ASAE D497.

4 FEB03
Agricultural Machinery Management Data

American Society of Agricultural Engineers

ASAE is a professional and technical organization, of members worldwide, who are

dedicated to advancement of engineering applicable to agricultural, food, and biological
systems. ASAE Standards are consensus documents developed and adopted by the
American Society of Agricultural Engineers to meet standardization needs within the scope
of the Society; principally agricultural field equipment, farmstead equipment, structures, soil
and water resource management, turf and landscape equipment, forest engineering, food
and process engineering, electric power applications, plant and animal environment, and
waste management.

NOTE: ASAE Standards, Engineering Practices, and Data are informational and advisory
only. Their use by anyone engaged in industry or trade is entirely voluntary. The ASAE
assumes no responsibility for results attributable to the application of these ASAE
Standards, Engineering Practices, and Data. Conformity does not ensure compliance with
applicable ordinances, laws and regulations. Prospective users are responsible for
protecting themselves against liability for infringement of patents.

This standard may be designated ANSI/ASAE. If so, this standard is an American National
Standard. Approval of an American National Standard requires verification by ANSI that the
requirements for due process, consensus, and other criteria for approval have been met by
the standards developer.
Consensus is established when, in the judgment of the ANSI Board of Standards Review,
substantial agreement has been reached by directly and materially affected interests.
Substantial agreement means much more than a simple majority, but not necessarily
unanimity. Consensus requires that all views and objections be considered, and that a
concerted effort be made toward their resolution.

CAUTION NOTICE: In the case that this standard is an ANSI/ASAE standard, this American
National Standard may be revised or withdrawn at any time. The procedures of the
American National Standards Institute require that action be taken periodically to reaffirm,
revise, or withdraw this standard. Purchasers of American National Standards may receive
current information on all standards by calling or writing the American National Standards
Institute.

Copyright American Society of Agricultural Engineers. All rights reserved.

ASAE-The Society for engineering in agricultural, food, and biological systems

2950 Niles Rd., St. Joseph, MI 49085-9659, USA ph. 269-429-0300, fax 269-429-3852,
[email protected]
ASAE D497.4 FEB03

Agricultural Machinery Management Data

Developed by the Farm Machinery Management Committee; approved ranging from 0.1 to 0.7, statis radial tire deflections ranging from 10% to
by the Power and Machinery Division Standards Committee; adopted by 30% of the undeflected tire section height, and W / bd values ranging
ASAE February 1963 as ASAE D230; revised December 1965, February from 15 to 55 kN/m2.
1971; revised editorially December 1974; revised December 1977; 3.2.1 Motion resistance, MR, (as defined in ASAE S296) is equal to the
revised editorially September 1979; Table 1 corrected December 1981; difference between gross traction, GT, and net traction, NT:
reconfirmed December 1982; revised December 1983; reconfirmed
December 1988; revised March 1990 and redesignated ASAE D497;
revised editorially December 1990; revised March 1993, March 1994;
revised editorially January 1995; revised November 1996, January 1998;
MR GT NT W 1
Bn
0.04
0.5 s
B n

revised editorially March 1999, February 2000; reaffirmed February 2003.

where:
1 Purpose and scope

1.1 These data include representative values of farm machinery 15
CIb d h
operation parameters as an aid to managers, planners, and designers in B n
estimating the performance of field machines. W b
13
1.2 These data are intended for use with ASAE EP496. Some data are d
reported in equation form to permit use in computer and calculator
mathematical models. Bn is a dimensionless ratio;
1.3 These data report typical values for tractor performance, implement W is the dynamic wheel load in force units normal to the
power requirements, repair and maintenance costs, depreciation, fuel soil surface, kN (lbf);
and oil use, reliability for field operation, probable working days, and CI is the cone index for the soil (see ASAE S313), kPa
timeliness coefficients as measured by experiment, modeling, or survey. (lbf/in.2);
1.4 Where possible, variation in sampled data is reported using the b is the unloaded tire section width, m (in.);
range, a standard deviation, SD, or a coefficient of variation, CV, defined d is the unloaded overall tire diameter, m (in.);
as SD/mean. In a normal distribution 68% of the population should be h is the tire section height, m (in.);
contained in a range of 1 SD about the mean, and 95% will be is the tire deflection, m (in.);
contained in a 2 SD. s is slip (see ASAE S296), decimal.
3.2.1.1 Values of CI and B n for agricultural drive tires ( W / bd
2 Normative references 30 kN/m2) on typical soil surfaces are:
The following standards contain provisions which, through reference in
this text, constitute provisions of this Data. At the time of publication, the Soil Cl (kPa) Bn
editions indicated were valid. All standards are subject to revision, and
parties to agreements based on this Data are encouraged to investigate Hard 1800 80
the possibility of applying the most recent editions of the standards Firm 1200 55
indicated below. Standards organizations maintain registers of currently Tilled 900 40
valid standards. Soft, sandy 450 20
ASAE S296.4 DEC95, Terminology for Traction of Agricultural Tractors, These values are applicable to soils that are not highly compactible.
Self-Propelled Implements and Traction and Transport Devices
ASAE S313.2 DEC94, Soil Cone Penetrometer 3.2.1.2 The motion resistance ratio, , is a ratio of the motion resistance
ASAE S495 DEC94, Uniform Terminology for Agricultural Machinery to dynamic wheel load.
Management MR 1 0.5 s
ASAE EP496.2 MAR94, Agricultural Machinery Management 0.04
W Bn B n
3 Tractor performance 3.2.2 Net traction, NT (as defined in ASAE S296):
3.1 Drawbar performance of tractors depends primarily on engine power,
weight distribution on drive wheels, type of hitch, and soil surface.
Maximum tractive efficiency, TE, is optimized by compromising drive

