METAL AMERICAN NATIONAL STANDARD

BAR
G R AT I N G S
GRATING
ANSI/NAAMM
STANDARD MBG 531 -15

ANSI/NAAMM MBG 531-15

METAL BAR GRATING
MANUAL
5

EIGHTH EDITION
ANSI/NAAMM MBG 531-15

Maximum Bearing Bar Depth . . . 2 1/2" (63.5 mm)

5
Maximum Bearing Bar Thickness

G R AT I N G S
Steel & Stainless Steel . . . . . . . 3/16" (4.8 mm)
Aluminum . . . . . . . . . . . . . . . . . . . 1/4" (6.4 mm)

Maximum Depth of I-Bar . . . . . . . 2 1/2" (63.5 mm)

MBG Metal Bar Grating

A Division of

NATIONAL ASSOCIATION OF
ARCHITECTURAL METAL MANUFACTURERS
ANSI/NAAMM MBG 531-15

National Association of Architectural Metal Manufacturers

800 Roosevelt Road
Bldg. C, Suite 312
Glen Ellyn, Illinois 60137
Phone: (630) 942-6591 Fax: (630) 790-3095
www.naamm.org

Copyright 1967, 1974, 1979, 1988, 1994 (Reprinted 1997), 2001, 2009, 201_
National Association of Architectural Metal Manufacturers
All Rights Reserved
 ANSI/NAAMM MBG 531-15

Eighth Edition

NAAMM MBG 531

800 Roosevelt Road

Bldg. C, Suite 312
Glen Ellyn, Illinois 60137
Phone: (630) 942-6591
www.naamm.org
email: [email protected]
ANSI/NAAMM MBG 531-15

The members of the Metal Bar Grating Division of the National Association
of Architectural Metal Manufacturers have supported the preparation of this
Manual. All are producers and/or suppliers of products conforming to the
standards and specifications contained herein. A copy of the Membership
Roster of the Metal Bar Grating Division is available from NAAMM at
www.naamm.org.
 ANSI/NAAMM MBG 531-15

FOREWORD
The NAAMM Metal Bar Grating Manual provides architects and engineers with
current technical data on bar gratings and stair treads of steel, stainless steel, and
aluminum. The information contained is based on sound engineering principles
and reflects practices recommended by leading manufacturers in the industry.
The first seven editions of the manual have been widely used by the design
professions. In preparing this eighth edition, the Metal Bar Grating Division of
NAAMM has reviewed its contents in detail and has made revisions to reflect
current practices.
The load tables in this edition are based on the design formulas and procedures
found in ANSI/NAAMM MBG 534-14 Metal Bar Grating Engineering Design Manual,
which was developed to provide a clearer understanding of the procedures used
in the design of grating and treads.
Also included are metric equivalents as an aid to designers who use the metric
system. The system of metric measurement used is from IEEE/ASTM SI 10-2010,
Standard for Use of the International System of Units (SI): The Modern Metric
System.
The stair treads shown in this standard have been tested and conform to the
requirements of OSHA 29CFR 1910.24(c), IBC 2012.
Changes from the previous edition, ANSI/NAAMM MBG 531-09 are indicated by
the placement of a vertical line next to the changed item.

Standard Marking System . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Standard Gratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Minimum Sizes and Tolerances of Bars . . . . . . . . . . . . . . . . . .7
Load Tables / Inch-Pound units
Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Aluminum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Load Tables / Sl units
Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Aluminum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Anchoring Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Installation Notes; Panel Dimensions . . . . . . . . . . . . . . . . . . .15
Installation Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Operation and Maintenance Instructions . . . . . . . . . . . . . . . .17
Standard Tread Nosings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Tread Dimensions and Details . . . . . . . . . . . . . . . . . . . . . . . . .19
Manufacturing Tolerances . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Welding Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Grating Uses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Information to be Provided when Ordering . . . . . . . . . . . . . .23
Standard Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Code of Standard Practice . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

3
ANSI/NAAMM MBG 531-15

Bearing bar spacing is designated by a number

which indicates sixteenths of an inch, or mm.
For welded or pressure-locked grating this is the
distance, in sixteenths of an inch, or mm, center-to-
center of bars.
For riveted grating it is the distance, in sixteenths of
an inch, or mm, between bearing bar faces.

