-operation preventive-maintenance checks and services
(table 4-1, steps 74 through 100).
2-8.2
TM 9-2350-230-12
Figure 2-5. Driver’s compartment
2-9
C8,TM 9-2350-230-12
Figure 2-6. Driver’s miscellaneous controls
2-10
TM 9-2350-230-12
Figure 2-6.1. Removal/installation - driver’s steel escape hatch cover.

2-10.1
C10, TM 9-2350-230-12
Figure 2-6.2. Driver’s rotatable hatch emergency outside latch release and
open position latch stop
2-10.2
C10, TM 9-2350-230-12
Figure 2-7. Installation and operation of driver’s M48 periscope

(2-12 Blank) 2-11
TM 9-2350-230-12
Figure 2-8. Vehicle driving lights chart

2-13
C6, TM 9-2350-230-12
1. ENGINE COOLANT TEMPERATURE GAGE. TEMPERATURE GAGE SHOULD NORMALLY READ 175’210’F.
2. ENGINE COOLANT TEMPERATURE WARNING LIGHT. WARNING LIGHT WILL COME ON IF ENGINE
TEMPERATURE REACHES 225"F (CHECK AGAINST ENGINE COOLANT TEMPERATURE GAGE). STOP
ENGINE AND CHECK FOR:
a. LOW COOLANT LEVEL IN SURGE TANK--FILL SYSTEM.
b. DEBRIS ON INTAKE GRILLE OR RADIATOR-REMOVE DEBRIS.
c. BROKEN COOLANT PUMP BELTS--NOTIFY ORGANIZATIONAL MAINTENANCE.
IF, AND ONLY IF NONE OF THE ABOVE PROBLEMS ARE FOUND, LOCK COOLANT FAN CLUTCH IN
DIRECT DRIVE (B, FIGURE 5-2) FCR EMERGENCY OPERATION. NOTIFY ORGANIZATIONAL
MAINTENANCE.
3. ENGINE LOW OIL PRESSURE WARNING LIGHT. IF WARNING LIGHT REMAINS ON AT 1300 RPM,
INDICATING LESS THAN 9-13 PSI PRESSURE, STOP ENGINE AND CHECK OIL LEVEL. IF OIL IS AT
PROPER LEVEL, NOTIFY ORGANIZATIONAL MAINTENANCE.
4. TRANSMISSION LOW OIL PRESSURE WARN ING LIGHT. IF WARNING LIG HT REMAI NS ON AT 1500 RPM,
INDICATING LESS THAN 4-8 PSI PRESSURE, STOP ENGINE AND CHECK OIL LEVEL. IF OIL LEVEL IS
CORRECT, NOTIFY ORGANIZATIONAL MAINTENANCE.
5. TRANSMISSION OIL TEMPERATURE WARNING LIGHT. WARNING LIGHT INDICATES OVERHEATED

IIANSMISSION. PLACE SHIFT SELECTOR IN NEUTRAL POSITION AND IDLE AT 1300 RPM FOR THREE
MINUTES. IF LIGHT REMAINS ON, NOTIFY ORGANIZATIONAL MAINTENANCE.
WE 12036
Figure 2-9. Driver’s indicator panel
2-14
C10, TM 9-2350-230-12
Figure 2-10. Driver’s switch panel
TABLE 2-4. AMPHIBIOUS OPERATION

PREPARING VEHICLE FOR AMPHIBIOUS OPERATION

1 Perform before-operation preventive-maintenance checks and services
WARNING: The crew should be thoroughly trained on procedures
for evacuating the vehicle in water prior to amphibious operation.
CAUTION: 1. Vehicle must be combat loaded with equipment App. II
correctly stowed and secured to achieve proper balance in water 1-1/25 &
2. Attach tow cable to front or rear towing shackles to 1-2/22, 23
facilitate towing in case of power failure. Secure center portion of
cable to vehicle to prevent drag or entanglement.
2 Be sure driver’s escape hatch and drain/access plugs on hull bottom 2-6/A, and
are secured. On vehicles equipped with exhaust plume diffuser, pull 5-7
pin and turn diffuser upside down (off the exhaust outlet) whenever
vehicle is to be operated with barrier erected.
3 Erect and secure surfboard and barrier. Make certain surfboard cavity 2-11, 12,
drain cover is in place. Remove covers from front bilge pump outlets & 2-12. 1
CAUTION: Traverse gun-launcher approximately 90 mils to the
left of driver’s hatch cover, prior to swimming, so driver will have
additional clearance in evacuating vehicle if necessary.
2-15
C6, TM 9-2350-230-12
TABLE 2-4. AMPHIBIOUS OPERATION - CONTINUED
PREPARING VEHICLE FOR AMPHIBIOUS OPERATION - Continued

4 Turn vehicle MASTER SWITCH and BILGE PUMP switches on; listen 2-10 and
and make certain bilge pumps are operating properly. Turn BILGE 2-13
PUMP switches off and start engine.
ENTERING WATER
5 Push water steer lever forward to WATER position 2-6/F

6 Place transmission shift lever in 1st (low) position 2-6/F
WATER ENTRY CAUTIONS
CAUTION: 1. Select a gradual sloping bank of firm ground that is

free of rocks, stumps, or debris to enter water. Avoid drop offs into
water, soft ground or steep grades where vehicle may lose traction
and mire down or skid.
2. Leave vehicle hatch covers open during water entry
and operation if situation permits.
3. 10 mph is maximum safe water entry speed from
slopes up to 15% (1.5 ft. drop in 10 feet).
4. 5 mph is maximum entry speed on slopes of 15 to 30%.
5. The vehicle should be eased into the water slowly
from slopes of over 30%. The vehicle front will become buoyant
before entry is completed.
6. Avoid steep entry slopes if at all possible. High
speed entries from steep slopes not only can cause failure of flotation
components, but also endanger the vehicle’s personnel.
NOTE. Entry technique must be controlled by good driver judge-
ment. This can result only from adequate training and experience.
7 Immediately upon entering water, turn BILGE PUMP switches on and shift 2-10 and
to 3rd range for maximum performance 2-6/F
WARNING: During water entry and vehicle swimming, if a solid 2-12/F, G
stream of water continues to emit from bilge pump outlets, the vehicle
should be beached immediately and the cause of leakage determined.
8 When turning vehicle, return steer bar to center position before turn is 2-5/4
completed, allowing momentum of vehicle to complete turn. To obtain
maximum turning response, decelerate, turn steering bar,
then accelerate.
NOTE. Propulsion and steering are same on water and land.
CAUTION: 1. If engine becomes inoperative during amphibious

operation, the crew should prepare to evacuate vehicle.
2. If it becomes necessary to tow vehicle while in water,
towing speed should not exceed 5 mph.
2-16
C10, TM 9-2350-230-12
TABLE 2-4. AMPHIBIOUS OPERATION - CONTINUED
STOPPING THE VEHICLE IN WATER
9 Release accelerator pedal and apply brake to stop tracks 2-5/8, 19

10 Move transmission shift lever to R2 (reverse) position. Release brake 2-6/F
and gently accelerate.
NOTE. Vehicle should be stopped when traveling in reverse in same
manner, except shift lever is moved to 1st (ow) position.
11 Release accelerator pedal when forward motion of vehicle is stopped; 2-5/14, 19
move transmission shift lever to N (neutral) position.
LEAVING WATER
12 Approach bank squarely, ease up on accelerator pedal to reduce track 2-5/19

speed allowing vehicle to coast until tracks. contact solid ground.
13 Return water steer lever to LAND position and proceed to land in 1st 2-6/F
(low) range.
CAUTION: Leave water on hard ground, free of obstacles. Avoid
mushy banks or steep slopes where vehicle may mire or stall.
14 Stop vehicle when clear of water and on firm footing. Clear tracks and
wheels of any debris.
15 Turn bilge pumps off when all water has been removed from vehicle and 2-13
stop engine. When required, driver’s escape hatch may be loosened
sufficiently to break seal and allow residual water to drain from
vehicle.
15. 1 Install front bilge pump outlet covers 2-12. 1
16 Retract surfboard and barrier 2-11, 12,
& 2-12. 1
WARNING: Pull hands clear immediately after releasing quick-
release surfboard, effective vehicle serial no. 70.
17 Inspect suspension components and any other vehicle components,
which may have been immersed or sprayed while swimming vehicle,
for water contamination. Service according to LO 9-2350-230-12.
CAUTION: If vehicle has been submerged, retrieve vehicle,
remove hull access plugs and driver’s escape hatch, and
immediately evacuate vehicle to appropriate supporting main-
tenance area for servicing, prior to any operation of vehicle
components.
2-17
C2, TM 9-2350-230-12
Figure 2-11. Erecting flotation surfboard and barrier (through vehicle serial no. 69)
(1 of 2)
2-18
C2, TM 9-2350-230-12
Figure 2-12. Erecting flotation surfboard and barrier (through vehicle serial no. 69) (2 of 2)
2-19
C10, TM 9-2350-230-12
Figure 2-12.1. Erecting surfboard and barrier (effective vehicle serial no. 70)
2-20
C4, TM 9-2350-230-12
Figure 2-13. (Superseded) Operation of bilge pumps
2-20.1
C4, TM 9-2350-230-12
TABLE 2-4.1. COLD WEATHER STARTING PROCEDURE (REFER TO FIGURE 2-14)
NOTE. Steps marked with asterisk (*) are applicable only to vehicles with
hand pump lock and air box flame heater fuel shutoff valve
(B, figure 2-14). All other steps are applicable to all vehicles.
PREPARATION FOR STARTING
1 Traverse turret to the side and open engine compartment right exhaust grille. 1-2
*2 Open air box flame heater fuel shutoff valve. 2-14B
3 Check air box flame heater accumulator pressure gage. Pressure indicator 2-14
should be in cold start area of gage. If not, use accumulator hand pump to
increase pressure:
*a. Release accumulator hand pump lock.
b. Turn pump handle to release from detent, and actuate handle
to increase pressure.
4 After attaining required pressure, rotate pump handle to engage detent.
*5 Position hand pump lock to locked position.
6 Close engine compartment exhaust grille.
STARTING
7 Place transmission shift lever in "N" (neutral) position. 2-6E
8 Turn vehicle master switch ON. 2-10
9 Turn speed/RPM indicator switch to RPM. 2-10
NOTE. If engine coolant heater has been operation, proceed to step 11.
10 Pull out on fuel shutoff control knob, hold starter switch in START, and 2-6C
hold air box flame heater switch to ON position for 15 to 20 seconds. 2-10
11 Push in fuel control shutoff knob, continue to hold starter switch in START,
and cycle flame heater switch on and off 1 or 2 times per second, with a
2 second pause in the OFF position every 7 to 10 seconds until engine
reaches 400 to 500 RPM, then depress accelerator half way and disengage
starter switch.
NOTE. If engine does not commence firing after a total of 40 seconds of
cranking or if the indication of cylinder firing ceases for a
period of over 10 seconds, stop cranking and check the air box
flame heater system components for proper operation. If a
malfunction is evident, notify organizational maintenance personnel.
12 With brakes locked, move transmission shift lever to 4th position and 2-9
continue operation of the engine at 1200-1500 RPM until coolant temperature
gage indicates 120° to 140°F. If transmission high temperature warning
light illuminates, shift to "N" (neutral) and idle at 1200-1500 RPM until
light goes out.
*13 Reopen right exhaust grille and close flame heater fuel shutoff valve.
Close grille.
RECHARGING ACCUMULATOR
NOTE. When through with vehicle operation for the day, reopen right
exhaust grille. Recharge accumulator as follows:
*14 Open flame heater fuel shutoff valve.
*15 Move hand pump lock to unlocked position.
16 Release hand pump from detent position.
17 Run engine is neutral at approximately 2000 RPM until no further increase
in pressure is apparent on accumulator pressure gage.
18 Return hand pump to detent position.
*19 Move hand pump lock to locked position.
*20 Close flame heater fuel shutoff valve.
21 Close exhaust grille.
2-20.2
C4, TM 9-2350-230-12
Figure 2-14. Cold weather starting
Figure 2-14.1. Deleted.
2-21
C9, TM 9-2350-230-12
TABLE 2-5. TOWING DISABLED VEHICLE AND TOWING OR SUPPLYING AUXILIARY
POWER TO START ENGINE
TOWING DISABLED VEHICLE ON LAND

1 Remove sprocket drive shafts if transmission has sustained damage.
Notify organizational maintenance personnel.
2 Connect tow bar or tow cables. 2-15
WARNING: If drive shafts have been removed use tow bar only,
since vehicle has no steering or braking capability.
3 Place transmission shift lever in N (neutral) position. 2-6/F

4 Release brake and signal towing vehicle. 2-5/8
WARNING: When towing disabled vehicle, limit speed to 5 MPH

if tactical situation permits. NEVER ATTEMPT TO TURN AT
SPEED EXCEEDING 5 MPH.
NOTE. In an emergency, vehicle may be towed in reverse direction

for a distance not to exceed 1/4 mile at a speed not to exceed 5 mph in
N (neutral) range. If vehicle towing distance is greater than 1/4 mile,
notify organizational maintenance to remove sprocket drive shafts.
TOWING VEHICLE TO START ENGINE
1 Connect tow bar or tow cables 2-15

2 Place transmission shift lever in 2nd gear range 2-6/F
3 Turn vehicle MASTER SWITCH on. 2-10
4 Place water steer lever in LAND position. 2-6/F
5 Depress brake pedal and release parking BRAKE LOCK handle. 2-5/6, 8
WARNING: Never attempt turns at speeds exceeding 5 MPH.
6 Choose terrain where vehicle can be towed without turning, and tow
6 to 19 MPH as required for starting.
CAUTION: Do not depress accelerator pedal on towed vehicle.

7 After engine starts, move transmission shift lever to N (neutral) position 2-6/E, F
and adjust hand throttle control knob to run engine at fast idle.
8 Disconnect towing vehicle.
USING AUXILIARY POWER TO START ENGINE
1 Connect auxiliary power (slave) cable to stalled vehicle auxiliary power 2-6/C
receptacle and to auxiliary vehicle or other power source.
CAUTION: 1. Polarity and voltage (24v) must be identical in

both vehicles. 2-10
2. Be sure vehicle MASTER SWITCH is off in stalled
vehicle. All accessories must be off.
3. Do not allow personnel in between vehicles during
slave start operation.
4. Place transmission shift lever in neutral position
and set parking brake on both vehicles.
2-22
C8, TM 9-2350-230-12
TABLE 2-5. TOWING DISABLED VEHICLE AND TOWING OR SUPPLYING AUXILIARY
POWER TO START ENGINE - CONTINUED
USING AUXILIARY POWER TO START ENGINE - Continued

2 Start auxiliary vehicle engine or auxiliary generator and adjust
throttle. When using M551 vehicle for auxiliary power (slave
starting source) adjust throttle control knob to indicate 1300
to 1500 RPM on tachometer indicator prior to cranking stalled
vehicle. Do not accelerate engine during slave start. Engine
speed will decrease and battery-generator indicator will
normally drop into yellow or red band during slave starting.
3 Press stalled vehicle ENGINE STARTER switch to start engine.
Follow applicable starting procedure (table 2-3, or figure
2-14 and table 2-4. 1).
4 Increase engine rpm in receiving vehicle when engine has started.
5 Disconnect auxiliary power cable and quickly turn on vehicle MASTER 2-10
SWITCH.
Figure 2-15. Installation of tow shackles, tow pintle, tow cables or tow bar
2-23
C8, TM 9-2350-230-12
Section 2-3. OPERATION OF AUXILIARY EQUIPMENT
2-4. Operation Instructions
The following tables and illustrations pro-

vide auxiliary equipment operating instruc-
tions.
TABLE 2-6. OPERATION OF MBA3 AIR FILTER UNIT

BEFORE OPERATION
NOTE. The MBA3 air filter unit is used in connection with a tank
protective mask for protection against toxic gases and in extremely
dusty conditions to remove dust from air breathed by crew members.
WARNING: 1. In toxic gas attack, don mask immediately before
beginning operation of filter unit.
2. The air filter unit will not protect user against car-
bon monoxide.
3. Do not supply air from filter unit to masks when
vehicle interior is below +20 degrees. Injury to user’s lungs may
result.

(table 4-1, step 43).
2 Unstrap carriers from stowed positions and remove masks. 2-16/1,2
3 Don masks and adjust face pieces.
4 Remove commander’s, gunner’s, and loader’s air purifier-to-canister 2-16/4
hoses from stowage bag.
5 Remove driver’s air purifier-to-canister hose from spring clips and 2-16/8,9
connect to canister.
NOTE. If the air filter unit is to be used by fewer than four persons, 2-16/11
disconnect the unused hose from the air purifier. Cover the unused
outlet or outlets on the air purifier with air flow control caps. When
only three outlets are used, the fourth outlet is covered with an air-
flow control cap without a center hole. When less than three outlets
are used, one of the holes is covered with an airflow control cap with-
out a center hole and the other outlets are covered with airflow control
caps with center holes.
6 Remove spring clip from air purifier housing. 2-16/12

7 Remove caps from air purifier and connect commander’s, gunner’s, and 2-16/11
loader’s air purifier-to-canister hoses.
8 Turn on air filter unit with rheostat knob located on loader’s control 3-1/A
box, and increase to maximum airflow. If excessive airflow around
face piece causes discomfort, reduce the flow accordingly with
rheostat knob.
AFTER OPERATION
9 Remove masks, place in carriers and stow. 2-16/1,5

10 Turn air filter unit COMPLETELY OFF (rheostat knob counterclockwise). 3-1/A
11 Uncouple commander’s, gunner’s, and loader’s air purifier-to-canister 2-16/4, 6
hoses and place in stowage bag.
2-24
TM 9-2350-230-12
TABLE 2-6. OPERATION OF M8A3 AIR FILTER UNIT - CONTINUED
AFTER OPERATION- Continued
12 Stow driver’s air purifier-to-canister hose in spring clips. 2-16/8, 9

13 Fasten spring clip over holes in air purifier housing. 2-16/12
PROTECTIVE LIFE OF GAS FILTERS
Record the duration of each chemical attack and the type of agent used.
With this record, the protective life of the M12A1 gas filter can be com-
puted using the following information. The operator will notify organi-
zational maintenance personnel to replace the gas filter when 100 replace-
ment units have been used.
GAS FILTER REPLACEMENT UNITS
Type Of Attack
Each air CX and all
Ground- delivered nerve other agents
Duration delivered agent attack and including
of nerve all blister agent CK unidentified
attack agents attacks except (units agents (units
(min) (units used) CX (units used) used) used)
2 1/2 1 10 6
4 1 2 20 12
6 1-1/2 3 30 18
8 2 4 40 24
10 2-1/2 5 50 30
12 3 6 60 36
14 3-1/2 7 70 42
16 4 8 80 48
18 4-1/2 9 90 54
20 5 10 100 60
An attack lasting less than 2 minutes is considered to have a duration

of 2 minutes. An attack lasting longer than 2 minutes but less than 4
minutes is considered to have a duration of 4 minutes. Similar consider-
ation is given to attacks up to 20 minutes.
To calculate the number of units used in an attack longer than 20

minutes, the following formula may be used: Multiply the duration
(number of minutes) by the number of units shown on line 1 of the
appropriate attack column and divide by 2. For example, a filter
exposed to a 30-minute air-delivered nerve agent attack would use 15
replacement units, as follows:
30 minutes x 1 unit = 15 units
2
2-25
TM 9-2350-230-12
Figure 2-16. M8A3 air filter unit
2-26
C3, TM9-2350-230-12
Figure 2-17. Operation of personnel heater
2-27
C10, TM 9-2350-230-12
Figure 2-18. Operation of portable, fixed (engine compartment),

and crew compartment fire extinguishers
2-28
C3, TM 9-2350-230-12
Section 2-4. OPERATION OF TURRET AND CUPOLA
2-5. Turret and Cupola Operation Instructions mechanical, stop at rear deck. To continue traversing,
a. General. The following tables and illustrations elevate the gun-launcher to clear the stop.
provide turret and cupola operating instructions.
c. Non-Stabilized Mode. When vehicle MASTER
NOTE. Before operation, the crew should be familiar SWITCH and TURRET CONTROL POWER switch are
with the location and operation of all controls and turned on, the electric drive control system is in non-
instruments (figs. 2-19 through 2-22). stabilized mode. When either gunner’s or commander’s
control handle palm switch is depressed, the weapon
b. Electric Drive Control System. The electric drive and turret will respond to deflection of the control handle
control system provides controlled power for traversing and elevate, depress, or traverse at a rate dependent on
the turret and elevating and depressing the weapon in degree of deflection.
either nonstabilized or stabilized modes. An electrical
interlock is provided in the turret control switch circuit to d. Stabilized Mode. When vehicle MASTER
prevent accidental operation of turret and weapon. if SWITCH, TURRET CONTROL POWER and STAB
TURRET CONTROL POWER switch has been turned switches are turned on and with either control handle
on prior to vehicle MASTER SWITCH, the system will not palm switch depressed, the electric drive control system
function until the TURRET CONTROL POWER switch is is in stabilized mode and immediately becomes oriented
turned off and then on again. The gun-launcher can be in space at a fixed elevation and traverse attitude with
elevated to 336 mils (19 degrees). Depression is limited vehicle moving over rough terrain. The gunner must still
to 142 mils (8 degrees) over the front and sides of aim, track, and fire using traversing and elevating
vehicle and 56.8 mils depression over rear deck. When controls in usual manner, but has an advantage in that
power traversing the turret and gun-launcher is below he is effectively firing from a stable space platform
58.8 mils depression, the gun-launcher will automatically relatively undisturbed by vehicle pitch and roll. The
elevate to clear the rear deck. weapon and sight will remain stabilized in space as long
as gunner's or commander’s palm switch is depressed.
CAUTION: To prevent damage to electric drive The control handles will move the weapon and turret at
system, do not hold control handle in maximum elevation precisely controlled rates as in non-stabilized mode.
or depression position when gun-launcher contacts When control handles are centered, weapon and turret
mechanical stop. In manual traverse, the turret will will again become oriented at elevation and traverse
contact a attitude relative to space that exists when the controls
are neutralized.
TABLE 2-7. OPERATION OF TURRET

BEFORE OPERATION
1 Perform before-operation preventive-maintenance checks and
services (table 4-1, steps 20 and 31 through 44).
2 Make certain all personnel are clear of turret. Engine compartment

grilles, and battery and air cleaner access doors and covers 1-2/3, 5, 6,
must be closed. 16
3 Release turret traverse lock. 2-20/C
4 Turn vehicle MASTER SWITCH on, and start engine. Engine must
be operating at 750 RPM to maintain voltage during operation. 2-10
2-29
C8, TM 9-2350-230-12
TABLE 2-7. OPERATION OF TURRET - Continued
BEFORE OPERATION - Continued

CAUTION: To enter driver’s compartment by way of open space
between air compressor and rear air bottle, manually traverse
turret so gun launcher is positioned over rear deck. This method
of entry prevents damage to stowed ammo in racks under gun/
launcher.
NOTE. Vehicle MASTER SWITCH must also be on when

auxiliary power is supplied to operate turret.
5 Make sure TURRET CONTROL POWER and STAB switches are of f 2-19
and FIRE CONTROL selector is in OFF position.
MANUAL OPERATION
6 Depress adjustment lever and move gunner’s power control handle 2-19
to lowered position.
7 Release manual elevation handwheel by pulling up locking pin and 2-19

elevate or depress gun-launcher.
8 Traverse turret with manual traverse handle. 2-19
ELECTRICAL OPERATION (NON-STABILIZED MODE)
6A Secure manual elevation handwheel by engaging locking pin in 2-19

retainer. Depress adjustment lever and move gunner’s power
control handle to raised position.
7A Turn TURRET CONTROL POWER switch on. The indicator lamp 2-19
above the switch will illuminate.
NOTE. Allow approximately 20 seconds until TURRET 2-19

CONTROL POWER switch READY lamp illuminates.
8A Depress palm switch on power control handle and remove any gun 2-19 and
elevation or turret azimuth drift by rotating TRAV and/or ELEV 2-21/7, 8,
trim buttons. Rotate gunner’s control handle to elevate or 11
depress gun and to traverse turret onto target.
CAUTION: DO NOT KEEP HANDLE IN ELEVATION OR

DEPRESSION POSITION WHEN MECHANICAL STOP IS REACHED.
Immediately return handle to neutral position or back away from
stop. A stalled servo motor (recognizable by high pitched sound,
and/or burning odor from motor generator) will cause severe
damage to servo motor and motor generator.
NOTE. Commander can override gunner’s control in either 2-21/6, 11

non-stabilized or stabilized modes by depressing his palm switch
and rotating control handle.
2-30
TM 9-2350-230-12
TABLE 2-7. OPERATION OF TURRET - Continued
ELECTRICAL OPERATION (STABILIZED MODE)
6B Follow steps 6A through 8A above.
7B Turn TURRET CONTROL STAB switch on. The indicator lamp will 2-19
illuminate.
8B Continue squeezing gunner’s control handle palm switch. Gun- 2-19

launcher will automatically remain parallel to initial line of
sight in elevation and azimuth while tracking vehicle is moving.
NOTE. Gunner must make corrections in elevation due to the

rise or fall of terrain and azimuth corrections due to vehicle
horizontal movement.
AFTER OPERATION
9 Turn TURRET CONTROL STAB and POWER switches off. 2-19
Indicator lamps will go out.
10 Secure turret traverse lock. 2-20/C
11 Perform after-operation preventive-maintenance checks and

services, table 4-1, steps 101 and 109 through 118).
(2-30.2 Blank) 2-30.1

C9, TM 9-2350-230-12
Figure 2-19. Gunner’s controls and instruments
2-31
C6. TM 9-2350-230-12
Figure 2-20. Turret miscellaneous controls

(through vehicle S/N 699)
2-32
C6, TM 9-2350-230-12
Figure 2-20.1. Dual position mounting of commander’s control handle.
2-32.1
C9; TM 9-2350-230-12
Figure 2-20.2. Commander’s ballistic shield plate assemblies
2-32.2
C 1, TM 9-2350-230-12
TABLE 2-8. OPERATION OF CUPOLA
BEFORE OPERATION
(table 4-1, steps 29 and 30).
2 Engage machine gun in travel lock. 3-14
WARNING: Make certain all personnel are clear of turret roof and 2-20/D
loader’s hatch cover is secured open or closed.
ELECTRICAL OPERATION (INSIDE OF CUPOLA)
4 Turn cupola control assembly POWER switch to ON position. 2-21/3
CAUTION: 1. Make certain cupola manual traverse handle is 2-22/1

down in stowed position clip.
2. Maximum operation of power cupola is 2 minutes on
and 10 minutes off to prevent damage to traverse
motor.
NOTE. 1. Safety switch will not permit cupola electrical operation 2-22/B
with cupola manual traverse handle engaged.
2. Cupola brake is automatically released when operating
cupola electrically.
5 Press cupola control assembly ROTATION switch to the traverse LEFT 2-21/3
or RIGHT position. Release switch to stop rotation.
ELECTRICAL OPERATION (OUTSIDE OF CUPOLA)
4A Follow step 4 above.

5A Press control button attached to cal. .50 machine gun left-hand grip to 2-4
traverse cupola left; press right-hand grip control button to traverse
cupola right. Release control button to stop rotation.
MANUAL OPERATION (EMERGENCY USE) 2-22
AFTER OPERATION
6 Turn cupola control assembly POWER switch to OFF position. 2-21/3

7 Perform after-operation preventive-maintenance checks and services,
2-33
TM 9-2350-230-12
Figure 2-21. Commander’s power assist cupola controls
2-34
C9, TM 9-2350-230-12
Figure 2-22. Manual operation of commander’s power assist cupola
Section 2-5. OPERATION OF SIGHTING AND FIRE CONTROL

AND ARMAMENT BORESIGHT PROCEDURE
2-6. Operation Instructions. an articulated joint so that the eyepiece is made

conveniently available to the gunner throughout the
a. General. The following tables and illustrations range of gun elevation and depression. A dioptral
provide sighting and fire control operating and armament adjustment is provided to accommodate focal variations
boresight instructions. between individual observers. A field (user) parallax
correction adjustment for the telescope and the mount is
NOTE. Before operation the crew should be also incorporated. Two separate reticle patterns, one for
familiarized with the location and operation of all controls the conventional round and one for the guided missile,
and instruments (figs. 2-23 through 2-29). may be presented separately in the field of view by
means of optical projection. Selection of reticles is made
b. M119 or M127 Telescope. The telescope, with by actuating a switch, while illumination intensity of either
associated M149 mount and checksight, is a primary fire the conventional ammunition or the missile pattern is
control instrument employed by the gunner. The M127 is controlled by a rheostat on the gunner’s reticle dimmer
similar to the M119 in design and operation, with the box. Accurate boresight retention is ensured when the
additional feature of dual (8 or 12) power magnification. patterns are interchanged because no physical
A selector lever, mounted on right side of telescope, movement of parts is required. Associated equipment
provides 12X magnification when positioned toward necessary for proper installation and operation of the
operator. (Advantage: Provides gunner with choice of M119 or M127 Telescope consists of:
magnification when viewing targets for either
conventional or missile round. ) The M127 will replace (1) M149 Telescope Mount. The mount supports
the M119 in all M551 vehicles. the missile tracker which is part of the missile
subsystem. A checksight mounted on the left
The telescope is a hermetically sealed direct fire control side of the assembly is used for optical
instrument for conventional ammunition, and, with a alignment of the missile tracker and the
associated tracker, is also part of the missile subsystem. telescope.
The telescope, attached to the mount, is mounted
coaxially with the 152MM gun -launcher and embodies
2-35
C9, TM 9-2350-230-12
(2) Checksight. The checksight is an opto- and body) are not interchangeable between XM44 and
mechanical device for checking the alignment of XM44E Series. Except where specifically indicated
the tracker and telescope with respect to each otherwise, operation and maintenance procedures are
other, and to check the proper functioning of the identical for all models.
missile tracker. The checksight is mounted in a Periscope (fig. 2-26) is a major component of the fire
cavity on the left side of the M149 Mount. control system and serves as the primary "night" fire-
(3) Tracker. The tracker is the eye of the missile control instrument. The Periscope consists of two major
subsystem and monitors the missile in flight with assemblies, the head assembly and the body assembly.
the line of sight. The head assembly provides a large entrance aperture
and the means for elevating and depressing the field of
c. XM44 Series Gunner’s Periscope. view. The body assembly houses a large aperture
optical system to pass as much of the available light as
NOTE. The XM44 Periscope, together with the later possible, an image intensifier tube, an optical system to
design XMi44E1 and XM44E2, comprise the "XM44 view the tube screen, a reticle projector system to
Series". In this manual, models are differentiated as superimpose a ballistic reticle pattern on the target
follows: "XM44 Series" all “’XM44E Series" all except image, and the unity power optical system for direct "day"
XM44 "XM44" XM44 only. viewing.
These periscopes are all interchangeable as complete d. Individual Weapons Night Vision Sight. The
units, but major assemblies (i. e. head Individual Weapons Night Vision Sight (fig. 2-29) is a
battery-powered, electro-optical device for visual
observation and aimed fire at night under ambient sky
light for the cal. .50 machine gun, M2, HB and also can
be used as a hand-held surveillance device. The sight
offers maximum freedom from the possibility of enemy
detection.
TABLE 2-9. OPERATION OF M119 OR M127 TELESCOPE, XM44 SERIES PERISCOPE,

AND ARMAMENT BORESIGHT PROCEDURE
ALIGNING GUN-LAUNCHER AND 7.62MM MACHINE GUN
1 Position vehicle on level ground.

2 Secure muzzle boresight (black thread) in reference marks on gun 2-23/A
muzzle with strap or tape.
3 Open breech and insert breech boresight assembly. 2-23/B
4 Position right telescope of binocular M17Al over hole of breech 2-23/B
boresight assembly and select a distant aiming point at approxi-
mately 1200 meters with sharply defined vertical and horizontal
lines. Align muzzle boresight cross hairs on aiming point by
traversing and elevating weapon.
5 Align machine gun. 2-24
OPERATING GUNNER’S M119 OR M127 TELESCOPE

7 Turn FIRE CONTROL selector to CONV position. The correspond- 2-19
ing lamp above the selector will illuminate.
8 Turn RETICLE LIGHT rheostat knob on reticle dimmer box clock- 2-25/1 &
wise for increased intensity of reticle lamp. 2-25.1/6
9 Adjust headrest to fit gunner. 2-25
10 Pull and turn diopter knob until proper focus is obtained. 2-52/2
2-36
C 10, TM 9-2350-230-12
AND ARMAMENT BORESIGHT PROCEDURE - Continued
NOTE. Operation, parallax adjustments, and boresighting

can be performed with the M127 Telescope in either of the two
power (8X or 12X) positions.
PARALLAX ADJUSTMENTS -
TELESCOPE M119 OR M127 AND MOUNT M149
11 Parallax adjustment between the telescope M119 or M127 and mount 2-25/15
M149 is a screwdriver adjustment and is accomplished as deemed
necessary by the operator. The control is located on the upper
side of the telescope above the filter selector lever. While
observing a target at 1200 meters through the eyepiece, and the
vertical reticle line adjacent to the target reference, move the
head up and down and sideways. If the reticle marking of the target
seems to move, adjust screw to obtain minimum parallax between
the target and the reticle as the eye is moved back and forth across
the eyepiece.
BORESIGHTING M119 OR M127 TELESCOPE CONV. RETICLE PATTERN,
12 Pull and turn elevation and azimuth knobs until conventional reticle 2-23/E and
is aligned with aiming point. 2-25/7, 9
13 Slip scales on elevation and azimuth boresight knobs to position "1". 2-25/7, 9
BORESIGHTING M119 OR M127 TELESCOPE MISSILE RETICLE PATTERS
14 Turn FIRE CONTROL selector to MISSILE position. The missile 2-19and

reticle will appear in the telescope. 2-23/D
15 View through telescope but do not adjust. 2-25
NOTE. Distant aiming point (any portion) must align with upper
square area of missile reticle pattern in telescope. If not, proceed
with tracker alignment procedure (table 2-12, step 12) and recheck.
If reticle is still not aligned, notify organizational maintenance
personnel.
OPERATING PROCEDURES FOR XM44 SERIES PERISCOPE
NOTE To be used when ambient light conditions do not permit

use of telescope.
16 Close periscope unity power window cover. 2-26/12
NOTE. If the periscope is not equipped with a unity power

window cover plate, place tape or other material over the unity
power window to avoid backlighting the system.
2-37
C 10, TM 9-2350-230-12
OPERATING PROCEDURES FOR XM44 SERIES PERISCOPE

Continued
17 Turn off or reduce intensity of all internal lights (dome lights, panel
lights, etc. ). This will improve gunner’s viewing ability.
18 Place filter of periscope in the dark position. 2-26/21
19 Deleted.
20 Open ballistic cover. 2-26/8, 9
21 Place periscope ON/OFF switch to the ON position. 2-26/ 6
NOTE. If a green flash of light is seen briefly and the image tube
goes out, the exterior light level is too high for operating the peris-
cope.
22 Adjust headrest. 2-26/11
23 Select filter which provides the best lighting condition of the image 2-26/21
tube without cutting it off.
24 Turn focusing knob-to infinity position (max. ccw). 2-26/23
25 Adjust reticle light intensity control clockwise for proper illumina- 2-26/5
tion of reticle pattern. Proper illumination is obtained
when reticle is barely visible.
25.1 Slip boresight knobs to position "1".
26 While observing reticle through eyepiece of periscope, pull out 2-26/22
diopter knob and adjust setting until reticle appears with maximum
sharpness.
27 Set periscope on a distant visible target. Rotate focusing knob until 2-26/23
target is sharply defined. Re-adjust diopter setting if required.
NOTE 1. Focus must be adjusted for each change of target range.
NOTE 2. In the event vehicle power is lost, switch periscope 2-26/6
ON/OFF switch to emergency power position. In the emergency
position, the reticle should be used as little as possible to conserve
battery power. 2-26/17
NOTE 3. Turn reticle pattern off for ultimate performance in
scanning operation.
When periscope is not in use:
28 Turn periscope ON/OFF switch to OFF position. 2-26/6
29 Turn filter to DARK (XM44) or OFF (XM44E Series) 2-26/21
30 Close ballistic cover. 2-26/8, 9
BORESIGHTING GUNNER’S XM44 SERIES PERISCOPE
NOTE. XM44 Series periscopes are boresighted and zeroed at a

distance of 1200 meters.
CAUTION: Use periscope boresight aid (10516830) when

boresighting in daylight. Use dark position filter to prevent exces-
sive light from damaging internal components when boresighting or
at all times when periscope is not in use.
31 Pull and turn elevation and azimuth boresight knobs until reticle is 2-26/24, 26,
aligned with aiming point. and 2-23/F
32 Turn slip scales on elevation and azimuth boresight knobs to posi- 2-26/24, 26
tion "1".
2-38
C 10, TM 9-2350-230-12
BORESIGHTING GUNNER’S XM44 SERIES PERISCOPE - Continued
NOTE. If periscope can not be boresighted, refer to

organizational maintenance personnel.
AFTER OPERATING AND/OR BORESIGHTING
33 Remove breech boresignt assembly and muzzle boresight. 2-23/A, B
34 Turn FIRE CONTROL selector to OFF position. Lamps will go out. 2-19
35 Turn RETICLE LIGHT INTENSITY knob fully counterclockwise and 2-26/3, 21

position filter selector to DARK (XM44) or OFF (XM44E Series).
Leave selector in this position when periscope is not in use.
36 Turn periscope ON/OFF switch to OFF position. 2-26/6
CAUTION: Insure that boresight aid (10516830) is removed.

Failure to comply could cause damage to the wiper assembly.
CAUTION: Make certain that periscope ON/OFF switch is in

OFF position to prevent draining periscope battery.
37 Close periscope ballistic cover. 2-26/8, 9
38 Turn MASTER SWITCH off.
2-38.1
C9, TM 9-2350-230-12
TABLE 2-9.1. ZEROING M119 OR M127 TELESCOPE AND XM44 SERIES PERISCOPE
1 Perform procedures described in table 2-9, steps 1 through 32.
2 Apply emergency zero to telescope by turning boresight knobs (CONV) 2-25/7, 9

to elevation "5" and azimuth "2".
3 Select a well-defined point in the target area at a range of 1200 meters 2-23
(use a 12 x 12 ft target when possible).
4 Select CONV on the gun and turret control selector. 2-19
5 Using the manual controls, lay the zeroing cross of the-telescope 2-19, 2-23
(1200 meters range line) on the aiming point.
6 Fire a warmer round, followed by three rounds of the same lot number, 2-19
to form a shot group. Re-lay the gun on the same aiming point after
each round, using the manual controls.
7 When firing has been completed, re-lay the sight on the aiming point.
8 Without disturbing the lay of the gun, using the telescope boresight 2-25/7, 9
knobs (CONV) move the zeroing cross (1200 meter range line) to the
center of the shot group.
9 Re-lay on the aiming point, using the manual controls and fire a check 2-19
round. The projectile should strike within 24 inches of the aiming point.
If it does not, fire a second check round. If either round strikes within
the specified distance from the aiming point, the gun is zeroed. If not,
the zeroing procedure is continued until a check round strikes within
the prescribed distance.
10 With the gun-launcher zeroed, and using the manual controls, lay the 2-19
telescope zeroing cross back on aiming point.
11 Using the boresight knobs on the periscope, move the reticle 2-26/24, 26
pattern 1200 meter range line to same aiming point as the telescope. 2-23/F
12 A check round may be fired, using periscope to verify that

the periscope is zeroed.
13 Record zero setting of the telescope and periscope, and place in

convenient part of the turret.
14 Slip scales on telescope (CONV) and gunner’s periscope boresight

knobs to position "4".
2-38.2
C8, TM 9-2350-230-12
Figure 2-23. Weapons system boresighted on distant aiming point
2-39
C6, TM 9-2350-230-12
ALIGNMENT PROCEDURE
1. REMOVE SPENT BRASS CHUTE EXTENSION
(FIG. 3-7).
2. REMOVE 2 SCREWS AND WASHERS, REMOVE
BRACKET WITH SPENT BRASS CHUTE AND BAG.
3. PULL REARWARD ON DISCONNECTOR RING,
ROTATE RECEIVER CLOCKWISE AND REMOVE.
4. LOOSEN 2 MOUNTING SCREWS SLIGHTLY.
5. LOOK THROUGH BARREL AND LOOSEN UPPER
OR LOWER ADJUSTING SCREW TO ALIGN
BARREL IN ELEVATION WITH DISTANT AIMING
POINT. TIGHTEN OPPOSITE ADJUSTING
SCREW AND 2 MOUNTING SCREWS (ITEM 4).
6. LOOSEN 2 MOUNTING SCREWS SLIGHTLY.
7. LOOK THROUGH BARREL AND LOOSEN LEFT OR
RIGHT ADJUSTING SCREW TO ALIGN BARREL IN
AZIMUTH WITH DISTANT AIMING POINT.
TIGHTEN OPPOSITE ADJUSTING SCREW AND 2
MOUNTING SCREWS (ITEM 6).
8. PULL REARWARD ON DISCONNECTOR RING
(ITEM 3), ROTATE RECEIVER
COUNTERCLOCKWISE AND INSTALL RECEIVER.
Figure 2-24. Aligning 7.62 mm machine gun
2-40
C9, TM 9-2350-230-12
M149 MOUNT (TELESCOPE

REMOVED FOR CLARITY)
1. RETICLE LIGHT RHEOSTAT KNOB
2. DIOPTER KNOB (FOCUS ADJUSTMENT)
3. FILTER LEVER (CLEAR, NEUTRAL,
DENSE)
4. AZIMUTH KNOB (MISSILE RETICLE)
5. CONVENTIONAL AMMUNITION
RETICLE LAMP COVER LATCH
6. ELEVATION KNOB (MISSILE RETICLE)
7. AZIMUTH KNOB (CONVENTIONAL
RETIC LE)
8. MISSILE RETICLE LAMP HOUSING
9. ELEVATION KNOB (CONVENTIONAL
RETICLE)
10. ERROR LEVER
11. ALIGN LEVER
12. CHECKSIGHT LAMP
13. AZ SCREW
14. EL SCREW
15. PARALLAX ADJUSTMENT (Ml19 OR
M119 TELESCOPE AND RETICLE DIMMER BOX M127)
16. MAGNIFICATION POWER LEVER (MI27
ONLY)
M127 TELESCOPE
M119 OR M127 TELESCOPE

HEADREST
WE 66592 U
Figure 2-25. Gunner’s M119 or M127 telescope controls
2-41
C9, TM 9-2350-230-12
Figure 2-25.1. M119 or M127 telescope emergency reticle light power box assembly
and reticle dimmer box (effective vehicle SN 140)
2-42
C 10, TM 9-2350-230-12
Figure 2-25. 2. Telescope mount M165 and gun and turret control selector
on vehicles without missile capability.
2-42.1
C 10, TM 9-2350-230-12
Figure 2-26. XM44 series periscope controls and instruments.
2-42.2
C 10, TM 9-2350-230-12
TABLE 2-10. OPERATION OF INDIRECT FIRE CONTROL INSTRUMENTS
1 Traverse turret and elevate or depress 152MM gun-launcher until 2-23/E, F

gunner’s periscope (XM44 Series) or telescope (M1i9 or M127)
conventional reticle is exactly on reference point.
2 Depress slightly and rotate resetter knob of azimuth indicator until 2-27
micrometer pointer coincides with azimuth pointer. Depress resetter
knob further and rotate both pointers to zero.
3 To determine the deflection to a given target, traverse the turret until 2-27
the aiming cross of the gunner’s periscope reticle is properly aligned
on the target. Read directly from the azimuth indicator the sum of the
micrometer and azimuth pointers.
4 To make small deflection corrections, rotate gunner’s aid dial until 2-27
zero graduation is opposite micrometer pointer. Use the micrometer
pointer in conjunction with the gunner’s aid (dial) to make a right or
left shift of 50 mils or less in deflection.
5 Rotate micrometer elevation knob of M13A1C elevation quadrant until 2-28/B
sum of elevation scale and micrometer scale readings equal required
elevation angle. Elevate or depress gun-launcher until bubble in level
vial is centered. Gun is now layed in elevation.
NOTE. 1. If possible, the vehicle should be positioned on level 2-28

ground.
2. Either M1SAIC elevation quadrant or M1A1 gunner’s
quadrant may be used to lay gun in elevation. If M1A1 quadrant is
used, note any deviation between centerline of weapon and quadrant
seat (stamped above quadrant seat, fig. 2-28). If deviation exists,
compensate by presetting quadrant.
6 Disengage index plunger from notches in frame of M1A1 gunner’s 2-28/A

quadrant by pressing plunger into index arm. Raise index arm and
set index plate to nearest graduation on elevation scale below required
elevation angle. Rotate micrometer knob to fine reading.
NOTE. If required elevation angle is 327 mils, set index plate at 32C
mils, and turn micrometer knob until scale indicates 7 mils: quadrant
is now set at 327 mils.
7 Place shoes of MlA1 quadrant on quadrant seat of 152MM gun-launcher 2-28/A

mount with inscribed arrow on quadrant pointing toward muzzle end
of gun-launcher. Elevate or depress gun-launcher until bubble in
level vial is centered. Gun-launcher is now layed in elevation.
NOTE. Before using, wipe shoes of gunner’s M1A1 quadrant and

quadrant seat to insure accuracy.
2-43
C10, TM 9-2350-230-12
WE 66695
Figure 2-27. Checking and adjusting azimuth indicator for accuracy and slippage
2-44
C6, TM 9-2350-230-12
A. GUNNER’S M1A1 QUADRANT B. M13A1C ELEVATION QUADRANT.

DETERMINING M1A1 QUADRANT CORRECTION ZEROING M13AIC QUADRANT
1. MOVE VEHICLE TO APPROXIMATELY LEVEL GROUND. 6. COMBINE M1A1 CORRECTION WITH QUADRANT SEAT
2. SET M1A1 QUADRANT TO ZERO ELEVATION. CORRECTION (STAMPED ON QUADRANT SEAT). SET TOTAL
3. PLACE M1A1 QUADRANT ON QUADRANT SEAT AND ELEVATE CORRECTION ON M1A1 QUADRANT AND ELEVATE OR
OR DEPRESS GUN LAUNCHER TO CENTER BUBBLE IN DEPRESS GUN LAUNCHER TO CENTER BUBBLE. GUN
QUADRANT LEVEL VIAL. LAUNCHER IS NOW LEVEL.
4. TURN QUADRANT END FOR END, AND CHECK TO SEE IF 7. ADJUST M13AIC QUADRANT WITH MICROMETER KNOB UNTIL
BUBBLE IS CENTERED. BUBBLE IS CENTERED IN LEVEL VIAL.
A. IF BUBBLE IS CENTERED, QUADRANT CORRECTION 8. IF MICROMETER SCALE DOES NOT READ ZERO, LOOSEN 3
IS ZERO. SCREWS, PULL OUT ON KNOB AND ROTATE UNTIL ZERO
B. IF BUBBLE CAN BE CENTERED WITH MICROMETER READING IS OBTAINED. TIGHTEN SCREWS.
KNOB, DIVIDE MICROMETER READING BY 2. 9. IF ELEVATION SCALE DOES NOT READ ZERO LOOSEN TWO
THIS IS A PLUS CORRECTION. SCREWS SECURING SCALE TO HOUSING AND ALIGN ZERO
C. IF BUBBLE CANNOT BE CENTERED WITH ON SCALE WITH INDEX. TIGHTEN SCREWS.
MICROMETER KNOB, DROP INDEX PLUNGER 1 CLICK (10
MILS), THEN CENTER BUBBLE WITH MICROMETER KNOB.
SUBTRACT MICROMETER READING FROM 10AND DIVIDE
BY 2. THIS IS A MINUS CORRECTION.
5. SET CORRECTION IN QUADRANT, DEPRESS OR ELEVATE
GUN LAUNCHER TO CENTER BUBBLE, AND AGAIN TURN
QUADRANT END FOR END. BUBBLE WILL BE CENTERED IF
CORRECTION HAS BEEN ACCURATELY DETERMINED. IF NOT,
REPEAT STEPS 2 THROUGH 5.
WE 12066
Figure 2-28. Adjusting M13A1C elevation quadrant
2-45
C2, TM 9-2350-230-12
TABLE 2-11. INSTALLATION, OPERATION, AND BORESIGHT PROCEDURE FOR CAL .SO
MACHINE GUN NIGHT VISION SIGHT (FIG. 2-29)
INSTALLATION
1 Perform before operation preventive-maintenance checks and services

(table 4-1, step 60).
2 Unzip stowage bag and remove the night vision sight from retaining straps 13
3 Loosen four wing nuts, thumbscrews, and slide adapter bracket from 11,12, 14
stowage bracket.
4 Slide adapter bracket into sight bracket and tighten lock levers 10,16
CAUTION: Never point the objective lens at the sun or other light source
of comparable brightness.
5 Open machine gun cover and slide sight w/adapter bracket onto receiver. 15,16
Close cover.
6 Tighten four thumb screws and secure with wing nuts. 11 and 12
7 Remove lens cap. 1
8 Remove battery cap. Install battery with positive end forward 7
OPERATION
WARNING: Keep eyeshield in contact with face to prevent emission of

visible glow from eyepiece.
9 Turn reticle lamp illumination switch on 6

10 Focus eyepiece by rotating focus ring until reticle pattern appears sharp 8
NOTE. Remember diopter scale setting for future quick focusing.
11 Unlock objective lens focus knob locking device 17

12 Focus objective lens with focus knob 2
13 Lock objective lens focus knob locking device, taking care not to disturb 17
focus knob setting.
14 Rotate azimuth and elevation knobs to adjust position of reticle pattern 3 and 4
NOTE. Each click of azimuth and elevation adjustment knobs represents

a 1/2 mil movement of the reticle. Total movement of either
knob is plus or minus 26 mils.
BORESIGHTING
15 Align cal..50 machine gun sights on a target at a distance of 150 meters.

16 Align reticle aiming reference dot on same target 18
AFTER OPERATION
17 Turn reticle lamp illumination switch off 6

18 Remove battery and install lens and battery caps 1,7
19 Remove sight and adapter bracket from gun and stow 13 and 14
2-46
C6, TM 9-2350-230-12
Figure 2-29. Night vision sight for cal. .50 machine gun
2-47
C3, TM 9-2350-230-12
Section 2-6. OPERATION AND DESCRIPTION OF MISSILE GUIDANCE

AND CONTROL SYSTEM
2-7. GUIDANCE AND CONTROL SYSTEM f. Test Checkout Panel. This panel (fig. 2-31) is used
DESCRIPTION to initiate the following operational tests of the guidance
and control system:
The guidance and control system for the missile
consists of the following components: tracker, rate (1) Lamp and meter test
sensor, signal data converter, modulator, power supply, (2) Transmitter test
test checkout panel, and the transmitter. These (3) Tracker alignment test
components control the missile during its flight from the (4) System self test
gun-launcher to the target (see fig. 2-30).
2-7.1. OPERATING INSTRUCTIONS
a. Optical Tracker. This unit is the "eye" of the
system and is mounted just above, and aligned with, the The guidance and control system checkout procedures
gunner’s telescope. During a missile firing, it tracks the are outlined in table 2-12 below. A complete checkout of
in-flight missile, determines how far it has moved from the system is accomplished in four basic tests. These
the line of sight, then sends the information to the signal tests should be performed in the sequence given. Each
data converter (SDC). test is described below.
b. Rate Sensor. The rate sensor produces signals a. Lamp and Meter Test. This test checks that all
corresponding to the rate of turret traverse, gun elevation lamps on the test checkout panel will light and that the
or depression. These signals are sent to the signal data test checkout panel null meter is operating properly.
converter to assist in making it possible for the missile to
follow a moving line of sight as the gunner is tracking a b. Transmitter Test. This test checks that both
moving target. transmitter lamps will light and that the transmitter is
operating properly.
c. Signal Data Converter. The SDC is the command
center of the guidance and control system. The SDC c. Tracker Alignment Test. This test aligns the
combines signal output from the tracker with turret missile reticle in the gunner’s telescope so that the
traverse and gunlauncher elevation rate information from gunner is viewing the same line of sight as the tracker.
the rate sensor to compute corrections necessary to
d. System Self Test. This test automatically analyzes
keep the missile on the line of sight. The correction
the operating condition of the guidance and control
signals are then sent to the modulator as missile
system and displays the result as a red no/go lamp for
command signals.
the unit that is defective or as a green GO lamp if all
d. Modulator. The modulator takes the signals from units are functioning normally.
the signal data converter and converts them to high
current output to operate the transmitter. NOTE. Before operation, the crew should be
familiarized with the location and operation of all
e. Optical Transmitter. The transmitter converts the
controls and instruments (figs. 2-19, 2-23, 2-25,
high current electrical signals into infrared signals. A
2-26, 2-30 and 2-31).
narrow infrared beam, containing guidance command
signals is then sent to the missile.
2-48
C8, TM 9-2350-230-12
TABLE 2-12. MISSILE GUIDANCE AND CONTROL SYSTEM CHECKOUT PROCEDURES
PRELIMINARY INSTRUCTIONS
NOTE. Steps 2, 3, 4 and 6 are performed only when a missile

firing is to occur immediately after completion of check-out procedures.
1 Perform before-operation preventive-maintenance checks and

services (table 4-1, sequence no. 61 and 62).
1A Boresight conventional and missile reticle patterns (table 2-9).
2 Turn and push control handle to open transmitter door. Turn 2-26/14
handle clockwise to lock door open.
3 Turn TURRET CONTROL POWER switch off 2-19
4 Set SAFE/READY switch on loader’s control box to SAFE position 3-1A
ENERGIZING THE GUIDANCE AND CONTROL SYSTEM
5 Start vehicle engine and set- idle speed to at least 1750 rpm (table 2-3, 2-9
steps 1 through 19).
6 Turn TURRET CONTROL POWER switch on if operating turret in
power mode (table 2-7). Lamp above switch will glow.
7 Turn FIRE CONTROL selector to MISSILE position. Lamp above
switch will glow, POWER SUPPLY lamp on test checkout panel will 2-31/5
blink during warm-up but will go out when system is warmed up, and
missile reticle appears in telescope 2-23D
LAMP AND METER TEST
8 Hold LAMP AND METER TEST switch on test checkout panel in the 2-31/12
UP position. All the lamps on test checkout panel should glow and 2-31
null meter needle should deflect to METER TEST band 2-31/1
9 Rotate DIMMER control on test checkout panel. Brightness of all 2-31/10
lamps except the red lamps should vary.
10 Release LAMP AND METER TEST switch 2-31/12
TRANSMITTER TEST
WARNING: Do not look directly into transmitter regardless of

distance. Transmitter emits invisible infrared rays which can cause
serious eye damage.
CAUTION: Do not leave XMTR TEST switch in up position for

more than 1 minute.
11 Set XMTR TEST switch on test checkout panel to up position. XMTR 2-31/13
TEST and XMTR lamps should glow. If transmitter is defective
XMTR TEST switch will return to down position in approximately
10 seconds. If this occurs, notify organizational maintenance.
2-48.1
C8, TM 9-2350-230-12
TABLE 2-12. MISSILE GUIDANCE AND CONTROL SYSTEM CHECKOUT PROCEDURES—Continued
TRANSMITTER TEST - Continued
12 Hold RESET switch on test checkout panel up and then release 2-31/11
XMTR TEST switch returns to down position 2-31/13
TRACKER ALIGNMENT TEST
13 Move ALIGN lever on the telescope mount to the fully right position 2-25/11
13A Check to insure that ERROR lever is in its extreme left position 2-25/10
13B Check to insure telescope filter lever is in CLEAR position 2-25/3
14 Set TRACKER ALIGN switch on test checkout panel to up position 2-31/14
TRACKER ALIGN lamp should glow, and a spot of light should
appear in the telescope. If necessary, temporarily cover or shade
the telescope opening outside the turret to make the spot of light
more visible.
15 Set AZ/EL switch on test checkout panel to AZ (down) position. AZ 2-31/16
lamp should glow and null meter needle should indicate in center of 2-15/13
lower green band. If not, adjust AZ screw located beneath ALIGN
lever on telescope mount to bring needle into center of lower green
band.
16 Set AZ/EL switch to EL (up) position. EL lamp should glow, and 2-31/16
null meter needle should indicate in center of lower green band. If 2-25/14
not, adjust EL screw located beneath ALIGN lever on telescope
mount to bring needle into center of lower green band.
17 Repeat steps 15 and 16 to insure there is no interaction of adjustments .
18 Look into telescope and using missile azimuth and elevation knobs, 2-54/4, 6
center missile reticle circle over checksight spot of light.
19 Hold RESET switch on test checkout panel up and then release 2-31/11
TRACKER ALIGN switch returns to down position, and ALIGN lever 2-31/14
moves to the left and the spot of light disappears 2-25/11
NOTE. Whenever there is a rapid temperature change of 30°F

or more, repeat tracker alignment test.
SYSTEM SELF TEST
20 Move ALIGN and ERROR levers on the telescope mount to fully right 2-25/10, 11
position.
NOTE. If align lever resets left at any time during system self-
test immediately reposition lever to extreme right and continue with
self-test.
2-48.2
C8, TM 9-2350-230-12
TABLE 2-12. MISSILE GUIDANCE AND CONTROL SYSTEM CHECKOUT PROCEDURES-Continued
SYSTEM SELF TEST - Continued
21 Set SYSTEM TEST switch on test checkout panel to up position 2-31/15

SYSTEM TEST and AZ or EL lamps should glow. The GO lamp
should glow after 30 second delay. If a guidance and control unit
malfunctions, its corresponding lamp will glow and the GO lamp will 2-31/11
not glow. If a malfunction occurs hold the RESET switch up and then
release. De-energize the system (steps 28 through 33) and notify
organizational maintenance
22 Set the AZ/EL switch to the AZ (down) position. AZ lamp should 2-31/16
glow.
23 Traverse turret to left and right (table 2-7) Null meter needle moves 2-31/1
in the same direction as turret. When movement ceases, needle
returns to lower green null band. If not, notify organizational main-
tenance.
24 Set AZ/EL switch to the EL (up) position. The EL lamp glows 2-31/16
25 Move gun-launcher up and down. Null meter needle moves to the
right as gun-launcher is raised and to the left as gun-launcher is
lowered. When movement ceases, needle returns to lower green
null band. If not, notify organizational maintenance.
26 Hold RESET up and then release. SYSTEM TEST switch returns to 2-31/11
down position. ALIGN lever returns to the left.
27 Move ERROR lever on telescope mount to the left 2-25/10
SYSTEM SELF TEST VERIFICATION
27A Move ALIGN and ERROR levers on telescope mount to fully left 2-25/10, 11
position.
27B Set the SYSTEM TEST switch on the test checkout panel to up 2-31/16
position. TRACKER lamp should glow. If not, notify organizational
maintenance.
27C Hold RESET switch up and then release 2-31/11
27D Repeat step 27B with ALIGN lever positioned fully right and ERROR
lever fully left. SIG DATA CONV lamp should glow. If not notify
organizational maintenance.
27E Hold RESET switch up and then release.
WARNING: Before proceeding, insure that all weapons are

cleared of live rounds.
27F Set SAFE/READY switch on loader’s control box to READY position.

Move ALIGN lever fully right and ERROR lever fully left. Insure
that gunner’s READY lamp is glowing. Set the SYSTEM TEST switch
to the up position then pull the fire trigger.
2-49
C8, TM 9-2350-230-12
TALE 2-12. MISSILE GUIDANCE AND CONTROL SYSTEM CHECKOUT PROCEDURES-Continued
SYSTEM SELF TEST VERIFICATION (Continued)
Test checkout panel should reset; ALIGN lever should move fully
left; and the tracker motor should run for approximately 3 seconds.
If not, notify organizational maintenance.
DE-ENERGIZING THE MISSILE SUBSYSTEM
NOTE. Do not de-energize the subsystem if going directly into

a firing mission.
28 Check to insure that SAFE/READY switch is in SAFE position 3-1/A

29 Turn FIRE CONTROL selector to OFF position. MISSILE lamp 2-19
goes out.
30 Turn TURRET CONTROL POWER switch OFF. Lamp above switch 2-19
goes out.
31 Stop vehicle engine (table 2-3).
32 Close transmitter door, and turn handle clockwise to lock door 2-26/14
closed.
2-50
C 3, TM 9-2350-230-12
Figure 2-30. Missile subsystem units
2-51
C3, TM9-2350-230-12
1. NULL METER. INDICATES ALIGNMENT OF TRACKER DURING 9. GO LAMP (GREEN). INDICATES OPERATIONAL CONDITION
TRACKER ALIGNMENT TEST AND OPERATIONAL CONDITION OF GUIDANCE AND CONTROL SYSTEM DURING SELF TEST.
OF RATE SENSOR DURING SYSTEM SELF TEST 10. DIMMER CONTROL. ADJUSTS THE BRIGHTNESS OF ALL
2. XMTR LAMP (RED). INDICATES OPERATIONAL CONDITION LAMPS EXCEPT THE RED NO/GO LAMPS.
OF THE TRANSMITTER DURING SYSTEM SELF TEST. 11. RESET SWITCH. TURNS OFF ALL CONTROL SIGNALS. USED
3. CHECKOUT PANEL LAMP (RED). INDICATES OPERATIONAL DURING TRACKER ALIGNMENT TEST, SYSTEM SELF TEST,
CONDITION OF THE TEST CHECKOUT PANEL DURING AND TRANSMITTER TEST.
SYSTEM SELF TEST. 12. LAMP AND METER TEST SWITCH. INITIATES THE TEST OF
4. TRACKER LAMP (RED). INDICATES OPERATIONAL ALL LAMPS AND THE NULL METER ON THE TEST CHECKOUT
CONDITION OF THE TRACKER DURING SYSTEM SELF TEST. PANEL.
5. POWER SUPPLY LAMP (RED). INDICATES OPERATIONAL 13. XMTR TEST SWITCH AND LAMP (WHITE). SWITCH TURNS ON
CONDITION OF THE POWER SUPPLY DURING SYSTEM BOTH TRANSMITTER LAMPS DURING TRANSMITTER TEST.
OPERATION. 14. TRACKER ALIGN SWITCH AND LAMP (WHITE). INITIATES THE
6. SIG DATA CONV LAMP (RED). INDICATES OPERATIONAL ALIGNMENT TEST OF THE TRACKER.
CONDITION OF THE SIGNAL DATA CONVERTER DURING 15. SYSTEM TEST SWITCH AND LAMP (WHITE). INITIATES THE
SYSTEM SELF TEST. SYSTEM SELF TEST.
7. PRIME VOLTAGE LAMP (AMBER). IF LAMP GLOWS AFTER 16. AZ/EL SWITCH AND LAMPS (WHITE). SELECTS AZIMUTH AND
SYSTEM WARM-UP THE VEHICLE POWER TO THE SYSTEM ELEVATION SIGNALS FROM THE RATE SENSOR FOR TEST.
IS LOW. IT IS ALSO USED DURING THE ALIGNMENT TEST OF THE
8. MOD LAMP (RED). INDICATES OPERATIONAL CONDITION OF TRACKER TO INDICATE AZIMUTH AND ELEVATION
THE MODULATOR DURING SYSTEM SELF TEST. ALIGNMENT.
WE 10908B
Figure 2-31. (Superseded) Missile subsystem test checkout panel
2-52
C9, TM 9-2350-230-12
Section 2-7. OPERATION OF SPECIAL PURPOSE KITS
2-8. Operation Instructions The winterization kit coolant heater is to be used

when engine is shutdown in ambient temperatures at -
The following tables and illustrations provide special 250F. to -650F., to raise engine oil, engine coolant and
purpose kits operating instructions. battery electrolyte temperatures.
2-9. Operation of Winterization Kit Coolant Heater 2-10. -Deleted.
(table 2-13) 2-11. Searchlight Kit (tables 2-14.15.16)
TABLE 2-13. OPERATION OF ENGINE COOLANT HEATER (-250F. TO -650F.)
BEFORE OPERATION
1 Fold back and secure flap on forward left corner of grille cover to 2-32
uncover heater exhaust pipe.
WARNING: When operating winterization kit coolant heater,

turret must be positioned so that neither grenade projector is over
the heater exhaust outlet.
STARTING AND OPERATING HEATER
NOTE. The duration of time that the winterization kit can be operated
is dependent upon the amount of battery capacity available. Care should be
taken not to operate other vehicle electrical equipment while the kit is in
operation. Three to 5 hours of kit operation is required prior to attempt-
ing an engine start on a cold soaked vehicle.
2 Vehicle master switch should be in the "OFF" position 2-10
NOTE. Heater may be operated with vehicle master switch in "ON"

or "OFF" position. It is recommended that the "OFF" position be used
to minimize battery drain.
3 Be sure fuel supply valve on center fuel tank is open.

4 Depress coolant heater control box indicator light to test. Indicator 2-32/2
light will illuminate.
NOTE. If indicator light does not illuminate, replace lamp and/or

determine cause for lack of electrical continuity.
5 Place heat selector switch in "LO" position 2-32/1

6 Hold heat control switch in "START" position until indicator light
illuminates (1 to 3 minutes).
CAUTION: If indicator light does not illuminate within 3 minutes,

turn heat control switch to "OFF" position and wait 5 minutes. Repeat
step 5 to make a second attempt to start heater. If the light does not
illuminate after a third attempt, turn heat control switch to "OFF"
position and refer to Organizational Maintenance Personnel.
7 Snap heat control switch to "RUN" position 2-32/1

8 Place heat selector switch in "HI" position 10 minutes after the indicator 2-32/1, 2
light on the control box has illuminated.
2-53
C3, TM 9-2350-230-12
TABLE 2-13. OPERATION OF COOLANT HEATER (-25°F. TO -650F.) - CONTINUED
STARTING AND OPERATING HEATER - CONTINUED
NOTE: The heat selector switch should remain in the "HI" heat
position during prolonged use of the winterization kit. The coolant
thermostat will automatically switch the heater from high to low heat
thereby maintaining proper system temperatures.
BEFORE STARTING ENGINE
9 Unfasten 2 or 4 straps on engine intake grille cover and roll cover into 2-32/5, 7
smallest possible tube form and secure straps onto unused spacers at
forward end of exhaust grille.
10 Unfasten 3 or 5 straps on exhaust grilles cover and roll cover into 2-32/6, 8
smallest possible tube form, securing straps onto spacers at rearward
end of intake grille.
11 During prolonged engine operation or during main weapon firing, remove 2-32/4
grille cover.
12 Place heat control switch to center "OFF" position. Indicator light will 2-32/2, 3
remain illuminated and blower will continue to run for 2 or 3 minutes
until the combustion chamber has been purged.
13 Start vehicle engine.
NOTE. Do not operate winterization heater when engine is running.
AFTER OPERATION
14 Shut-down vehicle engine.

15 Secure grille cover in the closed position 2-32/4
2-54
C9, TM 9, 2350-230-12
Figure 2-32. Winterization kit
Figure 2-33. Deleted
(2-56 Blank) 2-55

C4, TM 9-2350-230-12
LEGEND
1. SEARCHLIGHT W/SUPPORT
2. MOUNTING BRACKET
3. LOCKING PIN (3)
4. HOUSING CAP
5. SEARCHLIGHT-TO-ROOF WIRING HARNESS
6. SCREW
7. CLAMP
8. MAIN CONTROL BOX
9. ROOF-TO-MAIN CONTROL BOX WIRING HARNESS
10. SCREW (4)
11. WASHER (4)
12. REMOTE CONTROL BOX
13. SCREW (4)
14. WASHER (4)
15. MAIN CONTROL BOX-TO-REMOTE CONTROL BOX WIRING HARNESS
16. MAIN CONTROL BOX-TO-ELECTRICAL CONTACT RING WIRING HARNESS
REFER TO TABLE 2-14 FOR STEP BY STEP INSTALLATION PROCEDURE.
WE 11963
Figure 2-34. (Superseded) Infrared searchlight kit installation.
2-57
C6, TM 9-2350-230-12
TABLE 2-14. INFRARED SEARCHLIGHT KIT INSTALLATION (FIG. 2-34)
Mfr ’s
F. S. N Part No Item
Infrared Searchlight Kit 5855-058-1293 AN/VSS-3
Consisting of:
1 - Main Control Box w/attaching Hardware ......... 5855-135-0155 C-7905/VSS-3 8, 10, 11
1 - Remote Control Box w/attaching Hardware .... 5855-135-0154 C-7906/VSS-3 12, 13,14
1 - Searchlight w/support...................................... 5855-135-0156 MX8272/VSS-3 1
1 - Cable Assembly (Searchlight-to-Roof) ............ Not Available CX-11893/VSS-3 5
STEP INSTALLATION PROCEDURE

WARNING: Make certain that VEHICLE MASTER switch is turned to the OFF
position.
1 Position searchlight with support (1) onto mounting bracket (2) and secure with 3 cam
operated locking pins (3) (See note, figure 2-35).
2 Remove housing cap (4) and connect searchlight-to-roof harness at each end (5).
Stow cap on threads provided on top of housing.
3 Remove and discard existing screw (6) securing clamp and roof-to-main control box
wiring harness (7).
4 Install main control box (8), clamp (7), and roof-to-main control box wiring harness (9)
and secure with 4 screws and washers (10 and 11). Connect wiring harness at main
control box.
5 Position remote control box (12) and secure with 4 screws and washers.
6 Connect main control box-to-remote control box wiring harness (15) at each end.
7 Connect main control box-to-electrical contact ring wiring harness (16) at control box.
SEARCHLIGHT LAMP REPLACEMENT
1 Remove searchlight front cover and remove spare lamp from container.
2 Place container over burned out lamp, engaging container ferrule with base of lamp.
Unscrew lamp counterclockwise and remove.
3 Place container over replacement lamp and install lamp in searchlight.
4 Remove container and install searchlight front cover.
Figure 2-35. Searchlight with support and mounting bracket.
2-58
C4, TM 9-2350-230-12
Figure 2-36. (Added’ Main and remote searchlight control boxes.
TABLE 2-15. INFRARED SEARCHLIGHT OPERATION
STEP PROCEDURE
WARNING: DO NOT look into searchlight beams. Serious eye damage can result.
BEFORE OPERATION
1 Clean searchlight exterior and make certain all connections are securely tightened.
2 Bracket jack screw and jam nut (7, 8, fig. 2-35) must be in firm contact with
gun shield.
3 Make certain the VISIBLE/INFRARED/OFF switch (9, fig. 2-36) is in OFF position.
4 Remove searchlight front canvas cover and stow.
NOTE. If window is dirty, clean with a dry or water dampened cloth.
WARNING: DO NOT clean when light is in operation.
2-59
C4, TM 9-2350-230-12
TABLE 2-15. INFRARED SEARCHLIGHT OPERATION - CONTINUED
STEP PROCEDURE
OPERATION
5 Start vehicle engine and run at fast idle (table 2-3 or 2-4. 1).
CAUTION: DO NOT operate searchlight without engine running.
6 Position LOCAL/REMOTE switch (10, fig. 2-36) on main control box as desired.
NOTE. The LOCAL/REMOTE switch on the main control box controls searchlight
useage and is operated at the main control box when in LOCAL position
and at the remote control box when in REMOTE position.
7 Pull outward on VISIBLE/INFRARED/OFF 3 position toggle switch (9, fig. 2-36) and
place in desired position. Green LAMP ON light (8, fig. 2-36) will illuminate and
searchlight lamp will ignite.
NOTE. 1. If the first ignition attempt does not illuminate the lamp, the ignition
process is automatically repeated.
NOTE. 2. If searchlight does not ignite after 15 to 20 seconds perform searchlight

system self test with circuit test switch knob (4, fig. 2-36) on main control
box. If system is found operable, lamp (300 hours minimum operation)
may be defective. Refer to table 2-14 for lamp replacement.
8 Place BEAM switch (7, fig. 2-36) in SPREAD light or COMPACT light position.
NOTE. The operator can control the SPREAD light beam by very quickly pressing
switch on and off and obtain a light spread from 1 to 7 degrees,
CAUTION: If during operation, the OVER TEMP red light (5, fig. 4) comes on, due
to blower motor failure, turn searchlight off and notify Organizational
Maintenance Personnel.
AFTER OPERATION
9 Turn VISIBLE/INFRARED/OFF switch (9, fig. 2-36) to OFF position. Green

LAMP ON light (8, fig. 2-36) and searchlight go out.
WARNING: DO NOT disconnect electrical harness or open equipment for any reason
until after system has been shut down, and blower motor in searchlight
has stopped.
CAUTION: DO NOT turn VEHICLE MASTER switch off until the searchlight blower
motor shuts off. The blower motor is automatically controlled by a
temperature sensing switch in the searchlight.
10 Install searchlight canvas front cover.
11 If searchlight and support are removed, stow elevation adjustment screw in clip.
2-60
C4, TM 9-2350-230-12
TABLE 2-16. BORESIGHTING WHITE LIGHT/INFRARED SEARCHLIGHT
STEP PROCEDURE
WARNING: DO NOT look into searchlight beams. Serious eye damage can result.
1 Start vehicle engine and run at fast idle (table 2-3 or 2-4. 1).
CAUTION: DO NOT operate searchlight without engine running.
2 Select a target (preferably a boresight panel) as near 1, 200 meters as possible.
3 With all superelevation removed from fire control system, lay aiming cross of M119
telescope on center of boresight panel. Center the bubble on the elevation quadrant
with the micrometer knob.
4 Apply plus 5 mils on elevation ’quadrant and manually elevate gun until bubble is
centered.
5 Place searchlight main control box LOCAL/REMOTE switch (10, fig. 2-36) in
LOCAL position.
NOTE. When switch is in REMOTE position. commander has control of searchlight

with his remote control box.
6 Turn BEAM SPREAD/COMPACT switch (7, fig. 2-36) to COMPACT position.
7 Turn VISIBLE/INFRARED/OFF switch (9, fig. 2-36) to VISIBLE position. Green

LAMP ON light (8, fig. 2-36) and searchlight will ignite.
8 Loosen 4 screws (2, fig. 2-35) securing searchlight to support.
9 Align searchlight until maximum intensity of searchlight beam is horizontally on

center of boresight panel and tighten 4 screws.
10 Back off the 2 jam nuts (4, fig. 2-35) on the elevating adjusting screw (6, fig. 2-35).
11 Turn adjusting screw (6, fig. 2-35) and raise or lower searchlight until beam is
vertically on boresight panel Tighten 2 jam nuts (4, fig. 2-35).
12 Tighten Jack screw (8, fig. 2-35) firmly against gun shield and lock with jam nut
(7, fig. 2-35).
13 Turn VISIBLE/INFRARED/OFF switch to OFF position.
CAUTION: DO NOT shut VEHICLE MASTER switch off until after searchlight
thermostatically controlled blower motor has stopped.
ALTERNATE METHOD (REFER TO FIG. 2-37)
14 Position the tank so the searchlight is facing a vertical surface such as a wall at a
distance of approximately 10 meters (30 feet).
15 Place a cross on the vertical surface approximately 7 feet from the ground and a
second cross 16-1/2 inches above, and 20-41/64 inches left of the first cross.
16 Remove all superelevation from fire control system and place boresight thread on
muzzle end of gun tube and boresight main gun on lower cross (table 2-9).
2-61
C4, TM 9-2350-230-12
TABLE 2-16. BORESIGHTING WHITE LIGHT/INFRARED SEARCHLIGHT - CONTINUED
STEP PROCEDURE
ALTERNATE METHOD (REFER TO FIG. 2-37) - CONTINUED
17 Adjust searchlight (steps 5 through 10) until light beam is centered on upper cross.
Place a reference mark so that top edge of mark just touches the bottom of searchlight
beam. Center the bubble. on the elevation quadrant using the micrometer knob.
18 With searchlight on, apply 5 mils on elevation quadrant and manually elevate gun
until bubble is centered.
19 Adjust searchlight (steps 9 and 10) until bottom of light beam is above and just touching
the reference mark. This technique will converge the light beam and the axis of the
gun at approximately 1, 200 meters.
20 Follow steps 12 and 13 above.
Figure 2-37. (Added) Searchlight boresight target.
2-62
C 10, TM 9-2350-230-12
CHAPTER 3
FIRING PROCEDURE
Section 3-1. MISFIRE, HANGFIRE, AND COOK-OFF, AND IMMEDIATE

ACTION IN CASE OF FAILURE TO FIRE
3-1. MISFIRE, HANGFIRE, AND COOK-OFF of the weapon may result.

CONVENTIONAL AMMUNITION
a. Conditions described below are rarely encountered b. After failure to fire, observe following precautions
when authorized, properly maintained ammunition is fired until round has been removed from weapon:
in properly maintained and operated weapons. To avoid
injury to personnel and damage to equipment, however, (1) Keep weapon trained on target, and all
it is important that those concerned understand the personnel clear of muzzle and path of recoil.
nature of these conditions and be familiar with preventive
and corrective procedures. (2) Make two additional attempts to fire.
WARNING: In event of failure to fire, keep weapon (3) Wait two minutes after third attempt to fire.
trained on target. Have personnel stand clear of muzzle Open breech. Clean firing probe. Close
and path of recoil. Chambered rounds should be fired or breech.
removed from weapon within five minutes. In case of an
(4) Attempt to fire again.
explosive round chambered in a hot weapon, which can
neither be fired nor removed within five minutes, (5) If weapon is hot and round cannot be
evacuate personnel from area for period of two hours. removed within five minutes, elevate weapon
to approximately 19 degrees and evacuate all
(1) Misfire. A misfire is a failure of a round to fire
personnel from area Wait two hours.
after initiating action is taken. The failure may
be due to a faulty firing mechanism or a faulty
NOTE. After waiting period, weapon may be
element in the propelling charge explosive
carefully relocated to a remote position. To
train. A misfire in itself is not dangerous;
relocate, lower cannon tube and engage traverse
however, it cannot be immediately
lock.
distinguished from a delay infunctioning of the
weapon firing mechanism or from a hangfire.
(6) Request EOD or direct support ammunition
Misfires must be treated as delayed firings,
maintenance personnel to remove round or
therefore, until otherwise determined.
cannon with round.
(2) Hangfire. A hangfire is a delay in the
(7) If removed round is determined to be at fault,
functioning of a propelling charge explosive
or was removed from hot cannon, set it aside
train at the time of firing. The delay, though
for disposal by authorized munitions
unpredictable, ranges from a fraction of a
personnel.
second to several minutes. A hangfire cannot
be distinguished immediately from a misfire. (8) Have firing mechanism corrected, if at fault.
After mechanism is corrected, round may be
(3) Cook-off. A cook-off is a functioning of any or
reloaded and fired.
all of the explosive components of a round
chambered in a hot weapon. If the primer or
the propelling charge should cook-off, the CAUTION: Do not reuse rounds extracted
projectile may be fired from the weapon with from weapons by ramming. Extraction difficulty
normal velocity even without attempting to fire may have been caused by some nonstandard
the primer by actuating the firing mechanism. condition in the ammunition; also, the fuze may
Should the bursting charge explosive train have been damaged during ramming process.
cook-off, injury to personnel and destruction
3-1
C 10, TM 9-2350-230-12
c. Observe the following safe temperature limits when c. Cook-Off. A cook-off is the firing of the chambered
loading or firing conventional ammunition: round due to the heat of a hot barrel and not due to the
actuating of the machine gun.
For all models except HE-T cartridge XM657E2: d. Stoppage. Stoppage is any interruption in the cycle
Upper limit......................................... +125°F of operation caused by faulty action of the machine gun
Lower limit......................................... -40°F of ammunition.
For HE-T cartridge XM657E2 only: 3-2. Immediate Action In Case of Failure to Fire
Upper limit......................................... +125°F
Lower limit......................................... +40°F 152MM Gun/Launcher - Table 3-1.
7.62MM Machine Gun - Table 3-2.
d. Observe the following precaution relative to duds: Cal. 50 Machine Gun - Table 3-3.
Missile- - - - - - - - - - Table 3-4. 1.
WARNING: Do not touch, move or otherwise handle
duds. Notify EOD of location. 3-2. 1 SHILLELAGH MISSILE
3-1.1. Misfire, Hangfire, Cook-Off, and Stoppage - a. Firing temperature limits for the SHILLELAGH
Cal. .50 and 7.62MM Machine Guns missile are +1450F to -250F.
b. Loading, launching, and unloading procedures
a. Misfire. A misfire is a complete failure to fire. It
are contained in table 3-4. 1.
must be treated as a hangfire until such possibility has
been eliminated. c. The M29 and M29A dummy missiles simulate the
SHILLELAGH missile in size, weight, center of gravity,
b. Hangfire. A hangfire is a delay in the functioning of
and "feel" The dummy missile is completely inert and
a propelling charge. The time interval prescribed in table
contains no explosives. It is provided as a "drill" round for
3-2 will be observed after a failure to fire.
training in loading the SHILLELAGH missile into the gun-
launcher.
3-2
C9, TM 9-2350-230-12
TABLE 3-1. IMMEDIATE ACTION IN CASE OF FAILURE TO FIRE -

152MM CONVENTIONAL AMMUNITION
1 Attempt to fire with firing button on elevation handwheel. 2-19
WARNING: Remove blasting machine from bracket and operate from

loader’s or commander’s seat. If blasting machine must be operated in
bracket, be careful to stand clear of gun recoil.
2 Attempt to fire 152MM conventional round (third time) by removing safety 3-1/F
pin and turning blasting machine handle vigorously 3 to 5 times.
3 Push SAFE/READY switch to SAFE position if third attempt to fire fails 3-1/A
CAUTION: Wait at least 2 minutes after step 3, remaining clear of

breech in case round ignites and gun-launcher recoils.
4 Place ejector lever in non-eject (up) position 3-1/D
CAUTION: Make certain ejector lever is in non-eject (up) position

before opening the breech. If in eject position, the ejector would cut open
case upon breech opening allowing propellant particles to escape into turret,
creating an extremely hazardous condition.
5 Open breech electrically or manually (table 3-4).
6 Depress release handle located at forward edge of loading tray bracket, 3-1/D
and hold in depressed position. If only one man is available to remove
round, insert a small (3/16") piece of wood between loading tray detent
release plunger and housing assembly detent release pin, and completely
open breech chamber. The wood will permit use of both hands to remove
round.
7 Grasp round and slide rearward onto loading tray 3-1/E
8 Release detent release handle and return round to rack 3-1/D
9 Return round to ammunition personnel as soon as possible for disposition.
10 Before resuming firing procedure after misfire, check firing probe 3-1/E
contact and clean if necessary to assure proper operation.
11 Report misfires, hangfires, and other malfunctions in accordance with

unit safety SOP.
3-2.1
TM 9 2350-230-12
TABLE 3-2. IMMEDIATE ACTION IN CASE OF FAILURE TO FIRE - 7.62-MM MACHINE GUN,
COOL WEAPON
When a stoppage occurs (failure to fire) before completing a 200-round
series (starting from a cool machine gun), perform the operations
listed below.
1 Wait five seconds in the event of hangfire.
WARNING: Keep weapon trained on target.
2 Charge weapon fully (if possible) to sear position and attempt to fire 3-5/D
next round (table 3-5).
3 If the weapon fails to fire, charge weapon again and place safety in 3-5/E
S (safe) position.
4 Open cover assembly and remove belted ammunition. 3-5/F
5 Open feed tray and remove live ammunition or spent cartridge and links 3-5/E
from weapon chamber and/or immediate area.
6 Slide safety into F (fire) position and hand-function weapon one cycle. 3-5/E
7 Load and attempt to fire, if weapon still fails to function properly, in-
spect for cause of stoppage, refer to troubleshooting procedure (table
5-1, steps 32 through 42).
HOT WEAPON
When stoppage occurs (failure to fire), after a burst of approximately

200 rounds fired either spasmodically or continuously within two
minutes, perform the operations listed below.
WARNING: The danger of an open-cover cook-off exists when

weapon is hot. Immediate action must be applied within 10 seconds.
Keep weapon trained on target, remain clear of barrel and do not
open cover during this period.
9 If firing cannot be resumed, charge weapon to sear position and slide 3-5/E
safety to S (safe) position.
WARNING: Allow the weapon to cool at least five minutes before

attempting to open cover assembly.
10 Open cover, clear and inspect weapon for cause of stoppage; refer to
troubleshooting procedure (table 5-1 , steps 32 through 42).
3-2.2 (Pages 3-2. 3 and 3-2. 4 Deleted)
3-2.2
TM 9-2350-230-12
TABLE 3-3. IMMEDIATE ACTION IN CASE OF FAILURE TO FIRE-CAL..50 MACHINE GUN M42,HB
COOL WEAPON
When a stoppage occurs (failure to fire) before completing 150 rounds,
perform operations listed below.
1 Wait 5 seconds in the event of a hangfire.
WARNING: Keep weapon trained on target.
2 Retract bolt and push retracting slide handle forward. 3-8/E

3 Depress bolt latch release to return bolt to battery position. 3-8/D
4 Depress trigger and attempt to fire. 3-8/F
5 If weapon still fails to fire, wait 5 seconds, retract bolt (engage with 3-8/F
bolt latch) and return handle forward.
NOTE: If bolt latch release is in a locked (depressed position), the

bolt will be forward and another round could be chambered.
6 Open cover assembly and remove belted ammunition 3-8/B
WARNING: Inspect to insure weapon is clear.

7 Check to determine cause of stoppage; refer to troubleshooting procedure

HOT WEAPON
When stoppage occurs (failure to fire) after firing approximately 200
rounds, either spasmodically or continuously within 2 minutes, per-
form the operations listed below:
WARNING: The danger of a cook-off exists when barrel is hot.

Immediate action must be applied within 10 seconds. Keep weapon
trained on target, remain clear of barrel and do not open cover
during this period.

9 Attempt to fire by depressing bolt latch release and trigger at same time. 3-8/D
Weapon should fire automatically.
10 Follow steps 5 through 7 above.
11 If the bolt cannot be retracted when applying immediate action or a
misfire occurs after intentional cessation of firing and bolt is forward
at time trigger is pressed, the bolt must remain locked in battery
position (do not open the cover assembly). ALLOW THE WEAPON TO
COOL AT LEAST 5 MINUTES to guard against a cook-off. After wait-
ing specified time (5 minutes), follow steps 1 through 7 above.
3-3
TM 9-2350-230-12, C11
Section 3-2. 152MM GUN-LAUNCHER
3-3. Firing Procedure breech cavity when gun returns to battery and contacts
The following table and illustrations provide the in-battery limit switch. A delay of 1.7 seconds before
152MM gun-launcher conventional ammunition and the breech opens provides time required for the
missile firing procedure. scavenging blast. The pressure gage indicates pressure
NOTE. Before operation, the crew must be in the system, in psi and number of rounds remaining
familiar with the location and operation of all controls without further compressor operation.
(figs. 2-19, 20, 23, 25 and 3-r through S-4). e. Operation of the system is explained in
figures 3-2.3 and 3-2.4. Preventive maintenance checks
3-3.1. Deleted. and services are covered in table 4-1.
3-3.2. Closed Breech Scavenging System 3-3.3. High Voltage Power Supply for
Conventional Mode Firing
a. M551 vehicles equipped with M81El gun/
launcher incorporate a closed breech compressed air A high voltage power supply provides a -120 volt pulse
scavenging system. The system is used with both when firing the gun-launcher in conventional mode to
missile and conventional ammunition to scavenge eliminate the possibility of a misfire due to firing probe or
breech and gun tube of debris and gases. ammunition contamination. When the FIRE CONTROL
b. The system consists of a four-stage air selector is in CONV position, the + 28 volt vehicle power
compressor, two air cylinders, pressure gage, pressure to the firing probe is interrupted and the -120 volt power
regulator, on-off switch, solenoid discharge valve with supply is energized. When the firing trigger is squeezed
manual discharge lever, and attaching hoses and fittings. the 120 volt electrical pulse is sent to the firing probe.
c. Compressor operation is automatically
controlled by a pressure control switch which energizes 3-3. 4. Ammunition Detent Identification
the compressor motor when pressure in the system falls a. The ammunition detent assembly which is
below 2800 (+ 100) pot, and de-energizes compressor referred to as "early design" is Type I detent assembly;
motor when pressure reaches 3100 (+100) pi. An the "late design" is Type H detent assembly.
electrical interlock prevents operation of the compressor b. The Type m detent assembly is identified in
when selector control is in missile mode, to avoid one or all of the following manners:
possible voltage drop in the vehicle electrical system (1) The designation "Type II" stamped on
during launching and tracing. face of detent housing cover.
d. Air (regulated to 630 psi regardless of (2) Type m detent shaft has a smaller
system pressure) is discharged into the closed diameter (1/4-inch) than Type I and II detent shafts (3/8-
inch).
(3) Decal positioned above detent
assembly stating "TYPE 3 AMMUNITION DETENT
INSTALLED".
3-4
TM 9-2350-230-12, C5
TABLE 3-4. LOADING, FIRING, AND UNLOADING 6UN-LAUNCHR WITH CONVENTIONAL ROUND
WARNING: Do not chamber ammunition until immediately before firing.