NT W 0.88 1 e 0.1 B n 1 e 7.5 s
1
Bn

0.5 s
B n
wheel slip, s, and motion resistance, MR. Figure 1 presents typical power where:
relationships for agricultural tractors when properly ballasted for the
desired operating speed. Tractive efficiency can be approximated by the e is the base of natural logarithms.
ratio between PTO power and drawbar power. Four surface conditions
and four types of tractors are included variables. The drive tire size is that 3.2.3 Gross traction, GT (as defined in ASAE S296):
just large enough to carry the expected dynamic loading.
3.2 Single-wheel performance equations for pneumatic tires are useful GT W 0.88 1 e 0.1 B n 1 e 7.5 s 0.04
for design specifications, prediction of vehicle performance, and 3.2.4 Tractive efficiency, TE:
computer simulation of vehicle productivity. The following relationships
apply to bias-ply tires on most agricultural, earthmoving, and forestry NT
TE 1 s
prime movers. The following equations are limited to tires with a b / d ratio GT

ASAE STANDARDS 2003 373

Figure 1 Power relationships for agricultural tractors. Power at a given location in the drive train can be used to estimate power at another location. For
example, PTO power can be estimated from net flywheel power by multiplying the net flywheel power by 0.90. If drawbar power is desired, choose the tractor
type and tractive condition to determine the ratio. To estimate the drawbar power for a four-wheel drive tractor with 224 kW of net flywheel power operating
on firm soil, multiply 224 by 0.90 and 0.78 to arrive at 157.25 kW.

3.3 Fuel efficiency varies by type of fuel and by percent load on the draft required to overcome rolling resistance of the implement are
engine. Typical farm tractor and combine engines above 20% load are included with one exception: for manure injection, motion resistance of
modeled by the equations below. Typical fuel consumption for a specific spreader transport wheels must be added to get total implement draft.
operation is given in L/kWh (gal/hph) where X is the ratio of equivalent 4.1.1 Draft force required to pull many seeding implements and minor
PTO power required by an operation to that maximum available from the tillage tools operated at shallow depths is primarily a function of the width
PTO. These equations model fuel consumptions 15% higher than typical of the implement and the speed at which it is pulled. For tillage tools
Nebraska Tractor Test performance to reflect loss of efficiency under operated at deeper depths, draft also depends upon soil texture, depth,
field conditions. To determine the average fuel consumption of a tractor and geometry of the tool. Typical draft requirements can be calculated as
operating under a range of load conditions, over a period of time, refer
to ASAE EP496.
Gasoline 2.74X 3.15 0.203697X
D F i A B S C S 2 WT
(0.54X 0.62 0.04697X )
Diesel 2.64X 3.91 0.203738X 173
(0.52X 0.77 0.04738X 173 where:
LPG (liquefied petroleum gas) 2.69X 3.41 0.203646X
0.53X 0.62 0.04646X
D is implement draft, N (lbf);
3.4 Oil consumption is defined as the volume per hour of engine F is a dimensionless soil texture adjustment
crankcase oil replaced at the manufacturers recommended change parameter (table1);
interval. Consumption is in L/h (gal/h), where P is the rated engine power i 1 for fine, 2 for medium and 3 for coarse
in kW (hp). textured soils;
Gasoline 0.000566P+0.02487 (0.00011P+0.00657) A , B and C are machine-specific parameters (table1);
Diesel 0.00059P+0.02169 (0.00021P+0.00573) S is field speed, km/h (mile/h).
LPG (liquefied 0.00041P+0.02 (0.00008P+0.00755) W is machine width, m (ft) or number of fows
petroleum gas)
or tools (table1);
T is tillage depth, cm (in.) for major tools, 1
4 Draft and power requirements (dimensionless) for minor tillage tools and
4.1 Draft data are reported as the force required in the horizontal seeding implements.
direction of travel. Both functional draft (soil and crop resistance) and

374 ASAE STANDARDS 2003

 Table 1 Draft parameters and an expected range in drafts estimated by the model parameters for tillage and seeding implements

