Pressure Piping Systems Technical Manual

Volume I:
Pressure Piping
Systems Design
Municipal Technical
Manual Series
F O U R T H E D I T I O N
Blue Brute Piping Systems

Bionax Piping Systems
IPEX Centurion Piping Systems
IPEX Fusible TM Pipe
TerraBrute CR Piping Systems
CycleTough Piping Systems
Blue904 TM Water Service Tubing
Q-Line Water Service Tubing
We B u i l d To u g h P ro d u c t s f o r To u g h E n v i ro n m e n t s
IPEX Pressure Piping Systems Design
Municipal Technical Manual Series
Vol. 1, 4th Edition
2015 by IPEX. All rights reserved. No part of this book may

be used or reproduced in any manner whatsoever without prior
written permission. For information contact: IPEX Management Inc.,
2441 Royal Windsor Drive, Mississauga, Ontario, Canada, L5J 4C7.
The information contained here within is based on current information

and product design at the time of publication and is subject to
change without notification. IPEX does not guarantee or warranty the
accuracy, suitability for particular applications, or results to be
obtained therefrom.
ABOUT IPEX
At IPEX, we have been manufacturing non-metallic pipe and fittings since 1951. We formulate our own compounds
and maintain strict quality control during production. Our products are made available for customers thanks to a
network of regional stocking locations throughout North America. We offer a wide variety of systems including
complete lines of piping, fittings, valves and custom-fabricated items.
More importantly, we are committed to meeting our customers needs. As a leader in the plastic piping industry, IPEX
continually develops new products, modernizes manufacturing facilities and acquires innovative process technology.
In addition, our staff take pride in their work, making available to customers their extensive thermoplastic knowledge
and field experience. IPEX personnel are committed to improving the safety, reliability and performance of
thermoplastic materials. We are involved in several standards committees and are members of and/or comply with
the organizations listed on this page.
For specific details about any IPEX product, contact our customer service department (contact information is listed
on the back cover).
CONTENTS
Pressure Piping Systems Design Manual

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Section One: Product Information

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Summary of Pressure Pipe and Fittings Testing . . . . . . . . . . . . . . . . . . . . . . . .3
Blue Brute Piping Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Bionax Piping Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
IPEX Centurion Piping Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
IPEX FusibleTM PVC Pipe for Trenchless Applications . . . . . . . . . . . . . . . . . . .16
TerraBruteCR Restrained Joint Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
CycleTough Piping Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Blue904TM PEX Water Service Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Q-Line Water Service Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Standards for PVC Pressure Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Section Two: Properties of PVC Pressure Pipe and Pressure System Design
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Material Properties of PVC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Design Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Design Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Chemical Permeation and Installation of PVC Pipe in Contaminated Soils . . . . . .40
UV Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Thermal Effects - Pressure Derating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Thermal Effects - Expansion and Contraction . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Design Calculations
Calculating a Pressure/Class Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Calculating Friction Headloss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Calculating Surge Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Calculating Wave Velocity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Air Entrapment in Pipelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Cyclic Design for PVC Pipes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Thrust Restraint in Gasketed Piping Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Assembly, Installation and Testing of PVC Pressure Pipe Systems . . . . . . . . . . . .49
Section Three: Design Examples

#1: Sewage Forcemain AWWA C905 PVC Pipe . . . . . . . . . . . . . . . . . . . . . .51
#2: Sewage Forcemain ASTM F1483 PVCO Bionax Pipe . . . . . . . . . . . . . . .55
#3: Transmission Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Section Four: Appendices

Appendix A: References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Appendix B: Reference Tables and Conversion Charts . . . . . . . . . . . . . . . . .66
Appendix C: Useful Formulas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Appendix D: Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Appendix E: Tables and Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Pressure Piping Systems Design i

NOTES
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
ii Pressure Piping Systems Design

OVERVIEW
IPEX is one of the largest manufacturers of plastic piping systems in North America. IPEX manufactures piping systems for many
different applications, including:
Sewer collection and transmission
Water supply
Electrical and communications systems
Plumbing systems
Industrial piping systems.
This design manual covers the technical aspects of designing pressure pipe systems with PVC pipe. More specifically, municipal
potable water systems, as well as irrigation and sewer force main systems are described.
The manual is organized into three sections:
Section 1 deals with specific products and includes detailed information on applications, dimensions and applicable standards
for each system.
Section 2 deals with general design issues associated with PVC systems such as hydraulics, cyclic design and other topics that
are applicable to all the products described in the manual.
Section 3 consists of design examples that apply the concepts from the first two sections.
This manual is designed for Engineers, Technologists and other municipal infrastructure professionals who require a deeper
understanding of municipal piping systems than can be gleaned from the more general overview literature available from IPEX.
Pressure Piping Systems Design 1

NOTES
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
2 Pressure Piping Systems Design

SECTION 1: PRODUCT INFORMATION
INTRODUCTION
IPEX offers a number of different pressure piping systems that are used for various applications. While they are all plastic
systems, they vary in outside diameter configurations and in available pressure ratings.
PRODUCT INFORMATION
The products offered are:
Blue Brute and IPEX Centurion Piping Systems Cast-iron outside diameter (CIOD) pipe and fittings
Bionax Pipe Cast-iron outside diameter (CIOD)
IPEX FusibleTM Fusible BruteTM (CIOD) and Fusible SeriesTM (IPS) pipes are available in sizes ranging from 100mm (4") to
750mm (30") with larger sizes in development.
TerraBruteCr Pipe CIOD pipe modified for use with trenchless installation methods such as directional drilling or pipe bursting
CycleTough Piping Systems Iron Pipe Size outside diameter (IPSOD) pipe and fittings
Blue904TM PEX Water Service Tubing 3/4" through 2" PEX pipe designed for commercial and residential water service connections.
Q-Line Water Service Tubing 3/4" and 1" composite pipe designed for use as a water service to connect houses to main lines.
SUMMARY OF PRESSURE PIPE AND FITTINGS TESTING

All IPEX pressure pipes and fittings are manufactured to standards from various recognized organizations such as AWWA, CSA,
ASTM and others. As a result, all pressure pipe products undergo a variety of testing and quality procedures.
CIOD Pipe: Blue Brute, IPEX Centurion, Bionax, Fusible Brute and TerraBrute CR Piping Systems
These piping systems are manufactured under various AWWA standards, including AWWA C900 (Blue Brute and TerraBrute CR),
C905 (IPEX Centurion), and C909 (Bionax). Fittings are manufactured under the C900, C905 and C907 standards.
Each length of Blue Brute, IPEX Centurion, Bionax and TerraBrute CR CIOD pipe is hydrostatically tested in order to verify the
pressure capabilities of each pipe as dictated by AWWA C900 and C905. In addition, burst tests are carried out regularly to
verify the integrity of the pipe and joint system. It should be remembered that the hydrostatic test is done using the pipes own
gasket, which means that both the pipe and the joining system are being checked. AWWA standards also require a number of
non-pressure tests.
TerraBrute CR pipe does not strictly comply with AWWA C900/905 standards because of the dimensional change imposed by
the grooving procedure, however it is tested using the same procedures as conventional Blue Brute and IPEX Centurion. The
hydrostatic proof test is carried out on each length of TerraBrute CR to the same pressures and durations as for standard Blue
Brute or IPEX Centurion.
In addition to Standard requirements, Certifications require very stringent testing and QA/QC procedures. For example, joint
assemblies are regularly tested for full vacuum pressure .
The CSA Certification Program also requires impact testing to be carried out at 0C (32F).
In addition to the pressure and impact testing, finished PVC pipe is tested by using acetone immersion tests and heat reversion
tests. Both tests are used to check that the proper degree of fusion has occurred during the extrusion process.
The dimensional characteristics of each pipe and fitting are checked constantly during the extrusion and molding processes,
and samples are taken for detailed dimensional analysis during each extrusion or molding run.
IPSOD Pipe: CycleTough and Fusible Series
Cycletough pipe undergoes testing identical to that of Blue Brute and IPEX Centurion pipe with the exception of the hydrostatic
proof test of each length of pipe. This does not mean that the pipe is of any lesser quality than Blue Brute or IPEX Centurion pipe
it only means that it is manufactured under a different standard (ASTM D2241) that does not require the hydrostatic proof test.
In addition to performance and dimensional checks, National Sanitation Foundation (NSF) requirements mean that all products
are thoroughly tested to ensure they have no effect on potable water.
To summarize There are many standards governing the manufacture and design of IPEX pressure pipes and fittings. IPEX also
has internal testing standards that are often well in excess of published requirements to ensure acceptable performance on the
jobsite.

BLUE BRUTE PIPING SYSTEMS
Blue Brute is one of the most well known names in municipal
water supply, as it has built up an enviable reputation for
PRODUCT INFORMATION
performance and reliability over the years. Blue Brute pipe and
fittings eliminate the threat of corrosion, while providing reliable
long-term service. While Blue Brute pipe is compatible with
iron fittings, IPEX recommends the use of
Blue Brute fittings as they are made to
match the pipe, and eliminate the Achilles
heel of many systems corroding iron
fittings.
It is advisable to specify pipe and fittings
from the same manufacturer in order to
ensure a completely matched system.
Only by specifying Blue Brute fittings can
you ensure that the fittings have the same
long term strength as the pipe itself.
Applications:
Municipal water distribution systems and fire lines.
Irrigation, sewage forcemains, industrial lines.
Gasket Options For Contaminated Soils

Blue Brute pipe and fittings have removable gaskets. This
allows oil resistant (nitrile) gaskets to be easily substituted
when installing piping systems in contaminated soils. Please
refer to Section 2 Chemical Permeation and Resistance for
more information on this topic.
Standards:
Blue Brute Pipe:

AWWA C900, CSA B137.3 certified, FM 1612 approved,
UL 1285 listed, NSF 61 certified, Certified to NQ 36240-250
Blue Brute Fittings:

AWWA C907, CSA B137.2 (100mm 300mm) certified,
AWWA C900, CSA B137.3 (250mm 300mm) certified,
FM 1612 listed, UL 1285 listed
Sizes larger than 8 inches are fabricated and dimensions are available on request.
Short Form Specifications
PRODUCT INFORMATION
General
Blue Brute pipe shall be certified to CSA B137.3 Rigid been cut in the field, the end shall be made square and
Polyvinyl Chloride PVC Pipe for Pressure Applications and beveled to a 15 chamfer. All insertion lines should be re-drawn,
shall conform to AWWA C900 Polyvinyl Chloride (PVC) according to the IPEX Pressure Pipe Installation Guide.
Pressure Pipe, 4" 12" for Water Transmission and
Molded Fittings
Distribution. Blue Brute DR25 pipe shall have a pressure
class/rating of 1120 kPa (165 psi). DR18 pipe shall have a Blue Brute fittings shall conform to AWWA C907 Polyvinyl
pressure class/rating of 1620 kPa (235 psi). DR14 pipe shall Chloride (PVC) Pressure Fittings for Water (4" through 12")
have a pressure class/rating of 2100 kPa (305 psi). and be certified to CSA B137.2 PVC Injection Molded
Gasketed Fittings for Pressure Applications. They shall also
Material
be UL Listed and FM approved.
Blue Brute pipe shall be made from PVC compound
Fabricated Fittings
conforming to ASTM D1784 cell class 12454.
Fabricated fittings shall be made from segments of AWWA
Product
C900 PVC pipe. Segements are bonded together and may be
Pipe shall be suitable for use at maximum hydrostatic working over-wrapped with fibreglass-reinforced polyester. The
pressure equal to the pressure class/rating at 23C (73F). pressure class must match the pipe. The fittings must meet
Laying lengths shall be 6.1 metres (20 feet). Pipe shall have the requirements of CSA B137.3.
cast-iron outside diameters. Each length of pipe must be
Lubricant
proof-tested at two times the pressure class.
Pipe must be assembled with IPEX non-toxic, water soluble
Joining
lubricant listed by the National Sanitation Foundation.
The gasket shall be carefully fitted to the bell groove if not
Color Coding
already factory installed. Both bell and spigot shall be clean
and free of debris before approved lubricant is applied. The Water pipe and fittings shall be color coded blue.
pipe and/or fittings shall be joined by pushing the spigot into
the bell to the depth line marked on the spigot. When pipe has
Dimensions:
Blue Brute pipes and fittings are manufactured with cast-iron iron pipes. This means that no special transition fittings are
outside diameters (CIOD), which means that they are needed with Blue Brute.
compatible with much of the existing infrastructure of older
DR 25 Class 165 DR 18 Class 235 DR 14 Class 305

AWWA pressure class 165 psi AWWA pressure class 235 psi AWWA pressure class 305 psi
CSA pressure rating 1 130 kPa CSA pressure rating 1 620 kPa CSA pressure rating 2 130 kPa
Min. Wall Min. Wall Min. Wall

Size Avg. ID Avg. OD Avg. ID Avg. OD Avg. ID Avg. OD
Thickness Thickness Thickness
in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm
4 100 4.42 112 0.192 4.88 4.80 122 4.27 108 0.267 6.78 4.80 122 4.11 104 0.343 8.71 4.80 122
6 150 6.35 161 0.276 7.01 6.90 175 6.13 155 0.383 9.73 6.90 175 5.91 149 0.493 12.52 6.90 175
8 200 8.33 212 0.362 9.20 9.05 230 8.05 204 0.502 12.80 9.05 230 7.76 198 0.646 16.42 9.05 230
10 250 10.21 260 0.444 11.30 11.10 282 9.87 250 0.616 15.70 11.10 282 9.51 242 0.793 20.14 11.10 282
12 300 12.15 309 0.527 13.41 13.20 335 11.73 297 0.733 18.62 13.20 335 11.31 287 0.943 23.95 13.20 335

Bell OD for Joint Restraint Selection

Size Minimum Maximum
PRODUCT INFORMATION
in mm in mm in mm
OD
4 100 5.44 138 5.61 142
6 150 7.84 199 8.03 204
8 200 10.29 261 10.55 268
10 250 12.63 322 12.96 329
12 300 15.07 383 15.46 393
14 350 17.28 439 17.73 450
16 400 19.64 448 20.17 512
L1 90 Elbow
Size L1
in mm in mm
L1 4 100 2.6 67
6 150 4.3 108
8 200 5.5 140
45 Elbow
L1 Size L1
in mm in mm
4 100 1.3 33
L1 6 150 1.8 46
8 200 2.2 56
10 250 2.7 70
12 300 3.2 82
22-1/2 Elbow
Size L1
L1
in mm in mm
L1 6 150 1.0 25
8 200 1.1 28
10 250 1.7 43
12 300 1.9 48
11-1/4 Elbow
Size L1
L1
in mm in mm
L1
4 100 3.0 75
6 150 0.8 20
8 200 0.9 23
Note: Other DRs and sizes up to 48" (1200mm) are available on request.
Tee
PRODUCT INFORMATION
Size L1 L2
L1
in mm in mm in mm
4x4x4 100 x 100 x 100 2.6 67 2.6 67
6x6x4 150 x 150 x 100 4.0 102 3.3 87
6x6x6 150 x 150 x 150 4.3 108 4.3 108
8x8x4 200 x 200 x 100 5.1 130 3.6 91
L2
8x8x6 200 x 200 x 150 5.3 136 4.7 120
8x8x8 200 x 200 x 200 5.6 143 5.8 148
10 x 10 x 4 250 x 250 x 100 6.7 171 6.7 171
L1
10 x 10 x 6 250 x 250 x 150 6.7 171 6.7 171
10 x 10 x 8 250 x 250 x 200 6.7 171 6.7 171
10 x 10 x 10 250 x 250 x 250 6.7 171 6.7 171
12 x 12 x 4 300 x 300 x 100 7.7 195 7.7 195
12 x 12 x 6 300 x 300 x 150 7.7 195 7.7 195
12 x 12 x 8 300 x 300 x 200 7.7 195 7.7 195
12 x 12 x 10 300 x 300 x 250 7.7 195 7.7 195
L1
12 x 12 x 12 300 x 300 x 300 7.7 195 7.7 195
Hydrant Tee
Size L1 L2
in mm in mm in mm
L2
10 x 10 x 6 250 x 250 x 150 7.0 178 6.7 171
12 x 12 x 6 300 x 300 x 150 8.1 206 7.7 195
L1
Reducing Adapter Spigot x Bell
Size L1 L2
L1
in mm in mm in mm
6x4 150 x 100 5.6 141 4.3 108
8x6 200 x 150 6.5 165 5.7 145
10 x 8 250 x 200 7.0 178 5.8 147
L2 12 x 10 300 x 250 7.9 202 6.6 167
Coupling
(available w/o center stop as a Repair Coupling)
Size L1
in mm in mm
L1
4 100 0.2 5
6 150 0.3 8
8 200 0.3 7
10* 250 0.5 13
12* 300 0.5 13
* One-piece machined coupling.
Note: 3/4" (20mm) Taps to 2" (50mm). Taps: AWWA Thread

Single Tapped Coupling

PRODUCT INFORMATION
Size A L1
in mm in mm in mm
4 x 4 x 3/4 100 x 100 x 20 3/4 20 2.0 50
4x4x1 100 x 100 x 25 1 25 2.0 50
6 x 6 x 3/4 150 x 150 x 20 3/4 20 3.0 76
A L 6x6x1 150 x 150 x 25 1 25 3.0 76

6 x 6 x 1-1/4 150 x 150 x 32 1-1/4 32 3.0 76
6 x 6 x 1-1/2 150 x 150 x 40 1-1/2 40 3.0 76
8 x 8 x 3/4 200 x 200 x 20 3/4 20 3.0 76
8x8x1 200 x 200 x 25 1 25 3.0 76
8 x 8 x 1-1/4 200 x 200 x 32 1-1/4 32 3.0 76
8 x 8 x 1-1/2 200 x 200 x 40 1-1/2 40 3.0 76
8x8x2 200 x 200 x 50 2 50 3.0 76
10 x 10 x 3/4* 250 x 250 x 20 3/4 20 3.0 76
10 x 10 x 1* 250 x 250 x 25 1 25 3.0 76
12 x 12 x 3/4* 300 x 300 x 20 3/4 20 3.0 76
12 x 12 x 1* 300 x 300 x 25 1 25 3.0 76
* One-piece machined coupling.
Double Tapped Coupling

Size A B L
in mm in mm in mm in mm
6 x 3/4 x 3/4 150 x 20 x 20 3/4 20 3/4 20 3.0 76
6 x 1 x 3/4 150 x 25 x 20 3/4 20 1 25 3.0 76
6x1x1 150 x 25 x 25 1 25 1 25 3.0 76
6 x 1-1/4 x 3/4 150 x 32 x 20 3/4 20 1-1/4 32 3.0 76
A B L
6 x 1-1/4 x 1 150 x 32 x 25 1 25 1-1/4 32 3.0 76
6 x 1-1/2 x 3/4 150 x 40 x 20 3/4 20 1-1/2 40 3.0 76
6 x 1-1/2 x 1 150 x 40 x 25 1 25 1-1/2 40 3.0 76
6 x 2 x 3/4 150 x 50 x 20 3/4 20 2 50 3.0 76
6x2x1 150 x 50 x 25 1 25 2 50 3.0 76
8 x 3/4 x 3/4 200 x 20 x 20 3/4 20 3/4 20 3.0 76
8 x 1 x 3/4 200 x 25 x 20 3/4 20 1 25 3.0 76
8x1x1 200 x 25 x 25 1 25 1 25 3.0 76
8 x 1-1/4 x 3/4 200 x 32 x 20 3/4 20 1-1/4 32 3.0 76
8 x 1-1/4 x 1 200 x 32 x 25 1 25 1-1/4 32 3.0 76
8 x 1-1/2 x 3/4 200 x 40 x 20 3/4 20 1-1/2 40 3.0 76
8 x 1-1/2 x 1 200 x 40 x 25 1 25 1-1/2 40 3.0 76
8 x 2 x 3/4 200 x 50 x 20 3/4 20 2 50 3.0 76
8x2x1 200 x 50 x 25 1 25 2 50 3.0 76
High Deflection Coupling
PRODUCT INFORMATION
Size L1
D E
in mm in mm
10 250 3.5 89
12 300 3.5 89
Plug
Size L1
in mm in mm
4 100 6.5 164
6 150 7.8 198
L1 8 200 9.1 231
10 250 10.2 258
12 300 9.8 249
Tapped Plug (IPS Threads)