Ammunition left too long in a hot weapon may result in hazardous
conditions. fire or remove ammunition within five minutes of
chambering. Refer to Section 7-2 for instructions and warnings on
handling ammunition before proceeding to fire.
PREPARATION FOR FIRING
(table 4-1, steps 21, 22, 23 and 45 through 52).
2 Check safe-to-fire indicator rod to be sure it is within safe range. 3-2
3 Check recoil mechanism replenisher system reservoir for proper
fluid level 3-2
4 Remove 152MM gun-launcher muzzle plug if installed. 1-1/4
5 Check boresight alignment of gun-launcher, 7. 62MM machine gun and
sighting and fire control equipment (table 2-9). Be sure machine
gun cover is closed and locked.
6 Turn vehicle MASTER SWITCH on and start engine. 2-10
7 Turn TURRET CONTROL POWER switch on (non-stabilized mode),
turn STAB switch on (if stabilized mode is desired) (par. 2-5).
8 Turn FIRE CONTROL selector to CONV position. The corresponding
lamp above the selector will illuminate. 2-19
9 Turn turret ventilating fan on. 2-20/E
NOTE: The turret fan motor circuit is interrupted when gun launcher
leaves "in-battery" position (after a successful missile or conventional
firing) and remains interrupted until the completion of scavenging cycle.
9.1 On vehicles with C02 scavenging system, remove bottle valve safety 3-2.2
pin and secure operating handle in open position with clip. Weigh
CO2 bottle after firing every ten (10) rounds.
9.2 On vehicles equipped with closed breech scavenging system, make sure 3-2.4
shut-off valve is open (handle parallel to valve), and turret selector
switch is on "CONV". Turn compressor switch ON; compressor
should run if gage reads less than 2800 psi. Momentarily trip
scavenger by means of lever on air solenoid valve to check operation
of scavenger system.
OPENING BREECH ELECTRICALLY AND LOADING

CAUTION: Prior to loading, make sure tube, coupling, and breech
chamber are clear do burning or smoldering residue.
10 Place loader’s control box SAFE/READY switch in SAFE position. 3-1/A
11 Position breech actuator handle lever to engage one of 8 slots in
rear cover. 3-1/B
12 Open breech by holding CLOSE/OPEN switch on loader’s control box
to OPEN position until breech is fully opened. 3-1/A
13 Remove round from stowage rack. Remove ballistic protective cover. 3-1/E a
Place round on loading tray. Remove neoprene barrier bag while 3-3
loading round into gun tube. Shove round firmly into tube until
detent pin is engaged.
WARNING: Use only correct lots of ammunition and handle with care. 7-2, 3
Avoid striking fuze or primer. (Refer to Section 7-2)
14 Place ejector mechanism lever in non-eject (up) position. 3-/D
3-5
TM 9-2350-230-12, C11
TABLE 3-4. LOADING, FIRING, AND UNLOADING GUN-LAUNCHER WITH CONVENTIONAL ROUND - CONTINUED
CAUTION: Make certain that ejector mechanism lever is in non-eject 3-1/D

(up) position. and ERROR and ALIGN levers are in down (left) position.
15 Close breech by holding CLOSE/OPEN switch on loader’s control box 3-1/A
to CLOSE position, until breech is fully closed.
OPENING BREECH MANUALLY AND LOADING
17 Position breech actuator handle lever to engage slot in end of spindle
visible at center of handle casting. 3-1/C
WARNING: Do not actuate breech electrically while breech actuator
handle is engaged for manual operation.
18 Open breech by turning breech actuating handle counterclockwise
until mechanical stop is reached. 3-1/C
20 Close breech by turning breech actuator handle in clockwise
direction until contacting mechanical stop. 3-1/C
FIRING
21 Check safe-to-fire indicator rod to be sure it is within safe range. 3-2
22 Place SAFE/READY switch on loader’s control box in READY 2-25 and
position. Loader’s and gunner’s READY lamps will illuminate. 3-1/A
CAUTION: If lamps do not illuminate, refer to Troubleshooting
Procedure (table 5-1, step 17).
WARNING: When firing, be alert to any evidence of smoke and/or

flame from tube lock key or detent assembly vent. If this occurs,
stop firing immediately and notify supporting maintenance.
WARNING: Personnel should remain clear of breech during recoil

of gun-launcher. When more than normal complement of ammunition
is to be fired-in rapid order, expansion of pressurized hydraulic
fluid in reservoir may cause fluid to spray from pressure relief
valve on top of reservoir. Check reservoir fluid level after every
thirty rounds (fig 3-2).
A. Firing Gun-Launcher When Operating Turret Electrically.

23 Fire weapon by pressing trigger- on gunner’s handle or depressing 2-19 and
palm switch and pressing trigger on commander’s handle. 2-21/9
NOTE: The scavenging system will automatically evacuate breech

and gun -tube of gas and combustible case debris during recoil/battery
cycle. On closed breech scavenging system, use manual discharge
lever with breech closed.
3-6
TM 9-2350-230-12, C10
TABLE 3-4. LOADING, FIRING, AND UNLOADING ,GUN-LAUNCHER WITH CONVENTIONAL ROUND - CONTINUED
FIRING -- Continued
B. Firing Gun-Launcher When Operating Turret Manually.
24 Fire weapon by pressing firing button on gunner’s manual elevation 2-19
handwheel.
25 In case of power failure, fire round with blasting machine by twisting 3-1/F
handle vigorously clockwise and holding in maximum clockwise
position until weapon has fired.
CAUTION: Do not place SAFE/READY switch in SAFE position 3-1/A
until breech is in the fully open position to prevent interruption
of breech cycling. (Vehicle serial numbers 2 and 4 through 58).
26 If additional rounds are required for firing mission, place loader’s 3-1/A
control box SAFE/READY switch in SAFE position after breech
is fully open. Reload, close breech, then repeat firing procedure
above.
WARNING: For immediate action in case of failure to fire,
refer to Section 3-1 and table 3-1.
REMOVAL OF LIVE CONVENTIONAL ROUND
Refer to table 3-1.
AFTER FIRING
27 Place SAFE/READY switch on loader’s control box in SAFE position. 3-1/A
28 Close breech electrically or manually.
29 Turn FIRE CONTROL selector to OFF position. 2-19
30 Turn TURRET CONTROL POWER switch off if system is no longer 2-19 and
required and engage turret traverse lock if vehicle is to be moved. 2-20/C
31 Turret ventilating fan may be turned off when clear of fumes. 2-20/E
32 On vehicles through. S/N699, release bore scavenging system CO2 3-2. 2
bottle valve operating handle clip and install safety pin (closed’
position).
32.1 On vehicles after S/N699, turn compressor switch and air valve to 3-1/A
OFF position.
(table 4-1, steps 102, 103, 104, and 119 through 124).
34 Clean and lubricate gun-launcher in accordance with table 5-8. 1.
35 Stow nylon protective ammunition covers. Discard barrier bags. 3-3, 3-3.3
36 Install muzzle plug in gun-launcher muzzle to prevent entry of rain,
dust, or debris.
3-6.1
TM 9-2350-230-12, C6
TABLE 3-4.1. LOADING, LAUNCHING, AND UNLOADING MISSILES IN 152MM GUN-LAUNCHER
PREPARATION FOR LAUNCHING

1 Perform before-operation preventive maintenance checks and services
(Table 4-1 steps 21, 22, 23, and 45 through 52).
2 Check safe to fire indicator to be sure it is within operating range. 3-2
3 Check recoil mechanism reservoir for proper fluid level. 3-2
4 Remove gun-launcher muzzle plug if installed. 1-1/4
5 Turn vehicle MASTER SWITCH on and make certain all indicator and 2-10
warning lights in turret are operative.
6 Check boresight alignment of gun-launcher and sighting and fire control
equipment (Table 2-9). Close and lock cover of 7. 62mm machine
gun.
7 Energize missile sub-system and perform check procedures (Table 2-12).
8 Turn on turret ventilating fan and open bore scavenger shut-off valve. 2-20/E
3-2.4
WARNING If valve is not open, flareback may occur may occur after
missile launching.
NOTE In missile mode, closed breech scavenging system

compressor does not operate. Therefore. make certain
air bottles are at full pressure at beginning of launching
operation. After several missiles have been fired, bottle
pressure can be recharged by switching to "CONV" or
"COAX" mode.
LOADING AND LAUNCHING MISSILES
CAUTION : Due to the design of Shillelagh missile, the following

precautions should be followed: (1) Do not drop missile, (2) Do
not strike missile, especially the warhead against any object
that could dent or gouge the surface, especially the nose cone.
To dent or gouge the surface could result in malfunction.
9 Turn and push TRANSMITTER DOOR control handle to open door, 2-26/14
then turn handle clockwise to lock door open.
10 Place TURRET CONTROL switch located on gun and turret control 2-19
selector to off position.
11 Place FIRE CONTROL switch on gun and turret control selector to off
position.
13 Start vehicle engine and set idle speed to at least 750 RPM.
14 Place TURRET CONTROL switch in POWER position. Indicator light
will illuminate. After approximately 20 seconds, TURRET CONTROL
READY light will illuminate indicating turret control system and
missile system power supply and rate sensors are energized and on
standby.
15 Turn FIRE CONTROL switch on gun and turret control selector to missile 2-19
position. Indicator lamp will illuminate.
3-6.2
TM 9-2350-230-12, C6
TABLE 3-4.1. LOADING, LAUNCHING, AND UNLOADING MISSILES IN 152MM GUN-LAUNCHER -Continued
LOADING AND LAUNCHING MISSILES - Continued

NOTE Missile reticle appears in M119 telescope. PRIME
VOLTAGE and POWER SUPPLY lamps on test checkout panel
glow during warm-up period and GO OUT when sub-system is
warmed up.
16 Position breech actuator handle lever in one of eight slots in breech 3-1/B
mechanism carrier cover.
WARNING Do not operate breech electrically with breech actuator
handle lever engaged in spindle slot (Manual position). Personnel
may be injured by spinning handle. Be sure handle lever is
positioned in one of 8 slots in breech carrier cover.
17 Place rear of ejector trigger lever on loading tray in eject (down 3-1/D
position).
18 Open breech by holding CLOSE/OPEN switch on loader’s control box 3-1/A
until breech is fully open.
19 Remove missile from stowage rack, place on loading tray so that white 3-1/E
index stripe on missile is facing up and firmly shove into breech and 7-3
until detent in gun-launcher breech coupling engages missile.
WARNING Do not attempt to launch HEAT warhead missile with
dented nose cone.
20 Close breech by holding CLOSE/OPEN switch on loader’s control box 3-1/A
in CLOSE position, until breech is fully closed.
NOTE Breech mechanism may be operated manually. Place 3-1/C
loader’s control box switch in SAFE position and position breech
actuator handle lever to engage slot in end of spindle visible at
center of handle. Open breech by turning handle counterclock-
wise until breech is fully open. Close breech by rotating handle
clockwise until breech is fully closed.
21 Move loader’s control box SAFE/READY switch from SAFE to READY 3-1/A
position. Ready lamps on loader’s control box and gunner’s reticle
dimmer box will illuminate.
WARNING When ready lamp on loader’s control box is illuminated,
weapon may be fired by gunner or commander. Personnel must be
clear when gun-launcher recoils. After weapon returns to battery,
breech will automatically open and missile cap will be ejected.
22 Depress palm switch on gunner’s control handle and track target through 2-19 and
M119 or M127 telescope, using cross point in center of missile reticle. 2-23/D
3-6. 3
TM 9-2350-230-12, C10
TABLE 3-4.1. LOADING, LAUNCHING, AND UNLOADING MISSILES IN 152MM GUN-LAUNCHER -Continued
LOADING AND LAUNCHING MISSILES -Continued

NOTE 1. Do not fire missile when terrain obstacles (within
500 meters of the vehicle and directly in line of flight) extend
above the short horizontal mark below the center of the missile
reticle (fig. 2-23D).
2. Vehicle must be stationary during missile firing.
3. The 12 power feature of the M127 telescope can be
used to advantage at medium and extended ranges during night
firings and in hazy weather conditions to obtain clearer target
definition. Under all other conditions the eight power feature
should be used.
23 Launch missile by pressing gun-launcher firing trigger on gunner’s 2-19 and
control handle, and with palm switch depressed continue tracking 2-23/D
target with control handle, keeping missile reticle on target until
missile impact.
WARNING After trigger is pressed there is a delay of 1 to
2-1/2 seconds before missile ignites and gun-launcher recoils.
After counterrecoil, opening of breech will be delayed 1. 7
seconds while scavenging system is actuated.
24 When operating turret manually, track target with gunner’s manual 2-19
controls and launch missile by pressing firing button on elevation
handwheel. Continue tracking target until missile impact.
25 After launching missile, and before reloading, place loader’s control 3-1/A
box SAFE/READY switch in SAFE position.
IMMEDIATE ACTION IN CASE OF FAILURE TO LAUNCH
26 Attempt to launch (second time) with firing trigger on control handle. 2-19
WARNING Do not attempt to launch missile with blasting machine.
27 Attempt to launch missile (third time) with firing button on elevation 2-19
handwheel.
28 Move SAFE/READY switch to SAFE position if third attempt to launch 3-1/A
fails.
WARNING Wait at least 10 minutes remaining clear of breech in
case missile ignites and gun-launcher recoils. (This wait may be
reduced to 4 minutes under combat conditions).
29 Place ejector lever in non-eject (up) position. 3-1/D
CAUTION Make certain ejector lever is in non-eject (up) position
before opening breech. Ejector would attempt to eject whole
missile and would be damaged.
3-6.4
TM 9-2350-230-12, C10
TABLE 3-4.1. LOADING, LAUNCHING, AND UNLOADING MISSILES IN 152MM GUN-LAUNCHER - Continued
IMMEDIATE ACTION IN CASE OF FAILURE TO LAUNCH - Continued

30 Open breech electrically or manually (steps 18 and 20).
31 Depress detent release handle located at forward edge of loading tray 3-1/D
bracket and hold in depressed position.
32 Grasp guided missile and slide rearward onto loading tray. 3-1/E
DO NOT TOUCH MISSILE FIRING CONNECTOR OR DIAPHRAGM.
33 Release detent release. Remove missile from weapon. 3-1/D
34 In combat situations, dispose of missile immediately.
In non-combat situations, cover the aft end of the missile with 2 layers
of aluminum foil, extended over the rim of the aft cap, and secure the
foil. Tag the missile with the following caution: "Misfired Missile
Handle With Caution;" place missile in missile container; tag outside
of container with the same caution, and evacuate through normal
ammunition supply channels.
35 Before resuming firing procedure after misfire, check firing mechanism 3-1/E
contact and clean if necessary to assure proper operation.
36 Report misfires, hangfires, and other missile malfunctions in accordance
with unit safety standard operating procedures.
AFTER FIRING
37 Place SAFE/READY switch on loader’s control box in SAFE position.

38 Close breech electrically or manually.
39 Turn fire control selector to OFF position.
40 Turn TURRET CONTROL POWER switch off as system is no longer
required and engage turret traverse lock.
41 Close transmitter door and turn handle to lock. 2-26/14
42 Turn turret ventilating fan off when vehicle is clear of fumes. 2-20/E
43 Close bore scavenger shut-off valve. 4-2
(table 4-1, steps 102, 103, 104, and 119 through 124).
45 Clean and lubricate gun-launcher in accordance with table 5-8. 1.
46 Insert plug in gun-launcher muzzle to prevent entry of rain, dust, or
debris.
(3-6.6 blank)/3-6.5
TM 9-2350-230-12, C9
Figure 3-1. 152MM gun-launcher controls
3-7
TM 9-2350-230-12, C9
CHECKING RESERVOIR FLUID LEVEL DECREASING PRESSURE

WITH GUN/LAUNCHER ELEVATED TO 265 MILS, OBSERVE EXCEPT IN CASE OF AUTOMATIC VALVE MALFUNCTION,
HYDRAULIC FLUID LEVEL IN RESERVOIR SIGHT GAGE. RELIEF OF HIGH PRESSURE IS AUTOMATIC ON LATER
LEVEL MUST BE BETWEEN "REFILL" AND "1 QUART" VEHICLES. ON EARLY VEHICLES (OR IN CASE OF VALVE
CROSS LINES. ADD OR DRAIN FLUID AS REQUIRED. MALFUNCTION) OPEN BLEED VALVE SLIGHTLY UNTIL
INDICATOR ROD MOVES INTO OPERATING RANGE, THEN
CAUTION: WHEN ADDING FLUID, AVOID CLOSE VALVE.
DAMAGING FLUID FILTER (IN FILL OPENING)
WITH SPOUT OF FILLER CAN. INCREASING PRESSURE
ACTUATE HAND REPLENISHER PUMP HANDLE (E, FIG. 3-
CHECKING HYDRAULIC PRESSURE 1) UNTIL INDICATOR ROD IS IN OPERATING RANGE.
WITH GUN/LAUNCHER ELEVATED TO 265 MILS, CHECK RECHECK RESERVOIR FLUID LEVEL, AS PREVIOUS
POSITION OF INDICATOR ROD (SEE INSET). ROD MUST CHECK MAY NOT BE ACCURATE IF PRESSURE WAS
BE IN "OPERATING RANGE" TO RETURN GUN TO LOW.
BATTERY. CAUTION: IF RECOIL MECHANISM HAS BEEN
WARNING: DO NOT FIRE IF LOW FLUID DISASSEMBLED, OR IF GUN MOUNT HAS NOT
GROOVE PROTRUDES BEYOND END OF BEEN EXERCISED RECENTLY, BELLEVILLE
BUSHING, OR IF END OF ROD 15 RECESSED WASHERS IN RECOIL MECHANISM MAY NOT
INTO BUSHING. INCREASE OR DECREASE HAVE ATTAINED PROPER "SET", AND ROD MAY
PRESSURE TO BRING ROD INTO OPERATING NOT RETURN TO OPERATING RANGE AFTER
RANGE. FIRING. CHECK ROD BETWEEN ROUNDS, USING
HAND PUMP AS REQUIRED TO MOVE ROD INTO
OPERATING RANGE FOR THE FIRST SEVERAL
ROUNDS FIRED.
WE 66573
Figure 3-2. Checking and adjusting 152MH gun-launcher recoil mechanism
3-8
TM 9-2350-230-12, C4
Figure 3-2.1. (Added) 152MM gun-launcher bore and breech chamber scavenging system
Figure 3-2.1.1.........Deleted
3-8.1
TM 9-2350-230-12, C4
STEP PROCEDURE
. FULL CO2 BOTTLE WEIGHTS VARY, THEREFORE,
MAKE CERTAIN OF BOTTLE WEIGHT WHEN
RECEIVED. IF NOT LEGIBLE, WEIGH BOTTLE
AND RECORD WEIGHT
REMOVAL
1 RELEASE CLIP SECURING C02 BOTTLE CARRYING
HANDLE IN THE VALVE HANDLE NOTCH (OPEN
POSITION).
2 INSTALL SAFETY PIN TO SECURE VALVE
HANDLE IN THE CLOSED POSITION.
3 OPEN BREECH AND BLEED OFF LINE PRESSURE
BY PULSING THE LOADER’S BREECH CHAMBER
SCAVENGE REPEAT SWITCH (A, FIG. 3-1) UNTIL
LINE PRESSURE IS DEPLETED.
CAUTION: FAILURE TO BLEED OFF LINE
PRESSURE WILL MAKE IT
IMPOSSIBLE TO CONNECT
PRESSURIZED LINES AT ASSEMBLY
UNLESS FITTING ARE REMOVED. IF
THIS IS NECESSARY, DO SO WITH
CAUTION, KEEPING FACE AWAY TO
PROTECT FROM C02 BLAST
4 SEPARATE HOSE QUICK-DISCONNECTOR FROM
CO2 BOTTLE ADAPTER
5 RELEASE RETAINING STRAP AND REMOVE
BOTTLE FROM MOUNTING STRAP.
WEIGHING
6 HOOK SCALE ONTO C02 BOTTLE VALVE AND
WEIGH CONTENTS.
NOTE: REPLACE BOTTLE IF WEIGHT HAS

DECREASED FOUR POUNDS OR MORE.
INSTALLATION
7 REMOVE SPARE C02 BOTTLE WITH ADAPTER
FROM STOWAGE BRACKET AND INSTALL.
REVERSE REMOVAL PROCEDURE, FOLLOWING
STEPS 5, 4, 2, AND 1.
8 SECURE EMPTY BOTTLE IN SPARE STOWAGE
BRACKET.
NOTE REMOVE HOSE ADAPTER FROM EMPTY
C02 BOTTLE FOR USE ON REPLACEMENT
BOTTLE AND TURN IN FOR
REPLACEMENT AS SOON AS POSSIBLE.
Figure 3-2.2. (Added) Removal/weighing/installation of gun-launcher bore and breech chamber scavenging system CO2
bottle
3-8.2
TM 9-2350-230-12, C6
CLOSED BREECH SCAVENGING GROUP ON GUN/LAUNCHER
M551 VEHICLES EQUIPPED WITH M81E1 GUN/LAUNCHER 6. WITH PRESSURE ABOVE 630 PSI, MOMENTARILY
INCORPORATE A CLOSED BREECH SCAVENGING ACTUATE MANUAL DISCHARGE LEVER (FIG. 3-2.4)
SYSTEM. (FOR DESCRIPTION OF THE SYSTEM, REFER TO CHECK OPERATION OF SYSTEM. (SINCE
TO PARAGRAPH 3-3.2). DISCHARGE PRESSURE IS REGULATED, OPERATION
OPERATING PROCEDURE IS SAME AT ANY GAGE PRESSURE ABOVE 630 PSI.)
1. CHECK TO ASSURE THAT GUN/LAUNCHER IS CLEAR.
2. OPEN AIR SHUTOFF VALVE (FIG. 3-2.4). NOTE: COMPRESSOR SHUTS DOWN FOR
3. START VEHICLE ENGINE AND SET THROTTLE AT APPROXIMATELY 10 SECONDS EVERY 25-35 MINUTES TO
FAST IDLE (TABLE 2-9). DUMP ACCUMULATED MOISTURE. THIS IS NORMAL, NOT
4. TURN TURRET CONTROL POWER SWITCH "ON" AND A MALFUNCTION.
GUN AND TURRET SELECTOR SWITCH TO "COAX"
OR "CONV". (SCAVENGER SYSTEM OPERATES IN PRESSURE RECOVERY RATE
"MISSILE" MODE, BUT COMPRESSOR DOES NOT.) APPROXIMATE RECOVERY RATE, BASED ON
5. TURN COMPRESSOR SWITCH "ON". COMPRESSOR COMPRESSOR OPERATING NORMALLY AND NO LEAKS
SHOULD OPERATE IF PRESSURE IS LESS THAN 2800 IN SYSTEM, IS AS FOLLOWS:
(*100) PSI, AND SHOULD SHUT OFF WHEN 0 - 800 PSI 27 TO 30 MINUTES
PRESSURE REACHES 3100 (*100) PSI. 800 - 3100 PSI 70 MINUTES
(33 PSI PER MINUTE)
COMPRESSOR AIR FILTER AND ODDMENT COMPRESSOR ON/OFF SWITCH

STOWAGE BOX WE 120681
Figure 3-2.3. Closed breech scavenger system operation (1 of 2).
3-8.3
TM 9-2350-230-12, C6
A. SOLENOID AND MANUAL DISCHARGE VALVE.. B. AIR COMPRESSOR
C. REAR CYLINDER BLEED PLUG. D. FRONT CYLINDER BLEED PLUG.
WE 12069
Figure 3-2.4. Closed breech scavenger system operation (2 of 2).
3-8.4
TM 9-2350-230-12, C 10
Figure 3-3. 152MM gun-launcher conventional ammunition and missile stowage
3-9
TM 9-2350-230-12, C 10
Figure 3-3.1. Turret 3 round vertical ammunition rack adjustment

and hill ammunition stowage
3-10
TM 9-2350-230-12, C4
A. VERTICAL RACK NOSE CONE SUPPORT INSTALLED FOR XM409, XM411, XM625 AND XM657 AMMUNITION.
B. NOSE CONE SUPPORT INVERTED TO FIT XM617 AMMUNITION.
C. HORIZONTAL RACK NOSE CONE SUPPORT INSTALLED FOR XM409, XM411 AND XM625 AMMUNITION.
D. NOSE CONE SUPPORT REVERSED TO FIT XM617 AND XM657 AMMUNITION.
REMOVAL/INSTALLATION FOR HORIZONTAL RACKS
REMOVE TWO NUTS AND SCREWS, REVERSE NOSE CONE SUPPORT, AND INSTALL USING SAME SCREWS
AND NUTS.
REMOVAL/INSTALLATION FOR VERTICAL RACKS
LOOSEN STRAP, INVERT NOSE CONE SUPPORT AND FASTEN STRAPS.
NOTE. WHEN NOT IN USE, VERTICAL RACK NOSE CONE SUPPORTS ARE STOWED IN TURRET EXTERIOR RACK.
WE 11958J
Figure 3-3.2. Reversible nose cone supports - conventional ammunition racks
STOWAGE STRAPS ARE PROVIDED FOR

STOWAGE OF AMMUNITION PROTECTIVE
COVERS IN THREE PLACES BENEATH HULL
LEFT AMMUNITION RACKS AND ONE PLACE
BENEATH HULL RIGHT AMMUNITION RACK.
ALL COVERS NOT IN USE ARE TO BE
STOWED AT THESE LOCATIONS.
WITH NO AMMUNITION ON BOARD THE

COVERS ARE STOWED 8 IN EACH OF THE
LEFT RACK LOCATIONS AND 10 BENEATH
THE RIGHT RACK. WITH FULL LOAD OF
AMMUNITION (29 ROUNDS) THE SPARE
COVERS ARE STOWED I IN EACH LEFT RACK
LOCATION, AND 2 BENEATH THE RIGHT
RACK.
WE 11962
Figure 3-3.3. Ammunition protective cover stowage (effective vehicle S/N 700)
3-10.1
TM 9-2350-230-12, C10
CONVENTIONAL ROUND REMOVAL PROCEDURE
WARNING: KEEP CLEAR OF MUZZLE, AND DO

NOT HAMMER ROUND.
1. ASSEMBLE M15 CLEANING STAFF 7309228 TO

RAMMER 8769486.
2. STATION SECOND CREW MEMBER IN TURRET TO
DEPRESS DETENT RELEASE LEVER DURING
RAMMING OPERATION, AND TO RECEIVE ROUND AS
IT EMERGES FROM CHAMBER.
3. SLIDE STAFF ASSEMBLY GENTLY DOWN GUN-
LAUNCHER BORE UNTIL SEATED ON OGIVE OF
PROJECTILE. EXERT STEADY PRESSURE UNTIL
ROUND IS CLEAR OF CHAMBER.
WE 66700 5
Figure 3-4. Removing a stuck conventional round from 152MM gun-launcher
Section 3-3. 7.62MM MACHINE GUN

3-4. Firing Procedure
NOTE. Before operation the crew should be
The following tables and illustrations provide 7.62MM familiarized with the location and operation of all controls
machine gun firing procedure. (figs. 2-19, 20 and 3-5 through 3-7).
TABLE 3-5. LOADING, FIRING, AND UNLOADING 7.62MM MACHINE GUN


2 Align machine gun with gun-launcher (table 2-9).
4 Make certain FIRE CONTROL selector is in OFF position. 2-19
5 Open ammunition feed box assembly door and load ammunition. 3-5/A
LOADING AND CHARGING
6 Push forward on cover latch rod assembly and raise cover. 3-5/B
7 Raise feed tray and slide safety to F (fire) position. 3-5/C
8 Pull charger handle rearward and charge (cock) machine gun. Inspect 3-5/D
chamber.
9 Slide safety to S (safe) position and lower feed tray. 3-5/E
WARNING: Make certain that feed tray is clear of live rounds, spent
brass or links, barrel extension is in rearward position and safety is
in S (safe) position.
10 Place first round of ammunition belt in slot of feed tray with open end of 3-5/F
link loops facing down.
11 Assure that cover latch rod lock is engaged in forward position, then 3-5/B
close cover.
3-10.2
TM 9-2350-230-12, C8
TABLE 3-5. LOADING, FIRING, AND UNLOADING 7.62MM MACHINE GUN, M73 - CONTINUED
FIRING ELECTRICALLY
12 Turn turret ventilating fan on.
WARNING: Without fan, toxic gases may reach dangerous level. 2-20/E
13 Turn TURRET CONTROL POWER switch on. 2-19
14 Turn FIRE CONTROL selector to COAX position. 2-19
15 Slide safety to F (fire) position. 3-5/C
16 A. Firing Gun When Operating Turret Electrically.
Depress palm switch and fire gun by pressing firing trigger on gunner’ s 2-19 and
or commander’s control handle. 2-21/9
B. Firing Gun When Operating Turret Manually.
Fire gun by pressing firing button on gunner’s manual elevation hand- 2-19
wheel.
NOTE. To fire manually, press manual firing trigger on gun. 3-5/D
UNLOADING UNFIRED ROUND
WARNING: For immediate action in case of failure to fire, refer to

table 3-2.
RUNAWAY GUN
NOTE: A runaway gun continues to fire after firing button is

released.
CAUTION: Hold fire on target until feeding of ammunition is stopped,
17 Pull and hold charging handle to the rear to stop firing.
18 Place safety in S (Safe) position and open cover, permitting ammunition
link belt to drop out.
WARNING: Visually check and feel to assure that chamber is clear
of ammunition.
18.1 Locate and correct cause (table 5-1).
REMOVAL OF RUPTURED CARTRIDGE CASE OR LIVE ROUND 3-6
REMOVAL/INSTALLATION OF BARREL 5-11/12
REMOVAL/INSTALLATION OF -FLASH HIDER 5-13
REMOVAL/INSTALLATION OF MACHINE GUN 3-7
AFTER FIRING
19 Place gun safety in S (safe) position. 3-5/E
20 Turn FIRE CONTROL selector to OFF position. 2-19
21 Turn off turret ventilating fan. 2-20/E
22 Push forward on rear of cover latch rod assembly and open cover. 2-5/B
23 Remove ammunition belt from machine gun if ammunition has not been
expended.
WARNING: If ammunition belt has been expended, inspect chamber
for possible live cartridge, spent cartridge case, and/or empty link
and remove.
24 Raise feed tray, slide safety to F (fire) position and pull charger handle 3-5/C, D
rearward until barrel extension is in open position.
25 Pull charger handle rearward, depress manual firing trigger and allow 3-5/D
charger handle to go forward slowly.
26 Place safety in S (safe) position and close cover. 3-5/B, E
27 Perform after operation preventive-maintenance checks and services
3-11
TM 9-2350-230-12, C6
Figure 3-5. 7.62 mm machine gun controls
3-12
TM 9-2350-230-12, C6
STEP PROCEDURE STEP PROCEDURE

1. MAKE CERTAIN SAFETY IS IN SAFE "S" 1. INSERT EXTRACTOR THRCUGH RUPTURED
POSITION. CARTRIDGE INTO BARREL UNTIL COLLET
ENGAGES FORWARD END OF CASE.
2. POSITION TOOL ON CARTRIDGE CASE HEAD
AND PRESS FORWARD TO REMOVE. 2 INSERT ASSEMBLED CLEANING ROD THROUGH
MUZZLE END OF BARREL AND DRIVE
: WARNING INSPECT CHAMBER TO EXTRACTOR AND RUPTURED CARTRIDGE
INSURE PROJECTILE WAS NOT SEPARATED CASE FROM CHAMBER.
FROM CASE DURING REMOVAL.
Figure 3-6. Removing live round of, ruptured cartridge case from 7.62 mm machine gun
REMOVAL INSTALLATION
1. DISCONNECT MACHINE GUN ELECTRICAL LEAD. 3. MATCH KEYS ON GUN WITH KEYWAYS IN MOUNT
2. REMOVE 2 SCREWS, MACHINE GUN MOUNT CAP, AND REVERSE REMOVAL PROCEDLIRE
AND LIFT MACHING GUN OFF MOUNT.
SPENT BRASS EJECTION CHUTE EXTENSION
INSTALL ON MACHINE GUN COVER AS SHOWN IN
ILLUSTRATION, AND TIGHTEN TWO SCREWS.
LOOSEN SCREWS TO REMOVE EXTENSION.
WE 120741
Figure 3-7. Removal/installation - 7.62 mm machine gun
3-13
TM 9-2350-230-12
Section 3-4. CAL. .50 MACHINE GUN, M2, HB
3-5. Firing Procedure NOTE. Before operation the crew should be

The following tables and illustrations provide Cal. familiarized with the location and operation of all controls
.50 machine gun, M2, HB firing procedure. (figs. 3-8 through 3-14).
TABLE 3-6. LOADING, FIRING AND UNLOADING CAL. .50 MACHINE GUN

2 Check headspace and timing. Adjust if required (tables 3-7 and 3-8).
3 Install flash hider. 3-13
4 Install carrier assembly. 3-10
5 Remove ammunition box cover and place box in ammunition tray. 3-8/A
NOTE: The double loop end of ammunition belt must be leading.
LOADING
6 Open machine gun cover and insert double loop end of ammunition in 3-8/B, C
feedway until first round is held by belt holding pawl.
HALF-LOAD GUN
7 Retract the retracting slide handle, pulling bolt all the way to the rear. 3-8/B
Release handle.
8 Position bolt latch release lock to engage bolt latch release when 3-8/D
depressed.
9 Push retracting slide handle all the way forward. 3-8/E
10 Press down on bolt latch release, bolt will go forward. 3-8/D
11 To FULLY LOAD gun, repeat steps 6 through 9.
12 Close gun cover. 3-8/B
SEMI-AUTOMATIC FIRING
13 Turn bolt latch release lock clockwise to allow bolt latch release to be in 3-8/D
raised position. Fire gun by pressing trigger.
WARNING: When bolt latch release and trigger are both held down,
machine gun will fire automatically.
AUTOMATIC FIRING
14 Lock bolt latch release down by engaging in bolt latch release lock. Fire 3-8/D
gun by pressing trigger.
WARNING: For immediate action in case of failure to fire, refer to table 3-3.
3-14
TM 9-2350-230-12, C1
TABLE 3-6. LOADING, FIRING AND UNLOADING CAL. .50 MACHINE GUN - CONTINUED
REMOVING RUPTURED CARTRIDGE CASE 3-9

REMOVAL/INSTALLATION OF BARREL
WARNING: Use asbestos gloves if barrel is hot.
(1) Remove barrel from gun. 5-14/1
(2) Remove carrier assembly and install on spare barrel. 3-10
(3)Remove flash hider and install on spare barrel. 3-13
(4) Install spare barrel. 5-14/1
NOTE: Carrier assembly must be in 5 or 7 o’clock position
on barrel to prevent damage to antenna when cupola Is rotated.
REMOVAL/INSTALLATION OF MACHINE GUN 3-14

AFTER FIRING
15 Raise cover and remove ammunition belt. 3-8/B
16 Close cover. 3-8/B
17 Retract bolt and lock in rearward position. 3-8/D, E
18 Raise cover and inspect chamber. 3-8/B
19 Hold handle, release bolt, and allow bolt to move slowly forward. 3-8/D, E
(table 4-1,step 105).
3-15
TM 9-2350-230-12
Figure 3-8. Cal..50 machine gun, M2, HB, controls
3-16
TM 9-2350-230-12, C4
Figure 3-9. Remove ruptured cartridge case from chamber of cal. .50 machine gun
Figure 3-10. (Superseded) Removal/Installation - cal. .50 machine gun carrier assembly/
3-17
TM 9-2350-230-12
TABLE 3-7. CHECKING AND ADJUSTING HEADSPACE - CAL. .50 MACHINE GUN
NOTE: Headspace must be checked and/or set prior to firing, after

assembling gun and when barrel or any group in the receiver is
replaced.
CAUTION: Improper headspace can cause malfunctioning of the
gun and frequent damage to parts and/or injury to personnel.
1 Raise cover. 3-8/B
2 Retract bolt (approximately 3/8 inch) using retracting slide handle until 5-14
locking lug on barrel locking spring is centered in hole of right side
plate of receiver.
3 Hold bolt in above position and screw barrel fully into barrel extension. 5-/14
NOTE: Should handle be released, the recoiling parts will remain
out of battery position (a separation will exist between barrel
extension and trunnion block).
4 With handle retracted, unscrew barrel two notches (clicks). Release 5-14
handle.
5 Cock machine gun. 3-8/B
NOTE: With machine gun cocked, firing pin is withdrawn into face 3-11
of bolt allowing headspace gage to be inserted into T -slot on bolt.
CAUTION: Do not fire gun when headspace gage is in T-slot.
6 Hold handle, release bolt and allow bolt to return to battery position 3-8/D, E
slowly to prevent bolt slamming.
7 Retract recoiling parts approximately 1/16 inch to insure that locking 3-11
surfaces of breech lock and bolt are in proper contact.
8 Raise extractor. 3-11
9 Insert GO end of headspace gage into center of T-slot between face of 3-11/A
bolt and barrel.
CAUTION: Do not force gage.
10 If GO end of gage enters T-slot, to center ring of gage, and the NO 3-11
GO end will not enter, headspace is correct.
HEADSPACE TOO TIGHT

If GO end of gage will not enter T-slot freely, perform following
procedures:
11 Retract bolt, step 2 above.
12 Unscrew barrel one notch (click). Return parts to battery position. 5-14
13 Retract recoiling parts, step 7 above.
14 Check headspace, step 10 above.
3-18
TM 9-2350-230-12
TABLE 3-7. CHECKING AND ADJUSTING HEADSPACE-CAL. .50 MACHINE GUN - CONTINUED
HEADSPACE TOO LOOSE

If NO GO end of gage enters T-slot, perform following procedures:
15 Retract bolt, step 2 above.
16 Screw barrel into barrel extension one notch (click). Return parts to 5-14
battery position.
17 Retract recoiling parts, step 7 above.
18 Check headspace, step 10 above.
NOTE. If proper headspace adjustment cannot be obtained, notify

Figure 3-11. Checking and adjusting headspace on cal. .50 machine gun, M2, HB
3-19
TM 9-2350-230-12, C10,
TABLE 3-8. CHECKING AND ADJUSTING TIMING - CAL. .50 MACHINE GUN, M2, HB
1 Insure headspace is correct (table 3-7).

2 Cock machine gun. (Retract bolt assembly to rear position and slowly 3-8/E
release to forward position. )
3 Raise extractor 3-12/A
4 Retract bolt sufficiently to insert NO FIRE (0. 116-inch) gage between 3-12/A
trunnion block and barrel extension group. Release retracting slide
handle.
5 Depress the trigger. The firing pin SHOULD NOT RELEASE. In the 3-8/F
event it does release repeat steps 2 and 3.
WARNING Do not attempt to remove back plate unless the bolt
is in forward position. Do not attempt to cock machine gun with-
out the back plate assembled to machine gun.
6 Remove back plate 5-14/4
7 Screw the timing adjustment nut all the way down (counterclockwise) 3-12/B
8 Place the FIRE (0. 020-inch) gage between trunnion block and barrel 3-12/D
extension group. Release retracting slide handle.
9 Attempt to release firing pin by lifting up on rear end of trigger lever 13-12/C
10 Screw up (clockwise) on timing adjustment nut one click at a time and 13-12/C
attempt to release firing pin after each click until the firing pin does
release. When the firing pin does release move the adjusting nut two
more clicks clockwise (up).
11 Replace back plate assembly 5-14/19
12 Repeat steps 2 through 5. The firing pin SHOULD NOT RELEASE.
13 Repeat steps 2 and 3.
14 Place FIRE gage between trunnion block and barrel extension and attempt 3-12/D
to release firing pin by pressing the trigger. The firing pin SHOULD
RELEASE.
NOTE If proper timing adjustment cannot be obtained, notify
3-20
TM 9-2350-230-12
Figure 3-12. Checking and adjusting timing on cal. .50 machine gun M2, HB
3-21
TM 9-2350-230-12
Figure 3-13. Installation/removal - cal. .50 machine gun flash hider
3-22
TM 9-2350-230-12, C6,
REMOVAL
1. DISCONNECT CUPOLA TRAVERSE MECHANISM SWITCH ASSEMBLY QUICK DISCONNECT.
2. REMOVE 4 SCREWS AND SWITCH ASSEMBLY.
3. PULL OUT 2 LOCKING PINS AND REMOVE MACHINE GUN .
4. REMOVE 2 SCREWS AND WASHERS TO REMOVE EJECTION CHUTE AND CLAMP.
INSTALLATION
REVERSE REMOVAL PROCEDURE. REFER TO FIGURE 2-4 FOR INSTALLATION OF PINTLE SUPPORT,
CRADLE AND PINTLE ASSEMBLY.
WE 12075
Figure 3-14. Removal/Installation - cal. .50 machine gun and spent brass ejection chute.
3-23
TM 9-2350-230-12, C4
Section 3-5. (SUPERSEDED) SMOKE DEVICE SYSTEM

WITH XM176 GRENADE PROJECTOR
3-6. Firing Procedure
The following tables and illustrations provide NOTE. Before operation the crew should be familiarized
XM176projector firing system circuit continuity check with the location and operation of all controls (figs. 3-15
procedure, immediate action in case of failure to fire, and through 3-17).
firing procedure.
TABLE 3-9. CHECKING XM176 GRENADE PROJECTOR ELECTRICAL SYSTEM CONTINUITY

WARNING: Make certain that projector mounts DO NOT contain grenade

projector assemblies.
1 Remove control box MASTER switch safety wire and FIRE switch safety 3-15/A
safety pin.
2 With vehicle master switch turned on, turn on grenade projector control 3-15/A
box MASTER switch. MASTER switch indicator lamp will illuminate.
FIRE switch ready lamp will illuminate after short warm-up.
NOTE. Turn rims of MASTER and FIRE switch indicator lights counter-
clockwise for "bright" illumination. Adjust intensity as required
after system check-out.
3 Through vehicle serial no. 699 remove protective caps from solenoids 3-15/B
3a On vehicles after serial no. 699, open inspection cover and lift
solenoid guard to expose solenoid plunger.
4 Select LEFT SALVO, RIGHT SALVO, SALVO, and individual positions 3-15/A, B
with control box selector knob and actuate FIRE switch at each position.
Visually or physically inspect solenoid action in each position. If not
operating properly, notify organizational maintenance personnel.
NOTE. Approximately four (4) seconds is required between each firing
operation to recharge the system power supply.
5 After checking electrical continuity and solenoid actuation, turn control 3-15/A
box MASTER switch to OFF position and install safety wire. Insert
safety pin through FIRE switch guard.
3-7. Hangfire and Misfire 3-8. Non-Ignited Grenades (Duds)

a. Misfire. A misfire is the failure of a grenade The number and precise location of all grenade duds
projector to fire due to a faulty propellant charge or firing which have failed to function will be recorded and EOD
circuit. A misfire is not dangerous but cannot be personnel notified of their locations.
immediately distinguished from a hangfire. Refer to table
3-10. 3.9. Storage, Shipment, and Handling
Refer to TM 3-250.
b. Hangfire. A temporary failure or delay in the
action of percussion primer, or propellant charge after 3-10. Shipping Container and Stencil Marking
FIRE switch has been actuated. Momentarily this delay Refer to figure 3-16.
cannot be distinguished from a misfire or complete
failure.
3-24
TM 9-2350-230-12, C4
TABLE 3-10. IMMEDIATE ACTION IN CASE OF FAILURE TO FIRE
1 When misfire or hangfire occurs, wait ten (10) seconds and repeat
attempt to fire two additional times.
NOTE. Approximately four (4) seconds is required between each firing
operation to recharge the system power supply.
2 Should projector(s) fail to fire after three attempts, replace safety 3-15/A
pin in FIRE switch guard and turn grenade projector MASTER switch
to OFF position and lock wire.
3 Remain buttoned up in vehicle for 15 minutes (minimum) and advise
ground personnel to remain 100 yards to rear of direction of fire.
4 Release rubber retaining strap and remove projector(s) from mount.
5 Notify EOD Personnel.
TABLE 3-11. LOADING, FIRING, AND UNLOADING XM176 GRENADE PROJECTOR
INSPECTION
1 Check grenade projector electrical system continuity, table 3-9.
2 Remove grenade projectors from shipping containers 3-16/A
WARNING: 1. Exert caution whew handling and loading XM176 grenade
projectors.
2. Under no circumstances attempt to disassemble the
XM176 grenade projectors.
3. Projectors having external cracks, dents or other
deformities must not be used. Notify Explosive
Ordnance Disposal Personnel (EOD).
LOADING GRENADE PROJECTORS INTO MOUNT

THROUGH VEHICLE S/N 699
CAUTION: Make sure FIRE switch safety pin is installed and 3-15/A
box MASTER switch is safety wired.
3 Place projector in mount and engage groove in end of projector with 3-15/C
retaining springs in mount. Solenoid plunger must be in contact
with face of propellant cartridge when projector is properly positioned.
4 Secure projector in mount with rubber retaining strap. Make sure 3-15/C
that crossbar on retainer strap hook is properly engaged in mount.
3-25
TM 9-2350-230-12, C4
TABLE 3-11. LOADING, FIRING, AND UNLOADING XM176 GRENADE PROJECTOR-Continued
LOADING GRENADE PROJECTORS INTO MOUNTS

AFTER VEHICLE S/N 699
CAUTION: Open inspection covers and check tubes for foreign matter
before loading. Close inspection covers.
3a Rotate locking lever ring at top of tube to release locking levers
(figure 3-15. 1) and place grenade projector in tube.
4a Rotate ring to locked position.
FIRING GRENADE PROJECTORS
5 Secure all hatches before firing projectors 2-6, 2-20
6 Keep ground personnel at least 100 yards to rear of direction of fire.
7 Using selector knob, select individual grenade projector, LEFT SALVO, 3-15/A
SALVO, OR RIGHT SALVO firing.
8 Remove safety wire and turn on grenade projector control box MASTER 3-15/A
switch. Green lamp will illuminate.
9 Remove FIRE switch safety pin and double check area for unauthorized 3-15/A
personnel.
10 When red "ready" lamp illuminates, press FIRE switch and fire 3-15/A
projector(s).
NOTE. Approximately four (4) seconds is required between each
firing operation to recharge the system power supply.
WARNING: An installed projector is a loaded weapon and must be 3-15/C
treated as such.
MISFIRE AND/OR HANGFIRE
WARNING: For immediate action in case of a misfire or hangfire,
refer to table 3-10.
UNLOADING UNFIRED GRENADE PROJECTORS
WARNING: When mission is interrupted or completed, all unfired
projectors shall be removed from the mounts. Follow
steps listed below in exact order to properly disarm
and remove projectors.
11 Install safety pin in FIRE switch guard on control box 3-15/A
12 Turn grenade projector MASTER switch to OFF position and safety wire 3-15/A
3-26
TM 9-2350-230-12, C4
TABLE 3-11. LOADING, FIRING, AND UNLOADING XMI76 GRENADE PROJECTOR - CONTINUED
13 Vehicle through serial no. 699: Release retaining straps.

Vehicle serial no. 700 or later: Open locking levers.
14 Remove unfired launchers from tube assemblies and store as live
ammunition.
15 Vehicle through serial no. 699: Install protective caps on solenoids
and stow retaining straps.
15a Vehicles after serial no. 699: Leave spent launchers in tube
assemblies until ready to reload.
3-27
TM 9-2350-230-12, C10,
A. GRENADE LAUNCHER CONTROL BOX 8. GRENADE LAUNCHER MOUNT.

(EARLY VEHICLES ONLY)
C. GRENADE LAUNCHER ASSEMBLIES INSTALLED IN MOUNT (RIGHT SIDE SHOWN,

LEFT SIDE SIMILAR. (EARLY VEHICLES ONLY)
WE 66684
Figure 3-15. Grenade launcher mounts and control box
3-28
TM 9-2350-230-12, C 10
GRENADE LAUNCHER CONTROL BOX TUBE ASSEMBLY LOCKING LEVER RING
GRENADE LAUNCHER TUBE ASSEMBLIES ON TURRET (RIGHT SIDE SHOWN, LEFT SIDE SIMILAR).
WE 70042
Figure 3-15.1. Grenade launcher tube assemblies and control box.
3-29
TM 9-2350-230-12, C10,
Figure 3-16. XM176 grenade launcher shipping container and stencil marketing.
Figure 3-17. XM176 grenade launcher M34 WP estimated casualty zone (flat terrain).
3-30
TM 9-2350-230-12, C3
CHAPTER 4
CREW PREVENTIVE-MAINTENANCE SERVICES
Section 4-1. PREVENTIVE-MAINTENANCE SERVICES
4-1. Specific Procedures (Normal Conditions) The crew should be familiar with quarterly organizational
a. General. This section contains specific preventive-maintenance service requirements, and assist
preventive-maintenance checks and services of materiel in the accomplishment of these services.
to be performed by the crew. Checks and services will
be performed in numerical sequence as indicated in 4-2. Specific Procedures (Unusual Conditions)
table 4-1. Refer to TM 38-750 for instructions on use of a. Vehicles exposed to extreme-cold or hot weather
forms pertaining to preventive-maintenance services. will require more frequent servicing. Materiel subjected
b. Responsibility. Perform all before, during, and to salt-water immersion should be evacuated to
after-operation preventive-maintenance checks and organizational maintenance as soon as possible after
services each day that vehicle is operated, in order to exposure.
detect first signs of failures and to take corrective action b. The letter "C" following the numerical sequence
before extensive repairs are required. While operating number in the interval column indicates services to be
the vehicle, the crew should be alert for any unusual performed when operating under cold weather
noises, odors, abnormal instrument readings, steering environment.
irregularities or any other vehicle malfunction indication.
Figure 4-1. Hull drain holes
Section 4-2. LUBRICATION
4-3. Service Intervals (Normal-Unusual Conditions) operation and extreme conditions, such as high or low
temperatures, prolonged periods of high-rate operation,
a. Service Intervals (Normal Conditions). LO 9- continued operation in sand or dust, or exposure to
2350-230-12 (Appendix IV). moisture, any one of which may quickly destroy the
b. Service Intervals (Unusual Conditions). Reduce protective qualities of the lubricant. Lubrication intervals
lubrication intervals to compensate for abnormal may be extended during inactive periods.
4-1
TM 9-2350-230-12, C12
Table 4-1. PREVENTIVE-MAINTENANCE CHECKS AND SERVICES
INTERVAL AND
SEQUENCE B - BEFORE OPERATION D - DURING OPERATION A - AFTER OPERATION REFERENCE
B D A ITEM TO BE INSPECTED PROCEDURE
74 Vehicle Clean interior and exterior, removing dirt, mud, and excess Table 4-2
grease. Use water hose on vehicle exterior only, avoid
directing stream in areas where it might enter fire
control or armament openings, vehicle interior, engine
exhaust system or personnel heater outlet.
NOTE. Visually inspect for evidence of lubricant and

fuel leaks.
SUSPENSION SYSTEM
1 75 Components Inspect entire suspension system for tampering, excessive Figs. 1-1, 2
wear, damage, or looseness.
64 76 Wheel Hubs and a. Feel wheel hubs cautiously for noticeable variations of Fig. 5-4
Shock Absorbers temperature between like components An overheated hub
indicates a maladjusted, inadequately lubricated, or
damaged bearing. Shock absorbers should feel warmer
than the hull. If cold, shock absorbers are not working.
2 77 b. Check grease in road wheel and idler hubs, or Figs. 9-64

check for lubricant leaks and 9-69
78 Torsion Bars Pry up each road wheel to detect broken torsion bars Fig. 5-4
Broken front torsion bars may be detected by the absence
of the sharp angle of track as it passes under the road
wheel. Check if torsion bar covers are secure.
3 79 Track Check track tension. Adjust if required Fig. 5-4
NOTE. 50 miles after initial break-in or whenever track

pin nuts have been disturbed, retorque track pin retaining
nuts to 120-130 lbs. -ft.
HULL (EXTERIOR)
4 80 Driving Lights Check operation. Inspect for broken or discolored lenses Figs. 2-8 and
Turn on infrared lights and check operation by placing 5-6
hand on lens. Heat will be noticeable if light is operating.
Replace damaged lamps if authorized.
81 Towing Shackles Must be secure Fig. 2-15
82 Personnel Heater, Remove any mud or debris. Clean drain holes with wire or 3, 17, Fig.
Bilge Pump, suitable tool 1-1 and 4,
Exhaust outlets, Fig. 1-2
and Hull Drain Fig. 4-1
Holes
5 Fixed Fire Extinguisher Check condition of fixed fire extinguisher exterior actuating 18, Fig. 1-1
Exterior Control handle. Safety wire must be intact.
4-2
TM 9-2350-230-12, C10
INTERVAL AND
6 83 Exterior Stowage Check condition and secure stowage of basic-is sue items Figs. 1-1
and 1-2
84 Access Plugs Make sure all access plugs are installed and secure on Fig. 5-7
underside of hull.
85 Batteries Check battery electrolyte level; electrolyte level should be up Fig. 5-0
to split ring as indicated on battery filler opening. Inspect D, Fig. 5-3
lugs, terminals and cables for corrosion. Check for loose
battery hold-downs and brackets. If electrolyte level is
repeatedly low or batteries excessively hot and boiling,
notify organizational maintenance personnel.
6.1 64.1 86 Air Cleaner Check air restriction indicator. If indicator is red, clean Fig. 5-1
filter element Fig. 5-0
CAUTION: Do not hold element to exhaust for cleaning as Fig. 4-6

diesel oil film will make it unserviceable. Handle element
carefully to prevent denting or damage .
NOTE. Under severe dust conditions, engine power loss

or excessive black exhaust smoke may indicate need for
more frequent cleaning. During operation in severe dust,
check air restriction indicator frequently.
ENGINE COMPARTMENT
CAUTION: Before starting engine, make sure of

adequate coolant, and adequate oil supply in engine and
transmission.
7 Engine With engine off, check connections and inspect for lubricant A, Fig. 5-2
leaks. Start engine, observe if it develops adequate
cranking speed and starts without excessive noise. Listen
for unusual noises in engine that might indicate improper
operation or lack of lubrication.
8 87 Surge Tank Check coolant level. Add if required to fill m ark on tank A, Fig. 5-2
9 88 Engine Oil Level Check oil level. Add oil as required (LO 9-2350-230-12), A, Fig. 5-2
Indicator
89 Engine Breather Check for visible signs of overflow or spattering of oil B, Fig. 5-3
Drain Collector from box. Drain if such signs are found.
Box
89.1 Coolant Pump Check for proper belt tension Fig. 5-1.1
Drive Belts
9.1 89.2 Coolant Radiator Check cleanliness of radiator fins and tubes. Clean with Fig. 4-6
low pressure air radiator cleaning system.
90 Generator/Fan Check drive belts tensioner. If pin is less than 1/4-inch A, Fig. 5-2
Drive Belts from bracket, notify organizational maintenance personnel,
4-3
TM 9-2350-230-12, C8
INTERVAL AND
10 90.1 Fuel Filters Drain condensation into suitable container C, Fig. 5-2
11C Engine Air Box Check accumulator pressure. If pressure is not maintained Fig. 2-14
(Flame) Heater notify organizational maintenance.
12 91 Transmission Oil Check oil level. Add oil as required (LO 9-2350-230-12), A, Fig. 5-2
Level Indicator
DRIVER’S COMPARTMENT
13 92 Fixed Fire Extinguisher Visually inspect fire extinguisher for evidence of any defect B, Fig. 2-18
in cylinder mounting brackets, control mechanism,
discharge lines, or damaged seals (safety wire).
14C 65C 93C Personnel Heater Check for proper operation. Inspect for fuel and exhaust Fig. 2-17
leaks.
94 Driver’s Hatch Must lock securely in open and closed positions. Check B, Fig. 2-6
Cover latches and seals for damage or deterioration.
95 Driver’s Seat Examine seat for loose nuts and screws and proper A, Fig. 2-6
operation.
96 Ammunition Racks Check for broken latches and hinge pins Fig. 3-3
15 97 Bilge Pumps Check operation and service Fig. 2-13
16 66 98 Switch and lndicator Check panels for proper mounting and loose connections Figs. 2-9
Panels Observe for normal readings and operation of gages, and 2-10
instruments, warning lights, and indicator lights.
Check selector knob setscrews.
17 99 Fuel Gage Check fuel level Fig. 2-9
NOTE. Refill tank immediately after operation to

avoid condensation.
67 Driving Controls Inspect and operate steer, shift, accelerator, and brake Fig. 2-5
controls. Note any binding or excessive play in
linkage. Check brake for ability to hold on steep
grades.
18 M47 and M48 a. Check that all components of the wiper assembly are Fig. 2-7
Periscopes functioning properly.
19 100 b. Check periscope washer fluid reservoir and refill Fig. 2-7
4-4
TM 9-2350-230-12, C8
INTERVAL AND
TURRET (EXTERIOR)
20 101 Exterior Stowage Check condition and stowage of exterior basic-issue items Figs. 1-1, 2
21 Gun-Launcher Tube a. Wipe dry before firing 5, Fig. 1-1
22 102 b. Check for powder fouling, corrosion, and other

damage.
c. Check equipment log book (Form 2408-4) App. I
23 103 Bore Evacuator Check for dents and improper seals. Assure that bore
Chamber evacuator is secure to tube.
104 Deleted
23.1 104.1 Grenade launcher Check wiring harness and connectors. Check operation of Table 3-9
mount (thru veh. solenoids. Notify organizational maintenance Fig. 3-15
SN 699 if defects are found.
23.2 104.2 Grenade launcher On vehicles SN 700 and above, check for bent, dented, Table 3-9
tubes (eff. Veh. corroded or damaged tubes. Check operation of Fig. 3-15.1
SN 700) solenoidsNotify organizational maintenance if defects
are foundClean tubes and leave a light film of oil on
inside of tube. Assure solenoids are left oil-free.
CAL. .50 MACHINE GUN
WARNING: Clear machine gun before initiating inspection .
24 Barrel Assure that bore and chamber are dry and free of
obstruction.
25 Back Plate Assy Assure positive functioning of latch, latch lock, and Fig. 5-14
safety.
26 Cover Group Assure positive engagement of latch B, Fig. 3-8
27 Feed Mechanism Ascertain free movement of latch and feed mechanisms.
105 Retracting Slide Operate slide to assure freedom of movement E, Fig. 3-8
Group Assy.
28 Headspace and Check and/or adjust Tables 3-7, 8

Timing
COMMANDER’S CUPOLA
29 106 Hatch Covers and Check to insure split hatch covers lock securely in all B, Fig. 2-20
Seals positions and have a watertight seal.
107 Vision Blocks Inspect for signs of ineffectual sealing, clouding, 2, Fig. 2-21
objectionable scratches, or pits on surface of glass.
29.1 1071 Slip Ring and Inspect. Clean as necessary with dry cloth.
Brushes
4-5
TM 9-2350-230-12, C6
INTERVAL AND
30 108 Traverse Mechanism Rotate full 360 degrees manually to determine that ring Figs. 2-4,
gear is free and backlash is not excessive. Power 2-21, 2-22
traverse cupola 360 degrees in each direction with Table 2-8
traverse mechanism switch assembly buttons on machine
gun spade grips and rotation switch on cupola control
assembly. Cupola should not coast after release of
buttons or rotation switch.
TURRET (INTERIOR)
NOTE Check selector knob setscrews.
31 109 Loader’s Hatch Check seal and crash pad for damage or deterioration D, Fig. 2-20
Cover Hatch cover must lock securely in open and closed
positions.
32 Turret Seats and Check for ease of operation and adjustment Inspect A, C, F, Fig.
Pads cushions and pads for secure mounting and serviceable 2-20
condition.
33 110 Turret Traverse Check for effective operation C, Fig. 2-20

Lock
34 Ammo Racks and Check pin safety clips securing vertical ammo rack and Fig. 2-27
Protective screens to turret ring to be sure they are installed.
Screens
35 111 Ammo Racks Check ammo arms and catches for shell holding tension Fig. 3-3 and
Determine if shell pads are present and properly 3-3.1
installed.
112 Stowage Boxes Clean miscellaneous boxes of corrosion and debris C, Fig. 2-20
35.167.1 112.1 Floor Access Clean debris from under turret floor as necessary Fig. 4-3
36 Fuel Tank(Center) Drain condensation A, Fig. 5-3
37 113 Interior Basic- Check condition and stowage.

Issue-Items
38 114 Turret Ventilating Fan Check operation E, Fig. 2-20
39 115 Dome Lights Check operation. Replace lamps if defective D, Fig. 2-6
40 116 Turret Traverse With vehicle on level ground, traverse turret full 360 Table 2-7
Mechanism degrees manually and with power. Effort required to
manually traverse should be uniform and must not
have over 1-1/2 mils of backlash. If manual control shaft
binds, coat with PL.
4-6
TM 9-2350-230-12, C11
INTERVAL AND
TURRET (INTERIOR) - Continue
41 117 Elevating Mechanism Elevate and depress through entire range manually and Table 2-7
electricallyCheck operation for smoothness, ease of
operation, and for not more than 1-1/2 mile of backlash.
42 Control Handle Trim Button Adjust for any elevation or azimuth drift Figs. 2-19, 21
41.1 Power Control Clean between heel of palm switch and control handle with Fig. 2-19
Handle the thin bladed tool, as required, to prevent build-up
of dirt.
43 M8A3 Air Filter Check operation of filter unit and listen for unusual noises Table 2-6
Unit Inspect all components for damage, wear, missing
components, and tightness. Inspect air flow control cape
for tightness. Report deficiencies to organizational
maintenance personnel.
44 118Radio Equipment a. Check the completeness and general condition of the Figs. 7-4, 5
equipment.
b. Use a clean lint-free cloth to remove dust, dirt,
moisture, and grease from the antenna, antenna
matching unit, front panel controls of the components
and audio accessories. If necessary, wet the cloth
with cleaning compound 7930-395-9542. Wipe the
parts with a clean dry cloth.
WARNING: Cleaning compound (Federal Stock No.

7930-395-9542) lt flammable and its fumes are toxic.
Do not use near a flame; provide adequate ventilation.
c. Check to see that all controls work smoothly, are tight
on the shaft, and do not bind.
d. Check for normal operation.
e. Inspect cords and cables for cuts, kinks, breaks,
fraying, and undue strain.
f. Inspect for loose connectors.
g. Clean dial windows with a clean, dry cloth.
h. Replace lamps if defective.
152MM GUN-LAUNCHER
WARNING: Clear weapon before starting inspection.
44.1 67.2 118.1 Detent Assembly Notify Organizational Maintenance to service:
and Check Valve a. Check valve after each 100 rounds
b. Type I or n detent assembly For detent
(1) After each day’s firing - not to exceed assembly
40 rounds between cleaning identification
(2) Upon completion of firing when no more refer to
firing is anticipated(Detent will be cleaned para 3-3, 4
three consecutive days in conjunction with
cannon tube per L09-2350-230-12. )
(3) Every 90 days when not firing
4-7
TM 9-2350-230-12, C9
INTERVAL AND

152MM GUN-LAUNCHER
WARNING: Clear weapon before starting inspection.
44.1 67.2 118.1 Detent Assembly Notify Organizational Maintenance to service detent
and Check Valve each 40 rounds and check valve each 100 rounds.
45 119 Electrical Lead Check for positive connection E, Fig. 3-1
119.1 Gun-Launcher After firing, gun-launcher tube must be cleaned daily Table 5-8. 1
Tube (M81 tubes must also have bore evacuator valves
and chamber cleaned daily).
46 68 120 Breech Mechanism a. Open and close breech both manually and electrically to E, Fig. 3-1
Assembly assure smoothness of operation and that no binding
exists. Check the fully closed position for alignment
of scribe marks on breech chamber with index mark
on coupling.
b. On the opening cycle, check operation of missile cap D, E, Fig.
ejector when ejector trigger lever is in the eject (down) 3-1
position. Just prior to ejection, check missile case
detent in gun tube chamber to insure it is completely
withdrawn. At full open breech position, the detent
should protrude into chamber.
46.1 68.1 120 CO2 Bore Scavenging After each 10 rounds, check CO2 bottle weight Fig. 3-2.1
System and 3-2. 2
47 121 Obturator Seal Check to insure seal is not damaged and is in proper Fig. 5-101
position in gun tubeClean as specified in Table 5-8. 1 Table5-8.1
CAUTION: When firing conventional ammo clean
firing probe every 5-10 rounds.
47.1 68.2 Firing Probe Clean probe with rough cloth or steel wool (FSN 5350-
242-4404). Check firing probe continuity Fig. 4-4
NOTE. Every 200 conventional rounds interval, notify

organizational maintenance to remove, clean, and inspect
probe and seal seat on breechblock face.
CLOSED BREECH SCAVENGING SYSTEM
47.2 CBS Pressure Gage a. Check pressure gageIf pressure is below 2700 PSI Fig. 3-9 3
and System start vehicle engine and operate compressor to charge
Operation system to 3100 + 100 PSI.
CAUTION: Avoid damage to air cylinders, which are
under very high pressure.
b. Momentarily actuate manual discharge lever to check Fig. 3-2.4
operation of system.
121.1 Compressor a. Inspect compressed air lines, oil lines and mounting
hardware for loose connections or leakage. Notify
organizational maintenance to correct defects.
b. Clean finned tubes and fan screen as required.
c. Inspect cooling tubes for distortion, cracks, dents and
loose connections. Inspect fan for dents, bent blades,
looseness or other defects. Notify organizational
maintenance to correct defects.
4-8
TM 9-2350-230-12, C10
INTERVAL AND
CLOSED BREECH SCAVENGING SYSTEM - Continued
d. Remove any object obstructing moving parts.
e. After each day of operation check oil level Clean area Fig. 3-2.4
around filler hole. Add oil to full mark. Under extreme
operating conditions, such as excessively high or low
temperatures, prolonged operating periods, operation in
sand or dust, or immersion in water, notify organizational
maintenance for additional service.
68.3 Compressor Monitor compressor for: unusual noises, vibration,

smoking, or overheating. If cause of abnormal operation
cannot be located and corrected, shut down compressor
and notify organizational maintenance.
121.2 Compressor Visually Inspect compressor for obvious signs of damage,

oil leaks, looseness or wear. Notify organizational
maintenance to correct defects.
47.3 121.3 CBS Hoses Check CBS hoses for air blisters under outer cover Fig. 4-5
Bleed air from blisters larger than dime-size.
MOUNT
48 69 122 Mount Elevate and depress weapon throughout entire range,

observing performance.
49 70 123 Recoil Mechanism a. Check for leakageNotify organizational maintenance Fig. 3-2
if leak is evident.
71 b. Check for smooth operation and complete return to

battery without undue shock.
72 124 Counter-recoil Buffer a. Check for leakage Fig. 5-9
50 b. Check oil level (Mounts without buffer bleed line only). Fig. 5-9
51 Mount Reservoir Check fittings for loose connections Check hydraulic fluid level. Fig. 3-2
52 73 Safe-to-Fire Mechanism Check to insure that indicator rod is within operating range Fig. 3-2
7.62MM MACHINE GUN,
WARNING: Clear weapon before initiating inspection .
53 Feed components, Use dummy cartridges to assure positive functioning Figs. 3-5
safety and Assure that electrical connectors are intact and and 3-7
manual trigger solenoid functions properly.
125 Components and Replace defective parts authorized or notify organizational

Assemblies maintenance.
54 Barrel Assembly Assure bore is dry and free of obstructions.
4-8.1
TM 9-2350-230-12, C9
INTERVAL AND
55 126 Coaxial Machine Ascertain components are not damaged or missing.

Gun
SIGHTING AND FIRE CONTROL
56 M13AlC Quadrant a. Inspect for general condition and completeness. Note Fig. 2-28
legibility of scales and indices; clean as required. Check
that level vial rotating cover is in a protected position
when quadrant is not in use.
b. Check for tightness of screws, binding, legibility of Fig. 2-28

scales, condition of level vial and cover. Check
adjustment.
57 Azimuth Indicator a. Inspect for general condition and completeness. Replace Table 5-6
lamp if defective.
b. Check for slippage and/or accuracy Fig. 2-27
58 M119 or M127 a. Inspect general condition and completeness. Check Fig. 2-25
Telescope and that locking lever Is in detent position. Inspect Table 5-6
M149 Telescope headrest . Check operation of diopter adjustment and
Mount scale, filter selector lever bore sight knobs, slip
scales, and locking lever. Inspect lens and windows
for dirt, chips, cracks, and fungus growth. Check
electrical connections. Replace lamp if defective.
b. Check for parallax and adjust to eliminate if found Table 2-9
c. M127 telescope only: Check that dual power selector

lever is operable and seats firmly against stops.
59 XM44 Series Peris- Inspect general condition and completeness. Check Fig. 2-26
cope and operation of knobs and levers. Inspect lens and and Table
Control Panelwindows for dirt, cracks, and chips. Check 5-6
electrical connections. Replace lamps if defective. Check
periscope washer fluid reservoir and refill.
60 Night Vision a. Inspect all components for dirt, loose, damaged,

Sight or worn parts. Focus knobs must operate freely.
Objective lens focus knob locking device must have
positive locking action. Check eyepiece focus ring
for free operation and focusing. If defective, notify
b. In darkened area, turn rotary control switch clockwise Fig. 2-29

to reticle (second click-stop) position and check for and Table
reticle illumination. Continue to rotate rotary control 5-6
switch clockwise through remaining three reticle lamp
positions and check for increasing brightness at each
position. If weak or no illumination, replace battery and/or
reticle lamp. If no light variation, report condition
to organizational maintenance personnel.
4-8.2
TM 9-2350-230-12, C6
BLEEDING MOISTURE FROM AIR CYLINDERS

1. FOLLOW STEPS 1 THROUGH 4 BELOW FOR
BLEEDING AIR PRESSURE FROM SYSTEM.
2. LOOSEN BLEED SCREWS ON TOP OF EACH
CYLINDER MANIFOLD TO BLEED MOISTURE
FROM CYLINDERS.
CAUTION: DO NOT REMOVE OR LOOSEN

BLEED SCREW GUARD.
BLEEDING AIR PRESSURE FROM SYSTEM
1. TURN COMPRESSOR SWITCH OFF (FIG. 3-

2.3).
2. MANUAL SHUT-OFF VALVE IS TO BE IN
OPEN POSITION (FIG. 3-2.4).
3. MAKE SURE GUN-LAUNCHER BREECH IS
CLOSED.
4. DEPLETE AIR SUPPLY BY USING MANUAL
LEVER ON THE SOLENOID DISCHARGE
VALVE (FIG. 3-234) UNTIL PRESSURE IS
REDUCED TO 500 PSI.
5. CONTINUE TO CYCLE MANUAL DISCHARGE
LEVER UNTIL PRESSURE IS COMPLETELY
Figure 4-2. Bleeding closed breech scavenger system. DEPLETED.
LEGEND
1. SCREW (2)
2. WASHER (2)
3. ACCESS COVER
USE 9/16" SOCKET TO REMOVE 2

SCREWS. REMOVE 2 WASHERS
AND ACCESS COVER TO PROVIDE
ACCESS TO HULL FLOOR UNDER
TURRET. TRAVERSE TURRET
MANUALLY AND REMOVE SPENT
BRASS AND OTHER DEBRIS FROM
HULL FLOOR. REINSTALL ACCESS
COVER AND TIGHTEN SCREWS
SECURELY.
Figure 4-3. Turret floor access cover.
4-10
TM 9-2350-230-12, C8
TABLE 4-2. CLEANING CREW COMPARTMENT
STEP PROCEDURE
1 During cold weather, operate vehicle engine and personnel heater as required to
thaw frozen liquids.
2 Remove loose debris from driver’s compartment. Remove turret floor access cover
if present and remove debris from hull under turret floor (Fig. 4-3).
3 Scrub floor and other dirty areas with detergent and a minimum of water.
CAUTION: 1. Do not use water hose or steam in vehicle interior.

2. Protect all electrical items against wetness (water or solvent).
4 Front bilge pump is normally used to remove liquids from the cleaning operation.
However, if front bilge pump is inoperative or inadequate, rear bilge pumps and/or
hull access plugs may be used by following steps 5 through 7.
5 Assure that engine bulkhead drain holes are open.
6 Elevate front of vehicle slightly (6 to 10 inches) by driving up an incline or onto

timbers or refuse.
7 Operate rear bilge pumps or remove one or more hull access plugs (Fig. 5-7) to
evacuate liquids from engine compartment.
CAUTION: Follow instructions in Figure 5-7 when installing access plugs.

NOTE. Make sure turret area under compressor is kept clean. Mud or debris
in this area can cause compressor motor to short out, resulting in malfunction or
damage.
Figure 4-4. Checking firing probe continuity
4-11
TM 9-2350-230-12, C9
Figure 4-5. Deflating blisters on CBS hose.
Figure 4-6. Operation of low pressure air radiator cleaning kit
4-12
TM 9-2350-230-12, C9
Figure 4-7. Operation of engine bulkhead access panels
4-13/(4-14 Blank)
TM 9-2350-230-12
CHAPTER 5
CREW MAINTENANCE
Section 5-1. REPAIR PARTS, TOOLS, AND EQUIPMENT
5-1. Repair Parts, Tools, and Equipment

Refer to Appendix II
Section 5-2. TROUBLESHOOTING
5-2. scope
The following table contains crew troubleshooting of
materiel in case of malfunction and the corrective action
to be taken.
Table 5-1. Troubleshooting
Malfunction Probable causes Corrective action

NOTE. For corrective action of
malfunctions not listed in this table,
refer to organizational maintenance
personnel.
ENGINE
1. Fails to crank, or cranks slow- a. Vehicle MASTER SWITCH not on a. Turn vehicle MASTER SWITCH on
ly, when starter is actuated (Fig. 2-10)
b. Batteries discharged b. Use an external power to start engine
(Table 2-5).
c. Transmission shift lever not in N c. Move to N (neutral) position (F, Fig.
(neutral) position 2-6).
d. Loose or corroded battery cable d. Clean and tighten (0, Fig. 5-3).
terminals.
e. Incorrect oil viscosity for prevailing e. Drain (Fig. 5-7) and refill (A, Fig.
ambient temperatures 5-2) as specified in LO 9-2350-230-
12.
f. Internal engine seizure f. If engine cannot be rotated one complete
revolution, notify organizational
2. Engine cranks but fails to start a. Restricted fuel tubes or hoses a. Check for plugged, kinked, or pinched
fuel tubes or hoses.
b. Fuel tanks empty b. Check fuel tank gage (Fig.2-9).
c. Main fuel hose disconnected c. Connect fuel hose (C, Fig. 5-2).
d. Fuel tank shut-off valves closed d. Open one or both (A, Fig. 5-3).
e. Fuel shut-off control knob pulled out e. Push in fuel shut-off control knob.
3. Does not maintain constant a. Insufficient fuel a. Check fuel lines and filters (Fig. 5-2)
speed b. Water in fuel b. Drain condensation from fuel filters
(C, Fig. 5-2) and fuel tanks (A,
Fig. 5-3).
4. Accelerating improperly a. Improper fuel a. Drain fuel tanks (Table 5-4) and refill
(C, Fig. 5-3) with correct fuel
(Par. 1-6).
b. Insufficient fuel b. Check fuel lines and filters(Fig. 5-2)
for leaks.
c. Insufficient air c. Check air cleaner restriction indicator
(Fig. 5-1).
5-1
TM 9-2350-230-12, C4
Table 5-1. Troubleshooting-Continued

ENGINE - Continued
5. Engine overheats a. Restricted air passages a. Check grilles (5,6, Fig. 1-2) and radiator
for clogging.
b. Cooling fan not operating properly b. Check fan operation (Item 2, Fig. 2-9).
c. Drive belts slipping c. Check tensioner (A. Fig. 5-2).
d. Low coolant level d. Check for leaks and surge tank coolant
level (A, Fig. 5-2).
e. Malfunction of lubrication system e. Check 4U level (A, Fig. 5-) and fill
as specified In LO 9-2350-230-12.
f. Coolant pump inoperative f. Check belt tensioner (Fig .5-1.1
6. Low or no oil pressure a. Low oil level a. Replenish (A, 1*. 5-2).
b. Improper lubricating oil b. Drain (Fig. 5-7) and refill as specified
in LO 9-2350-230-2-1-
c. 0il leaks c. Examine engine compartment Fl.’5-2,
for evidence of oil leaks.
TRANSMISSION
7. Transmission does not drive in Low main oil pressure Chock oil level (A, Fig. 5-2) and
any range replenish (LO 9-2350-230-12).
BATTERIES AND
GENERATING SYSTEM
8. No current in battery circuit a. Loose cable connections a. inspect, clean, and tighten cables and
connection at battery O), Fig. 5-3)
and master relay.
b. Dead batteries b. Replace or charge batteries.
c. Discharged batteries c. Check batteries (D, Fig. 5-3).
9. Batteries do not stay charged Excessive use of electrical equipment Discourage prolonged usage of electrical
when engine is not running equipment without engine running
10. Vehicle MASTER SWITCH indi- a. MASTER 8W1TCH not on a. Turn MASTER SWITCH on (Fig. 2-10).
enter lamp does not light.
b. Lamp burned out b. Replace (Table 5-3).
c. Loose electrical leads c. Inspect and tighten connection if required
TRACKS AND SUSPENSION

11. Vehicle pulls to o de d with a. Improper track tension at Adjust (Fig. 5-4).
Steer bar in center position.
b. Build-op of mud or dirt on one track b. Clean.
12. Vehicle thrown track a Improper driving or operation of a. Improper driving methods. Do not
vehicle make high speed turns.
b. Excessively loose or worn track b. Adjust track tension (Fig. 5-4).
PERSONNEL HEATER
13. Heater fails to 8ta Incorrect operating procedure Refer to operating procedure (Fig. 2-17 .
14. Heat exchanger load up with a. Too heavy grade of fuel oil for ambient a. Improper grade of fuel oil
soot and carbon condition (LO 9-2350-2330-12).
b. Restriction in exhaust b. Remove restriction (4, Fig. 1-2).
5-2
TM 9-2350-230-12. C11

BILGE PUMP
15 Bilge pump does not operate a. Vehicle MASTER SWITCH off a. Turn MASTER SWITCH on (fig 2-10).
with bilge pump switch b Loose electrical leads at circuit b. Inspect and tighten connectors if requited.
turned on breaker, relay, or switch panel
152tM GUN-LAUNCHER
16 Failure to fire conventional Defective ammunition or electrical Refer to immediate action in case of
ammunition or missile malfunction failure to fire (table 3-1).
(READY lamps on ).
17 Failure of loader’s control a. READY lamp defective a. Press to test lamp and replace if in-
box or reticle dimmer box inoperative (fig 2-25 and A, fig 3-1).
READY lamps to illuminate b. Recoil mechanism pressure too b. Adjust pressure (fig 3-2).
high or too low.
c. Gun out of battery c. Check safe-to-fire indicator rod
(fig 3-2) Increase pressure if
required.
17.1 Smoke and fumes discharging Erosion past firing probe Notify organizational maintenance.
from cover of breech.
17.2. Smoke and/or flame discharging Malfunctioning seal; erosion or corrosion Notify supporting maintenance.
from tube lock key or detent of detent assembly or cannon
assembly vent detent hole.
152MM GUN-LAUNCHER MOUNT
18. Breech chamber will not rotate a. Obstruction or foreign material a. Manually open breech and remove
into fully closed position between buttress threads or between obstruction or foreign material.
chamber and tube face.
b. Foreign material inside of breech b. Manually open breech and clean Interior
chamber of breech chamber. Check
operation of scavenging system.
19. Replenisher hand pump does Insufficient fluid in reservoir Replenish reservoir (Fig. 3-2) and
not increase recoil check for excessive recoil oil leakage.
mechanism pressure
30. Gun-Launcher returns to Insufficient fluid in counter-recoil buffer. Add fluid (Fig. 5-9).
battery with excessive force
GUN-LAUNCHER ELEVATING AND
TURRET TRAVERSING SYSTEMS
21. Excessive effort required to a. Excessive load due to binding or a. Remove obstruction.
manually elevate or depress obstruction in shield area or gear
box.
b. Contaminated lubricant on elevating b. Clean and lubricate (LO 9-2350-230-12).
mechanism pivots.
22. Elevating system electric a. Vehicle MASTER SWITCH not on Turn MASTER 8WITCH on(Fig. 2-10).
drive inoperative with palm
switch depressed b. TURRET CONTROL POWER switch b. Turn POWER switch on (Fig. 2-19).
not on.
c. Loose electrical connectors c. Tighten electrical connectors.
23. Creeps excessively, after war Elevation and/or azimuth trim buttons Adjust gunner’s and/or commander’s
up, in elevation, depression, out of adjustment trim button (Figs. 2-19, 21).
and azimuth with control
handles In neutral position.
24. Excessive "dead" space in a. Excessive load, due to binding or a. Remove obstruction.
either control handle when obstruction in shield area.
elevating or depressing.
b. Contaminated lubricant on elevating b. Clean and lubricate (LO9-2350-230-12)
mechanism pivots.
24. 1. Palm switch energized with- Dirt collected under heel of palm Depress palm switch and remove dirt
out being depressed switch with thin bladed tool
5-3
TM 9-2350-230-12, C6

GUN-LAUNCHER ELEVATING AND
TURRET TRAVERSING SYSTEMS -
Continued
25. Traversing system electric a. Vehicle MASTER SWITCH not on a. Turn MASTER SWITCH on (Fig. 2-10).
drive inoperative with palm
switch depressed.
b. TURRET CONTROL POWER switch b. Turn POWER switch on (Fig. 2-19).
not on.
c. Loose electrical connectors c. Tighten electrical connectors.
26. Turret will not power traverse Turret traverse lock engaged Disengage (C, Fig. 2-20).
in either direction.
27. Traverse or elevation servo Excessive load, due to obstructions or Remove obstructions.
motors overheat during foreign matter in turret ring gear.
operation.
28. Motor-Generator does a. Vehicle MASTER SWITCH not on a. Turn MASTER SWITCH on (Fig. 2-10).
not operate with control
handle palm switches de- b. TURRET CONTROL POWER switch b. Turn POWER switch on (Fig. 2-19).
pressed not on.
c. Loose wiring harness connections at c. Tighten connections (F, Fig. 2-20).
motor-generator.
POWER ASSIST CUPOLA
29. Cupola sluggish in electrical Excessive foreign matter in bearing or Clean (B, Fig. 2-20).
power position ring gear.
30. Power rotation in one direction Loose connections at control assembly Check (3, Fig. 2-21).
only with or without pushing
direction switch.
31. No rotation a. No electrical power a. Turn cupola control assembly POWER
switch to ON position (3, Fig. 2-21) .
CAUTION: If humming noise
is heard from motor with b. Foreign matter in slip ring b. Remove matter and clean.
POWER switch in ON position
turn to OFF position, and c. Loose connections at control assembly c. Check (3, Fig. 2-21).
notify organizational maintenance. (Table 5-9).
7.62MM MACHINE GUN
32. Failure to feed a. Defective link or ammunition a. Remove faulty link and/or round.
b. Defective driving stud, b. Replace barrel extension assembly.
c. Cover unlatched c. Close cover.
d. Feed system improperly loaded d. Open door on ammunition feed box
(A, Fig. 3-5) and make sure link
belt is properly looped and is not
kinked.
e. Gun improperly loaded e. Load according to Table 3-5.
33. Failure to chamber a. Defective ammunition.(Short-round) a. Replace faulty round.
b. Ammunition belt installed upside down. b. Install belt properly.
c. Defective driving springs c. Replace springs.
d. Defective cartridge rammer d. Replace barrel extension assembly.
e. Obstruction by foreign substances or e. Remove obstructing matter.
material in chamber.
f. Defective rammer actuator roller f. Replace barrel extension assembly.
5-4
TM 9-2350-230-12
Table 5-1. Troubleshooting-Continued 6,
7.62MM MACHINE GUN

Continued
34. Failure to lock a. Breechblock assembly incorrectly a. Install properly.

installed.
b. Defective breechblock roller and/or b. Replace breechblock assembly.
shaft.
c. Barrel Installed incorrectly. Not c. Install barrel properly.
engaged in barrel extension or
upside down.
d. Defective lever actuator (breech - d. Replace barrel extension assembly.
closing) roller.
35. Failure to fire a. Fire control selector not in CQAX a. Turn to COAX position (Fig. 2-19).
position.
b. Defective barrel extension assembly b. Replace.
c. Defective firing pin c. Replace breechblock assembly.
d Defective firing pin extension Replace barrel extension assembly.
e. Loose connector e. Inspect electrical harness.
f. Safety in ('S” position f. Slide safety to ("F'' position.
g. Defective ammunition g. Remove faulty round.
36. Failure to unlock Defective lever actuator (breech - Replace barrel extension assembly.
opening) roller.
37. Failure to extract a. Defective cartridge case (rim ruptured) a. Remove spent case (Fig. 3-6).
b. Defective extractor b. Replace barrel extension assembly.
c. Defective cartridge rammer c. Replace barrel extension assembly.
d. Defective extractor spring d. Replace barrel extension assembly.
e. Pitted chamber e. Replace barrel assembly.
f. Short recoil f. Investigate for binding parts, clean
and lubricate (LO 9-2350-230-12).
38. Failure to eject Defective barrel extension assembly Replace.
39. Failure to cock Defective barrel extension assembly Replace.
40. Uncontrolled automatic fire a. Defective barrel extension (sear a. Replace.
notches).
b. Defective receiver tabs b. Notify organizational maintenance.
41. Improper rate control Missing rate control pawl Replace barrel extension assembly.
42. Failure to load a. Ammunition placed in feedway a. Reposition ammunition belt.
incorrectly.
b. Link from previous belt in feedway b Remove expended (last) link.
CAL. .50 MACHINE GUN, M2 (Table 5-10)
43. Failure to feed Defective ammunition belt Remove damaged link or reposition
rounds.
44. Failure to chamber Damaged round, obstruction in T-slot, Remove round and clean T-slot.
or ruptured case.
45. Failure to lock a. Broken or damaged parts a. Examine for broken parts, battered
breech lock or rough breech lock
cam.
5-5
C6, TM 9-2350-230-12
Malfunction Probable cause Corrective action

CAL 5O MACHINE GUN,M2
(Table 5-10) Continued
45.Failure to lock - Continued b. Insufficient headspace b. Adjust (Table 3-7).

