NORM

EN 12252
Edition: 2014-05-01

LPG equipment and accessories Equipping of

LPG road tankers

Flssiggas-Gerte und Ausrstungsteile Ausrstung von Straentankwagen

fr Flssiggas (LPG)

quipements pour GPL et leurs accessoires quipements des camions

citernes pour GPL

Publisher and printing ICS 43.080.10

Austrian Standards Institute/
sterreichisches Normungsinstitut Identical (IDT) with EN 12252:2014-04
Heinestrae 38, 1020 Wien
Copyright Austrian Standards Institute 2014
All rights reserved. No part of this publication may be Supersedes NORM EN 12252:2012-11
reproduced or utilized in any form or by any means
electronic, mechanical and photocopying or any other responsible Committee 007
data carrier without prior permission! Pressure equipment
AS+ Shop 21.03.2017

E-Mail: [email protected]
Internet: www.austrian-standards.at/terms-of-use
Sale and distribution of national and foreign
standards and technical regulations via
Austrian Standards plus GmbH
Heinestrae 38, 1020 Wien
E-Mail: [email protected]
Internet: www.austrian-standards.at
Webshop: www.austrian-standards.at/webshop
Tel.: +43 1 213 00-300
Fax: +43 1 213 00-818
AS+ Shop 21.03.2017
 EUROPEAN STANDARD EN 12252
NORME EUROPENNE
EUROPISCHE NORM April 2014

ICS 43.080.10 Supersedes EN 12252:2012

English Version

LPG equipment and accessories - Equipping of LPG road

tankers

quipements pour GPL et leurs accessoires - quipements Flssiggas-Gerte und Ausrstungsteile - Ausrstung von
des camions citernes pour GPL Straentankwagen fr Flssiggas (LPG)

This European Standard was approved by CEN on 9 February 2014.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION

COMIT EUROPEN DE NORMALISATION
EUROPISCHES KOMITEE FR NORMUNG
AS+ Shop 21.03.2017

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12252:2014 E
worldwide for CEN national Members.
 EN 12252:2014 (E)

Contents Page
Foreword ..............................................................................................................................................................3
Introduction .........................................................................................................................................................4
1 Scope ......................................................................................................................................................5
2 Normative references ............................................................................................................................5
3 Terms and definitions ...........................................................................................................................7
4 Requirements .........................................................................................................................................9
4.1 General ....................................................................................................................................................9
4.2 Equipment ..............................................................................................................................................9
4.3 Valve access........................................................................................................................................ 10
5 Pressure vessel................................................................................................................................... 10
5.1 Design and manufacture .................................................................................................................... 10
5.2 Mounting of pressure vessel on road tanker ................................................................................... 10
6 Pressure vessel accessories ............................................................................................................. 11
6.1 Required pressure vessel accessories ............................................................................................ 11
6.2 Optional pressure vessel accessories ............................................................................................. 12
7 Vehicle LPG equipment ...................................................................................................................... 12
7.1 Mandatory LPG equipment ................................................................................................................ 12
7.2 Optional LPG equipment .................................................................................................................... 13
8 Equipment specifications .................................................................................................................. 14
8.1 Suitable materials ............................................................................................................................... 14
8.2 Contents gauge ................................................................................................................................... 15
8.3 Pressure gauge ................................................................................................................................... 15
8.4 Temperature gauge............................................................................................................................. 15
8.5 Pump .................................................................................................................................................... 16
8.6 Hoses ................................................................................................................................................... 16
8.7 Hose reel .............................................................................................................................................. 16
8.8 Earth reel ............................................................................................................................................. 17
8.9 Metering system.................................................................................................................................. 17
8.10 Valves ................................................................................................................................................... 17
8.11 Pressure relief valves(PRV) ............................................................................................................... 17
9 Assembly ............................................................................................................................................. 17
9.1 General ................................................................................................................................................. 17
9.2 Welding ................................................................................................................................................ 18
9.3 Flanged connections .......................................................................................................................... 18
9.4 Screwed connections ......................................................................................................................... 18
9.5 External corrosion protection ........................................................................................................... 18
10 Inspection and testing ........................................................................................................................ 18
10.1 General ................................................................................................................................................. 18
10.2 Hydraulic pressure test ...................................................................................................................... 19
10.3 Leak test .............................................................................................................................................. 19
11 Safety systems .................................................................................................................................... 19
11.1 General ................................................................................................................................................. 19
11.2 Emergency Shut-Down system(ESD) ............................................................................................... 20
12 General safety requirements ............................................................................................................. 20
AS+ Shop 21.03.2017

