OPERATORS MANUAL

3.0 GS, 4.3 GL/Gi, 5.0 GL/Gi, 5.7 GS/GSi,

7.4 Gi/GSi, 8.2 GSi, DPX 385/415

1
2
 PRODUCT AND APPLICATION INFORMATION

Please complete this section for future reference.

Delivery date ____________________________________________________________________________

Engine model number _____________________________________________________________________

Engine serial number _____________________________________________________________________

Drive/Transmission model __________________________________________________________________

Drive/Transmission serial number ____________________________________________________________

Transom shield assembly serial number _______________________________________________________

Boat manufacturer _______________________ Boat year ________________________________________

Boat model ____________________________ Boat length ______________________________________

Hull ID number (HIN) ______________________________________________________________________

State/Province registration number ___________________________________________________________

Propeller size ____________________________________________________________________________

Selling dealer ____________________________________________________________________________

______________________________________________________________________________________

______________________________________________________________________________________

Servicing dealer __________________________________________________________________________

______________________________________________________________________________________

______________________________________________________________________________________
It is very important that you obtain all serial numbers directly from serial number plates attached to product assem-
blies. Check page 17 for the location of product serial number plates.

1999, Volvo Penta of the Americas, Inc. Volvo, Volvo Penta, DP Duoprop, and (Aquamatic) are of AB Volvo. DPX and QL are of AB Volvo Penta. DuraPlus,
2PLUS4, Speed Rails, and Xact are trademarks of Volvo Penta of the Americas, Inc. SX Cobra and SX Diesel are trademarks of Volvo Penta Marine Products, L.P.

Volvo Penta reserves the right, without prior notice, to revise materials, standard equipment, specifications, models and to discontinue models. Not all models,
equipment and accessories are available in all markets or countries. Certain models and/or configurations may not be available at the time of publication.
Representations made regarding these products are subject to actual use, application, and/or operating conditions, as well as proper maintenance. The
power rating data contained herein is for engines and conditions as tested and may vary within manufacturing tolerances. Engines pictured in this brochure may
feature custom accessories that are not necessarily standard on production models. Horsepower ratings are in accordance with NMMA procedure.

3
4
 CONTENTS

CONTENTS ................................................................................................................................................................... 5
INTRODUCTION ............................................................................................................................................................ 9
Our core values: Quality, Safety, Environmental Care .............................................................................................. 9
Factors that affect engine performance .................................................................................................................. 10
Power ratings ................................................................................................................................................... 10
How load conditions affect the speed of a planing hull ..................................................................................... 10
Wagon-back effect ........................................................................................................................................ 10
Your new boat ........................................................................................................................................................ 11
Boaters responsibilities ......................................................................................................................................... 11
Planning your trip ............................................................................................................................................. 11
Safety equipment ............................................................................................................................................. 11
Basic safety rules of boating ............................................................................................................................ 11
SAFETY ....................................................................................................................................................................... 13
GENERAL INFORMATION .......................................................................................................................................... 17
Identification numbers ............................................................................................................................................ 17
Owners identification card ............................................................................................................................... 17
Product references, illustrations, and specifications ............................................................................................... 17
Volvo Action Service (VAS)..................................................................................................................................... 17
Doing your own maintenance and repairs .............................................................................................................. 18
Parts and accessories ............................................................................................................................................ 18
Volvo Penta dealer network .................................................................................................................................... 18
Warranty information .............................................................................................................................................. 18
2 PLUS 4 Extended Protection ........................................................................................................................... 19
FEATURES .................................................................................................................................................................. 21
Anodes (sacrificial) .............................................................................................................................................. 32
Audible alarm ......................................................................................................................................................... 32
Engine systems ...................................................................................................................................................... 32
Cooling system ................................................................................................................................................ 32
Fuel system ..................................................................................................................................................... 32
Exhaust system ............................................................................................................................................... 33
Electrical system .............................................................................................................................................. 33
Lubrication system ........................................................................................................................................... 33
Steering system ............................................................................................................................................... 33
Drive components .................................................................................................................................................. 33
Emergency stop switch .......................................................................................................................................... 33
Engine protection mode (EFI systems) .................................................................................................................. 34
Instruments ............................................................................................................................................................ 34
Engine instruments .......................................................................................................................................... 34
Trim instruments .............................................................................................................................................. 35
Trim/tilt motor protection .................................................................................................................................. 36
Impact protection ............................................................................................................................................. 36
Power trim/tilt ......................................................................................................................................................... 36
Propellers ............................................................................................................................................................... 37
Drive unit, rotation, and propellers ................................................................................................................... 38
Trim controls .................................................................................................................................................... 40

5
 Operating trim controls .................................................................................................................................... 40
Remote diagnostic uplink system ........................................................................................................................... 41
Setting up the diagnostic uplink system cell phone .......................................................................................... 41
Using the remote diagnostic uplink system ...................................................................................................... 41
OPERATION ................................................................................................................................................................ 43
Engine break-in period ........................................................................................................................................... 43
Operating after break-in period .............................................................................................................................. 45
Before starting ........................................................................................................................................................ 45
Starting the engine, cold start ................................................................................................................................. 46
Starting the engine (warm start) ............................................................................................................................. 47
Stopping the engine ............................................................................................................................................... 47
Operating remote controls ...................................................................................................................................... 48
Side mount control ........................................................................................................................................... 48
Top mount control ............................................................................................................................................ 48
Steering system operation ...................................................................................................................................... 48
Twin unit steering ............................................................................................................................................. 48
Power trim and tilt operation ................................................................................................................................... 49
Power trim operation ........................................................................................................................................ 49
Determining the proper trim ............................................................................................................................. 49
Operating in bow-up position ......................................................................................................................... 49
Operating in bow-down position .................................................................................................................... 49
Power tilt operation .......................................................................................................................................... 50
Power trim/tilt switch operation ........................................................................................................................ 50
Power trim/tilt switch and gauge location ......................................................................................................... 51
Shifting and controlling speed ................................................................................................................................ 51
Checking instruments ............................................................................................................................................. 52
Special boating circumstances ............................................................................................................................... 52
Engine protection mode operation (fuel injection systems) .............................................................................. 52
Shallow water operation ................................................................................................................................... 52
High altitude operation ..................................................................................................................................... 52
Operating procedure for freezing temperatures ............................................................................................... 53
Salt water operation ......................................................................................................................................... 53
Twin unit operation ........................................................................................................................................... 53
Trailering your boat ................................................................................................................................................ 53
Propeller selection .................................................................................................................................................. 53
MAINTENANCE ........................................................................................................................................................... 55
Maintenance schedule ........................................................................................................................................... 55
Preparing for boating after storage (summerization) ............................................................................................ 57
Off-season storage preparations (winterization) ................................................................................................... 57
Exhaust system ...................................................................................................................................................... 57
Engine exhaust system .................................................................................................................................... 57
Drive unit bellows ............................................................................................................................................. 58
Fuel system ............................................................................................................................................................ 58
Gasoline recommendations ............................................................................................................................. 58
Gasoline containing alcohol ............................................................................................................................. 58
Detonation (spark knock) ................................................................................................................................. 59
Preventing gum formation and corrosion in the fuel system ............................................................................. 59
Carburetor (GL, GS only) ................................................................................................................................. 59
Electronic fuel injection (Gi, GSi only) .............................................................................................................. 59
Flame arrestor ................................................................................................................................................. 60
Electric fuel pumps .......................................................................................................................................... 60
Fuel filter .......................................................................................................................................................... 60
6
 Engine fuel filter replacement .......................................................................................................................... 60
Carburetor fuel filter replacement .................................................................................................................... 61
Electrical system .................................................................................................................................................... 61
Battery cables .................................................................................................................................................. 62
Batteries and connections ............................................................................................................................... 62
Engine start battery .......................................................................................................................................... 64
Multiple batteries and selector switch .............................................................................................................. 65
Distributor cap and rotor .................................................................................................................................. 65
Circuit breakers and fuses ............................................................................................................................... 65
Spark plugs ...................................................................................................................................................... 65
Checking and changing spark plugs ................................................................................................................ 66
Belt adjustments .............................................................................................................................................. 67
Belt tension ...................................................................................................................................................... 67
Alternator belt .................................................................................................................................................. 68
Idler belt ........................................................................................................................................................... 68
Cooling system ...................................................................................................................................................... 68
Draining the cooling system ............................................................................................................................. 69
Engine raw water cooled ............................................................................................................................ 69
Engine fresh water cooled (if equipped) ...................................................................................................... 69
Raw water pump .............................................................................................................................................. 70
Oil cooler ......................................................................................................................................................... 70
Steering system ..................................................................................................................................................... 70
Power trim/tilt fluid level ................................................................................................................................... 70
Steering reservoir fluid level ............................................................................................................................. 70
Primary shaft spline and bearing lubrication .................................................................................................... 71
Tie rod (twin installations only) ......................................................................................................................... 71
Engine and drive service ........................................................................................................................................ 71
Lubrication system ................................................................................................................................................. 71
Engine/crankcase oil ........................................................................................................................................ 71
Checking engine oil level ................................................................................................................................. 72
Changing engine oil ......................................................................................................................................... 72
Changing the oil filter ....................................................................................................................................... 73
Drive components .................................................................................................................................................. 73
Drive unit lubrication ........................................................................................................................................ 73
External lubrication points ................................................................................................................................ 76
Anodes (sacrificial anodes) ........................................................................................................................... 76
Active corrosion protection system .................................................................................................................. 77
Propeller care ......................................................................................................................................................... 77
Propeller replacement SX ........................................................................................................................... 78
Propeller replacement DP-S ........................................................................................................................ 79
Propeller replacement DPX ......................................................................................................................... 80
Boat bottom ............................................................................................................................................................ 80
Engine alignment ................................................................................................................................................... 80
Replacement parts ................................................................................................................................................. 81
Bottom painting ...................................................................................................................................................... 81
Engine submersion ................................................................................................................................................ 82
PROBLEM RESOLUTION ............................................................................................................................................ 85
SPECIFICATIONS ........................................................................................................................................................ 87
3.0 GS .................................................................................................................................................................... 87
4.3 GL/Gi ................................................................................................................................................................ 88
5.0 GL/Gi ................................................................................................................................................................ 89
5.7 GS/GSi ............................................................................................................................................................. 90

7
 7.4 Gi/GSi; 8.2 GSi ................................................................................................................................................ 91
DPX 385; DPX 415 .................................................................................................................................................. 92
APPENDIX A: CERTIFIED ENGINES AND BSO NUMBERS ........................................................................................ 93
Certified engines ..................................................................................................................................................... 93
Bodensee Shiffahrts Ordnung (BSO) number .......................................................................................................... 93

8
 INTRODUCTION

Congratulations on choosing a new boat equipped with a Volvo Penta marine engine. Volvo Penta
has been building marine engines since 1907. Quality, operating reliability, and innovation have
made Volvo Penta a world leader in the marine engine industry. From engineering design and
manufacturing to support activities in Parts, Service, and Sales, high standards have been set to
ensure your pride and satisfaction as the owner of a Volvo Penta product.
As owner of a Volvo Penta marine engine, we would also like to welcome you to a worldwide
network of dealers and service workshops to assist you with technical advice, service require-
ments and replacement parts. Please contact your nearest authorized Volvo Penta dealer for
assistance.
We wish you many pleasant voyages.
Our core values: Quality, Safety, Environmental Care ______________________________
The values and qualities that Volvo Penta expresses are what make the company unique. From the very beginning,
safety and quality have stood at the heart of the development of all of our products, processes, and services. It is on
these values and qualities that the Volvo Penta corporate identity, brand position and legal status have been founded.
Todays core values of quality, safety, and care for the environment remain central to Volvo Penta. They express what
we believe in as a company and will ultimately help us to survive.
Quality is a value that traditionally referred to product quality but now encompasses all aspects of our products and
services. In todays competitive environment, Volvo Pentas quality commitment extends beyond industrial craftsman-
ship and engineering ingenuity to embrace care for the customer throughout the life of the product.
Safety will always be our most distinguishing core value. Historically embedded in the quality of all Volvo products, it
also encompasses personal, family, business, and environmental values.
Environmental care in all operations, from design to production, distribution, service, and recycling, is an integral part
of the Volvo quality commitment towards customers, employees, and the community. By embracing the environment
as a core value, Volvo demonstrates its understanding of the environmental impact its products have upon nature and
the shared urban and rural surroundings.
Volvo Penta continually commits a considerable part of its development resources toward minimizing the environmen-
tal impact of its products. Examples of areas where we are always looking for improvements are exhaust emissions,
noise levels, and fuel consumption.
Regardless of whether your Volvo Penta engine is installed in a boat used for pleasure or commercial operation,
incorrect operation or improper maintenance of the engine will result in disturbance or damage to the environment.
In this owners manual there are a number of service procedures, which, if not followed, will lead to an increase in the
engines impact on the environment, and on running costs and a reduction in service life. Always observe recom-
mended service intervals and make a habit of checking that the engine is operating normally every time you use it.
Contact an authorized Volvo Penta dealer if you cannot correct the fault yourself.
Remember that most chemicals used on boats are harmful to the environment if used incorrectly. Volvo Penta recom-
mends the use of biodegradable degreasing agents for all cleaning. Always dispose of engine and transmission oil
waste, old paint, degreasing agents and cleaning residue etc. at proper disposal areas so that they do not harm the
environment.
Adapt speed and distance during your boat trips so that swell and noise generated by the boat do not disturb or harm
wildlife, moored boats, docks, etc. Wherever you land or cruise, please show consideration and always leave the areas
you visit as you would like to find them yourself.
9
Factors that affect engine performance __________________________________________
Power ratings
A great number of environmental factors, such as barometric pressure, ambient temperature, humidity, the quality of
fuel, and exhaust back pressure can affect engine performance. When it comes to quoting and comparing ratings, it is
important that there is a unified set of standards for measurement.
In September 1989, all major marine engine manufacturers agreed to quote engine power output according to a
common set of conditions. These conditions are referred to as ISO 8665. All Volvo Penta engines meet the ISO 8665
standard. This ISO standard outlines the following fixed values or common conditions for determining the rating of the
engine.