46.Failure to fire a. Defective ammunition a. Remove and insert new ammunition.
b. Incorrect timing b. Adjust (Table 3-8).
47.Failure to extract a. Dirty chamber a. Clean.
b. Broken extractor b. Replace bolt assembly.
48.Failure to cock a. Broken sear a. Replace bolt assembly.
b. Worn sear notch b. Replace bolt assembly.
c. Weak sear spring c. Replace bolt assembly.
d. Worn hooked notch on firing pin d. Replace bolt assembly.
extension.
49.Failure to eject a. Defective ejector a. Replace bolt assembly.
b. Obstructed T-slot in bolt assembly b. Remove obstruction.
M37, M47 AND M48 PERISCOPES
50. Poor visibility a. Dirty optical surface a. Clean optical surfaces with lens
tissues (A, Fig. 5-8).
b. Condensation (M47 and M48 only) b. Refer to TM 750-116
M48 PERISCOPE
51.Foggy or no infrared vision a. Periscope power switch not on a. Check power switch on periscope
(A, Fig. 5-8).
b. Weak or dead cell if operating from b. Replace 1-1/2 volt cell (A, Fig. 5-8)
battery.
NOTE. Place the positive tip of
the cell In housing first.
c. No infrared illumination c. Check target area with another IR
viewing instrument .
52. No fluid from periscope washer a. No fluid in reservoir a. Refill reservoir (Fig. 2-7).
assembly b. Clogged tubing b. Clean tubing or nozzle.
53. Periscope loose after installa- Loose mount assembly Tighten mount assembly bolts (2-12).
tion.
54.Flickering infrared image a. Loose or poor connection a. Check electrical connection (Fig. 2-7).
b. Flickering infrared illumination b. Report condition to organizational
XM44 SERIES PERISCOPE
55.Loss of boresight Boresight knobs not fully engaged Check knobs to insure firm engagement
with clutch teeth (Fig. 2-26).
56.Poor or no reticle illumination a. Periscope power supply ON, OFF a. Turn power supply switch to ON
switch in OFF position position (17, Fig. 2-26).
b. Defective lamp) b. Replace lamp (Table 5-6).
c. Loose or broken connection c. Check all connections on control panel.
5-6
C 10, TM 9-2350-230-12
XM44 SERIES PERISCOPE - Continued
56.Poor or no reticle illumination - d. RETICLE LOGHT intensity control d. Rotate RETICLE LIGHT rheostat knob
Continued rheostat knob on control panel is in (4, Fig. 2-26).
OFF position.
57.Daylight vision foggy a. Dirt or fingerprints on optical a. Clean with lens tissue.
elements.
b. Condensation b. XM44: Refer to TM 750-116.
XM44E Series: Notify Organizational
Maintenance.
58.Foggy image in focal plane at a. Dirt or fingerprints on optical ele- a. Clean with lens tissue.
screen end of image intensi- ments.
fier tube b. Improper focus b. Make initial adjustment of image at
image intensifier tube by turning
diopter knob. Make final focal
adjustment by turning focus knob.
c. Insufficient light in field of view c. Resight periscope and/or main gun to
obtain more light in field of view.
d. Filter aperture not suitable for proper d. Adjust filter lever to proper catch on
illumination of image adapter (21, Fig. 2-26).
58. 1 Inability to focus Image intensifier tube with related Notify organizational maintenance.
parts improperly assembled and/
or installed.
59.Control panel indicator light Defective lamp Replace lamp (Table 5-6).
does not illuminate.
60.No image a. Vehicle MASTER SWITCH turned off a. Turn MASTER SWITCH on (Fig. 2-10).
b. Periscope ON/OFF switch in OFF b. Turn to ON position (17, Fig. 2-26).
position.
61.Excesslve illumination In Wrong filter aperture Adjust filter lever to obtain proper
image filter aperture (21, Fig. 2-26).
M119 OR M127 TELESCOPE
62.Poor definition of field of view a. Eyepiece not focused correctly for a. Rotate diopter knob until Image is
(image not sharp and clear) operator sharp and clear (2, Fig. 2-25).
b. Dirty external optics b. Clean external optics.
c. Condensation c. Refer to TM 750-116.
63.Poor or no reticle illumination a. Improperly adjusted reticle light a. Adjust reticle light rheostat
control (1, Fig. 2-25).
b. Defective lamps b. Replace lamps (Table 5-6).
c. Lack of electrical power to telescope c. Check plugs and receptacle from
instrument to reticle dimmer box
and power source for proper mating.
64.No checksight light beam Burned out or defective lamp Replace checksight lamp (Table 5-6).
AZIMUTH INDICATOR
65.Scales not illuminated a. Lack of electrical power a. Check electrical connections
(Fig. 2-27).
b. Defective lamp b. Replace lamp (Table 5-6).
5-7
TM9-2350-230-12

M13AIC OUADRANT
66. Zero graduations on elevation a. Loose elevation knob a. Level gun with M1A1 quadrant and
scale and micrometer scale align MI3AIC quadrant micrometer
do not coincide (Fig. 2-28), and tighten screws.
b. Loose elevation scale mounting screws. b. Align scale (Fig. 2-28) and tighten
screws.
67. With level bubble centered, Scales improperly adjusted Adjust scales (Fig. 2-28).
elevation scale and microm-
eter scale readings are not
zero.
MISSILE SUBSYSTEM TEST CHECKOUT
PANEL
68. All lamps do not illuminate Defective lamps Replace lamps (Table 5-6).
when LAMP AND METER
TEST switch is held.
69. SIG DATA CONV lamp glows a. ALIGN and ERROR levers in wrong a. Place levers in correct position and/or
at end of self-test position or tracker not aligned perform tracker alignment
(Table 2-12).
b. Checksight lamp defective b. When performing tracker alignment

make certain checksight light is
visible. Replace lamp if necessary
and repeat subsystem checkout
procedures (Tables 2-12 and 5-6).
70. POWER SUPPLY lamp glows Low power from vehicle If vehicle engine is off, start engine,
at end of self-test set idle speed to 750-rpm and
repeat subsystem checkout
procedures (Table 2-12).
71. TRACKER lamp glows at end of Tracker not properly aligned Perform tracker alignment procedure
self-test (Table 2-12). Repeat subsystem
checkout procedure.
NIGHT VISION SIGHT
72. No illumination of reticle a. Weak or dead battery a. Replace battery (B, Fig. 5-8).
b. Defective reticle lamp b. Replace lamp (Table 5-6).
73. Weak or no illumination of a. Objective lens or eyepiece lens dirty a. Clean lenses.
image intensifier tube or or fogged.
image blurred.
b. Objective lens out of focus b. Adjust lens focus (Table 2-11).
c. Eyepiece out of focus c. Adjust eyepiece focus (Table 2-11).
d. Dead or weak battery d. Replace battery (B, Fig. 5-8).
5-8
C8, TM 9-2350-230-12
Section 5-3. MAINTENANCE OF HULL
5-3. Crew Maintenance Instructions
The following tables and illustrations provide hull maintenance instructions to be performed by the crew.
TABLE 5-2. CREW MAINTENANCE - HULL
ITEM INSPECT SERVICE ADJUST INSTALL REPLACE

Engine Air Cleaner and Restric-
tion Indicator Fig. 5-1 Fig. 5-1
Generator "V" Belt Tensioner A, Fig. 5-2
Coolant Pump Belt Tensioner Fig. 5-1.1
Fuel System:
Fill C, Fig. 5-3
Drain Table 5-4
Center Fuel Tank A, Fig. 5-3
Engine Lubricant:
Fill (LO 9-2350-230-12) A, Fig. 5-2
Drain 3, Fig. 5-7
Transmission Lubricant:
Fill (LO 9-2350-230-12) A, Fig. 5-2
Drain 5, Fig. 5-7
Coolant System:
Fill A, Fig. 5-2
Drain Table 5-4
Battery D, Fig. 5-3
Lamps Table 5-3
Engine Fuel Filters C, Fig. 5-2
Track Fig. 5-4 Fig. 5-5
Engine Breather Drain Collector
Box B, Fig. 5-3
Driver’s Periscope Washer
Liquid Reservoir Fig. 2-7
Accumulator Fig. 2-14
Bilge Pump Fig. 2-13
NOTE. For General Cleaning Procedure, refer to TM 9-208-1 and TM 9-247.
5-9
C9, TM 9-2350-230-12
TO SERVICE AIR CLEANER, PULL LOCKING TO SERVICE BATTERY, PULL LOCKING PIN
PIN AND OPEN HINGED DOOR. AND OPEN HINGED SECTION OF DOOR.
NOTE. RESTRICTION INDICATOR (FIG. 5-1) TO REMOVE BATTERIES NOTIFY ORGANIZATIONAL

CAN ALSO BE CHECKED BY OPENING ENGINE MAINTENANCE.
LEFT EXHAUST GRILLE.
CLOSE DOOR AND INSTALL LOCKING PIN
CLOSE DOOR AND INSTALL LOCKING PIN AFTER SERVICING.
AFTER SERVICING.
WE 66598
Figure 5-0. Battery and air cleaner cover and access doors
5-10
C9, TM 9-2350-230-12
Figure 5-1. Servicing engine air cleaner
5-10.1
C4, TM 9-2350-230-12
CHECK BELTS FOR BREAKS AND FOR EXCESSIVE

WEAR.
CHECK BELT TENSION. PROPERLY ADJUSTED

BELTS CAN BE DEPRESSED APPROXIMATELY 1/4
INCH BY APPLYING 5 TO 10 POUNDS PRESSURE AT
POINT "A".
IF BELTS ARE BROKEN OR EXCESSIVELY WORN,

OR ARE IN NEED OF ADJUSTMENT, NOTIFY
ORGANIZATIONAL MAINTENANCE.
WE 119501
Figure 5-1.1. Checking coolant pump belts
5-10.2
C8, TM 9-2350-230-12
A. ENGINE COMPARTMENT
Figure 5-2. Engine compartment, fan drive manual lockup device, and engine fuel filters
5-11
C4, TM 9-2350-230-12
C. ADDING FUEL.
WE 108948
Figure 5-3. Fuel filler cap, batteries, center fuel tank drain pump, and engine breather drain collector box
5-12
C8, TM 9-2350-230-12
CHECKING TRACK TENSION
SAG IN TRACK BETWEEN IDLER AND SPROCKET

MUST BE KEPT BETWEEN 3-1/2 AND 4 INCHES.
CHECK TRACK TENSION BEFORE AND AFTER
VEHICLE OPERATION AS FOLLOWS:
1. PLACE CANTEEN DRINKING CUP FLAT (3-1/2"
DIMENSION) ON TRACK DIRECTLY OVER NO. 3
ROADWHEEL.
2. LIFT FRONT MUD GUARD AND SIGHT FROM
POINT A (TOP OF TRACK ON IDLER) TO POINT B
(TOP OF TRACK ON SPROCKET).
a. IF TOP OF CANTEEN CUP COINCIDES WITH
LINE OF SIGHT, TRACK ADJUSTMENT IS
CORRECT.
b. IF TOP OF CANTEEN CUP OBSCURES LINE
OF SIGHT, TRACK IS TOO TIGHT.
DECREASE TRACK TENSION AS REQUIRED.
c. IF TOP OF CANTEEN CUP IS BELOW LINE OF
SIGHT, TRACK MAY BE TOO LOOSE. CHECK
BY FOLLOWING STEP 3.
3. PLACE CANTEEN CUP UPRIGHT (4" DIMENSION) B. ADJUSTING TRACK TENSION
ON TRACK DIRECTLY OVER NO. 3 ROADWHEEL.
a. IF CANTEEN CUP OBSCURES LINE OF NOTE: IF TRACK SAG CANNOT BE TAKEN UP,
SIGHT, TRACK TENSION IS WITHIN DECREASE TRACK TENSION, REMOVE 1 TRACK
ACCEPTABLE LIMITS. SHOE (FIG. 5-5) AND READJUST TRACK TENSION.
b. IF TOP OF CA NTEEN CUP IS ON OR BELOW
LINE OF SIGHT, TRACK IS TOO LOOSE. DECREASING TRACK TENSION
INCREASE TRACK TENSION AS REQUIRED,
AND REPEAT STEP 2 TO MAKE SURE TRACK OPEN PRESSURE BLEED PLUG ON TRACK
IS NOT TOO TIGHT. HYDRAULIC ADJUSTER AND REDUCE PRESSURE
INCREASING TRACK TENSION UNTIL TENSION IS ADJUSTED AS INDICATED IN
PUMP GREASE INTO PRESSURE INPUT FITTING STEP 3. TIGHTEN PLUG AND GREASE FITTING TO
WITH GREASE GUN UNTIL TENSION IS ADJUSTED 12-16 POUND-FEET.
AS INDICATED IN STEPS 1 THROUGH 3.
Figure 5-4. Checking and adjusting tack tension WE 12134
5-13
C6, T.M 9-2350-230-12
REMOVAL 3. INSERT CROW BAR THROUGH TRACK AND PRY

FORWARD OVER IDLER WHEEL TO PULL
1. BRING VEHICLE TO A COASTING STOP ON TRACK TAUT.
LEVEL GROUND WITHOUT APPLYING BRAKE.
4. INSTALL TRACK FIXTURE AND TIGHTEN UNTIL
2. LOOSEN PRESSURE RELIEF VALVE ON TRACK TRACK PIN HOLES ARE ALIGNED, USING
ADJUSTER TO RELIEVE TRACK TENSION. WRENCH 5120-288-9681 AND HANDLE 5120-449-
7042.
3. INSTALL TRACK FIXTURE BETWEEN IDLER
WHEEL AND NO. I ROAD WHEEL AND TIGHTEN 5. DRIVE DRIFT PIN FROM BEHIND, THROUGH
TO RELIEVE TENSION FROM TRACK PIN, USING TRACK PIN HOLES UNTIL FLUSH WITH FRONT
WRENCH 5120- 288-9681 AND HANDLE 5120-449- FACE OF SHOE.
7042.
6. DEPRESS CONNECTING SHOES 8 TO 9
4. REMOVE 1 TRACK PIN NUT AND CAREFULLY DEGREES WITH CROW BAR TO PROPERLY
DRIVE TRACK PIN OUT, USIN’G DRIFT PIN 5120- ALIGN HEX IN SHOES AND DRIVE TRACK PIN IN
678-2795. PLACE (SEE INSERT ABOVE).
5. REMOVE TRACK FIXTURE AND DRIVE VEHICLE 7. INSTALL 1 NUT AND TIGHTEN.
SLOWLY REARWARD UNTIL VEHICLE IS CLEAR
OF TRACK. 8. REMOVE TRACK FIXTURE AND ADJUST TRACK
TENSION (FIG. 5-4).
INSTALLATION
NOTE . IF EXCESSIVE TRACK SAG CANNOT BE
1. DRIVE VEHICLE FORWARD SLOWLY ONTO TAKEN UP WHEN ADJUSTING TRACK, REMOVE I
TRACK UNTIL REAR END OF TRACK ON TRACK SHOE AND READJUST TRACK TENSION.
GROUND MAY BE RAISED OVER AND ENGAGED
WITH DRIVE SPROCKET. 9. USE PAINT TO MARK TRACK SHOES WHERE
2. CONTINUE DRIVING FORWARD GUIDING TRACK NUTS HAVE BEEN DISTURBED.
OVER ROAD WHEELS AND STOP WHEN END OF
TRACK ON GROUND IS MIDWAY BETWEEN 10. NOTIFY ORGANIZATIONAL MAINTENANCE TO
IDLER WHEEL AND NO. 1 ROAD WHEEL. TORQUE NUTS DISTURBED TO 120-130 POUND-
FEET AS SOON AS POSSIBLE, AND AGAIN
NOTE. SHUT OFF ENGINE AND LEAVE PARKING AFTER 50 MILES.
BRAKE OFF. WE 12079 1
Figure 5-5. Removal/installation of track
5-14
C8, TM 9-2350-230-12
A VEHICLE WITH TRACK BLOWN OFF, DAMAGED ROADWHEELS, OR WITH BROKEN

IDLER WHEELS MAY BE SHORT-TRACKED ON ONE SIDE AND STILL BE ABLE TO
MANEUVER AT RESTRICTED SPEED SO LONG AS I DRIVE SPROCKET AND ANY
COMBINATION OF ROADWHEELS INDICATED IN STEP 1 . ARE INTACT
SHORT-TRACKING PROCEDURE
1. THE FOLLOWING ARE ROADWHEEL AND 6. DRIVE VEHICLE SLOWLY FORWARD, GUIDING
SPROCKET COMBINATIONS W/TRACK SHOE TOP OF TRACK TO +30-5: 00 O’CLOCK
REQUIRED (O INDICATES REMOVED POSITION AT FRONT OF LEAD WHEEL (SEE
ROADWHEEL). ILLUSTRATION ABOVE).
1-2-3-4-5-S (89R OR 91L)* 0-2-3-4-0-S (73R OR 75L) 7. USING TRACK FIXTURE, PULL ENDS OF TRACK
0-2-3-4-5-S (74R OR 76L) 0-2-4-0-S (73R OR 75L) TOGETHER AND INSTALL TRACK PIN (FIG. 5-5).
0-0-3-0-5-S (59R OR 61 L) 0-2-0-0-5-S (73R OR 75L)
0-0-3-4-5-S (60R OR 62L) 1-0-0-5-S (88R OR 90L) NOTE. . IN ORDER TO CONNECT TRACK, SOME
0-2-0-4-5-S (74R OR 76L) 1-0-0-4--S (88R OR 90L) SLACK MAY BE REMOVED BY BLOCKING BEHIND
0-2-3-0-5-S (74R OR 76L) 1-0-0-4-5-S (47R OR 49L) LEADING ROAD- WHEEL, BETWEEN WHEEL AND
TRACK. STEER’AWAY FROM SHORT-TRACKED
* LEFT TRACK REQUIRES 2 MORE SHOES THAN SIDE, AND VERY CAREFULLY APPLY:POWER IN
RIGHT TRACK DUE TO OFFSET OF TORSION FORWARD GEAR TO TIGHTEN TRACK .
BARS.
8. TIE UP ANY REMAINING ROADWHEEL ARMS TO
2. SELECT SECTION OF TRACK TO BE USED AVOID INTERFERENCE WITH OBSTACLES AND
(STEP 1). IF TRACI IS DAMAGED, SELECT DAMAGE TO SPINDLES AND ARMS.
LEAST DAMAGED SHOES. REMOVE OPERATION OF SHORT-TRACKED VEHICLE
REMAINDER OF TRACK AND STOW ON
VEHICLE. 1. DO NOT EXCEED 10 MPH FORWARD, 4 MPH
3. MANEUVER AND ALIGN THE SPECIFIED SHOE REVERSE, OR 2 MPH OVER EARTHEN MOUND
SECTION IN FRONT OF ROADWHEELS. OBSTACLE. PIVOT STEER AND OBSTACLE
NOTE. IT MAY BE NECESSARY TO BREAK CROSSING IS NORMAL EXCEPT AS IN- DICATED
TRACK INTO SMALLER SECTIONS FOR HANDLING. IN EXAMPLES ILLUSTRATED IN FIGURE 5-5.2.
RECONNECT THE SECTIONS. 2. AVOID PIVOT TURNS TOWARD SHORT-
4. DRIVE VEHICLE SLOWLY FORWARD ONTO TRACKED SIDE WHENEVER POSSIBLE.
TRACK. 3. GEARED STEER WILL REACT SLOWLY WHEN
5. AS SOON AS VEHICLE POSITION ON TRACK STEERING TOWARD FULL TRACKED SIDE, AND
PERMITS, GUIDE REAR END OF TRACK OVER QUICKLY TOWARD SHORT-TRACKED SIDE.
SPROCKET SO SPROCKET TEETH ENGAGE
TRACK(USE TRACK PIN OR DRIFT PIN TO GUIDE
TRACK ).
Figure 5-5.1. Emergency short-tracking procedure. (1 of 2)
5-14.1
C8, TM 9-2350-230-12
Figure 5-5.2. Emergency short-tracking procedure (2 of 2)
5-14.2
C2, TM 9-2350-230-12
TABLE 5-3. SPARE LAMPS - HULL
WHERE USED- FED.STOCK NO FIG/ITEM
* Driver’s Indicator Panel (MS 25237-327) 6240-155-7836 2-9
* Driver’s Switch Panel (MS 25237-327) 6240-155-7836 2-10
Dome Light (Red Lens) (MS 15570-623) 6240-019-3093 5-6/A
Dome Light (White Lens) (MS 35478-1691) 6240-295-2668 5-6/A
* C-2296/VRC Intercom Set Control (8168874) 6240-155-7967 5-6/C
* C-2297/VRC Intercom Set Control (8168874) 6240-155-7967 2-6/E
* Personnel Heater Control Box (11621411) 6240-950-1678 2-17
Coolant Heater- Control Box (11621411) 6240-950-1678 2-17
Blackout Stoplight (MS 15570-1251) 6240-019-0877 5-6/D
Blackout Marker Light (4 places) (MS 15570-1251) 6240-019-0877 5-6/B, C, D
Service Taillight (MS 15570-1251) 6240-019-0877 5-6/C
Service Stoplight (MS 35478-1683) 6240-044-6914 5-6/C
Blackout Drive Light (MS 35478-1683) 6240-044-6914 5-6/B
* Turn lens counterclockwise and remove. Remove lamp from lens.
5-15
TM 9-2350-230-12
Figure 5-6. Replacement of lamps - hull
5-16
C4, TM 9-2350-230-12
TABLE 5-4. DRAINING COOLANT AND FUEL SYSTEMS

DRAINING COOLANT SYSTEM (NORMAL TEMPERATURES TO -400F)

1 Traverse turret sideways and open engine left exhaust grille. 1-2/5
2 Remove surge tank filler cap. 5-2/A
CAUTION: If vehicle was previously operated, open surge tank filter
cap slowly to allow steam to escape.
3 Remove coolant drain plug hull access plug. 5-7/10
4 Remove coolant drain plug. 5-7/1
NOTE.
1. In temperate areas where the local ambient temperature is between
+80° and +32°', use 50% water and 50% antifreeze. Refer to
paragraph 1-6c for proper antifreeze to be used. If, and only if,
the recommended antifreeze is not available, use rust inhibitor
FSN 6850-753-4967 with clean soft water.
2. When operating vehicle with expected temperatures between +32°F to
-40°F, coolant system mixture is 50%water and 50%; antifreeze.
Start engine immediately after refilling to mix water and antifreeze.
Refer to paragraph 1-6c for proper antifreeze to be used.
3. When operating in temperatures of +80°F or over, fill with
6 gallons of clear water. Dissolve 22-1/2 ounces of inhibitor
(6850-753-4967) in 1 gallon of warm water and add to system while
engine is idling. Add sufficient water to fill system to operating
level. Record contents of coolant system on DD Form 1397 tag.
DRAINING COOLANT SYSTEM (-40°F. TO -650F TEMPERATURE)
1 Open engine left and right exhaust grilles. 1-2/5
2 Follow steps 2 through 4 above.
NOTE. Allow system to drain, then proceed to following steps.
3 Remove engine oil filter hull access plug and open drain cock on bottom 5-7/9, 10
of oil cooler.
4 Reach down over engine and open engine block left and right drain cocks. 5-7/8
5 Open thermostat housing drain cock. 5-7/7
NOTE. When operating vehicle with expected temperatures between
-40°F. to -65°F., use full strength antifreeze; refer to paragraph
i-6c.
DRAINING FUEL SYSTEM
1 Open 2 fuel tank valves. 5-3/A
2 Remove fuel tank drain hull access plug. 5-7/10
3 Remove fuel tank outlet hose drain plug, and drain fuel into suitable 5-7/4
container.
5-17
C6, TM 9-2350-230-12
Figure 5-7. Hull access plugs, power plant and fuel lank drain plugs
5-18
C9, TM 9-2350-230-12
Section 5-4. MAINTENANCE OF TURRET, CUPOLA, SIGHTING AND FIRE

CONTROL, AND MISSILE SUBSYSTEM UNITS
5-4. Crew Maintenance Instructions
The following tables and illustrations provide

maintenance instructions to be performed by the
crew.
TABLE 5-5. CREW MAINTENANCE - TURRET, CUPOLA, SIGHTING AND FIRE CONTROL,
AND MISSILE SUBSYSTEM
ITEM INSPECT TEST SERVICE ALIGN REPLACE
Azimuth Indicator Table 4-1 and Table 5-7

Fig. 2-27
M13A1C Elevation Quadrant Table 4-1 and Table 5-7
Fig. 2-28
Missile Subsystem Units Table 4-1 Table 2-12 Table 5-7 Table 2-12
Lamps Table 5-6
XM44 Series Periscope Table 4-1 and Table 5-7
Fig. 2-26 and B, Fig. 5-8
M47 Periscope Table 4-1 and Table 5-7 A, Fig. 5-8
Fig. 5-8
M48 Periscope Table 4-1 and Table 5-7 A, Fig. 5-8
Fig. 5-8
M1A1 Quadrant Fig. 2-28 Table 5-7
Ml19 or M127 Telescope Table 4-1 and Table 5-7
Fig. 2-25
TABLE 5-6. SPARE LAMPS - TURRET
WHERE USED FED.STOCK NO. FIG/ITEM
** Azimuth Indicator (MS 25236-8623) 6240-155-7864 2-27
* Cupola Control Assembly (MS 25237-327) 6240-155-7836 2-21
Dome Light (Red Lens) (MS 15570-623) 6240-019-3093 5-6/A
Dome Light (White Lens) (MS 35478-1691) 6240-295-2668 5-6/A
* Grenade Launcher Control Panel (MS 25237-327) 6240-155-7836 3-15
* Gun and Turret Control Selector (MS 25237-327) 6240-155-7836 2-19
* Loader’s Control Box (MS 25237-327) 6240-155-7836 3-1/A
5-19
C 10, TM 9-2350-230-12
TABLE 5-6. SPARE LAMPS - TURRET - Continued
WHERE USED FED.STOCK NO. FIG/ITEM
Night Vision Sight PVS2 6240-196-4519 2-29

(for Cal 50 Machine Gun) (MS35478-87)
Removal: Place rotary control switch in OFF position,
unscrew reticle lamp cap, and remove lamp.
* Radio Equipment (Call) (MS 25237-327) 6240-155-7836 7-4
Radio Equipment (Channel Dial) (MS 25237-327) 6240-155-7836 7-4
Removal: Turn lamp access cover counterclockwise

and remove. Remove lamp.
* Missile Subsystem Test Checkout Panel (MS 25237-327) 6240-155-7836 2-30
* XM44 Series Periscope Control Panel (MS25237-327) 6240-155-7836 2-26/6
XM44 Series Periscope Reticle (MS25231-316) 6240-817-9803 2-26/25
Removal: Unscrew receptacle assembly and remove

lamp.
* M119 or M127 Telescope Missile Reticle (8624583) 6240-921-4493 2-25/8
Removal: Press in and rotate reticle lamp housing

counterclockwise and remove. Press in and rotate
reticle lamp and remove.
M119 or M127 Telescope Conventional’ Reticle (86Z4583) 6240-921-4493 2-25/5
Removal: Release latch and open cover. Press and

rotate reticle lamp counterclockwise and remove.
* M119 or M127 Telescope Reticle Dimmer Box (MS25237- 6240-155-7836 2-25

327)
CAUTION: Be sure lamp of correct voltage rating is

used when replacing.
* Turn lens or jewel counterclockwise and remove. Remove lamp.
** Turn lamp counterclockwise and remove.
5-20
C4, TM 9-2350-230-12
TABLE 5-7. CLEANING AND INSPECTION - SIGHTING AND FIRE CONTROL AND MISSILE
SUBSYSTEM UNITS
COMPONENT INSPECTION AND CLEANING

INSPECTION
SIGHTING AND FIRE CONTROL NOTE. Check that all components are free from grease,
EQUIPMENT: dirt, foreign matter, rust, corrosion, and excessive
wear.
CLEANING
Metal Parts Use dry-cleaning solvent or mineral spirits to remove

grease, oil, and dry thoroughly. Avoid rubber parts.
Apply a light grade of lubricating oil to polished surfaces.
Rubber Parts Use soap and warm water. Apply coating of powdered
technical talcum to preserve.
Optical Surfaces Brush lightly with artists’s clean camel hair brush. To
remove oil or grease below +320°F, moisten lens tissue
paper with alcohol and clean.
CAUTION: Do not use polishing liquids, pastes, abrasives,

or cleaning cloths for cleaning lenses.
INSPECTION
MISSILE SUBSYSTEM UNITS: NOTE. Check that all components are free from grease,
dirt, foreign matter, rust, corrosion, and excessive wear.
CLEANING
Metal Parts Wipe equipment with a clean cloth to remove dust, dirt, or
grease at regular intervals and especially after operating
in muddy, sandy, or dusty terrain.
Optical, Surfaces Refer to cleaning optical surfaces above.
Transmitter Door Lubricate hinge and actuating rod (LO 9-2350-230-12).
5-21
C 10, TM 9-2350-230-12
Figure. 5-8. Removal/installation - M47 and M48 periscopes.

Figure 5-8.1 - deleted.
5-22
C 10, TM 9-2350-230-12
Section 5-5. MAINTENANCE OF ARMAMENT
5-5. Crew Maintenance Instructions b. Inspection. During maintenance of the

a. General. The following tables and illustrations components listed in table 5-8, inspect all parts for
provide maintenance instructions to be performed by the damage and proper functioning.
crew.
TABLE 5-8. CREW MAINTENANCE - ARMAMENT
ITEM SERVICE ADJUST REPLACE
CAUTION: Avoid damage to air cylinders, which are under very high pressure.
152MM Gun-Launcher and Mount:

Breech Actuating Mechanism Group Fig. 3-1
Bore and Breech Chamber Fig. 3-1
Obturator Seal Fig. 5-10. 1, 10. 2
and Table 5-8. 1
Evacuator Cylinder Fig. 5-10
Cleaning and Lubrication Table 5-8.1
Recoil Mechanism Table 5-8.1 Fig. 3-2
Counterrecoil Buffer Assembly Fig. 5-9
7.62MM Machine Gun Mount Fig. 2-24
Recoil Mechanism Reservoir Fig. 3-2
7.62MM Machine Gun and LO 9-2350-230-12 and Fig. 3-7

Flash Hider Figs. 5-11 through 5-13
Cal..50 Machine Gun LO 9-2350-230-12 Fig. 3-14
and Figs. 5-14, 15,
161 17
Figure 5-9. Checking and servicing counterrecoil buffer
5-22.1
C 10, TM 9-2350-230-12
Figure 5-10. Removal/installation - evacuator cylinder
5-22.2
C9, TM 9-2350-230-12
TABLE 5-8.1. CLEANING AND LUBRICATION OF GUN LAUNCHER (REFER TO FIG. 5-10.2)
DAILY CLEANING AND LUBRICATION (AT COMPLETION OF DAYS FIRING SCHEDULE)
1. Open breech and remove obturator seal (Fig. 5-10.1).
2. Using a soft rag, wipe residue, dirt, and foreign material from obturator seal, rear face of gun tube, seal cavity,
breech chamber front face, coupling and breech chamber buttress threads, and all exposed surfaces. DO
NOT USE STEEL WOOL.
3. Visually inspect all areas for cleanliness and reinstall obturator seal.
4. Apply coating of lubricating oil(PL-S) to all cleaned areas. Spread evenly with a clean saturated rag or brush.
Blow out detent cavity with dry compressed air. Make sure that coupling and breech chamber buttress
threads are well lubricated.
5. Hand crank breech chamber open and closed several times to check for smooth and normal operation. Leave
breech backed out but not rolled over to permit air circulation and reduce condensation. Return hand crank
to an approximate 12:00 o’clock lockout position.
6. Before firing, wipe dry all areas except coupling and breech chamber buttress threads. Maintain lubricant on these
threads at all times.
7. Clean gun/launcher tube with RBC (M81 tube - also clean evacuator valves and chamber, Fig. 5-10).
8. Notify organizational maintenance to service detent as necessary after days firing but not to exceed 40 rounds.
Additional checking and cleaning is recommended if a prolonged period between firing missions exists.
NOTE. After firing 200 rounds, notify organizational maintenance to remove firing probe and inspect probe
and breech chamber for erosion (Table 5-1).
9. (M81E1 and M81 Modified) Notify organizational maintenance to service check valve at least every 100 rounds.
More frequent cleaning is recommended if carbon buildup or decrease in CBS air volume is suspected,
CLEANING AND LUBRICATION AT COMPLETION OF FIRING MISSION AND WHEN WEAPON WILL NOT BE USED
FOR EXTENDED PERIODS
1. Immediately after firing and on next two following days thereafter, open breech, remove obturator seal, and
thoroughly clean bore and breech chamber with RBC, (MIL-C-372) insuring that all powder-contacting
surfaces (including rifling) are well coated. Do not wipe dry.
2. On third day after firing, clean bore with RBC, using RBC and a non-scratch pad or stiff bristle brush, wash
obturator seal, breech chamber, front face and exposed surfaces, gun tube rear surface and seal cavity, and
coupling threaded area. DO NOT USE STEEL WOOL..
(M81 only) On third day after firing or monthly if cannon is not being fired, remove evacuator and valves (Fig.
5-10). Clean all powder contacting surfaces with RBC. Wipe dry and apply a thin coating of PL-S. Apply GG
at temperatures above 0°F and GAA below 0°F to threaded portions of evacuator and thrust collar before
assembling.
5-24.1
C9, TM 9-2350-230-12
TABLE 5-8.1. CLEANING AND LUBRICATION OF GUN LAUNCHER - CONT’D.
3. Wipe dry with clean, lint-free cloth and blow out detent cavity with dry compressed air.
NOTE. On vehicles equipped with closed breech scavenger system, close breech and activate scavenge
system manually to clear check valve discharge port in tube.
4. Visually inspect for complete removal of residue, rust, and foreign matter.
5. Coat all cleaned surfaces with lubricating oil PL-S. Spread oil with a clean saturated cloth or brush. Leave breech
backed out but not rolled over to permit air circulation and reduce condensation.
NOTE. If cannon will not be fired for one month or longer, use grease, aircraft and instrument GIA (MIL-G-
23827).
6. Monthly thereafter, when cannon is not being fired, clean with RBC, wipe dry and relubricate as indicated in
Step 5.
6A. In geographical areas where temperature variations create excessive moisture by condensation, crew
maintenance should include WEEKLY removal of gun launcher dust shield, drying of all affected components
and assuring that exposed portion of recoil mechanism sleeve is free of corrosion or rust. External surface of
exposed sleeve may be thinly coated with Silicone Compound MIL-S-8660.
7. Wipe dry before firing all areas except breech chamber and coupling buttress threads. Maintain lubricant on these
threads at all times.
8. Notify organizational maintenance to service check valve and/or detent (table 8-17. 1).
TABLE 5-9. DISASSEMBLY/ASSEMBLY - 7.62MM MACHINE GUN
DISASSY ASSY PROCEDURE FIG/ITEM

STEP STEP
Removal/installation of machine gun from vehicle. Fig. 3-7
WARNING: Ammunition belt must be removed from the

machine gun and chamber cleared.
NOTE. White arrows in figures 5-11 through 5-12 indicate Fig. 5-11
disassembly sequence, black arrows, assembly sequence.
1 13 Barrel extension assembly is in rear position (charged),

place trigger safety in the fire "F" position. Pull charger
handle rearward and, while keeping tension on handle,
depress manual firing trigger, allowing barrel extension
to go forward slowly. Charge the machine gun, then
place safety in safe "S" position. Depress the manual
firing trigger. If the barrel extension assembly is
released, notify organizational maintenance personnel.
Functional Check - Check the functioning several times by

pulling charger to rear, and while maintaining tension
on handle, depress the manual firing trigger. Barrel
extension must release with safety in fire "F" position.
5-24.2
C6, TM 9-2350-230-12
TABLE 5-9. DISASSEMBLY/ASSEMBLY - 7.62MM MACHINE GUN - Continued
STEP STEP
NOTE. Use dummy cartridges to check functioning of machine gun.
2 12 Pull right side disconnector pull ring rearward, rotate Fig. 5-11.1
jacket assembly with bearing group counterclockwise
until mounting block is free of receiver assembly. Push
jacket assembly with bearing group forward and remove
from receiver assembly.
NOTE. When installing, position jacket assembly mount-

ing block, hold on one disconnector pull ring, pull out on
opposite disconnector pull ring, rotate the group into
position, release ring.
3 11 To remove, pull barrel assembly from jacket assembly Fig. 5-11.1

with bearing group. When installing, position barrel
assembly into rear of jacket assembly with bearing
until slot in barrel is alined with barrel locator. Push
barrel forward until stopped by locator.
WARNING: Turn barrel assembly to make certain

barrel locator enters barrel slot.
4-5 9-10 Remove cover assembly from receiver assembly. When Fig. 5-11.2
installing position cover assembly on cover latch rod
assemblies, then press down on cover until it locks
in position.
NOTE. Cover latch rod assemblies in locked (forward)

position. Locks are released automatically by cover
assembly when installed.
6 8 Lift up and remove feed tray group. When installing position Fig. 5-11.2
feed tray group with cartridge stop on the right of the
receiver.
NOTE. Feed tray group may be removed or installed with

cover assembly.
WARNING: Make certain that the barrel extension assembly

is in forward position to prevent injury to personnel.
7 7 Push guide rod assemblies forward, rotate 1/4 turn counter- Fig. 5-11.2
clockwise to unlock, then remove rod assemblies and
compression helical springs from holes in back plate
assembly with solenoid. To install, position springs on
guide rods, insert in holes in back plate, and into holes
in rear of barrel extension, compress and rotate clock-
wise until secure.
8 6 Slide back plate assembly with solenoid upward and remove Fig. 5-11.2
from receiver assembly. To install, aline grooves on
back plate with flanges on receiver assembly and push
downward.
5-25
C6, TM 9-2350-230-12
TABLE 5-9. DISASSEMBLY/ASSEMBLY - 7.62MM MACHINE GUN - Continued

STEP STEP
CAUTION: Slamming of the back plate during installation

will lower the receiver tabs and create a "runaway" gun.
9 5 Pull rearward on charger handle of charger assembly until Fig. 5-11.2

barrel extension group is fully retracted.
WARNING: Use the hand charger assembly handle to

retract barrel extension assembly. Never use the hands.
NOTE. Depress right- or left-hand buffer support

lever to release and/or install the barrel extension group.
10 4 Grasp top portion of barrel extension assembly, depress Fig. 5-11.2

buffer support lever, then pull rearward and slide
barrel extension group from receiver assembly. To
assemble, aline barrel extension assembly camway with
barrel extension rail on receiver, depress buffer support
lever, then push barrel extension fully forward.
11 3 Slide top portion of breechblock assembly left to center of Fig. 5-12

barrel extension channel in barrel extension assembly,
then lift straight up to remove. To install, position top
portion of breechblock assembly in center of barrel
extension channel, lower to align with breechblock
camways, then slide breechblock to right.
NOTE. Right top edge of breechblock assembly must

align (flush) with right top edge of barrel extension assembly
when installing in the machine gun.
12 2 Remove retaining ring from charger mounting stud on Fig. 5-12

receiver assembly that secures the charger assembly
to receiver assembly.
13 1 Pull hand charger off charger mounting stud and disengage Fig. 5-12
front end of charger from buffer pivot pin on receiver
assembly. To install, position the forward end of
charger on pivot pin, slide in position on charger
mounting stud, then secure charger to stud with
retaining ring.
5-26
C9, TM 9-2350-230-12
REMOVAL
INSERT SCREWDRIVER 5120-287-2130 BETWEEN
GUN TUBE AND OBTURATOR GAS SEAL AND PULL
TO
SNAP SEAL OUT OF SEAT IN GUN TUBE.
CLEANING
REFER TO TABLE 5-8.1.
INSTALLATION
POSITION SEAL IN GUN TUBE AND SNAP INTO
PLACE
IN SEAT IN GUN TUBE.
CAUTION: USE PROPER TOOL AND EXTREME

CARE DURING REMOVAL AND INSTALLATION
TO AVOID DAMAGE TO THE SEAL.
WE 12162
Figure 5-10.1. Removal/installation - obturator seal
Figure 5-10.2. Gun-launcher buttress threads, and ammunition detent and scavenger openings
(5-24 blank)/5-23
C6, TM 9-2350-230-12
Figure 5-11. Disassembly/assembly - 7.62 mm machine gun (1 of 4)
5-26.1
C6, TM 9-2350-230-12
Figure 5-11.1. Disassembly/assembly - 7.62mm machine gun (2 of 4).
5-26.2
C6, TM 9-2350-230-12
Figure 5-11.2. Disassembly/assembly - 7.62mm machine gun (3 of 4).
5-26.3
C6, TM 9-2350-230-12
Figure 5-12. Disassembly/assembly - 7.62 mm machine gun (4 of 4)
5-26.4
C6, TM 9-2350-230-12
Figure 5-13. Removal/installation - 7.62 mm machine gun flash hider
5-27
(5-28 Blank)
TM 9-2350-230-12
TABLE 5-10. DISASSEMBLY/ASSEMBLY OF CAL..50 MACHINE GUN, M2, HB

STEP STEP
1 22 Pull retracting slide handle to rear until lug on barrel locking 5-14
spring is visible and centered. Twist barrel and remove.
2 21 Raise cover and remove belt holding pawl pin and link stripper. 5-14
3 20 Remove belt holding pawl pin, belt holding pawl, and springs. 5-14
* CAUTION: Make certain bolt is in forward position
before next step.
4 19 Pull outward on lock, upward on latch and slide back plate 5-14
from receiver grooves.
5 18 Push driving spring rod assembly forward and to the left 5-14
until free from hole in side of receiver.
6 17 Retract retracting slide handle until headless shoulder pin (bolt 5-14
stud) is aligned with slot in receiver and remove bolt stud.
7 Push bolt to the rear and remove. 5-15
16 Raise bolt latch and push bolt into receiver.
15 Make certain cocking lever is forward and push bolt into receiver
until bolt latch engages notches in top of bolt.
* CAUTION: When installing bolt in next step, do not
trip accelerator.
8 Remove bolt assembly extractor and bolt switch. 5-15
14 Install bolt assembly extractor and bolt switch so that grooves 5-15
in switch align with grooves of bolt for left-(L) hand feed.
9 13 Release bolt assembly firing pin spring by depressing plunger. 5-15
10 12 Remove bolt assembly cocking lever pin using punch and
remove cocking lever.
11 Remove bolt assembly accelerator stop lock by depressing 5-15
and rotating to center of bolt. Pry up by using thin end of
cocking lever and remove.
11 Install accelerator stop lock by placing in position. 5-15
12 Push accelerator stop from opposite side shown, using
cocking lever, then pry stop from bolt.
10 Install accelerator stop and press into position. 5-16
13 9 Remove sear slide, sear, and sear spring. 5-16
* CAUTION: Seat sear spring properly.
14 8 Remove firing pin extension with firing pin and separate. 5-16
15 7 Depress buffer body lock and push barrel extension to the rear. 5-16
Remove buffer assembly with barrel extension assembly.
16 Push forward on tips of accelerator and disconnect buffer 5-16
assembly from barrel extension assembly.
6 Hold buffer assembly with accelerator tips up, engage de- 5-16
pressor in notch and push forward to engage.
17 5 Remove buffer assembly from barrel buffer body. 5-16
18 4 Remove accelerator pin and accelerator from buffer body. 5-17
19 3 Remove breech lock pin and breech lock from barrel extension. 5-17
20 2 Remove belt feed lever group and belt feed slide. 5-17
21 1 Turn trigger bar pin assembly, pull out and remove trigger 5-17
bar.
NOTE. Reverse disassembling step action, as necessary, when assembling.
5-29
TM 9-2350-230-12
Figure 5-14. Disassembly/assembly - cal..50 machine gun, M2, HB (1 of 4)
5-30
TM 9-2350-230-12
Figure 5-15. Disassembly/assembly - cal..50 machine gun, M2, HB (2 of 4)
5-31
TM 9-2350-230-12
Figure 5-16. Disassembly/assembly - cal. .50 machine gun, M2, HB (3 of 4)
5-32
TM 9-2350-230-12
Figure 5-17. Disassembly/assembly - cal. .50 machine gun, M2, HB (4 of 4)
5-33
TM 9-2350-230-12
This page is left blank intentionally.
5-34
C4, TM 9-2350-230-12
CHAPTER 6
PREPARATION FOR AIR-DELIVERY STORAGE,
AND DESTRUCTION OF MATERIEL TO
PREVENT ENEMY USE
Section 6-1. PREPARATION FOR AIR-DELIVERY
6-1. Preparation for Air-Delivery maintenance checks and services. The crew may assist
The crew will lubricate vehicle (LO 9-2350-230-12) Air Force personnel in preparation of vehicle for air
and perform all before and/or after operation preventive- delivery.
TABLE 6-1. PREPARATION FOR AIR-DELIVERY
CAUTION: Vehicles with serial number 1 through 69 will require 6-2

blocking under turret rotatable floor prior to air drop.
1 Disconnect 3 wiring harness quick-disconnectors from cupola traverse 2-4/2, 4, 6

control switch assembly.
2 Remove 50 cal.. ammunition tray. 2-4
3 Stow ammunition tray. 6-1
4 Remove machine gun and cradle and pintle assembly. 3-14
5 Stow machine gun and cradle and pintle assembly. Place cushion
material in ammunition tray to support machine gun barrel when in
stowed position.
6 Remove 4 screws and flat washers securing pintle support and remove 2-4/1
pintle support.
7 Place screws and flat washers in a bag with a 15/16 socket tee wrench 6-1
and secure to pintle support. Stow support. Place cushion material
under pintle support travel lock to prevent damage.
8 Raise cupola left and right hatch covers, remove 10 screws and hatch 2-4
covers. Place screws in a bag with 3/4 socket tee wrench, and
secure to right hatch cover.
9 Stow hatch covers and tie down antennas. 6-1
10 Turn turret control system on (table 2-7).
11 Depress palm switch of either control handle. Keep handle centered 2-19 and
within the system neutral zone. 2-22/11
11.1 On vehicles equipped with spring clips behind air drop knobs, remove
spring clips and stow. Clips must be reinstalled after drop.
12 With palm switch depressed, turn 2 air drop knobs on elevating 2-19
mechanism clockwise until firm resistance is met, One knob is
located beneath handwheel and the other diametrically opposite.
13 After air drop knobs are firmly in place, release palm switch and
turn turret control system off (table 2-7).
NOTE. The gun-launcher should be free to move into air-drop

padding by applying pressure to end of gun tube. If gun-launcher
is not free, follow steps 14 through 17, turn manual elevation
handwheel one complete turn and repeat steps 10 through 13.
6-1
C4, TM 9-2350-230-12
TABLE 6-1. PREPARATION FOR AIR-DELIVERY--CONTINUED
AFTER AIR-DELIVERY
14 Turn turret control system on, table 2-7.
15 Depress palm switch of either control handle keeping it centered within 2-19 and
system neutral zone. 2-21/11
16 With palm switch depressed, turn 2 air drop knobs on the elevating 2-19
mechanism counterclockwise until firm resistance is met.
17 Release palm switch and turn turret control system off, table 2-7.
NOTE. The weapon system is now in manual mode and ready

for operation.
18 Install items removed in steps 1 through 9, and 11.1.
NOTE. Remove air drop blocking from under turret rotatable 6-2
floor prior to operation on vehicles serial No. 1 through 69Y.
Figure 6-1. (Superseded) Stowage locations of items removed for air-delivery
6-2
C3, TM 9-2350-230-12
Figure 6-2. (Added) Blocking under turret rotatable floor for air-delivery (vehicles serial no. 1 through 69 only)
Section 6-2. STORAGE
6-2. Servicing and Processing Vehicle for Storage good protection against moisture and must have
adequate ventilation.
a. Servicing Vehicle. Perform all before an4/or
after- operation preventive- maintenance checks and (2) Outside storage sites may be utilized when
services and lubricate in accordance with LO 9-2350- adequate buildings are not avail-able.
230-12 (Appendix IV). Missiles stored outside must be stacked 6
inches off the ground on dunnage and
b. Processing Vehicle for Storage. Reverse covered with paulins or other suitable
deprocessing vehicle procedure (table 2-1). covering. The covering must allow free
circulation of air among the containers.
6-3. Missile Subsystem Shipment and Storage Suitable trenches should be dug to prevent
water from running under the stacks.
a. Shipment of Missiles. The shipping and storage
container provides adequate shock and vibration (3) Missiles should be stored with NOSE END
protection for the SHILLELAGH missile during transit, pointing in the direction which offers the
provided the containers are securely tied down and minimum hazard to personnel and property
braced on the transporting vehicle. During air shipment, in event of accidental ignition.
a self-operating pressure relief valve protects the missile
and container. (4) Do not stack more than six-containers high.
b. Storage of Missiles. (5) The storage temperature limits on the

(1) Missiles should be stored in buildings containers must not be exceeded.
designed, designated, and isolated for the
specific purpose of storing am-munition as (6) Missiles must be stored in accordance with
specified in TM 9-1300-206. Explosives quantity-distance classification and storage
and ammunition will not be stored in compatibility group (table 7-1). Distance
buildings which are used for other must be computed using the total explosive
purposes. When specially constructed weight of the missile (table 7-1).
magazines (as specified in TM 9-1300-206)
are not avail-able, the building used must
offer
6-3
C3, TM 9-2350-230-12
c. Inspection of Stored Missiles. Missiles stored or using and supporting activities. This can be
held at the organizational unit must be inspected at least accomplished by a Method m package which provides
weekly (more often if stored outside during bad weather) mechanical and physical protection only. Items to be
to insure that the humidity indication does not exceed the packaged as follows: Wrap item in chemically neutral
"40" level. If the indication exceeds this level, the paper (FSN 8135-558-1245). Overwrap item in
dessicant and humidity indicator card must be replaced. cushioning material (FSN 8135-584-3114) and place in
d. Shipment of Missile Subsystem Units. Items fiberboard container (FSN listed in SB 38-100 by box
which are repairable at direct support and general size). Fill all voides with cushioning material, seal
support activities should be provided adequate container with tape (FSN 8135-297-6655). Materials are
mechanical and physical protection in transit between the identified in SB 38-100.
Section 6-3. DESTRUCTION OF MATERIEL TO PREVENT ENEMY USE
6-4. Destruction Methods and Priority Destruction must be extensive and by methods and
Attempt to salvage sighting and fire control priorities listed in following table so as to prevent repair
equipment and short supply items prior to destruction. of cannibalization by the enemy.
TABLE 6-2. DESTRUCTION OF MATERIEL
METHODS:
Burning........................................................... Gasoline, oil or incendiary grenades.

Mechanical..................................................... Axe, crowbar, pick mattock, sledge, or other heavy implement.
Demolition ...................................................... Ammunition or demolition charges.
Gunfire ........................................................... Artillery, hand grenades, or anti-tank rockets.
PRIORITY:
Missile Sub-
system ........................................................ Transmitter
................................................................. Tracker (mounted on M149 telescope mount).
................................................................. Signal Data Converter
................................................................. Modulator
Sighting and Fire

Control Equip-
ment............................................................ XM44 Periscope
................................................................. M119 Telescope
................................................................. Night Vision Sight (Cal. .50 Machine Gun)
................................................................. M48 Periscope
152MM Gun-
launcher ...................................................... Breech Mechanism
Turret Electric
Drive Control............................................... Accessory Box
................................................................. Amplifier Integrator
................................................................. Power Supply Assembly
................................................................. Gyro Selector
Missiles .......................................................... Fire in direction of enemy or destroy in conjunction with vehicle.
Machine Guns................................................ Receiver
Power Plant.................................................... Destroy in conjunction with vehicle.
6-4
C9, TM 9-2350-230-12
CHAPTER 7
MATERIEL USED IN CONJUNCTION WITH MAJOR ITEM
Section 7-1. 152MM GUN-LAUNCHER GUIDED MISSILES
7-1. Firing Tables and Precautions b. General Firing Precautions. TM 9-1300-206 and
a. Firing Tables. DA Pam 310-3. AR 385-63.
TABLE 7-1. SHILLELAGH AMMUNITION DATA CHART
NOMENCLATURE GUIDED MISSILE GUIDED MISSILE

SURFACE ATTACK PRACTICE
MGM-51A MGM-51B MGM-51C MTM-51A MTM-51B MTM-51C
1
FSN 1410-999- 1410-878- 1410-878- 1410-999- 1410-878-- 1410-878
0857 7219 7219 0132 7218 7218
Part Number 10070000 10154031 10153399 10121359 10153071 10153400
Missile color data;

2
Rocket motor section Olive drab Olive drab
Color of data markings Yellow White
Color code markings of Black with 2-inch yellow band over Olive drab with 2-inch blue band
3
nose cone black over olive drab
Container color data:

Olive drab Olive drab
Basic overall color
Yellow Brown
Four inch corner
4
squares
Yellow White
Data marking color
ICC shipping name ROCKET AMMUNITION WITH ROCKET AMMUNITION WITH

on container EXPLOSIVE PROJECTILE INERT LOADED PROJECTILE
Shipping classification CLASS A EXPLOSIVE CLASS B EXPLOSIVE
ICC placard type EXPLOSIVE DANGEROUS
Quantity distance 7 2
classification
group F F
1
FSN applies to the missile and container as a unit of issue.
2
Live rocket motor will have a 2-inch brown band around the motor case.
3
The word INERT is stamped on the blue band in four places, 90 degrees apart.
4
Container corner markings are on diagonally opposite corners.
7-1
C9, TM 9-2350-230-12
TABLE 7-2. SERVICE UPON RECEIPT OF MISSILES
ITEM ACTION REQUIRED

MISSILE CONTAINERS:
Data Marking and Color Coding ...................................... Make sure correct type of missiles has been received.
Lead Seals....................................................................... Must not be broken from latches.
Surfaces. ......................................................................... Must not be punctured.
Humidity Indicator ........................................................... "40" and "50" dots must not be pink.
NOTE. If containers are defective do not open.

Return MISSILES to ammunition supply point. Report
discrepancies on DA Form 2415.
REMOVAL
MISSILES............................................................................. NOTE. Except to perform inspections required

in Table 7-2. 1, missile containers must not be
opened until immediately prior to stowing missiles
in vehicle.
1. Depress pressure relief valve on container lid to

relieve any pressure.
2. Cut seals, unlatch and remove container lid.
3. Remove missile from container.
NOTE. 1. Exercise care in unpacking missiles

from containers to avoid denting or damaging missiles.
2. If humidity indicator "40" or "50" dot is
pink return missile and container to ammunition
supply point.
4. Replace lid on container.
5. Return all containers that are excess to unit

requirements to the ammunition supply point.
INSPECT
Surface ............................................................................ Must not be dented, cracked, scratched, or corroded.
WARNING: Reject all HEAT warhead missiles that

have dented nose cones.
NOTE. Scratches that have not displaced metal

are permitted.
Shorting Connector.......................................................... Must fit tight and its surface must not be higher than
surface of missile skin. FWD arrow must point to-
ward nose cone.
Assembly Attachment Points........................................... All must fit tight and joints at attachment points must
not be loose.
Nose Cone Seam ............................................................ Must not be separated.
Color Coding and Data Markings .................................... Make sure correct type of missiles have been received.
7-2
C9, TM 9-2350-230-12
TABLE 7-2. SERVICE UPON RECEIPT OF MISSILES - Continued
ITEM ACTION REQUIRED
MISSILE AFT COVER:

Shear Screws Must be tight.
Ejector Rim Must not be dented.
Adapter Stop Must not be dented.
Cushioning Pads Not rolled or defaced.
Observation Windows Tight and not cracked. No evidence of internal moisture.
Firing Contractor Must fit tight.
Diaphragm Sealed and has no punctures.
NOTE. IF missile fails to pass any of the above checks, repack missile in its container and return to ammunition supply
point. Report discrepancy on DA Form 2415.
Figure 7-1. Missile inspection points
7-3
C 10, TM 9-2350-230-12
TABLE 7-2.1. SHILLELAGH AMMUNITION PERIODIC INSPECTION REQUIREMENTS
ITEM INSPECT
NOTE. Semiannual inspection will be performed by a contact team from the ammunition company. Notify the
supporting organization where inspections can be scheduled.
MISSILE CONTAINERS:
Humidity Indicator Inspect the humidity indicator on all containers on a

monthly basis, in accordance with table 7-2.
MISSILE AND CONTAINER: Semiannual visual inspection on a sampling basis of

basic load stock.
Annual missile test on a sampling basis of basic

load stock.
Dummy Guided Missile M29 and Semiannual visual inspection will be performed on
M29A all dummy missiles.
Figure 7-2. Missile identification
7-4
C 10, TM 9-2350-230-12
Section 7-2. CONVENTIONAL AMMUNITION FOR
152MM GUN-LAUNCHER M81 SERIES
7-2. General identification. Color codes used are given in table 7-3.
a. Conventional ammunition for 152MM Gun- 7-5. Authorized Rounds

Launcher M81/M81E1 is classified as fixed ammunition. Only authorized cartridges will be used in this
The complete round is issued with projectile assembled weapon. Specific information, Federal Stock Numbers
to the cartridge case. The propelling charge is not and other pertinent data are listed in SC 1305/30-IL and
adjustable. SC 1340/98-IL.
b. A complete round of ammunition consists of all 7-6. Preparation for Loading

components required to fire the weapon once. These a. General. Cartridges for 152MM Gun-Launcher
components consist of a primed cartridge case M81 series are fixed rounds and require no preparation
containing the propelling charge and a projectile, fuzed for firing except unpacking and inspection. Rounds are
or unfuzed depending on type. The complete round is marked for identification as shown in figure 7-3.1 through
loaded into the weapon as a unit. Dummy round, a one 7-3.4.
piece inert round made of cast aluminum, is used for b. Firing Temperature Limits. Observe the following
training in loading and handling. safe temperature limits:
c. Authorized cartridges, round types and fuze For all models except HE-T cartridge XM657E2:
types are given in table 7-3, and illustrated in figures 7- Upper limit ..................................................... +1250F
3.1 through 7-3.4. Lower limit .......................................................... -40 F
7-3. Firing Tables For HE-T cartridge XM657E2 only:

Upper limit ............................................ +1250F
Refer to FT 152-A-1. Lower limit ................................................ t40 F
7-4. Identification NOTE. Ammunition kept clean, dry, and at uniformly

moderate temperatures gives greater accuracy of fire.
a. General. Ammunition, ammunition components, Successive firing of cartridges from the same lot
and packing containers are identified by painting and minimizes dispersion at the target.
marking. Complete rounds are identified by color
scheme and marking. c. Special Instructions for Cartridge Canister, M625
Series.
(1) Model. A model designation, assigned to
identify a particular design, is included in WARNING: Before firing, assure that all personnel
the marking. Model designations consist of are clear of dispersion area proper and are under cover
M or XM and an arabic numeral. in immediate vicinity.
Modifications are indicated by adding A or
E and an arabic numeral. M1A1, for Canister cartridge M625 series is a flechette-loaded,
example, indicates the first modification of beehive type which functions immediately in front of the
an item for which the original designation weapon. The flechettes are dispersed in a conical
was M1. XM 409E5, as another example pattern (fig. 7-3.5). This presents no hazard to
indicates the fifth modification of an item personnel except in the cone area and immediate
originally designated XM409. vicinity.
(2) Ammunition lot number. When
ammunition is manufactured, an NOTE. Before firing canister cartridge, adjust
ammunition lot number, consisting of the telescope reticle for a range of 1400 meters. This
manufacturer’s symbol and a number, is assures desired gun elevation of 17 mils.
assigned.
b. Painting. Artillery projectiles are painted to
prevent rust and to provide a ready means of
7-4.1
C10, TM 9-2350-230-12
d. Unpacking and Stowing. CAUTION: Do not use axes, crow- bars or other
implements which may damage inner pack or
NOTE. Retain packing materials for repackaging, as ammunition.
required.
(b) Open outer pack.
(1) Packaging.
(c) Remove bagged fiber container.
(a) In order to protect the nonmetallic
cartridge case from moisture, each round (d) Remove laminated barrier bag covering
is packed in an elastomeric (stretchy fiber container.
rubber) or neoprene barrier bag as follows:
(e) Open fiber container and remove bagged
(1) Rounds with cartridge cases M205 cartridge and desiccant bags.
(table 7-3) are packed in elastomeric
barrier bags. These cover the (f) Immediately inspect projectile and outside
cartridge case and extend flat up the of barrier bag for moisture. Reject
projectile body beyond the rotating rounds which fail to pass this inspection
band. and return to ASP for disposition. Do not
use humidity indicator card on bag as I
(2) Rounds with cartridge cases M157 inspection criterion,
series (table 7-3) are packed in
neoprene barrier bags. This bag CAUTION. Do not remove barrier I bag which covers
covers the cartridge case and is cartridge case until round is being chambered.
drawn tight around the base of the
projectile, with a cuff folded back. (g) Check markings on projectile to confirm
On cartridge M625 XM625) ONLY, identification of round.
the bag extends flat up the projectile
body. (h) Before placing round in stowage rack, fit
protective cover (issued with vehicle) over
(b) A warning stenciled on each bag advises cartridge case. Unfold cuff of barrier bag
the user to "REMOVE THIS BAG so that it extends flat, covering projectile
IMMEDIATELY PRIOR TO FIRING." rotating band inside protective cover.
(2) Marking of packaging. Markings on outer NOTE. This protective cover is used over
and inner pack are given in table 7-3.1. elastomeric and neoprene barrier bags as additional
protection for ammunition stowed on board vehicle.
(3) Procedure.
(a) Examine ammunition box markings to

determine identification.
Figure 7-3-deleted.
7-4.2
C5, TM 9-2350-230-12
Figure 7-3.1. 152MM HE-T cartridge XM657E2
Figure 7-3.2. 152MM canister cartridge XM625
7-4.3
C5, TM 9-2350-230-12
Figure 7-3.3. 152MM HEAT-T-MP cartridge XM409E5
Figure 7-3.4. 152MM TP-T cartridge XM411E3
7-4.4
C10, TM 9-2350-230-12
TABLE 7-3. ROUND TYPES AVAILABLE FOR 152MM GUN-LAUNCHER M81 SERIES
IDENTIFICATION
ROUND CARTRIDGE’ COLOR OF LOADING OF ACTION OF TACTICAL
CASE PROJ MARK ROUND FUZE USE
Cartridge, 152-mm: XMI57 Olive drab Yellow High explo- Super- Antipersonnel,
HE-T, XM657E2 w/ sive, TNT quick antimateriel
Fuze, PD: XM720E1
Cartridge, 152-mm: M205 Black Yellow High explo- Super- Armor de-
HEAT-T-MP, quick sive, shaped feating, anti-
M409A1 w/Fuze, charge personnel,
PIBD: M539 (Comp B), antimateriel
tracer
Cartridge, 152-mm: M157 Same Same Same Same Same
HEAT-T-MP,
M409 (XM409E5)
w/Fuze, PIBD:
M539 (XM539E4)
Cartridge, 152-mm: M205 Olive drab White Flechette Unfuzed Antipersonnel

Canister, M625A1 (white (effective in
diamond dense foliage)
s
indicate
fle-
chettes)
Canister, M625
(XM625)
Cartridge, 152-mm: M205 Blue White Inert pro- Unfuzed Target

TP-T, M411A3 jectile with practice
tracer
Cartridge, 152-mm M157 Same Same Same Same Same
TP-T, M411A2
TP-T, M411A1
(XM411E4)
Cartridge, 152-mm: M157 Same White Inert pro- Super Same
with one jectile w/ quick
yellow live fuze,
band tracer, and
spotting
charge
Cartridge, 152-mm: Blue White Inert Unfuzed Training

Dummy M596
7-4.5
C 10, TM 9-2350-230-12
NOTE. APPROXIMATELY A 10.5-METER INCREASE

IN ARC WIDTH RESULTS FOR EACH ADDITIONAL
50 METERS OF RANGE.
Figure 7-3. 5. Dispersion pattern - canister cartridge M625 series.
Table 7-3.1. Marking of Packaging
Markings Outer Pack Inner Pack

(Fiber Container)
Department of Transportation
(DOT) Shipping Designation X
Federal Stock Number (FSN) and

Department of Defense Identification X
Code (DODIC)
Department of Defense x
Ammunition Code (DODAC)
Ammunition Lot Number X X
Gross weight of packing container X

and contents
Cubical displacement of packing x

container
Date manufactured X
Descriptive nomenclature of x x
packed item
Caliber and weapon designation X X
7-4.6
C 10, TM 9-2350-230-12
7-7. Preparation for Firing k. If firing is interrupted, remove round From

a. Remove ballistic protective cover. Remove chamber of hot weapon promptly to prevent cook-off.
round from rack. (See chapter 3).
b. Assure that round is free of sand, mud, snow,
ice, grease or other foreign matter. Contamination may NOTE. Repeated loading and unloading of the same
result in hot residue in gun chamber. round may result in a misfire.
c. Check cartridges visually for damage to
projectile body, ogive, rotating band and band coating 7-8. Cartridges Prepared for Firing But Not Fired
which might result in difficulty in chambering the round.
d. Do not use firing mechanism adapter when firing CAUTION: Do not reuse cartridges which have been
rounds assembled with cartridge cases M205. ejected from weapons by ramming. Ejection difficulty
e. Assure that area to rear of forcing cone in tube may have been caused by some nonstandard condition
and chamber is clear of residue. in the ammunition and, also, the fuze may have been
f. Assure that internal portion of breech U damaged during the ramming process.
(including firing mechanism) and chamber of cannon are a. Assure that detent pin is in the retracted position
dry. prior to any removal action. (Detent pin must be held in
g. Remove barrier bag as cartridge is shoved into retracted position while round is being dechambered).
gun tube, checking for obvious case and primer damage b. Do not use missile cap extractor to remove
which might result in difficulty in chambering the round. round from chamber. (Extractor is intended only for fired
h. If any pieces of smoldering residue are visible missile cap.) Ram cartridge gently if it cannot be
after firing, do not remove barrier bag of subsequent removed by hand. Take care to catch rammed round
round until residue is extinguished and gun tube cleared. before it drops to floor of vehicle.
i. In case of misfire, check for dirty firing c. Holding round securely replace barrier bag and
mechanism. Clean firing mechanism before replenishing ballistic protective cover. Stow in appropriate rack and
main gun ammunition. use first in subsequent firings.
d. If ammunition is subsequently returned to ASP,
WARNING: Inspect unpacked cartridges which have repack in original packing, including barrier bag.
been dropped for separation of cartridge case from
projectile; separation of base of case from case body; 7-9. Maintenance
open cracks in cartridge case; dented projectiles; and WARNING:
loose windshields (nose caps). Return rejected 1. Do not expose ammunition to extreme
cartridges to ASP for disposition. temperatures. Do not expose to direct sunlight,
flame or other sources of heat. (Non-metallic
j. Strict observance of firing temperature limits is cartridge cases used with this ammunition are
mandatory (para 7-6b). easily ignited by cigarette embers, smoldering
residue, etc.
NOTE. Barrier bags may be difficult to remove at -
250F or below. 2. Handle explosive ammunition with utmost care.
Do not drop, drag, throw, tumble or strike
packaged or unpackaged ammunition.
(Explosive elements in primers and fuzes are
sensitive to shock.)
3. Do not expose ammunition to rain, excessive

humidity or ground moisture. (Otherwise, short
ranges and excessive residue may result.)
Protect electric primer from sources of electricity
to preclude accidental functioning.
7-4. 7
C 10, TM 9-2350-230-12
a. Care. (b) Inspect tank-stowed or other unpacked

ammunition every three months
(1) Ammunition is packed to with stand conditions (preferably during vehicle quarterly
ordinarily encountered in the field. Keep packing maintenance inspection). Conduct as
boxes from becoming broken or damaged. below:
1. Examine barrier bag for nicks, tears,
(2) Since ammunition is impaired by moisture, frost, and loose fit.
extreme temperatures and foreign matter (mud,
oil, etc.), observe the following: 2. Without removing barrier bag,
examine each round. Reject for
(a) Do not break moisture-resistant seal on separation of cartridge case from
container until ammunition is to be used or projectile or separation of base of
stowed in vehicle. case from case body.
(b) Shield ammunition from sources of high 3. Repack rejected rounds (see below,
temperatures (e.g., direct rays of sun). paragraph 7-9_(3)), marking
container to indicate type of
b. Handling. damage. Return rejected rounds to
ASP for disposition. ASP or higher
(1) Cartridge cases are damaged easily; protect echelon may remove bag and
from hard knocks and blows. visually inspect round for disposition
purposes.
(2) Protect cartridge during handling from moisture (c) Protect bagged cartridge cases from
and foreign matter. Do not remove barrier bag exposure to water or oil as follows:
until round is being chambered.
1. Fix oil and water leaks in vehicle
(3) Protect fuzes, primers) and rotating bands at all promptly.
times from foreign matter and impact.
2 Close hatches before hosing down
c. Maintenance. outside of vehicle.
WARNING: Never alter ammunition or components. 3. Take care, when lubricating internal
parts of hull or turret, to prevent oil
(1) Procedures. or grease contamination of either
ammunition or stowage racks.
CAUTION: Do not remove barrier bag during
inspection of unpacked ammunition. (2) Ammunition prepared for firing. But not fired.
(a) Inspect packaged ammunition stored in (a) Return such ammunition to original
dry, cool and well ventilated indoor storage condition and packing.
at least once a year. Inspect packaged
ammunition protected only against direct (b) Include barrier bag and laminated barrier
rain and sunlight (e.g., tarp covered, bag as part of repacking operation.
outdoor storage) at least once a month.
Inspect unpackaged ammunition in (c) Mark appropriately and use first in
storage and outside of packaged subsequent firings in order to keep stocks
ammunition exposed to direct rain or of open packings to a minimum.
sunlight once a day. Open boxes or
containers which show evidence of severe
contamination or deterioration, and inspect
ammunition. Do not open sealed boxes or
containers for inspection purposes only.
7-4.8
C 10, TM 9-2350-230-12
(3) Unserviceable ammunition. c. Provisions.
(a) Conspicuously mark unserviceable - (1) Use heavy, well supported dunnage to keep
ammunition or explosive components bottom tier of stack off ground and to prevent it
UNSERVICEABLE, and return to from sinking into ground.
ammunition supply personnel for
disposition. NOTE. A hard stand of blacktop or gravel and sand
(b) Repackage ammunition in original - is preferable to excessive use of dunnage.
containers. If original container is
unsuitable, use expended packing Allow at least 6 inches of space beneath pile for air
material and transfer all markings. circulation. Dig suitable trenches to prevent water from
Conspicuously mark all layers of packing flowing under pile.
UNSERVICEABLE.
(2) Provide nonflammable or fire resistant covers
7-10. Storage (e.g., tarpaulin) for all ammunition. Maintain an
air space of approximately 18 inches between
WARNING: Avoid exposure of ammunition and cover and ammunition. Keep cover at least 6
ammunition components to direct sunlight. (Ammunition inches from pile on ends and at sides, to permit
exposed directly to sunlight, or in unventilated circulation of air.
containers, inclosures. shelters. freight cars, closed
vehicles and similar structures exposed to direct sunlight, (3) Store ammunition containers with top sides up.
may reach temperatures exceeding upper storage (Labels or markings on boxes and containers
limits.) indicate which side should be up.)
a. Storage Temperature Limits. Except as (4) Minimum distances permitted between given
otherwise specified, observe the following limits; quantities of 152MM rounds and inhabited
buildings, etc., for ammunition in quantity-
Lower limit: -650F. distance class 5 (TP-T and canister) and class 7
Upper limit: +1450F. (HE-T and HEAT-T-MP) are indicated in TM 9-
1300-206.
b. Sites.
Paragraphs 7-11 and 7-12 - deleted.
WARNING: Do not store ammunition under trees or
adjacent to towers or other structures that attract
lightening.
When ammunition must be stored in the open, select a

storage site free of power lines, electric cables and
readily ignitable and flammable materials. Sites should
not be adjacent to reservoirs, water mains or sewer lines.
Sites should be level and well drained.
(7-4. 10 blank)/7-4. 9
C 10, TM 9-2350-230-12
Section 7-3. COMMUNICATIONS EQUIPMENT
7-13. Communications Data d. Radio Set AN/VRC-53. The AN/VRC-53 consists

of receiver- transmitter RT- 505/PRC- 25 and amplifier-
The following tables and illustrations provide data for power supply OA-3633/GRC, and provides short range
communications equipment. Additional information will communication with crew served vehicles and other
be found in TM 11-5820-401-10 and TM 11-5820-498- support elements.
10.
e. Amplifier, Audio Frequency AM-1780/ VRC. The
a. Radio Set AN/VRC-12. The AN/VRC-12 can AM-1780/VRC is used to select the mode of operation, to
monitor two channels simultaneously, or one channel provide connections to an external field telephone, and to
can be monitored while transmitting on the other, and amplify the intercom and radio signals.
has ten (10) preset channels.
f. Universal Communications Harness for AR/AAV,
b. Radio Set AN/VRC-46. The AN/VRC-46 is FT, 152MM, M551. The universal communications
similar to the AN/VRC-12, except that monitoring an harness consists of antennas, adapters, cables, mounts,
additional channel is not possible. Also, the receiver- the AN/VIC-1 (VC), control boxes, and is installed
transmitter is manually tuned; no preset channels are equipment.
available.
g. Controls, Intercommunication Set C-226/V RC,
c. Radio Set AN/VRC-47. The AN/VRC-47 is used C-2297/VRC, and C-2298/VRC. The C-2297/VRC and
in installations where preset channels are not required. C-2298/VRC are used to provide intercom facilities and
Two channels can be monitored simultaneously or one to extend use of the radio set to crew members. The C-
channel can be monitored while transmitting on the other 2296/VRC includes a handset which permits personnel
channel. outside the vehicle to communicate with those inside and
to use the facilities of the radio set.
7-5
C 10, TM 9-2350-230-12
TABLE 7-4. RADIO SETS AN/VRC (BASIC UNITS) AND INTERCOMMUNICATION EQUIPMENT
MAIN ITEMS COMPRISING AN QUANTITY PER RADIOSET

OPERABLE EQUIPMENT 12 46 4 53
Receiver-Transmitter Radio RT-246/VRC (fig. 7-4) 1 0 0 0

Receiver-Radio R-442/VRC (fig. 7-4) 1 0 1 0
Cover CW-649/VRC 1 0 1 0
Receiver-Transmitter, Radio RT-524/VRC 0 1 1 0
Cover CW-653/VRC 1 1 1 1
Amplifier-Power Supply AM-2060/VR 0 0 0 1
Receiver-Transmitter RT-505/PRC-25 0 0 0 1
Universal Communications Harness (1) (1) (1) (1)
Installed Equipment Consisting of:
Mounting Mt - 1029/VRC 1 1 1 1
Mounting Mt - 1089/VRC 1 1 1 1
Amplifier Audio Frequency AM1780/VRC 1 1 1 1
Control C-2296 1 1 1 1
Control C-2297/VRC 1 1 1 1
Control C-2298/VRC 3 3 3 3
Cable Assy R. F. CG-1773/U (4-ft) 1 1 1 1
Cable Assy R. F. CG-1773/U (12-ft) 1 1 1 1
Cable Assy S. P. Elect CX-4722/VRC (5-ft) 1 1 1 1
Cable Assy Power CX-4721/VRC (2 ft 6 in) 1 1 1 1
Cable Marker Kit 1 1 1 1
Mast Base AB-558 (see note) 1 1 1 1
Antenna Matching Unit MX-2799/VRC 1 1 1 1
Base, Antenna Support AB-719/VRC 1 1 1 1
Adapter UG-306B/U 1 1 1 1
Adapter UG-273/U 1 1 1 1
STOWED ITEMS:
Antenna, Element, AT-1095( )/VRC 1 1 1 1
Antenna, Element, AT-1096( )/VRC 1 1 1 1
Mast Section MS-116 2 2 2 2
Antenna Tie Down Kit 2 2 2 2
Bag CX-870 (SC-D-279907) 1 1 1 1
Antenna Sleeve (Commercial Item) 1 1 1 1
Installation Instructions 1 1 1 1
NOTE. All M551 Vehicles are equipped with Universal Communication Harness. Mast Base AB-15/G, FSN 5985-221-
5544 is substituted for Mast Base AB-558/GR when not available.
7-6
TM 9-2350-230-12
A. INTERCOM CONTROLS AND AMPLIFIER UNIT.
B. COMMUNICATIONS TRANSMITTER, RECEIVER, AND MOUNTS.

WE 10899
Figure 7-4. Radio set AN/VRC-12 installed
7-7
TM 9-2350-230-12
A. INTERCOMMUNICATION SET ACCESS DOOR. B. INTERCOMMUNICATIONS SET CONTROL BOX
Figure 7-5. Intercommunication set C-2296/VRC control installed
7-8
CHAPTER 8
ORGANIZATIONAL MAINTENANCE INSTRUCTIONS
Section 8-1. GENERAL
a. Chapters 8, 9, 10, and 11 contain organizational materiel are authorized for issue by tables of allowances
maintenance instructions for hull, power plant and turret (TA) and tables of organization and equipment (TOE).
components. When the nature of repair, modification or
adjustment is beyond the scope of organizational b. An improvised tool (gage) to facilitate control
maintenance, material will be referred to support cable adjustment is illustrated in figure 8-0.
maintenance.
8-5. Painting and Restencilling Vehicle Markings
b. Illustrated maintenance procedures follow one of
three fasic categories: a. Painting Instructions. Preparation of the materiel
for painting, methods of painting, and material to be used
(1) Removal/installation by numerical are contained in TB 746-93-1 and TM 9-213. Instructions
sequence. for camouflage painting are contained in FM 5-20.
(2) Descriptive step-by-step b. Restenciling Vehicle Markings. When required

removal/installation. to insure legibility, restencil in accordance with
instructions contained in table 8-2.
(3) Exploded view with legend for
replacement of unserviceable components 8-6. Application of Adhesives
as required.
a. Clean surfaces to be bonded with toluol cleaner
c. Refer to LO 9-2350-230-12 for organizational (FSN 6810-257-2486). Surface must be free of grease,
lubrication instructions. paint, talc, soapstone or any other foreign substance.
8-2. Preventive Maintenance Services b. Stir adhesives until fluid. Apply an even coat of
These services are performed by organizational adhesive to each mating surface. Let dry to touch. (In
maintenance personnel with the assistance of the vehicle any event, no less than 1/2 hour -24 hours is optimum -
crew. The intervals and items to be checked by temperature and humidity will be a controlling factor in
organizational maintenance personnel are listed under drying time.)
pertinent assembly or component in table 8-17. c. Apply another even coat of adhesive to both
previously coated surfaces. Let dry until tacky (approx.
8-3. Repair Parts 20 min.), but no longer transfers to the finger when
touched lightly.
a. Repair parts, tools, and equipment are available
to the organizational mechanic to perform those d. Press rubber or fabric to metal or other mating
maintenance functions allocated to organizational surface applying pressure by using a roller or other
maintenance personnel. suitable tool to insure full contact between surfaces.
b. Remove preservative material from all spare CAUTION: Do not attempt to pull or pry on either
parts before installing. bonded surface after mating.
8-4. Special and Improvised Tools and Equipment
a. Special tools and equipment will be found in

table 8-1. Standard and commonly used tools and
equipment having general application to this
8-1
TM 9-2350-230-12
TABLE 8-1. SPECIAL TOOLS AND EQUIPMENT
ITEM IDENTIFYING FIG.

NO ITEM NUMBER REF. USE
HULL, SUSPENSION, AND POWER PLANT

1 ADAPTER: brake spline 5120-906-1051 9-39 To adjust vehicle brakes.
(8355955)
2 ADAPTER: torsion bar puller 5120-901-6181 9-62 Used with PULLER 5120-313-
(10954004) 9496 to remove and install
No’s. 2 and 3 torsion bars.
3 FIXTURE: track 4910-906-1053 9-80 Used to disconnect and

(10955739) 9-81 connect track.
4 GAGE: pressure kit 4910-572-8612 8-1 Used to check transmission

(8356176) oil pressure.
5 GAGE: sprocket wear 5210-906-3706 9-72 Used to check sprocket

(10954023) for wear.
6 HANDLE 5120-034-0884 Used with removers and

(10914196) replacers.
7 INSTALLER: bearing cone 4910-906-1064 9-64 Used to install road wheel

(10954367) arm spindle inner bearing
cone.
8 PIN: drift 5120-678-2795 9-80 Used to remove and install

(10861180) 9-81 track pin.
9 PUNCH 5120-910-3738 9-65 Used to remove road wheel

(10954017) housing inner seal.
10 REGULATOR, accumulator 4910-766-3354 9-16 Check or recharge air box

charging accumulator nitrogen
pressure.
11 REMOVER 5120-907-0696 9-63 Used to remove shock ab-

(10954000) 9-74 sorber; with screw removed,
use as torsion bar cover and
anchor cover wrench.
12 REPLACER: bearing 5120-906-1062 9-73 Used with handle 5120-034-

(10954006-1) 0884 to replace sprocket hub
inner bearing cup.
13 REPLACER: bearing cup 5120-906-1063 9-73 Used with handle 5120-034-

outer bearing cup.
14 REPLACER: oil seal 5120-906-1057 9-65 Used with handle 5120-034-

(10954007-1) 9-69 0884 to replace idler hub oil
9-73 seal; road wheel arm support
housing outer oil seal; sprocket
hub outer oil seal.
82
C6, TM 9-2350-230-12
TABLE 8-1. SPECIAL TOOLS AND EQUIPMENT - CONTINUED

HULL, SUSPENSION, AND POWER PLANT - CONTINUED

inner oil seal.

(10954007-3) 0884 to replace road wheel
arm support housing inner
oil seal.

(10954007-4) 0884 to replace road wheel
arm spindle oil seal.
18 REMOVER 5120-999-4055 Used with puller 5120-313-

11604833 9496 to remove road wheel
arm and torsion bar anchor.
18.1 REMOVER ASSY: road 11643803 9-64 Used to remove road wheel
wheel spindle spindle.
19 REMOVER AND REPLACER 5120-906-1058 9-65 Used with handle 5120-034-

(10954003-3) 9-73 0884 to remove sprocket hub
inner bearing cone and oil
seal; replace road wheel arm
support housing inner bearing
(use with thrust collar).

(10954003-2) 9-69 0884 to remove idler hub
inner bearing cone and oil
seal; replace No. 2 and 3
road wheel support housing
outer bearing.

(10954003-1) 0884 to remove road wheel
arm hub outer oil seal and
bearing cone; replace road
wheel arm hub inner bearing
cup.

(10954005) 9-73 0884 to remove sprocket hub
outer oil seal and bearing
cone; replace road wheel
arm hub outer bearing cup.
23 SLING: lifting 4910-907-8990 9-5 Used to remove and install

(10954024) power plant. (May also be
used to remove and install
grille and access cover.)
8-3
C6, TM 9-2350-230-12

HULL, SUSPENSION, AND POWER PLANT - CONTINUED

24 WRENCH: fan pulley 5120-907-0698 9-32 Used to remove and install
(10954016) fan pulley retaining nut.
25 WRENCH: idler hub 5120-901-4282 9-69 Used to remove and install

(10954002-2) idler hub retaining nut.
26 WRENCH: spindle 5120-901-4283 9-76 Used to remove and install

(10954002-1) road wheel arm retaining
nuts.
27 WRENCH: sprocket hub 5120-901-4294 9-73 Used to remove and install

(10954002-3) sprocket hub retaining nut.
SPECIAL EQUIPMENT FOR OPERATING POWER PLANT OUT OF VEHICLE (FIG. 9-10)
KIT: Consisting of 11643870
items 28 through 34
28 ADAPTER: coupling to hose 4730-921-3242 9-10 Four (4) required. Fuel

inlet and return lines.
29 CABLE: ground 4910-084-0789 9-10 One (1) required From

(10913655) power plant-to-vehicle
ground.
30 CABLE: power 5180-245-4280 9-10 One (1) required From

10954635 generator harness-to-vehicle
voltage regulator.
31 CABLE: power 4910-045-4275 9-10 One (1) required From

10954664 power plant harness-to-
vehicle harness.
32 COUPLING: quick disconnect 4730-738-8571 9-10 Two (2) required. Used

(7388571) with hose assembly MS
28741-8-1200.
33 HOSE: fuel 4720-803-7667 9-10 Two (2) required. Fuel

MS 28741-8-1200 inlet and return lines.
34 LEAD: engine starter 2720-059-5777 9-10 One (1) required Main

C-11605661 power cable-power plant
starter-to-battery circuit.
8-4
C10, TM 9-2350-230-12

TURRET ELECTRIC DRIVE, MISSILE, ARMAMENT, AND SIGHTING AND FIRE CONTROL
TOOL KIT, GUN AND 4933-921-7335
TURRET: supplemental, 5910335
organizational main-
tenance
Consisting of:
34. 1 PROD TEST: test-electrical 6625-678-0657 Used with multimeter.

connector 10394564-010
34.2 ADAPTER: socket wrench 5120-227-8088 11-13 Used with wrench assy.
1/2 x 3/4 GGG-W-641 4933-915-8560 to remove/
install firing probe.

34.3 MULTIMETER: 6625-553-0142
35 Deleted. (See ETHYL

ALCOHOL, Sect. B-3
App. II)
36 Deleted - See item 51
37 SOCKET WRENCH ATTACH- 5120-683-8597 11-13 Used to install firing probe

MENT SOCKET HEAD SCREW: cover and guard.
3/16 hex plug end size
38 SOCKET WRENCH ATTACH- 5120-596-8508 10-26 Used with TORQUE WRENCH

MENT SOCKET HEADSCREW: 5120-821-3441 to remove or
1/4 hex plug end size install optical tracker.
39 SOCKET WRENCH ATTACH- 5120-243-1674 10-21 Used with TORQUE WRENCH

MENT-SOCKET HEAD SCREW: 10-22 5120-821-3441 to remove or
5/16 plug end size install optical transmitter.
39.1 SOCKET WRENCH ATTACH- 5120-596-1199

MENT SOCKET HEAD SCREW:
3/8 hex end
39. 2 SOCKET WRENCH ATTACH- 5120-585-6237

MENT SOCKET HEAD SCREW:
1/2" sq dr, 3/8 hex plug end
size
40 PLIERS: slip-joint 5120-624-8065 Removing and installing

electrical harness connec-
tors as required.
40.1 PLIERS: 5120-247-5177 Use as required.
40.2 PLIERS: retaining ring 5120-464-4777 11-10. 2 Used to remove snap ring
(check valve) 11578314 when disassembling check
valve
8-5
C10, TM 9-2350-230-12
TABLE 8-1. SPECIAL TOOLS AND EQUIPMENT

TURRET ELECTRIC DRIVE, MISSILE, ARMAMENT, AND SIGHTING AND FIRE CONTROL-CONT.
40.3 PULLER TOOL: check valve 4933-117-9351 11-10.1 Used to remove check
11578228 valve assembly from gun
tube.
40.4 SCREWDRIVER: jewelers 5120-180-0728 To adjust balance potentio-

meter in accessory box,
amplifier-integrator, and
relay boxes.
40.5 ALIGNMENT TOOL: 5120-227-7291 To adjust balance potentio-

GG-A-450 meter in accessory box,
amplifier -integrator, and
relay boxes.
40.6 SOCKET, SOCKET WRENCH: 5120-261-2823 11-13 Used to remove/install

3/4 drive, 1-5/8 opening firing probe outer nut.
41 TEST SET: electrical drive 4933-909-9356 10-3 Used to check out turret
(11586473) electric drive control
system.
42 Deleted
42.1 SERVICING TOOL, CHECK 4933-464-4776 11-10.2 Used to disassemble and

VALVE: 11578313 11-10. 3 clean check valve.
43 Deleted (See TOLUENE,

Sect. B-3 App. lI)
44 Deleted
45 WRENCH, SPANNER: 5120-915-8572 11-14 To remove and replace

11577226 breech mechanism drive
motor.
46 WRENCH, ASSEMBLY: 4933-915-8560 11-13 To remove and replace

11576797 breech mechanism firing
probe nut.
46.1 WRENCH: check valve plug 4933-111-6734 11-10.1 Used to remove/install

11578063 check valve plug.
47 Deleted
48 WRENCH, TORQUE: 5120-242-3263 As required.

