Principles of

Exterior
Drainage

Quick Review
 A. Background
Information
Company Information Sources of Water
NDS leads the exterior Surface water comes from rainfall or irrigation event that does not infiltrate the soil.
drainage industry with
superior quality, design
and service. NDS offers a The Basic Problems
full range of products, Subsurface water and surface water run-off may constitute excess water that is detrimental
including catch basins, to turf and other plant life. This excess water retards plant growth. Surface run-off causes
grates, channel drains, erosion and is retained in surface depressions. Excessive surface and subsurface water will
sewer fittings, flexible create structural damage to foundations, concrete slabs, and other building structures.
couplings, and other
related products.
Indicators of Drainage Problems

PROBLEM SOLUTION PROBLEM SOLUTION

Excess water around the home Catch basins and grates Excess water can drown Catch basins and atrium grates
cracks and damages the remove water from downspouts evergreens, flowers, and other remove excess water to protect
foundation and basement walls. to protect your homes sensitive plants, destroying plant root systems from
foundation and basement walls. your landscape investment. overwater and rot.

PROBLEM SOLUTION PROBLEM SOLUTION

Water from the driveway Channel drains and grates Channel drains and grates Channel drains and grates
enters into your garage. Remove sheets of water moving Remove sheets of water on Remove sheets of water on
Watercreates a slippery across driveways and sidewalks. driveways and sidewalks. patios and backyards.
walkway area. Prevent water from entering the Prevent water from entering Prevent water from entering
garage or foundation areas. the garage or foundation. your home.

2007 NDS, Inc. www.ndspro.com Principles of Exterior Drainage Quick Review

 A. Background Information

Soil Function
Soil acts as a pervious medium that provides passageways for water to move into the
subsurface. The passage of water depends greatly upon the size of the voids in the soil
structure. Granular soils with higher void sizes like sand, allow better water movement
than compact soils with smaller void sizes like clay.
Compaction, from pedestrian and vehicular traffic, can reduce the void size in any
soil. The best way to determine drainage needs in the soil is to probe with a soil augur
3 to 6 deep. Soil should be evaluated to at least 6 below the foundation depth for any
building.
The best way to determine drainage needs in the soil is to probe with a soil auger 3
to 6 deep. Soil should be evaluated to at least 6 below the foundation depth for any
building.

Topography
Slopes have an influence on surface run-off and subsurface ground water. The greater
the slope, the more surface run-off and less soil absorption. Conversely, the lesser the
slope, the more soil absorption and less surface run-off are experienced.

Influence of slope
More surface water runoff,
less soil penetration (center)

Less surface water runoff ,

more soil penetration (right)

Grades and Pipe Slope

The slope or the grade of the surface can be identified by a line level for distances up to
50 feet where precision is not critical. Slope can be calculated using the following formula:
(Rise / Run) x 100 = Slope.

Example: (1 elevation change / 50 distance) x 100= 2% Slope

(1 / 50) x 100 = 2%

Line Level
A line level is a small level bubble enclosed in a metal case, which can be hooked over
a taut string. With the string tied to a stake or held to the ground at one point and
adjusted until it is level, the difference in elevation between the string and the ground
can be measured with a rule.

Distance = 50 Measuring
(1 elevation / 50 distance) x 100 = 2% slope Elevation difference can be
Rule measured with a line level
Stake Taut String Level

Elevation=1

Principles of Exterior Drainage Quick Review 3

 B. Design
Basic Drainage Design
The three basic functions of any storm drainage system are to:
1. Collect water
2. Conduct or move water through pipes
3. Discharge of water.

Checklist for Drainage Design

Analyze the topography of the land
Examine the slope of the grade
Find where water is coming from
Find where water is going
Identify and mark the low spots
Look for downspouts
Look for structures that inhibit water flow
Retaining walls, edging, walkways, etc
Identify a safe discharge point
Select type and size of drainage products to use
Begin your design from the discharge point or retention basin

Best Practices for Drainage Design

Always begin by checking local code requirements
Work from discharge point toward the high spots
Discharged water should not cross any hardscapes
Discharged water must never be directed onto another property
Smooth interior pipe 1% (1.25 per 10 ft.)
Corrugated pipe 2% (2.5 per 10 ft.)
Design a safety outlet in case drain is blocked
Keep it simple!