Cross bar or rivet spacing is designated by a number

which indicates inches, or mm.
For welded or pressure-locked grating this is the
distance, in inches, or mm, center-to-center of cross
bars. For riveted grating it is the distance in inches,
or mm, center-to-center of rivets, measured along a
single bearing bar.

The size of bearing bars is expressed in inches of

depth and thicknesses as follows:
*Equivalent bearing bar sizes in millimeters
are obtained by a multiplication factor of 25.4

4
 ANSI/NAAMM MBG 531-15

TYPE

W-19-4 (1 x 3/16) STEEL

W-30-102 (25 x 4.8)

(25 mm x 4.8 mm)

R-18-7 (11/4 x 1/8) STAINLESS STEEL

R-29-178 (32 x 3.2)

(32 mm x 3.2 mm)

P-15-2 (11/4 x 3/16) ALUMINUM

P-24-51 (32 x 4.8)

(32 mm x 4.8 mm)

P-19-4 (11/2 I Bar) ALUMINUM

P-30-102 (38 I Bar)

(38 mm I Bar)

5
ANSI/NAAMM MBG 531-15

Type W-19-4
(W-30-102)

Type P-19-4
(P-30-102)

RIVETED*
Type R-18-7
(R-29-178)

Riveted grating is also

available with a double
crimp in the reticuline bar:

6
 ANSI/NAAMM MBG 531-15

STEEL / STAINLESS STEEL WELDED*

Bearing Bars Minimum Cross Bar Size

Thickness Depth Section Area Weight

in. (mm) in. (mm) in.2 (mm2) lb/ft (kg/m)

1/8 (3.2) 3/4 (19) thru 1 (25) .031 (20) .107 (.159)
1/8 (3.2) 11/4 (32) thru 11/2 (38) .049 (32) .167 (.248)
3/16 (4.8) 3/4 (19) thru 11/2 (38) .049 (32) .167 (.248)
3/16 (4.8) 13/4 (44) thru 21/2 (64) .062 (40) .211 (.314)

*Minimum size shown is for cross bars on 4 inch centers. When

cross bars are on 2 inch centers, the minimum size may be
reduced by 25%.

STEEL / STAINLESS STEEL / ALUMINUM PRESSURE - LOCKED

Cross bars are made in a variety of solid

and hollow shapes. They can be of any
size and configuration which will provide
structural stability under the stated design loads.

ALUMINUM RIVETED STEEL / STAINLESS STEEL RIVETED

Minimum Size of Connecting Minimum Size of Connecting
(Reticuline) Bars (Reticuline) Bars
Bearing Bar Depth Bearing Bar Depth
in. (mm) Thickness Depth in. (mm) Thickness Depth
in. (mm) in. (mm) in. (mm) in. (mm)

1 (25) 1/8 (3.2) 5/8 (16) 3/4 (19) 1/8 (3.2) 5/8 (16)

11/4 (32) thru 13/4 (44) 1/8 (3.2) 3/4 (19) 1 (25) thru 13/4 (44) 1/8 (3.2) 3/4 (19)

2 (51) thru 21/2 (64) 1/8 (3.2) 1 (25) 2 (51) thru 21/2 (64) 1/8 (3.2) 1 (25)

NOTE: The following references were used as a guide in establishing the above bearing
bar tolerances: ASTM A 1011A (1011M) Commercial Steel Type B, ASTM A 510
(A510M); ASTM B 221 (B221M), ASTM B 210 (B210M); Aluminum Association
standards and data (extruded shapes).