(0 - 350 ft-lb)
49 WRENCH, TORQUE: 5120-821-3441 As required.

(100 - 750 in. -lb)
8-6
C8, TM 9-2350-230-12

50 Deleted
MISCELLANEOUS SPECIAL EQUIPMENT
51 RIVER: hex head (1/8") 5120-596-0934 10-21 Used with TORQUE

10-22 WRENCH 5120-598-6906
to remove or install
optical transmitter.
Figure 8-0. Improvised tool for adjusting land steer control

cables and linkage.
8-6.1
TM 9-2350-230-12
TABLE 8-2. STENCIL LOCATIONS AND SPECIFICATIONS
STENCIL LOCATION
NOTE 1. Stencils maybe one or more lines as space permits,
with 1/4-inch spacing between lines and each letter to be
0.100 thick x 1/2 inch high.
NOTE 2. Paint exterior letters white and interior letters
black (SPEC-TT-E-48).
TURRET EXTERIOR
CAL. .50 AMMO Between Cal. .50 ammunition footmans loops on turret upper
slope plate (6 stencils on left side and 1 on right side).
WATER CAN Between water can footman loops at front of turret ventilating
fan.
NOTE. The following stencils are located on turret rear

upper slope plate and are for O.E.M. equipment which is
carried in turret stowage rack.
BEDROLL Left center portion of rack.
3 BEDROLL Below FIELD PACK stencil.
FIELD PACK Right center portion of stowage rack.
3 FIELD PACK Below BEDROLL stencil.
FLAG SET Below SPARE ANTENNA stencil.
HELMET (4) Evenly spaced across top portion of turret stowage rack.
PAULIN Below SPARE BARREL stencil.
RATIONS Below 3 FIELD PACK stencil.
SPARE BARREL Right of stowage rack center net strap and at lower portion of
slope plate.
SPARE ANTENNA Left of stowage rack center net strap and at lower portion of
slope plate.
TURRET INTERIOR
AMMO 7.62MM Left front on turret floor under ammunition box.
BINOCULARS On front of binoculars bracket which mounts to left side of

commander’s sub-floor.
CANTEEN One on left front leg bracket of commander’s sub-floor.

One on vertical ammunition rack front support.
One on rear side of 7.62-MM ammunition feed box.
FLASHLIGHT Above flashlight holder to right of commander.
GAS MASK One at left front of loader on turret lower slope plate.
One at left front of loader on turret upper slope plate.
8-6.2
TM 9-2350-230-12
TABLE 8-2. STENCIL LOCATIONS AND SPECIFICATIONS - CONTINUED
STENCIL LOCATION
TURRET INTERIOR - Continued
GRENADES One above grenade bag to right of command-
er. One on protective screen frame above
grenade bag to left of loader.
7.62-MM SPARE BARREL On turret roof above loader.
M37 PERISCOPE On bottom of M37 periscope rack which is

mounted to left front of turret roof.
NIGHT VISION DEVICE Above night vision device cover which

mounts to turret upper slope plate - left
front.
ODDMENT BOX One on each door of oddment box located un-

der loader’s seat.
HULL EXTERIOR
AXE Above bracket which secures axe head to en-

gine access cover.
BORE BRUSH Rearward on battery access cover just below

hinged portion of cover.
CLEANING STAFFS Centered between two brackets which secure

cleaning staffs on lower portion of engine
access cover.
CROWBAR Centered between two brackets which secure

crowbar on engine access cover.
MATTOCK Left of strap which secures mattockl on en-

gine access cover.
MATTOCK HANDLE Between two brackets which secure mattock

handle on engine access cover.
RAMMER Forward on battery access cover just below

SHOVEL On bracket which secures shovel blade on

engine access cover.
TOW CABLE To right of strap which secures tow cable

eyes at top center of engine access cover.
8-7
TM 9-2350-230-12
TABLE 8-2. STENCIL LOCATIONS AND SPECIFICATIONS - CONTINUED
STENCIL LOCATION
HULL EXTERIOR - Continued
TRACK FIXTURE Centered on battery access cover just below
HULL INTERIOR
CAL .50 AkLO On torsion bar tunnel at rear center of

driver’s seat.
CANTEEN On bulkhead below canteen bracket, left

rear of driver.
COOK STOVE On bracket which secures stove to bulkhead,

left rear of driver.
GASMASK On hull upper right slope plate, to right

of driver.
7.62-M4 A4MO One on hull floor, right rear of driver in

back of torsion bar tunnel. One on torsion
bar tunnel, right rear of driver’s seat.
PAMPHLET BAG On hull upper right slope plate, to right

of driver.
PERISCOPE AND SPARE On periscope box attached to hull roof,

HEAD right of driver.
RATIONS On torsion bar tunnel at rear center of

driver’s seat.
SUBMACHINE GUN On bracket which secures gun to hull roof,

left rear of driver.
SUBMACHINE GUN AMMO On bracket which secures ammo to hull roof,

left of driver.
8-8
C 13, TM 9-2350-230-12
Section 8-2. TROUBLESHOOTING
NOTE. All references to M55IA1 in this section pertain to vehicles equipped with laser
range finder.
shooting the armament. Question the vehicle crew to

8-7 Scope obtain the maximum number of observed symptoms.
The greater the number of symptoms of trouble that
a. This section contains troubleshooting can be evaluated, the easier will be the isolation of the
information and provides tests for locating and correcting defect.
some of the troubles which may develop in the vehicle,
armament, or sighting and fire control materiel. Each c. Tests and remedies provided in this section are
symptom of trouble or malfunction given for an individual governed by the scope of organizational level of
unit or system is followed by a list of probable causes maintenance.
and corrective actions necessary to remedy the
malfunction. d. Troubleshooting information is listed in table 8-4
which gives the symptoms of troubles usually
b. If a specific trouble, test, or remedy is not encountered, with the necessary corrective action. If the
covered in this manual, proceed to isolate the system in corrective action does not remedy the trouble, notify
which the trouble occurs; then locate the trouble. Do not support maintenance.
neglect the use of any test instruments such as
ohmmeter, voltmeter, ammeter, multimeter, test lamp, e. Refer to table 10-3 for additional information on
hydrometer, or pressure and vacuum gages that are testing, malfunctions, and remedies for the turret electric
available. Standard automotive theories and principles of drive control system.
operation apply in troubleshooting the vehicle. Standard
armament procedures apply in trouble-
(8-8.2 blank)/8-8.1
C4, TM 9-2350-230-12
TABLE 8-2.1. TROUBLEDHOOTING INDEX
TABLE TABLE
COMPONENT REFERENCE COMPONENT REFERENCE
Transmission 8-3; 16, 8-4 Turret Elec. Drive Control 82, 8-4
Engine 1, 8-4 Turret Traverse Mechanism 99, 8-4
Hull Electrical 41, 8-4 Elevating Mechanism 103, 8-4
Generating System 42, 8-4 Conventional Weapons Elect. 110, 8-4
Tracks and Suspension 46, 8-4 Missile Subsystem 115, 8-4
Personnel Heater 51, 8-4 M81 Gun-Launcher 122,8-4
Winterization Kit 60, 8-4 Gun-Launcher Mount 131, 8-4
Bilge Pump 67, 8-4 Sighting & Fire Control 136, 8-4
Turret Elec. Accessories 72, 8-4 Ohmmeter Method of
Commander’s Cupola 78, 8-4 Electrical Troubleshooting 8-5
8-8. Engine Source of leakage must be determined and the condition

corrected to avoid damage to transmission. Notify
a. Starting, fuel, lubrication, coolant, and oil cooling support maintenance.
systems are all regarded as being part of the engine, and
will be treated as such in this manual. Trouble in any one CAUTION: Remove drive shafts (fig. 9-71) when
of these systems will be reflected in engine performance; pressure checking transmission in vehicle.
therefore, corrective action for these troubles is
contained in the engine section of the troubleshooting b. Pressure Check Points. To aid in troubleshooting
table. and testing, a number of plugged openings are provided
for checking operating pressures (fig. 8-1). These plugs
b. When troubleshooting the engine or one of the can be removed for connection of pressure gage 4910-
systems mentioned in a. above, open the power plant 572-8612. Use these pressure test points to locate
exhaust grilles for access to components of the engine abnormal pressures that indicate transmission
or its various systems. malfunctions.
c. During all tests, observe pressure and CAUTION: Stop engine each time before removing
temperature warning lights on driver’s indicator panel. or installing pipe plugs and attaching gage adapter.
Install plug as soon as gage adapter is removed.
d. Check engine oil and water, and transmission oil Remove only the plug necessary to perform the desired
levels before starting the engine. Add if necessary. test.
e. Warm up engine to operating temperature c. The chart in table 8-3 lists normal hydraulic
before conducting tests. pressures under various operating conditions with an
engine speed of 1500 rpm or as specified in table. Small
f. Check engine stall speed (table 8-17, sequence variations in pressure from those given in the chart do
64). not necessarily mean that malfunctions exist.
Malfunctions will cause radical changes in pressure.
8-9. Transmission Table 8-4 will furnish probable causes of any abnormal
test results.
a. Transmission Oil Level. Before making pressure
tests, check transmission oil level and add oil if NOTE. Should any of the pressure or temperature
necessary. The cross drive transmission does not burn warning lights indicate malfunctions, the engine must be
or use oil as an engine does. Consequently, if stopped and the cause determined.
transmission oil level is found to be low at frequent
checking periods, the cause is due to leakage. d. Use of the intercommunication set (fig. 7-5) will
facilitate communication with the driver.
8-9
C9, TM 9-2350-230-12
TABLE 8-3. XGT-250-1A TRANSMISSION PERFORMANCE TESTS (FIG. 8-1)
8-10
C9, TM 9-2350-230-12
WE 666191
Figure 8-1. XTG250-1A transmission oil pressure check points - locational reference
8-11
TM 9-2350-230-12
TABLE 8-4. TROUBLESHOOTING
ENGINE
NOTE. For corrective
action of malfunctions not
listed in this table, refer
to supporting maintenance
personnel.
1.starter will not engage. a.Master switch off. a.Turn master switch "ON".
b. Shift lever not in neutral b. Move shift lever into
position. neutral position.
c. Neutral safety switch not c. The neutral switch may not
functioning properly. be closed properly due to
improper adjustment.
Readjust or replace.
d. Low battery voltage. d. Batteries discharged or
defective. Test and
service, or replace. If
properly charged batteries
are not available, slave
vehicle from external 24-
volt dc power source
(table 2-5).
e. Loose electrical connections e Tighten electrical
and/or ground strap. connections,
f. Defective starter switch, f. If solenoid does not pull in
relay, or solenoid. with audible sound when
supplied with 24 volts,
replace solenoid.
Feel starter relay. If no
solenoid action is de-
tected when supplied with
24 volts, replace.
Test switch electrically,
replace if required.
g. Defective starter motor. If starter does not rotate
when supplied with 24
volts, replace starter.
2. Starter rotates freely Starter pinion not engaging Replace starter.
but engine fails to flywheel.
crank.
3. Engine will not rotate. a. Low battery voltage. a. Replace batteries (fig. 9-97)
or slave vehicle (table
2-5).
8-19
TM 9-2350-230-12
Table 8-3. TROUBLESHOOTING - CONTINUED
ENGINE - Continued
3. Engine will not rotate - b. Internal seizure b. Notify support maintenance.

Continued
4. Low engine crank a. Low battery voltage a. Replace batteries or slave
speed vehicle.
b. Loose or corroded battery b. Clean and tighten battery
cable terminals or elec- cable terminals and
trical connections electrical connections.
c. Incorrect oil viscosity for c. Consult LO 9-2350-230-12
prevailing temperature for proper grade of oil.
5. Engine cranks but fails a. Insufficient fuel a. Check fuel tanks, add fuel
to start if required.
b. Fuel shut-off control is b. Open fuel shut-off.
closed.
c. Fuel shut-off valves on fuel c. Open fuel tank valves.
tanks are closed.
d. Main fuel line disconnected d. Connect fuel line,
e. Fuel injector racks not in e. Refer to support
full fuel position due to maintenance.
defective injector or bind
in control linkage.
f. Defective engine fuel pump f. Replace fuel pump (fig. 9-19).
g. Restriction in air inlet g. Remove restriction.
h. Defective engine air blower h. Notify support maintenance.
drive.
i. Low engine compression i. Exhaust valves, rings, or
gaskets defective. Notify
support maintenance.
j. Air in fuel system j. Check fuel lines for leaks
and tighten.
6. Engine fails to start a. Low engine crank speed a. Engine crank speed should
in low ambient be at least 100 rpm.
temperature.
b. Battery power low b. Replace batteries or slave
vehicle.
c. Improper oil viscosity for c. Refer LO 9-2350-230-12.
prevailing temperature.
8-13
TM 9-2350-230-12
ENGINE - Continued
6. Engine fails to start in d. Air box heater inoperative d. Check accumulator pressure.
low ambient temper- Recharge accumulator
ature - Continued with hand pump if fuel
pressure gage is not in
cold start band.
e. Accumulator defective e. Replace accumulator (fig.
9-15).
f. Hand pump will not develop f. Inspect, repair, or replace
sufficient pressure to pump.
charge accumulator.
g. Damaged high tension lead g. If high tension lead is cut or
damaged, replace.
h. Defective ignition coil h. Replace ignition coil.
i. Improper grade of fuel i. Consult fuel specification
(par. 1-6) for proper
grade of fuel,
j. Improper start procedure j. Consult cold weather start
procedure (fig. 2-14).
Proper starting is a re-
sult of experience and
development of a "feel"
for cold starting.
k. Winterization kit inoperative. k. Consult troubleshooting
procedure for winteriza-
tion kit (later in this
table).
7. Lack of engine power a. Improper control linkage a. Determine full engine and
adjustment, transmission throttle
control lever travel, Ad-
just linkage (fig. 9-44).
b. Insufficient fuel b. Fuel supply low or shut-off
valve closed. Add fuel
or open shut-off valves.
Inspect fuel strainer and

filter for water, foreign
matter, or damage.
Clean, repair, or replace

as required.
Measure fuel return flow

(par. 9-9).
8-14
TM 9-2350-230-12
ENGINE - Continued
7. Lack of engine power - c. Insufficient air c. Check air cleaner indicator
Continued for restriction (fig. 5-1)
and clean or replace
element as required,
Check the turbocharger and

engine blower for foreign
object damage and proper
operation. If defective,
notify support maintenance.
8. Uneven operation, a. Low coolant temperature a. if engine coolant temperature
frequent stallng, or is not between 1600F and
rough idle 210F, troubleshoot
coolant system.
b. Insufficient fuel b. Check fuel return flow
(par. 9-9).
c. Faulty injectors c. Erratic engine operation
may be caused by leaking
fuel injector spray tips.
Notify support mainte-
nance.
d. Governor instability d. Hunting may be caused by
bind in the governor-to-
injector linkage. Notify
Buffer in governor out of

adjustment. Notify
9. Pre-detonation, a. Oil in combustion air stream. a. Check the engine for
blocked air box drains
(fig. 9-13).
Inspect for excessive oil in

the air inlet. Cause may
be due to oil leak at turbo-
charger or blower-to-
block gasket. Notify
b. Faulty injectors b. Notify support maintenance.
8-15
TM 9-2350-230-12
ENGINE - Continued
10. Engine overheats a. Restricted cooling air a. The exterior of the radiator
passages core may be plugged,
restricting normal air
flow. Clean radiator with
air, water, or steam.
b. Low coolant level b. Check coolant level and
fill as required. If
abnormal amount of water
is required to fill the
coolant system, inspect
for loose connections or
source for leakage.
Notify support mainte-
nance if cause is other
than the coolant system.
c. Improper coolant fan c. Check the coolant fan drive
operation belts for proper tension.
Adjust as required.
If fan does not operate with

a coolant temperature of
185°F, lock up clutch
(fig. 5-2) and notify
d. Pressure cap defective d. Replace cap.
e. Thermostat inoperative e. The thermostat may be
defective and not open at
normal operation tem-
perature. Remove and
test in hot water bath
(167-192°F). If defective,
replace.
f Coolant pump drive belt f. Tighten or replace belt
slipping (Fig. 9-36).
g. Coolant pump failure g. Inspect the coolant pump for
damaged impeller. If defective, replace (Fig. 9-36).
h. Malfunction of lubrication h. The oil filter may be
system clogged causing a re-
striction in circulation of
lubricant. Inspect filter.
Check oil level in accor-
dance with LO 9-2350-230-
12. If oil level drops
continually, notify support
maintenance.
8-16
TM 9-2350-230-12
ENGINE - Continued
11. High oil consumption a. External leakage a. Inspect oil filter, hose connec-
tions, and valve cover gasket
for leakage. Tighten or re-
place as required.
b. Internal leakage b. Remove air inlet elbow
and inspect turbocharger
for evidence of oil. Notify
support maintenance
personnel if internal
leakage exists.
c. Breather restriction c. Clean and repair or replace
crankcase breather
assembly (fig. 9-13).
d. High crankcase pressure d. Clean engine breather air
box collector drain and
inspect for restriction.
e. Internal engine damage e. Notify support maintenance.
12. Low oil pressure a. Pressure indicator in- a. Check for loose electrical
operative connections at transmitter
and gage.
Check oil pressure with

positive pressure gage
and replace transmitter
if faulty.
b. Oil quantity may be low b. Fill to proper level in ac-
cordance with LO
9-2350-230-12.
c. Improper oil for prevailing c. Consult LO 9-2350-230-12
temperature for proper grade of oil.
d. Poor oil circulation d. Replace oil filter element
if clogged. A plugged
oil cooler is indicated by
high oil temperature.
13. Black or gray exhaust a. a. Incomplete combustion a. Exhaust back pressure or
smoke restricted air inlet causes
insufficient combustion
air. Locate and clear the
obstruction.
Check for obstruction in

exhaust duct or muffler.
8-17
TM 9-2350-230-12
ENGINE - Continued
13. Black or gray exhaust a. Incomplete combustion - Check turbocharger for
smoke - Continued Continued foreign object damage and
free spin. Notify support
maintenance if turbo-
charger is defective.
Check air inlet for

obstruction.
b. Excessive fuel or irregular b. Notify support maintenance.
fuel distribution.
c. Improper grade of fuel c. Check fuel supply for proper
grade (par. 1-6).
NOTE: Engine exhaust will
tend to be blacker when using
CITE fuel than with standard
grades of fuel.
14. Blue exhaust smoke a. Condensation in fuel a. Drain condensate from
filters Wig. 5-2) and center
fuel tank (fig. 5-3).
b. Low coolant temperature b. Blue smoke should clear up
after coolant temperature
reaches a minimum of
160°F.
c. Lubrication oil not burned c. Internal lubrication oil
in cylinder (blown through leaks present. Consult
cylinder during scavenging high oil consumption
period) (above). Notify support
maintenance.
d. Engine breather drain collector d. Drain (Fig. 5-3).
box needs draining.
15. White exhaust smoke Misfiring cylinders Notify support maintenance.
TRANSMISSION
16. Vehicle will not move a. Shift control linkage dis- a. Inspect and repair or
in any range connected, bent, broken adjust (fig. 9-47).
or out of adjustment.
b. Low transmission oil level b. Consult LO 9-2350-230-12
for proper oil level.
c. Low main oil pressure c. Check for proper main oil
system pressure (ar.
8-9).
8-18
TM 9-2350-230-12
TRANSMISSION - Continued
17. Vehicle will travel in Shift control linkage faulty Inspect and repair or adjust
only one range shift control linkage
regardless of the (fig. 9-47).
range selected.
18. Oil high-temperature a. Temperature indicator faulty. a. Check for loose electrical
warning light comes connections or replace.
on during normal
operation b. Low oil level b. Check oil level on dipstick-
type gage (LO 9-2350-230-
12). Fill as required.
c. High oil level c. Check oil level on dipstick-
type gage (LO 9-2350-230-
12). Drain to proper
level.
d. Brakes improperly adjusted d. Readjust brakes (fig. 9-39).
e. Oil cooler clogged e. Remove and steam-clean oil
cooler.
19. Low lubrication a. Pressure indicator a. Check for loose electrical
pressure warning inoperative connections, or replace
light comes on transmitter if faulty.
during normal
operation b. Low oil level b. Check oil level (LO 9-2350-
230-12).
c. Regulator valve open or c. Notify support maintenance.
faulty.
20. Vehicle will travel in High-range clutch failed Notify support maintenance.
all ranges except
fourth gear.
21. Vehicle will travel in Reverse range clutch failed Notify support maintenance.
all ranges except
reverse.
22. Shift control selector a. Shift control linkage dis- a. Inspect and repair or
will not move connected, bent, broken, adjust (fig. 9-47).
or out of adjustment.
b. Downshift inhibitor faulty b. Notify support maintenance.
c. Selector valve faulty c. Notify support maintenance.
8-19
TM 9-2350-230-12
23. Steer control will not a. Steer control linkage binding, a. Inspect and repair or adjust
move bent, or incorrectly (fig. 9-53).
adjusted.
b. Steer valve faulty b. Notify support maintenance.
24. Converter lockup The lockup clutch failed Notify support maintenance.
clutch will not
release.
25. Convertor lockup Low governor pressure Check piton governor
clutch will not pressure (par. 8-9).
engage Notify support
maintenance.
26. Convertor lockup a. Linkage out of adjustment a. Adjust throttle control
clutch does not linkage (fig. 9-44).
engage and re-
lease at proper b. Low governor pressure b. Check piton governor
speeds pressure (par. 8-9).
If incorrect, notify
27. Brakes are hard to a. Linkage out of adjustment a. Adjust brake linkage
operate and do not (fig. 9-48).
stop vehicle
effectively b. Brake control cable length b. Adjust brake control cable
incorrect (fig. 9-48).
c. Bind on brake apply lever c. Eliminate bind on brake-
apply lever.
d. Brake clutch not adjusted d. Adjust brake clutch (fig.
properly 9-39).
28. Vehicle travels in Low-range clutch failed Notify support maintenance.
first reverse range, (will not release).
first and second
forward range, but
stalls in any other
range. Vehicle
moves in neutral.
29. Vehicle travels in Intermediate-range clutch Notify support maintenance.
third forward failed (will not release).
range and second
reverse, but stalls
in any other range.
Vehicle moves in
neutral.
8-20
TM 9-2350-230-12
30. Vehicle travels in High-range clutch failed Notify support maintenance.
fourth range but (will not release).
stalls in any other
range. Vehicle
moves in neutral.
31. Vehicle travels in a. Right-steer clutch failed a. Notify support maintenance.
first range but
stalls in all other b. Left-steer clutch failed b. Notify support maintenance.
ranges. Vehicle is
free in neutral.
32. Vehicle travels in a. Left-output clutch faulty a. Notify support maintenance.
second, third, and
fourth range, but b. Right-output clutch faulty b. Notify support maintenance.
stalls in first range
and reverse ranges.
Vehicle does not
move in neutral.
33. Vehicle travels in a. Left-reverse-range clutch a. Notify support maintenance.
reverse ranges but faulty.
stalls out in for-
ward ranges. Vehi- b. Right-reverse-range clutch b. Notify support maintenance.
cle does not move faulty.
in neutral.
34. Vehicle has only land Steer relay valve faulty Notify support maintenance.
steer.
35. Vehicle has only Steer relay valve faulty Notify support maintenance.
water steer.
36. Vehicle pulls to left a. Steer clutch faulty a. Notify support maintenance.
or right in first
range. No steer b. Piston seal ring leakage b. Check steer clutch pressure
applied (par. 8-9).
37. Vehicle pulls to left a. Output-clutch seal ring a. Check output clutch pressure
or right in second, leak (par. 8-9).
third and fourth
ranges. No steer b. Output-clutch faulty b. Notify support maintenance.
applied.
38. Vehicle pulls to left a. Reverse-range clutch seal a. Check reverse-range clutch
or right in reverse ring leak pressure (par. 8-9).
range. No steer
applied b. Reverse-range clutch b. Notify support maintenance.
faulty.
8-21
TM 9-2350-230-12
39. Vehicle pulls to right a. Steer linkage out of adjust- a. Adjust steer linkage (fig.
or left in every ment 9-53).
range. No steer
applied b. Improper track adjustment b. Adjust track tension fig.
5-4).
40. Engine races while a. Low main oil pressure a. Check main oil pressure
vehicle moves (par. 8-9).
slowly.
b. Low-range clutch faulty b. Check clutch pressure
(par. 8-9).
c. Intermediate clutch faulty c. Check clutch pressure
(par. 8-9).
d. High-range clutch faulty d, Check clutch pressure
(par. 8-9).
HULL ELECTRICAL SYSTEM
41. No battery power a. Master relay not closed, a. Inspect and tighten any loose
cable connections and/or
ground straps on the bat-
teries and master relay.
(Table 8-6).
The batteries may be dis-

charged. Replace the bat-
teries or slave vehicle and
start engine. If master
relay will not close, check
master switch.
Master relay faulty. Replace.

b. Batteries have low voltage or b. Test and service or replace
are discharged batteries If properly
charged batteries are not
available, slave vehicle
and start engine and re-
charge batteries with vehicle
generating system.
c. Voltage generating system c. Troubleshoot (items 42
faulty. through 43, and table 8-7).
8-22
TM 9-2350-230-12
HULL ELECTRICAL SYSTEM -

Continued
42. Generating system a. Loose cable connectors, or a. Inspect and tighten loose
inoperative (voltage, improper connections cable connectors.
measured at bat-
teries, below 26.0 b. Defective generator-to- b. Check harness continuity and
volts with engine voltage regulator harness resistance (Table 8-7 and
operating and all fig. 9-112.1).
accessories off).
c. Defective generator drive c. Check generator drive com-
belts, pulleys, gear box, or ponents (figs. 9-109, 9-111,
tensioner 9-112).
d. Failsafe circuit in voltage d. See voltage regulator fail safe
regulator locked out, circuit, ( table 8-7).
e. Loss of generator residual e. Polarize generator (fig. 9-111:
magnetism.
f. Regulator faulty f. Check generator (table 8-7).
Replace regulator if no
fault can be found in genera-
tor, cables, or in a through
e above.
g. Generator faulty g. Generator may pass ohmeter
test and still be faulty. If
regulator is known to be
good, replace generator.
42. 1. Voltage measured Voltage regulator out of adjust- Adjust voltage regulator
at batteries is ment (fig. 9-110).
above 26 volts
but not in accord-
ance with table in
figure 9-110 (with
engine running
and all acces-
sories off).
42. 2. Generator "Motors’ a. Engine fuel shutoff out of a. Disconnect battery-to-voltage
engine on shut- adjustment regulator harness. If
down engine continues to run,
problem is in fuel shutoff
NOTE If generator system (fig. 9-23).
drive belts are broken,
generator will motor until b. Voltage regulator faulty b. If engine stops when battery-
battery-to-regulator cir- to-regulator harness is dis-
cuit is opened. This is connected, voltage regulator
normal unless motoring is faulty. Check for fused
resumes when batteries relay in voltage regulator
are reconnected. (Table 8-7). If relay is
fused, check entire vehicle
and correct short circuit
which caused relay to fuse.
8-23
TM 9-2350-230-12
HULL ELECTRICAL SYSTEM -

Continued
43. Battery requires Generator output voltage too Adjust voltage regulator (fig.
excessive amount of high 9-110).
water added.
44. Tachometer Refer to figure 8-13. 1 and
inoperative paragraph 8-9. 1.
45. Speedometer Refer to figure 8-13.1 and
inoperative paragraph 8-9. 1o
45.1 Odometer Refer to figure 8-13.1 and
inoperative paragraph 8-9. 1.
TRACKS AND SUSPENSION
46. Vehicle will not move Broken final drive shaft Check and replace broken
in any transmission parts (fig. 9-71).
shift selector posi-
tion.
47. Vehicle pulls to one a. Unequal track tension a. Adjust track tension (fig.
side 5-4).
b. Worn or distorted track b. Replace worn parts (fig.
drive sprocket or tracks 9-72).
c. Incorrect brake linkage c. Adjust linkage (fig. 9-48).
adjustment.
d. Incorrect brake adjustment d. Adjust brakes (fig. 9-39).
e. Damaged road wheel e. Replace bearings (fig.
bearings 9-64).
48. Vehicle throws track a. Improper driving or opera- a. Review driver’s instructions
tion of vehicle and proper driving meth-
ods. Do not make high
speed turns.
b. Excessively loose or worn b. Adjust track tension (fig.
track 5-4), or replace worn
track (fig. 9-81).
49. Vehicle sags to one a. Torsion bar broken a. Replace torsion bar (fig.
side or rides 9-62).
excessively hard.
b. Track tension incorrect b. Adjust track tension (fig.
5-4).
c. Suspension arm bearing c. Replace suspension arm
faulty housing (figs. 9-65, 66).
d. Defective shock absorbers d. Replace shock absorbers
(fig. 9-74).
8-24
TM 9-2350-230-12
TRACKS AND SUSPENSION -

Continued
49. Vehicle sags to one e. Incorrect installation of e. Install bars and anchors
side or rides torsion bars and anchors correctly (fig. 9-60).
excessively hard -
Continued
50. Excessive noise in a. Worn or seized road wheel a. Immediately after operating
tracks and suspen- or idler wheel hub bear- vehicle, check road wheel
sion during vehicle ings and idler wheel hubs for
operation excessive heat. Inspect
and replace road wheel or
idler wheel hub bearings
as necessary (figs. 9-64
and 9-69).
b. Worn sprockets b. Reverse sprockets or replace
(fig. 9-72).
PERSONNEL HEATER
51. Heater will not start a. Improper starting procedure a. See figure 2-17 for proper
starting procedure.
b. No electrical power b. Check lead #561, control box
lead, and circuit breaker
(table 8-14). Repair or
replace defective compon-
ents.
c. Inlet or exhaust restriction c. Remove obstruction.
d. Insufficient fuel d.
(1) Shutoff valve closed (1) Open valve (fig. 9-132).
(2) Clogged filter in line or (2) Clean or replace filter(s)
pump (fig. 9-133, 134).
(3) No electrical power to (3) With switch in start posi-
pump tion, check voltage at pump
If no power, check control
box start switch and circuit
#563A (table 8-14). Re-
place switch if defective
fig. 9-107). Repair
harness or notify support
maintenance.
(4) Defective pump (4) If pump has power but will
not run, replace pump,(fig.
9-133).
(5) Overheat switch open (5) Check switch (table 8-14).
Replace if defective rig.
9-137).
(6) Defective shutoff solenoid, (6) Check shutoff solenoid
(table 8-14). If solenoid
is defective, replace heater
8-25
TM 9-2350-230-12
PRESONNEL HEATER -
Continued
e. Flame detector switch out of e. Check switch (table 8-14).
adjustment or defective Adjust or replace switch as
necessary (fig. 9-137).
f. Blower motor inoperative.
(1) No electrical power to (1) Check lead #562 (table 8-14’,
motor Repair harness or notify
Support Maintenance.
(2) Defective motor (2) If motor has power but will
not run, replace heater.
Defective igniter or igniter g. Check igniter and resistors
resistor (table 8-14). Replace
igniter if defective (fig.
9-137). If resistor is
defective replace heater.
h. Other causes h. After eliminating causes "a"
through "g", replace heater
52. Heater starts but indi- a. Lamp burned out a. Press to test. Replace lamp
cator light will not If burned out.
come on.
b. Open electrical circuit b. Check circuits #564 and 565
(table 8-14). Repair
harness or notify Support
Maintenance.
c. Flame detector switch out of c. After heater has run 3 to 4
adjustment or defective minutes, check voltage at
P9, fig. 8-11. If no
power, adjust or replace
switch (fig. 9-137).
53. Heater overheats and a. Restriction in air flow a. Remove obstruction from
shuts off inlet and/or outlet.
b. Blower motor defective b. Replace heater.
c. Excessive fuel flow (defect- c. (Usually accompanied by
ive fuel control valve) excessive smoke). Replace
heater.
54.Heater overheats and Same causes as 53 above, Replace overheat switch.
continues to run plug defective overheat Refer to 53 above to
switch correct cause of over-
heating.
8-26
TM 9-2350-230-12
PERSONNEL HEATER -
Continued
55. Heater starts and runs, a. Clogged filter in line or a. Clean or replace filter(s)
but stops after a short pump fig. 9-133, 134).
interval.
(Control box switch in b. Flame detector switch out of b. If indicator lamp goes out
RUN position) adjustment or defective when heater shuts itself off
adjust or replace flame
detector switch (fig. 9-137}
c. Overheat switch out of c. Check voltage at terminal 30,
calibration Fig. 8-11 immediatelyaftex
heater shuts itself off. If
no power and heater is not
overheated replace switch
fig. 9-137).
56.Odor of fuel in ventilating Fuel leak at standpipe Tighten fuel line connections.
air stream.
57.Blower will not stop Flame detector switch defect- Replace switch.
after purge cycle ive.
58.Heat output too low a. HI-LO switch on LO a. Switch to HI.
b. Clogged filter in line or b. Clean or replace filter(s)
pump (fig. 9-133, 134).
c. Defective fuel control valve c. Check valves (table 8-14).
or air valve If defective, replace
heater.
59.Heater smokes exces- a. Fuel accumulation due to sloe a. Check igniter and resistors
sively or "bangs" on starting (defective igniter (table 8-14). Replace
starting or resistor) igniter if defective If
resistor is defective,
replace heater.
b. Excessive fuel flow (defective b. Replace heater.
fuel control valve).
NOTE. If banging is severe
and persists on several
successive starts, or if
smoking condition does not
clear itself after several
minutes of operation,
replace heater.
8-27
TM 9-2350-230-12
WINTERIZATION COOLANT -
HEATER
60. Heater will not start a. Improper starting procedure. a. See table 2-13 for proper
starting procedure.
b. No electrical power b. Check lead #561 and circuit
breaker (table 8-14. 1).
Repair or replace defective
components.
c. Exhaust restriction c. Remove obstruction.
d. Insufficient fuel flow d.
(1) Clogged filter(s) in line or (1) Clean or replace filter(s)
pump (fig. 9-134).
(2) No electrical power to fuel (2) With switch in START
pump position, check voltage at
fuel pump. If no power,
check control box start
switch and circuit #563A
(table 8-14. 1). Replace
switch if defective. Repair
or replace harness as
necessary (fig. 12-9, 10).
(3) Defective fuel pump (3) If pump has power but will
not run, replace pump.
(4) Defective fuel shutoff (4) Check solenoid (table
solenoid 8-14.1). Replace if
defective.
(5) Overheat switch defective (5) Check switch (table 8-14.1)
Replace if defective
e. Flame detector switch out of e. Check switch (table 8-14. 1).
adjustment or defective Adjust or replace as neces-
sary.
f. Defective igniter or igniter f. Check igniter and resistor
resistor (table 8-14.1). Replace
igniter if defective. If
resistor is defective replace
heater.
g. Blower motor inoperative g.
(1) No electrical power to (1) Check lead #562 and blower
motor motor resistor (table
8-14.1). Repair or replace
harness as necessary. If
resistor is defective re-
place heater.
(2) Defective motor (2) If motor has power but will
not run, replace heater.
h. Other causes h. If causes "a" through "g" have,
been eliminated and heater
still does not start, replace
heater.
8-28
TM 9-2350-230-12
HEATER - Continued
61. Heater starts but indi- a. Lamp burned out a. Press to test. Replace If
cator light does not burned out.
come on.
b. Open circuit b. Check circuits #564 and #565
(table 8-14. 1). Repair or
replace harness as neces-
sary (fig. 12-10).
c. Flame detector switch out of c. Hold switch In START positioi
adjustment or defective and operate heater for 3 or
4 minutes. Check voltage
at P9, figure 8-11. 1. If
no power, adjust or re-
place flame detector
switch. (fig. 12-12).
62.Heater overheats and a. Insufficient coolant flow, a.
shuts off (1) No power to coolant (1) Check circuit #585 (table
circulating pump 8-14.1). Repair or re-
place harness as necessary
(2) Coolant pump defective (2) If pump has power but will
not run, replace pump.
(3) Kinked hose (3) Straighten hose.
(4) System air-locked (4) Bleed air from system
(table 12-1, ’Installation").
(5) Improper coolant mixture (5) Drain and fill system with
(frozen or slushy) proper coolant (table 9-2. 1:
b. Excessive fuel flow b. (Usually accompanied by
excessive smoke). Replace
heater.
63.Heater overheats but Same causes as 62 above, Refer to 62 above. Correct
does not shut off plus a defective overheat cause of overheating and
switch replace overheat switch,
or replace heater.
64. Heater starts and runs a. Clogged filter in line or pump, a. Clean or replace filter(s)
but stops after a short (fig. 9-134).
interval (Control box
switch on RUN) b. Overheat switch out of b. Replace switch (fig. 12-12).
calibration.
c. Excessive carbon in burner c. Replace heater.
d. Defective fuel valve d. Replace heater.
8-28.1
TM 9-2350-230-12
HEATER - Continued
65. Heat output too low a. HI-LO switch on LO a. Switch to HI.
b. HI-LO switch defective b. Check switch (table 8-14. 1)
and replace if defective.
c. Defective coolant thermostat. c. Check thermostat (table
8-14. 1) and replace if
defective.
d. Clogged filter in pump or d. Clean or replace filter(s)
line (fig. 9-134).
e. Excessive carbon in burner e. Replace heater.
f. Defective fuel valve f. Replace heater.
66. Heater burns on high Defective diode Check diode (table 8-14. 1).
heat continuously, If defective replace heater.
even when switched to
LO.
66. 1 Heater will not a. Open circuit a. Check circuit #563 (table
operate on high heat 8-14.1). Repair or re-
place harness as necessary
b. Defective coolant thermo- b. Check thermostat (table
stat 8-14. 1). Replace thermo-
stat if defective.
c. Defective restriction thermo- c. Check thermostat (table
stat 8-14.1). If thermostat is
defective, replace heater.
d. Defective restriction solenoid d. Check solenoid (table 8-14.1).
If defective, replaceheater:
e. Defective diode e. Check diode (table 8-14.1).
If defective replace heater.
f. Excessive carbon in heater f. Replace heater.
66. 2. Blower and coolant efective flame detector Replace switch (fig. 12-12).
circulating pump con- switch.
tinue to operate more
than 5 minutes after
heater shuts off.
8-28.2
TM 9-2350-230-12
HEATER - Continued
66. 3. Excessive smoke, Fuel accumulation due to slom
or "bangs" on starting.
starting (1) Defective igniter (1) Check igniter (table
8-14. 1), and replace if
defective (fig. 12-12).
(2) Defective restriction (2) Check solenoid and valve
solenoid or air valve (table 8-14. 1). If defec-
tive, replace heater.
(3) Defective fuel valve (3) Replace heater.
NOTE. If banging is severe and

persists on several succes-
sive starts, or if smoking
condition does not clear itself
after several minutes of
operation, replace heater.
66.4 BLOWER MOTORS WILL (1) INSUFFICIENT OIL PRESSURE (1) CHECK OIL LEVEL
NOT OPERATE TO ACTUATE OIL PRESSURE (LO 9-2350-230-12)
SWITCH.
(2) REPLACE.
(2) OIL PRESSURE SWITCH
DEFECTIVE (3) INSPECT CIRCUITS 58, 58A,
581 AND HARNESS 11665313
(3) WIRING DISCONNECTED, OR PROPER CONNECTION,
WORN OR SHORT CIR- VOLTAGE AND CONTINUITY.
CUITED.
(4) REPLACE.
(4) OPEN CIRCUIT BREAKER.
(5) REPLACE.
(5) DEFECTIVE RELAY.
(6) REPLACE.
(6) DEFECTIVE BLOWER MOTORS
66.5 BLOWER MOTORS BLOWER OR OUTLET INSPECT AND CLEAN.
OPERATE BUT AIR FLOW HOSE CLOGGED.
RESTRICTED.
NOTE. ALL OTHER MAL-

FUNCTIONS NOT LISTED,
REPORT IMMEDIATELY TO
DIRECT SUPPORT.
(8-28. 4 blank)/8-28. 3
TM 9-2350-230-12
BILGE PUMP SYSTEM

67. Front bilge pump does a. Loose electrical connection a. Inspect and tighten con-
not operate when nections as required.
switch and indicator
light is on b. Open or defective circuit b. If circuit breaker does not
breaker reset in three minutes,
replace (fig. 9-100).
c. Defective relay c. Replace relay (fig. 9-108).
d. Defective bilge pump d. Replace bilge pump (figs.
9-130, 131).
68. Front bilge pump does a. Master switch off a. Turn master switch on.
not operate when
switch is on, indi- b. Loose electrical connections, b. Inspect and tighten or replace
cator light off defective switch or circuit components as necessary.
breaker.
c. Defective switch c. Replace switch (fig. 9-103).
69. Both rear bilge pumps a. Loose electrical connections. a. Inspect and tighten connec-
do not operate when tions as required.
switch and indicator
light is on b. Defective relay b. Replace relay (fig. 9-108).
c. Circuit breakers open or c. If circuit breakers do not
defective reset in three minutes,
70. Both rear bilge pumps a. Master switch off a. Turn on master switch.
do not operate when
switch is on, indi- b. Loose electrical connections. b. Inspect and tighten electri-
cator light off cal connections, as
required.
a. Defective switch c. Replace switch (fig. 9-103).
71. Only one rear bilge a. Loose electrical connections. a. Inspect and tighten connec-
pump operates tions to inoperative pump
and associated circuit
breaker.
b. Circuit breaker open or b. If circuit breaker does not
defective reset in three minutes,
c. Defective bilge pump c. Replace bilge pump (figs. 9-
129, 130).
8-29
TM 9-2350-230-12
TURRET ELECTRICAL SYSTEM

ACCESSORY SYSTEM
72. Ventilating fan does a. Master switch off a Turn master switch ON.
not operate when
switch is on b. Loose wiring b. Inspect and tighten electrt-
cal connections as
required.
c. Ventilating fan switch c. Replace fan (fig. 10-35).
defective.
d. Defective fan motor d. Replace fan.
73. Fan motor vibrates Worn bearings Replace ventilating fan.
excessively.
74. Insufficient circula- a. Obstructed fan intake a. Clean intake.
tion of air in vehi-
cle when fan is on b. Low input voltage b. Check cable terminals for
corrosion and loose con-
nections. Clean and
tighten. Check battery
voltage.
c. Fan slipping or damaged c. Replace fan (fig. 10-35).
75. Dome light or lights a. Master switch off a. Turn master switch ON.
inoperative.
b. Faulty wiring circuit from b. Notify support maintenance.
dome lights to accessory
box or contact ring.
c. Lamps burned out c. Check and replace defective
lamps (fig. 9-96).
d. Faulty switch or switches d. Check and replace dome
in dome lights lights witches if defective
(figs. 9-95 and 9-96).
76. Air filter unit in- a. Loose or defective electri- a. Tighten or repair lead
operative cal lead (fig. 10-30).
b. Defective rheostat b. Notify support maintenance.
c. Purifier motor overheating c. Replace precleaner and
or defective housing. Refer to TM 3-
4240-236-20P.
8-30
TM 9-2350-230-12
TURRET ELECTRICAL SYSTEM

ACCESSORY SYSTEM - Continued
77 Lack of air at a Hose disconnect- a Connect or re-
gas-particulate ed or damaged place hose.
filter unit face
piece b Particulate fil- b Replace filter
ter clogged (fig 10-31).
78 Split hatch a Doors not a Notify support
doors will not aligned maintenance.
close properly.
b Defective or b Replace seals.
loose seals.
c Defective lock c Notify support
and catch assem- maintenance.
blies.
79 Cupola leaks a Defective a Replace seals.
hatch seals.
b Vision blocks b Replace sealer
not sealed (fig 10-49).
properly.
80 Cupola will not a Master switch a Turn master
traverse or erratic off switch ON.
in power mode.
b. Defective brush b. Notify support
assemblies in maintenance.
electrical con-
tact ring.
c Defective c Replace control
switches in box (fig 10-33 and
control box 10-34).
d Damaged wiring d Notify support
harnesses maintenance.
e Foreign material e Clean race ring.
in race ring.
8-31
TM 9-2350-230-12
COMMANDER’S CUPOLA -
Continued
80 Cupola will not f Damaged race f Notify support
traverse or erratic ring maintenance.
in power mode -
continued g Traverse mecha- g Notify support
nism motor de- maintenance.
fective.
81 Cupola will not a Defective trav- a Notify support
traverse manually erse mechanism - maintenance.
b Defective cupola b Notify support
race ring maintenance.
COMMANDER’S CUPOLA - M551A1 ONLY
81.1 Readout 9995 Commander’s cupola Notify support main-

appears at RANGE contact brush tenance to inspect,
(METERS) and 1 assemblies or clean, and adjust
appears at RETURNS electrical contact contact brush
at commander’s dis- rings are worn, assemblies.
play when cupola is dirty, or out of
traversed electri- adjustment.
cally.
81.2 Cupola drive Magnetic switch not Notify support main-
mechanism makes disengaged tenance to check
loud noise when clutch electrical
ROTATION switch is circuit.
actuated.
81.3 Cupola mag- Cal .50 machine gun Check/replace cable
netic clutch acti- direction cable is and/or traverse
vates when CUPOLA/ severed or has a switch assembly
LASER switch is grounded wire (fig 10-49.2.1).
turned on.
81.4 Cupola tra- Cal .50 machine gun Check/replace cable
verses immediately direction cable and/or traverse
when CUPOLA/LASER is severed or has switch assembly
switch is turned a grounded wire (fig 10-49.2.1).
on.
8-32
TM 9-2350-230-12
M551A1 ONLY - Continued
81.5 Cupola mag- Inoperative speed Notify support main-
netic clutch en- switch in drive tenance.
gages too soon, not motor.
letting drive motor
slow down.
81.6 Cupola drive Motor oil seals Notify support main-
motor burns up leaking tenance to replace
drive motor.
81.7 CUPOLA ALIGN Bad contact in Inspect electrical
switch inoperative electrical con- connectors for
nector or defec- bent or broken
tive wiring pins, loose con-
harness nections, dirt or
moisture in con-
nectors, or damage
to wiring harness.
Notify support
maintenance.
81.8 Cupola drive Defective relay Replace resistor box
motor runs at slow in resistor box assembly (fig 10-
speed only 35.4).
81.9 Cupola stops Defective resistor Replace resistor box
before reaching in resistor box assembly (fig 10-
front position dur- 35.4).
ing automatic align
cycle.
81.10 Automatic Defective relay Replace cupola (re-
align cycle stops in cupola (relay) lay) control box
when align switch control box (fig 10-33).
is released.
81.11 Automatic a Defective align/ a Replace cupola/
cupola align func- stop switch in laser control box
tion does not work cupola laser assembly (fig 10-
control box 35.2).
b Defective diode b Replace cupola
in cupola (relay) (relay) control
control box box (fig 10-33).
8-32.1
TM 9-2350-230-12
81.11 Automatic c Defective or c Notify support
cupola align func- - maladjusted limit maintenance to
tion does not work - switch in cupola check cupola re-
continued resolver align- solver alignment
ment mechanism mechanism limit
switches.
81.12 Cupola con- Defective relay in Replace cupola/laser
tinues to oscillate cupola/laser control box assem-
after returning to control box bly (fig 10-35.2).
front position dur-
ing the automatic
align cycle.
TURRET ELECTRIC DRIVE CONTROL
82 Power light and a No electrical a Check operation
ready light do not power to turret of missile sub-
light after lamps system; if no oper-
have been checked ation, replace con-
tact ring. If
missile subsystem
operates, proceed
to step b.
b Defective con- b Replace accessory
ponent in acces- box (fig 10-4) If
sory box malfunction still
occurs, notify
83 Power light Defective component Replace accessory box.
illuminates but in accessory box If malfunction still
ready light does occurs, notify sup-
not illuminate port maintenance.
84 Ready light Defective component Replace accessory
illuminates but in accessory box box.
earlier or later
than timer toler-
ance (18-22 sec-
onds) .
8-32.2
TM 9-2350-230-12
TURRENT ELECTRIC DRIVE

CONTROL - Continued
85 With power and a Defective con- a Operate other
ready lights illu- trol handle control handle If
minated, squeezing it operates, replace
palm switch does defective control
not activate system handle (fig 10-7).
If it does not oper-
ate, proceed to
step b.
b Defective corn- b Replace accessory
ponent in acces- box.
sory box.
86 Motor-generator Defective motor- Replace motor-gener-
does not come up generator ator (fig 10-6).
to speed.
87 With power and a Turret traverse a Release turret
ready lights illu- - lock engaged lock (fig 10-36).
minated, palm switch
depressed, and b Low voltage b Check vehicle
motor-generator power.
operating, control
handle does not NOTE Do not
drive gun and/or operate system on
turret battery power only.
(8-32.4 blank)/8-32.3
TM 9-2350-230-12
TURRENT ELECTRIC
CONTROL - Continued
87. With power and ready c. Defective elevating or c. Attempt to operate turret
lights illuminated, traversing mechanism and weapon manually with
palm switch de- clutch or clutch brush palm switch depressed.
pressed, and mo- If turret or weapon moves,
tor-generator replace clutch brush
operating, control (fig. 10-10).
handle does not
drive gun and/or d. Defective control handle d. Operate switch and/or both
turret - Continued control handles. Replace
handle if defective (fig.
10-7).
e. System malfunction e. Perform test set procedures
(table 10-3).
88. Two second drop-out a. Defective component in a. Replace accessory box
delay inoperative accessory box (fig. 10-4).
when palm switch
released.
88. 1 Palm switch Dirt collected under heel Depress palm switch and
energized without of palm switch remove dirt with thin
being depressed bladed tool.
89. Excessive dead space a. Traversing and/or elevating a. Perform test set procedures
in control handle systems incorrectly ad- (table 10-3).
when traversing justed, or control handle
and/or elevating defective.
b. Free mechanical motion in b. Replace handle (fig. 10-7).
control handles.
90. Gun-launcher elevates a. Poor electrical connection a. Check and tighten connec-
or depresses but tions.
speed erratic.
b. Defective control handle b. Check operation with other
control handle. Replace
defective handle.
c. Defective servo motor c. Replace servo motor (fig.
10-11).
91. Turret traverses but a. Poor electrical connection a. Check and tighten connec-
speed erratic tions.
b. Defective control handle b. Check operation with other
control handle. Replace
handle if defective (fig.
10-7).
c. Defective servo motor c. Replace servo motor (fig.
10-11).
8-33
TM 9-2350-230-12
TURRENT ELECTRIC
CONTROL - Continued
92. Gun-launcher drives a. Poor electrical connection a. Check and tighten connec-
against elevation or tions.
depression stops b. Elevation or depression b. Notify support maintenance.
limit switches incorrectly
adjusted.
93. No override when Defective override function Perform test set procedure
commander’s palm (table 10-3).
switch is depressed.
94. Excessive drift System out of balance Perform test set procedure
(creep) in traverse (table 10-3).
and/or elevation.
95. STAB light does not No gyro feedback, Perform test set procedure
illuminate (table 10-3).
NOTE. Light does

not light in Missile
mode.
96. In STAB mode, gun/ Amplifiers out of balance Perform test set procedure
turret has exces- and balance amplifiers
sive overshoot (table 10-3).
under control of
control handle.
97. Traverse and/or a. Excessive load due to a. Remove obstruction.
elevation servo obstruction.
motor ovetor or b. Replace servo motor (fig.
during operation fan.-
98. Motor-generator a. Dirty screens restrict air a. Clean exterior of screens.
overheats during flow If contamination is inside,
operation replace motor-generator
(fig. 10-6).
b. Defective servo motor b. Replace servo motor (fig.
10-11).
TURRET TRAVERSING
MECHANISM
99. Excessive effort a. Contaminated lubricant on a. Notify support maintenance.
required to man- turret race ring.
ually traverse b. Obstruction (internal or b. Locate and remove obstruc-
turret external) tion.
c. Defective manual drive c. Notify support maintenance.
mechanism.
d. Defective traversing d. Notify support maintenance.
mechanism.
8-34
TM 9-2350-230-12
TURRENT TRAVERSING
MECHANISM - Continued
100. Traversing servo a. Defective internal fan in a. Notify support maintenance.
motor overheats traversing servo motor.
during electric
operation b. Excessive load b. Remove obstructions to
operation.
101. Traversing Damaged gear or bearing Notify support maintenance.
mechanism noisy.
102. Turret does not Defective manual drive Notify support maintenance.
traverse when mechanism.
rotating manual
control handle.
ELEVATING MECHANISM
103. Operation sluggish a. Gun or gun shield internal a. Remove obstruction.
or erratic in man- or external obstruction.
ual or power mode.
b. Worn servo motor brushes b. Inspect brushes and re-
or defective servo motor place if worn or replace
motor if defective (figs.
10-10, 11).
c. Damaged or improperly c. Notify support maintenance.
installed mechanism.
d. Defective magnetic clutch d. Replace brush (fig. 10-10).
brush.
e. Defective gun trunnion e. Notify support maintenance.
bearings.
104. Manual handwheel a. Sheared spring pin in a. Notify support maintenance.
turns freely, but handwheel shaft.
mechanism is
inoperative b. Defective reverse lock b. Notify support maintenance.
(No-Back) clutch or
magnetic clutch.
105. Noisy operation Incorrect shimming or Notify support maintenance.
defective gears and
bearings.
106. Failure to operate a. Servo motor brushes worn a. Replace brushes or motor
in power mode or motor defective (figs. 10-10, 11).
8-35
TM 9-2350-230-12
106. Failure to operate b. Defective magnetic clutch b. Replace brush (fig. 10-10).
in power mode - brush or magnetic clutch If magnetic clutch does
Continued not operate, notify support
maintenance.
c. Malfunction in electric drive c. Troubleshoot drive control
control system system (above).
107. Excessive effort re- a. Obstruction (internal or a. Locate and remove
quired to manually external) obstruction.
elevate or depress
gun-launcher b. Defective manual drive b. Notify support maintenance.
mechanism.
c. Contaminated lubricant on c. Lubricate as prescribed
elevating mechanism in LO 9-2350-230-12.
pivots.
108. Elevating servo Defective internal fan in Notify support maintenance.
motor overheats elevating servo motor.
during electric
operation.
109. Elevating mech- Damaged gear or bearing Notify support maintenance.
anism noisy.
CONVENTIONAL WEAPONS
ELECTRICAL SYSTEM
110. READY lights fail a. READY lamps defective a. Push lamp to test and
to illuminate replace if defective.
b. Loader’s control box b. Transfer switch to READY
switch not in READY position.
position.
c. Fire control selector c. Place switch in CONV or
switch in OFF position MISSILE.
d. Transmitter cover door not d. Open transmitter cover
open when in MISSILE door.
mode.
e. Loose harness connectors e. Tighten all connectors at
relay box, loader’s
control box, gun-
launcher, accessory box,
and safe-to-fire indicator
switch.
8-36
C 1, TM 9-2350-230-12
TABLE 8-4. TROUBLESHOOTING - CONTINUED
CONVENTIONAL WEAPONS
ELECTRICAL SYSTEM -
Continued
110. READY lights fail f. Gun-launcher out of battery. f. Operate hand pump to bring
to illuminate - gun-launcher into battery.
Continued Then check safe-to-fire
indicator to ensure correct
recoil cylinder pressure
(fig. 3-2).
g. Recoil mechanism pressure g. Bleed off pressure until
too high safe-to-fire indicator
switch plunger is in
proper position (fig. 3-2).
111. Gun-launcher mis- Firing probe electrical Tighten electrical connector.
fires with CONV or connector loose.
MISSILE ready
lights illuminated.
112. M73 coaxial machine a. Fire control switch not in a. Place switch in COAX
gun fails to fire COAX position position.
b. Harness connectors loose b. Tighten connector on
machine gun and con-
nector J5 on relay box
(fig. 10-14).
113. Gun-launcher breech a. Loader’s control box SAFE- a. Place switch in SAFE
fails to open or READY switch not in position.
close electrically SAFE position.
b. Fire control selector switch b. Place switch in CONV or
in OFF position MISSILE position.
c. Harness connectors loose c. Tighten all connectors on
gun-launcher, relay box,
loader’s control box,
accessory box, and turret
and weapon control
selector.
114. Telescope reticle a. Fire control selector a. Place switch in CONV or
dimmer box con- switch in OFF position MISSILE position.
ventional or missile
reticle fails to b. Defective lamp b. Replace lamp.
illuminate.
8-37
C8, TM 9-2350-230-12
MISSILE SUBSYSTEM
115. PRIME POWER lamp a. Incorrect prime power a. If vehicle engine is off, start
glows engine. Set idle speed to
750 RPM. Check vehicle
circuit breaker.
NOTE. Prime power on
W1P2 pins A and B.
b. Power supply defective b. Replace power supply. If
PRIME POWER lamp con-
tinues to glow, request
supporting maintenance.
116. POWER SUPPLY lamp a. Modulator defective a. Disconnect W1P3 and W2P2
glows from the modulator. If
POWER SUPPLY lamp
goes out, replace
modulator. Reconnect
cables.
b. Rate sensor defective b. Disconnect W9P1 from rate
sensor. If POWER
SUPPLY lamp goes out,
replace rate sensor.
Reconnect cable.
c. Tracker or tracker mount c. Disconnect W6P2 from
defective tracker. If POWER
SUPPLY lamp goes out,
replace tracker. Recon-
nect cable. If POWER
SUPPLY lamp continues to
glow, disconnect W6P5
from tracker mount. If
light goes out, replace
tracker mount. Reconnect
cable.
d. Power supply defective d. Replace power supply. If
POWER SUPPLY lamp
does not go off, replace
signal data converter.
Repeat test. If problem
is not corrected, replace
test checkout panel. Re-
peat test.
e. Cables defective e. Request supporting main-
tenance.
8-38
C8, TM 9-2350-230-12
MISSILE SUBSYSTEM -
Continued
117 Lamp and meter test) a. No power to test checkout a. Check cable connections.
Lamps do not light, panel Refer table 4-1, step B61.
and meter does not
deflect on test b. Test checkout panel defective. b. Replace test checkout panel.
checkout panel If problem is not corrected,
request supporting main-
tenance.
118. (Lamp and meter test.) a. Cable not properly connected. a. Check cable connections.
Meter needle does Refer table 4-1, step B61.
not deflect to meter
test band. (But b. Defective test checkout panel. b. Replace test checkout panel
lamps glow) and repeat test.
119. (Lamp and meter test), a. Defective lamps a. Replace defective lamps.
Meter deflects pro- Refer table 5-6.
perly but all lamps
do not glow b. Defective test checkout panel. b. Replace test checkout panel.
Repeat test.
120. (Lamp and meter test) a. Defective lamps a. Replace defective lamps.
Meter illumination
lamps do not glow. b. Test checkout panel defective. b. Replace test checkout panel.
Repeat test.
120. 1. (Test checkout Defective test checkout panel Replace test checkout panel.
panel). Dimmer Repeat test.
control does not
affect intensity of NOTE. Dimmer control
the lamps should not affect red indicator
lamps.
120. 1.1. (Transmitter test) a. Transmitter defective a. Replace transmitter. Repeat
Switch does not test.
remain in the on
(up) position for CAUTION: Transmitter
a period of at switch should not remain on
least 15 seconds longer than 1 minute.
NOTE. Whenever trans-

mitter is replaced, perform
transmitter alignment test
(figs. 10-20, 10-20.1), and
request supporting mainten-
ance to perform transmitter
beam pattern test.
8-38.1
C8, TM 9-2350-230-12
MISSILE SUBSYSTEM -
Continued
120. 1.1. (Transmitter test b. Modulator defective b. Replace modulator. Repeat
switch does not test.
remain in the or
(up) position for c. Test checkout panel defective. c. Replace test checkout panel.
a period of at Repeat test.
least 15 seconds
- Continued d. Power supply defective d. Replace power supply.
Repeat test.
e. Signal data converter e. Replace signal data converter.
defective Repeat test. If problem
is not corrected, request
120. 2. (Tracker alignment a. Signal data converter a. Remove cable W6P5 from
test) Align lever defective tracker mount. If align
will not remain in lever will now remain in
the right (up) the right (up) position,
position replace signal data con-
verter. Repeat test.
b. Tracker mount defective b. Replace tracker mount.
Repeat test. If problem is
not corrected, request
120. 3. (Tracker alignment Test checkout panel defective Replace test checkout panel.
test) TRACKER Repeat test.
ALIGN switch on
test checkout
panel will not
remain in the on
(up) position.
120. 4. (Tracker alignment a. Error lever not in the left a. Move error lever to the left
test) cannot null (down) position (down) position.
meter using AZ
or EL adjustment NOTE. Verify that align
screws, located lever is in the right (up) posi-
on telescope tion.
mount.
b. Checksight source lamp b. Look into the telescope.
defective Verify that checksight
source spot-of-light is
visible. If not visible,
replace checksight source
lamp.
NOTE. Check to insure
that telescope filter lever is
in the clear position. ’Temp-
orarily cover or shade teles-
cope opening outside turret to
make spot-of-light more visible.
8-38.2
C8, TM 9-2350-230-12
MISSILE SUBSYSTEM -
Continued
120. 4. (Tracker alignment Look into telescope. Tf
test) cannot null checksight source spot-of-
meter using AZ or light is not sharply defined
EL adjustment or larger than normal,
screws, located on there is moisture in teles-
telescope mount. - cope or telescope mount.
Continued
Look into telescope from
outside turret to verify
that the align prism is
visible and in proper posi-
tion.
c. Tracker or power supply c. Listen for tracker motor. If

defective operating, listen for rate
sensor.
Rate sensor gyros opera-

ting; tracker motor not
operating. Replace
tracker. Repeat test.
Rate sensor gvros and

tracker motor not opera-
ting. Replace power
supply. Repeat test.
NOTE. With excessive

noise in turret, rate sensor
gyros and tracker motor may
be difficult to hear.
d. Signal data converter d. Replace signal data converter
defective Repeat test.
e. Test checkout panel defective. e. Replace test checkout panel.

Repeat test.
f. Telescope mount defective f. Place EL or AZ adjustment
screws (on telescope
mount) at mid range, then
adjust the other screw for
a null on the meter. The
AZ or EL switch on test
checkout panel must be in
correct position.
8-38.3
C8, TM 9-2350-230-12
MISSILE SUBSYSTEM -
Continued
120.4. (Tracker alignment NOTE. The EL and AZ
test) cannot null adjustment may be so far out
meter using AZ or of alignment that checksight
EL adjustment source may not be seen by
screws, located on tracker. It is possible to
telescope mount. - observe the checksight source
Continued in telescope and bring it near
center enough to get a meter
indication.
If meter still will not null,

replace telescope mount;
repeat test. If problem is
not corrected, request sup-
porting maintenance.
120. 5. Align lever does a. Fuse on telescope mount a. Replace fuse on telescope
not reset when defective mount. Repeat test.
RESET switch on
test checkout panel b. Test checkout panel defective. b. Replace test checkout panel.
is activated Repeat test.
c. Signal data converter c. Replace signal data converter
d. Telescope mount defective d. Replace telescope mount.
Repeat test. If problem is
120. 6. (System self- test) Test checkout panel Replace test checkout panel.
SYSTEM TEST defective Repeat test. If problem is
switch will not not corrected, request
remain on (up) supporting maintenance.
120. 7. (System self-test) a. Test checkout panel defective. a. Replace test checkout panel.
CHECKOUT Repeat test.
PANEL lamp glows
after initiation of b. Signal data converter b. Replace signal data converter
system test defective Repeat test. If problem
120. 8. (System self-test) a. Align lever not in right (up) a. Place align lever in right (up)
TRACKER lamp position position. Repeat test.
glows at comple-
tion of test b. Tracker not properly aligned. b. Perform tracker alignment.
Refer table 2-12. Repeat
test.
8-38.4
C8. TM 9-2350-230-12
MISSILE SUBSYSTEM -
Continued
120. 8. (System self-test) c. Tracker motor does not c. Listen for tracker motor
TRACKER lamp run in system self-test during system self-test,
glows at comple- if tracker motor is not
tion of test. - running. (See NOTE)
Continued
NOTE. If tracker motor
runs in tracker align but not
in system s elf-test, probable
cause may be signal data con
verter or tes t checkout panel
Replace tracker. Per-

form tracker alignment.
Refer table 2-12. Re-
peat test.
If tracker does not start,

replace signal data con-
verter. Repeat test.
d. Tracker defective d. Replace tracker. Perform
tracker alignment. Refer
table 2-12. Repeat test.
e. Signal data converter e. Replace signal data con-
defective verter. Repeat test. If
problem is no t corrected,
tenance.
120. 9. (System self-test) a. Error lever not in right (up) a. Place error lever in right
SIG DATA CONV position (up) position. Repeat test
glows at com-
pletion of test b. Tracker not properly b. Perform tracker alignment.
aligned Refer table 2-12.
NOTE. After performing
tracker align, reference the
missile reticle (observe on
telescope) one mil circle on
checksight source. With
align lever right (up) and
error lever left (down) place
error lever right(up) and
observe checksight source
move out of the one mil
circle of missile reticle.
The checksight source
should position itself approx.-
imately two mils northeast
from center of missile
reticle.
8-38.5
C8, TM 9-2350-230-12
MISSILE SUBSYSTEM -
Continued
120. 9. (System self-test c. Tracker defective c. Replace tracker. Perform
SIG DATA CONV tracker alignment. Refer
glows at com- table 2-12. Repeat test.
pletion of test. -
Continued d. Signal data converter d. Replace signal data converter,
defective Repeat test. If problem is
120. 10. (System self-test a. Modulator defective a. Replace modulator. Repeat
MOD lamp glows test.
at completion of
test b. Transmitter defective b. Replace transmitter. Repeat
test. If problem is not
corrected, request sup-
porting maintenance.

(figs. 10-20, 10-20. 1), and
beam pattern test.
120. 11. (System self-test a. Transmitter defective a. Replace transmitter. Repeat

XMTR lamp test.
glows at comple-
tion of test NOTE. Before replacing
transmitter, perform trans-
mitter test. If transmitter
switch on test checkout panel
will not remain on (up) for
15 seconds, replace trans-
mitter. If switch remains on
(up) for 15 seconds, replace
modulator.
CAUTION: Transmitter
switch should not remain on
longer than one minute

(figs. 10-20, 10-20. 1), and
beam pattern test.
8-38.6
C8, TM 9-2350-230-12
TABLE 84. TROUBLESHOOTING - CONTINUED
MISSILE SUBSYSTEM -
Continued
120. 11. (System self-test b. Modulator defective b. Replace modulator. Repeat
XMTR lamp test. If problem is not
glows at comple- corrected, request sup-
tion of test. - porting maintenance.
Continued
120.12. ( System self-test) a. Vehicle input circuit defec- a. Disconnect cable 7J2 from the
TRACKER and tive test checkout panel and
SIG. DATA repeat system self-test.
CONV lamps Refer table 2-12. If SIG
glow at comple- DATA CONV and TRACKER
tion of test lamps do not glow, the
trouble is in the vehicle
input circuit (relay box,
etc. ).
b. In battery limit switch out of b. Adjust or replace in battery
adjustment or defective limit switch. Refer
figure 11-12. Repeat test.
If problem is not corrected
tenance.
120. 13. (System self-test) a. Transmitter door not open a. Check that transmitter door
Gunner’s ready lever is pushed in and
lamp does not locked.
light.
b. Transmitter door switch b. Check switch for proper
defective out of adjustment operation. Adjust or
replace (figure 10-21,
10-22).
c. Breech not fully closed c. Open and reclose breech to
close breech limit switch.
d. Gun launcher not in battery d. In battery limit switch out of
adjustment. Adjust or
replace. Refer figure 11-2
e. Recoil mechanism not correct e. Increase or decrease pres-
pressure sure as required (see fig.
3-2).
f. Loader’s safe/ready switch in f. Check switch position and
safe position or is defective place in ready position.
g. Fire control selector switch g. Put fire control switch in
not in missile position missile position.
NOTE. Gunner’s and
loader’s ready lamps also
lights in conventional position
on selector switch.
8-38.7
C8, TM 9-2350-230-12
MISSILE SUBSYSTEM -
Continued
120. 13. 1. Gunner’s ready Transmitter door switch out of
Check switch for proper opera-
lamp glows adjustment or defective tion. Adjust or replace.
with trans- Refer figures 10-21 and 10-22
mitter door
closed.
120. 14. Null meter a. Rate sensor defective a. Replace rate sensor if:
needle does not
deflect when (1) Audible hum is not heard
turret is moved from rate sensor and
in azimuth or
elevation (2) Rate sensor is not warm
to touch.
b. Test checkout panel b. Replace test checkout panel.
c. Defective gyro selector c. Replace gyro selector.
d. Defective 4A6K2 relay d. Replace board 4A6.
121. (System self-test a. All firing conditions not a. Check table 3-4.1 to assure
verification) present that "conditions prior to
Tracker motor firing" are present.
does not run when
fire trigger is pulled b. No fire pulse to test checkout b. Disconnect cable from test
panel checkout panel 7J2 and
monitor on the cable plug
between pins "C" (POS)
"G" (GROUND) for the
fire pulse, as fire trigger
is pulled. If fire pulse is
not present, check for
loose cable connectors at
relay box, loader’s control
box, gun launcher, acces-
sory box.
c. Test checkout panel c. If fire pulse is present at
defective (7J2) test checkout panel
and tracker does not run,
replace test checkout panel,
Repeat test. If problem
8-38.8
C6, TM 9-2350-230-12
MISSILE SUBSYSTEM
Continued
121.1. Tracker lamp fails a. Defective signal data con- a. Replace the signal data con-
to glow when the ALIGN verter verter.
and ERROR levers are
in the fully left position b. Defective test checkout panel. b. Replace the test checkout
and the system test panel.
switch is in the up posi-
tion.
121. 2. Sig data conv lamp a. Defective signal data con- a. Replace the signal data con-
fails to glow when the verter verter.
ALIGN lever is posi-
tioned fully right and b. Defective test checkout panel. b. Replace the test checkout
the ERROR lever is panel.
fully left with the
system test switch in
the up position.
121. 3. Test checkout panel a. Defective test checkout panel. a. Replace the test checkout
fails to reset; ALIGN panel.
lever fails to move
fully left; tracker b. Vehicle firing circuit b. Notify support maintenance.
motor fails to stop defective.
running within 3
seconds after the fire c. Defective tracker mount c. Notify support maintenance.
trigger is pulled and
ALIGN lever is fully
right and system test
switch is in the up
position.
M81/El GUN-LAUNCHER
122. Insufficient current a. Firing probe assembly front a. Clean contact with fine steel
available at firing contact corroded and/or wool or replace firing
probe to fire defective probe if cracked or
weapon defective (fig. 11-13).
b. Firing probe contact assem- b. Make adjustment and per-

bly not adjusted properly form continuity check
(table 11-2).
c. Open or grounded firing c. Check continuity between
circuit in electrical plug at firing probe (P107,
wiring harness circuits a and b) and large
input power receptacle
(P102, circuits a and p)
respectively. Replace
harness if defective.
(See caution note below. )
8-39
C12, TM 9-2350-230-12
M81/EI GUN-LAUNCHER-
Continued
122. Insufficient current d. Defective 120 v power supply. d. Replace 120v power supply
available at firing (fig. 10-16. 1).
probe to fire weapon-
Continued e. IN battery limit switch e. Replace IN battery limit
defective switch.
f. Recoil mechanism safe-to- f. Notify support maintenance.
fire switch defective.
g. Defective firing circuit relay g. Replace relay box (ig.
box 10-14).
CAUTION: A short circuit in firing probe or harness may damage K-1 relay in loader’s
control box. Notify support maintenance if malfunction still occurs.
123. Breech mechanism a. Defective handcrank assem- a. Notify support maintenance.

fails to open or bly.
close manually.
b. Seized breech chamber and/ b. Notify support maintenance.
or breech mechanism.
124. Breech mechanism a. Breech drive solenoid a. Replace spring, plunger,
binds in manual plunger jammed in locked or solenoid, if damaged.
operation power position.
b. Dirt or foreign material b. Clean breech chamber and
on breech chamber exposed surface of
surfaces and/or spindle spindle assembly and
assembly apply light coating of
lubricating oil
MIL-L-46150
125. Breech mechanism a. Defective electrical wiring (FSN 9150-949-0323)
fails to operate harness.
electrically a. Check continuity between
electric drive motor
plug (P101), solenoid
plug (P103), and limit
switch plugs (P105 and
P106) with large input
power receptacle. Re-
place harness if defective
b. Defective electric drive (fig. 11-12).
motor.
b. Replace motor (fig. 11-14).
8-40
C12, TM 9-2350-230-12
GUN-LAUNCHER- Cont
125. Breech mechanism c. If closed and will not open, c. Replace, if defective
fails to operate breech-open limit switch (fig 11-12).
electrically - LS4 (right side) is defective.
Continued d. If open and will not close, d. Replace, if defective
breech-closed limit switch (fig 11-12).
LS2 (left side) is defective.
e. Seized breech chamber and/ e. Notify support maintenance.
or breech mechanisn.
126. Motor runs but Defective breech drive solenoid Inspect plunger for sheared
breech fails to plunger or plunger bushing teeth; bushing to be certain
operate plunger slides freely. Inspect
solenoid for operation. Re-
place defective components.
127. Breech mechanism a. Insufficient voltage at power a. Use fully charged batteries
sluggish in electri- source or start vehicle engine
cal operation (1000-1100 rpm) to assure
adequate operating voltage
b. Dirt or foreign material on b. Clean breech chamber and
breech chamber surfaces exposed surface of spindle
and/or spindle assembly assembly. Apply light coat-
ing of lubricating oil
c. Clogged porous vent plug in MIL-L-46150
carrier cover (NSN 9150-00-949-0323)
d. Breech mechanism binding c. Remove vent plug and clean
- (fig 11-25)
127. Smoke and/or Failure of seal; erosion or d. Notify support maintenance
flame discharging corrosion of detent assembly
from tube lock key or cannon detent hole Type 1 detent (para 3-3. 4)
or detent assembly Remove/install - fig 11-22
vent Inspect and repair - fig 11-23
Type II detent (para 3-3. 4)
Remove/install - fig 11-23.1
Disassemble/assemble -
11-23.2
Inspect and repair - fig
11-23.3
For removal and inspection of
Type III detent assembly, notify
128. Ammunition detent a. Detent release lever set- supporting maintenance
does not function screw out of adjustment
b. Tip of detent worn or broken a Adjust detent release lever
setscrews (fig 11-23, 23.3)
c. Worn or defective actuating b. Replace detent (fig 11-22,
mechanism 23. 1)
c. Inspect for smooth operation .
d. Detent restricted by defec- Replace worn or defective
tive gas seal in breech components
coupling (MB1 Mod only) d. Replace seal (fig 11-22)
8-41
C14, TM 9-2350-230-12
GUN-LAUNCHER-
Continued
128. Ammunition detent does e. Detent release plunger on e. Disassemble loading tray
not function - continued loading tray seized in detent and free up plunger travel
release position in mounting bracket
(fig. 11-22).
129. Missile cap ejector a. Ejector not cocked a. Adjust ejector cocking
mechanism does not op- bracket setscrew (fig. 11-21).
erate trigger lever in b. Ejector trigger lever set- b. Adjust ejector trigger lever
eject (down) position - screw out of adjustment setscrew (fig. 11-21).
c. Ejector (finger) not posi- c. Adjust position (fig. 11-20).
tioned correctly.
d. Worn or defective parts in d. Disassemble loading tray
loading tray and ejector and ejector group and re-
group place worn or defective
parts.
130. Gases accumulate in a. Defective scavenging system. a. Repair if within scope of or-
turret after firing ganizational maintenance.
Otherwise notify support
maintenance.
b. Defective gun tube obtura- b. Replace (fig. 11-24).
tor gasket.
c. Defective ammunition detent c. Notify support maintenance.
seals d. Remove, clean and in-
d. Defective check valve: indi- -spect. If erosion is evident
cated by over-pressure red on valve, seal, or sealing
stem extending beyond outer surface of tube, notify
surface support maintenance.
CAUTION: Avoid damaging air cylinders, which are under very high pressure.
130. 1. Smoke and fumes a. Erosion on breechblock at a. Notify support maintenance.

discharging from cover rear face of seal
of breech from erosion b. Erosion on firing mechanism. b. Replace firing mechanism.
past firing mechanism.
GUN-LAUNCHER MOUNT
131. Gun-launcher hangs out Defective spring washer set Notify support maintenance.
of battery.
132. Rapid loss of precharge a. Defective hydraulic bleed a. Bleed off all pressure and
pressure in recoil mech- valve or leak in bleed tube or - replace check valve, tube,
anism fitting or fitting (fig. 11-7, 8).
b. Defective check valve in b. Bleed off all pressure and
pump-to-recoil mechanism replace check valve or
tube or defective hand pump hand pump (fig. 11-5).
allowing hydraulic fluid to
be by-passed to reservoir.
8-42
C 10, TM 9-2350-230-12
GUN-LAUNCHER MOUNT -
Continued
133. Difficult to adjust Defective hand pump Bleed off all pressure and
precharge pressure replace hand pump (fig. 11-5).
in recoil
mechanism.
134. Gun-launcher recoils a. Insufficient fluid in recoil a. Notify support maintenance.
with excessive mechanism due to defec-
force tive safe-to-fire indicator.
b. Air in recoil mechanism b. Open bleed valve and bleed
off all pressure, and then
readjust recoil mechanism
pressure (fig. 3-2).
135. Gun-launcher returns Insufficient fluid in or Fill buffer (fig. 5-9)

to battery with defective buffer or replace (fig. 11-2).
excessive force.
INSTRUMENTS
PERISCOPE XM44 SERIES
136. Loss of boresight a. Head assembly not properly a. Remove head assembly
seated and reinstall (fig. 11-41).
b. Body assembly not seated b. Remove body assembly

properly and check for foreign
matter around locating
keys and keyways and
for burred or broken
locating keys.
c. Boresight knobs not fully c. Check knobs to insure firm

engaged engagement with clutch
teeth.
137. Flickering image at a. Reticle lamp Or rheostat a. Replace lamp. Refer to

screen of image failure support maintenance to
intensifier tube replace rheostat.
after stabilization
period b. Loose or poor electrical b. Check and tighten electrical
connection connections.
137.1. Inability to focus Image intensifier tube with Notify support maintenance.
related parts improperly
assembled/installed.
138. Gun and periscope Link assembly loose Synchronize and tighten link
not synchronized adjustment (Fig. 11-43).
8-43
C 10, TM 9-2350-230-12
SIGHTING AND FIRE-CONTROL

INSTRUMENTS-CONTINUED
PERISCOPE XM44 SERIES-
CONTINUED
138. 1. Condensation or Moisture in head and/or body Purge, leak test, and
fogging, XM44E due to loss of nitrogen pressurize (TM 750-116).
Series only pressure.
NOTE. For any malfunctions not listed, notify support maintenance.
TELESCOPE, ARTICULATED, M119 OR M127
MOUNT, TELESCOPE M149
INDICATOR, AZIMUTH 10954720
NOTE. For any malfunction of telescope, telescope mount, or azimuth indicator, notify support maintenance.
QUADRANT (ELEVATION) M13A1C
139. Elevation micrometer a. Worm plunger too tight a. Replace quadrant (fig. 11-39).
and knob will not
turn b. Elevating worm bent b. Replace quadrant.
140. Index travels beyond Stops out of mounting groove Replace quadrant.
scale limits.
141. Excessive backlash. a. Worn gears a. Replace quadrant
b. Loose or worn plunger b. Replace quadrant.
c. Broken spring c. Replace quadrant.
142. Depression and ele- a. Poorly spaced worm or a. Replace quadrant.
vation errors worm gear teeth.
143. Level bubble out of Bubble improperly adjusted Replace quadrant.
adjustment.
PERISCOPES M47 AND M48
144. Poor visibility a. Condensation a. Refer to TM 750-116.
b. Dirty prisms b. Clean.
145. Wiper blades smear Worn wiper blade Replace blade Rig. 11-42)
prisms.
8-44
TM 9-2350-230-12
SIGHTING AND FIRE-CONTROL

INSTRUMENTS - CONTINUED
PERISCOPE M47 AND M48
146. Wiper motor does a. Defective switch a. Replace switch (fig. 9-101).
not operate.
b. Faulty wiring or connections. b. Repair or replace faulty
components.
147. No cleaning fluid a. No fluid in reservoir a. Refill reservoir (fig. 11-37).
from washer
assembly b. Faulty pump b. Replace pump.
c. Clogged tubing c. Clean tubing or nozzle.
d. Clogged check valve d. Clean check valve.
e. Loose tubing connection or e. Replace defective tubing
leaking tubing or connectors.
148. Periscope loose a. Faulty catches a. Notify support maintenance.
after installation.
b. Loose mount assembly b. Tighten bolts (fig. 11-36).
c. Worn seal c. Replace seal (fig. 11-36).
149. No infrared vision Improper electrical ground Clean all mating ground
surfaces between mount,
hatch, body and head.
TABLE 8-5. OHMMETER METHOD OF ELECTRICAL TROUBLESHOOTING
a. General. The ohmmeter method of electrical the meter. All electrical circuits have some resistance.
troubleshooting (fig. 8-2) uses continuity tests to Resistances may be so low, or’ high, they cannot be read
determine whether circuit or device being tested has a with an ordinary ohmmeter. An ohmmeter with a full-
continuous electrical path through cables and unit scale reading of 10 ohms is desirable for measuring low
connected between two test points. An ohmmeter resistances. Higher range ohmmeters are better suited
indicates, on a calibrated scale, resistance of circuit for testing insulation leaks. If the normal resistance of
being tested and is equipped with a power source circuit to be tested is known, select an ohmmeter with a
(battery or hand generator), usually installed inside case full-scale range higher than normal resistance.
which houses
8-45
C4, TM 9-2350-230-12
TABLE 8-5. OHMMETER METHOD OF ELECTRICAL TROUBLESHOOTING - CONTINUED
CAUTION Never attempt to make ohmmeter tests e. Test Point Designation. Ohmmeter test points are
until all sources of power connected to equipment to tabulated for each electrical circuit and referenced to an
be tested are disconnected. The ohmmeter will be accompanying illustration. The letter "P" denotes
damaged if this procedure is not followed. testpoint (terminal, plug, or receptacle) and is followed by
a number designating the test point numerical
b. Continuity Tests. Place prods or clips from sequence. Multi-plug and receptacle designation are
ohmmeter on end points of circuit to be tested, or to two also followed by a letter to indicate the specific pin or
terminals at which ends of component to be tested socket. P1-A then will denote test point "1," pin "A."
terminate. If a normal reading is obtained, circuit has no Ground (gnd) means any part of vehicle that has a good
breaks or openings. electrical connection with the unit being tested. Electrical
circuits and tables are as follows:
c. Resistance Reading. A resistance reading is taken Figure 8-3. Troubleshooting Master Relay and Battery
to determine electrical condition of a coil, resistor, Power Circuits
capacitor, or complete circuit. When correct resistance of Figure 8-4. Troubleshooting Generator and Voltage
a unit is known, a resistance test will indicate if there is a Regulator Circuits
fault in circuit. Figure 8-5. Troubleshooting Engine Starter Circuit
Figure 8-6. Troubleshooting Flame Heater Circuits
d. Infinity and Zero Ohmmeter Readings. Figure 8-7. Troubleshooting Indicator Panel Circuits
Figure 8-8. Troubleshooting Fuel Level Indicator
(1) Infinity reading. An. infinity reading indicates that Circuits
no path exists for current flow in a component, or that an Figure 8-9. Troubleshooting Driver’s Periscope Wiper
open circuit exists. The ohmmeter indicator does not Circuits
move when infinite resistance exists but remains at a Figure 8-10. Troubleshooting Bilge Pump Circuits
point on ohmmeter scale usually marked by symbol "oo" Figure 8-11. Troubleshooting Personnel Heater
or abbreviation INF" An ohmmeter should always give an Circuits
infinity reading when test leads are disconnected. Figure 8-12. Troubleshooting Power Plant Indicator
and Warning Light Circuits
(2) Zero reading. A zero ohmmeter reading indicates Figure 8-13. Troubleshooting Vehicle Driving Light
closed circuit with no measurable resistance. When a Circuits.
known resistance is specified and a zero reading is
obtained, a short circuit exists within component or circuit Figure 8-13.1. Tachometer/Speedometer/ Odometer
being tested. An ohmmeter should always be adjusted to f. Generator Regulator Performance Test.
give a zero reading when test prods or clips are touched
together. Refer to Figure 8-4.
8-46
C9, TM 9-2350-230-12
Figure 8-2. Troubleshooting hull and power plant electrical system with multimeter
8-47
C9, TM 9-2350-230-12
Figure 8-3. Troubleshooting-master relay and battery power circuits
8-48
C8. TM 9-2350-230-12
TABLE 8-6. MASTER RELAY AND BATTERY POWER CIRCUITS (FIG. 8-3)
8-49
TM 9-2350-230-12
TABLE 8-6. MASTER RELAY AND BATTERY POWER CIRCUITS-CONTINUED
8-50
C9, TM 9-2350-230-12
Figure 8-4. Troubleshooting-generator and voltage regulator circuits
8-50.2 (8-50. 1 Blank)

