LG Led 32le5500 PDF

Internal Use Only
North/Latin America http://aic.lgservice.com

Europe/Africa http://eic.lgservice.com
Asia/Oceania http://biz.lgservice.com
LED LCD TV
SERVICE MANUAL
CHASSIS : LJ03D
MODEL : 32LE5500 32LE5500-SA
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
/I
P OK MENU INPUT
P/NO : MFL63261812 (1004-REV00) Printed in Korea

CONTENTS
CONTENTS .............................................................................................. 2
PRODUCT SAFETY ................................................................................. 3
SPECIFICATION ....................................................................................... 6
ADJUSTMENT INSTRUCTION .............................................................. 12
EXPLODED VIEW .................................................................................. 20
SVC. SHEET ...............................................................................................
Copyright LG Electronics. Inc. All right reserved. -2- LGE Internal Use Only
Only for training and service purposes
SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Exploded View.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.
An isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC Do not use a line Isolation Transformer during this check.
power line. Use a transformer of adequate power rating as this Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor
protects the technician from accidents resulting in personal injury between a known good earth ground (Water Pipe, Conduit, etc.)
from electrical shocks. and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
It will also protect the receiver and it's components from being with 1000 ohms/volt or more sensitivity.
damaged by accidental shorts of the circuitry that may be Reverse plug the AC cord into the AC outlet and repeat AC voltage
inadvertently introduced during the service operation. measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
If any fuse (or Fusible Resistor) in this TV receiver is blown, 0.5 mA.
replace it with the specified. In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
When replacing a high wattage resistor (Oxide Metal Film Resistor, repaired before it is returned to the customer.
over 1 W), keep the resistor 10 mm away from PCB.
Leakage Current Hot Check circuit
Keep wires away from high voltage or high temperature parts.
Before returning the receiver to the customer, AC Volt-meter
always perform an AC leakage current check on the exposed

metallic parts of the cabinet, such as antennas, terminals, etc., to
be sure the set is safe to operate without damage of electrical Good Earth Ground
shock. such as WATER PIPE,
To Instruments CONDUIT etc.
0.15 uF
Leakage Current Cold Check(Antenna Cold Check) exposed
With the instrument AC plug removed from AC source, connect an METALLIC PARTS
electrical jumper across the two AC plug prongs. Place the AC
switch in the on position, connect one lead of ohm-meter to the AC 1.5 Kohm/10W
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
jacks, etc. When 25A is impressed between Earth and 2nd Ground
If the exposed metallic part has a return path to the chassis, the for 1 second, Resistance must be less than 0.1
measured resistance should be between 1 M and 5.2 M.
*Base on Adjustment standard
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service 2. After removing an electrical assembly equipped with ES
manual and its supplements and addenda, read and follow the devices, place the assembly on a conductive surface such as
SAFETY PRECAUTIONS on page 3 of this publication. aluminum foil, to prevent electrostatic charge buildup or
NOTE: If unforeseen circumstances create conflict between the exposure of the assembly.
following servicing precautions and any of the safety precautions on 3. Use only a grounded-tip soldering iron to solder or unsolder ES
page 3 of this publication, always follow the safety precautions. devices.
Remember: Safety First. 4. Use only an anti-static type solder removal device. Some solder
removal devices not classified as "anti-static" can generate
General Servicing Precautions electrical charges sufficient to damage ES devices.
1. Always unplug the receiver AC power cord from the AC power 5. Do not use freon-propelled chemicals. These can generate
source before; electrical charges sufficient to damage ES devices.
a. Removing or reinstalling any component, circuit board 6. Do not remove a replacement ES device from its protective
module or any other receiver assembly. package until immediately before you are ready to install it.
b. Disconnecting or reconnecting any receiver electrical plug or (Most replacement ES devices are packaged with leads
other electrical connection. electrically shorted together by conductive foam, aluminum foil
c. Connecting a test substitute in parallel with an electrolytic or comparable conductive material).
capacitor in the receiver. 7. Immediately before removing the protective material from the
CAUTION: A wrong part substitution or incorrect polarity leads of a replacement ES device, touch the protective material
installation of electrolytic capacitors may result in an to the chassis or circuit assembly into which the device will be
explosion hazard. installed.
CAUTION: Be sure no power is applied to the chassis or circuit,
2. Test high voltage only by measuring it with an appropriate high and observe all other safety precautions.
voltage meter or other voltage measuring device (DVM, 8. Minimize bodily motions when handling unpackaged
FETVOM, etc) equipped with a suitable high voltage probe. replacement ES devices. (Otherwise harmless motion such as
Do not test high voltage by "drawing an arc". the brushing together of your clothes fabric or the lifting of your
3. Do not spray chemicals on or near this receiver or any of its foot from a carpeted floor can generate static electricity
assemblies. sufficient to damage an ES device.)
4. Unless specified otherwise in this service manual, clean
electrical contacts only by applying the following mixture to the General Soldering Guidelines
contacts with a pipe cleaner, cotton-tipped stick or comparable 1. Use a grounded-tip, low-wattage soldering iron and appropriate
non-abrasive applicator; 10 % (by volume) Acetone and 90 % tip size and shape that will maintain tip temperature within the
(by volume) isopropyl alcohol (90 % - 99 % strength) range or 500 F to 600 F.
CAUTION: This is a flammable mixture. 2. Use an appropriate gauge of RMA resin-core solder composed
Unless specified otherwise in this service manual, lubrication of of 60 parts tin/40 parts lead.
contacts in not required. 3. Keep the soldering iron tip clean and well tinned.
5. Do not defeat any plug/socket B+ voltage interlocks with which 4. Thoroughly clean the surfaces to be soldered. Use a mall wire-
receivers covered by this service manual might be equipped. bristle (0.5 inch, or 1.25 cm) brush with a metal handle.
6. Do not apply AC power to this instrument and/or any of its Do not use freon-propelled spray-on cleaners.
electrical assemblies unless all solid-state device heat sinks are 5. Use the following unsoldering technique
correctly installed. a. Allow the soldering iron tip to reach normal temperature.
7. Always connect the test receiver ground lead to the receiver (500 F to 600 F)
chassis ground before connecting the test receiver positive b. Heat the component lead until the solder melts.
lead. c. Quickly draw the melted solder with an anti-static, suction-
Always remove the test receiver ground lead last. type solder removal device or with solder braid.
8. Use with this receiver only the test fixtures specified in this CAUTION: Work quickly to avoid overheating the circuit
service manual. board printed foil.
CAUTION: Do not connect the test fixture ground strap to any 6. Use the following soldering technique.
heat sink in this receiver. a. Allow the soldering iron tip to reach a normal temperature
(500 F to 600 F)
Electrostatically Sensitive (ES) Devices b. First, hold the soldering iron tip and solder the strand against
Some semiconductor (solid-state) devices can be damaged easily the component lead until the solder melts.
by static electricity. Such components commonly are called c. Quickly move the soldering iron tip to the junction of the
Electrostatically Sensitive (ES) Devices. Examples of typical ES component lead and the printed circuit foil, and hold it there
devices are integrated circuits and some field-effect transistors and only until the solder flows onto and around both the
semiconductor "chip" components. The following techniques component lead and the foil.
should be used to help reduce the incidence of component CAUTION: Work quickly to avoid overheating the circuit
damage caused by static by static electricity. board printed foil.
1. Immediately before handling any semiconductor component or d. Closely inspect the solder area and remove any excess or
semiconductor-equipped assembly, drain off any electrostatic splashed solder with a small wire-bristle brush.
charge on your body by touching a known earth ground.
Alternatively, obtain and wear a commercially available
discharging wrist strap device, which should be removed to
prevent potential shock reasons prior to applying power to the
unit under test.
IC Remove/Replacement Circuit Board Foil Repair
Some chassis circuit boards have slotted holes (oblong) through Excessive heat applied to the copper foil of any printed circuit
which the IC leads are inserted and then bent flat against the board will weaken the adhesive that bonds the foil to the circuit
circuit foil. When holes are the slotted type, the following technique board causing the foil to separate from or "lift-off" the board. The
should be used to remove and replace the IC. When working with following guidelines and procedures should be followed whenever
boards using the familiar round hole, use the standard technique this condition is encountered.
as outlined in paragraphs 5 and 6 above.
At IC Connections
Removal To repair a defective copper pattern at IC connections use the
1. Desolder and straighten each IC lead in one operation by gently following procedure to install a jumper wire on the copper pattern
prying up on the lead with the soldering iron tip as the solder side of the circuit board. (Use this technique only on IC
melts. connections).
2. Draw away the melted solder with an anti-static suction-type
solder removal device (or with solder braid) before removing the 1. Carefully remove the damaged copper pattern with a sharp
IC. knife. (Remove only as much copper as absolutely necessary).
Replacement 2. carefully scratch away the solder resist and acrylic coating (if
1. Carefully insert the replacement IC in the circuit board. used) from the end of the remaining copper pattern.
2. Carefully bend each IC lead against the circuit foil pad and 3. Bend a small "U" in one end of a small gauge jumper wire and
solder it. carefully crimp it around the IC pin. Solder the IC connection.
3. Clean the soldered areas with a small wire-bristle brush. 4. Route the jumper wire along the path of the out-away copper
(It is not necessary to reapply acrylic coating to the areas). pattern and let it overlap the previously scraped end of the good
copper pattern. Solder the overlapped area and clip off any
"Small-Signal" Discrete Transistor excess jumper wire.
Removal/Replacement
1. Remove the defective transistor by clipping its leads as close as At Other Connections
possible to the component body. Use the following technique to repair the defective copper pattern
2. Bend into a "U" shape the end of each of three leads remaining at connections other than IC Pins. This technique involves the
on the circuit board. installation of a jumper wire on the component side of the circuit
3. Bend into a "U" shape the replacement transistor leads. board.
4. Connect the replacement transistor leads to the corresponding
leads extending from the circuit board and crimp the "U" with 1. Remove the defective copper pattern with a sharp knife.
long nose pliers to insure metal to metal contact then solder Remove at least 1/4 inch of copper, to ensure that a hazardous
each connection. condition will not exist if the jumper wire opens.
2. Trace along the copper pattern from both sides of the pattern
Power Output, Transistor Device break and locate the nearest component that is directly
Removal/Replacement connected to the affected copper pattern.
1. Heat and remove all solder from around the transistor leads. 3. Connect insulated 20-gauge jumper wire from the lead of the
2. Remove the heat sink mounting screw (if so equipped). nearest component on one side of the pattern break to the lead
3. Carefully remove the transistor from the heat sink of the circuit of the nearest component on the other side.
board. Carefully crimp and solder the connections.
4. Insert new transistor in the circuit board. CAUTION: Be sure the insulated jumper wire is dressed so the
5. Solder each transistor lead, and clip off excess lead. it does not touch components or sharp edges.
6. Replace heat sink.
Diode Removal/Replacement
1. Remove defective diode by clipping its leads as close as
possible to diode body.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.
Fuse and Conventional Resistor
Removal/Replacement
1. Clip each fuse or resistor lead at top of the circuit board hollow
stake.
2. Securely crimp the leads of replacement component around
notch at stake top.
3. Solder the connections.
CAUTION: Maintain original spacing between the replaced
component and adjacent components and the circuit board to
prevent excessive component temperatures.
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
1. Application range
This specification is applied to the LCD TV used LJ03B/D/E/F chassis.
2. Requirement for Test

Each part is tested as below without special appointment.
1) Temperature
: 25 C 5 C (77 F 9 F), CST : 40 C 5 C
2) Relative Humidity : 65 % 10 %
3) Power Voltage
: Standard input voltage (AC 100-240 V~ 50 / 60 Hz)
* Standard Voltage of each products is marked by models.
4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with
BOM.
5) The receiver must be operated for about 20 minutes prior to the adjustment.
3. Test method
1) Performance: LGE TV test method followed
2) Demanded other specification
- Safety: CE, IEC specification
- EMC:CE, IEC
4. General Specification(TV)
No Item Specification Remark
1 Receivable System 1) SBTVD / NTSC / PAL-M / PAL-N
2 Available Channel VHF : 02 ~ 13
UHF : 14 ~ 69
DTV : 07 ~ 69
CATV : 01 ~ 135
3 Input Voltage 1) AC 100 ~ 240V 50/60Hz
4 Market Central and South AMERICA
5 Screen Size 32 inch Wide (1920 x 1080) 32LE7500,32LD650,32LE5500
42 inch Wide (1920 x 1080) 42LE7500,42LD650,42LE5500,42LE8500
47 inch Wide (1920 x 1080) 47LE7500,47LD650,47LE5500,
55 inch Wide (1920 x 1080) 55LE7500,55LD650
60 inch Wide (1920 x 1080) 60LE5500
6 Aspect Ratio 16:9
7 Tuning System FS
8 LCD Module LC320EUH-SCA4 (Vitiaz 5) 32LE7500-SA
LC420EUH-SCA2 (Vitiaz 5) 42LE7500-SA
LC470EUH-SCA2 (Vitiaz 5) 47LE7500-SA
LC550EUB-SCA2 (Vitiaz 5) 55LE7500-SA
LC320WUH-SCA1(Vitiaz 5) 32LD650-SA
LC550WUB-SCA1(Vitiaz 5) 55LD650-SA
LC320EUH-SCA1(Vitiaz 5) 32LE5500-SA
Sharp 60 FHD T240 IOP LED 60LE5500-SA
LC420MUK-SCA1 (Vitiaz 5) 42LE8500-SA
9 Operating Environment Temp : 0 ~ 40 deg
Humidity : ~ 80 %
10 Storage Environment Temp : -20 ~ 60 deg
Humidity : -85 %
5. Chrominance & Luminance Specification
1) LJ03D/E (LE5500,LE7500,42LE8500)
No Item Min Typ Max Unit Remark
1. Max Luminance Module 360 450 cd/m2 32/42/47/55LE7(5)500
(Center 1-point / Full White Pattern) 450 500 42LE8500
Set 300 450 cd/m2 32/42/47/55LE7(5)500
400 500 42LE8500
2. Luminance uniformity 77 % Full white
3. Color coordinate RED X Typ. 0.651 Typ. 32LE7(5)500
-0.03 0.647 +0.03 42/55LE7(5)500
0.645 47LE7(5)500
(TBD) (42LE8500)
Y 0.332
0.332
0.333
(TBD)
GREEN X 0.308
0.309
0.310
(TBD)
Y 0.597
0.601
0.593
(TBD)
BLUE X 0.149
0.149
0.152
(TBD)
Y 0.059
0.059
0.057
(TBD)
WHITE X 0.279
(0.280)
Y 0.292
(0.290)
4. Color coordinate uniformity N/A
5. Contrast ratio 900:1 1300:1 32LE7(5)500 NORMAL
1000:1 1400:1 42/47/55, 42LE85
3,000,000:1 5,000,000:1 LE7(5)500 DCR
5,000,000:1 7,000,000:1 42LE8500
6. Color Temperature Cool 0.267 0.269 0.271 <Test Condition>
0.271 0.273 0.275 85% Full white pattern
Standard 0.283 0.285 0.287 ** The W/B Tolerance is
0.291 0.293 0.295 0.015 Adjustment
Warm 0.311 0.313 0.315
0.327 0.329 0.331
7. Color Distortion, DG 10.0 %
8. Color Distortion, DP 10.0 deg
9. Color S/N, AM/FM 43.0 dB
10. Color Killer Sensitivity -80 dBm
2) LJ03B (32/42/47/55LD650-SA)
No Item Min Typ Max Unit Remark
1. Max Luminance Module 400 500 cd/m2 32/42/47/55LD650
(Center 1-point / Full White Pattern)
Set 400 500 cd/m2 32/42/47/55LD650
2. Luminance uniformity 77 % Full white

3. Color coordinate RED X Typ. 0.642 Typ. 32LD650
-0.03 0.636 +0.03 42LD650
0.639 47LD650
(TBD) 55LD650
Y 0.334
0.335
0.334
(TBD)
GREEN X 0.292
0.291
0.290
(TBD)
Y 0.607
0.603
0.606
(TBD)
BLUE X 0.146
0.146
0.146
(TBD)
Y 0.056
0.061
0.058
(TBD)
WHITE X 0.279
Y 0.292
4. Color coordinate uniformity N/A

5. Contrast ratio 1000:1 1400:1 32LD650 NORMAL
1100:1 1500:1 42/55LD650
1200:1 1500:1 47LD650 DCR
50,000:1 70,000:1
6. Color Temperature Cool 0.267 0.269 0.271 <Test Condition>
0.271 0.273 0.275 85% Full white pattern
Standard 0.283 0.285 0.287 ** The W/B Tolerance is
0.291 0.293 0.295 0.015 Adjustment
Warm 0.311 0.313 0.315
0.327 0.329 0.331
7. Color Distortion, DG 10.0 %
8. Color Distortion, DP 10.0 deg
9. Color S/N, AM/FM 43.0 dB
10. Color Killer Sensitivity -80 dBm
6. Component Video Input (Y, CB/PB, CR/PR)
No Resolution H-freq(kHz) V-freq.(kHz) Pixel clock Proposed
1. 720*480 15.73 60 13.5135 SDTV ,DVD 480I
2. 720*480 15.73 59.94 13.5 SDTV ,DVD 480I
3. 720*480 31.50 60 27.027 SDTV 480P
4. 720*480 31.47 59.94 27.00 SDTV 480P
5. 720*576 15.625 50* 13.5 SDTV 576I
6. 720*576 31.25 50* 13.5 SDTV 576P
7. 1280*720 37.5 50* 74.25 HDTV 720P
8. 1280*720 45.00 60.00 74.25 HDTV 720P
9. 1280*720 44.96 59.94 74.176 HDTV 720P
10. 1929*1080 28.125 50* 74.25 HDTV 1080I
11. 1920*1080 33.75 60.00 74.25 HDTV 1080I
12. 1920*1080 33.72 59.94 74.176 HDTV 1080I
13. 1920*1080 56.25 50* 148.5 HDTV 1080P
14. 1920*1080 67.50 60 148.50 HDTV 1080P
15. 1920*1080 67.432 59.94 148.352 HDTV 1080P
16. 1920*1080 27.00 24.00 74.25 HDTV 1080P
17. 1920*1080 26.97 23.976 74.176 HDTV 1080P
18. 1920*1080 33.75 30.00 74.25 HDTV 1080P
19. 1920*1080 33.71 29.97 74.176 HDTV 1080P
8. RGB Input (PC)

PC DDC
1. 640*350 31.468 70.09 25.17 EGA X
2. 720*400 31.469 70.08 28.32 DOS O
3. 640*480 31.469 59.94 25.17 VESA(VGA) O
4. 800*600 37.879 60.31 40.00 VESA(SVGA) O
5. 1024*768 48.363 60.00 65.00 VESA(XGA) O
6. 1280*768 47.776 59.87 79.50 CVT(WXGA) O
7. 1360*768 47.712 60.015 85.50 VESA(WXGA) O
8. 1280*1024 63.981 60.020 108.00 VESA(SXGA) O
9. 1600*1200 75.00 60.00 162 VESA(UXGA) O
10. 1920*1080 67.50 60 148.5 HDTV 1080P O
RGB PC Monitor Range Limits

Min Vertical Freq - 56 Hz
Max Vertical Freq - 62 Hz
Min Horiz. Freq - 30 kHz
Max Horiz. Freq - 80 kHz
Pixel Clock - 170 MHz
Copyright LG Electronics. Inc. All right reserved. - 10 - LGE Internal Use Only
9. HDMI input (PC/DTV)
PC DDC
1. 640*350 31.468 70.09 25.17 EGA X
2. 720*400 31.469 70.08 28.32 DOS O
3. 640*480 31.469 59.94 25.17 VESA(VGA) O
4. 800*600 37.879 60.31 40.00 VESA(SVGA) O
5. 1024*768 48.363 60.00 65.00 VESA(XGA) O
6. 1280*768 47.776 59.870 79.50 CVT(WXGA) X
7. 1360*768 47.712 60.015 85.50 VESA(WXGA) X
8. 1280*1024 63.981 60.020 108.00 VESA(SXGA) O
9. 1600*1200 75.00 60.00 162 VESA(UXGA) O
10. 1920*1080 67.5 60 148.5 HDTV 1080P O
DTV
1. 720*480 31.50 60 27.027 SDTV 480P
2. 720*480 31.47 59.94 27.00 SDTV 480P
3. 720*576 31.25 50* 13.5 SDTV 576P
4. 1280*720 37.5 50* 74.25 HDTV 720P
5. 1280*720 45.00 60.00 74.25 HDTV 720P
6. 1280*720 44.96 59.94 74.176 HDTV 720P
7. 1929*1080 28.125 50* 74.25 HDTV 1080I
8. 1920*1080 33.75 60.00 74.25 HDTV 1080I
9. 1920*1080 33.72 59.94 74.176 HDTV 1080I
10. 1920*1080 56.25 50* 148.5 HDTV 1080P
11. 1920*1080 67.50 60 148.50 HDTV 1080P
12. 1920*1080 67.432 59.94 148.352 HDTV 1080P
13. 1920*1080 27.00 24.00 74.25 HDTV 1080P
14. 1920*1080 26.97 23.976 74.176 HDTV 1080P
15. 1920*1080 33.75 30.00 74.25 HDTV 1080P
16. 1920*1080 33.71 29.97 74.176 HDTV 1080P
HDMI Monitor Range Limits

Min Vertical Freq - 56 Hz Max Vertical Freq - 62 Hz
Min Horiz. Freq - 30 kHz Max Horiz. Freq - 80 kHz
Pixel Clock - 170 MHz
ADJUSTMENT INSTRUCTION
1. Application Range 4. PCB Assembly Adjustment
This specification sheet is applied all of the LJ03D/E LCD TV 4.1. MAC Address
models, which produced in manufacture department or similar
LG TV factory
4.1.1. Equipment & Condition
Play file: Serial.exe
MAC Address edit
Input Start / End MAC address
2. Notice
(1) Because this is not a hot chassis, it is not necessary to use 4.1.2 Download method
an isolation transformer. However, the use of isolation 4.1.2.1 Communication Prot connection
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of PCBA PC(RS-232C)
25 C 5 C of temperature and 65 % 10 % of relative
humidity if there is no specific designation.
(4) The input voltage of the receiver must keep AC 100-220
V~ 50 / 60Hz. RS-232C Po rt
(5) Before adjustment, execute Heat-Run for 5 minutes.
Connect: PCBA Jig-> RS-232C Port== PC-> RS-232C Port
A After Receive 100% Full white pattern (06CH) then
process Heat-run 4.1.2.2 MAC Address Download
(or 8. Test pattern condition of Ez-Adjust status) Com 1,2,3,4 and 115200(Baudrate)
A How to make set white pattern Port connection button click(1)
1) Press Power ON button of Service Remocon
2) Press ADJ button of Service remocon. Select 8. Test
pattern and, after select White using navigation
button, and then you can see 100% Full White pattern.
* In this status you can maintain Heat-Run useless any

pattern generator
* Notice: if you maintain one picture over 20 minutes
(Especially sharp distinction black with white
pattern 13Ch, or Cross hatch pattern 09Ch)
then it can appear image stick near black level.
3. Adjustment Items
3.1. PCB Assembly Adjustment Load button click(2) for MAC Address write.
A MAC Address Download Start MAC Address write button(3)
Check the OK Or NG
A Adjust 480i Comp1
A Adjust 1080p Comp1/RGB 4.1.3 Equipment & Condition
If it is necessary, it can adjustment at Manufacture Line Each other connection to LAN Port of IP Hub and Jig
You can see set adjustment status at 1. ADJUST
CHECK of the In-start menu
A EDID (The Extended Display Identification Data)/DDC
(Display Data Channel) download
3.2. Set Assembly Adjustment

A Color Temperature (White Balance) Adjustment
A Using RS-232C
A PING Test
A Selection Factory output option
4.1.4 LAN inspection solution 4.2. Using RS-232C
LAN Port connection with PCB Adjust 3 items at 3.1 PCB assembly adjustments adjustment
Network setting at MENU Mode of TV sequence one after the order.
Setting automatic IP
Setting state confirmation A Adjustment protocol
- If automatic setting is finished, you confirm IP and MAC
Address.
4.1.5 LAN Port Inspection (PING Test) See ADC Adjustment RS232C Protocol_Ver1.0
A Necessary items before Adjustment items

Pattern Generator : (MSPG-925FA)
Adjust 480i Comp1 (MSPG-925FA:model :209 , pattern
:65) Comp1 Mode
Adjust 1080p Comp1 (MSPG-925FA:model :225 ,
pattern :65) Comp1 Mode
4.1.5.1 Equipment setting Adjust RGB (MSPG-925FA:model :225 , Pattern :65)
1) Play the LAN Port Test PROGRAM. RGB-PC Mode
2) Input IP set up for an inspection to Test Program.
*IP Number : 12.12.2.2 * If you want more information then see the below
Adjustment method (Factory Adjustment)
4.1.6 LAN Port Inspection (PING Test)
1) Play the LAN Port Test Program. A Adjustment sequence
2) connect each other LAN Port Jack. aa 00 00: Enter the ADC Adjustment mode.
3) Play Test (F9) button and confirm OK Message. xb 00 40: Change the mode to Component1 (No actions)
4) remove LAN CABLE ad 00 10: Adjust 480i Comp
ad 00 10: Adjust 1080p Comp
xb 00 60: Change to RGB-PC mode(No action)
ad 00 10: Adjust 1080p RGB
xb 00 90: Endo of Adjustmennt
5 Factory Adjustment 5.2 EDID (The Extended Display
5.1 Manual Adjust Component 480i/1080p Identification Data) / DDC (Display Data
RGB 1080p Channel) Download.
A Summary : Adjustment component 480i/1080i and RGB A Summary

1080p is Gain and Black level setting at Analog to Digital It is established in VESA, for communication between PC
converter, and compensate the RGB deviation and Monitor without order from user for building user
condition. It helps to make easily use realize Plug and
A Using instrument Play function.
Adjustment remocon, 801GF(802B, 802F, 802R) or
MSPG925FA pattern generator (It can output 480i/1080i For EDID data write, we use DDC2B protocol.
horizontal 100% color bar pattern signal, and its output
level must setting 0.7V0.1V p-p correctly) A Auto Download
After enter Service Mode by pushing ADJ key,
Enter EDID D/L mode.
Enter START by pushing OK key.
=> Caution : - Never connect HDMI & D-sub Cable when

the user downloading .
- Use the proper cables below for EDID
Writing.
<Pic.4 Adjustment pattern : 480i / 1080p 60Hz Pattern >
A You must make it sure its resolution and pattern cause

every instrument can have different setting
A Adjustment method 480i Comp1, Adjust 1080p Comp1/RGB

(Factory adjustment)
ADC 480i Component1 adjustment
- Check connection of Component1
- MSPG-925FA -> Model: 209, Pattern 65
Set Component 480i mode and 100% Horizontal Color
Bar Pattern(HozTV31Bar), then set TV set to
Component1 mode and its screen to NORMAL
ADC 1080p Component1 / RGB adjustment
- Check connection both of Component1 and RGB
- MSPG-925FA -> Model: 225, Pattern 65
Set Component 1080p mode and 100% Horizontal Color
Bar Pattern(HozTV31Bar), then set TV set to
Component1 mode and its screen to NORMAL Edid data and Model option download (RS232)
After get each the signal, wait more a second and enter
the IN-START with press IN-START key of Service
remocon. After then select 7. External ADC with
navigator button and press Enter.
After Then Press key of Service remocon Right
Arrow(VOL+)
You can see ADC Component1 Success
Component1 1080p, RGB 1080p Adjust is same method.
Component 1080p Adjustment in Component1 input
mode
RGB 1080p adjustment in RGB input mode
If you success RGB 1080p Adjust. You can see ADC
RGB-DTV Success
5.2.1 Manual Download - HDMI-3 EDID table (0x04, 0x3A)
A Write HDMI EDID data
Using instruments
- Jig. (PC Serial to D-Sub connection) for PC, DDC
adjustment.
- S/W for DDC recording (EDID data write and read)
- D-sub jack
- Additional HDMI cable connection Jig.
Preparing and setting.

