LG Flatron l1740 l1940 Service Manual

Website:http://biz.LGservice.
com
E-mail:http://www.LGEservice.com/techsup.html
COLOR MONITOR
SERVICE MANUAL
CHASSIS NO. : CL-82
MODEL: L1740BQ (L1740BQN.AN**EP)
( ) **Same model for Service
CAUTION
BEFORE SERVICING THE UNIT,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
*To apply the MSTAR Chip.
Downloaded from www.Manualslib.com manuals search engine

CONTENTS
SPECIFICATIONS ................................................... 2 SERVICE OSD ...................................................... 13
PRECAUTIONS ....................................................... 3 TROUBLESHOOTING GUIDE .............................. 14
TIMING CHART ....................................................... 7
WIRING DIAGRAM ............................................... 18
DISASSEMBLY ....................................................... 8
BLOCK DIAGRAM ................................................... 9 EXPLODED VIEW...................................................19
DESCRIPTION OF BLOCK DIAGRAM...................10 REPLACEMENT PARTS LIST ...............................21
ADJUSTMENT ...................................................... 12 SCHEMATIC DIAGRAM ......................................... 23
SPECIFICATIONS
1. LCD CHARACTERISTICS 4. Max. Resolution
Type : TFT Color LCD Module Analog : 1280 x 1024 / 75Hz
Active Display Area : 17 inch
Pixel Pitch : 0.264 (H) x 0.264 (V) 5. POWER SUPPLY
Size : 358.5 (H) x 296.5 (V) x 17.0 (D)
Color Depth : 8bit, 16.2M colors 5-1. Power : AC 100-240V~, 50/60Hz , 1.0A
Electrical Interface : LVDS
Surface Treatment : Hard-coating(3H), Anti-Glare 5-2. Power Consumption
Operating Mode : Normally White, Transmissive mode
Backlight Unit : Top/Bottom edge side 4-CCFL MODE H/V SYNC VIDEO POWER CONSUMPTION LED COLOR
(Cold Cathode Fluorescent Lamp) POWER ON (NORMAL) ON/ON ACTIVE less than 43 W BLUE
2. OPTICAL CHARACTERISTICS STAND-BY OFF/ON OFF less than 1 W AMBER

2-1. Viewing Angle by Contrast Ratio ≥ 10 SUSPEND ON/OFF OFF less than 1 W AMBER
Left : -60° min., -70°(Typ) Right : +60° min., +70°(Typ) DPMS OFF OFF/OFF OFF less than 1 W AMBER
Top : +45° min., +60°(Typ) Bottom : -50°min., -60°(Typ)
6. ENVIRONMENT
2-2. Luminance : 200(min), 250(Typ) 6-1. Operating Temperature : 10°C~35°C (50°F~95°F)
(Ambient)
2-3. Contrast Ratio : 300(min), 450(Typ) 6-2. Relative Humidity : 10%~80% (Non-condensing)
6-3. MTBF : 50,000 HRS with 90% Confidence level
3. SIGNAL (Refer to the Timing Chart) Lamp Life : 50,000 Hours (Min)
3-1. Sync Signal
• Type : Separate Sync, Composite Sync, 7. DIMENSIONS (with TILT/SWIVEL)
SOG (Sync On Green)
Width : 394 mm (15.51'')
3-2. Video Input Signal Depth : 221.8 mm (8.73'')
1) Type : R, G, B Analog Height : 396 mm (15.59'')
2) Voltage Level : 0~0.71 V
a) Color 0, 0 : 0 Vp-p
b) Color 7, 0 : 0.467 Vp-p 8. WEIGHT (with TILT/SWIVEL)
c) Color 15, 0 : 0.714 Vp-p
3) Input Impedance : 75 Ω Net. Weight : 5.3 kg (11.69 lbs)
Gross Weight : 7.4 kg (16.32 lbs)
3-3. Operating Frequency
Horizontal : 30 ~ 83kHz
Vertical : 56 ~ 75Hz
-2-

PRECAUTION
WARNING FOR THE SAFETY-RELATED COMPONENT. WARNING
• There are some special components used in LCD BE CAREFUL ELECTRIC SHOCK !
monitor that are important for safety. These parts are
• If you want to replace with the new backlight (CCFL) or
marked on the schematic diagram and the
inverter circuit, must disconnect the AC adapter
replacement parts list. It is essential that these critical
because high voltage appears at inverter circuit about
parts should be replaced with the manufacturer’s
650Vrms.
specified parts to prevent electric shock, fire or other
hazard.
• Handle with care wires or connectors of the inverter
• Do not modify original design without obtaining written circuit. If the wires are pressed cause short and may
permission from manufacturer or you will void the burn or take fire.
original parts and labor guarantee.
Leakage Current Hot Check Circuit
TAKE CARE DURING HANDLING THE LCD MODULE AC Volt-meter