Size L1
in mm in mm
Thread
4 x 3/4 100 x 20 6.5 164
4x1 100 x 25 6.5 164
4 x 1-1/2 100 x 40 6.5 164
L1 4x2 100 x 50 6.5 164
6 x 3/4 150 x 20 7.8 198
6x1 150 x 25 7.8 198
6 x 1-1/2 150 x 40 7.8 198
6x2 150 x 50 7.8 198
8 x 3/4 200 x 20 9.1 231
8x1 200 x 25 9.1 231
8 x 1-1/2 200 x 40 9.1 231
8x2 200 x 50 9.1 231

BIONAX PIPING SYSTEMS
Bionax PVCO pipe and Blue Brute PVC fittings eliminate

corrosion and provide a reliable long-term piping system.
PRODUCT INFORMATION
Although Bionax is compatible with iron fittings, IPEX

recommends the use of Blue Brute fittings since they result in
an all-plastic system that prevents corroding
iron fittings.
It is advisable to specify pipe and fittings from
the same manufacturer to ensure a
completely matched system. If Bionax pipe is
specified with Blue Brute fittings, the pipe
and fittings will provide matched pressure
capacities.
Applications:
Municipal water distribution systems
Sewage forcemains, industrial process piping
Pressure Class/Rating
Bionax CIOD pipe has a Pressure Rating (CSA) or a Pressure
Class (AWWA) of 165 psi or 235 psi. It also has a Pressure Class
of 150 psi for FM and a Pressure Rating of 200 psi by ASTM.
Surge Pressure
Surge pressures generated in Bionax pipe are lower than for any
other municipal pipe.
The short-term rating of Bionax CIOD pipe is 376 psi (for
occasional surge-pressure applications).
Standards
Bionax pipe:
ANSI/NSF Standard 14, ANSI/NSF Standard 61
ASTM D1784, D3139, F477 and F1483
NSF-certified to AWWA C909-09 and ASTM F1483-05,
CSA-certified to B137.3.1 and FM-certified to FM1612.
NQ3660-950

BIONAX PIPING SYSTEMS
PRODUCT INFORMATION
General
Fittings
Bionax CIOD pipe shall be certified to AWWA C909
Molecularly Oriented Polyvinyl Chloride (PVCO) Pressure Pipe Bionax piping systems shall include IPEX Blue Brute molded
(4" 24") for Water, Wastewater, and Reclaimed Water and fabricated fittings.
Service and certified to CSA B137.3.1 MOLECULARLY Lubricant
ORIENTED POLYVINYLCHLORIDE (PVCO) PIPE FOR
PRESSURE APPLICATIONS. Bionax shall have a pressure Pipe must be assembled with IPEX water-soluble lubricant
class (AWWA) or pressure rating (CSA) of 165 psi or 235 psi. listed to NSF Standard 61.
Material Color Coding
PVCO pipe shall be manufactured from rigid polyvinyl chloride CIOD pipe shall be color coded blue.
(PVC) compound meeting the requirements of ASTM D1784 Joining
cell class 12454.
The gasket shall be carefully fitted to the bell groove if not
Gaskets shall meet ASTM F477 for high-head applications. already factory-installed. Both bell and spigot shall be clean
Product and free of debris before lubricant is applied. The pipe shall be
joined by push-fitting bell and spigot joint to the depth line
Finished PVCO pipe shall have an HDB of 7100 psi. Laying marked on the spigot. When pipe has been cut in the field, the
lengths shall be 6.1 meters (20 feet). Pipe shall have cast-iron end shall be made square and bevelled to a
outside diameters. Every length must be proof-tested at two 10-degree chamfer and the insertion line shall be redrawn per
times the pressure class. IPEXs Pressure Pipe Installation Guide.
Dimensions
Pressure Class/Rating 235 psi @ 73F (1 620 kPa @ 23C)
Size
Average OD Min Wall Thickness Average ID
4 100 4.80 122 0.154 3.91 4.48 114
6 150 6.90 175 0.221 5.62 6.44 163
8 200 9.05 230 0.290 7.36 8.44 214
10 250 11.10 282 0.356 9.03 10.35 263
12 300 13.20 335 0.423 10.74 12.31 313
14 350 15.30 389 0.494 12.54 14.33 364
16 400 17.50 442 0.557 14.16 16.30 414
18 450 19.50 495 0.625 15.88 18.23 463
Pressure Class/Rating 165 psi @ 73F (1 150 kPa @ 23C)

Size
Average OD Min Wall Thickness Average ID
14 350 15.30 389 0.347 8.83 14.57 370
16 400 17.50 442 0.395 10.04 16.57 421
18 450 19.50 495 0.443 11.25 18.54 471

IPEX CENTURION PIPING SYSTEMS
IPEX Centurion extends the benefits of Blue Brute to

larger diameters of pipe and new applications. The
PRODUCT INFORMATION
versatility and ease of installation of IPEX Centurion

is unmatched and costly and difficult
to install corrosion protection is
eliminated. In addition, unlike HDPE or
concrete pressure pipe, every length
of IPEX Centurion is tested to double
its pressure rating.
Applications:
Water transmission lines, forcemains.
Irrigation, gravity lines, industrial lines
Standards:
AWWA C905, CSA B137.3, NQ 3624-250, NSF 61
Factory Mutual FM 1612:
DR18 is FM approved to 20" (500mm diameter)
Underwriters Laboratories UL 1285:
DR18 is listed to 24" (600mm diameter)
DR25 is listed to 30" (750mm diameter)


General
PRODUCT INFORMATION
Fabricated Fittings
Pipe must conform to AWWA C905 and be certified to CSA
B137.3 RIGID POLYVINYL CHLORIDE (PVC) PIPE FOR Fabricated fittings shall be made from segments of AWWA
PRESSURE APPLICATIONS. DR51, 41, 32.5, 25, 18, and 14 C905 pipe that are butt-fused or bonded together. Some
pipe must have the following pressure/class ratings: 80 psi fittings are over-wrapped with fiberglass-reinforced polyester.
(550 kPa), 100 psi (690 kPa), 125 psi (860 kPa), 165 psi (1 The fittings must always meet the pressure/class rating of the
140 kPa), 235 psi (1 620 kPa) and 305 psi (2 100 kPa). For pipe system.
pressure applications, each length of pipe must be hydro-
tested at twice the rating and a short-term pressure test must
be conducted once per production run. Pipe to be IPEX
Centurion or approved equal.
Pressure Ratings Surge Pressures

IPEX Centurion can withstand extremely high short term Transient pressures in pipelines occur as a result of the fluid
pressures, in addition to lower levels of long-term pressure. As velocity changing over a relatively short time. The method for
a result, AWWA C905 standard includes both long term approximating a surge pressure is described in section 2.
pressure ratings (LTR) and short term ratings (STR). However it should be noted that for most large diameter
pipelines, a formal transient analysis should be carried out by a
qualified person in order to fully understand the effects of
Short Term Rating Long Term Rating transients in any given system. The method shown in section
DR 2 is certainly appropriate for initial design purposes however.
psi kPa psi kPa
The table below shows the surge pressure generated
51 125 880 80 550 assuming an instantaneous stoppage of a flow moving at 0.3
m/s (1 ft/s).
41 160 100 100 690
32.5 200 1 380 125 860 Surge Pressure

DR
25 264 1 820 165 1 140 psi kPa
18 376 2 590 235 1 620 51 10.8 75
14 488 3 370 305 2 100 41 11.4 79

32.5 12.8 88
25 14.7 101
18 17.4 120
14 19.8 137
Bionax (PC235) 14.1 97

IPEX Centurion for Gravity Applications

PRODUCT INFORMATION
With its pressure rated joints and non-corroding construction, IPEX Centurion is a natural choice for gravity flow lines. When
designing any flexible conduit application, the ring deflection should be calculated for the applicable loading conditions. The table
below shows the ring deflections for a variety of different DRs based on depth of bury and H20 loading. For more information on
how to calculate ring deflections for PVC pipe, please refer to the IPEX Sewer Design Manual.
1. Deflection values shown include effect of H20 live load and 5. DR18 & DR 14 deflections have not been shown because
dead load. they are insignificant in most cases.
2. External loading based upon a prism load of soil weight of 6. Recommended maximum deflection is 7.5%.
120 lbs. per cubic foot (1 900 kg/m3). Contact IPEX for applications where greater deflections are
3. Bedding classifications correspond to ASTM D2321. anticipated.
4. The deflection lag factor is 1.0 for a prism load. 7. n/r - not recommended for H20 live load (ok with dead load)
Table 1 Percent (%) Deflection for IPEX Centurion Pressure Pipe
DEPTH OF COVER
ASTM EMBEDMENT DENSITY
E' psi
MATERIAL (PROCTOR) DR ft 1 2 4 6 8 10 15 20 25 30 35 40 45 50
(kPa)
CLASSIFICATION AASHO T-99
m 0.3 0.6 1.2 1.8 2.4 3.0 4.6 6.1 7.6 9.1 10.7 12.2 13.7 15.2
51 n/r 0.5 0.3 0.4 0.4 0.5 0.7 0.9 1.1 1.4 1.6 1.8 2.0 2.3
Manufactured 41 n/r 0.5 0.3 0.4 0.4 0.4 0.7 0.9 1.1 1.3 1.6 1.8 2.0 2.2
3,000
Granular CLASS I 90%
(20 700) 32.5 0.7 0.5 0.3 0.3 0.4 0.4 0.7 0.9 1.1 1.3 1.5 1.7 2.0 2.2
Angular
25 0.7 0.5 0.3 0.3 0.4 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.9 2.1
51 n/r 0.7 0.5 0.5 0.6 0.7 1.0 1.3 1.7 2.0 2.3 2.7 3.0 3.4
2,000 41 n/r 0.7 0.5 0.5 0.6 0.7 1.0 1.3 1.7 2.0 2.3 2.6 3.0 3.3
90%
(13 000) 32.5 1.0 0.7 0.5 0.5 0.5 0.6 1.0 1.3 1.6 1.9 2.2 2.6 2.9 3.2
Clean Sand & 25 1.0 0.7 0.4 0.5 0.5 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 2.9
CLASS II
Gravel 51 n/r 1.5 1.0 1.1 1.1 1.3 2.0 2.6 3.3 4.0 4.6 5.3 5.9 6.6
1,000 41 n/r 1.4 1.0 1.0 1.1 1.3 1.9 2.6 3.2 3.8 4.5 5.1 5.8 6.4
80%
(7 000) 32.5 2.0 1.3 0.9 1.0 1.0 1.2 1.8 2.4 3.0 3.6 4.2 4.8 5.4 6.0
25 1.7 1.1 0.8 0.8 0.9 1.0 1.6 2.1 2.6 3.1 3.6 4.2 4.7 5.2
51 n/r 1.5 1.0 1.1 1.1 1.3 2.0 2.6 3.3 4.0 4.6 5.3 5.9 6.6
1,000 41 n/r 1.4 1.0 1.0 1.1 1.3 1.9 2.6 3.2 3.8 4.5 5.1 5.8 6.4
90%
(7 000) 32.5 2.0 1.3 0.9 1.0 1.0 1.2 1.8 2.4 3.0 3.6 4.2 4.8 5.4 6.0
Sand & Gravel 25 1.7 1.1 0.8 0.8 0.9 1.0 1.6 2.1 2.6 3.1 3.6 4.2 4.7 5.2
CLASS III
with Fines 51 n/r n/r 1.9 2.0 2.2 2.6 3.8 5.1 6.4 7.7 8.9 10.2 11.5 12.8
500 41 n/r n/r 1.8 1.9 2.1 2.4 3.6 4.8 6.0 7.2 8.4 9.6 10.8 12.0
85%
(3 500) 32.5 n/r 2.4 1.6 1.7 1.8 2.1 3.2 4.3 5.3 6.4 7.5 8.5 9.6 10.7
25 n/r 1.9 1.3 1.3 1.4 1.7 2.5 3.3 4.2 5.0 5.9 6.7 7.5 8.4
51 n/r n/r 2.4 2.5 2.7 3.1 4.7 6.3 7.9 9.4 11.0 12.6 14.1 15.7
400 41 n/r n/r 2.2 2.3 2.5 2.9 4.4 5.8 7.3 8.8 10.2 11.7 13.1 14.6
Silt & Clay CLASS IV 85%
(2 760) 32.5 n/r 2.8 1.9 2.0 2.2 2.5 3.8 5.1 6.3 7.6 8.9 10.1 11.4 12.7
25 n/r 2.1 1.4 1.5 1.6 1.9 2.9 3.8 4.8 5.7 6.7 7.6 8.6 9.5

Dimensions
PRODUCT INFORMATION
IPEX Centurion is manufactured with a cast-iron outside IPEX Centurion Fittings are manufactured using sections of
diameter (CIOD) so it is compatible with much of the existing AWWA C905 pipe that are fused or bonded together. Some
older infrastructure of iron pipes. In addition, IPEX Centurion fittings are overwrapped with a layer of fibre reinforced plastic
can be field-cut, which means unexpected changes in the field (FRP). While IPEX Centurion is compatible with iron fittings,
can be accommodated quickly, without having to wait for new IPEX recommends the use of IPEX Centurion fittings
shop drawings. exclusively with IPEX Centurion pipe.
PR/PC 80 (SDR51) PR/PC 100 (SDR41) PR/PC 125 (SDR32.5)

14 350 - - - - - - 14.6 369.7 0.37 9.5 15.3 388.6 - - - - - -
16 400 - - - - - - 16.6 420.4 0.43 10.8 17.4 442.0 - - - - - -
18 450 18.7 475.9 0.38 9.71 19.5 495.3 18.5 471.1 0.48 12.1 19.5 495.3 - - - - - -
20 500 20.8 527.0 0.42 10.80 21.6 548.6 20.5 521.8 0.53 13.4 21.6 548.6 - - - - - -
24 600 24.8 629.6 0.50 12.90 25.8 655.3 24.5 623.3 0.63 16.0 25.8 655.3 24.2 615.0 0.80 20.2 25.8 655.3
30 750 30.7 780.9 0.63 15.93 32.0 812.8 30.4 773.2 0.78 19.8 32.0 812.8 30.0 762.8 0.98 25.0 32.0 812.8
36 900 36.8 934.7 0.75 19.10 38.3 972.8 36.4 925.3 0.93 23.7 38.3 972.8 35.9 912.9 1.18 29.9 38.3 972.8
42 1050 42.6 1082.8 0.87 22.20 44.5 1130.3 42.2 1071.4 1.09 27.5 44.5 1130.3 41.6 1056.6 1.37 34.8 44.5 1130.3
48 1200 48.7 1236.2 1.00 25.30 50.8 1290.3 48.2 1223.0 1.24 31.5 50.8 1290.3 - - - - - -
PR/PC 165 (DR25) PR/PC 235 (DR18) PR/PC 305 (DR14)

14 350 14.1 357.5 0.61 15.60 15.3 388.6 13.6 345.4 0.85 21.6 15.3 388.6 13.1 333.0 1.09 27.8 15.3 388.6
16 400 16.0 406.6 0.70 17.70 17.4 442.0 15.5 392.9 0.97 24.6 17.4 442.0 14.9 378.8 1.24 31.6 17.4 442.0
18 450 17.9 455.7 0.78 19.81 19.5 495.3 17.3 440.3 1.08 27.5 19.5 495.3 - - - - - -
20 500 19.9 504.7 0.86 22.00 21.6 548.6 19.2 487.6 1.20 30.5 21.6 548.6 - - - - - -
24 600 23.7 602.9 1.03 26.21 25.8 655.3 22.9 582.5 1.43 36.4 25.8 655.3 - - - - - -
30 750 29.4 747.8 1.28 32.51 32.0 812.8 - - - - - - - - - - - -
36 900 35.2 895.0 1.53 38.91 38.3 972.8 - - - - - - - - - - - -
42 1050 - - - - - - - - - - - - - - - - - -
48 1200 - - - - - - - - - - - - - - - - -

IPEX FUSIBLETM PVC PIPE FOR TRENCHLESS APPLICATIONS
By combining the mechanical properties of PVC

with an innovative, patented butt fusion process,
PRODUCT INFORMATION
IPEX provides the only available method of installing

a continuous, monolithic, fully restrained PVC pipe
system. Capable of being used in a
variety of trenchless or conventional
direct bury applications, Fusible PVCTM
pipe systems have been installed at
numerous sites throughout the United
States, Canada and Mexico for both
pressure and non-pressure
installations in the water and sewer
industries.
Fusible Brute (CIOD) and Fusible

Series (IPS) pipes are available in sizes
ranging from 100mm (4") to 750mm
(30") with larger sizes in development.
The proprietary PVC formulation,
fusion process as well as our licensing
and training program allow for the consistent,
reliable fusion of Fusible Brute and Fusible Series
pipes to create piping systems of unparalleled
strength.
Applications:
Water mains, sanitary sewers, process and raw water,
reclaimed water and storm drains.
Installations:
Slip Lining
Pipe Bursting
Direct Bury
Horizontal Directional Drilling
Standards:
AWWA C900 & C905, CSA B137.3, NSF 61 and ASTM cell
classification 12454.
Pipe used in IPEX Fusible BruteTM and Fusible SeriesTM product
lines Certified to CSA B137.3.
IPEX Fusible BruteTM products meet the AWWA C900 and
C905 standards.
IPEX Fusible BruteTM and Fusible SeriesTM products are marked
with NSF 61 when used for potable service.

PRODUCT INFORMATION
Fusible PVC Pipe Fusion Technician Requirements
IPEX pipe used in Fusible applications is certified to CSA The PVC Fusion contractor must be identified in the tender
B137.3 and NSF61, and conforms to AWWA C900 or AWWA documents and the Fusion Technician shall be fully qualified by
C905. Testing shall be in accordance with CSA B137.3 and IPEX to fuse Fusible PVC pipe of the type(s) and size(s) being
AWWA standards for all pipe types. used. Qualification shall be current as of the actual date of the
tender and of fusion on the project.
Minimum Bend Radius Effect of Temperature

Minimum bend radii are independent of DR.
Bend Radius calculations are based on the assumption that a Tensile Modulus of
Pressure
fitting or flange is present/to be installed in the bend. The Temperature Factor (Pull Elasticity Factor
Rating Factor
Bend Radius for PVC includes a safety factor of 2.5 [Unibell Force) (Bend Radius)
Handbook of PVC, 4th Edition, Equation 8.6].
F C % % %
Pipe Size Bend Radius 73.4 23 100 100 100
inches mm ft m 80 26.7 88 95 98
4 100 328.08 30.5 90 32.2 75 87 94
6 150 492.12 43.7 100 37.8 62 78 88
8 200 656.17 57.5 120 48.9 40 63 78
10 250 820.21 70.4 140 60 22 58 70

12 300 984.25 83.7
14 350 1148.29 97.1
16 400 1312.33 110.4
Critical Buckling Pressure & Grout Pressure

Initiates deformation of pipe through external pressure
Important to backfilling and grouting
Maximum recommended pressure:
Critical Buckling Pressures are calculated using a Long Term
Critical Buckling Pressure Grout Pressure
DR Modulus of Elasticity (400,000 PSI for PVC), and published
psi psi Poisson's Ratio [Unibell Handbook of PVC, 4th Edition,
equation 7.13]. No safety factor is included in the calculation
14 426 213 for Critical Buckling Pressures.
18 190 85 Note: These maximum pressures are based on the
temperature in the wall of the pipe not exceeding 73F (23C)
25 67 33.5
Maximum grouting pressures must be reduced with increased
32.5 27 13.5
wall temperatures.
41 14.6 7.3
See the IPEX pressure pipe installation guide for more details.
51 7.4 3.7

IPEX Fusible Brute Pipe Data CIOD

PRODUCT INFORMATION
Safe Pulling Pressure Critical Buckling Min. Allowable

Nominal Size Avg. O.D. Min. Wall Avg. I.D.
DR Force Rating Pressure Bend Radius
(in) (mm) (mm) (mm) (mm) (lbf) (psi) (psi) (m)