- Set instruments and Jig. Like pic.5), then turn on PC and
Jig.
- Operate DDC write S/W (EDID write & read)
- It will operate in the DOS mode.
- HDMI-4 EDID table (0x04, 0x2A)

VSC
PC
B/D
Pic.3) For write EDID data, setting Jig and another instruments.
EDID data for LJ03B/D/E/R Chassis (Model name = LG TV)
- Analog (RGB) EDID table (0x1D)
See Working Guide if you want more information about EDID

communication.
5.3 Adjustment Color Temperature (White A White Balance Adjustment
If you cant adjust with inner pattern, then you can adjust it
balance) using HDMI pattern. You can select option at Ez-Adjust
Menu 7. White Balance there items NONE, INNER,
A Using Instruments HDMI. It is normally setting at inner basically. If you cant
Color Analyzer: CA-210 (CH 9) adjust using inner pattern you can select HDMI item, and
- Using LCD color temperature, Color Analyzer (CA-210) you can adjust.
must use CH 9, which Matrix compensated (White, Red,
Green, Blue compensation) with CS-2100. See the In manual Adjust case, if you press ADJ button of service
Coordination bellowed one. remocon, and enter Ez-Adjust Menu 7. White Balance,
Auto-adjustment Equipment (It needs when Auto- then automatically inner pattern operates. (In case of
adjustment It is availed communicate with RS-232C : Inner originally Test-Pattern. On will be selected in The
Baud rate: 115200) Test-Pattern. On/Off.
Video Signal Generator MSPG-925F 720p, 216Gray
(Model: 217, Pattern 78) Connect all cables and equipments like Pic.5)
Set Baud Rate of RS-232C to 115200. It may set 115200
A Connection Diagram (Auto Adjustment) orignally.
Using Inner Pattern Connect RS-232C cable to set
Connect HDMI cable to set
F u l l W h i t e P at t er n C A -100+
COL OR
A NA L Y ZER
T Y PE ; C A -100+
R S-232C
Using HDMI input
A RS-232C Command (Commonly apply)
<Pic.5 Connection Diagram for Adjustment White balance>

wb 00 00: Start Auto-adjustment of white balance.
wb 00 10: Start Gain Adjustment (Inner pattern)
jb 00 c0 :

wb 00 1f: End of Adjustment
* If it needs, offset adjustment (wb 00 20-start, wb 00 2f-
end)
wb 00 ff: End of white balance adjustment (inner pattern
disappear)
O Notice) Adjustment Mapping information Using CA-210 Equipment. (9 CH)
- Contrast value: 216 Gray
- White Balance adjustment coordination and color

temperature for Edge(IOP) LED (LJ03D/E)
When Color temperature (White balance) Adjustment
(Automatically)
- Press Power only key of service remocon and operate
automatically adjustment.
- Set BaudRate to 115200.
If it needs, then adjustment Offset.
A White Balance Adjustment (Manual adjustment)

Test Equipment: CA-210
- Using LCD color temperature, Color Analyzer (CA-210)
must use CH 9, which Matrix compensated (White, Red,
Green, Blue compensation) with CS-2100. See the
Coordination bellowed one.
-White Balance adjustment table for Edge (IOP) LED
(LJ03D/E)
Manual adjustment sequence is like bellowed one.
- Turn to Ez-Adjust mode with press ADJ button of
service remocon.
- Select 10.Test Pattern with CH+/- button and press
enter. Then set will go on Heat-run mode. Over 30
minutes set let on Heat-run mode.
- Let CA-210 to zero calibration and must has gap more
10cm from center of LCD module when adjustment.
- Press ADJ button of service remocon and select
G
7.White-Balance in Ez-Adjust then press button
of navigation key.
(When press G button then set will go to full white
mode)
- Adjust at three mode (Cool, Medium, Warm)
- If cool mode
Let B-Gain to 192 and R, G, B-Cut to 64 and then
control R, G gain adjustment High Light adjustment.
- If Medium and Warm mode
Let R-Gain to 192 and R, G, B-Cut to 64 and then
control G, B gain adjustment High Light adjustment.
- All of the three mode
Let R-Gain to 192 and R, G, B-Cut to 64 and then
control G, B gain adjustment High Light adjustment.
- With volume button (+/-) you can adjust.
- After all adjustment finished, with Enter (A key) turn to
Ez-Adjust mode. Then with ADJ button, exit from
adjustment mode
Attachment: White Balance adjustment coordination and

color temperature.
Using CS-1000 Equipment.

- COOL : T=11000K, uv=0.000, x=0.276 y=0.283
- MEDIUM : T=9300K, uv=0.000, x=0.285 y=0.293
- WARM : T=6500K, uv=0.000, x=0.313 y=0.329
5.4 EYE-Q function check 6. GND and ESD Testing
6.1 Prepare GND and ESD Testing.
1) Turn on TV
2) Press EYE key of Adj. R/C
A Check the connection between set and power cord
3) Cover the Eye Q II sensor on the front of the using your
hand and wait for 6 seconds
4) Confirm that R/G/B value is lower than 10 of the Raw Data 6.2 Operate GND and ESD auto-test.
(Sensor data, Back lignt ) . If after 6 seconds, R/G/B value A Fully connected (Between set and power cord) set enter the
is not lower than 10, replace Eye Q II sensor Auto-test sequence.
5) Remove your hand from the Eye Q II sensor and wait for 6 A Connect D-Jack AV jack test equipment.
seconds A Turn on Auto-controller(GWS103-4)
6) Confirm that ok pop up. A Start Auto GND test.
If change is not seen, replace Eye Q II sensor A If its result is NG, then notice with buzzer.
A If its result is OK, then automatically it turns to ESD Test.
A Operate ESD test
A If its result is NG, then notice with buzzer.
A If its result is OK, then process next steps. Notice it with
Good lamp and STOPER Down.Check Items.
A Test Voltage
GND: 1.5KV/min at 100mA
Signal: 3KV/min at 100mA
A Test time: just 1 second.
A Test point
GND test: Test between Power cord GND and Signal
cable metal GND.
ESD test: Test between Power cord GND and Live and
neutral.
A Leakage current: Set to 0.5mA(rms)
5.5 HDCP (High-Bandwidth Digital

Contents Protection) Setting 7. Preset Ch information.
No Need.
5.6 Test of RS-232C control.

Press In-Start button of Service Remocon then set the
4.Baud Rate to 115200. Then check RS-232C control and
5.7 Selection of Country option.

Selection of country option is allowed only North American
model (Not allowed Korean model). It is selection of Country
about Rating and Time Zone. In case of POWER ONLY, System color is operated multi
Models: All models which use LJ03X Chassis (See the first system
page.) In case of IN STOP, System color is operated default system
Press In-Start button of Service Remocon, then enter the (PAN-M)
Option Menu with PIP CH- Button
Select one of these three (USA, CANADA, MEXICO)
defends on its market using Vol. +/-button.
* Caution : Dont push The INSTOP KEY after completing

the function inspection.
8. Default Service option. 9. USB DOWNLOAD (*.epk file
download)
9.1 Put the USB Stick to the USB socket
9.2 Press Menu key, and move OPTION
8.1 ADC-Set.
A R-Gain adjustment Value (default 128) 9.3 Press FAV Press 7 times.
A G-Gain adjustment Value (default 128)
A B-Gain adjustment Value (default 128)
A R-Offset adjustment Value (default 128)
A G-Offset adjustment Value (default 128)
A B-Offset adjustment Value (default 128)
8.2 White balance. Value.
9.4 Select download file (epk file)
9.5 After download is finished, remove the

USB stick.
9.6 Press IN-START key of ADJ remote

control, check the S/W version.
EXPLODED VIEW
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These
parts are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
300 800 400

200
540
530 521
880
820
830
810
120
500
910
920
900
A2 A5 A10
EXT IRQ
SMD GASKET GPIO_00, GPIO_01, GPIO_02,
RESET GPIO_11, GPIO_11, GPIO_39
IC100 IR_INT : GPIO_23

IR1_IN : GPIO_25
GAS4
GAS5
GAS6
GAS8
GAS9
LGE3556C (C0 VERSION)
GAS3
GAS7
GAS1
GAS2
IR2_IN : GPIO_29
6.5T_GAS
CI_A[0-13]
6.5T_GAS
6.5T_GAS
6.5T_GAS
6.5T_GAS
6.5T_GAS
6.5T_GAS
MDS62110206
MDS62110206
MDS62110206
MDS62110206
MDS62110206
IR_OUT : GPIO_26
MDS62110206
MDS62110206
MDS62110206
MDS62110206
CI_A[3] J23 N26 0
OPT R1047
EBI_ADDR3 GPIO_00 POWER_DET INTERRUPT PIN PWM0 : GPIO_24
CI_A[4] J24 L26 0 R192
EBI_ADDR4 GPIO_01 DC INTERRUPT PIN DC 17page : Motion Remocon
+3.3V_NORMAL CI_A[2] H25 N25 PWM1 : GPIO_09
INTERRUPT PIN
OPT
EBI_ADDR2 GPIO_02 ERROR_OUT
OPT
+3.3V_NORMAL CI_A[1] H24 L25
EBI_ADDR1 GPIO_03 MODEL_OPT_4
CI_A[0] H23 K27
R1027
10K
CI_A[5] J25 K28
R1045 EBI_ADDR5 GPIO_05 SIDE_AV_DET
CI_A[6] F26 K24
4.7K EBI_ADDR6 GPIO_06 CI_5V_CTL For CI
CI_A[8] H28 K26 1K R114
R1030 0 EBI_ADDR8 GPIO_07 HDMI_HPD_4
SOC_RESET SYS_RESETb CI_A[9] J26 K25 22 R113
EBI_ADDR9 GPIO_08 DEMOD_RESET 28page : ISDB Demod 17page:M_RFMODULE_RESET
EBI_CS CI_A[13] H27 AA27 DEMOD_RESET
EBI_ADDR13 GPIO_09 PWM_DIM
G26 AA28 1K R1042 22
GAS2-*1
GAS4-*1
CI_A[12] R1029
GAS8-*1
GAS9-*1
5.5T_GAS
5.5T_GAS
GAS1-*1
GAS6-*1
GAS7-*1
5.5T_GAS
5.5T_GAS
5.5T_GAS
5.5T_GAS
EBI_ADDR12 GPIO_10 HDMI_HPD_3
5.5T_GAS
R1053 2.7K +3.3V_NORMAL
MDS62110204
MDS62110204
J27 AA26
MDS62110204
MDS62110204
CI_A[11]
MDS62110204
MDS62110204
MDS62110204
CI_A[10] J28 L1
EBI_ADDR10 GPIO_12 DSUB_DET
CI_A[7] F27 L3
EBI_ADDR7 GPIO_13 BT_RESET BT_RESET 43page : Bluetooth
22 R116 G24 L2
/CI_WAIT EBI_TAB GPIO_14 /RST_HUB
22 R122 H26 Y25
EBI_WE EBI_WE1B GPIO_15 BCM_RX
R117 G27 Y26
33 EBI_CLK_IN GPIO_16 BCM_TX
G28 M27
EBI_CLK_OUT GPIO_17 SC_RE1
22 R127 K23 AA25
EBI_RW EBI_RWB GPIO_18 SC_RE2
22 G25 R25 R111 22
EBI_CS EBI_CS0B GPIO_19 CI_MOD_RESET
R140 N28
GPIO_20 MODEL_OPT_0
GAS2-*2
GAS4-*2
GAS8-*2
GAS9-*2
7.5T_GAS
7.5T_GAS
NAND_DATA[0-7] N27
GAS1-*2
GAS6-*2
GAS7-*2
BT_MUTE
7.5T_GAS
7.5T_GAS
7.5T_GAS
7.5T_GAS
7.5T_GAS
GPIO_21 DD DD 17page : Motion Remocon
MDS62110205
MDS62110205
MDS62110205
MDS62110205
+3.3V_NORMAL
MDS62110205
MDS62110205
MDS62110205
NAND_DATA[0] U24 AH18 R105 56
NAND_DATA0 GPIO_22 AUD_MASTER_CLK
NAND_DATA[1] T26 P23 R199 1K
NAND_DATA1 GPIO_23 HDMI_HPD_2 IR_IN
NAND_DATA[2] T27 M23
NAND_DATA2 GPIO_24 A_DIM
NAND_DATA[3] U26 AD19 R106 1K 12K R1041 EMI
NAND_DATA3 GPIO_25 HDMI_HPD_1 IR_IN C173
4.7K
4.7K
NAND_DATA[4] U27 AE19 R1048 100 C180
NAND_DATA4 GPIO_26 5V_HDMI_1 100pF 22uF
NAND_DATA[5] V26 M4 R109 100 BB Add. 16V
NAND_DATA5 GPIO_27 EPHY_ACTIVITY 50V
NAND_DATA[6] V27 M5 R110 100
NAND_DATA6 GPIO_28 EPHY_LINK
NAND_DATA[7] V28 L23
R194
R193
NAND_DATA7 GPIO_29 /CI_CD1 For CI
NAND_CEb T24 Y28 BCM_AVC_DEBUG_TX1
NAND_CS0B GPIO_30 M_REMOTE_TX M_REMOTE_TX 17page : Motion Remocon
NAND_ALE R23 Y27 BCM_AVC_DEBUG_RX1
NAND_ALE GPIO_31 M_REMOTE_RX
NVRAM NAND_REb T23 G2 M_REMOTE_RX 17page : Motion Remocon
NAND_REB GPIO_32 VREG_CTRL VREG_CTRL 43page : Bluetooth
NAND_CLE T25 G3
+3.3V_NORMAL NAND_CLE GPIO_33 TUNER_RESET
From wireless_I2C to micom I2C NAND_WEb R24 G5 R107 100
NAND_WEB GPIO_34 DTV_ATV_SELECT
+3.3V_NORMAL NAND_RBb U25 G6 R108 100
NAND_RBB GPIO_35 5V_HDMI_2 R115 1.8K
G4
+3.3V_NORMAL GPIO_36 AV_CVBS_DET For CI
L24 0 R1044
GPIO_37 CI_OUTCLK
W24 P25 R1033 22
C103 SF_MISO GPIO_38 /CI_CD2
IC102 U23 L5 R1046 22
M24M01-HRMN6TP 0.1uF SF_MOSI GPIO_39 /CI_IREQ
4.7K
V23 K4
R1025
SF_SCK GPIO_40 MODEL_OPT_6
V24 K1
NC VCC SF_CSB GPIO_41 MODEL_OPT_3
10K
OPT
L27
R173
1 8
GPIO_42 WIRELESS_DL_RX
R1032 M26
0 E1 WP GPIO_43 WIRELESS_DL_TX
2 7 N23 R132 22
GPIO_44 FE_TS_VAL_ERR External Demod.
R28 R1050 100
E2 SCL GPIO_45 5V_HDMI_3
3 A8h 6 R1026 22
SCL3_3.3V
R27 R161 100
GPIO_46 5V_HDMI_4
R26 R133 22
VSS SDA GPIO_47 MODEL_OPT_2
4 5 R1028 22 P28
SDA3_3.3V SCART1_DET
G
Q103 GPIO_48
P27
C171 C167 FDV301N GPIO_49 SIDE_COMP_DET SIDE_COMP_DET
8pF 8pF K6 R103 0
GPIO_50 RF_SWITCH_CTL_CHB RF_SWITCH_CTL_CHB 15page : CHB_SUB_TUNER
OPT OPT WIRELESS_SDA K5 R129
D
S
SDA2_3.3V 22 RGB_DDC_SCL
GPIO_51
G
OPT P26 100 R160 R1052 +3.3V_NORMAL R187-*1 R184-*1
+3.3V_NORMAL
GPIO_52 FRC_RESET 4.7K 2.2K 2.2K
Q104 M3 22 R102
FDV301N * I2C MAP GPIO_53 RGB_DDC_SDA
M2 22 R1049 NON_EU NON_EU
WIRELESS_SCL GPIO_54
D
S
SCL2_3.3V
M1
OPT GPIO_55 COMP2_DET
* I2C_0 : L4 22 R1051
GPIO_56 LG5111_RESET
1.2K
1.2K
1.2K
1.2K
1.2K
1.2K
1.2K
1.2K
L6 LOCAL DIMMING
R187
R184
R183
R180
R177
R176
R171
R170
GPIO_57 HP_DET LG5111_RESET

R123 0 WIRELESS * I2C_1 : W27
SGPIO_00 SCL0_3.3V
W28
R124 SGPIO_01 SDA0_3.3V
0 WIRELESS * I2C_2 : W26
SGPIO_02 SCL1_3.3V
W25
SGPIO_03 SDA1_3.3V
* I2C_3 : J2
SGPIO_04 SCL2_3.3V
J1
SGPIO_05 SDA2_3.3V
K3
SGPIO_06 SCL3_3.3V
K2
SGPIO_07 SDA3_3.3V
Boot Strap * NAND FLASH MEMORY 4Gbit (512M for BB)

Default Res. of all NAND pin is Pull-down
+3.3V_NORMAL
+3.3V_NORMAL
NAND_DATA[0-7] R1000
2.7K
NAND_DATA[0] OPT R1008
R1036 2.7K IC101
OPT 2.7K
NAND04GW3B2DN6E
NAND_DATA[1]
R1005
R1040 2.7K
OPT 2.7K
NC_1 NC_29
NAND_DATA[2] R169 1 48
NAND FLASH
R1039 2.7K NC_2 NC_28
2.7K 2 47
2.7K
NAND_DATA[3]
2.7K
OPT R1004 NC_3 NC_27
3 46
2.7K
R1037OPT NC_4 NC_26 NAND_DATA[0-7]
2.7K 4 45 MODEL OPTION
NAND_DATA[4]
R1003
NC_5 I/O7 NAND_DATA[7] LOW
R191
R1002 2.7K 5 44 PIN NAME PIN NO. HIGH
R134
OPT 2.7K
NAND_DATA[5] NC_6 I/O6 NAND_DATA[6]
R1035 6 43 MODEL_OPT_0 N28 URSA3 NON_URSA3
R1034 2.7K Open Drain RB I/O5
2.7K NAND_RBb 7 42 NAND_DATA[5] +3.3V_NORMAL
MODEL_OPT_1 AA26 MAIN_MINI_LVDS MAIN_LVDS
NAND_DATA[6] OPT R1007 R I/O4
NAND_REb 8 41 NAND_DATA[4]
R1006 2.7K MODEL_OPT_2 R26 DDR-256M DDR-512M
OPT2.7K E NC_25
NAND_DATA[7] NAND_CEb 9 40
1K
1K
1K
1K
1K
1K
R1038
1K
NC_7 NC_24
+3.3V_NORMAL MODEL_OPT_3 K1 FHD HD
R158 OPT 2.7K 10 39
C116
2.7K
4700pF NC_8 NC_23 MODEL_OPT_4 NON_FRC
FHD
FRC
FRC
GIP
11 38 C136 10uF L25

R156
OLED
NAND_ALE 10V
2.7K
DDR_512MB
VDD_1 VDD_2
R1017
R1022
R1011
R1020
R157 OPT
R118
R1009
R1013
2.7K C114 12 37 MODEL_OPT_5 K27 GIP NON-GIP

C115
0.1uF VSS_1 VSS_2 0.1uF
R1001 R1012 100
NAND_CLE 13 36 IF_AGC_SEL MODEL_OPT_0 MODEL_OPT_6 K4 OLED NON_OLED
2.7K
MINI_LVDS/NO LOCAL_D
LNA2_CTL/BOSTER_CTL R1019 100

NC_9 NC_22 MODEL_OPT_1
EXTERNEL FRC/T_CON FRC
14 35 R1024 100
NAND_DATA[0-7]
RF_SWITCH_CTL MODEL_OPT_2
NAND_IO[0] : Flash Select (1) NC_10 NC_21 R181 100
0 : Boot From Serial Flash 15 34 BT_ON/OFF MODEL_OPT_3 *MODEL_OPT_0 & MODEL_OPT_4
1 : Boot From NAND Flash BCM BT MODULE REFER TO THIS OPTION
CL NC_20 BT_ON/OFF MODEL_OPT_4 15page:TW_9910_RESET
NAND_CLE 16 33
NAND_IO[1] : NAND Block 0 Write (DNS) AL I/O3 NAND_DATA[3] 43page : Bluetooth MODEL_OPT_515page:CHB_RESET MODEL_OPT_0 MODEL_OPT_4
0 : Enable Block 0 Write NAND_ALE 17 32 R130 22
/CI_SEL MODEL_OPT_6 LOW LOW NO FRC
1 : Disable Block 0 Write W I/O2 NAND_DATA[2]
NAND_WEb 18 31 HIGH LOW URSA3 Internal
1K
1K
1K
1K
1K
1K
1K
NAND_IO[3:2] : NAND ECC (1, DNS) WP I/O1 NAND_DATA[1] HIGH HIGH URSA3 External
+3.3V_NORMAL 19 30
00 : No ECC LOW HIGH PWIZ Pannel T-con
01 : 1 ECC Bit NC_11 I/O0 NAND_DATA[0] with LG FRC
HD
10 : 4 ECC Bit 20 29
NO_FRC
11 : 8 ECC Bit
NON_OLED
NC_12 NC_19
NON_GIP
DDR_256MB
R119
21 28
R136
4.7K
LVDS/LOCAL_D
R1021
R1015
R1014
R1018
R1023
R1010
NAND_IO[4] : CPU Endian (0) NC_13 NC_18

0 : Little Endian 22 27
FOR ESD 12V Pattern
NO FRC/INTERNER FRC
1 : Big Endian NC_14 NC_17

C 23 26
NAND_IO[6:5] : Xtal Bias Control (1, DNS) B Q101 NC_15 NC_16
00 : 1.2mA (Fundmental Recommand) FLASH_WP 24 25 +12V
KRC103S
01 : 1.8mA
10 : 2.4mA (3rd over tune Recommand) E
11 : 3.0mA
NAND_IO[7] : MIPS Frequency (DNS)

C178 C179
0 : 405MHz
0.1uF 0.1uF
1 : 378MHz
50V 50V
NAND_ALE : I2C Level (DNS)
0 : 3.3V Switching
1 : 5V Switching
NAND_CLE
0 : Enable D2CDIFF AC (DNS)
1 : Disabe D2CDIFF AC
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM (EUROBBTV) 2009.06.18
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. BCM3556 & NAND FLASH 1
When usding FUNDMENTAl then series R = 0 ohm and CL = 8 pF
IC100 54MHz X-TAL
LGE3556C (C0 VERSION) When usding Dip-type X-tal then series R = 22 ohm and CL = 12 pF
D23 B4
FE_TS_DATA_CLK PKT0_CLK LVDS_TX_0_DATA0_P LVDS_TX_1_DATA4_N013:E7;035:AK20
C24 A4
FE_TS_SERIAL PKT0_DATA LVDS_TX_0_DATA0_N LVDS_TX_1_DATA4_P013:E7;035:AK19
B26 C6
FE_TS_SYNC PKT0_SYNC LVDS_TX_0_DATA1_P LVDS_TX_1_DATA3_N013:E7;035:AK19 C230
A25 B6 22
TP4021 RMX0_CLK LVDS_TX_0_DATA1_N LVDS_TX_1_DATA3_P013:E7;035:AK19 12pF
B25 B3 R212
TP4022 RMX0_DATA LVDS_TX_0_DATA2_P LVDS_TX_1_DATA2_N013:E7;035:AK17
A26 A3
TP4023 RMX0_SYNC LVDS_TX_0_DATA2_N LVDS_TX_1_DATA2_P013:E7;035:AK17
A1
CI_OUTDATA[0-7],CI_OUTSTART,CI_OUTVALID LVDS_TX_0_DATA3_P LVDS_TX_1_DATA1_N013:E7;035:AK17
045:V14 A2
LVDS_TX_0_DATA3_N LVDS_TX_1_DATA1_P013:E7;035:AK16
CI_A[14] G23 D5
C257
POD2CHIP_MCLKI LVDS_TX_0_DATA4_P LVDS_TX_1_DATA0_N013:E7;035:AK16
D6
2
CI_OUTDATA[0] D25
POD2CHIP_MDI0 LVDS_TX_0_DATA4_N LVDS_TX_1_DATA0_P013:E7;035:AK16
CI_OUTDATA[1] D24 C5
3
POD2CHIP_MDI1 LVDS_TX_0_CLK_P LVDS_TX_1_CLK_N 013:E7;035:AK18
CI_OUTDATA[2] C25 B5 54MHz_XTAL_N
X903
54MHz
POD2CHIP_MDI2 LVDS_TX_0_CLK_N LVDS_TX_1_CLK_P 013:E7;035:AK18
L208
1
CI_OUTDATA[3] E27 B1
POD2CHIP_MDI3 LVDS_TX_1_DATA0_P LVDS_TX_0_DATA4_N013:F7;035:AK15 54MHz_XTAL_P
CI_OUTDATA[4] E26 B2
POD2CHIP_MDI4 LVDS_TX_1_DATA0_N LVDS_TX_0_DATA4_P013:F7;035:AK14
1008LS-272XJLC 33pF
POD2CHIP_MDI5 LVDS_TX_1_DATA1_P LVDS_TX_0_DATA3_N013:F7;035:AK14
POD2CHIP_MDI6 LVDS_TX_1_DATA1_N
R243
604
LVDS_TX_0_DATA3_P013:F7;035:AK14
CI_OUTDATA[7] D26 D1
POD2CHIP_MDI7 LVDS_TX_1_DATA2_P LVDS_TX_0_DATA2_N013:F7;035:AK12
CI_OUTSTART E23 D2
POD2CHIP_MISTRT LVDS_TX_1_DATA2_N LVDS_TX_0_DATA2_P013:F7;035:AK12
CI_OUTVALID E24 E1
POD2CHIP_MIVAL LVDS_TX_1_DATA3_P LVDS_TX_0_DATA1_N013:E7;035:AK12
F25 E2 22
CHIP2POD_MCLKO LVDS_TX_1_DATA3_N LVDS_TX_0_DATA1_P013:E7;035:AK11 R211 12pF
C27 E3
CHIP2POD_MDO0 LVDS_TX_1_DATA4_P LVDS_TX_0_DATA0_N013:E7;035:AK11 C229
C26 E4
CHIP2POD_MDO1 LVDS_TX_1_DATA4_N LVDS_TX_0_DATA0_P013:E7;035:AK11
B28 D3 A1.2V A2.5V
CHIP2POD_MDO2 LVDS_TX_1_CLK_P LVDS_TX_0_CLK_N 013:E7;035:AK13
B27 D4
CHIP2POD_MDO3 LVDS_TX_1_CLK_N LVDS_TX_0_CLK_P 013:E7;035:AK13
A27 F5 C228 OPT
CHIP2POD_MDO4 LVDS_PLL_VREG 10uF
VIDEO INCM
F24 F1
CHIP2POD_MDO5 LVDS_TX_AVDDC1P2
F23 F4
CHIP2POD_MDO6 LVDS_TX_AVDD2P5_1
A3.3V A1.2V A2.5V E25 F2
CHIP2POD_MDO7 LVDS_TX_AVDD2P5_2
C28 C1
CHIP2POD_MOSTRT LVDS_TX_AVSS_1 PLACE NEAR BCM CHIP
A28 F3
CHIP2POD_MOVAL LVDS_TX_AVSS_2
C4
0
0
L202 LVDS_TX_AVSS_3
A5
0.1uF
0.1uF
0.1uF
4.7uF
4.7uF
BLM18PG121SN1D LVDS_TX_AVSS_4
R236
R237
C258 0.1uF
C236
C239
C242
C295
C2013
AC18 E5 Near Q1705 TU_CVBS_INCM
VDAC_AVDD2P5 LVDS_TX_AVSS_5 Run Along TUNER_CVBS_IF_P Trace
AF20 E6 003:A3
VDAC_AVDD1P2 LVDS_TX_AVSS_6
AG20 D7
VDAC_AVDD3P3_1 LVDS_TX_AVSS_7
AG21 E7
VDAC_AVDD3P3_2 LVDS_TX_AVSS_8
F7
LVDS_TX_AVSS_9
4.7uF
C2019 0.1uF
0.1uF
0.1uF
0.1uF
BROAD BAND STUDIO
C214
C219
C223
G7
C212
Near J1500 SC1_RGB_INCM
LVDS_TX_AVSS_10 A1.2V 003:A4
AF19 H7 Run Along SC1_R,SC_G,SC_B Trace
VDAC_AVSS_1 LVDS_TX_AVSS_11
AD20 A2.5V
R220 : BCM recommened resistor 562 ohm VDAC_AVSS_2
+3.3V_NORMAL AE20
R220 560AH22 VDAC_AVSS_3
AD27
0.1uF
P200 VDAC_RBIAS CLK54_AVDD1P2
C2012
C215 C261 0.1uF
AH20 AD28 REAR_AV_CVBS_INCM
TJC2508-4A 0.1uF VDAC_1 CLK54_AVDD2P5
AG19 AD26 003:A3
C251
0.1uF
VDAC_2 CLK54_AVSS
C213 AC26
0.01uF CLK54_XTAL_N 54MHz_XTAL_N 002:I1
AH21 AC27
75
1%
VDAC_VREG CLK54_XTAL_P 54MHz_XTAL_P 002:I2
R244
34
R248
34
R250
34
R238
AE25
CLK54_MONITOR
R200
1.5K
4.7uF
R201
1.5K
C2028
DTV/MNT_V_OUT Y23
PM_OVERRIDE
2 M25
BSC_S_SCL
M24 C262 0.1uF
BSC_S_SDA Near J1603 COMP2_VID_INCM
AA23 A1.2V Run Along COMP_Y_IN,COMP_Pr_IN,COMP_Pb_IN Trace
3 VCXO_AGND_1
AB24
VCXO_AGND_2
R6 AC24 L203
USB_AVSS_1 VCXO_AGND_3 BLM18PG121SN1D
R245
34
4 T6 AF25
A3.3V USB_AVSS_2 VCXO_AVDD1P2
R7 AF24 C233 C235
A1.2V USB_AVSS_3 VCXO_PLL_AUDIO_TESTOUT 0.1uF 4.7uF
A2.5V T7
USB_AVSS_4
T8
USB_AVSS_5 +3.3V_NORMAL
R3 P24
USB_AVDD1P2 RESET_OUTB
U3 F6 SYS_RESETb
USB_AVDD1P2PLL RESETB 001:A6;001:B7 C2015 0.1uF
L200 T4 N24 4.7K Near P1600 R_VID_INCM
BLM18PG121SN1D USB_AVDD2P5 NMIB Run Along DSUB_R Trace 003:A5
T3 J5 R221
USB_AVDD2P5REF TMODE_0
R4 J4 A2.5V
USB_AVDD3P3 TMODE_1 C2016 0.1uF
U4 J6 L211 G_VID_INCM
USB_RREF TMODE_2 BLM18PG121SN1D Run Along DSUB_G Trace 003:A5
V1 J3
43page : Bluetooth BT_DM BT_DM USB_DM1 TMODE_3
V2 V25 A1.2V C264 0.1uF
BT_DP USB_DP1 SPI_S_MISO C231 C234 B_VID_INCM
Route INCM between associated 43page : Bluetooth
0.1uF
0.1uF
0.1uF
4.7uF
0.1uF
BT_DP C201 R209 U1 AH3 10uF 0.1uF
left and right signals of same channel 3.9K SIDE_USB_DM USB_DM2 POR_OTP_VDD2P5 Run Along DSUB_B Trace 003:A5
100pF U2 AB8
D3.3V SIDE_USB_DP USB_DP2 POR_VDD1P2
R246
34
R247
34
R251
34
The INCM trace ends at the T5 +3.3V_NORMAL