WITH BACKLIGHT UNIT.
• Must mount the module using mounting holes arranged
in four corners. Good Earth Ground
such as WATER PIPE,
• Do not press on the panel, edge of the frame strongly CONDUIT etc.
To Instrument's
or electric shock as this will result in damage to the exposed
screen. METALLIC PARTS
• Do not scratch or press on the panel with any sharp

objects, such as pencil or pen as this may result in 1.5 Kohm/10W
damage to the panel.
• Protect the module from the ESD as it may damage the
electronic circuit (C-MOS).
• Make certain that treatment person’s body are
grounded through wrist band.
• Do not leave the module in high temperature and in
areas of high humidity for a long time.
• The module not be exposed to the direct sunlight.
• Avoid contact with water as it may a short circuit within
the module.
• If the surface of panel become dirty, please wipe it off
with a softmaterial. (Cleaning with a dirty or rough cloth
may damage the panel.)
CAUTION
Please use only a plastic screwdriver to protect yourself
from shock hazard during service operation.
-3-

SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this 9. Use with this receiver only the test fixtures specified in
service manual and its supplements and addenda, read this service manual.
and follow the SAFETY PRECAUTIONS on page 3 of this CAUTION: Do not connect the test fixture ground strap
publication. to any heat sink in this receiver.
NOTE: If unforeseen circumstances create conflict
between the following servicing precautions and any of the Electrostatically Sensitive (ES) Devices
safety precautions on page 3 of this publication, always Some semiconductor (solid-state) devices can be
follow the safety precautions. Remember: Safety First. damaged easily by static electricity. Such components
commonly are called Electrostatically Sensitive (ES)
General Servicing Precautions Devices. Examples of typical ES devices are integrated
1. Always unplug the receiver AC power cord from the AC circuits and some field-effect transistors and
power source before; semiconductor "chip" components. The following
a. Removing or reinstalling any component, circuit techniques should be used to help reduce the incidence of
board module or any other receiver assembly. component damage caused by static by static electricity.
b. Disconnecting or reconnecting any receiver electrical 1. Immediately before handling any semiconductor
plug or other electrical connection. component or semiconductor-equipped assembly, drain
c. Connecting a test substitute in parallel with an off any electrostatic charge on your body by touching a
electrolytic capacitor in the receiver. known earth ground. Alternatively, obtain and wear a
CAUTION: A wrong part substitution or incorrect commercially available discharging wrist strap device,
polarity installation of electrolytic capacitors may which should be removed to prevent potential shock
result in an explosion hazard. reasons prior to applying power to the unit under test.
d. Discharging the picture tube anode. 2. After removing an electrical assembly equipped with
2. Test high voltage only by measuring it with an ES devices, place the assembly on a conductive
appropriate high voltage meter or other voltage surface such as aluminum foil, to prevent electrostatic
measuring device (DVM, FETVOM, etc) equipped with charge buildup or exposure of the assembly.
a suitable high voltage probe. 3. Use only a grounded-tip soldering iron to solder or
Do not test high voltage by "drawing an arc". unsolder ES devices.
3. Discharge the picture tube anode only by (a) first 4. Use only an anti-static type solder removal device.
connecting one end of an insulated clip lead to the Some solder removal devices not classified as "anti-
degaussing or kine aquadag grounding system shield static" can generate electrical charges sufficient to
at the point where the picture tube socket ground lead damage ES devices.
is connected, and then (b) touch the other end of the 5. Do not use freon-propelled chemicals. These can
insulated clip lead to the picture tube anode button, generate electrical charges sufficient to damage ES
using an insulating handle to avoid personal contact devices.
with high voltage. 6. Do not remove a replacement ES device from its
4. Do not spray chemicals on or near this receiver or any protective package until immediately before you are
of its assemblies. ready to install it. (Most replacement ES devices are
5. Unless specified otherwise in this service manual, packaged with leads electrically shorted together by
clean electrical contacts only by applying the following conductive foam, aluminum foil or comparable
mixture to the contacts with a pipe cleaner, cotton- conductive material).
tipped stick or comparable non-abrasive applicator; 7. Immediately before removing the protective material
10% (by volume) Acetone and 90% (by volume) from the leads of a replacement ES device, touch the
isopropyl alcohol (90%-99% strength) protective material to the chassis or circuit assembly
CAUTION: This is a flammable mixture. into which the device will be installed.
Unless specified otherwise in this service manual, CAUTION: Be sure no power is applied to the chassis
lubrication of contacts in not required. or circuit, and observe all other safety precautions.
6. Do not defeat any plug/socket B+ voltage interlocks 8. Minimize bodily motions when handling unpackaged
with which receivers covered by this service manual replacement ES devices. (Otherwise harmless motion
might be equipped. such as the brushing together of your clothes fabric or
7. Do not apply AC power to this instrument and/or any of the lifting of your foot from a carpeted floor can
its electrical assemblies unless all solid-state device generate static electricity sufficient to damage an ES
heat sinks are correctly installed. device.)
8. Always connect the test receiver ground lead to the
receiver chassis ground before connecting the test
receiver positive lead.
Always remove the test receiver ground lead last.
-4-