4 100 DR 14 122.00 8.71 104.00 13,877 305 426 30.5
6 150 DR 14 175.00 12.52 149.00 28,736 305 426 43.7
8 200 DR 14 230.00 16.42 198.00 46,720 305 426 57.5
10 250 DR 14 282.00 20.14 242.00 71,499 305 426 70.4
12 300 DR 14 335.00 23.95 287.00 101,846 305 426 83.7
4 100 DR 18 122.00 6.78 108.00 10,984 235 190 30.5
6 150 DR 18 175.00 9.73 155.00 22,514 235 190 43.7
8 200 DR 18 230.00 12.80 204.00 38,492 235 190 57.5
10 250 DR 18 282.00 15.70 250.00 58,073 235 190 70.4
12 300 DR 18 335.00 18.62 297.00 81,924 235 190 83.7
14 350 DR 18 388.60 21.60 345.40 108,166 235 190 97.1
16 400 DR 18 442.00 24.60 392.90 139,838 235 190 110.4
18 450 DR 18 495.30 27.50 440.30 175,535 235 190 123.7
20 500 DR 18 548.60 30.50 487.60 215,617 235 190 137.1
24 600 DR 18 655.30 36.40 582.50 307,392 235 190 163.7
4 100 DR 25 122.00 4.88 112.00 7,982 165 67 30.5
6 150 DR 25 175.00 7.01 161.00 15,518 165 67 43.7
8 200 DR 25 230.00 9.20 212.00 26,616 165 67 57.5
10 250 DR 25 282.00 11.30 260.00 40,438 165 67 70.4
12 300 DR 25 335.00 13.41 309.00 57,247 165 67 83.7
14 350 DR 25 388.60 15.60 357.50 77,491 165 67 97.1
16 400 DR 25 442.00 17.70 406.60 99,719 165 67 110.4
18 450 DR 25 495.30 19.81 455.70 125,284 165 67 123.7
20 500 DR 25 548.60 22.00 504.70 153,768 165 67 137.1
24 600 DR 25 655.30 26.21 602.90 218,545 165 67 163.7
30 750 DR 25 812.80 32.51 747.80 335,507 165 67 203.1
36 900 DR 25 972.80 38.91 895.00 480,557 165 67 243.0
20 500 DR 32.5 548.60 16.90 512.83 118,256 125 30 137.1
24 600 DR 32.5 655.30 20.20 615.00 168,551 125 30 163.7

IPEX Fusible Series Pipe Data IPS
PRODUCT INFORMATION
Nominal Safe Pulling Pressure Critical Buckling Min. Allowable
Avg. O.D. Min. Wall Avg. I.D.
Size DR Force Rating Pressure Bend Radius
(in) (mm) (mm) (mm) (mm) (lbf) (psi) (psi) (m)
4 100 DR 21 114.30 5.44 102.77 7,783 200 117 28.6

6 150 DR 21 168.30 8.02 151.30 16,931 200 117 42.0
8 200 DR 21 219.10 10.40 197.00 28,612 200 117 54.7
10 250 DR 21 273.10 13.00 245.49 44,887 200 117 68.2
12 300 DR 21 323.90 15.40 291.25 63,280 200 117 80.9
14 350 DR 21 355.60 16.90 319.77 76,343 200 117 88.8
16 400 DR 21 406.40 19.40 365.27 99,895 200 117 101.5
18 450 DR 21 457.20 21.80 410.98 126,646 200 117 114.2
20 500 DR 21 508.00 24.20 456.70 155,897 200 117 126.9
24 600 DR 21 609.60 29.00 548.12 223,407 200 117 152.3
4 100 DR 26 114.30 4.37 105.01 6,255 160 60 28.6
6 150 DR 26 168.30 6.48 154.56 13,694 160 60 42.0
8 200 DR 26 219.10 8.41 201.20 23,166 160 60 54.7
10 250 DR 26 273.10 10.50 250.79 36,328 160 60 68.2
12 300 DR 26 323.90 12.40 297.61 51,146 160 60 80.9
14 350 DR 26 355.60 13.70 326.56 62,091 160 60 88.8
16 400 DR 26 406.40 15.60 373.33 80,612 160 60 101.5
18 450 DR 26 457.20 17.60 419.89 102,675 160 60 114.2
20 500 DR 26 508.00 19.60 466.45 126,725 160 60 126.9
24 600 DR 26 609.60 23.50 559.78 181,538 160 60 152.3
Notes:
PVC safe pull stress of 7,000 psi is based on the published value of 7,000-8,000 PSI for short term tensile
1
strength and a safety factor of 2.5 [Unibell Handbook of PVC, 4th Edition].
2 PVC safe pull forces are based on minimum wall thickness and the safe pull stresses as calculated per Note 1.
Critical Buckling Pressures are calculated using a Long Term Modulus of Elasticity (400,000 PSI for PVC), and
3 published Poisson's Ratio [Unibell Handbook of PVC, 4th Edition, equation 7.13]. No safety factor is included in
the calculation for Critical Buckling Pressures.
4 Pressure Ratings are per AWWA C900, AWWA C905 at 73 F.
Bend Radius calculations are based on the assumption that a fitting or flange is present/to be installed in the
5 bend. The Bend Radius for PVC includes a safety factor of 2.5 [Unibell Handbook of PVC, 4th Edition, Equation
8.6].

TERRABRUTE CR RESTRAINED JOINT PIPE
TerraBrute CR is a modified AWWA C900 pipe that has been
specifically designed for use with trenchless installation
PRODUCT INFORMATION
techniques like horizontal directional drilling (HDD) and pipe

bursting. Using an innovative system of rings and pins,
TerraBrute CR can withstand higher pull forces than any other
mechanically restrained plastic piping system, while
simultaneously being able to bend and flex in a
borehole.
In addition to trenchless installations, TerraBrute
CR's versatile joint is perfect for above ground
installations like bridge crossings where there may
be significant temperature extremes. Where other
piping systems require costly and maintenance
intensive expansion joints, the wide groove in each
TerraBrute CR joint allows expansion and
contraction of each pipe.
Another key attribute of the TerraBrute CR joint is
that it allows pipe rotation without damage. This
can be an issue in seismic zones where piping
systems are subjected to a wide variety of soil
induced stresses during earthquake events.
External Pressures
Drilling fluids are used under many different soil conditions both
to keep the borehole open and to remove the spoil from drilling
and reaming operations. This drilling fluid is pressurized, and as
a result, it is important that a pipe joint be able to withstand
these external pressures without leaking fluid into the pipe
string. IPEX has tested fully deflected joints to well over 100 psi
external pressure with zero leakage.
Applications:
HDD, pipe bursting, bridge crossings, seismic zones,
casing installations and steep slopes.
Standards
AWWA C900
TerraBrute CR is made with pipe conforming to AWWA C900.
However once the pipe is grooved on the spigot end its
dimensions do not match those published in the C900
standard. Because of this small dimensional difference the
pipe, once grooved, does not strictly conform to the C900
standard. It is important to note however, that TerraBrute CR
is subjected to the same testing program as IPEXs Blue Brute
(C900) pipe.
CSA B137.3
TerraBrute CR is certified to CSA B137.3.
NQ 3624-250
Factory Mutual and Underwriters Laboratories
TerraBrute CR is made from starting stock that is Factory
Mutual approved, and ULC and ULI listed.

PRODUCT INFORMATION
PVC pipe used for horizontal directional drilling (HDD) or
other trenchless installation methods shall be manufactured
with a cast iron outside diameter (CIOD) and shall be made Nominal Size Maximum Allowable Pulling Force
with starting stock certified to CSA B137.3 for 100mm -
300mm (4" - 12") diameters. Pipe will meet the requirements mm Inches kN Lbs.
of AWWA C900, must be Factory Mutual approved, and listed
by ULC or UL. 100 4 50 11200
150 6 110 24700
The maximum allowable pulling force shall be the ultimate
tensile capacity of the piping system divided by a safety factor 200 8 115 25800
of 2, as shown in the adjacent table. 250 10 187 42100
PVC pipe must be manufactured with an integral bell, and 300 12 275 61800
must have removable gaskets to allow the use of oil-resistant
(nitrile) gaskets in contaminated soils.
Dimensions TerraBrute CR Pipe Stops

TerraBrute CR is virtually identical to Blue Brute dimensionally. IPEX TerraBrute CR Pipe Stops have been specifically
It has a slightly shorter laying length, as a result of the designed to simplify the installation of 8", 10", and 12"
extended bell, as well as a groove cut into the spigot end of (200mm, 250mm, and 300mm) TerraBrute CR. Due to fairly
the pipe. large insertion forces, it can often be difficult to align the
internal groove with the pin holes on the larger diameter
One key dimension that must be remembered when planning
TerraBrute CR; the new TerraBrute CR Pipe Stops will virtually
pre-ream operations is the absolute maximum outside
eliminate this problem of over-homing the pipe. TerraBrute CR
diameter of the pipe. The table below shows the maximum
Pipe Stops will reduce stoppages in the installation process to
outside diameter of each size.
pull back and reposition the pipe.
Maximum Outside Diameter IPEX TerraBrute CR Pipe
Nominal Size
(Outside Ring) Stops can be placed on
the pipe quickly and
mm Inches mm Inches
easily; a pair of vice-
100 4 160 6.3 grips is all that is needed
to secure the Pipe Stop
150 6 230 9.1 in place. Made from
high-strength steel,
200 8 290 11.4 TerraBrute CR Pipe
250 10 350 14.2 Stops are designed to
withstand repeated use
300 12 415 16.3 for all of your
installations.
Due to the extended bell configuration, TerraBrute CR has Easy to Use
slightly shorter laying length than standard Blue Brute pipe:
TerraBrute CR Pipe Stops are simple and easy to use, offering
quick assembly and disassembly to help prevent installation
Nominal Size Laying Lengths delays. A pair of vice grips is all that is needed to secure the
Pipe Stop in place.
mm Inches m Feet/Inches
Strong and Tough
100 4 6.04 19' 10" Made from steel, TerraBrute CR Pipe Stops are built strong,
tough and are durable enough to withstand repeated use on
150 6 6.03 19' 9"
every job.
200 8 6.01 19' 9"
Prevent Over-homing
250 10 6.01 19' 9" TerraBrute CR Pipe Stops virtually eliminate the risk of over-
300 12 6.01 19' 9" homing the pipe. There is no need to pull back and reposition
the pipe as the groove will always end up properly aligned with
the pin holes.

Pulling Forces Bending Forces

PRODUCT INFORMATION
The magnitude of pulling force exerted on a pipe string during PVC pipe is much stiffer than the pipe material most
pulled-in-place type installation methods depends on a commonly used for HDD and other trenchless methods
number of factors, including: HDPE pipe. This has led some designers to wonder if PVC is
too rigid to be used for these types of applications. In fact,
The length of the pull
stiffness and flexibility are two different properties. It is possible
The diameter of the pipe for a material to be very stiff and strong but still quite flexible.
TerraBrute CR is flexible enough for virtually any HDD or pipe
The type of soil bursting operation, and can be installed to a much tighter
Selection of drilling fluid. radius than other PVC products. In fact, since TerraBrute CR is
more flexible than the drilling rods, there is virtually no way to
TerraBrute CR has been designed to withstand extremely high over bend the pipe. In addition, the high stiffness of the
pulling forces in order to perform under even the toughest material means that there is very little deformation of the pipe
conditions. While most projects will use only a fraction of the string during pulling operations. As a result, appurtenances
ultimate strength of TerraBrute CR, the extra strength acts as such as services and hydrant leads can be installed
an insurance policy against unexpected conditions. immediately after pulling operations are completed.
TerraBrute CRs ultimate pull strength has been verified by One of the most important characteristics of the TerraBrute CR
laboratory tests, and can be calculated using a semiempirical joint is that it allows significant joint deflection. A significant
design method derived by researchers at the University of portion of the bending is taken up by the joints, which reduces
Western Ontario (UWO). The following table shows both the the amount of stress exerted on the pipe bell from bending.
ultimate pulling capacity of the product (no safety factor) as This allows TerraBrute CR to be installed to a much tighter
well as the recommended maximum pulling capacity (2:1 radius than other PVC products.
safety factor)
The table below shows how much TerraBrute CR can be
deflected at the joint during pullback operations, as well as
how much the pipe barrel itself can be bent. Most projects will
involve both pipe bending and joint deflection, often at the
same time.
Ultimate Pulling
Recommended Nominal Allowable Joint Allowable Pipe Minimum
Nominal Size Capacity
Pulling Limit Size Deflection Bending Allowable Radius
(Straight Pull)
mm Inches kN lbs kN Lbs. mm in (degrees) (degrees) meters Feet
100 4 50 11200 100 22400 100 4 8.5 5.7 24.2 79.4
150 6 110 24700 220 49500 150 6 8.5 4 27.5 90.2
200 8 115 25800 230 51700 200 8 7.5 3 32.7 107.4
250 10 187 42100 375 84300 250 10 5 2.5 45.8 150.3
300 12 275 61800 550 123600 300 12 5 2.1 48.4 158.8

Joint Assembly
PRODUCT INFORMATION
Lubricate and assemble joint as for
1 standard PVC pressure pipe.
Insert spigot up to the insertion line, aligning Line up the pins on the external half
2 the internal ring and the pin holes.
3 ring with the holes in the bell so that
the half ring
covers either the
left or right side of
the pipe
** SAFETY
GLASSES MUST
BE WORN
DURING PIN
INSTALLATION.
One Ring at a time, place ring over

4 pin holes and tap pins in until they
bottom out on the inner groove.

CYCLETOUGH PIPING SYSTEMS
CycleTough piping systems are specially

designed for applications where pressures are
PRODUCT INFORMATION
expected to cycle up and down repeatedly,

such as sewage forcemains, irrigation systems
and other applications. One of the most
important things to remember with CycleTough
systems is that the fittings are made with PVC
compound that has the same hydrostatic
design basis (HDB) as the pipe. Always specify
a complete system of pipes and fittings from
the same manufacturer to ensure matching
fittings.
Applications:
Forcemains, irrigation.
Rural water supply, water distribution and
transmission.
Standards
CycleTough Pipe
Certified to CSA B137.3 Rigid Poly (Vinyl Chloride) (PVC) Pipe
for Pressure Applications
ASTM D2241 Poly (Vinyl Chloride) (PVC) Plastic Pipe (SDR-
PR) PVC, ASTM D3139 and D2241.
NSF-PW listed for potable water
NQ 3660-950
CycleTough Fittings
Certified to CSA B137.3
Various ASTM Standards
NSF-PW
NQ 3660-950
Pressure Ratings
CycleTough pipe is available in For more information on how
long term pressure ratings from these ratings are calculated,
100 to 200 psi. please refer to section 3.
Short Term Rating (STR) Long Term Rating (LTR)

SDR
psi kPa psi kPa
41 160 1 100 100 690
32.5 200 1 380 125 860
26 256 1 770 160 1 100
21 320 2 210 200 1 380

PRODUCT INFORMATION
Pipes Fittings
IPSOD PVC pipe shall be manufactured from PVC compound Injection-molded PVC fittings shall be made from PVC
with ASTM D1784 cell class 12454. PVC pipe will have a compound with a minimum HDB of 4000 psi.
minimum hydrostatic design basis (HDB) of 4000 psi and a
short-term strength of 6400 psi. Pipe shall be certified to CSA Fabricated fittings shall be made from sections of pipe certified
B137.3. to CSA B137.3 and fittings shall also be certified to CSA
B137.3.
All pipes and fittings shall be listed to NSF Standard 61 and
shall be color coded white.
Dimensions
CycleTough pipe and fittings are manufactured with an Iron configuration is consistent with that used for Schedule piping
Pipe Size outside diameter (IPSOD). This outside diameter (sch. 40 and 80) as well as steel pipe sizes.
Series 100 (SDR41) Series 125 (SDR32.5)

Size Avg. ID Min. Wall Thickness Avg. OD Avg. ID Min. Wall Thickness Avg. OD
in mm in mm in mm in mm in mm in mm in mm
4 100 4.278 108.41 .109 2.78 4.50 114.3 4.208 106.88 .138 3.50 4.50 114.3
6 150 6.282 159.57 .162 4.12 6.63 168.3 6.194 157.32 .204 5.18 6.63 168.3
8 200 8.180 207.77 .209 5.32 8.62 219.1 8.063 204.80 .265 6.72 8.62 219.1
10 250 10.194 258.93 .262 6.66 10.75 273.1 10.049 255.24 .331 8.40 10.75 273.1
12 300 12.093 307.15 .311 7.90 12.75 323.9 11.921 302.78 .392 9.96 12.75 323.9
14 350 13.277 337.24 .341 8.66 14.00 355.6 13.090 332.49 .429 10.90 14.00 355.6
16 400 15.174 385.41 .390 9.90 16.00 406.4 14.957 379.90 .492 12.50 16.00 406.4
18 450 17.074 433.67 .437 11.10 18.00 457.2 16.823 427.31 .555 14.10 18.00 457.2
20 500 18.985 481.71 .488 12.40 20.00 508.0 18.698 474.93 .614 15.60 20.00 508.0
24 600 22.756 578.01 .587 14.90 24.00 609.6 22.431 569.74 .740 18.80 24.00 609.6
Series 160 (SDR26) Series 200 (SDR21)

Size Avg. ID Min. Wall Thickness Avg. OD Avg. ID Min. Wall Thickness Avg. OD
in mm in mm in mm in mm in mm in mm in mm
1-1/2 40 1.731 43.97 .080 2.02 1.90 48.3 1.709 43.42 .090 2.28 1.90 48.3
2 50 2.184 55.47 .091 2.30 2.38 60.4 2.137 54.29 .113 2.86 2.38 60.4
2-1/2 65 2.642 67.11 .109 2.78 2.87 73.0 2.584 65.62 .137 3.48 2.87 73.0
3 75 3.215 81.65 .135 3.42 3.50 88.9 3.146 79.91 .167 4.24 3.50 88.9
4 100 4.134 105.01 .172 4.38 4.50 114.3 4.046 102.77 .214 5.44 4.50 114.3
6 150 6.085 154.56 .255 6.48 6.63 168.3 5.957 151.30 .316 8.02 6.63 168.3
8 200 7.921 201.20 .331 8.42 8.62 219.1 7.756 197.00 .409 10.40 8.62 219.1
10 250 9.874 250.79 .413 10.50 10.75 273.1 9.665 245.49 .512 13.00 10.75 273.1
12 300 11.717 297.61 .488 12.40 12.75 323.9 11.467 291.25 .606 15.40 12.75 323.9
14 350 12.857 326.56 .539 13.70 14.00 355.6 12.589 319.77 .665 16.90 14.00 355.6
16 400 14.698 373.33 .614 15.60 16.00 406.4 14.381 365.27 .764 19.40 16.00 406.4
18 450 16.531 419.89 .693 17.60 18.00 457.2 16.180 410.98 .858 21.80 18.00 457.2
20 500 18.364 466.45 .772 19.60 20.00 508.0 17.980 456.70 .953 24.20 20.00 508.0
24 600 22.039 559.78 .925 23.50 24.00 609.6 21.580 548.12 1.142 29.00 24.00 609.6

90 Elbow G x G
PRODUCT INFORMATION
Size L R
in mm in mm in mm
2 50 1.18 29.5 0.75 18.8
2-1/2 65 1.80 45.0 1.00 25.0
3 75 2.00 50.0 1.00 25.0
4 100 2.20 55.0 1.00 25.0
6 150 2.80 70.0 1.25 31.3
8 200 4.87 121.8 1.50 37.5
45 Elbow G x G
Size L R
in mm in mm in mm
2 50 0.60 15.0 0.75 18.8
2-1/2 65 1.80 45.0 1.00 25.0
3 75 1.12 28.0 1.00 25.0
4 100 1.10 27.5 1.00 25.0
6 150 1.60 40.0 1.25 31.3
8 200 2.40 60.0 1.50 37.5
Tee G x G x G
Size C H L
2 50 1.30 32.5 1.10 27.5 7.60 190.0
2-1/2 65 1.67 41.8 1.63 40.8 9.50 237.5
3 75 1.99 49.8 1.99 49.8 10.80 270.0
4 100 2.57 64.3 2.65 66.3 12.50 312.5
6 150 3.76 94.0 3.77 94.3 14.90 372.5
8 200 4.91 122.8 4.91 122.8 21.65 541.3