C8, TM 9-2350-230-12
TABLE 8-7. GENERATOR AND VOLTAGE REGULATOR CIRCUITS (FIG. 8-4)
8-51
C9, TM 9-2350-230-12
Figure 8-5. Troubleshooting-engine starter circuit
8-52
TM 9-2350-230-12
TABLE 8-8. ENGINE STARTER CIRCUITS (FIG. 8-5)
8-53
C9, TM 9-2350-230-12
WE 66624
Figure 8-6. Troubleshooting-flame heater circuits
8-54
TM 9-2350-230-12
TABLE 8-9. FLAME HEATER CIRCUITS (FIG. 8-6)
8-55
C9, TM 9-2350-230-12
Figure 8-7. Troubleshooting-indicator panel light circuits
8-56
TM 9-2350-230-12
TABLE 8-10. INDICATOR PANEL LIGHT CIRCUITS (FIG. 8-7)
8-57
C9, TM 9-2350-230-12
Figure 8-8. Troubleshooting - fuel level indicator circuits
8-58
C4, TM 9-2350-230-12
TABLE 8-11. FUEL LEVEL INDICATOR CIRCUITS (FIG. 8-8)
CAUTION: Disconnect battery positive and negative cables before making tests.
NOTE. Tanks must have at least 36 gallons of total fuel for purposes of these tests. Upper tank valves
must be open.
CIRCUIT TEST POINTS RESISTANCE
COMPONENT NUMBER FROM TO (ohms) CIRCUIT REMARKS
Power circuit 31C P6 P5J 0 Through circuit Infinity indicates open

to panel breaker to panel circuit breaker or
defective lead.
Power circuit to 32C P5F P1 0 Panel to lower Infinity indicates open
transmitters transmitter circuit, defective lead
or blown fuse.
Power circuit in --- P11J P11F 0 Through jumper in Resistance indicates
panel panel defective panel.
Fuel level --- P11E P9 350 Through indicator to Infinity indicates open
indicator ground circuit in panel.
Fuel level --- P11E P11F 350 Through indicator to Infinity indicates open
indicator ground circuit in panel.
Mounting bracket --- PANEL HULL 0 Mount ground lead Infinity indicates open
ground lead.
Upper trans- 32A P4 P5E 0 Upper transmitter to Infinity indicates open
mitter to panel indicator panel circuit or defective lead.
lead
Lower trans- --- P1 P2 45 Through lower Zero resistance
mitter transmitter indicates lost float.
Upper trans- --- P3 P10 385 Through upper Low resistance indi-
mitter transmitter cates shorted trans-
mitter resistor. Infinity
indicates open resistor.
Upper Trans- -- (a) P3 P4 5-385 Through part of Resistance varies from
mitter transmitter resistor zero OHMS at empty to
385 OHMS at full. Zero
OHMS indicates lost
float.
-- (b) P4 P10 0-385 Balance of resistor Total resistance,(a) +
(b) should equal
approx-
imately 385 OHMS.
Low
total resistance indi-
cates shorted resistor.
Transmitter 30 P10 HULL 0 Through circuit Resistance indicates
ground circuit groun #30 to ground poor ground connection
d
to bulkhead. Infinity
indicates open ground
circuit.
Transmitter 32B P2 P3 0 Lower transmitter to Infinity indicates open
interconnector upper transmitter circuit or defective lead.
TEMPORARILY DISCONNECT LEAD #32B AT P3. THEN:
Transmitters --- P1 P10 Infinity Through lower trans- Reading other than
mitter resistor to infinity indicates lower
ground, transmitter resistor is
shorted.
8-59
C9, TM 9-2350-230-12
Figure 8-9. Troubleshooting - driver’s periscope wiper circuits
8-60
TM 9-2350-230-12
TABLE 8-12. DRIVER’S PERISCOPE WIPER CIRCUITS (FIG. 8-9)

CAUTION: Disconnect battery positive and negative cables before making resistance or continuity tests.
Windshield wiper 31A P1 P2-C 0 Circuit through cir- Infinity indicates open
switch feed cuit breaker to circuit or defective
panel lead.
Windshield wiper 521L P2-C GND 170-210 Circuit through Infinity indicates switch
indicator light switch and light open or defective lead.
bulb bulb Close switch to get indi-
cated resistance. Zero
OHMS with switch
closed indicates short
circuit.
Windshield wiper P2-C P3-B 0 OR INF Circuit through switch Infinity indicates switch
switch and panel "off". Zero OHMS indi-
cates switch "on". Any
in-between resistance
indicates defective
switch.
Windshield wiper 521 P3-B P8-P9 0 Circuit from panel to Infinity indicates open
lead wiper motor feed circuit or defective
lead.
Windshield wiper 521B P4 P5-P6 0 Circuit from circuit Infinity indicates open
parking circuit P7 breaker to wiper circuit or defective
lead motor feed lead.
Windshield wiper 50 P11- GND 0 Circuit from wiper Infinity indicates open
motor grounding P12 motor to ground circuit or defective
circuit P13 lead.
I R. periscope 57 P15 P14 0 Circuit through Infinity indicates open
feed lead circuit breaker to circuit or defective
LR. periscope con- lead.
nection.
8-61
C9, TM 9-2350-230-12
Figure 8-10. Troubleshooting-bilge pump circuits
8-62
TM 9-2350-230-12
TABLE 8-13. BILGE PUMP CIRCUITS (FIG. 8-10)

Main bilge sys- 111 P1 P2-C 0 Circuit from master Infinity indicates open
tem electrical 111 P1 P2-D 0 relay to the switch circuit or defective
feed 723 P1 P4-B 0 panel and both bilge lead.
722 P1 P5-B 0 pump relays
Front bilge 721 P2-D P3-E 0 OR INF Circuit through Front bilge pump
pump switch switch and panel switch "on":
Infinity indicates open
circuit, defective
leads or switch.
Front bilge pump
switch "off": Zero
OHMS indicates de-
fective switch or
short circuit.
Front bilge 721L P2-D GND 170-210 Circuit through Front bilge pump
pump indicator switch panel and switch "on":
light light bulb Infinity indicates open
circuit, defective leads
or burned out light
bulb. Zero OHMS in-
dicates a short circuit.
Front bilge 721- P3-E P4-A 0 Circuit from switch Infinity indicates open
pump panel to 721A panel to relay circuit or defective
relay lead lead.
Front bilge 723A P4-C P6 0 Circuit from relay Infinity indicates open
pump relay to through circuit circuit, defective lead
pump lead breaker to pump or circuit breaker.
Front bilge pump 723B P6 GND 35-. 70 Circuit through pump Resistance variation
greater than .70 OHMS
or less than .35 OHMS
indicates defective
pump.
Rear bilge pump 721B P2-C P2-B 0 OR INF Circuit through Rear bilge pump switch
switch switch and panel "on": Infinity indicates
open circuit, defective
leads or switch.
Rear bilge pump switch
"off": Zero OHMS in-
dicates defective switch
or short circuit.
Rear bilge pump 721BL P2-B GND 170-210 Circuit through Rear bilge pump switch
indicator light switch panel and "off": Infinity indicates
light bulb open circuit, defective
leads or burned out
bulb. Zero OHMS in-
dicates a short circuit.
Rear bilge pump 721B P2-B P5-A 0 Circuit from switch Infinity indicates open
panel to relay panel to relay circuit or defective
lead lead.
8-63
C4, TM 9-2350-230-12
TABLE 8-13. BILGE PUMP CIRCUITS (FIG. 8-10) - CONTINUED

Rear bilge pump 722A P5-C P7 0 Circuit from relay Infinity indicates open
relay to left 722B through circuit circuit, defective lead
Rear bilge pump 722A P5-C P8 0 Circuit from relay Infinity indicates open
relay to right 722C through circuit circuit, defective lead
Left rear bilge 722B P7 GND .35-.70 Circuit through pump Resistance variation
pump greater than. 70 OHMS
or less than . 35 OHMS
indicates defective
pump
Right rear bilge 722C P8 GND .35-. 70 Circuit through pump Resistance variation
pump greater than .70 OHMS
or less than. 35 OHMS
indicates defective
pump.
TABLE 8-14. PERSONNEL HEATER CIRCUITS (FIG. 8-11)

Disconnect power lead at P1, and use voltmeter to check voltage from battery at 1.
Leave connector P1 disconnected during all ohmeter tests.
WIRING
Power supply 561 P1 P2D O Through lead and

circuit breaker
Harness 563 P2B P3B O Through lead

562 P2C P3C O Through lead
565 P2E P3E O Through lead
564 P2D P3D O Through lead Resistance indicates
560 P3A GRD O External grd. circuit defective circuit.
563A P2A P4 O Through lead to fuel
pump
--- P3A Case O Internal grd. circuit
CONTROLS
Start-Off-Run P2D P2A INF
Switch (OFF) P2D P2C INF
Start-Off-Run P2D P2A O Any other reading
Switch (START) P2D P2C O indicates defective switch
Start -Off -Run P2A P2E O
Switch (RUN)
(Leave Start-Off-Run Switch in RUN):
Hi-Lo Switch(L(O P2B P2E INF Any other reading
indicates
defective switch
HI-Lo Switch (HI) P2B P2E O
8-64
C4, TM9-2350-230-12
Figure 8-11. (Superseded) Troubleshooting - personnel heater circuits
8-65
C4, TM 9-2350-230-12
TABLE 8-14. PERSONNEL HEATER CIRCUITS (FIGURE 8-11) - CONTINUED

HEATER
Igniter Igniter Grd Approx. 0. 5 Through igniter Zero or high reading in-
term Strap dicates defective igniter.
Flame Detector P5 P6 O Any other reading indi-
Switch (Cold P5 P7 O Through switch cates switch out of adjust.
position only) P8 P9 INF ment or defective.
Overheat Switch Term. 9 Term O Through switch INF indicates defective
30 switch
Resistor "A" Across resistor Approx. 0.4 Through resistor INF indicates open
(Blower Resistor: terminals resistor
Resistor "B" Across resistor Approx. 0. 6 Through resistor INF indicates open
(Igniter Resistor) terminals resistor
Resistor "C" Across resistor Approx. 1.0 Through resistor INF indicates open
(Igniter Resistor) terminals resistor
Shutoff Solenoid Lead#30 Case Approx. 140 Through solenoid to High or low reading in-
Disconnected grd dicates defective solenoid
from overheat
switch
Restriction Solen- P3B Case Approx. 70 Through solenoids in High or low reading indi-
oid and Air Valve parallel to grd cates one or the other
Solenoid . solenoid is defective
TABLE 8-14.1. WINTERIZATION KIT COOLANT HEATER CIRCUITS (FIGURE 8-11.1)

Disconnect power lead at P1, and use voltmeter to check power supply from battery at P1.
Leave connector P1 disconnected during all ohmeter tests.
WIRING
Power Supply 561 P1 P2D O Through lead and
circuit breaker
Harness 564 P2D P3D O Through lead
565 P2E P3E O Through Lead
565 P3E P10 O Through lead to
coolant pump
562 P2C P3C O Through lead Resistance indicates
563 P2B P3B O Through lead defective circuit
563A P2A P4 0 Through lead to
fuel pump
8-66
C4, TM 9-2350-230-12
Figure 8-11.1. (Added) Troubleshooting - winterization kit coolant heater circuits
8-66.1
C4, TM 9-2350-230-12
TABLE 8-14.1 WINTERIZATION KIT COOLANT HEATER CIRCUITS (FIG. 8-11.1) - CONTINUED
8-66.2
C4, TM-9-2350-230-12
8-66.3
(8-66.4 Blank)
C9, TM 9-2350-230-12
Figure 8-12. Troubleshooting-power plant indicator and warning light circuits
8-67
TM 9-2350-230-12
TABLE 8-15. POWER PLANT INDICATOR AND WARNING LIGHT CIRCUITS (FIG 8-12)
8-68
TM 9-2350-230-12
TABLE 8-15. POWER PLANT INDICATOR AND WARNING LIGHT CIRCUITS (FIG 8-12) - CONTINUED
8-69
C9, TM 9-2350-230-12
Figure 8-13. Troubleshooting-vehicle driving light circuits
8-70
TM 9-2350-2t0-l2
TABLE 8-16. VEHICLE DRIVING LIGHT CIRCUITS
THE CIRCUITS ARE ENERGIZED AS FOLLOWS: (CONTINUED FROM FIGURE 8-13)
1. When master switch is energized, power is fed from the master relay to main light switch.
2. When main light switch is placed in "service drive" position, power is fed through dimmer switch, low
beam position, through service headlight low beam to ground, completing circuit. When dimmer
switch is placed in high beam position, power is fed through service headlight high beam to ground
and high beam indicator light through service blackout headlight high beam filament to ground,
completing circuit. Power is also fed from main light switch through service taillight (in left tail lamp) to
ground, completing circuit. Power is also fed from main light switch to stoplight switch through main
light switch and service stoplight (in left tail lamp) to ground, completing circuit.
3. When main light switch is placed in "stoplight" position, power is fed from main light switch to stoplight
switch, which when closed, feeds power through main light switch and service stoplight (in left tail
lamp) to ground, completing circuit.
4. When main light switch is placed in "BO MARKER" position, power is fed through both front and rear
blackout marker lights to ground, completing circuit.
5. When main light switch is placed in "BO DRIVE" position, power is fed to all blackout marker lights to
ground, completing circuit. Power is also fed to the BO/IR selector switch. When the BO/IR selector
switch is placed in "BO" position, power is fed through blackout drive light (in left headlight) to ground,
completing circuit. When the "BO/IR" selector switch is placed in "IR" position, power is fed through
the dimmer switch, low beam position, through service blackout headlight low beam to ground,
completing circuit. When dimmer switch is placed in "HIGH BEAM" position, power is fed through
service blackout headlight high beam to ground and high beam indicator light through service
headlight high beam filament to ground completing circuit. Power is fed from main light switch to
stoplight switch, when stoplight switch is closed, power is fed from stoplight switch through main light
switch to blackout stoplight (in right tail lamp) to ground, completing circuit.
8-71
TM 9-2350-230-12
TABLE 8-16. VEHICLE DRIVING LIGHT CIRCUITS - CONTINUED
8-72
TM 9-2350-230-12
TABLE 8-16. VEHICLE DRIVING LIGHT CIRCUITS (FIG. 8-13) - CONTINUED

LR headlights 427-428 P3-C P8-C 0 From switch panel, Infinity indicates open
lead through harness, to circuit or defective
dimmer switch lead.
Service head- 424 P2-M P8-G 0 From switch panel, Infinity indicates open
lights lead through harness, to circuit or defective
dimmer switch lead.
B.O. marker 43 P2-E P6 (43 0 From main light Infinity indicates open
light lead to left or switch, through circuit or defective
taillight 24) harness, to taillight lead.
marker light socket
B. 0O. marker 43 P2-E P7 (43 0 From main light Infinity indicates open
light lead to or switch, through circuit or defective
right taillight 24) harness, to taillight lead.
marker light socket
B. 0O. marker 48 P2-E P4-F 0 From main light Infinity indicates open
light lead to switch, through circuit or defective
left headlight harness, to headlight lead.
base connection
B.O. marker 48 P2-E P5-F 0 From main light Infinity indicates open
light lead to switch, through har- circuit or defective
right headlight ness, to headlight lead.
base connection
Left (service) 42 P2-H P6 (42 0 From main light Infinity indicates open
taillight lead for or switch, through har- circuit or defective
service taillight 21) ness, to service tail- lead.
light socket
Left (service) 44 P2-C P6 (44 0 From main light Infinity indicates open
taillight lead for or switch, through circuit or defective
service stoplight 22) harness, to service lead.
stoplight socket
Right (B.O.)tail- 45 P2-N P7 (45 r From main light Infinity indicates open
light lead for or switch, through circuit or defective
B. 0. stoplight 23) harness, to B.O lead.
taillight socket
High beam indi- 429 P8-H 170-210 From dimmer Infinity indicates open
cator light and switch through circuit, defective leads
leads from dim- harness, indicator or burned out bulb.
mer switch light, and indicator Zero OHMS indicates
Service headlight 426 P8-E P4-A 0 From dimmer Infinity indicates open
switch,
leads from P5-A through harness, to circuit or defective
dimmer switch
for lo beam
Service headlight 425 P8-F P4-B 0 From dimmer Infinity indicates open
switch,
leads from P5-B through harness, to circuit or defective
dimmer switch headlight base leads.
for hi beam
8-73
TM 9-2350-230-12
TABLE 8-16. VEHICLE DRIVING LIGHT CIRCUITS (FIG. 8-13) - CONTINUED

I.R. headlight 427 P8-B P4-E 0 From dimmer Infinity indicates open
switch,
leads from P5-E through harness, to circuit or defective
for hi beam
I.R.. headlight 428 P8-A P4-D 0 From dimmer Infinity indicates open
switch,
leads from P5-D through harness, to circuit or defective
for lo beam
Headlight ground 40 P4-C GND 0 From headlight Infinity indicates open
leads P5-C bases to ground circuit or defective
leads.
Headlight inter-
nal circuits -
both assemblies
are identical
Headlight ground P4-C Housing 0 Ground circuit Infinity indicates open
through internal circuit or defective
P5-C Housing wiring leads.
I.R. headlight P4-D P4-C 1. Through headlight Infinity indicates open
lo beam P5-D P5-C and bulb filament circuit, defective lead
to ground or burned out filament.
Zero OHMS indicates
short circuit.
L R. headlight P4-E P4-C .5 Through headlight Infinity indicates open
hi beam P5-E P5-C and bulb filament to circuit, defective lead
ground or burned out filament.
Zero OHMS indicates
short circuit.
Service headlight P4-B P4-C .5 Through headlight Infinity indicates open
hi beam P5-B P5-C and bulb filament circuit, defective lead
to ground or burned out filament,
Zero OHMS indicates
short circuit.
Service headlight P4-A P4-C 1. Through headlight Infinity indicates open
lo beam P5-A P5-C and bulb filament circuit, defective lead
Zero OHMS indicates
short circuit.
B. 0O. marker P4-F P4-C 30 Through headlight Infinity indicates open
light P5-F P5-C and bulb filament circuit, defective lead
Zero OHMS indicates
short circuit.
B. 0. drive light P4-G P4-C 2.6 Through headlight Infinity indicates open
and bulb filament circuit defective lead
Zero OHMS indicates
short circuit.
8-74
C8, TM 9-2350-230-12
8-9.1. Troubleshooting Odometer, Speedometer and 8-16. 2; and tachometer - table 8-16. 3. To avoid
Tachometer Circuits duplication of procedures, the speedometer and
a. Figure 8-13.1, odometer/speedometer/ odometer checkouts may be run concurrently.
tachometer wiring diagram, illustrates the electrical b. Tachometer generator checkout procedure in
circuits of the three instruments. Checkout procedures table 8-16. 3is applicable only to units with 90* angle
are tabulated as follows: Odometer - table 8-16. 1; drive adapter.
speedometer - table
8-13.1. Troubleshooting odometer, speedometer, and tachometer circuits
TABLE 8-16.1. ODOMETER CHECKOUT PROCEDURE
8-74.1
C4, TM 9-2350-230-12
TABLE 8-16. 1. ODOMETER CHECKOUT PROCEDURE (CONT’D)
8-74.2
C8, TM 9-2350-230-12
TABLE 8-16.2. SPEEDOMETER GENERATOR CHECKOUT PROCEDURE
8.74.3
C8, TM 9-2350-230-12
TABLE 8-16.2. SPEEDOMETER GENERATOR CHECKOUT PROCEDURE (CONT’D

C8, TM 9-2350-230-12
TABLE 8-16.2 SPPEDOMETER GENERATOR CHECKOUT PROCEDURE (CONT’D)
8-74.5
C8, TM 9-2350-230-12
TABLE 8-16.3. TACHOMETER GENERATOR CHECKOUT PROCEDURE
8-74.6
C8, TM 9-2350-230-12
TABLE 8-16.3. TACHOMETER GENERATOR CHECKOUT PROCEDURE (CONT’D)
8-74.7
C8, TM 9-2350-230-12
TABLE 8-16 .3. TACHOMETER GENERATOR CHECKOUT PROCEDURE (CONT’D)
8-74.8
C 13, TM 9-2350-230-12
Section 8-3. ORGANIZATIONAL PREVENTIVE - MAINTENANCE CHECKS

AND SERVICES
NOTE. All references to M551A1 in this section pertain to vehicles equipped with laser range finder.
8-10. General 8-11. General Procedures
a. Preventive-maintenance is ’he systematic care, a. Routine Application.

inspection, and service of equipment to maintain it in All of the general procedures given in table 8-17 will be
serviceable condition and to detect faults and failures followed. Organizational mechanics must be so
before extensive and time-consuming repairs or thoroughly trained in these procedures that they apply
replacements are required. The Army system of them automatically at all times in the performance of
maintenance pre- scribes two types of preventive- their duties.
maintenance services which are described in section 4-1
and b below. Refer to TM 38- 750 -for instructions on b. Operational Participation. The crew normally
use of forms pertaining to preventive- maintenance accompanies the vehicle to perform before and/or after
services. services and assist the organizational mechanics in the
performance of organizational preventive-maintenance
b. Table 8-17 contains the procedures and services.
instructions necessary to perform organizational
preventive-maintenance checks and services. These c. services. Organization- al services are defined
services are performed quarterly or every 750 miles, by, and restricted to, the general procedures outlined in
which- ever occurs first, by organizational maintenance table 8-17 unless approval to perform higher category
with the help of the vehicle crew. services has been given by the supporting maintenance
unit.
8-75
C 12, TM 9-2350-230-12
Table 8-17. Preventive-Maintenance Checks and Services
LO 9-2350-
230-12
FIG 9-61
and 9-64
Fig 9-62,
9-65, and
9-66
8-76
C 12, TM 9-2350-230-12
Table 8-27. Preventive-Maintenance Checks and Services -
Continued
Fig 9-74
Fig 9-72
Fig 9-80
and 9-81
Fig 9-86
8-76.0.1
C 12, TM 9-2350-230-12

Continued
Fig 9-119
Fig 9-140
Fig 5-7
8-76.0.2
C10, TM 9-2350-230-12
TABLE 8-17. PREVENTIVE - MAINTENANCE CHECKS AND SERVICES -

CONTINUED
QUARTERLY SCHEDULE ORGANIZATIONAL MAINTENANCE
Sequence Item to be inspected

No. Procedure Reference
HULL (EXTERIOR) - Continued

10. 1 Exterior Telephone Make sure wires are securely connected TM 11-5820-
to binding posts. Handset must provide com- 401-10, TM11-
munication with crew and must have radio cap- 5820-498-12,&
ability with RAD-TRANS-INT switches in RAD- TM 9-2350-230-
TRANS position. Replace damaged or worn door 25P/1
gasket.
ENGINE COMPARTMENT
11 Engine Cooling Unit a. Check and clean radiator fins, blow out Figs. 9-30,
any accumulation of dirt with compressed air. 31
Replace cracked or broken hoses and tighten
hose clamps.
b. Repair or replace coolant pump if leak- Fig. 9-36
age is evident.
c. Check coolant pump belt tension. Fig. 9-36
d. Check antifreeze solution for antifreeze
protection, alkalinity, and cleanliness. Service
as required to comply with TB 750-651.
12 Engine Connections Tighten loose engine connections and
and Functioning mounting screws. Start engine, observe if it
develops adequate cranking speed and starts
without excessive noise. Listen for unusual
noises in engine and generator that might
indicate improper operation or lack of lubri-
cation. Make necessary corrections.
Tighten rocker cover screws and exhaust
manifold nuts to 35 pounds-feet (engine hot
and idling).
13 Transmission Check for oil leaks. Tighten transmission 16, Tab. 9-1
trunnion screws. Tighten split-line bolts and
nuts: 10 bolts - tighten to 32-37 lb-ft. Para. 9-7a
2 nuts - tighten to 27-32 lb-ft.
14 Transmission Oil Service. Fig. 9-40
Filter
15 Exhaust Manifold Replace damaged or deteriorated exhaust Figs. 9-25,
Pipes and Mufflers system components. Tighten loose tube 26, 27
clamps and mounting bolts.
15.1 Manifold Elbow Clean manifold flexible elbow. Fig. 9-26
8-76.1
C11, TM 9-2350-230-12
TABLE 8-17. PREVENTIVE-MAINTENANCE CHECKS AND SERVICES -

CONTINUED

ENGINE COMPARTMENT - Continued

16 Generator Check generator for proper mounting. Fig 9-109,
111
17 Drive Belts Check drive belts tensioner. Replace Fig 9-109
belts if pin in rod is within 1/4 inch from
bottoming out.
18 Starter Check starter for proper mounting and/ Fig 9-113
or loose connections.
19 Air Cleaner Check air cleaner for proper mounting Fig 5-1,
and condition of ducts and clamps. 9-24
NOTE. If filter element is wet, replace
element or allow to air dry before rein-
stalling.
19.0 Air Cleaner Pre- With engine running, place hand over Fig 9-24.2
cleaner Blower air cleaner pre-cleaner discharge elbows
Motors. to check blower motor air blast.
Fig 5-3
19.1 Engine Breather Drain.
Drain Collector
Box
a. Tighten connections that show evi- Fig 9-18,
20 Fuel System dence of leaks. Clean fuel tank filler 9-21
screens of foreign matter.
b. Service fuel filters and replace Fig 9-17
elements concurrently with engine oil
filter replacement.
c. Remove water from fuel system by A, Fig 5-3
operating drain pump.
d. Service fuel tank drain pump filter Item 15,
element. Fig 9-18
21 Bilge Pumps Check pump mountings and connections. Fig 9-129,
Make sure valves function properly. 130, 131
22 Engine Air Box a. Check accumulator pressure. Fig 2-14,
(Flame) Heater 9-16
b. Check air box (flame) heater and Fig 9-14,
components for mounting and loose connec- 15
tions.
23 Engine Compart- Examine all exposed electrical controls, Fig 9-84,
ment Electrical terminals, cables, and boxes. Tighten 85
Components loose connections and mounts. Tape cables
that are frayed or have broken insulation.
8-76.2
C11, TM 9-2350-230-12

CONTINUED

ENGINE COMPARTMENT - Continued

24 Batteries Clean batteries, battery supports, re- Fig 9-97
tainers, and repaint with acid-resistant
paint if corroded. Replace batteries that
leak or have cracked cases. Remove caps
and clean vents. Test specific gravity with
a hydrometer. Tighten and grease termi-
nals and hold-downs carefully to avoid dam-
age to batteries. (TM 9-6140-200-15)
25 Fire Extinguisher WARNING: Handle charged cylinders with
care.
WARNING: Cylinder of crew compartment Fig 9-139.2
fire extinguisher becomes a dangerous pro-
jectile if accidentally discharged. Cap valve
before loosening cylinder mounting screws,
and leave cap on until cylinder is securely
mounted at installation.
a. Visually inspect all fire extinguisher Fig 1-1, 9-139
mounts, controls, and discharge lines and 9-140
nozzles. Repair or replace defective com-
ponents.
b. Remove and weigh each fire extinguish- Fig 9-139 and
er cylinder, and compare with weights 10-42.2
stamped on cylinder. If weight loss exceeds
10% of contents (full weight minus empty
weight) return cylinder to direct support
maintenance for recharging.
NOTE. Weight of crew compartment
cylinder includes cap.
25.1 Power Pack Every 6 months (every other "Q" Para 9-1
service), remove power pack from thru 9-7
hull for inspection. Service power
pack components and accessories as
required. Clean interior of power
pack compartment.
8-77
C4, TM 9-2350-230-12

CONTINUED

DRIVER’S COMPARTMENT
26 Personnel Heater Check heater, control box, and other Figs. 9-107,
components for loose connections. Clean 132,133,134
fuel filter element and pump filter.
27 Driver’s Seat and Examine for loose nuts and screws Figs. 9-123,
Rotatable Hatch and proper operation 124, 125
28 Ammunition Racks Check for broken latches and hinge pins. Figs. 9-126,
127, 128
29 Bilge Pumps Check pump mountings and connections. Figs. 9-129,

Make sure pump valves function properly. 130, 131
30 Driver’s Switch and Check panels for proper mounting and Figs. 9-101,
Indicator Panels loose connections. Observe for normal 106
readings and operation of gages, instruments,
warning lights, and indicator lights. Check
selector knob setscrews.
8-78
C9, TM 9-2350-230-12

Continued

TURRET (EXTERIOR)
31 Gun-Launcher Check Equipment Log Book for

Tube proper recording of weapon data
on DA Form 2408-4, particularly
in regard to estimated remain-
ing tube life.
Clean. Check for unusual LO 9-2350-

wear, erosion, and damage in 230-12
bore. Inspect to detect evi-
dence of decoppering and use of
unauthorized cleaning materials
and methods. Lubricate.
31.1 Stowage Rack On vehicles equipped with

Weld Pads standard turret stowage rack,
check that unused weld pads are
plugged with screws. If not,
clean threads and plug with 21
screws, MS90727-55, to preserve
threads.
32 (Deleted)
33 Dust Shield Check for dents and improper Fig 11-9
seal.
34 Hatch Doors Check to insure split hatch Fig 2-21

and Seals doors lock securely in all posi-
tions and have a watertight
seal.
35 Cupola Trav- Check wiring harness connec- Fig 2-4

erse Control tors. Tape frayed or broken
Switch As- cable insulation.
sembly
8-79
C 13, TM 9-2350-230-12

Continued

COMMANDER’S CUPOLA - M551A1 ONLY
35.1 Electrical Visually check contact ring

Contact Ring for dirt, moisture, and damage.
Use cleaning solvent and wipe
dry with clean lint-free cloth.
35.2 Electrical Visually check contact brush

Contact Brush assemblies for dirt, moisture,
Assemblies damage, or excessive wear. De-
press each brush to make sure it
activates properly and does not
stick.
Clean dirt and debris away

with small soft bristle brush
and wipe with clean lint-free
cloth.
Operate cupola drive mechan-

ism by hand and visually check
to make sure each contact brush
aligns with its proper contact
ring track.
35.3 Index Point- Inspect for loose or missing Fig 10-54

ers mounting hardware and bent or
damaged pointers.
35.4 Remote Switch a. Inspect for loose or Fig 10-35.3

Assembly missing mounting hardware.
b. Inspect for loose or

damaged toggle switch.
35.5 Cupola/Laser a. Inspect for loose or Fig 10-35.2

Control Box missing mounting hardware.
Assembly
b. Inspect for loose or

damaged toggle switches.
8-80
C13, TM 9-2350-230-12

Continued

COMMANDER’S CUPOLA - M551A1 ONLY - Continued
c. Inspect for burned out

or missing power lamp.
35.6 Cupola (Relay) a. Inspect for loose or Fig 10-33

Control Box missing mounting hardware.
Assembly
b. Inspect electrical con-
nector for moisture or damage.
35.7 Cupola Drive a. Inspect for damaged or

System Elec- severed wires.
trical Cable
Assembly b. Inspect electrical connec-
tors for moisture, damage, and
for proper alignment.
AUXILIARY EQUIPMENT TO LASER RANGE FINDER - M551A1 ONLY
35.8 Loader’s Per- Inspect loader’s periscope Fig 10-54

iscope Stop stop to make sure mounting hard-
ware is tight. Check two stop
pins to see if loose or damaged.
35.9 Resistor Box a. Inspect for loose or Fig 10-35.4

Assembly missing mounting hardware.
b. Inspect electrical con-

nector for moisture or damage.
35.10 Laser Control a. Inspect for loose or miss- Fig 10-56

Handle ing mounting hardware.
b. Inspect brow pad lock

release for proper operation.
Clean and lubricate (OE10),

as necessary, to insure locking
plungers slide freely.
8-80.1
C 13, TM 9-2350-230-12

Continued

AUXILIARY EQUIPMENT TO LASER RANGE FINDER -

35.11 Laser Range Inspect for loose or missing Fig 10-57

Finder Ex- mounting hardware. and 10-58
ternal Pro-
tective Cov-
ers and Ca-
ble Covers
CAL .50 MACHINE GUN, M2 HB
Refer to TM 9-1005-213-25.
36 (Deleted)
37 (Deleted)
38 (Deleted)
CAL .50 MACHINE GUN MOUNT ASSEMBLY
39 Machine Gun With machine gun installed, Fig 2-4
Mount Assem- elevate and depress throughout
bly entire range, Insure all com-
ponents are intact.
Check for ineffectual action Fig 3-14

in either elevation or depres-
sion. If slow or faulty, dis-
assemble, clean, and lubricate.
Check carefully for cracks or Para 8-5

damage to parts. Remove rust and
burs with fine emery cloth and
file. Paint non-machined sur-
faces as required.
TURRET (INTERIOR)
40 Hatch Seals Repair or replace damaged or Fig 10-44

loose hatch seals and protec-
tion pads.
8-80.2
C 14, TM 9-2350-230-12

--Continued

TURRET (INTERIOR) -- Continued
41 Cushions and Repair or replace torn cush- Fig 10-39,

Backrests ions and backrests. 10-41, and
10-42
42 Turret Elec- Check all connections to in- Fig 10-1

trical System sure they are secure. Check
selector knob setscrews. Check
dome light dimmer switch located
at loader’s position. If insul-
ating compound is worn or mis-
sing from terminals, apply new
adhesive MIL-A-46106 (fig 9-
95.1).
43 Contact Ring Tighten contact ring mounting Fig 10-28

and Electri- screws, connectors, and ground
cal Cables lugs. Tape frayed or broken
cable insulation.
44 Gas-Particu- Change particulate filter Table 2-6

late Filter when contaminated. and fig
Unit MSA3 10-31
152-MM GUN-LAUNCHER AND MOUNT
45 Mount Elevate and depress weapon

through entire range to note
performance.
46 Buffer Check counterrecoil buffer LO 9-2350-

for leaks and oil level. Re- 230-12
plenish as necessary.
47 Reservoir a. Check reservoir fittings Fig 11-5,

for-loose connection. 11-7, and
11-8
8-80.3
C14, TM 9-2350-230-12

--Continued

152-MM GUN-LAUNCHER AND MOUNT -- Continued

47 Reservoir b. Remove and inspect filter.
--continued Replace if tears or holes are
found in screen. Clean with a
regular cleaning solvent (sol-
vent must be clean) . Allow
screen to air dry. Do not dry
screen under air pressure, as
damage to screen mesh may re-
sult.
c. Check reservoir fluid

level.
48 Safe to Fire Check mechanism for proper Fig 3-2

Mechanism function.
49 Breech Assem- Open and close breech manu- Table 5-8.1

bly ally and electrically, clean and
lubricate. Check all compo-
nents for unusual wear or
cracks. Observe following com-
ponents for proper operation:
a. Manual crank handle. A and B,

Fig 3-1
b. Electric drive motor. Steps 10-15,

table 3-3
8-80.4
C11, TM 9-2350-230-12
TABLE 8-17. PREVENTIVE-MAINTENANCE CHECKS AND SERVICES-CONTINUED


152MM GUN-LAUNCHER AND MOUNT -

Continued
49 Breech Assembly - c. Loading tray and ejector. Fig 11-20,
Continued 21
d. Detent and trigger lever. Fig 11-22,
23
e. Obturator gasket Fig 11-24
50 Electrical Harness Check for proper operation and condition, Fig 11-22,
and Limit Switches 13, 2
51 Firing Mechanism Clean contact of firing mechanism Fig 11-13

with rough cloth or steel wool,
5350-242-4404. Check continuity. Table 11-2
NOTE. Service requirements for the firing mechanism are based

on usage rather than time. Refer to table 8-17.1.
52 Carrier Cover Inspect and clean. Fig 11-25

Vent Plug
52.1 Detent, Check Valve, Service requirements for these items

Gun Tube, Coupling, are based on usage rather than time interval.
Breech, Compressor, Refer to table 8-17. 1.
and Related Parts
CAUTION: Avoid damaging air cylinders. which are under very high pressure.
7.62MM MACHINE GUN

Checks 53 through 57 deleted. See T.M 9-1005-233-25.
NOTE. The purging and charging techniques described in TM 750-116 will be
performed on the XM44, M47 and M48 periscopes, M119 Telescope, and M149
Mount when condensation in the instrument is evident or every 90 days. XM44E
Series Periscope requires purging at any time head and body are separated.
58 M13A1C Quadrant a. Inspect for general condition and com-

pleteness. Note legibility of scales and in-
dices; clean as required. Check that level
vial rotating cover is in a protective position
when quadrant is not in use.
b. Check for tightness of screws, binding, B, Fig 2-28
legibility of scales, condition of level vial
and cover. Check adjustment.
59 XM44 Series Periscope a. Check synchronization and alignment ac- Tables 2-9,
curacy of periscope with 152MM gun-launcher. 11-6
8-81
C10, TM 9-2350-230-12
TABLE 8-17. PREVENTIVE-MAINTENANCE CHECKS AND SERVICES - CONTINUED

SIGHTING AND FIRE CONTROL - Continued
59 XM44E Series Peris- b. Check for excessive backlash in the

cope - Continued periscope and 152MM gun elevation system.
c. Inspect wiper blades; replace if neces- Fig. 11-42
sary. Inspect general condition and complete- Fig. 2-26
ness. Check operation of knobs and levers.
Inspect lens and windows for dirt, cracks,
and chips. Check electrical connections. Re-
place lamps if defective. Check periscope
washer fluid reservoir and refill.
59.1 M119 Telescope Check reticle ground strap connections at
conventional reticle elevation knob mounting
flange and reticle light holder. Connections
must be tight.
60 M47 and M48 a. Check that all components of the wiper Fig. 2-7
Periscopes assembly are functioning properly.
b. Inspect wiper blades; replace if nec-
essary. Check pump to see that pressure
forces fluid from reservoir. Inspect tubing
for leaks.
c. Check periscope washer fluid reservoir
and refill.
MISSILE SUBSYSTEM UNITS
61 Cable Assemblies Check condition and tightness of all
connectors. If replacement of cables is
required, notify direct support personnel.
62 Optical Tracker, a. Inspect mounting screws and electrical
Power Supply connections. Tighten if necessary.
Modulator, Rate b. Perform transmitter alignment check
Sensor, Signal Fig. 10-20
Data Converter, quarterly or whenever transmitter alignment
and Optical becomes questionable for any reason.
Transmitter c. Notify support maintenance to perform
beam pattern check semiannually.
ROAD TEST
NOTE. Road test vehicle approximately
3 to 5 miles. When tactical situation does
not permit a complete road test, perform
the following tests:
63 Engine Governed Start engine and warm up. With shift
Speed, Performance lever in N (neutral) position, fully accelerate
and No-Load Test engine. Engine should develop 2940 to 2990
rpm. Idle speed should indicate 650-700rpm.
Test engine for normal acceleration and
power in each transmission range.
8-82
C6, TM 9-2350-230-12

ROAD TEST - Continued

63 Engine Governed While testing in low range, accelerate
Speed, Performance with wide open throttle from low speed
and No-Load Test - to top speed. Listen for unusual noises
Continued that might indicate loose, damaged, ex-
cessively worn parts, or loose mount-
ings. Repair and adjust linkage if nec-
essary.
64 Engine and Trans- Start engine and allow coolant to reach
mission Stall Test operating temperature (1800 to 2000F).
(Based on use of With brake pedal fully depressed, move
DF-2 fuel, NATOF- shift lever to "4" position and fully ac-
54). celerate engine for a maximum of 15 sec-
onds. The engine should develop 2100
rpm minimum. Failure to attain this
speed indicates engine malfunction. If
stall speed exceeds 2400 rpm trans-
mission trouble is indicated.
65 Instruments and Check instruments for normal indication.
Gages
CAUTION. If gages do not indicate nor-
mal readings after engine and transmission
have been run long enough to reach normal
operating temperature, stop engine and
refer to troubleshooting procedure table
8-4).
Tachometer and Speedometer should
operate without excessive fluctuation or un-
usual noises.
66 Steering Controls Move steering T-Bar through its entire Fig. 9-53
range and observe if steering response is
satisfactory. With vehicle operating at mod-
erate speed and T-Bar centered, observe if
there is any tendency to wander or pull to
one side. Repair and adjust linkage if nec-
essary.
67 Transmission Shift through all ranges, noticing if it shifts Fig. 9-47
smoothly without excessive vibration or un-
usual noise, and if vehicle response is satis-
factory. Compare driver’s shift control lever
position with position of transmission shift
control lever. They should be synchronized
in all positions. Repair and adjust linkage if
necessary.
8-83
C6, TM 9-2350-230-12

ROAD TEST - Continued
68 Brakes Accelerate vehicle to a moderate speed, Fig. 9-44

release accelerator and apply brake, ob-
serving if vehicle stops effectively without
pulling to one side. With the vehicle stopped
on an incline, depress brake pedal and apply
parking brake handle. Note if brakes lock
securely and vehicle is held in place. Re-
pair and adjust if necessary.
AFTER ROAD TEST
69 Road Wheels, Check temperatures immediately after

Hubs, and Shock road test. Refer to "AFTER OPERATION"
Absorbers preventive-maintenance services, table 4-1,
step 77.
70 Vehicle Visually inspect all areas inside and out-

side vehicle for evidence of fuel or oil leaks.
70.1 Engine Mount Tighten engine mount screws. Fig. 9-3

Screws
FINAL ROAD TEST
71 After all services and inspections have been

completed, take the vehicle on a short road
test to insure corrections of operational de-
ficiencies. Pay particular attention to those
items that were initially defective.
UNUSUAL CONDITIONS
Vehicles exposed to extreme-cold or hot

weather will require more frequent servicing.
Materiel subjected to salt-water immersion
should be evacuated to support maintenance
unit as soon as possible after exposure.
EXTREME-COLD WEATHER
72 Cooling System Test radiator coolant for proper anti-freeze Par. 9-10
protection.
73 Lubricants Make sure all components are lubricated App. IV

with correct grade of lubricant for expected
temperature.
8-84
C11, TM 9-2350-230-12
TABLE 8-17.1. PREVENTIVE MAINTENANCE CHECKS AND SERVICES-

PRIMARY ARMAMENT AND RELATED EQUIPMENT
INTERVAL COMPONENT PROCEDURE REFERENCE
CAUTION: Avoid damaging air cylinders, which are under very high pressure.
After each Ammunition Removal/installation (Type ) - - - - - Fig 11-22,
day’s firing - detent Clean, inspect and repair (Type I) - - - Fig 11-23
not to exceed assembly Removal/installation (Type I) - - - - - Fig 11-23.1
40 rounds (Type I or Disassemble/assemble (Type 1m --- Fig 11-23.2
between 11 only - Clean, inspect, and repair (Type II) - Fig 11-23.3
cleaning para 3-3.4)
or NOTE. Where additional firing is not
Every 90 days anticipated, remove and clean detent assembly
when not and detent hole for three consecutive days as
firing for cannon tube (LO 9-2350-230-12)
Not to exceed Check valve Disassemble and clean with TPM or RBC. Fig. 11-10.1,
100 rounds 10.2, 10.3
Not to ex- Firing Disassemble and clean with TPM or RBC. Fig 11-13
ceed 200 mechanism Inspect contact and seal seat on breechblock
conven- face.
tional
rounds
400 Rounds Compressor Disassemble and clean with TPM or RBC dry with Fig. 10-17.4
or 30 Com- Air Intake compressed air. Replace strainer/filter if de-
pressor hours Strainer teriorated, clogged, or damaged.
(More Fre-
quently under
dusty condi-
tions)
400 Rounds or Compressor Replace cartridge. Fig. 10-17.3
30 compres- Chemical a. Visually inspect compressor for general
sor hours Dryer physical condition, bent pins, fan blade
alignment, deformed tubing, and loose or
defective mounting hardware.
b. Check oil level with dipstick and add oil if Fig. 3-2.4
required.
CAUTION: 1. Use extreme care to avoid oil
contamination.
2. Use ONLY air compressor
lubricating oil FSN 9150-753-4667.
3. Do not overfill
c. Operate compressor (with vehicle engine
operating at fast idle, or with auxiliary power
source) to check for excessive noise or
vibration, and to check operation of moisture
separator dump cycle. Moisture separator
should shut down compressor and dump
accumulated moisture for approximately
10 seconds every 25-35 minutes.
8-85
C10, TM 9-2350-230-12

PRIMARY ARMAMENT AND RELATED EQUIPMENT - CONTINUED
d. Leak-test any disturbed or suspected air con-

nections with liquid soap with system under
pressure.
WARNING: Do not tighten fittings or perform

any work on equipment during compressor operation
or when system is under pressure. Do not tamper
with pressure relief valves.
600 Rounds Gun Tube, Gun tube, obturator seal, coupling and breech
Obturator Seal, chamber are to be replaced as a unit. Notify
Coupling and support maintenance.
Breech
Chamber
1200 Rounds Compressor a. Remove compressor. Fig. 10-17.1

or 100 Com-
pressor b. Remove dipstick and drain plug to drain nil Fig. 10-17.5
hours from compressor sump. Allow approximately
5 minutes to permit oil tubes to drain com-
pletely.
c. Disconnect oil line at oil strainer adapter. Fig. 10-17.5

Remove and clean strainer with TPM or RBC and
dry with compressed air. Inspect strainer
for deterioration or damage and replace if
defective.
d. If excessive foreign material was evident Fig.- 10-17.5

on strainer or in strainer cavity, it will be
necessary to flush sump before refilling.
e. Install strainer (with new preformed Fig. 10-17.5

packing) and connect oil line.
f. Install drain plug and fill sump with Air Corn-

pressor Lubricating oil. See paragraph 1-6g.1
for correct quantity of oil.
g. Install dipstick using new preformed packing. Fig. 10-17. 5
h. Install compressor and leak test all disturbed Fig.10-17.1

or suspected connections with liquid soap.
8-86
C12, TM 9-2350-230-12

PRIMARY ARMAMENT AND RELATED EQUIPMENT - CONTINUED
Every 30 152MM a. Assure recoil mechanism is pressurized, and

days when gun safe to fire indicator is in SAFE position.
not firing launcher
recoil b. Assure turret travel lock is engaged.
mechanism
c. Using exercising bracket on wrecker boom, Fig. 8-14
position wrecker and M551 vehicle to assure Fig. 8-15
wrecker boom and gun launcher tube are on Fig. 8-16
the same plane and square with each other.
NOTE: It may be necessary to position rear

of the M551 on an incline and elevate cannon to
assure plane alignment, i.e., straight line of
wrecker boom and gun launcher:
d. Mark a chalk line on the gun launcher tube (or

bore evacuator if 81 MQD) 6 to 8 inches forward
of dust cover.
e. Extend boom of wrecker until wood block of

exercising bracket contacts gun launcher
muzzle.
CAUTION: Assure precise alignment of gun

launcher and wrecker boom to prevent component
damage.
f. Extend wrecker boom until gun launcher has

been moved out of battery 6 to 8 inches (chalk
line) then retreat boom.
g. Repeat operation at least 10 times to insure

that recoil sliding areas and seals are lubri-
cated.
h. Leave recoil mechanism in normal precharged

pressure condition.
8-87
C12, TM 9-2350-230-12
Figure 8-14. Extension bracket for M543A2 wrecker.
8-88
C12, TM 9-2350-230-12
Figure 8-15. Extension bracket for M62 wrecker.
8-89
C12, TM 9-2350-230-12
Figure 8-16. Exercising recoil mechanism on M551 with wrecker.
8-90
C4, TM 9-2350-230-12
CHAPTER 9
ORGANIZATIONAL MAINTENANCE-POWER PLANT
AND HULL
Section 9-1. POWER PLANT

9-1. General
to prevent damage to the power plant and/or power plant
a. This section contains organizational compartment. Personnel should be stationed at the
maintenance procedures for the removal/installation of front, rear, and both sides of the power plant for
the power plant, engine mount, and engine mount observation of clearances and to assist during the lifting
supports. operation.
9-2. Power Plant Removal Preliminary Prep- a. Lift power plant upwards and to the rear to
arations remove from compartment. Check constantly to
maintain clearance during the lift-ing operations.
NOTE. The power plant removal and installation are
to be coordinated with a support ing maintenance unit b. Test stands or mounting frames should be used
only if removal is for replacement of engine or if available. However, it is possible to set the power plant
transmission. Prior to removal or installation, make on blocks (fig. 9-6), using precautions to avoid any
certain that all necessary manpower and equipment are contact with the steel engine oil pan and the coolant
available. crossover tube.
a. It is recommended that four men be assigned to c. Do not drain or disconnect cooling system hoses
the removal and installation of the power plant. when removing power plant unless vehicle is equipped
with a winterization kit.
b. The hoisting equipment used to remove and
install the power plant should have a minimum lifting 9-5. Operating Power Plant When Removed
capacity of 3500 pounds, minimum reach of 9 feet, and From Vehicle
minimum lift of 10 feet. Hoisting equipment should be a. Operation of the power plant, when re-moved
movable or provisions made to move the vehicle as the from the vehicle, enables maintenance personnel to
power plant is being removed. inspect the control and drive components by hand-
operating the control link-ages on the transmission
c. Allow ample room to work on all sides of power without any injurious effects to the mechanisms.
plant after it is removed from vehicle.
b. Special extension fuel input and return hoses,
9-3. Power Plant Removal Procedure fittings, and wiring harnesses (fig. 9-10) are supplied to
facilitate operation of the power plant when removed
Four properly trained men can remove the power plant in from vehicle.
approximately twenty-five minutes. The removal
procedures are sequenced in progressive order and are CAUTION: If power plant is operated while
coordinated for accomplishment by two, two-man teams. mounted on blocks, watch closely to prevent power plant
Team "one" to accomplish all opera-tions from top of from vibrating off blocks (fig. 9-6).
vehicle. Team "two" to accomplish all operations
accessible from the ground. Power plant removal 9-6. Performing Stall Test
sequence is illustrated in figures 9-3 through 9-6.
Refer to table 8-17, item 64 for stall test procedures.
9-4. Lifting Power Plant From Vehicle (Fig-
ure 9-5) 9-7. Power Plant Installation Preliminary
Preparations
NOTE. Proper positioning of the lifting sling is
necessary to balance the power plant a. Preparation of Power Plant Compartment. With
the power plant out of the
9-1
C10, TM 9-2350-230-12
vehicle, remove all foreign material from the power plant (10) If replacement engine has serial number
compartment and wipe all accessible surfaces clean with previous to 6D-33513, see fig. 9-15.1 for air box heater
wiping cloths. Inspect fixed fire extinguisher spray tubes. components which may be removed from old engine for
If power plant compartment is extremely dirty, it may be installation on new engine.
steam cleaned and/or wiped with a suitable cleaning
solvent. (11) Insulation from exhaust manifolds, elbows,
and crossover pipe (figs. 9-25 and 9-27).
NOTE. Whenever power plant is removed from
vehicle, the "split-line" bolts and nuts (attaching (12) Tachometer generator (right angle drive
transmission converter housing to engine flywheel only) (figs. 9-115 and 116).
housing) should be retorqued:
10 bolts - tighten to 32-37 lb-ft. (13) Engine coolant temperature and oil
2 nuts - tighten to 27-32 lb-ft. pressure switches and transmitters (fig. 9-114).
b. Power Plant Replacement. Replacement of (14) Winterization kit inlet and outlet coolant
engine and transmission assemblies will require build-up hoses and fittings, if installed.
to a complete power plant before installation in the
vehicle. Serviceable components may be removed from (15) Support maintenance personnel shall
the old power plant and installed on the replacement remove power plant harness and crank-shaft pulley from
engine and/or transmission assemblies. old engine and install on replacement engine.
c. Engine Replacement. When it is neces-sary for CAUTION: Discard shipping screw and
support maintenance to replace the engine, the following washer from new engine crank-shaft and
items must be removed from old engine and installed on reuse screw and washer from old
new engine. crankshaft, or replace with correct parts
(TM 9-2350-230-25P/1).
(1) Engine coolant system (figs. 9-28 through
9-35 and 9-38). d. Transmission Replacement. When it is
necessary for support maintenance personnel to replace
(2) Air box engine breather drain collector, the transmission, the following components must be
tubes, hoses, and fittings (fig. 9-13). removed from defective transmission and installed on
new transmission by organizational maintenance
(3) Transmission oil cooler elbows (2) from personnel.
cooler (fig. 9-12).
(1) Starter relay and mounting bracket fig. 9-
(4) Engine oil pressure switch (fig. 9-113). 100).
(5) Fuel shut-off controls and bracket with (2) Electrical harness receptacle with bracket
special screw, fuel shut-off lever (fig. 9-23), governor (item 7, table 9-1) and power plant harness from
arm and throttle rod (fig. 9-45). transmission.
(6) Generator belt tensioner and bracket (fig. 9- (3) Transmission oil cooler hoses, oil pressure
109). switch, temperature switch (figs. 9-12, 9-114) and elbows
(2), and oil level indicator (fig. 9-41).
(7) Generator and drive assembly (figs. 9-111,
112). Five screws, washers, and generator mounting (4) Throttle, shift, land steer and water steer
bracket. Ground cable and generator/starter-to-voltage control assembly components from transmission. Refer
regulator electrical harness. to figures 9-45, 9-46, 9-52 and 9-55.
(8) Engine mounts (fig. 9-7). (5) Brake control components (fig.9-50, 51).
(9) Main fuel hose quick disconnect, elbow,

drain (2), and drain elbow (2) on fuel filters (fig. 9-11).
9-2
C11, TM 9-2350-230-12
1. STARTER RELAY BOX 14. COOLANT DRAIN PLUG

2. ENGINE EXHAUST ELBOW 15. GENERATOR
3. MAIN FUEL HOSE QUICK DISCONNECT 16. ENGINE MOUNT SCREW
4. PRIMARY FUEL FILTER 17. ENGINE STARTER MOTOR
5. ENGINE OIL FILLER CAP 18. MOUNTING SCREW
6. CRANKCASE BREATHER HOSE 19. POWER PLANT GROUND CABLE
7. AIR BOX ACCUMULATOR 20. TRANSMISSION OIL FILTER
8. RADIATOR COOLANT FAN 21. GENERATOR-TO-VOLTAGE REGULATOR HARNESS
9. RADIATOR 22. STARTER-TO-BATTERY CABLE
10. RADIATOR OUTLET TUBE ASSEMBLY 23. SPEEDOMETER GENERATOR
11. GENERATOR/COOLANT FAN DRIVE BELTS 24. ODOMETER ADAPTER
12. BELT TENSIONER 25, SPEEDOMETER CABLE ADAPTER
13. GENERATOR DRIVE ASSEMBLY 26. BRAKE CABLE
TA0073171
Figure 9-1. Power plant - right side - reference.
9-3
C11, TM 9-2350-230-12
1. RADIATOR 11. TRANSMISSION OIL PRESSURE SWITCH

2. RADIATOR COOLING FAN SHROUD 12. TRANSMISSION OIL TEMPERATURE SWITCH
3. INLET THERMOSTAT HOUSING 13. ENGINE OIL FILTER
4. ENGINE CRANKCASE BREATHER HOSE 14. ENGINE OIL LOW PRESSURE SWITCH.
5. ENGINE OIL LEVEL GAGE 15. ENGINE BREATHER DRAIN COLLECTOR
6. COOLANT SURGE )ANK 16. ENGINE FUEL RETURN HOSE
7. TRANSMISSION OIL LEVEL GAGE 17. ENGINE/TRANSMISSION OIL COOLER
8. TURBOCHARGER 18. AIR BOX DRAIN HOSE
9. ELECTRICAL HARNESS RECEPTACLE 19. ENGINE COOLANT PUMP
10. TRANSMISSION 20. RADIATOR COOLANT FAN
21. AIR-CLEANER BLOWER RELAY SWITCH.
(OIL PRESSURE).
TA0073181
Figure 9-2. Power plant - left side - reference.
9-4
C11, TM 9-2350-230-12
Figure 9-3. Removal/installation - power plant (1 of 4)
9-5
C11, TM 9-2350-230-12

9-6
C11, TM 9-2350-230-12
TABLE 9-1. REMOVAL/INSTALLATION - POWER PLANT (FIGURE 9-4)
STEP PROCEDURE
1 Loosen clamps (2) on air cleaner duct and remove duct. Cover turbocharger and air
cleaner openings to keep out foreign matter.
INSTALLATION NOTE. Tighten clamps to 50-60 pounds-inch.
2 Disengage return fuel line at quick disconnect and place hose on engine.
3 REMOVE 2 SCREWS, WASHERS, NUTS, AND RETAINER FROM LEFT SIDE OF SHROUD.
4 Disconnect main fuel line at quick disconnect and place hose clear of power plant.
5 Remove 2 screws, washers, and ground cable from hull and replace screws and washers
in hull Place cable on power plant.
6 Disconnect generator cable from voltage regulator and starter cable at slope plate
bracket. Place cables on power plant.
7 Unscrew nut, disconnect power plant harness and place harness clear of power plant.
8 Unscrew nut and remove speedometer adapter and adapter key (1 and 4, fig. 9-116).
NOTE. Tape adapter key to speedometer cable to prevent loss.
9 Remove 2 screws, washers, and step plate from top of engine.

INSTALLATION NOTE. Tighten screws to 35 pounds-feet.
10 Remove cotter pin and clevis pin from fuel shut-off clevis.
11 Loosen jam nuts and remove fuel shut-off cable at bracket. Remove clamp from shroud
and place cable clear of engine. Install step plate and temporarily install screws and
washers (step 9).
INSTALLATION NOTE. See Figure 9-22 for fuel shut-off adjustment.
12 Remove 2 screws, washers, and protective plate.
13 Remove cotter pins and clevis pins from both brake cable clevises and remove brake
cable from transmission.
14 Remove 4 cotter pins and clevis pins, then disconnect land steer, water steer, throttle,
and shift linkage.
INSTALLATION NOTE. See Figures 9-45, 46, 52, and 55.
15 Remove 3 control bracket screws and lift bracket with control cables from transmission
and stow on rear hull slope, clear of power plant. If control cables are removed from
transmission control cable support bracket, refer to figures 9-44, 9-47, 9-53 and
9-54 for proper adjustment.
INSTALLATION NOTE. Tighten screws to 20 to 24 pounds-feet.

16 Remove 2 screws and trunnion mount caps from each side of transmission. Mark
trunnion caps right and left, front and rear, to facilitate installation.
INSTALLATION NOTE. Make certain trunnion inserts are properly in place
before installing power plant. Tighten trunnion mount cap screws to 85-90 pounds-feet.
9-8
C4, TM 9-2350-239-12
CAUTION: ON VEHICLES EQUIPPED WITH

WINTERIZATION KIT, DRAIN COOLANT
SYSTEM (TABLE 5-4) AND DISCONNEC
UPPER AND LOWER ENGINE HOSES TO
WINTERIZATION KIT COOLANT AND
BATTERY HEATER FITTINGS.
INSTALL SHIELDS ON FRONT AND BOTH SIDES OF

RADIATOR.
ATTACH LIFTING SLING TO POWER PLANT AT FOUR (4)

PLACES. OBSERVE AND ADJUST TURN BUCKLES, IF
NECESSARY, TO RAISE POWER PLANT AS LEVEL AS
POSSIBLE. SLOWLY LIFT POWER PLANT FROM VEHICLE.
CAUTION: DURING POWER PLANT REMOVAL OR

INSTALLATION USE EXTREME CARE TO
PREVENT DAMAGE TO TORSION BARS.
WATCH RADIATOR, ENGINE COMPONENTS, AND ALL

SIDES OF POWER PLANT TO BE SURE THEY CLEAR
HULL, AIR CLEANER, AND OTHER PERMANENTLY
INSTALLED COMPONENTS.
PLACE POWER PLANT ON APPROPRIATE STAND OR

SUITABLE WOOD BLOCKS (FIG. 9-6).
INSTALLATION NOTE. BE SURE TO REMOVE ALL

RADIATOR SHIELDS AFTER INSTALLING POWER PLANT
IN VEHICLE.

9-8
C8, TM 9-2350-230-12
A. WHEN POWER PLANT HAS BEEN

REMOVED FROM VEHICLE, PLACE ON
SUITABLE STAND WHICH WILL ALLOW
AMPLE WORKING AREA ON ALL SIDES OF
POWER PLANT.
B. POMWER PLANT MAY BE SET ON CLEAN HARD C. PLACE MUFFLER ON BLOCK TO PREVENT
SURFACE. SUPPORT FRONT OF POWER PLANT DAMAGE TO EXHAUST ELBOW. (NOT
WITH 4 X 4 WOOD BLOCK PLACED BENEATH REQUIRED IF ENGINE ACCESS COVER HAS
RADIATOR SUPPORT AS SHOWN. BLOCK MUST BUILT-IN MUFFLER GUARD.)
NOT CONTACT COOLANT CROSSOVER TUBE
WE 12173

9-9
C10, TM 9-2350-230-12
PRELIMINARY STEPS
REMOVE POWER PLANT FROM VEHICLE (FIGURES
9-3 THROUGH 9-6).
REMOVAL - RIGHT MOUNT
1. REMOVE 2 SCREWS, LOCK PLATE AND FLAT

WASHERS FROM REAR OF RIGHT ENGINE
MOUNT ASSEMBLY.
2. REMOVE 2 SCREWS, LOCK PLATE, FLAT

WASHERS, AND ENGINE MOUNT ASSEMBLY
FROM RIGHT SIDE OF ENGINE.
REMOVAL - LEFT MOUNT

3. DRAIN ENGINE COOLANT SYSTEM.
4. REMOVE 2 SCREWS, FLAT WASHERS, LOWER

HOSE CLAMP AND COOLANT PUMP INLET
ELBOW, GASKET, AND HOSE.
CAUTION: DO NOT PRY HOSES OFF TUBES AS
TUBE ENDS MAY BE DAMAGED AND LEAKS
RESULT.
INSTALLATION NOTE. USE NEW GASKET AT
INSTALLATION.
5. REMOVE 2 SCREWS, LOCK PLATE AND FLAT
WASHERS FROM REAR OF LEFT ENGINE
MOUNT ASSEMBLY.
6. REMOVE 2 SCREWS, LOCK PLATE, FLAT
WASHERS AND THE ENGINE LEFT MOUNT
ASSEMBLY.
INSTALLATION
REVERSE REMOVAL PROCEDURE. ITEMS 1 AND 5:
TIGHTEN SCREWS TO 250-300 POUND-FEET AND
BEND CORNERS OF LOCK PLATE TO LOCK
SCREWS.
ITEMS 2 AND 6: TIGHTEN SCREWS TO 100-120
POUND-FEET AND BEND CORNERS OF LOCK
PLATE TO LOCK SCREWS.
WE 66677
Figure 9-7. Removal/installation - engine mount assembly
9-10
C11, TM 9-2350-230-12
A-ENGINE MOUNT - INSTALLED
Figure 9-8. Removal/installation - engine mount supports
Figure 9-9. Disassembly/assembly/repair-engine mount assembly
9-11
C11, TM 9-2350-230-12
Figure 9-10. Test operation of power plant out of vehicle
9-12
C11, TM 9-2350-230-12
Section 9-2. ENGINE AND COMPONENTS

9-8. General procedures for engine and components shown in table
9-2, and paragraphs 9-9 and 9-10.
This section contains organizational maintenance
TABLE 9-2. ENGINE AND COMPONENTS

FIGURE REFERENCE
ASSEMBLY OR COMPONENT SERVICE ADJUST REPLACE REPAIR
Oil Filter, Element, and Cover Assembly 9-11 9-11
Engine/Transmission Oil Cooler Cores 9-12
Engine/Breather Drain Collector Hoses, Tubes, 9-13
and Fittings
Air Box Heater Components 9-14
Air Box Heater Pump/Valve, Coil, and Accumulator 9-16 9-15
Fuel Filters and Elements 9-17
Engine Fuel System Hoses and Fittings (Refer to 9-18
Para 9-9)
Fuel Pump (Refer to Para 9-9) 9-19
Fuel Tank Shut-off Valve 9-20
Fuel Filler Cap and Filter 9-21
Fuel Shut-off Control and Linkage 9-22 9-23 9-23
Engine Air Cleaner and Components 5-1 9-24 9-24
Filter and Air Cleaner 9-24.1

Blower Assembly and Hose 9-24.2
Hull Wiring Harness and Leads 9-24.3
Engine Wiring Harness 9-24.4
Exhaust Manifolds and Elbows 9-25
Exhaust Muffler and Components 9-26
Exhaust Crossover Pipe 9-27
Engine Coolant System (refer to para 9-10) 9-28
Radiator Shrouds and Seals 9-29 9-29
Coolant Radiator 9-30,
9-31
Coolant Fan and Pulley 9-32
Coolant Fan/Generator Drive Belts 9-109
Coolant Fan Clutch Assembly 9-33
Surge Tank 9-34
Coolant Tubes, Hoses, and Fittings 9-35
Coolant Pump 9-36
Coolant Thermostat Housing and Thermostat 9-37
Radiator Support 9-38
9-13
C4, TM 9-2350-230-12
9-9. Engine Fuel System (Fig. 9-17)
a. Checking Fuel Flow. (1) Insert end of a wire through one of the pump
body drain holes, then crank engine momentarily
(1) Open exhaust grille doors, disconnect fuel return and see if wire vibrates. Vibration will be felt if
hose at quick disconnect (Fig. 9-4), remove pump shaft rotates.
disconnect from hose and place end of hose in a
one gallon container. (2) Without removing pump from engine, unscrew
valve plug; and remove gasket, spring, pin, and
(2) Start and run engine at 1200 rpm and measure valve. Wash parts with solvent and blow out
the fuel flow return for a period of one minute. valve cavity with compressed air. Install valve
Approximately one-half gallon of fuel should flow parts and check flow.
from the return hose per minute.
9-10. Engine Coolant System (Fig. 9-28)
(3) Immerse end of fuel hose into fuel container. Air
bubbles rising to the surface of the liquid will a. When coolant system has been drained to service
indicate a leak on the suction side of the pump. coolant components, the system should be flushed to
Check all hose connections and gaskets on remove scale deposited by hard, mineral-laden water.
strainer and filter elements.
(1) Drain system (table 5-4).
(4) If the fuel flow is insufficient for satisfactory
engine performance, then check the strainer (2) Refill system with clean soft water. If engine is
element and filter element and replace either or hot, fill slowly to prevent distortion of engine
both if clogged. Start engine and run it at 1200 castings.
rpm to check fuel flow. If fuel flow is still
unsatisfactory, replace fuel pump (fig. 9-19) and (3) Start engine and operate for 15 minutes.
again check flow. When changing a fuel pump,
clean pump lines with compressed air and be (4) Drain coolant system completely (table 5-4).
sure all fuel line connections are tight.
(5) Refill cooling system according to Table 9-2.1.
(5) Connect fuel return hose to quick disconnect.
b. Whenever hose connections have been disturbed or
b. Checking Fuel Pump. If the fuel pump fails to when coolant system has been drained, retorque clamps
function properly, check for broken pump shaft or dirt in to 40-60 pounds-inches after engine has been operated
relief valve before removing the pump from the engine: to normal operating temperature.
TABLE 9-2.1. COOLANT MIXTURE

AMBIENT
TEMPERATURE ANTIFREEZE INHIBITOR PROPORTION
-65°F to -40°F 6850-174-1806 -------- Full strength
6850-243-1992 --------
-40°F to+80°F or -------- 50-50
6850-224-8730 --------
Above 80°F -------- 6850-753-4967 22-1/2 oz.
9-14
C11, TM 9-2350-230-12
Figure 9-11. Removal/installation - engine oil filter, element, and adapter.’
9-15
C11, TM 9-2350-230-12
Figure 9-12. Removal/installation - engine/transmission oil cooler cores
9-16
C11, TM 9-2350-230-12
Figure 9-13. Removal/installation/service - engine breather drain collector hoses,
9-17
C2, TM 9-2350-230-12
Figure 9-14. (Superseded) Removal/installation/repair - air box heater components
9-18
C4, TM 9-2350-230-12
Figure 9-15. (Superseded) Removal/installation - air box heater accumulator, coil, and pump
9-19
C4, TM 9-2350-230-12
Figure 9-15.1. (Added) Removal/installation - air box heater accumulator, coil, and pump
(effective vehicle serial no. 62 )
9-20
C4, TM 9-2350-230-12
Figure 9-16. (Superseded) Testing and recharging air box heater accumulator nitrogen pressure
9-20.2
(9-20.1 Blank)
C4, TM 9-2350-230-12
Figure 9-17. (Superseded) Removal/installation - engine fuel filters and elements
9-21
C4, TM 9-2350-230-12
C4, TM 9-2350-230-12
Figure 9-18. (Superseded) Removal/installation/repair - engine fuel system hoses and fittings
9-22
C4, TM 9-2350-230-12
TABLE 9-3. ENGINE FUEL SYSTEM HOSES AND FITTING, FIGURE 9-18
PRELIMINARY STEPS
a. Remove power plant (figure 9-3 through 9-6).
b. Drain fuel tanks (table 5-4).
REMOVAL/INSTALLATION/REPAIR - Replace unserviceable components as required.
ITEM ITEM ITEM ITEM

NO. COMPONENT NO. COMPONENT NO. COMPONENT NO. COMPONENT
1 Pin (4) 18 35 Nipple 51 Nipple

2 Strap (2) 19 Nipple 36 Hose 52 Quick disconnect
3 Clevis pin (4) 20 T Connector 37 Screw 53 Screw
4 Drain hose 20.1 Elbow 38 Clamp 54 Clamp
5 Grommet 21 Elbow 39 Elbow 55 Nut
6 Pump, drain 22 Split coupling 40 Screw 56 Elbow
7 Clamp 23 Nipple 41 Fuel drain bracket 57 Hose
8 Nipple 24 Hose 42 Drain plug 58 Elbow
9 Check valve 25 Clamp 43 Turn buckle (2) 59 Reducer
10 Elbow 26 Screw 44 strap (2) 60 Nipple
11 Check valve 27 Plug 45 Pad (2) 61 Nipple
12 Elbow 28 Valve 46 Elbow 62 Packing
13 Hose 47 Hose 47 Hose 63 Packing
14 Nipple 30 Hose 48 Grommet 64 Plunger assy.
15 Filter 31 Nipple 49 Adapter 65 Pump body
16 Washer 32 Elbow 50 Quick disconnect 66 Fuel tank
17 Screw 33 Nipple mount bracket
34 T Connector
Figure 9-19. (Superseded) Removal/installation - engine fuel pump
9-23
C4, TM 9-2350-230-12
Figure 9-20. (Superseded) Removal/installation - fuel tank shut-off valves
9-24
C1, TM 9-2350-230-12
Figure 9-21. Removal/installation - fuel filler cap assembly and filter
9-25
C10, TM 9-2350-230-12
Figure 9-22. Fuel shut-off control system adjustment
9-26
C10, TM 9-2350-230-12
Figure 9-23.. Removal/installation/repair - fuel shut-off control cable and linkage
9-27
C11, TM 9-2350-230-12
Figure 9-24. Removal/installation - air cleaner, restriction indicator,

air cleaner inlet and outlet elbows
9-28
C 11, TM 9-2350-230-12
Figure 9-24.1. Removal/installation - filter and air cleaner.
9-28. 1
C 11, TM 9-2350-230-12
Figure 9-24.2. Removal/installation - blower assembly and hose.
9-28. 2
C 11, TM .9-2350-230-12
Figure 9-24. 3. Removal/installation - hull wiring harness and leads.
9-28.3
C 11, TM 9-2350-230-12
Figure 9-24.4. Removal/installation - engine wiring harness.
9-28.4
C3, TM9-2350-230-12
WE 11235A |
Figure 9-25. Removal/installation - exhaust manifolds and elbows
9-29
C 11, TM 9-2350-230-12
Figure 9-26. Removal/installation/repair - eyhan8t muffler

and components.
9-30
C4, TM 9-2350-230-1.
WE 11040B
Figure 9-27. (Superseded) Removal/installation - exhaust crossover pipe
9-31
TM 9-2350-230-12
Figure 9-28. Engine coolant system - schematic view
9-32
C3, TM 9-2350-230-12
Figure 9-29. (Superseded) Removal/installation/repair - radiator cooling fan shrouds and

shroud seals
9-33
TM 9-2350-230-12
Figure 9-30. Removal/installation - engine coolant radiator (1 of 2)
9-34
C3, TM 9-2350-230-12
Figure 9-31. Removal/installation - engine coolant radiator (2 of 2)
9-35
C8, TM 9-2350-230-12
Figure 9-32. Removal/installation - radiator coolant fan and pulley
9-36
TM 9-2350-230-12
REMOVAL
1. REMOVE 3 SCREWS AND WASHERS ON FAN DRIVE SHAFT
BEARING RETAINER AND REMOVE FAN ROTOR FROM FAN
STATOR.
2. REMOVE 8 SCREWS AND WASHERS.
NOTE. DO NOT REMOVE 4 SCREWS WHICH ARE

PART OF FAN CLUTCH ASSEMBLY.
3. REMOVE FAN CLUTCH AND RETAINER/BEARING ASSEMBLY
FROM ROTOR. REFER TO SUPPORTING MAINTENANCE FOR
REPAIR OF CLUTCH OR BEARINGS.
INSTALLATION
REVERSE REMOVAL PROCEDURE.
INSTALLATION NOTE. CHECK CLUTCH FLUID LEVEL. AFTER

ABOVE INSTALLATION PLACE FAN ASSEMBLY IN VERTICAL
POSITION. ROTATE DRIVE SHAFT UNTIL FILLER PLUG IS
VISIBLE. ROTATE ROTOR AND SHAFT UNTIL PLUG IS AT 12
O’CLOCK. REMOVE PLUG AND SLOWLY ROTATE ROTOR.
FLUID SHOULD BE VISIBLE AT THE 3:30 O’CLOCK POSITION. IF
REQUIRED ADD DAMPING FLUID-SILICONE BASE, 9150-543-7219
UNTIL FLUID IS VISIBLE AT 3:30 POSITION. CHECK FACE OF
HEAT ELEMENT FOR EVIDENCE OF LEAKAGE.
Figure 9-33. Removal/installation - engine coolant for assembly
PRELIMINARY STEP
OPEN LEFT ENGINE COMPARTMENT GRILLE DOOR.
REMOVE AIR CLEANER-TO-TURBOCHARGER DUCT, FIG. 9-24.
DRAIN COOLANT SYSTEM, TABLE 5-4.
LEGEND
1. CLAMP (2) UPPER
2. NUT AND VENT HOSE
3. HOSE (2) UPPER
4. CLAMP - LOWER
5. HOSE - LOWER
6. CLAMP (2)
7. SURGE TANK
8. SCREW (3), WASHER (3), AND BRACKET
REMOVAL
FOLLOW NUMERICAL SEQUENCE. DO NOT USE
SCREW DRIVER TO REMOVE HOSES.
INSTALLATION
REVERSE NUMERICAL SEQUENCE.
CAUTION: TEST RUN ENGINE AND RETIGHTEN ALL
COOLANT HOSE CLAMPS SECURELY.
COOLANT SYSTEM IS PRESSURIZED WHEN
ENGINE WARMS TO OPERATING TEMPERATURE.
WE 11168
Figure 9-34. Removal/installation - coolant system surge tank
9-37
TM 9-2350-230-12
PRELIMINARY STEPS
A. REMOVE POWER PLANT (FIGS. 9-3 THROUGH 9-6)
B. DRAIN COOLANT SYSTEM
REMOVAL - ENGINE COOLANT BY-PASS TUBE

1. LOOSEN CLAMP FASTENING HOSE TO THERMOSTAT
HOUSING
2. REMOVE 2 SCREWS AND 2 WASHERS FASTENING
ELBOW TO ENGINE.
3. REMOVE TUBE AND ELBOW ASSEMBLY.
NOTE. DO NOT USE SCREWDRIVER TO REMOVE

ANY HOSES ON COOLANT SYSTEM,
INSTALLATION NOTE. USE NEW GASKET BETWEEN
ELBOW AND ENGINE.
REMOVAL - COOLANT OUTLET CROSSOVER TUBE

4. LOOSEN 2 CLAMPS ON WATER PUMP INLET HOSE AND SLIDE HOSE OFF PUMP.
5. LOOSEN CLAMP ON SURGE TANK HOSE AND SLIDE HOSE OFF TUBE.
6. LOOSEN 2 CLAMPS ON COOLANT TUBE MOUNT SUPPORT AND SLIDE OFF BRACKET.
7. LOOSEN 2 CLAMPS ON RADIATOR OUTLET HOSE AND SLIDE HOSE, CLAMP, AND SEAL
ONTO COOLANT TUBE.
NOTE: DO NOT USE SCREWDRIVER TO REMOVE ANY COOLANT HOSE. IT CAN DAMAGE
HOSE OR TUBES.
INSTALLATION
TEST RUN ENGINE TO OPERATING TEMPERATURE AND RETIGHTEN ALL COOLANT HOSE
CLAMPS SECURELY TO PREVENT LEAKS.
WE 10960
Figure 9-35. Removal/installation - engine coolant tubes, hoses, and clamps
9-38
TM 9-2350-230-12
Figure 9-36. Removal/installation - engine coolant pump
9-39
TM 9-2350-230-12
PRELIMINARY STEP
DRAIN ENGINE COOLANT SYSTEM (TABLE 54).
REMOVAL
1. LOOSEN LARGE HOSE CLAMP.
2. LOOSEN SMALL HOSE CLAMPS -SLIDE HOSE
UPWARD ON BYPASS TUBE.
3. SCREW (4), LOCK WASHER (4), FLAT WASHER (4),
HOUSING, AND GASKET.
INSTALLATION
REVERSE REMOVAL SEQUENCE. INSTALL NEW
GASKET AND THERMOSTAT.
LEGEND
1. GASKET
2. THERMOSTAT
3. THERMOSTAT HOUSING
4. BYPASS TUBE
Figure 9-37. Removal/installation - thermostat housing and thermostat
9-40
C6, TM 9-2350-230-12
Figure 9-38. Removal/installation - engine radiator support
9-41
C8, TM 9-2350-230-12
Section 9-3.TRANSMISSION AND CONTROLS
9-11. General c. Refer to table 8-17toperform in-vehicle

stall test. To stall test transmission out-of-
vehicle, refer to support maintenance.
a. This section contains maintenance pro-
cedures for the transmission and transmission d. Fuel shut-off controls are illustrated in
controls. figures 9-22 and 9-23.
b. Refer to paragraph 8-9 to perform trans- e. Fixed fire extinguisher controls are illus-
mission pressure test trated in figures 9-140, 9-141, and 9-142.
TABLE 9-4. TRANSMISSION AND CONTROLS

FIGURE REFERENCE
ASSEMBLY OR COMPONENT SERVICE ADJUST REPLACE REPAIR
Internal Brake 9-39
Oil Filter 9-40 9-40
Oil Level Indicator 9-41
Throttle Control Assembly and Linkage 9-43 9-44 9-45 9-45
Shift Control Assembly and Linkage 9-42 9-47 9-46 9-46
Brake Control Assembly and Linkage 9-43 9-48 9-49 9-50,51
Land Steer Control Assembly and Linkage 9-42 9-53 9-52 9-52
Water Steer Control Assembly and Linkage 9-42 9-55 9-54 9-54
Neutral Safety Switch 9-47 9-100

Water Steer Switch 9-55 9-100
9-42
C9, TM 9-2350-230-12
PRELIMINARY STEP
REMOVE ENGINE ACCESS COVER (FIG. 9-3)
BRAKE CHECK AND ADJUSTMENT

1. REMOVE SNAP RING AND BRAKE LEVER FROM BRAKE
APPLY SHAFT (SPLINED).
2. REMOVE 5 SCREWS, LOCK WASHERS, FLAT WASHERS
AND TRANSMISSION INSPECTION COVER.
3. ADJUST RIGHT AND LEFT BRAKES SEPARATELY, INSTALL
ADAPTER 5120-906-1051 ON BRAKE APPLY SHAFT WITH ½
INCH DRIVE SOCKET WRENCH EXTENSION AND
STANDARD TORQUE WRENCH.
4. APPLY 100 POUND-FEET TORQUE TO BRAKE APPLY SHAFT
(CLOCKWISE ON LEFT BRAKE, COUNTER-CLOCKWISE ON
RIGHT BRAKE). NOTE POSITION OF INDICATOR RELATIVE
TO INDEX DOT ON TRANSMISSION.
5. IF DOT IS BETWEEN “OFF” AND “APPLY”, LOOSEN BRAKE.
IF DOT IS ON “APPLY” OR BETWEEN “APPLY” AND “ADJ.”,
ADJUSTMENT IS SATISFACTORY. IF DOT IS ON “ADJ” OR
BEYOND TIGHTEN BRAKE.
NOTE. LEFT AND RIGHT BRAKES MUST BE ADJUSTED

EQUALLY.
6. TO ADJUST, LOOSEN LOCK NUT. TO LOOSEN BRAKE,

TURN SCREW COUNTERCLOCKWISE (OUT). TO TIGHTEN
BRAKE, TURN SCREW CLOCKWISE (IN). TIGHTEN LOCK
NUT AFTER ADJUSTMENT,
7. RECHECK ADJUSTMENT WITH TORQUE WRENCH.
8. WHEN BOTH BRAKES HAVE BEEN ADJUSTED, APPLY
BRAKES AND CHECK INDICATORS. INDICATOR READINGS
SHOULD BE APPROXIMATELY SAME ON BOTH BRAKES.
9. INSTALL ITEMS REMOVED OR DISCONNECTED IN STEPS 1,
2, 3 AND 4.
D. BRAKE INDICATOR - REFERENCE LEFT

SHOWN - RIGHT OPPOSITE.
WE 66614
Figure 9-39. Transmission internal brake adjustment
9-43
C9, TM 9-2350-230-12
Figure 9-40. Removal/service/installation - transmission oil filter
Figure 9-41. Installation - transmission dipstick, seal, and gasket
9-44
C8, TM 9-2350-230-12
LAND AND WATER STEER CONTROLS

(FIGURES 9-52 AND 9-54)
SHIFT, FUEL SHUT-OFF, AND FIXED FIRE EXTINGUISHER CONTROLS

(FIGURES 9-46, 9-23. AND 9-141)
WE 12136
Figure 9-42. Land and water steer, shift, fuel shutoff, and fixed fire
extinguisher controls - locational reference
9-45
C8, TM 9-2350-230-12
THROTTLE CONTROL
(FIGURE 9-45)
BRAKE CONTROL
(FIGURES 9-49 AND 9-50)
Figure 9-43. Throttle and brake controls - locational reference
9-46
C8, TM 9-2350-230-12
Figure 9-43.1. Control adjustment locational reference
9-46.1
C8, TM 9-2350-230-12
Figure 9-44. Accelerator/throttle control and linkage adjustment (1 of 2)
9-46.2
C8, TM 9-2350-230-12
Figure 9-44.1. Accelerator/throttle control and linkage adjustment (2 of 2)
9-47
C8, TM 9-2350-230-12
Figure 9-45. Disassembly/assembly - accelerator and throttle control assembly and linkage (1 of2)
9-48
C8, TM 9-2350-230-12
Figure 9-45.1. Disassembly/assembly - accelerator and throttle control assembly and linkage (2of2)
Table 9-4.1 - Deleted
9-49
C8, TM 9-2350-230-12
Figure 9-46. Removal/installation/repair - transmission shift control assembly

and linkage
9-50
C8, TM 9-2350-230-12
TABLE 9-5. REMOVAL/INSTALLATION - TRANSMISSION SHIFT CONTROL

ASSEMBLY AND LINKAGE (FIGURE 9-46)
PRELIMINARY STEPS
A. Open engine exhaust grilles and remove engine access cover (fig. 9-3, steps 3 through 5). Place wooden block
approximately 2-1/2 inches thick on engine step plate under grille support. If access to bulkhead is required, also
remove intake grille (fig. 9-3, step 1).
B. Remove vehicle batteries (fig. 9-97).
C. Remove four screws, three washers, and protective plate from battery compartment (fig. 9-45. 1, item 3).
D. Remove two screws, washers, and protective plate from control cable support at transmission (fig. 9-4, item 12).
E. Review control cable handling precautions, table 9-9. 1.
REMOVAL (Refer to figure 9-46 for item reference numbers.)
1. Remove cotter pin (1) and clevis pin (2) from clevis (3) at driver’s shift lever (13) and transmission shift lever (10).
2. Loosen jam nut and remove clevis (3) and jam nut (4) from both ends of control. Loosen and remove control
assembly jam nuts (6) at mounting bracket in driver’s compartment and control support at the transmission.
Remove two grommets (7) and retaining straps along right side of hull (fig. 9-42).
3. Remove control out through engine compartment. Handle control assembly by outer casing and not by inner
race rod.
INSTALLATION NOTE. Inspect seals and replace if deteriorated.
4. Install control cable through the vehicle from engine compartment.
5. Place jam nuts (4) and clevis (3) on control rod ends. Do not twist center race rod.
6. Install grommet (7) and retaining straps (fig. 9-42).
7. Install jam nuts (6) and position control assembly in mounting brackets. Do not tighten.
8. Install jam nut (4) and clevis (3) with approximately 3/8-inch thread engagement on both ends of the control
assembly.
9. Attach clevis to driver’s shift lever (13) with clevis pin (2) and cotter pin (1).
10. Position driver’s shift lever in “N” (Neutral) position and install 1/8-inch dia. pin in pad provided (fig. 9-47). Place
transmission shift lever (10) in “N” position.
11. Late design control cable - Adjust control assembly, using jam nuts (6) at mounting bracket in driver’s
compartment, to obtain measurement of 1/8 + 1/16 inch from control cable tube to clevis jam nut (fig. 9-47).
11A. Early design control cable - Adjust control assembly, using jam nuts (6) at mounting bracket in driver’s
compartment, to obtain a measurement of 2 inches from control assembly wiper-seal to threads on the race rod.
(See inset, fig. 9-47).
12. Adjust control assembly jam nuts at transmission control support bracket to provide a free pin fit at transmission
shift lever.
13. Remove 1/8-inch dia. pin from quadrant. Clevis pin at transmission lever should fit freely in all shift positions.
Install clevis pin (2) and cotter pin (1).
9-51
C8, TM 9-2350-230-12
Figure 9-47. Transmission shift control and linkage adjustment
9-52
C8, TM 9-2350-230-12
TABLE 9-5.1. TRANSMISSION SHIFT CONTROL AND LINKAGE ADJUSTMENT (FIGURE 9-47)
PRELIMINARY STEPS
A. Open engine exhaust grilles and remove engine access cover (Figure 9-3, step 3 through 5). Place wooden
block approximately 2-1/2 inches thick on engine step plate under grille support. If access to bulkhead is
required, also remove intake grille (Fig. 9-3, step 1).
B. Remove vehicle batteries (Fig. 9-97).
C. Remove two screws, washers and protective plate from transmission control cable support (Figure 9-4, item 12).
D. Review control cable handling precautions, table 9-9. 1.
TRANSMISSION SHIFT CONTROL ADJUSTMENT
1. At transmission, remove cotter pin and clevis pin and disconnect shift linkage from shift lever.
2. Move driver’s shift control to any drive range then back to “N” (NEUTRAL) position.
3. Align hole in driver’s shift control with hole in pad on shift quadrant. Insert a 1/8-inch dia. pin in hole provided to
retain shift lever in “N” position (see Figure 9-47).
4. Adjust late design control assembly by using jam nuts at mounting bracket in driver’s compartment, to obtain
measurement of 1/8 41/16 inch from control cable tube to clevis jam nut.
4A. Adjust early design control assembly by using jam nuts at mounting bracket in driver’s compartment to obtain a
measurement of 2 inches from control assembly wiper-seal to threads on race rod.
5. Move shift lever on transmission (by hand) to “N” (NEUTRAL) position as indicated by selector indicator on
transmission.
6. At transmission control support bracket, adjust control assembly jam nuts to provide a free pin fit at transmission
shift lever.
7. Remove 1/8-inch dia. pin from quadrant, operate driver’s shift control in all positions and check for proper
synchronization between driver’s and transmission shift levers (clevis pin at transmission shift lever should fit
freely in all shift positions). (Replace cotter pin).
NEUTRAL SAFETY SWITCH ADJUSTMENT
8. Perform step 3,
9. Loosen two neutral safety switch mounting screws.
10. Position switch so that roller is in center of heel of lever and is depressed sufficiently to actuate switch (switch
closed). Tighten mounting screws.
11. Remove 1/8-inch dia, pin, set parking brake and start engine to check proper operation of switch. Attempt to start
engine with driver’s shift control in other than “N” (NEUTRAL) position. If switch is adjusted correctly the engine
starter will not activate.
9-52.1
C8, TM 9-2350-230-12
Figure 9-48. Brake control and linkage adjustment (1 of 2)
9-52.2
C8, TM 9-2350-230-12
Figure 9-48.1. Brake control and linkage adjustment (2 of 2)
9-53
TM 9-2350-230-12
Figure 9-49. Removal/installation/adjustment - parking brake assembly
9-54
C6, TM 9-2350-230-12
Figure 9-50. Removal/installation/repair - brake control cables and linkage (1 of 2)
9-55
TM 9-2350-230-12
REFER TO TABLE 9-6 FOR LEGEND

REFER TO FIGURE 9-43 - THROTTLE AND BRAKE CONTROL LOCATIONAL REFERENCE.
REFER TO FIGURE 9-39 - TRANSMISSION INTERNAL BRAKE ADJUSTMENT.
REFER TO FIGURE 9-49 - PARKING BRAKE AND WARNING LIGHT SWITCH ADJUSTMENT.
REFER TO FIGURE 9-48 - BRAKE CONTROL CABLE, LINKAGE, AND STOPLIGHT SWITCH ADJUSTMENT.
Figure 9-51. Removal/installation/repair - brake control cables and linkage (2 of 2)
9-56
C8, TM 9-2350-230-12
TABLE 9-6. LEGEND FOR FIGURES 9-50 AND 9-51
ITEM ITEM ITEM

NO. DESCRIPTION NO. DESCRIPTION NO. DESCRIPTION
1 CotterPin (17) 28 Pulley (6) 55 Clevis Pin (2)
2 Clevis Pin (6) 29 Bracket 56 Clevis
3 Screw (4) 30 Spacer 57 Clevis Pin
4 Flat Washer (4) 31 Retainer 58 Rod End Bearing
5 Nut (3) 32 Clevis 59 Pulley
6 Flat Washer (3) 33 Jam Nut 60 Wire Rope Assy.
7 Jam Nut (2) 34 Wire Rope Assy 61 Equalizer Plate
8 Stoplight Switch 35 Clevis Pin 62 Spring
9 Bracket 36 Clamp (2) 63 Cotter Pin (2)
10 Bearing (2) 37 Clamp (2) 64 Washer (2)
11 Bracket 38 Bushing (2) 65 Washer (2)
12 Screw 39 Bellows (2) 66 Bearing (2)
13 Flat Washer (2) 40 Clevis Pin 67 Bearing (2)
14 Nut 41 Turnbuckle 68 Cam Lever, Left
15 Dowel Pin 42 Jam Nut (2) 69 Cam Lever, Right
16 Pedal 43 Wire Rope Assy 70 Screw (6)
17 Clevis Pin 44 Wire Rope Assy 71 Flat Washer (6)
18 Bearing (2) 45 Clevis Pin 72 Jam Nut (2)
19 Flat Washer (2) 46 Nut (4) 73 Screw (2)
20 Rod End Bearing 47 Screw (4) 74 Cam Lever Bracket, Right
21 Jam Nut 48 Plate (4) 75 Cam Lever Bracket, Left
22 Clevis 49 Bracket 76 Cotter Pin (2)
23 Screw (2) 50 Cotter Pin (2) 77 Clevis Pin (2)
24 Bracket 51 Clevis Pin (2) 78 Bearing (2)
25 Screw (3) 52 Clevis (2) 79 Brake Apply Lever, Right
26 Flat Washer (3) 53 Clevis Pin (4) 80 Brake Apply Lever, Left
27 Retainer(3) 54 Wire Rope Assy.
9-57
C8, TM 9-2350-230-12
Figure 9-52. Disassembly/assembly/repair - land steer control cable and linkage
9-58
C8, TM 9-2350-230-12
TABLE 9-7. REMOVAL/INSTALLATION/REPAIR - LAND STEER CONTROL CABLE AND LINKAGE
(Refer to figure 9-52 for preliminary steps and item reference numbers)
REMOVAL
1. Review control cable handling precautions, table 9-9. 1.