Surface Drain Design

Catch Basin vs. Channel Drains
Catch basins and inlets are classified as area drains and are ideal for landscaping
applications. Water is directed to the drain by the contours of the landscape. The Basin
or inlet is connected to pipe that conducts the water to the discharge point.
Channel drains are ideal for hardscapes or concrete, brick, and paver flatwork
applications. They operate on the same principle as a roof gutter. The channel drain
acts as a perimeter drain at the edge of the slope. Sheets of water are intercepted by
these linear drains and conducted to the discharge point through pipes.

Design options:
Directional Drainage (left)

Channel Drainage (right)

4 Principles of Exterior Drainage Quick Review

C. Drainage Materials
and Installation
Pipes

Drain Pipe materials

The two most common types of drain pipes for drainage applications are Corrugates
and Sewer/Drain (smooth wall) pipe.
Single wall corrugated pipe is low in cost, flexible, and easy to install, but lacks a
smooth interior wall that would allow the use of a drain snake should it become
clogged. The dual wall corrugated pipe is more expensive and less flexible but has a
smooth interior wall. Since all corrugated pipes are made of High Density
Polyethylene, pipe connections have to be snapped together rather than glued together.
Sewer and Drain pipe is more rigid than any corrugated pipe making it easier to
maintain a continuous slope in critical areas. Its smooth interior gives it ideal flow
characteristics and allows the use of a drain snake when it becomes clogged. Sewer and
Drain pipes are made from Poly Vinyl Chloride, Acryllonitrile Butadiene Stryrene,
Styrene, and polyethylene. Hence, pipe connections can be glued using PVC or ABS
cement.
DWV or Schedule 40 pipe (SCH 40)systems are seldom used to collect water for
drainage projects because of their higher cost. A variety pf adapters are available to
connect DWV or Schedule 40 pipe systems to Sewer and Drain and or Corrugated
pipe systems.
Perforated pipe (holes or slits in the pipe) is used for subsurface drainage and solid
pipe is used to conduct water from surface and/or subsurface drainage systems to a
discharge point.

Types of drain pipes

Smooth wall sewer & drain
pipe (left)

HDPE corrugated pipe (right)

Drain Pipe installation

Gravity is the primary vehicle for conducting the drained water. There must be a
continuous 1/8 per foot or 1% minimum slope for smooth interior pipe. 25% more
slope may be required for corrugated pipe to compensate for the corrugated interior.
Consult an engineer or architect for minimum slope in critical applications.

Principles of Exterior Drainage Quick Review 5

C. Drainage Materials and Installations

Catch Basins

Catch Basins and Inlets materials

Catch basins are used to collect debris from run-off water that may clog drain lines.
The debris is collected in the sump area of a catch basin and should be cleaned out
periodically. A catch basin should be used in areas where debris like mulch, leaves,
sand, silt, or grass clippings are prevalent. NDS basins are flexible by design and easy
to install. Basins range in size from 6 round Spee-D basin and 9x9 to 24x24 square
basins.
Atrium grates are used in landscape areas, planter beds, window wells, or where
debris like mulch and leaves might clog a flat grate. They also have larger open surface
areas to handle more run-off. Round grates are used often in landscape while square
grates are easier to form around in concrete, pavers and other pavement applications.

Surface drain
Grates and basins options

Atrium grate Round grate Square grate

All NDS grates fit directly into corrugated pipe, sewer/drain fittings, or NDS catch
basins, adapters and risers. All NDS catch basin outlets fit directly into Corrugated or
Sewer and Drain pipe and may be adapted to SCH 40 or DWV pipe.
NDS universal outlets allow the installer to customize basins with 3, 4, 6, 8, 10,
or 12 connections in 1, 2, 3 and 4 outlet configurations.
Riser extensions allow the installer to vary the depth of the basin outlets to
maintain the proper slope of the drain line. Additional sump area may be created by
using risers with universal outlets.
Low profile adapters simplify installation in difficult soil conditions, or in areas
where a sump area is not required.