Tap Service Tee - NPT Outlet
PRODUCT INFORMATION
Size C H L
2 x 1/2 50 x 15 1.40 35.0 2.15 53.8 7.10 177.5
2 x 3/4 50 x 20 1.40 35.0 2.15 53.8 7.10 177.5
2x1 50 x 25 1.40 35.0 2.15 53.8 7.10 177.5
2 x 1-1/4 50 x 32 1.40 35.0 2.15 53.8 7.10 177.5
2 x 1-1/2 50 x 40 1.40 35.0 2.15 53.8 7.10 177.5
2-1/2 x 1/2 65 x 15 1.45 36.3 2.50 62.5 7.90 197.5
2-1/2 x 3/4 65 x 20 1.45 36.3 2.50 62.5 7.90 197.5
2-1/2 x 1 65 x 25 1.45 36.3 2.50 62.5 7.90 197.5
2-1/2 x 1-1/4 65 x 32 1.45 36.3 2.50 62.5 7.90 197.5
2-1/2 x 1-1/2 65 x 40 1.45 36.3 2.50 62.5 7.90 197.5
2-1/2 x 2 65 x 50 1.45 36.3 2.50 62.5 7.90 197.5
3 x 1/2 75 x 15 1.50 37.5 2.70 67.5 9.75 243.8
3 x 3/4 75 x 20 1.50 37.5 2.70 67.5 9.75 243.8
3x1 75 x 25 1.50 37.5 2.70 67.5 9.75 243.8
3 x 1-1/4 75 x 32 1.50 37.5 2.70 67.5 9.75 243.8
3 x 1-1/2 75 x 40 1.50 37.5 2.70 67.5 9.75 243.8
3x2 75 x 50 1.50 37.5 2.70 67.5 9.75 243.8
4 x 1/2 100 x 15 1.56 39.0 3.10 77.5 10.17 254.3
4 x 3/4 100 x 20 1.56 39.0 3.10 77.5 10.17 254.3
4x1 100 x 25 1.56 39.0 3.10 77.5 10.17 254.3
4 x 1-1/4 100 x 32 1.56 39.0 3.10 77.5 10.17 254.3
4 x 1-1/2 100 x 40 1.56 39.0 3.10 77.5 10.17 254.3
4x2 100 x 50 1.56 39.0 3.10 77.5 10.17 254.3
6 x 1/2 150 x 15 1.80 45.0 3.96 99.0 13.00 325.0
6 x 3/4 150 x 20 1.80 45.0 3.96 99.0 13.00 325.0
6x1 150 x 25 1.80 45.0 3.96 99.0 13.00 325.0
6 x 1-1/4 150 x 32 1.80 45.0 3.96 99.0 13.00 325.0
6 x 1-1/2 150 x 40 1.80 45.0 3.96 99.0 13.00 325.0
6x2 150 x 50 1.80 45.0 3.96 99.0 13.00 325.0

Reducing Tee - G x G x G
PRODUCT INFORMATION
Size C H L
2 x 1-1/2 50 x 40 1.30 32.5 1.10 27.5 7.60 190.0
2-1/2 x 2 65 x 50 1.67 41.8 1.63 40.8 9.50 237.5
3 x 1-1/2 75 x 40 1.85 46.3 1.60 40.0 10.80 270.0
3x2 75 x 50 1.85 46.3 1.60 40.0 10.80 270.0
3 x 2-1/2 75 x 65 1.90 47.5 1.60 40.0 10.80 270.0
4x2 100 x 50 1.90 47.5 2.00 50.0 11.30 282.5
4 x 2-1/2 100 x 65 1.90 47.5 2.00 50.0 11.30 282.5
4x3 100 x 75 1.90 47.5 2.00 50.0 11.30 282.5
6x2 150 x 50 2.40 60.0 2.80 70.0 14.90 372.5
6 x 2-1/2 150 x 65 2.40 60.0 2.80 70.0 14.90 372.5
6x3 150 x 75 2.40 60.0 2.80 70.0 14.90 372.5
6x4 150 x 100 2.40 60.0 2.80 70.0 14.90 372.5
8x2 200 x 50 3.85 96.3 4.87 121.8 19.50 487.5
8x3 200 x 75 3.85 96.3 4.87 121.8 19.50 487.5
8x4 200 x 100 3.85 96.3 4.88 122.0 19.50 487.5
8x6 200 x 150 3.85 96.3 4.88 122.0 19.50 487.5
Cross G x G x G x G
Size C H L
4 100 4.00 100.0 4.00 100.0 12.50 312.5
6 150 4.50 112.5 4.50 112.5 16.00 400.0
Stop Coupling G x G
Size L D
in mm in mm in mm
2 50 5.00 125.0 3.35 83.8
2-1/2 65 7.14 178.5 4.15 103.8
3 75 7.00 175.0 5.00 125.0
4 100 7.40 185.0 6.13 153.3
6 150 10.00 250.0 8.73 218.3
8 200 12.30 307.5 10.62 265.5

Repair Coupling G x G
PRODUCT INFORMATION
Size L D
in mm in mm in mm
2 50 7.20 180.0 3.35 83.8
2-1/2 65 7.00 175.0 4.15 103.8
3 75 7.00 175.0 5.00 125.0
4 100 7.40 185.0 6.13 153.3
6 150 10.00 250.0 8.73 218.3
8 200 12.30 307.5 10.62 265.5
Permanent Plug Spigot

Size L
in mm in mm
1-1/2 40 2.50 62.5
2 50 2.50 62.5
2-1/2 65 3.50 87.5
3 75 3.50 87.5
4 100 3.75 93.8
6 150 4.50 112.5
Increaser Bushing - G x Sp
Size L C
in mm in mm in mm
1-1/2 x 2 40 x 50 2.40 60.0 0.20 5.0
2 x 2-1/2 50 x 65 2.40 60.0 0.20 5.0
2x3 50 x 75 3.40 85.0 0.55 13.8
2-1/2 x 3 65 x 75 3.40 85.0 0.38 9.5
2x4 50 x 100 3.00 75.0 0.40 10.0
2-1/2 x 4 65 x 100 3.00 75.0 0.40 10.0
3x4 75 x 100 3.00 75.0 0.40 10.0
2x6 50 x 150 4.30 107.5 0.50 12.5
2-1/2 x 6 65 x 150 4.30 107.5 0.50 12.5
3x6 75 x 150 4.30 107.5 0.50 12.5
4x6 100 x 150 4.30 107.5 0.50 12.5
4x8 100 x 200 5.10 127.5 0.60 15.0
6x8 150 x 200 5.10 127.5 0.60 15.0

Adapter - Flange x Gasket Bell

PRODUCT INFORMATION
Size C D L
1-1/2 40 3.85 96.3 5.00 125.0 4.25 106.3
2 50 4.75 118.8 6.00 150.0 4.75 118.8
2-1/2 65 5.50 137.5 7.00 175.0 5.75 143.8
3 75 6.00 150.0 7.50 187.5 6.50 162.5
4 100 7.48 187.0 9.02 225.5 10.52 263.0
6 150 9.55 238.8 10.97 274.3 13.48 337.0
8 200 11.75 293.8 13.50 337.5 12.00 300.0
Spigot Adapter G x Sp
Size L
in mm in mm
1-1/2 40 1.50 37.5
2 50 1.80 45.0
2-1/2 65 2.00 50.0
3 75 2.10 52.5
4 100 2.30 57.5
6 150 3.10 77.5
Male Adapter G x Male Pipe Thread

Size L
in mm in mm
1-1/2 40 1.05 26.3
2 50 1.20 30.0
2-1/2 65 1.55 38.8
3 75 2.10 52.5
4 100 2.25 56.3
6 150 2.50 62.5

Adapter Bell x Female IPT
PRODUCT INFORMATION
Size L
in mm in mm
1-1/2 40 2.60 65.0
2 50 3.00 75.0
2-1/2 65 3.80 95.0
3 75 4.10 102.5
4 100 4.40 110.0
6 150 5.40 135.0
Adapter - PE (Plain End) x Male Pipe Thread

Size L C
in mm in mm in mm
3 75 4.30 107.5 2.00 50.0
4 100 4.40 110.0 2.25 56.3
6 150 5.90 147.5 2.50 62.5

BLUE904TM PEX WATER SERVICE TUBING
Blue904 is fully certified, lightweight and flexible PEX water
service tubing. Installation friendly, Blue904 will resist
PRODUCT INFORMATION
corrosion, maximizing water flow over the lifetime of the

system.
Blue904 PEX Municipal Water service
tubing has unique features and
performance characteristics that make
it the leading alternative to copper
tubing. IPEX Blue904 conforms to CTS
OD dimensions, allowing common
compression fittings to be used.
Applications:
Water service lines that connect municipal watermains to
buildings.
Codes and Standards

Blue904 PEX water service tubing is certified to cNSFus-PW,
AWWA C904, ASTM F876, F877, F2023 and CSA B137.5,
NQ 3660-950 as requirements of the following national codes.
American Water Works Association

NSF Standards 14 & 61
American Society for Testing and Materials
Bureau de Normalisation du Qubec
Uniform Plumbing Code

BLUE904TM PEX WATER SERVICE TUBING
Short Form Specification
PRODUCT INFORMATION
Water service tubing shall be cross-linked polyethylene (PEX) The outside diameter of the pipe shall be copper tube size
tubing certified to cNSFus-PW, CSA B137.5 and ASTM F876. (CTS) and must have a standard dimension ratio (SDR) of 9.
PEX tubing shall have PPI approved pressure ratings of:
160psi @ 23C (73F), 100psi @ 82C (180F) and 80psi
@93C (200F).
Pressure Rating Jobsite Safe
Sizes Pressure Ratings Unlike copper tubing, PEX tubing has no scrap value,
eliminating the threat of jobsite theft common with copper. As
160 psi @ 73F (1100 kPa @ 23C) a result, no special storage precautions are necessary.
3/4" - 2"
100 psi @ 180F (690 kPa @ 82C)
(20mm - 50mm) Packaging and Markings
80 psi @ 200F (550 kPa @ 93C)
Blue904 is available in 100 ft and 300 ft coils and is packaged
Long Service Life in boxes for UV protection and portability. Each coil has
footage markings to assist during installation and is identified
Blue904 will resist the effects of chlorine and scaling and will
with product name, size, certifications and manufacturing date.
not corrode in soil. It is also freeze resistant due to its low
thermal conductivity when compared to copper tubing.
Dimensions
PEX Tubing may be shaped by hand to a minimum radius of 8

times the outside diameter of the tubing. External end
supports or sleeves may be required to maintain desired
position and shape.
Minimum Bend
Nominal Size I.D.
Radius
mm Inches mm inches mm inches

19 3/4 17.3 0.68 178 7
25 1 22.2 0.88 229 9
38 1-1/2 31.5 1.24 330 13
51 2 41.3 1.63 432 17
Note: When using pipe in coils and bending against the coil
direction, the minimum bending radius is 3 times the radius
given above. (e.g. 3/4" CTS pipe = 3 x 4.5" = 13.5")
Note: To avoid kinking, care should be taken when bending
the tubing in sub zero temperatures. For bending in cold
temperatures, use a minimum bend radius of 2 times that
listed in the chart.

Q-LINE WATER SERVICE TUBING
Q-Line is a composite pipe made with a layer of aluminum

sealed between two layers of a special thermoplastic designed
PRODUCT INFORMATION
for use as water service tubing. The result is a pipe with all the
advantages of both materials, and none of the weaknesses. It
has the strength of metal service tubing and will never corrode
as the metal is sealed in plastic. It rolls out flat like a metal pipe,
but it is lightweight like a plastic pipe.
Non-Conductor
Roughly 370 serious electric shock incidents occur in the U.S.
water utility industry every year1. While the AWWA has
opposed the practice of grounding to the water system for
over 80 years, it is still routinely done, despite the availability of
grounding rods and plates. Since Q-Line is a non-conductor, it
eliminates the risk of electric shock from stray currents.
Specifying
Q-line helps to eliminate the risk to municipal workers.
Effective Permeation Barrier

Chemical permeation is a real issue with small diameter
service tubing made of PE.
Q-Lines aluminum core is an effective barrier and has
been tested against the most aggressive contaminants
such as termiticides.
Zero Scrap Value

The high scrap value of copper pipe has resulted in
significant pilferage problems on job sites across North
America. This has resulted in storage problems as all
copper pipe must be properly secured each day.
Applications:
Water service lines, reclaimed water lines (purple pipe
available)
Codes and Standards

Q-Line water service tubing is certified to cNSFus-PW,
NQ 3660-950, ASTM F1282 and certified to CSA B137.9, and
meets AWWA C903 requirements as well as requirements of
the following national codes.
Uniform Plumbing Code

International Residential Code
National Standard Plumbing Code
SBCCI Standard Plumbing Code
Bureau de Normalisation du Qubec

PRODUCT INFORMATION
Water service tubing shall be composite PE-AL-PE tubing potable water and NSF CL-TD chlorine resistance
manufactured in accordance with the requirements of AWWA requirements. The service tubing shall be color coded light
C903 and certified to CSA B137.9 and ASTM F1282. It shall blue as manufactured by IPEX under the trade name Q-Line
have a long term pressure rating of 1380kPa at 23C (200 psi or approved equal.
at 73F) and 690kPa at 82C (100 psi at 180F). The pipe shall
be third-party tested and certified to comply with NSF-PW Fittings for composite PE-AL-PE tubing shall be brass water
service fittings conforming to AWWA C800.
Pressure Ratings Flow Rates

Q-Line is rated at 200 psi working pressure at 23C (73F). In Q-Line has larger inside diameters than CTS PE piping and a
addition, Q-Line is rated at 100 psi at 82C (180F). Since better flow coefficient than copper pipe (C = 150 for Q-Line
most water services operate at between 40 and 70 psi, even a versus only 100 for copper pipe.) This gives Q-Line the best
back-up of hot water from the building into the water service flow rates in the industry. And unlike copper pipe, Q-Line does
will not compromise Q-Line. not corrode or allow build-up of flow-constricting deposits on
the ID of the pipe.
Table 2 Q-Line Flow Rates
Flow Rate Head Loss (psi/100 ft) Velocity (fps) Flow Rate Head Loss (kPa/100m) Velocity (m/s)
(U.S. gpm) (I/s)
3/4" 1" 3/4" 1" 20mm 25mm 20mm 25mm
1.0 .1 0.0 .7 0.4 0.1 7.2 2.4 0.3 0.2
2.0 .5 0.2 1.3 0.8 0.2 26.1 8.8 0.6 0.4
3.0 1.0 0.4 2.0 1.3 0.3 55.3 18.7 1.0 0.6
4.0 1.8 0.6 2.6 1.7 0.4 94.2 31.8 1.3 0.8
5.0 2.7 0.9 3.3 2.1 0.5 142.4 48.1 1.6 1.0
6.0 3.8 1.3 4.0 2.5 0.6 199.6 97.4 1.9 1.2
7.0 5.0 1.7 4.6 3.0 0.7 265.5 89.7 2.2 1.4
8.0 6.4 2.2 5.3 3.4 0.8 340.0 114.8 2.6 1.6
9.0 8.0 2.7 5.9 3.8 0.9 422.9 142.8 2.9 1.8
10.0 9.7 3.3 6.6 4.2 1.0 514.0 173.6 3.2 2.0
11.0 11.6 3.9 7.2 4.6 1.1 613.3 207.1 3.5 2.2
12.0 13.6 4.6 7.9 5.0 1.2 720.5 243.3 3.8 2.5
13.0 15.7 5.3 8.5 5.5 1.3 835.7 282.2 4.1 2.7
14.0 18.0 6.1 9.2 5.9 1.4 958.6 323.7 4.5 2.9
15.0 20.5 6.9 9.9 6.3 1.5 1089.2 367.8 4.8 3.1
16.0 23.1 7.8 10.5 6.7 1.6 1227.5 414.5 5.1 3.3
17.0 25.8 8.7 11.2 7.1 1.7 1373.4 463.8 5.4 3.5
18.0 28.7 9.7 11.8 7.6 1.8 1526.8 515.5 5.7 3.7
19.0 31.7 10.7 12.5 8.0 1.9 1687.5 569.8 6.1 3.9
20.0 34.9 11.8 13.2 8.4 2.0 855.7 616.6 6.4 4.1
21.0 38.2 12.9 13.8 8.9
22.0 41.7 14.1 14.5 9.2
23.0 45.2 15.3 15.1 9.7
24.0 - 16.5 - 10.1
25.0 - 17.8 - 10.5
26.0 - 19.2 - 11.0
27.0 - 20.6 - 11.4
28.0 - 22.0 - 11.8
29.0 - 23.5 - 12.2
30.0 - 25.0 - 12.7

1
Duranceau, Schiff, Bell. Electrical Grounding, Pipe Integrity and Shock Hazard, Journal of the AWWA, July 1998, pp. 40-51
Dimensions
PRODUCT INFORMATION
Q-Line has unique inside and outside diameters that are

different both from copper and conventional PE service tubing.
Easily installed adapters that allow Q-line to be used with
standard brass fittings are widely available. Unlike PE pipe, Q-
line does not require a stiffening insert to be used.
Min. Wall Min. Bending

Nominal Size Avg. ID Avg. OD Weight Volume
Thickness Radius
in mm in mm in mm in mm lbs/100ft kg/100m U.S. gal/ft l/m in mm
3/4 20 .79 20 .10 2.5 .98 25 12.4 18.4 .025 .314 5.0 125
.040
1 25 .98 25 .14 3.2 1.26 32 21.0 31.2 .500 6.3 160

STANDARDS FOR PVC AND PVCO PRESSURE SYSTEMS
Standards and Certifications Underwriters Laboratories (UL, ULI, ULC)
PRODUCT INFORMATION
There are two main classes of standards governing PVC piping UL 1285
systems, those which define products that are certified by a
This standard is also third-party-certified and is often required
third party and those which define products that are non-
when the pipeline is used in fire-protection applications.
policed. While non-policed standards can be very useful in a
Certification methods are similar to those employed by CSA.
specification, the standards that are certified by a third party
offer the customer an additional level of quality assurance. Third- Accreditation of Standards Labs and Organizations
party certification means that an independent organization has
scrutinized the manufacturing process and QA/QC procedures While the standards discussed above are normally certified by a
for the products in question, and has verified that they meet the third party, that third party can sometimes be a separate
minimum requirements for approval. Compliance with a non- organization. For example, Intertek Warnock-Hersey is a
policed standard requires the customer to take the manufacturer laboratory accredited by the Standards Council of Canada, and
at his word that his product conforms to the standard. Most as a result, it is capable of certifying products to standards. It is
manufacturers perform accurate in-house testing and are common for Intertek Warnock-Hersey to certify a product to a
honest and up front, and if they state that their products meet a CSA standard, and NSF also has this capability.
certain standard, you can be quite certain that they do. There is
no question however, that certification by a third party provides Non-Certified Standards
a much higher degree of assurance that the products in American Water Works Association
question in fact meet the applicable standard and that they will AWWA C900 AWWA C903
perform as stated. AWWA C904 AWWA C905
AWWA C907 AWWA C909 certified by NSF for Bionax
Third-Party Certified Standards
C900, C905 and C907 all deal with PVC pressure pipe and
Canadian Standards Association (CSA)
fittings. C909 covers PVCO pressure pipe (Bionax) and C903
CSA B137.0 CSA B137.1 CSA B137.2 is for composite service piping (Q-line). AWWA standards are
CSA B137.3 CSA B137.3.1 CSA B137.5 used when specifying water transmission or service piping.
CSA B137.9
ASTM Standards (Various standards)
CSA staff visit all IPEX plants producing certified product
several times each year. In addition to witnessing ASTM Standards are referenced by all the above standards.
manufacturing and QA/QC procedures, CSA staff also inspect They cover everything from materials to manufacturing to
records, and select product samples for independent testing. testing to installation, which is why there are so many different
The CSA standards refer to a wide variety of external ASTM standards associated with our products. While they are
standards (such as ASTM standards) for items such as testing non-policed, the fact that many ASTM standards are
methods. As a result, certifying the product to a CSA standard included in policed standards means that indirectly, they are
often has the effect of indirectly certifying the product to other third-party certified standards.
standards as well.
Design and Installation Standards
Factory Mutual (FM)
AWWA C605
FM 1612
This standard provides guidance and instruction for
This third-party-certified standard is often required whenever underground installation of PVC/PVCO piping systems.
the piping system is going to be used as a fire-protection line.
In the case of FM, insurance regulations sometimes dictate the AWWA Manual M23
standard to be used. The certification methods are similar to The M23 Manual includes information for proper design and
those used by the CSA. installation of PVC and PVCO pipe. Because the AWWA
National Sanitation Foundation (NSF) C900, C905 and C909 standards are being revised, Manual
M23 will also need major revision. When using the 2002
NSF 14 NSF 61 edition of M23, it is recommended that information found in
Both of these standards are third-party-certified. The NSF 14 the Manual be supplemented by study of the most current
standard includes two major areas: material testing for edition of the three product standards.
potability and product testing for performance. Listing to this
standard means that the pipe/fitting material will have no
adverse effect on water quality and that the pipe/fitting product
will meet the performance requirements of the standard. NSF
61 includes the potability testing portion of NSF 14.

