1106A-70TAG2

149.1kWm (Gross) @ 1500rpm

1100
ElectropaK Series
Basic technical data Centre of gravity, ElectropaK
Forward from rear of block (wet) .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. 476 mm
Number of cylinders .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ..6 Above crankshaft centre line (wet) .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . 176 mm
Cylinder arrangement.. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. In-line Offset to RHS of crankshaft centre line (wet).. .. ... .. ... .. ... .. ... . 16 mm
Cycle .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. 4 stroke
Induction system .. .. ... .. ... .. ... .. . Turbocharged and air charge cooled Performance
Combustion system .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . Direct injection diesel Speed variation at constant load .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. 0.75%
Compression ratio .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . 18.2 : 1 Cyclic irregularity at standby power.. .. ... .. ... .. ... .. ... .. ... .. ... .. 0.028
Bore .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. 105 mm All ratings within .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. 5%
Stroke .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . 135 mm
Cubic capacity .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... 7.01 litres Note: All data based on operation to ISO 3046-1:2002 standard
Direction of rotation .. .. ... .. .. Anticlockwise when viewed from flywheel reference conditions.
Firing order .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. .1, 5, 3, 6, 2, 4 Sound level
Estimated total weight (dry) .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. 788 kg Average sound pressure level for Prime Power @ 1 m .. .. ... TBA dB(A)
Estimated total weight (wet) .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. . 822 kg
Test conditions
Overall dimensions (ElectropaK)
Air temperature .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... 25C
Height .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... 1142 mm Barometric pressure .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . 100 kPa
Length (air cleaner fitted) .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. 1763 mm Relative humidity.. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... ..31.5%
Width .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. 756 mm Air inlet restriction at maximum power.. .. ... .. ... .. ... . 3 kPa (maximum)
Moments of inertia Exhaust back pressure at maximum power.. .. ... .. ... 6 kPa (maximum)
Engine rotational components .. .. ... .. ... .. ... .. ... .. ... .. ... .. 0.27 kgm Fuel temperature.. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. . 40C
Flywheel .. .. ... .. ... .. ... .. ... .. ... 1.26 kgm (SAE2) / 1.13 kgm (SAE3) If the engine is to operate in ambient conditions other than those of the
test conditions, suitable adjustments must be made for these changes.
For full details, contact Perkins Technical Service Department.

1 of 10
Publication No. TPD1857, August 2014.
Copyright 2014 Perkins Engines Company Limited, all rights Perkins Engines Company Limited
reserved. No part of this document may be reproduced in any form Peterborough, PE1 5FQ, United Kingdom
or by any means, without prior written permission of Perkins Engines Tel: +44 (0)1733 583000
Company Limited. The information in this document is substantially Fax: +44 (0)1733 582240
correct at the time of printing and may be altered subsequently. www.perkins.com
General installation
General Installation Units Prime Standby
Gross engine power kW 136 149.1
Gross BMEP kPa 1552.1 1701.6
Mean piston speed metres/s 6.8
ElectropaK net engine power kW 131 144.1
Engine coolant flow (against 35 kPa restriction) litres/min 142
Combustion air flow (at STP) m/min 10.2 10.67
Exhaust gas flow (Max.) m/min 23.78 25.53
Exhaust gas temperature (Max.) in manifold (after turbocharger) C 484
Net engine thermal efficiency % 39.7 39.7
kWe 120 132
Typical genset electrical output (0.8pf 25C)
kVA 150 165
Regenerative power (estimated) kW 6.7
Assumed alternator efficiency % 91.6

Rating definitions
Prime power
Unlimited hours usage, with an average load factor of 80% over each 24 hour period. A 10% overload is available for 1 hour in every 12 hours
operation.
Standby power
Limited to 500 hours annual usage, with an average load factor of 80% of the published Standby power rating over each 24 hour period. Up to 300
hours of annual usage may be run continuously. No overload is permitted on standby power.

Energy balance
Designation Units Prime Standby
Heat in fuel kW 330.2 363.1
Power to cooling fan kW 5.0
Power to coolant and lubricating oil kW 69.1 75.7
Power to exhaust kW 96.6 105.6
Energy to charge coolers kW 17.5 20.5
Power to radiation kW 11 12.2

2 of 10
Publication No. TPD1857, August 2014.
Copyright 2014 Perkins Engines Company Limited, all rights Perkins Engines Company Limited
reserved. No part of this document may be reproduced in any form Peterborough, PE1 5FQ, United Kingdom
or by any means, without prior written permission of Perkins Engines Tel: +44 (0)1733 583000
Company Limited. The information in this document is substantially Fax: +44 (0)1733 582240
correct at the time of printing and may be altered subsequently. www.perkins.com
Cooling system Electrical system
Cooling pack Alternator .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. 8SI
Overall weight (wet) .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. .. 70 kg Alternator voltage.. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ...12 volts
Overall face area.. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ...524800 mm Alternator output .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. .. 65 amps
Width .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. 724 mm Starter.. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... AZF
Height .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... 1090 mm Starter motor voltage .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... 12 volts
Radiator Starter motor power .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. 4.2 kW
Face area.. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. 351200 mm Number of teeth on the flywheel.. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. .126
Number of rows and materials .. .. ... .. ... .. ... .. ... .. . 4 rows, Aluminium Pull-in current of starter motor solenoid
Matrix density and material .. .. ... .. ... .. ... .. 10 fins per inch, Aluminium @ -20C Max. (1) .. .. .. . .. .. . .. .. . .. .. . .. .. . .. pulse signal 12 volts 68 amps
Width of matrix .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. 439 mm
Hold-in current of starter motor solenoid
Height of matrix.. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... . 800 mm
Pressure cap setting (Min.) .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. .100 kPa @ 20C Max. (1) .. .. ... .. ... .. ... .. ... .. ... .. pulse signal 12 volts 20 amps
Engine stop method .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... Solenoid
Charge cooler 1 All leads to rated at 10 amps minimum
Face area.. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . ..173,600 mm
Number of rows and materials .. .. ... .. ... .. ... .. ... .. . 2 rows, Aluminium Cold start recommendations
Matrix density and material .. .. ... .. ... .. ... .. 10 fins per inch, Aluminium Minimum required cranking speed over TDC.. .. ... .. ... .. ... .. ... . 60 rpm
Width of matrix .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. 220 mm
Height of matrix.. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... . 789 mm 5 to -10C -10 to -20C -20 to -25C
Fan Oil 15W40 10W40 5W40
Diameter .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. . 610 mm Starter AZF
Drive ratio .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ..1.25:1
Number of blades.. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... ..7 Battery 2x 900CCA
Material.. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. Nylon
Cranking
Type.. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. .. Pusher 960
current
Air flow @ 1500 rpm.. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. 282 m/min
Power @ 1500 rpm .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... 5 kW Aids None Glowplugs
Coolant Minimum mean
130 rpm 110 rpm 100 rpm
Total system capacity.. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... 21 litres cranking speed
System drawdown capacity .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . ..10%
Engine capacity .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . 9.5 litres Note: Battery capacity is defined by the 20 hour rate
Maximum top tank temperature .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... 110C
Temperature rise across engine Note: I f a change to a low viscosity oil is made, the cranking torque
(Max. rating dependent).. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ..6C - 12C necessary at low ambient temperatures is much reduced. The
Max. permissible external system resistance.. .. ... .. ... .. ... .. ... . 35 kPa starting equipment has been selected to take advantage of
Thermostat operation range.. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. 82C to 93C this. It is important to change to the appropriate multigrade oil
Shutdown switch setting .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. . 118C in anticipation of operating in low ambient temperatures
Coolant pump method of drive .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. . Gear
Recommended coolant immersion heater rating (Min.).. .. ... .. .0.75 kW Exhaust system
Recommended coolant.. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . ..
.. .. ... .. ... .. BS6580 - 1992, ASTM D3306 and ELC coolants to 1E1966 Maximum back pressure - 1500 rpm .. .. ... .. ... .. ... .. ... .. ... .. ..6.0 kPa
Exhaust outlet, internal diameter.. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. 72 mm
Duct allowance
Maximum additional restriction (duct allowance to cooling airflow and
resultant minimum air flow) - Standby power

Description rpm kPa m/min

Duct allowance with inhibited coolant at 53C
Minimum air flow 1500 0.125 252
Duct allowance with inhibited coolant at 46C
Minimum air flow 1500 0.200 234

3 of 10
Publication No. TPD1857, August 2014.
Copyright 2014 Perkins Engines Company Limited, all rights Perkins Engines Company Limited
reserved. No part of this document may be reproduced in any form Peterborough, PE1 5FQ, United Kingdom
or by any means, without prior written permission of Perkins Engines Tel: +44 (0)1733 583000
Company Limited. The information in this document is substantially Fax: +44 (0)1733 582240
correct at the time of printing and may be altered subsequently. www.perkins.com
Fuel system Recommended SAE viscosity
A multigrade oil must be used which conforms to API CH4 or CI4
Injection components ACEA E5 must be used, see illustration below:
Injector.. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. Mechanical
Fuel pump.. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. . DP210 Viscosity grade (Perkins)
Fuel priming 15W-40
Priming pump type .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . Manual
Maximum priming time.. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... 90 seconds 10W-40

Fuel feed 10W-30

Maximum fuel flow .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . ..135 litres/min 5W-40
Maximum suction head at engine fuel pump inlet.. .. ... .. ... .. ... . 10 kPA
Maximum static pressure head .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... 10 kPa 5W-30
Fuel temperature at engine fuel pump inlet .. .. ... .. ... .. ... .. ... .. ... 46C
0W-40
Tolerance on fuel consumption.. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. . 5%
0W-30
Fuel specification
Fuel standard.. .. ... .. ..Various (contact Perkins Technical Department) -50 -40 -30 -20 -10 0 10 20 30 40 50 60
Fuel consumption Ambient Temperature Deg C

Type of operation and application

Load Mountings
g/kWh litres/hr Maximum static bending moment at rear face of block.. .. ... .. ..1130 Nm
110% Prime power 201.1 36.1 Maximum permissible overhung load
on the flywheel .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... . Calculated on request
Prime power 203.3 33.4 Maximum bending moment at rear of flywheel housing.. .. ... .. ... .. ... ..
.. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... 3000 in Shock Nm
75% Prime power 199.7 24.7
50% Prime power 197.9 16.4
Load acceptance
The data below complies with the requirements of classification 3 and 4
25% Prime power 221.1 9.1 of ISO 8528-12 and G2 operating limits stated in ISO 8528-5.
Initial load application: When engine reaches rated speed (15
Induction system seconds maximum after engine starts to crank).

Maximum air intake restriction Description Units

Clean filter .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ..3 kPa % of prime power % 70
Dirty filter.. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .5 kPa
Air filter type .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. ... .. paper element Load kWe 93
Transient frequency deviation % < 10
Lubrication system
Frequency recovery time Seconds 1.4
Maximum total system oil capacity.. .. .. . .. .. . .. .. . .. .. . .. .. . .. . 16.5 litres
Minimum oil capacity in sump .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . 12.4 litres
Maximum oil capacity in sump .. .. ... .. ... .. ... .. ... .. ... .. ... .. 14.9 litres
Maximum engine operating angles -
Front up, front down, right side, left side.. .. ... .. ... .. ... .. ... .. ... .. ... 25
Sump drain plug tapping size .. .. ... .. ... .. ... .. ... .. ... .. ... .3/4 - 16 UNF
Shutdown switch setting (where fitted)
Oil pressure shut down switch.. .. .. . .. .. . .. .. . .. .. . .. .. . .. . 90 kPa Falling
Lubricating oil
Relief valve opening pressure.. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . 430 kPa
Pressure at maximum speed .. .. ... .. ... .. ... .. ... .. ... .. ... .. ... .340 kPa
Maximum continuous oil temperature (in rail).. .. ... .. ... .. ... .. ... .125C
Oil consumption at full load (% of fuel) .. .. ... .. ... .. ... .. ... .. ... .. ... < 0.1

4 of 10
Publication No. TPD1857, August 2014.
Copyright 2014 Perkins Engines Company Limited, all rights Perkins Engines Company Limited
reserved. No part of this document may be reproduced in any form Peterborough, PE1 5FQ, United Kingdom
or by any means, without prior written permission of Perkins Engines Tel: +44 (0)1733 583000
Company Limited. The information in this document is substantially Fax: +44 (0)1733 582240
correct at the time of printing and may be altered subsequently. www.perkins.com
Noise data
Noise levels
Noise level [dB(A)]
Position Prime power Standby
1 97.49 97.53
2 95.15 95.15
3 94.68 94.75
4 93.6 93.6
5 98.57 98.65
6 95.15 95.41

Noise reference level 65 dB(A)

4
5
6

/ octave analysis: TBC Radiator Engine Alternator

1
2
3

5 of 10
Publication No. TPD1857, August 2014.
Copyright 2014 Perkins Engines Company Limited, all rights Perkins Engines Company Limited
reserved. No part of this document may be reproduced in any form Peterborough, PE1 5FQ, United Kingdom
or by any means, without prior written permission of Perkins Engines Tel: +44 (0)1733 583000
Company Limited. The information in this document is substantially Fax: +44 (0)1733 582240
correct at the time of printing and may be altered subsequently. www.perkins.com
1106A-70TAG2 - Left side view

1763 OVERALL

1242.4 443.1

818.7 385.1
LIFTING EYE
619 272.6
OIL FILLER
195 FUEL RETURN 67.9
TO TANK FUEL IN

528.9
361.7
241.1

451
Y Y
88.9
76.2
18.9
234.9

98
4-M12 X 1.75 X 24
47.6

55.6
OIL SAMPLING VALVE
TAPPING-PLUGGED 274.5 156.4
M10 X 1
499.6
DIPSTICK
614
LUB OIL DRAIN PLUG
ON SUMP 701.7 TO 21.0
Flywheel and housing options CUSTOMER MOUNTING HOLE
708
Option Part OILA
Size FILLER Size B Description

The type is SAE 3

1 C0001 & D0004 450.9 153.37
Use on TAG 2 & 4
X
The type is SAE 2
2 C0074 & D0090 489 134.6
Use on TAG 3 & 4

6 of 10
Publication No. TPD1857, August 2014.
Copyright 2014 Perkins Engines Company Limited, all rights Perkins Engines Company Limited
reserved. No part of this document may be reproduced in any form Peterborough, PE1 5FQ, United Kingdom
or by any means, without prior written permission of Perkins Engines Tel: +44 (0)1733 583000
Company Limited. The information in this document is substantially Fax: +44 (0)1733 582240
correct at the time of printing and may be altered subsequently. www.perkins.com
1106A-70TAG2 - Front view

1763 OVERALL

1242.4 443.1

818.7 385.1
LIFTING EYE
619 272.6
OIL FILLER
195 FUEL RETURN 67.9
TO TANK FUEL IN

528.9
361.7
241.1

451
Y Y
88.9
76.2
18.9
234.9

98
4-M12 X 1.75 X 24
47.6

55.6
OIL SAMPLING VALVE
TAPPING-PLUGGED 274.5 156.4
M10 X 1
499.6
DIPSTICK
614
LUB OIL DRAIN PLUG
ON SUMP 701.7 TO 21.0
CUSTOMER MOUNTING HOLE
708
OIL FILLER

7 of 10
Publication No. TPD1857, August 2014.
Copyright 2014 Perkins Engines Company Limited, all rights Perkins Engines Company Limited
reserved. No part of this document may be reproduced in any form Peterborough, PE1 5FQ, United Kingdom
or by any means, without prior written permission of Perkins Engines Tel: +44 (0)1733 583000
Company Limited. The information in this document is substantially Fax: +44 (0)1733 582240
correct at the time of printing and may be altered subsequently. www.perkins.com
1106A-70TAG2 - Right side view

1763 OVERALL

1242.4 443.1

818.7 385.1
LIFTING EYE
619 272.6
OIL FILLER
195 FUEL RETURN 67.9
TO TANK FUEL IN

528.9
361.7
241.1

451
Y Y
88.9
76.2
18.9
234.9

98
4-M12 X 1.75 X 24
47.6

55.6
OIL SAMPLING VALVE
TAPPING-PLUGGED 274.5 156.4
M10 X 1
499.6
DIPSTICK
614
LUB OIL DRAIN PLUG
ON SUMP 701.7 TO 21.0
CUSTOMER MOUNTING HOLE
708
OIL FILLER

8 of 10
Publication No. TPD1857, August 2014.
Copyright 2014 Perkins Engines Company Limited, all rights Perkins Engines Company Limited
reserved. No part of this document may be reproduced in any form Peterborough, PE1 5FQ, United Kingdom
or by any means, without prior written permission of Perkins Engines Tel: +44 (0)1733 583000
Company Limited. The information in this document is substantially Fax: +44 (0)1733 582240
correct at the time of printing and may be altered subsequently. www.perkins.com
1106A-70TAG2 - Rear view

1763 OVERALL

1242.4 443.1

818.7 385.1
LIFTING EYE
619 272.6 SIZE C
OIL FILLER
195 FUEL RETURN 67.9
TO TANK FUEL IN

SIZE D

SIZE E

SIZE F

528.9
361.7
241.1

451
Y Y
88.9
76.2
18.9
234.9

98
4-M12 X 1.75 X 24
47.6

55.6
OIL SAMPLING VALVE
TAPPING-PLUGGED 274.5 156.4
M10 X 1
499.6
DIPSTICK
614
LUB OIL DRAIN PLUG
ON SUMP 701.7 TO 21.0
CUSTOMER MOUNTING HOLE
Option Part Size C Size D 708 Size E Size F
OIL FILLER
12- M10 x 1.5 x 20 8- 3/8 - 24 UNF x 25.4 8- 3/8 - 24 UNF x 25.4 8- M8 x 1.25 x 14.3
C0001 &
1 EQUISPACED ON EQUISPACED ON EQUISPACED ON EQUISPACED ON
D0004
428.63 P.C.DIA 333.38 P.C.DIA 295.28 P.C.DIA 203.2 P.C.DIA
X
12- M10 x 1.5 x 20 8- M10 x 1.5 x 25.4
C0074 &
2 EQUISPACED ON EQUISPACED ON
D0090
466.725 P.C.DIA 333.38 P.C.DIA

9 of 10
Publication No. TPD1857, August 2014.
Copyright 2014 Perkins Engines Company Limited, all rights Perkins Engines Company Limited
reserved. No part of this document may be reproduced in any form Peterborough, PE1 5FQ, United Kingdom
or by any means, without prior written permission of Perkins Engines Tel: +44 (0)1733 583000
Company Limited. The information in this document is substantially Fax: +44 (0)1733 582240
correct at the time of printing and may be altered subsequently. www.perkins.com
1106A-70TAG2 - Plan view

1763 OVERALL

1242.4 443.1

818.7 385.1
LIFTING EYE
619 272.6
OIL FILLER
195 FUEL RETURN 67.9
TO TANK FUEL IN

528.9
361.7
241.1

451
Y Y
88.9
76.2
18.9
234.9

98
4-M12 X 1.75 X 24
47.6

55.6
OIL SAMPLING VALVE
TAPPING-PLUGGED 274.5 156.4
M10 X 1
499.6
DIPSTICK
614
LUB OIL DRAIN PLUG
ON SUMP 701.7 TO 21.0
CUSTOMER MOUNTING HOLE
708
OIL FILLER

10 of 10
Publication No. TPD1857, August 2014.
Copyright 2014 Perkins Engines Company Limited, all rights Perkins Engines Company Limited
reserved. No part of this document may be reproduced in any form Peterborough, PE1 5FQ, United Kingdom
or by any means, without prior written permission of Perkins Engines Tel: +44 (0)1733 583000
Company Limited. The information in this document is substantially Fax: +44 (0)1733 582240
correct at the time of printing and may be altered subsequently. www.perkins.com