General Soldering Guidelines Replacement
1. Use a grounded-tip, low-wattage soldering iron and 1. Carefully insert the replacement IC in the circuit board.
appropriate tip size and shape that will maintain tip 2. Carefully bend each IC lead against the circuit foil pad
temperature within the range or 500。F to 600。F. and solder it.
2. Use an appropriate gauge of RMA resin-core solder 3. Clean the soldered areas with a small wire-bristle
composed of 60 parts tin/40 parts lead. brush. (It is not necessary to reapply acrylic coating to
3. Keep the soldering iron tip clean and well tinned. the areas).
4. Thoroughly clean the surfaces to be soldered. Use a
mall wire-bristle (0.5 inch, or 1.25cm) brush with a "Small-Signal" Discrete Transistor
metal handle. Removal/Replacement
Do not use freon-propelled spray-on cleaners. 1. Remove the defective transistor by clipping its leads as
5. Use the following unsoldering technique close as possible to the component body.
a. Allow the soldering iron tip to reach normal 2. Bend into a "U" shape the end of each of three leads
temperature. remaining on the circuit board.
(500。F to 600。F) 3. Bend into a "U" shape the replacement transistor leads.
b. Heat the component lead until the solder melts. 4. Connect the replacement transistor leads to the
c. Quickly draw the melted solder with an anti-static, corresponding leads extending from the circuit board
suction-type solder removal device or with solder and crimp the "U" with long nose pliers to insure metal
braid. to metal contact then solder each connection.
CAUTION: Work quickly to avoid overheating the
circuitboard printed foil. Power Output, Transistor Device
6. Use the following soldering technique. Removal/Replacement
a. Allow the soldering iron tip to reach a normal 1. Heat and remove all solder from around the transistor
temperature (500。 F to 600。 F) leads.
b. First, hold the soldering iron tip and solder the strand 2. Remove the heat sink mounting screw (if so equipped).
against the component lead until the solder melts. 3. Carefully remove the transistor from the heat sink of the
circuit board.
c. Quickly move the soldering iron tip to the junction of 4. Insert new transistor in the circuit board.
the component lead and the printed circuit foil, and 5. Solder each transistor lead, and clip off excess lead.
hold it there only until the solder flows onto and 6. Replace heat sink.
around both the component lead and the foil.
CAUTION: Work quickly to avoid overheating the Diode Removal/Replacement
circuit board printed foil. 1. Remove defective diode by clipping its leads as close
d. Closely inspect the solder area and remove any as possible to diode body.
excess or splashed solder with a small wire-bristle 2. Bend the two remaining leads perpendicular y to the
brush. circuit board.
3. Observing diode polarity, wrap each lead of the new
IC Remove/Replacement diode around the corresponding lead on the circuit
Some chassis circuit boards have slotted holes (oblong) board.
through which the IC leads are inserted and then bent flat 4. Securely crimp each connection and solder it.
against the circuit foil. When holes are the slotted type, 5. Inspect (on the circuit board copper side) the solder
the following technique should be used to remove and joints of the two "original" leads. If they are not shiny,
replace the IC. When working with boards using the reheat them and if necessary, apply additional solder.
familiar round hole, use the standard technique as
outlined in paragraphs 5 and 6 above. Fuse and Conventional Resistor
Removal/Replacement
Removal 1. Clip each fuse or resistor lead at top of the circuit board
1. Desolder and straighten each IC lead in one operation hollow stake.
by gently prying up on the lead with the soldering iron 2. Securely crimp the leads of replacement component
tip as the solder melts. around notch at stake top.
2. Draw away the melted solder with an anti-static 3. Solder the connections.
suction-type solder removal device (or with solder CAUTION: Maintain original spacing between the
braid) before removing the IC. replaced component and adjacent components and the
circuit board to prevent excessive component
temperatures.
-5-

Circuit Board Foil Repair At Other Connections
Excessive heat applied to the copper foil of any printed Use the following technique to repair the defective copper
circuit board will weaken the adhesive that bonds the foil pattern at connections other than IC Pins. This technique
to the circuit board causing the foil to separate from or involves the installation of a jumper wire on the
"lift-off" the board. The following guidelines and component side of the circuit board.
procedures should be followed whenever this condition is 1. Remove the defective copper pattern with a sharp
encountered. knife.
Remove at least 1/4 inch of copper, to ensure that a
At IC Connections hazardous condition will not exist if the jumper wire
To repair a defective copper pattern at IC connections use opens.
the following procedure to install a jumper wire on the 2. Trace along the copper pattern from both sides of the
copper pattern side of the circuit board. (Use this pattern break and locate the nearest component that is
technique only on IC connections). directly connected to the affected copper pattern.
3. Connect insulated 20-gauge jumper wire from the lead
1. Carefully remove the damaged copper pattern with a of the nearest component on one side of the pattern
sharp knife. (Remove only as much copper as break to the lead of the nearest component on the
absolutely necessary). other side.
2. carefully scratch away the solder resist and acrylic Carefully crimp and solder the connections.
coating (if used) from the end of the remaining copper CAUTION: Be sure the insulated jumper wire is
pattern. dressed so the it does not touch components or sharp
3. Bend a small "U" in one end of a small gauge jumper edges.
wire and carefully crimp it around the IC pin. Solder the
IC connection.
4. Route the jumper wire along the path of the out-away
copper pattern and let it overlap the previously scraped
end of the good copper pattern. Solder the overlapped
area and clip off any excess jumper wire.
-6-