SI Units English Units

Machine Parameters Machine Parameters Soil Parameters

Width Width Range
Implement units A B C units A B C F1 F2 F3 %

MAJOR TILLAGE TOOLS

Subsoiler/Manure Injector
narrow point tools 226 0.0 1.8 tools 129 0.0 2.7 1.0 0.70 0.45 50
30 cm winged point tools 294 0.0 2.4 tools 167 0.0 3.5 1.0 0.70 0.45 50
Moldboard Plow m 652 0.0 5.1 ft 113 0.0 2.3 1.0 0.70 0.45 40
Chisel Plow
5 cm straight point tools 91 5.4 0.0 tools 52 4.9 0.0 1.0 0.85 0.65 50
7.5 cm shovel/35 cm sweep tools 107 6.3 0.0 tools 61 5.8 0.0 1.0 0.85 0.65 50
10 cm twisted shovel tools 123 7.3 0.0 tools 70 6.7 0.0 1.0 0.85 0.65 50
Sweep Plow
primary tillage m 390 19.0 0.0 ft 68 5.2 0.0 1.0 0.85 0.65 45
secondary tillage m 273 13.3 0.0 ft 48 3.7 0.0 1.0 0.85 0.65 35
Disk Harrow, Tandem
primary tillage m 309 16.0 0.0 ft 53 4.6 0.0 1.0 0.88 0.78 50
secondary tillage m 216 11.2 0.0 ft 37 3.2 0.0 1.0 0.88 0.78 30
Disk Harrow, Offset
primary tillage m 364 18.8 0.0 ft 62 5.4 0.0 1.0 0.88 0.78 50
secondary tillage m 254 13.2 0.0 ft 44 3.8 0.0 1.0 0.88 0.78 30
Disk Gang, Single
primary tillage m 124 6.4 0.0 ft 21 1.8 0.0 1.0 0.88 0.78 25
secondary tillage m 86 4.5 0.0 ft 15 1.3 0.0 1.0 0.88 0.78 20
Coulters
smooth or ripple tools 55 2.7 0.0 tools 31 2.5 0.0 1.0 0.88 0.78 25
bubble or flute tools 66 3.3 0.0 tools 37 3.0 0.0 1.0 0.88 0.78 25
Field Cultivator
primary tillage tools 46 2.8 0.0 tools 26 2.5 0.0 1.0 0.85 0.65 30
secondary tillage tools 32 1.9 0.0 tools 19 1.8 0.0 1.0 0.85 0.65 25
Row Crop Cultivator
S -tine rows 140 7.0 0.0 rows 80 6.4 0.0 1.0 0.85 0.65 15
C -shank rows 260 13.0 0.0 rows 148 11.9 0.0 1.0 0.85 0.65 15
No-till rows 435 21.8 0.0 rows 248 19.9 0.0 1.0 0.85 0.65 20
Rod Weeder m 210 10.7 0.0 ft 37 3.0 0.0 1.0 0.85 0.65 25
Disk-Bedder rows 185 9.5 0.0 rows 106 8.7 0.0 1.0 0.88 0.78 40
MINOR TILLAGE TOOLS
Rotary Hoe m 600 0.0 0.0 ft 41 0.0 0.0 1.0 1.0 1.0 30
Coil Tine Harrow m 250 0.0 0.0 ft 17 0.0 0.0 1.0 1.0 1.0 20
Spike Tooth Harrow m 600 0.0 0.0 ft 40 0.0 0.0 1.0 1.0 1.0 30
Spring Tooth Harrow m 2,000 0.0 0.0 ft 135 0.0 0.0 1.0 1.0 1.0 35
Roller Packer m 600 0.0 0.0 ft 40 0.0 0.0 1.0 1.0 1.0 50
Roller Harrow m 2,600 0.0 0.0 ft 180 0.0 0.0 1.0 1.0 1.0 50
Land Plane m 8,000 0.0 0.0 ft 550 0.0 0.0 1.0 1.0 1.0 45
SEEDING IMPLEMENTS
Row Crop Planter, prepared seedbed
mounted
seeding only rows 500 0.0 0.0 rows 110 0.0 0.0 1.0 1.0 1.0 25
drawn
seeding only rows 900 0.0 0.0 rows 200 0.0 0.0 1.0 1.0 1.0 25
seed, fertilizer, herbicides rows 1,550 0.0 0.0 rows 350 0.0 0.0 1.0 1.0 1.0 25
Row Crop Planter, no-till
seed, fertilizer, herbicides
1 fluted coulter/row rows 1,820 0.0 0.0 rows 410 0.0 0.0 1.0 0.96 0.92 25
Row Crop Planter, zone-till
seed, fertilizer, herbicides
3 fluted coulters/row rows 3,400 0.0 0.0 rows 765 0.0 0.0 1.0 0.94 0.82 35
Grain Drill w/press wheels
2.4 m drill width rows 400 0.0 0.0 rows 90 0.0 0.0 1.0 1.0 1.0 25
2.4 to 3.7 m drill width rows 300 0.0 0.0 rows 67 0.0 0.0 1.0 1.0 1.0 25
3.7 m drill width rows 200 0.0 0.0 rows 25 0.0 1.0 1.0 1.0 1.0 25
Grain Drill, no-till
1 fluted coulter/row rows 720 0.0 0.0 rows 160 0.0 0.0 1.0 0.92 0.79 35
Hoe Drill
primary tillage m 6,100 0.0 0.0 ft 420 0.0 0.0 1.0 1.0 1.0 50
secondary tillage m 2,900 0.0 0.0 ft 200 0.0 0.0 1.0 1.0 1.0 50
Pneumatic Drill m 3,700 0.0 0.0 ft 250 0.0 0.0 1.0 1.0 1.0 50