Annex A (normative) Discharge rates for pressure relief valves-Discharge capacity ............................. 21
Annex B (informative) Calculation of mountings of pressure vessel to the chassis ............................... 23
Annex C (informative) Environmental Checklist .......................................................................................... 30
Bibliography ..................................................................................................................................................... 31

2
 EN 12252:2014 (E)

Foreword

This document (EN 12252:2014) has been prepared by Technical Committee CEN/TC 286 Liquefied
Petroleum Gas equipment and accessories, the secretariat of which is held by NSAI.

This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2014 and conflicting national standards shall be withdrawn at
the latest by October 2014.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or] CENELEC shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN 12252:2012.

This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.

This document has been submitted for reference into the technical annexes of the ADR [9].

NOTE These regulations take precedence over any clause of this European Standard. It is emphasised that
RID/ADR/ADN are being revised regularly at intervals of two years which might lead to temporary non-compliances with
the clauses of this European Standard.

The main technical changes of this revision include:

the update of definitions;

the modification of requirements on the primary shut-off system (see 6.1.3);

the modification of the general requirements on the safety system (see 11.1);

the correction of an error in the flow calculation units (see Annex A).

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
AS+ Shop 21.03.2017

3
 EN 12252:2014 (E)

Introduction

This European Standard calls for the use of substances and procedures that may be injurious to health and
also the environment if adequate precautions are not taken. It refers only to technical suitability; it does not
absolve the user from their legal obligations at any stage.

Protection of the environment is a key political issue in Europe and elsewhere around the world. Protection of
the environment in this document is understood in a very broad sense. The phrase is used, for example, in
relation to the total life-cycle aspects of a product on the environment, including expenditure of energy, and
during all phases of its existence, from mining of raw materials, fabrication, packaging, distribution, use,
scrapping, recycling of materials, etc.

NOTE 1 Annex C comprises an environmental checklist which highlights the clauses of this European Standard that
address environmental issues.

Provisions need to be restricted to a general guidance. Limit values are specified in national laws.

It is recommended that manufacturers develop an environmental management policy. For guidance see the
ISO 14000 series [3], [4] and [5]

It has been assumed in the drafting of this European Standard that the execution of its provisions is entrusted
to appropriately qualified and experienced people.

All pressures are gauge pressures unless otherwise stated.

NOTE 2 This European Standard requires measurement of material properties, dimensions and pressures. All such
measurements are subject to a degree of uncertainty due to tolerances in measuring equipment etc. It might be beneficial
to refer to the leaflet measurement uncertainty leaflet SP INFO 2000 27 [10].
AS+ Shop 21.03.2017

4
 EN 12252:2014 (E)

1 Scope

This European Standard specifies equipment and accessories for road tankers used for the transport of
Liquefied Petroleum Gas (LPG) and identifies the equipment that is considered necessary to ensure that
filling, transportation and discharge operations can be carried out safely. It specifies the requirements for the
assembly of the accessories and the vehicle LPG equipment to the road tanker. This European Standard also
identifies additional equipment and accessories that can be used on road tankers carrying LPG.