Condition Va lue Condition Va lue

Sea water temperature 77 F (25 C) Exhaust back pressure 1.45 PSI (10 kPa)
Fuel temperature 104 (40 C) Barometric pressure 14.504 PSI (100 kPa)
Air temperature 77 F (25 C) Relative humidity 30%

A gasoline engine operates with very little surplus air. When conditions deviate from the standard values, the result can
be a loss of power at full load. It can also cause a rise in exhaust emissions due to incomplete fuel combustion.
Marine engines can be rated according to one of several power standards, but power output itself is quoted in kilowatts
(KW) or horsepower (HP), for a given engine speed, usually at maximum revolutions per minute (RPM).
How load conditions affect the speed of a planing hull
The overall weight of the boat is another important factor in performance. Any increase in boat weight will slow down
the boat speed, particularly on boats with planing and semiplaning hulls.
For example, a new boat tested with fuel and water tanks only half filled, and without any load, can easily drop 2 to 3
knots in speed when tested fully fuelled and loaded with all normal equipment and supplies for safe and comfortable
cruising. This is because the propeller installed originally is frequently one that is designed to give maximum speed
when the boat is new. For this reason it is often advisable to reduce the propeller pitch by as much as an inch or more
in order to counter the effects of the increase in overall weight encountered in normal cruising, particularly in hotter
climates. Although this will reduce top speed somewhat, overall ride conditions will improve and you should achieve
greatly enhanced acceleration.
In considering the influence of weight, it is worth remembering that fiberglass boats absorb a significant amount of
water into their hulls while left afloat for any length of time and so become progressively heavier. Another negative
influence on boat performance is marine growth beneath the waterline - a problem that is often overlooked.
Wagon-back effect
As long as we continue to use combustion technology for engines,
there will be exhaust emissions. Despite the substantial reductions
achieved in modern engines, as fuel burns exhaust emissions and
fumes will always be given off.
But there is also another effect. Any shear-bodied object moving
forward will create a phenomenon we call wagon-back effect. Due
to a difference in air pressure, the airflow behind such an object will have a tendency to draw dirt and exhaust emis-
sions back into the object. (Youll frequently see evidence of this in the excess of road grime that is drawn back onto
the rear windows of cars.) A boat with a sheer, broad transom and high superstructure creates its own wagon-back
effect. This recirculating air has a tendency to draw exhaust fumes and water spray up toward the afterdeck. Often
people will make the mistake of opening a ventilator or port hole in order to remove the fumes, but it has the opposite
effect more fumes are drawn in, and conditions merely become worse. In high concentrations these fumes may be
hazardous. If you suspect that your boat exhibits this wagon-back effect. please contact your Volvo Penta dealer.

10
Your new boat _______________________________________________________________
Every new boat has its own special characteristics. Even experienced boat owners should note carefully how a boat
behaves at different speeds, weather conditions, and loads. Your boat owners manual contains information to help you
operate it with safety and pleasure. It contains details of the boat, equipment supplied or fitted, systems, and informa-
tion on operation and maintenance. Please read it carefully, and familiarize yourself with your boat before using it for
the first time.
We strongly recommend that you install an emergency stop switch (see page 33), regardless of the type of boat. If your
boat does not have with an emergency stop switch, contact your Volvo Penta dealer, who can assist you in selecting
one.

Boaters responsibilities ______________________________________________________

The operation, maintenance, and care of the Volvo Penta engine and power package as outlined in the owners
manual are the owners responsibility. (See the Maintenance Schedule on page 55.) The owner must keep records of
all maintenance services performed. This record of proper maintenance may be required to determine warranty
coverage on certain repairs and should be transferred to each subsequent owner. If you are not sure of the proper
maintenance procedures, contact the Volvo Penta Consumer Affairs Department at the address on page 85 of this
document.
The operator is responsible for the correct operation of the boat and for the safety of all passengers. Make sure that all
operators read this manual before operating the boat. Show your passengers the location of emergency equipment
and explain how to use it. Be sure one of your passengers knows how to handle your boat in case of emergency.
Requirements for personal flotation devices (life vests, life preservers) and other safety equipment vary, depending on
the type of boat and local regulations. Always comply with the regulations that apply to your boat.
Planning your trip
Everyone wants to have a problem-free and pleasant time when they take their boat out. To help you do this we have
provided a pre-journey checklist below. Take extra time to check the engine and its equipment and the general mainte-
nance of the boat.
Get up to date charts for the planned route
Calculate distance and fuel consumption
Note places where you can refuel on your planned course
Tell friends or relatives about your route (that is, file a float plan).
Safety equipment
Rescue and emergency items such personal flotation devices and signal rockets. Make sure all passengers know
where these items are.
Replacement parts
Proper tools
Fire extinguisher checked and charged
Basic safety rules of boating
Shut off the engine when people who are in the water come near the boat.
Propellers are inherently dangerous, and as such are potential safety hazards. Make sure that the propeller is not
operating when people who are in the water come near the boat.
Avoid standing up or shifting weight suddenly in small, lightweight boats.
Keep your passengers seated in seats. The boats bow, gunwale, transom, and seat backs are not intended for
use as seats.

11
 Insist on the use of personal flotation devices by all passengers at all times.
Know the rules of the road and obey them. If you are not familiar with the rules of the road, take the
U.S. Coast Guards boater safety course. You may find information about boating safety at
WWW.USCGBOATING.ORG and WWW.CGAUX.ORG/CGAUXWEB/PUBLIC/PUBFRAME.HTM.
Prevent explosion and fire by maintaining your fuel delivery system in top condition. Fuel vapor is
volatile; handle fuel with care.
Keep your boat and equipment neat and in top operating condition. Carry a selection of spare parts for
the engine. (Volvo Pentas on-board kit contains a selection of essential items that a boat owner
should carry at all times. See your Volvo Penta dealer.)
NEVER OPERATE THE BOAT IF YOU ARE UNDER THE INFLUENCE OF DRUGS OR ALCOHOL.
If boating waters are unfamiliar, obtain appropriate charts to avoid damage from underwater objects.

12
 SAFETY

This owners manual contains information you need to operate your boat engine and drive safely. Check that you have
the correct manual for your engine and drive.
This manual also contains a considerable amount of information concerning the engine and drive: model identification,
preventive maintenance recommendations, fuel and oil recommendations, and other important points. Please keep this
book with your boat at all times.
Note: It is important that this manual stays with the boat when it is sold. Important safety information must be passed
to the new owner. The service information provided in the manual gives the owner important information about main-
taining the engine and drive.
If you do not understand or are uncertain about any operation or information in this owners manual, please contact
your Volvo Penta dealer. He will be able to help you with an explanation or will demonstrate the operation.
Note: Federal law requires manufacturers to notify owners in the event that a safety related defect is discovered on
any of their products. If you are not the original owner of this engine and drive, please notify us at our address listed on
page 85, or through an authorized Volvo Penta dealer about the change in ownership. This is the only way we will be
able to contact you if necessary.
This manual will alert you to certain things you should do very carefully. If you dont, you could
hurt yourself or bystanders
hurt the boat operator or bystanders
damage the machinery.
Carefully observe the safety alert symbols shown for dangers, warnings, and cautions. They warn you of possible
dangers or important information contained in this manual.
HOWEVER: Warnings alone do not eliminate hazards, nor are they a substitute for safe
boat handling and proper accident prevention measures!

Failure to comply with a danger symbol will result in serious injury or death to boat opera-
tor, boat occupants, and/or others.

Failure to comply with a warning may result in injury or death to boat operator, boat occu-
pants and/or others.

Failure to comply with a caution may result in failure or damage to the equipment.

13
 Below is a summary of the risks and safety precautions you should always observe or carry out when
operating or servicing the engine:
1. Check that the warning or information decals on the engine are always clearly visible. Replace decals
that have been damaged or painted over.
2. Always turn the engine off before starting service procedures. Avoid hot surfaces and liquids in supply
lines and hoses when the engine has just been turned off and is still hot.
3. To prevent a possible explosion, operate the blower as recommended by the boat manufacturer
before starting the engine. If the engine compartment is not equipped with a blower, open the engine
cover or hatch before starting to disperse any gasoline fumes that may be present. Leave the hatch
open until after the engine is running.
4. Reinstall all protective parts removed during service operations before starting the engine. Make a
point of familiarizing yourself with other risk factors, such as rotating parts and hot surfaces (exhaust
manifold, starter, etc.).
5. Approaching a running engine is dangerous. Loose clothing or long hair can get caught in rotating
parts and cause serious personal injury.
6. If so equipped, turn off the power supply to the engine at the main switch and lock it in the OFF
position before starting work.
7. Avoid opening the filler cap for engine coolant system (freshwater cooled engines) when the engine is
still hot. Steam or hot coolant can spray out as system pressure is lost.
8. If opening the filler cap or drain cock/venting cock, or removing a plug or engine coolant line from a
hot engine, open the filler cap slowly and release coolant system pressure gradually; otherwise,
steam or hot coolant can spray out.
9. Stop the engine and close or block the sea water intake before carrying out operations on the engine
cooling system.
10. Only start the engine in a well-ventilated area. If operating the engine in an enclosed space, make
sure your work area is well ventilated.
11. Anticorrosion and antifreeze agents can be hazardous to health and to the environment. Whenever
you use these agents, follow the manufacturers instructions on the product packaging.
12. Certain engine oils are flammable. Some of them are also dangerous if inhaled. Whenever you use
these agents, follow the manufacturers instructions on the product packaging. Ensure that ventilation
in the work place is good. Use a protective mask when spraying.
13. Hot oil can cause burns. Avoid skin contact with hot oil. Ensure that the lubrication system is not
under pressure before beginning to work on it. Never start or operate the engine with the oil filler cap
removed; otherwise, hot oil could spew out.
14. Never allow an open flame or electric sparks near the battery or batteries. Never smoke in proximity
to the batteries. The batteries give off hydrogen gas during charging which when mixed with air can
form an explosive gas. This gas is easily ignited and highly volatile. Incorrect connection of the battery
can cause a spark, which would be sufficient to cause an explosion. Do not disturb battery connec-
tions when starting the engine (spark risk) and do not lean over batteries.
15. Always ensure that the positive and negative battery leads are correctly installed on the correspond-
ing terminal posts. Incorrect installation can result in serious damage to electrical equipment.
16. Always use protective goggles when charging and handling batteries. Battery electrolyte contains
sulfuric acid, which is highly corrosive. If battery electrolyte comes into contact with unprotected skin,
wash it off immediately using plenty of water and soap. If battery acid comes in contact with the eyes,
14
 immediately flush with copious amounts of water and obtain medical assistance.
17. To ensure safe handling and to avoid damaging engine components on top of the engine, use a lifting
beam to raise the engine. All chains and cables should run parallel to each other and as perpendicu-
lar as possible in relation to the top of the engine. Always check that lifting equipment is in good
condition and has sufficient load capacity to lift the engine and any extra equipment installed.
18. If extra equipment is installed on the engine, which alters its center of gravity, a special lifting device is
required to achieve the correct balance for safe handling.
19. Never work on an engine that is suspended on a hoist.
20. Components in the electrical, ignition, and fuel systems on Volvo Penta products are designed and
constructed to minimize the risk of fire and explosion. Using non-original Volvo Penta parts that do
not meet the above standards can result in fire or explosion on board. Damage caused by using
non-original Volvo Penta replacement parts will not be covered under any warranty provided by Volvo
Penta.
21. Fuel filter replacement should be carried out on a cold engine to avoid the risk of fire caused by fuel
spilling onto the exhaust manifold. Always cover the generator if it is located under the fuel filter. The
generator can be damaged by spilled fuel.
22. Always use protective gloves when tracing leaks. Liquids ejected under pressure can penetrate body
tissue and cause serious injury.
23. Always use fuel recommended by Volvo Penta. The use of lower quality fuels can damage the
engine. Poor fuel quality can also lead to higher maintenance costs.
24. Never use a high-pressure washer when washing the engine.