2. Remove cotter pin (13), clevis pin (14) and bearing (2) from transmission steer lever.
3. Hold control rod end and loosen jam nut (4). Remove coupling-tube-rod bearing assembly (6, 4, 12, 4, 2) and
jam nut (4) from control assembly.
4. Hold cable housing and remove seal assembly (7), two jam nuts (8), and two washers (9).
5. Remove two grommets (10), and retaining straps.
6. In driver’s compartment, remove nut (3) and screw (1).
7. Hold control rod end to prevent twisting and loosen coupling jam nut (4). Remove coupling assembly (6, 4, 5, 4,
2) and jam nut (4)°
8. Remove seal nut (7). Hold control housing and loosen jam nuts (8) at the hull mounting bracket. Remove outer
jam nut (8) and washer (9).
9. Remove control assembly (11) from mounting bracket and remove second washer (9) and jam nut (8). Avoid
unnecessary force and sharp bends by sliding control assembly to rear of vehicle. Do Not Twist Control
Cable.
10. Remove control assembly (11) through engine compartment holding control assembly by the outer housing. Do
not lift or handle control assembly by rod ends.
INSTALLATION
1. Review step 1 above.
2. Assemble a steer bar coupling assembly as follows:
a. Screw jam nut (4) on bearing (2). Leave ½” of threads.
b. Screw long (7-3/16”) tube (5) onto bearing.
c. Screw jam nut (4) onto coupling (6) - leave ½” of threads.
d. Screw coupling (6) into tube (5).
3. Assemble a transmission steer control coupling the same as step 2 above except use a short (6-3/8”) tube (12).
4. From engine compartment, thread control through battery compartment rear bulkhead and engine compartment
bulkhead. Install grommets (10)o
5. From crew compartment place control assembly along right slope plate to front of driver’s compartment. See
figure 9-42.
6. Install jam nut (8) and washer (9) on control assembly (11). Leave 2” of thread on end of control assembly.
7. Install control assembly through hull mounting bracket (23) eye and install washer (9), nut (8), and seal assembly
(7). Do not tighten jam nuts (8). Stroke control rod several times to permit internal components to position
themselves. Control should operate freely.
8. Install jam nut (4) onto control rod - leave ½” of threads.
9. Install long coupling assembly (6, 4, 5, 4, 2)° Hold control rod from twisting.
10. Attach control to T-bar with screw (1) and nut (3).
11. Using improvised tool as shown in figure 9-53. 1, position and tighten jam nuts.
12. Operate T-bar to assure equal motion of steer control lever to both left and right side.
13. Install cable retaining straps, figure 9-42.
14. In engine compartment, install jam nut (8), two washers (9), and 2nd jam nut (8) on cable housing. Leave 1” of
threads to first lock nut and ½” between washers. Install rear seal assembly (7).
15. Install jam nut (4) on control rod -leave ½” of threads.
16. Install rear (short) coupling assembly (6, 4, 12, 4, 2).
17. Place control assembly (11) in rear slot of transmission cable support bracket.
18. Operate T-bar several times to permit internal components to position themselves. Position control assembly in
transmission cable support bracket.
19. Adjust linkage (figure 9-53).
9-59
C8, TM 9-2350-230-12
Figure 9-53. Land steer control cable and linkage adjustment (1 of 2)
9-60
C8, TM 9-2350-230-12
Figure 9-53.1. Land steer control cable and linkage adjustment (2 of 2)
9-61
C8, TM 9-2350-230-12
Figure 9-54. Disassembly/assembly/repair - water steer control cable and linkage
9-62
C8, TM 9-2350-230-12
TABLE 9-8. REMOVAL/INSTALLATION/REPAIR - WATER STEER
CONTROL CABLE AND LINKAGE
PRELIMINARY STEPS
A. Open engine exhaust grilles and remove engine access cover (Fig. 9-3, steps 3 through 5). Place wooden block
approximately 2-1/2 inches thick on engine step plate under grille support. If access to bulkhead is required, also
remove intake grille (Fig. 9-3, step 1).
B. Remove vehicle batteries (Figure 9-97).
C. Remove four screws, three washers, and protective plate from battery compartment (Figure 9-45.1, item 3), D.
Remove two screws, washers, and protective plate from control cable support at transmission (Figure 9-4, item
12).
E. Review control cable handling precautions, table 9-9. 1.
CABLE REMOVAL (Refer to Figure 9-54 for item reference numbers. )

1. Remove nut (1), washer (2), and switch actuator (3). Remove nut (4), knob (5), and pin (6) as an assembly.
2. Remove two nuts (21), two washers (2) and rear bearing (22) and remove rod (7) from control cable assembly.
Loosen jam nuts (8) retaining control cable in support bracket (20) on control support plate (25).
3. Remove cotter pin (10) and clevis pin (11) from transmission water steer lever (18).
4. Loosen jam nut (8) and remove cable assembly from transmission control cable support bracket.
5. Loosen jam nut (12) and remove bearing (13), jam nuts (12) and connector (14) from cable assembly.
6. Remove jam nuts (8) and flat washers (9) from both ends of cable assembly. Remove grommets (15) from cable
and bulkheads. Remove retaining straps along right side of null (Refer to Figure 9-42).
7. Remove control cable (16) out through engine compartment. Handle control assembly by outer casing and not by
race rod or inner cable.
CABLE INSTALLATION
Follow steps 7 through 1. Refer to Figure 9-55 for adjustment of control cable.
TABLE 9-9. LEGEND FOR FIGURE 9-54
1. Jam nut 10. Pin, cotter 180 Water steer lever

2. Flat Washer (8) 11. Pin, clevis 19. Screw (2)
3. Switch actuator 12. Jam nut (2) 20. Bracket
4. Nut 13. Rod end bearing 21. Nut (4)
5. Knob 14. Connector 22. Bearing (2)
6. Pin 15. Grommet (2) 23. Screw (2)
7. Rod 16. Control cable assembly 24. Switch assembly
8. Jam nut (4) 17. Screw 25. Control support plate
9. Flat washer (4)
9-63
C8, TM 9-2350-230-12
Figure 9-55. Water steer control cable and linkage adjustment
9-64
C8, TM 9-2350-230-12
Figure 9-56 Deleted
Figure 9-57 Deleted
Figure 9-58 Deleted
TABLE 9-9.1. CONTROL CABLE HANDLING PRECAUTIONS
DESCRIPTION
Control cables are precision control devices for transmitting push-pull movement. Because they are precision controls,
precautions must be observed in their handling and installation if they are to function properly.
HANDLING PRECAUTIONS
Handle the assembly by outer housing only and not by rod ends.
Use care when tightening outer housing jam nuts to avoid twisting housing.
Use wrench on end rod flats whenever tightening or loosening jam nut or coupling to prevent twisting the inner core.
The control is quite flexible in one plane but when making a bend into another plane the control must be gently formed into
position to give the internal parts a chance to adjust for the new direction. Tapping lightly with the hand or a rawhide mallet
will help the internal parts to align themselves.
Before connecting the control ends, stroke control several times to allow the internal components to align themselves.
Do not use force or bend sharply, but form easily into position.
NOTE. 1. Store stock controls in standard figure 8 coils, preferably in their containers as received. If unpacked,
hang on wall.
2. Do not attempt to force oil into the control.
3. Thread engagement at bearing, coupling, or center control rod should be at least 3/84nch for strength
and safety.
4. Keep jam nuts tight at all times to prevent vibration and wear.
9-65
C10, TM 9-2350-230-12
Section 9-4. TRACKS AND SUSPENSION
9-12. General c. Periodic lubrication will be in accordance with LO

9-2350-230-12. Assembly/installation instructions will
specify additional lubrication procedures required in
a. This section contains organizational maintenance conjunction with assembly/installation.
instructions for the vehicle suspension system as shown
in figures 9-59, 9-60, and table 9-10 d. Whenever plugs are used in suspension
lubrication system, use only hardened hex recessed
b. All two-piece bearings (cup and cone)are supplied head plugs, FSN 4730-278-3462. The correct plugs are
only in matched sets. identified by embossed or raised markings radiation from
corners of hex recess.
TABLE 9-10. TRACKS AND SUSPENSION
FIGURE REFERENCE
REMOVE
ASSEMBLY OR COMPONENT INSTALL REPLACE REPAIR
Road Wheels 9-61

Torsion Bar and Road Wheel Arm Assembly 9-62
Torsion Bar Anchors 9-63
Road Wheel Spindle 9-64
Position No. 2 and No. 3 Road Wheel Arm 9-65 9-65
Housing and Shaft Assembly
Position No. 1, 4, and 5 Road Wheel Arm 9-66 9-66
Housing and Shaft Assembly
Track Hydraulic Adjuster and Bracket 9-67
Track Idler Wheels 9-68
Idler Hub Assembly 9-69
Idler Housing and Spindle Assembly 9-70 9-70
Sprocket Drive Shaft 9-71
Sprocket and Sprocket Carrier Wheels 9-72
Sprocket Hub and Support 9-73 9-73
Shock Absorber and Mounting Bracket 9-74
Suspension System Seal Installation Specifications 9-75
Suspension System Special Tools (1 of 4) 9-76
Suspension System Special Tools (1. 1 of 4) 9-76.1
Track Shoe 9-80
Replacing Damaged Track Shoe 9-81
9-66
C 10, TM 9-2350-230-12
Figure 9-59. Vehicle suspension system
9-67
C10. TM 9-2350-230-12
TORSION BAR, ANCHOR, AND ROAD WHEEL ARM AND SHAFT ASSEMBLY IDENFICATION CHART
ITEM VEHICLE POSITION TORSION BAR IDENTIFYING MATING LOCATION OF ROAD WHEEL
(FIG. 9-59) PART NUMBER ARROW ANCHOR BLIND SPLINE ARM ASSEMBLY
(PRESET) (ON IN ANCHOR* PART NUMBER
OPPOSITE
SIDE OF
VEHICLE)
PART
NUMBER
RIGHT SIDE
(1) FRONT 10948666-2 10948664-1 APPROX 10954288-2
7:30 O’CLOCK
(2) FRONT 10948665-2 10948664-4 APPROX 10954286
INTERMEDIATE 7:30 O’CLOCK
(3) INTERMEDIATE 10948665-1 10948664-3 APPROX 10954286
4:30 O’CLOCK
(4) REAR 10948666-2 10948664-4 APPROX 11593592
(5) REAR 10948666-2 10948664-4 APPROX 10954288-2
7:30 O’CLOCK
LEFT SIDE
(1) FRONT 10948666-1 10948664-2 APPROX 10954288-1
4:30 O’CLOCK
(2) FRONT 10948665-1 10948664-3 APPROX 10954286
(3) INTERMEDIATE 10948665-2 10948664-4 APPROX 10954286
7:30 O’CLOCK
(4) REAR 10948666-1 1094664-3 APPROX 11593592
(5) REAR 10948666-1 10948664-3 APPROX 10954288-1
4:30 O’CLOCK
*AS VIEWED THROUGH VEHICLE FROM ROAD WHEEL ARM SIDE.
WE 66667
Figure 9-60. Vehicle suspension system component identification
Page 9-68.1 including figure 9-60.1 - deleted.
9-68
C10, TM 9-2350-230-12
Figure 9-61. Removal/installation - road wheels
9-69
C11, TM 92350-230-12
Figure 9-62. Removal/installation - torsion bar and road wheel arm assembly
9-70
C10, TM 9-2350-230-12
Figure 9-63. Removal/installation - torsion bar anchors
9-71
C10, TM 9-2350-230-12
Figure 9-64. Disassembly/assembly - road wheel arm spindle
9-72
C10, TM 9-2350-230-12
Figure 9-65. Disassembly/assembly position no. 2 and no. 3 road wheel arm housing and shaft assembly
9-73
C10, TM 9-2350-230-12
Figure 9-66. Disassembly/assembly position no. 1, no. 4 and no. 5 road wheel arm housing and shaft assembly
9-74
C6, TM 9-2350-230-12
Figure 9-67. Removal/installation - track hydraulic adjuster and bracket
9-75
C6, TM 9-2350-230-12
Figure 9-68. Removal/installation - track idler wheels.
9-76
C10, TM 9-2350-230-12
Figure 9-69. Removal/installation - idler hub assembly
9-77
C10, TM 9-2350-230-12
Figure 9-70. Removal/disassembly/assembly/installation - idler housing and spindle assembly
9-78
C10, TM 9-2350-230-12
PRELIMINARY STEP
IF VEHICLE IS OPERABLE, START AND MOVE VEHICLE ENOUGH TO ALLOW IT TO COAST TO A STOP
A. REMOVE SCREWS, FLAT WASHERS,

COVER, AND SPRING.
Figure 9-71. Removal/installation - sprocket drive shaft
9-79
C9, TM 9-2350-230-12
Figure 9-72. Removal/installation - sprocket and sprocket career wheels
9-80
C10, TM 9-2350-230-12
Figure 9-73. Removal/disassembly/assembly/installation sprocket hub and support
9-81
C10, TM 9-2350-230-12
Figure 9-74. Removal/installation - shock absorber and mounting bracket
9-82
C10, TM 9-2350-230-12
Figure 9-75. Suspension system seal installation specifications
9-83
TM 9-2350-230-12
Figure 9-76. Suspension system special tools (1 of 4)
9-84
C 11, TM 9-2350-230-12
Figure 9-76. 1. Suspension system special tools (1.1 of 4),
(9-84. 2 blank)/9-84. 1
TM 9-2350-230-12
Figure 9-77. suspension system Special tools (2 of 4)
9-85
TM 9-2350.230-12-
9-86
TM 9-2350-230-12
9-87
TM 9-2350-230-12
Figure 9-80. Removal-track shoe
9-88
C11, TM 9-2350-230-12
Figure 9-81. Replacing damaged track shoe(s).
9-89
C 11, TM 9-2350-230-12
Section 9-5. HULL AND POWER PLANT ELECTRICAL
9-13. General b. Each electrical cable is marked with a circuit-

numbered metal tag attached to the junction or terminal
a. This section covers organizational maintenance end of the cable. All electrical circuits, shown in
functions on hull and power plant lectrical components schematic and wiring diagrams, are identified by circuit
listed in table 9-11. Front and rear hull schematic numbers listed in table 9-12.
diagrams are illustrated in figures 9-84 and 9-85. Hull
and power plant electrical harness diagrams are CAUTION: Turn master switch off before
illustrated in figures 9-82 and 9-83. disconnecting or connecting electrical connectors to
avoid possible arcing.
TABLE 9-11. HULL AND POWER PLANT ELECTRICAL
FIGURE REFERENCE
ASSEMBLY OR COMPONENT
ADJUST REPLACE REPAIR
Headlights 9-86 9-87

thru
9-91
Taillights 9-92,93
Headlight Dimmer Switch 9-94
Dome Light 9-95 9-96
Batteries 9-97
Auxiliary Power (Slave) Receptacle 9-94
Master Relay 9-98
Hull Circuit Breaker 9-100
Driver’s Switch Panel 9-101 9-102,
thru
9-105
Driver’s Switch Panel Rectifier 9-103.1
Time Delay Assembly 9-103. 2
Turret Master Relay 9-103. 3
Electrical Harnesses 9-103. 4,
9-103.5
Driver’s Indicator Panel 9-106
Personnel Heater Control Box 9-107 9-107
Neutral Safety Switch 9-47 9-100
Water Steer Switch 9-54 9-100
Bilge Pump Relays and Mount 9-108
"V" Belt Tensioner and Belts 9-109
Generator Voltage Regulator 9-110.1 9-110,
9-110.1 9-110. 1
Generator Drive and Pulley 9-111,
9-112
Generator-to-Voltage Regulator 9-112.1 9-112.1
Wiring Harness
Engine Starter 9-113
Starter Relay 9-100
Power Plant Temperature and Pressure Switches 9-114
and Transmitters
9-90
C8, TM 9-2350-230-12
TABLE 9-11. HULL AND POWER PLANT ELECTRICAL - CONTINUED
FIGURE REFERENCE
ADJUST REPLACE REPAIR
Tachometer and Speedometer Generators and Drives 9-115 9-116

Fuel Level Transmitters 9-99
Electrical Cable Terminals and Connectors 9-117
Electrical Harness Plugs 9-118
Electrical Harness Receptacle Connectors 9-118
TABLE 9-12. HULL ELECTRICAL CIRCUIT NUMBER REFERENCE CHART
CIRCUIT CIRCUIT
NUMBER
10 Battery ground
11 Battery-to-master relay
12 Master relay-to-master switch
12B Battery-to-master switch
12L Master switch warning light
13 Battery-to-voltage regulator
14 Voltage regulator-to-generator armature
15 Voltage regulator-to-generator field
21 Power circuit-to-starter
22 Neutral safety switch - starter relay
22A Neutral safety switch - starter switch
22A Power circuit-to-starter relay
22B Power circuit-to-starter relay solenoid
30 Upper fuel level transmitter - ground
31A Circuit breaker-to-windshield wiper switch and engine starter relay switch
31B Circuit breaker-to-bilge pump switch and flame heater switch
31C Circuit breaker-to-engine indicator panel
32A Upper fuel level transmitter-to-engine indicator panel
32B Upper fuel level transmitter-to-lower fuel level transmitter
32C Lower fuel level transmitter-to-engine indicator panel (through fuse)
34 Engine coolant transmitter-to-engine indicator panel
39 Engine coolant high temperature thermostatic switch-to-engine indicator panel
40 Headlight ground
41 Power circuit-main light switch
42 Light switch-to-service taillight
43 Light switch-to-B.O. marker taillight
44 Light switch-to-service stoplight
45 Light switch-to-B.O. stoplight
48 Light switch-to-B.O. marker headlight
50 Wiper assembly-to-ground
50A Water steer switch - engine indicator panel warning light
50B Parking brake "ON" switch-to-engine indicator panel warning light
50G Parking brake "ON" switch-to-ground
55 Circuit breaker-to-auxiliary outlet
57 Power lead to driver’s periscope (M48)
70 Slave receptacle negative-to-ground
9-91
C11, TM 9-2350-230-12
TABLE 9-12. HULL ELECTRICAL CIRCUIT NUMBER REFERENCE CHART - CONTINUED
CIRCUIT CIRCUIT
NUMBER
71 Power circuit-to-slave receptacle positive

75 Flame heater switch-to-flame heater ignition coil and fuel solenoid
111 Master relay-to-power circuit
112 Battery interconnecting cable - positive-to-negative
152 Voltage regulator-to-generator interpole
313 Engine lo-oil pressure switch-to-engine indicator panel
314 Transmission oil high temperature thermostatic switch-to-engine indicator
panel
315 Transmission lo-oil pressure switch-to-engine indicator panel
322 TACHOMETER GENERATOR-TO-ENGINE INDICATOR PANEL.
323 Speedometer switch-to-speedometer generator and engine indicator panel
323C Odometer switch-to-engine indicator panel
422 Light switch-to-LR./B. O. headlight selector switch
422A LR./B.O. switch-to-B.O. drive headlight
423 Light switch-to-stoplight switch
424 Light switch-to-headlight dimmer switch - service drive
425 Headlight dimmer switch-to-high beam service headlight
426 Headlight dimmer switch-to-low beam service headlight
427 L R. /B. 0. high beam headlight switch-to-headlight dimmer switch and L R. /B. O.
high beam headlight
427L I.R. warning light
428 LR./B.O. low beam headlight switch-to-headlight dimmer switch and LR./B.O.
low beam headlight
428L I.R. warning light
429 Headlight dimmer switch-to-engine indicator panel - high beam indicator light
432 Circuit breaker-to-dome lights
432A Light switch-to-panel light on engine indicator panel - driver’s switch panel
521 Windshield wiper switch-to-windshield wiper
521B Circuit breaker-to-windshield wiper
521L Windshield wiper warning light
560 Personnel heater-to-ground
561 Battery-to-heater control box (personnel and winterization kit)
562 Heater control-to-coil and flame detector switch
563 Heater control-to-coolant thermostat and solenoid valve
563A Heater control-to-fuel pump
564 Heater control-to-blower motor
565 Heater control-to-flame detector switch
721 Bilge pump switch-to-bilge pump relay
721B Rear bilge pump relay
721BL Rear bilge pump indicator light
721L Front bilge pump indicator light
722 Power circuit-to-bilge pump relay (rear bilge pumps)
722A Bilge pump relay-to-circuit breaker (rear bilge pumps)
722B Circuit breaker - left rear bilge pump
722C Circuit breaker - right rear bilge pump
723 Power circuit-to-bilge pump relay (front bilge pump)
723A Bilge pump relay-to-circuit breaker (front bilge pump)
723B Circuit breaker-to-front bilge pump
9-92
C11, TM 9-2350-230-12
TABLE 9-12. HULL ELECTRICAL CIRCUIT NUMBER REFERENCE CHART - CONTINUED
CIRCUIT CIRCUIT
NUMBER
11T MASTER RELAY-TO-TURRET POWER RELAY.
12C STARTER SWITCH-TO-RECTIFIER.
12T TIME DELAY-TO-TURRET POWER RELAY.
22T TIME DELAY-TO-STARTER SWITCH.
23 B. O. STOPLIGHT LEAD, RIGHT.
24 B. O. MARKER TAILLIGHT, LEFT AND RIGHT.
50 AIR CLEANER BLOWER MOTOR RELAY-TO-RELAY SWITCH..
58 BLOWER MOTOR-TO-RELAY.
58A BLOWER MOTOR-TO-RELAY.
111T TURRET POWER RELAY-TO-SLIPRING.
322A TACHOMETER SWITCH-TO-ENGINE INDICATOR PANEL.
581 STARTER RELAY-TO-BLOWER MOTOR RELAY.
720 FIRE EXTINGUISHER SOLENOID-TO-GROUND.
725 FIRE EXTINGUISHER SOLENOID-TO-SLIPRING.
726 TURRET POWER RELAY-TO-SLIPRING.
(9-92. 2 blank)/9-92.1
C11, TM 9-2350-230-12
Figure 9-82. Hull electrical wiring diagram.
9-93
C11, TM 9-2350-230-12
Figure 9-83. Power plant electrical wiring diagram.
9-94
C11, TM 9-2350-230-12
Figure 9-84. Hull electrical schematic (1 of 2)

C11, TM 9-2350-230-12
Figure 9-85. Hull electrical schematic (2 of 2).

C6, TM 9-2350-230-12
Figure 9-86. Headlight adjustment and beam alignment procedure
9-95
C9, TM 9-2350-230-12
Figure 9-87. Headlight wiring diagram
Figure 9-88. Disassembly/assembly - headlight assembly and components (1 of 4)
9-96
C9, TM 9-2350-230-12
9-97
C9, TM 9-2350-230-12
9-98
C9, TM 9-2350-230-12
9-99
TM 9-2350-230-12
Figure 9-92. Disassembly/assembly - taillights (1 of 2)
9-100
TM 9-2350-230-12
Figure 9-93. Disassembly/assembly - taillights (2 of 2)
9-101
TM 92350-230-12
REMOVAL
FOLLOW NUMERICAL SEQUENCE.
1. HEADLIGHT HARNESS PLUG NUT.
2. DIMMER SWITCH ATTACHING SCREWS AND

FLAT WASHERS.
3. HEADLIGHT DIMMER SWITCH.
INSTALLATION
REVERSE NUMERICAL SEQUENCE.

A. HEADLIGHT DIMMER SWITCH INSTALLED VIEW.
B. AUXILIARY POWER (SLAVE) RECEPTACLE INSTALLED VIEW.
REMOVAL
REMOVE SCREWS, FLAT WASHERS, AND NUTS; SLIDE RECEPTACLE TO LEFT TO REMOVE FROM BRACKET. IF
PINS REQUIRE REPLACEMENT, UNSOLDER CABLE FROM PIN.
INSTALLATION
REVERSE REMOVAL PROCEDURE. WE 11085
Figure 9-94. Removal/installation headlight dimmer switch and auxiliary power (slave) receptacle
9-102
C6. TM 9-2350-230-12
DRIVER ‘S DOME LIGHT TYPICAL TURRET DOME LIGHT

1. DISCONNECT ELECTRICAL CONNECTORS. REVERSE REMOVAL PROCEDURE.
2. REMOVE TWO NUTS AND / OR SCREWS REMOVE ALL PAINT AT ONE CORNER TO PROVIDE
AND WASHERS TO REMOVE DIMMER GOOD GROUND. (SEE FIG. 9-95.1 FOR INSULATION
SWITCH W/BRACKET. REQUIRED ON DIMMER SWITCH AT LOADER’S
3. REMOVE OTHERS TWO NUTS AND/OR STATION.)
SCREWS AND WASHERS TO REMOVE
DOME LIGHT ASSEMBLY
Figure 9-95.1. Disassembly/assembly - dome light dimmer switch.
9-103
C6, TM 9-2350-230-12
Figure 9-96. Disassembly/assembly - dome lights
9-104
C9, TM 9-2350-230-12
Figure 9-97. Removal/installation - batteries and leads
9-105
C4, TM 9-2350-230-12
Figure 9-98. Removal/installation - master relay
Figure 9-99. Removal/installation - fuel level transmitters
9-106
C 11, TM 9-2350-230-12
Figure 9-100. Removal/installation starter relay, neutral safety and water steer switches, and hull circuit breakers
9-107
C11, TM 9-2350-230-12
Figure 9-101. Removal/installation - driver’s switch panel
9-108
TM 9-2350-230-12
Figure 9-102. Disassembly/assembly - driver’s stitch panel (1 of 2)
9-109
C3 TM 9-2350-230-12
Figure 9-103. (Superseded) Disassembly/assembly - driver’s switch panel (2 of 2)
9-110
C 11, TM 9-2350-230-12
Figure 9-103.1. Removal/installation - driver’s switch panel rectifier.
9-110.1
C 11, TM 9-2350-230-12
Figure 9-103.2. Removal/installation - time delay assembly.
9-110.2
C 11, TM 9-2350-230-12
Figure 9-103.3. Removal/installation - turret master relay.
9-110.3
C 11, TM 9-2350-230-12
Figure 9-103.4. Removal/installation - electrical harnesses (1 of 2).
9-110.4
C 11, TM 9-2350-230-12
Figure 9-103.5. Removal/installation - electrical harnesses (2 of 2).
(9-110.6 blank)/9-110. 5
C3, TM9-2350-230-12
Figure 9-104. Driver’s switch panel - lead connection guide
9-111
C8, TM 9-2350-230-12
Figure 9-105. Schematic wiring diagram - driver’s switch panel
9-112
C8. TM 9-2350-230-12
Figure 9-106. Removal/installation - driver’s indicator panel
9-113
C8, TM 9-2350-230-12
Figure 9-107. Removal/installation - personnel heater control box assembly
9-114
C8, TM 9-2350-230-12
Figure 9-107.1 Disassembly / assembly - personnel heater control box assembly
(9-114.2 Blank) 9-114.1

C4, TM 9-2350-230-12
Figure 9-108. Removal/installation - bilge pump relays and mount
PRELIMINARY STEP
OPEN RIGHT HAND EXHAUST GRILLE.
REMOVAL
1. BACK OFF ADJUSTING NUT AND ADJUSTER (1) TO END OF

ROD
CAUTION: WHEN BELTS ARE TO BE REMOVED, SUPPORT

GENERATOR BEFORE REMOVING TENSIONER.
2. COTTER PIN, WASHER, AND STRAIGHT PIN
3. SCREW (2)
4. BELT TENSIONER
INSTALLATION
REVERSE REMOVAL PROCEDURE. TIGHTEN ADJUSTER (1)

UNTIL SPRING IS FULLY COMPRESSED.
NOTE. TENSIONER IS SELF ADJUSTING. REPLACE BELTS
IF PIN IS WITHIN 1/4 INCH FROM BOTTOMING OUT. WHEN
REPLACING BELTS, ALWAYS REPLACE THE COMPLETE SET OF
FOUR.
WE11036A|
Figure 9-109. Removal/installation - generator "V" belt tensioner
9-115
C11, TM 9-2350-230-12
Figure 9-110. Removal/installation/adjustment - voltage regulator (1 of 2).
9-116
C11, TM 9-2350-230-12
Figure 9-110. 1. Removal/installation/adjustment -voltage regulator (2 of 2).
(9-116.2 blank)/9-116. 1
C8, TM 9-2350-230-12
PRELIMINARY STEPS
A. SUITABLE HOIST AND SLINGS MUST BE AVAILABLE TO

LIFT GENERATOR FROM VEHICLE.
B. REMOVE HULL ACCESS PLUG UNDER RIGHT ENGINE
MOUNTING SCREW (ITEM 6, FIGURE 5-7). PLACE
BLOCKING APPROXIMATELY 8 INCHES HIGH ON HULL
FLOOR UNDER GENERATOR CRADLE. (IF POWER PLANT
IS OUT OF VEHICLE, USE SUITABLE BLOCKING UNDER
CRADLE TO PREVENT CRADLE FROM DROPPING BELOW
LEVEL POSITION).
REMOVAL
1. DISCONNECT GROUND STRAP AND ELECTRICAL LEADS,

CIRCUITS 14, 15, AND 152, AT GENERATOR TERMINAL
BOX.
2. LOOSEN BELT TENSIONER (FIGURE 9-109) AND REMOVE
BELTS.
3. REMOVE TWO SCREWS AND REMOVE BELT TENSIONER
FROM GENERATOR DRIVE HOUSING.
4. PLACE SLING AROUND FRONT END OF GENERATOR
NEXT TO GENERATOR DRIVE HOUSING. CONNECT
HOIST TO SLING AND REMOVE SLACK.
5. REMOVE CLIP AND WASHER FROM GENERATOR
SUPPORT ROD.
6. UNSCREW RETAINING CLAMP NUTS AND RELEASE
CLAMPS. RELEASE TENSION ON HOIST UNTIL
GENERATOR PULLEYS WILL CLEAR FAN STATOR, THEN
SLIDE GENERATOR FORWARD UNTIL HOUSING CLEARS
SUPPORT ROD.
7. RELEASE TENSION ON HOIST UNTIL GENERATOR RESTS
ON BLOCKING.
8. PLACE SECOND SLING AROUND REAR END OF
GENERATOR, AND HOIST GENERATOR OUT OF VEHICLE.
CAUTION: GENERATOR IS HEAVY- HANDLE CAREFULLY TO

AVOID INJURY TO PERSONNEL OR DAMAGE TO EQUIPMENT.
INSTALLATION
REVERSE REMOVAL PROCEDURE. BEFORE INSTALLING

BELTS, RAISE GENERATOR UNTIL OIL FILL PLUG IS LEVEL WITH
PULLEY SHAFT AND CHECK OIL LEVEL IN ACCORDANCE WITH
LO 9-2350-230-12. REFER TO FIGURE 9-109 FOR ADJUSTMENT
OF BELT TENSIONER.
GENERATOR POLARITY
AFTER INSTALLING GENERATOR AND BEFORE CONNECTING

GENERATOR-TO-VOLTAGE REGULATOR HARNESS, CONNECT
NEGATIVE TERMINAL OF BATTERY (12 OR 24V.) TO TERMINAL E
(GROUND) ON GENERATOR, AND POSITIVE BATTERY TERMINAL
MOMENTARILY TO TERMINAL A (SHUNT FIELD). THIS WILL
INSURE PROPER GENERATOR POLARITY.
BRACKET REMOVAL/INSTALLATION
REMOVE 5 SCREWS, WASHERS AND GENERATING MOUNTING

BRACKET. TIGHTEN SCREWS TO 16-20 POUND-FEET AT
INSTALLATION.
WE 665561
Figure 9-111. Removal/installation - generator and drive assembly
9-117
C9, TM 9-2350-230-12
Figure 9-112. Removal/installation - generator drive, pulley, cradle, bracket, and V-belt tensioner bracket
9-118
C11, TM 9-2350-230-12
Figure 9-112.1. Removal/installation/repair - generator-to-voltage regulator wiring harness.
9-118.1
C4, TM 9-2350-230-12
Figure 9-112.2. (Added) Repair - starter/starter relay wiring harness
9-118.2
C4, TM 9-2350-230-12
PRELIMINARY STEPS
1. REMOVE POWER PLANT (FIGURES 9-3 THROUGH 9-6).

2. REMOVE GENERATOR (FIGURE 9-111).
REMOVAL
1. REMOVE NUT AND FLAT WASHER AND DISCONNECT

GROUND STRAP AT STARTER.
2. REMOVE NUT AND FLAT WASHER AND DISCONNECT
STARTER CABLE.
3. REMOVE SCREW AND DISCONNECT SOLENOID LEAD.
4. REMOVE 5 SCREWS, LOCK WASHERS, AND FLAT
WASHERS AND REMOVE GENERATOR SUPPORT
CRADLE AND GENERATOR SUPPORT BRACKET AS A
COMBINED UNIT.
5. REMOVE BOLT, 2 SCREWS AND LOCK WASHERS AND
PULL STARTER STRAIGHT OUT FROM ENGINE HOUSING.
CAUTION: STARTER WEIGHS APPROXIMATELY 80

POUNDS, USE CARE DURING REMOVAL AND
INSTALLATION
INSTALLATION
REVERSE REMOVAL PROCEDURE TO INSTALL ENGINE

STARTER.
C. ENGINE STARTER - INSTALLED VIEW. WE 11112AI
Figure 9-113. (Superseded) Removal/installation - engine starter
9-119
TM 9-2350-230-12
REMOVAL- ENGINE COOLANT HIGH TEMPERATURE SWITCH

AND TEMPERATURE TRANSMITTER
PRELIMINARY STEPS
A. REMOVE AIR INLET GRILLE, GRILLE SUPPORT, AND

ENGINE ACCESS COVER (STEPS I THROUGH 5, FIG. 9-3).
B. REMOVE CAP FROM TOP OF COOLANT SURGE TANK
AND DRAIN COOLANT BELOW LEVEL OF SWITCH OR
TRANSMITTER. USE SUITABLE CONTAINER. PETCOCK
IS LOCATED ON BOTTOM OF THERMOSTAT HOUSING
(FIG. 9-2).
A. ENGINE COOLANT HIGH TEMPERATURE SWITCH AN,J

ENGINE COOLANT TRANSMITTER.
REMOVAL- TRANSMISSION TEMPERATURE AND PRESSURE

SWITCHES
PRELIMINARY STEPS
A. OPEN LEFT ENGINE GRILLE.

B. REMOVE AIR CLEANER DUCT AND COVER OPENINGS IN
AIR CLEANER AND TURBOCHARGER (STEP I,FIG.9-4).
REMOVAL
1. DISCONNECT ELECTRICAL LEAD TO UNSERVICEABLE

B. TRANSMISSION OIL HIGH TEMPERATURE SWITCH AND LOW ITEM.
PRESSURE SWITCH. REMOVAL - ENGINE OIL PRESSURE 2. UNSCREW UNSERVICEABLE SWITCH.
SWITCH
INSTALLATION
REVERSE REMOVAL PROCEDURE
PRELIMINARY STEPS
A. OPEN LEFT ENGINE GRILLE.

B. REMOVE AIR CLEANER DUCT AND COVER OPENINGS IN
AIR CLEANER AND TURBOCHARGER (STEP I, FIG. 9-4).
REMOVAL
1. DISCONNECT ELECTRICAL LEAD.

2. UNSCREW SWITCH.
INSTALLATION

C. ENGINE OIL LOW PRESSURE SWITCH . WE 11095
Figure 9-114. Removal/installation - power plant temperature and pressure switches and transmitters
9-120
C8, TM 9-2350-230-12
B. TACHOMETER GENERATOR INSTALLED ON ADAPTER.
REMOVAL- TACHOMETER GENERATOR
1. OPEN LEFT ENGINE GRILLE.

2. REMOVE AIR CLEANER DUCT, COVER OPENINGS IN AIR
CLEANER DUCT. CLEANER AND TURBOCHARGER (STEP
1, DIG. 9-4).
3. DISCONNECT ELECTRICAL LEAD.
4. ENGINES PRIOR TO SN 6D 42352: UNSCREW
GENERATOR. USE CARE DURING REMOVAL AND
INSTALLATION TO AVOID LOSING KEY (FIG. 9-116, ITEM
13).
4A. EFFECTIVE ENGINE SN 6D 42352: REMOVE 2 BOLTS AND
A. TACHOMETER GENERATOR RIGHT ANGLE DRIVE ADAPTER WASHERS (FIG. 9-116, ITEMS 17 AND 18) AND REMOVE
(ENGINES PRIOR TO SN 6D 42352) INSTALLATION SURGE TACHOMETER GENERATOR
TANK AND BRACKET REMOVED FOR CLARITY
INSTALLATION
REMOVAL - SPEEDOMETER GENERATOR AND ODOMETER

ADAPTER.
PRELIMINARY STEPS
A. OPEN BOTH ENGINE GRILLES.
B. REMOVE 2 REAR SCREWS ATTACHING GRILLE SUPPORT
TO ENGINE ACCESS COVER.
C .REMOVE ENGINE ACCESS COVER (STEPS 3, 4, AND 5,
FIG. 9-3).
REMOVAL
1. DISCONNECT ODOMETER AND SPEEDOMETER
ELECTRICAL LEADS.
2 . UNSCREW GENERATOR. USE CARE DURING
REMOVAL OR INSTALLATION TO PREVENT LOSS OF KEY (ITEM
C. SPEEDOMETER GENERATOR ASSEMBLY 13, FIG. 9-116).
ANDODOMETER ADAPTER 3 DISCONNECT SPEEDOMETER CABLE
4. REMOVE 2 NUTS, WASHERS, SCREWS, AND ODOMETER
ADAPTER.
INSTALLATION
INSTALLATION NOTE. TWO EXTERNAL-TOOTHED

LOCKWASHERS MUST BE INSTALLED BETWEEN ODOMETER
ADAPTER AND HULL BRACKET TO PROVIDE PROPER GROUND.
TIGHTEN SCREWS TO 25-31 POUND-FEET.
WE 12185 |
Figure 9-115. Removal/installation - speedometer and tachometer generators, and odometer adapter
9-121
C8, TM 9-2350-230-12
Figure 9-116. Removal/installation - odometer, speedometer and tachometer generator drives
9-122
TM 9-2350-230-12
Figure 9-117. Replacing cable terminals and connectors.
9-123
TM 9-2350-230-12
Figure 9-118. Replacing typical electrical plug and receptacle connectors
9-124
C11, TM 9-2350-230-12
Section 9-6. HULL AND COMPONENTS
9-14. General
This section contains organizational main- figure 9-148 for repair of flotation skin and
tenance instructions for the vehicle hull and paragraph 9-15 for repair of barrier.
components listed in table 9-13. Refer to
TABLE 9-13. HULL AND COMPONENTS
FIGURE REFERENCE
ASSEMBLY OR COMPONENT ADJUST REPLACE REPAIR
Surfboard and Controls (Veh. Ser. 1-69) 9-119 9-119. 1

Surfboard and Controls (Eff. Veh. Ser. 70) 9-119. 2 9-119. 3, 119. 4
Driver’s Rotatable Hatch. Components 9-120, 121
Driver’s Escape Hatch Components 9-122
Driver’s Seat 9-123 9-124, 125
Ammunition Racks 9-126, 127, 128
Bilge Pumps (Rear) 9-129 9-129
Bilge Pump (Front) 9-130,131.1 9-130, 131,131.2
Personnel Heater 9-132 9-133 through
9-137
Crew Compartment Fire Extinguisher 9-138, 138.1 9-139, 139.2 9-139, 139.3,
139.4
Fixed (Engine Compartment) Fire Extinguisher 9-138, 140 9-139, 141 9-139, 141
Radiator Contamination Shield and Grille.
Debris Screens 9-142.1
Hull Interior Stowage 9-145, 146, 146.1
Hull Exterior Stowage 9-147
Flotation Skin 9-148
Air Cleaner and Battery Access Cover 9-142. 2 9-142. 2
ADJUSTMENT
1. ADJUST TWO REAR BRACE BARS TO REMOVE WRINKLES FROM REAR BARRIER. DO NOT OVERTIGHTEN.
2. ADJUST FRONT AND REAR SUPPORT ARMS TO REMOVE WRINKLES FROM BARRIER SIDES. DO NOT OVERTIGHTEN AS
PRODUCTION TOLERANCES MAY RESULT IN SOME WRINKLES.
TA0073351
Figure 9-119. Adjustment - surfboard and barrier supports (effective through vehicle serial no. 69)
9-125
C4, TM 9-2350-230-12
Figure 9-119.1. Disassembly/repair/assembly - surfboard and barriers (effective through vehicle serial no. 69)
9-126
C4, TM 9-3580-230-12
TABLE 9-13.1. LEGEND FOR FIGURE 9-119.1
1. PAD - 10955301 24. BRACKET - 10955303

2. PLATE - 10955302 25. WASHER - MS27183-18
3. NUT - 8712289-2 26. COTTER PEN - MS24665-285
4. SHIM - 10955299-1, -2, -3 27. SPRING PIN - MB9048-015
5. SPACER - 10955298 28. SWIVEL JOINT - 10955292
6. LEVER - 10955297 29. PIN - 10955293
7. WASHER - 10941915-3 30. CLEVIS- 10955291-2
8. NUT - 8712289-3 31. SUPPORT - 10955290
9. SCREW - MS35191-322 32. PIN - N817990-C812
10. PLAT- 109,55275 33. CHAIN Type II CLASS 2 TRAD NO. 7,
11. SCREW - M119077-39 (6-INCHES LONQ)
12. WASHER - 10955576-1 34. LUG - 10955294
13. BRACKET - 10955300 35. BRACKET -10955304
14. SCREW - MS90728-80 36. SCREW - M90727-66
15. BRACKET - 10955520 37. 8CREW - 1190727-65
16. WASHER - 10910174-3 38. 8-HOOK - 1887006-23
17. WASHER - 10910174-2 39. CLEVIS - 10955291-1
18. GUARD - 10956065 40. LEFT BRACKET - 10955532-1
19. CLIP - 10955295 RIGHT BRACKET - 10955522-2 (NOT SHOWN)
20. HOLD-DOWN - 10953785 41. WASHER - 10955576-2
21. RETAINER - 10953780 42. SCREW - M635191-325
22. SCREW - MS90728-62 43. SCREW - 1190727-38
23. PIN - MS20392-7C53 44. BRACKET - 10955518
9-126.1
C11 , TM 9-2350-230-12
PRELIMINARY STEPS (REFER TO FIG. 9-119.3 AND 9-119.4) ADJUSTMENT (REFER TO FIG. 9-119.3)
1. LOOSEN LOCKNUT (ITEM 34) AND ADJUST SETSCREW SO
A. RELEASE LATCHES TO PERMIT SURFBOARD EXTENSION THAT EYEBOLT ASSEMBLY (ITEMS 27 THROUGH 32) IS 90’
TO FOLD DOWN BEFORE REMOVING LATCH TO HULL SURFACE. THEN BACK SETSCREW OUT TWO
COMPONENTS. MORE TURNS, AND TIGHTEN LOCKNUT.
2. LOOSEN LOCKNUTS (ITEMS 28 AND 29) AND ADJUST
B. BLOCK SURFBOARD SECURELY IN UPRIGHT POSITION LENGTH OF EYEBOLT ASSEMBLY BY TURNING BARREL
BEFORE REMOVING SUPPORT BRACKETS OR UNTIL UNDER SURFACE OF UPPER SUPPORT (ITEM 22)
ASSOCIATED HARDWARE. JUST TOUCHES MACHINED SURFACE OF LOWER SUPPORT
(ITEM 44). TIGHTEN LOCKNUTS.
C. ITEMS 99 THROUGH 116. REMOVE SCREWS AND 3. SURFBOARD RELEASE BRACKET MAY BE ADJUSTED BY
RETAINING STRIPS AS NECESSARY TO FOLD BACK FRONT LOOSENING MOUNTING SCREWS (ITEM 54) AND
SECTION OF FLOTATION BARRIER TO GAIN ACCESS TO REPOSITIONING BRACKET TO RETAIN RELEASE HANDLE
ITEMS 99 THROUGH 116. (SEE PHOTO ABOVE. (ITEM 38) IN LOCKED POSITION.
4. ADJUST SLACK IN WIRE ROPE (ITEM 6) BY MEANS OF
INSTALLATION NOTE CLEAN MOUNTING SURFACE ON LOCKNUTS (ITEM 5) AT THE LATCH, SO THAT UPPER
SURFBOARD, AND APPLY SEALING TAPE FSN 8030-262- SURFBOARD RELEASES SIMULTANEOUSLY WITH INITIAL
9019 ALONG BEAD OF FLOTATION BARRIER BETWEEN RELEASE OF MAIN SURFBOARD. UPPER SURFBOARD
BARRIER AND SURFBOARD. MUST BE RELEASED BEFORE MAIN SURFBOARD
STARTSTO FALL.
DISASSEMBLY/REPAIR/ASSEMBLY TA0073361
REPLACE UNSERVICEABLE COMPONENTS AS REQUIRED.
Figure 9-119.2 Disassembly/repair/assembly - surfboard and barriers

(effective vehicle serial no. 70) (1 of 3).
9-126.2
C4, TM 9-2350-230-12
Figure 9-119.3 (Superseded) Disassembly/repair/assembly - surfboard and barriers (2 of 3) (effective with vehicle serial
no. 70)
9-126.3
C4, TM 9-2350-230-12
Figure 9-119.4 (Superseded) Disassembly/repair/assembly - surfboard and barriers

(3 of 3) (effective vehicle serial no. 70)
9-126.4
C10, TXM 9-2350-230-12
Figure 9-120. Removal/installation - driver’s rotatable hatch locking latch, grip, and o
bumpers
9-126.5
C10, TM 9-2350-230-12
Figure 9-120.1. Removal/installation/adjustment - driver’s rotatable hatch emergency

outside latch release and open position latch stop
9-126.6
C9, TM 9-2350-230-12
1. REMOVE CLIP, RETAINER PLATE AND BUMPER 1. WHEN REPLACING SEALS, ALSO REPLACE
(W/SLEEVE) FROM ENDS OF HULL SEAL PLATE BUMPERS.
(VIEW A).
2. USE ADHESIVE MIL-A-5092 TYPE II TO
2. REMOVE SEVEN SCREWS AND REMOVE HATCH INSTALL NEW SEALS AND NEW BUMPERS.
SEAL PLATE FROM ROTATABLE HATCH. FOLLOW INSTRUCTIONS IN PARAGRAPH
(VIEW D). 8-6 FOR APPLICATION OF ADHESIVE.
3. REMOVE SCREW, RETAINER PLATE, BUMPER 3. REINSTALL CLIPS AND RETAINER PLATES IN
(W/SLEEVE) AND SEAL CLIP FROM HATCH ORIGINAL LOCATIONS.
SEAL PLATE (VIEW C).
4. ON HATCH SEAL PLATE, LET UPPER LIP OF
4. USE SUITABLE TOOL TO STRIP OFF OLD SEAL EXTEND BEYOND SEAL PLATE AS
SEALS (VIEWS A, B, D). CLEAN SEAL GROOVES SHOWN IN VIEW C. CEMENT LIP TO TOP
TO BARE METAL. OF BUMPER AT ASSEMBLY, AND TRIM FLUSH
WITH BUMPER.
WE 66594
Figure 9-121. Removal/installation - driver’s rotatable hatch seals
9-127
C4, TM 9-2350-230-12
Figure 9-122. Removal/Installation - driver’s aluminum escape hatch

cover (early vehicles)
9-128
C9, TM 9-2350-230-12
Figure 9-122.1. Removal/Installation - driver’s steel escape hatch cover

(later vehicles)
9-128.1
C11, TM 9-2350-230-12
Figure 9-123. Removal/installation - driver’s seat and components.
9-128.2
C4, TM 9-2350-230-12
Figure 9-124. Disassembly/assembly - driver’s seat and components (1 of 2)
9-129
C10, TM 9-2350-230-12
Figure 9-125. Disassembly/assembly - driver’s seat and components (2 of 2)
9-130
TM 9-2350-230-12
Figure 9-126. Disassembly/assembly - hull ammunition racks (right side)
9-131
C4, TM 9-2350-230-12
Figure 9-126.1. (Added) Hull right ammunition rack conversion - conventional

round to missile and missile to conventional round stowage (effective vehicle S/N 700)
9-132
C4, TM 9-2350-230-12
This page left blank intentionally.
9-132.1
TM 9-2350-230-12
Figure 9-127. Disassembly/assembly - hull ammunition racks (left side, front)
9-132.2
TM 9-2350-230-12
Figure 9-128. Disassembly/assembly - hull ammunition racks (left side, rear)
9-133
C4, TM 9-2350-230-12
Figure 9-129. (Superseded) Disassembly/assembly - rear bilge pumps and components
9-134
C4, TM 9-2350-230-12
Figure 9-130. (Superseded) Disassembly/assembly - front bilge pump and components

(1 of 2) (effective through vehicle serial no. 139)
9-135
C4, TM 9-2350-230-12
NOTES 1. WHEN INSTALLING NEW PUMP (ITEM 36) DISCARD 1/4 INCH THICK SHIPPING BLOCK THAT IS
SUPPLIED WITH PUMP AND USE EXISTING SCREWS AND WASHERS. PLUG VENT HOLE
WITH NEW DRIVE SCREW (ITEM 37).
2. ASSEMBLE CHAMBER TO PLATE APPLYING SEALER GRADE CV (8030-081-2330).
3. AFTER ASSEMBLING VALVE (ITEM 29), WIPER PLATE (ITEM 28), AND RETAINER (ITEM 27), TO
ARM SHAFT (ITEM 31) WITH SCREWS (ITEM 26), STAKE HEADS OF SCREWS TO RETAINER.
4. TO PROVIDE PROPER PRELOAD ON TORSION SPRING (ITEM 25), ASSEMBLE TORSION

SPRING AND ADJUSTER (ITEM 24) ON ARM SHAFT (ITEM 31) ROTATE ADJUSTER ONE SLOT
IN A COUNTERCLOCKWISE DIRECTION AND ASSEMBLE SPRING PIN (ITEM 23).
5. WHEN ASSEMBLING HANDLE OF VALVE CONTROL ARM (ITEM 31) TO RETAINING SPRING
(ITEM 18), GREASE SPRING WITH GAA GREASE AND ADJUST HEIGHT OF SPRING USING
SPACERS (ITEM 19) TO PROVIDE CORRECT TRAVEL. (SEE BELOW).
Figure 9-131. (Superseded) Disassembly/assembly - front bilge pump and components

(2 of 2) (effective through vehicle serial no. 139)
9.136
C4, TM 9-2350-230-12
Figure 9-131.1 Removal installation - front bilge pump and components

(effective vehicle serial no. 140)
9.136.1
C4, TM 9-2350-230-12
Figure 9-131.2. (Added) Disassembly/assembly - front bilge pump and components

(effective vehicle serial no. 140)
9.136.2
C4, TM 9-2350-230-12
A. PLACE PERSONNEL HEATER FUEL SHUT-OFF B. DISCONNECT WIRING HARNESS PLUG AT

VALVE IN "OFF" POSITION, AS SHOWN. HEATER RECEPTACLE.
C. 1. LOOSEN CLAMP AND REMOVE

HEATER HOSE FROM HEATER DUCT
ASSEMBLY.
2. DISCONNECT FUEL HOSE AT HEATER
ELBOW.
3. LOOSEN CLAMP AND REMOVE
HEATER EXHAUST TUBE FROM
HEATER.
4. DISCONNECT 2 CLAMPS AND REMOVE
HEATER ASSEMBLY WITH DUCT
ASSEMBLY.
5. REMOVE 4 SCREWS AND DUCT
ASSEMBLY FROM HEATER ASSEMBLY.
WE11257
Figure 9-132. (Superseded) Removal/installation - personnel heater
9-137
C4, TM 9-2350-230-12
LEGEND
1.PUMP ASSEMBLY 10. SCREW (2)
2. ELBOW 11. FILTER ASSEMBLY
3. HOSE 12. ELBOW (2)
4. NUT (2) 13. HOSE ASSEMBLY
5. WASHER (4) 14. WASHER (2)
6. GROUND LEAD 15. SCREW (2)
7. SCREW (8) 16. ADAPTER
8. WASHER (2) 17. HOSE ASSEMBLY
9. CUSHION
REMOVAL/INSTALLATION
REPLACE UNSERVICABLE COMPONENTS AS REQUIRED.

REFER TO FIGURE 9-134 FOR FILTER AND PUMP
SERVICE.
Figure 9-133. (Superseded) Removal/installation - personnel heater fuel pump, filter, valve,
lines, and fittings
9-138
C3, TM 9-2350-230-12
FUEL FILTER ASSEMBLY FOR: ELECTRIC FUEL PUMP

PERSONNEL HEATER/COOLANT HEATER ........ .2915-025-3493 PERSONNEL HEATER/COOLANT HEATER (INTERCHANGEABLE)
FUEL TANK DRAIN PUMP ..................................... 2940-930-3248
ELEMENT ASSEMBLIES ARE NOT INTERCHANGEABLE.
LEGEND
LEGEND 1. CAP 3. FILTER
1. BOWL 4. PACKING 2. GASKET 4. HOUSING
2. WASHER 5. HEAD DISASSEMBLY
3. ELEMENT ASSY. (DO NOT REMOVE SPRING) UNLOCK CAP FROM HOUSING AND DISASSEMBLE PUMP
DISASSEMBLY BY FOLLOWING NUMERICAL SEQUENCE. CLEAN FILTER
UNSCREW BOWL FROM HEAD AND DISASSEMBLE AS IN DRY CLEANING SOLVENT OR MINERAL SPIRITS PAINT
REQUIRED. CLEAN FILTER ELEMENT IN DRY CLEANER THINNER, AND DRY WITH LOW PRESSURE AIR.
SOLVENT OR MINERAL SPIRITS PAINT THINNER, AND Y
DRY WITH LOW PRESSURE AIR. ASSEMBLY
REVERSE DISASSEMBLY PROCEDURE.
ASSEMBLY
REVERSE DISASSEMBLY PROCEDURE. WE 11276A |
Figure 9-134. (Superseded) Disassembly/assembly -

Fuel filter-personnel heater, coolant heater, and fuel drain pump,
Electric fuel pump - personnel heater and coolant heater.
LEGEND
1. SCREW (16)
2. SHOCK MOUNT (4)
3. SCREW (4)
4. BRACKET (2)
5. CLAMP (2)
REMOVAL
REMOVE PERSONNEL HEATER SHOCK
MOUNTS BY FOLLOWING NUMERICAL
SEQUENCE.
INSTALLATION
WE 11088
Figure 9-135. Removal/installation - personnel heater shock mounts
9-139
C4, TM 9-2350-230-12
PERSONNEL HEATER WIRING DIAGRAM (LOCATED INSIDE GUARD) WE 11259 |
Figure 9-136. (Added) Removal/installation - personnel heater guard
9-140
C4, TM 9-2350-230-12
PERSONNEL HEATER IGNITER, OVERHEAT SWITCH, AND

FLAME DETECTOR SWITCH.
(AIR VALVE REMOVED FOR CLARITY) ,3
FLAME DETECTOR
SWITCH ASSEMBLY
PRELIMINARY STEP FLAME DETECTOR SWITCH ADJUSTMENT
REMOVE GUARD ASSEMBLY FROM HEATER (FIGURE 9- 1. CHECK BOW SPRING TO SEE IF TENSION OF
136). QUARTZ ROD IS CAUSING IT TO BOW UP
TOWARD THE TOP OF THE SWITCH. IF SPRING
REMOVAL- IGNITER IS NOT BOWED BUT IS IN A STRAIGHT POSITION,
1. REMOVE NUT AND TWO WIRES FROM TOP OF IT MAY BE ASSUMED THAT QUARTZ ROD IS
IGNITER BROKEN. REPLACE SWITCH.
2. USE 13/16 THIN WALL DEEP SOCKET TO SEN 2. IF SPRING IS BOWED, LOOSEN TWO SWITCH
IGNITER, HOLD GROUND STRAP DOWN AND MOUNTING SCREWS UNTIL MICRO SWITCH CAN
UNSCREV IGNITER BY HAND. PIVOT.
NOTE. IF THIN WALL SOCKET IS NOT AVAILABLE, 3. BACK OFF ADJUSTING SCREW UNTIL SWITCH
DISCONNECT FUEL LINE AND REMOVE 450 "CLICKS."
ELBOW AT THE FUEL CONTROL VALVE TO 4. TURN ADJUSTING SCREW IN UNTIL SWITCH
PROVIDE CLEARANCE FOR A STANDARD "CLICKS" AGAIN AND CONTINUE FOR
SOCKET. ADDITIONAL 1/4 TURN FROM CLICK POINT.
3. REMOVE IGNITER FROM HEATER. SWITCH IS NOW CORRECTLY ADJUSTED.
5. TIGHTEN TWO SWITCH MOUNTING SCREWS TO
REMOVAL - OVERHEAT SWITCH HOLD SWITCH IN PROPER POSITION.
1. DISCONNECT 3 WIRES FROM OVERHEAT NOTE. WHEN INSTALLED, THIS SWITCH MUST
SWITCH TERMINALS. OPERATE WITHIN 40 SECONDS AFTER
2. REMOVE TWO SCREWS AND OVERHEAT HEATER IGNITES. AFTER HEATER GOES
SWITCH. REMOVAL - FLAME DETECTOR SWITCH OUT OR IS SHUT OFF, SWITCH MUST
ASSEMBLY 1. DISCONNECT FIVE WIRES FROM NOT RE-OPERATE WITHIN 1 MINUTE BUT
FLAME DETECTOR MICROSWITCH TERMINALS. MUST RE-OPERATE WITHIN 3-1/2
REINSTALL TERMINAL SCREWS AND MINUTES.
LOCKWASHERS TO PREVENT LOSS.
2. USE 1/2-INCH OPEN END WRENCH TO LOOSEN INSTALLATION
COMPRESSION NUT. REVERSE REMOVAL PROCEDURE, REPLACING
3. LIFT FLAME DETECTOR ASSEMBLY STRAIGHT UNSERVICEABLE COMPONENTS AS REQUIRED.
OUT OF HOUSING TO AVOID BREAKING CONNECT WIRING AS SHOWN ON WIRING DIAGRAM,
CERAMIC ROD. FIGURE 9-136. WHEN REPLACING FLAME DETECTOR
SWITCH ASSEMBLY, RETURN OLD SWITCH ASSEMBLY
TO SUPPORT MAINTENANCE FOR REPAIR AND RETURN
TO STOCK.
Figure 9-137. Removal/installation - personnel heater igniter, overheat switch,

and flame detector switch assembly
9-141
C10, TM 9-2350-230-12
Figure 9-138. Adjustment - crew compartment and fixed (engine compartment)

fire extinguisher control linkage (1 of 2)
9-142
C10, TM 9-2350-230-12
Figure 9-138.1. Adjustment - crew compartment and fixed (engine compartment)

fire extinguisher control linkage (2 of 2)
(9-142. 2 Blank) 9-142.1

C10, TM 9-2350-230-12
Figure 9-139. Disassembly/assembly - crew compartment and fixed (engine compartment)

fire extinguisher control systems (1 of 2)
9-143
C10, TM 9-2350-230-12
Figure 9-139.1. Disassembly/assembly - crew compartment and fixed

(engine compartment) fire extinguisher control systems (2 of 2)
9-144
C10, TM 9-2350-230-12
Figure 9-139.2. Removal/installation - crew compartment fire extinguisher

cylinder
9-144.1
C10, TM 9-2350-230-12
Figure 9-139.3. Crew compartment fire extinguisher wiring harness

location reference, wiring diagram, and repair of switch assembly
9-144.2
C10, TM 9-2350-230-12
FOR LOCATION AND IDENTIFICATION OF TURRET

HARNESSES AND LEAD, SEE FIGURE 9-139.3.
Figure 9-139.4. Repair - crew compartment fire extinguisher hull wiring harnesses
9-144.3
C10, TM 9-2350-230-12
Figure 9-140. Fixed fire extinguisher cylinder replacement
9-144.4
C10, TM 9-2350-230-12
Figure 9-141. Removal/installation/repair - fixed fire extinguisher control system (1 of 2)
9-145
C10, TM 9-2350-230-12
Figure 9-142. Removal/installation/repair - fixed fire extinguisher control system (2 of 2)
9-146
C11, TM 9-2350-230-12
Figure 9-142.1. Removal/Installation - radiator contamination shield and grille debris screens
9-146.1
C8, TM 9-2350-230-12
LEGEND LEGEND
VEHICLES SN 1 THROUGH 1292 EFFECTIVE VEHICLE SN 1293 0
1. S-HOOK (4) 1. PIN (2)
2. CHAIN (2) 2. PIN k2)
3. PIN ASSEMBLY (2) 3. CLIP (2)
REPLACE UNSERVICEABLE COMPONENTS AS REQUIRED,
WE 12197
Figure 9-142.2. Repair - battery and air cleaner access doors
9-146.2
TM 9-2350-230-12
LEGEND
1. SCREW (3)
2. DOOR ASSEMBLY (SHOWN WITH TAILLIGHT)
3. INDICATOR LIGHT JEWEL HOLDER ASSEMBLY
4. INDICATOR LIGHT LAMP
PRELIMINARY STEP
TURN MASTER SWITCH TO "OFF" POSITION. OPEN INTERCOM DOOR, DISCONNECT ELECTRICAL LEADS (INDICATOR
LIGHT TO INTERCOM BOX AND TAILLIGHT TO WIRING HARNESS).
REMOVAL
REMOVE BY FOLLOWING NUMERICAL SEQUENCE.
NOTE: DOOR ASSEMBLY MAY BE REMOVED FROM VEHICLE WITHOUT REMOVING INDICATOR LAMP OR TAILLIGHT.
INSTALLATION
REVERSE REMOVAL PROCEDURE
NOTE: 1. WHEN ATTACHING HINGE BRACKET, CLEAN HULL MOUNTING FACES AND APPLY SEALER PER MIL S-22473
GRADE B.
2. TO ADJUST SPRING COMPRESSION ON HINGE, TIGHTEN HINGE NUT INCREASING SPRING COMPRESSION
UNTIL DOOR IS MAINTAINED IN OPEN POSITION.
WE 1043
Figure 9-143. Disassembly/assembly -,ground intercom box door assembly and components
(1 of 2)
9-147
TM 9-2350-230-12
Figure 9-144. Disassembly/assembly - ground intercom box door assembly and components
(2 of 2)
9-148
C 10, TM 9-2350-230-12
Figure 9-144. 1-deleted.
Figure 9-145. Hull interior stowage (1 of 3)
9-148.2/(9-148.1 Blank)
C 10, TM 9-2350-230-12
Figure 9-146. Hull interior stowage (2 of 3)
9-149
C 10, TM 9-2350-230-12
PRELIMINARY STEP REMOVAL

LATCH DRIVER’S HATCH IN OPEN POSITION AND 1. SCREWS (2), WASHERS (4), AND NUTS (2).
REMOVE ALL GRENADE LAUNCHERS FROM RACK. 2. FOUR SCREWS AND WASHERS.
3. GRENADE LAUNCHER RACK ASSEMBLY.
NOTE. VIEW A IS APPLICABLE ONLY TO
VEHICLES LESS MISSILE CAPABILITY. INSTALLATION
REVERSE REMOVAL PROCEDURE. REPLACE
STRAPS IF WORN OR DAMAGED.
WE 66708
POSITION TURRET WITH GUN-LAUNCHER OVER REAR OF VEHICLE. REMOVE CLIPS AND LOADER’S
PROTECTIVE SCREEN TO GAIN ACCESS TO 7.62MM MACHINE GUN SPARE BARREL. REPLACE WORN OR
DAMAGED STRAPS. WE 66708
Figure 9-146.1. Hull interior stowage (3 of 3)
9-150
C10, TM 9-2350-230-12
Figure 9-147. Hull exterior stowage
9-151
C1, TM 9-2350-230-12
Figure 9-148. Repair of flotation skin.
9-152
C1, TM 9-2350-230-12
9.15. Barrier Repair buffed area, using the top of the can, clean fingers, or a
brush. Allow the spread fluid to dry from 3 to 5 minutes,
a. General. depending on ambient temperatures. In extremely hot,
dry X areas, the drying time may be reduced to as little
This procedure utilizes the cold patch technique as 1 minute. In cold areas, the drying time may exceed 5
(repair kit 5702943), and is intended for emergency field minutes. The treated surface should be dry to touch
repairs at ambient temperatures above 250F. A before the patch is applied.
vulcanizing fluid is used which achieves adhesion
through chemical reaction with the red uncured rubber NOTE. If the fluid turns milky white after application,
surface of the patch. The fluid is not a rubber cement, the surface is not perfectly dry or clean and
therefore, must be used in conjunction with the patches. Steps I and 2 above must be repeated.
Round patches are designed to accommodate holes up
to 2" in diameter. Oblong patches are designed to (4) Remove approximately 1/2 of the foil
accommodate tears less than 7" long. For tears longer backing from the patch to be used, taking
than 7", oblong patches may be overlapped to achieve care not to touch the uncovered portion of
the necessary length of repair. Overlap should be at least the patch. Apply the uncovered (red
1-1/2" at the tear point. uncured rubber) side of the patch to the
prepared surface. Remove the remaining
b. Repair Procedure. backing material and press patch into
place. Roll out any bubbles or wrinkles
(1) Using a wire brush or other suitable from the patch by working from the center
roughener, buff an area around the tear or of the patch to the edges (edge of fluid
hole approximately 1" larger than the can be used for this purpose). Make sure
patch to be used. that the edge of the patch is adequately
rolled.
(2) Remove dust from buffed area. Make
certain that the surface is perfectly dry. (5) Patch should be allowed to dry
Failure to follow these instructions will approximately 15 minutes to attain
result in an ineffective patch. maximum adhesive strength, however,
immediate use is permitted under
CAUTION: Do not use benzene or any other solvent. emergency conditions.
(3) Pour a sufficient amount of vulcanizing

fluid from the can to form a thin layer, and
spread over the
9-153
TM 9-2350-230-12
THIS PAGE LEFT BLANK INTENTIONALLY
9-154
C14, TM 9-2350-230-12
CHAPTER 10
ORGANIZATIONAL MAINTENANCE-TURRET
AND CUPOLA
WARNING: Before leaving vehicle, make certain that master switch and laser ON/OFF switch are in the
OFF position. This is to prevent accidental automatic alignment of cupola to main weapon (M551A1 only).
Section 10-1. TURRET ELECTRICAL SYSTEMS
10-1. General c. Refer to figure 10-2 for functional block diagram

a. This section contains organizational of turret electrical systems.
maintenance instructions for the turret electrical systems
which are classified into four categories according to d. The missile subsystem checkout procedure is
their respective functions. contained in table 2-12.
b. Figure 10-1 and table 10-1 identify and classify e. Vehicles serial numbers 140 through 223 are not
turret electrical components by primary systems. equipped with the missile subsystem. Refer to figure 10-
Maintenance instructions for each unit will be found in 2. 1 for functional block diagram of electrical components
the section covering that specific system. Components on these vehicles.
housing multiple-system application are classified
according to their primary function. CAUTION: Turn master switch off before
disconnecting or connecting electrical connectors to
avoid possible arcing.
Section 10-2. ELECTRICAL DRIVE CONTROL SYSTEM
10-2. General c. Refer to figure 10-1 and table 10-1 for

identification and locational reference of components of
a. This section contains organizational the system.
maintenance instructions for components of the electrical
drive control system listed in table 10-2. d. The electrical drive control system must be
tested and balanced whenever a component of the
b. The elevation limit switch assembly is a system has been replaced. Perform complete system
component of the drive control system; however, it is test procedures as outlined in figure 10-3 and table 10-3.
serviced by support maintenance personnel.
10-1
C4, TMV 9-2350-230-12
Figure 10-1. Turret electrical systems - locational reference
10-2
C8, TM 9-2350-230-12
TABLE 10-1. TURRET ELECTRICAL COMPONENTS - LOCATIONAL REFERENCE - (FIG. 10-1)
ITEM ITEM
NO. COMPONENT NO. COMPONENT
1 Elevating Mechanism Servo Motor 26 Amplifier Integrator Assembly
2 Missile Tracker Assembly 27 Receiver/Transmitter
3 Telescope Reticle Dimmer Box 28 Electric Drive Power Supply Assembly
4 Gunner’s Control Handle Assembly 29 Blasting Machine Impulse Generator
5** Telescope Emergency Power Supply 30 Modulator
6 Gun and Turret Control Selector 31 Antenna Match ing Unit
7 Dome Light No. 1 31. 1 Breech Scavenge Compressor
8 Grenade Projector Power Supply 32 Air Filter Unit
9 Circuit Cutout Box 33 Electric Contact Ring
10 Azimuth Indicator B 34 Signal Data Converter
11 Checkout Panel 35 Loader’s Intercom Control Box
36 Gyro Selector Assembly
12 Grenade Projector Control Box 37 Dome Light No. 2
13 Traverse Mechanism Servo Motor 38 Loader’s Control Box
14 Gunner’s Intercom Control Box 39 Relay Box
15 Commander’s Intercom Control Box 40 Forward Antenna
16 Commander’s Control Handle Assembly 41 M81 Gun-Launcher
17 Cupola Control Box 42 # 120-Volt Power Supply
18 Radio Amplifier 43 * Searchlight Main Control Box
19 Cupola Control Assembly 44 * Searchlight
20* Searchlight Remote Control Box 45 Elevation Limit Switches
21 Missile Subsystem Power Supply 46 # Ventilating Blower (Fume Control)
22 Cupola Traversing Mechanism 47 Rate Sensor
23 Motor-Generator 48 Gun Safety Switch
24 Dome Light No. 3 49 Optical Transmitter
25 Accessory Box Assembly
** Effective On Vehicle No. 140.

# Effective On Vehicle No. 60 - Earlier Vehicles by Retrofit.
* Special Purpose Kit (Refer to Chapter 12).
TABLE 10-2. Turret Electrical Drive Control System
FIGURE REFERENCE
ASSEMBLY OR COMPONENT REMOVE/
TEST ADJUST INSTALL
Accessory Box 10-3 10-4 10-4
Amplifier Integrator 10-3 10-5 10-5
Motor-Generator 10-3 10-6
Gunner’s and Commander’s Control Handles 10-3 10-7
Power Supply 10-3 10-8
Gyro Selector 10-3 10-9
Elevating and Traverse Mechanism Clutch Brushes 10-10
Elevating and Traverse Mechanism Servo Motors 10-11
Elevation and Depression Bump Stops 10-12
Gun-Launcher Depression Control 10-13
Test Set, Electric Drive Control 10-3
10-3
C9, TM 9-2350-230-12
Figure 10-2. Turret electrical systems - functional block diagram (1 of 5)
10-4
C9, TM 9-2350-230-12
Figure 10-2.1. Turret electrical systems - functional block diagram (2 of 5)
10-4.1
C9, TM 9-2350-230-12
10-4.2
C9, TM 9-2350-230-12
10-4.3
C9, TM 9-2350-230-12
10-4.4
C 14, TM 9-2350-230-12
Table 10-3. Electric Drive Control System Test Procedure
GENERAL INSTRUCTIONS
1. The electric drive control system test procedure provides isolation of trouble areas in the system. The test set,
when connected to the system at the amplifier integrator and ON, will allow operation of the system with the
traverse and elevation clutches and the motor-generator deenergized.
2. Perform test procedure in sequence for proper analysis. Observe indications at each test point and then proceed
to NO-GO remedy, if required. If a malfunction is corrected by replacement, repeat test procedure. Attach tag
with malfunction data (if known) to all components removed from turret.
NOTE
Test set needle is self-locking. When either lamp is illuminated, the needle has pegged and looked.
Needle may be released, providing current through meter is less than required to keep needle
pegged, by pressing (press-to-test) illuminated lamp or rotating test set selector to the next
position.
3. Perform test procedure and balance electric drive control system whenever a control box or assembly is replaced
in the system.
4. Notify support maintenance if any NO-GO condition cannot be corrected.
5. Refer to meter adjustment procedure for adjustment of locking arms
6. Check for proper voltage (27.5 to 29 volts) at dome light. Notify automotive mechanic if adjustment is required.
10-5
C 14, TM 9-2350-230-12

--Continued
10-6
C 14, TM 9-2350-230-12
--Continued
10-7
C 14., TX 9-2350-230-12
--Continued
10-8
C 14, TM 9-2350-230-12
--Continued
10-8.1
C 14, TM 9-2350-230-12
--Continued
10-8.2
C 14, TM 9-2350-230-12
--Continued
10-8.3
C 14, TM 9-2350-230-12
--Continued
10-8.4
C 14, TM 9-2350-230-12
--Continued
10-8.5
C 14, TM 9-2350-230-12
--Continued
10-8.6
C 14, TM 9-2350-230-12
--Continued
10-8.7
C 14, TM 9-2350-230-12
--Continued
10-8.8
C 14, TM 9-2350-230-12
--Continued
10-8.9
C 14, TM 9-2350-230-12
--Continued
10-8.10
C 14, TM 9-2350-230-12
--Continued
FINAL GAIN AND BALANCING PROCEDURES

NOTE
Final balancing of the system for both stabilized and nonstablized modes should be performed with
engine running. Vibration caused by engine or ’voltage ripple caused by the generating system will in
no way affect turret test set. However, following use of test set and/or when general troubleshooting
an electrical circuit, running of the engine is not recommended.
1. Operate the electric drive control system.
NOTE
The electric drive system may be operated with the test set connected providing:
a. Test set selector is on "0".
b. Test set switch is in "OFF" position.
2. The system gain is properly adjusted when weapon or turret does not oscillate when palm switch is depressed.
a. If oscillation occurs in non-stabilized mode, Turn ELEV and TRAV gain pots in amplifier integrator clockwise
until oscillation stops.
10-8.11
C 14, TM 9-2350-230-12
--Continued
FINAL GAIN AND BALANCING PROCEDURES

NOTE
Do not turn gain pots to within 60’ or less of the clockwise stop.
b. If oscillation occurs in stabilized mode, adjust summing gain pots (4A15 circuit board) (ELEV) and 4A16
circuit board (TRAV) clockwise until oscillation stops.
3. The system balance is properly adjusted when weapon or turret does not drift with palm switch depressed, or
during the 2 or 3 seconds drop-out delay after palm switch is released.
a. Drift with palm switch depressed (Non-stabilized Mode). With palm switch depressed eliminate drift with
control handle trim buttons. Check both control handles.
b. Drift During 2 to 3 Seconds Drop-Out Delay. With palm switch released, eliminate drift on circuit boards
2A1 traverse and 2A3 elevation (amplifier balance pots); then again check for drift during drop-out delay. Repeat till drift is
eliminated. If drift is too severe, it may be necessary to adjust the motor-generator balance pots R-10 (TRAV or ELEV) to
eliminate drift. If an adjustment is made to eliminate drift during the drop-out delay, repeat check for drift in nonstabilized
mode.
NOTE
Do not readjust trim buttons to eliminate drift in stabilized mode.
c. Drift with Palm Switch Depressed (Stabilized Mode). With palm switch depressed eliminate drift with gyro
balance pots 4A12 (TRAV) and 4A13 (ELEV) circuit boards.
10-8.12
C 14, TM 9-2350-230-12

--Continued
METER ADJUSTMENT PROCEDURE
Electronic Test Set (4933-00-909-9356)
Turn on turret power switch; ready light illuminates after 18 to 22 seconds. With multimeter, check +15 volts at pin "D"
and -15 volts at pin WE" of amplifier integrator test set receptacle (J2).
1. If voltage at pin "D" is from +14 to +16 volts and voltage at pin "E" is from -14 to -16 volts, turn off turret power,
reconnect test set harness to receptacle and turn on turret power. Wait until ready light illuminates.
2. Place test set selector to TP-6 and move red arm on right of test set meter to the left until Right/Up lamp
illuminates.
3. Place test set selector to TP-7 and move red arm on left of test set meter to the right until Left/Down lamp
illuminates.
10-8.13
C 14, TM 9-2350-230-12
Figure 10-3. Electric drive control test set.
Figure 10-4. Removal/installation/adjust

- accessory box.
10-8.14
C6, TM 9-2350-230-12
LEGEND
1. RELAY ASSY (A-1, A-2, A-3, A-4, A-5)

2. RELAY ASSY (A-6, A-7, A-8, A-9)
3. PRINTED CIRCUIT CONTROL BOARD (A-10)
4. TIMER ASSY (A-11)
5. TRAVERSE AMPLIFIER ASSY (A-12)
6. ELEVATION AMPLIFIER ASSY (A-13)
7. SHAPING AND FILTER ASSY (A-14)
8. ELEVATION SUMMING ASSY (A-15)
9. TRAVERSE SUMMING ASSY (A-16)
REPAIR
REPLACE UNSERVICEABLE COMPONENTS

AS REQUIRED.
WE 12118
Figure 10-4.1. Repair of accessory box assembly
10-9
C4, TM 9-2350-230-12
REMOVAL/INSTALLATION - INTEGRATOR AND/OR AMPLIFIER
1. TURN OFF GUN AND TURRET CONTROL "POWER" SWITCH.