R210 USB_MONCDR
same point where the connector 120 R5 H4
C207
C208
C209
C202
C203
ground connects to the board ground USB_MONPLL EJTAG_TCK
R266 R1 H3
(thru-hole connector pin). OPT OPT
R235 USB_PWRFLT_1 EJTAG_TDI
2.7K R2 H2 R224 R225
Place test points, resistors USB_PWRFLT_2 EJTAG_TDO
2.7K T2 H1 2.7K 2.7K
near audio connector. USB_PWRON_1 EJTAG_TMS
Connect the other side of T1 G1 1K R249
USB_PWRON_2 EJTAG_TRSTB C2011 0.1uF
the resistor to GND as close H6 Near J1500 SC1_CVBS_INCM 003:A3
as possible to the ground EJTAG_CE0 Run Along SC1_CVBS_IN Trace
H5
connection of the associated EJTAG_CE1
audio connector. R218 P6
240 EPHY_VREF R226
1K R219 P5 L204 A1.2V R227
EPHY_RDAC
R260
34
P3 AB26 BLM18PG121SN1D 2.7K 2.7K

EPHY_RDN EPHY_RDN PLL_MAIN_AVDD1P2
P2 AC25
EPHY_RDP EPHY_RDP PLL_MAIN_AGND
N3 AB27 R240
A2.5V A1.2V
EPHY_TDN EPHY_TDN PLL_MAIN_MIPS_EREF_TESTOUT
BLM18PG121SN1D N2 M6 390 L207 A1.2V C2023 0.1uF
EPHY_TDP EPHY_TDP PLL_RAP_AVD_TESTOUT Near J1501 SIDE_AV_CVBS_INCM 003:A3
P1 N6 OPT BLM18PG121SN1D
BLM18PG121SN1D L209 Run Along SC2_CVBS_IN Trace
EPHY_AVDD1P2 PLL_RAP_AVD_AVDD1P2
BLM18PG121SN1D P4 N7
EPHY_AVDD2P5 PLL_RAP_AVD_AGND
N4
L212 EPHY_PLL_VDD1P2
C240
C241
C237
0.1uF
4.7uF
C238
0.1uF
4.7uF
C2026 C244 N1
R261
34
L210
4.7uF 0.1uF EPHY_AGND_1
N5 AA24
16V EPHY_AGND_2 BYP_CPU_CLK
0.1uF
4.7uF
C2020
C2021
C247
C2018
P7 Y24
0.1uF
4.7uF
EPHY_AGND_3 BYP_DS_CLK
AE24 1K R222
BYP_SYS216_CLK
AD25 1K R262
BYP_SYS175_CLK
041:B5 R204 51 C206 0.015uF AE6
REAR_AV_L_IN AUDMX_LEFT1
R214 51 C210 0.015uF AD7 TP is Necessory
041:B5 REAR_AV_R_IN AUDMX_RIGHT1 AUDIO INCM
AF6
002:J6 REAR_AV_LR_INCM AUDMX_INCM1
COMP2_L_IN R215 51 C211 0.015uF AH4
AUDMX_LEFT2 PLACE NEAR BCM CHIP
COMP2_R_IN R228 51 C232 0.015uF AG5
AUDMX_RIGHT2
AG4 PLACE NEAR Jacks
002:J6 COMP2_LR_INCM AUDMX_INCM2
041:B5 R229 51 C220 0.015uF AG6
SC1_L_IN AUDMX_LEFT3 5.1
041:B5 R230 51 C221 0.015uF AF7
SC1_R_IN AUDMX_RIGHT3 SIDE_AV_LR_INCM
002:J7 AE7 Near J1501
SC1_LR_INCM AUDMX_INCM3 R256 002:C6
AH5 Route Between SC2_L_IN & SC2_R_IN 0.15uF
041:B5 R231 51 C224 0.015uF
SIDE_AV_L_IN AUDMX_LEFT4 C2014 0.47uF
041:B5 R232 51 C225 0.015uF AG7
SIDE_AV_R_IN AUDMX_RIGHT4 C271
AH6
002:J6 SIDE_AV_LR_INCM AUDMX_INCM4
009:I3 R233 51 C226 0.015uF AD8
PC_L_IN AUDMX_LEFT5 5.1
009:I3 R234 51 C227 0.015uF AF8
PC_R_IN AUDMX_RIGHT5 002:C6
REAR_AV_LR_INCM
AE8 Near J1600 R258
002:J7 PC_LR_INCM AUDMX_INCM5 Route Between AV1_L_IN & AV1_R_IN 0.15uF
AH7
AUDMX_LEFT6 C2024 0.47uF
AH8
AUDMX_RIGHT6 C2017
AG8
AUDMX_INCM6
AF5
AUDMX_AVSS_1
AB9
AUDMX_AVSS_2 5.1
AA10 COMP2_LR_INCM
AUDMX_AVSS_3
AB10 Near J1603 R259 Route Between COMP1_L_IN & COMP1_R_IN 002:C6
AUDMX_AVSS_4 0.15uF
0
C2025
0
AA11 C265
AUDMX_AVSS_5
0.047uF
0.047uF
0.047uF
0.047uF
0.047uF
0.047uF
0.047uF
0.047uF
0.047uF
C222 0.47uF
AB11
0.1uF AUDMX_AVSS_6
AC8
AUDMX_LDO_CAP
AE5
C2027 0.047uF
C277
C279
C296
C298
C299
C252
C253
C254
C256
AUDMX_AVDD2P5
R264
R265
5.1
SC1_LR_INCM
Near J1500 R257 Route Between SC1_L_IN & SC1_R_IN 002:C6
0.15uF
C2022 0.47uF
A2.5V C270
C217 5.1
10uF PC_LR_INCM
Near J1602 R252 Route Between PC_L_IN & PC_R_IN 002:C6
0.15uF
C269 0.47uF
C2010
Near Q1704
TU_SIF_INCM 003:A3
Route Along With TUNER_SIF_IF_N
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. BCM3556 AUD_IN/LVDS 2
D1.2V
D3.3V
Place here for common circuit with ATSC D1.2V
+1.8V_AMP +1.8V_HDMI +3.3V_NORMAL A3.3V

C245 C255 C377 C375 C263 C373 C267 C289 C291
L111 C383 C246 C378 C376 C259 C374 C366 C266 C288 C290 4.7uF 1000pF 0.01uF 0.1uF 4.7uF 1000pF 0.01uF 0.1uF 10uF
BLM18PG121SN1D L112 C243 C249 C250 C382 C381 C380 C379 C286 C287 1000pF 0.01uF 0.1uF 4.7uF 1000pF 0.01uF 0.1uF 4.7uF 1000pF 0.01uF
CIC21J501NE 0.1uF 4.7uF 1000pF 0.01uF 0.1uF 10uF 10uF 33uF 100uF
C2008 FOR ESD

C2007
0.1uF 0.1uF
16V 16V
D3.3V D1.8V
IC100
26page : TUNER(HALF NIM) LGE3556C (C0 VERSION)
AG28 AE18 C216 C268 C371 C370 C369 C292 C293 C294
TU_IF_AGC_1 DS_AGCI_CTL I2S_CLK_IN C274 C272 C275 C276 C278 C280 C297
AH28 AF18 0.1uF 1000pF 0.01uF 0.1uF 4.7uF 1000pF 0.01uF 0.1uF C2004
TU_IF_AGC_2 DS_AGCT_CTL I2S_CLK_OUT AUD_SCK 0.1uF 0.1uF 0.1uF 0.1uF 4.7uF 4.7uF 4.7uF 33uF
AA21 AD17
EDSAFE_AVSS_1 I2S_DATA_IN
A2.5V AB22 AH19
TU_IF_AGC_1 EDSAFE_AVSS_2 I2S_DATA_OUT AUD_LRCH
AF26 AD18
EDSAFE_AVSS_3 I2S_LR_IN
TU_IF_AGC_2 A1.2V AF27 AG18
EDSAFE_AVSS_4 I2S_LR_OUT AUD_LRCK
BLM18PG121SN1D AF28 AG26
L102 EDSAFE_AVSS_5 AUD_LEFT0_N HP_LOUT_N A2.5V
AG27 AH26
EDSAFE_AVDD2P5 AUD_LEFT0_P HP_LOUT_P
TU_IF_N_1 AE26 AF23
EDSAFE_DVDD1P2 AUD_AVDD2P5_0
TU_IF_P_1 AE28 AA20 C147 C155 C162
C113 C172 EDSAFE_IF_N AUD_AVSS_0_1 0.01uF 0.1uF 10uF
A1.2V AE27 AB21
0.1uF 4.7uF EDSAFE_IF_P AUD_AVSS_0_2
C144 AD24 AC22
TU_IF_N_1 L103 0.1uF PLL_DS_AGND AUD_AVSS_0_3 D1.8V
AB19 AC23
PLL_DS_AVDD1P2 AUD_AVSS_0_4
TU_IF_P_1 BLM18PG121SN1D C119 C122 AB25 AD23
PLL_DS_TESTOUT AUD_AVSS_0_5 D1.8V
0.1uF 4.7uF AH25
A1.2V AUD_RIGHT0_N HP_ROUT_N
A2.5V AG25
AUD_RIGHT0_P HP_ROUT_P
AB18 AH23
BLM18PG121SN1D SD_V5_AVDD1P2 AUD_LEFT1_N BT_LOUT_N
C111 C112 AC17 AG23
SD_V5_AVDD2P5 AUD_LEFT1_P BT_LOUT_P
0.1uF 0.1uF L104 C120 C123 AB17 AG24 C248 C281 C282 C283 C284 C285 C2005 C2006
SD_V5_AVSS AUD_RIGHT1_N BT_ROUT_N C365 C364 C363 C357 C348 C320 C319 C318 C304
1000pF 0.01uF AD14 AH24 1000pF 1000pF 1000pF 1000pF 0.01uF 0.01uF 0.01uF 0.01uF C356
0.1uF 0.1uF 0.1uF 10uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
BLM18PG121SN1D SD_V1_AVDD1P2 AUD_RIGHT1_P BT_ROUT_P
AD16 AE22 16V 16V 16V 10V 16V 16V 16V 16V 16V 16V
SD_V1_AVDD2P5 AUD_AVDD2P5_1
L105 AB15 AB20 C148 C156 C163
SD_V1_AVSS_1 AUD_AVSS_1_1 0.01uF 0.1uF 10uF
C117 AC15 AC21
SD_V1_AVSS_2 AUD_AVSS_1_2
1000pF C118 AD13 AE23
0.01uF SD_V2_AVDD1P2 AUD_AVSS_1_3
AE13 AF21 SCART1_Lout_N
SD_V2_AVDD2P5 AUD_LEFT2_N
DSUB AC13 AE21 SCART1_Lout_P
SD_V2_AVSS_1 AUD_LEFT2_P
AB14 AF22
SD_V2_AVSS_2 AUD_RIGHT2_N SCART1_Rout_N
DSUB_R AC14 AG22
SD_V2_AVSS_3 AUD_RIGHT2_P SCART1_Rout_P
R_VID_INCM AC12 AD21
DSUB_G SD_V3_AVDD1P2 AUD_AVDD2P5_2
AD12 AC20 C149 C157 C164
SD_V3_AVDD2P5 AUD_AVSS_2_1 0.01uF 0.1uF 10uF
G_VID_INCM AB13 AD22
DSUB_B SD_V3_AVSS_1 AUD_AVSS_2_2
AA14 AH2
COMPONENT SD_V3_AVSS_2 AUD_SPDIF SPDIF_OUT
B_VID_INCM AC11 AC6
SD_V4_AVDD1P2 SPDIF_AVDD2P5
R195 10 AD11 AE4
COMP2_Y SD_V4_AVDD2P5 SPDIF_AVSS C150
1% AB12 AF3 0.1uF
COMP2_Pr SD_V4_AVSS SPDIF_IN_N +5V_NORMAL IC100
C127 0.1uF AD10 AH1
COMP2_Pb SD_R SPDIF_IN_P LGE3556C (C0 VERSION)
AC10
COMP2_VID_INCM SD_INCM_R
C128 0.1uF AE9 R2036
C169 47pF
SD_G D1.2V
C101 47pF
C17047pF
R2035
0
AF9 AG1 1K IC100 AD5 P16
1%
SD_INCM_G HDMI_RX_0_CEC_DAT
C129 0.1uF AH9 AA6 LGE3556C (C0 VERSION) DVSS_1 DVSS_62
AD6 R16
1%
SD_B HDMI_RX_0_HTPLG_IN
1%
R120 82
R312 75
C104 OPT
R131 75
R138-*1 AG9 AA5 R309 10K DVSS_2 DVSS_63
A2.5V J7 T16
C130 SD_INCM_B HDMI_RX_0_HTPLG_OUT
0.1uF AG15 AB3 0 R307 DVSS_3 DVSS_64
SC1_RGB(EU)/COMPNENT1[NON_EU] EU 0 SD_Y1 HDMI_RX_0_DDC_SCL HDMI_SCL K7 U16
C131 0.1uF AE15 Y6 0 R308 H8 DVSS_4 DVSS_65
NON_EU SD_PR1 HDMI_RX_0_DDC_SDA HDMI_SDA VDDC_1 L7 V16
COMP1_Y ==> C132 0.1uF AF15 AC4 499 R152 J8 DVSS_5 DVSS_66
SC1_G VDDC_2 M7 AA16
R138 10 SD_PB1 HDMI_RX_0_RESREF C3006 K8
COMP1_Pr ==> SC1_R AH15 AC1 DVSS_6 DVSS_67
SD_INCM_COMP1 HDMI_RX_0_CLK_N HDMI_CLK- 0.1uF VDDC_3 AB7 D17
COMP1_Pb ==> SC1_B C133 0.1uF AG16 AC2 L8 DVSS_7 DVSS_68
SD_Y2 HDMI_RX_0_CLK_P HDMI_CLK+ 16V VDDC_4 AC7 L17
C134 0.1uF AF16 AD1 M8 DVSS_8 DVSS_69
SC1_RGB_INCM HDMI_RX0- VDDC_5 G8 M17
SD_PR2 HDMI_RX_0_DATA0_N
75
75
75
C135 0.1uF AH17 AD2 N8 DVSS_9 DVSS_70
NON_EU SD_PB2 HDMI_RX_0_DATA0_P HDMI_RX0+ A3.3V VDDC_6 D9 N17
ONLY USE NON_EU AH16 AE1 P8 DVSS_10 DVSS_71
R135-*1 SD_INCM_COMP2 HDMI_RX_0_DATA1_N HDMI_RX1- VDDC_7 AA9 P17
1%
FOR COMP 1
1%
C174 0.1uF AG14 AE2 R8 DVSS_11 DVSS_72
OPT 1%
82 1% SD_Y3 HDMI_RX_0_DATA1_P HDMI_RX1+ VDDC_8 G10 R17
R135
R315
R313
C105 OPT
0.1uF AE14 AF1 BLM18PG121SN1D AA8 DVSS_12 DVSS_73
NON_EU
C175
NON_EU
SIDE COMPONENT SD_PR3 HDMI_RX_0_DATA2_N HDMI_RX2- VDDC_9 A11 T17
0.1uF AF14 AF2 L109 H9 DVSS_13 DVSS_74
R196 C176 VDDC_10 L11 U17
SD_PB3 HDMI_RX_0_DATA2_P HDMI_RX2+
10 AH14 AD3 A1.2V A2.5V H10 DVSS_14 DVSS_75
SIDE_COMP_Y SD_INCM_COMP3 HDMI_RX_0_VDD3P3 VDDC_11 M11 V17
1% AH10 AE3 H11 DVSS_15 DVSS_76
SIDE_COMP_Pr SD_L1 HDMI_RX_0_VDD1P2 VDDC_12 N11 AA17
AG10 AC3 H12 DVSS_16 DVSS_77
VDDC_13 P11 AC19
OPT
SIDE_COMP_Pb SD_C1 HDMI_RX_0_VDD2P5 H13
AE10 AD4 C145 C153 C160 DVSS_17 DVSS_78
1%
SIDE_COMP_INCM NON_EU_CN NON_EU_CN SD_INCM_LC1 HDMI_RX_0_AVSS_1 VDDC_14 R11 G18
AE11 AB5 4.7uF 0.1uF 0.1uF H14 DVSS_18 DVSS_79
R2112-*1 R141-*1
1%
BLM18PG121SN1D VDDC_15 T11 L18
1%
SD_L2 HDMI_RX_0_AVSS_2
R165 82
R166 75
C177
R167 75
SIDE_COMP_Y AF11 AB6 H15 DVSS_19 DVSS_80
5% 12 5% 62 SD_C2 HDMI_RX_0_AVSS_3 L107 VDDC_16 U11 M18
SIDE_COMP_Pr AH11 AG2 H16 DVSS_20 DVSS_81
SD_INCM_LC2 HDMI_RX_0_AVSS_4 VDDC_17 V11 N18
SIDE_COMP_Pb R100 62 AH13 AB4 H17 DVSS_21 DVSS_82
SD_L3 HDMI_RX_0_AVSS_5 VDDC_18 D12 P18
SIDE_COMP_INCM R142 OPT AE12 AA7 H18 DVSS_22 DVSS_83
CVBS R143 62 SD_C3 HDMI_RX_0_AVSS_6 VDDC_19 G12 R18
EU_CN AF12 Y8 H19 DVSS_23 DVSS_84
R141 75 1% EU_CN SD_INCM_LC3 HDMI_RX_0_PLL_AVSS C158 C151 C165 VDDC_20 L12 T18
R2112 C110 0.1uF AD9 AC5 H21 DVSS_24 DVSS_85
TU_CVBS SD_CVBS1 HDMI_RX_0_PLL_DVDD1P2 1000pF 0.01uF 10uF VDDC_21 M12 U18
1% 18 R2113 C124 0.1uF AG11 W8 J21 DVSS_25 DVSS_86
REAR_AV_CVBS SD_CVBS2 HDMI_RX_0_PLL_DVSS VDDC_22 N12 V18
12 R2114 C125 0.1uF AG12 K21 DVSS_26 DVSS_87
SC1_CVBS_IN SD_CVBS3 D3.3V VDDC_23 P12 D20
0 R2115 C100 0.1uF AF13 L21 DVSS_27 DVSS_88
VDDC_24 R12 G20
10K
10K
10K
10K
SIDE_AV_CVBS SD_CVBS4 M21
12 AC9 AA3 DVSS_28 DVSS_89
OPT
TU_CVBS_INCM SD_INCM_CVBS1 HDMI_RX_1_CEC_DAT VDDC_25 T12 H20
N21 DVSS_29 DVSS_90
R2037
AF10 V4
REAR_AV_CVBS_INCM SD_INCM_CVBS2 HDMI_RX_1_HTPLG_IN VDDC_26 U12 A21
A2.5V A2.5V AH12 U6 P21 DVSS_30 DVSS_91
SC1_CVBS_INCM SD_INCM_CVBS3 HDMI_RX_1_HTPLG_OUT VDDC_27 V12 E21
R310
AG13 V5 R21 DVSS_31 DVSS_92
R2039
R2038
SD_INCM_CVBS4 HDMI_RX_1_DDC_SCL VDDC_28 L13 F21
SIDE_AV_CVBS_INCM AF17 V3 T21 DVSS_32 DVSS_93
SD_SIF1 HDMI_RX_1_DDC_SDA VDDC_29 M13 G21
R137 R4020 AG17 W4 499 R153 A3.3V U21 DVSS_33 DVSS_94
10K SD_INCM_SIF1 HDMI_RX_1_RESREF VDDC_30 N13 E22
10K AD15 W2 V21 DVSS_34 DVSS_95
0.1uF OPT VDDC_31 P13 F22
SD_FB HDMI_RX_1_CLK_N W21
R128 C106 A1.2V AE16 W3 DVSS_35 DVSS_96
SC1_ID SD_FS HDMI_RX_1_CLK_P R205 VDDC_32 R13 G22
0 L106 AE17 Y1 Y21 DVSS_36 DVSS_97
TU_SIF BLM18PG121SN1D SD_FS2 HDMI_RX_1_DATA0_N 20 VDDC_33 T13 H22
AB16 Y2 DVSS_37 DVSS_98
R3055 HDMI_RX_1_DATA0_P A3.3V U13 J22
R139 PLL_VAFE_AVDD1P2 DVSS_38 DVSS_99
OPT
240 C121 C140 AA15 AA2
12K PLL_VAFE_AVSS HDMI_RX_1_DATA1_N V13 K22
0.1uF 4.7uF AC16 AA1 AH27 DVSS_39 DVSS_100
HDMI_RX_1_DATA1_P AGC_VDDO G14 L22
TU_SIF_INCM AG3 PLL_VAFE_TESTOUT AB2 BLM18PG121SN1D D3.3V DVSS_40 DVSS_101
RGB_HSYNC HDMI_RX_1_DATA2_N L14 M22
AF4 AB1 L110 DVSS_41 DVSS_102
C4020 RGB_VSYNC HDMI_RX_1_DATA2_P C2003 M14 N22
Y3 A1.2V A2.5V AA12 DVSS_42 DVSS_103
12K
R4021
0.1uF 0.1uF VDDO_1 N14 P22
120
HDMI_RX_1_VDD3P3
OPT
Y4 AA13 DVSS_43 DVSS_104
P14 R22
R3056
HDMI_RX_1_VDD1P2 VDDO_2
W5 AA18 DVSS_44 DVSS_105
HDMI_RX_1_VDD2P5 VDDO_3 R14 T22
W1 AA19 DVSS_45 DVSS_106
HDMI_RX_1_AVSS_1 VDDO_4 T14 U22
U5 C146 C154 C161 E28 DVSS_46 DVSS_107
RGB_HSYNC HDMI_RX_1_AVSS_2 VDDO_5 U14 V22
W6 4.7uF 0.1uF 0.1uF L28 DVSS_47 DVSS_108
RGB_VSYNC HDMI_RX_1_AVSS_3 VDDO_6 V14 W22
U7 U28 DVSS_48 DVSS_109
CONNECT NEAR BCM CHIP FOR ESD VDDO_7 L15 Y22
HDMI_RX_1_AVSS_4 AB28
R2117 V7 DVSS_49 DVSS_110
HDMI_RX_1_AVSS_5 VDDO_8 M15 AA22
0 W7 BLM18PG121SN1D D1.8V DVSS_50 DVSS_111
SC1_FB HDMI_RX_1_AVSS_6 L108 C384 N15 W23
U8 33uF DVSS_51 DVSS_112
HDMI_RX_1_AVSS_7 P15 AB23
V8 10V A9 DVSS_52 DVSS_113
HDMI_RX_1_AVSS_8 DDRV_1 R15 F28
Y5 G9 DVSS_53 DVSS_114
DDRV_2 T15 M28
0
HDMI_RX_1_AVSS_9 G11
V6 DVSS_54 DVSS_115
DDRV_3 U15 T28
OPT
HDMI_RX_1_PLL_AVSS G13
AA4 DVSS_55 DVSS_116
R2116
HDMI_RX_1_PLL_DVDD1P2 DDRV_4 V15 AC28
Y7 C159 C152 C166 A14 DVSS_56 DVSS_117
HDMI_RX_1_PLL_DVSS DDRV_5 A16
1000pF 0.01uF 10uF G15 DVSS_57
DDRV_6 G16
G17 DVSS_58
DDRV_7 L16
A19 DVSS_59
DDRV_8 M16
G19 DVSS_60
DDRV_9 N16
DVSS_61

