Scribd
Upload
111 views2 pages

HCL Galvanize

HCl reacts violently with zinc and steel. Even when neutralized, residual chlorine can remove zinc coatings and rust steel if not properly rinsed. Stainless steel alloys containing molybdenum like 317 are more resistant to wet chloride than standard 316L. Tin plating provides better protection than zinc in chloride environments but will eventually degrade from abrasion. The correct material should be selected based on the intended service conditions. Valmet offers sensors and measurement recipes to determine HCl concentration by measuring conductivity and temperature. The sensors are maintenance-free and accurate and can withstand temperature fluctuations in demanding applications. HCl is commonly used at 3-15% strength for steel pickling and cleaning before galvan

Uploaded by

hanazahr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
111 views2 pages

HCL Galvanize

HCl reacts violently with zinc and steel. Even when neutralized, residual chlorine can remove zinc coatings and rust steel if not properly rinsed. Stainless steel alloys containing molybdenum like 317 are more resistant to wet chloride than standard 316L. Tin plating provides better protection than zinc in chloride environments but will eventually degrade from abrasion. The correct material should be selected based on the intended service conditions. Valmet offers sensors and measurement recipes to determine HCl concentration by measuring conductivity and temperature. The sensors are maintenance-free and accurate and can withstand temperature fluctuations in demanding applications. HCl is commonly used at 3-15% strength for steel pickling and cleaning before galvan

Uploaded by

hanazahr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

HCl reacts furiously with Zinc (Galvanize), and reacts rapidly with steel (pickling

process). Even when neutralized, the Cl is still reactive towards both Zinc & Steel,
and will, in a short period of time, completely remove the Zinc and start rusting the
steel if not copiously rinsed and dried, and even re-chromated. Big hassle in the
field. As for Stainless Steel cable, even 316L is not recommended for wet Chloride
service. You must use a Molybdenum stainless such as 317, or other such Moly
containing alloy such as Haynes C276. They are not as strong but will withstand the
wet chloride environment.

Another option is Tin plated cable instead of Zinc. Tin holds up much better than
Zinc in chloride. Platers know that you strip Tin in Fluoboric/peroxide mix; HCl won't
do that job. But as the cable is used It will get scratched & abraded, so any coating
will eventually give out and put whatever depends on that cable at risk. Therefore
the correct grade of material should be selected for the intended service.

Dave Kinghorn
Chemical Engineer

SUNNYvale,
California

Hydrochloric acid (HCl) concentration


measurements
The concentration of hydrochloric acid (HCl) is calculated by measuring the
conductivity and temperature of the acid. Valmet offers readymade concentration
measurement recipes for various hydrochloric acid concentrations.

The sensors are readily calibrated and the cell constant is stored in the sensor
memory. All you have to do is install the sensor in the process pipe and power up
the measurement.

Valmet Concentration measurement is m

aintenance free and accurate thanks to 4 electrode technology. The sensors are
designed to withstand rabid temperature changes have a long lifetime even in the
most demanding applications.

TECHNICAL DATA

Materials PTFE and W 1.4404 (AISI 316L)

Pressure 12 bar at 120o

Temp. Sensor Pt 1000 (IEC 751 class A)


Solution Measuring Range Temperature

HCl 0-15% 10-80 oC

HCl 25-40% 0-60 oC

HCl 30-60% 15-45 oC

Hydrochloric acid is often used for cleaning steel prior to galvanizing, and at typical
strengths of 3-15%. Its common to start a new tank at a high strength (say 15%)
then as the tank ages the acid concentration reduces as it converts iron oxides to
iron chloride.
But HCl concentration is not the only important parameter. Concentration of iron
chloride is also important, as well as temperature.
Prof Kleingarn did a lot of research on this and produced a graph of concentrations
of HCl and FeCl2 to enable operators to optimise pickling time.

Geoff Crowley
galvanizing & powder coating shop
Glasgow, Scotland

You might also like