NOTES
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________

SECTION 2: PROPERTIES OF PVC PRESSURE PIPE AND PRESSURE SYSTEM DESIGN
INTRODUCTION
Properly designed and installed PVC piping systems will last Research dealing with the longevity of PVC pipe in various
virtually forever. Recent research has unearthed PVC systems conditions is on-going, however there have been a number of
that were installed in the 1930s that exhibit virtually no notable research papers presented over the years, including:
reduction in serviceability. This section focuses on the physical
AWWA Research Foundation Quantifying Future
properties of PVC pipes and fittings, as well as how to
Rehabilitation and Replacement Needs of
approach some of the conditions likely to be encountered
Watermains, 1998
during a project.
This study used a highly specialized computer model to
Various design issues will also be addressed including;
estimate the life of various materials based on past
The hydrostatic design basis (HDB) of PVC pipe performance. In the one North American city studied with a
significant amount of PVC pipe installed, PVC was rated at
Calculating pressure ratings
a minimum 100 years while concrete and ductile iron were
Hydraulics and headloss calculations rated at 85 and 60 years respectively.
Restraint design PVC Pipe Study Performance of PVC Water Main
Pipe installed in the City of Edmonton between 1977
Installation in contaminated soils and 1994
PRESSURE PIPE & DESIGN

Surge pressures in PVC pipe A comprehensive study of PVC pipe used in the Citys
PROPERTIES OF PVC
Air entrapment and proper location of air release valves water distribution system rated its service life at a minimum
of 88 years with minimal maintenance.
Thermal effects
Case Studies from Europe and North America including:
Design for cyclic fatigue
Dallas, Texas A PVC sewer pipe installed in 1973
was excavated and subjected to each of the tests
MATERIAL PROPERTIES OF PVC outlined in ASTM D3034. The results show that the
excavated pipe still met all the standards applicable
Design Life to new pipe
Designers should use a minimum 100 year design life when Denmark A PVC Sewer pipe installed in 1963 was
carrying out lifecycle costing calculations for PVC systems. excavated and testing results show that the pipe has
This is backed up both by research and real world the same material properties as newly produced pipe.
installations. Most of the pipes installed were directly into native
soil without bedding, and have performed acceptably
Current Research for over 40 years.
PVC pressure pipes have been in service for over 70 years in These research papers are available upon request from your IPEX
Europe2. Samples of 70 year old pipe have been excavated marketing representative at [email protected] or visit the
and have exhibited no reduction in serviceability. PVC pipes IPEX website at www.ipexinc.com./www.ipexamerica.com.
installed history in North America is approaching 50 years,
with a similar record for excellent service. The single most
destructive force attacking our municipal water and sewer
infrastructure is corrosion. By using materials that are immune
to electrolytic corrosion or chemical attack, designers eliminate
the single most common problem associated with buried
infrastructure.

2
Hulsmann, Nowack,70 Years of Experience with PVC Pipes Conference Paper, Plastic Pipes XII, Milan, April 2004
Design Strength for PVC Pipe Table 3 Summary of Properties for PVC Pipe
While Blue Brute pipes are casually referred to as PVC pipes,
in reality they are made of a special PVC compound designed Material Property
specifically for use in piping systems. The Hydrostatic Design
Basis (HDB) of a PVC compound is the minimum stress that Hydrostatic Design Basis (HDB) 26.6 MPa (4000 psi)
the material is able to withstand over a given time. The HDBs
of IPEX compounds are established through both short-term
and long-term testing (up to 10,000 hours sustained pressure). Short-Term Strength (STS) 44.1 Mpa (6400 psi)
By plotting the results on a logarithmic scale, the 50 or 100
year design stresses can be easily extrapolated. The diagram ASTM Cell Class (ASTM F1784) 12454
below shows a typical life line for a PVC compound.
As can be seen from the diagram, PVC compounds have: Youngs Modulus 266 Mpa (400,000 psi)
Figure 1 Stress Regression Line - Cell Class 12454

Poissons Ratio 0.38
10000
Chemical Permeation and Installation of PVC Pipe in

PROPERTIES OF PVC
Contaminated Soils
4000 There is a misconception among some designers that PVC
Stress (psi)
pipe is unsuitable for installation in areas that contain soils

contaminated by organic compounds. This misconception
stems from the fact that there have been rare occurrences
2000
where small diameter plastic service lines have been
permeated by organic chemicals. This is not an issue with
larger diameter PVC pipes because:
1000
1 10 100 1000 10000 100000 106 107 108 109 1010
(114 Years) 1. The vast majority of documented permeation incidents
HDB Intercept occurred with thin wall service pipes made of lower density
Time (hours) materials such as polybutylene or polyethylene3. These
small diameter pipes are indeed unsuitable for
contaminated soils. Only service pipe with a built in
High Short Term Strength permeation barrier (such as Q-Line) should be used in
While all IPEX PVC pressure pipes have a long-term these cases.
hydrostatic design basis of 4000 psi, in the short term their
strength is much higher 6400 psi. This means that the pipe 2. PVC pipe has an effective permeation time of many
can easily withstand extremely high short term pressures, centuries, even at extremely high levels of environmental
such as those generated by transient surges. For example, contamination. This has been conclusively proven through
although a DR18 pipe is rated at 235 psi, it routinely research4.
withstands well over 750 psi during quick burst tests. 3. The high density and non-porous finish of PVC pipe makes
Dependable Long-Term Strength it very difficult for permeation to occur. Samples of IPEX
At normal operational stress levels, the lifespan of the pressure pipe we partially filled with gasoline and sealed for
material is virtually unlimited. Because of the large reserves seven years. When the inside surface of the pipe was
of strength, even stresses that build to levels above the examined microscopically, no evidence of permeation was
normal safety factors can be accommodated. found5.
Summary of Material Properties Gaskets are the weak link when installing gasketed piping
All PVC pressure pipes are made of a proprietary PVC systems in contaminated soils. The most important
compound formulated specifically for pressure pipe consideration is the gasket material, regardless of the piping
applications. material. To ensure safe, long-term operation of the pipeline,
oil-resistant (nitrile) gaskets should always be specified.
Lastly, many designers consult chemical resistance guides for
information about installation in contaminated soils. These
guides are usually inappropriate for this application as they
typically deal with a 100% concentration of the material in
question. You should consult with your IPEX technical
representative before making any decisions with respect to
suitability for a particular application.

3 Jenkins, Thompson,Review of Water Industry Plastic Pipe Practices, AWWA Research Foundation, 1987
4 Berens, A.R., Prediction of Chemical Permeation through PVC Pipe, Journal of the AWWA, November 1985
5 Hoogensen Metallurgical Engineering Ltd.,Examination of Submitted PVC Pipe Section, Report to IPEX, December 1998
UV Resistance DESIGN CALCULATIONS
PVC pipe can become discolored when exposed to direct How to Calculate Pressure Capacity
sunlight for a long period of time. This discoloration affects only
the surface of the material (to a depth of 0.003 inches), and The ISO Equation for
does not appreciably affect the performance of the pipe. A slight thermoplastics makes
calculating required
PiD
reduction in the impact strength of the pipe occurs, while the
tensile strength and the modulus of elasticity are unaffected. If dimension ratios and 2
gasketed PVC pressure piping will be used in an exposed pressure capacities very
location, painting the surface of the pipe with a latex-based simple.
paint, or covering it with an opaque barrier will eliminate the While it is referred to as PiD
effects of U.V. exposure. the ISO Equation, it was
The vast majority of gasketed pressure piping is installed actually developed in
underground, eliminating the issue of UV exposure. 1852 for use with all
sorts of pressure vessels, PiD
Thermal Effects Pressure Derating and has been used ever 2
since. The derivation is

PVC is a thermoplastic, which means its mechanical simple.
PROPERTIES OF PVC
properties change with temperature. The pressure rating for
PVC pipe (and most other thermoplastic piping materials) is Referring to the figure, we can see that the force in the pipe
calculated at 73F (23C). Above that temperature, the tensile wall is:
strength of the material decreases, and the pressure rating
must be de-rated by the factors shown in the table below. The
maximum recommended service temperature for PVC
pressure pipe is 140F (60C). PVCO pipe uses the same table
Force =
( )
PiD
2
Therefore, the maximum stress in the pipe wall is:
, with the exception that the maximum recommended
temperature is 130F (54C).
max = PiD , where D = the average diameter of the pipe
2t
Table 4 Temperature Effects on PVC Pressure Pipe
D = Do t max = Pi(Do t)
Multiply the pressure 2t
C F
rating by these factors
32 90 0.75 But since DR = Do, then max = P1(DR 1)
t 2
38 100 0.62
43 110 0.50 The conservative design procedure of PVC and PVCO pipe
49 120 0.40 requires that a safety factor be applied to the Hydrostatic
54 130 0.30 Design Basis (HDB) in order to arrive at a hydrostatic design
Stress (S). This design stress then becomes the maximum
60 140 0.22
allowable stress in the material. It is important to note that the
short and long term strengths of each material are different
Thermal Effects Expansion and Contraction
and, therefore, the short-term and long-term design stresses
While buried applications seldom involve significant temperature will be different.
variations, applications such as bridge crossings or casing
The safety factors for all PVC/PVCO pressure pipes in North
installations can have temperature variations. When considering
America have traditionally been either 2.0 or 2.5, depending
the use of unrestrained joints or TerraBrute CR joints, expansion
on the application and the standard governing the design. The
and contraction should be calculated per length of pipe. If the
new standards are moving towards a safety factor of 2.0 for all
joints are restrained using conventional restrainers, or a solvent
cases. However, since not all of the standards have been
cemented joint is used, expansion and contraction should be
published, the information below conservatively continues to
calculated using the full length of restrained pipe.
use the Manual M23 safety factor of 2.5 for short term
Expansion Expansion Expansion Expansion stresses.
Material Coefficient Coefficient Coefficient Coefficient
in/in/F in/100ft/10F mm/mm/C mm/10m/10C S = max
SF
PVC 3.0 x 10-5 0.36 5.4 x 10-5 5.4
-5
PVCO 3.1 x 10 -5
0.36 5.4 x 10 5.4 P(DR 1) P = 2S
S =
HDPE 12.0 x 10 -5
1.44 14 x 10-5
21.6 2 (DR 1)
Ductile Iron 0.62 x 10-5 0.07 1.1 x 10-5 1.1
-5 -5
This form of the equation allows the pressure capabilities of a
Concrete 0.55 x 10 0.07 1.0 x 10 1.0
given dimension ratio to be quickly and easily calculated.
Steel 0.65 x 10-5 0.08 1.2 x 10-5 1.2

Calculating a Pressure Rating (CSA) or Class The table below shows both the LTR and the STR for various
(AWWA) thicknesses of PVC pipe:
There are two ratings for every PVC pipe a long term pressure Long Term Rating
rating (LTR) which is used for evaluating working pressure Short Term Rating
SDR LTR* (2:1 S.F.)
capacity, and a short term pressure rating (STR) designed for STR* (2.5:1 S.F.) (psi)
(psi)
evaluating surge and pressure capability.
To calculate an STR, simply apply the ISO equation using the 51 128 80
short term strength:
41 160 100
S = max
32.5 200 125
SF
26 256 160
Recall that:
25 264 165
Sstr = 6400 = 3200 psi
2.0 18 376 235
For short term stresses, AWWA standards set the safety factor 14 488 305
PROPERTIES OF PVC
STR = 2(3200) = 160 psi

*Values have been rounded down to the nearest 5 psi
(41 1)
(SF) = 2.0. Using the short term strength gives: For PVCO pipe:
Therefore for DR41 pipe, the STR is given by
Short Term Rating Long Term Rating
4000 = 2000 psi Pressure Class
Sltr = (psi) (psi)
2
For long term stresses, the safety factor is also set at 2.0: 235 301 235
LTR = 2(2000) = 100 psi

(41 1) Calculating Friction Headloss in PVC Piping
Using the HDB gives: Systems
Applying the ISO Equation: One of the advantages in using PVC pipe is that its smooth
inside finish dramatically reduces friction headloss when
compared to other materials. As a result, pumping costs are
lower and flows are higher when considering the same
nominal diameter between materials.
The Hazen-Williams equation is one of the most commonly
used methods for calculating friction headloss in a pipeline. It
allows the friction headloss to be easily calculated for any
piping system using flow coefficients that reflect the roughness
of the piping material. Research has established that the
Hazen-Williams flow coefficient for PVC pipe can vary between
155 to 165 for both new and previously used PVC pipe6.
Therefore, a conservative coefficient of 150 is appropriate for
all design situations. This value is also recommended by the
AWWA M23 Design Manual.
V = 1.318Cr0.63S0.54 in USCS Units

V = 0.8492Cr0.63S0.54 in SI Units
Where:
V = average pipe velocity, ft/s (m/s)
C = Hazen-Williams Friction factor (150 for PVC Pipe)
R = Hydraulic radius (D/4 for a full pipe), ft (m)
S = Hydraulic gradient or frictional head loss per unit
length of pipe, ft/ft, (m/m)
6
Uni-Bell PVC Pipe Association, Handbook of PVC Pipe Design and Construction, fourth edition, (August 2001)
Comparing Headloss Among Various Piping Materials Figure 2 Pipe Material
For any given nominal diameter of pipe, there are two factors Headloss - 200 mm Pipe at 25 L/s
which will largely dictate the headloss per unit length:
SDR9 HDPE
1. Internal diameter It is the internal diameter of the pipe that 0.006 CL52 DI
should be used for hydraulic calculations, not the nominal
Headloss, m/m
0.005 DR18 PVC
diameter. A larger internal diameter promotes a greater fluid
0.004
flow and therefore a lower headloss.
0.003
2. Internal friction coefficient While internal diameter is 0.002
important, the influence of the pipelines internal finish 0.001
should not be neglected. While PVC and other plastics can
0
sustain a smooth inside surface indefinitely, other materials
Pipe Material
tend to become rougher as a result of corrosion by-
products forming over the long term. As a result, older iron
pipes have been shown to have friction factors less than Calculating Surge Pressures PVC Pipe
100. Surge pressures (water hammer) are generated in a piping

While experimental data has shown that the C factor can be system whenever the fluid flowing in that system changes
PROPERTIES OF PVC
as high as 155-165 for both new and used PVC pipe, AWWA velocity. These changes in velocity can be caused by many
M23 Manual recommends a C factor of 150 for PVC7. things, including:
The operation of valves and pumps
Table 5 Hazen-Williams C-Factors Entrapped air being expelled
Material C Factor Changes in demand
Plastic (PVC, PVCO & HDPE) 150 There are two main types of surge pressures - transient surges
that occur as the system moves from one steady state
Iron (new) 130 condition to another (ie: the closing of a single valve), and
cyclic surges, that occur as part of the normal operation of
Iron (20 yrs old) 100 some types of pipelines. A good example of this is a sewage
forcemain, where a pump is activated each time the level in a
Comparing various materials it can be seen that PVC pipe has wet well reaches a certain point.
a much lower headloss at any given flow than other non- The magnitude of pressure surges is dependent upon a
plastic piping materials: number of things, including the type of fluid being pumped,
Class 52 iron pipe has a slightly larger inside diameter than the magnitude of the velocity change, and also the type of
DR18 PVC, but its low long-term C factor of 100 or less pipe material. Rigid piping materials typically generate much
results in poor flow characteristics. higher surge pressures than flexible systems, which are able to
absorb much more of the shock generated by a surge. In
SDR9 HDPE has a high C factor of 150, however it has a addition, the high short term strength of PVC allows it to have
much thicker pipe wall and thus has a much smaller inside a much higher safety factor against short term pressures than
diameter than PVC DR18. other piping materials.
The calculation of transient effects in a large piping system
(regardless of the piping material) is a complicated procedure
requiring considerable expertise. Fortunately, there are many
engineering firms that are highly qualified to undertake this
type of analysis. IPEX has worked closely with some of these
experts, and we would be happy to refer interested designers
to them. We highly recommend that detailed transient analysis
be performed on all systems, particularly large diameter
systems.
While a detailed analysis can be beneficial, it is possible to
calculate the magnitude of individual surges in a pipeline using
the elastic wave theory of surge analysis. The magnitude of the
surge pressure caused by a rapidly closing valve, for example,
is related to the rate of change of the flow, while the rate of
travel of the pressure wave is related to the speed of sound in
the fluid (modified by the piping material).

7 nd
AWWA Manual M23, 2 Edition PVC Pipe Design and Installation, 2002, American Water Works Association
8
Pump Handbook Third Edition Karassik, messina, Cooper & Heald, pp.8.36
Calculating Wave Velocity Pipe Calculating Surge Pressures PVCO Pipe
a = 4,660 For PVCO pipe, DR is not used. Instead, Do/t is the dimension
(1+ (k/E) (DR 2) based variable for calculating wave velocity. The modulus of
elasticity for calculating surge pressures is 500,000 psi. Using
Where: the equations above and the PVCO values, the surge pressure
for a velocity change of 0.3 m/s (1.0 fps) in PC 235 PVCO
a = Wave velocity, ft/s
pipe is 14.6 psi.
K = Bulk fluid modulus (300,000 psi for water)
Air Entrapment in Pipelines
E = Modulus of Elasticity for the pipe (400,000 psi
for PVC and 500,000 psi for PVCO) Air in pipelines can cause significant difficulties in any pipeline
system, and should be avoided wherever possible. This can
Surge Pressure PVC Pipe be accomplished by careful design of the pump or gravity
Once the wave speed has been calculated, the maximum inlet, employing proper filling and testing procedures, laying
pressure surge can be calculated using the equation: the pipe to grade wherever possible and by properly siting and
sizing air release valves.
P = a(V) Some of the problems caused by air entrapment include:

PROPERTIES OF PVC
(2.31) g 1. Air pockets can reduce the amount of cross sectional area
available for fluid flow at some points in the pipeline. This
Where:
can result in higher headloss and fluctuations in flow rates
a = wavespeed (ft/s) caused by air movement
V = maximum velocity change (ft/s) 2. Flow fluctuations can cause surge pressures in the pipeline
g = acceleration due to gravity (32.2 ft/s2) 3. Release or venting of the air can cause extremely high
surge pressures.
P = maximum pressure surge (psi)
Sources of Air in Pipelines
Applying the equations to all DRs of PVC pipe, assuming a 1
ft/s (0.3 m/s) stoppage, gives the results in the table below: The most common air sources are:
Entrapment of air during filling operations
SDR PVC Surge Pressure (psi)
Entrapment at the pump or gravity inlet
51 10.8 Release of dissolved air from the fluid in the pipeline
41 11.4 Air intake from air release valves
32.5 12.8 Problems Associated with Air Entrapment
26 14.5 The key problem with air entrapment is that at some point the
25 14.7 air may be vented in an uncontrolled way. As an air pocket
travels along a pipeline, it may reach an area where it can be
18 17.4 vented. This could be at an air release valve (good) or perhaps
at a gasketed joint (bad). The gasketing systems in most
14 19.8 pipelines are designed to work with water, not air. While in most
cases the gasket will hold back a high pressure air pocket, at
some point the gasket may be blown out of the joint, causing a
Vacuum Pressures rapid release of air. Since the air can be vented extremely
While pipe joints are tested to 10.8 psi to meet CSA quickly, the air pocket collapses at an extremely high rate. The
Standards, IPEX has simulated negative pressures far in water surges toward the orifice created by the blown gasket,
excess of full vacuum (14.7 psi) by applying external but cannot be expelled at the same velocity as the air due to its
pressures in excess of 100 psi. This proves conclusively that much higher density. The result is a rapid deceleration of the
IPEX pipe joints can easily withstand full vacuum pressures. flow and a huge transient shock wave sometimes at a
magnitude that can cause pipe failure.