2. UNLATCH AND OPEN HINGED COVER.
3. REMOVE 2 SCREWS AND LIFT OUT DEFECTIVE INTEGRATOR OR AMPLIFIER.
4. INSTALL NEW AMPLIFIER OR INTEGRATOR AND SECURE WITH 2 SCREWS.
5. TEST AND NULL NEW UNIT(S) AS INDICATED IN TEST SET PROCEDURE (TABLE 10-3).
6. CLOSE AND LATCH COVER ASSEMBLY.
WE 11265A
Figure 10-5. Removal/installation - amplifier integrator assembly
10-10
C8, TM 9-2350-230-12
Figure 10-6. Removal/installation - motor-generator assembly
10-10.1
C8, TM 9-2350-230-12
Figure 10-6.1. Removal/installation - motor generator brushes (1 of 2)
10-10.2
C8, TM 9-2350-230-12
Figure 10-6.2. Removal/installation - motor generator brushes (2 of 2)
10-11
C8, TM 9-2350-230-12
(REFER TO FIGURE 10-7.1 FOR DUAL MOUNTING POSITION
Figure 10-7. Removal/installation - commander’s or gunner’s control handle assembly,

and grenade launcher control box
10-12
C6, TM 9-2350-230-12
Figure 10-7.1. Removal/installation - commander’s control handle dual position

mounting brackets.
10-12.1
(10-12.2 Blank)
C4, TM 9-2350-230-12
PRELIMINARY STEP
TURN TURRET POWER AND VEHICLE MASTER

SWITCHES TO "OFF" POSITION.
REMOVAL
1. ELECTRICAL CONNECTOR
(USE PLIERS - 5120-908-6339).
2. SCREWS AND WASHERS (4)
3. POWER SUPPLY ASSEMBLY
INSTALLATION
REVERSE REMOVAL PROCEDURE. PERFORM TEST

SET SYSTEM CHECK (TABLE 10-3).
WE 11160
Figure 10-8. Removal/installation/test - power supply assembly
PRELIMINARY STEPS
TURN TURRET POWER AND VEHICLE MASTER

SWITCHES TO "OFF" POSITION.
REMOVAL
I. ELECTRICAL CONNECTOR (3)

(USE PLIERS- 5120-9086339)
2. SCREW AND WASHER (2)
3. GYRO SELECTOR
INSTALLATION
REVERSE REMOVAL PROCEDURE. PERFORM TEST

SET SYSTEM CHECK (TABLE 10-3).
WE 11179
Figure 10-9. Removal/installation - gyro selector assembly
10-13
C4, TM 9-2350-230-12
Figure 10-10. Removal/installation - elevating and traverse mechanism clutch brush
Figure 10-11. (Superseded) Removal/installation - elevating and traverse mechanism servo mo
10-14
TM 9-2350-230-12
Figure 10-12. Adjusting gun-launcher elevation and depression bump stops
10-15
TM 9-2350-230-12
Figure 10-13. Adjusting gun-launcher depression control
10-16
C6, TM 9-2350-230-12
Section 10-3. CONVENTIONAL WEAPONS DATA
10-3. General (1) Azimuth indicator section 11-3 of chapter 11.
a. This section contains organizational (2) Gunner’s or commander’s control handle table
maintenance instructions for the conventional weapons 10-2.
system components listed in table 10-4. (3) Gun and turret control selector support
b. The following components are not part of, but maintenance.
have functional operation with turret conventional
weapons system. c. Refer to figure 10-1 and table 10-1 for locational
reference of conventional weapons system components.
ASSEMBLY OR COMPONENT FIGURE REFERENCE

TEST ADJUST REMOVE/INSTALL
Relay Box 10-14
Breech Scavenge Repeat Switch 10-14
Loader’s Control Box 10-14
Blasting Machine 10-16
120 Volt Firing Circuit Power Supply 10-16.1
Safe-to-fire Indicator Switch 3-2
Figure 10-14. Removal/installation - relay box and loader’s control box.
10-17
C9, TM 9-2350-230-12
Figure 10-15. Removal/installation - M119 or #127 telescope emergency power

supply battery box
Figure 10-16. Removal/installation - gun-launcher blasting machine

(impulse generator).
10-18
C 13, TM 9-2350-230-12
Figure 10-16.1. Removal/installation - unserviceable

120 volt dc firing circuit power supply.
Figure 10-16.2. Minor alteration of unserviceable 120

volt dc firing circuit power supply.
10-18.1
C 9, TM 9-2350-230-12
Figure 10-17. Disassembly/assembly - low pressure

air radiator cleaning system.
10-18.2
C 11, TM 9-2350-230-12
Figure 10-17.0. Identification and location of

guards and CBSS parts.
(10-18.4 blank)/10-18.3
C12, TM 9-2350-230-12
Figure 10-17.1. Removal/installation - breech scavenging compressor

10-19
C 11, TM 9-2350-230-12
Figure 10-17.1.1. Compressor identification

Figure 10-17. 2 - deleted.
10-20
C 9, TM 9-2350-230-12
Figure 10-17.3. Removal/installation - chemical air drier cartridge
10-20.1
C 10, TM 9-2350-230-12
Figure 10-17. 4. Removal/cleaning/installation - compressor air intake

strainer and filter.
10-20.2
C 10, TM 9-2350-230-12
Figure 10-17.5. Removal/installation - dipstick and oil strainer
10-20.3
C 11, TM 9-2350-230-12
Section 10-4. MISSILE SUBSYSTEM
10-4. General condition exists before proceeding with transmitter

alignment check.
a. This section contains instructions for
organizational maintenance of the missile subsystem as (2) Set vehicle master switch to ON position.
listed in table 10-5. Turn selector on gun and turret control
panel to MISSILE position.
b. Refer to figure 10-1 and table 10-1 for
identification and locational reference of components of WARNING: Make certain weapons are unloaded or
the subsystem. deactivated and POWER selector on panel is in OFF
position to prevent injury to personnel during
10-5. Checks and Adjustments performance of transmitter alignment check. Do not look
into transmitter lens, eye damage may result.
a. General. Perform subsystem checkout
procedures outlined in table 2-12 before making checks (3) Open transmitter door and install
and adjustments to components of the subsystem. The telescopic viewer with swivel clip of range
transmitter alignment check will be performed quarterly measuring cord to lower eye hook of
or whenever alignment becomes questionable for any telescopic viewer thumb screw (fig. 10-
reason. 20).
b. Transmitter Alignment Check. The transmitter (4) Attach adapter plate to external end of
alignment check procedure insures that the transmitter gunner’s telescope mount.
sees the same target image as the telescope missile
reticle. To check transmitter alignment use transmitter (5) Move downrange until measuring cord is
alignment test set M45 (4935-999-2187) or M45A1 taut. When using the M45Altest set, pivot
(4935-045-9864) and proceed as follows: the target board so that it and the stake
are in vertical alignment. Position target
(1) Perform subsystem checkout procedures board in socket on test set carrying case
(table 2-12) to make sure a GO cover.
Table 10-5. Missile Subsystem Components

Figure Reference
Assembly or Component Check Replace
Cable Assembly Interconnection Diagram 10-18
Signal Data Converter 10-19
Modulator 10-19
Infrared Transmitter Cover and Door Latch and Control 10-21
Assemblies (Refer to para 10-17. 2 for adjustments)
Infrared Transmitter (Refer to para 10-5 for alignment check) 10-20, 10-22
10-20.1
Subsystem Power Supply 10-23
Rate Sensing Unit 10-24
Remote Control Components Test Set 10-25
Infrared Tracker 10-26
10-20.4
C14, TM 9-2350-230-12
(6) Using manual elevating and traversing 10-7. Cable Assemblies

handles, place missile reticle of gunner’s When removal and replacement of a unit suspected
telescope over center of target board (fig. of being defective does not correct a NO/GO situation,
10-20). When using the M45A1 test set, the cable assemblies to the unit may be at fault.
place the missile reticle of the gunner’s Examine cable assemblies (fig. 10-18) to the unit for
telescope over the center of the upper loose, broken, or incomplete connections. Repeat
target on the target board as shown in subsystem checkout procedures (table 2-12). If the
figure 10-20.1. NO/GO condition still exists, notify support maintenance
personnel.
CAUTION: When sighting through telescopic viewer
do not rest weight on transmitter, or gun shield. 10-7.1. Installation of RFI Filters
(7) Sight through telescopic viewer and a. RFI filters 8035602 and 8035603 will be issued
determine whether center of target board to all units. These filters must be installed on the optical
is within the 6-milliradian circle of the tracker as specified below. When the vehicle is removed
viewer (fig. 10-20 and 10-20.1) If center of from service, the filters must be r e m o v e d and
target board is not inside the 6-milliradian installed o n the replacement vehicle.
circle, replace transmitter. Should
replacement transmitter give the same (1) Disconnect W6P2 and W5P2 at the
result, refer to support maintenance. tracker.
(8) Remove adapter plate and telescopic
viewer from vehicle. Wind up measuring CAUTION: Do not damage the connector pins.
cord on target board and stow all Exercise care when installing the filters and when
equipment in carrying case. Close connecting W6P2 and W5P2.
transmitter door.
(2) Install filter 8035602 on connector 2J1 and
10-6. Removal and Installation filters 8035603 on connector 2J2.
Procedures illustrated in this section list the proper (3) Connect W6P2 to filter 8035603 (2J2) and
steps to be followed when removing and installing W5P2 to filter 8035602 (2J1).
components of the missile subsystem. Refer to figure
10-1 and table 10-1 for location of the items in the turret. b. Perform system self test (table 2-12) to insure
the missile system is in a "GO" condition.
10-21
TM 9-2350-230-12
Figure 10-18. Missile subsystem cable assembly interconnection diagram
10-22
C 10, TM 9-2350-230-12
Figure 10-19. Removal/Installation - signal data converter and modulator

10-23
C1, TM 9-2350-230-12
Figure 10-20. Transmitter alignment check
10-24
C8, TM 9-2350-230-12
Figure 10-20.1. Transmitter alignment with M45A1 test set
10-24.1
C 11, TM 9-2350-230-12
Figure 10-21. Removal/installation - infrared transmitter cover and disassembly/

assembly of door latch and control assemblies.
10-24.2
C 11, TM 9-2350-230-12
10-7.2. Adjustment of Control Assembly and Door Catch (1) If door remains tight against cover, catch
(15) adjustment is correct. Tighten nuts (14) 9 to 10
a. Cable Length Adjustment (Fig 10-21). foot-pounds.
(1) Push handle of control assembly (21) in (2) If door will not open, but is not held tightly
against bracket (22) and turn 90° either direction. against cover, move catch back (approximately the
distance catch permits door to open). Repeat test until
(2) Hold door in maximum open position and door latches tightly against cover. Tighten nuts (14) 9 to
adjust rod end (12) to align with hole in door latch 10 foot-pounds.
assembly (3).
(3) If door opens, latch did not engage catch.
(3) Turn rod end counterclockwise one or one Move catch forward and tighten nuts. Repeat test until
and one-half turns to provide tension; tighter nut (13) door latches tightly against cover. Tighten nuts (14) 9 to
against rod end. 10 foot-pounds.
(4) Secure rod end to latch assembly with (c). Final Adjustment. After completing cable length
straight pin and cotter pin (1). adjustment and door catch adjustments (a and b
above), open and close door with handle several times to
b. Door Catch (Fig 10-21). assure proper operation. Then adjust door switch (fig
10-22).
NOTE. Test adjustment of catch by closing door
with handle, leaving handle in unlocked position.
Attempt to pull door open.
10-25
C 11, TM 9-2350-230-12
Figure 10-22. Removal/installation - infrared transmitter and door switch.
10-26
C 10, TM 9-2350-230-12
Figure 10-23. Removal/installation - missile subsystem power supply
Figure 10-24. Removal/installation - rate sensing unit.
10-27
C 10, TM 9-2350-230-12
Figure 10-25. Removal/installation - missile subsystem test checkout panel
Figure 10-26. Removal/installation - optical tracker
10-28
C 14, TM 9-2350-230-12
Section 10-5. ACCESSORY AND POWER SYSTEM
NOTE. All references to M551A1 in this section pertain to vehicles equipped with laser range
finder.
10-8. General c. Refer to figure 10-1 and

table 10-1 for identification
a. This section contains of electrical accessory and.
Organizational maintenance in- power system components.
Structions for the accessory
and power system components d. Refer to TM 11-5820-401-
listed in table 10-6 20 for maintenance instructions
covering radio and intercom equipment.
b. (Deleted)
Table 10-6. Turret Electrical Accessory and Power System Components

Figure reference
Assembly or component Remove/install Repair
Circuit Cutout Box..................................................................................................... 10-27 19-27
Gas-Particulate Filter Unit ........................................................................................ 10-30 10-31
Dome Lights ............................................................................................................. 9-95 9-96
Antennas (front or rear) ............................................................................................ 10-32
Cupola Control Box .................................................................................................. 10-33
Cupola Control Assembly......................................................................................... 10-34
Ventilating Fan (Co.-Ax Fume Control) .................................................................... 10-35
Grenade Launcher Control Box................................................................................ 10-7
Grenade Launcher Power Supply ............................................................................ 10-35.1
Cupola/Laser Control Box Assembly
(M551A1 only) ..................................................................................................... 10-35.2
Remote Switch Assembly (M551A1 only) ................................................................ 10-35.3
Resistor Box Assembly (17551A1 only) ................................................................... 10-35.4
10-29
C 14, TM 9-2350-230-12
Figure 10-27. Removal/installation - circuit cutout box.
10-30
C14, TM 9-2350-230-12
Pages 10-32.1 and 10-32.2 including figures 10-28 and 10-29 - deleted.
Figure 10-30. Removal/installation - air filter unit, air purifier, frame and step
plate
(10-31 blank)/10-32
TM 9-2350-230-12
Figure 10-31. Disassembly/cleaning/inspection/assembly - air filter unit
10-33
C6, TM 9-2350-230-12
Figure 10-32. Removal/installation - radio antenna - front or rear
10-34
C 13, TM 9-2350-230-12
Figure 10-33. Removal/installation - cupola/laser control box assembly (M551A1only).
Figure 10-34. Removal/installation - remote switch assembly (M551A1 ONLY).
10-36.1
C 8, TM 9-2350-230-12
Figure 10-35. Removal/installation - resistor box assembly (M551A1 only).
10-36.2
C 14, TM 9-2350-230-12
Figure 10-33. Removal/installation - cupola control box.
Figure 10-35.3. Removal/installation - cupola control assembly.
10-35
C 8, TM 9-2350-230-12
Figure 10-35. Removal/installation - turret ventilating fan.
Figure 10-35.1. Removal/installation - grenade launcher power supply box.
10-36
C 13, TM 9-2350-230-12
Section 10-6. TURRET COMPONENTS
NOTE. ALL references to M551Al in this section pertain to vehicles equipped with laser. range
finder.
10-9. General structions for turret and cupo-

la components listed in table
a. This section contains 10-7.
organizational maintenance in-
Table 10-7. Turret Components Figure reference
Figure reference
Assembly or component Remove/install Repair
Traverse Lock................................................................................................................. 10-36 10-36

7.62-MM Machine Gun Ammunition
Feed System ............................................................................................................. 10-37
Commander’s Seat......................................................................................................... 10-38 10-39
Gunner’s Seat................................................................................................................. 10-40 10-41
Loader’s Seat and Back Rest......................................................................................... 10-42 10-42
Turret Cable Guards....................................................................................................... 10-43
Loader’s Hatch Cover..................................................................................................... 10-44 10-44
Conventional Ammunition Horizontal Racks .................................................................. 10-45 10-45
Conventional Ammunition Vertical Racks ...................................................................... 10-46 10-46
Turret Missile Rack and Portable
Fire Extinguisher........................................................................................................ 10-47
Gunner’s Leg Guard....................................................................................................... 10-48
Cupola Vision Blocks...................................................................................................... 10-49
Telescope Protective Shield........................................................................................... 10-49.1
Cal .50 Machine Gun Mount Support
Assembly ................................................................................................................... 10-49.2
Commander’s Ballistic Shield Plate
Assemblies ................................................................................................................ 10-49.3,
10-49.4
Turret Interior Stowage................................................................................................... 10-50
Turret Exterior Stowage ................................................................................................. 10-52
Turret Floor Access Cover ............................................................................................. 4-3
Cupola Seal for Transceiver (PM55lAl only)................................................................... 10-53
Loader’s Periscope Stop (M551Al only) ......................................................................... 10-54
Index Pointers (M551A1 only) ........................................................................................ 10-55
Laser Control Handle (M551Al only) .............................................................................. 10-56
Cable Covers (M551A1 only) ......................................................................................... 10-57
Electronics Unit and Power Supply
Covers (M551A1 only)............................................................................................... 10-58
Commander’s Ballistic Shields (M551A1
only)........................................................................................................................... 10-59
10-36.3
C 9, TM 9-2350-230-12
Figure 10-36. Removal/disassembly/assembly/ installation - turret traverse lock.
10-36.4
C 11, TM 9-2350-230-12
Figure 10-37. Removal/installation - 7. 62-mm machine gun ammunition feed system.
10-37
C4, TM 9-2350-230-12
Figure 10-38. Removal/installation - commander’s seat assembly
10-38
C3, TM 9-2350-230-12
Figure 10-39. (Superseded) Disassembly/assembly - commander’s seat assembly
10-39
C3, TM 9-2350-230-12
Figure 10-40. (Superseded) Removal/installation - gunner’s seat assembly
10-40
C3, TM 9-2350-230-12
Figure 10-41. (Superseded) Disassembly/assembly - gunner’s seat assembly
10-41
C3, TM 9-2350-230-12
Figure 10-42. (Superseded) Removal/installation - loader’s seat and backrest
10-42
C 11, TM 9-2350-230-12
Pages 10-42. 1 and 10-42. 2, including figures 10-42. 1 and 10-42. 2 - deleted.
Figure 10-43. Removal/installation - turret cable guards.
10-43
C 11, TM 9-2350-230-12
Figure 10-44. Removal/installation - loader’s hatch cover and components
10-44
C 11, TM 9-2350-230-12
Figure 10-45. Removal/installation/repair - turret conventional ammunition horizontal racks.
10-45
C 11, TM 9-2350-230-12
Figure 10-46. Removal/installation/repair - turret conventional ammunition vertical racks.
10-46
C 11, TM 9-2350-230-12
Figures 10-47.1 and 10-47.2 - deleted.
10-47
C 11, TM 9-2350-230-12
Figure 10-49. Removal/installation - cupola vision blocks
Pages 10-48.1 and 10.48.2 - deleted.
10-48
C8, TM 9-2350-230-12
Figure 10-49.1. Removal/installation - Telescope protective shield
10-48.3
C12, TM 9-2350-230-12
Figure 10-49.2.1. Removal/installation - cupola traverse switch assembly.
10-48.4
C13, TM 9-2350-230-12
Figure 10-49.3. Removal/installation - commander’s ballistic shield plate assemblies (1 of 2).
10-48.4.2/ (10-48.4.1 blank)

C9, TM 9-2350-230-12
SIDE AND FRONT SHIELDS INSTALLED ELECTRICAL CONNECTOR DETAIL
REAR ENCLOSURE INSTALLED SPENT BRASS DEFLECTOR INSTALLED
CIRCLED NUMBERS ABOVE REFER TO LEGEND, FIGURE 10-49.3
Figure 10-49.4. Removal/installation - commander’s ballistic shield plate assemblies (2 of 2).
10-48.5
C11, TM 9-2350-230-12
Figure 10-50. Turret interior stowage.
Figure 10-51 - deleted.
10-48.6
C11, TM 9-2350-230-12
Figure 10-52. Turret exterior stowage
10-49
C 13, TM 9-2350-230-12
Figure 10-54. Removal/installation - loader’s periscope stop (M551A1 only).
10-50
C 13, TM 9-2350-230-12
Figure 10-55. Removal/installation - index pointers (M551a1 only).
Figure 10-56. Removal/ installation - laser control handle (M551A1 only).
10-51
C 13, TM 9-2350-230-12
Figure 10-57. Removal/installation - cable covers (M551Al only).
10-52
C 13, TM 9-2350-230-12
Figure 10-58. Removal/installation - electronics unit and power supply covers (M551A1 only).
10-53
C 13, TM 9-2350-230-12
Figure 10-59. Removal/installation - commander’s ballistic shields (M551A1 only).
10-54
C 12, TM 9-2350-230-12
CHAPTER 11
ORGANIZATIONAL MAINTENANCE-ARMAMENT
AND FIRE CONTROL
Section 11-1. PRIMARY ARMAMENT
11-1. General C "Prevailing Torque", as used in this chapter,

is the force required to turn a self-locking screw or nut
a. Table 11-1 lists components of the M81 in/on its mating threads before the screw head or nut
modified and M81E1 gun-launcher, including the comes in contact with the surface against which it is
compressed air closed-breech scavenging system, and being tightened. It is a result of the self-locking feature
mount which are serviced by organizational maintenance of the screw or nut.
personnel. To simplify maintenance procedures, allowance
for prevailing torque, where applicable, has been
b. Refer to figures 11-1 and 11-11 for incorporated in torque values specified. Torque values
locational reference and component identification. which include prevailing torque are so identified in the
instructions.
TABLE 11-1. PRIMARY ARMAMENT
FIGURE REFERENCE
ASSEMBLY OR COMPONENT REMOVE/
ADJUST INSTALL REPAIR
Firing Mechanism Continuity Check-Table 11-2
Firing Mechanism Continuity 11-1.4
Counterrecoil Buffer and In-Battery Limit Switch 11-2 11-2
7.62-MM Machine Gun Mount 11-3
7.62-MM Machine Gun Spent Brass Chute and Bag 11-4
Recoil Mechanism Hand Pump and Hydraulic 11-5 11-5
Fittings
Filling and Bleeding Recoil Hydraulic System Table 11-2.2

Buffer Bleed Line 11-5.1
Recoil Guard Cover and Screen 11-6
Recoil Mechanism Reservoir Components 11-7, 11-7,
11-8 11-8
Breech Scavenging Check Valve 11-10.1 11-10.2,
11-10.3
CBSS Slaving System 11-10.1.1
Wiring Harness Assembly 11-12
Breech Open/Closed Switches 11-12
Firing Mechanism 11-13
Electric Drive Motor 11-14
Electric Drive Solenoid 11-15
Loading Tray and Bracket Assembly 11-16 11-17,
11-18;
11-19
Loading Tray and Ejector 11-20
Loading Tray Guide 11-21 11-21
Ejector Cocking Bracket 11-21 11-21
Ammunition Detent 11-23 11-22
Obturator Gasket 11-24
Carrier Cover Vent Plug 11-25
Manual Drive Crank Handle 11-25
11-1
C 10, TM 9-2350-230-12
TABLE 11-2. FIRING MECHANISM CONTINUITY CHECK

STEP PROCEDURE
1 Remove guard, upper harness clamp, and electrical connector from firing mechanism receptacle (fig. 11-1.4).
2 Open breech chamber and short the firing mechanism tip to firing mechanism collar or breech chamber.
NOTE: Firing mechanism tip can be shorted to collar by wrapping lockwire around the tip and firing mechanism
collar.
3 Manually close breech until scribe line on breech chamber is between the "SAFE" scribe lines on coupling.
4 Connect a continuity light or multimeter to the two pins in firing mechanism receptacle.
5 Circuit between receptacle pins must show continuity, if not adjust receptacle (fig. 11-1.4 ).
6 If light or meter indicates continuity, remove light and open breech. Remove shorting wire and install
harness connector, harness clamp, and guard.
Figure 11-1. Gun mount assembly for gun-launcher - locational reference.
Figures 11-1.1, 11-1.2, and 11-1.3 deleted.
11-2
C 10, TM 9-2350-230-12
Figure 11-1. 4. Adjusting firing mechanism receptacle for continuity.
(11-2.2 blank)/11-2.1
C9, TM 9-2350-230-12
Figure 11-2. Removal/installation - counterrecoil buffer, and adjusting in-battery limit switch
11-3
C8, TM 9-2350-230-12
TABLE 11-2.1. PROCEDURE FOR CYCLING CBSS

STEP PROCEDURE
1 Check oil in air compressor.
2 Turn on compressor and fill air bottles.
3 Turn manual shut off valve to "ON" position.
4 Remove one mounting screw and loosen the other screw of the in-battery switch bracket, and
swing up out of contact with the actuator screw (see fig. 11-2).
NOTE. Do not disturb the setting of switch attachment to bracket.
5 To cycle CBSS, depress plunger of in-battery switch.
WARNING: When 1. 7 second surge of air is completed the breech chamber opens
automatically. All personnel must make certain to stand clear to prevent injury.
6 After completion of CBSS cycling SHUT OFF turret power and return in-battery
switch bracket to original position, replace screws, and tighten.
11-4
C8. TM 9-2350-230-12
Figure 11-3. Removal/Installation-7.62mm machine gun mount
(11-4. 2 Blank) 11-4.1

C4, TM 9-2350-230-12
Figure 11-4. (Superseded) Removal/installation - M73 machine gun ammunition spent brass chute and bag
11-5
C8, TM 9-2350-230-12
Figure 11-5. Removal/installation - recoil mechanism hand pump and hydraulic fittings
11-6
C8, TM 9-2350-230-12
Figure 11-5.1. Removal/Installation - buffer bleed line
TABLE 11-2.2 FILLING AND BLEEDING GUN MOUNT HYDRAULIC SYSTEM

STEP PROCEDURE
NOTE. Refer to figure 3-2.
1 Position gun at zero elevation. Remove plug from top rear port on recoil cylinder and disconnect bleed line at
elbow fitting to exhaust air while filling recoil mechanism.
2 Disconnect hand pump outlet-to-check valve pressure line at check valve on bottom rear of recoil guard.
3 Connect a separate hydraulic fluid supply to check valve, depress recoil mechanism 3-5 degrees and fill with
hydraulic fluid filtered to 5 microns, Specification MIL-H-6083 (OHC).
4 When. fluid flows from elbow fitting, reconnect bleed line. Continue filling until fluid flows from top rear port.
5 Install plug in top rear port.
6 Elevate recoil mechanism to zero degrees. Remove filling plug in top of replenisher reservoir. Open manual
bleed valve and continue filling until replenisher reservoir fluid level is at bottom of filling plug opening.
Reinstall filling plug.
7 Operate replenisher pump until clear fluid flows from pump pressure line. This will fill and bleed suction line,
pump assembly, and pressure line.
7.1 Units with buffer bleed: Remove front plug from counter recoil buffer to bleed air from buffer. Replace plug
when oil flows out. Check oil level in replenisher and repeat step 6 if required.
8 Remove connection from separate fluid supply and re-attach hand pump pressure line to check valve.
9 Operate hand pump several times to remove any additional air in suction and pressure lines. Depress recoil
mechanism 5 degrees and let stand for 20 minutes. At end of this time, crack plug in top rear port and bleed
off any additional entrapped air by operating hand pump.
11-6.1
C6, TM 9-2350-230-12
11-6.2
C 10, TM 9-2350-230-12
Figure 11-6. Removal/installation - recoil guard cover and screen
11-7
C10, TM 9-2350-230-12
Figure 11-7. Removal/installation - recoil mechanism reservoir components (1 of 2)
11-8
C 14, TM 9-2350-230-12
Figure 11-8. Removal/installation recoil mechanism reservoir components (2 of 2).
Figures 11-9 and 11-10--deleted.
11-9
C 10, TM 9-2350-230-12
Figure 11-10.1. Removal/installation - breech scavenger check valve.
Pages 11-10.1 and 11-10.2--deleted.
11-10
C 12, TM 9-2350-230-12
Figure 11-10.1.1. Removal/installation of CBSS slaving system.
11-10.3
C6, TM 9-2350-230-12
Figure 11-10.2. Disassembly/cleaning/assembly - breech scavenger check valve (1 of 2).
11-10.4
C6, TM 9-2350-230-12
Figure 11-10.3. Disassembly/cleaning/assembly - breech scavenger check valve (2 of 2)

11-11
C2, TM 9-2350-230-12
Figure 11-11. M81 gun-launcher breech assembly and components - reference
11-11
C10, TM 9-2350-230-12
Figure 11-12. Removal/installation - gun-launcher electrical wiring harness and breech limit switches
11-13
C 14, TM 9-2350-230-12
Figure 11-13. Removal/installation - gun-launcher firing mechanism assembly.
11-14
C6, TM 9-2350-230-12
Figure 11-14. Removal/installation - breech electric drive motor assembly
11-15
C9, TM 9-2350-230-12
Figure 11-15. Removal/installation - breech electric drive solenoid
Figure 11-16. Removal/installation - loading tray bracket assembly
11-16
C6, TM 9-2350-230-12
Figure 11-17. Disassembly/assembly - loading tray bracket assembly (1 of 3)
11-17
C6, TM 9-2350-230-12
Figure 11-18. Disassembly/assembly - loading tray bracket assembly (2 of 3)
11-18
C 14 TM 9-2350-230-12
Figure 11-19. Disassembly/assembly - loading tray bracket assembly (3 of 3).
11-19
C 13, TM 9-2350-230-12
Figure 11-20. Adjustment - loading tray and ejector.
11-20
C9, TM 9-2350-230-12
Figure 11-21. Removal/installation - loading tray guide and ejector cocking bracket
11-21
C 14, TM 9-2350-230-12
Figure 11-22. Removal/installation ammunition detent and components (early design--type I).
11-22
C 14, TM 9-2350-230-12
Figure 11-23. Cleaning/inspection/adjustment trigger lever and early design (type I) ammunition detent.)
11-23
C 14, TM 9-2350-230-12
Figure 11-23.1. Removal/installation ammunition detent assembly (late design--type II).
11-24
C 14, TM 9-2350-230-12
Figure 11-23.2. Disassembly/assembly ammunition detent (late design--type II) and housing assembly.
11-24.1
C 14, TM 9-2350-230-12
Figure 11-23.3. Cleaning/inspection/adjustment trigger lever and late design ammunition detent (type III).
11-24.2
C 10, TM 9-2350-230-12
Figure 11-24. Removal/installation - obturator seal’
Figure 11-25. Removal/installation carrier cover vent plug and manual drive crank handle.
(11-24. 4 blank)/11-24. 3
C 11, TM 9-2350-230-12
Section 11-2. SECONDARY ARMAMENT
11-2. General 11-3. Machine Gun Cleaning Instructions
This section contains instructions for organizational a. Refer to TM 9-1005-233-25 for maintenance 7.
maintenance of the M176 grenade launcher mounts as 62-mm machine gun M73, M73A1, or M219.
shown in table 11-3.
b. Refer to TM 9-1005-213-25 for maintenance of
cal. 50 machine gun M2.
TABLE 11-3. M176 GRENADE LAUNCHER
FIGURE REFERENCE
REMOVE/INSTALL ADJUST
Tube Assembly 11-25.3

Solenoid 11-25.4
Table 11-4 and figures 11-25.1 and 11-25. 2 - deleted.
11-25
C 10, TM 9-2350-230-12
PRELIMINARY STEPS
A. OBTAIN TWO 3/8 HEXAGON TOOL STEEL PIECES, APPROXIMATELY 6 INCHES
AND 2 INCHES IN LENGTH, TO FACILITATE REMOVAL AND INSTALLATION
OF MOUNTING SCREWS.
B. TURN GRENADE LAUNCHER CONTROL PANEL MASTER SWITCH OFF AND
INSTALL SAFETY WIRE.
C,TURN CONTROL PANEL FIRE SWITCH OFF AND INSERT SAFETY PIN.
D, REMOVE LAUNCHER FROM TUBE ASSEMBLY (FIG. 3-15.1).
E. REMOVE CABLE CHANNEL AND DISCONNECT SOLENOID LEAD.
REMOVAL
1. REMOVE 2 UPPER MOUNTING SCREWS AND WASHERS (AND SHIMS IF PREVIOUSLY
USED) USING 2 INCH HEXAGON TOOL.
2. USE 6 INCH HEXAGON TOOL TO REACH LOWER SCREWS THROUGH UPPER
BRACKET HOLES. REMOVE 2 SCREWS, WASHERS (AND SHIMS IF PREVIOUSLY
USED) AND TUBE ASSEMBLY.
INSTALLATION
1. HOLD TUBE ASSEMBLY IN PLACE AGAINST BRACKETS AND INSTALL LOWER
SCREWS AND LOCK WASHERS. TIGHTEN TO 5 TO 10 POUNDS-FEET.
2. INSTALL ONE TOP SCREW AND LOCK WASHER AND TIGHTEN TO 5 TO 10
POUNDS-FEET.
3. USE FEELER GAGE TO DETERMINE WHERE SHIMS ARE NECESSARY, AND
THICKNESS OF SHIMS REQUIRED.
4. REMOVE SCREWS AS NECESSARY TO INSTALL SHIMS, THEN INSTALL
BOTTOM SCREWS AND LOCK WASHERS FIRST. KEEP ONE UPPER SCREW
IN PLACE WHILE TIGHTENING BOTTOM SCREWS TO MAINTAIN ALIGNMENT
OF TUBE ON BRACKET. TIGHTEN BOTTOM SCREWS TO 75 POUNDS-FEET.
5. INSTALL UPPER SCREWS AND LOCK WASHERS, WITH SHIMS AS REQUIRED.
TIGHTEN TO 75 POUNDS-FEET.
6. CHECK SOLENOID ADJUSTMENT (FIG. 11-25.4).
7. CONNECT SOLENOID ELECTRICAL LEADS AND INSTALL CABLE CHANNEL
(FIG. 11-25.4).
WE 70041 I
Figure 11-25. 3. Removal/Installation - grenade launcher tube assembly.
11-26
C 11, TM 9-2350-230-12
Figure 11-25.4. solenoid adjustment- grenade launcher tube assembly.
Figures 11-26 thru 11-34—deleted
11-27
C 14, TM 9-2350-230-12
Section 11-3. SIGHTING AND FIRE CONTROL
11-4. General (2) Open escape port of the unit to be

purged (except on the receiver-transmitter) by removing
a. This section contains organizational the plug screw. The receiver-transmitter has a relief
maintenance instructions for the sighting and fire control valve and does not require removal of a plug screw. The
components. Refer to table 11-5 for figure references to relief valve will pop open when a pressure greater than 4
maintenance of all components on the M551. See psi is applied to it.
paragraph 11-5 for instructions for purging the laser
range finder units on the M551A1. (3) Using the appropriate adapter, attach one
end of the purging adapter kit to the nitrogen cylinder and
b. Refer to table 11-6 for instructions on the other end to the fill valve or entrance port.
synchronization of XM)44 series periscope and linkage,
using an outdoor method. (4) Turn the tank valve on the nitrogen
cylinder counterclockwise to open.
c. Refer to TMs 9-2350-23010/2-1 and 9-2350-
230-10-2-3 for boresighting procedures on all sighting (5) Set the pressure regulator to 7 psi +2
and fire control instruments on the M551 and M551A1,
respectively. (6) Open control valve on the purging adapter
kit to allow nitrogen to flow through the unit for
11-5. Purging Laser Range Finder Units (M551A1 approximately 10 minutes for all units except the
Only) receiver-transmitter. Allow nitrogen to flow through the
receiver-transmitter for 30 minutes.
a. Laser range finder units must be purged with dry (7) Close the control valve on the purging
nitrogen at 90-day intervals to prevent condensation of kit.
moisture. (8) Remove the purging adapter kit from
b. Use purging adapter kit supplied for the M551 the laser range finder unit.
series vehicles. (9) Immediately reinstall valve cap (at fill
c. The fill valve (or entrance port) on each unit is valve) on receiver-transmitter; on other units, install plug
color-coded gray; the relief valve (or escape port), yellow. screws at entrance and escape ports.
d. Purge the laser range finder units as follows:
(1) Remove the fill valve cap or plug screw

from the unit fill valve (or entrance port).
11-28
C 14, TM 9-2350-230-12
(10) Close valve on the by opening its valve and turn-

nitrogen tank. Relieve pres- ing the pressure regulator con-
sure in the purging equipment trol counterclockwise until
regulator gages indicate zero.
Table 11-5. Sighting and Fire Control Components
FIGURE REFERENCE
Service remove / Install
ASSEMBLY OR COMPONENT adjust Replace
M37 Loader’s Periscope Mount 11-35

and Seal
M47/48 Driver’s Periscope, 11-36 11-36

Mount, Seal, and Wiper
M47/48 Driver’ s Periscope 11-37

Washer, Pump, and Re-
servoir
Azimuth Indicator and 11-38

Switch Assembly
M1A1 Gunner’s Quadrant 2-28
M119 or M127 Telescope Head- 11-40

rest, Hanger, and Telescope
M149 or M165 Telescope Mount 11-40.1
Telescope 1Mount Mounting 11-40.1.1

Bracket Bolts
M13A1C Elevation Quadrant 2-28 11-40.2
XM44 Series Periscope Body 11-41,11-41.1

and Head
Servicing XM44 Series Peri- 11-41.3

scope Emergency Battery
XM44 Series Periscope 11-42

Washer, Pump, Reservoir,
and Wiper Blade
XM44 Series Periscope Linkage 11-43
Pages 11-31 and 11-32--deleted.
11-29/(11-30 blank)
C8, TM 9-2350-230-12
TABLE 11-6. SYNCHRONIZATION OF XM44/El PERISCOPE BY OUTDOOR METHOD
Step No. Procedure
1 Locate vehicle on level ground with rear of vehicle adjacent to an incline or ramp and approximately
1200 meters from a suitable target. The incline should be of an angle so that vehicle can be
positioned with the front end downward approximately 350 mils from horizontal. Target should be
near horizontal line of sight to avoid a large elevation angle.
2 Secure muzzle boresight (black thread) in reference marks on gun muzzle and secure with strap or
tape (A, Fig. 2-23).
3 Open breech and insert breech boresight assembly. Position right telescope of binocular M17A1 over
hole of breech boresight assembly and select a distant aiming point(1200 meters) with sharply
defined vertical and horizontal lines.
4 Prepare the gunner’s XM44/E1 periscope for use as follows:
CAUTION: Use XM44/E 1 periscope boresight aid (10516830) when boresighting in daylight.
Use dark position filter to prevent excessive light from damaging internal components.
a. Open the ballistic shield by depressing handle finger latch, actuating handle and
releasing finger latch. Install boresight aid.
b. Turn periscope light switch on XM44/E 1 periscope control panel to "ON" position.
CAUTION: Do not direct periscope toward sun when periscope is on; excessive
light will damage internal components.
c. Adjust headrest. View through eyepiece and select dark position filter with
filter lever.
d. Turn focus knob to maximum counterclockwise position and turn diopter knob
to obtain sharpest image on screen.
e. View image on screen for proper illumination and move filter lever to provide
most effective filter for image illumination.
f. Turn and adjust XM44E1 periscope control panel rheostat knob clockwise for
proper illumination of reticle pattern.
5 Lay the gun tube on the target aiming point by laying low to high without over-travel.
(Always lay gun low to high to eliminate backlash from the system.)
6 NOTE 1. Both boresight knobs contain spring loaded clutch teeth requiring "pull to
turn" operation. This feature provides accurate boresight retention.
Align vertical center line of reticle on aiming point by use of azimuth
boresight knob (fig. 2-26). Slip scale on face of knob to "4".
2. Both elevation and azimuth knobs have approximately 15 mils of adjustment

or approximately two turns of adjustment. One revolution of the knob is 8
mils. Each line between numbers is 0.1 mil.
11-33
C8, TM 9-2350-230-12
TABLE 11-6. SYNCHRONIZATION OF XM44/EI PERISCOPE BY OUTDOOR METHOD (Continued)
Step No. Procedure
7 Pull and turn elevation knob counterclockwise to end of travel. Set slip scale to "1"
Pull and turn knob to "4".
8 Set both eccentric micrometers on the elevation link assembly to zero (fig. 11-43).
Adjust elevation link until boresight reticle is on same aiming point as the gun tube.
To adjust link, loosen two screws on connector and link and turn tube. Tighten both
screws.
9 If necessary, make a final elevation adjustment with the adjusting knob on periscope.
Reset the slip scale to "4".
10 Using the M1A1 gunner’s quadrant placed on the breech block rail (A, fig. 2-28), ele-
vate gun to 89 mils (5 degrees).
11 Back vehicle up incline until bubble in gunner’s quadrant is centered (approximately).
12 Observe target through boresight aid pin hole and re-lay gun on target aiming point by
laying low to high without over-travel.
13 With elevation boresight knob on periscope, align boresight mark of telescope reticle
on the same aiming point as the cross threads of the gun tube.
14 Read and record the deviation from the initial boresight reading (4) on the elevation
boresight knob scales.
15 Repeat steps 11 through 16 with gunner’s quadrant settings of:
178 mils (10 degrees), 267 mils (15 degrees), 336 mils (19 degrees), and minus
124 mils (7 degrees depressed position).
16 Determine if deviations from initial readings exceed the maximum tolerance of 0.5
mil for synchronization at 0, 5, 10, 15 or 19 degrees elevation, and 7 degrees depres-
sion. If synchronization error exceeds 0.5 mil, return vehicle to position with the
maximum deviation and adjust periscope line of sight, by adjusting the eccentrics on
elevation link (fig. 11-43) so that one-half of error is removed.
NOTE. Inner and outer eccentrics must be -adjusted so that either red or white scales are aligned to
the same index on bo’ scales, i.e., red scale to red scale or white scale to white scale. From
zero setting adjusting both eccentrics into red scales will lengthen the linkage and adjusting
both eccentrics into white scales will shorten the linkage.
17 Recheck boresight deviation at minus 124 mils to plus 336 mils (steps 14 and 15). Deviation
now should be within tolerance at each elevation. If not, recheck steps 2 through 17.
18 If periscope cannot be synchronized, replace periscope (fig. 11-41).
19 Remove boresight equipment (steps 2, 3, and 4).
20 Turn turret control and fire control switches off. Lamps will go out.
21 Turn XM44/E1 periscope control panel rheostat knob fully counterclockwise, position
dark filter in place (XM44E1 - filter to "OFF" position) and turn control panel peris-
cope switch to "OFF" position.
22 Close XM44/E1 periscope ballistic shield.
23 Turn vehicle MASTER SWITCH to "OFF" position.
11-34
C3, TM 9-2350-230-12
Figure 11-35. Removal/disassembly/assembly/installation - M37 loader’s periscope mount and seal
11-35
C8, TM 9-2350-230-12
Figure 11-36. Removal/installation - driver’s M47/M48 periscope mounts, seals, and wipers
11-36
C9, TM 9-2350-230-12
Figure 11-37. Removal/installation - driver’s M47/M48 periscope washer, pump, and reservoir
11-37
C10, TM 9-2350-230-12
Figure 11-38. Removal/installation - azimuth indicator and switch assembly
11-38
C 14, TM 9-2350-230-12
Figure 11-39--deleted, see figure 11-40.2.
Figure 11-40. Removal/installation - Mll9 or M127 telescope headrest, hanger, and telescope.
11-39
C 10, TM 9-2350-230-12
Figure 11-40.1. Removal/installation - M149 or M165 telescope mount.
Figure 11-40.1.1. Inspection of telescope mount bracket bolts.
11-40
C 9, TM 9-2350-230-12
Figure 11-40. 2. Removal/installation - M13A1C elevation quadrant.
11-40. 1
Figure 11-41. Removal/installation - X M44 Series periscope body and head (I of 2)
11-40.2
C 10, TM 9-2350-230-12
Figure 11-41.1 Removal/installation - XM44 series periscope body and head (2 of 2)

Figure 11-41. 3. Servicing XM44 series periscope emergency battery
(11-40. 4 blank)/11-40. 3
C9, TM 9-2350-230-12
Figure 11-42. Removal/installation - XM44 Series periscope washer, pump, reservoir, and wiper blade
11-41
C9, TM 9-2350-230-12
I Figure
11-43. Removal/installation - XM44 Series periscope linkage
11-42
C 10, TM 9-2350-230-12
CHAPTER 12
SPECIAL PURPOSE KITS
Section 12-1. GENERAL

12-1. Scope cial purpose kits available for application to the M551
This chapter illustrates procedures for the installation vehicles by organizational maintenance personnel.
and allocated maintenance of spe-
Sections 12-2 and 12-3 including paragraphs 12-2 and 12-3 - deleted.
Section 12-4. ENGINE AND BATTERY WINTERIZATION KIT
12-4. General heater, engine, and battery heater by an electrically

a. The winterization kit, when installed, provides a driven coolant pump furnished with the kit.
standby coolant heating and circulating system for use c. Operating procedures are covered in Table 2-13.
during shutdown periods at ambient temperatures Troubleshooting procedures are listed in Table 8-4, items
between -25sF and -65 F. The coolant heater system 60 through 66.
serves the dual purpose of preventing freezing of battery d. Original installation of the kit is performed by
electrolyte, and of keeping the engine sufficiently warm support maintenance personnel.
to aid in starting. e. Removal, replacement and maintenance of
b. The system is electrically actuated from a control components of the kit are illustrated in figures 12-5
box located to the left of the driver. An electric fuel pump through 12-12.
delivers fuel from the vehicle center fuel supply tank into
the coolant heater where it is ignited in a combustion
chamber. Coolant is circulated through the
Section 12-5. LESS MISSILE SYSTEM KIT
12-5. General b. Additional components of the kit are installed to

a. The less missile system kit provides for the provide turret and weapon stabilization utilizing missile
removal of a portion of the missile subsystem from subsystem power supply and rate sensor. Additional
vehicles when assigned to specific fielding not requiring ammunition stowage is also provided when kit is installed
a missile subsystem. Production vehicles, serial No. 140 (Fig. 12-13).
through 223 and 740 through 885 were manufactured
less missile subsystem.
Section 12-6. MINE PROTECTIVE KIT
12-6. General installation is made by support maintenance personnel.

a. The mine protective kit consists of an armor
steel plate and aluminum spacer plate for the hull b. Removal of the kit is shown in figures 12-14 and
bottom, two armor steel side plates, and attaching 12-15.
hardware. Because of hull modification required to
accept the kit, original
Section 12-7 and figures 12-1, 12-2, 12-3, 12-4, 12-4. 1, and 12-4. 2 - deleted.
12-1
C 10 TM 9-2350-230-12
Figure 12-5. Removal/installation - vehicle winterization kit.
Pages 12-2.1 thru 12-6. 2 deleted.
12-2
C3, TM 9-2350-230-12
TABLE 12-1. REMOVAL/INSTALLATION--VEHICLE WINTERIZATION KIT COMPONENTS

(Refer to Figure 12-5)
Turn heater power supply off at control box in driver’s compartment (Figure 12-8).
COMPONET LEGEND
1. EXHAUST PIPE ASSEMBLY 35. CLAMP - MS35842-14

2. SCREW-MS90728-59 36. COOLANT PUMP
3. WASHER - 10910174-3 37. COOLING FAN LOWER RIGHT SHROUD
4. SCREW - MS90727-59 GROMMET
5. ROOF BRACKET 38. BUSHING - AN912-85
6. NUT - MS51968-9 39. THERMOSTAT - 7700453-1
7. WIRING HARNESS - COOLANT HEATER - 40. ADAPTER - MS24522-23
TO-ENGINE COMPARTMENT BULKHEA] 41. BATTERY HEATER-TO-COOLANT
8. COOLANT HEATER PUMP HOSE (24 INCHES LONG)
9. ELBOW- MS20822-4 42. BATTERY’HEATER
10. ELBOW - MS24518-7 43. NIPPLE - AN816-4-4
11. HOSE CLAMP - MS35842-11 44. FUEL PUMP INLET HOSE
12. COOLANT HEATER-TO-ENGINE HOSE 44-1. BATTERY HEATER INLET HOSE
(52-INCHES LONG) 45. COOLANT HEATER INLET HOSE
13. HEATER FUEL INLET HOSE (25 INCHES LONG)
14. SCREW - MS35207-270 46. BUSHING - AN912-75
15. WASHER - 27183-8 47. WASHER - 10941915-3
16. NUT - MS51967-3 47-1. WASHER - MS35334-2 (BOTTOM SCREW
17. WASHER - MS27183-10 RIGHT BRACKET)
18. SHOCK MOUNT 48. ELBOW - MS24519-7
19. SCREW - MS90728-5 49. SCREW - MS90721-61
20. WASHER,- MS35334-19 50. EXHAUST PIPE CLAMP
21. FUEL PUMP MOUNTING BRACKET 51. NUT - MS51968-3
22. FUEL FILTER MOUNTING BRACKET 52. WASHER - 1091017-1
23. ELECTRIC FUEL PUMP 53. EXHAUST PIPE BRACKET
24. ADAPTER - MS39206-3 54. SNUBBING WASHER - AN8013-D2
25. ELBOW- MS20823-4 55. HEATER RIGHT BRACKET
26. FUEL PUMP OUTLET TUBE 56. SHOCK MOUNT
27. WASHER - MS35338-43 57. RIVET
28. NUT - MS35650-302 58. HEATER LEFT BRACKET
29. WASHER- 10910174-1 59. SCREW - MS90727-13
30. U-BOLT - 11619028 60. LEFT CRADLE BRACKET
31. PUMP MOUNTING PLATF 61. MOUNTING CLAMP - MS35842-16
32. STRAP 62. FUEL FILTER
33. PUMP MOUINTING BRACKET 63. RIGHT CRADLE BRACKET
34. CLAMP - MS35842-15 64. SCREW - MS90727-10
65 . CLAMP - 7997714
66. SCREW - MS90728-3
REMOVAL OF SPECIFIC COMPONETS

Item Procedure
No.
NOTE. When component removal involves breaking coolant circuit it is recommended that vehicle coolant
system be drained first.
8 COOLANT HEATER: Shut off fuel supply (valve is located just below adapter, item 43). Disconnect fuel
line (13) at elbow (9). Disconnect wiring harness (7) at heater receptacle. Loosen clamp (11) and
disconnect outlet hose (12). Loosen clamp (11) and disconnect heater inlet hose at coolant pump. Loosen
clamp (50) and disconnect exhaust pipe assembly (1). Remove two mounting clamps (61) and remove
coolant heater.
12-7
C3, TM 9-2350-230-12
Table 12-1. Removal/Installation - Vehicle Winterization Kit Components - Continued
23 FUEL PUMP: Shut off fuel supply (valve is located just below adapter, item 43). Disconnect fuel pump
outlet tube (26) from adapter (24) at fuel pump. Disconnect fuel pump inlet hose (44) from elbow (9).
Disconnect power lead from harness (7) and remove screw (19) and washer 20). Remove two nuts (16)
holding pump to bracket, and remove fuel pump assembly.
36 COOLANT PUMP: Disconnect power lead from harness (7) and disconnect ground lead at fuel pump
bracket. Loosen clamps (11), and disconnect inlet (41) and outlet (45) hoses. Remove two clamps (34
and 35) and remove coolant pump.
42 BATTERY HEATER: Disconnect and remove batteries (figure 9-97). Loosen two clamps (11) and
disconnect inlet (44-1) and outlet (41) hoses. Remove heater tray.
56 SHOCK MOUNTS: Remove coolant heater (item no. 8 above). Remove two screws (2) and washers (47,
47-1) to remove each heater bracket (55 and 58). On right bracket, also remove screw (66), washer (20)
and harness clamp. Remove nuts (51) washers (29, 52) screws (59, 64), exhaust pipe bracket (53, left
bracket only), snubbing washers (54) and ’cradles (60, 63). Drill or punch out rivets (57) to remove shock
mounts.
62 FUEL FILTER: Shut off fuel supply (valve is located just below adapter, item 43). Refer to figure 9-134 for
filter service. OTHER COMPONENTS: Replace unserviceable components as required.
INSTALLATION
Reverse removal procedure.
Whenever coolant lines have been disconnected it is necessary to bleed air from the system as follows:
Disconnect coolant heater outlet hose (12) at elbow (10). Add coolant at surge tank until coolant spills
from both elbow and hose. Reinstall hose on elbow without allowing air to enter either hose or elbow.
Tighten clamp and continue adding coolant until full level is reached in surge tank.
After engine has been run to raise coolant pressure in system make visual check of all hose connections
for leaks.
Figure 12-6. (Added) Winterization kit coolant flow diagram.
12-8
C3, TM 9-2350-230-12
Figure 12-7. (Added) Winterization kit wiring diagram.
Figure 12-8. (Added) Removal/installation - winterization kit control box.
12-9
C3, TM 9-2350-230-12
Figure 12-9. (Added) Repair - winterization kit control box.
12-10
C4, TM 9-2350-230-12
Figure 12-10. (Added) Coolant heater wiring harness
12-11
C4, TM 9-2350-230-12
Figure 12-11. (Added) Disassembly/assembly - winterization kit coolant heater thermostat
12-12
C4, TM 9-2350-230-12
A. COOLANT HEATER INSTALLED B. COOLANT HEATER SWITCH GUARD AND AIR

TUBE REMOVED,.
FLAME DETECTOR SWITCH ASSEMBLY REMOVAL
1. REMOVE 4 SCREWS AND FLAME DETECTOR IGNITER REMOVAL
SWITCH GUARD. 1. REMOVE END PLATE FROM HEATER BY
2. REMOVE 1 NUT, GROUND WIRE AND WASHER, LOOSENING 4 NUTS AND TURNING PLATE
AND REMOVE COMBUSTION AIR TUBE. COUNTERCLOCKWISE.
3. DISCONNECT 5 WIRES FROM FLAME DETECTOR 2. DISCONNECT IGNITER POWER LEAD STRAP.
MICROSWITCH. INSTALL SCREWS IN 3. DISCONNECT IGNITER GROUND WIRE AND
MICROSWITCI TERMINALS. BEND THE WIRE SO IT WILL FIT INSIDE A DEEP
4. USE 1/2" OPEN END WRENCH TO LOOSEN SOCKET.
COMPRESSION NUT UNDER FLAME DETECTOR 4. USE 13/16 DEEP SOCKET TO REMOVE IGNITER.
SWITCH. USE CARE TO AVOID DAMAGE TO IGNITER
5, LIFT SWITCH ASSEMBLY STRAIGHT OUT OF FILAMENT.
BUSHING TO AVOID BENDING TUBE AND
BREAKING CERAMIC ROD. OVERHEAT SWITCH REMOVAL
ADJUSTING FLAME DETECTOR SWITCH 1. REMOVE 4 SCREWS AND FLAME DETECTOR

REFER TO FIGURE 9-137. SWITCH GUARD.
2. DISCONNECT 4 ELECTRICAL LEADS FROM
OVERHEAT SWITCH TERMINALS.
3. REMOVE SCREW AND LOCK WASHER FROM
CENTER OF OVERHEAT SWITCH COVER TO
REMOVE COVER.
4. LIFT SWITCH OFF HEAT EXCHANGER.
INSTALLATION
REVERSE REMOVAL PROCEDURE,
REPLACING UNSERVICEABLE
COMPONENTS AS REQUIRED. CONNECT
WIRING AS SHOWN ON WIRING DIAGRAM,
FIGURE 12-7. WHEN REPLACING FLAME
DETECTOR SWITCH ASSEMBLY, RETURN
OLD SWITCH ASSEMBLY TO SUPPORT
MAINTENANCE FOR REPAIR AND RETURN
TO STOCK.
WE 11953
Figure 12-12. (Added) Removal/installation - Coolant heater igniter, overheat switch, and flame detector switch
12-13
C4. TM 9-2350-230-12
A. AMMUNITION BOX STOWAGE BRACKET ASSY. 11619526 . . D. AMMUNITION BOX STOWAGE BRACKET ASSY. 11619528
1. SCREWS (4) (5306-050-1238) 18. SCREWS (4) (5305-269-3234)

2. WASHERS (4) (5306-050-1238) 19. WASHERS (4) (5310-877-5972)
3. STRAP (2590-918-6190) 20. STRAPS (4) (2590-945-8804)
4. STRAP (2540-874-6727) 21. STRAPS (4) (2540-874-6727)
5. SLIDE(2) (5340-999-4286) 22. SLIDES (8) (5340-999-4286)
E. GRENADE PROJECTOR STOWAGE BRACKET ASSY.11619530

B. AMMUNITION BOX STOWAGE BRACKET ASSY. 11619527 23. SCREWS(4) (5305-068-0510)
6. SCREWS (2) (5305-269-3234) 24. SCREWS (2) 5305-558-4181)
7. WASHERS (2) (5310-877-5972) 25. WASHERS (6) (5310-877-5972)
8. STRAPS (2) (2590-918-6191) 26. STRAPS(2) (2590-945-8799)
9. STRAPS(2) (2540-886-1183) 27. STRAPS (2) (2540-874-6730)
10. SLIDES (4) (5340-999-4286) 28. SLIDES (4) (5340-999-4286)
C. AMMUNITION BOX STOWAGE BRACKET ASSY. 11619529

11. SCREWS (2) (5305-269-3235)
12. WASHERS (2) (5310-877-5972)
13. STRAP (2590-918-6190) REMOVAL/INSTALLATION
14. STRAP (2590-945-8804)
15. STRAP (2540-874-6728) REPLACE UNSERVICEABLE COMPONENTS AS REQUIRED
16. STRAP (2540-874-6730)
17. SLIDES (4) (5340-999-4286)
WE 11952
Figure 12-13. (Added) Ammunition stowage added to vehicles without missile subsystem
12-14
C9, TM 9-2350-230-12
Figure 12-14. Removal - mine protective kit (1 of 2)
12-15
C 10, TM 9-2350-230-12
Figure 12-15. Removal - mine protective kit (2 of 2).
Pages 12-17 and 12-18, including figure 12-16-deleted.
12-16
C6, TM 9-2350-230-12
CHAPTER 13
DESCRIPTION, OPERATION AND MAINTENANCE
OF 7.62MM MACHINE GUN M73El
Section 13-1. DESCRIPTION AND DATA
13-1. General
The M73E1 machine gun is interchangeable with 13-3. Tabulated Data - M73E1 Only
previous model M73 for coaxial application on the M551 Weight of gun ............................................... 31.00 lbs.
vehicle. The redesign results in an increase in the Weight of barrel.............................................. 5.25 lbs.
cyclical rate of fire as reflected in tabulated data below. Length of gun ................................................. 35.00 in.
There is no change in controls, operation, or operator/ Length of barrel .............................................. 22.00 in.
crew maintenance. All material in this manual pertaining Number of grooves .................................................... 4
to 7.62MM machine gun is equally applicable to the M73 Twist, right hand............................... one turn in 12 in.
and M73E1 except where otherwise specified. Height cover closed.......................................... 5.30 in.
Height cover opened ........................................ 6.60 in.
13-2. Description Width ................................................................ 4.40 in.
The 7.62MM machine gun M73E1 (fig. 5-11) is a Feed ................................................... metallic link belt
lightweight, air-cooled, metallic link belt fed weapon. It Operation ................................. Recoil with gas assist
has a short receiver, is recoil operated with a gas assist Cooling .....................................................................Air
to boost recoil, and designed with a quick change barrel Muzzle velocity................................2,800 fps (approx)
with fixed -Headspace. The cycle of operation and Rate of fire (cyclic) .....................500 to 600 rd per min
functioning is initiated from the retracted position of the Maximum range .........................See appropriate F. T.
barrel extension assembly. Major groups and assemblies (approx) (3,700 meters or 4,150 yds)
are illustrated in figure 13-1 and described in table 13-1. Maximum effective range .......................... 900 meters
(tracer burnout point)
Method of target engagement.................. 20-30 round
bursts
Table 13-1. Major Groups and Assemblies - M73E1 (Fig. 13-1)

ASSEMBLY OR GROUP DESCRIPTION
Jacket assembly group (Items 1 through 4) Secured to front portion of the receiver assembly (trunnion block).
Designed for quick removal. Consists of jacket assembly, with bearing lock and barrel
assembly.
Cover assembly (Item 5)

Located on top of the receiver assembly over the feed tray group. Secured to receiver by
the right and left latch rod assemblies. It feeds the belt and positions and holds the
cartridges for chambering. The feed mechanism is actuated by a stud on the barrel
extension, which engages the feed cam.
Feed tray group (Item 6)

Located on top of receiver assembly under the cover assembly. It is composed of the
cartridge stop assembly and the feed tray assembly. The feed tray group serves as a
guide for the belt to assist in positioning the cartridges and provides directional control for
link ejection.
13-1
C6, TM 9-2350-230-12
Table 13-1. Major Groups and Assemblies - M73E1 (Fig. 13-1) - Continued
ASSEMBLY OR GROUP DESCRIPTION

Back plate assembly, (Items 7 through 10)
helical (driving) Helical (driving) springs are located at rear of the barrel extension
springs and guide assembly. They are retained in position by the guide rods, which
rod group are secured to the back plate. They help absorb recoil shock and provide the energy to
feed, strip, chamber, and fire the following round. The back plate assembly is located at
the rear portion of the receiver assembly. It houses the trigger sear and solenoid. The
trigger safety is located at the top of the back plate. It acts as a positive sear block for
manual operation of the trigger and when the weapon is operated by the solenoid. It
contains a nut shield covering the nuts securing solenoid to back plate.
Barrel extension (Items 11 through 13)

group The action group of the weapon. Composed of the breechblock assembly and barrel
extension assembly. This group chambers and fires the cartridge, locks and unlocks the
breech, and extracts and ejects the spent cartridge cases.
Charger group (Items 14 through 17)

Composed of a retaining ring and charger assembly. The retaining ring secures the
charger assembly to the receiver. The charger assembly may be assembled on the right
or left side of the receiver by repositioning the slide connector, buffer pivot pin, and
charger mounting stud. The charger is utilized to manually charge the weapon (before
loading), loading the first round, and to recharge the weapon in case of a malfunction or
stoppage.
Receiver assembly (Item 18)

Serves as a support for all major assemblies and groups. It houses the action of the
weapon and, through a series of cam ways, controls the functioning of the barrel
extension assembly and breechblock assembly.
NOTE
The serial number is located on the left side of the receiver.
Section 13-2. OPERATING INSTRUCTIONS
13-4. Service Upon Receipt of Materiel Refer to 7.62MM coaxial machine gun as well as the 152MM
table 2-1. Refer to figure 5-13 for installation of flash gun/launcher (figure 2-23).
hider
b. Controls. For description, illustration and function of
13-5. Instruments and Controls a. Instruments Ml119 controls refer to table 13-2.
telescope and XM44E1 periscope are used for aiming
the 13-6. Operation
For preparation, loading and firing pro cedures refer to
Chapter 3.
13-2
C6, TM 9-2350-230-12
Figure 13-1. Major groups and assemblies.

13-3
C6, TM 9-2350-230-12
Table 13-2. Controls
CONTROL FUNCTION REFERENCE
Charger assembly Retracts barrel extension assembly Fig. 5-11
Disconnector pull Retains barrel jacket assembly on receiver Fig. 5-11. 1

ring
Manual firing trigger Manually fires weapon Fig. 5-11
Trigger safety Prevents accidental firing of machine gun Fig. 5-11
Cover latch rod Holds cover and feed tray in closed latch position Fig. 5-11. 2
assemblies
Cover latch rod Retains cover on receiver Fig. 5-11. 2

lock
Left- or right-hand Actuates buffer support Fig. 5-12

buffer support
lever
Gun and turret Controls electrical power supply to gun solenoid Fig. 2-19
control selector
Gunner’s power control Controls elevation and traverse, and electrical firing Fig. 2-19
handle
Commander’s power Controls elevation and traverse, and electrical firing Fig. 2-19
control handle
Firing button (on manual Fires gun electrically Fig. 2-19

elevation handwheel)
Section 13-3. MAINTENANCE INSTRUCTIONS
13-7. Cleaning Inspection and Lubrication b. Replacement of Parts. Crew/operator

is authorized to replace the following parts
when unserviceable:
Refer to table 13-3, table 13-4, and LO 9-
2350-230-12 Barrel assembly (fig. 13-1, item 1)
Helical compression springs (driving
13-8. Preventive Maintenance Checks springs) (fig. 13-1, item 9)
and Services
Breechblock assembly (fig. 13-1, item 12)
Barrel extension assembly (fig. 13-1,
Refer to table 4-1 item 11)
13-9. Troubleshooting WARNING: M73 and M73E1 barrel extension

assemblies are not interchangeable. Use only
Refer to table 5-1 assembly (11013360) FSN 1005-937-8256 on
M73. Use only assembly (11013432) FSN 1005-
13-10. Maintenance 832-9612 on M73E1.
a. Disassembly/Assembly. Refer to table If further replacement of parts is required

5-9 notify organizational maintenance.
13-4
C6, TM 9-2350-230-12
Table 13-3. Specific Lubrication Instructions
STEP PROCEDURE
USUAL CONDITIONS 7.62MM MACHINE GUN M73E1

1 Immediately after firing, clean all powder fouled surfaces with (CR) rifle bore cleaning compound.
CAUTION Do not use rifle bore cleaning compound to clean back plate assembly. Use clean
cloths to remove foreign matter. Do not lubricate the back plate assembly due to danger of
contamination of the solenoid.
MAJOR GROUPS AND ASSEMBLIES

2 Disassemble machine gun into its major groups and assemblies, table 5-9.
3 Clean the components with SD, dry cleaning solvent.
4 Wipe dry and oil with PL special, general purpose lubricating oil, above 0° For LAW, weapons lubricating
oil, below 0° F
5 Thereafter, clean and oil as above every 90 days unless inspection reveals shorter intervals are required.
6 Assemble the major groups and assemblies, table 5-9.
7 Remove oil from barrel bore before firing.
APPLICATION OF SEMI-FLUID LUBRICATING OIL (LSA)
Semi-fluid lubricating oil is an all purpose lubricant which may be applied in all temperature ranges. This
lubricant should be applied before the weapon is fired.
8 Disassemble gun into major groups and assemblies, table 5-9. Specific points to be lubricated are:
a. In recesses or grooves wherein the belt feed slide and the feed cam rides in the cover assembly.
b. In breechblock camways and in receiver rail and cartridge rammer grooves of the barrel extension.
On all rollers and roller riding surfaces.
c. On the receiver rails and in the breech closing, hammer cocking, breech opening, and breechblock
roller camming groove areas of the receiver.
NOTE . LSA should be used sparingly. After lubricating, the components will be functioned to allow
the oil to spread.
13-5
C6, TM 9-2350-230-12
Table 13-3. Specific Lubrication Instructions - Continued
STEP PROCEDURE
UNUSUAL CONDITIONS
1 Reduce lubrication intervals to less than-90 days if inspection indicates rust or corrosion.
NOTE Lubrication intervals may be shortened during inactive periods.
2 Changing grade of lubricants:
a. Lubricants are prescribed in accordance with temperature ranges: above zero and below zero.
b. When to change grade of lubricants is determined by maintaining a close check on the operation
of the weapon during the approach to change over periods in accordance with weather forecast
data.
3 Extreme cold weather lubrication is contained in TM 9-207.
NOTE Make certain all parts are dry and free from condensation, then lubricate.
4 Extreme hot weather or humid salt-air conditions require more frequent servicing since these conditions
tend to dissipate the lubricants.
5 Lubricated surfaces are to be inspected and cleaned of fouled lubricants under sandy o0 dusty conditions.
6 After immersion, or as soon as tactical situation permits, accomplish steps 2 through 6, under usual
conditions.
13-6
C6, TM9-2350-230-12
Table 13-4. Cleaning and Inspection of 7.62MM Machine Gun M73E1
COMPONENTS CLEANING AND INSPECTION

CLEANING
NOTE. General cleaning procedures, refer to TM 9-208-1, and TM 9-247.
Barrel Assembly Remove foreign matter with CR, rifle bore cleaning compound, applied
Bore to cleaning patches and attached to small arms cleaning rod swab
holder section 7266110 (3, fig. B-6). Use small arms cleaning bore
brush 5564174 (8, fig. B-6) attached to small arms cleaning rod
section 7266109 (2, fig. B-6) to clean any remaining foreign matter.
Cleaning patches are used to wipe the bore clean.
Chamber Insert small arms cleaning chamber brush 7790452 (7, fig. B-6) into the
chamber and apply a counterclockwise motion to clean the barrel
assembly chamber. CR, rifle bore cleaning compound, may be
used, if necessary.
Back Plate Assem- Use only clean cloth to remove dirt.
bly with Solenoid
Receiver Assembly Clean the inside with small arms cleaning receiver brush 7790342 (5,
fig. B-6) and CR, rifle bore cleaning compound. Wipe dry and
apply a light coat of oil.
INSPECTION
Jacket Assembly
with Bearing
Group
Jacket Assembly Check mounting block for rough spots and cracks. Inspect all parts for
with Bearing rust, corrosion, and foreign matter. Inspect bearing lock for
staking and bearing for damaged flash hider threads.
Barrel Assembly Check for bulges, cracks, and rust.
NOTE. A gap between the Stellite liner and the gun tube is allowed
at manufacture to permit heat expansion. This ring approximately
eight inches from rear end of barrel assembly does not reflect a ringed
or bulged bore.
Cover Assembly Check feed cam for cracks and wear. Check spring action of depressor
and stripper. Check feed slide assembly and feed slide track
assembly for wear or damage. Assure that all pawls, under spring
tension, function properly. Check cover and track assemblies for
wear and damage.
Feed Tray Group Make certain the cartridge stop assembly is secure to the feed tray
assembly. Check tray for proper fit on receiver assembly.
Guide Rod Assembly Check guide rod assemblies for straightness. Check compression
and Compression helical spring for cracks and kinks.
Helical Spring
(Driving Spring)
13-7
C6, TM 9-2350-230-12
Table 13-4. Cleaning and Inspection of 7.62MM Machine Gun M73E1 - Continued
COMPONENTS CLEANING AND INSPECTION

Back Plate Assem- Check spring action of solenoid trigger and sear of back plate assembly
bly with Solenoid with solenoid. Check trigger safety for proper functioning.
Breechblock Check for freedom of movement of the roller. Check the spring action
Assembly of the firing pin and make certain the firing pin will protrude from
the breechblock.
Barrel Extension Check rammer assembly. Make certain there is spring action in the
Assembly cartridge extractor and firing pin extension. Make certain that
hammer sear housing is tightly secured to the barrel extension.
Check spring action of the hammer sear. Check lower assembly
for freedom of action of rollers. Check action of hammer for
proper functioning.
Charger Assembly Check for loose parts. Pull on charger handle and check spring action.
Receiver Assembly Check spring action of the right and left cover latch rod assemblies.
Check the spring action of the buffer support lever assemblies by
operating either lever. Examine camways of receiver body for
cracks and wear. Make certain rate control slide retaining
screws are tight and staked.
Section 13-4. AMMUNITION

13-11. General with 7.62MM machine gun M73 or M37E:,
Refer to SC 1305/30 IL for ammunition used
Section 13-5. SHIPMENT AND LIMITED STOWAGE
AND DEMOLITION TO PREVENT ENEMY USE
13-12. General (Refer to Chapter 6.)
13-8
TM 9-2350-230-12
APPENDIX I
REFERENCES
A-1. PUBLICATION REFERENCES
OPERATOR/CREW
AR 385-40 .....................Safety: Accident Report and Records

AR 385-63 .....................Safety: Regulations for Firing Ammunition for Training, Target Practice, and Combat
AR 700-1300-8 ..............Logistics (General) Malfunctions Involving Ammunition and Explosives
DA Form 285 .................Accident Report
DA Form 348 ................Driver Qualification Record
DA Form 461-5 ..............Limited Technical Inspection
DA Form 2028 ...............Recommended Changes to DA Technical Publications
DA Form 2415 ...............Ammunition Condition Report
SC 1305/30-IL ...............Ammunition, through 30mm
SF Form 91 ...................Operator’s Report of Motor Vehicle Accident
TB 9-380-101 ................Security Classification of Missile and Large Rocket Systems and Components
-0°
TM 9-207 .......................Operation and Maintenance of Ordnance Materiel in Extreme Cold Weather to -65o
TM 9-208-1 ....................Cleaning of Ordnance Materiel
TM 9-208-2 ....................Cleaning, Drying, and Abrading Equipment for Cleaning Ordnance Materiel
TM 9-1300-206 ..............Care, Handling, Preservation and Destruction of Ammunition
TM 9-2350-230-ESC .....Equipment Serviceability Criteria (ESC) for Armored Reconnaissance Airborne Assault Vehicle,
FT., 152MM Gun-Launcher, XM551
TM 11-5820-401-10.......Radio Sets AN/VRC-12 and AN/VRC-43, -44, -45, -46, -47, -48, and -49
TM 11-5820-498-10.......Operator’s Manual: Radio Sets AN/VRC-53 and AN/GRC-125 and Amplifier-Power Supply Group
OA-3633/GRC
TM 21-301 .....................Driver Selection, Training, and Supervision, Half-Tracked and Full Tracked Vehicles
TM 21-306 .....................Manual for Full-Tracked Vehicle Driver
TM 38-750 .....................The Army Equipment Record Procedures
A-1
C6, TM 9-2350-230-12
A-1. PUBLICATION REFERENCES - CONTNUED
ORGANIZATIONAL MAlNTENANCE
DD Form 6 .....................Report of Damaged or Improper Shipment

DD Form 1397 ...............Processing and Deprocessing Record for Shipment, Storage and Issue of Vehicles and Spare
Engines
FM 5-20B.......................Camouflage Basic Principles
TB 9-299/1.....................Processing of Unboxed Self-Propelled and Towed Class II Ordnance General Supplies and
Related Materiel
TB 9-1300-246/1 ...........Identification of Ammunition Employing New Color Coding Standards
TB 746-93-1 ..................Color and Markings of Military Vehicles, Construction Equipment and Materials Handling
Equipment
TM 750-116 ...................Organizational Maintenance Procedures for Purging and Charging of Fire Control Instruments.
TB ORD 548 ..................All Combat Vehicles: Failure of Azimuth Indicators, Sighting and Fire Control Instruments
TB ORD 651 ..................Use of Antifreeze Solution in Engine Cooling Systems
TM 3-4240-236-20P ......Organizational Maintenance Repair Parts and Special Tool Lists: Filter Unit Gas Particulate, Tank,
12CFM, M8A3
TM 9-213 .......................Painting Instructions
TM 9-1005-213-25.........Organizational, DS, GS, and Depot Maintenance Manual Including Repair Parts and Special Tools
Lists: Machine Gun, Caliber. 50; Browning M2, Heavy Barrel, Flexible.
TM 9-1005-233-25.........Organizational, DS, GS, and Depot Maintenance Manual Including Repair Parts and Special Tool
Lists: Machine Gun, 7. 62MM, M73.
TM 9-2350-230-25P/1 ...Organizational, Direct and General Support and Depot Maintenance Repair Parts and Special
Tool List for Armored Reconnaissance Airborne Assault Vehicle: FT., 152MM Gun-Launcher,
M551-Hull Suspension and Miscellaneous Components
TM 9-2350-230-25P/2 ...Organizational, Direct and General Support and Depot Maintenance Repair Parts and Special
Tool List for Armored Reconnaissance Airborne Assault Vehicle: FT., 152MM Gun-Launcher,
M551-Turret Elevating and Traversing Systems, Cupola, Gun-Launcher, Small Arms and Fire
Control
TM 9-6140-200-15.........Operation and Organizational, Field and Depot Maintenance, Storage Batteries, Lead-Acid Type
TM 11-5820-401-20.......Organizational Maintenance Manual: Radio Sets AN/VRC-12, -43, -44, -45, -46, -47, -48, and-49
TM 11-5820-401-20P ....Organizational Maintenance Repair Parts and Special Tool Lists: Radio Sets AN/VRC-12, -43, -
44, -45, -46, -47, -48 and -49
TM 11-5820-498-20.......Organizational Maintenance Manual: Radio Sets AN/VRC-53, AN/GRC-125 and Amplifier - Power
Supply Group OA-3633/GRC
A-2
C6, TM 9-2350-230-12
APPENDIX II. BASIC ISSUE ITEMS LIST

Section B-1. INTRODUCTION
B-1. Scope assemblies at DSU and GSU level. These

assemblies will not be stocked above DS and
This appendix lists items which accompany the GS level or returned to depot supply level.
Armored Reconnaissance/Airborne Assault Vehicle
(AR/AAV) M551 or are required for installation, M Repair parts which are not procured or stocked,
operation, or operator’s maintenance. but are to be manufactured indicated
maintenance levels.
B-2. General
P Repair parts which are stocked in or supplied
This Basic Issue Items List is divided into the from the GSA/DSA or Army supply system, and
following sections: a. Basic Issue Items Section B-2. A authorized for use at indicated maintenance
list of items which accompany the AR/AAV M551 are categories.
required by the crew/operator for installation, operation,
or maintenance. P2 Repair parts which are procured and stocked for
insurance purposes because the combat or
b. Maintenance a Operating Supplies Section B-3.. A military essentially of the end item dictates that a
listing of maintenance and operating supplies required minimum quantity be available in the supply
for initial operation. system.
B-3. Explanation of Columns X Parts and assemblies which are not procured or
stocked and the mortality of which normally is
The following provides an explanation of columns in the below that of the applicable end item or
tabular list of Basic Issue Items, Section B-2. component. The failure of such part or assembly
should result in retirement of the end item from
a. Source, Maintenance. and Recoverability Codes the supply system.
.(SMR)
X1 Repair parts which are not procured or stocked.
(1) Source code. Indicates the selection status or The requirement for such items will be filled by
source for the listed item. Source codes are use of the next higher assembly or component.
Code Explanation X2 Repair parts which are not stocked. The

indicated maintenance category requiring such
A Assemblies which are not procured or stocked repair parts will attempt to obtain same through
as such, but are made up of two or more units. cannibalization. Where such repair parts are not
Such component units carry individual stock obtainable through cannibalization, requirements
numbers and descriptions, are procured and will be requisitioned, with accompanying
stocked separately, and can be assembled to justification, through normal supply channels.
form the required assembly at indicated
maintenance categories. (2) Maintenance code, indicates the lowest category
of maintenance authorized to install the listed
G Major assemblies which are procured with item. The maintenance level code is:
PEMA funds for initial issue only as exchange
B-1
C6, TM 9-2350-230-12
Code Explanation of the nomenclature, indicates the Federal stock J

number includes all armament, equipment, accessories,
C Crew/operator and repair parts issued with the item. A part number or
other reference number is followed by the applicable five-
(3) Recoverability code indicates whether digit Federal supply code for manufacturers in
unserviceable items should be returned for parentheses.
recovery or salvage. Items not coded are
expendable. Recoverability codes are: d. Unit of Measure (U/M), Column 4. A 2 character
alphabetic abbreviation indicating the amount or quantity
Code Explanation of the item upon which the allowances are based, e.g., ft,
ea, pr, etc.
R Applies to repair parts (assemblies and
components) which are considered economically e. Quantity Incorporated in Unit, Column 5. This
reparable at direct and general support column indicates the quantity of the item used in the
maintenance levels. When the maintenance functional group. A "V" appearing in this column in lieu of
capability to repair these items does not exist, a quantity indicates that a definite quantity cannot be
they are normally disposed of at the GS level. indicated (e.g., shims, spacers, etc.).
When supply considerations dictate, some of
these repair parts may be listed by the pertinent f. Quantity Furnished with Equipment, Column 6.
NICP for automatic return to supply for depot This column indicates the quantity of an item furnished
level repair as set forth in AR 710-50. When so with the equipment.
listed, they will be replaced by supply on an
exchange basis. g. Illustration, Column 7. This column is divided as
follows:
S Repair parts and assemblies which are
economically reparable at DSU and GSU (1) Figure Number, Column 7a. Indi cates the figure
activities and are normally furnished by supply number of the illustration in which the item is
on an exchange basis. When determined to be shown.
uneconomically reparable by DSU and GSU
activities, they will be returned to depot for (2) Item Number, Column 7b. Indicates the callout
evaluation and analysis prior to final disposition. number used to reference the item in the
illustration.
T High dollar value recoverable repair parts which
are subject to special handling and are issued on B-4. Explanation of Columns in the Tabular List of
an exchange basis. Such repair parts are Maintenance and Operating Supplies Section B-3
normally repaired or overhauled at depot
maintenance activities. a. Component Application, Column 1. This column
identifies the component application of each
U Repair parts specifically selected for salvage by maintenance or operating supply item.
reclamation units because of precious metal
content, critical materials, or high dollar value b. Federal Stock Number, Column 2. This column
reusable casings or castings. indicates the Federal stock number assigned to the item
and will be used for requisitioning purposes.
b. Federal Stock Number, Column 2. This column
indicates the Federal stock number assigned to c. Description, Column 3. This column indicates the
the item and will be used for requisitioning item name and brief description.
purposes.
d. Quantity Required for Initial Operation, Column 4.
c. Description, Column 3. This column indicates the This column indicates the quantity of each maintenance
Federal item name and any additional description of the or operating supply item required for initial operation of
item required. T abbreviation ’w/e", when used as a part the equipment.
B-2
C 10, TM 9-2350-230-12
e. Quantity Required for 8 Hours Operation, Column Periscope, Tank: 1240-788-5463

5. This column indicates the estimated quantities XM44 (early vehicle)
required for an average 8 hours of operation.
Periscope, Tank: 1240-933-5630
f. Notes, Column 6. This column indicates XM44E1 (late vehicle)
informative notes keyed to data appearing in a preceding
column. Telescope, Articulated: 1240-762-9333
M119
B-5. Special Information or
Telescope, Articulated: 1240-437-1254
a. Items listed below are components of the XM127
major combination.
Mount, Telescope: 1240-762-9334
Component FSN M149
or
Machine Gun, Cal 50: 1005-726-5636 Mount, Telescope: 1240-178-8440
M2, HB, flex M165
Machine Gun, 7.62-MM: 1005-869-8816
M73 (coaxial) b. Identification of the usable on codes included in
or column 3 of this publication are:
Machine Gun, 7.62-MM: 1005-937-7327
M219 (M73E1) Code Used On
Mount Assembly, Machine 1005-704-6650 A Caliber . 50 Machine Gun, M2
Gun: cal 50 B 7, 62MM Machine Gun, M73
Periscope, Tank: infrared 6650-762-9336 C 7. 62MM Machine Gun, M219 (M73E1)
M48 (driver’s)
Consisting of: B-6. Abbreviations
1-Body (in driver’s See MIL-STD-12.
compartment stowage box)
1-Head (in driver’s B-7. Federal Supply Code for Manufacturers
compartment stowage box)
1-Headrest Assembly, 6650-907-9679 Code Manufacturer
Optical Instrument: (in
periscope stowage box 10001 Naval Ordnance Systems Co.
cover) 19200 Frankford Arsenal
Periscope: 6650-856-9455 19204 Rock Island Arsenal
M37 (loader’s) 19205 Springfield Armory
Periscope, Tank: 6650-788-5464 19206 Watervliet Arsenal
M47 19207 Army Tank-Automotive Command
Quadrant, Fire Control, 1290-891-9999 80244 General Services Administration
Gunner’s: Federal Supply Service
M1Al w/case 81348 Federal Specifications
Quadrant, Fire Control: 1290-078-5568 81349 Military Specifications
elevation, M13A1C 89372 North American Aviation Inc.
89875 Defense Supply Agency Directorate of
Medical Materiel Defense Per-
sonnel Support Center
96906 Military Standard
99974 AC Electronics Div. of General Motors
Corporation
B-3
C8. TM 9-2350-230-12
Section B-2. BASIC ISSUE ITEMS LIST
(1) (2) (3) (4) (5) (6) (7)

Description Unit Qty Qty Illustration
of inc furn (A) (B )
SMR Federal Stock Ref no. & mfr Usable Meas in with Fig Item
Code Number Code on code Unit equip no. No.
GROUP 06 ELECTRICAL SYSTEM

0609 LIGHTS AND LAMPS
PC 6240-155-7836 LAMP, INCANDESCENT: 28v, .04 amp, no. 327 (In bulb ea 27 6
box) (See tables 5-3 and 5-6)
MS25237-327
box) (See table 5-6)
MS15570-623 (96906)
PC 6240-950-1727 LAMP: 28v, .08 amp, no. 757 (In bulb box) (S table 5-3) ea 1 1
PC 6240-019-0877 LAMP: 28v, .23 amp, no. 1251 (In bulb bx) (Stable 5-3) ea 3 3
MS15570-1251 (96906)
PC 6240-044-6914 LAMP, INCANDESCENT: 28v, 1.02 amp, no. 1683 (In ea 1 1
bulb bx) (See table 5-3)
MS35478-1683
box) (See tables 5-3 and 5-6)
MS35478-1691 (96906)
PC 6240-155-7967 LAMP: 14. 4v, . 10 amp, no. 1813 (In bulb bx) (See ea 1 1
table 5-3)
8599150-004 (99974)
GROUP 15 FRAME TOWING ATTACHMENTS

AND DRAWBARS
1503 TOWING ATTACHMENTS

2540-767-3149 CABLE ASSEMBLY: Steel, towing 3/4" x 10 ft (On hull ea 1 1
exterior, rear)
10861718 (19207)
2540-776-0103 PINTLE ASSEMBLY: (Turret, exterior left) ea 1 1
MS51118-1 (96906)
WASHER: Pintle mounting (Functional location) ea 1 1
10910174-14
GROUP 18 BODY, CAB, HOOD AND HULL
1808 STOWAGE BOXES

2540-808-6858 BOX ASSEMBLY: Spar lamp stowage (In oddment box) ea 1 1 B-1 1
11594202 (19207)
GROUP 22 BODY, CHASSIS OR HULL,

AND ACCESSORY ITEMS
2201 CANVAS, RUBBER OR PLASTIC ITEMS

2540-670-2459 BAG ASSEMBLY: Pamphlet (In driver’s compartment) ea 1 B-1 2
7961712 (19207)
8465-705-2438 CASE: Ammunition (1-at loader’s station, 1-n driver’s ea 2 B-1 3
compartment)
MIL-C-43312 (81349)
2540-587-2532 TARPAULIN: Nylon 12 x 17 ft. (On turret exterior rack) ea 1
10936264 (19207)
B-4
C6, TM 9-2350-230-12
(1) (2) (3) (4) (5) (6) (7)

2202 ACCESSORY ITEMS

7240-242-6153 CAN, WATER: 5 gal. std. (On turret exterior) ea 1
64C 281 (80244)
8345-178-8437 CASE: Flag CS-90 5-C-40 ea 1 B-1 4
MIL-F-40045 (81349)
8345-227-1511 FLAG: MC-273 (Red) ea B-1 5
MIL-F-40045 (81349)
8345-227-1405 FLAG: MC-274 (Yellow) ea 1 B-1 6
MIL-F-40045 (81349)
8345-227-1406 FLAG: MC-275 (Green) ea 1 B-1 7
MIL-F-40045 (81349)
8345-242-3650 STAFF: Flag ea 3 B-1 8
MIL-F-40045 (81349)
6230-264-8261 FLASHLIGHT: MX-991/U 6Z-4007-991 (1-n turret ea 2
oddment box, 1-n driver’s compartment)
MIL-F-3747 (81349)
6545-922-1200 KIT, FIRST AID: Motor vehicle, 12 unit size 1 ea 1 B-1 11
(At turret commander’s station)
9-221-220 (89875)
8415-266-8843 MITTENS, ASBESTOS: M1942 (At loader’s station) pr 1
MIL-M-11199 (81349)
5340-912-4086 PADLOCK SET: 1-3/4" W/Clevis consisting of 1 lock, ea 1
2 keys (In tool bag)
MS21313-160 (96906)
8135-663-0196 TAPE, PRESSURE SENSITIVE ADHEXIVE: waterproof ea 1
(Roll) 3" ID core, 2" width, 60 yard roll
PPP-T-60 (81348)
GROUP 26 TOOLS AND TEST EQUIPMENT

2600 COMMON TOOLS
5140-473-6256 BAG, TOOL, (EMPTY) SATCHEL: driver’s compt. ea 1

MIL-B-43533 (81349)
Th following items are carried in tool bag
5120-526-6044 BAR, Pinch, 9/16" x 11-7/8" Long ea 1
5266044 (19204)
8020-297-6657 BRUSH, PAINT, Sash Oval (Parts Cleaning) ea 2
1-7/16" wide, 1-1/16" thick, 2-3/4" Iong.
MS16866 (96906)
5110-236-3272 CHISEL, Cold Hand, 3/4" x 6-1/2" long ea 1
GGG-C-313 (81348)
4930-288-1511 EXTENSION, Lube, Gun, Hyd, , 12" long ea 1
MIL-L-4387 (81349)
5120-240-8705 EXTENSION, Socket Wrench, 1/2" sq. dr. 20" long ea 1
MS16243-11 (96906)
B-5
C6, TM 9-2350-230-12
(1) (2) (3) (4) (5) (6) (7)

2600 COMMON TOOLS - Continued
4930-253-2478 GUN, Grease ea 1

MIL-G-3859 (81349)
5120-224-4047 HAMMER, Mach., Ball Peen, 2 lbs., Type II, ea 1
Class 1, Style A
GGG-H-86 (81348)
5120-236-7590 HANDLE, Socket Wrench, Hinged, 1/2" sq. dr., ea 1
18" long
MS16245-3 (96906)
5120-230-6385 HANDLE, Socket Wrench, Ratchet, 1/2" sq. dr., ea 1
9-1/2" long
MIL-W-15838 (81349)
5120-198-5409 KEY, SOCKET HEAD SCREW: 5/16" Hex., 6-3/32" ea 1
long (Nominal 6")
GGG-K-275 (81348)
5120-240-5292’ KEY, SOCKET HEAD SCREW: 1/8" Hex., 3-27/32" ea 1
long (Nominal 3-3/4")
GGG-K-275 (81348)
5120-223-7397 PLIERS, Comb., Slip Joint, W/Cutter 8" long ea 1
MS15382-1 (96906)
5120-809-1570 SCREWDRIVER, Flat Tip, 18" Blade, 21-5/8" O/A ea 1
MS15218-14 (96906)
5120-198-5410 KEY, SOCKET HEAD SCREW: 3/16" Hex., 4-19/32" ea 1
long, (Nominal 4-1/2" long)
GGG-K-275 (81348)
5120-260-4837 SCREWDRIVER, Flat Tip, 8" Blade 11-1/2" O/A ea 1
MS15218-9 (96906)
5120-224-7375 SCREWDRIVER, Cross Tip, Phillips, Tip Size No. 4, ea 1
6" Blade
GGG-S-121 (81348)
5130-714-0593 SOCKET, Socket Wrench, 1/2" sq. dr., 6 pt., ea 1
7/16" opening
MS16581-11 (96906)
1/2" opening
M816254-22 (96906)
9/16 opening
MS16254-23 (96906)
5/8" opening
MS16254-25 (96906)
11/16" opening
MS16254-26 (96906)
5120-189-7985 SQCKET. Socket Wrench, 1/2" sq. dr., 12pt., ea 1
3/4" openings
M81624-27(96906)
B-6
C6, TM 9-2350-230-12
(1) (2) (3) (4) (5) (6) (7)

2600 COMMON TOOI00- Continued

13/16" opening
MS16254-29 (96906)
5120-189-7935 SOCKET, Socket Wrench 1/2" sq. dr., 12 pt., ea 1
15/16" opening
MS16254-31 (96906)
1-1/8" opening
MS16254-34 (96906)
5120-269-7971 UNIVERSAL JOINT, Socket Wrench, Hand, 1" sq. dr ea 1
MS16257-3 (96906)
5120-240-5328 WRENCH, Adj., Single End, 15/16" opening, 8" long ea 1
MS15461-3 (96906)
5120-224-3102 WRENCH, Open End, Fixed, Double Head Type, 5/8" ea 1
and 3/4" openings
MS16380-11 (96906)
and 9/16" openings
MS16380-6 (96906)
and 15/16" openings
MS16380-17 (96906)
5120-187-7133 WRENCH, Open End, Fixed Double Head Type, 1" ea 1
and 1-1/8" openings
MS16380-20 (96906)
and 7/16" openings
MS16380-4 (96906)
5120-227-7387 WRENCH, Socket, Hand, Single Socket T-Type, ea 1
3/4" Hex, 6-1/2" O/A
MS16260-5 (96906)
5120-293-0139 WRENCH, Socket, Hand, Single Socket T-Type, ea 1
15/16" Hex, 7-3/4" O/A
MS16260-8 (96906)
2600 PIONEER TOOLS
5110-293-2336 AX: Chopping, Single Bit, 4 lbs., hull exterior rear ea 1 B-2 1
GGG-A-926 (81348)
5120-240-6040 CROWBAR: Pinch point, nor. dia. 1", 47" to 49" long, ea 1 B-2 2
hull exterior rear
GGG-B-101 (81348)
MATTOCK: Pick with Handle, 5 lbs. Hull exterior rear B-2 3
Consisting of:
5120-243-2395 MATTOCK ea 1
GGG-H-506 (81348)
5120-288-6574 HANDLE, MATTOCK-PICK ea 1
NN-H-93 (81348)
5120-293-3336 SHOVEL: General Purpose, D-Handle, Round Point, size 2 ea 1 B-2 4
GGG-S-326 (81348)
B-7
C9, TM 9-2350-230-12
(1) (2) (3) (4) (5) (6) (7)

2602 PUBLICATIONS
7510-889-3494 BINDER, EQUIPMENT LOG BOOK: (In pamphlet bag) ea 1

MIL-B-43064 (81349)
EQUIPMENT LOG BOOK: Order per ea 1
TM 38-750 (In binder)
L09-2350-230-12 LUBRICATION ORDER: (In pamphlet bag) ea 1
TM9-2350-230- MANUAL, EQUIPMENT SERVICEABILITY CRITERIA: ea 1
ESC (In equipment log book binder)
TM9-2350-230- MANUAL, OPERATOR’S AND ORGANIZATIONAL ea 1
12 MAINTENANCE: (In pamphlet bag)
FT-152-A-1 CANNON, 152MM GUN-LAUNCHER: M81El and M81 on

15 July 70 Armored Reconnaissance/Airborne Assault Vehicle:
152MM, M551, Firing Cartridge, 152MM: HEAT-MP-T,
XM409E5; Cartridge, 152MM: TP-T, XM411E3; Cart-
ridge, 152MM: HE-T, XM657E2; Cartridge, 152MM:
152MM: Cannister, XM625.
2604 SPECIAL TOOLS
5140-261-4994 CARRIER: Wire cutter (In tool bag) ea 1 B-2 8

MIL-C-729 (81349)
5110-595-8229 CUTTER, WIRE: (In carrier in tool bag) ea 1 B-2 7
MIL-C-386 (81349)
4910-906-1053 FIXTURE ASSEMBLY, TRACK: (Hull rear battery access ea 1 5-5
door)
10955739 (19207)
5120-449-7042 HANDLE: Steel tubular, 24" long, 7/8"’ ID. (Hull rear ea 1 B-2 6
battery access door, strapped w/track fixture)
GGG-W-636, Type 19, Class 1 (81348)
5120-678-2795 PUNCH ASSEMBLY: Drift pin (In tool bag) ea 1 5-5
11861180 (19207)
5120-288-9681 WRENCH: Box Socket, Stub End 1-1/8" opening (In tool ea 1 B-2 5
bag)
GGG-W-636, Type 18, Class 1, (81348)
B-8
C9, TM 9-2350-230-12
(1) (2) (3) (4) (5) (6) (7)

GROUP 34 - ARMAMENT AND FIRE CONTROL
3401 PRIMARY ARMAMENT: TOOLS AND EQUIPMENT

FOR 152MM GUN/LAUNCHER M81, M81 MOD, AND M81E1
NOTE. M81 Mod is modified for CBSS.

