Product data sheet ATV312HU40N4

Characteristics variable speed drive ATV312 - 4kW - 9.2kVA -

150 W - 380..500 V - 3-phase supply
Product availability : Stock - Normally stocked in distribution facility

Price* : 688.00 USD

Disclaimer: This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications
Main
Range of product Altivar 312
Product or component type Variable speed drive
Product destination Asynchronous motors
Product specific application Simple machine
Assembly style With heat sink
Component name ATV312
Motor power kW 4 kW
Motor power hp 5 hp
[Us] rated supply voltage 380...500 V (- 15...10 %)
Supply frequency 50...60 Hz (- 5...5 %)
Phase 3 phases
Line current 13.9 Afor 380 V, 5 kA
10.6 Afor 500 V
EMC filter Integrated
Apparent power 9.2 kVA
Maximum transient current 14.3 Afor 60 s
Power dissipation in W 150 W at nominal load
Speed range 1...50
Asynchronous motor control profile Factory set : constant torque
Sensorless flux vector control with PWM type motor control signal
Electrical connection L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 0.01 in (5 mm) AWG 10
Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 0 in (2.5 mm) AWG 14
Supply Internal supply for logic inputsat 19...30 V, <= 100 mAfor overload and short-circuit protection
Internal supply for reference potentiometer (2.2 to 10 kOhm)at 10...10.8 V, <= 10 mAfor overload and
short-circuit protection
Communication port protocol CANopen
Modbus
IP degree of protection IP20 on upper part without cover plate

Apr 18, 2017

1
 IP21 on connection terminals
IP31 on upper part
IP41 on upper part
Option card CANopen daisy chain communication card
DeviceNet communication card
Fipio communication card
Modbus TCP communication card
Profibus DP communication card

Complementary
Supply voltage limits 323...550 V
Network frequency 47.5...63 Hz
Prospective line Isc 5 kA
Continuous output current 9.5 Aat 4 kHz
Output frequency 0...500 kHz
Nominal switching frequency 4 kHz
Switching frequency 2...16 kHz adjustable
Transient overtorque 170...200 % of nominal motor torque
Braking torque 100 % with braking resistor continuously
150 % without braking resistor
150 % with braking resistor for 60 s
Regulation loop Frequency PI regulator
Motor slip compensation Adjustable
Automatic whatever the load
Suppressable
Output voltage <= power supply voltage
Tightening torque 10.62 lbf.in (1.2 N.m) L1, L2, L3, U, V, W, PA, PB, PA/+, PC/-
5.31 lbf.in (0.6 N.m) Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6
Insulation Electrical between power and control
Analogue input number 3
Analogue input type AI1 configurable voltage 0...10 V, input voltage 30 V max, impedance 30000 Ohm
AI2 configurable voltage +/- 10 V, input voltage 30 V max, impedance 30000 Ohm
AI3 configurable current 0...20 mA, impedance 250 Ohm
Sampling duration AI1, AI2, AI3 8 ms analog
LI1...LI6 4 ms discrete
Response time AOV, AOC 8 ms analog
R1A, R1B, R1C, R2A, R2B 8 ms discrete
Linearity error +/- 0.2 % output
Analogue output number 1
Analogue output type AOC configurable current 0...20 mA, impedance 800 Ohm, resolution 8 bits
AOV configurable voltage 0...10 V, impedance 470 Ohm, resolution 8 bits
Discrete input logic (LI1...LI4) logic input not wired, < 13 V (state 1)
(LI1...LI6) negative logic (source), > 19 V (state 0)
(LI1...LI6) positive logic (source), < 5 V (state 0), > 11 V (state 1)
Discrete output number 2
Discrete output type (R1A, R1B, R1C) configurable relay logic 1 NO + 1 NC, electrical durability 100000 cycles
(R2A, R2B) configurable relay logic NC, electrical durability 100000 cycles
Minimum switching current R1-R2 10 mAat 5 V DC
Maximum switching current R1-R2 on inductive load, 2 A at 250 V AC, (cos phi = 0.4, and L/R = 7 ms)
R1-R2 on inductive load, 2 A at 30 V DC, (cos phi = 0.4, and L/R = 7 ms)
R1-R2 on resistive load, 5 A at 250 V AC, (cos phi = 1, and L/R = 0 ms)
R1-R2 on resistive load, 5 A at 30 V DC, (cos phi = 1, and L/R = 0 ms)
Discrete input number 6
Discrete input type (LI1...LI6) programmable, 24 V 0...100 mA with PLC, impedance 3500 Ohm
Acceleration and deceleration ramps Linear adjustable separately from 0.1 to 999.9 s
S, U or customized
Braking to standstill By DC injection
Protection type Input phase breaks drive
Line supply overvoltage and undervoltage safety circuits drive
Line supply phase loss safety function, for three phases supply drive
Motor phase breaks drive

2
 Overcurrent between output phases and earth (on power up only) drive
Overheating protection drive
Short-circuit between motor phases drive
Thermal protection motor
Insulation resistance >= 500 mOhmat 500 V DC for 1 minute
Local signalling 1 LED red drive voltage
Four 7-segment display units CANopen bus status
Time constant 5 ms for reference change
Frequency resolution Analog input 0.1...100 Hz
Display unit 0.1 Hz
Type of connector 1 RJ45 Modbus/CANopen
Physical interface RS485 multidrop serial link
Transmission frame RTU
Transmission rate 10, 20, 50, 125, 250, 500 kbps or 1 Mbps CANopen
4800, 9600 or 19200 bps Modbus
Number of addresses 1...247 Modbus
1...127 CANopen
Number of drive 127 CANopen
31 Modbus
Marking CE
Operating position Vertical +/- 10 degree
Outer dimension 184 x 140 x 150 mm
215 x 185 x 158 mm
402 x 239 x 192 mm
Height 7.24 in (184 mm)
Width 5.59 in (142 mm)
Depth 5.98 in (152 mm)
Product weight 6.83 lb(US) (3.1 kg)

Environment
Dielectric strength 2410 V DC between earth and power terminals
3400 V AC between control and power terminals
Electromagnetic compatibility Electrical fast transient/burst immunity test conforming to IEC 61000-4-4 level 4
Electrostatic discharge immunity test conforming to IEC 61000-4-2 level 3
Radiated radio-frequency electromagnetic field immunity test conforming to IEC 61000-4-3 level 3
1.2/50 s - 8/20 s surge immunity test conforming to IEC 61000-4-5 level 3
Standards IEC 61800-3
IEC 61800-5-1
Product certifications CSA
C-Tick
DNV
GOST
NOM
UL
Pollution degree 2
Protective treatment TC
Vibration resistance 1.5 mm (f = 3...13 Hz) conforming to EN/IEC 60068-2-6
1 gn (f = 13...150 Hz) conforming to EN/IEC 60068-2-6
Shock resistance 15 gn 11 ms conforming to EN/IEC 60068-2-27
Relative humidity 5...95 % without condensation conforming to IEC 60068-2-3
5...95 % without dripping water conforming to IEC 60068-2-3
Ambient air temperature for storage -13...158 F (-25...70 C)
Ambient air temperature for operation 14...122 F (-10...50 C) without derating with protective cover on top of the drive
14...140 F (-10...60 C) with derating factor without protective cover on top of the drive
Operating altitude <= 3280.84 ft (1000 m) without derating
3280.84...9842.52 ft (1000...3000 m) with current derating 1 % per 100 m

Ordering and shipping details

Category 22152 - ATV312 / ATV32 (.25 - 7.5 HP)

3
Discount Schedule CP4B
GTIN 00785901822998
Nbr. of units in pkg. 1
Package weight(Lbs) 6.9800000000000004
Returnability Y
Country of origin ID

Offer Sustainability
Sustainable offer status Green Premium product
RoHS (date code: YYWW) Compliant - since 0913 - Schneider Electric declaration of conformity
Schneider Electric declaration of conformity
REACh Reference contains SVHC above the threshold - Go to CaP for more details
Go to CaP for more details
Product environmental profile Available
Product Environmental Profile
Product end of life instructions Available
End of life manual

Contractual warranty
Warranty period 18 months