TIMING CHART
VIDEO
A
E
D B
SYNC
C
<< Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >>
Dot Total Display Front Sync. Back

MODE Section Polarity Frequency Period Porch Porch Resolution
Clock (E) (A) (D) (C) (B)
1 H(Pixels) + 25.175 31.469 800 640 16 96 48 640 x 350
V(Lines) - 70.09 449 350 37 2 60
2 H(Pixels) - 28.321 31.468 900 720 18 108 54 720 X 400
V(Lines) + 70.08 449 400 12 2 35
3 H(Pixels) - 25.175 31.469 800 640 16 96 48 640 x 480
V(Lines) - 59.94 525 480 10 2 33
4 H(Pixels) - 31.5 37.5 840 640 16 64 120 640 x 480
V(Lines) - 75 500 480 1 3 16
5 H(Pixels) + 40.0 37.879 1056 800 40 128 88 800 x 600
V(Lines) + 60.317 628 600 1 4 23
6 H(Pixels) + 49.5 46.875 1056 800 16 80 160 800 x 600
V(Lines) + 75.0 625 600 1 3 21
7 H(Pixels) +/- 57.283 49.725 1152 832 32 64 224 832 x 624
V(Lines) +/- 74.55 667 624 1 3 39
8 H(Pixels) - 65.0 48.363 1344 1024 24 136 160 1024 x 768
V(Lines) - 60.0 806 768 3 6 29
9 H(Pixels) - 78.75 60.123 1312 1024 16 96 176 1024 x 768
V(Lines) - 75.029 800 768 1 3 28
10 H(Pixels) +/- 100.0 68.681 1456 1152 32 128 144 1152 x 870
V(Lines) +/- 75.062 915 870 3 3 39
11 H(Pixels) +/- 92.978 61.805 1504 1152 18 134 200 1152 x 900
V(Lines) +/- 65.96 937 900 2 4 31
12 H(Pixels) + 108.0 63.981 1688 1280 48 112 248 1280 x 1024
V(Lines) + 60.02 1066 1024 1 3 38
13 H(Pixels) + 135.0 79.976 1688 1280 16 144 248 1280 x 1024
V(Lines) + 75.035 1066 1024 1 3 38
-7-

DISASSEMBLY
#1 #2
Disassembly Hinge Cover. Remove the screws.
#3 #4 9 10 11 12 13 14
4
8
3 7
6
2
1 5
Jig
1. Open the Backcover's latch with special Jig. Unlock Latch between C/A and B/C as 1~14
2. Refer to right picture which shows the latches. sequence.
#5 #6
Disassemble back cover. Disassemble inverter shield something thin.
#7 #8
Remove the 7 screws from each side of metal Remove the 4 screws from each side of metal
frame. frame.
-8-

5V LCD Module
5V 3.3V
R,G,B LVDS
differential (Low Voltage

Differential
3.3V Reg. FE2040 & Signaling)
78D33 TR(KTA 1273)
3.3V 1.8V
1.8V FE2040
including
-9-
(ADC/LVDS/SCALER MTV412
3.3V
/INPUT SWITCHING MICOM
12V 5V
/TMDS )
BLOCK DIAGRAM
AC I nput LIPS
R,G,B, H/ V Sync
D-SUB
DESCRIPTION OF BLOCK DIAGRAM
1. Video Controller Part.

This part amplifies the level of video signal for the digital conversion and converts from the analog video signal to the
digital video signal using a pixel clock.
The pixel clock for each mode is generated by the PLL.
The range of the pixel clock is from 25MHz to 135MHz.
This part consists of the Scaler, ADC and TMDS receiver .
The Scaler gets the video signal converted analog to digital, interpolates input to 1280 X 1024 resolution signal and
outputs 8-bit R, G, B signal to transmitter.
2. Power Part.
This part consists of the 3.3V regulator to convert power which is provided, 5V in power board.
5V is provided for LCD panel Micom.
Also, 5V is converted 3.3V by regulator and 3.3V is converted 1.8V by scaler & KTA1273.
Converted power is provided for IC in the main board.
3. MICOM Part.
This part consists of EEPROM IC which stores control data and the Micom.
The Micom distinguishes polarity and frequency of the H/V sync are supplied from signal cable.
The controlled data of each modes is stored in EEPROM.
- 10 -

LIPS Board Block Diagram
12V
50 ~ 60Hz
HVDC 100KHz 5V
EMI INPUT RECTIFIER ENERGY OUTPUT RECTIFIER
COMPONENTS AND FILTER TRANSFER AND FILTER
LINE GND
100 ~ 240V
PWM PHOTO- SIGNAL

CONTROL COUPLER COLLENT-
CIRCUIT ISOLATION ION
PRIMARY SECONDARY
Operation description_LIPS
1. EMI components.
This part contains of EMI components to comply with global marketing EMI standards like FCC,VCCI CISPR,
the circuit included a line-filter, across line capacitor and of course the primary protection fuse.
2. Input rectifier and filter.