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS EUROBBTV 2009.06.18
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. BCM3556 VIDEO IN 3
D1.8V
A1.2V
IC100
LGE3556C (C0 VERSION) D1.8V
A6 0.1uF C403
DDR_BVDD0
A24 0.1uF C404
DDR_BVDD1
C451
C454
C455
C456
C457
C458
C459
C460
C461
B7
C441
C442
C443
C444
C445
C446
C447
C448
C440
C469
10uF
C470
C471
C472
C473
C474
C475
C476
C477
C478
C479
C480
C481
C482
C495
10uF
10uF
C462
C465
C468
10uF
10uF
22uF
0.1uF
470pF
470pF
DDR_BVSS0
10uF
10uF
10uF
470pF
22uF
0.1uF
0.1uF
10uF
0.1uF
470pF
470pF
470pF
0.047uF
0.1uF
0.1uF
0.1uF
10uF
470pF
0.047uF
0.1uF
B24
470pF
0.047uF
0.047uF
0.047uF
0.047uF
0.047uF
0.047uF
DDR_BVSS1
F20
DDR_PLL_TEST
B23 R411 0
DDR_PLL_LDO
B17 OPT DDR01_CKE
DDR01_CKE DDR_VTT
C22 R412 240
DDR_COMP IC400 IC402
E16 1% DDR01_ODT DDR1_DQ[0-7]
DDR01_ODT NT5TU128M8DE_BD NT5TU128M8DE_BD
C23 DDR0_DQ[0-7] 004:B6
DDR_EXT_CLK 004:B5
B12 DDR01_A[0-3,7-13]
DDR0_CLK 004:C7;004:C4 004:A7;004:C4 DDR0_CLK 004:A7;004:F4 DDR1_CLK SI
DDR0_CLK R407
C12 DDR0_CLKb 004:C7;004:C4 R406 E8 C8 DDR0_DQ[0] E8 C8
DDR0_CLKB DDR1_DQ[0] DDR01_RASb
A13 100 CK DQ0 100 CK DQ0
DDR1_CLK
DDR1_CLK 004:F7;004:F4 DDR0_CLKb 1% F8 C2 DDR0_DQ[1] 004:A7;004:F4 DDR1_CLKb 1% F8 C2 DDR1_DQ[1] DDR01_A[2]
004:A7;004:C4 CK DQ1 CK DQ1 C485
A12 DDR1_CLKb 004:F7;004:F4 F2 D7 DDR0_DQ[2] F2 D7 DDR1_A[4-6] 0.1uF
DDR1_CLKB DDR01_CKE DDR01_CKE DDR1_DQ[5] DDR01_A[0]
B15 DDR01_A[0] CKE DQ2 CKE DQ2
DDR01_A00 D3 DDR0_DQ[3] D3 DDR1_DQ[3] DDR1_A[6] 75
E14 DDR01_A[1] DQ3 DQ3 AR400
DDR01_A[0-3] D1 DDR0_DQ[4] D1 DDR1_DQ[4] DDR0_A[4-6] DDR01_CASb
DDR01_A01 DQ4 DQ4 C486
A15 DDR01_A[2] F7 D9 DDR0_DQ[5] F7 D9 R408 75 0.1uF
DDR01_A02 DDR01_RASb DDR01_RASb DDR1_DQ[2]
D15 DDR01_A[3] RAS DQ5 RAS DQ5
DDR01_A03 DDR01_CASb G7 B1 DDR0_DQ[6] DDR01_CASb G7 B1 DDR1_DQ[6] DDR01_A[12] R409 75
E13 DDR0_A[4] CAS DQ6 CAS DQ6
DDR0_A[4-6] DDR01_WEb F3 B9 DDR0_DQ[7] DDR01_WEb F3 B9 DDR1_DQ[7] DDR01_A[9]
DDR0_A04 WE DQ7 WE DQ7 C487
E12 DDR0_A[5] G8 G8 0.1uF
DDR0_A05 DDR01_A[7]
F13 DDR0_A[6] CS CS
DDR0_A06 DDR01_BA0 DDR01_BA0 DDR1_A[5] 75
C14 DDR01_A[7] B7 B7 AR401
DDR01_A07 DDR01_BA1 DDR0_DQS0 004:A4 DDR01_BA1 DDR1_DQS0 004:A4 DDR1_A[4] C488
F14 DDR01_A[8] DQS DQS
DDR01_A08 G2 A8 DDR0_DQS0b 004:A4 G2 A8 DDR1_DQS0b 004:A3 DDR01_A[11] 75 0.1uF
B14 DDR01_A[9] BA0 DQS BA0 DQS
DDR01_A09 DDR01_A[7-13] G3 B3 DDR0_DM0 004:A4 G3 B3 DDR1_DM0 004:A4 DDR01_A[8]
D14 DDR01_A[10] BA1 DM/RDQS BA1 DM/RDQS
DDR01_A10 DDR01_BA2 G1 A2 DDR01_BA2 G1 A2 DDR01_A[13]
NC_1/BA2 NU/RDQS NC_1/BA2 NU/RDQS C489
C13 DDR01_A[11] 0.1uF
DDR01_A11 DDR01_A[0-3,7-13] DDR01_A[0-3,7-13] DDR01_A[3] AR402
D13 DDR01_A[12] D1.8V D1.8V
DDR01_A12 DDR01_A[1]
B13 DDR01_A[13] H8 A9 H8 A9
DDR01_A13 DDR0_A[4-6] DDR01_A[0] DDR1_A[4-6] DDR01_A[0] DDR01_A[10] C490
F15 DDR1_A[4] A0 VDDQ_1 004:B6;004:F3;004:I7 A0 VDDQ_1
DDR1_A[4-6] DDR01_A[1] H3 C1 DDR01_A[1] H3 C1 DDR01_BA1 75 0.1uF
DDR1_A04 A1 VDDQ_2 A1 VDDQ_2
C15 DDR1_A[5] H7 C3 H7 C3 AR403
DDR1_A05 DDR01_A[2] DDR01_A[2] DDR01_BA0
D16 DDR1_A[6] A2 VDDQ_3 A2 VDDQ_3
DDR1_A06 DDR01_A[3] J2 C7 DDR01_A[3] J2 C7 DDR01_BA2
F16 A3 VDDQ_4 A3 VDDQ_4
DDR01_BA0 DDR01_BA0 DDR0_A[4] J8 C9 DDR1_A[4] J8 C9 DDR01_WEb
B16 A4 VDDQ_5 A4 VDDQ_5
DDR01_BA1 DDR01_BA1 DDR0_A[5] J3 A1 DDR1_A[5] J3 A1 75
A5 VDD_1 A5 VDD_1 DDR01_CKE C499
E15 DDR01_BA2 DDR0_A[6] J7 L1 DDR1_A[6] J7 L1 AR404 0.1uF
DDR01_BA2 A6 VDD_2 A6 VDD_2 DDR01_ODT
A17 DDR01_CASb K2 E9 K2 E9
DDR01_CASB DDR01_A[7] DDR01_A[7] R410 75
A8 A7 VDD_3 A7 VDD_3 C421
DDR0_DQ[0] DDR0_DQ[0-7] DDR01_A[8] K8 H9 DDR01_A[8] K8 H9 0.1uF
DDR0_DQ00 A8 VDD_4 A8 VDD_4
B11 DDR0_DQ[1] K3 K3
DDR0_DQ01 DDR01_A[9] DDR01_A[9]
B8 DDR0_DQ[2] A9 A9 DDR_VTT
DDR01_A[10] H2 A7 DDR01_A[10] H2 A7
DDR0_DQ02 A10/AP VSSQ_1 A10/AP VSSQ_1 PI
D11 DDR0_DQ[3] K7 B2 K7 B2
DDR0_DQ03 DDR01_A[11] DDR01_A[11]
E11 DDR0_DQ[4] A11 VSSQ_2 A11 VSSQ_2
DDR01_A[12] L2 B8 DDR01_A[12] L2 B8
DDR0_DQ04 A12 VSSQ_3 A12 VSSQ_3
C8 DDR0_DQ[5] DDR01_A[13] L8 D2 L8 D2
DDR0_DQ05 DDR01_A[13]
C11 DDR0_DQ[6] A13 VSSQ_4 A13 VSSQ_4
DDR0_DQ06 D8 D8 DDR01_RASb
C9 DDR0_DQ[8-15] VSSQ_5 VSSQ_5
DDR0_DQ[7] A3 A3 DDR01_A[2]
DDR0_DQ07 VSS_1 VSS_1 C491
D8 DDR0_DQ[8] E3 E3 0.1uF
E10 L3 VSS_2 L3 VSS_2
DDR0_DQ[9] NC_2/A14 J1 NC_2/A14 J1 DDR0_A[6] 75
DDR0_DQ09 L7 VSS_3 DDR0_VREF0 L7 VSS_3 DDR1_VREF0
E9 DDR0_DQ[10] K9 K9 AR405
DDR0_DQ10 NC_3/A15 NC_3/A15 DDR01_A[3]
F11 DDR0_DQ[11] VSS_4 VSS_4
DDR0_DQ11 DDR01_A[1] C483
F12 004:A7;004:C5;004:C2;004:F2;004:I4;004:I6
DDR0_DQ[12] F9 E2 F9 E2 DDR01_A[10] 0.1uF
DDR0_DQ12 DDR01_ODT DDR01_ODT
E8 DDR0_DQ[13] ODT VREF ODT VREF
DDR0_DQ13 E1 E1 C463 C466 DDR01_BA1 75
D10 VDDL C449 C452 VDDL
DDR0_DQ[14] E7 E7 DDR01_A[12] AR406
DDR0_DQ14 VSSDL VSSDL
F8 DDR0_DQ[15] DDR1_DQ[0-7] 0.1uF 470pF 470pF 0.1uF
DDR0_DQ15 DDR01_A[9] C484
C18 DDR1_DQ[0] 0.1uF
C20 DDR1_DQ[1]
DDR1_DQ01 DDR0_A[5] 75
A18 DDR1_DQ[2] AR407
DDR1_DQ02 DDR0_A[4]
B21 DDR1_DQ[3]
DDR1_DQ03 DDR01_A[11] C492
C21 DDR1_DQ[4] DDR1_DQ[8-15] 0.1uF
DDR1_DQ04
Close to IC DDR01_A[8]
B18 DDR1_DQ[5] Close to IC
DDR1_DQ05 DDR01_A[13] 75
B20 DDR1_DQ[6] AR408
DDR1_DQ06 DDR01_BA0
D18 DDR1_DQ[7]
DDR1_DQ07 DDR01_BA2 C493
E18 DDR1_DQ[8] 0.1uF
DDR1_DQ08 DDR01_WEb
D21 DDR1_DQ[9]
DDR1_DQ09 75
F18 DDR1_DQ[10] DDR01_CKE
AR409
DDR1_DQ10 DDR01_ODT
E20 DDR1_DQ[11]
DDR1_DQ11 R404 75
A22 DDR1_DQ[12] C494
DDR1_DQ12 0.1uF
F17 DDR1_DQ[13]
DDR1_DQ13
B22 DDR1_DQ[14]
DDR1_DQ14
E17 DDR1_DQ[15]
DDR1_DQ15
A10 DDR0_DM0 004:E6
DDR0_DM0 IC401 IC403 DDR1_DQ[8-15] C496
C10 DDR0_DM1 004:E3 0.1uF
DDR0_DM1 NT5TU128M8DE_BD NT5TU128M8DE_BD
A20 DDR1_DM0 004:H6 DDR0_DQ[8-15] 004:B5
DDR1_DM0
F19 DDR1_DM1 004:H3 004:A7;004:C7 DDR0_CLK DDR1_CLK C497
DDR1_DM1 0.1uF
B10 DDR0_DQS0 004:E6 E8 C8 E8 C8
DDR0_DQS0 DDR0_DQ[9] DDR1_DQ[9]
B9 CK DQ0 CK DQ0
DDR0_DQS0B DDR0_DQS0b 004:E6 DDR0_CLKb F8 C2 DDR0_DQ[8] DDR1_CLKb F8 C2 DDR1_DQ[8]
004:A7;004:C7 CK DQ1 CK DQ1 C498
F10 DDR0_DQS1 004:E3 F2 D7 F2 D7
DDR0_DQS1 DDR01_CKE DDR0_DQ[12] DDR01_CKE DDR1_DQ[12] 0.1uF
F9 CKE DQ2 CKE DQ2
DDR0_DQS1b 004:E3 004:A7;004:C7;004:F7;004:F4 D3 DDR0_DQ[13] D3 DDR1_DQ[13]
DDR0_DQS1B DQ3 DQ3
B19 DDR1_DQS0 004:H6 D1 D1
DDR1_DQS0 DDR0_DQ[15] DDR1_DQ[15]
C19 DQ4 DQ4 SI
DDR1_DQS0b 004:H6 DDR01_RASb F7 D9 DDR0_DQ[11] DDR01_RASb F7 D9 DDR1_DQ[14]
DDR1_DQS0B RAS DQ5 RAS DQ5
E19 DDR1_DQS1 004:H3 G7 B1 G7 B1
DDR1_DQS1 DDR01_CASb DDR0_DQ[10] DDR01_CASb DDR1_DQ[10]
D19 CAS DQ6 CAS DQ6
DDR1_DQS1B DDR1_DQS1b 004:H3 DDR01_WEb F3 B9 DDR0_DQ[14] DDR01_WEb F3 B9 DDR1_DQ[11]
C16 DDR0_VREF0 WE DQ7 WE DQ7
DDR01_RASb G8 G8
DDR01_RASB CS CS
A7 DDR1_VREF0
DDR_VREF0 DDR01_BA0 DDR01_BA0
A23 B7 B7
DDR_VREF1 DDR01_BA1 DDR0_DQS1 004:A4 DDR01_BA1 DDR1_DQS1 004:A3
C17 D1.8V DQS DQS
DDR01_WEb G2 A8 DDR0_DQS1b G2 A8 DDR1_DQS1b 004:A3
DDR01_WEB BA0 DQS 004:A4 BA0 DQS
C7 G3 B3 G3 B3
DDR_VDDP1P8_1 DDR0_DM1 004:A4 DDR1_DM1 004:A4
C410
BA1 DM/RDQS BA1 DM/RDQS
C401
C400
C409
C405
C402
C408
C407
D22 G1 A2 G1 A2
DDR_VDDP1P8_2 DDR01_BA2 NC_1/BA2 NU/RDQS DDR01_BA2 NC_1/BA2 NU/RDQS
C406 C415 DDR01_A[0-3,7-13] DDR01_A[0-3,7-13]
D1.8V D1.8V
1uF
1uF
1uF
1uF
0.1uF 0.1uF
470pF
470pF
470pF
470pF
DDR01_A[0] H8 A9 DDR01_A[0] H8 A9
A0 VDDQ_1 DDR1_A[4-6] A0 VDDQ_1
DDR01_A[1] H3 C1 DDR01_A[1] H3 C1
DDR0_A[4-6] A1 VDDQ_2 004:B6;004:F6;004:I7 A1 VDDQ_2
DDR01_A[2] H7 C3 DDR01_A[2] H7 C3
A2 VDDQ_3 A2 VDDQ_3
DDR01_A[3] J2 C7 DDR01_A[3] J2 C7
A3 VDDQ_4 A3 VDDQ_4
DDR0_A[4] J8 C9 DDR1_A[4] J8 C9
A4 VDDQ_5 A4 VDDQ_5
DDR0_A[5] J3 A1 DDR1_A[5] J3 A1
A5 VDD_1 A5 VDD_1
DDR0_A[6] J7 L1 DDR1_A[6] J7 L1
A6 VDD_2 A6 VDD_2
* DDR_VTT DDR01_A[7] K2 E9 DDR01_A[7] K2 E9
A7 VDD_3 A7 VDD_3
DDR01_A[8] K8 H9 DDR01_A[8] K8 H9
A8 VDD_4 A8 VDD_4
DDR01_A[9] K3 DDR01_A[9] K3
A9 A9
DDR01_A[10] H2 A7 DDR01_A[10] H2 A7
DDR_VTT D3.3V A10/AP VSSQ_1 A10/AP VSSQ_1
DDR01_A[11] K7 B2 DDR01_A[11] K7 B2
A11 VSSQ_2 A11 VSSQ_2
DDR01_A[12] L2 B8 DDR01_A[12] L2 B8
DDR01_A[13] L8 D2 DDR01_A[13] L8 D2
D8 D8
VSSQ_5 VSSQ_5
A3 A3
IC404 VSS_1 VSS_1
C426 C425 E3 E3
C417 C419 C413 D1.8V L3 VSS_2 L3 VSS_2
10uF 10uF BD35331F-E2 J1 J1
10K
10uF 10uF 0.1uF NC_2/A14 NC_2/A14
L7 VSS_3 L7 VSS_3
R418
16V 16V 10V 10V DDR0_VREF0 DDR1_VREF0
16V NC_3/A15 K9 NC_3/A15 K9
VSS_4 VSS_4
GND VTT
1 8 F9 E2 F9 E2
DDR01_ODT ODT VREF DDR01_ODT ODT VREF
E1 E1
VDDL C450 C453 VDDL C464 C467
EN VTT_IN E7 E7
2 7 VSSDL VSSDL
DDR1_VREF0 0.1uF 470pF 470pF 0.1uF
VTTS VCC
3 6
DDR0_VREF0
R417
R414 0 VREF VDDQ 220
4 5
C418
Close to IC Close to IC
R415 0 C416 C420
C422 1uF
1uF 10uF 0.1uF
10V
10V 10V 16V
16V
C411 C412 C423
0.1uF 0.1uF 10uF
C414
16V 16V 10V
0.1uF
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR HONG YEON HYUK
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. DDR Memory 4
COMPONENT1
COMPONENT2
AV1
JK1100
COMPONENT1
PPJ237-01 +3.3V_NORMAL AV <Practically COMP2>
[RD1]E-LUG +3.3V_NORMAL
6C
R1101
10K R1104 NON_SCART
5C [RD1]O-SPRING AV_CVBS_DET
D1100 C1100 1K 9:G3 R1112
100pF 10K
5.6V 50V 1K
4C [RD1]CONTACT SCART1_DET ==> COMP1_DET DTV/MNT_V_OUT
TP1100
D1115 C1112R1116
C1101 1uF 5.6V 100pF
REAR_AV_R_IN SC1_FB
5B [WH1]O-SPRING 25V R1105 C1103 50V TP1101
D1101 R1102 0 10:B5;AF24
100pF
5.6V 470K 50V
TP1102 SC1_ID
4A [YL1]CONTACT
C1102 1uF
REAR_AV_L_IN TP1103 DTV_ATV_SELECT
[YL1]O-SPRING 25V R1106 10:B5;AF22
5A D1102 R1103 0 C1104
470K 100pF SCART1_Rout_P
5.6V 50V TP1104
C1114
[YL1]E-LUG 25V
6A 1uF
REAR_AV_CVBS TP1105 SCART1_Rout_N
D1103 R1107 C1105 11:C4;AL18 SC1_R_IN ==> COMP1_R_IN
[RD2]E-LUG 5.1V 0 47pF R1114
6H 50V D1105 0
D1116 R1109 C1125
5.6V 470K 100pF
5.1V
SC1_CVBS_IN
5H [RD2]O-SPRING_2 C1113 TP1107
25V
1uF
SC_RE1
SC1_L_IN ==> COMP1_L_IN TP1108
4H [RD2]CONTACT
OPT
R1113
R1100
0
D1104 0
R1108 C1124 TP1109
SC_RE2
5.6V 470K 100pF
5G [WH2]O-SPRING
TP1110 SCART1_Lout_N
L1102
5F [RD2]O-SPRING_1 270nH
SC1_R TP1111 SCART1_Lout_P
==> COMP1_Pr
D1106 C1108 C1120
[RD2]E-LUG-S 5.5V 27pF 27pF
7F 50V 50V
L1100
[BL2]O-SPRING 270nH
5E
SC1_B ==> COMP1_Pb
D1107 C1106 C1118
[BL2]E-LUG-S 5.5V 27pF 27pF
7E 50V 50V
4D [GN2]CONTACT
L1101
5D [GN2]O-SPRING 270nH
D1108
SC1_G ==> COMP1_Y
5.1V C1107 C1119 New Item Development
[GN2]E-LUG 27pF 27pF
6D 50V 50V
D1117
5.1V
EARPHONE BLOCK
6N [RD3]E-LUG
HP_LOUT
OPT
5N [RD3]O-SPRING_2
C1130
1000pF
50V R1121 C
OPT E JK1101
OPT
[RD3]CONTACT 1K OPT +3.3V_NORMAL

4N Q1100 B KJA-PH-0-0177
MMBT3904-(F)
MMBT3904-(F) GND 5
B Q1103
JP8818
E C
5M [WH3]O-SPRING
R1125
10K
L 4
R1123
1K DETECT 3
[RD3]O-SPRING_1
JP8819
5L COMPONENT2 HP_ROUT HP_DET

<Practically COMP1> R 1
[RD3]E-LUG-S +3.3V_NORMAL
7L OPT
C1131
1000pF OPT C E
R1115 50V OPT
5K [BL3]O-SPRING R1122 Q1101 B
10K MMBT3904-(F)
OPT
1K MMBT3904-(F) +3.5V_ST
R1119 B Q1102
1K E C
7K [BL3]E-LUG-S C1115 COMP2_DET
R1124
OPT
D1109 100pF 10K

5.6V 50V SIDE_HP_MUTE
4J [GN3]CONTACT
5J [GN3]O-SPRING
C1117
25V
1uF
6J [GN3]E-LUG +3.3V_NORMAL
R1118 COMP2_R_IN EARPHONE AMP

D1114 0
R1111 C1127 L1106
5.6V 470K 100pF
10uH
C1137 C1139
C1116 10uF 0.1uF
25V 10V 16V
1uF R1131 L1107
0 BG2012B080TF
HP_LOUT
R1117 1/16W C1142
0 COMP2_L_IN C1136
D1110 Close to the IC 0.22uF
R1110 C1126 1uF
100pF 16V
5.6V 470K 10V
+3.3V_NORMAL
OUTL
SGND
VDD
EN
R1129
L1103 C1140 100K
270nH C1132 16 15 14 13 2.2uF OPT
COMP2_Pr 1uF 10V R1132 OPT
10V INL- HPVDD 4.7K R1133
D1111 C1109 C1121 1 12
HP_LOUT_N 0
5.5V 27pF 27pF C1133
1uF C
50V 50V 10V INL+ CPP R1134
2 11 1K
HP_LOUT_P Q1104 B
L1104 C1134 IC1100 C1141 2SC3052 SIDE_HP_MUTE
270nH 1uF TPA6132A2 2.2uF
10V INR+ PGND 10V
COMP2_Pb 3 10 E
HP_ROUT_N
D1112 C1135
C1110 C1122 1uF
5.5V 27pF 27pF 10V INR- CPN
4 EAN60724701 9
50V 50V HP_ROUT_P
5 6 7 8
G0
G1
4.7K
R1127
4.7K
R1120
OUTR
HPVSS
L1105
270nH R1130 L1108
COMP2_Y 0 BG2012B080TF
HP_ROUT
OPT
OPT
C1123
R1128
D1113 1/16W
R1126
C1111 C1138 C1143

5.1V 27pF 27pF 2.2uF 0.22uF
50V 10V
D1118 50V 16V
5.1V

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS GP2_BCM 09/10/19
HP/COMP/REAR AV(NON_EU_CN)
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. 11
CAN H-NIM/NIM TUNER for TAIWAN
TU2600-*5
TU2600-*1 TU2600-*2 TDTR-T035F +5V_TU
TDVJ-H031F TDVJ-H001F
Taiwan/Brazil_H
Latin_Tuner_V Latin_Tuner_H RF_S/W_CTL
ANT_PWR[OPT] ANT_PWR[OPT] 1 L2600
1 1
BST_CTL BLM18PG121SN1D
BST_CNTL BST_CNTL 2
2 2
+B1[5V]
+B +B 3
3 3
NC_1[RF_AGC] R2615 Q2601
NC[RF_AGC] 4 R2621
NC[RF_AGC] 0
4 4 E ISA1530AC1 10K
NC_2 R2618
AS AS 5 R2602 0 RF_SWITCH_CTL 2.2K
5 5
SCLT
SCL SCL 6 B
6 6 TU2600 C
SDAT C R2623
SDA SDA 7 R2605 0 Q2604 B 10K
7 7 TDTR-T055F LNA2_CTL/BOSTER_CTL
NC_3 2SC3052
NC(IF_TP) NC(IF_TP) 8
8 8 C2613
SIF E
SIF SIF 9 Taiwan/Brazil_V close to TUNER 0.01uF
9 9 +5V_TU 25V
NC_4
NC NC 10 ANT_PWR[OPT]
10 10 1 close to TUNER OPTION : RF AGC
VIDEO C2609
VIDEO VIDEO 11 C2601
11 11 C2608 10uF
GND BST_CNTL 0.1uF C2606 0.1uF
GND 12 2 16V C2636 C2604 10V
GND 0.1uF 16V OPT TUNER I2C LPF
12 12 22uF 100pF +5V_TU
+B2[1.2V] 16V OPT L2609-*1
1.2V 1.2V 13 +B[5V] 10V 50V C C2611-*1
13 R2608 33
13 3 NON_TUNER_I2C_LPF 18pF R2625
+B3[3.3V] Q2600 B 10K
3.3V 3.3V 14 50V NON_TUNER_I2C_LPF 470 R2626
14 14 2SC3052 IF_AGC_SEL L2610-*1
RESET NC[RF_AGC] OPT 33 C2612-*1 82
RESET 15 4 R2600 0 OPT NON_TUNER_I2C_LPF TU_SIF
RESET E
18pF NON_TUNER_I2C_LPF
E
15 15 50V
IF/AGC OPT
IF_AGC_CNTL IF_AGC_CNTL 16 AS
16 16 5
DIF_1[N] B ISA1530AC1
DIF_1 DIF_1 17
17 17 R2622 Q2605
DIF_2[P] SCL +5V_TU C
L2609 270nH 4.7K
DIF_2 DIF_2 18 6 SCL0_3.3V
18 18
SDA TUNER_I2C_LPF
19 7 L2610 270nH R2643
19 19 SDA0_3.3V R2616 R2619
1K
SHIELD C2611 C2612 TUNER_I2C_LPF C2639 C2638 200 200
SHIELD SHIELD
NC(IF_TP) 62pF 62pF 20pF 20pF OPT
8 50V 50V 50V 50V
TUNER_I2C_LPF OPT
SIF C2602 TUNER_I2C_LPF TU_CVBS
9 close to TUNER TUNER_I2C_LPF TUNER_I2C_LPF R2644 0
E
0.1uF 16V R2613 0
NC
TU2600-*4 10 B
TU2600-*3 R2614 Q2602
TDTJ-S001D +1.2V_TU 1K ISA1530AC1
TDTJ-S031D VIDEO C
11 OPT
AU_Asia_Tuner_H
AU_Asia_Tuner_V close to TUNER L2605 +3.3V_TU
ANT_PWR[OPT] GND
ANT_PWR[OPT] 1 BLM18PG121SN1D +3.3V_TU
1 12
BST_CNTL
BST_CNTL 2
2 +B2[1.2V] C2600 C2603
+B C2634 C2607
+B 3 13 10uF 100pF 0.1uF C2605
3 50V 16V 100pF 0.1uF
NC[RF_AGC] 10V R2607
NC[RF_AGC] 4 +B3[3.3V] 50V 16V R2606 100K
4 14 100 TUNER_RESET
AS
AS 5 C2635
5 RESET C2610
SCL 10uF 0.1uF
SCL 6 15 10V 16V
6
SDA IF_AGC_CNTL
SDA 7
7 16
NC[IF_TP]
NC(IF_TP) 8 IF_AGC
8 DIF_1[N] R2601 0
SIF 17 R2611 100
SIF 9
9 NIM IF_N_EXT
NC DIF_2[P]
NC 10
10 18 R2612 100
VIDEO NIM
IF_P_EXT
VIDEO 11
11
GND
GND 12
12 19
1.2V
1.2V 13
13
3.3V SHIELD TU_IF_N_BCM
3.3V 14 INT_DEMOD R2603 0
14
RESET TU_IF_P_BCM
RESET 15 INT_DEMOD R2604 0
15
IF_AGC_CNTL
IF_AGC_CNTL 16
16
DIF_1
DIF_1 17
17
DIF_2
DIF_2 18
18
19
19
SHIELD
SHIELD
IF AGC FILTER CAUTION : Closed BCM IC(IC100)
A3.3V
+5V_NORMAL
5%
3.9K
R2633 R2638
1/16W
R2624
2K 220
TU_IF_AGC_BCM
1/16W 1/16W +3.3V_TU
510
5% 5% IC2600 +3.3V_NORMAL
5%
READY
3.9K
AZ1117H-ADJTRE1(EH11A) +3.3V_TU
0.01uF
1/16W
C2629
0.01uF
R2641
R2642 510
R2632
C2627
+1.2V_TU L2604
CIC21J501NE 60mA
R2628
INPUT ADJ/GND 10
3 1 C2621 C2622 C2625 C2633
TU_IF_AGC_1 R2 0.1uF 0.1uF 22uF 0.1uF
16V 16V 10V 16V
TU_IF_AGC_2
C2614
2 GND
R2627 For ESD
0.1uF 1.2K
16V OUTPUT +5V_NORMAL
R1
+5V_TU
IF FILTER OPTION R2629 L2603
V_OUT=V_REF(1+R2/R1) 200mA
1
BLM18PG121SN1D
C2616
0.1uF C2620 C2637 C2623 C2624 C2626
C2615 16V 0.1uF 0.1uF
0.1uF 10uF 22uF
10uF 16V 16V
16V 16V 10V
10V
TU_IF_N_BCM TU_IF_N_1
0.01uF C2631
TU_IF_P_BCM TU_IF_P_1
0.01uF C2632