15
16
 GENERAL INFORMATION

Identification numbers ________________________________________________________

Immediately upon taking delivery of your new boat, have the dealer record the
model and serial numbers of the engine and drive in the Product and Application
Information space provided on the inside front cover. (These numbers are
required for warranty registration, warranty service, and ordering parts.) Include
the model and serial number of your boat and any auxiliary equipment. Also,
make a copy and keep the copy in a safe place in the event your boat is stolen.
Owners identification card
When you purchased your boat, the dealer was required to complete a warranty
and registration form for your Volvo Penta product. The owners portion of this
Engine model number form is your Owners Identification Card. This card provides proof of ownership
and is required to validate warranty, should warranty service be necessary.
Warranty coverage may be delayed until the warranty and registration form is on
file at Volvo Penta.

Product references, illustrations, and specifications ______

All information, illustrations and specifications contained in this manual are
based on the latest product information available at the time of printing. Volvo
Penta of the Americas, Inc. reserves the right to make changes at any time,
without notice, in specifications and models; to discontinue models; to change
any specifications or parts at any time without incurring any obligation to equip
same on models manufactured prior to date of such change.
Transom shield model number When reference is made in this manual to a brand name, number, product or
specific tool, an equivalent product may be used in place of the product referred
to unless specifically stated otherwise. To avoid hazards, equivalent products
used must meet all current U.S. Coast Guard Safety Regulations and American
Boat and Yacht Council (ABYC) standards.
All illustrations used in this manual may not depict actual models or equipment
and are intended as representative views for reference only.
The continuing accuracy of this manual cannot be guaranteed.

Volvo Action Service (VAS) ___________________________

Volvo Action Service (VAS) is a consumer break-
Drive unit model number down service available 24 hours each day, 365
days per year. If your engine breaks down, the VAS
coordinator will quickly locate your nearest dealer.
If you need a tow, parts, or mechanic, the VAS coordinator will make all arrangements
necessary to get you back underway as soon as possible. Membership to Volvo Action
Service is provided automatically to all Volvo Penta engine owners. As long as your Volvo
Penta engine is under factory warranty, this service is absolutely free for Volvo Penta-related repairs. Towing is not
covered by the Volvo Penta warranty. Once your warranty period has expired, there is a charge of $50.00* U.S. per
managed breakdown, plus any additional costs incurred for towing, parts, or repairs.
If you have a question about Volvo Action Service, or need additional information, call toll-free 1-877-33-PENTA.

*
Price subject to change without notice.
17
Doing your own maintenance and repairs ________________________________________
If you plan to do your own maintenance and repairs on your Volvo Penta products, you should purchase a set of
service manuals that pertain to your particular engine and drive. Keep in mind, however, that there are certain tasks
that should only be performed by your Volvo Penta dealer. He has the tools, expertise, and most current information
needed to properly perform these tasks.
Dealer-only maintenance items are listed in the Maintenance Schedule, page 55.

Parts and accessories ________________________________________________________

Genuine Volvo Penta parts are the result of many hours of strenuous testing, and fulfill
Volvo Pentas strict quality and safety requirements. Your authorized dealer has a
complete line of (or may order) genuine Volvo Penta parts, accessories, coolants, and
lubricants. When replacements are required, use only Volvo Penta genuine parts.
Purchase all Volvo Penta replacement parts, accessories, coolants, and lubricants from
an authorized Volvo Penta dealer. He has needed parts in stock for routine mainte-
nance, as well as the information needed to order special parts and accessories for
you.
Only authorized Volvo Penta dealers may purchase genuine parts and accessories
directly from the factory. Volvo Penta does not sell to unauthorized dealers or retail
customers.

Volvo Penta dealer network

Toll-free Dealer Locator
Volvo Penta has a comprehensive dealer network that offers both service and Service
spare parts for Volvo Penta engines. These dealers have been carefully selected
and trained to provide professional assistance for service and repairs. They also If you are away from your
have the special tools and testing equipment required for maintaining a high home waters, take your Volvo
standard of service. Volvo Penta dealers and vendors must maintain a stock of Penta product to the nearest
original spare parts and accessories to cover most requirements of Volvo Penta Volvo Penta servicing dealer.
owners. When ordering a service or spare parts always quote the engine and drive/ To locate a Volvo Penta
reverse gear complete type designation and serial number. You will find this infor- servicing dealer, check the
mation on the engine product plate and on a decal on the valve cover. Yellow Pages under Boat
Always take your Volvo Penta product to an authorized Volvo Penta servicing dealer Dealers, or call 1-800-522-
for repair. Our dealers have the knowledge, factory-trained technicians, and special 1959.
tools to take care of any necessary repairs. Ideally, take your product back to your
selling dealer he also knows you and your equipment.
For the name and location of your nearest Volvo Penta dealer, consult the Yellow Pages under Boat Dealers, or call
1-800-522-1959.
Volvo Penta on the Internet ____________________________________________________
The URL address for Volvo Penta of the Americas is http://www.volvo.com. When you reach the Volvo home page,
choose the Marine and Industrial Engines icon.

Warranty information _________________________________________________________

Volvo Pentas warranty package can be found on page 87. Along with the warranty information you will find other
checklists and reports for Volvo Penta products.
Some areas may have other warranty conditions, depending on national legislation and regulations. Information about
these conditions can be obtained from Volvo Penta importers and dealers in those areas. Contact your local Volvo
Penta representative for a copy.

18
Warranty Registration Form
The Warranty Registration Form should always be filled out and sent in by the dealer. Make sure that this has been
done, since delay of warranty claims can occur if no proof of the delivery date can be provided.

2 PLUS 4 Extended Protection ________________________________________________

In addition to our factory warranty, owners may purchase Volvo Pentas exclusive 2 PLUS
4 Extended Protection plan, which provides additional service benefits for a total of six
years of coverage. The 2 PLUS 4 program covers most repairs to Volvo Penta engines,
drives, and transmissions, and is fully transferable to second owners.
The extended protection plan provides mechanical coverage, a towing allowance, and
optional accessories and trailer coverage. It covers an extensive list of repairs with only a
$25.00 deductible per repair visit. See Appendix B of this document for more information
about the 2 PLUS 4 Extended Protection plan, or call 1-800-235-7549.

19
20
 FEATURES

Your Volvo Penta product consists of two components: the engine and the drive. There are certain parts on each
component that you, the owner, must take care of to make sure that your Volvo Penta product stays in optimum
running condition. The important parts of each component are shown in the photographs on pages 22 through 31.
Explanations of these parts and systems are described below; the maintenance procedures are found in the Mainte-
nance section starting on page 55.

21
 3.0 GS Alarm and Fuse Detail

3.0 GS (front view)

22
3.0 GS (starboard view)

3.0 GS (port view)

23
 Fuses and circuit Fuses and circuit
breakers breakers
(port view) (starboard view)

4.3 GL, 5.0 GL, 5.7 GS (front view)

24
4.3 GL, 5.0 GL, 5.7 GS (starboard view)

4.3 GL, 5.0 GL, 5.7 GS (port view)

25
 Fuses and circuit
breakers
(starboard view) Fuses and circuit
breakers
(port view)

4.3 Gi, 5.0 Gi, 5.7 GSi (front view)

26
4.3 Gi, 5.0 Gi, 5.7 GSi (starboard view)

4.3 Gi, 5.0 Gi, 5.7 GSi (port view)

27
 Fuses and circuit
breakers
(starboard view) Fuses and circuit
breakers
(port view)

7.4 Gi, 7.4 GSi, 8.2 GSi (front view)

28
7.4 Gi, 7.4 GSi, 8.2 GSi (starboard view)

7.4 Gi, 7.4 GSi, 8.2 GSi (port view)

29
 Fuses and circuit
breakers
(starboard view) Fuses and circuit
breakers
(port view)

DPX 385, 415 (front view)

30
DPX 385, 415 (starboard view)

DPX 385, 415 (port view)

31
Anodes (sacrificial) _________________________________________________________
Electrochemical corrosion of metal can cause very serious and expensive damage to drives,
propellers, propeller shafts, rudders, keels, and other equipment fitted to your boat. To protect your
investment, Volvo Penta sterndrive units are equipped with zinc anodes to provide protection
against galvanic (electrochemical) corrosion. These anodes are sacrificial, or designed to erode
away faster than the metal on the transom shield and sterndrive. (For sterndrives used only in fresh
water a magnesium anode should be used.)
Use only genuine Volvo Penta zinc and magnesium anodes. Some aftermarket anodes may not meet mil-specs
and are larger in size. Using aftermarket sterndrive anodes may cause cavitation bubbles due to poor fit, which may
lead to propeller erosion. When you must replace the anodes, see your Volvo Penta dealer, since if additional elec-
tronic or electrical equipment is installed, each must have an individual anode or grounding device, and all grounding
devices must be interconnected.
Note: If you have a stainless steel propeller, you may need additional sacrificial anodes or a Volvo Penta active corro-
sion protection system to handle the added corrosion potential. Your Volvo Penta dealer will help you to decide which is
more appropriate for your boat.
Note: Boats that connect to an AC power source (shore power) will require protection against both galvanic and stray
current corrosion. For the added protection needed, a galvanic isolator may be installed in the grounding, or green,
wire between the boat and the shore power outlet on the dock. The isolator will block DC flow, but will permit the
passage of AC flow. If you are connected to an AC power source that is not equipped with a galvanic isolator, you may
need additional sacrificial anodes to handle the added corrosion potential.

Audible alarm _______________________________________________________________

The audible alarm will alert you to unacceptable or dangerously low oil pressure and/or high water temperature levels.

The audible alarm is capable of producing a warning sound up to 120 decibels. Prolonged exposure to this
audible alarm can cause hearing loss.
Engine systems ______________________________________________________________
Important engine systems include the cooling system, fuel system, exhaust system, electrical system, lubrication
system, and steering system.
Cooling system
The cooling system keeps the internal engine temperature below the boiling point of engine coolant. You will need to
take care of these cooling system components:
1. Raw water pump and impeller
2. Belts (may also be involved with other engine systems)
3. Hoses and clamps
Fuel system
The fuel system stores fuel for the engine, pumps gasoline through the fuel lines to the carburetor or fuel injectors, and
mixes fuel with air and sends the fuel-air mixture to the engine. You will need to take care of these fuel system compo-
nents:
1. Fuel pump
2. Fuel filter
3. Fuel quality

32
Exhaust system
The exhaust system passes the exhaust gases from the burnt fuel-air mixture through exhaust hoses to and out the
drive. You will need to take care of these exhaust system components:
1. Hoses and clamps
2. Exhaust manifold
3. Exhaust riser
Electrical system
The electrical system generates, stores, and regulates the flow of electricity needed to start the engine, fire the fuel-air
mixture to run the engine, and operate any electrical accessories on your boat. You will need to take care of these
electrical system components:
1. Battery and connections
2. Circuit breakers and fuses
3. Distributor cap and rotors
4. Spark plugs
Gi, GSi only
Your Volvo Penta engine features an Electronic Fuel Injection (EFI) system that uses a microprocessor (ECM) to
control idle air flow, fuel, and ignition.
Note: The electronics in the ECM require protection from false signals and interference. Never mount radio transmitter
antennas or sender cables near the ECM and never ground any wiring to the engine.
Lubrication system
The lubrication system circulates lubricants through your engine to keep moving parts moving freely and to reduce the
friction that heats up your engine. You will need to take care of these lubrication system components:
1. Oil changes
2. Oil filter
3. Oil quality
Steering system
The steering system allows you to steer your boat in the direction you want to go. You will need to take care of these
steering system components:
1. Remote control shift cable
2. Steering system cable
3. Power steering fluid
Drive components ____________________________________________________________
Important drive components include the lubrication system, anodes, power trim/tilt, universal joint, and propellers.

Emergency stop switch _______________________________________________________

An emergency stop switch may be a feature of your Volvo Penta-powered
boat. Volvo Penta highly recommends that you have an emergency stop
switch installed in your boat. To properly use this feature, attach the lanyard
securely to your clothing. Do not attach the lanyard to clothing that will
tear away before the lanyard is pulled from switch to stop the engine. If
the lanyard is too long, shorten the lanyard by knotting or looping it. Do not
cut and retie the lanyard.
Using this switch is simple and should not interfere with normal operation of
the boat. Be very careful to avoid accidentally pulling the lanyard during
normal operation: Unexpected loss of FORWARD motion will occur, and
passengers could be thrown forward. Also, significant internal engine
damage may occur.
33
In an emergency situation, any occupant of the boat can restart the engine. Just press in and hold the emergency
stop switch button, then follow normal starting procedures. When the button is released, the engine will stop.