This part function is for transfer the input AC voltage to a DC voltage through a bridge rectifier and a bulk capacitor.
3. Energy Transfer.
This part function is for transfer the primary energy to secondary through a power transformer.
4. Output rectifier and filter.

This part function is to make a pulse width modulation control and to provide the driver signal to power switch,to
adjust the duty cycle during different AC input and output loading condition to achieve the dc output stabilized, and
also the over power protection is also monitor by this part.
5. Photo-Coupler isolation.
This part function is to feed back the dc output changing status through a photo transistor to primary controller to
achieve the stabilized dc output voltage.
6. Signal collection.
This part function is to collect the any change from the dc output and feed back to the primary through photo
transistor.
- 11 -

ADJUSTMENT
Windows EDID V1.0 User Manual 2. EDID Read & Write
1) Run WinEDID.exe
Operating System: MS Windows 98, 2000, XP
Port Setup: Windows 98 => Don’t need setup
Windows 2000, XP => Need to Port Setup.
This program is available to LCD Monitor only.
1. Port Setup
a) Copy “UserPort.sys” file to
“c:\WINNT\system32\drivers” folder
b) Run Userport.exe
2) Edit Week of Manufacture, Year of Manufacture,

Serial Number
a) Input User Info Data
b) Click “Update” button
c) Click “ Write” button
c) Remove all default number

d) Add 300-3FF
e) Click Start button.

f) Click Exit button.
- 12 -

SERVICE OSD
1) Turn off the power switch at the front side of the display.
2) Wait for about 5 seconds and press MENU, POWER switch with 1 second interval.
3) The SVC OSD menu contains additional menus that the User OSD menu as described below.
a) Auto Color : W/B balance and Automatically sets the gain and offset value.
b) NVRAM INIT : EEPROM initialize.(24C08)
c) CLEAR ETI : To initialize using time.
d) AGING : Select Aging mode(on/off).
e) R/G/B-9300K : Allows you to set the R/G/B-9300K value manually.
f) R/G/B-6500K : Allows you to set the R/G/B-6500K value manually.
g) R/G/B-Offset : Allows you to set the R/G/B-Offset value manually.(Analog Only)
h) R/G/B-Gain : Allows you to set the R/G/B-Gain value manually.(Analog Only)
i) MODULE : To select applied module.
BM
Video Signal
Compatible PC 15 11
Generator 6
C
PARALLEL PORT
d
se
tu
2C
No
23
RS
OFF ON
5V
EL
Control Line
F
LL
C
RA
PA
Power inlet (required)

22
Power Select Switch

R
VG ON
WE
S
(110V/220V)
PO
E
A
T
MO Power LED
CS
NI OFF
YN
TOR
VS
E ST Switch
B
B
F V-Sync On/Off Switch
(Switch must be ON.)
Figure 1. Cable Connection
- 13 -

TROUBLESHOOTING GUIDE
1. NO POWER
NO POWER
(POWER INDICATOR OFF)
CHECK POWER BOARD,

CHECK J705
NO AND FIND OUT A SHORT
VOLTAGE
POINT AS OPENING
PIN5, PIN6 (5V)?
EACH POWER LINE
YES
CHECK
NO CHECK 5VS LINE
U501 PIN 8 VOLTAGE
(OPEN CHECK)
(5V) ?
YES NO PROBLEM
CHECK KEY CONTROL

CONNECTOR ROUTINE
YES
IS U201
NO
PIN90 (3.3V) CHECK 3.3V LINE
VOLTAGE ?
YES
CHECK U201 PIN 96 NO

1 CHECK X-TAL
PULSE
YES
CHECK U201
Waveforms
1 U201-#96
- 14 -

2. NO RASTER (OSD IS NOT DISPLAYED) – LIPS
NO RASTER
(OSD IS NOT DISPLAYED)
CHECK POWER BOARD,

J705 NO AND FIND OUT A SHORT
PIN5, PIN6
POINT AS OPENING
5V?
EACH POWER LINE
YES
J705 PIN9 NO CHECK MICOM INV

2.5V? ON/OFF PORT.
YES
1. CONFIRM BRIGHTNESS
J705 PIN10 NO OSD CONTRL STATE.
5V? 2. CHECK MICOM DIM-ADJ
PORT
YES
CHECK
PULSE AS
CONTACTING SCOPE
PROBE TO CAUTION LABEL. NO
(CONTACT PROBE TO LIPS
CAUTION LABEL.
CAN YOU SEE PULSE
AT YOUR
SCOPE?
YES
REPLACE CCFL LAMP