PC 4933-435-7736 ACTUATOR, ELECTRO-MECHANICAL LINEAR: Firing ea 1 4-4
pulse
11643755 (19207)
P C R 1025-918-5476 BRUSH,BORE ASSEMBLY: Bore and groove (In cover on ea 1 B-3 1
hull battery access door) (M81 and M81 Mod. )
8769852 (19206)
PC 1025-112-8552 BRUSH, BORE ASSEMBLY: (M81E1 Gun-Launcher only) ea B-3 1
11578061 (19206)
PC 2540-134-4754 COVER ASSEMBLY: Ammo protective (In hull ammo rack) ea 34 3-3
11652963 (19206)
PC 1025-918-5474 COVER, ASSEMBLY: Bore brush for M81andM81Mod ea 1 B-3 2
gun-launcher (On hull battery access door)
8769816 (192065
PC 4933-852-6310 BORESIGHT ASSEMBLY: ea 1 B-3 3,4
11577285 (19206)
(B-8.2 Blank) B-8.1

C9, TM 9-2350-230-12
(1) (2) (3) (4) (5) (6) (7)

SMR Federal Stock Ref no. & mfr. Usable Meas in with Fig Item
3401 PRIMARY ARMAMENT: TOOLS AND EQUIPMENT

FOR 152MM GUN/LAUNCHER M81, M81 MOD.,
AND M81E1 - Continued
PC 1025-435-7733 COVER ASSEMBLY:’Bore brush for M81E1 gun-launcher ea 1 B-3 2
(On hull battery access door)
11578227 (19206)
PC 5120-287-2130 - SCREWDRIVER: Offset, 4-1/2"lg. 5/16" wide ,hexagonal ea 1 5-10.1
(In tool bag)
PC 1025-918-8129 PLUG, MUZZLE: (On gun/launcher) ea 1 B-3 7
8769799 (19206)
PC 1025-918-8130 RAMMER, ARTILLERY: (On hull battery access door) ea 1 B-3 8
8769846 (19206)
PC 1090-563-7232 STAFF, SECTION, CLEANING ARTILLERY: M15 (On ea 3 B-3 9
hull rear exterior)
7309228 (19206)
PC 5350-242-4404 STEEL WOOL: (To clean firing probe) (In tool bag) lb 1
11577277 (19206)
PC 9525-063-1444 WIRE, STEEL, CORROSION RESISTING: (In tool bag) ft 1
MS9226-05 (96906)
3402 SECONDARY ARMAMENT
PC 5306-051-4078 BOLT: Machine (To attach spent brass ejection ea 2 2 3-14

chute) (Functional location)
MS90727-36 (96906)
PC 1025-844-3560 CLAMP: Spent brass ejection chute (Functional ea 1 1 3-14
location)
11593536 (19207)
PC 1025-844-3488 CHUTE: Spent brass ejection (Functional location) ea 1 1 3-14
11593535 (19207)
PC 5310-194-0636 WASHER: Flat (to attach chute) (Functional ea 2 2 3-14
location)
MS9320-11 (96906)
REPAIR PARTS FOR CAL 50 MACHINE GUN
PC 1005-726-6131 BARREL: Spare, Cal 50 M2 HB (On turret exterior A ea 1 1 B-7

rack)
7266131 (19205)
PC 1005-614-7463 BOLT ASSEMBLY: Alternate feed (In spare parts box) A ea 1 1 B-4 12
6147463 (19204)
PC 1005-600-8976 EXTENSION ASSEMBLY: Firing pin (On alt. feed bolt) A ea 1 1 B-4 10
6008976 (19204)
PC 1005-600-8959 EXTRACTOR: Small arms cartridge (On alt. Feed A ea 1 1 B-4 1
bolt)
6008959 (19204)
B-9
C6, TM 9-2350-230-12
(1) (2) (3) (4) (5) (6) (7)

REPAIR PARTS FOR CAL 50 MACHINE GUN-Continued

PC 1005-600-9718 LEVER, COCKING: (On alt. feed bolt)A ea 1 1 B-4 4
6009718 (19204)
PC 1005-716-1300 LOCK, ACCELERATOR STOP: (On alt. feed bolt)A ea 1 1 B-4 5
7161300 (19205)
PC 1005-731-2078 PIN, COCKING LEVER: (On alt. feed bolt) A ea 1 1 B-4 3
7312078 (19205)
PC 1005-731-0080 PIN, FIRING: (On alt. feed bolt)A ea 1 1 B-4 11
7310080 (19204)
PC 1005-550-4067 SEAR: (On alt. feed bolt)A ea 1 1 B-4 8
5504067 (19204)
PC 1005-535-1220 SLIDE, SEAR: (On alt. feed bolt) A ea 1 1 B-4 7
5351220 (19204)
PC 1005-209-8720 SPRING, SEAR: Helical compression (On alt. Feed A ea 1 1 B-4 9
bolt)
5009524(19204)
PC 1005-716-1301 STOP, ACCELERATOR: (On alt. feed bolt) A ea 1 1 B-4 6
7161301 (19205)
PC 1005-550-4062 SWITCH, BOLT: Alternate feed (On alt. Feed A ea 1 1 B-4 2
bolt)
5504062 (19204)
TOOLS AND EQUIPMENT FOR CAL 50 MACHINE GUN
1005-714-8550 BOX, SPARE PARTS: (Empty) (In turret oddment A ea 1 B-5 1

box)
7148550 (19204)
1025-844-2716 BRACKET ASSY: Mounting, Weapon Sight (On A ea 1 2-29
cal 50 machine gun or stowage bracket)
11619652 (19207)
1005-508-2589 BRUSH, CLEANING, SMALL ARMS: Chamber (In case A ea 1 B-5 11
8407954 (19204)
1005-550-4037 BRUSH, CLEANING, SMALL ARMS: M4,Bore (In A ea 4 B-5 8
case)
5504037 (19204)
1005-716-2702 BRUSH, CLEANING, SMALL ARMS: Firing Pin A ea 1 B-5 5
Hole (n case)
7162702 (19205)
8105-921-5821 CASE, SMALL ARMS, ACCESSORIES: (In A ea 1 B-5 2
turret oddment box)
11686430 (19204)
1005-714-6365 COUPLER DISCONNECTOR: Cal 50 M20 A ea 1
7146365 (19204)
B-10
C6, TM 9-2350-230-12
(1) (2) (3) (4) (5) (6) (7)

TOOLS AND EQUIPMENT FOR CAL 50 MACHINE GUN -

Continued
1005-735-7116 COVER, MACHINE GUN: (On cal.-.50 machine gun) A ea 1
7357116 (19207)
1005-796-4436 COVER, SPARE BARREL: (On spare barrel) A ea 1 B-5 7
7964436 (19207)
4933-716-0041 EXTRACTOR, RUPTURED CARTRIDGE CASE: A ea 1 B-5 10
(In case)
7160041 (19204)
4933-535-1217 GAGE, HEADSPACE AND TIMING: (In case) A ea 1 B-5 9
53511217 (19207),
1005-716-2072 FLASH, HIDER: (On cal 50 machine gun) A ea 1 3-13
7162072 (19204)
1005-556-4102 ROD, CLEANING, SMALL ARMS: M4 (In case) A ea 1 B-5 4
5564102 (19204)
1005-653-5441 ROD, CLEANING, SMALL ARMS: M7 jointed A ea 1 B-5 3
(In case)
6535441 (19204)
1005-716-2704 SWAB, HOLDER SECTION: Small arms cleaning A ea 1 B-5 6
rod (In case)
7162704 (19205)
7. 62MM MACHINE GUN
P C 1025-134-3051 EXTENSION ASSEMBLY, SPENT BRASS BC ea 1 1 3-7

EJECTION CHUTE: (Functional location
11643756 (19207)
PC 5305-983-6651 SCREW: (To attach extension) (Functional BC ea 2 2 3-7
location)
MS16998-27 (96906)
REPAIR PARTS FOR 7. 62MM MACHINE GUN
PC 1005-972-0196 BARREL ASSY: (Hull right sponson) BC ea 1 1 5-11,12

7792874 (19204) 13-1 4
P C R 1005-921-6317 BREECHBLOCK ASSEMBLY: (In spare parts box) BC ea 1 1 5-11,12
11013422 (19205) 13-1 12
P C R 1005-937-8256 EXTENSION ASSEMBLY, BARREL: (Used w/M73 B ea 1 1 5-11,12
only) (In spare parts box)
11013360 (19204)
P C R 1005-832-9612 EXTENSION ASSEMBLY, BARREL (Used on M73E1 C ea 1 1 13-1 13
only) (In spare parts box)
11013432 (19204)
B-11
C6, TM 9-2350-230-12
(1) (2) (3) (4) (5) (6) (7)

REPAIR PARTS FOR 7. 62MM MACHINE GUN - Cont’d.

PC 5340-209-6975 RING, RETAINING: Ext., S, Phos - Ctd., 0. 302 ID, B ea 3 3 5-11,12
3/8 shaft dia. (In spare parts box)
MS16333-3037 (96906)
PC 5340-209-6975 RING, RETAINING: Ext. ,S, Phos - Ctd., 0. 302 ID, C ea 2 2 13-1 15
3/8 Shaft Dia (In spare parts box)
MS16333-3037 (96906)
PC 1005-856-7995 SPRING, HELICAL COMPRESSION: 9. 100 Free Lg. , BC ea 2 2 5-11,12
Driving (In spare parts box) 13-1 9
7792838 (19207)
PC 1005-832-9613 STUD, MOUNTING, CHARGER: (In spare parts box) C ea 1 1 13-1 17
(Used w/M73E1 only)
11013434 (19204)
TOOLS AND EQUIPMENT FOR 7. 62MM MACHINE GUN
1005-714-5250 BOX, SPARE PARTS: (Empty) (In driver’s BC ea 1 B-6 6

compartment)
7790683 (19205)
1005-556-4174 BRUSH, CLEANING, SMALL ARMS: Bore (in case) BC ea 4 B-6 8
5564174 (19204)
1005-650-4508 BRUSH, CLEANING, SMALL ARMS: Receiver BC ea 1 B-6 5
(In case)
7790342 (19205)
1005-690-3115 BRUSH, CLEANING, SMALL ARMS: Chamber BC ea 1 B-6 7
(In case)
7790452 (19205)
1005-694-1662 BUFFER, CLEANING ROD: (In case) BC ea 1 B-6 11
7268275 (19205)
1005-550-6573 CASE, SMALL ARMS CLEANING ROD: (Turret BC ea 1 B-6 1
oddment box)
5506573 (19204)
14933-733-4759 COMBINATION TOOL: (In spare parts box) BC ea 1 B-8 4
’7791083 (19205)
4933-652-9950 EXTRACTOR, RUPTURED CARTRIDGE CASE: BC ea 1 B-6 12
(In spare parts box)
7790352 (19205)
1005-922-9777 FLASH HIDER:(On machine gunr BC ea 1 B-6 13
11013420 (19204)
1005-793-6761 HANDLE ASSY., CLEANING ROD: (In case) BC ea 1 B-6 10
7266115 (19204)
9150-889-3522 LUBRICATING OIL, SEMIFLUID: (LSA) 4 oz BC ea 1 B-6 9
bottle (In spare parts box)
MIL-L-46000 (81349)
5120-242-5966 PUNCH, DRIVE PIN: Straight, 3/4" Ig, 1/8" BC ea 1 5-13
dia. pt.
GG-P-00831 (81348)
B-12
C10, TM 9-2350-230-12
(1) (2) (3) (4) (5) (6) (7)

TOOLS AND EQUIPMENT FOR 7. 62MM MACHINE GUN-

Continued
PC 1005-726-6109 ROD SECTION, CLEANING, SMALL ARM; BC ea 5 B-6 2
(In case)
7266109 (19205)
PC 1005-726-6110 SWAB HOLDER SECTION, SMALL ARMS BC ea 1 B-6 3
CLEANING ROD: (In case)
7266110 (19204)
PC 5120-264-3793 WRENCH: Auto adj., 15" Ig O/A, 0 to 3-5/8 BC ea 1 5-13
min. jaw opening cap (In spare parts box)
GGG-W-631 Type E2 (81348)
3403 SIGHTING AND FIRE CONTROL EQUIPMENT
PC 1220-624-3415 PLATE, INSTRUCTION: (Range card) (In pamphlet ea 1 B-3 5

bag)
8724207 (19207)
PC 1240-950-1605 BORESIGHT AID ASSEMBLY: u/o XM44 Periscope (In ea 1 B-3 6
pamphlet bag)
10516830 (19200)
PC 5340-792-9974 PLUG, PROTECTIVE, DUST AND MOISTURE ea 1 10-49.1
SEAL: cover, telescope (Functional location)
11636162 (19207)
PC 1240-238-5778 COVER, PERISCOPE: plastic (for XM44E series to ea 2
cover cavities when head and body are separated)
11732210 (19200)
3404 PARTS, SIGHTING AND FIRE CONTROL
PC 6135-120-1010 BATTERY, DRY, 1. 5v "C" size Type BA 42 ea 2

MIL-B-18 (81349)
PC 6240-155-7836 LAMP, INCANDESCENT: 28v .04 amp., no. 327 ea 3 3
(In bulb box) (See table 5-6)
MS25237-327 (96906)
PC 6240-817-9803 LAMP, INCANDESCENT: 6v, .70 amp, no. 316 ea 3 3
(In bulb box) (See table 5-6)
MS25231-316 (96906)
PC 6240-921-4493 LAMP, INCANDESCENT (In bulb box) (See table 5-6) ea 3 3
8624583 (19200)
B-13
C10, TM 9-2350-230-12
(1) (2) (3) (4) (5) (6) (7)

GROUP 48 - FOOD PREPARATION EQUIPMENT RANGE

4815 RANGE
PC 7310-285-6155 STOVE, COOKING: Gasoline, M1950 w/case (In ea 1

driver’s compartment)
MIL-S-10736 (81349)
Consisting of:
PC 7310-281-2215 STOVE: M1950 ea 1 B-1 9
MIL-S-10736 (81349)
PC 7310-379-2418 CASE: M1950 Stove ea 1 B-1 10
264985PC 25 (10001)
GROUP 76 - FIRE FIGHTING EQUIPMENT COMPONENTS
7603 FIRE EXTINGUISHERS

PC 4210-555-8837 EXTINGUISHER: Fire Portable 2-3/4 lbs. monobromotri- ea 1 2-18
flourmethane (CF3BR), w/bracket (At turret commander’s
station)
MIL-E-52031 (81349)
B-14
C 10, TM 9-2350-230-12
Section B-3. MAINTENANCE AND OPERATING SUPPLIES
(1) (2) (3) (4) (5) (6)
FEDERAL QTY REQ’D. QTY REQ’D.
COMPONENT STOCK FOR INITIAL FOR 8 HOURS
APPLICATION NUMBER DESCRIPTION OPERATION OPERATION NOTES
The following items are listed

for informational purposes
only.
Air pressure gage 8030-134-3692 SELANT LIT:

5702948 (19207)
All armament CARBON REMOVING Usage restricted to

COMPUND: organizational main-
P-C-111 (81348) tenance
6850-965-2332 5 gal pail
All armament CLEANING COMPUND,

RIFLE BORE: solution type
MIL-C-372 (81349)
6850-224-6565 2 oz plastic bottle
6850-224-6657 6 oz can
6850-224-6663 1 gal can
Ammunition detent LUBRICATING OIL,

CBSS check valve SEMIFLUID:
MIL-L-46150 (81349)
9150-949-0323 8 oz plastic tube
Compressor LUBRICATING OIL, AIR

COMPRESSOR:
BMS3-7A (82918)
9150-753-4667 1 qt
Driver’s rotatable ADHESIVE: syn-rbr base,

hatch type II
Driver’s escape MIL-A-5092 (81349)
hatch cover
Headlight assembly 8040-664-4318 1 pt can
Engine ANTIFREEZE:
0-A-548m, Type 1 (81348)
6850-243-1992 1 gal can
6850-224-8730 5 gal pail
ANTIFREEZE: arctic type

MIL-C-11755 (81349)
6850-174-1806 55 gal drum
B-15
C 10, TM 9-2350-230-12
Section B-3. MAINTENANCE AND OPERATING SUPPLIES
(1) (2) (3) (4) (5) (6)
Engine, transmission LUBRICATING OIL, ENGINE:
heavy duty
MIL-L-2104 (81349)
9150-265-9425 OE-10 1 qt can
9150-265-9428 5 gal can
9150-265-9433 OE-30 1 qt can
9150-265-9435 5 gal can
OES LUBRICATING OIL,

ENGINE: sub-zero
MIL-L-10295 (81349)
9150-242-7602 1 qt can
9150-242-7603 5 gal pail
9150-242-7604 55 gal drum
Fire Control LUBRICATING OIL,

INSTRUMENT:
MIL-L-6085 (81349)
9150-664-6518 1-1/2 oz bottle
9150-223-4129 1 qt can
Fire Control equip- GPS GREASE, AIRCRAFT
9150-273-8633 8 oz tube
9150-269-8255 1 lb can
Grease Gun GREASE, AUTOMOTIVE AND

4930-253-2478 ARTILLERY:
MIL-G-10924 (81349)
9150-935-1017 14 oz cartridge
Gun-launcher SILICONE COMPOUND:

Headlight assy MIL-S-8660 (81349)
6850-880-7616 8 oz tube
Headlight assembly SEALING COMPUND:

tape, type III
MIL-S-11030 (81349)
8030-965-2438 60 ft roll
Lens (Missile ETHYL ALCOHOL,

Subsystem) ABSOLUTE, ACS:
0-C-265 (81348)
6810-242-3645 1 gal can
B-16
C 10, TM 9-2350-230-12
(1) (2) (3) (4) (5) (6)
Optical, Fire 6850-227-1887 CLEANING COMPUND, 1 qt 1. Clean exterior
Control LENS: Liquid (1 qt container) optical surfaces, eye-
Instruments (1) lens, objective lens,
(2) (3) (4) windows, etc.
Reservoir, Peris- 6850-558-1248 ANTI-ICING AND DEICING 1 gal 2. CAUTION: Do not
cope Washer & DEFROSTING FLUID: touch optics will bare
Pump Assy (1 gal container) fingers. Oil and acid
MIL-A-8243 (81349) from fingers will etch
Periscope M47/ optics if not removed.
M48 (4)
Periscope XM44/ 3. CAUTION: In cold
weather, avoid blowing
breath on optical sur-
Telescopes 8020-224-8024 BRUSH ARTIST: mtl ferrule, 1 faces to prevent depos-
Periscopes round taper point, style 9, its of condensation
Camel hair, 1-1/16 lg, 1/4 which may freeze.
in. dia at ferrule
4. To prevent marring
optical windows,
always pump defrost-
ing fluid or water on
dry or dusty head
windows before opera-
tion of wipers.
Periscope 6810-543-4041 POTASSSIUM HYDROXIDE:
XM44 series electrolyte
emergency
battery
Telescopes 6640-285-4694 PAPER, LENS: 100 sheets
Persicopes (7 x 11) in envelope
NNN-P-40, Type 4 (81348)
Radio equipment CLEANING COMPOUND,
SOLVENT:
MIL-C-18718 (81349)
6850-597-9765 1 gal can
Recoil mechanism GMD GREASE, MOLYBDE-
NUM DISULFIDE: liquid,
gelling agent
MIL-G-21164 (81349)
9150-223-4001 1 lb can
9150-223-4004 5 lb can
9150-965-2003 35 lb pail
OHT HYDRAULIC FLUID,
PETROLEUM BASE:
MIL-H-6083 (81349)
9150-935-9807 1 qt can
9150-935-9808 1 gal can
Small Arms 8020-244-0153 BRUSH ARTISTS: metal
ferrule, flat chisel edges,
7/16w, 1-1/8 lg, exposed
bristle
H-B-241, Style 5 (81348)
B-17
C 9, TM 9-2350-230-12
(1) (2) (3) (4) (5) (6)
Small Arms 7920-205-2401 BRUSH, CLEANING, TOOL

AND PARTS: rd, 100 percent
tampico fiber, 1-1/16 brush
dia (at ferrule), 2-7/8 brush
lg (clear of block)
Small Arms PL-special LUBRICATING
OIL, GENERAL PURPOSE:
VV-L-800 (81348)
9150-273-2389 4 oz can
9150-231-6689 1 qt can
Small Arms LSA LUBRICATING OIL, For 7, 62MM
SEMIFLUID: AUTOMATIC machine gun only
WEAPONS
MIL-L-46000 (81349)
9150-889-3522 4 oz tube
9150-687-4241 1 qt can
9150-753-4686 1 gal pall
Small Arms LAW LUBRICATING OIL,
WEAPONS: LOW TEMP,
CORROSION AND OXIDATION
RESISTANT
MIL-L-14107 (81349)
9150-664-0038 4 oz can
9150-292-9689 1 qt can
9150-292-9687 5 gal pail
Small Arms RAG WIPING: cotton white,
bleached
7920-205-1711 50 lb bale
7920-234-8467 100 lb bale
1005-288-3565 SWAB, SMALL ARMS
CLEANING: cotton, 2-1/2
sq, 1000 in pkg
5019316 (19205)
Turret bearing GAA GREASE, AUTOMOTIVE
turret and cupola AND ARTILLERY:
traversing ring MIL-G-10924 (81349)
and pinion gears
9150-190-0904 1 lb can
9150-190-0905 5 lb can
Turret and cupola GG-1 GREASE, GRAPHITE:
race ring seal soft VV-G-671, Grade 1
(81348)
9150-257-5370 1 lb can
B-18
C 9, TM 9-2350-230-12
(1) (2) (3) (4) (5) (6)
Turret electrical ADHESIVE: MIL-A-46106

system, XM44 (81349)
Series periscope
8040-867-4358 5 oz tube
Turret traverse GIA GREASE, AIRCRAFT
mech gear box, AND INSTRUMENT MIL-G-
fire control equip- 23827 (81349)
ment
9150-985-7244 4 oz tube
9150-985-7246 1 lb can
9150-985-7247 5 lb can
ADHESIVE: reclaimed-ru,
liquid, general purpose
MIL-A-5092, Type 1 (81349)
8040-262-9025 4 oz tube
8040-262-9028 1 pt can
8040-262-9031 1 qt can
8020-242-7266 BRUSH, PAINT: flat, mtl
bound, med grade 3 w
H-B-420 (81348)
CLOTH, ABRASIVE: aloxide,
jean cloth back, closed coat,
9 w, 11 lg P-C-451, Type 1,
Class 1 (81348)
5350-192-5047 grit no. 80 50 sheet sleeve
CA - CLOTH, ABRASIVE:
crocus, ferric oxide and
quartz, jean-cloth-back,
closed coat, 9 w, 11 lg
P-C-458 (81348)
5350-221-0872 50 sheet sleeve
COMPOUND, non-slip, o. d.,
color no. X24087
5610-782-5555 1 qt can
5610-782-5556 1 gal can
SD - DRY CLEANING
SOLVENT:
P-D-680, Type 1 (81348)
6850-664-5685 1 qt can
6850-281-1985 1 gal can
B-19
C 6, TM 9-2350-230-12
(1) (2) (3) (4) (5) (6)
ENAMEL: semi-gloss, rust

inhibiting, od no. X24087
TT-E-485, Type IV (81348)
8010-297-2105 1 gal can
8010-577-4381 5 gal pail
ENAMEL: semi-gloss, rust
inhibiting, od no. X24087
TT-E-485, Type II (81348)
8010-598-5936 12 oz can Pressurized
8010-297-2109 1 pt can
ENAMEL: alkyd, lusterless,
od no. X34087
TT-E-527 (81348)
8010-297-0560 1 gal can
8010-297-0561 5 gal pail
GO LUBRICATING OIL, GEAR:
UNIVERSAL TYPE
MIL-L-2185, GRADE 80
(81349)
9150-905-9100 1 gal can
9150-577-5840 5 gal pail
GOS LUBRICATING OIL,
GEAR: UNIVERSAL TYPE,
SUB-ZERO
MIL-L-10324 (81349)
9150-261-7904 1 qt can
9150-257-5440 5 gal pail
PL - medium LUBRICATING Not for small arms.
OIL, GENERAL PURPOSE:
MIL-L-3150 (81349)
9150-231-2360 2 oz can
9150-231-2361 1 qt can
9150-231-2356 5 gal pail
8135-551-1245 TAPE, ADHESIVE: pressure
sensitive, water resistant,
od 7, 4 in. x 60 yd roll
JAN-P-127, Type 1 Grade B
TPM - THINNER, PAINT,
MINERAL SPIRITS:
TT-T-291, Grade 1 (81348)
8010-242-2089 1 gal can
8010-558-7026 5 gal pail
B-20
C6, TM 9-2350-230-12
Figure B-1. Basic issue items
B-21
C6, TM 9-2350-230-12
B-22
C6, TM 9-2350-230-12
B-23
C6, TM 9-2350-230-12
B-24
C6, TM 9-2350-230-12
B-25
C6, TM 9-2350-230-12
B-26
C 13, TM 9-2350-230-12
APPENDIX III
MAINTENANCE ALLOCATION CHART
Section C-1. GENERAL
NOTE. All references to M551A1 in this appendix pertain to vehicles equipped with laser range finder.
C-1. General
The implementation of field maintenance tasks upon this
This Maintenance Chart designates overall responsibility end item or component will be consistent with the
for the performance of maintenance functions on the assigned maintenance operations in section C-2.
AR/AAV, M551, M551A1, or a component.
C-2. Maintenance Functions
Operation Definition
INSPECT To determine serviceability of an item by comparing

its physical, mechanical, and electrical characteris-
tics with established standards.
TEST To verify serviceability and to detect electrical or

mechanical failure by use of test equipment.
SERVICE To clean, to preserve, to charge, to paint, to drain,

and to add fuel, lubricants, hydraulic fluids, cooling
agents, deicing fluids, and air.
ADJUST To rectify to the extent necessary to bring into pro-

per operating range.
ALIGN To adjust specified variable elements of an item to

bring to optimum performance.
CALIBRATE To determine the corrections to be made in the read-

ings of instruments or test equipment used in precise
measurement. Consists of the comparison of two in-
struments, one of which is a certified standard of
known accuracy, to detect and adjust any discrepancy
in the accuracy of the instrument being compared with
the certified standard.
C-1
C9, TM 9-2350.-230-12
Operation Definition
INSTALL To set up for use in an operational environment such

as an emplacement, site, or vehicle.
REPLACE To replace unserviceable items with serviceable like

items.
REPAIR Those maintenance operations necessary to restore an

item to serviceable condition through correction of
material damage or a specific failure. Repair may be
accomplished at each category of maintenance.
OVERHAUL Normally, the highest degree of maintenance performed

by the Army, in order to minimize time work is in
process, consistent with quality and economy of
operation. It consists of that maintenance necessary
to restore an item to completely serviceable condition
as prescribed by maintenance standards in technical
publications for each item of equipment. Overhaul
normally does not return an item to like new, zero
mileage, or zero hour condition.
REBUILD The highest degree of materiel maintenance. It con-

sists of restoring equipment as nearly as possible to
new condition in accordance with original manufactur-
ing standards. Rebuild is performed only when requir-
ed by operational considerations or other paramount
factors and then only at the depot maintenance cate-
gory. Rebuild reduces to zero the hours or miles the
equipment, or component thereof, has been in use.
C-3 Explanation of Format subassemblies, and modules on which maintenance is

authorized.
a. Section C-2.
(3) Column 3, maintenance function.
(1) Column 1, group number. Column 1 Column 3 is divided into 11 columns (subcolumns (a)
lists group numbers, the purpose of which is to identify through (k) , one for each of the maintenance operations
components, assemblies, subassemblies, and modules defined in paragraph C-2.
with the functional group.
(4) Use of symbols. An uppercase letter
(2) Column 2, functional group. Column 2 placed in the appropriate column indicates
lists the noun names of components, assemblies,
C-2
C 9, TM 9-2350-230-12
the lowest category at which that particular maintenance b. Section C-3.

function is to be performed.
(1) Tool or test equipment reference code.
Code Explanation This code consists of a number assigned to each tool or
C Crew/operator item of test equipment and a letter(s) referencing the
0 Organizational maintenance maintenance function(s) for which the equipment is
F Direct support maintenance required.
H General support maintenance
D Depot maintenance (2) Maintenance category. The maintenance
code specifies the lowest level of maintenance
(5) Column 4, tools and equipment. Column 4 authorized to use the tool or test equipment.
specifies, by code, those tools and test equipments
required to perform the designated maintenance of the (3) Nomenclature. This column lists the name
functional group. The code consists of a number or identification of the tool or test equipment.
identifying a particular tool or item of test equipment (sec
C-3) and a lowercase letter(s) correlating that tool or test (4) FSN and tool number columns. The
equipment with the specific maintenance operation(s) for Federal stock number and part or reference number of
which it is required (colm 3). the tool or test equipment are listed for identification
purposes.
(6) Column 5, remarks. Self-explanatory.
(C-2.2 blank)/C-2.1
C9, TM 9-2350-230-12
SECTION C-2 MAINTENANCE ALLOCATION CHART

ARMORED RECONNAISANCE/AIRBORNE ASSAULT VEHICLE: FULL TRACKED, 152 MM, M551
(1) (2) (3) (4) (5)
GROUP MAINTENANCE FUNCTIONS TOOLS AND REMARKS
NUMBER FUNCTIONAL GROUP A B C D E F G H I J K EQUIPMENT
GROUP 01 ENGINE
0100 POWER PLANT O 1 (h) (g)
MOUNT AND SUPPORT, ENGINE O
ENGINE F H
0101 HEAD, CYLINDER F F
0102 PULLEY, CRANKSHAFT F
SEAL, OIL, CRANKSHAFT F
0103 FLYWHEEL F
0106 FILTER, OIL, ENGINE O O
ELEMENT, ENGINE OIL FILTER O
COOLER, OIL, ENGINE O F
VALVE, (BYPASS) F F
HOSES, LINES AND FITTINGS O F
REGULATOR, PRESSURE ENGINE

OIL SYSTEM F
HOSE, BREATHER, CRANKCASE O
TANK, AIR BOX/BREATHER O
C-3
C9, TM 9-2350-230-12
(1) (2) (3) (4) (5)
CAP, OIL ENGINE O
TUBE AND FITTINGS, DRAIN, AIR BOX O
PAN, OIL, ENGINE O F
GAGE, DIPSTICK O
SCREEN, OIL, ENGINE F
0108 MANIFOLD, EXHAUST O
0109 0109 QUILL, AIR BLOWER DRIVE F
DRIVE, GEAR, AIR BLOWER F
GROUP 03 FUEL
0301 INJECTOR, FUEL SYSTEM F H
TUBES AND FITTINGS, FUEL INJECTOR F
LEVER, LINK AND TUBE CONTROL, F F

FUEL INJECTOR
0302 PUMP, FUEL, ENGINE O F
0304 CLEANER, AIR O O
HOSES AND CLAMPS O
ELEMENT C O
C-4
C9, TM 9-2350-230-12

NUMBER FUNCTIONAL GROUP (a) (b) (c) (d) (e) (f) (g) (h) (I) (j) (k) EQUIPMENT
0305 TURBOCHARGER AND BLOWER F H
DUCT, HOSE AND PIPES BLOWER O

AND TURBOCHARGER
0306 TANK, FUEL F
CAP, FUEL, FILLER O
LINES, HOSES AND FITTINGS, F

FUEL SYSTEM
VALVE, SHUT-OFF, FUEL O
0308 GOVERNOR F F H
0309 ELEMENT, FUEL FILTER O
FILTERS, FUEL O
0310 AIR BOX (FLAME) HEATER O

COMPONENTS
ACCUMULATION, AIR BOX O O
PUMP, HAND, AIR BOX O
LINES AND FITTINGS O
0312 LINKAGE, CONTROL, THROTTLE AND O O

FUEL SHUT-OFF
C-5
C9, TM 9-2350-230-12
(1) (2) (3) (4) (5)
GROUP 04 EXHAUST
0401 MUFFLER AND PIPES O
GROUP 05 COOLING
0501 RADIATOR O F
TANK, SURGE AND CAP O
0502 SHROUD, RADIATION O
0503 PIPES, HOSES AND CLAMPS O
THERMOSTAT O
0504 PUMP, COOLANT O F
BELTS, PUMP C O O
0505 CLUTCH, FAN, DRIVE F H
FAN, COOLING O 2(h)
BELTS, FAN C O
GROUP 06 ELECTRICAL
0601 GENERATOR O F
C-6
C 9, TM 9-2350-230-12

DRIVE, GENERATOR O F
TENSIONER, GENERATOR O
0602 REGULATOR, VOLTAGE O O F
0603 STARTER O F
0607 PANEL, SWITCH, DRIVER’S O
PANEL, INDICATOR, O F
DRIVER’S
HARNESS, PANEL F O
LAMPS C
DRIVE COMPONENTS, O
TACHOMETER/ODOMOETER
INSTRUMENTS, INDICATOR F
PANEL
0608 RELAY, MASTER O
RELAY, STARTER O
SWITCHES O
RELAY BILGE PUMP O
RECEPTACLES O
C-7
C 14, TM 9-2350-230-12

(1) (2) (3) (4) (5)
BREAKERS, CIRCUIT O
0609 LIGHTS O
LAMP C
0610 TRANSMITTERS AND O

SWITCHES
0612 BATTERY C O F
CABLE, BATTERY O O
0613 HARNESS, GENERATOR O O

REGULATOR TO GENERATOR
HARNESS, HULL AND F O

POWER PLANT
0614 RING, ELECTRICAL F D 3(b)

CONTACT
SLIP RING, CUPOLA F F 4(g), (d), (e)

ELECTRICAL
C-8
C 14, TM 9-2350-230-12

0616 BLOWER, TURRET O F

VENTILATING
0618 POWER SUPPLY, TURRET O F O D 5 (b), (d), 98(b),

CONTROL (d)
POWER SUPPLY, CONVEN- O 98 (b) (d)

TIONAL WEAPONS
POWER SUPPLY, GRENADE O 98(b) (d)

LAUNCHER
BOX, LOADER’S CONTROL O F 3(b) 98 (b) (d)
BOX, CUPOLA CONTROL O F 3(b)
BOX, CUPOLA TRAVERSE O F 3(b)

MECHANISM CONTROL
COMMANDER’S CUPOLA O F
TRAVERSE MECHANISM
CONTROL BOX ASSEMBLY
W/SUPPRESSOR (M551A1
ONLY)
COMMANDER’S CUPOLA/ O F
LASER CONTROL ASSEM-
BLY (M55A1A ONLY)
REMOTE SWITCH ASSEMBLY O F

(M551A1 ONLY)
RESISTOR BOX ASSEMBLY O F

(M551A1 ONLY)
C-9
C 14, TM 9-2350-230-12

(1) (2) (3) (4) (5)
SWITCHES & CAMS, LIMIT, F F 3(b), 5(b), (d)

ELEVATION AND DEPRES 98 (b) (d)
SION
SWITCH, TRAVERSE INTER- O F F 5(d), (b) 98 (b)
FERENCE (d) 3 (b)
SWITCH, IN-BATTERY O O F 3(b) 98 (b) (d)
LIMIT
SWITCH, TRANSMITTER O O O 3(b), 6(d) 98 (b)
DOOR (d)
BOX, TURRET CONTROL O O O F 5(d), (b) 98 (b)
ACCESSORY (d)
PRINTED CIRCUIT BOARDS O O O 5(b), (d) 98 (b) (d)
RELAY ASSEMBLY O O 5(b), (d) 98 (b) (d)
BOX, RELAY WEAPONS O O F 98 (b) (d)
BLASTING MACHINE O O F 3(b)
SOLENOID, GRENADE C O O 3(b)
LAUNCHER
BOX, RETICLE DIMMER F 3(b)
POWER SUPPLY, EMERGENCY, O F 3(b)
TELESCOPE & PERISCOPE
CONTROL SELECTOR, GUN F 3(b) 5 (b) (d)
AND TURRET 98 (b) (d)
C-10
C 9, TM 9-2350-230-12

BOX, CIRCUIT CUTOUT O F 3(b), 5(b), (d)

98(b), (d)
0619 AMPLIFIER INTEGRATOR O O O F 5(b), (d) 98 (b) (d)
ASSY
MOTOR GENERATOR ASSEM- O O O F D 3(b) 98 (b) (d)

BLY
GYRO SELECTOR ASSEMBLY O O F 3(b), 5(b), (d)

98 (b)(d)
0620 HARNESS, TURRET & F F 3(b), 5(b), (d)

CUPOLA, ELECTRICAL 98 (b) (d)
DRIVE, WEAPON & ACCES-
SORY SYTEMS
SPECIAL PURPOSE CABLE F F

ASSEMBLY (M551A1 ONLY)
GROUP 07 TRANSMISSION
0700 TRANSMISSION F H
PLUG, OIL DRAIN O
BRAKE O
0711 LINKAGE, CONTROL, SHIFT O O
0721 COOLER, OIL, TRANSMIS- O F

SION
C-10.1
C 9, TM 9-2350-230-12

(1) (2) (3) (4) (5)
SEAL, OUTPUT SHAFT F
FILTER, OIL O O F
INDICATOR, OIL LEVEL O
VALVE, CONTROL F F
GROUP 12 BRAKE
CONTROLS
1206 CONTROLS, BRAKE O O O 7 (d)
GROUPS 13 TRACKS AND

SUSPENSION
1301 ARM, ROADWHEEL O O 8 (h), 9(g), 10 (h)

11 (h), 12 (h),
13 (h)
HOUSING, ROADWHEEL ARM, O F 14 (h), 15 (h),

FRONT AND REAR 16 (h), 17 (h)
HOUSING, ROADWHEEL ARM, O O 14 (h), 15 (h),

INTERMEDIATE 16 (h), 17 (h)
BAR, TORSION O 18 (h)
ANCHOR, TORSION BAR O 19 (h)
C-10.2
C 9 TM 9-2350-230-12

PLUG, SIGHT, OIL O
WHEEL, ROAD O
1303 HOUSING, IDLER, W/SPINDLE O O
WHEEL, IDLER O
HUB, IDLER WHEEL O F 15(h), 11 (h), 20 (h)
ADJUSTER, TRACK, HYDRAULIC O F
PLUG, RELEASE, LUBRICATION AND O

PRESSURE
SPROCKET AND WHEEL O 21(a)
SHAFT, DRIVE, SPROCKET O 22 (h), 23(h), 15(h), 24(h),

17(h), 25(h), 26(h)
HUB, SPROCKET O O
SUPPORT, SPROCKET HUB O
1305 TRACK C C O 27 (i), 28 (i)
GROUP 14 CONTROLS
1401 LINKAGE, CONTROL ATEER O O
GROUP 15 TOWING SHACKLE
1503 SHACKLE, TOWING O
GROUP 16 SHOCK ABSORBERS
ABSORBERS, SHOCK O F
C-11
C 9, TM 9-2350-230-12

(1) (2) (3) (4) (5)
GROUP 18 HULL
1801 SURFBOARD F
CONTROLS, SURFBOARD O O
BARRIER F O
HATCH, DRIVER’S ROTATABLE F
LATCHES O
SEALS, HATCH O
1806 BACKREST, SEAT, DRIVER’S O
CUSHION, SEAT O
MECHANISM, SEAT, DRIVER’S O
BELT, SEAT O
1808 RACKS, AMMNITION STOWAGE O
GROUP 19 TURRET
1901 TURRET, RACE COMPONENTS F F
LOCK, TURRET TRAVERSE O
MECHANISM, SEAT O
COMMANDER’S SUBFLOOR, SCREENS F F
C-12
C 13 TM 9-2350-230-12

HATCH, LOADER’S O
MOUNTING, ANTENNA F O
RACE COMPONENTS, CUPOLA F
ROTATABLE FLOOR, TURRET H F
1903 MECHANISM, CUPOLA F F 29 (d)

TRAVERSE
HATCH, CUPOLA F
SERVOMETER, CUPOLA F F O F
TRAVERSE
COMMANDER;S CUPOLA F F F F
TRAVERSE MECHANISM
(M551A1 ONLY)
LASER CONTROL HANDLE O F

(M551A1 ONLY)
INDEX POINTERS (M551A1 O

ONLY)
PERISCOPE STOP (M551A1 O

ONLY)
BALLISTIC COVERS O
(M551A1 ONLY)
BALLISTIC SHIELD O F
ASSEMBLIES (M551A1
ONLY)
C-13
C 19 TM 9-2350-230-12

(1) (2) (3) (4) (5)
1904 MECHANISM,, TURRET F F 30 (d), 31 (d),

TRAVERSE 32 (d), 33(d)
36(d)
MECHANISM, GUN ELEVA- F F 34(d), 35(d)

TION
HANDLE ASSY, CONTROL, C O F 5 (b), (d)

GUNNER’S AND COMMAND-
ER’S
SERVOMETER, TRAVERSE O F 5 (b), (d)

AND ELEVATION
1906 BOXES, STRAPS AND O

RACKS, STOWAGE
1907 AMMO BOX, MACHINE GUN F O
GROUP 22 HULL MISCEL-

LANEOUS ACCESSORIES
2202 BOX, GROUND, INTERCOM O
LAMP, INTERCOM BOX
C-14
C 9 TM 9-2350-230-12

2205 PUMP, BILGE O F
HOSE, CLAMPS AND FIT- O

TINGS
2207 HEATER, PERSONNEL O H
BOX, CONTROL, HEATER O
DUCT, FLEXIBLE O
IGNITER O
LAMPS, CONTROL BOX, C

HEATER
PUMP, FUEL FILTER, O

VALVE AND LINES
2210 PLATE, DATA, VEHICLE O
C-14.1
C 9 TM 9-2350-230-12

(1) (2) (3) (4) (5)
GROUP 33 SPECIAL
PURPOSE KITS
3303 KIT, WINTERZATION F O F
KIT, AIR FILTER UNIT O O
GROUP 34 ARMAMENT,
SIGHTING AND FIRE
CONTROL, AND GUIDANCE
AND CONTROL MATERIEL
3401 152MM GUN-LAUNCHER,

M81, M81 MOD, M81E1
AND MOUNT
MECHANISM GROUP, BREECH C F F 37 (d), (g), 38 (d),

ACTUATING (g), 39 (d), (g),
40 (d), (g)
C-14.2
C11, TM 9-2350-230-12
MAINTENANCE FUNCTIONS TOOLS AND REMARKS

FUNCTIONAL GROUP (a) (b) (c) (d) (e) (f) (g) (h) (I) (j) (k) EQUIPMENT
CANNON, PRESSURE VESSEL ASSY F C F F F 41(g), lb), 420)

M81 MOD/M81E1
AMMUNITION DETENT, type I or type II O O
SWITCH, SOLENOID VALVE O 3(b)
EVACUATOR CHAMBER C C 42(g) (h)
SCAVENGER SYSTEM, CLOSED
BREECH F
AMMUNITION DETENT, type III F F
CHECK VALVE O O 44 (c), 43 (g) ) (h)
45 (a) (g) (i), 37 (d)
AIR FILTER O
MOTOR, ELECTRIC DRIVE O
ACTUATING SWITCHES, BREECH O
WIRING HARNESS O 47 (h). 48 (c), 49 (c)
50 (c) (h) (i), 3 (b)
EXTRACTOR GROUP,MISSILE O O
FIRING PROBE ASSEMBLY O O F 51(c)(h), 52 (c)(h),
53(c)(h), 40(d) (g),
54 (d) (g) (h)
RECOIL MECHANISM C F
BUFFER ASSEMBLY, COUNTER
RECOIL C O F
MOUNT, CO-AXIAL 7. 62MM MACHINE C o
GUN
RESERVOIR, RECOIL MECHANISM C O
RELIEF VALVE ASSEMBLY F F
COVER AND DOOR, TRANSMITTER F
C-15
C10, TM 9-2350-230-12
SECTION C-2 - MAINTENANCE ALLOCATION CHART

ARMORED RECONNAISSANCE/AIRBORNE ASSAULT VEHICLE: FULL TRACKED, 152MM, M551
(1) (2) (3) (4) (5)
NUMBER FUNCTIONAL GROUP a b c d e f g h i j k EQUIPMENT
CONTROL, TRANSMITTER O O
MOUNT, GRENADE LAUNCHER C O O F
GRENADE LAUNCHER TUBE ASSEMBLY C O O F
3402 SMALL ARMS
MACHINE GUN, 7.62MM M73/M219
REFER TO TM 9-1005-233-25
MACHINE GUN, CAL.. 50 M2 HB,
REFER TO TM 9-1005-213-25
3403 SIGHTING AND FIRE CONTROL
MATERIEL
INDICATOR AZIMUTH C C O F H
MOUNT, TELESCOPE M149 OR M165 C C C O F D 55(c), 56(c), 57(c), 58(c),
59(b), 60(a), 61(e), 62(f),
63(c), 64(c), 65(c), 66(d)(e)
67(c), 68(b), 69(c), 70(d),
71(c), 72(g) (h)
PERISCOPE, M37 C C O F
PERISCOPE, XM44 SERIES C C O O F D 55(c), 56(c), 57(c), 58(c),
73(d), 74(d), 75(d), 76(d),
77(d), 78(h), 79(f), 63(c),
80(e), 65(c), 66(d) (e), 81(d),
67(c), 69(c), 82(a), 83(b),
84(b), 72(g)(h)
BATTERY, STORAGE: 6v C O O
(emergency)
LINK ASSY C C O F F
MOUNT ASSY C C F F H
PANEL ASSY C C F F H
PLATE ASSY C C O F
C-16
C9, TM 9-2350-230-12

WASHER, PUMP AND RESERVOIR C C O F H

ASSY
PERISCOPE, M47 C C O O 55(c), 56(c), 57(c), 58(c),
85(b), 63(c), 65(c), 67(c),
68(b), 69(c)
MOUNT ASSY C C O F H
SEAL ASSY C C O
WASHER, PUMP AND RESERVOIR ASSY C C O O H
WIPER ASSY C C F O H
PERISCOPE, M48 C C O O D 55(c), 56(c), 57(c), 58(c),
87(d), 85(b), 60(a), 86(d),
77(d), 88(a), 63(c), 65(c),
81(d), 67(c), 68(b), 69(c),
89(b), 90(b), 91(d), 92(g) (h),
71(g) (h)
HEADREST ASSY C C O
QUADRANT, F. C. M13A1C C C O O F H
QUADRANT, GUNNER’S M1AL C C F O F H
TELESCOPE, M127 OR M119 C C C C O O D 55(c), 56(c), 57(c),58(c),
93(b), 77(d), 94(a), 63(c),
65(c), 67(c), 68(b), 69(c),
71(c), 95(g), 72(g), (h)
HANGER ASSY C C O
GROUP 3405 GUIDANCE AND
CONTROL SYSTEM
3405 POWER SUPPLY C C C F O F F D 50(c)(g))(h)
ELECTRONICS COMPONENTS ASSY F F F F D D D
COUNTDOWN MODULE F F F F F D
C-17
C9, TM 9-2350-230-12

(1) (2) (3) (4) (5)

DRIVER MODULE F F F D D D
D. C. SUPPLY MODULE F F F F D D D
OUTPUT TRANSFORMER MODULE F F F F F D
PRIME POWER FILTER MODULE F F F F F D
POWER SUPPLY MODULE F F F F D D D
POWER TRANSISTOR MODULE F F F F F D
VOLTAGE REGULATOR MODULE F F F F D D D
SWINGING CHOKE MODULE F F F F F D
WIRING HARNESS ASSEMBLY F F F F D
OPTICAL TRANSMITTER C C C F F O F F D 96(g) (h), 6(d)g)(h), 97 (g)(h),
50 (c) (g) (h) (i)
RETICLE ASSEMBLY F F F F
OPTICS BARREL RETICLE ASSEMBLY F F F D D D
OPTICAL INSTRUMENT CELL ASSEMBLY F F F D D D
ADJUSTABLE BRACKET ASSEMBLY LH F F F F
ADJUSTABLE BRACKET ASSEMBLY RH F F F F
MIRROR SUBASSEMBLY F F F F D D D
TRANSMITTER STARTER F F F F F D
FILTER PANEL F F F F F D
OPTICAL TRACKER C C C F O F F D 97(g)(h), 6 (d)(g)(h), 50(g)
(h)(c)(i)
DETECTOR SIGNAL AMPLIFIER F F F F F F D
C-18
C9, TM 9-2350-230-12

OPTICAL TRACKER SUBASSEMBLY F F F F F F D

IRIS AND DETECTOR SUBASSEMBLY F F F D D D D
DETECTOR SUBASSEMBLY F F F D D D
MODUALTOR C C C O F F D 50(c)(g)(h)(i)
CHASSIS ASSEMBLY F F F F F D
WIRING HARNESS F F F F F
SIGNAL DATA CONVERTER C C C O F F D 50(c)(g)(h)(i)
REFLECTANCE FILTER ASSEMBLY F F F F
AMPLIFIER ASSEMBLY F F F F
DEMODULATOR ASSEMBLY F F F F
TRACKER FILTER ASSEMBLY F F F F
PROGRAM TIMER ASSEMBLY F F F F
COMMAND GENERATOR ASSEMBLY
ERROR AMPLIFIER ASSEMBLY F F F F
TRACKER CONTROL ASSEMBLY F F F F
TEST ACCUMULATOR ASSEMBLY F F F F
ANALOG TEST ASSEMBLY F F F F
TEST DISPLAY ASSEMBLY F F F F
WIRING HARNESS ASSEMBLY F F F F
TEST CHECKOUT PANEL C C C O C F D 50(c)(g)(h)(i)
TEST CHECKOUT PANEL F F F F D
MODULE BOARD ASSEMBLY F F F F
CONNECTOR ASSEMBLY F F F F F
RATE SENSOR C C C O F F D 50(c)(g)(h)(i)
C-19
C9, TM 9-2350-230-12

(1) (2) (3) (4) (5)

CABLE ASSEMBLIES, GUIDED MISSILE F F F

SUBSYSTEM
GROUP 40 ELECTRIC MOTORS AND

GENERATORS (OTHER THAN
ENGINE ACCESSORIES)
4000 ELECTRIC MOTOR (COMPRESSOR) O F F H
4001 ROTOR ASSEMBLY F F
4002 STATOR ASSEMBLY F F
4003 BRUSH HOLDERS, BRUSHES AND F F

HOLDERS
4004 VENTILATING SYSTEM: FAN F
4007 DRIVE COMPONENTS: SHAFT F F
4014 RESISTORS F
F
4016 RELAY F F
C-20
C9, TM 9-2350-230-12

GROUP 42 ELECTRICAL EQUIPMENT
4206 THERMOSTATIC, AUTOMATIC AND F F

MANUAL CONTROL DEVICES: TIMER,.
DUMP
4209 SIGNALING DEVICES: PRESSURE SWITCH F F H
4211 POWER RECEPTACLE F
4216 MISCELLANEOUS WIRING AND F F

FITTINGS: CABLE ASSY
GROUP 50 PNEUMATIC EQUIPMENT
5000 AIR COMPRESSOR ASSEMBLY O F O O F D

(COMPLETE)
5001 CRANKCASE, BLOCK, CYLINDER D

HEAD: CYLINDERS AND HEADS
5002 CRANKSHAFT D
‘ SEAL REAR F
5004 PISTONS, CONNECTING RODS AND D

PLUNGERS: PISTONS AND PLUNGERS
5005 VALVES: VALVES, INTAKE AND D D

EXHAUST
C-21
C9, TM 9-2350-230-12

(1) (2) (3) (4) (5)

5006 LUBRICATION SYSTEM:
OIL PUMP F D
STRAINER O O
DIPSTICK O
RELIEF VALVE F
5007 COMPRESSOR DRIVE:
SHAFT F F
5008 AIR INTAKE:
FILTER O O O
5009 UNLOADER SYSTEM:
MOISTURE SEPARATOR O F
VALVES: RELIEF
CHECK, BACK PRESSURE O F F
5010 COMPRESSOR OR COOLING AND F

HEATING
INTERCOOLERS AND AFTERCOOLER O F
FAN F F
C-22
C9, TM 9-2350-230-12

HEATER, MOISTURE SEPARATOR F F
5015 AIR DISCHARGE SYSTEM:

FITTING O O
GROUP 6700 PRECISION INSTRUMENTS

AND SYSTEMS
6715 TEST SET, ELECTRIC DRIVE CONTROL F
HARNESS, TEST SET O
LAMP, TEST SET O
GROUP 76 FIXED FIRE EXTINGUISHER
7603 CYLINDER, FIRE EXTINGUISHER O O
CONTROLS, TUBES AND FITTINGS O O
C-23
C9, TM 9-2350-230-12
SECTION C-3 TOOLS AND TEST EQUIPMENT REQUIREMENTS

TOOLS OR TEST MAINTENANCE

EQUPMENT CATEGORY NOMENCLATURE FSN TOOL NUMBER
REFERENCE CODE
1 - (h) (g) 0 SLING 4910-907-8990 10954024

2 - (h) 0 WRENCH 5120-907-0698 10954016
3- (b) O MULTIMETER 6625-553-0142 .IL-M-4269
4 - (g) (d) (e) F FIXTURE, POSITIONING BRUSH HOLDER, CONTACT RING 4933-062-4500 11605044
5 - (b) (d) O TEST SET, ELECTRONICS SYSTEM 4933-909-9356 11586473
6 - (d) (g) (h) O SOCKET WRENCH ATTACHMENT 5t20-243-1674 GGG-W-641
7 - (d) O ADAPTER 5120-906-1051 8355955
8- (h) O HANDLE 5120-034-0884 10914196
9- (g) O INSTALLER 4910-906-1064 10954367
10 - (h) O REPLACER 5120-906-1054 10954007-4
11 - (h) O REMOVER AND REPLACER 5120-906-1059 10954003-2
12 - (h) O REMOVER AND REPLACER 5120-906-1060 10954003-1
13 - (h) O WRENCH 5120-901-4283 10954002-1
14 - (h) O PUNCH 5120-910-3738 10954017
15 - (h) O REPLACER 5120-906-1057 10954007-1
13 - (h) O REPLACER 5120-906-1055 10954007-3
17 - (h) O REMOVER ASSEMBLY 11643803
18 - (h) O ADAPTER 5120-901-6181 10954004
19- (h) O REMOVER 5120-907-0696 10954000
20 - (h) O WRENCH 5120-901-4282 10954002-2
21 - (a) O GAGE 5210-906-3706 10954023
22 - (h) O REPLACER 5120-906-1062 10954006-1
C-24
C9, TM 9-2350-230-12


REFERENCE CODE
23 - (h) O REPLACER 5120-906-1063 10954006-2
24- (h) O REPLACER 5120-906-1056 10954007-2
25 - (h) O REMOVER AND REPLACER 5120-906-1061 10954005
26- (h) 0 WRENCH 5120-901-4294 10954002-3
27- (i) O FIXTURE 4910-906-1053 10955739
28- (i) O PIN 5120-678-2795 10861180
29 - (d) F WRENCH LOCK NUT TORQUING 4933-687-8507 10942347
30 - (d) F WRENCH LOCK NUT TORQUING 4933-687-8504 10942154
31 - (d) F WRENCH SPANNER 5120-930-7784 11604983
34 -(d) F WRENCH SPANNER 5120-917-6017 11604985
35 - (d) O WRENCH TORQUE 5120-242-3263 GGG-W-686
36- (d) O PLIERS 5120-464-4777 11578314
37 - (d) (g) F HOLDER PLANET CARRIER 4933-915-8558 11576798
38 - (d) (g) F WRENCH ASSEMBLY 4933-915-8540 11576794
39 (d) (g) F WRENCH ASSEMBLY 4933-915-8559 11576784
40 - (d) (g) O WRENCH ASSEMBLY 4933-915-8560 11576797
41 - (g) (h) F UNLOCKING TOOL 4933-915-8531 11576774
42 -(g) (h) F WRENCH 4933-930-1843 11577250
43 - (g) (h) O WRENCH 4933-111-6734 11578063o
44 - (c) O PULLER TOOL 4933-117-9351 11578228
45 - (a) (g) (i) O SERVICING TOOL 4933-464-4776 11578313
C-25
C9, TM 9-2350-230-12


REFERENCE CODE
46 - (c) (h) O WRENCH SPANNER 5120-915-8572 11577226
47 - (h) F CRIMPING TOOL TERMINAL 5120-928-3801 11602938
48 - (c) F EXTRACTOR CONTACT ELECTRICAL 4933-929-0850 11602937
49 - (c) F EXTRACTOR CONTACT ELECTRICAL 4933-929-0849 11602936
50 - (c) (g) (h) (i) O PLIERS ELECTRICAL 5120-624-8065 AT508K
51 - (c) (h) O ADAPTER 5120-227-8088 GGG-IW-641
52 - (c) (h) O SOCKET, SOCKET WRENCH 5120-261-2823 MS16253-34
53 - (c) (h) O SOCKET, WRENCH ATTACHMENT 5120-683-8597 GGG-VW-641
54 - (d) (g) (h) F ADAPTER TORQUE WRENCH 5120-915-8568 10954930
55 - (c) F ADAPTER GUN 4930-765-8128 7648128
56 - (c) F ADAPTER GUN 4930-764-8129 7648129
57 - (c) F ADAPTER GUN 4930-764-8130 7548130
58 - (c) F ADAPTER GUN 4J00-7;4-8v1.] 7648131
59 - (b) D ADAPTER, VIBRATOR USED W/VIBRATOR MACHINE 1240-924-8387 for MOUNT 11732135
M149
60 - (a) D COLLIMATOR PROJECTOR 4931-757-3291 7573291
61 - (e) F FIXTURE, DOUBLE COLLIMATOR HOLDING W/CASE FOR MOUNT M149 11732248
MODIFIED
DOUBLE COLLIMATOR 4931-561-0798
62 - (f) D FIXTURE FINAL TEST 4931-929-8385 10547192
63 - (c) D FIXTURE PRESSURE TEST 4931-065-2018 8565556
64 - (c) F GUN SEALING COMPOUND HAND 4931-764-8117 7648117
65 - (c) F GUN SEALING COMPOUND HYDRAULIC 4931-764-8134 7648134
66 - (d) (e) H COLLIMATING FIXTURE W/CASE 11728553
67 - (c) O KIT PURGING 4931-065-1110 SC4931-95-CL-
J54
C-26
C9, TM 9-2350-230-12


REFERENCE CODE
68 - (b) D MACHINE, VIBRATOR 4931-00-929-8387 10547947
69 - (c) O NITROGEN TANK (CYLINDER) 6830-00-292-0131 MS56830-9
70 - (d) F RADIOMETER TEST SET W/CASE 11730875
71 - (c) C SCREWDRIVER 5120-00-809-1570 GGG-S-121
72 - (g) (h) F WRENCH SET, SPANNER 5120-00-580-0012 SC 4931-95-CL1
J52
73 - (d) D ADAPTER TORQUE 4931-00-045-4363 10549921
74 - (d) (Deleted)
77 - (d) D DIOPTOMETER 4931-00-536-5557 7680631
78 - (h) F FIXTURE ASSEMBLY 4931-00-493-9233 11727601
79 - (f) (Deleted)
80 - (e) F GAGE SPACER 4931-00-947-3059 8566948
81 - (d) D HOLDER TELESCOPE 4931-00-612-1110 6121110
82 - (a) D TEST SET, FINAL, PERISCOPE 4931-00-156-9920 A. O. 7150
83 - (b) F TEST SET, PERISCOPE 4931-00-184-9878 11727677
84 - (b) (Deleted)
85 - (b) D ADAPTER VIBRATION 4931-00-466-2003 10549681
86 - (d) D COLLIMATOR TELESCOPE 4931-00-554-9108 5549108’
87 - (d) D ADAPTER 4931-00-909-3144 8566741
88 - (a) D FIXTURE FINAL INSPECTION 4931-00-868-8402 10527436
89 - (b) D POWER SUPPLY 4931-00-536-5556 7561204
C-27
C9, TM 9-2350-230-12


REFERENCE CODE
90 - (b) D ADAPTER, TUBE TESTER 4931-00-053-3644 8566309
91 - (d) D TRANSFOR.MER POU’ER SUPPLY 5950-00-243-4136 7284975
92 - (g) (h) D U’RENCH SPANNER 5120-00-561-0854 8284044
93 - (b) D ADAPTER VIBRATION 4931-00-027-2596 10549922
94 - (a) D FIXTURE FINAL INSPECTION 4931-00-929-8383 8570164
95 - (g) F WRENCH SPANNER 5120-00-595-8996 7597708
96 - (g) (1)) O SOCKET WRENCH ATTACHMENT 5120-00-596-0934 GGG-W-641
97 - (,) (h) O SOCKET WRENCH ATTACH.MENT SOCKET HEAD SCREW 5120-00-596-8508 GGG-W-641
98-(b)(d) O TEST SET, TURRET ELECTRICAL, FAULT ISOLATION 4933-00-432-7269 11678960
C-28
C9, TM 9-2350230-12
INDEX
NOTE. This Index has been revised in its entirety.
PAGE NO. PAGE NO.

Oper. Org. Oper. Org.
Crew Maint. Crew Maint.
A B
Accelerator/Throttle Ballistic Shield

Control ...................................... 2-8 9-42 (Commander’s)......................... 2-32.2 10-36.2
Access Doors, Battery Basic-Issue (OEM) Items ....................... B-1
and Air Cleaner ........................ 5-10 9-125 Batteries, Vehicle
Access Plugs, Hull. ................................. 5-18 Access Door ............................. 5-10 9-146.2
Accessory Box, Turret Service and Maintenance ........ 5-12 9-90
Control ...................................... 10-3 Battery, XM44 Series
Accessory Outlet Periscope ................................. 5-22.1
Receptacle ............................... 2-10 Belt Tensioner, "V" ................................. 5-9 9-90
................................................. 2-15 Bilge Pumps ........................................... 2-20.1 9-125
Accumulator, Air Box Blasting Machine (Impulse
Flame Heater............................ 2-21 9-13 Generator)................................ 3-7 10-17
Accumulator Pressure Boresighting. .......................................... 2-35
Gage......................................... 2-21 9-13 Brakes, Parking and
Adhesives, Application............................ 8-1 Service .................................... 2-10 9-42
Adjuster, Track Break-In-Services ................................... 2-6
Hydraulic .................................. 5-13 9-66 Breather Drain Collector,
Air Box Heater and Engine .................................... 9-13
Components. ............................ 9-13 Breech Assembly and
Air Cleaner, Engine................................. 5-9 9-13 Components ............................. 3-5 11-1
Air Delivery (Preparation) ....................... 6-1 Breech Electric Drive
Air Filter Unit (M8A3) .............................. 2-24 10-29 Motor ........................................ 11-1
Air Pressure Gage (CBS) . ..................... 3-8. 4 10-20.1 Breech Electric Drive
Ammunition Solenoid . ................................. 11-1
Missile ...................................... 7-1 Brush, Elevating and
Conventional ............................ 7-4.1 Traverse Mechanism................ 10-3
Ammunition and Missile Buffer, Counterrecoil .............................. 5-23 11-1
Stowage Racks: Bulkhead Access Panel .......................... 4-13
Hull ........................................... 3-9 9-125 C
Turret ........................................ 3-9 10-36.2 Cable Assembly, Missile
Ammunition Feed System, Subsystem ............................... 10-20.4
Machine Gun, 7. 62MM . ......... 3-12 10-36.2 Cables, Control....................................... 9-65
Amphibious Operation ............................ 2-15 Carrier Cover Vent Plug ........................ 11-1
Amplifier Integrator Check Valve (CBS)................................. 11-1
Assembly .................................. 10-3 Checkout Panel, Missile
Anchor, Torsion Bar ................................ 9-66 Subsystem.............................................. 2-48 10-20.4
Antenna, Radio (Front Circuit Breaker, Hull ............................... 9-90
and Rear) ................................. 7-6 10-29 Circuit Cutout Box................................... 10-29
Antifreeze................................................ 1-2 9-14 Closed Breech Scavenging
Armament Maintenance.......................... 5-23 11-1 System:
................................................. 11-25 Description .............................. 3-4
Auxiliary Power (Slave) Operation ............................... 3-8.3
Receptacle .............................. 2-10 9- 90 Maintenance and Service......... 4-8 8-85
Azimuth Indicator: ................................................. 11-10.2
Data .......................................... 1-3 ................................................. 11-10.4
Operation.................................. 2-43 Commander’s Ballistic
Maintenance ............................. 2-44 11-32 Shield ....................................... 2-32.2 10-36.2
Commander’s Control
Handle...................................... 2-32.1 10-3
Index-1
C9, TM9-2350-230-12
PAGE NO.
C - Continued
D - Continued
Communications Equipment ................... 7-5.
Compressor (CBS) ................................. 3-8.3 10-18.2 Driver’s Switch Panel.............................. 2-15 9-90
Contact Ring, Turret Driving ................................................. 2-7
Electrical .................................. 10-29 Driving Lights:
Contamination Shield, Operation .......... ...................... 2-13
Radiator ................................... 9-125 Maintenance ............................ 5-15 9-90
Control Assembly, Cupola ...................... 2-33 10-29 Dust Shield .......... .................... 11-1
Control Box Assembly E
Personnel Heater ..................... 2-27 9-90 Electrical Cable Terminals
Control Box, Cupola................................ 2-33 10-29 and Connectors ........................ 9-91
Control Box, Loader’s ............................. 3-5 10-17 Electrical Maintenance
Control Cables ....................................... 9-65 Hull and Power Plant................ 9-90
Control Handles Turret and Cupola .................... 10-1
Commander’s ........................... 2-32.1 10-3 Electrical Plug and
Gunner’s ............ ...................... 2-31 10-3 Receptacle. . ............................ 9-91
Conventional Weapons Relay Elevating Mechanism ............................ 2-29 10-3
Box ........................................... 10-17 Elevation and Depression
Cooling System (Engine) ........................ 5-9 9-13 Bump Stops ............................. 10-3
Cupola Operation.................................... 2-33 Elevation Quadrant,
Cupola Operation, Manual ...................... 2-35 M13AIC:
D Operation ................................ 2-43
Data, Tabulated ...................................... 1-1 Maintenance ............................ 2-45 11-32
Debris Screens ....................................... 9-125 Engine and Components
Depression Control, Gun- Data ......................................... 1-2
Launcher .................................. 10-3 Replacement .................... ........ 9-2
Deprocessing Vehicle ............................ 2-1 Maintenance............................. 5-9 9-13
Description of Vehicle ............................. 1-1 Mount Assembly....................... 9-13
Photographs, Overall ................ 1-4 Evacuator (Bore) .................................... 5-22.2 11-1
Destruction of Materiel ............................ 6-4 Exhaust System, Engine ........................ 9-13
Detent and Trigger Lever, F
Ammunition .............................. 3-7 11-1 Fan Lockup............................................. 5-11
Dimmer Switch, Driving ................................................. 2-14
Lights ....................................... 2-13 9-90 Filters;
Dipstick Fuel (Engine) .......................................... 5-9 9-13
Engine ..................................... 5-11 Oil (Engine) ........ ..................... 9-13
Transmission .......................................... 5-11 9-42 Fuel Tank Filler ........................ 9-13
Compressor ............................................ 3-2.4 10-18.2 Personnel Heater Fuel.. ........... 9-125
Dome Lights ........................................... 2-10 9-90 Recoil Mechanism
Door, Transmitter Cover Reservoir.................................. 11-9
Operation.................................. 2-48.1 Transmission Oil ..................... 9-42
Maintenance ............................ 5-21 10-20. 4 Fire Control Operation ............................ 2-35
Drain Plugs, Power Plant ........................ 5-18 Firing Probe Assembly ........................... 11-1
Draining Checking Continuity ................. 4-11
Fuel System ............................. 5-17 Firing Procedures .................................. 3-1
Coolant System ........................ 5-17 Fire Extinguisher
Drive Control, Turret Fixed ........................................ 2-10 9-125
Electrical ................................... 2-29 10-3 Portable ........... ........................ 2-28
Driver’s Controls ..................................... 2-10 Flotation Skin Repair .............................. 9-125
Driver’s Indicator Panel........................... 2-14 9-90
Index-2
C9,TM 9-2350-230-12
PAGE NO. PAGE NO.

F - Continued I - Continued
Forms, Records and Idler Hub Assembly ................................ 9-66
Reports......... ............................ 1-1 Idler Wheels, Track ..... .......................... 9-66
Fuel Data .......... ..................................... 1-2 Igniter, Personnel
Fuel Filter Inspection .... ......................... 2-3 Heater ...................................... 9-125
Fuel Level Transmitter ............................ 9-91 Indicator Panel, Driver’s:
Fuel Pump, Personnel Operation ................................ 2-14
Heater ................................................. 9-125 Maintenance ............................ 5-15 9-90
Fuel Shut-off Controls. ............................ 2-10 9-13 Indicator, Safe to Fire ............................ 3-8
Fuel System, Engine............................... 5-9 9-13 Intercom Box Door
G Assembly, Ground.................... 7-8 9-147
Generator and Drive Intercommunication
Assembly .................................. 9-90 Equipment ................................ 7-5
Generator Voltage L
Regulator ........ ......................... 9-90 Lamps, Spare:
Grenade Launcher, M176 ....................... 3-24 11-25 Hull ........................................... 5-15
Grenade Launcher Guard Turret ....................................... 5-19
Kit ............................................. 12-2 Basic Issue .................. B-4
Ground Intercom Access Land Steer Control Cable
Door.......................................... 7-8 9-147 and Linkage.............................. 9-42
Gun and Turret Control Less-Missile Kit ...................................... 12-2
Selector .................................... 2-42.2 Loading, Firing and
Gun-Launcher and Unloading:
Components: 152MM Gun-Launcher ............ 3-4
Data ......................................... 1-2 Cal.. 50 Machine Gun ............. 3-14
Operation ................................. 3-5 7. 62MM Machine Gun ............ 3-10.2
Maintenance ............................ 5-23 11-1 M176 Grenade Launcher. ....... 3-24
Gun-Launcher Tube................................ 11-1 Loading Tray Bracket
Gunner’s Controls and Assembly.................................. 11-1
Instruments .............................. 2-31 Loading Tray and Ejector ....................... 3-7 11-1
Gunner’s Control Handle ........................ 2-31 10-3 Lubrication Order ................................... D-1 D-1
Gunner’s Leg Guard..... .......................... 10-36.2
Gyro Selector Assembly M
Electric Drive ............................ 10-3
Machine Gun, Cal.. 50, M2:
H Data.......................................... 1-3
Operation ................................ 3-14
Hatch Cover, Loader’s ............................ 2-32 10-36.2 Maintenance............................. 5-23 11-25
Hatch, Driver’s Escape .......................... 2-11 9-125 Machine Gun, 7. 62MM, M73:
Hatch, Driver’s Data.......................................... 1-3
Rotatable: Alignment ................................ 2-40
Operation.................................. 2-10 Operation ................................ 3-10. 2
Maintenance ............................. 9-125 Maintenance ............................ 5-23 11-25
Headlights: Machine Gun, M73E1 -
Operation.................................. 2-13 Redesignated M219
Maintenance ............................ 5-15 9-90 Machine Gun, 7. 62MM, M219:
I Data ....................................... 13-1
Idler Housing and Spindle Alignment ......................... ........ 2-40
Assembly .................................. 9-66 Operation ................................. 3-10. 2
Maintenance ........................... 13-1
Index-3
C9,TM 9-2350-230-12
PAGE NO. PAGE NO.

M - Continued O - Continued
Maintenance ......... ................................. 8-1 Oddment Stowage Box........................... 10-36.2

Hull and Suspension. ............... 5-9 9-1 Oil Cooler Cores
Turret and Cupola..................... 5-19 10-1 ...... Engine and Transmission . 9-13
10-3 Oil Level Indicator
10-17 Engine ..................................... 5-11
10-20.4 Transmission ........................... 5-11 9-42
10-29 Compressor.............................. 3-2.4 10-18.2
10-36.2 Operation
Armament ................................. 5-23 11-1 152MM Gun-Launcher ............. 3-4
11-25 Cal.. 50 Machine Gun ............. .3-14
Sighting and Fire Control. 11-32 7. 62MM Machine Gun ............ 3-10.2
Maintenance Allocation M176 Grenade Launcher ......... 3-24
Chart ........................................ C-1 C-1 Optical Tracker ....................................... 2-48 10-20.4
Maintenance, Preventive . ...................... 4-1 8-75 Optical Transmitter Cover
Master Relay .......................................... 9-90 and Door .......... ....................... 2-51 10-20.4
Mine Protective Kit..... ............................. 12-2
Misfire, Hangfire, and P
Cookoff....... .............................. 3-1
Missile, Guided: Painting and Stenciling ... ...................... . 8-1
Identification ...... ...................... 7-4 Panel
Inspection ....... ........................ 7-4 Grenade Launcher
Service Upon Receipt Control...................................... 3-29 10-29
of Materiel ................................ 7-2 Driving Light Switch.................. 2-13
Missile Inspection Points ........................ 7-3 Indicator, Driver’s ..................... 2-14 9-90
Missile Subsystem: Switch. Driver’s........................ 2-15 9-90
Data .......... ............................... 1-3 Test Checkout ....... .................. 2-52 10-20.4
Operation ................................. 2-48 XM44 Series Periscope
Maintenance ............................. 5-19 10-20.4 Control...................................... 2-42 2 11-32
Modulator ........... .................................... 2-48 10-20.4 Periscope, Driver’s M47
Motor-Generator ..................................... 10-3 Data ......................................... 1-3
Mount and Components, Operation ........ ........................ 2-10
Gun-Launcher ......................... 5-23 11-1 Maintenance ............................ 5-19 11-32
Mount, 7. 62MM Machine Periscope, Driver’s M48
Gun Data ......................................... 1-3
Alignment ................................. 2-40 Operation ................................. 2-12
Maintenance ............................. 11-1 Maintenance............................. 11-32
Mount, Driver’s Periscope Periscope, Gunner’s
M47 and ................................... 11-32 XM44 Series
Mount, Loader’s Periscope Data.......................................... 1-3
M37 .......................................... 11-32 Operation ................................. 2-36
Mount, Gunner’s Telescope Maintenance............................. 11-32
M149......................................... 11-32 Periscope - Loader’s, M37...................... 2-32 11-32
Periscope Washers ................................ 2-12 11-32
N Personnel Heater: ........................ 2-27 9-125
Pintle Support ......................................... 10-36.2
Neutral Safety Switch ............................. 9-42 Platform, Commander’s .......................... 2-32 10-36.2
................................................. 9-90 Power Plant
Night Vision Sight ................................... 2-46 Data ......................................... 1-2
Maintenance ............................ 5-9 9-1
0 Replacement ........ ................... 9-2
Power Supply, Grenade
Obturator Seal ........................................ 5-24 11-1 Launcher ................. 10-29
Index-4
Index-4
C9, TM 9-2350-230-12
PAGE NO. PAGE NO.

P - Continued R -Continued.
Power Supply, Missile Reticle Dimmer Box ................................ 2-41

Subsystem .............................................. 10-20.4 2-42
Power Supply, 120V Firing Road Wheels .......................................... 9-66
Circuit ....................................... 10-17 Road Wheel Arms .................................. 9-66
Power Supply, Turret Road Wheel Arm Housing ...................... 9-66
Control ...................................... 2-51 10-3 Road Wheel Arm Spindle ....................... 9-66
Preventive -Maintenance
Services.................................... 4-1 8-75 S
Prevailing Torque.................................... 11-1
Protective Pad-Gunner’s Safety Precautions ................................. 1-6
Leg guard ................................. 10-36.2 Scavenger System (CBS)....................... 3-8. 3 11-1
Pump: Seal, Driver’s Hatch................................ 9-125
Accumulator, Air Box Searchlight Kit
Heater....................................... 2-21 9-13 Installation ................................ 2-57
Bilge ......................................... 2-20.1 9-125 Operation ................................. 2-59
Coolant, Engine ........................ 9-13 Seat Commander’s................................. 2-32 10-36.2
Fuel, Engine ............................. 9-13 Seat, Driver’s .......................................... 2-10 9-125
Fuel Tank Condensa- Seat, Gunner’s........................................ 2-32 10-36.2
tion Drain .................................. 5-12 9-23 Seat, Loader’s ........................................ 2-32 10-36.2
Heater, Personnel ................... 9-125 Servo Motors, Elevating
Recoil Mechanism, and Traversing ......................... 10-3
Gun-Launcher .......................... 3-8 11-1 Shock Absorber ...................................... 9-66
XM44/Series Periscope Signal Data Converter ............................ 2-51 10-20.4
Washer ..................................... 2-42.2 11-32 Special Tools and
M47/48 Periscope Equipment ................................ B-8 8-1
Washer ..................................... 2-12 11-32 ................................................. C-24 C-24
Q Special Tools, Suspension ..................... 9-66
Quadrant, M1A1 and Speedometer Drive................................. 9-91
M13AC...................................... 2-45 11-32 Spent Brass Chute and Bag,
R 7. 62MM Machine Gun ............ 3-13 11-1
Radiator Cleaning Kit .............................. 4-12 10-18.1 Spindle, Road Wheel Arm ...................... 9-66
Radiator, Engine Coolant........................ 9-13 Sprocket Drive Shaft............................... 9-66
Radio Sets AN/VRC Sprocket Hub and Support ..................... 9-66
(Basic Units) ............................. 7-5 Sprocket and Sprocket
Rate Sensor............................................ 2-51 10-20.4 Carrier Wheels ......................... 9-66
Recoil Mechanism, Gun- Starter, Engine ....................................... 9-90
Launcher, 152MM: Starting
Guard and Screen ................... 11-1 Normal...................................... 2-7
Hydraulic Fittings ...................... 11-1 Cold Feather ............................ 2-20.2
Hydraulic Hand Pump............... 3-8 11-1 With Auxiliary Power ............... 2-22
Reservoir .................................. 3-8 11-1 By Towing................................. 2-22
Adjustment ............................... 3-8 Steer Controls and Linkage .................... 9-42
Regulator, Voltage .................................. 9-90 Storage ................................................. 6-3
Relays Stowage ................................................. B-4 9-125
Bilge Pump ............................... 9-90 ................................................. 10-36.2
Master....................................... 9-90 Surfboard and Barrier ............................. 2-18 9-125
Starter. ..................................... 9-90 Surge Tank ............................................. 5-11 9-13
Relay Box, Weapons .............................. 10-17 Switches:
Azimuth Indicator ..................... 11-32
Engine Pressure....................... 9-90
Engine Temperature ................ 9-90
INDEX-5
C9,TM 9-2350-230-12
PAGE NO. PAGE NO.

S - Continued T - Continued
Switches:- Continued Transmission - Continued

Gun-Launcher Breech Shift Control ............................. 2-10 9-42
Limit .......................................... 11-1 Controls and Linkage ............... 9-42
In-Battery .................................. 11-1 Internal Brake ........................... 9-42
Neutral Safety........................... 9-90 Oil Filter.................................... 9-42
Personnel Heater Flame Oil Level Indicator ................... 5-11 9-42
Detector .................................... 9-141 Transmitter, Optical ................................ 2-51 10-20.4
Safe-To-Fire Indicator............... 10-17 1 Traverse Lock, Turret ............................. 2-32 10-36.2
Transmission Pressure ............. 9-90 Traverse Mechanism,
Transmission Tem- Cupola...................................... 2-33
perature ................................... 9-90 Traversing Mechanism,
Transmitter Cover Turret ................................................. 2-29 10-3
Door.......................................... 10-20 Troubleshooting...................................... 5-1 8-8
Water Steer .............................. 9-90 Electrical................................... 8-45
Turret Floor Access
T Cover........................................ 4-10 10-36.2
Turret Operation ..................................... 2-29
Tachometer Drive ................................... 9-91 Turret Stowage
Taillights ......................................... 5-15 9-90 Exterior..................................... 10-36.2
Telescope, M119, M127 Interior ...................................... 10-36.2
Data .......................................... 1-3
Operation.................................. 2-36 V
Maintenance ............................ 5-19 11-32
Telescope Shield .................................... 10-36.2 Valve, Fuel Tank Shut-Off ..................... 5-12 9-13
Tensioner, "V" Belt.................................. 5-11 9-90 Vehicle Operation .................................. 2-7
Terminals and Connectors...................... 9-91 Vent Plug, Carrier Cover ........................ 11-1
Test Checkout Panel .............................. 2-52 Ventilating Fan, Turret . ......................... 2-32 10-29
Test Set, Electric Drive Vision Blocks, Cupola. ........................... 2-34 10-36.2
Control ..................................... 10-3 Voltage Regulator. ................................. 9-90
Throttle/Accelerator
Controls .................................... 9-42 W
Tools
Basic Issue ............................... B-5 Washer, Periscope ................................. 2-12 11-32
Special ..................................... B-8 8-1 Water Steer ............................................ 2-10 9-42
................................................. C-24 C-24 Winterization Kit
Improvised ................................ 8-1 Operation ................................. 2-53
Pioneer .................................... B-7 Troubleshooting ....................... 8-28
Torque, Prevailing................................... 11-1 Electrical
Torsion Bars and Road Troubleshooting ....................... 8-66
Wheel Arms .............................. 9-66 Maintenance............................. 12-1
Tow Bar or Tow Cables .......................... 2-23
Towing ................................................. 2-22
Track ................................................. 5-13 9-66
................................................. 5-14
Tracker, Optical ...................................... 2-51 10-20.4
Transmission
Data .......................................... 1-2
Oil Pressure Check
Points ....................................... 8-9
Tests......................................... 8-10
Replacement ............................ 9-2
Index-6
By Order of the Secretary of the Army:
HAROLD K. JOHNSON,
General, United States Army,
Chief of Staff
Official:.
J. C. LAMBERT,
Major General, United States Army,
The Adjutant General.
Distribution:
To be distributed in accordance with DA Form 12-37 requirements for Organizational ’enauce, Armored
Reconnaissance Airborne Assault Vehicle 152-mm, XM551.
*U.S. GOVERNMENT PRINTING OFFICE : 1986 0-491-421/40007

PIN:PIN:
028650-014
028650-000

TM 9-2350-230-12 - Armored Reconnaissance/Airborne Assault Vehicle M551 Sheridan

Uploaded by

Document Informationclick to expand document informationTM 9-2350-230-12 - OPERATOR AND ORGANIZATIONAL MAINTENANCE MANUAL ARMORED RECONNAISSANCE/AIRBORNE ASSAULT VEHICLE FULL-TRACKED, 152-MM, M551

Document Informationclick to expand document information

Copyright:

Available Formats

TM 9-2350-230-12 - Armored Reconnaissance/Airborne Assault Vehicle M551 Sheridan

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TM 9-2350-230-12 - Armored Reconnaissance/Airborne Assault Vehicle M551 Sheridan

Uploaded by

Copyright:

Available Formats

DEPARTMENT OF THE ARMY TECHNICAL MANUAL

OPERATOR AND ORGANIZATIONAL

FULL-TRACKED, 152-MM, M551

HEADQUARTERS, DEPARTMENT OF HE ARMY

IT OCCURS IN THE EXHAUST FUMES OF FUEL-BURNING HEATERS AND

1. DO NOT OPERATE HEATER OR ENGINE OF VEHICLE IN AN ENCLOSED AREA UNLESS IT IS

THE BEST DEFENSE AGAINST CARBON MONOXIDE POISONING IS ADEQUATE VENTILATION.

FIRE OR REMOVE AMMUNITION WITHIN FIVE MINUTES OF CHAMBERING.

"Grenade projector" should read "grenade launcher" wherever it appears.

Operator and Organizational Maintenance Manual:

ARMORED RECONNAISSANCE/AIRBORNE ASSAULT VEHICLE:

TM 9-2350-230-12, 1 June 1966, is changed as follows:

3. Remove old pages and insert new pages as indicated below.

Remove pages Insert pages

vii and viii vii and viii

None 11-29 and 11-30

By Order of the Secretary of the Army:

CONVENTIONAL 152 MILLIMETER PROJECTILES ARE ASSEMBLED TO HIGHLY FLAMMABLE,

DO NOT TOUCH, MOVE OR OTHERWISE HANDLE DUDS.

NOTIFY EOD OF LOCATION.

AZIMUTH DIAL POINTERS ARE TIPPED WITH RADIOACTIVE MATERIAL.

HAZARDOUS RADIATION CONDITIONS EXIST WHEN DIAL WINDOW IS BROKEN OR REMOVED.

ALL MAINTENANCE MUST BE PERFORMED AT DEPOT LEVEL ONLY, EXCEPT FOR

PROTECTION, HANDLING, STORAGE, AND DISPOSAL OF RADIOACTIVE MATERIAL SHALL BE IN

Operator and Organizational Maintenance Manual

CHAPTER 2. OPERATING INSTRUCTIONS

Section 3-1. Misfire, Hangfire, and Cook-off, and Immediate

Section 4-1. Preventive-Maintenance Services .............................................................................4-1

CHAPTER 5. CREW MAINTENANCE

Section 5-1. Repair Parts, Tools, and Equipment..........................................................................5-1

CHAPTER 6. PREPARATION FOR AIR-DELIVERY, STORAGE AND

Section 6-1. Preparation for Air-Delivery ....................................................................................... 6-1

CHAPTER 7. MATERIEL USED IN CONJUNCTION WITH MAJOR ITEM

CHAPTER 8 ORGANIZATIONAL MAINTENANCE INSTRUCTIONS

CHAPTER 9 ORGANIZATIONAL MAINTENANCE - POWER PLANT AND HULL

Section 10-1 Turret Electrical Systems.........................................................................................10-1

Section 11-1. Primary Armament .................................................................................................. 11-1

Section 11-1 Primary Armament - Continued

CHAPTER 12 SPECIAL PURPOSE KITS

Section 12-1. General ....................................................................................................................12-1

APPENDIX I. REFERENCES ............................................................................................................... A-1

APPENDIX II. BASIC ISSUE ITEMS LIST

Section B-1. Introduction ..................................................................................................................... B-1

APPENDIX II. MAINTENANCE ALLOCATION CHART

Section 1-1. SCOPE, SECURITY CLASSIFICATION,

1-1. Scope 1-4. Forms, Records, Reports, and Equipment

Overall length ..................................... 248 in. (20ft 8 in.) Cooling system:

Fuel tank capacity (usable).................................. 158 gal Gun-Launcher, 152MM:

Breech chamber .......................... Left-hand 200 buttress Gunner’s aid dial:

Telescope, M127 (gunner’s):

Mount, Telescope, M149:

i. Missile Subsystem Units.

Optical transmitter .............................................. 34. 1 lb

1-7. Vehicle 1-8. Turret and Cupola

h. Attach tow cable to front or rear tow 1-10. Armament

m. The closed breech scavenging system has

(1) When maximum firing rate is not required,