Air Release Valves Nominal Size Max Filling Rate
Air release valves are designed to exhaust air under various
In mm gpm L/s
different pressure conditions in the pipeline, while restricting
the flow of liquid. Air release valves are different from 4 100 40 2.5
Air/Vacuum release valves in that Air/Vacuum release valves
have a much larger orifice and are designed to exhaust or 6 150 87 5.5
intake very large volumes of air, such as during the filling or 8 200 157 9.9
draining process. The orifice size for an air release valve is
generally between 1/16" and 1/4" diameter, while air/vacuum 10 250 245 15
release valves can be between 1" and 8".
12 300 353 22
A third type of valve combines the two functions, and is called
a combination air/vacuum release valve. It contains both a 14 350 480 30
large and a small orifice, the larger being open during filling 16 400 627 39
and draining operations, and the smaller being open
continuously to exhaust any air that might collect during 18 450 793 50
normal operation of a pipeline.

20 500 979 61
PROPERTIES OF PVC
Automatic air release valves with a riser diameter to main pipe
ratio, d/D, in the order of 0.01 should be used when untrained 24 600 1410 89
personnel fill or test the pipeline. Air release valves in this size 30 750 2203 139
range tend to limit the passage of air and allow time for the
water to slow down before reaching the vent. 36 900 3173 200
Hydrants are not useful for the venting of air from pipelines. 42 1050 4318 272
The reason is that hydrant leads typically are located at the 3
oclock or 9 oclock position on a pipeline. Air vents must be 48 1200 5640 355
located at high points (ie at 12 oclock) to be effective.
Further References:
Pipeline Testing and Air Entrapment Perhaps the most easily accessible work on the subject of air
The initial filling and testing of a pipeline is one of the most entrapment in pipelines was a film produced in the late 1960s
critical events in the lifetime of a pipeline system. The reason is at Colorado State University. It was commissioned by a major
that the potential for air entrapment is highest during this pipe manufacturer and clearly shows the effect of air
period. As a result, Design Engineers should include details entrapment in pipelines and the importance of properly sizing
and procedures covering filling and testing in their project and situating air release valves. Contact your IPEX technical
specifications: representative for a copy on CD.
1. Pipelines should be installed at a grade which results in a

minimum of high points. Abrupt transitions and sharp peaks
should be avoided.
2. Automatic air and vacuum release valves should be
properly sized and installed at all high points or other areas
where air could be expected to accumulate
3. The average water velocity when filling the pipeline should
not exceed 1 ft/s (0.3 m/s)
4. All air should be purged from the pipeline before checking
for leaks or performing pressure or acceptance tests on the
system
5. If a large quantity of water is needed to increase the
pressure during testing, then entrapped air or a leak is
possible. Testing should be discontinued until the source of
the problem is identified

Cyclic Design for PVC Pipes
Fatigue is a well known phenomenon that can affect many A worked example of a cyclic design for a sewage forcemain
different materials. Only when a piping system is subjected to can be found in section 3.
extreme cyclic loading conditions does fatigue in PVC pipe
Further Reading:
become a design factor. Fortunately, there has been a great
deal of research done on this topic, and some recent research Vinson, H.W.: Response of PVC Pipe to Large, Repetitive
completed by Dr. A. Moser at Utah State University has Pressure Surges Proceedings of the International Conference
contributed greatly to the understanding of this phenomenon. on Underground Plastic Pipe (March 1981)
Dr. Moser has determined that the number of cycles to failure Moser, Folkman, Jeffrey:Long-Term Cyclic Testing of 6 inch
(C) of PVC pipe is a function of the average stress in the pipe PVC Pipe Utah State University, (March 2003)
walls, as well as the amplitude of the cycles. This builds on
previous work done by H.W. Vinson that based the cycles to Cyclic Design for PVCO Pipes
failure only on the maximum stress in the material. Research has shown that PVCO pipe has more cyclic-fatigue
While cyclic loading is possible in many different applications, it resistance than PVC pipe does. However, the PVC-type
is typically encountered in sewage forcemain and irrigation design curves in Figure 3 have not been developed for PVCO.
applications (Most water distribution mains or transmission The design approach recommended for PVCO pipe is to treat
PROPERTIES OF PVC
mains have relatively constant pressures.) Any application that the PVCO pipe as PVC pipe of the same pressure class. Verify
has pumps starting up and shutting down at regular intervals that the PVC pipe is adequate for the design conditions and
(ie more than a couple of times per day) should be analyzed then recognize that the actual PVCO pipe provides an
using Dr. Mosers method. additional safety factor against cyclic fatigue.
The following graph shows how the average stress and the
amplitude are related to the number of cycles to failure.
Figure 3 Resulting Cyclic-Failure Curves for PVC

Stress
Amplitude Resulting Cyclic-Failure Curves for PVC
(psi)
3000
2000
1500
1000
700
500
300
200
150
100
70
50
40
30
20
3000
2500
2000
Average Stress (psi)
1500
1000
500
Positive
Negative
0 Boundary
102 103 104 105 106 107 108 109 1010 1011 1012 1013
Cycles to Failure

Thrust Restraint in Gasketed Piping Systems Concrete Thrust Blocks
Resisting Thrust at Fittings and Valves At each point in the line where thrust forces will develop, pour
a concrete block between the fitting and undisturbed native
At many locations in a pressurized pipeline, an imbalance in soil at the side of the trench. Use plywood sheets to form the
hydrostatic forces may occur as a result of the pipeline block and control the pour so that the area of contact with the
configuration. These unbalanced forces are called thrust undisturbed trench will provide the necessary support.
forces. Thrust forces can occur at any point in a piping system
where the direction or the cross-sectional area of the Bearing Strength of Undisturbed Soils
waterway changes. Pipeline installers must balance these
Organic Material (such as Peat, etc.) . . . . . . . . . .0 psf
forces by means of thrust blocks or mechanical restraint.
Soft Clay . . . . . . . . . . . . . . . . . . . . . . . . . . . . .500 psf
Three areas that require restraint are described below.
Sand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1000 psf
at valves Sand and Gravel . . . . . . . . . . . . . . . . . . . . . .1500 psf
Sand & Gravel with Clay . . . . . . . . . . . . . . . .2000 psf
All valves must be anchored. This includes valves installed in a Sand & Gravel Cemented with Clay . . . . . . .4000 psf
chamber or in line with the pipe, whether it is operated Hard Pan . . . . . . . . . . . . . . . . . . . . . . . . . . .5000 psf
frequently or only once a year.

These soil bearing capacities are approximate and
PROPERTIES OF PVC
conservative. For greater design precision, IPEX recommends
that soil bearing tests be carried out by a competent soils
engineer.
The recommended bearing area to be established by the
concrete pour may be given by the engineer. The area (ft.)
may also be calculated by determining the total thrust
generated at the fitting. Simply divide the bearing strength of
the soil into the thrust developed (lbs force), as found in the
accompanying table. The result is the area of the soil required
to resist the thrust (A). The area calculated will be for the area
of concrete up against the trench wall (i.e. the back side of the
block).
Install anchor rods around the valve body or through the

mounting lugs and embed the rods in a concrete pour
beneath the valve. Valves installed in chambers must also be
anchored in this fashion. The critical time for restraint of valves
is during opening or closing.
at changes in direction (vertical or horizontal)
Fittings such as elbows, tees, or dead ends, must be
restrained since they involve a significant directional change for
the fluid.
at reductions in size Thrust Force
area A =
Bearing Strength of Soil
The thrust component at reductions in size will depend on the
amount of the reduction, and must be adequately restrained.

Table 6 Thrust Developed per 100 psi Pressure Typical thrust block locations
(lbs. force) Trim the trench bearing area using hand tools to be sure of
Note: Pre-cast thrust blocks should not be placed directly undisturbed soil.
against PVC fittings.
Pipe Diameter Valves & Dend 90 45 11

22 Bends
in mm Ends, Tees Bends Bends Bends
4 100 1810 2560 1390 635 320
6 150 3740 5290 2860 1370 690
8 200 6430 9100 4920 2320 1170
10 250 9680 13680 7410 3610 1820
12 300 13690 19350 10470 5080 2550 This type of hydrant foundation acts as a thrust block, as an
anchorage against frost heave and eliminates washouts from
14 350 18380 25990 14100 6100 3080 wastewater drain.

PROPERTIES OF PVC
16 400 23780 33630 18280 7960 4020 Resisting Vertical Thrust

18 450 29860 42230 22970 10060 5080 Where the pipeline will change direction downwards to pass
under a creek bed or roadway, etc., upward thrust will be
20 500 36640 51820 28180 12440 6280 developed at the fitting. Anchor the fitting as though it were a
24 600 52280 73930 40200 17940 9060 valve, and ensure that the concrete base is keyed into
undisturbed soil.
30 750 80425 113737 61557 31500 15800
36 900 115200 162929 88181 45000 22600
42 1050 155500 219950 119000 60700 30500
48 1200 202700 286700 155200 79000 39800
Resisting Thrust in Very Poor Soils

Where the pipeline passes through soils having little or no
bearing strength, thrust forces may be restrained by the
encasement of the fitting in concrete and the extension of this
pour to form a monolith having sufficient inertia to resist the
thrusts. It may also be possible to loop tie rods around the
Straps should be 2 inches (50 mm) wide or greater.
fitting and anchor the tie rods into an upstream concrete pour
across the trench in more stable soils. Mechanical thrust
restraints may also be used in these cases.

Holding Pipe to Steep Slopes Assembly, Installation and testing of PVC Pressure
Normal bedding practices for pipelines installed up a hill will be Pipe Systems
sufficient to prevent backsliding and decoupling. When the Detailed information on how to install IPEX pressure pipes and
height of cover is less than 6 feet (1.8 m), and the soil fittings can be found in IPEXs Installation Guide for PVC
conditions are marginal, and where the slope is greater than Pressure Pipe and Fittings. This guide contains complete
20 (36% slope), a special anchoring method may be information on:
desirable. One recommended procedure is to lay the pipe with
the bells facing uphill and pour a concrete block behind the Receiving and handling pipe shipments
bells and keyed into the undisturbed trench sidewalls. Usually Trench preparation
every third length of pipe will need to be anchored in this
fashion to achieve a stable condition. The use of solvent Lowering pipe into the trench
welded joints for short sections of the pipeline may also be
Assembling joints
considered on steep slopes.
Curvature of the pipeline.
Mechanical Thrust Restraints
Assembling to valves and appurtenances
Several mechanical thrust restraint devices are available which

clamp to the wall of the pipe and tie back to a mating Machining and chamfering the pipe
PROPERTIES OF PVC
collar on the fitting or the pipe bell. The use of these
Tapping, flanges and sleeves
devices may provide the entire thrust restraint
necessary at the Outside diameter considerations
fitting, in sizes up
to 48 inches (1200 Backfilling and installing bedding
mm). The use of Pressure testing the pipeline
several thrust
restraints to tie Installing the pipeline through a casing
together two or Lubricant usage tables.
three lengths of pipe on either
side of the fitting may be desirable to enlist the clamping effect The Guide is available from your IPEX rep. or visit our technical
of the backfill around the pipe barrel. library at www.ipexinc.com or www.ipexamerica.com.
When a thrust restraint device is used, the maximum pressure

in the pipeline (usually the test pressure) must not exceed the
pressure rating of the restraint device.
It is important to use restraints that are specifically tested and
approved for use with PVC and/or PVCO pipe. Also, it is
essential that the bolt-torque values provided by the restraint
manufacturer be complied with by the installer.

NOTES
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________

SECTION 3 DESIGN EXAMPLES
INTRODUCTIONS
Three design examples are presented in this section:

1. PVC sewage forcemain this example shows the design method for a low-pressure line that is subjected to significant
recurring surges. Cyclic fatigue controls the design.
2. Large-diameter PVC transmission line this example illustrates the concept of changing the DR of the pipes in the pipeline
as system pressures allow. Four different DRs are included.
3. High-velocity PVCO pipeline experiencing extreme change in velocity. This line undergoes significant occasional surge
pressure, but the ability of plastic pipe to withstand short-term loads means that occasional surge does not control the
design.
Design Example #1: Sewage Forcemain AWWA C905 PVC Pipe

Select the appropriate pipe size and pressure rating for a sewage forcemain with the following characteristics:
Peak Flow = 450 L/s (7130 gpm)
Elevation Change (static head): 30 meters (98 feet)
Length: 3000 meters (9850 feet)
Average pump cycles per day: 36
System peak pressure during controlled pump operations: 500 kPa (73 psi)
Minimum pressure during controlled pump operations: 200 kPa (29 psi)
Minimum design life: 50 years
Step 1 Select an initial nominal pipe size and pressure rating
A maximum velocity of 1.5 m/s (5 ft/s) is typical in forcemain design.
Q
Q = vA A =
v
Where,
A = required pipe cross sectional area, m2
V = fluid velocity, m/s
DESIGN EXAMPLES
Q = Flow, m3/s
0.450m3/s
A = = 0.3m2
1.5m/s
Required diameter:
D2 4a 4(0.3)
a = D= = = 0.618m = 618mm is the required diameter
4
Static pressure is 298 kPa (43 psi). Therefore select 600mm (24") nominal diameter SDR51 (pressure rated 80 psi) for initial
calculations.
600mm SDR51 Inside Diameter = 630 mm (24.8").
Note: The purpose of these initial calculations is to select a nominal pipe size and pressure rating, so the required diameter
numbers do not have to match. It is more important to select the proper pipe that corresponds with the initial system static
head. This will give a basis for further calculations of dynamic head and surge pressures in the next steps

Step 2 Calculate dynamic head (friction and minor losses) and total system head
In this step the Hazen-Williams equation is used to calculate the friction losses in the system. For this example we will neglect
the minor losses through fittings and valves. For systems with large numbers of fittings, the minor losses should be calculated as
they can be significant. Note that the appropriate C factor for PVC pipe is 150.
Hazen-Williams Equation:
1 1
hf = 10.654
()( )
Q
C
0.54 1
D4.87
L = 10.654
( 0.450m3/s
150 )(
0.54 1
)
(0.630m)4.87
3000m = 6.5m
The headloss due to friction is 6.5 meters of head or 63 kPa (9 psi). This friction head is added to the static head to get the total
system head Note: When using the Hazen-Williams equation with imperial units use the proper imperial form of the equation
shown in section 2.
hsys = 30m + 6.5m = 36.5m or 358kPa (52 psi)

Therefore, SDR51 with a pressure rating (PR) of 80 psi is adequate for the working pressure requirements of this system.
Step 3 Calculate the short term (surge) requirements of the system
In section 2 a method to calculate the surge pressure for a given velocity change in a PVC pipe system was shown. The results
of those calculations will be used here without reproducing the actual calculations again. To see exactly how these numbers
were determined, refer to Calculating Surge Pressures in Section 2.
First calculate the actual maximum velocity of a 450 L/s flow in 600mm SDR51:
Q .450m3/s
Q = va = = 1.44m/s
a
(
(0.630m)2
4 )
For every 0.3 m/s change in velocity, the surge pressure generated in SDR51 is 75 kPa (10.8psi).
Ps =
( 1.44m/s
0.3 )
75kPa = 361kPa (52.3 psi)
DESIGN EXAMPLES
From Section 2 the short term rating (STR) of SDR51 is 880 kPa (128psi)
Short term requirements of the system: 358 kPa + 361 kPa = 719 kPa (104 psi)
In this case SDR51 is slightly under designed for the short term rating, so we reiterate the design using SDR41 with an STR of
130 psi. Since the I.D. is slightly different and the surge generated slightly higher we re-calculate steps 1 to 3 to obtain the
following results:
hsys = 30m + 7.1m = 37.1m or 364 kPa (52.8 psi)
Ps =
( 1.48m/s
0.3 )
79 = 389kPa (56.4 psi)
Short term requirements of the system: 364 kPa + 389kPa = 753 kPa (109 psi)
STR of SDR41 = 130 psi (>109 psi) therefore adequate for long-term and short-term requirements

Step 4 Cyclic Analysis
Recent research by Dr. A. Moser at Utah State University with respect to cyclic fatigue in PVC pipes has both simplified and
improved the accuracy of cyclic calculations. Note that the pressures used for the cyclic analysis are those that will occur during
controlled start-up and shut down operations. The majority of todays pumping systems are equipped with soft start/stop
capabilities, thus minimizing system shocks. The short-term system peak pressure (in this case 108 psi) is often not appropriate
for cyclic analysis as it is the peak pressure that would be attained only during uncontrolled events (ie: a power outage), and is
not cyclic in nature.
It was given that there are 36 cycles a day which means 36 startups and 36 shut downs for a total of 72 surge events per day.
Controlled max system pressure: 500 kPa (73 psi) {given}
Controlled minimum pressure: 200 kPa (29 psi) {given}
Calculate the average system stress:
(Pmax + Pmin) (DR1) = (500 kPa + 200 kPa)(411) = 7000 kPa (1020 psi)
avg =
4 4
Calculate the stress amplitude:
(Pmax Pmin) (DR1) = (500 kPa 200 kPa)(411) = 3000 kPa (438 psi)
amp =
4 4
DESIGN EXAMPLES

Stress
(psi)
3000
2000
1500
1000
700
500
300
200
150
100
70
50
40
30
20
3000
2500
2000
1500
1000
997
500
Positive
Negative
0 3x10 6
Boundary
102 103 104 105 106 107 108 109 1010 1011 1012 1013
Cycles to Failure
DESIGN EXAMPLES
Determine the predicted number of cycles to failure using Mosers curves. From the figure above, the predicted cycles to failure
are roughly 3 x 106 or 3,000,000 cyclic life pump starts/stops.
Calculate cyclic life:
Number of events: 72 per day x 365days/year = 26,280 per year
Events to failure: 3,000,000
Cyclic life = 3,000,000/26280 = 152 years
Safety factor = 152 years / 100-year design life = 1.52 < 2.0 required
SDR51 is slightly under-designed for cyclic fatigue, so the next thicker pipe (SDR41) is analysed. Using the same method, the
following results are obtained:
Average stress = 6 200 kPa (900 psi)
Stress amplitude = 2 200 kPa (320 psi)
Predicted cycles to failure are approximately 18,000,000.
Cyclic life = 680 years
This provides a safety factor against cyclic failure of 6.8, which exceeds the required safety factor of 2.0.
Therefore, SDR41 is adequate for the design conditions.

Design Example #2: Sewage Forcemain ASTM F1483 PVCO Bionax Pipe
Select the appropriate pipe size and pressure rating for a sewage forcemain with the following characteristics:
Peak Flow = 100 L/s (1590 gpm)
Static Pressure: 400 kPa (58 psi)
Length: 5000 meters (16400 feet)
Average pump cycles per day: 36
System peak pressure during controlled pump operations: 620 kPa (90 psi)
Minimum pressure during controlled pump operations: 180 kPa (26 psi)
Minimum design life: 100 years
Step 1 Select an initial nominal pipe size and pressure rating
A maximum velocity of 1.5 m/s (5 ft/s) is typical in forcemain design.
Q
Q = vA A =
v
Where,
A = required pipe cross sectional area, m2
V = fluid velocity, m/s
Q = Flow, m3/s
0.100m3/s
A = = 0.067m2
1.5m/s
Required diameter:
D2 4a 4(0.067)
a = D= = = 0.291m = 291mm is the required diameter
4
Static pressure is 400 kPa (58 psi). Therefore select 6300mm (12") nominal diameter PR160 (pressure rated 160 psi) for initial
calculations.
DESIGN EXAMPLES
300mm PR160 Inside Diameter = 309 mm (12.2").
Note: The purpose of these initial calculations is to select a nominal pipe size and pressure rating, so the required diameter
numbers do not have to match. It is more important to select the proper pipe that corresponds with the initial system static
head. This will give a basis for further calculations of dynamic head and surge pressures in the next steps
Step 2 Calculate dynamic head (friction and minor losses) and total system head
In this step the Hazen-Williams equation is used to calculate the friction losses in the system. For this example we will neglect
the minor losses through fittings and valves. For systems with large numbers of fittings, the minor losses should be calculated as
they can be significant. Note that the appropriate C factor for PVC pipe is 150.
Hazen-Williams Equation:
1 1
hf = 10.654
Q
C ()( )0.54
1
D4.87
L = 10.654
( 0.100m3/s
150 )(
0.54
1
)
(0.309m)4.87
5000m = 21.3m = 209 kPa
The loss due to friction is 209 kPa (30 psi). This friction head is added to the static head to get the total system head Note:
When using the Hazen-Williams equation with imperial units use the proper imperial form of the equation shown in section 2.
hf = 400 kPa + 209 kPa = 609 kPa (88 psi)

Therefore, PR160 Bionax pipe with a pressure rating (PR) of 160 psi is adequate for the working pressure requirements of this
system.