IN THE LCD MODULE
- 15 -

3. NO RASTER (OSD IS NOT DISPLAYED) – MSTAR
NO RASTER
(OSD IS NOT DISPLAYED)
U201 NO CHECK U801 (17", 19")

PIN 18, 90
CHECK U803 (15")
3.3V?
YES
U201 1. CHECK PIN122, 123

PIN96, 97 NO SOLDERING CONDITION
1
OSCILLATE AS 2. CHECK X501
12MHZ? 3. TROUBLE IN U201
YES
2 U501
PIN43 IS 48KHz H-SYNC?
NO CHECK CONNECTION LINE
PIN44 IS 60Hz V-SYNC?
FROM D-SUB TO U501
IS PULSE APPEARED
AT SIGNAL PINS?
AT MODE 12?
YES
TROUBLE IN CABLE
OR LCD MODULE
Waveforms
1 U201-#96, 97 2 U501-#43 H-SYNC 2 U501-#44 V-SYNC
- 16 -

4. TROUBLE IN DPM
TROUBLE IN DPM
CHECK CHECK PC
NO
3 R216, R217 PC IS NOT GOING
R778, R781 INTO DPM OFF MODE
YES
CHECK
U501 PIN 43,44 NO
CHECK H/V SYNC LINE
SYNC PULSE ?
YES
TROUBLE IN U501
Waveforms
3 R216, R778 H-Sync 3 R217, R781 V-Sync
- 17 -

WIRING DIAGRAM
Connector Ass’y P/N:

6631T11012W
or 6631T11020W

6631T20023A

6631T2006H
6631T2006J
- 18 -

100
030
040
080
090
EXPLODED VIEW
070
060
050
020
130
010
120
110
- 19 -

EXPLODED VIEW PARTS LIST
Ref. No. Part No. Description

010 3091TKL148J CABINET ASSEMBLY, L1740BQN BRAND 124A , 8MS
3091TKL148T CABINET ASSEMBLY, L1740BQ BRAND 124A MIRAECHANG NT-C/SKD-CHINA
3091TKL148S CABINET ASSEMBLY, L1740BQ BRAND 124A J-C/SKD-RUSSIA
3091TKL148Z CABINET ASSEMBLY, L1740BQN BRAND 124A ,148J-WA LOCAL-C/SKD-EUROPE
020 6304FLP248A LCD(LIQUID CRYSTAL DISPLAY), LM170E01-A6K7 LG PHILPS TFT COLOR DOT FREE,8MS,LPL KUMI,PB FREE,EGI,SS S D-IC,EGI,250NITS,SXGA,LVDS
or 6304FLP256A LCD(LIQUID CRYSTAL DISPLAY), LM170E01-A6KA LG PHILPS TFT COLOR DOT FREE,8MS,PB FREE,EGI,SS S D-IC,EGI,LPL NJ,250NITS,SXGA,LVDS
or 6304FLP257A LCD(LIQU D CRYSTAL DISPLAY), LM170E01-A6KB LG PH LPS TFT COLOR DOT FREE,8MS,PB FREE,EGI,TI S D-IC,LPL KUMI,SXGA,LVDS
or 6304FLP258A LCD(LIQU D CRYSTAL DISPLAY), LM170E01-A6KC LG PHILPS TFT COLOR DOT FREE,8MS,PB FREE,EGI,TI S D-IC,LPL NJ,SXGA,LVDS
030 3809TKL103B BACK COVER ASSEMBLY, L1740 102A ABS-BK ANALOG
3809TKL103D BACK COVER ASSEMBLY, L1740 102A ABS-BK ANALOG-C/SKD-CHINA,RUSSIA
3809TKL103K BACK COVER ASSEMBLY, L1740BN 102A , 103B - WA LOCAL-C/SKD-EUROPE
040 3043TKK219K TILT SWIVEL ASSEMBLY, L1740 . 219B+LABEL
3043TKK219L TILT SWIVEL ASSEMBLY, L1740 . 219C(B-C/SKD)+LABEL-CHINA,RUSSIA
3043TKK219G TILT SWIVEL ASSEMBLY, L1740 , 219B-WA LOCAL-C/SKD-EUROPE
050 6871TPT282C PWB(PCB) ASSEMBLY,POWER, M-CHASSIS 1720 DOCKING,2PIN,450V POWER TOTAL LIEN CHANG PB FREE
060 3313TL7095A MAIN TOTAL ASSEMBLY, L1740BN F-ENGINE BRAND CL-82
3313TL7095D MAIN TOTAL ASSEMBLY, L1740BN F-ENGINE NT C/SKD 4 LANGUAGE BRAND CL-82-CHINA
3313TL7095C MAIN TOTAL ASSEMBLY, L1740BN F-ENGINE NT C/SKD 10 LANGUAGE BRAND CL-82-RUSSIA
070 4951TKS205F METAL ASSEMBLY, FRAME L1740BN, LPL-AUO
4951TKS205H METAL ASSEMBLY, FRAME L1740BN, F-C/SKD, LPL-AUO
080 4814TKK306A SHIELD, TOP EMI-SHIELD
090 4814TKK306B SHIELD, BOTTOM EMI-SHIELD
100 3551TKK566A COVER ASSEMBLY, L1740 REAR 760A ABS-BK
3551TKK566B COVER ASSEMBLY, L1740 REAR 760A ABS-BK C/SKD
110 4940TKT238A KNOB, TACT CONTROL L1740
120 6871TST955A PWB(PCB) ASSEMBLY,SUB, L1740/1940 CONTROL TOTAL BRAND LF
6871TST955B PWB(PCB) ASSEMBLY,SUB, L1740/1940 CONTROL TOTAL BRAND NT C/SKD LF
130 3551TKK575B COVER ASSEMBLY, L1740 FRONT . LED LENS, IMPROVE
3551TKK575C COVER ASSEMBLY, L1740 FRONT . LED LENS, 575B-WA LOCAL-C/SKD-EUROPE
- 20 -