7
ANSI/NAAMM MBG 531-15

ASTM A 1011 CS TYPE B

F=18,000psi, E=29,000,000psi

Loads above DO NOT include the dead load of the grating.

8
 ANSI/NAAMM MBG 531-15

ASTM A 1011 CS TYPE B

F=124MPa, E=200,000MPa
Recommended max. span for 6.4mm
deflected under uniform load of 4.8kPa

Kg/m2**

Loads above DO NOT include the dead load of the grating.

9
ANSI/NAAMM MBG 531-15

LOAD TABLE FOR WELDED STAINLESS STEEL GRATING - TYPE W-19

ALLOYS 304, 316 & 304L, 316L

F=20,000psi, E=28,000,000psi

Loads above DO NOT include the dead load of the grating.

10
 ANSI/NAAMM MBG 531-15

LOAD TABLE FOR WELDED STAINLESS STEEL GRATING - TYPE W-19

ALLOYS 304, 316 & 304L, 316L

F=138MPa, E=139,000MPa
Recommended max. span for 6.4mm
deflected under uniform load of 4.8kPa

Kg/m2**

Loads above DO NOT include the dead load of the grating.

11
ANSI/NAAMM MBG 531-15

LOAD TABLE FOR ALUMINUM GRATING - TYPE P-19

F=12,000psi, E=10,000,000psi

Loads above DO NOT include the dead load of the grating.

12
 ANSI/NAAMM MBG 531-15

LOAD TABLE FOR ALUMINUM GRATING - TYPE W-19

F=83MPa, E=69,000MPa

Recommended max. span for 6.4mm

deflected under uniform load of 4.8kPa

Kg/m2**

Loads above DO NOT include the dead load of the grating.

13
ANSI/NAAMM MBG 531-15

14
 ANSI/NAAMM MBG 531-15

G E N E R A L R E Q U I R E M E N T S F O R G R AT I N G I N S TA L L AT I O N
1. Unpack grating and inspect for damage.
2. Grating shall be installed with cross bars on top.
3. Preliminarily install all grating into area per layout drawing.
4. Adjust spacing between panels to allow for proper pack out and equal spacing
between panels and between supports.
5. Verify that all grating is adequately supported. Notching bearing bars at
supports or interrupting bearing bars with cutouts shall only occur when the
system has been designed for such modification and is specified by the
design engineer and indicated on the plans.
6. Securely fasten all grating as specified for project or per NAAMM
recommendations.

Shallow banding bar shall be 1/4 in. (6.4 mm)

to 1/2 in. (13 mm) less than depth of grating to
permit drainage.
15
ANSI/NAAMM MBG 531-15
Metal shall be used for all grating supports
and provide a 1 in. (25 mm) minimum bearing
surface for depths up to 21/4 in. (57 mm), and
2 in. (51 mm) minimum bearing surface for
depth 21/2 in. (64 mm) and over, at each end
of span.

1
/4 (6) nominal
clearance between
ends of cross bars
on rectangular
grating or rivet
heads on riveted
grating.

Clearances shown are recommended, but vary in accordance

with dimensional tolerances shown on page 20.
Cutouts for circular obstructions are recommended to be at
least 2 in. (51 mm) larger in diameter than the obstruction. It is
further recommended that cutouts for all piping 4 in. (102 mm)
or less in diameter be made in the field.
As shown in the drawing below, all rec-
tangular cutouts are made to the next
bearing bar beyond the penetration with
a clearance not to exceed bearing bar
spacing.