The emergency stop switch can only be effective when it is in good working condition. Observe the following:
The lanyard must always be free of entanglements that could hinder its operation.
Once a month, check the switch for proper operation. With the engine running at idle in NEUTRAL, pull the
lanyard. If the engine does not stop, have your Volvo Penta dealer repair your emergency stop switch.
Engine protection mode (EFI systems)___________________________________________
In a low oil pressure or engine overheat situation, the EFI system enters an engine protection mode. In these situa-
tions, normal engine operation is limited to 2500 RPM or less. Above 2500 RPM the engine will exhibit poor running
characteristics. Use the oil pressure and water temperature gauges to verify a problem exists, then check the engine
for proper oil level and the water inlets for obstructions. The low oil pressure/engine overheat problem must be cor-
rected before the engine will return to normal operation.
To reset the engine protection mode after the problem is corrected, shut off the engine, then restart it.
Note: If the problem continues, contact your nearest Volvo Penta dealer and have the engine checked.
Instruments _________________________________________________________________
Before operating your Volvo Penta product, familiarize yourself with the instruments supplied with your boat. (Some
boats may not have Volvo Penta instruments. Read the boats owners manual to become familiar with the instruments
used.)
Engine instruments

34
Trim instruments
The trim instrument indicates the current trim position. Your boat may be equipped with an analog or a digital trim
instrument, as shown. The SX drive has an analog trim instrument only. The DP-S drive may have either an analog or
a digital trim instrument.
Analog trim instrument (SX, DP-S)
The analog trim instrument has three main
ranges:
Trim range: Use trim range for maximum com-
fort, under normal operation, from start to maxi-
mum speed.
Beach range: Use beach range for operating at
reduced speed in shallow water, where water
Analog trim instrument depth is uncertain. Also use this range when you
launch and take your boat out of water onto a
trailer ramp.
Lift range: Use lift range for lifting the drive to its maximum angle; however, this range cannot be used during boat
operation. Use this range when you are transporting your boat. The power trim has an automatic stop feature, which
cuts off the current when the drive reaches STOP. (STOP is automatically reset when trimming down.)

Operating in beach range or lift range will cause significant loss of maneuverability. Operating in beach range
above idle speed, or for prolonged periods of time, may cause serious drive damage.
Digital trim instrument (DP-S)
This instrument displays a figure (the angle of the drive to a stationary boat) within a range.
Trim range: Use trim range for maximum comfort, under normal operation, from start to
maximum speed (maximum range up to 5).
Beach range: Use beach range for operating at reduced speed in shallow water, where
water depth is uncertain. Also use this range when you launch and take your boat out of
Digital trim instrument
water onto a trailer ramp. Boat speed should always be low (range from 5 to 40).
Lift range: Flashing red warning light. Drive up completely (range from 41 to 51).

Operating in beach range or lift range will cause significant loss of maneuverability. Operating in beach range
above idle speed, or for prolonged periods of time, may cause serious drive damage.
LED display: Certain LEDs display at certain times for the digital trim instrument:
1 Flashes red within the range above 41.
2 Constant red within the range of 6 to 40.
3 Constant green within the range of 2 to 5.
4 Constant green within the range of 0 to 2.
5 Constant green in trimmed range up to 0.

LED display

35
6 Constant yellow in maximum trimmed position up to 0; flashes yellow when above 0. (Drive moves, bow is lowered.)
7 Constant yellow light within range of 2 to 5; flashes yellow when drive moves within trim range and bow is raised.
Trim/tilt motor protection
Always allow the trim/tilt switch to return to its center position when the drive unit reaches its maximum
raised or lowered position. This precaution will prevent your trim/tilt motor from overheating.
Impact protection
The trim/tilt system provides impact protection for the drive unit. If an impact occurs, the drive will kick up, thereby
helping to minimize drive damage. Impact damage, however, can occur in either FORWARD or REVERSE directions.
You must be careful when
You operate in FORWARD or REVERSE
You are backing at low speeds
You trailer your boat
You launch your boat.
Note: Impact damage is more likely to occur when you are in a turn where side loads are placed on the drive unit.
If you strike a solid object:
Throttle back and shut off the engine immediately.
Closely inspect the boat and drive unit (especially the transom shield assembly that contains steering system
components)
Check the engine compartment for water leakage.
If there is obvious or suspected damage, operate the boat at low RPM and take it to a Volvo Penta dealer for inspec-
tion. Have necessary repairs made immediately. Only operate your boat if absolutely necessary. Operating a
damaged unit could cause additional damage and could become very costly to repair.

Always check your boat and engine for damage. Failure to inspect for damage may
Result in sudden loss of steering control.
Adversely affect your boats capability to resist high-speed impacts.
When moving in REVERSE, there is no impact protection. Be very careful when moving in REVERSE. Do not
exceed 2500 RPM.
Other instruments See your Volvo Penta dealer for additional accessories specifically designed for your Volvo
Penta product.
Power trim/tilt _______________________________________________________________
Your Volvo Penta sterndrive is equipped with a power trim/tilt system as
standard equipment. The power trim/tilt allows you to change the angle of
the drive unit from the helm. Changing the angle of the drive unit in relation
to the boat bottom is called trimming. Trimming provides these benefits:
Improves acceleration to planing
Keeps the boat on plane at reduced throttle settings
Improves fuel economy
Provides smoother and/or drier ride in choppy water conditions
Increases maximum speed
36
If you do not wish to use this feature, you may leave the drive unit trimmed to the position that works best for you.

Propellers __________________________________________________________________
Volvo Penta makes a complete line of propellers designed to match the performance of the SX, DP, and DPX
sterndrives. For every combination of engine, sterndrive, hull, and application there is a Volvo Penta propeller that
provides optimum performance.
Many factors influence the way a propeller performs, including hull shape, onboard weight, engine horsepower, power
trim, and the way the boat is used. Ask your Volvo Penta dealer to assist you in choosing a propeller that is right for
your needs.
SX sterndrive propeller choices
1. Aluminum propellers
Volvo Pentas aluminum propellers are die-cast and dynamically balanced. Die cast propeller
blades are thinner than sand-cast blades, which means less cavitation, greater efficiency, and
longer service life. All aluminum propellers are given added protection against salt water with a
special baked-on corrosion resistant paint.
2. Stainless steel propellers
SX stainless steel propellers will maximize the performance of SX-powered boats. The blade
configuration and through-hub exhaust design of this propeller are important factors in the
propellers overall efficiency and performance This is a fast planing propeller designed to give your boat better accel-
eration and top end speed. The blade design has a longer tip and larger diameter, which creates a better grip on the
water.
3. High performance stainless steel propellers
This propeller has custom-cupped, high rake blades to provide better bow lift and make boats plane quick and run fast
a terrific choice for high performance boats.
Duoprop sterndrive propeller choices
The propellers for the Duoprop drive units have application and diameter/pitch
identification symbols: D0-D9, E2-E5, and F2-F9. The single number repre-
sents the diameter/pitch. The identification symbol and the front and rear
identification are stamped on the end of the propeller hubs. When replacement
is required, you may purchase the propellers individually, but you must make
sure they are the same size and same shaft (e.g., F7 front and rear). Do not
mix or split sets.
1. D series aluminum propellers
Volvo Pentas aluminum propellers are manufactured with a special aluminum
alloy that is highly resistant to the stress and effects of salt water. The unique
design of the Duoprop, with its two counter rotating propellers, is very important in achieving optimum performance.
Note: D5, D6, and D7 propellers are recommended for speeds below 40 MPH. For installations where D series
propellers are not recommended, F series stainless steel propellers should be used.
2. F series stainless steel propellers
A stainless steel Duoprop set is a very worthwhile upgrade from aluminum. They offer high performance through
thinner blades, powerful thrust, and virtually cavitation-free running; and greater torsion strength for higher accelera-
tion.
DPX sterndrive propeller choices
1. E series stainless steel propellers
High Performance DPX Duoprop propellers offer excellent, high speed performance with the precise handling and
efficiency that has made the Duoprop famous.

37
Drive unit, rotation, and propellers
SX drive unit
Your boat may be equipped with a single engine or twin engines. Propeller rotation is as viewed from the rear of the
boat facing forward.
Single engine installation
All single engine installations are set up for right-hand rotation (standard
rotation) and use right-hand propellers.
Twin engine installation
Your Volvo Penta drive unit can be set up to rotate in either direction. The
propeller, propeller shaft, and vertical drive shaft are the only parts that counter-
rotate. The engine always has standard rotation.
Twin engine installations should have the port drive unit set up for left-hand
rotation (counter-rotation) and the starboard drive unit set up for right-hand
rotation (standard rotation).

Some boat manufacturers may set up twin drive units so that the port drive unit set up for right-hand rotation
(standard rotation) and the starboard drive unit set up for left-hand rotation (counter-rotation). If you remove
the propellers and/or drive units, be very careful to attach the shift link in the same eccentric position it was in
when you removed it, and make sure that the propellers are not switched.
Duoprop drive unit
Duoprop drive units have counter-rotating propellers; it is not necessary to
change drive unit rotation. The propellers operate in sets:

The forward propeller is left-hand and rotates counter-clockwise.

The rear propeller is right-hand and rotates clockwise.
Propellers are installed in sets. You may purchase the propellers individually,
but make sure they are the same size and shaft (e.g., F7 front and rear). Do not
mix or split sets.
Propeller rotation
Right-hand propellers rotate clockwise to propel a boat forward. They are considered to be
standard rotation propellers. A drive unit set up for standard rotation must be equipped with a
standard rotation propeller. (Propeller rotation is as viewed from the rear of the boat looking
forward.)
Left-hand propellers rotate counterclockwise to propel a boat forward. They are considered to
be counter-rotation propellers. A drive unit set up for counter rotation must be equipped with a
counter-rotation propeller. (Propeller rotation is as viewed from the rear of the boat looking
forward.)
Note: Duoprop and DPX drive units have counter-rotating propellers. See above for a more
detailed description.

38
Never exchange a right-hand propeller with a left-hand propeller. This would result in your boat being pro-
pelled in reverse when the engine is operating in forward gear, and forward when the engine is operating in
reverse gear.
Whenever you have the propellers serviced, shift into FORWARD or REVERSE at idle speed and determine if the boat
moves in the direction indicated by the position of the control handle. If the boat moves opposite to the direction
indicated by the control handle, the propellers are switched.
Your Volvo Penta sterndrive is equipped with a propeller designed to give top performance and maximum economy
under all operating conditions. To obtain peak performance, the engine RPM at full throttle must fall in the specified
operating range at normal load conditions at favorable/best trim settings (trim set to provide the most speed with the
smoothest ride).

Engine Full Throttle Operating Range Engine Full Throttle Operating Range
3.0 GS 4200 - 4600 RPM 5.7 GS 4400 - 4800 RPM
4.3 GL/GS/Gi 4200 - 4600 RPM 5.7 Gsi 4600 - 5000 RPM
5.0 GL 4400 - 4800 RPM 7.4 Gi 4200 - 4600 RPM
5.0 Gi 4600 - 5000 RPM 7.4 Gsi 4800 - 5200 RPM

If full throttle RPM is below the recommended operating range, propeller(s) with lower pitch should be used.
If full throttle RPM is above the recommended operating range, propeller(s) with higher pitch should be used.
To provide your boat with the best engine life, fuel economy, and performance, select the correct propeller to allow the
engine to run at full throttle in the recommended operating range. Your Volvo Penta dealer will help you to choose the
correct propeller(s) for your application.

Replace a damaged propeller right away. Operate your boat with extreme caution if a propeller is damaged
while you are boating.
Do not operate a DP model with only one propeller, as this will cause damage to propeller shafts.