ASAE STANDARDS 2003 375

4.1.2 Typical, average draft requirement parameters are summarized in For loose, tilled soils and for sands, the motion resistance ratio for a rear
table 1 for most tillage and seeding machines. Each parameter is a wheel operating in the track of a front wheel is about 0.5 of the given
function of tillage tool design. The constant parameter, A , is a function of value. For stubble ground the value is 0.9. For firm surfaces there is no
soil strength while the coefficient of speed parameters, B or C , are reduction.
related to soil bulk density. Soil is categorized as fine, medium, or 4.2.2 Extra width of flotation tires will reduce the coefficient appreciably
coarse. Fine-textured soil is described as high in clay content, medium on soft soils but will increase it for hard soils and concrete.
textured are loamy soils, and coarse textured are sandy soils. Typical 4.2.3 Motion resistance ratios increase with increased tire pressure in
values of all parameters are listed along with an expected range or soft soils. Doubling the tire pressure to 200 kPa causes the coefficient to
variation due to differences in machine design, machine adjustment,
increase to 0.0135 1.27X coefficient at 100 kPa (15 lbf/in.2).
machine age, and site-specific conditions including soil moisture and
residue cover. This range gives the expected variation of average or 4.2.4 An effective motion resistance ratio, e , can be computed for use
typical draft as machine and soil conditions not included in the model on slopes:
vary.
4.2 Motion resistance is an additional draft force that must be included e cos sin
in computing implement power requirements. Values of motion
resistance depend on transport wheel dimensions, tire pressure, soil where:
type, and soil moisture. Soil moistures are assumed to be less than field
capacity for implement operations. Motion resistance ratios are defined in is the motion resistance ratio on level land (see 3.2.1.2);
ASAE S296 and predicted by 3.2.1.2. is the slope. The minus sign is to be used for motion
4.2.1 The values given in 3.2.1 are for single wheels in undisturbed soil. down slopes.

Table 2 Rotary power requirement parameters

Parameter Parameter
a b c a b c Range1)
Machine Type kW kW/m kWh/t hp hp/ft hph/ton %

Baler, small rectangular 2.0 0 1.02) 2.7 0 1.22) 35

Baler, large rectangular bales 4.0 0 1.3 5.4 0 1.6 35
Baler, large round (var. chamber) 4.0 0 1.1 5.4 0 1.3 50
Baler, large round (fix. chamber) 2.5 0 1.8 3.4 0 2.2 50
Beet harvester3) 0 4.2 0 0 1.7 0 50
Beet topper 0 7.3 0 0 3.0 0 30
Combine, small grains 20.0 0 3.64) 26.8 0 4.44) 50
Combine, corn 35.0 0 1.64) 46.9 0 2.04) 30
Cotton picker 0 9.3 0 0 3.8 0 20
Cotton stripper 0 1.9 0 0 0.8 0 20
Feed mixer 0 0 2.3 0 0 2.8 50
Forage blower 0 0 0.9 0 0 1.1 20
Flail harvester, direct-cut 10.0 0 1.1 13.4 0 1.3 40
Forage harvester, corn silage 6.0 0 3.35) 8.0 0 4.05) 40
Forage harvester, wilted alfalfa 6.0 0 4.05) 8.0 0 4.95) 40
Forage harvester, direct-cut 6.0 0 5.75) 8.0 0 6.95) 40
Forage wagon 0 0 0.3 0 0 0.3 40
Grinder mixer 0 0 4.0 0 0 4.9 50
Manure spreader 0 0 0.2 0 0 0.3 50
Mower, cutterbar 0 1.2 0 0 0.5 0 25
Mower, disk 0 5.0 0 0 2.0 0 30
Mower, flail 0 10.0 0 0 4.1 0 40
Mower-conditioner, cutterbar 0 4.5 0 0 1.8 0 30
Mower-conditioner, disk 0 8.0 0 0 3.3 0 30
Potato harvester3) 0 10.7 0 0 4.4 0 30
Potato windrower 0 5.1 0 0 2.1 0 30
Rake, side delivery 0 0.4 0 0 0.2 0 50
Rake, rotary 0 2.0 0 0 0.8 0 50
Tedder 0 1.5 0 0 0.6 0 50
Tub grinder, straw 5.0 0 8.4 6.7 0 10.2 50
Tub grinder, alfalfa hay 5.0 0 3.8 6.7 0 4.6 50
Windrower/swather, small grain 0 1.3 0 0 0.5 0 40