Step 3 Calculate the short term (surge) requirements of the system
In section 2 a method to calculate the surge pressure for a given velocity change in a PVC pipe system was shown. The results
of those calculations will be used here without reproducing the actual calculations again. To see exactly how these numbers
were determined, refer to Calculating Surge Pressures in Section 2.
First calculate the actual maximum velocity of a 100 L/s flow in 300mm PR160:
Q .100m3/s
Q = va = = 1.33m/s
a
(
(0.309m)2
4 )
For every 0.3 m/s change in velocity, the surge pressure generated in PR160 is 80 kPa (11.6 psi).
Ps =
( 1.33m/s
0.3 )
80 kPa = 356 kPa (51.6 psi)
From Section 2 the short term rating (STR) of PR160 is 1380 kPa (200psi)
Short term requirements of the system: 609 kPa + 356 kPa = 965 kPa (140 psi)
STR of PR160 = 200 psi (>140 psi) therefore adequate for long-term and short-term requirements
Step 4 Cyclic Analysis
Recent research by Dr. A. Moser at Utah State University with respect to cyclic fatigue in PVC pipes has both simplified and
improved the accuracy of cyclic calculations. Note that the pressures used for the cyclic analysis are those that will occur during
controlled start-up and shut down operations. The majority of todays pumping systems are equipped with soft start/stop
capabilities, thus minimizing system shocks. The short-term system peak pressure (in this case 108 psi) is often not appropriate
for cyclic analysis as it is the peak pressure that would be attained only during uncontrolled events (ie: a power outage), and is
not cyclic in nature.
It was given that there are 36 cycles a day which means 36 startups and 36 shut downs for a total of 72 surge events per day.
Controlled max system pressure: 620 kPa (90 psi) {given}
Controlled minimum pressure: 180 kPa (26 psi) {given}
DESIGN EXAMPLES
Calculate the average system stress:
(Pmax + Pmin) (DR1) = (620 kPa + 180 kPa)(411) = 5000 kPa (729 psi)
avg =
4 4
Calculate the stress amplitude:
(Pmax Pmin) (DR1) = (620 kPa 180 kPa)(411) = 2750 kPa (401 psi)
amp =
4 4

Stress
(psi)
3000
2000
1500
1000
700
500
300
200
150
100
70
50
40
30
20
3000
2500
2000
1500
1000
997
500
Positive
Negative
0 9x10 6
Boundary
102 103 104 105 106 107 108 109 1010 1011 1012 1013
Cycles to Failure
DESIGN EXAMPLES
Determine the predicted number of cycles to failure using Mosers plot.
From the plot, the predicted cycles to failure are roughly 9 x 106 pump starts and stops
Calculate cyclic life:
72 events per day x 365 = 26,280 events per year
0 x 106/26280 = 342 years
Therefore, SDR41 is more than adequate for the application.

Design Example #3: Transmission Pipe (Taken from AWWA M23 - PVC Pipe Design & Installation Manual)
This analysis of a relatively simple pipeline will illustrate the use of the design principles discussed in this guide section. PVC pipe
standards offer a variety of pipe strengths and sizes. Ideally, the designer will make selections that minimize capital and operating
costs while maintaining an adequate design safety factor.
The project is a 20,000' long PVC water transmission main designed for an ultimate capacity of 4,000 gpm (5.76 mgd).
The profile of the pipeline is shown below. Water is being pumped to a ground storage tank (point f) with a maximum water level of
35' from the floor. The centerline of the discharge end of the main, at the tie-in to the storage tank, will be 5' below the tank floor.
Key stations and their elevations along the pipeline are:
Point Station Elevation at Pipe Centerline (ft)
a 0 + 00 600
b 45 + 00 670
c 75 + 00 720
d 115 + 00 800
e 165 + 00 940
f 200 + 00 940
Figure 4 Pipeline Profile
Energy Grade Line

1,032
Tank
960 e
940
f 165+00
888
DESIGN EXAMPLES
Elevation (ft)
816 d
800
115+00
744 c
720
75+00 b
672 670
45+00 Pump House

a
600 600
Ft 19,998 16,665 13,332 9,999 6,666 3,333 0
The objective of the design process will be to select proper DRs of PVC for appropriate sections of pipeline while never
exceeding the PR nor the WPR of the pipe at any point. An effort will be made to select DRs that meet the design criteria while
providing optimum economic value for the utility or owner.
The key determinant of PVC pressure pipe design is the internal pressure. The pipe dimensions can be found in the AWWA pipe
standards. For this example, AWWA Standard C905, Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings,
14 In. through 48 In. (350mm through 1,200mm), for Water Transmission and Distribution, was used. The exact pipe dimensions
are required to determine the flow velocity. The total pressure in the pipeline at any point is the sum of the static head, the friction
loss, and the pressure rise as a result of sudden velocity changes. For simplicity, the selection of PVC pipe in this example will be
limited to four PRs in CIOD only (PR 235, 165, 125 and 100).

Step 1 Determine the maximum flow velocity
Assume that 20" PVC pipe will be used. In AWWA C905, the heaviest wall shown to be available in 20" pipe is DR 18. The
assumption of beginning with the heaviest wall (i.e., the lowest DR) is recommended for most designs in the initial stage. The
first assumption may be confirmed or revised as the design is developed.
Average ID = Average OD 2 (minimum wall thickness x 1.06)
Note: The tolerance on wall thickness is approximately +12%. There is no minus tolerance. Manufacturers will generally aim to
produce PVC pressure pipe with wall thicknesses about 6% over minimum.
Assume: 20" DR 18 per AWWA C905
Avg. ID = 21.60 2 (1.200 x 1.06)

= 19.05 in = 1.59 ft
V = Q/A
Where,
Q = Flow in ft3/sec = 4,000 gpm or 8.91 ft3/sec
A = area, ft2
V = velocity, ft/sec
A = (3.14) (1.59/2)2 = 1.98 ft2
Therefore,
V = 8.91/1.98 = 4.5 ft/sec
Because the velocity is within an acceptable range, the design may proceed with 20" pipe.
Step 2 Determine the surge factor
DESIGN EXAMPLES
In a transmission pipeline, the amplitude and location of the surge pressure envelope will often be analyzed by computer. For this
example, the assumption has been made that the maximum surge pressure will be equal to an instantaneous stop-page of flow
at full velocity. In practice, the costs of pipe materials may be significantly reduced through the use of appropriate surge control
devices and proper pipeline operating procedures.
The pressure rise resulting from a V = 4.5 ft/sec instantaneous velocity change in PVC pressure pipes can be charted as
follows:
Dimension Ratio, DR 1 ft/sec Surge, Ps' (psi) V x Ps' (psi)
41 11.4 51.3
32.5 12.8 57.6
25 14.7 66.2
18 17.4 78.3

Step 3 Determine the WPR for each of the DRs of Step 2
The WPR is a job-specific pressure rating of the pipe, taking into account the maximum possible surges versus the short-term
strength of the pipe. The WPR may be either higher or lower than the PR of the pipe, depending on the flow conditions. The
lower value between the WPR and the PR should be used as the upper limit for system steady-state operating pressure.
WPR = STR V x Ps'
DR STR (psi) V x Ps' (psi) WPR (psi) PR (psi)
41 130 51.3 78.7 100
32.5 165 57.6 107.4 125
25 215 66.2 148.8 165
18 300 78.3 221.7 235
It can be seen that the governing parameter for the pressure design of this example will be the WPR analysis since it is lower
than the PR of each DR.
Step 4 Determine the friction loss f under full-flow conditions
Continue to assume DR 18 for this calculation because this pipe will produce slightly greater losses than the other DRs under
consideration. The result will be conservative for all design operations.
The Hazen-Williams equation is convenient to use:
Q1.852
f = 0.2083 (100/C)1.852
di4.8655
Where,
f = friction head, ft of water per 100 ft of pipe

di = inside diameter of pipe, in.
DESIGN EXAMPLES
Q = flow, gpm
C = flow coefficient, 150 for PVC
Substituting for 20" PR 235 pipe, where d = 19.05 in
f = 0.273 ft of water per 100 ft of pipeline
= 0.118 psi per 100 ft (station) of pipeline

Step 5 Determine the pressures at key points in the pipeline under steady-state, full-flow conditions
This pressure, P, at any point is the sum of the static head as a result of difference in elevations and the friction loss.
Referring to Figure 4, the pressure at key points can be calculated as follows:
Starting at the storage tank:
Station 200 + 00
Static Head = 980 940 = 40 ft

or 40 ft x (0.43 psi/ft) = 17.3 psi
Station 165 + 00
Static Head = (980 940) ft x (0.43 psi/ft) = 17.3 psi

Friction Head = (3,500 ft) x (0.118 psi/100 ft) = 4.1 psi
Total Head = 21.4 psi
Station 115 + 00

Station 75 + 00

Station 45 + 00
DESIGN EXAMPLES
Station 0 + 00

The pressure, P, at each of the key points are summarized as follows:
Point Station Static Head (psi) Friction Head (psi) Pressure, P (psi)
f 200 + 00 17.3 0 17.3
e 165 + 00 17.3 4.1 21.4
d 115 + 00 77.4 10.0 87.4
c 75 + 00 111.8 14.8 126.6
b 45 + 00 133.3 18.3 151.6
a 0 + 00 163.4 23.6 187.0

Step 6 Determine the appropriate DR of pipe for each section of the pipeline
From previous calculations in Step 3, DR 18 PVC pressure pipe has a working pressure rating 221.7 psi. For the next greater
DR, DR 25, the WPR is 148.8 psi. Therefore, DR 18 is selected to start out at the pumphouse until a point in the system where
the operating pressure, P, drops to be equal to the WPR of DR 25. At this point, DR 25 may be used. Subsequent steps will
determine the starting points for DR 32.5 as well as DR 41.
It can be seen from the above summary of pressures by section that the transition to DR 25 will occur between
Stations 45 + 00 and 75 + 00, in section bc. To pinpoint the exact location, the pressure gradient for that section must
be calculated.
(Pc + Pb)
P(bc) =
Station Length of bc
126.6 psi 151.6 psi
=
(75 45) x (100 ft)
= 0.83 psi/100 ft
The length beyond Station 45 + 00 (point b) can be calculated as follows:
Station Length WPR(DR 25) Pb

=
P(bc)
(148.8 psi) (151.6 psi)
=
0.83 psi/100 ft
= 337 ft (i.e., at 337 ft downstream of Station 45 + 00)
Therefore, begin using DR 25 at Station 48 + 37.
Similarly, the transition point for DR 32.5 can be found.
From the summary of pressures and knowing the WPR of DR 32.5 is 107.4 psi, DR 32.5 can be used between
Station 75 + 00 and Station 115 + 00, i.e., section cd.
DESIGN EXAMPLES
First, calculate the pressure gradient in section cd.
(Pd Pc)
P(cd) =
Station Length of cd
87.4 psi 126.6 psi
=
(115 75) x (100 ft)
= 0.98 psi/100 ft
Next, the Station Length beyond Station 75 + 00 can be calculated:
Station Length WPR(DR 32.5) Pc

=
P(cd)
(107.4 psi) (126.6 psi)
=
0.98 psi/100 ft
= 1,959 ft (i.e., at 1,959 ft downstream of Station 75 + 00)
Therefore, begin using DR 32.5 at Station 94 + 59.

Similarly, it can be calculated where DR 41 usage may begin.
From review of the summary of pressures and knowing the WPR of DR 41 is 78.7 psi, the range for DR 41 begins between
Station 115 + 00 and Station 165 + 00, i.e., section de.
First, calculate the pressure gradient in section de.
(Pe Pd)
P(de) =
Station Length of de
21.4 psi 87.4 psi
=
(165 115) x (100 ft)
= 1.32 psi/100 ft
Next, the Station Length beyond point d:
Station Length WPR(DR 41) Pd

=
P(de)
(78.7 psi) (87.4 psi)
=
1.32 psi/100 ft
= 659 ft (i.e., at 659 ft downstream of Station 115 + 00)
Therefore, DR 41 may begin usage at Station 121 + 59 and continue for the duration of the pipeline up to its terminus at the
reservoir.
Distance from Pumphouse (ft) Use 20 in. Pressure Gradient (psi)
0 4.837 DR 18 (PR 235) 187.0 148.8
DESIGN EXAMPLES
4,837 9,459 DR 25 (PR 165) 148.8 107.4
9,459 12,159 DR 32.5 (PR 125) 107.4 78.7
12,159 20,000 DR 41 (PR 100) 78.7 17.3
The design for internal pressure may be summarized as follows:

In this example of a 3.8 mile pipeline, the designer has the opportunity to make significant cost savings through the use of
several PVC pipe pressure ratings. Computer modeling may disclose even further potential savings by showing exactly where
and how surge control is most effective. (Note that the above pipe selection was made assuming that the potential exists for the
instantaneous stoppage of flow.)
If the pipeline is operated in a cycle mode (i.e., like some sewage force mains), an analysis of fatigue life should be made. Both
present and future modes of operation should be examined.

NOTES
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________

SECTION FOUR: APPENDICES
APPENDIX A: REFERENCES
1 Duranceau, Schiff, Bell. Electrical Grounding, Pipe Integrity and Shock Hazard,
Journal of the AWWA, July 1998, pp. 40-51
2 Hulsmann, Nowack,70 Years of Experience with PVC Pipes Conference Paper,
Plastic Pipes XII, Milan, April 2004
3 Jenkins, Thompson,Review of Water Industry Plastic Pipe Practices,
AWWA Research Foundation, 1987
4 Berens, A.R., Prediction of Chemical Permeation through PVC Pipe,
Journal of the AWWA, November 1985
5 Hoogensen Metallurgical Engineering Ltd., Examination of Submitted PVC Pipe Section,
Report to IPEX, December 1998
6 Uni-Bell PVC Pipe Association, Handbook of PVC Pipe Design and Construction,
fourth edition, (August 2001)
APPENDICES

APPENDIX B: REFERENCE TABLES AND CONVERSION CHARTS
Table B-1 Pipe Capacity Table B-5 Pressure Conversion
Table B-2 Weights of Water Table B-6 Flow Conversion
Table B-3 Decimal & Millimeter Equivalents of Fractions Table B-7 Temperature Conversion
Table B-4 Volume Conversion Table B-8 Length Conversion
TABLE B-1 PIPE CAPACITY
Pipe Size Outside Diameter IPS OD Pipe Volume for 1 foot length of pipe
inches inch feet cm in3 ft3 cm3 US Gal Imp Gal
1/4 0.250 0.021 0.098 0.589 0.0003 9.648 0.003 0.002
3/8 0.375 0.031 0.148 1.325 0.001 21.708 0.006 0.005
1/2 0.500 0.042 0.197 2.355 0.001 38.591 0.010 0.008
3/4 0.750 0.063 0.295 5.299 0.003 86.831 0.023 0.019
1 1.000 0.083 0.394 9.420 0.005 154.366 0.041 0.034
1-1/4 1.250 0.104 0.492 14.719 0.009 241.196 0.064 0.053
1-1/2 1.500 0.125 0.591 21.195 0.012 347.322 0.092 0.076
2 2.000 0.167 0.787 37.680 0.022 617.462 0.163 0.136
3 3.000 0.250 1.181 84.780 0.049 1,389.290 0.367 0.306
4 4.000 0.333 1.575 150.720 0.087 2,469.849 0.652 0.543
5 5.000 0.417 1.969 235.500 0.136 3,859.139 1.019 0.849
6 6.000 0.500 2.362 339.120 0.196 5,557.159 1.468 1.222
8 8.000 0.667 3.150 602.880 0.349 9,879.395 2.610 2.173
10 10.000 0.833 3.937 942.000 0.545 15,436.554 4.078 3.396
12 12.000 1.000 4.724 1,356.480 0.785 22,228.638 5.872 4.890
14 14.000 1.167 5.512 1,846.320 1.068 30,255.646 7.993 6.655
16 16.000 1.333 6.299 2,411.520 1.396 39,517.578 10.439 8.693
18 18.000 1.500 7.087 3,052.080 1.766 50,014.435 13.212 11.002
20 20.000 1.667 7.874 3,768.000 2.181 61,746.216 16.312 13.582
24 24.000 2.000 9.449 5,425.920 3.140 88,914.551 23.489 19.559
TABLE B-2 WEIGHTS OF WATER
Weight
Units of Volume
pounds kilograms
1 US Gallon 8.35 3.79
1 Imperial Gallon 10.02 4.55
APPENDICES
1 litre 2.21 1.00
1 cubic yard 1,685.610 765.267

1 cubic foot 62.430 28.343
1 cubic inch 0.036 0.016
1 cubic cm 0.002 0.001
1 cubic metre 2,210.000 1,000.000

TABLE B-3 DECIMAL & MILLIMETER EQUIVALENTS OF FRACTIONS
Inches Inches
Fractions Decimals Millimeters Fractions Decimals Millimeters
1/64 0.015625 0.397 33/64 0.515625 13.097
1/32 0.03125 0.794 17/32 0.53125 13.494
3/64 0.046875 1.191 35/64 0.546875 13.891
1/16 0.0625 1.588 9/16 0.5625 14.288
5/64 0.078125 1.984 37/64 0.578125 14.684
3/32 0.09375 2.381 19/32 0.59375 15.081
7/64 0.109375 2.778 39/64 0.609375 15.478
1/8 0.125 3.175 5/8 0.625 15.875
9/64 0.140625 3.572 41/64 0.640625 16.272
5/32 0.15625 3.969 21/32 0.65625 16.669
11/64 0.171875 4.366 43/64 0.671875 17.066
3/16 0.1875 4.763 11/16 0.6875 17.463
13/64 0.203125 5.159 45/64 0.703125 17.859
7/32 0.21875 5.556 23/32 0.71875 18.256
15/64 0.23475 5.953 47/64 0.734375 18.653
1/4 0.250 6.350 3/4 0.750 19.050
17/64 0.265625 6.747 49/64 0.765625 19.447
9/32 0.28125 7.144 25/32 0.78125 19.844
19/64 0.296875 7.541 51/64 0.796875 20.241
5/16 0.3125 7.938 13/16 0.8125 20.638
21/64 0.328125 8.334 53/64 0.828125 21.034
11/32 0.34375 8.731 27/32 0.83475 21.431
23/64 0.359375 9.128 55/64 0.859375 21.828
3/8 0.375 9.525 7/8 0.875 22.225
25/64 0.390625 9.922 57/64 0.890625 22.622
13/32 0.40625 10.319 29/32 0.90625 23.019
27/64 0.421875 10.716 59/64 0.921875 23.416
7/16 0.4375 11.113 15/16 0.9375 23.813
29/64 0.453125 11.509 61/64 0.953125 24.209
15/32 0.46875 11.906 31/32 0.96875 24.606
31/64 0.484375 12.303 63/64 0.984375 25.003
1/2 0.500 12.700 1 1.000 25.400
TABLE B-4 VOLUME CONVERSION
Units of Volume in3 ft3 yd3 cm3 m3 liter U.S. gal. Imp. gal.
cubic inch 1 0.00058 - 16.387 - 0.0164 0.0043 0.0036
cubic foot 1728 1 0.0370 28,317.8 0.0283 28.32 7.481 6.229
APPENDICES
cubic yard 46,656 27 1 - 0.7646 764.55 201.97 168.8

cubic centimeter 0.0610 - - 1 - 0.001 0.0003 0.0002
cubic meter 61,023.7 35.31 1.308 - 1 1000 264.17 220.0
liter 61.02 0.0353 0.0013 1000 0.001 1 0.2642 0.22
U.S. gallon 231 0.1337 0.0050 3785.4 0.0038 3.785 1 0.8327
Imp. gallon 277.42 0.1605 0.0059 4546.1 0.0045 4.546 1.201 1