Remote controls _____________________________________________________________

Note: Some boats may not be equipped with Volvo
Penta remote controls. If you do not have Volvo Penta
controls, their operation and function may differ from
Volvo Penta controls.
Volvo Penta controls have these important features:
A single lever, which allows you to select FOR-
WARD or REVERSE, regulate engine speed, and
ensure shifting is done at low engine speed.
A start-in-NEUTRAL-only feature to prevent you
from starting your drive in gear.
Concealed side mount controls have a NEU-
TRAL lock button to prevent accidental shifting. It must be squeezed to permit shifting from NEUTRAL to FOR-
WARD or REVERSE. The binnacle mount controls do not have a NEUTRAL lock, but do have a NEUTRAL detent.
39
Your boat should be equipped by the manufacturer with a remote control with
protection to prevent starting in gear. Use only a remote control unit with
start-in-neutral-only feature. This feature can prevent injury resulting from the
propeller turning unexpectedly, or the boat moving suddenly.
The shift mechanism on all Volvo Penta controls can be disengaged to allow for easier
starting and engine warm-up. Control panel
Trim controls
Trimming (raising and lowering the drive) can be performed by using
A separate control panel on the instrument panel
A control button on the control lever
The control buttons on the port control lever in a twin installation
The current trim position is indicated on a special trim gauge.
Operating trim controls
Control panel Control lever
The control panel has three buttons:
The center button moves the drive trim out while it the raises the boats bow.
The lower button moves the drive trim in while it the lowers the boats bow.
The top button disconnects a catch so that the drive can be trimmed into the
BEACH position. (Press this button and the center button at the same time.)
Control lever
The control button on the control lever has two functions:
Pressing the top half of the button moves the drive trim out while it the raises the
boats bow
Control lever with catch button
Pressing the bottom half of the button moves the drive trim in while it the lowers the (single installation)
boats bow.
You must press a separate switch on the instrument panel to disconnect the catch so
that the drive can be trimmed into the BEACH position.
Control lever with catch button (single installation)
A tumbler switch on the control lever allows you to trim the drive:
Pressing the tumbler switch up moves the drive trim out while it the raises the boats
bow.
Pressing the tumbler switch down moves the drive trim in while it the lowers the
boats bow.
The catch button disconnects a catch so that the drive can be trimmed into the
BEACH position.
Control lever with catch button (twin installation)
There are two tumbler switches on the port control lever, which gives you the capability
of individual adjustment of the drive trim.
Pressing the switches up moves the drive trim out while it the raises the boats bow. Control lever with catch button
(twin installation)
Pressing the tumbler switches down moves the drive trim in while it the lowers the

40
 boats bow.
The catch buttons disconnect a catch so that the drive can be trimmed into the BEACH position.
Remote diagnostic uplink system _______________________________________________
Your boat may be equipped with a diagnostic uplink system, which
allows you to use a cellular phone to access remote communication
with Volvo Action Service, a 24-hour per day customer assistance
service. Your diagnostic uplink system consists of
IMPORTANT
a cell phone handset Before you operate your cell phone for
a remote access panel the first time, you must register the
Setting up the diagnostic uplink system cell phone phone with a cellular phone service
provider. You will need to provide this
You will hook up your cell phone to the box identified as the Remote information, also found on the product
Diagnostics Cellular Link: label on the phone itself:
1. Make sure the auxiliary switch powering the system is OFF. Phone manufacturer Motorola
2. Lift up the cover on the cellular link box. Phone model S-5690
3. Plug in the handset. Serial number unique to each phone
4. Turn the auxiliary switch ON.
5. The phone will power up as a standard cellular phone.
6. Check the access panel indicator to see the operational state, WHICH SHOULD BE SOLID FOR NORMAL
OPERATION.
Solid: Voice mode. Means that phone is operational, and system is up and running. In voice mode, you may
use your cell phone as a regular telephone, or use it only as an emergency phone to access the remote
diagnostic uplink capability.
Fast flash: Data mode. Means that you may use your phone to send a fax via your laptop computer.
Slow flash: Phone problems. Check your phone user manual for more detailed instructions.
Using the remote diagnostic uplink system
If you find that you are having a problem that requires technical assistance:
1. Call Volvo Action Service toll-free at 1-877-337-3682, then press the SEND button.
2. The VAS coordinator will assist you.
3. Go to data mode:
Press the VOICE/DATA button on the bulkhead panel.
Press the END button on the cell phone handset.
When data transfer begins, the bulkhead panel light will flash rapidly. (This may take a few seconds for the
modems to establish connections.)
4. The bulkhead panel light will return to a steady ON condition to signal you to return to VOICE mode.
5. Return to voice mode:
Press the SEND button on the cell phone handset.
Press the VOICE/DATA button on the bulkhead panel after the voice/data light returns to a steady ON condi-
tion.
6. The VAS coordinator will discuss his findings and advise you on how to proceed.
7. Press the END button to terminate the phone call on the cell phone handset.
8. Switch off auxiliary power to the diagnostic uplink system.
9. Disconnect the cell phone from the bulkhead panel.

41
42
 OPERATION

Engine break-in period ________________________________________________________

Note: To ensure proper lubrication during the break-in period, do not remove factory break-in oil until after the 20-hour
break-in is completed. The First Service inspection should be carried out after 20 hours of operation.

Failure to follow engine break-in procedures can result in serious engine damage.
Never run an engine at a constant engine speed for long periods during the break-in period.
Do not run engine at a constant RPM for prolonged periods of time during the break-in period.
All Volvo Penta engines have been run for a short time during a final test at the factory. You must follow the engine
break-in procedure during the first 20 hours of operation to ensure maximum performance and longest engine life.
During the break-in period, watch out for the following items during the initial engine run:
1. Check engine oil level frequently.

IMPORTANT
Be sure to check the oil level frequently during the first 50 hours of operation, since the oil consumption will
be high until the piston rings are properly seated.
The engine may use more engine oil during the running-in period than would otherwise be normal. Check the oil
level regularly and more frequently during the running-in period.
Maintain oil level in the safe range, between the ADD and FULL marks on dipstick. Somewhat higher oil
consumption is normal until the piston rings have seated.
If you have a problem getting a good oil level reading on the dipstick, rotate the dipstick 180 in the dipstick
tube.
When adding engine oil, use Volvo Penta engine oils for gasoline engines, or a good quality oil (API Service
CE/SG or better) of the same viscosity that meets General Motors Specification GM-6094-M. Use the following
chart to select the SAE viscosity that matches the temperature range in which you expect to operate.

SAE Viscosity Chart

Lowest Anticipated Recommended SAE
Temperature Viscosity Oils
SAE 30*
32 F (0 C) above SAE 20W/50
SAE 15W/50
0 F (-18 C) 32 F (0 C) SAE 20W-20
Below 0 F (-18 C) SAE 10W

*SAE 30 Volvo Penta DuraPlus Synthetic Motor Oil (P/N 3851230-7) (U.S. and Canada Only)
Note: To ensure proper lubrication during the break-in period, do not remove factory break-in oil until after the
20-hour break-in is completed.

43
2. Watch the oil pressure gauge.
Oil pressure will rise as RPM increases, and fall as RPM decreases. In addition, cold oil will generally
show higher oil pressure for any specific RPM than hot oil. Both of these conditions reflect normal engine
operation.
If the oil indicator fluctuates when the boat is turning, climbing on plane, etc., the oil pickup screen may not
be covered with oil. Check the oil dipstick. If required add oil, but do not overfill. If the oil level is correct
and the condition persists, ask your Volvo Penta dealer to check for possible gauge or oil pump malfunc-
tion.
3. Watch the engine temperature indicator to be sure there is proper water circulation.

IMPORTANT
Failure to follow the break-in procedure may void the engine warranty.
First two hours
1. For the first five to ten minutes of operation, operate the engine at a fast idle (above 1500 RPM).
2. During the remaining first two hours of operation, accelerate to bring the boat onto plane quickly; bring the
throttle back to maintain a planing attitude.
During this period, vary the engine speed frequently by accelerating to approximately throttle for two to three
minutes, then back to minimum cruising speed.
3. After the engine has reached operating temperature, momentarily reduce engine speed, then increase engine
speed, to assist break-in of rings and bearings. Maintain plane to avoid excessive engine load.

IMPORTANT
For this initial two hour break-in, do not run the engine at any constant RPM for prolonged periods of time.
Next eight hours
1. During the next eight hours, continue to operate at approximately throttle or less (minimum cruising speed).
Occasionally reduce throttle to idle speed for a cooling period.
2. During this eight hours of operation you may operate at full throttle for periods of less than two minutes.
Final ten hours
1. During the final ten hours of break-in, you may operate at full throttle for five to ten minutes at a time.
2. After warming the engine to operating temperature, momentarily increase engine speed.
3. Occasionally reduce engine speed to idle to provide cooling periods.
At the end of the 20 hour break-in period, drain the engine oil and replace the oil filter. Fill the crankcase with Volvo
Pentas DuraPlus premium engine oil labeled for Service CE/SG.
First service inspection (Dealer 20-hour check) ___________________________________
To ensure your continued boating enjoyment, we recommend that you return your Volvo Penta product to your Volvo
Penta dealer for a 20-hour check. This 20-hour check will prevent a minor problem from getting worse, and helps
ensure a trouble-free boating season. When following the Volvo Penta guidelines, your dealer will service these items:
Start the engine and check that
No leakage of fuel, oil, water, or exhaust gases occurs.
Engine oil pressure and temperature are normal.
All cables and controls operate correctly.
All gauges, instruments, and alarms operate correctly.
Steering system operates correctly.
44
 Engine ignition timing and idle RPM are within specifications.
Power trim system operates correctly.
Stop the engine and
Change engine oil and oil filter.
Change fuel/water separator filter.
Clean seawater strainer (if equipped).
Check fluid levels and fluid condition in sterndrive or inboard transmission, power steering pump, and trim
pump.
Check propeller(s) and propeller(s) fasteners.
Check condition of battery and battery cable connections.
Check drive belt(s) tension and condition.
Lubricate all grease fittings and linkages following service recommendations.
Check tightness of all water, fuel, and exhaust clamps, fittings, and drain plugs.
Restart the engine and recheck that
No leakage of fuel, oil, water, or exhaust gases occurs.
Engine oil pressure and temperature are normal.
This is a perfect time to discuss with your Volvo Penta dealer any questions about your engine that may have arisen
during the first 20 hours of operation and establish a routine preventive maintenance schedule.
In the US, Canada, and Mexico, the 20-hour check is paid for by the boat owner and performed by your Volvo Penta
dealer at local rates. In other markets, warranty inspection is paid for according to the warranty policy for Importers.

Operating after break-in period _________________________________________________

After the break-in period, the engine can be operated at any RPM from idle to full throttle. Cruising at 3600 RPM or
less, however, saves fuel, reduces noise, and prolongs engine life.
Before starting _______________________________________________________________
Note: Do not start the engine out of the water unless you have an optional flushing adapter. Follow the adapter
manufacturers instructions for attaching and running the engine out of water.
Familiarize yourself with the operation of the remote control supplied with your boat, then proceed as follows.

To prevent a possible explosion, operate the blower as recommended by the boat manufacturer before start-
ing the engine. If the engine compartment is not equipped with a blower, open the engine cover or hatch
before starting to disperse any gasoline fumes that may be present. Leave the hatch open until after the
engine is running.
1. Start the boats bilge blower and run for at least four (4) minutes. Frequently check boats bilge area for gasoline
fumes.
2. Check the bilge for excessive water accumulation. Always keep the bilge clean and dry.

The water level in the boats bilge will increase when you operate your boat at a high incline before you reach
planing speed. Excessive water in the bilge can cause engine damage.
3. Open the fuel cock (if so equipped).
4. Make sure that there are no fuel, engine coolant, or oil leaks.
5. Check engine oil level.
45
6. Switch on the main switches (if so equipped).
7. Insert the key into the ignition switch. Turn the key one step to the right to switch on engine system voltage and
instrumentation.
8. Make sure that you have enough gasoline.
9. Lower the drive unit; make sure the water intakes are submerged. (There should be no obstructions in the water
near the propellers.)
Starting the engine, cold start __________________________________________________
GL, GS models:
A cold engine may require priming before you can start it:
1. Turn the ignition switch OFF.
2. Disengage the shift mechanism.
3. Move the remote control handle to FULL THROTTLE (this operates the accelerator pump and primes the engine).
4. Repeat priming if necessary.
5. Return the remote control handle to FAST IDLE.
6. Turn the ignition switch to START and hold it there until the engine starts, but for no longer than 10 seconds.
Note: Too much priming may flood the engine.
Gi, GSi models:
1. Move the control handle to the NEUTRAL detent position.
2. Turn the key switch to START and hold until engine starts, for no longer than ten seconds. If the engine does not
start, let go momentarily, then try again.
3. As soon as engine starts, release key to ON or RUN.
If the engine floods
GL, GS models:
1. Disengage the shift mechanism.
2. Move the remote control handle to FULL THROTTLE.
3. Turn the key switch to START.
4. As soon as the engine starts:
Return the remote control handle to IDLE.
Turn the key to ON or RUN.
Move the remote control handle to FAST IDLE to warm up the engine. Do not exceed 1000 RPM.
Gi, GSi models: Advance the control handle to throttle to clear a flooded engine. In this throttle position, with the
engine speed below 400 RPM (cranking speed), the ECM turns off the fuel injectors so no fuel is delivered. When the
throttle position is moved to full throttle or less than throttle, the ECM returns to the starting mode.
Be prepared to quickly move the control handle to IDLE once the engine starts. This will avoid speeding and possibly
damaging the engine.

Immediately after engine start-up, look at all instruments. If any readings are abnormal, stop the engine and
determine the cause.

46
If you do not move the remote control handle to IDLE as soon as the engine starts, the engine will overspeed
and could be damaged.
When you start your engine for the first time after off-season storage, always run the engine in IDLE for one
minute to allow the water pump to prime.

Starting the engine (warm start) ________________________________________________

1. Move the control handle to the NEUTRAL detent position.
2. Turn the key switch to START and hold until the engine starts, but for no longer than 10 seconds. If the engine does
not start, let go momentarily, then try again.
3. As soon as the engine starts, release the key to ON or RUN.

Never leave the key in the ON position with the engine not running. This could damage the engine. Never turn
the key to START when the engine is running. This could damage the engine.
If the engine floods:
GL, GS models:
1. Disengage the shift mechanism.
2. Move the remote control handle to FULL THROTTLE.
3. Turn the key switch to START.
4. As soon as the engine starts:
Return the remote control handle to IDLE.
Turn the key to ON or RUN.
Move the remote control handle to FAST IDLE to warm up the engine. Do not exceed 1000 RPM.
Gi, GSi models: Advance the control handle to throttle to clear a flooded engine. In this throttle position, with the
engine speed below 400 RPM (cranking speed), the ECM turns off the fuel injectors so no fuel is delivered. When the
throttle position is moved to full throttle or less than throttle, the ECM returns to the starting mode.
Be prepared to quickly move the control handle to IDLE once the engine starts. This will avoid speeding and possibly
damaging the engine.

Immediately after engine start-up, look at all instruments. If any readings are abnormal, stop the engine and
determine the cause.

Stopping the engine _______________________________________________

1. Move the remote control handle to NEUTRAL.
2. Turn ignition key to OFF.

Do not stop the engine at speeds above idle or speed up the engine while turning off the ignition. Engine
damage could result.
47
Operating remote controls _____________________________________________________
Familiarize yourself with remote control operations before starting the engine.
Side mount control
To disengage the shift mechanism:
1. Place the control handle in NEUTRAL.
2. Press both NEUTRAL lock button and the SHIFT DISENGAGE button.
3. Move control handle FORWARD to increase throttle.
The NEUTRAL lock and shift mechanism will automatically engage when the control handle is
returned to NEUTRAL.

Top mount control

To disengage the shift mechanism:
1. Push in and hold shift disengagement button.
2. Move control handle FORWARD to increase throttle.
The shift mechanism will automatically engage when the control handle is
returned to NEUTRAL.

Steering system operation _____________________________________________________

The steering system for your Volvo Penta sterndrive is operated by a steering cable connected to the helm. Restricting
movement of the steering cable will limit or stop the steering systems hydraulic assist.
Do not interfere with or restrict steering cable movement through the last 90 of bend at the engine. Do not use cable
retainers, clamps or tie straps. Using one or all of these could restrict the cable movement near the engine. Do not tie
wiring harnesses or other control cables to the steering cable. Make sure deck combing and bulkheads allow for
steering cable movement.
If the power steering system stops working, it will feel harder to steer. If this condition occurs, look for pos-
sible causes and fix them if possible. If the power steering system cannot be corrected on board, proceed at a
reduced speed. You will be able to steer the boat, but with increased effort. See your authorized Volvo Penta
dealer as soon as possible to correct your power steering system.
At slow speeds (no wake), your boat may tend to wander. This is normal and may be overcome by anticipating bow
direction and correcting with steering wheel. A slightly higher throttle and trim setting may also lessen the tendency to
wander. Changing weight distribution, aft to forward, can also affect slow speed steering.
Twin unit steering
Twin engine boats may have only one engine with a fully operational power steering system. That power steering
system is on the starboard engine; therefore, when operating on a single engine use the starboard engine.
Note: Using a port engine that does not have a functional power steering system will cause an increased effort in
steering control, due to absence of power assist.
Some twin engine boats may have both engine power steering systems coupled together with a priority valve. This
allows the use of either engine to provide power assist steering.
48
Power trim and tilt operation ___________________________________________________
Power trim operation
The power trim is normally used before you accelerate onto plane, after you reach the desired RPM or boat speed, and
when there is a change in water or boating conditions. Locate passengers and equipment in the boat so that the weight
is balanced fore and aft, and side to side. Trimming will not cancel an unbalanced load.
To operate the trim, push and hold the switch bow-up or bow-down until the desired bow position is reached. The
trim may be operated at any boat speed or at rest. Avoid operating the trim system when running in reverse. Observe
the trim/tilt gauge, which indicates the bow position achieved. The upper scale (0 to 5) of the trim gauge indicates the
bow-up positions, and lower scale (6 to 10) of the trim gauge indicates the bow-down positions.
Determining the proper trim
The effect of the maximum bow-up and bow-down positions will be similar for most boats. The bow position best for
your operating conditions could be at any trim setting between the maximum bow-up and bow-down positions.
The boat will be properly trimmed when the trim angle provides the best boat performance for your operating condi-
tions. On models without power steering, the trim position that provides a balanced steering load is desirable.
To familiarize yourself with the power trim, make test runs at slower speeds and at various trim positions to see the
effect of trimming. Note the time it takes for the boat to plane. Watch the tachometer and speedometer readings and
the ride action of the boat. Read the following paragraphs under Operating in Bow-Up Position and Operating in Bow
Down Position.
Operating in bow-up position
The bow-up position is normally used for cruising, running with a choppy wave
condition, or running at full speed. In a full bow-up position the boat may tend to self-
steer. You may have to compensate with the steering wheel to keep the boat in a
straight-ahead path. In this position the boats bow will tend to raise clear of the water.
Excessive bow-up trim will cause propeller ventilation resulting in propeller slippage.
Engine RPM will also increase, but boat speed will not increase and may even drop.

Use caution when operating in rough water or crossing another boats wake. Excessive bow-up trim may
result in the boats bow rising rapidly and possibly throwing the boats occupants into the water.
Operating in bow-down position
The bow-down position is normally used for acceleration onto plane, operating at
slow planing speeds, and running against a choppy wave condition. In the fully
bow-down position the boat may tend to self-steer. You may have to compensate with
the steering wheel to keep the boat in a straight-ahead path. In this position the boats
bow will tend to go deeper into the water. If the boat is operated at high speed and/or
against high waves, the bow of the boat will plow into the water. The boat may tend to
bow steer or spin about rapidly and possibly eject occupants.

The boat trim should be adjusted to provide balanced steering as soon as possible each time you get under-
way. Some boat/motor/propeller combinations may encounter boat instability and/or high steering torque
when operated at or near the limits of the bow-up or bow-down positions. Boat stability and steering
torque can also vary due to changing water conditions. If you experience boat instability and/or high steering
torque, see your Volvo Penta dealer to correct these conditions.
49
Power tilt operation
Tilting is normally used for raising the drive unit to obtain clearance when beaching,
launching from a trailer, or mooring. When tilting the drive unit, the boat should be at
rest or at idle speed only.
The trim/tilt switch controls the tilting feature of the drive unit. When the trim/tilt switch
is held in the bow-up position, the drive unit tilts up until the switch is released or the
drive unit reaches the maximum tilt position. The trim/tilt gauge will indicate the tilt
position whenever the drive unit is in the tilt range.

Never exceed 1000 RPM when operating the drive unit in the tilted position, because it may damage the drive
system. Never run the engine when the drive unit is tilted more then 30 or the drive will be damaged.
Never operate the drive unit out of water without a flushing kit attached. The water pump may be damaged or
engine may overheat.

To avoid possible contact with the propeller, never use the drive unit as a ladder or as a lift to board the boat.
Never board at the rear of the boat when the engine is running, even if the engine is operating in neutral.
Personal injury could result from contact with rotating engine parts and propeller.
Any malfunction of the trim/tilt system could result in a loss of impact protection. Malfunction can also result
in loss of reverse thrust capability. If malfunction occurs, see your authorized Volvo Penta dealer.
Power trim/tilt switch operation
Trimming and tilting the drive is done from a control switch
mounted on the remote control or by using the switches on the
dash. When using the dash mounted switches, the bottom
button lowers the bow and the button n raises the bow. The
switch on the remote control lever raises and lowers the drive
when its upper or lower segment is pressed.
Note: Allow the trim/tilt switch to return to its center position
when the drive unit reaches the maximum raised or lowered
position. This will prevent your trim/tilt motor from overheating.
The trim/tilt motor is protected from overheating by an internal
thermal overload switch. If the electric motor stops while tilting,
release the switch and allow the overload switch to cool and automatically reset itself. When the overload switch has
reset, tilting may be resumed. Make sure the drive unit is not being restrained, causing the motor to overheat. If the
electric motor still does not operate, check the in-line 5-amp fuse in the remote control handle, or the 50-amp circuit
breaker on the engine.

50
Power trim/tilt switch and gauge location
The power trim/tilt switch is located on the remote control handle or on the boats dashboard. The trim indicator dis-
plays the drive position in the Trim range. With dual installations, it is permissible to individually trim the drive in Trim
range. When the drive is in Beach range, 7 to 10, boat speed must be lower than planing speed. The engine must be
stopped when fully tiIted.

For twin installations, if the drives need to be trimmed or tilted, both drives must be moved at the same time
(i.e., parallel) to prevent unnecessary stress on the tie rod between the drives. When trimming/tilting in paral-
lel, both drives must be trimmed to their full forward position first. Start trimming/tilting from this position.
Note: There is no automatic stop function between the Trim range and Beach range. Check the trim indicator carefully
during trim operation.

Shifting and controlling speed _________________________________________________

IMPORTANT
Carefully check the function of all control and engine systems before leaving the dock.
1. Move the remote control handle to the NEUTRAL detent (idle) position. This will engage NEUTRAL START switch
and allow engine to start. Check in front and behind boat for people or obstructions before shifting.
2. Do not shift if engine speed is above 800 RPM.
3. To go FORWARD - Actuate the NEUTRAL lock mechanism and move the shift handle forward. Throttle movement
will begin after the FORWARD gear engages.
4. To go in REVERSE - Actuate the NEUTRAL lock mechanism and move the shift handle rearward. Throttle move-
ment will begin after the REVERSE gear engages.
5. To go from FORWARD to REVERSE, or REVERSE to FORWARD, always pause at NEUTRAL and allow engine
speed to return to idle. Do not shift from FORWARD to REVERSE when the boat is planing.
6. After shifting is completed, continue to move the control handle slowly in the desired direction to increase speed.

Any time you operate your boat, be aware of changes in shift system operation. A sudden increase in shift
effort at the remote control handle, or other abnormal operation, indicates a possible problem in the shift
system. If this occurs, take the following precautions:
With the engine running and the boat securely tied to the dock, shift the reverse gear into FORWARD and
REVERSE to make sure there is gear engagement. Do not exceed idle RPM.
Whenever you dock your boat, perform all docking maneuvers at slow speed. Pay special attention to
other boaters. Inform passengers of potential problems and take all precautions necessary to ensure their
safety.
If you suspect there is a problem, see your Volvo Penta dealer as soon as possible for proper diagnosis and
required service or adjustment. Continued operation could result in damage to the shift mechanism and loss
of shift and throttle control that could result in personal injury.

51
Checking instruments ________________________________________________________
Check your instruments often. Stop the boat engine if you have an abnormal reading or if your audible alarm sounds.
Normal readings are shown below.

Special boating circumstances _________________________________________________

Engine protection mode operation (fuel injection systems)
In a low oil pressure or engine overheat situation, the EFI system enters an Engine Protection Mode. When this mode
is entered, normal engine operation is limited to 2500 RPM or less. Above 2500 RPM the engine will exhibit poor
running characteristics. Use the oil pressure and water temperature gauges to verify a problem exists, then check the
engine crankcase for proper oil level and the water inlets for obstructions. The low oil pressure/engine overheat
problem must be corrected before the engine will return to normal operation. To leave the Engine Protection Mode after
the problem is corrected, turn engine off then START again.
Note: If the problem continues, contact your nearest Volvo Penta dealer and have the engine checked.
Shallow water operation
You may tilt the drive unit to reduce the draft for shallow water running as long as you do not exceed 1000 RPM.
Exceeding 1000 RPM is not necessary. It will only increase the boat wake and will not increase boat speed appreciably.

Exceeding 1000 RPM with the drive unit tilted could damage drive train components. This type of damage is
not covered by warranty. Never attempt to plane the boat or exceed 1000 rpm with the drive unit in a partially
tilted position. Always return to the trim range as soon as possible to avoid damage to drive train.
Never run the engine when the drive unit is tilted more then 30 or the drive will be damaged.
When operating in shallow water, be sure the water intakes located in the lower gear unit are submerged at all times.
Proceed at slow speed and lower drive unit immediately when deeper water is reached.
High altitude operation
Volvo Penta EFI engines have programmed altitude compensation; however, there may be a slight performance loss at
altitudes above 5000 feet due to lower air density. If you are boating above 5000 feet for a short time, a lower pitch
propeller will restore some of the lost performance. Long term use above altitudes of 5000 ft. may require a change in
gear ratio.
Volvo Penta carbureted engines may require mechanical modifications. See your Volvo Penta dealer for more informa-
tion.

52
Operating procedure for freezing temperatures
When freezing temperatures are forecast and the boat will be operated and left in the water, the drive unit must remain
in the tilted down (submerged) position at all times to prevent water in the drive unit from freezing. Upon completion of
engine operation, drain the engine as described in the Maintenance section.
Salt water operation
Your can use your Volvo Penta sterndrive in either fresh or salt water.
We recommend that you use fresh water to flush out the engine and drive after you use it in polluted or salt water. This
will prolong the service life of the manifolds and risers. Contact your authorized Volvo Penta dealer for an engine
flushing kit that allows you to flush out the engine whether it is in or out of the water.
If your boat is moored for long periods of time, tilt the drive unit out of the water. After you remove your boat from the
water, lower the drive unit to the RUN (down) position until the cooling system drains thoroughly.
Rinse the entire drive exterior with fresh water, then dry it and spray it with anti-corrosion spray.
Twin unit operation
When leaving or approaching the dock, or for any close maneuvering at slow speed, place the starboard engine in
NEUTRAL, on standby, and use the port engine with the control nearest the operator. The use of one control is very
effective and more convenient.
In the event that the port engine being used for maneuvering stops, you can immediately go to the starboard engine
which has been on standby.

If maneuvering with an engine that has the power steering pump which stops, the power steering assist is
lost. Failure to follow the above maneuvering procedure could result in a collision and personal injury.
Both engines must be running during close maneuvering or at slow speeds. If only one engine is running, water
may be forced back through the underwater exhaust outlet and cause serious engine damage.
Do not attempt to plane the boat while operating on a single engine. The propellers are selected for the boat to
operate optimally with twin engines. Operating with a single engine could cause engine damage.

Trailering your boat ___________________________________________________________

Before moving your boat, check the ground clearance of the drive unit. When trailering, the drive unit may be in the up
or down position. There must be at least 15 inches (38.1 cm) clearance between the lower gear unit and the ground. If
the clearance is less than 15 inches (38.1 cm), raise the drive unit.
Note: Be very careful when you back out of driveways or cross railroad tracks, so that the lower gear unit does not hit
the ground.
Make sure that the boat fits the trailer properly. In many cases, loss of performance and speed is due to improper
trailer support and too much tie-down pressure, which causes the boat bottom to deform. The boat should rest firmly
on the trailer with maximum tie-down pressure applied at the bow and transom only.

Propeller selection ___________________________________________________________

Your Volvo Penta dealer has chosen a propeller designed to deliver top performance and economy under most condi-
tions. To obtain the maximum percentage of available horsepower, the engine RPM at full throttle should be in the
specified full throttle operating range. Refer to Specifications on pages 95 through 100 for full throttle RPM range.
Propellers that allow full throttle operation at the upper end of the RPM range provide faster planing time for water
skiing or similar activities. Propellers that place full throttle operation RPM in the middle of the range provide improved
cruising fuel economy.
53
 If the engines full throttle RPM with a normal load is below the
specified range or on the low side of the range (1), use propellers
with less pitch to increase the RPM.
If the engines full throttle RPM exceeds the specified range (2),
use propellers with higher pitch to decrease the RPM.
Engine damage can result from incorrect propeller selection that
1. Prevents engine RPM from reaching the specified full throttle
operating range (e.g., laboring engine.) Install lower pitch
propeller(s).
2. Allows engine RPM above the specified full throttle operating
range (e.g., overspeeding engine). Install higher pitch propeller(s).

IMPORTANT
D-series aluminum propeller sets are not recommended for use on Duoprop-equipped boat and engine combi-
nations that are capable of speeds in excess of 43 MPH (35 knots). F-series stainless steel propeller sets
should be used in these applications.
If you use D-series aluminum propeller sets, you must also use an in-trim limiter kit. See your Volvo Penta
dealer.

54
 MAINTENANCE

Volvo Penta components meet U.S. Coast Guard requirements for explosion-proof parts. To prevent fire and
explosion, do not substitute automotive or other non-approved parts.

Maintenance schedule ________________________________________________________

The operation, maintenance, and care of the Volvo Penta engine and power package as outlined in the owners
manual are the owners responsibility. The owner must keep records of all maintenance services performed. This
record of proper maintenance may be required to determine warranty coverage on certain repairs and should be
transferred to each subsequent owner. If you are not sure of the proper maintenance procedures, contact the Volvo
Penta Consumer Affairs Department at the address on page 85 of this document.
Tighten/
Function Adjust Check Lubricate Fill Replace Torque
Weekly
Anodes, sacrificial
Cooling system, leakage
Emergency stop switch, clip, and lanyard
Fuel system (leakage)
Oil, engine crankcase
Oil, drive unit
Safety equipment
Shift system (operation)
Steering reservoir (fluid)
Steering system cable (operation)
Monthly
Battery and connections (water level)
Emergency stop switch, clip, and lanyard
Exhaust system hoses/clamps (leakage)
Every 50 operating hours
Battery and connections (water level)
Belts: alternator, idler, power steering, water
pump (4.3, 5.0 GL; 5.7 GS)
Exhaust system hoses/clamps (leakage)
Fasterners (screws, nuts, etc.)
Flame arrestor (mounting)
Fuel system (leakage)
Impeller, water pump *
Power steering (operation/fluid)
Power trim/tilt (operation/fluid)
Propeller and shaft
Remote control shift cable (damage)
Steering system cable (operation)

* Check at 50-hour intervals; replace as necessary or once every two years, whichever comes first.

55
 Tighten/
Function Adjust Check Lubricate Fill Replace Torque
Once per season *
Bellows and clamps, drive unit **
Exhaust manifold and risers
Distributor cap and rotors
Fuel filter, carburetor
Fuel filter, engine
Fuel system (leakage)
Impeller, water pump **
Oil, engine crankcase
Oil, drive unit
Oil filter (engine)
Propeller and shaft
Remote control shift cable (damage)
Spark plugs
Spark plug wires/boots (deterioration)
Steering system cable (operation)
Throttle cable (damage and operation)
Dealer only
Belt: serpentine (3.0 GS; all fuel-injected

models)
Carburetor adjustment (as needed)
Engine alignment and mounting screws
Exhaust manifold & risers (corrosion; blockage)
Gimbal bearing
PCV valve
Shift system (operation)
Universal joints
Universal joint bellows
Universal joint shaft splines

* Once per season or every 100 operating hours, whichever comes first.
** Check at 50-hour intervals; replace as necessary or once every two years, whichever comes first.

56
Preparing for boating after storage (summerization) _____________________________
1. Replace all drain plugs.
2. Replace rubber caps and clamps or plugs.
3. Connect hoses and check their condition; tighten clamps and connections.
4. Install boat drain plug, if removed.
5. Remove distributor cap and rotor.
6. Wipe inside of distributor cap dry with a clean cloth; spray with Volvo Penta anti-corrosion spray.
7. Replace rotor and distributor cap.
8. Clean battery terminals and check battery charge.
9. With ignition switch in OFF position, install battery and attach battery cables.
10.Spray terminals with Volvo Penta anti-corrosion spray.
11. Open the fuel shut-off valve and check all fuel line connections for leaks.
12.Check the flame arrestor and clean if necessary.
13.Make a thorough check of boat and engine for loose or missing nuts and screws.
14.Pump the bilge dry and air out engine compartment. Federal, state, and/or local regulations prohibit the
pumping of oil into any navigable waters.
15.Check all reservoir oil levels and fill as necessary.
16.Check drive and transom shield anodes. Clean or replace as necessary.

Off-season storage preparations (winterization) _________________________________

Be sure to properly winterize your Volvo Penta equipment. Engine or drive damage can result from ignoring simple
preventive maintenance steps during autumn. Winterizing gives you the assurance that your engine will run more
reliably and economically in the springtime.
Volvo Penta recommends that you have your Volvo Penta dealer winterize your engine and drive. Your dealer will
provide the proper servicing and maintenance to ensure that your equipment is treated and stored properly.

Exhaust system ______________________________________________________________

Engine exhaust system
Periodically inspect the engine exhaust system. Check for
Deteriorated hoses
Burned hoses
Loose clamps
Evidence of water leaks
Corrosion or blockage in the exhaust manifold and riser

Replace damaged or defective components, and securely

tighten all clamps. Any exhaust leak must be repaired
before you operate your boat. Exhaust leaks release fumes
that can create hazardous conditions for operator and
passengers.
57
Drive unit bellows

If you work on the drive bellows, secure the drive unit in a raised position in such a way that it cannot fall. A
falling drive unit may cause serious bodily injury.
Check the drive unit bellows for fractures and deterioration.
Check tightness of all hose clamps.
Check the drive unit bellows and clamps annually.
Replace drive unit bellows and clamps every second year. You may order the
bellows separately, or as part of an accessories kit. (The accessories kit also includes
o-rings, oils, washers, seals, and anodes.)
(DPX only) If hose clamps must be tightened, or hoses and clamps must be replaced, the clamp screw positions
must be maintained as shown.

Fuel system _________________________________________________________________

Gasoline is extremely flammable and highly explosive. ALWAYS turn off the engine before fueling. Do not
smoke or allow open flames or sparks near the boat when adding fuel.
When filling the gas tank, ground the tank to the source of gasoline by holding the hose nozzle firmly against
the side of the deck filler plate, or ground it in some other manner. This action prevents static electricity
build-up that could cause sparks and ignite fuel vapors.
Gasoline recommendations
USE ONLY UNLEADED FUEL. Maximum engine performance requires the use of lead-free gasoline with the following
minimum or higher octane specification:
Inside the U.S.: (R+M)/2 (AKI) 89
Outside the U.S.: (RON) 93
If fuels with 89 AKI pump posted (93 RON) octane number or higher are not available, lower octane fuels (minimum 87
AKI [90 RON] octane) can be used. With the use of lower octane fuel, a slight decrease in power can be expected.
Premium fuel contains injector cleaners and other additives that protect the fuel system and provide optimum perfor-
mance. Volvo Penta strongly recommends the use of premium grade fuels.
Gasoline will degrade over time. Always buy your gasoline from a reputable dealer.

Engine damage resulting from the use of a lower octane gasoline than 87 AKI (90 RON) is considered misuse
of the engine. Any resulting engine damage will not be covered by the warranty.
Gasoline containing alcohol
Many brands of gasoline being sold today contain alcohol. Two commonly used alcohol additives are Ethanol (ethyl
alcohol) and Methanol (methyl alcohol).

58
See your boats owners manual to see if the boats fuel system is compatible with alcohol blended fuels. If it is, your
engine may be operated using gasoline blended with no more than 10% Ethanol meeting the minimum octane specifi-
cation.

Do not use any gasoline that contains METHANOL. Serious damage will result from the continued use of fuel
containing METHANOL. Any resulting engine damage will not be covered by the warranty.
If you use gasoline that contains ethanol, be aware of the following:
The engine will operate leaner with ethanol blended fuel. This may cause engine problems such as vapor lock, low
speed stall, or hard starting.
Ethanol blended fuels attract and hold moisture. Moisture inside fuel tanks can cause corrosion of the tank mate-
rial. Inspect fuel tanks at least annually. Replace fuel tanks if inspection indicates leakage or corrosion.
Detonation (spark knock)
Carbureted models: Detonation, or spark knock, in a marine engine is not necessarily audible. Overheating and
continued running (dieseling) after ignition shutoff are indications of detonation in a marine engine. If you suspect
detonation or spark knock, and the engine is tuned properly, change to a higher octane fuel.
EFI models: Detonation, or spark knock, is continually monitored by the electronic fuel injection (EFI) system. The
EFIs computer (ECM) will automatically alter spark advance to help to prevent engine damage if knock is detected,
and there will be a slight loss of power.
Preventing gum formation and corrosion in the fuel system
To prevent gum formation and corrosion in the fuel system, use a fuel stabilizer in the gasoline if it has been in the tank
for more than two weeks. Fuel stabilizer is available from your Volvo Penta dealer.
EFI models: Some marinas sell fuel with lead additives. Do not use leaded fuel, as it may plug the fuel injectors.

Fuel leakage can contribute to a fire and/or explosion. Frequently inspect nonmetallic parts of the engines
fuel system and replace if excessive stiffness, deterioration, or fuel leakage is found.
To prevent fire and explosion, perform all service procedures with the engine turned OFF.
Failure to inspect your work could allow fuel leakage to go undetected. This could become a fire or explosion
hazard. After completing service procedures, start engine and check entire fuel system for possible leaks.
To prevent fire and explosion, Volvo Penta fuel system components meet U.S. Coast Guard requirements for
fuel and fuel vapor containment. Do not substitute automotive or other non-approved parts.
Carburetor (GL, GS only)
The carburetor vaporizes fuel and mixes it with air in proper quantities to suit the varying needs of the engine.
Except for changing the carburetor fuel filter screen, the carburetor requires no periodic maintenance or
adjustment. If operational problems occur, see your Volvo Penta dealer.
Electronic fuel injection (Gi, GSi only)
The electronic fuel injection (EFI) fuel metering system delivers the correct amount of fuel to the engine under all
operating conditions. The EFI system is controlled by a microprocessor, and requires no periodic maintenance or
adjustment. If operational problems occur, see your Volvo Penta dealer.

59
Flame arrestor
Remove the flame arrestor every 50 operating hours.
Clean in solvent, air dry, and inspect it for damage.
Replace if damaged.
Reinstall flame arrestor; make sure unit is securely fastened.
To prevent fire and explosion in the engine compartment, the flame
arrestor must always be in place, properly secured, and undamaged.