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS GP2_BCM Ver. 1.0
Tuner (Half Nim) 28
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
PANASONIC (ISDB-T)
MN884433
ISDB_DEMOD
+1.2V_DE +3.3V_DE R2807 22
FE_TS_VAL_ERR
ISDB_DEMOD ISDB_DEMOD ISDB_DEMOD
ISDB_DEMOD ISDB_DEMOD ISDB_DEMOD R2808 22
C2812 C2815 C2816 C2819 C2821 FE_TS_SYNC
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
16V 16V 16V 16V 16V ISDB_DEMOD
R2809 22
FE_TS_SERIAL
ISDB_DEMOD (FE_TS_SERIAL)
ISDB_DEMOD
C2810 R2810 22
0.1uF FE_TS_DATA_CLK
16V
+3.3V_DE
AGC_S
VDDH_5
GPO2
DENB
PCKB
SDOB
TEST0
SCKB
VDDL_7
VSS_11
HDVDDL1
NC_4
HDVDDH
NC_3
RON
HDVPP
VSS_10
VDDH_4
DENA
PCKA
SDOA
GPI2
SCKA
TEST2
TEST1
OPT OPT AMP_I2C HAVE PULL-UP
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
100
VSS_1 1 75 VSS_9 R2811 R2812
AVDD_S 2 74 INTB 2.2K 2.2K
C2802 0.1uF AII_S 3 73 INTA
ISDB_DEMOD AIQ_S SADR
4 72
AVSS_S VDDH_3 ISDB_DEMOD
5 71
VRT_S SCL C2825 0.1uF
6 70 SCL1_3.3V
VRB_S SDA R2813 22
7 69 SDA1_3.3V
TCPO_S VSS_8 R2814 22
8 68
VDDL_1 IC2800 HDVDDL0 ISDB_DEMOD
9 67
MSCL_S SADR_S C2826 0.1uF
C2803 0.1uF ISDB_DEMOD 10 66
ISDB_DEMOD R2801 2.2K MSDA_S MN884433 NC_2
11 65
R2802 2.2K VSS_2 SADR_T
ISDB_DEMOD 12 64
VSSH VDDL_6 ISDB_DEMOD
13 63
C2804 0.1uF ISDB_DEMOD PSEL ISDB_DEMOD VSS_7 C2827 0.1uF
14 62
ZSEL 15 61 ERRB
VDDL_2 16 60 SYNCB
C2805 0.1uF ISDB_DEMOD ACKI ERRA
17 59
ISDB_DEMOD TCPO_T SYNCA
R2800 18 58
10K 1% IR_T TDO
19 57
VRT_T 20 56 CSEL1
C2806 0.1uF ISDB_DEMOD VRB_T CSEL0
21 55
C2807 0.1uF ISDB_DEMOD AVDD_T TMS
ISDB_DEMOD 22 54
C2808 0.1uF ISDB_DEMOD AIN_T TRST
IF_N_EXT 23 53 ISDB_DEMOD
C2800 0.1uF AIP_T VDDL_5
24 52
IF_P_EXT C2801 0.1uF AVSS_T VSS_6 C2824 0.1uF
ISDB_DEMOD 25 51
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
XO
XI
TCK
TDI
GPO1
GPO0
GPI1
GPI0
NC_1
NRST
VSS_3
VSS_4
TEST4
SHVPP
VSS_5
TEST3
MSCL_T
MSDA_T
VDDH_1
AGCI_T
AGCR_T
VDDL_3
VDDH_2
SHVDDH
VDDL_4
ISDB_DEMOD
R2804 2.2K DEMOD_RESET
ISDB_DEMOD
R2805 2.2K
ISDB_DEMOD
ISDB_DEMOD C2813 ISDB_DEMOD
C2811 0.1uF C2823
0.1uF 0.1uF
16V 16V 16V
C2817 C2820 C2822

0.1uF 0.1uF 0.1uF
16V 16V 16V
ISDB_DEMOD ISDB_DEMOD
ISDB_DEMOD
R2803 10K
IF_AGC_ISDB ISDB_DEMOD ISDB_OPT
ISDB_DEMOD R2806
1M
C2809
0.1uF
ISDB_DEMOD
X2800 ISDB_DEMOD
ISDB_DEMOD
25MHz C2818
C2814
15pF 15pF
50V 50V

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS GP2_Saturn7M Ver. 1.0
ISDB-T Demodulator 28
Panasonic Demodulator Power(3.3V,1.2V)
ISDB_POWER
IC2900
SC4215ISTRT
+3.3V_DE
+3.3V_NORMAL +3.3V_DE NC_1 GND
1 8 +1.2V_DE
ISDB_POWER ISDB_POWER
EN ADJ R2903
L2900 2 7
BLM18PG121SN1D
5.1K
VIN VO
ISDB_POWER ISDB_POWER 3 6
ISDB_POWER ISDB_POWER
C2902 C2903
C2900 C2901 0.1uF 10uF ISDB_POWER ISDB_POWER
16V NC_2 NC_3
10V 4 5 C2904 C2905
0.1uF
0.1uF 0.1uF 16V 22uF
16V
10K
R2902
ISDB_POWER
IF AGC SELECTION
IF_AGC_ISDB TP2901 IF_AGC_SEL
R2900
0
ISDB_DEMOD
IF_AGC
R2901
0
INT_DEMOD
TU_IF_AGC_BCM

Demodulator
USB2 OPTION
+3.3V_NORMAL
USB / DVR Ready
IC2202
AP2191SG-13 +5V_USB
R2220
L2202 NC 8 4.7K
1 GND
MLB-201209-0120P-N2 OPT
OUT_2 7 2 IN_1
120-ohm OUT_1 6 3 IN_2
C2218 C2220
FLG 5 C2222
4 EN 10uF
100uF R2226 0.1uF
EAN60921001 2.7K 10V
16V
USB_CTL1
KJA-UB-4-0004
C2206
1uF
10V
JK2201
SIDE_USB_DP
SIDE_USB_DM
R2225 0 /USB_OCD1
C2207
0.1uF
2
USB_DM1
C2208
15pF
C2210
15pF
3
USB_DP1
R2202
USB DOWN STREAM

1M 1%
4
D2201 D2203
CDS3C05HDMI1 CDS3C05HDMI1
5
5.6V 5.6V
X2201
+3.3V_NORMAL +3.3V_USB 24MHz
R2203
100K
R2201
12K
1/10W 1%
L2201
BLM18PG121SN1D
+3.3V_USB
VSS
VDD33PLL
RBIAS
VDD18PLL
XTAL1/CLKIN
XTAL2
USBUP_DP
USBUP_DM
VDDA33_3
SUSP_IND/LOCAL_PWR/NON_REM0
C2212
36
35
34
33
32
31
30
29
28
USBDN1_DM VBUS_DET 0.1uF R2209
USB_DM1 1 27 100K
+3.3V_USB R2214
THERMAL OPT 0
USBDN1_DP 2 26 RESET_N
USB_DP1 37 /RST_HUB
R2210 C2215 USB +3.3V_NORMAL
USBDN2_DM 3 25 HS_IND/CFG_SEL1
USB_DM2 100K 0.1uF +3.3V_USB
USBDN2_DP SCL/SMBCLK/CFG_SEL0 OPT
USB_DP2 4 24
IC2201
VDDA33_1 VDD33 R2212 100K OPT IC2203
5 USB2512A_AEZG 23 AP2191SG-13 +5V_USB
R2221
C2201 NC_1 SDA/SMBDATA/NON_REM1 R2211 100K OPT L2203 NC 8 4.7K
C2202 C2203 C2204 C2205 6 22 1 GND
1uF MLB-201209-0120P-N2 OPT
10V 0.1uF 0.1uF 0.1uF 0.1uF NC_2 NC_8 OUT_2 7 2 IN_1
7 21
R2213 100K OPT
120-ohm OUT_1 6 3 IN_2
NC_3 8 20 NC_7 C2221
C2219 C2223
0 R2207 OPT FLG 5 4 EN 10uF
NC_4 NC_6 SCL2_3.3V 100uF R2223 0.1uF
9 19 EAN60921001 2.7K 10V
0 R2208 OPT KJA-UB-4-0004 16V
SDA2_3.3V JK2202
10
11
12
13
14
15
16
17
18
USB_CTL2
1
R2204
100K
R2205
100K
100K
+3.3V_USB R2227 0 /USB_OCD2
R2206
TEST
NC_5
040:J6
VDD18
OCS1_N
OCS2_N
PRTPWR1
VDD33CR
PRTPWR2
2
USB_DM2
VDDA33_2
3
C2213 C2214 USB_DP2

4.7uF
0.1uF
C2211
0.1uF
USB DOWN STREAM
4
D2202 D2204
CDS3C05HDMI1 CDS3C05HDMI1
5
5.6V 5.6V
1uF
10V
C2209
USB_CTL2
USB_CTL1
/USB_OCD1
/USB_OCD2
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
USB
BLUETOOTH +3.3V_NORMAL
G
BCM BT MODULE
D
C1898
Q1801
1uF
10
R1889
RTR030P02
BCM BT MODULER1886 BCM BT MODULE
BCM BT MODULE
BLUETOOTH FOR BCM R1887 47K
BCM BT MODULE
47K
R1888 C
BT_ON/OFF 4.7K B
2SC3052
OPT
500
L1899
BCM BT MODULE Q1800
E
BCM BT MODULE
11
10
BCM BT MODULE
C1899
22uF
9 10V
R1896
27
BT_DM
8
D1899 BCM BT MODULE
CDS3C05HDMI1
7 5.6V
BCM BT MODULE R1897
27
BT_DP
6 D1898
CDS3C05HDMI1BCM BT MODULE
5.6V
5 BCM BT MODULE
R1898
0
BT_RESET
4
BCM BT MODULE
3
R1899
0
VREG_CTRL
2
BCM BT MODULE
12507WR-10L
P1895
BCM BT MODULE

Bluetooth
CI POWER ENABLE CONTROL
CI CONTROL BUFFER
/CI_SEL CI_A[0]
CI_A[1]
EBI_CS CI_A[2]
CI_A[3]
EBI_WE
CI_A[4]
CI_5V_CTL
CI_A[5]
CI_A[6] 007:H7 [GP27]
CI_A[7]
CI_A[8]
CI_A[9]
CI_A[10]
CI_A[11]
CI_A[12]
CI_A[13]
CI_A[0-13] 007:E6 EBI_RW
CI_A[14]
/CI_CD1
CI_OUTCLK,CI_OUTDATA[0-7],CI_OUTSTART,CI_OUTVALID
CI_OUTDATA[4]
CI_OUTDATA[5]
CI_OUTDATA[6] DVB-CI PULL-DOWN (Near CI Slot)
CI_OUTDATA[7]
CI_OUTCLK
CI_OUTVALID
CI_OUTSTART
/CI_IREQ CI_OUTDATA[0]
[GP39] CI_OUTDATA[1]
007:H5;016:AJ3
CI_OUTDATA[2]
CI_OUTDATA[3]
DVB-CI PULL-UP (Near CI Slot)
CI_MOD_RESET [GP49]
/CI_WAIT
/CI_WAIT
CI_OUTCLK
/CI_CD1
/CI_CD2 [GP38]
/CI_CD2
CI_MOD_RESET
FE_TS_SYNC
FE_TS_VAL_ERR
FE_TS_DATA_CLK

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS High_Common(BCM3556) 2009.10.19
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. Non_CI 46
Mini LVDS
[Right FFC Connector]

(60Pin Mini-LVDS)
[LEFT FFC Connector]

P7401
(60Pin Mini-LVDS)
104060-6017
0 NON_GIP
0 NON_GIP
0 NON_GIP
0 NON_GIP
0 NON_GIP
0 NON_GIP
P7400 MINI_LVDS
104060-6017
MINI_LVDS
1 GND
R7405
R7406
R7407
R7408
R7410
R7411
VGH_M
2 Z_OUT R7412 0 MINI_LVDS Z_OUT (+25V)
1 GND 3 CLK1 CLK1
2 GMA1 4 CLK2 CLK2
GMA1 JP8806
3 GMA3 5 CLK3 CLK3
GMA3 R7414 0 NON_GIP GSC/GCLK3_I
4 GMA4 6 CLK4 CLK4
GMA4 R7415 0 NON_GIP GOE/GCLK1_I
5 GMA6 7 CLK5 CLK5
GMA6
6 GMA7 8 CLK6 CLK6
GMA7 R7416 0 NON_GIP
7 GMA9 9 VGI_N VGI_N VGL
10 VGI_P (-5V)
8 GMA10 GMA10 VGI_P VGL_I
9 GMA12 11 VGH_ODD VDD_ODD
GMA12 JP8808
12 VGH_EVEN JP8807
10 GMA13 GMA13 VCC_LCM VDD_EVEN R7418 0 NON_GIP
11 GMA15 13 VSS R7409 0 GIP
12 GMA16 14 VST VST
GMA16 JP8804
13 GMA18 R7402 15 GND
GMA18
14 GND 3.3K 16 VCOM_FB VCOMRFB
MINI_LVDS 17 VCOM_IN
15 OPT_N VCOMR
18 GND VDD_LCM
16 H_CONV H_CONV
17 VST_IN 19 VDD To reduce
GSP/GVST_I Audible Noise
18 POL 20 VDD
POL C7408
19 SOE 21 HALF_VDD C7406
SOE 1uF 0.1uF
20 GND VCC_LCM 22 HALF_VDD 50V 50V
23 GND MINI_LVDS
21 LV0+ RXD1-
24 VCC MINI_LVDS
22 LV0- RXD1+
23 LV1+ 25 VCC
RXD0- HVDD
24 LV1- C7400 C7402 26 GND
RXD0+ 0.1uF 0.01uF
25 LV2+ 27 RV0+ RXA1-
RXC4- 16V 50V
26 LV2- MINI_LVDS MINI_LVDS 28 RV0- RXA1+
RXC4+ C7409
27 LVCLK+ 29 RV1+ RXA0-
RXC3- 10uF
28 LVCLK- VDD_LCM 30 RV1- RXA0+ 16V
RXC3+ VCC_LCM
HVDD To reduce 31 RV2+ MINI_LVDS
29 LV3+ RXC2- RXB4-
Audible Noise 32 RV2-
30 LV3- RXC2+ JP8805 RXB4+
2012 33 RVCLK+
31 LV4+ RXC1- RXB3-
C7401 C7404 34 RVCLK- C7405 C7407
32 LV4- RXC1+ C7403 RXB3+ 0.1uF 0.01uF
10uF 1uF 0.1uF 35 RV3+
33 LV5+ RXC0- 16V 50V 50V RXB2- 16V 50V
MINI_LVDS MINI_LVDS 36 RV3- MINI_LVDS MINI_LVDS
34 LV5- RXC0+ RXB2+
35 GND MINI_LVDS 37 RV4+ RXB1-
36 VCC 38 RV4- RXB1+
37 VCC 39 RV5+ RXB0-
38 GND 40 RV5- RXB0+
39 HALF_VDD 41 GND VCC_LCM
40 HALF_VDD 42 SOE SOE
41 VDD 43 POL POL
42 VDD VGL 44 VST_IN GSP/GVST_I R7413
43 GND (-5V) 45 H_CONV H_CONV 3.3K
VGL_I MINI_LVDS
44 VCOM_IN 46 OPT_N
VCOML
45 VCOM_FB 47 GND
VCOMLFB
46 GND 48 GMA18 GMA18
47 VST 49 GMA16 GMA16
VST R7403 0 NON_GIP
48 VSS R7401 0 GIP 50 GMA15 GMA15
49 VGH_EVEN 51 GMA13 GMA13
VDD_EVEN
50 VGH_ODD 52 GMA12 GMA12
VDD_ODD
51 VGI_P 53 GMA10 GMA10
VGI_P
52 VGI_N 54 GMA9 GMA9
VGI_N
53 CLK6 55 GMA7 GMA7
CLK6
CLK5
CLK4 VCC_LCM
CLK3
57 CLK2 R7400 0 GIP 59 GMA1 GMA1
CLK2 R7404
58 CLK1 3.3K 60 GND
CLK1
59 Z_OUT NON_GIP
Z_OUT
60 GND 61
.
61

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS COMMON 09/10/xx
URSA3 120Hz MINI_LVDS 74
LVDS
[51Pin LVDS Connector]

(For FHD 60/120Hz) [41Pin LVDS Connector]
(For FHD 120Hz)
PANEL_VCC
JP8809
L7700
500
FHD_120Hz
P7700
TF05-51S
FHD_120Hz
C7700 C7701 C7702
10uF 1000pF 0.1uF P7701
25V 50V 50V
1 OPT TF05-41S
FHD_120Hz
2
3
1
4
2
5
3 RXD4-
6
4 RXD4+
7
5 RXD3-
8
6 RXD3+
9 R7700 0
7
NON_LGD_22
10 R7701 0
8 RXDCK-
NON_LGD_22
11 RXA4- 9 RXDCK+
12 RXA4+ 10
13 RXA3- 11 RXD2-
14 RXA3+ 12 RXD2+
15
13 RXD1-
16 RXACK- 14 RXD1+
17 RXACK+ 15 RXD0-
18
16 RXD0+
19 RXA2- 17
20 RXA2+ 18
21 RXA1- 19 RXC4-
22 RXA1+ 20 RXC4+
23 RXA0- 21 RXC3-
24 RXA0+ 22 RXC3+
25
23
BIT_SEL
26 R7710 24 RXCCK-
10K 10BIT OPEN
27 RXB4- 8BIT 25 RXCCK+
8BIT GND
28 RXB4+ 26
29 RXB3- 27 RXC2-
30 RXB3+ 28 RXC2+
31
29 RXC1-
32 RXBCK- 30 RXC1+
33 RXBCK+ 31 RXC0-
34
32 RXC0+
35 RXB2- 33
36 RXB2+ 34
37 RXB1- 35
38 RXB1+ 36
39 RXB0- R7708-*1 0 37
40 RXB0+ FHD_OPC 38
41 NON_SCAN R7706 0 SCAN_BLK2 39
R7702 0 LD60_SCAN
42 R7707 0 +3.3V_NORMAL
OPC_EN 40
FHD_OPC
43 R7708 0 SCAN_BLK1/OPC_OUT 41
LD60_SCAN R7711
44 R7709 0 PWM_DIM
FHD_OPC 3.3K
42
45 JEIDA
46 R7703 33 FRC_RESET R7712

240Hz 10K
47 R7704 33 SCL3_3.3V VESA
240Hz
48 R7705 33 SDA3_3.3V
240Hz
49
LVDS_SEL
50 HIGH JEIDA
51 GND(NC) VESA
52
TP7700 OPC_OUT

URSA3 120Hz LVDS
FROM LIPS & POWER B/D
L_VS
R_VS
MO_SCLK
+3.5V_ST
RT1P141C-T112 M2_SCLK
15V-->3.6V +12V +3.5V_ST
Q8002 MO_MOSI
20V-->3.5V R8068 +3.5V_ST
M2_MOSI
24V-->3.48V 100K
R8004 1 3
4.7K +24V 12V-->3.58V
NORMAL_26~52 IC8007
R8075
10K
OPT
R8000 C P8000 ST_3.5V-->3.5V
R8067
14K
1%
2
R8063
12K
1%
RL_ON 10K FW20020-24S NCP803SN293
PD_+12V
PD_+3.5V
B Q8000 +5V_NORMAL
2SC3052 R8081 POWER_DET
VCC RESET 100
L8005 400Hz_VSYNC/42_47_LOCAL DIMMING 3 2
E PWR ON 1 24V
2 MLB-201209-0120P-N2 R8078 +12V MAX 350mA +5V_NORMAL Power_DET 1
24V 3 4 24V C8024 0 IC8003
68uF GND
+3.5V_ST GND 5 6 GND R_VS
AOZ1072AI
L8003 C8018 35V ESD
R8064
5.1K
1/16W
5%
GND 7 8 GND
MLB-201209-0120P-N2 0.1uF L8010 C8065
NON_PD_+3.5V
3.5V 3.5V 400Hz_VSYNC L8007
9 10 50V PGND LX_2 3.6uH 0.1uF
R8036 1 8 16V
3.5V 11 12 3.5V 0 L_VS CIC21J501NE
C8000 C8004 C8006
100uF GND 13 14 GND NR8040T3R6N
0.1uF 0.1uF
16V GND GND/V-sync R8082 0 V_SYNC 400Hz_MO_SCLK/42_47_LOCAL DIMMING VIN LX_1
16V 16V 15 16 2 7
R8077 0
1%
12V 17 18 INV ON 400Hz_VSYNC M2_SCLK C8068
R8053
47K
R8028 0 0.1uF R8079
12V 19 20 A.DIM POWER_ON/OFF2_2 +3.5V_ST +24V 100K
MO_SCLK 16V AGND 2A EN C8047 C8066 C8049 not to RESET at 8kV ESD
+12V 12V P.DIM1 400Hz_MO_SCLK 3 6 R1
21 22 22uF 10uF 0.1uF
R8050
1%
L8002 GND/P.DIM2 Err OUT C8028 C8030 10V 16V 16V IC8008
5.6K
MLB-201209-0120P-N2 23 24 10uF 10uF 10K
POWER 18.5V
R8054
FB COMP OPT POWER 24V POWER 20V NCP803SN293
SLIM_32~52 +3.3V_NORMAL 25V 25V 4 5 R8061-*2
OPT R8080 R8061-*1 R8061
C8003 C8005 NON_CMO R8026 22K 1% 24K 1% R8074
C8001 25 R8019 12K C8046 14K 1% 24K 1%
0.1uF 0.1uF 1K 2200pF 100
0
0
100uF VCC RESET
0
50V 100 R8049 100pF 3 2
SMAW200-H24S2
LD
50V C8040
R8015
0
25V 50V
R8085
0
R8018 POWER 18.5V 1
P8001 POWER 24V POWER 20V
SCAN_LIPS
100 C R8062-*2 GND
OPT
R8062-*1 R8062
C8011
0.1uF
16V
R8023 R8032 4.7K 1%
CMO_PSU 10K INV_CTL 4.3K 1% 5.1K 5%
1%
B
400Hz_MD_MDSI
6.8K
R8005
R8076
R8007
R8055
10K
R2
NON_SCAN_LIPS
OPT Q8005 Vout=0.8*(1+R1/R2)
R8009
0
SCAN
0
E 2SC3052 R8039
10K
R8029 OPT
CMO_PSU
0
R8030
AUO_PSU
OPT
0
C8012
1uF
25V
R8014
MO_MOSI
M2_MOSI
R8031 0 A_DIM
SHARP_PSU_26_32_52
0
400Hz_MD_MDSI/42_47_LOCAL DIMMING
LGD_IOP A_DIM_LGD BCM core 1.2V volt
R8084 R8021
<OS MODULE PIN MAP> 0 AUO_PSU/SHARP_PSU_60 R8027
SCAN_BLK2
R8022 0
SCAN_PSU
R8083
0 0 PWM_NON_OPC PWM_DIM R8044
SCAN_PSU MAX 3.1A
PIN No LGD CMO(09) AUO SHARP R8020 R8033 10K
NON_SCAN_PSU C8017 C8021 0 POWER_ON/OFF2_1
OPT
SCAN_BLK1/OPC_OUT
0
+3.3V_NORMAL
3.9K
1uF
R8047
0.1uF SCAN/FHD_OPC ESD +12V
OPT 25V EP ESD
INV_ON A-DIM INV_ON INV_ON R8034 D8000 MAX 2.3A
18 OPT 5.6V R8045-*1 A1.2V
0 100K D1.2V
OPC_OUT
HD_OPC AGND FB R8045
V4:VBR-A 1 14
20 NC Err_out Err_out R8035 0
V5:NC 0 +3.3V_NORMAL NON_ESD R8060
SS EN/SYNC
15
2 13 R8043 R8046 R8048 POWER_ON/OFF2_2
+3.3V_NORMAL D3.3V
THERMAL
C8026 L8013 10K
22 PWM_DIM PWM_DIM A-DIM PWM_DIM R8024 470K 30K 910K
0 0.1uF PGND_1 PGND_2 CIC21J501NE
3 12
R8037
4.7K
AUO_PSU/SHARP_PSU_52_60 ERROR_OUT L8009 1% 1% 1%
IC8001 L8011
OPT
3.9K
2uH R1 R2
R8066
SW_1 SW_2 BLM18PG121SN1D