REPLACEMENT PARTS LIST
CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS,
READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL.
* NOTE : S SAFETY Mark
AL ALTERNATIVE PARTS
DATE: 2005. 03. 15. DATE: 2005. 03. 15.

*S *AL LOC. NO PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
MAIN BOARD
CAPACITORS D702 0DS226009AA KDS226 TP KEC - 80V - - 4NSE
D706 0DS226009AA KDS226 TP KEC - 80V - - 4NSE
C204 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R ZD701 0DZ560009GB "BZT52C5V6S-(F),LF DIODES R/T"
C211 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y ZD711 0DZ560009GB "BZT52C5V6S-(F),LF DIODES R/T"
C213 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y ZD712 0DZ560009GB "BZT52C5V6S-(F),LF DIODES R/T"
C214 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y
C215 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y ICs
C216 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y
C217 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y U201 0IPRPM3017B FE2040-LF(TSU16AWL) MSTAR 10
C218 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y U501 0IZZTSZ641A L1740BN MICOM 44P 10 LANGUAG
C219 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y U501 0IZZTSZ641B L1740BN MICOM 44P 4 LANGUAGE-C/SKD
C220 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y U502 0ICS240813B "CAT24WC08J-TE13 8P,SOIC R/TP"
C221 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y U801 0IPMGKE011A KIA78D33F KEC DPAK R/TP 3.3V
C222 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y Q502 0IKE704200H KIA7042AP TO-92 TP 4 2 VOLT
C223 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y
C224 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y TRANSISTOR
C225 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y
C226 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y Q503 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
C230 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R Q504 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
C231 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R Q505 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
C232 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R Q703 0TR390609FA KST3906-MTF TP SAMSUNG SOT2
C233 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R Q704 0TR390609FA KST3906-MTF TP SAMSUNG SOT2
C240 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R Q801 0TR127309AA KTA1273-Y(KTA966A) TP KEC TO
C251 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y Q802 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
C503 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y Q803 0TR127309AA KTA1273-Y(KTA966A) TP KEC TO
C504 0CH8106F611 10UF 16V M 85STD(CYL) R/TP
C506 0CC030CK01A 3PF 1608 50V 0.25 PF R/TP NP RESISTORs
C507 0CC180CK41A 18PF 1608 50V 5% R/TP NP0
C508 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y R201 0RJ0682D677 68 OHM 1/10 W 5% 1608 R/TP
C701 0CK105CD56A 1UF 1608 10V 10% R/TP X7R R202 0RJ0682D677 68 OHM 1/10 W 5% 1608 R/TP
C707 0CC680CK41A 68PF 1608 50V 5% R/TP NP0 R203 0RJ0682D677 68 OHM 1/10 W 5% 1608 R/TP
C727 0CK105CD56A 1UF 1608 10V 10% R/TP X7R R216 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
C733 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R R220 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
C734 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R R240 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP
C744 0CC680CK41A 68PF 1608 50V 5% R/TP NP0 R503 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
C803 0CE107EF610 "100UF KMG,RD 16V 20% FL BULK" R506 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
C809 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y R520 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
C819 0CK105CD56A 1UF 1608 10V 10% R/TP X7R R523 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R530 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
DIODEs R534 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R535 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
D701 0DS226009AA KDS226 TP KEC - 80V - - 4NSE R537 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
- 21 -