1)
Range in average power requirement due to differences in machine design, machine adjustment, and crop conditions.
2)
Increase by 20% for straw.
3)
Total power requirement must include a draft of 11.6 kN/m (40%) for potato harvesters and 5.6 kN/m (40%) for beet harvesters. A row spacing of 0.86 m for potatoes
and 0.71 m for beets is assumed.
4)
Based upon material-other-than-grain, MOG, throughput for small grains and grain throughput for corn. For a PTO driven machine, reduced parameter a by 10 kW.
5)
Throughput is units of dry matter per hour with a 9 mm (0.35 in.) length of cut. At a specific throughput, a 50% reduction in the length of cut setting or the use of a
recutter screen increases power 25%.

376 ASAE STANDARDS 2003

 Table 3 Field efficiency, field speed, and repair and maintenance cost parameters

Estimated Total life

Field efficiency Field speed life R&M cost Repair factors

Range Typical Range Typical Range Typical % of list

Machine % % mph mph km/h km/h h price RF1 RF2

TRACTORS
2 wheel drive & stationary 12 000 100 0.007 2.0
4 wheel drive & crawler 16 000 80 0.003 2.0

TILLAGE & PLANTING

Moldboard plow 7090 85 3.06.0 4.5 5.010.0 7.0 2 000 100 0.29 1.8
Heavy-duty disk 7090 85 3.56.0 4.5 5.510.0 7.0 2 000 60 0.18 1.7
Tandem disk harrow 7090 80 4.07.0 6.0 6.511.0 10.0 2 000 60 0.18 1.7
(Coulter) chisel plow 7090 85 4.06.5 5.0 6.510.5 8.0 2 000 75 0.28 1.4
Field cultivator 7090 85 5.08.0 7.0 8.013.0 11.0 2 000 70 0.27 1.4
Spring tooth harrow 7090 85 5.08.0 7.0 8.013.0 11.0 2 000 70 0.27 1.4
Roller-packer 7090 85 4.57.5 6.0 7.012.0 10.0 2 000 40 0.16 1.3
Mulcher-packer 7090 80 4.07.0 5.0 6.511.0 8.0 2 000 40 0.16 1.3
Rotary hoe 7085 80 8.014.0 12.0 13.22.5 19.0 2 000 60 0.23 1.4
Row crop cultivator 7090 80 3.07.0 5.0 5.011.0 8.0 2 000 80 0.17 2.2
Rotary tiller 7090 85 1.04.5 3.0 2.07.0 5.0 1 500 80 0.36 2.0
Row crop planter 5075 65 4.07.0 5.5 6.511.0 9.0 1 500 75 0.32 2.1
Grain drill 5580 70 4.07.0 5.0 6.511.0 8.0 1 500 75 0.32 2.1

HARVESTING
Corn picker sheller 6075 65 2.04.0 2.5 3.06.5 4.0 2 000 70 0.14 2.3
Combine 6075 65 2.05.0 3.0 3.06.5 5.0 2 000 60 0.12 2.3
Combine (SP)1) 6580 70 2.05.0 3.0 3.06.5 5.0 3 000 40 0.04 2.1
Mower 7585 80 3.06.0 5.0 5.010.0 8.0 2 000 150 0.46 1.7
Mower (rotary) 7590 80 5.012.0 7.0 8.019.0 11.0 2 000 175 0.44 2.0
Mower-conditioner 7585 80 3.06.0 5.0 5.010.0 8.0 2 500 80 0.18 1.6
Mower-conditioner (rotary) 7590 80 5.012.0 7.0 8.019.0 11.0 2 500 100 0.16 2.0
Windrower (SP) 7085 80 3.08.0 5.0 5.013.0 8.0 3 000 55 0.06 2.0
Side delivery rake 7090 80 4.08.0 6.0 6.513.0 10.0 2 500 60 0.17 1.4
Rectangular baler 6085 75 2.56.0 4.0 4.010.0 6.5 2 000 80 0.23 1.8
Large rectangular baler 7090 80 4.08.0 5.0 6.513.0 8.0 3 000 75 0.10 1.8
Large round baler 5575 65 3.08.0 5.0 5.013.0 8.0 1 500 90 0.43 1.8
Forage harvester 6085 70 1.55.0 3.0 2.58.0 5.0 2 500 65 0.15 1.6
Forage harvester (SP) 6085 70 1.56.0 3.5 2.510.0 5.5 4 000 50 0.03 2.0
Sugar beet harvester 5070 60 4.06.0 5.0 6.510.0 8.0 1 500 100 0.59 1.3
Potato harvester 5570 60 1.54.0 2.5 2.56.5 4.0 2 500 70 0.19 1.4
Cotton picker (SP) 6075 70 2.04.0 3.0 3.06.0 4.5 3 000 80 0.11 1.8