L8016
Err_out INV_ON PWM_DIM
24 GND R8025 4 11 L8015
NON_LED_MODEL
0 C8069 VIN 3.6uH CIC21J501NE
NON_LED_MODEL 0.1uF
IN_1 IN_2
2
NON_LED_MODEL 5 10 C8036
0.1uF EN 6
+3.5V_ST NC POK R8040
1%
6 9
R8069
27K
100K FB IC8005 LX
R8041 C8037 C8041 C8043 C8045 4 7
BS VCC R8042
7 8 22uF 22uF 10uF 0.1uF C8063 C8064
0 C8051 C8057 C8059 C8067
1%
10 10V 10V 16V 16V C8052 COMP AOZ1024DI 22uF 22uF 0.1uF 0.1uF
4.7K
MP2208DL-LF-Z 0.1uF 22uF 5 10uF 16V 16V

R8070
10V 10V
50V 25V 10V
R8058
3
1
20K
L8006
+12V
PANEL_POWER C8054
L8000 2200pF
AGND
PGND
MLB-201209-0120P-N2
CIC21J501NE 50V
1%
R8071
10K
C8029 C8032 C8033 C8035

C8027 1uF
22uF 0.1uF 22uF
0.1uF 10V
C8009 C8010 16V
C8008
0.1uF 10uF
0.01uF 25V
25V 50V Vout=0.8*(1+R1/R2)
OPT Q8004
AO3407A
S
D
C8013 PANEL_VCC
R8010
10K
4.7uF
G
50V OPT
R8003 C8015
22K 1uF
25V
R8011
1.8K
OPT C
R8002
10K B Q8003
2SC3052
C C8022
R8001 R8008 E 0.1uF
47K B Q8001 22K 50V Max 1100 mA
PANEL_CTL BCM DDR 1.8V
2SC3052 +3.3V_NORMAL
1:AK10 A2.5V
E +3.5V_ST A2.5V
D1.8V
Vout=0.9*(1+R1/R2) IC8004
L8012 SC4215ISTRT
Replaced Part 3.6uH VOUT : 2.533V
500
NR8040T3R6N 1 8
L8014
IC8002
500
L8017
MP2108DQ NC_1 GND R8073

R8059 18K R2
10K 2 7 1%
10K
L8008
C8034
0.01uF
25V
BST RUN R8052 EN ADJ R8072
1 10 POWER_ON/OFF1 39K R1
3 6 1%
CIC21J501NE
VO
+12V
+5V_USB VIN
2 9
VREF
C8053 VIN
10uF C8055 4 5
+5V_USB 3A C8042 OPT C8058 C8061 C8062
0.1uF
LX COMP 0.01uF OPT
16V C8056 NC_2 NC_3
MAX 1500mA Placed on SMD-TOP 3 8 50V
10uF 10uF 0.1uF
IC8000 25V 0.1uF
100pF R1 16V 16V
MP8706EN-C247-LF-Z PGND FB C8044 R8057 Placed on SMD-TOP
4 7
C8031
500
C IN 22uF C8039 R2 10K
L8001
IN GND 10V 1%
1 8 SGND SS 3300pF
OPT 5 6 R8056
C8014 50V C8048 C8050
C8016 10K
1uF OPT 22uF 0.1uF
1%
SW_1 VCC 100pF C8038 1/10W
R8016
33K
2 7 50V C8019 R8051 1% 10V
50V 0.01uF
C8002 100pF C8020 C8023 C8025 6.8K
10uF R8012 R1 22uF 0.1uF 0.1uF 25V
SW_2 3A FB 10K 50V Vout=0.8*(1+R1/R2)
25V 3 6 10V 16V 16V
C8007
0.1uF POWER_ON/OFF2_1
BST EN/SYNC
4 5
1%
R8017
6.2K
R8006 R8013
22 10K
R2
L8004
3.6uH +5V_USB
NR8040T3R6N
Vout=(1+R1/R2)*0.8

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS BCM (EUROBBTV)
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. POWER 15
FLMD0
GND
+3.5V_ST
10K
0
47K
50V 50V MICOM_DOWNLOAD
15pF 15pF R8146
OPT
C8101 C8102
R8143
R8140
10MHz
X8100
X8101-*1
15pF
15pF
0
32.768KHz
R8138
R8139 MICOM_EPSON
10K
C8106
C8105
MICOM_KDS
OPT X8101
+3.5V_ST
32.768KHz
MICOM_RESET
WIRELESS_DETECT
WIRELESS_PWR_EN
R8175
10Mhz Crystal Ready

4.7M
22
47K
+3.5V_ST
for Debugger GND SW8100
R8180
R8184
JTP-1127WEM
P8100
2 1
+3.5V_ST
22
12505WS-12A00 C8103
0.1uF C8108
0.1uF 4 3
1
0.1uF
MICOM_RESET
R8178
3 R8113 22
NEC_ISP_Tx
+3.5V_ST
4
C8104
5 R8115 22 NEC_ISP_Rx
6
R8186 20K
7 R8116 22 1/16W
OCD1A 1%
8
9 R8118 22 EDID_WP
OCD1B C
R8185
20K
1/16W
1%
10
VDD
VSS
REGC
P121/X1/OCD0A
P122/X2/EXCLK/OCD0B
FLMD0
P123/XT1
P124/XT2/EXCLKS
RESET
P40
P41
P120/INTP0/EXLVI
B Q8100
11 R8119 22 2SC3052
FLMD0
12
E
13
R8104 10K
48
47
46
45
44
43
42
41
40
39
38
37
R8127 22
P60/SCL0 1 36 P140/PCL/INTP6 R8187 22
SCL1_3.3V RL_ON
R8128 22
P61/SDA0 2 35 P00/TI000 R8188 22
SDA1_3.3V SCART1_MUTE
+3.5V_ST +3.5V_ST P62/EXSCL0 P01/TI010/TO00 R8189 10K
R8108 10K NEC_EEPROM_SCL 3 34
NEC_ISP_Tx
P63 P130 R8192 22
OPT NEC_EEPROM_SDA
4 33 WIRELESS_SW_CTRL
R8105 10K
NEC_ISP_Rx R8126 IC8101
R8129 22 P33/TI51/TO51/INTP4 P20/ANI0 R8194 22
5 32 FLASH_WP
10K HDMI_CEC
R8106 10K R8130 22 P75 ANI1/P21
OCD1A 6 UPD78F0513AGA-GAM-AX 31 R8195 22
POWER_ON/OFF2_1 MODEL1_OPT_3
R8107 10K R8131 22 P74 ANI2/P22 R8196 22

OCD1B AMP_MUTE 7 30 MODEL1_OPT_2
R8132 22 P73/KR3 NEC_MICOM ANI3/P23
8 29 R8190 22
MODEL1_OPT_0 POWER_ON/OFF1
R8133 22 P72/KR2 ANI4/P24 R8193 22
SOC_RESET
9 28 MICOM_DOWNLOAD
R8134 22 P71/KR1 ANI5/P25 R8191 22
INV_CTL
10 27 SIDE_HP_MUTE
EEPROM for Micom R8135 22 P70/KR0 ANI6/P26
+3.5V_ST MODEL1_OPT_1 11 26 KEY2
R8136 22 P32/INTP3/OCD1B ANI7/P27
OCD1B
12 25 KEY1
IC8100 NON_M-REMOTE
M24C16-WMN6T
13
14
15
16
17
18
19
20
21
22
23
24
NC/E0 VCC
1 8
47K
NC/E1 WC
R8100
2 7
C8100
0.1uF
AVSS
+3.5V_ST
AVREF
NC/E2 SCL
R8122 4.7K
R8117
R8125 4.7K
3 6 NEC_EEPROM_SCL
22
P15/TOH0
P14/RXD6
P13/TXD6
P12/SO10
VSS SDA R8114

4 5 NEC_EEPROM_SDA
P30/INTP1
22
FOR ATSC Assy

P17/TI50/TO50
P11/SL10/RXD0
SCART1_MUTE TP8100
P16/TOH1/INTP5
P10/SCK10/TXD0
C8107 1uF
P31/INTP2/OCD1A
22
22
+3.5V_ST
R8181 10K
+3.5V_ST
R8179
OPT
R8177
MICOM MODEL OPTION

R8182 10K
OPT
10K
10K
10K
10K
22 NON_M-REMOTE
22
22
22
MODEL OPTION
PDP/3D
PIN NAME
TACT_KEY
OLED/3D
PIN NO. HIGH LOW
TOUCH_KEY
LOGO_BUZZ
R8109
R8111
R8120
R8123
R8142
R8144
R8145
R8176
R8102 100 MODEL_OPT_0 8 OLED/3D

AMP_RESET_N MODEL1_OPT_0 LCD/PDP R8183 10K
R8103 100 OPT
PANEL_CTL MODEL1_OPT_1
R8101 100 MODEL_OPT_1 11 LOGO_BUZZ PWM_LED
OPC_EN MODEL1_OPT_2
OPC
MODEL1_OPT_3
MODEL_OPT_2 30 TOUCH_KEY TACT_KEY
IR
10K
10K
10K
10K
MODEL_OPT_3 31 PDP/3D LCD/OLED
OCD1A
NEC_RXD
NEC_TXD
POWER_DET
PWM_LED
LCD/PDP
LCD/OLED
TACT_KEY
LED_R/BUZZ
NEC_ISP_Rx
NEC_ISP_Tx
LCD PDP OLED 3D
R8110
R8112
R8121
R8124
LED_B/LG_LOGO
MODEL_OPT_0 0 0 1 1
POWER_ON/OFF2_2
MODEL_OPT_3 0 1 0 1
LOW LOW_SMALL TBD HIGH
MODEL_OPT_1 0 0 1 1
MODEL_OPT_2 0 1 0 1

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. MICOM 5
+3.5V_ST
EYEQ
R8225
100 D8204
IR & KEY NEC_EEPROM_SCL P8200
CDS3C05HDMI1
R8213 5.6V 12507WR-12L
R8211
10K 10K C8213
1% 1% 1000pF
50V
L8200 OPT
R8209 BLM18PG121SN1D 1
100 EYEQ
KEY1 R8226
L8201 100
R8210 D8201 2
100 BLM18PG121SN1D NEC_EEPROM_SDA
5.6V D8205
KEY2 C8214
AMOTECH CDS3C05HDMI1
C8206 C8207 1000pF
50V 5.6V 3
0.1uF 0.1uF
D8200 OPT
5.6V
AMOTECH 4
+3.5V_ST
+3.5V_ST 5
L8202
BLM18PG121SN1D
+3.5V_ST 6
R8202
47K
R8200
22 +3.5V_ST R8227 1.5K
IR R8204 C8208 C8209 7
0.1uF 1000pF LED_B/LG_LOGO
47K 16V 50V TACT_KEY R8287
R8203
Q8200 C 10K 10K
B R8206 8
2SC3052 LD650/LD750
E 3.3K
R8205 OPT R8224
C 47K 100
B 9
Q8201 E D8206
2SC3052 C8212 5.6V
100pF AMOTECH
+3.5V_ST +3.3V_NORMAL 50V 10
COMMERCIAL L8203
BLM18PG121SN1D
R8201 +3.5V_ST 11
0 R8214
47K
OPT R8207 COMMERCIAL_EU R8276
22 LED_R/BUZZ 12
IR_OUT R8218 C8211
C8210 1.5K
COMMERCIAL 47K 1000pF OPT
0.1uF
R8216 COMMERCIAL 16V 50V R8280 13
Q8202 C 10K 10K
2SC3052 B
COMMERCIAL_EU E R8220
COMMERCIAL_EU C 47K
B ETHERNET CONNECT
Q8204 COMMERCIAL A2.5V
E
2SC3052
COMMERCIAL
L8204
JK8200
CIC21J501NE
R8212 XRJV-01V-D12-180
0
COMMERCIAL_US R8283
0
EPHY_TDP 1
Zener Diode is OPT
C8218
10pF 2
50V
+3.5V_ST
close to wafer R8284
5.6V
D8207
WIRELESS 0
3
EPHY_TDN OPT
C8220
+3.5V_ST R8285 10pF
R8215 0 50V
EPHY_RDP 4
47K
R8208 WIRELESS OPT C8216
22
IR_PASS R8219 C8221 1000pF
47K 10pF 50V 5
D8212
5.6V
WIRELESS 50V
D8208
5.6V
R8217 WIRELESS
Q8203 C 10K R8286
B 0
2SC3052 6
E WIRELESS EPHY_RDN
WIRELESS R8221
C 47K
OPT
B C8222 C8217 7
D8209
5.6V
Q8205 E WIRELESS 10pF

2SC3052 50V 1000pF
WIRELESS
8
D3.3V
R8281 510
D1
D2
EPHY_LINK
R8282 510
D3
D8210
5.6V
EPHY_ACTIVITY D4
9
D8211
5.6V
RS232C
Trace impedance : 100 ohm differenctial impedance to GND plane
10 5 mils trace width with 7 mils air gap on P/N pair.
+3.5V_ST 5
Adjacent TX/RX differential pairs should be separated by more than
15 mils to each other
9
OPT
IR_OUT 4
R8279
0
R8277 8
100
C8200 0.33uF 3
IC8200 7
C8205 R8278
MAX3232CDR 0.1uF 100
2
D8202 D8203 6
C1+ VCC
1 16 CDS3C30GTH CDS3C30GTH
30V 30V 1
C8201
0.1uF V+ GND
2 15
+3.5V_ST
C8202 SPG09-DB-009
0.1uF C1- DOUT1 JK8201
3 14
R8222 R8223
C2+ RIN1 4.7K 4.7K
4 13 OPT OPT
C8203
0.1uF C2- ROUT1 R8273 0
5 12 BCM_RXD1
R8274 0
V- DIN1 NEC_RXD
6 11
C8204
0.1uF DOUT2 DIN2
7 10 R8272 0
BCM_TXD1
RIN2 ROUT2
8 9 R8275 0
NEC_TXD
EAN41348201

* HDMI CEC
E E +3.3V_HDMI
+3.3V_NORMAL
JACK_GND
D8302 KRC104S D8308 KRC104S HDMI_HPD_4
HDMI_HPD_1 L8300
5.5V Q8305 B 5.5V GND Q8307 B
GND E E R8321 BLM18PG121SN1D
OPT R8311 GND ESD 5V_HPD4
SHIELD C 4.7K 5V_HPD1 C 4.7K
KRC104S KRC104S
GND GND Q8306 B
20 Q8302 B 20 5V_HDMI_4 C8324
5V_HDMI_1
R8302 HP_DET R8316 C +3.5V_ST 0.1uF
HP_DET C
19 19
5V 1K 5V 1K
18 18
GND
GND D8311
D8305 R8317 JP8306
17 R8307 17 5.5V
DDC_DATA 5.5V DDC_DATA 0
0 OPT DDC_SDA_4 ESD R8326
G
DDC_SDA_1 16
16 DDC_CLK 22K
DDC_CLK JP8304
DDC_SCL_1 15 DDC_SCL_4
15 NC R8318
ESD
NC R8308 JP8305 JP8307 GND
0 GND 0
100K
ESD
D
B
S
14
D8313
CDS3C05HDMI1
5.6V
D8314
CDS3C05HDMI1
5.6V
14 CE_REMOTE D8312
CE_REMOTE
R8349
CEC_REMOTE
Q8308
CEC_REMOTE 13 MMBD301LT1G
13
BSS83
CK- CK-
CK-_HDMI1 CK-_HDMI4
12 12
CK_GND
CK_GND
11 CEC_REMOTE HDMI_CEC
11 CK+ GND
CK+ JK830310
JK830210 CK+_HDMI1 CK+_HDMI4
D0- D0-
9 9 D0-_HDMI4
D0-_HDMI1
D0_GND D0_GND
8
EAG42463001
8
EAG59023302
D0+ D0+
7 7 D0+_HDMI4
D0+_HDMI1
D1- D1-
6 6 D1-_HDMI4
D1-_HDMI1
D1_GND D1_GND
5 5
D1+ D1+
4 4 D1+_HDMI4
D1+_HDMI1
D2- D2-
3 3 D2-_HDMI4 +3.3V_HDMI
D2-_HDMI1
D2_GND D2_GND
2 2
D2+ D2+
1 1 D2+_HDMI4
D2+_HDMI1
KJA-ET-0-0032 GND
YKF45-7058V
GND
0.1uF
C8305
0.1uF
C8307
0.1uF
C8308
0.1uF
C8309
0.1uF
C8310
UI_HW_PORT1
0.1uF
C8311
SIDE_HDMI_PORT4
HDMI4
C8319
+5V_NORMAL +5V_NORMAL
E 0.1uF
5V_HDMI_1 5V_HDMI_2
HDMI_3 C8320
D8300 KRC104S HDMI_HPD_2
D2-_HDMI4
D1-_HDMI4
D2+_HDMI4
5.5V
D1+_HDMI4
CK+_HDMI4
HDMI_CLK-
HDMI_CLK+
HDMI_RX0-
HDMI_RX0+
HDMI_RX1-
HDMI_RX1+
D0-_HDMI4
CK-_HDMI4
Q8303 B
DDC_SCL_4
DDC_SDA_4
D0+_HDMI4
HDMI_RX2-
HDMI_RX2+
HDMI_SDA
HDMI_SCL
HDMI_HPD_4
GND E 0.1uF
OPT R8309 HDMI_3 5V_HDMI_4
A2
A1
A2
A1
SHIELD HDMI_3 C 4.7K 5V_HPD2 5V_HPD2 HDMI_3 +5V_NORMAL C8321
KRC104S 5V_HPD1 D8309
D8306
20 HDMI_3 GND Q8300 B 0.1uF
5V_HDMI_2
C
C
HP_DET R8300 C R8325 C8322
1.8K C8312
19
5V 1K 0.1uF 0.1uF
33
33
33
33
33
33
R8312 R8314 R8319 R8322 16V
18
GND 47K 47K 47K 47K R8324
HDMI_3 D8303
R8303 JP8300 HDMI_3 HDMI_3 1.8K
17 5.5V
DDC_DATA 0
R8329
R8330
R8331
R8332
OPT
R8333
R8334
DDC_SDA_2 DDC_SDA_1 DDC_SDA_2
16
DDC_CLK
0
DDC_SCL_2 DDC_SCL_1 DDC_SCL_2

OPT
15
R8339
NC R8304 JP8301 GND +1.8V_HDMI

0
14 HDMI_3
CE_REMOTE
CEC_REMOTE
13
CK-
CK-_HDMI2 C8318 C8323
12 C8316
CK_GND 0.1uF 0.1uF
0.1uF
16V 16V
11 16V
CK+ +5V_NORMAL
JK830010 +5V_NORMAL
CK+_HDMI2 5V_HDMI_3 HDMI3
5V_HDMI_4
D0-
9 D0-_HDMI2
D0_GND Place close 5V_HDMI_3
A2
A1
8
EAG59023302
A2
A1
to TDA9996
OUT_D0-
OUT_D0+
VSS_12
OUT_D1-
OUT_D1+
VDDO[1V8]
OUT_D2-
OUT_D2+
VSS_11
VDDDC[1V8]_3
RXD_D2+
RXD_D2-
VDDH[3V3]_8
RXD_D1+
RXD_D1-
VSS_10
RXD_D0+
RXD_D0-
VDDH[3V3]_7
RXD_C+
RXD_C-
RXD_DDC_CLK
RXD_DDC_DAT
RXD_5V
RXD_HPD
5V_HPD3 5V_HPD4
D0+ HDMI1
7 D0+_HDMI2 D8307 D8310
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
C
C
D1-
100
6 VSS_1 1 75 VDDH[1V8]_2
D1-_HDMI2 C8317
5V_HDMI_1 OUT_C+ R12K R8344
D1_GND 2 74 0.1uF
5
OUT_C- 3 73 VSS_9 12K 16V
D1+ R8313 R8315 R8320 R8323
4 D1+_HDMI2 VDDO[3V3] 4 72 RXC_D2+
47K 47K 47K 47K D2+_HDMI3
D2- OUT_DDC_CLK 5 71 RXC_D2-
3 C8302 D2-_HDMI3
D2-_HDMI2 DDC_SDA_3 DDC_SDA_4 OUT_DDC_DAT VDDH[3V3]_6
0.1uF 6 70
D2_GND
2 16V VSS_2 7 69 RXC_D1+
DDC_SCL_4 D1+_HDMI3
D2+ DDC_SCL_3 OPT VDDDC[1V8]_1 8 68 RXC_D1-
1 D1-_HDMI3
D2+_HDMI2 R8328 RXA_HPD IC8300 VSS_8
HDMI_HPD_1 9 67
0 RXA_5V 10 66 RXC_D0+
D0+_HDMI3
RXA_DDC_DAT 11 TDA19997 65 RXC_D0-
D0-_HDMI3
DDC_SDA_1 RXA_DDC_CLK VDDH[3V3]_5
12 64
HDMI_3 DDC_SCL_1 RXA_C- 13 63 RXC_C+
YKF45-7058V CK-_HDMI1 CK+_HDMI3
EDID Pull-up RXA_C+ 14 62 RXC_C-
GND
UI_HW_PORT3 CK+_HDMI1 CK-_HDMI3
VDDH[3V3]_1 15 61 RXC_DDC_CLK
DDC_SCL_3
RXA_D0- 16 60 RXC_DDC_DAT
D0-_HDMI1 DDC_SDA_3
RXA_D0+ 17 59 RXC_5V
D0+_HDMI1 VSS_3 RXC_HPD
18 58 HDMI_HPD_3
RXA_D1- 19 57 CEC R8345
D1-_HDMI1 0 Ready for TDA19997
RXA_D1+ 20 56 VSS_7
OPT
D1+_HDMI1 VDDH[3V3]_2 VDDS[3V3]
E 21 55
+3.3V_HDMI
RXA_D2- 22 54 CDEC_STBY
D8301 KRC104S HDMI_HPD_3 D2-_HDMI1 OPT
5.5V RXA_D2+ 23 53 INT_N/MUTE R8346 0 R8347
GND Q8304 B D2+_HDMI1
OPT E R8310 VDDH[1V8]_1 RXE_DDC_DAT 4.7K
24 52 OPT
SHIELD C 4.7K 5V_HPD3
KRC104S AUX_5V 25 51 RXE_DDC_CLK OPT
GND Q8301 B 4.7K
20 5V_HDMI_3
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
R8348
HP_DET R8301 C
C8315
0.1uF
19
PD
5V 1K
+5V_NORMAL
18
VSS_4
TEST1
VSS_5
VSS_6
GND
RXB_5V
RXB_C-
RXB_C+
RXB_HPD
RXB_D0-
RXB_D0+
RXB_D1-
RXB_D1+
RXB_D2-
RXB_D2+
I2C_SDA
I2C_SCL
D8304 R8327
R8305 JP8302
CDEC_DDC
17 5.5V
DDC_DATA 0
DDC_SDA_3 OPT C8300 0
RXB_DDC_DAT
RXB_DDC_CLK
VDDH[3V3]_3
VDDH[3V3]_4
0 OPT
16
R8336 0 TEST2
VDDDC[1V8]_2
VDDDC[1V8]_4
DDC_CLK 0.1uF R8343

15 DDC_SCL_3
NC R8306
JP8303 GND
0 C8313
14
CE_REMOTE 0.1uF C8314
CEC_REMOTE 16V 0.1uF
13
CK- 16V
CK-_HDMI3
12 5V_HDMI_2
CK_GND +1.8V_HDMI
OPT
R8335
0
11
CK+
JK830110 CK+_HDMI3
D0- C8306
9 D0-_HDMI3 C8303 0.1uF
C8301 C8304
D0_GND 0.1uF 0.1uF 0.1uF 16V
22
EAG59023302
16V
R8340
16V 16V
R833822
D0+
7 D0+_HDMI3 R8337
D1- 0
6 D1-_HDMI3
D1_GND
5
D1+
4 D1+_HDMI3
DDC_SCL_2
D2-
DDC_SDA_2
CK-_HDMI2
CK+_HDMI2
D0-_HDMI2
D0+_HDMI2
D1-_HDMI2
D1+_HDMI2
D2-_HDMI2
D2+_HDMI2
3 D2-_HDMI3
HDMI_HPD_2
D2_GND
2
D2+ HDMI2
1 D2+_HDMI3
SDA2_3.3V
SCL2_3.3V
YKF45-7058V
GND
UI_HW_PORT2

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR LEE GI YOUNG
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. HDMI 8
RGB PC
IC8401-*1
R1EX24002ASAS0A
IC8400 +5V_NORMAL
74F08D A0 VCC
+5V_NORMAL
1 8
A1 WP
2 7 D8409
D0A VCC
1 14 A2 SCL
ENKMC2838-T112
3 6 A1
DEV C
D0B D3B C8401 VSS SDA
4 5
2 13 0.1uF A2
R8401
22 Q0 D3A RGB_EDID_RENESAS
RGB_HSYNC 3 12
IC8401
RGB_VSYNC D1A Q3 M24C02-RMN6T
4 11
0.1uF
16V
R8402 R8420
C8404
2.7K
R8414
2.7K
E0
R8413
22 1 8 VCC 10K
D1B D2B R8422
5 10 E1 2 WC 100
7 EDID_WP
E2 3 SCL R8416
Q1 D2A 6 RGB_DDC_SCL
6 9 22
VSS SDA R8415
4 5 RGB_DDC_SDA
0IMMR00014A
22
GND Q2
7 8
RGB_EDID_ST
18pF 50V
18pF 50V
R8417
0
R8421
R8406 0
C8405
C8406
22
OPT
D8410
CDS3C05HDMI1
5.6V
R8405 OPT
OPT OPT +3.3V_NORMAL
BCM Reference 22 D8408
50V
50V
CDS3C05HDMI1
22pF
22pF
C8403
C8402
5.6V R8424
30V
30V
10K
D8401
ADUC30S03010L_AMODIODE
D8403
ADUC30S03010L_AMODIODE
1K
L8408 60-ohm R8425
DSUB_B DSUB_DET
RGB_BEAD
L8409 60-ohm OPT
0 OPT C8409
DSUB_G D8411
R8423 100pF
RGB_BEAD 5.6V
50V
ADMC5M03200L_AMODIODE
L8410 60-ohm
DSUB_R
RGB_BEAD
BCM Reference
RED_GND
GND_2
RED
GREEN_GND
DDC_DATA
GREEN
BLUE_GND
H_SYNC
BLUE
NC
V_SYNC
GND_1
SYNC_GND
DDC_CLOCK
DDC_GND
R8403 R8404 R8407

75 75 75 D8402 D8404 D8405 RGB_0OHM
RGB IN
30V 30V 30V L8408-*1
11
12
13
14
15
0
SHILED
16
6
7
8
9
10
RGB_0OHM
L8409-*1
0
1
2
3
4
5
RGB_0OHM SPG09-DB-010
L8410-*1 JK8402
0
+3.3V_NORMAL
JK8400
JP8401 JST1223-001
GND RGB AUDIO IN
1
JP8402 JK8401
R8400
VCC PEJ027-01
2
1K
JP8400 3 E_SPRING
SPDIF_OUT
Fiber Optic
VINPUT
3
6A T_TERMINAL1
4
D8400 C8400
30V 0.1uF C8407
OPT 16V FIX_POLE 7A B_TERMINAL1
PC_R_IN
D8406 1uF R8418
4 R_SPRING 0
AMOTECH R8411 25V
5.6V 470K
5 T_SPRING
C8408
7B B_TERMINAL2
PC_L_IN
1uF R8419
T_TERMINAL2 D8407 R8412 0
6B AMOTECH 25V
470K
5.6V

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS EUROBBTV 2009.06.18
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. ETC SUB BOARD I/F 9
ALL for SIDE_GENDER option
SIDE CVBS PHONE JACK