6 Principles of Exterior Drainage Quick Review

 C. Drainage Materials and Installations

Basin and Grate installation

1. Choose the grate size according to amount of rainfall, surface area, and type. It may
be necessary to install more than one grate or basin to accommodate excessive run-off
or a combination of low spots. Use catch basins in applications where it is necessary to
collect debris from run-off water in a sump pump. This helps minimize clogging of
drainage pipes.
2. Locate low spot or any areas where excess water will accumulate.
3. Dig hole deep enough for overall height of basin and grate. Install basin in hole
on top of a firm base. Work from the discharge point back to the grate. Excavate the
base of the trench with a minimum 1% slope to ensure drain pipe slopes to the
discharge point.
4. Connect pipe to the basin and backfill the trench and area around basin.
5. Finish of landscaping surrounding project area.

Surface drains
Catch Basin Drain Inlet
Catch basin (left)
Surface Water Runoff Grate Surface Water Runoff Surface Water Runoff Grate Surface Water Runoff

Drain inlet (right)

Riser
Riser pipe
Sanitary Tee

Water Flow
Water Flow

Catch
Basin Non
Gravel Base Perforated
Gravel Base Pipe

Down Spouts
Down spouts remove a tremendous volume of water from roofs. The down spout can
be directly connected to the drain pipe utilizing a down spout adapter. However, it is
highly recommended that the down spout be placed over a drain basin to prevent
debris from entering and clogging the drain pipe.

Down Spout
With catch basin

Principles of Exterior Drainage Quick Review 7

C. Drainage Materials and Installations

Channel Drains
Channel drains are linear surface drains, connected together to a length appropriate for
the specific installation. Run-off water collected in the drain is discharged to bottom
or end outlets.

Recommended Applications
Driveways
Patios
Swimming pools and spas
Washdown areas
Sidewalks

NDS offers non-sloped channel systems with many advantages over sloped channel
systems.
The NDS non-sloped system is less expensive and simplifies inventory by
eliminating the need to stock various sloping channel sections.
Multiple outlets provide safety through redundancy, should any individual outlet
become clogged.
The channel may be installed level.
Proper flow is assured by use of sloped drain pipe.

8 Principles of Exterior Drainage Quick Review

 C. Drainage Materials and Installations

Channel drain install

Use an overlapping concrete
base for installation next to a
concrete deck. This
installation will pin the
channel against the deck

Installation

A. Standard Installation
1 Excavate a wide and deep trench to accommodate the channel and bedding
concrete.
2 Erect a string line at each end of the drain run, as a guide for laying the channels
to the required level.
3 Begin channel installation at the evacuation or discharge end of the run where the
outlet or outlets are located.
4 Install channel end-to-end PVC cementing sections together.
5 Design bottom or end outlets into the channel run in the appropriate location and
glue to the drain pipe or fittings.
6 PVC cement end caps where appropriate.
7 Using either NDS stakes, 1/2 or 5/8 rebar, or wood stakes, anchor channel to the
trench bed every 24 on each side of channel.
8 Backfill with either concrete, sand, or soil, depending on the application.
9 Pour slab to grade and finish concrete.

Channel drains
Non-vehicular traffic
installation (left)

Vehicular traffic standard

installation (right)

Principles of Exterior Drainage Quick Review 9

C. Drainage Materials and Installations

B. Suspended Installation
1 Suspended installation is ideal for retrofit installations with an existing concrete
slab or new construction where forms can be used to suspend the channels.
2 Prepare the trench excavation.
3 Using 2 x 4 boards, span the width of the trench and bolt the channel grates to
the boards.
4 Pour and compact concrete under and around the channels.
5 Finish to the proper grade.

C.Slurry Installation
1 This installation may be used in lieu of the standard installation.
2 Prepare the trench excavation and pull a string line to the proper elevation.
3 Pour a slurry of concrete in the trench to a depth that will insure at least 4 of
concrete underneath the channels.
4 Lay the channels in the bedding slurry.
5 Check channel alignment and grade again.
6 After the slurry sets, concrete can be poured around the channel and finished to
the proper grade.