TABLE B-5 PRESSURE CONVERSION
Units of Pressure atm bar lb/in2 lb/ft2 kg/cm2 kg/m2 inch H20
atmosphere (atm) 1 0.987 0.068 - 0.968 - 0.002
bar 1.013 1 0.069 - 0.981 - 0.002
pound per square inch (psi) 14.7 14.5 1 0.007 14.22 0.001 0.036
pound per square foot (psf) 2,116 2,089 144 1 2,048 0.205 5.2
kilogram per square centimeter 1.033 1.02 0.07 - 1 0.0001 0.003
kilogram per square meter 10,332 10,197 703 4.88 10,000 1 25.4
inch of water (H20) (4C) 406.78 401.46 27.68 0.192 393.7 0.039 1
inch of mercury (Hg) (0C) 29.921 29.53 2.036 0.014 28.96 0.003 0.074
inch of air (15C) 332,005 327,664 22,592 148.7 321,328 32.13 816.2
foot of water (4C) 33.9 33.46 2.307 0.016 32.81 0.003 0.083
foot of air (15C) 27,677 27,305 1,883 13.07 26,777 2.678 0.006
millimeter of mercury (0C) 760 750 51.71 0.36 735.6 0.074 1.868
millimeter of water (4C) 10,332 10,197 703 4.88 10,000 1 25.4
kilopascal (kP) 101.3 100 6.89 0.048 98.07 0.01 0.249
Newton per square meter - - - 0.021 - 0.102 0.004
Units of Pressure inch Hg inch air ft H20 ft air mm Hg mm H20 kilopascal N/m2
atmosphere (atm) 0.033 - 0.029 - 0.001 - 0.01 -
bar 0.034 - 0.03 - 0.001 - 0.01 -
pound per square inch (psi) 0.491 - 0.434 0.001 0.019 0.001 0.145 -
pound per square foot (psf) 70.73 0.006 62.43 0.076 2.784 0.205 20.89 0.021
kilogram per square centimeter 0.035 - 0.03 - 0.001 - 0.01 -
kilogram per square meter 345.3 0.031 304.8 0.373 13.6 1 101.97 0.102
inch of water (H20) (4C) 13.6 0.001 12 0.015 0.535 0.039 4.015 0.004
inch of mercury (Hg) (0C) 1 - 0.883 0.001 0.039 0.003 0.295 -
inch of air (15C) 11,096 1 9,794 12 436.8 32.13 3,277 3.106
foot of water (4C) 1.133 - 1 - 0.045 0.003 0.335 -
foot of air (15C) 924.7 0.083 816.2 1 36.4 2.678 273.1 0.273
millimeter of mercury (0C) 25.4 0.002 22.42 0.027 1 0.074 7.5 0.008
millimeter of water (4C) 345.3 0.031 304.8 0.373 13.6 1 101.97 0.102
kilopascal (kP) 3.386 - 2.99 0.004 0.133 0.01 1 0.001
Newton per square meter - 3.277 - 0.273 0.008 0.102 0.001 1
APPENDICES

TABLE B-6 FLOW CONVERSION
Units of Flow Rate US gps US gpm US gph US gpd Imp gps Imp gpm Imp gph Imp gpd liters/sec liters/min liters/hr liters/day
US gal/sec (gps) 1 0.017 - - 1.2 0.02 - - 0.264 0.004 - -
US gal/min (gpm) 60 1 0.017 0.001 72.06 1.2 0.02 0.001 15.85 0.264 0.004 -
US gal/hr (gph) 3,600 60 1 0.042 4,323 72.06 1.2 0.05 951.02 15.85 0.264 0.011
US gal/day (gpd) 86,400 1,440 24 1 103,762 1,729.40 28.82 1.2 22,824 380.41 6.34 0.264
Imperial gal/sec 0.833 0.014 - - 1 0.017 - - 0.22 0.004 - -
Imperial gal/min 49.96 0.833 0.014 0.001 60 1 0.017 0.001 13.2 0.22 0.004 -
Imperial gal/hr 2,997.60 49.96 0.833 0.035 3,600 60 1 0.042 791.89 13.2 0.22 0.009
Imperial gal/day 71,943 1,199 19.98 0.833 86,400 1,440 24 1 19,005 316.76 5.279 0.22
Liters/sec 3.79 0.063 0.002 - 4.55 0.076 0.001 - 1 0.017 - -
Liters/min 227.12 3.785 0.063 0.003 272.77 4.55 0.076 0.003 60 1 0.017 0.001
Liters/hr 13,627 227.12 3.785 0.158 16,366 272.77 4.55 0.189 3,600 60 1 0.042
Liters/day 327,060 5,451 90.85 3.785 392,782 6,546 109.11 4.55 86,400 1,440 24 1
Cubic ft/sec (cfs) 0.134 0.002 - - 0.161 0.003 - - 0.035 0.001 - -
Cubic ft/min (cfm) 8.02 0.134 0.002 - 9.633 0.161 0.003 - 2.119 0.035 0.001 -
Cubic ft/hr (cfh) 481.25 8.02 0.134 0.006 577.96 9.63 0.161 0.007 127.13 2.119 0.035 0.001
Cubic ft/day (cfd) 11,550 192.5 3.21 0.134 13,871 231.18 3.853 0.161 3,051.20 50.85 0.848 0.001
Acre in/min 0.002 - - - 0.003 - - - 0.001 - - -
Acre in/hr 0.133 0.002 - - 0.159 0.003 - - 0.035 - - -
Acre in/day 3.182 0.053 0.001 - 3.821 0.064 0.001 - 0.841 0.001 - -
Cubic m/sec 0.004 - - - 0.005 - - - 0.001 - - -
Cubic m/min 0.227 0.004 - - 0.273 0.005 - - 0.06 0.001 - -
Cubic m/hr 13.628 0.227 0.004 - 16.366 0.273 0.005 - 3.6 0.06 0.001 -
Cubic m/day 327.06 5.451 0.091 0.004 392.78 6.546 0.109 0.005 86.4 1.44 0.024 0.001
Units of Flow Rate ft3/sec ft3/min ft3/hr ft3/day Acre in/min Acre in/hr Acre in/day m3/sec m3/min m3/hr m3/day
US gal/sec (gps) 7.48 0.125 0.002 - 452.6 7.54 0.31 264.2 4.4 0.073 0.003
US gal/min (gpm) 448.8 7.48 0.125 0.005 27,154 452.6 18.86 15,850 264.2 4.403 0.183
US gal/hr (gph) 26,930 448.83 7.481 0.312 1.629E+06 27,154 1,131 951,019 15,850 264.17 11.007
US gal/day (gpd) 646,317 10,772 179.53 7.481 3.910E+07 651,703 27,154 2.282E+07 380,408 6,340 264.17
Imperial gal/sec 6.229 0.104 0.002 - 376.8 6.28 0.26 220 3.67 0.061 0.003
Imperial gal/min 373.73 6.229 0.104 0.004 22,611 376.8 15.7 13,198 220 3.666 0.153
Imperial gal/hr 22,424 373.73 6.229 0.259 1.357E+06 22,611 942.1 791,889 13,198 220 9.165
Imperial gal/day 538,171 8,970 149.49 6.229 3.256E+07 542,656 22,611 1.901E+07 316,756 5,279 220
Liters/sec 28.32 0.472 0.008 - 1,713 28.6 1.19 1,000 16.67 0.278 0.012
Liters/min 1,699 28.32 0.472 0.2 102,790 1,713 71.38 60,000 1,000 16.67 0.694
Liters/hr 101,941 1,669 28.32 1.18 6.167E+06 102,790 4,283 3.600E+06 60,000 1,000 42.67
Liters/day 2,446,575 40,776 679.6 28.32 1.480E+08 2.467E+06 102,790 8.640E+07 1.440E+06 24,000 1,000
Cubic ft/sec (cfs) 1 0.017 - - 60.5 1.008 0.042 35.31 0.589 0.01 -
Cubic ft/min (cfm) 60 1 0.017 - 3,630 60.5 2.52 2,119 35.31 0.59 0.025
Cubic ft/hr (cfh) 3,600 60 1 0.042 217,800 3,630 151.25 127,133 2,119 35.31 1.471
APPENDICES
Cubic ft/day (cfd) 86,400 1,440 24 1 5.227E+06 87,120 3,630 3,051,187 50,853 847.55 35.31
Acre in/min 0.017 - - - 1 0.017 0.001 0.584 0.01 - -
Acre in/hr 0.992 0.001 - - 60 1 0.042 35.02 0.584 0.01 -
Acre in/day 23.8 0.033 0.006 - 1,440 24 1 840.55 14.001 0.233 0.001
Cubic m/sec 0.028 - - - 1.71 0.029 0.001 1 0.017 - -
Cubic m/min 1.7 0.028 - - 102.8 1.71 0.071 60 1 0.017 0.001
Cubic m/hr 101.94 1.7 0.028 0.001 6,167 102.8 4.283 3,600 60 1 0.042
Cubic m/day 2446.6 40.78 0.68 0.028 148,018 2,467 102.79 86,400 1,400 24 1

TABLE B-7 TEMPERATURE CONVERSION
F C F C F C F C F C
-60 -51 22 -5.6 50 10.0 78 25.6 160 71
-50 -46 23 -5.0 51 10.6 79 26.1 170 77
-40 -40 24 -4.4 52 11.1 80 26.7 180 82
-30 -34 25 -3.9 53 11.7 81 27.2 190 88
-20 -29 26 -3.3 54 12.2 82 27.8 200 92
-10 -23.0 27 -2.8 55 12.8 83 28.3 210 99
0 -17.8 28 -2.2 56 13.3 84 28.9 212 100
1 -17.2 29 -1.7 57 13.9 85 29.4 220 104
2 -16.7 30 -1.1 58 14.4 86 30.0 230 110
3 -16.1 31 -0.6 59 15.0 87 30.6 240 116
4 -15.6 32 0.0 60 15.6 88 31.1 250 121
5 -15.0 33 0.6 61 16.1 89 31.7 260 127
6 -14.4 34 1.1 62 16.7 90 32.2 270 132
7 -13.9 35 1.7 63 17.2 91 32.8 280 138
8 -13.3 36 2.2 64 17.8 92 33.3 290 143
9 -12.8 37 2.8 65 18.3 93 33.9 300 149
10 -12.2 38 3.3 66 18.9 94 34.4 310 154
11 -11.7 39 3.9 67 19.4 95 35.0 320 160
12 -11.1 40 4.4 68 20.0 96 35.6 330 166
13 -10.6 41 5.0 69 20.6 97 36.1 340 171
14 -10.0 42 5.6 70 21.1 98 36.7 350 177
15 -9.4 43 6.1 71 21.7 99 37.2 360 182
16 -8.9 44 6.7 72 22.2 100 37.8 370 188
17 -8.3 45 7.2 73 22.8 110 43 380 193
18 -7.8 46 7.8 74 23.3 120 49 390 199
19 -7.2 47 8.3 75 23.9 130 54 400 204
20 -6.7 48 8.9 76 24.4 140 60
21 -6.1 49 9.4 77 25.0 150 66
Degrees Celsius C = 5 (F - 32) Degrees Fahrenheit F = 9 C + 32

9 5
Degrees Kelvin T = C + 273.2 Degrees Rankine R = F + 459.7
TABLE B-8 LENGTH CONVERSION
Units of Length in. ft. yd. mile mm cm m km

inch 1 0.0833 0.0278 - 25.4 2.54 0.0254 -
foot 12 1 0.3333 - 304.8 30.48 0.3048 -
APPENDICES
yard 36 3 1 - 914.4 91.44 0.9144 -

mile - 5280 1760 1 - - 1609.3 1.609
millimeter 0.0394 0.0033 - - 1 0.100 0.001 -
centimeter 0.3937 0.0328 0.0109 - 10 1 0.01 -
meter 39.37 3.281 1.094 - 1000 100 1 0.001
kilometer - 3281 1094 0.6214 - - 1000 1
(1 micron = 0.001 millimeter)

APPENDIX C: USEFUL FORMULAS
Area of a Circle
Circumference of a Circle
Length of Circular Arc
Area of Circle Sector
Equation of a Circle (cartesian coordinates)
Equation of a Line (quadratic formula)
Basic Trigonometric Functions
Area of an Ellipse
Circumference of an Ellipse
Area of a Triangle
Area of a Trapezoid
Area of a Parallelogram
Surface Area of a Sphere
Volume of a Sphere
Surface Area of a Cylinder
Volume of a Cylinder
Surface Area of an Elliptical Tank
Volume of an Elliptical Tank
Surface Area of a Cone
Volume of a Cone
Surface Area of a Rectangular Solid
Volume of a Rectangular Solid
APPENDICES

APPENDIX C: USEFUL FORMULAS
Circle Ellipse
r
Diameter = r b
S 2 Area = x a x b
O a
Circumference = D = 2r Circumference
Area = r2 = (3 (a + b) (3a + b) (a + 3b)
Length of Circular Arc

S = x xr in degrees
( 180 )
S = xr in radians Triangle
Area of Circle Sector Area = w h
h
A = x xxr 2
in degrees 2
( 360 )
A = x 2 w
( 2
)xr in radians
Equation of a Circle (cartesian co-ordinates)

- for a circle with center (j, k) and radius (r)
(x - j)2 + (y - k)2 = r2
b Trapezoid
Equation of a line (quadratic formula)
ax + by + c = 0 h Area = 1 (b1 + b2) h
or 2
ax2 + bx + c = 0 b
x -b + b2 - 4ac
2a
Parallelogram
A Trigonometry
h Area = b h
sin = b
c
b c
cos = a b
O
a
c
B C
tan = b
a
Sine Law
9 = 6 = c = 2R
sin A sin B sin C Sphere
Cosine Law r Surface Area = 4 r2
C2 = a2 + b2 - 2ab cos C
Volume = 4 r3
b2 = a2 + c2 - 2ac cos B 3
APPENDICES
a2 = b2 + c2 - 2bc cos A

r
Cylinder
Surface Area = (2 r2) + (2 r h)
h
Volume = r2 h
Elliptical Tank
a
b
h
Surface Area
Volume = abh
2
( (
a2 + b2 h + (2 ab)
2
Cone
S
h Surface Area = r S
Volume = r2 h
r 3
Rectangular Solid
w
L Surface Area = 2 (Lw + Lh + wh)
h
Volume = L w h
APPENDICES

APPENDIX D: ABBREVIATIONS
AGA - American Gas Association
ANSI - American National Standards Institute
API - American Petroleum Institute
ASME - American Society of Mechanical Engineers
ASTM - American Society for Testing and Materials
AWWA - American Water Works Association
BOCA - Building Officials and Code Administrators
BS - British Standards Institution
CPVC - Chlorinated poly (vinyl chloride) plastic or resin
CS - Commercial Standard, see Product Standard
CSA - Canadian Standards Association
DR - Dimension Ratio
DIN - German Industrial Norms
FHA - Federal Housing Administration or Farmers Home Administration
HDB - Hydrostatic design basis
HDS - Hydrostatic design stress
IAPD - International Association of Plastics Distributors
IAPMO - International Association of Plumbing and Mechanical Officials
IPC - International Plumbing Code
ISO - International Standards Organization
JIS - Japanese Industrial Standards
NSF - National Sanitation Foundation International
PPI - Plastics Pipe Institute
PS - Product Standard when in reference to a specification for plastic pipe and fittings. These
specifications are promulgated by the U.S. Department of Commerce and were formerly known
as Commercial Standards.
PVC - Poly-(vinyl chloride) plastic, resin or compound
PVCO - Molecularly Oriented Polyvinyl Chloride Plastic
RVCM - Residual Vinyl Chloride Monomer
SCS - Soil Conservation Service
SDR - Standard Dimension Ratio
SI - International System of Units
SPI - Society of the Plastics Industry, Inc.
APPENDICES
UPC - Uniform Plumbing Code

USASI - United States of America Standards Institute (formerly American Standards Association)
WOG - Water, Oil, Gas

APPENDIX E: TABLES AND FIGURES
Table 1 Percent (%) Deflection for IPEX Centurion Pressure Pipe pg 14
Table 2 Q-Line Flow Rates pg 35
Table 3 Summary of Properties for PVC Pipe pg 40
Table 4 Temperature Effects on PVC Pressure Pipe pg 41
Table 5 Hazen-Williams C-Factors pg 43
Table 6 Thrust Developed per 100 psi Pressure (lbs. force) pg 48
Figure 1 Stress Regression Line - Cell Class 12454 pg 40

Figure 2 Pipe Material pg 43
Figure 3 Resulting Cyclic-Failure Curves for PVC pgs 46, 54 & 57
Figure 4 Pipeline Profile pg 58
APPENDICES

NOTES
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________

SALES AND CUSTOMER SERVICE
Customers call IPEX USA LLC
Toll free: (800) 463-957
www.ipexamerica.com
About the IPEX Group of Companies
As leading suppliers of thermoplastic piping systems, the IPEX

Group of Companies provides our customers with some of the
largest and most comprehensive product lines. All IPEX products
are backed by more than 50 years of experience. With state-of-
the-art manufacturing facilities and distribution centers across
North America, we have earned a reputation for product
innovation, quality, end-user focus and performance.
Markets served by IPEX group products are:
Electrical systems
Telecommunications and utility piping systems
PVC, CPVC, PP, PVDF, PE, ABS, and PEX pipe and fittings
Industrial process piping systems
Municipal pressure and gravity piping systems
Plumbing and mechanical piping systems
Electrofusion systems for gas and water
Industrial, plumbing and electrical cements
Irrigation systems
Products manufactured by IPEX Inc. and distributed in the United States by

IPEX USA LLC.
Bionax, Blue904TM, IPEX Centurion, CycleTough, IPEX FusibleTM,

Q-Line and TerraBrute CR and are trademarks of IPEX Branding Inc.
This literature is published in good faith and is believed to be

reliable. However it does not represent and/or warrant in any
manner the information and suggestions contained in this
brochure. Data presented is the result of laboratory tests and field
experience.
A policy of ongoing product improvement is maintained. This may

result in modifications of features and/or specifications without
notice.
MNMNNAIP131110 2015 IPEX IND0033U

Pressure Piping Systems Technical Manual

Uploaded by

Copyright:

Available Formats

Pressure Piping Systems Technical Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Pressure Piping Systems Technical Manual

Uploaded by

Copyright:

Available Formats

Volume I:

Blue Brute Piping Systems

Vol. 1, 4th Edition

2015 by IPEX. All rights reserved. No part of this book may

The information contained here within is based on current information

Pressure Piping Systems Design Manual

Section One: Product Information

Section Three: Design Examples

Section Four: Appendices

Pressure Piping Systems Design i

ii Pressure Piping Systems Design

Pressure Piping Systems Design 1

2 Pressure Piping Systems Design

SUMMARY OF PRESSURE PIPE AND FITTINGS TESTING

Pressure Piping Systems Design 3

Gasket Options For Contaminated Soils

Blue Brute Pipe:

Blue Brute Fittings:

4 Pressure Piping Systems Design

Short Form Specifications

DR 25 Class 165 DR 18 Class 235 DR 14 Class 305

Min. Wall Min. Wall Min. Wall

Pressure Piping Systems Design 5

Bell OD for Joint Restraint Selection

6 Pressure Piping Systems Design

Pressure Piping Systems Design 7

Single Tapped Coupling

A L 6x6x1 150 x 150 x 25 1 25 3.0 76

Double Tapped Coupling

8 Pressure Piping Systems Design

High Deflection Coupling

Tapped Plug (IPS Threads)

Pressure Piping Systems Design 9

Bionax PVCO pipe and Blue Brute PVC fittings eliminate

Although Bionax is compatible with iron fittings, IPEX

10 Pressure Piping Systems Design

Short Form Specifications

Material Color Coding

Pressure Class/Rating 165 psi @ 73F (1 150 kPa @ 23C)

Pressure Piping Systems Design 11

IPEX Centurion extends the benefits of Blue Brute to

versatility and ease of installation of IPEX Centurion

12 Pressure Piping Systems Design

Short Form Specifications

Pressure Ratings Surge Pressures

32.5 200 1 380 125 860 Surge Pressure

18 376 2 590 235 1 620 51 10.8 75

14 488 3 370 305 2 100 41 11.4 79

Bionax (PC235) 14.1 97

Pressure Piping Systems Design 13

IPEX Centurion for Gravity Applications

Table 1 Percent (%) Deflection for IPEX Centurion Pressure Pipe

14 Pressure Piping Systems Design

PR/PC 80 (SDR51) PR/PC 100 (SDR41) PR/PC 125 (SDR32.5)

Min. Wall Min. Wall Min. Wall

14 350 - - - - - - 14.6 369.7 0.37 9.5 15.3 388.6 - - - - - -

16 400 - - - - - - 16.6 420.4 0.43 10.8 17.4 442.0 - - - - - -

PR/PC 165 (DR25) PR/PC 235 (DR18) PR/PC 305 (DR14)

Min. Wall Min. Wall Min. Wall