(New Item Developmen)
SIDE_AV_CVBS
R8603
0
D8608 C8605
5.1V 47pF
JK8600 50V
KJA-PH-1-0177 D8609
5.1V
5 M5_GND
+3.3V_NORMAL
4 M4
R8605
10K
3 M3_DETECT
SIDE_AV_DET
R8608
1K
1 M1 D8601 C8600
5.6V
100pF
6 M6 50V
C8607 R8606
25V 0
SIDE_AV_L_IN
1uF
R8601 C8611
D8602
100pF
5.6V 470K
50V
C8606 R8607
25V 0
SIDE_AV_R_IN
1uF
R8602 C8612
D8603
5.6V 470K 100pF
50V
SIDE COMPONENT PHONE JACK

(New Item Developmen)
L8600
270nH
SIDE_COMP_Y
C8601 C8608
D8610
5.1V
27pF 27pF
D8611 50V 50V
5.1V
+3.3V_NORMAL
C8613 0.1uF
JK8601 SIDE_COMP_INCM
Near J
KJA-PH-1-0177 R8600
10K Run Along SIDE_COMP_Y_IN,SIDE_COMP_Pr_IN,SIDE_COMP_Pb_IN Trace
R8604
R8609
36
5 M5_GND 1K
SIDE_COMP_DET
C8604
4 M4 D8606 100pF
5.6V 50V
3 M3_DETECT
L8602
270nH
1 M1
SIDE_COMP_Pb
D8607 C8603 C8610
6 M6 5.5V 27pF 27pF
50V 50V
L8601
270nH
SIDE_COMP_Pr
D8605 C8602 C8609
5.5V 27pF 27pF
50V 50V

SIDE_GENDER
WIRELESS READY MODEL
JK8700
KJA-PH-3-0168
Wireless power VCC[24V/20V/17V]_1

1
VCC[24V/20V/17V]_2
2
VCC[24V/20V/17V]_3
3
VCC[24V/20V/17V]_4
4
VCC[24V/20V/17V]_5
+24V 5
VCC[24V/20V/17V]_6
6
+3.3V_NORMAL DETECT
7
C8700 R8704
22K C8701 INTERRUPT
0.1uF 8
2.2uF TP8700
50V GND_1
S R8714
9
10K
G RESET
TP8701 10
R8705 Q8701 R8713 1K
2.2K GND_2
AO3407A D L8700 WIRELESS_DETECT 11
I2C_SCL
R8702 C WIRELESS_SCL 12
10K MLB-201209-0120P-N2
WIRELESS_PWR_EN I2C_SDA
B WIRELESS_SDA 13
Q8700 GND_3
C8702 14
E 0.01uF C8704 C8705
50V 10uF 10uF UART_RX
WIRELESS_RX 15
35V 35V
UART_TX
WIRELESS_TX 16
GND_4
17
IR
IR_PASS 18
GND_5
19
GND_6
20
21
SHIELD
+3.5V_ST
NON_WIRELESS WIRELESS
R8703 0
R8707
0
IC8700
NON_3DTV MC14053BDR2G
R8700
WIRELESS_DL_RX
0
Y1 VDD
WIRELESS_TX 1 WIRELESS 16
C8703 RS232C & Wireless
Y0 Y BCM_TXD1 0.1uF
BCM_TX 2 15
Z1 X BCM_RXD1
3 14
R8708 0
WIRELESS_DL_TX WIRELESS_SW_CTRL SELECT PIN STATUS
Z X1 NON_3DTV
4 13
WIRELESS_RX
R8706 HIGH X1/Y1/Z1 WIRELESS Dongle connect --> WIRELESS RS232
Z0 X0
0 NON_WIRELESS +3.5V_ST
5 12 BCM_RX
LOW X0/Y0/Z0 WIRELESS Dongle Dis_con --> S7 RS232
INH A
6 11
OPT
4.7K
R8711
R8701 0 VEE B
7 10
WIRELESS
VSS C WIRELESS_SW_CTRL
8 9
47K
OPT
R8712

WIRELESS
+24V +24V_AMP
L8803
MLB-201209-0120P-N2
C8827
0.1uF
50V
+1.8V_AMP
+3.3V_NORMAL
IC8800 CCFL = 20V
AP1117E18G-13
IN ADJ/GND Edge_LED 32~47 Inch = 20V
R8800
1
3 Vd=1.4V 1 120 mA
2
C8800 OUT C8803 55 Inch & IOP Module = 24V
C8802
0.1uF 10uF 0.1uF
16V 10V 16V
+24V_AMP
SPK_L+
D8800
1N4148W R8812 R8819 L8805
EMI 100V 12 12 AD-9060 R8820
R8809 C8841
OPT 2S 2F 0.1uF 4.7K
3.3 C8835 50V
390pF
EMI 50V C8839 SPEAKER_L
C8832 0.47uF
C8826 1S 1F 50V
C8820 C8824 10uF 0.01uF
0.1uF 0.1uF 50V C8836 C8842
50V 50V 35V 390pF 0.1uF R8821
+3.3V_NORMAL D8801 50V 15uH 50V
1N4148W R8813 R8817 4.7K
100V 12 12
C8819 OPT
22000pF SPK_L-
50V C8823
22000pF
L8802 50V
C8825
1uF
BLM18PG121SN1D
25V
AMP_RESET_N
EP_PAD
PGND1A_2
PGND1A_1
OUT1A_2
OUT1A_1
PVDD1A_2
PVDD1A_1
PVDD1B_2
PVDD1B_1
OUT1B_2
OUT1B_1
PGND1B_2
PGND1B_1
BST1B
VDR1B
C8808
1000pF
56
55
54
53
52
51
50
49
48
47
46
45
44
43
50V
BST1A 1 42 NC C8828 SPK_R+
AUD_MASTER_CLK C8816 25V1uF
VDR1A 2 THERMAL 41 VDR2A C8830
1uF 25V /RESET 57 BST2A 22000pF
3 40 D8802 R8818
+1.8V_AMP 50V R8814
C8811 AD 4 39 PGND2A_2 1N4148W 12 12 L8804
+1.8V_AMP 0.1uF DGND_1 PGND2A_1 100V AD-9060 C8843 R8822
5 38 OPT 2S 2F
GND_IO 37 OUT2A_2 C8837 0.1uF 4.7K
6 IC8801 390pF C8840 50V SPEAKER_R
CLK_I 7 36 OUT2A_1 50V 0.47uF
L8801 50V
C8810 VDD_IO 8 35 PVDD2A_2 1S 1F
C8806 1000pF EAN60969601 C8838
L8800 50V DGND_PLL 9 34 PVDD2A_1 390pF
100pF 50V
R8806 AGND_PLL 33 PVDD2B_2 D8803 15uH C8844 R8823
50V 10
3.3K LF PVDD2B_1 1N4148W R8815 R8816 0.1uF 4.7K
11 NTP-7000 32
BLM18PG121SN1D
100V 12 12 50V
AVDD_PLL 12 31 OUT2B_2 OPT SPK_R-
BLM18PG121SN1D
DVDD_PLL 13 30 OUT2B_1 +24V_AMP
GND 14 29 PGND2B_2
OPT
C8801 C8804 OPT
10uF 0.1uF C8805 C8807
10V 10uF
15
16
17
18
19
20
21
22
23
24
25
26
27
28
16V 0.1uF
10V 16V
WCK
BCK
SDA
SCL
+1.8V_AMP
DVDD
C8834
SDATA
VDR2B
BST2B
C8831 C8833
DGND_2
/FAULT
10uF
0.1uF 0.1uF 35V
MONITOR0
MONITOR1
MONITOR2
PGND2B_1
50V 50V
OPT
C8815 C8822
10uF C8818 1uF
0.1uF 25V C8829
10V
16V
22000pF
50V
R8801 100
AUD_LRCH
R8802 100 R8807
AUD_LRCK 0
R8803 100 POWER_DET
AUD_SCK
R8804 100 C8821 OPT
SDA1_3.3V 1000pF
R8805 100 50V
SCL1_3.3V +3.5V_ST
C8809 C8812 C8813 C8814 C8817
33pF 33pF 47pF 47pF 47pF
50V 50V 50V 50V 50V
R8810 WAFER-ANGLE
EMI EMI EMI R8808 100 10K
C R8824
AMP_MUTE1 0
B R8811 SPK_L+
Q8800 AMP_MUTE 4
2SC3052 10K R8825
0
E SPK_L-
AMP_MUTE1 3
R8826
0
For 3 AMP MODEL SPK_R+
2
R8827
0
SPK_R-
1
P8800

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR KIM JONG HYUN
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. NTP7000 38
+1.5V_MEMC D1.5V_DDR3
D1.5V_DDR3 DDR3 1.5V By CAP - Place these Caps near Memory
L8900
C8902 C8904
10uF 0.1uF
10V 16V
C8908
10uF
C8922
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
C8913
C8914
C8915
C8916
C8917
C8918
C8919
C8920
C8921
C8923
C8924
C8925
C8926
C8927
C8928
C8929
C8930
Close to DDR Power Pin
+3.3V_MEMC
+12V +3.3V_MEMC
IC8903
AOZ1072AI
L8905
PGND LX_2 3.6uH
L8902 1 8
D1.5V_DDR3 CIC21J501NE
D1.5V_DDR3 NR8040T3R6N
VIN LX_1
2 7
1%
R8933
27K
AGND EN POWER_ON/OFF2_2
C8942 C8944
R8900
3
2A 6
1K 1%
R8919
R1 22uF 0.1uF
1K 1%
R8928
1%
C8932 C8934 10V 16V

MVREFDQ
4.7K
10uF 10uF 10K

MVREFCA
R8934
FB COMP
1%
25V 25V 4 5 OPT
1%
0.1uF
9.1K C8940
1000pF
0.1uF
2200pF
R8904
R8925 100pF
1000pF
R8920
1K
OPT C8937 50V
1K
C8903
OPT
C8901
C8910
C8909
1%
R8935
10K
R2
Vout=0.8*(1+R1/R2)
AR8900
FRC_DQL[5] DDR3_DQL[5]
10
AR8901
IC8900
FRC_A[9] DDR3_A[9]
H5TQ1G63BFR-12C
FRC_A[2] DDR3_A[2] DDR3_A[0-12]
FRC_A[0] DDR3_A[0]
M8 N3 DDR3_A[0]
FRC_BA2 DDR3_BA2 MVREFCA VREFCA A0
P7 DDR3_A[1]
10 A1 URSA3 DDR3 1.5V
P3 DDR3_A[2]
AR8902 A2
H1 N2 DDR3_A[3]
FRC_DQL[0] DDR3_DQL[0] MVREFDQ VREFDQ A3
P8 DDR3_A[4]
FRC_DQL[2] DDR3_DQL[2] A4 +3.3V_MEMC +1.5V_MEMC
P2 DDR3_A[5]
FRC_DQL[6] DDR3_DQL[6] R8921 A5
L8 R8 DDR3_A[6]
FRC_DQL[4] DDR3_DQL[4] ZQ A6
240 R2 DDR3_A[7]
10 A7 IC8901 1074 mA
1% T8 DDR3_A[8]
AR8903 A8
B2 R3 DDR3_A[9]
FRC_DQU[7] DDR3_DQU[7] VDD_1 A9 AP1117EG-13
D9 L7 DDR3_A[10]
L8903
FRC_DQU[1] DDR3_DQU[1] VDD_2 A10/AP

G7 R7 DDR3_A[11]
FRC_DQU[5] DDR3_DQU[5] VDD_3 A11
CIC21J501NE
K2 N7 DDR3_A[12]
FRC_DQU[3] DDR3_DQU[3] VDD_4 A12/BC
K8 T3
10 VDD_5 A13
N1 IN OUT
VDD_6
R8909 N9 M7
FRC_DMU DDR3_DMU VDD_7 A15
R1
10 VDD_8 ADJ/GND
R9 M2
R8936
1
R8910 DDR3_BA0
VDD_9 BA0
N8
1%
FRC_DQSL DDR3_DQSL
270
10 BA1 DDR3_BA1
M3
R8927
BA2 DDR3_BA2 C8935

R8913 A1 C8938 C8946
DDR3_MCLK 10uF
FRC_DQSLB DDR3_DQSLB VDDQ_1 10uF 0.1uF
A8 J7 16V
10 R8929 16V
VDDQ_2 CK
150
C1 K7 56
OPT
R8922
R8914 VDDQ_3 CK
FRC_DML DDR3_DML C9 K9 DDR3_MCLKB
VDDQ_4 CKE 1%
10 D2
VDDQ_5 DDR3_CKE
D1.5V_DDR3 E9 L2
R8911 VDDQ_6 CS
F1 K1
FRC_DQSU DDR3_DQSU VDDQ_7 ODT DDR3_ODT
10 H2 J3
R8912 VDDQ_8 RAS DDR3_RASB
H9 K3
FRC_DQSUB DDR3_DQSUB VDDQ_9 CAS DDR3_CASB
10 L3 D1.5V_DDR3
WE DDR3_WEB R8923
J1 10K
AR8904 NC_1
J9 T2
FRC_DQU[2] DDR3_DQU[2] NC_2 RESET
L1 DDR3_RESETB
FRC_DQU[6] DDR3_DQU[6] NC_3
L9
FRC_DQU[0] DDR3_DQU[0] NC_4
T7 F3
FRC_DQU[4] DDR3_DQU[4] NC_6 DQSL DDR3_DQSL
G3
10 DQSL DDR3_DQSLB
A9 C7
VSS_1 DQSU DDR3_DQSU
AR8906 B3 B7
VSS_2 DQSU DDR3_DQSUB
FRC_A[3] DDR3_A[3] E1
VSS_3
FRC_A[5] DDR3_A[5] G8 E7
VSS_4 DML DDR3_DML
FRC_A[7] DDR3_A[7] J2 D3 DDR3_DQL[0-7]
VSS_5 DMU DDR3_DMU
FRC_DDR3_RESETB DDR3_RESETB J8
10 VSS_6
M1 E3 DDR3_DQL[0]
VSS_7 DQL0
M9 F7 DDR3_DQL[1]
VSS_8 DQL1
P1 F2 DDR3_DQL[2]
URSA3 CORE 1.26V
AR8905 VSS_9 DQL2
P9 F8 DDR3_DQL[3]
FRC_CASB DDR3_CASB VSS_10 DQL3
T1 H3 DDR3_DQL[4]
FRC_ODT DDR3_ODT VSS_11 DQL4
T9 H8 DDR3_DQL[5]
FRC_WEB DDR3_WEB VSS_12 DQL5
G2 DDR3_DQL[6]
FRC_BA0 DDR3_BA0 DQL6
H7 DDR3_DQL[7]
10 DQL7
B1 +1.26V_MEMC
VSSQ_1 +12V
R8915 B9 D7 DDR3_DQU[0] IC8902
VSSQ_2 DQU0 AOZ1072AI
FRC_RASB DDR3_RASB D1 C3 DDR3_DQU[1]
10 VSSQ_3 DQU1
D8 C8 DDR3_DQU[2] L8904
VSSQ_4 DQU2
E2 C2 DDR3_DQU[3] PGND LX_2 3.6uH
VSSQ_5 DQU3 1 8
E8 A7 DDR3_DQU[4]
VSSQ_6 DQU4
L8901
R8916 F9 A2 DDR3_DQU[5] NR8040T3R6N

FRC_MCLK DDR3_MCLK VSSQ_7 DQU5 VIN LX_1
G1 B8 DDR3_DQU[6] 2 7
10 VSSQ_8 DQU6
1%
R8917 G9 A3 DDR3_DQU[7]
R8930
3.3K
VSSQ_9 DQU7
FRC_MCLKB DDR3_MCLKB AGND EN
10
2A POWER_ON/OFF2_1 C8941 C8943
3 6 R1 22uF 0.1uF
R8926
1%
C8931 C8933 10V 16V

3.9K
10uF 10uF 10K

R8931
DDR3_DQU[0-7] FB COMP
R8918 25V 25V 4 5 OPT
FRC_CKE DDR3_CKE 6.2K C8939
10 3300pF
R8924 100pF
C8936 50V
AR8908
FRC_A[8] DDR3_A[8]
1%
FRC_A[6] DDR3_A[6]
R8932
12K
R2
FRC_A[4] DDR3_A[4] Vout=0.8*(1+R1/R2)
FRC_BA1 DDR3_BA1
10
AR8907
FRC_A[10] DDR3_A[10]
FRC_A[1] DDR3_A[1]
10

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS COMMON 2009.09.11
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. URSA3 DDR & Power 89
C9038 C9039
22pF 22pF FRC OPTION LOW HIGH

X9000
K14 NON_MIRROR MIRROR
12MHz T10 LVDS MINI_LVDS

R9029 R10 GIP NON_GIP
Serial Flash 1M R9 SCAN_OFF SCAN_ON
LVDS_TX_0_CLK_P
LVDS_TX_0_CLK_N
LVDS_TX_0_DATA0_P
LVDS_TX_0_DATA0_N
LVDS_TX_0_DATA1_P
LVDS_TX_0_DATA1_N
LVDS_TX_0_DATA2_P
LVDS_TX_0_DATA2_N
LVDS_TX_0_DATA3_P
LVDS_TX_0_DATA3_N
LVDS_TX_0_DATA4_P
LVDS_TX_0_DATA4_N
LVDS_TX_1_CLK_P
LVDS_TX_1_CLK_N
LVDS_TX_1_DATA0_P
LVDS_TX_1_DATA0_N
LVDS_TX_1_DATA1_P
LVDS_TX_1_DATA1_N
LVDS_TX_1_DATA2_P
LVDS_TX_1_DATA2_N
LVDS_TX_1_DATA3_P
LVDS_TX_1_DATA3_N
LVDS_TX_1_DATA4_P
LVDS_TX_1_DATA4_N
U10 LD NON_LD
+3.3V_MEMC
+3.3V_MEMC
IC9000-*1 R9017 R9023
W25X40BVSSIG
R9037 0 DPM_A
+3.3V_MEMC FRC_CONF0 MINI_LVDS
100 100
CS VCC
1 8
R9018 R9024
DO[IO1] HOLD
2 7
100 100
100
WP CLK
3 6
R9042
R9019 R9025
0.1uF
GND DI[IO0]
4 5
C9028
IC9000 100 100
MX25L4005CM2I-12G SW9000
R9033
4.7K
R9035
4.7K
R9020 R9026
R9052
4.7K
R9054
4.7K
R9056
4.7K
URSA3_NON_LOCAL_DIMMING
JTP-1127WEM
URSA3_MIRROR
URSA3_FLASH_WINBOND_NEW
R9000 10 CS# VCC
1 8
FRC_CONF0
H_CONV
100 100
FRC_RESET
FRC_SPI_CZ 1 2
R9001 10 SO HOLD#
2 7 R9021 R9027
FRC_SPI_DO
R9002 10K WP# SCLK R9005 10 3 4
R9053
4.7K
R9055
4.7K
R9057
4.7K
3 6 IC9000-*2
FRC_SPI_CK
FRC_SPI_CZ
FRC_SPI_DI
FRC_SPI_DO
FRC_SPI_CK 100 100
W25X40VSSIG
R9036
4.7K
GND SI R9006 10
R9034
4.7K
4 5
0
R9022 R9028
URSA3_GIP URSA3_NON_GIP
FRC_SPI_DI CS VCC
1 8
URSA3_LVDS URSA3_MINI_LVDS
EAN61009401
100 100
DO HOLD
URSA3_FLASH_MACRONIX 2 7
WP CLK
3 6
URSA3_SCANNING_OFF URSA3_SCANNING_ON
R9030 URSA3
GND DIO
100
100
URSA3_NON_MIRROR
4 5
URSA3_LOCAL_DIMMING
EAN35097301
FRC_CONF1
R9041
URSA3_FLASH_WINBOND_OLD
R9031
R9032
820
A2
B2
A4
B4
C3
C4
B3
A3
C1
C2
B1
A1
A6
B6
A8
B8
C7
C8
B7
A7
C5
C6
B5
A5
A9
B9
K14
J13
H14
G13
F14
E13
D3
D4
E4
D5
D7
F4
R7
U8
U7
T8
T7
U14
U15
R13
T13
T14
T10
T11
R10
U11
R9
U12
U10
R11
U9
R12
T9
T12
R8
U13
P13
N14
N12
N13
M14
C13
FRC_A[0-12]
RE0P
RE0N
RE1P
RE1N
RE2P
RE2N
RE3P
RE3N
RE4P
RE4N
RO0P
RO0N
RO1P
RO1N
RO2P
RO2N
RO3P
RO3N
RO4P
RO4N
REXT
RECKP
RECKN
ROCKP
ROCKN
XTALO
XTALI
RESET
SPI_CK
SPI_CZ
SPI_DI
SPI_DO
GPIO[0]
GPIO[1]
GPIO[2]
GPIO[3]
GPIO[4]
GPIO[5]
GPIO[8]
GPIO[9]
FRC_A[0] E2 B14
GPIO[10]
GPIO[12]
GPIO[13]
GPIO[14]
LTD_DE_L
LTD_DE_R
DDR3_A0/DDR2_NC A0P/RV0+ RXB0+
LTD_CLK_L
LTD_CLK_R
LTD_DA0_L
LTD_DA0_R
LTD_DA1_L
LTD_DA1_R
OP_SYNC_L
OP_SYNC_R
+3.3V_MEMC AVDD_PLL FRC_A[1] U6 A14
M_S_PIF_CS
M_S_PIF_FC
S_M_PIF_CS
S_M_PIF_FC
PLL_LOCK_L
PLL_LOCK_R
SOFT_RST_L
SOFT_RST_R
M_S_PIF_DA1
S_M_PIF_CLK
S_M_PIF_DA0
S_M_PIF_DA1
DDR3_A1/DDR2_A6 A0M/RV0- RXB0-
+3.3V_MEMC AVDD FRC_A[2] E3 C14
M_S_PIF_CLK_1
M_S_PIF_CLK_2
DDR3_A2/DDR2_A7 A1P/RV1+ RXB1+
L9004 FRC_A[3] G2 C15
CIC21J501NE DDR3_A3/DDR2_A1 A1M/RLV1- RXB1-
L9005 FRC_A[4] R4 A15
CIC21J501NE DDR3_A4/DDR2_CASZ A2P/RV2+ RXB2+
C9004 C9009 FRC_A[5] G1 B15
10uF 0.1uF FRC_A[6] U5 B16
C9019 C9024 C9029 C9032 DDR3_A6/DDR2_A0 ACKP/R3+ RXBCK+
10uF 0.1uF 0.1uF FRC_A[7] F3 A16
10uF DDR3_A7/DDR2_A5 ACKM/RV3- RXBCK-
FRC_A[8] T5 A17
FRC_A[9] F1 B17
FRC_A[10] R6 C16
FRC_A[11] R5 C17
FRC_A[12] T6
AVDD_MEMPLL AVDD_LVDS DDR3_A12/DDR2_A8
+3.3V_MEMC +3.3V_MEMC D16
B0P/RV6+ RXA0+
G3 D17
L9000 FRC_BA0 DDR3_BA0/DDR2_BA2 B0M/RV6- RXA0-
L9006 U4 D15
CIC21J501NE CIC21J501NE FRC_BA1 DDR3_BA1/DDR2_ODT B1P/RV7+ RXA1+
E1 E15
FRC_BA2 DDR3_BA2/DDR2_A12 B1M/RV7- RXA1-
C9000 C9005 F16
C9020 C9025 C9030 C9033 C9034 C9035 B2P/RV8+ RXA2+
10uF 0.1uF 10uF 0.1uF 0.1uF 0.1uF 0.1uF U1 F17
10uF FRC_MCLK DDR3_MCLK/DDR2_MCLK B2M/RV8- RXA2-
U2 F15
FRC_MCLKB DDR3_MCLKZ/DDR2_MCLKZ BCKP/WPWM RXACK+
T4 G15
FRC_CKE DDR3_CKE/DDR2_RASZ BCKM/OPT_P RXACK-
G17
B3P/OPT_N RXA3+
H2 G16
FRC_ODT DDR3_ODT/DDR2_BA1 B3M/FLK RXA3-
J1 H16
+3.3V_MEMC VDDP FRC_RASB DDR3_RASZ/DDR2_WEZ B4P/GCLK6 RXA4+
H3 H17
FRC_CASB DDR3_CASZ/DDR2_CKE B4M/GLCK5 RXA4-
H1
L9001 FRC_WEB DDR3_WEZ/DDR2_BA0
CIC21J501NE
IC9001 H15
C0P/LV0+ RXC0+
F2 J15
FRC_DDR3_RESETB DDR3_RESET/DDR2_A3 C0M/LV0- RXC0-
C9001 C9006 C9010 C9013 C9016 C9021 C9026 J17
10uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF C1P/LV1+ RXC1+
10uF M3 LGE7378A[FRC_TCON_URSA3] J16
FRC_DQSL DDR2_DQS0/DDR3_DQS0 C1M/LV1- RXC1-
N2 K16
FRC_DQSU DDR2_DQS1/DDR3_DQS1 C2P/LV2+ RXC2+
K17
C2M/LV2- RXC2-
N1 K15
FRC_DQSLB DDR2_DQSB0/DDR3_DQSB0 CCKP/LV3+ RXCCK+
N3 L15
FRC_DQSUB DDR2_DQSB1/DDR3_DQSB1 URSA3 CCKM/LV3- RXCCK-
L17
C3P/LV4+ RXC3+
R2 L16
FRC_DML DDR2_DQ7/DDR3_DQM0 C3M/LV4- RXC3-
K3 M16
FRC_DMU DDR2_DQ11/DDR3_DQM1 C4P/LV5+ RXC4+
M17
C4M/LV5- RXC4-
AVDD_DDR FRC_DQL[0] K2
+1.5V_MEMC DDR2_DQ6/DDR3_DQ0
FRC_DQL[1] R3 M15
DDR2_DQ0/DDR3_DQ1 D0P/LV6+ RXD0+
FRC_DQL[2] K1 N15
L9002 DDR2_DQ1/DDR3_DQ2 D0M/LV6- RXD0-
CIC21J501NE FRC_DQL[3] T1 N17
DDR2_DQ2/DDR3_DQ3 D1P/LV7+ RXD1+
FRC_DQL[4] J2 N16
C9007 C9011 C9014 C9017 C9022 C9027 C9031 DDR2_DQ4/DDR3_DQ4 D1M/LV7- RXD1-
C9002 FRC_DQL[5] T3 P15
10uF 10uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF DDR2_NC/DDR3_DQ5 D2P/LV8+ RXD2+
FRC_DQL[6] J3 R15
DDR2_DQ3/DDR3_DQ6 D2M/LV8- RXD2-
FRC_DQL[7] T2 R17
DDR2_DQ5/DDR3_DQ7 DCKP/GOE RXDCK+
FRC_DQL[0-7] R16
DCKM/GSC/GCLK3 RXDCK-
FRC_DQU[0] P2 T16
DDR2_DQ8/DDR3_DQ8 D3P/GSP_R RXD3+
FRC_DQU[1] L3 T17
DDR2_DQ14/DDR3_DQ9 D3M/GSP RXD3-
FRC_DQU[2] R1 T15
DDR2_DQ13/DDR3_DQ10 D4P/SOE RXD4+
FRC_DQU[3] L1 U17
DDR2_DQ12/DDR3_DQ11 D4M/POL RXD4-
FRC_DQU[4] P1
DDR2_DQ15/DDR3_DQ12
FRC_DQU[5] L2 P16
VDDC DDR2_DQ9/DDR3_DQ13 GCLK4 GCLK4
+1.26V_MEMC FRC_DQU[6] P3 P17
DDR2_DQ10/DDR3_DQ14 GCLK2 GCLK2
FRC_DQU[7] M1
L9003 DDR2_DQM1/DDR3_DQ15
FRC_DQU[0-7] D1
CIC21J501NE I2CS_SDA URSA3_SDA
M2 D2
DDR2_DQM0/DDR3_NC I2CS_SCL URSA3_SCL
C9003 C9008 C9012 C9015 C9018 C9023
10uF 10uF 0.1uF 0.1uF 0.1uF 0.1uF P14
PWM0 FRC_PWM0
R9011 100 C9 R14
I2CM_SDA PWM1 FRC_PWM1
R9012 100 D9
I2CM_SCL
R9013 100 P7 B13
I2CM_SDA2_L LPLL_FBCLK V_SYNC
100 N8 U16 R9043 0
R9014 I2CM_SCL2_L LPLL_OUTCLK OPT
R9015 100 P9 A13
I2CM_SDA2_R LPLL_REFIN
R9016 100 N10
I2CM_SCL2_R
P9000 +3.3V_MEMC
AVDD_1
AVDD_2
AVDD_DDR_1
AVDD_DDR_2
AVDD_DDR_3
AVDD_DDR_4
AVDD_DDR_5
AVDD_DDR_6
AVDD_LVDS_1
AVDD_LVDS_2
AVDD_LVDS_3
AVDD_LVDS_4
AVDD_MEMPLL
AVDD_PLL_1
AVDD_PLL_2
DVDD_DDR[1.26V]
VDD_EVEN
VDD_ODD
VDDC_1
VDDC_2
VDDC_3
VDDC_4
VDDC_5
VDDC_6
VDDC_7
VDDC_8
VDDP_1
VDDP_2
VDDP_3
VDDP_4
VDDP_5
VSS_1
VSS_2
VSS_3
VSS_4
VSS_5
VSS_6
VSS_7
VSS_8
VSS_9
VSS_10
VSS_11
VSS_12
VSS_13
VSS_14
VSS_15
VSS_16
VSS_17
VSS_18
VSS_19
VSS_20
VSS_21
VSS_22
VSS_23
VSS_24
VSS_25
VSS_26
VSS_27
A10
A11
A12
B10
B11
B12
C11
D11
TESTPIN
VB1_TEST
12505WS-04A00
F8
F9
L5
L6
L7
L8
M7
M8
M6
J5
F6
F7
G5
G6
G7
H5
H6
J6
K5
K6
G8
G9
H7
H8
H9
J4
J7
J8
J9
K7
K8
K9
L9
M9
N4
P6
G12
H12
J12
K12
F11
F12
E16
E17
G11
M10
M11
C10
C12
G10
H10
H11
J10
J11
K10
K11
L10
L11
A10
A11
A12
B10
B11
B12
C11
D11
L13
F10
1K
1K
1K
1K
1
URSA3_SDA
22 R9003
R9040
OPT
2 AVDD AVDD_DDR AVDD_LVDS AVDD_PLL VDDC VDDP