16
 ANSI/NAAMM MBG 531-15

O P E R AT I O N A N D M A I N T E N A N C E I N S T R U C T I O N S

1. For pedestrian load rated grating design, grating is intended for

normal walking pedestrian traffic. Precautions shall be taken to
prevent wheel or other loads beyond the design load rating for the
application.
2. For other uniform or concentrated load rating applications,
precautions shall be taken to prevent loads beyond the design load
rating for the application.
3. Periodically inspect grating for damage or excessive wear, such as
corrosion, damage to the finish, deformation and excessive bearing
bar lean beyond the tolerances as noted on page 20. Repair or
replace any areas showing damage.
4. Periodically inspect grating to be sure that all grating is securely
fastend as specified for the application or as noted on page 14, if
fastening method is not specified. Replace any missing attachment
hardware and tighten any loose connections.

17
 ANSI/NAAMM MBG 531-15

18
ANSI/NAAMM MBG 531-15

carrier plate
thickness 1/8 (3 mm)
minimum

DIMENSION B & C in TREAD with carrier plate detail in. (mm)

Grating Dimension Dimension
Depth B C
3/4 (19) to 11/4 (32) 13/4 (44) 21/2 (63)
11/2 (38) to 13/4 (44) 21/4 (57) 3 (76)

For aluminum and all treads over 13/4 (44) consult with manufacturer.

19
 ANSI/NAAMM MBG 531-15

20
ANSI/NAAMM MBG 531-15

The welding standards shown here apply to those gratings and treads having
a clear opening of not less than 58 in. (16 mm) between bearing bars and those
galvanized as per Specifications, page 24. See NAAMM STANDARD MBG
533 Welding Specifications for Fabrication of Steel, Aluminum and Stainless
Steel Bar Grating for welding specifications and certification of welders.

STANDARD STAIR TREADS

( bearing bar thickness less than 1/4"(6.4mm) and bearing bar clear opening greater than or equal to 5/8" (16mm) )

1/8"(3.2) 1/8"(3.2)
carrier plate carrier angle
(127)
(127)

5'
5'

1/8"(3.2) 1" (25) at mid-span* 1/8"(3.2) 1" (25) at mid-span*

for stair treads for stair treads

3' - 0 and greater 3' - 0 and greater
(914mm) (914mm)

when carrier plates and carrier angles are used, the On treads over 9-3/4 in. (248) wide
bearing bars in the front five inches, weld end of center bar also.
the back bearing bar, and the nosing shall be welded to * Treads spanning 4 ft. (1.2m) or more shall have
the carrier plate or carrier angle as shown. welds located at the third points.

21
 ANSI/NAAMM MBG 531-15

22
ANSI/NAAMM MBG 531-15

23
 ANSI/NAAMM MBG 531-15

III. MATERIALS
a) Steel gratings:
Steel used in bearing bars, cross bars and
connecting bars of rectangular section shall have
mechanical properties equal to, or greater than the
performance of ASTM A 1011/A 1011M Commercial e) Finishes: Carbon steel gratings shall be specified
Steel (Type B) for hot rolled carbon steel sheet and unfinished, galvanized, or painted one coat of
strip. Cross bars made of wire rod shall conform to manufacturers standard paint applied in
ASTM A 510 (A 510M) for carbon steel wire rods and accordance with the manufacturers standard
coarse round wire, except that permissible tolerance practice. One coat of manufacturers standard paint
on diameter of coarse round wire shall be 0.005 in. is designed as an economical solution for many
( 0.13 mm). Combinations of these steels are applications. Gratings specified to be galvanized
permitted to be welded together. shall have their exposed surfaces zinc-coated by
the hot dip process per ASTM 123 after fabrication.
Rivets shall be of steel prescribed in ASTM A 575, Gratings and/or treads stored at the jobsite shall be
1/4 in. (6.4 mm) minimum diameter, flat head type. covered or under roof. Required covering is not the
b) Aluminum gratings: responsibility of the grating and/or tread supplier.
Bearing bars shall be either alloy 6061-T6, 6105-T5, or
alloy 6063-T6, conforming to ASTM B 221 (B 221M). Unless otherwise specified, abrasive nosings will
Cross bars and bent connecting bars shall be of alloy have the manufacturers standard finish.
6061 or 6063 conforming to ASTM B 221 (B 221M), or
alloy 3003 conforming to ASTM B 210 (B 210M). Aluminum and stainless steel gratings shall have a
mill (as fabricated) finish, unless otherwise
Rivets shall be made of aluminum wire of alloy 6053- specified.
T61 conforming to ASTM B 316/B 316M.
c) Stainless steel gratings:
Bearing bars, cross bars, and connecting bars shall
be Type 304, 304L, 316, or 316L alloy conforming to
ASTM A 666.
24
ANSI/NAAMM MBG 531-15