MISCELLANEOUS
Fertilizer spreader 6080 70 5.010.0 7.0 8.016.0 11.0 1 200 80 0.63 1.3
Boom-type sprayer 5080 65 3.07.0 6.5 5.011.5 10.5 1 500 70 0.41 1.3
Air-carrier sprayer 5570 60 2.05.0 3.0 3.08.0 5.0 2 000 60 0.20 1.6
Bean puller-windrower 7090 80 4.07.0 5.0 6.511.5 8.0 2 000 60 0.20 1.6
Beet topper/stalk chopper 7090 80 4.07.0 5.0 6.511.5 8.0 1 200 35 0.28 1.4
Forage blower 1 500 45 0.22 1.8
Forage wagon 2 000 50 0.16 1.6
Wagon 3 000 80 0.19 1.3

1)
SP indicates self-propelled machine.

4.3 Rotary power data are reported as functional power required at the differences in machine design, machine condition and crop
implement engine or tractor PTO shaft. Total power is determined by characteristics. Typical values can be adjusted within this range when
adding the rotary and draft power requirements to the power required to conditions are likely to cause a substantial increase or decrease from the
overcome motion resistance. Typical, average rotary power requirement normal power requirement. Rotary power is determined using these
parameters are summarized in table 2 for 32 major types of agricultural parameters and the relationship defined in ASAE EP496, clause 4.1.2.
machines. The three parameters represent the no-load power
requirement, the power requirement per unit of machine operating width
and the power per unit of material feed rate. Draft requirements are also 5 Machine performance
noted in table 2 for root harvesting machines. Typical values of all 5.1 Performance rates for field machines depend upon achievable field
parameters are listed along with an expected range or variation due to speeds and upon the efficient use of time. Field speeds may be limited

ASAE STANDARDS 2003 377

by heavy yields, rough ground, and adequacy of operator control. Small variation in these data. Repair and maintenance factors based upon the
or irregularly shaped fields, heavy yields, and high capacity machines accumulated use of the machine are given in table 3. Values listed are
may cause a substantial reduction in field efficiency. Typical speeds and for machines used under typical field conditions and speeds. These data
field efficiencies are given in table 3. provide estimates of the average cost for all machines of a given type.
5.2 Slippage of drive wheel, decimal, for ground-driven implements (see The estimate is intended to be within 25% of the actual cost of
3.2.3): maintaining most machines in good working order. Some machines may

require considerably more or less repair than this estimate. A more
1 0.75 complete description of the intended purpose and procedure for use of
Slippage (decimal) ln the data is given in ASAE EP496.
0.3 Cn T 1.2
0.079
rW Cn
where: 7 Reliability
T is the torque due to mechanism operation on the 7.1 Operational reliability is a probability of satisfactory machine function
drive wheel; over any given time period. It is computed as one minus the probability
r is the rolling radius of the drive wheel. of a failure.
7.1.1 Midwestern US reports by farmers (1970) of field failures show the
probability of failure (tractors and implements combined) per 40 ha (100
6 Costs of use acres) of use and the average SD of the total downtime per year for
6.1 Depreciation costs are calculated using remaining value formulas farms of over 200 ha (500 acres).
estimated based on auction sale values of used farm equipment from
1984 to 1993. Calculate remaining value as a percentage of the list price
Breakdown
for farm equipment at the end of n years of age and after h average
Breakdown probability Reliability
hours of use per year using the following equation and the coefficients
time per 40 ha per 40 ha
shown in Table 4.

RVn 100[C1C2(n 0.5)C3(h 0.5)]2 h/yr SD (100 acres) (100 acres)

To include inflation effects, multiply the list price of farm equipment by Tillage 13.6 24.1 0.109 0.89
(1 i ) n where i is the average annual inflation rate. Planting corn 5.3 5.4 0.133 0.87
6.1.1 Remaining values as a percentage of the list price at the end of Planting soybeans 3.7 2.4 0.102 0.90
year n . Row cultivation 5.6 6.3 0.045 0.96
Harvest soybeans, SP 8.2 9.6 0.363 0.64
tractors 68(0.920) n Harvest corn, SP 12.3 12.6 0.323 0.68
all combines, cotton pickers, SP windrowers 64(0.885) n
7.1.2 Breakdown probabilities for machine systems increase with an
balers, forage harvesters, blowers, and SP sprayers 56(0.885) n increase in the size of the farm.
all other field machines 60(0.885) n
Probability of Reliability of
6.2 Repair and maintenance costs are highly variable and unpredictable Crop area, at least one tractor-machine
as to time of occurrence. Surveys of accumulated repair and ha (acres) failure per year system per year
maintenance costs related to accumulated use do show consistent
trends; however, a standard deviation equal to the mean is a typical 0 to 80 (0 to 200) 0.435 0.56
80 to 160 (200 to 400) 0.632 0.30
160 to 240 (400 to 600) 0.713 0.29
240+ (600+) 0.780 0.22
Table 4 Remaining value coefficients