URSA3_SCL 0
R9044
22 R9004 FRC_CONF0
R9046
R9048
R9050
SCL3_3.3V
22 R9007
3 FRC_CONF1
AVDD_MEMPLL
SDA3_3.3V FRC_PWM1
22 R9008
4 FRC_PWM0
OPT
1K
GVDD_ODD
5
GVDD_EVEN
URSA3_SCL SCL1_3.3V
22 R9009
OPT LD_SCAN
SCAN_BLK2 R9038 100
VDDC FRC_PWM1
R9047 OPT1K
URSA3_SDA SDA1_3.3V
R9049 OPT 1K
R9045
R9051 OPT 1K
22 R9010 L9007 LD_SCAN

CIC21J501NE R9039 100 FRC_PWM0
SCAN_BLK1/OPC_OUT
C9036 C9037
10uF 0.1uF
I2C ADR: GPIO1: HI:B8 LOW:B4

CHIP_CONF: {GPIO8, PWM1, PWM0}

CHIP_CONF= 3 d5: boot from internal SRAM

CHIP_CONF= 3 d6: boot from EEPROM

Separate DVDD_DDR Power CHIP_CONF= 3 d7: boot from SPI Flash

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS COMMON 2009.09.11
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. URSA3 (NO L.D.) 90
D9103
[LEVEL Shift Block] MMSD4148T1G VDD_LCM
[POWER Block] EN2 (+16V)
VCC_LCM 100V
(+3.3V) * Voltage Target CHECK Value!!
VDD_LCM = 16.25V
VGH = 28.50V R9156 R9165 C9134 C9138 To reduce
VGL = -5.35V 150K 18K OPT Audible noise
R9108 1% 1%
100 TCON_42_FHD OPT 0.1uF
50V To reduce C9153
GIP C9150 R9182
C9139 Audible noise C9142 100uF
1uF 1uF 9.1K
C9135 C9141 50V 25V
C9102 R9109 R9168-*1 R9157 R9166 OPT 1uF 50V 47uF 50V 1/8W
OPT 3K 75K 15K 25V
DISCHG 1% 1%
OPT GIP 33K
FLK
TCON_42_FHD TCON_42_FHD
NON_GIP
VDD_LCM L9102
C9128-*1 D9106 MBRA340T3G 22UH
(+16V) C9136
470pF D9104 MBRA340T3G C9148
50V 27pF 50V 2.8A
R9113 NON_GIP NON_GIP 22uF
10K 25V
GIP R9146
33K C9128 R9168 C9145-*1
NON_GIP R9169 C9145
1000pF 10K 560pF
50V 2.2 1000pF 50V
GIP
EP[VGOFF]
VSENSE
FLK1
FLK2
FLK3
RE
GND
YDCHG
GIP 50V
R9147-*1 R9147 VGH NON_GIP
D9100 0 2.7K GIP
VGH MMSD4148T1G NON_GIP (+25V)
28
27
26
25
24
23
22
GIP
A9 Y9 (+25V) EN2
AGND
CRST
PGOOD
COMP
FB1
SW0
SW1
LX1
LX1
PGND
GVDD_ODD_I 1 21 VDD_ODD VGH_M
100V R9152 0 PANEL_VCC
THERMAL (+25V) C9143
GVDD_EVEN_I A8 2 29 20 Y8 OPT D9101 NON_GIP (+12V)
40
39
38
37
36
35
34
33
32
31
VDD_EVEN 4.7uF/50V(3216) R9132 KDS226 0.1uF
R9153 0 THR 1 30 PGND 50V
A7 3 19 Y7 C9122
GSP/GVST_I VST C9116 0 C NON_GIP DRVP 2 29 EN2
IC9101 C9117 EN2 R9180
A6 4 18 Y6 MINI_LVDS 1uF 1uF A AC 0.47uF GND2 3 28 VL
GCLK6_I CLK6
GIP
MAX17119DS R9124 R9125 C9112 R9129 50V 50V 25V 360
4.7uF R9154 0 GIP SRC 4 27 DEL2
A5 GIP Y5
TH9000
GCLK5_I 5 17 CLK5 18K 18K 50V 56K 1%
GON EN1
R9150 0 GIP 5 IC9103 26
TCON_42_FHD
47k-ohm
A4 Y4 R9148 R9155 PANEL_VCC
6 DEV 16 DRN 6 MAX17113ETL+ 25 FSEL
GCLK4_I CLK4 R9171 R9194 (+12V)
510 NON_GIP 510 NON_GIP MODE MINI_LVDS VIN
A3 Y3 R9130 R9133 R9134 VDD_LCM 7 24
GSC/GCLK3_I 7 EAN60987201 15 10 10 C9125 68pF NON_GIP 360
CLK3 (+16V) DLP IN2
NCP18WB473F10RB
220K 1% 8 23 0
GIP GIP C9126 0.047uF NON_GIP DEV OPT
TCON_42_FHD FBP IN2
8
9
10
11
12
13
14
9 22
Value should VGH_FB
GPGND 10 EAN60924401 21 OUT C9147
be checked VGH_FB R9173 C9152
A2
A1
Y1
Y2
C9144 1uF C9155 C9162
1uF
11
12
13
14
15
16
17
18
19
20
50V 1K 22uF 22uF
GON1
GOFF
GON2
R9131 0.1uF 10V
50V 25V 25V
11K 1%
CTL
FBN
REF
FB2
BST
LX2
LX2
TCON_42_FHD R9133-*1 R9134-*1 R9148-*1 R9174
DRVN
AGND
DEL1
GCLK2_I 200 200 0 OPT
NON_GIP NON_GIP GIP R9158 R9167
R9155-*1 0 0
GOE/GCLK1_I
GIP NON_GIP
0
GIP VCC_LCM
CLK2
(+3.3V)
CLK1 L9101
C9101 VGH
0.22uF R9105 R9110 C9140 22UH
(+25V) 22 22
FLK
50V
REF
GIP GIP GIP 0.1uF 2.8A

C9123 VCC_LCM 50V
VGL_FB
C9104 R9111 R9114 R9115 R9116 1uF C9137 C9151

1uF 10 C9107 OPT 10 10 10V (+3.3V) C9164 D9105 C9146 C9149 C9154 R9181
1uF 0.1uF 0.47uF MBRA340T3G 150pF 22uF 0.1uF OPT
50V GIP OPT GIP GIP REF 50V 40V 50V 5.1K
GIP 50V 25V 50V 10V
VGL GIP GIP OPT
R9135 C9118 TCON_42_FHD
(-5V) 3.6K 10uF R9144 1% OPT
VGH 16V C9124 R9149 R9151
27K 1uF 0 0
(+25V) VGL 50V C9137-*1
VGL_FB 1uF
(-5V) D9102
KDS226 10V
R9145 1% NON_GIP
C C9127
150K
TCON_42_FHD A AC 1uF
50V
R9170
DPM EN2
10
[P-GAMMA Block] R9172

1K
Slave Address : 0xE8h
(AO Pin - GND)
SCL3_3.3V
GMA16
GMA15
VDD_LCM Signal Name Change VCC_LCM
(+16V)
To reduce (+3.3V)
Audible noise [HVDD Block]
1uF/50V(2012) R9112
R9143
33
R9103
C9106 10 3.3K
1/8W
1uF GIP R9159 R9175
50V R9136 0 0
RXA3- FLK RXD3- GSP/GVST_I GCLK2 GCLK2_I
10 NON_GIP GIP
MINI_LVDS
EP[GND]
SCL
GMA8
GMA7
NC_2
AVDD_2
C9129 C9156
6.8uH/1.8A C9119 15pF
VCC_LCM HVDD 15pF 15pF
20
19
18
17
16
SDA3_3.3V R9100 (6x6x2mm) 50V
(+3.3V) SDA GMA6 50V 50V
1 15 GMA13 VDD_LCM PANEL_VCC L9100 R9160
6.8uH NON_GIP 0 NON_GIP OPT
33 THERMAL (+16V) (+12V)
A0 2 21 14 GMA5 DEV RXD3+
GMA12 NON_GIP
DVDD IC9100 GMA4 GSP_R R9176
3 13 GMA7 MINI_LVDS 0
C9100 MAX9668ETP+ VCC_LCM GCLK4 GCLK4_I
AGND_AMP 4 12 GMA3 VGH GIP
0.1uF MINI_LVDS GMA6 (+3.3V) C9157
50V (+25V) 15pF
VCOM GMA2
OPT
VCOM 5 11 GMA4 50V
DEV
L9104
L9103
R9121 R9123 OPT
6
7
8
9
10
0 1M R9197
GIP NON_GIP
BLM18PG121SN1D
BLM18PG121SN1D
R9139 0 VGI_P 3.3K
GIP NON_GIP
R1 R9161 R9177
NC_1
GMA1
R9126 C9113 C9114 C9115 R9193 R9195
10uF/25V(3216) MINI_LVDS 0 0
AVDD_1
510K 22pF 22uF 10uF 2.2K 2.2K RXDCK+ RXA4- GCLK5_I
PGND_2
SW_2
SW_1
PG
VCOM_FB
TCON_42_FHD 50V 16V 16V GOE/GCLK1_I
GIP
AVDD_AMP
C9108 C9109 VGL C9158
VDD_LCM 10uF 10uF (-5V) C9130 15pF
16
15
14
13
VCOM_FB0 GMA3 (+16V) 25V 25V
PGND_1 GND_2 15pF 50V
1 12 OPT
1K
1K
DEV 50V
MINI_LVDS VIN_1 2 11 GND_1 NON_GIP
OPT
IC9102 R9140 0 VGI_N
VIN_2 3 TPS62110RSAR 10 FB GIP
C9103 C9105 R9162 R9178
TCON_42_FHD
MINI_LVDS
R9101
R9104
0.1uF 0.1uF R9117 EN AGND R2 0 0
4 9 RXDCK- GSC/GCLK3_I RXA4+ GCLK6_I
EAN60985901
1%
50V 50V VGL
47K C9131 C9159
(-5V) GIP
5
6
7
8
C9110 R9127 R9128
OPT R9118 150K 200K R9141 15pF 15pF
10K 1uF TCON_42_FHD 50V 50V
TCON_42_FHD
OPT 25V 0 NON_GIP OPT
LBO
LBI
SYNC
VINA
R9142
DISCHG VGL_I
0
R9196 24K Vo = 1.153*(1+R1/R2) R9163
OPT
VCOMRFB
VCOMLFB
EN2 R9122 0 R9179
10 GVDD_ODD GVDD_ODD_I DPM_A DPM
For P-Gamma Data Download GIP 0
P9100 D9107 100V
C9111 C9132 C9160
1uF 15pF 15pF
12505WS-03A00 MMSD4148T1G 50V
50V 50V
PANEL_VCC OPT
R9137
RXD4- POL
1 SCL3_3.3V 0
R9164
VCOM_FB0
R9119 C9120 0
20K 15pF GVDD_EVEN GVDD_EVEN_I
2 SDA3_3.3V 50V GIP
TCON_42_FHD C9133
1% 15pF
R9120
R9102 3 7.5K 50V
OPT
1K R9138
4 RXD4+ SOE
0
R9106
VCOMR C9121
0 15pF
R9107 50V
VCOM VCOML
0

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS COMMON 09/09/10
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. T-Con (NO L.D.) 91
32_FHD 37_FHD 42_FHD
VGH VGL VGH VGL VGH VGL
R9129-*1 R9130-*1 R9144-*1 R9129-*2 R9130-*2 R9144-*2

22K 220K 51K 47K 220K 20K 91 or 95 91 or 95
1% 1% 1% 1% 1% 1%
TCON_32_FHD TCON_32_FHD TCON_32_FHD TCON_37_FHD TCON_37_FHD TCON_37_FHD Sheet
R9131-*1 R9145-*1 R9131-*2 R9145-*2
Sheet
270K 12K 150K
11K 1%
1% 1% 1%
TCON_32_FHD TCON_37_FHD TCON_37_FHD
TCON_32_FHD
VDD VDD VDD HVDD

HVDD HVDD
R9156-*1 R9165 OPEN R9126-*1
150K 510K R9156-*2 R9165-*2 R9126-*2
1% 1% 910K 470K 470K
1% 1% 1% 91 or 95
TCON_32_FHD TCON_32_FHD TCON_37_FHD 91 or 95
R9128 OPEN Sheet
R9157-*1 R9166-*1 R9127-*1 R9128-*1 R9157-*2 R9166-*2 R9127-*2 Sheet
27K 24K 150K 200K 56K 56K 91K
1% 1% 1% 1% 1% 1% 1%
TCON_32_FHD TCON_32_FHD TCON_32_FHD TCON_32_FHD TCON_37_FHD TCON_37_FHD TCON_37_FHD
VCOM FEED BACK VCOM FEED BACK VCOM FEED BACK
R9101-*1 R9104-*1 R9101-*2 R9104-*2

1K 1K 1K 1K
1% 1% 1% 1%
TCON_32_FHD TCON_32_FHD TCON_37_FHD TCON_37_FHD
91 or 95
R9102-*1 R9102-*2 Sheet
1K 1.5K
1% 5%
47_FHD 55_FHD
VGH VGL VGH VGL
R9129-*3 R9130-*3 R9144-*3 R9129-*4 R9130-*4 R9144-*4

51K 220K 51K 510K 68K 27K
1% 1% 1% 1% 1% 1%
TCON_47_FHD TCON_47_FHD TCON_47_FHD TCON_55_FHD TCON_55_FHD TCON_55_FHD
R9131-*3 R9145-*3 R9131-*4 R9145-*4

11K 270K 150K
1% 27K 1%
1% 1%
TCON_47_FHD TCON_47_FHD TCON_55_FHD
TCON_55_FHD
VDD HVDD VDD HVDD

R9156-*3 R9165 OPEN R9126-*3 R9165 OPEN
180K 510K R9156-*4 R9126-*4
1% 1% 150K 180K
TCON_47_FHD TCON_47_FHD 1% 1%
R9157-*3 R9166-*3 R9127-*3 R9128-*3 R9127-*4 R9128-*4

75K 20K 150K 220K R9157-*4 R9166-*4 68K 56K
1% 1% 1% 75K 15K
1% 1% 1% 1% 1%
TCON_47_FHD TCON_47_FHD TCON_47_FHD TCON_47_FHD TCON_55_FHD TCON_55_FHD
VCOM FEED BACK VCOM FEED BACK
R9101-*3 R9104-*3
1K R9101 OPEN R9104 OPEN
1K
1% 1%
R9102-*3 R9102-*4
1K 0
1% 5%

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS Common 09/12/15
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. T-Con Power Option 98
BCM High Block Diagram (Input/Interface)

MAX3232CDR CVBS,L,R
IC8200
AV1
YPbPr,L,R
COMP1
YPbPr,L,R
COMP2
WIRELESS EPHY_TDP/RDP
JK8700 MC14053BDR2G
IC8700

EPHY_RDP/RDN

DSUB_R/G/B, H/V_Sync

M24C02(EEPROM)
RGB_DDC_SCL/SDA IC8401

ijtZ\\]

pjXWW
CONTROL M_REMOTE_RX
IR & KEY MOTION REMOCON
MICOM M_REMOTE_TX
P8200 P1700
UPD78F0513AGA
-GAM-AX
IC8101
BT_DM, BT_DP
BLUETOOTH
MICOM EEPROM BT_RESET
P1895
M24C16-WMN6T
16Kbit VREG_CTRL
IC8100
HDMI0_ SCL/SDA, TMDS[0-2,CLK]
HDMI 1 USB_DM1/2
HDMI1_ SCL/SDA, TMDS[0-2,CLK] TDA19997 SIDE_USB USB_DP1/2
HDMI 2 pGk USB2512
4x1 _DP/DM IC2201 wYYWXVY
HDMI2_ SCL/SDA, TMDS[0-2,CLK] HDMI Switch k}iT{
HDMI 3 IC8300
HDMI3_ SCL/SDA, TMDS[0-2,CLK]
HDMI 4
Brazil(ISDB)
AUS/TW(DVB-T) TU_CVBS/TU_SIF
FE_TS_SERIAL/SYNC/VAL_ERR/DATA_CLK
{|uly
ATV/DTV
ouptVmupt
O{|Y^WXP IF_AGC
TUNER
ISDB DEMOD
Cable (HNIM) MN884433
IF_N / P IC2800
TU2600
Brazil OPT
jGGYWXWGsnGlUGpUGhGGU
vGGGGG snlGpG|Gv
BCM High Block Diagram (Output/Audio)
DPM_A => EN2
DDR3 SDRAM
Serial Flash
H5TQ1G63BFR-12C VDD_LCM
W25X40VSSIG
(1GBit) VCC_LCM
IC9000 MINI_LVDS_POWER
IC8900
MAX17113
IC603
FRC_SPI
LEVEL SHIFT
MAX17119ETI+
DDR3 Address[0:12]
IC602
DDR3 Data[0:15]
LVDS_TX_E/O[0-4] LLV[0-5], LCLK
tz{^Z^_w
LVDS_E/O_CLK SOE/POL/GSP/H_CONV/OPT_N,
O|yzhZP RLV[0-5], RCLK
pj`WWX
DDR0 Data[0:15] DDR2 SDRAM

MT47H128M8HQ
DDR0 Address[0:13] P-GAMMA
(1GBit)
for MINI-LVDS
IC400/401
MAX9668ETP
IC601 GMA[8 bit]
DDR1 Address[0:13] DDR2 SDRAM
ijtZ\\] MT47H128M8HQ
DDR1 Data[0:15]
(1GBit)
pjXWW IC402/403 MINI_LVDS_POWER
TPS62110
NAND Flash NAND_DATA[0:7] IC600 HVDD
(4Gbit) DDR0 Data[0:15] DDR2 SDRAM
NAND04G_B2DN MT47H128M8HQ
IC101 DDR0 Address[0:13] (1GBit)
IC400/401

DDR1 Data[0:15] MT47H128M8HQ
(1GBit)
SCL2/SDA2 IC402/403
NVM
M24M01-HRMN6TP
1Mbit IC102
AMP_SCL/SDA Digital AMP
(NTP7000) PWM LPF
I2S IC8801
AUDIO
SPDIF_OUT OUT
qr_[WWGh|kpvGv|{Gzwkpm
HP_L/R_+/- AMP HP_L/ROUT
KA4558D qrXXWXGh|kpvGv|{Glhywovul
IC1100
vGGGGG snlGpG|Gv
BCM High Block Diagram (Memory)
DDR3 SDRAM
Serial Flash
H5TQ1G63BFR-12C
W25L4005CM2I
(1GBit)
IC9000
IC8900
MICOM
FRC_SPI
UPD78F0513AGA

-GAM-AX
IC8101
DDR3 Address[0:12]
DDR3 Data[0:15]
LVDS_TX_E/O[0-4] LLV[0-5], LCLK
SCL1/SDA1 snl^Z^_h
LVDS_E/O_CLK SOE/POL/GSP/H_CONV/OPT_N,
O|yzhZP RLV[0-5], RCLK
SCL1/SDA1
pj`WWX
NEC_EEPROM_SCL/SDA
DDR0 Data[0:15] DDR2 SDRAM

MICOM EEPROM MT47H128M8HQ
M24C16-WMN6T DDR0 Address[0:13] (1GBit)
16Kbit IC400/401
IC8100
ijtZ\\] MT47H128M8HQ
DDR1 Data[0:15]
(1GBit)
pjXWW IC402/403
NAND Flash NAND_DATA[0:7]
(4Gbit) DDR0 Data[0:15] DDR2 SDRAM
NAND04G_B2DN MT47H128M8HQ
IC101 DDR0 Address[0:13] (1GBit)
IC400/401

DDR1 Data[0:15] MT47H128M8HQ
(1GBit)
SCL3/SDA3 IC402/403
NVM
M24M01-HRMN6TP
1Mbit IC102
vGGGGG snlGpG|Gv
pYjGtk}Y
joW
joW
{
{
oupt
oupt
O{|Y^WXP
O{|Y^WXP
joX
joX
tpjvt
tpjvt hGhU
hGhU myjO|yzhZP
myjO|yzhZP pzkikltvk
ulj
ulj u{w^WWW
u{w^WWW tz{^Z^_
tz{^Z^_ tu__[[ZZ
OpjXWWYP
OpjXWWYP Opj\WXP
Opj\WXP OpjXZWWP
OpjXZWWP OpjZ^WXPGW_
OiGvP
joY
joY
oktpGz~
oktpGz~ |ziY
{kh```]os
{kh```]os |ziY\XY
Opj_WWPGWW
Opj_WWPGWW OpjYYWXP
joZ
joZ
u}yht
u}yht wTn
wTn
tY[tWX
tY[tWX th`]]_l{w
th`]]_l{w
OpjXWYP
OpjXWYP Opj]WXPGW_
Opj]WXPGW_
vGGGGG snlGpG|Gv
pYjGtk}X
joW
joW
{
{
oupt
oupt
O{|Y^WXP
O{|Y^WXP
joX
joX
wTn
wTn oktpGz~
oktpGz~ pzkikltvk
th`]]_l{w
th`]]_l{w {kh```]os
{kh```]os tu__[[ZZ
Opj]WXPGW_
Opj]WXPGW_ Opj_WWPGWW
Opj_WWPGWW OpjZ^WXPGW_
joY
joY
tpjvt
tpjvt hGhU
hGhU |ziY
ulj
ulj u{w^WWW
u{w^WWW |ziY\XY
OpjXWWYP
OpjXWWYP Opj\WXP
Opj\WXP OpjYYWXP
joZ
joZ
u}yht
u}yht myjO|yzhZP
myjO|yzhZP
tY[tWX
tY[tWX tz{^Z^_
tz{^Z^_
OpjXWYP
OpjXWYP OpjXZWWP
OpjXZWWP
vGGGGG snlGpG|Gv

LG Led 32le5500 PDF

Uploaded by

Copyright:

Available Formats

LG Led 32le5500 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LG Led 32le5500 PDF

Uploaded by

Copyright:

Available Formats

Internal Use Only

North/Latin America http://aic.lgservice.com

MODEL : 32LE5500 32LE5500-SA

P/NO : MFL63261812 (1004-REV00) Printed in Korea

PRODUCT SAFETY ................................................................................. 3

ADJUSTMENT INSTRUCTION .............................................................. 12

EXPLODED VIEW .................................................................................. 20

SVC. SHEET ...............................................................................................

IMPORTANT SAFETY NOTICE

General Guidance Leakage Current Hot Check (See below Figure)

Before returning the receiver to the customer, AC Volt-meter

always perform an AC leakage current check on the exposed

2. Requirement for Test

2. Luminance uniformity 77 % Full white

4. Color coordinate uniformity N/A

8. RGB Input (PC)

RGB PC Monitor Range Limits

HDMI Monitor Range Limits

* In this status you can maintain Heat-Run useless any

3.2. Set Assembly Adjustment

A Necessary items before Adjustment items

A Summary : Adjustment component 480i/1080i and RGB A Summary

=> Caution : - Never connect HDMI & D-sub Cable when

<Pic.4 Adjustment pattern : 480i / 1080p 60Hz Pattern >

A You must make it sure its resolution and pattern cause

A Adjustment method 480i Comp1, Adjust 1080p Comp1/RGB

Preparing and setting.

- HDMI-4 EDID table (0x04, 0x2A)

EDID data for LJ03B/D/E/R Chassis (Model name = LG TV)

- HDMI-1 EDID table (0x04, 0x5A)

- Analog (RGB) EDID table (0x1D)

- HDMI-2 EDID table (0x04, 0x4A)

See Working Guide if you want more information about EDID

Using HDMI input

A RS-232C Command (Commonly apply)

<Pic.5 Connection Diagram for Adjustment White balance>

- White Balance adjustment coordination and color

If it needs, then adjustment Offset.

A White Balance Adjustment (Manual adjustment)

Attachment: White Balance adjustment coordination and

Using CS-1000 Equipment.

5.5 HDCP (High-Bandwidth Digital

5.6 Test of RS-232C control.

5.7 Selection of Country option.

* Caution : Dont push The INSTOP KEY after completing

9.1 Put the USB Stick to the USB socket

9.2 Press Menu key, and move OPTION

8.2 White balance. Value.

9.4 Select download file (epk file)

9.5 After download is finished, remove the

9.6 Press IN-START key of ADJ remote

300 800 400

IC100 IR_INT : GPIO_23

GPIO_57 HP_DET LG5111_RESET

Boot Strap * NAND FLASH MEMORY 4Gbit (512M for BB)

11 38 C136 10uF L25

2.7K C114 12 37 MODEL_OPT_5 K27 GIP NON-GIP

LNA2_CTL/BOSTER_CTL R1019 100

NAND_IO[4] : CPU Endian (0) NC_13 NC_18