CODE OF STANDARD PRACTICE

The rules and practices contained in this Code were developed by the NAAMM Metal Bar
Grating Division as standard for the industry. Unless specifically stated otherwise, they
shall be considered applicable to, and a part of, all contracts relating to the purchase and
supply of metal bar gratings and/or treads.

No provisions herein contained, however, shall be construed as denying the right of any
company to set its own prices and terms of sale, or restricting any Buyer or Seller from
voiding, by mutual agreement, any part of this Code.

Quotations shall preferably be on the basis of unit price per square foot (square meter) of
grating and per tread. The quoted grating price shall be for grating furnished in rectangular
sections.

25
 ANSI/NAAMM MBG 531-15

CODE OF STANDARD PRACTICE

3.1 Construction Drawings and Specifications

The Buyer shall be expected to furnish to the Seller an electronic file of construction
drawings and specifications of current issue showing the layout of supports and floor
openings correctly dimensioned, together with the sizes and types of grating and treads
desired. Should cutouts for vertical bracing or moment connections be required for shop
fabrication, the structural steel detail drawings shall be furnished prior to the preparation
of the grating drawings.

If construction drawings and specifications are not available, the Buyer shall provide
complete information regarding all items listed in Information to be Provided as shown
on page 23 of the NAAMM Metal Bar Grating Manual.

3.2 Limit of Sellers Responsibility

In the absence of written notice to the contrary, the Buyers construction plans and
specifications will be assumed by the Seller to be correct in all details, and the Sellers
responsibility shall be limited to furnishing the products in accord with these documents.

3.3 Approval Drawings

If required by the Buyer, the Seller shall submit to the Buyer one electronic copy of detailed
drawings in outline form for the latters review. The Buyer shall return one copy marked with
his approval or desired changes. Should changes be required which involve work not called
for in the original construction plans and specifications, the Seller shall have the right to
charge extra for the engineering work required to make such changes. After all necessary
corrections and/or changes are made, the drawings shall be re-submitted to the Buyer for
his final review. The Seller shall not proceed with any shop work until drawings are approved
for fabrication.

3.4 Installation Drawings

If requested, the Seller shall furnish to the Buyer an electronic copy of all installation
drawings.

26
ANSI/NAAMM MBG 531-15

CODE OF STANDARD PRACTICE

4. GRATING MISCELLANEOUS SUPPORTS

4.1 When construction drawings are furnished to the Seller as per item 3.1, drawings shall
show and locate all main and miscellaneous structural members intended to support the
grating.
4.2 To facilitate installation, it may be required to cut the grating panels around penetrations,
equipment supports, or other obstructions common to the grating supports. Buyer shall
properly review and correct any support deficiencies when such conditions occur.
4.3 Seller will not accept any type of backcharges for support deficiencies as insufficient
support is considered an omission at time of design.

1.07

0.84

27
 ANSI/NAAMM MBG 531-15

CODE OF STANDARD PRACTICE

(0.30 m)

28
ANSI/NAAMM MBG 531-15

LOAD-CARRYING BAND

METRIC The system of metric measurement used

is from IEEE/ASTM SI 10-2010, Standard for
Use of the International System of Units (SI):
The Modern Metric System.

angular
angular

29
 ANSI/NAAMM MBG 531-15

30
ANSI/NAAMM MBG 531-15