Equipment type C1 C2 C3 7.1.3 Downtime and reliability appear to be independent of use for some
machines while others have shown an increase with accumulated use.
Farm tractors Midwestern US data show: Moldboard plows average 1 hour of downtime
Small <60 kW (80 hp) 0.981 0.093 0.0058 for each 400 ha (1000 acres) of use; row planters average 1 hour of
Medium 60112 kW (80-150 hp) 0.942 0.100 0.0008 downtime for each 250 ha (600 acres) of use; SP combines had little
Large >112 kW (150 hp) 0.976 0.119 0.0019 downtime for the first 365 ha (900 acres) of use. Downtime was a
constant 1 hour for each 30 ha (70 acres) afterward; and tractors had a
Harvest equipment constantly increasing downtime rate with use. The accumulated hours of
Combines 1.132 0.165 0.0079 downtime depend upon the accumulated hours of use, X :
Mowers 0.756 0.067 Spark ignition 0.0000021 X 1.9946
Balers 0.852 0.101
Swathers and all other harvest equipment 0.791 0.091 Diesel 0.0003234 X 1.4173

Tillage equipment
Plows 0.738 0.051 8 Working days, timeliness
Disks and all other tillage equipment 0.891 0.110
8.1 Freezing temperatures, precipitation, excessive deficient soil
moistures, and other weather related factors may limit field machine
Miscellaneous equipment
operations. As weather variability is great, any prediction of the number
Skid-steer loaders and all other vechicles 0.786 0.063 0.0033
of future working days can only be made probabilistically.
Planters 0.883 0.078
Manure spreaders and 8.2 The number of working days in any time period is a function of:
all other miscellaneous equipment 0.943 0.111 climatic region, slope of soil surface, soil type, drainage characteristics,
operation to be performed, and traction and flotation devices.

378 ASAE STANDARDS 2003

 Table 5 Probabilities for a working day

State of South Southern Ontario

Region Central Illinois State of Iowa Southeastern Michigan Carolina Canada Mississippi Delta

Soil Prairie soils State average Clay loam Clay loam Clay loam Clay

Notes 18 yr data 17 yr data Simulation Simulation Simulation (tillage only)

(tillage only) (tillage only) Non-tillage field work
In early spring and late fall, pwd in Simulation Sandy soils can be Start 710 days earlier pwd and pwd for sandy
Iowa and Illinois may be 0.07 greater in (tillage only) worked all months on sandy soils, 0.15 soils some greater in
North and West and 0.07 less in and have higher pwd greater pwd winter and early spring
South and East

Probability level, percent

Biweekly
Average date period 50 90 50 90 50 90 50 90 50 90 50 90

Jan. and Feb. - 0.0 0.0 0.0 0.0 0.0 0.0 0.01 0.0 0.0 0.0 0.07 0.0
Mar. 7 1 0.0 0.0 0.0 0.0 0.0 0.0 - - 0.0 0.0 - -
Mar. 21 2 0.29 0.0 0.0 0.0 0.0 0.0 0.03 0.0 0.0 0.0 0.18 0.0
Apr. 4 3 0.42 0.13 0.39 0.16 0.0 0.0 - - 0.01 0.0 - -
Apr. 18 4 0.47 0.19 0.57 0.38 0.20 0.0 0.29 0.06 0.07 0.0 0.35 0.08

May 2 5 0.54 0.31 0.66 0.48 - - - - 0.62 0.02 - -

May 16 6 0.61 0.34 0.68 0.47 0.61 0.32 0.64 0.37 0.60 0.02 0.58 0.28
May 30 7 0.63 0.40 0.66 0.47 - - - - 0.79 0.16 - -
June 13 8 0.66 0.41 0.69 0.52 0.69 0.42 0.72 0.48 0.77 0.22 0.69 0.39
June 27 9 0.72 0.53 0.74 0.57 - - - - 0.80 0.23 - -

July 11 10 0.72 0.52 0.77 0.64 0.75 0.52 0.67 0.43 - - 0.63 0.25
July 25 11 0.72 0.54 0.80 0.67 - - - - - - - -
Aug. 8 12 0.78 0.64 0.80 0.68 0.74 0.53 0.73 0.51 - - 0.72 0.45
Aug. 22 13 0.86 0.74 0.86 0.79 - - - - - - - -