Channel drains
Suspended installation (left)

Slurry installation (right)

NOTES
1. Grate must be installed prior to pouring concrete or backfill.
2. Grate should be recessed 1/8 below finish grade in non-traffic applications. Grate
should be recessed 1/4 in traffic applications.
3. In asphalt or hot mastic applications, the channel must be encased in concrete for
strength and to prevent distortion of the channel.
4. Grates should be taped prior to pouring concrete to prevent debris from entering
channel during installation.
5. Refer to load classification chart for proper application.
6. Expansion joints must be provided parallel, but not immediately adjacent to each
side of the drain and crack control joints utilized at right angles to the channel for
installation in concrete.
7. PVC primer and medium body fast set PVC solvent cement must be used to
cement all components.
8. Grate must be installed on channel at all times, except for cleaning.

NDS offers grates, basins, and channel drains in plastic, cast iron, steel, and brass
which are available in the following load classifications. Refer to the NDS Drainage
Product Catalog for individual grate load recommendations.

NOTE: Loads are based on encasing product in concrete.

10 Principles of Exterior Drainage Quick Review

 C. Drainage Materials and Installations

2 Profile Channel Drain

1. Channel
2. Grate
3. Coupling
4. End Cap or End Outlet
5. Bottom Outlet
5
6. Drain Fitting
7. Drain Pipe
3
1 6 7
4

Modular Channel Drain

2. 1. Channel
2. Grate
3
3. End Cap (or End Outlet)
4 4. End Outlet (or End Cap)
5. Bottom Outlet
6. Drain Fitting
1. 7. Drain Pipe

5
6
7

Load Class table

Class A Class C
Loads of 1-60 psi. Recommended for Loads of 176-325 psi. Recommended
pedestrians, bicycles and wheel chair for heavy-duty pneumatic tire forklifts
traffic. and tractor trailers at speeds less than
20 m.p.h., H-20 rated

Class B Class D
Loads of 61-175 psi. Recommended Loads of 326-575 psi. Recommended
for medium-duty pneumatic tire traffic, for heavy-duty hard tire forklifts at
autos and light trucks at speeds less speeds less than 20 m.p.h., H-20 rated.
than 20 m.p.h.

Principles of Exterior Drainage Quick Review 11

C. Drainage Materials and Installations

Outlets
Once the storm water is collected and conveyed in the drain pipe, it must be
discharged to a safe location. Several options are available to discharge water. You can
discharge on-site, into a pond for example; or discharge off site, into the street gutter
or directly into the storm sewer.

Core drilled curb discharge

Water can be discharged
directly into the street by
piping through the curb.
Check local codes for
approval (left)

Culvert discharge
Water can be discharged into
the existing culvert (right)

Pop-Up Drainage Emitter

The pop-up emitter is opened by the hydrostatic pressure of water flowing through the
drain pipe. As flow diminishes, the emitter closes again. The top of the emitter should
be installed at a lower elevation that the invert of the pipe inlet (downspout
connection, connection to a basin, etc.) to ensure proper flow. A 10 length of
perforated pipe installed between the drain pipe and emitter will allow excess water in
the drain pipe to leach into the soil.

Pop-up Emitter
Stormwater is discharged
near the curb or to another
safe area

12 Principles of Exterior Drainage Quick Review

 C. Drainage Materials and Installations

Flo-Well Leaching System

The Flo-Well allows water to be discharged directly into
subsoil. This eliminates the need to install long runs of
pipe to conduct the water to a far-off discharge point. The
Flo-Well disperses the water safely back into the subsoil
within a safe area.