DATE: 2005. 03. 15. DATE: 2005. 03. 15.
*S *AL LOC. NO PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
R543 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP R903 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R544 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP R904 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R545 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TP R905 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP
R547 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TP R908 0RJ7500D677 750 OHM 1/10 W 5% 1608 R/TP
R557 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP U901 0IPRPCR001A "ADA01,LF CHEMTRONICS SOT26,6"
R560 0RJ1501D677 1.5K OHM 1/10 W 5% 1608 R/TP ZD901 0DZ560009GB "BZT52C5V6S-(F),LF DIODES R/T"
R701 0RJ0752D677 75 OHM 1/10 W 5% 1608 R/TP ZD902 0DZ560009GB "BZT52C5V6S-(F),LF DIODES R/T"
R702 0RJ2001D677 2K OHM 1/10 W 5% 1608 R/TP C911 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
R703 0RJ0752D677 75 OHM 1/10 W 5% 1608 R/TP R911 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R704 0RJ2001D677 2K OHM 1/10 W 5% 1608 R/TP R912 0RJ8200D677 820 OHM 1/10 W 5% 1608 R/TP
R706 0RJ0752D677 75 OHM 1/10 W 5% 1608 R/TP R913 0RJ1501D677 1.5K OHM 1/10 W 5% 1608 R/TP
R709 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TP SW911 6600TR1002A SKQGACE010 J-ALPS NON 12V 50
R712 0RJ0102D677 10 OHM 1/10 W 5% 1608 R/TP SW912 6600TR1002A SKQGACE010 J-ALPS NON 12V 50
R716 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP SW913 6600TR1002A SKQGACE010 J-ALPS NON 12V 50
R717 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP SW914 6600TR1002A SKQGACE010 J-ALPS NON 12V 50
R720 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP LED901 0DLBE0168AA BRIGHT LED ELECTRONICS BL-HB
R722 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP LED902 0DLBE0168AA BRIGHT LED ELECTRONICS BL-HB
R723 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP
R724 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TP
R726 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R727 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R737 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R744 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R747 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R751 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TP
R752 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R753 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R754 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R755 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R769 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R778 0RJ0682D677 68 OHM 1/10 W 5% 1608 R/TP
R781 0RJ0682D677 68 OHM 1/10 W 5% 1608 R/TP
R803 0RH0000D622 0 OHM 1 / 10 W 2012 5 00% D
R804 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R805 0RH2000D622 200 OHM 1 / 10 W 5% D R/TP
R806 0RH2000D622 200 OHM 1 / 10 W 5% D R/TP
R808 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R816 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R820 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R821 0RH0000D622 0 OHM 1 / 10 W 2012 5 00% D
R824 0RJ0272D677 27 OHM 1/10 W 5% 1608 R/TP
R825 0RJ2000D677 200 OHM 1/10 W 5% 1608 R/TP
OTHERs
X501 6212AA2004A HC-49U TXC 12 0MHZ +/- 30 PP
CONTROL BOARD
C901 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0

C905 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C906 0CK105CD56A 1UF 1608 10V 10% R/TP X7R
Q1 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
Q2 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP
R901 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R902 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP
- 22 -

SCHEMATIC DIAGRAM
1. FE2030 / FE2040
1
U201-#96, 97
Waveforms
3
3
R216, R778 H-Sync
/ FE2040
FE2030
U201
1
3
R217, R781 V-Sync
- 23 -

2. MICOM
2
U501-#43 H-SYNC
Waveforms
2
U501-#44 V-SYNC
U501
MTV41 2PL CC
- 24 -

3. POWER
- 25 -

4. CONNECTOR & JACKS
- 26 -

Mar. 2005
P/NO : 3828TSL094M Printed in Korea

LG Flatron l1740 l1940 Service Manual

Uploaded by

Copyright:

Available Formats

LG Flatron l1740 l1940 Service Manual

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LG Flatron l1740 l1940 Service Manual

Uploaded by

Copyright:

Available Formats

Website:http://biz.LGservice.

*To apply the MSTAR Chip.

Downloaded from www.Manualslib.com manuals search engine

2. OPTICAL CHARACTERISTICS STAND-BY OFF/ON OFF less than 1 W AMBER

Downloaded from www.Manualslib.com manuals search engine

TAKE CARE DURING HANDLING THE LCD MODULE AC Volt-meter

• Do not scratch or press on the panel with any sharp

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Dot Total Display Front Sync. Back

Downloaded from www.Manualslib.com manuals search engine

Disassembly Hinge Cover. Remove the screws.

Disassemble back cover. Disassemble inverter shield something thin.

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

1. Video Controller Part.

Downloaded from www.Manualslib.com manuals search engine

PWM PHOTO- SIGNAL

2. Input rectifier and filter.

4. Output rectifier and filter.

Downloaded from www.Manualslib.com manuals search engine

2) Edit Week of Manufacture, Year of Manufacture,

c) Remove all default number

e) Click Start button.

Downloaded from www.Manualslib.com manuals search engine

Power inlet (required)

Power Select Switch

Figure 1. Cable Connection

Downloaded from www.Manualslib.com manuals search engine

CHECK POWER BOARD,

CHECK KEY CONTROL

CHECK U201 PIN 96 NO

Downloaded from www.Manualslib.com manuals search engine

CHECK POWER BOARD,

J705 PIN9 NO CHECK MICOM INV

REPLACE CCFL LAMP

Downloaded from www.Manualslib.com manuals search engine

U201 NO CHECK U801 (17", 19")

U201 1. CHECK PIN122, 123

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Connector Ass’y P/N:

Connector Ass’y P/N:

Connector Ass’y P/N:

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Ref. No. Part No. Description

Downloaded from www.Manualslib.com manuals search engine

DATE: 2005. 03. 15. DATE: 2005. 03. 15.

Downloaded from www.Manualslib.com manuals search engine

X501 6212AA2004A HC-49U TXC 12 0MHZ +/- 30 PP

C901 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine