Product Data Sheet

Edition 2014-08_1

Sika Microcrete-217

Sika Microcrete-217
Self-compacting concrete for formwork repairs

Product Sika Microcrete-217 is a pre-bagged self-compacting concrete. It has very good
flow properties and has been specifically developed to reduce heat generation. As
Description such, large volume repairs may be performed without addition of aggregates.
Construction

Sika Microcrete-217 contains blended cement, graded aggregates and additives
which give rise to controlled expansion in both the plastic and hardened states.

Uses Sika Microcrete-217 is suitable for structural repairs to bridges, columns, etc. It is
also conducive for use in the following repair works where single placing is in
excess of 50 mm thickness:
Bridge columns and beams
Concrete piling
Dams
Grouting applications

Sika Microcrete-217 can be applied by gravity pour.

Characteristics / Pre-bagged at the factory / consistent quality

Advantages Easy to mix and apply
Good flow characteristics
Suitable for large repairs
Non-toxic and non-corrosive
Impact and vibration resistant
Placing thickness up to 300 mm

Product Data
Appearance / Colour Pre-bagged concrete grey powder

Packaging 25 kg bags

Storage Conditions / 6 months from the date of production if stored properly in original, unopened and
Shelf Life undamaged sealed packaging in dry conditions. Keep away from direct sunlight.

Density ~ 2-3 kg/ltr (freshly mixed mortar)

Aggregate Size 10mm max.

1
Sika Microcrete-217 1/3
Mechanical / Physical
Properties

Typical Results Tests carried out at +25C

Description Results
Flow Spread > 650 mm

L-Box > 80%

2
Compressive Strength, N/mm at 7 days ~25
at 28 days ~45

The above tests were conducted under laboratory conditions in accordance to the
following standards:
Flow Spread EFNARC
Bleeding ASTM C940
Compressive Strength MS 522: Part 2: 1989
L-Box EFNARC

System Information

Application Details

Substrate Preparation Concrete surfaces should be clean, free from oil, grease, laitance and loosely
adhering particles. A few hours prior to grouting / repair work, the substrate must
be properly saturated by filling the formwork with clean water. Drain away the water
prior to starting work.
Metal surface (iron and steel) should be free from scale, rust, oil and grease. For

marine structures, it is recommended that the steel bars be protected with SikaTop

Armatec -110 EpoCem (refer to Product Data Sheet for details).
Saw cut the extremities for the repair to at least 10 mm depth to prevent feather
edging. Exposed re-bars should have clearance of at least 30 mm.

Formwork Preparation The formwork must be constructed to be leak proof, as Sika Microcrete-217 is a
free flowing material. However, it should include outlets to drain out water used for
pre-soaking the substrate. Adequate air release shall be installed. If repair is
carried out at the soffits, provision for air venting through the substrate must be
provided.

Application Conditions /
Limitations

Application At temperatures of +20C and below, setting time and strength development will be
Temperature slower.

Application Instructions

Mix Ratio Flowable consistency: 3.0 ltr - 3.3 ltr of water/25 kg bag

Mixing Sika Microcrete-217 should be mechanically mixed in a clean container using a
heavy-duty drill and paddle or a forced-action mixer. According to the mixing ratio

place first the water into the clean mixing container and add Sika Microcrete-217
slowly while mixing. Ensure a minimum mixing time of 3 minutes.
During mixing, the mortar will initially have a visibly stiff appearance, but upon
continuous stirring, it will become free-flowing. Hence, do not add more water than
the recommended maximum mixing ratio.
The speed of the mixer should not exceed 500 rpm to minimise air entrainment.

2
Sika Microcrete-217 2/3
 Application Method / After mixing, stir lightly with a spatula for a few seconds to release any entrapped
Tools air. Pour the free flowing mortar immediately into the prepared formwork. Place the
mortar within 40 minutes after mixing. Pour the mixed material to the lowest point in
the formwork. Care shall be taken not to entrap any air during the repair operation
as this may affect the bonding properties of the repair.

When placing Sika Microcrete-217 over a large area, it is important to maintain
continuous flow throughout. Work sequence must be properly organised to ensure
uninterrupted flow.

Pot Life 40 minutes min. (at +30C)

Cleaning of Tools Clean all tools and application equipment with water immediately after use.
Hardened and/or cured material can only be mechanically removed.

Curing Details
Construction

Curing Exposed surfaces should be kept to a minimum and cured with appropriate curing
methods as soon as the mortar has hardened.
The formwork can be stripped after at least 3 days.

Upon removal of the formwork, cure the repaired areas immediately with Antisol E

curing compound if no further treatment is required or Antisol A curing compound if
a protective coating is to be applied (consult our Technical Service Department)
refer to the respective Product Data Sheet for application rate and method.

Value Base All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.

Health and Safety For information and advice on the safe handling, storage and disposal of chemical
products, users shall refer to the most recent Material Safety Data Sheet (available
Information upon request) containing physical, ecological, toxicological and other safety-related
data.

Legal Note The information, and, in particular, the recommendations relating to the application
and end-use of Sika products, are given in good faith based on Sika's current
knowledge and experience of the products when properly stored, handled and
applied under normal conditions in accordance with Sikas recommendations. In
practice, the differences in materials, substrates and actual site conditions are such
that no warranty in respect of merchantability or of fitness for a particular purpose,
nor any liability arising out of any legal relationship whatsoever, can be inferred
either from this information, or from any written recommendations, or from any other
advice offered. The user of the product must test the products suitability for the
intended application and purpose. Sika reserves the right to change the properties
of its products. The proprietary rights of third parties must be observed. All orders
are accepted subject to our current terms of sale and delivery. Users must always
refer to the most recent issue of the local Product Data Sheet for the product
concerned, copies of which will be supplied on request.

Sika Singapore Pte Ltd Phone: +65 6777 2811

200 Pandan Loop, 06-02 Pantech 21 Fax: +65 6779 6200
Singapore 128388 e-mail: [email protected]
SINGAPORE www.sika.com.sg

Sika Kimia Sdn Bhd Phone: +606-7991762

Lot 689 Nilai Industrial Estate Fax: +606-7991980
71800 Nilai, Negeri Sembilan DK e-mail: [email protected]
MALAYSIA www.sika.com.my

3
Sika Microcrete-217 3/3