Sept. 5 14 0.81 0.66 0.79 0.64 0.70 0.35 - - - - - -

Sept. 19 15 0.65 0.42 0.69 0.46 - - 0.72 0.46 - - 0.80 0.58
Oct. 3 16 0.72 0.52 0.71 0.48 0.59 0.26 - - - - - -
Oct. 17 17 0.76 0.58 0.79 0.64 - - 0.61 0.23 - - 0.76 0.42

Nov. 1 18 0.72 0.50 0.75 0.55 0.42 0.06 - - - - - -

Nov. 15 19 0.67 0.47 0.73 0.54 - - 0.33 0.02 - - 0.43 0.0
Nov. 29 20 0.54 0.43 0.82 0.70 0.07 0.0 - - - - - -
Dec. 13 21 - - - - - - 0.02 0.0 - - 0.10 0.0

Adjust for Sundays and holidays by multiplying pwds above by 0.86, 0.82, 0.78, and 0.75 for months 0, 1, 2, and 3 holidays.

8.3 Probabilities for a working day, pwd, are given in table 5 for both is required to include the penalty for both quantity and quality reductions
50% and 90% confidence levels. The probabilities obtained from the in the crop return from prolonged field machinery operations. Timeliness
table are averages for biweekly periods. That is, a probability of 0.4 costs vary widely. Variation is expected among regions, crop varieties,
implies that 0.4 14 or 5.6 working days could be expected in that time of the season, and machine operations. Timeliness costs are
2-week period. If the probability were taken at the 50% level, the 5.6-day essentially zero for those tillage and other operations where there is little
figure would be exceeded in 5 years out of 10. If at the 90% level, the need to finish quickly.
5.6-day figure would be exceeded in 9 years out of 10. 8.6 A timeliness coefficient, K (see ASAE S495, clause 2), is a factor
8.3.1 Two types of field operations are identified soil working operations that permits computation of timeliness costs (see ASAE EP496, clause
such as tillage and seeding and traffic operations where a crop is 8). This factor assumes linear timeliness costs with calendar days and is
processed and the soil needs to be dry enough only to provide machine expressed as a decimal of maximum value of the crop per unit area per
support. The Illinois and Iowa data in table 5 are reports of actual day either before or after the optimum day. These coefficients can be
observed operations and include both types of operations. The other data calculated from measured crop returns as they vary with the timing of
are simulations for tillage operations only. machine operations. For example, if 10-day delay in an operation
8.3.2 Dry western farms and farms under irrigation are likely to have a reduces the eventual return from the crop by 5%, K is calculated as
pwd approaching 1.0. 0.005/10 or 0.005 per unit area per day. The cost of operating on 6 ha
of $100/ha crop by 7 days after the optimum would be
8.4 Persistence is recognized in weather data. Given that a particular
0.00567100=$21. (For the timeless costs for harvesting a total
day is a working day, the succeeding day has about a 0.8 (Midwest)
field, see ASAE EP496, clause 8).
probability of being a working day also. The probability of 5 consecutive
working dates is the pwd for day 1 multiplied by (0.8) 4 . 8.7 Values of K have been determined for several operations (Table 6).
8.5 Timeliness considerations (see ASAE S495, clause 2) are important
to efficient selection of farm machinery. An economic value for timeliness

ASAE STANDARDS 2003 379

Table 6 K values, derived from crop research reports

Operation K

Tillage (depends on whether planting is 0.000-0.010

delayed by prior tillage)

Seeding
Corn
Indiana, Illinois, Iowa, Eastern Nebraska, Eastern Kansas
Available moisture in root zone at planting, cm
10 April 0.010 May 0.000 June 0.002
20 April 0.006 May 0.001 June 0.003
30 April 0.003 May 0.004 June 0.007
Wheat
Utah 0.008
North Dakota 0.007
Soybeans
Wisconsin, May & June 0.005
Missouri, Illinois, June 0.006
Double crop after wheat, Illinois 0.010
Cotton
Lubbock, Texas
April 0.004
May 0.020
Mississippi, April & May 0.007
Barley
Utah 0.008
North Dakota 0.007
Oats
Illinois & Michigan 0.010
Wisconsin, after May 6 0.012
Alabama, Fall 0.000
Utah 0.008
Rape
Manitoba 0.003
Rice
California, May 0.010

Row cultivation
Illinois, soybeans 0.011
Rotary hoeing
Iowa, soybeans 0.028

Harvest
Haymaking, Michigan, June 0.018
Shelled corn, Iowa 0.003
Ear corn, Illinois, after Oct. 26 0.007
Soybeans, Illinois (depends on variety) 0.0060.010
Wheat, Ohio 0.005
Cotton, Alabama 0.002
Rice, California 0.009
Sugar Cane, Queensland Australia
preoptimum 0.002
postoptimum 0.003

380 ASAE STANDARDS 2003