Malfunction in Speedometer: Wiring Diagram

Download as pdf or txt
Download as pdf or txt
You are on page 1of 4

051240

DIAGNOSTICS COMBINATION METER 05KC001

MALFUNCTION IN SPEEDOMETER

WIRING DIAGRAM

Combination
Skid Control ECU Meter Assy

26 (12) 4 27
SP1 S1 IH1 C8
WG WG

( ): VSC

I40714

INSPECTION PROCEDURE
1 READ VALUE OF INTELLIGENT TESTER II(VEHICLE SPEED SIGNAL)

(a) Operate the intelligent tester II according to the steps on the display and select DATA LIST.
ABS:
Measurement Item/
Item Normal Condition Diagnostic Note
Range (Display)
Vehicle speed / Min.: 0 km/h (0 Almost same as actual speed
(FR/FL/RR/RL) Wheel Speed
mph), Max.: 326 km/h (202 mph) (When driving)

OK:
Vehicle speed displayed on the tester is almost the same as the actual vehicle speed.
NG GO TO BRAKE CONTROL SYSTEM
(SEE PAGE 05606)

OK

AVENSIS VERSO/PICNIC Supplement (RM1032E)


051241
DIAGNOSTICS COMBINATION METER

2 INSPECT COMBINATION METER ASSY

Wire Harness View: INSPECTION USING OSCILLOSCOPE


(a) Check the input signal waveform.
(1) Remove the combination meter assy.
(2) Connect the oscilloscope to terminal C827 and
body ground.
(3) Start the engine.

C827
I31176

(4) Check the signal waveform according to the condi-


tion (s) in the table below.
Item Condition
Tool setting 5 V/ DIV, 20 ms/ DIV
Vehicle condition Driving at approx. 20 km/h (12 mph)
GND OK:
As shown in the illustration
HINT:
A05135 As vehicle speed increases, the cycle of the signal waveform
narrows.

OK A
NG (w/ VSC) B
NG (w/ ABS) C

B Go to step 3

C Go to step 5

REPLACE COMBINATION METER ASSY

AVENSIS VERSO/PICNIC Supplement (RM1032E)


051242
DIAGNOSTICS COMBINATION METER

3 CHECK HARNESS AND CONNECTOR(BETWEEN ABS&TRACTION ACTUATOR


ASSY AND COMBINATION METER ASSY)

(a) Disconnect the C8 and S1 connectors.


ABS&Traction Actuator Assy (VSC)
(b) Measure the resistance according to the value(s) in the
Wire Harness View: S112
table below.
Standard:
Tester Connection Specified Condition
C827 S112 Below 1 W
C827 Body ground 10 kW or higher

Combination Meter Assy


Wire Harness View:

C827
NG REPAIR OR REPLACE HARNESS OR
I40717 CONNECTOR

OK

4 INSPECT ABS&TRACTION ACTUATOR ASSY(VSC)

ABS&Traction Actuator Assy (VSC) (a) Disconnect the S1 connector.


Wire Harness View: (b) Measure the voltage according to the value(s) in the table
S112 below.
Standard:
Tester Connection Condition Specified Condition
S112 Body ground Ignition switch ON 10 to 14 V

I40133 NG REPLACE COMBINATION METER ASSY

OK

GO TO BRAKE CONTROL SYSTEM(SEE PAGE 05606)

AVENSIS VERSO/PICNIC Supplement (RM1032E)


051243
DIAGNOSTICS COMBINATION METER

5 CHECK HARNESS AND CONNECTOR(BETWEEN BRAKE ACTUATOR ASSY AND


COMBINATION METER ASSY)

Brake Actuator Assy (ABS) (a) Disconnect the C8 and S1 connectors.


Wire Harness View: (b) Measure the resistance according to the value(s) in the
table below.
Standard:
Tester Connection Specified Condition
C827 S126 Below 1 W
C827 Body ground 10 kW or higher

S126
Combination Meter Assy
Wire Harness View:

C827
NG REPAIR OR REPLACE HARNESS OR
I40718 CONNECTOR

OK

6 INSPECT BRAKE ACTUATOR ASSY(ABS)

Brake Actuator Assy (ABS) (a) Disconnect the S1 connector.


Wire Harness View: (b) Measure the voltage according to the value(s) in the table
below.
Standard:
Tester Connection Condition Specified Condition
S126 Body ground Ignition switch ON 10 to 14 V

S126 I40719 NG REPAIR OR REPLACE HARNESS OR


CONNECTOR

OK

GO TO BRAKE CONTROL SYSTEM(SEE PAGE 05606)

AVENSIS VERSO/PICNIC Supplement (RM1032E)

You might also like