Flo-Well
For gutters and downspouts
(far left)

Install with sump pump

(center)

Eliminates puddles (right)

Soil FLO-WELL
NDS#FWAS24
Flo-Well Installation
Soil FLO-WELL
NDS#FWAS24 Gravel*
4" PVC pipe
Sand 4" PVC pipe Location and number of
ports removed will
determine the rate and
2' dia. 2' dia. direction of leaching. Add
4' dia. 4' dia. gravel around outside of
12" Gravel*
12" Sand Flo-Well unit to increase
Landscape Fabric
leaching capacity
NDS#FWFF67

8" Minimum 8" Minimum

*Class 2 Road Grade

Flo-Well Installation Detail with Landscape Flo-Well Installation Detail in Gravel Backfill
Fabric Wrap in Sand Backfill

Principles of Exterior Drainage Quick Review 13

14 Principles of Exterior Drainage Quick Review
 Fax completed quiz to 1-559-562-9488
Attention Literature Dept.

Principles of Exterior Drainage

Quick Review Quiz
Please complete the following exam and return to NDS. A certificate of completion and an NDS hat will be
sent to you for a 75% or higher score. Good Luck!

Name:
Company: Date:
Company Address:
City: State: Zip:
Phone: Email:

Matching

1. Catch Basin A. These are strainer covers that are installed on the top of a catch basin
or drainage pipe

2. Channel Drains B. Trench filled with coarse aggregate, and most commonly a
perforated pipe, for intercepting and conveying ground water.

3. French Drains C. This is the attachment that run vertically down the building in which
the rain water is routed from the roof-mounted gutters to grade level

4. Grates D. Structure with a grate on top used to collect and divert surface
water to an underground drain pipe system.

5. Gutter Downspout E. Ideal grate configuration for preventing cloggedd inlets due to
leaves, mulch or debris in planters.

6. Atrium grate F. Linear perimeter drain with a grate on top used to collect surface
along flatwork or hardscapes, such as driveways, patios, parking
lots, simming pools, etc.

Multiple Choice

7. When do you need a drainage system? 8. Which type of surface drainage system is ideal for
hardscapes such as driveways, patios and swimming pools?
A. When your in-laws are coming to town
B. Everybody needs a drainage system A. French drains
C. For excess ground water or surface runnoff B. Channel drains
D. Never C. Catch basins & grates
D. Pump & hoses

Principles of Exterior Drainage Quick Review 15

POEDQRI

Catalogs available from NDS:

Drainage Sloped Channel Drip & Micro Irrigation Landscape
Fittings Check Valves, Transition, Compression and Repair Couplings
Equipment Pad Meter Box Valve Box Landscape

Oct2007

Catch Basins & Grates Flexible Couplings Equipment Pads

Channel Drains Flexible Saddles Flo Control Transition Fittings
Flo-Well Stormwater Agrifim Drip Irrigation Flo Control Check Valves
Leaching Systems Grass Pavers Flo Control Ball Valves
Sewer & Drain Fittings Root Barriers Flo Control Repair Couplings
Backwater & Diverter Valves Valve & Meter Boxes Flo Control Saddles

PA R T I A L C L I E N T L I S T

The White House Sheraton Hotels Florida University

Los Angeles Country Club Sherwood Country Club Harbortown Golf Links
Pebble Beach Soldier Field Hyatt Grand Champions
Cypress Point Del Webb & Sun City Country Clubs La Quinta Resort
Spyglass Hill Westin Hotels Marriott Hotels
PGA West Stadium Golf Course Riviera Country Club MGM Grand Hotel & Theme Park
Princeville Golf Course Buchart Gardens Mirage Hotel
Ritz Carlton Disney World Jack La Lane Athletic Clubs
Santa Barbara Zoo Disneyland Olympic Training Center

Address/Telephone www.NDSPRO.com Regional Warehouses:

P.O. Box 339 851 N. Harvard Avenue Lindsay, CA
Lindsay, CA 93247 Fresno, CA
Phone: 800-726-1994 FOR TECHNICAL INFORMATION, CONTACT: Mineola, TX
Fax: 800-726-1998 Technical Services Atlanta, GA
International Phone: 559-562-9888 Seattle, WA
International Fax: 559-562-4488
(888) 825-4716 Philadelphia, PA
e-mail: [email protected] [email protected] Puerto Rico