2.3.1.5 Packet Tracer - Configuring PVST Instructions PDF

Packet Tracer Configuring PVST+
Topology
Addressing Table
Device Interface IP Address Subnet Mask Default Gateway
S1 VLAN 99 172.31.99.1 255.255.255.0 N/A

S2 VLAN 99 172.31.99.2 255.255.255.0 N/A
S3 VLAN 99 172.31.99.3 255.255.255.0 N/A
PC1 NIC 172.31.10.21 255.255.255.0 172.31.10.254
PC2 NIC 172.31.20.22 255.255.255.0 172.31.20.254
PC3 NIC 172.31.30.23 255.255.255.0 172.31.30.254
Switch Port Assignment Specifications
Ports Assignments Network
S1 F0/6 VLAN 30 172.17.30.0/24

S2 F0/18 VLAN 20 172.17.20.0/24
S3 F0/11 VLAN 10 172.17.10.0/24
Objectives
Part 1: Configure VLANs
Part 2: Configure Spanning Tree PVST+ and Load Balancing
Part 3: Configure PortFast and BPDU Guard
2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 3
Background
In this activity, you will configure VLANs and trunks, and examine and configure the Spanning Tree Protocol
primary and secondary root bridges. You will also optimize the switched topology using PVST+, PortFast, and
BPDU guard.
Part 1: Configure VLANs

Step 1: Enable the user ports on S1, S2, and S3 in access mode.
Refer to the topology diagram to determine which switch ports (S1, S2, and S3) are activated for end-user
device access. These three ports will be configured for access mode and enabled with the no shutdown
command.
Step 2: Create VLANs.

Using the appropriate command, create VLANs 10, 20, 30, 40, 50, 60, 70, 80, and 99 on all of the switches.
Step 3: Assign VLANs to switch ports.

Port assignments are listed in the table at the beginning of the activity. Save your configurations after
assigning switch ports to the VLANs.
Step 4: Verify the VLANs.

Use the show vlan brief command on all switches to verify that all VLANs are registered in the VLAN table.
Step 5: Assign the trunks to native VLAN 99.

Use the appropriate command to configure ports F0/1 to F0/4 on each switch as trunk ports, and assign these
trunk ports to native VLAN 99.
Step 6: Configure the management interface on all three switches with an address.
Verify that the switches are correctly configured by pinging between them.
Part 2: Configure Spanning Tree PVST+ and Load Balancing

Because there is a separate instance of the spanning tree for every active VLAN, a separate root election is
conducted for each instance. If the default switch priorities are used in root selection, the same root is elected
for every spanning tree instance, as we have seen. This could lead to an inferior design. Some reasons to
control the selection of the root switch include:
The root switch is responsible for generating BPDUs for STP 802.1D and is the focal point for spanning
tree to control traffic. The root switch must be capable of handling this additional load.
The placement of the root defines the active switched paths in the network. Random placement is likely to
lead to suboptimal paths. Ideally the root is in the distribution layer.
Consider the topology used in this activity. Of the six trunks configured, only three are carrying traffic.
While this prevents loops, it is a waste of resources. Because the root can be defined on the basis of the
VLAN, you can have some ports blocking for one VLAN and forwarding for another. This is demonstrated
below.
Step 1: Configure STP mode.

Use the spanning-tree mode command to configure the switches so they use PVST as the STP mode.
Step 2: Configure Spanning Tree PVST+ load balancing.

a. Configure S1 to be the primary root for VLANs 1, 10, 30, 50, and 70. Configure S3 to be the primary root
for VLANs 20, 40, 60, 80, and 99. Configure S2 to be the secondary root for all VLANs.
b. Verify your configurations using the show spanning-tree command.
Part 3: Configure PortFast and BPDU Guard

Step 1: Configure PortFast on the switches.
PortFast causes a port to enter the forwarding state almost immediately by dramatically decreasing the time
of the listening and learning states. PortFast minimizes the time it takes for the server or workstation to come
online. Configure PortFast on the switch interfaces that are connected to PCs.
Step 2: Configure BPDU guard on the switches.

The STP PortFast BPDU guard enhancement allows network designers to enforce the STP domain borders
and keep the active topology predictable. The devices behind the ports that have STP PortFast enabled are
unable to influence the STP topology. At the reception of BPDUs, the BPDU guard operation disables the port
that has PortFast configured. The BPDU guard transitions the port into the err-disable state, and a message
appears on the console. Configure BPDU guard on switch interfaces that are connected to PCs.
Step 3: Verify your configuration.

Use the show running-configuration command to verify your configuration.

2.3.1.5 Packet Tracer - Configuring PVST Instructions PDF

Uploaded by

Copyright:

Available Formats

2.3.1.5 Packet Tracer - Configuring PVST Instructions PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

2.3.1.5 Packet Tracer - Configuring PVST Instructions PDF

Uploaded by

Copyright:

Available Formats

Packet Tracer Configuring PVST+

Device Interface IP Address Subnet Mask Default Gateway

S1 VLAN 99 172.31.99.1 255.255.255.0 N/A

Switch Port Assignment Specifications

Ports Assignments Network

S1 F0/6 VLAN 30 172.17.30.0/24

Part 1: Configure VLANs

Step 2: Create VLANs.

Step 3: Assign VLANs to switch ports.

Step 4: Verify the VLANs.

Step 5: Assign the trunks to native VLAN 99.

Part 2: Configure Spanning Tree PVST+ and Load Balancing

Step 1: Configure STP mode.

Step 2: Configure Spanning Tree PVST+ load balancing.

Part 3: Configure PortFast and BPDU Guard

Step 2: Configure BPDU guard on the switches.

Step 3: Verify your configuration.

You might also like