This European Standard does not preclude the use of alternative designs, materials and equipment testing
which provide the same or a higher level of safety. ADR [9] requires that such alternative technical codes be
recognised by the competent authority, provided that the minimum requirements of section 6.8.2 of ADR [9]
are complied with.

This European Standard does not apply to tank-containers or battery-vehicles used for the transport of
LPG.

2 Normative references

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.

EN 549, Rubber materials for seals and diaphragms for gas appliances and gas equipment

EN 558, Industrial valves Face-to-face and centre-to-face dimensions of metal valves for use in flanged
pipe systems PN and Class designated valves

EN 837-2, Pressure gauges Part 2: Selection and installation recommendations for pressure gauges

EN 1012-1, Compressors and vacuum pumps Safety requirements Part 1: Air compressors

EN 1591-1, Flanges and their joints Design rules for gasketed circular flange connections Part 1:
Calculation method

EN 1762, Rubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and
natural gas up to 25 bar (2,5 MPa) Specification

EN 1983, Industrial valves Steel ball valves

EN 1984, Industrial valves Steel gate valves

EN 10025 (all parts), Hot rolled products of structural steels

EN 10028 (all parts), Flat products made of steels for pressure purposes

EN 10204:2004, Metallic products Types of inspection documents

EN 10216-1, Seamless steel tubes for pressure purposes Technical delivery conditions Part 1: Non-alloy
steel tubes with specified room temperature properties
AS+ Shop 21.03.2017

EN 10217-1, Welded steel tubes for pressure purposes Technical delivery conditions Part 1: Non-alloy
steel tubes with specified room temperature properties

5
 EN 12252:2014 (E)

EN 12074, Welding consumables Quality requirements for manufacture, supply and distribution of
consumables for welding and allied processes

EN 12493, LPG equipment and accessories Welded steel pressure vessels for LPG road tankers
Design and manufacture

EN 12627, Industrial valves Butt welding ends for steel valves

EN 12760, Valves Socket welding ends for steel valves

EN 13175, LPG equipment and accessories Specification and testing for Liquefied Petroleum Gas (LPG)
tank valves and fittings

EN 13709, Industrial valves Steel globe and globe stop and check valves

EN 13789, Industrial valves Cast iron globe valves

EN 13799, LPG equipment and accessories Contents gauges for Liquefied Petroleum Gas (LPG) pressure
vessels

EN 14422, Clamp type coupling assemblies for liquefied petroleum gas (LPG) transfer hoses

EN 14424, Hose fittings with screwed ferrules

EN ISO 148-1, Metallic materials Charpy pendulum impact test Part 1: Test method (ISO 148-1)

EN ISO 3834-2, Quality requirements for fusion welding of metallic materials Part 2: Comprehensive quality
requirements (ISO 3834-2)

EN ISO 3834-3, Quality requirements for fusion welding of metallic materials Part 3: Standard quality
requirements (ISO 3834-3)

EN ISO 9606-1, Qualification testing of welders Fusion welding Part 1: Steels (ISO 9606-1)

EN ISO 10497, Testing of valves Fire type-testing requirements (ISO 10497)

EN ISO 14732, Welding personnel Qualification testing of welding operators and weld setters for
mechanized and automatic welding of metallic materials (ISO 14732)

EN ISO 15609-1, Specification and qualification of welding procedures for metallic materials Welding
procedure specification Part 1: Arc welding (ISO 15609-1)

EN ISO 15614-1, Specification and qualification of welding procedures for metallic materials Welding proce-
dure test Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys (ISO 15614-1)

3 Terms and definitions

For the purposes of this document, the following terms and definitions apply.

3.1
liquefied petroleum gas
AS+ Shop 21.03.2017

LPG
low pressure liquefied gas composed of one or more light hydrocarbons which are assigned to UN 1011,
UN 1075, UN 1965, UN 1969 or UN 1978 only and which consists mainly of propane, propene, butane,
butane isomers and butene with traces of other hydrocarbon gases