TV-Free
Video-in-motion Interface
TF-NTG2
For Mercedes Benz
Comand APS NTG2, NTG2.5, NTG4-204,
NTG4-212 and Comand Online NTG4.5
navigation systems
Legal Information
By law, watching moving pictures while driving is prohibited, the driver must not be
distracted. We do not accept any liability for material damage or personal injury resulting,
directly or indirectly, from installation or operation of this product. This product should only
be used while standing or to display fixed menus or rear-view-camera video when the
vehicle is moving, for example the MP3 menu for DVD upgrades.
Changes/updates of the vehicles software can cause malfunctions of the interface. We
offer free software-updates for our interfaces for one year after purchase. To receive a free
update, the interface must be sent in at own cost. Labor cost for and other expenses
involved with the software-updates will not be refunded.
Version 30.01.2013 TF-NTG2
Contents
1. Prior to installation
1.1. Delivery contents
1.2. Check compatibility of vehicle and accessories
1.3. Setting the Dip-switches of the CAN-Box TV-500
1.3.1.1. Exception: Vehicles with Comand Online NTG4.5
1.4. Pin-assignments
2. Installation
3. Activation of the video-in-motion function
4. Specifications
5. Technical support
1. Prior to installation
Read the manual prior to installation. Technical knowledge is necessary for installation. The
place of installation must be free of moisture and away from heat sources.
1.1. Delivery contents
Take down the SW-version and HW-version of the interface-boxes, and store this
manual for support purposes!
CAN-box TV-500 Harness
HW_____ SW_____ TV-NTG2
1
Page
Version 30.01.2013 TF-NTG2
1.2. Check compatibility of vehicle and accessories
Requirements
brand compatible vehicles navigation system
A-Class (W169) from 09/2004 til 06/2008, B-
Class (W245) from 09/2004 til 06/2008, C-Class
(W203) from 04/2004 til 02/2007, CLC-Class
(CL203) from 06/2008 til 09/2008, CLK-Class
Comand APS NTG2
(C209 W209) from 06/2004, G-Modell (G463)
from 04/2007 til 08/2008, GL-Class (X164) til
06/2008, ML-Class (W164) til 06/2008, R-Class
(W251) til 06/2008, Sprinter, Viano
A-Class (W169) from 07/2008, B-Class (W245)
from 07/2008 til 10/2011, CLS-Coupe (W219)
from 04/2008 til 12/2010, E-Class (W211) from
06/2008 til 03/2009, G-Modell (G463) from
09/2008, GL-Class (X164) from 07/2008, ML- Comand APS NTG2.5
Class (W164) from 07/2008 til 10/2011, R-Class
(W251) from 07/2008, SL-Class (R230) from
Mercedes Benz
04/2008, SLK-Class (R171) from 04/2008 til
02/2011, Viano
C-Class (W204) from 03/2007 til 02/2011, CLC-
Class (CL203) from 09/2008, GLK-Class (X204) Comand APS NTG4-204
from 09/2008, SLS (C197) from 03/2010
E-Class (W212) from 04/2009 til 05/2011, E-
Class Coupe (W207) from 05/2009 til 05/2011, Comand APS NTG4-212
CLS-Coupe (C218) from 01/2011 til 05/2011
B-Class (W246) from 11/2011, C-Class (W204)
from 03/2011, C-Class Coupe (C204) from
06/2011, E-Class (W212) from 06/2011, E-Class
Coupe (C207) from 06/2011, CLS-Coupe (C218) Comand Online NTG4.5
from 06/2011, GLK-Class (W204) from 01/2011,
ML-Class (W166) from 11/2011, SLK-Class
(R172) from 03/2011, SL-Class (R231) from 2012
VW Crafter Comand APS NTG2
Limitations
Comand APS NTG2.5 While the video-in-motion function is active, the navigation will
not work!
Comand Online NTG4.5 On some vehicles the navigation will not work while the video-
in-motion function is active. This can only be detected by a test
drive with built-in TV-free!
2
Page
Version 30.01.2013 TF-NTG2
1.3. Setting the Dip-switches of the Can-Box TV-500
Vehicle/ navigation Dip 1 Dip 2 Dip 3 Dip 4 Dip 5 Dip 6
Vehicles with NTG2/NTG4-xxx* ON OFF OFF OFF OFF OFF
Vehicles with NTG2.5 OFF OFF OFF OFF OFF OFF
* With dip1 to OFF on vehicles with NTG2/NTG4-xxx the included green cable is used to
activate the video-in-motion function.
Note: Dip switch functions of the TV-500
Dip 1 activation TV-free
Dip 2 no function
Dip 3 no function
Dip 4 no function
Dip 5 CAN-bus termination resistor on the vehicle side
Dip 6 CAN-bus termination resistor on the head-unit side
1.3.1. Exception: Vehicles with Comand Online NTG4.5
On some vehicles with Comand Online NTG4.5 the navigation performance is affected as
long as the video-in-motion function is activated. This can only be detected by a test drive
with built-in TV-free with Dip 1 to ON!
If the navigation performance is affected you have to set Dip 1 to OFF. As long as the video-
in-motion function is activated, the navigation will NOT be working! You can activate and
deactivate the video-in-motion function by pressing a button (see chaper Activation of the
video-in-motion function).
Vehicle/ navigation Dip 1 Dip 2 Dip 3 Dip 4 Dip 5 Dip 6
NTG4.5 with TV-free pemanent ON OFF OFF OFF OFF OFF
NTG4.5 with TV-free selective
OFF OFF OFF OFF OFF OFF
(hang-up button)
Note: It is possible to install the TV-free on vehicles with Comand Online NTG4.5 with
selective activation generally.
3
Page
Version 30.01.2013 TF-NTG2
1.4. Pin-assignments
Pin-assignment vehicle connector
Cable colour Assignment
Red/Blue +12Volt Permanent 15
Brown Ground Pin 12
Brown/Red CAN HIGH Pin 11
Brown CAN LOW Pin 9
Pin-assignment of the CAN-Box TV-500 (Molex 8pin)
Cable colour Pin-No. Assignment
Yellow Pin 4 CAN-HIGH connection to the head-unit
Blue Pin 3 CAN-LOW connection to the head-unit
Yellow/Black Pin 8 CAN-HIGH connection to the vehicle
Blue/Black Pin 7 CAN-LOW connection to the vehicle
Red Pin 1 +12V permanent
Black Pin 5 Ground
Green Pin 6 Activation of the video-in-motion function
(+12V = TV-free activated)
White Pin 2 Trigger output (+12V DC 500mA)
4
Page
Version 30.01.2013 TF-NTG2
2. Installation
Switch off ignition and disconnect the vehicles battery! If according to factory rules
disconnecting the battery has to be avoided, it is usually sufficient to put the vehicle is
sleep-mode. In case the sleep-mode does not show success, disconnect the battery with a
resistor lead.
Instruction for vehicles with NTG2:
1. Remove all covers of the navigation computer.
2. Remove the 4 screws of the navigation computer and pull it
out.
3. RemoveQuadlock connector from the navigation computer NTG2
and connect it to Harness TV-NTG2.
4. Remove the both 12pin inserts from the original Quadlock
connector and connect them together with the optical leads
to the Harness TV-NTG2. Connect the TV-NTG2 to the
navigation computer.
Instruction for vehicles with NTG2.5:
1. Remove the navigation computer from the centre console.
2. RemoveQuadlock connector from the navigation computer
and connect it to Harness TV-NTG2.
NTG2.5
3. Remove the both 12pin inserts from the original Quadlock
connector and connect them together with the optical leads
to the Harness TV-NTG2. Connect the TV-NTG2 to the
navigation computer.
5
Page
Version 30.01.2013 TF-NTG2
Instructions for vehicles with NTG4-2xx (NTG4.5 similar):
1. Remove the centre air nozzle unit with the accordant
tool kit.
2. Remove both TORX-screws.
3. Slide upward the interlock behind the removed TORX
screws and pull out the navigation computer.
(In the right picture the interlock is closed!)
.In this picture the interlock is open.
4. Remove Quadlock connector from the navigation computer
and connect it to Harness TV-NTG2.
5. Remove the both 12pin inserts from the original Quadlock
connector and connect them together with the optical leads
to the Harness TV-NTG2. Connect the TV-NTG2 to the
navigation computer.
6. Remove twin Fakra connector (GPS, Bluetooth) from the
navigation computer and connect it to the female Fakra
connector of harness TV-NTG2. Connect the twin Fakra
connector of harness TV-NTG2 to the navigation computer.
6
Page
Version 30.01.2013 TF-NTG2
3. Activation of the video-in-motion function
On vehicles with Comand APS NTG2/NTG4-2xx and on some vehicles with Comand Online
NTG4.5 the video-in-motion function is activated permanently without disturbing the
navigation performance.
On vehicles with Comand APS NTG2/NTG4-2xx the video-in-motion can be activated and
deactivated by Dip 1 or alternatively by the included loose green cable in connection with a
switch (not included in delivery).
Video-in-motion permanent
With dip1 to ON the video-in-motion function is activated permanently without disturbing
the navigation performance.
Video-in-motion selective
With dip1 to OFF the included green cable is used to activate the video-in-motion function.
Connect a switch to the green cable and connect the green cable to +12V ACC.
+12V = TV-Free is activated
0V = TV-Free is not activated
Note: The loose white cable is not required and must be isolated.
On vehicles with Comand APS NTG2.5 and on some vehicles with
Comand Online NTG4.5 select the navigation level on the instrument
and press the hang-up-button on the steering-wheel for more than 3
seconds to activate/deactivate the video-in-motion function. When the
ignition is off, the video-in-motion interface will be automatically
disabled.
Note: As long as the video-in-motion function is activated, the navigation of the command
will NOT be working! The loose white and green cable are not required and must be isolated.
7
Page
Version 30.01.2013 TF-NTG2
4. Specifications
Operation voltage 10.5 14.8V
Stand-by power drain <2mA
Operation power drain ~60mA
Power consumption ~0,08W
Temperature range -30C to +80C
Weight 44g
Measurements (box only) W x H x D 76 x 27 x 54 mm
5. Technical support
Caraudio-Systems Vertriebs GmbH NavLinkz GmbH
manufacturer/distribution corporate sales/tech dealer-support
Rheinhorststr. 22 Eurotec-Ring 45
D-67071 Ludwigshafen am Rhein D-47445 Moers
phone +49 180 3 907050
email
[email protected]Legal disclaimer: Mentioned company and trademarks, as well as product names/codes are registered
trademarks of their corresponding legal owners.
8
Page
Version 30.01.2013 TF-NTG2