Electric fuel pumps

Check fuel pumps frequently for signs of fuel leakage. If leakage occurs, have the fuel pump serviced imme-
diately by your Volvo Penta dealer.
EFI engines have two electric fuel pumps:
a low-pressure pump to bring fuel from the boat tank to the engine
a high-pressure pump to supply the fuel injectors.
Both pumps are protected by a single 20-amp fuse. The pumps will operate only when the engine is cranking or
running. If a pump does not function, check the fuses and replace them if necessary. See your Volvo Penta dealer if
further service is required.

Do not run engine out of fuel or run the electric fuel pumps dry more than 20 seconds. Running the electric
fuel pumps dry will damage the fuel pumps.
Fuel filter
All models have a fuel filter in the fuel line before the fuel pump.

IMPORTANT
Volvo Penta EFI engines require a special marine filter with a 5-10 micron filtering capability. Do not substitute
any other type of filter.

Accumulation of water and other fuel contaminants may form corrosive compounds that can damage the fuel
filter, and result in fuel leakage. For this reason, annual replacement of the fuel filter is required to avoid risk
of explosion or fire.
Engine fuel filter replacement

The old fuel filter contains flammable fuel. Dispose of safely.

60
Run the bilge blower for at least five minutes to vent the engine compartment, then start the engine and check
for leakage. Smell for fuel in the bilge. IF YOU CAN SMELL FUEL, TURN THE ENGINE OFF IMMEDIATELY
EXPLOSION AND FIRE ARE AN EXTREME DANGER. Clean up the bilge until fuel cannot be detected by smell.
1. Turn off the engine.
2. Unscrew fuel filter; remove and discard.
3. Lightly lubricate the gasket and inner seal on new fuel filter.
4. Screw on fuel filter and hand-tighten, following instructions on filter.
5. Clean up any spilled fuel.
6. Run the bilge blower for at least five minutes to vent the engine compartment, then start the engine and check for
leakage.
7. Smell for fuel in the bilge.

IF YOU CAN SMELL FUEL, TURN THE ENGINE OFF IMMEDIATELY EXPLOSION AND FIRE ARE AN
EXTREME DANGER.
8. Clean up the bilge until fuel cannot be detected by smell.
Note: A loud whining noise at idle may be due to a restricted fuel filter causing a noisy fuel pump. Operating the engine
with a restricted filter may damage the pressure regulator or fuel pumps. See your Volvo Penta dealer if the pump
makes an unusual noise.
Carburetor fuel filter replacement
1. Turn off the engine.
2. Disconnect the fuel line at the carburetor.
3. Remove the fuel inlet nut, gasket, and screen.
4. Clean the screen with solvent, then allow it to dry.
5. Reinstall the screen, gasket, and fuel inlet nut.
6. Tighten the fuel inlet nut securely.
7. Reconnect the fuel line and tighten it securely.
8. Clean up any spilled fuel.
9. Run the bilge blower for at least five minutes to vent the engine compartment, then start the engine.
10. Smell for fuel in the bilge.

IF YOU CAN SMELL FUEL, TURN THE ENGINE OFF IMMEDIATELY EXPLOSION AND FIRE ARE AN
EXTREME DANGER.
11. Clean up the bilge until fuel cannot be detected by smell.

Electrical system _____________________________________________________________

The engines electrical system features cranking, charging, ignition and trim/tilt circuits. A battery and all necessary
wiring provide power.

61
If electrical connections are reversed, or wires are disconnected when the key switch is ON or the engine is
running, sensitive electrical components may be immediately damaged. Do not turn off the main battery
switch until the engine has stopped.
Battery cables
The following are the minimum specifications for stranded copper cables from the motor to the battery for all models.
The maximum length is 20 feet regardless of cable diameter.

0 to 10 ft. (3.05 m) require a 1/0 AWG (80 MWG) cable

10 to 15 ft. (3.05 to 4.6 m) require a 2/0 AWG (100 MWG) cable
15 to 20 ft. (4.6 to 6.1 m) require a 3/0 AWG (120 MWG) cable

1. Do not use aluminum core battery cables.

2. Failure to use battery cables of recommended gauge and material could result in poor starting and electri-
cal component damage.
Batteries and connections
Note: Whenever you replace your battery, read and understand the information supplied with it before you begin
installation.
1. The engine start battery must be a heavy duty, 12-volt, 650 CCA battery con-
structed for marine use.
2. All other batteries must be heavy duty and constructed for marine use. They can
be either vented/refillable, maintenance-free, or deep-cycle with a CCA or INCA
rating.
3. Use bolts and nuts to secure battery cables to the battery terminals. Do not use
wing nuts to secure battery cables, even if they were supplied with the battery.
4. Tighten all battery connections. Loose battery connections may cause damage
to the engines electrical system.
5. Service electrical components only while the engine is off. Be careful when identifying positive and negative battery
cables and terminals. If you touch the wrong terminal with a battery cable, even briefly, the motors charging
system may be damaged.

The battery terminal connections must always be insulated. If the battery mounting system does not cover the
connections, install protective covers. This will help prevent shorting or arcing at the battery terminals.

1. Do not expose the battery to electrical sparks or an open flame.

2. Do not use jumper cables and a booster battery to start the engine.
62
3. Remove the battery from the boat to recharge. Do not recharge the battery in the boat.
The service life of your battery depends largely on how it is maintained.

Keep batteries dry and clean. Oxidation or dirt on the battery and battery terminals may cause short circuits,
voltage drop, and discharge (especially in damp weather).

Clean battery terminals and leads to remove oxidation.

Tighten cable terminals tightly.

Spray battery terminals and connections with and anti-corrosive agent, or coat them with petroleum jelly.

Check that all other electrical connections are dry and free of oxidation, and that there are not loose connec-
tions.

Always switch off the charging circuit before removing the battery charger connectors.

Inspect your battery at regular intervals for specific gravity (state of charge), individual cell water level, cleanli-
ness and tight, greased connections.

If the battery has become discharged for no apparent reason, check all electrical system components for
malfunction, or a switch left ON, before installing a recharged battery.

Electrolyte levels should be 0.2 0.4 inches (5 10 mm) over the plates in the battery. Top off if necessary,
using distilled water. After topping off, run the engine at fast idle for at least 30 minutes to charge the battery.
Note: Some maintenance-free batteries have special instructions. Make sure to follow them carefully.

Battery electrolyte is a corrosive acid and should be handled with care. If you spill or splash electrolyte on any
part of the body, immediately flush the exposed area with liberal amounts of water and seek medical attention
as soon as possible.
Note: It is important that the battery connections are correct. The negative battery cable must be attached to the
negative terminal () on the battery and the engines positive cable must be attached to the positive terminal (+) on the
battery.

Failure to follow the safety precautions below may result in electrical sparks igniting fuel vapors, and thereby
causing fire or explosion.
1. Operate boats bilge blower for at least 5 minutes. Open engine cover or hatch and check the boats bilge
area for gasoline fumes. If any fumes can be detected by smell, do not operate the boat until the source
can be found, the spill cleaned up, and the cause corrected.
2. Do not connect cables to battery until all other electrical connections have been made.
3. Make sure the ignition switch is OFF before removing or installing electrical equipment, checking any
electrical connections, or installing battery cables.
See your Volvo Penta dealer for recommendations on installing multiple batteries.
Note: When replacing your battery, read and understand the information supplied with it before you begin installation.
63
1. Batteries must be heavy-duty and constructed for marine use. They can be either vented/refillable,
maintenance-free, or deep-cycle with a CCA or MICA rating. Refer to Specifications on pages 95 through 100 for
the correct battery sizes.
2. Use bolts and nuts to secure battery cables to the battery terminals. Do not use wing nuts to secure battery cables,
even if they were supplied with the battery.
3. Loose battery connections can cause damage to the engines electrical system.
4. Service electrical components only while the motor is not running. Be careful when identifying positive and negative
battery cables and terminals. If you touch the wrong terminal with a battery cable, even briefly, the motors charging
system could be damaged.

The battery terminal connections must always be insulated. If the battery mounting system does not cover the
connections, install protective covers. This will help prevent shorting or arcing at the battery terminals.
Engine start battery

IMPORTANT
It is important that the battery connections are correct. The negative battery cable must be attached to the
negative terminal () on the battery, and the engines positive cable must be attached to the positive terminal
(+) on the battery.
Use a 12-volt battery with the following specifications:
a minimum 650 Cold Cranking Amp (CCA) rating at 0 F (-18 C)
165 minutes reserve capacity rating at 89 F (27 C).

Fumes vented during battery charging may cause an explosion.

Do not expose battery to electrical sparks or an open flame.
Do not use jumper cables and a booster battery to start engine.
If the battery compartment is not properly ventilated, remove battery from boat to recharge.
If the battery has become discharged (dead) for no apparent reason, check all electrical system components for
malfunction, or for a switch left in the ON position, before installing a recharged battery.

Failure to follow the safety precautions below may result in electrical sparks igniting fuel vapors causing fire
or explosion.
Operate the boats bilge blower for at least 5 minutes. Open the engine cover or hatch and check the
boats bilge area for gasoline fumes. If any fumes can be detected by smell, do not operate the boat until
you find the source, clean up the spill, and correct the cause.
Do not connect cables to battery until all other electrical connections have been made.

64
 Make sure the ignition switch is OFF before removing or installing electrical equipment, checking any
electrical connections, or installing battery cables.
See your Volvo Penta dealer for recommendations on installing multiple batteries.
Multiple batteries and selector switch
If your boat is equipped with multiple batteries and a selector switch, the engine should be operated with the selector
switch set to the ALL position. This will provide charging system output to all batteries.
A battery isolator is recommended if batteries will be switched for individual operation.
Distributor cap and rotor
Remove, inspect and clean the distributor cap and rotor. Replace these components if worn or damaged with genuine
Volvo Penta parts. No other distributor parts require service or replacement.
Be sure spark plug leads are replaced in the correct firing order (see the table below).
Circuit breakers and fuses
The engine and boats electrical system is protected against current overload by a circuit
breaker and fuses.
If the circuit breaker trips, push its button to reset it.
Replace any blown fuses.

Circuit breakers or fuses that repeatedly fail indicate a problem that requires immediate attention. See your
Volvo Penta dealer.
Note: If electrical connections are reversed, or connections removed when the key switch is on or the engine is
running, the electrical system may be damaged immediately.
Spark plugs
The following table provides spark plug part numbers, spark plug gap, and installation torque:

Spark plugs Spark plug

Engine Model (VP part number) Spark plug gap installation torque Firing order
3.0 GS 3854399 0.045 in. (1.14 mm) 20 ft. lb. (27 Nm) 1342
4.3 GL/Gi 3854399 0.045 in. (1.14 mm) 20 ft. lb. (27 Nm) 165432
5.0 GL 3854399 0.035 in. (0.89 mm) 20 ft. lb. (27 Nm) 18436572
5.0 Gi 3854399 0.045 in. (1.14 mm) 20 ft. lb. (27 Nm) 18436572
5.7 GS 3854399 0.035 in. (0.89 mm) 20 ft. lb. (27 Nm) 18436572
5.7 Gsi 3854399 0.045 in. (1.14 mm) 20 ft. lb. (27 Nm) 18436572
7.4 Gi 3854399 0.045 in. (1.14 mm) 20 ft. lb. (27 Nm) 18436572
7.4 Gsi; 8.2 Gsi 3854400 0.045 in. (1.14 mm) 20 ft. lb. (27 Nm) 18436572
DPX 385/415 3854400 0.045 in. (1.14 mm) 20 ft. lb. (27 Nm) 18436572

Before installing new spark plugs, always check for proper type and gap (see the table above). Incorrect spark plugs
can cause operational problems and possible internal engine damage.
Before installing a spark plug, the spark plug seat in the cylinder head should be wiped clean. Tighten plugs to the
proper torque value (see the table above). Make sure the spark plug terminals are fully seated on the spark plugs.

65
 When spark plug leads are removed, be sure they
are replaced in the correct firing order (see the
table on the previous page).

Avoid abusive handling that could crack the spark plugs ceramic body.
Damaged spark plugs can emit external sparks that could ignite any fuel
vapors in the engine compartment.
Do not operate engine if spark plug boots or high-tension leads are torn
or cracked. This condition could allow external sparks which could ignite 3.0 GS
any fuel vapors in the engine compartment, and result in fire or explo-
sion.
Checking and changing spark plugs
1. Twist and pull only on the spark plug wire boot (pulling on wire may cause 1
2
separation of the core of the wire). 3
4
5
2. Remove spark plugs using a 5/8-inch spark plug socket or a 5/8-inch box 6
wrench. Use care to avoid cracking the spark plug insulators.
1
2 6
3. Carefully inspect the insulators and electrodes of all spark plugs.
3 5
4
Replace any spark plug which has a cracked or broken insulator or which
has loose electrodes.
If the insulator is worn away around the center electrode, or the electrodes 4.3 GL/Gi
are burned or worn, the spark plug is worn out and should be discarded.
Spark plugs that are in good condition, except for carbon or oxide depos-
its, should be thoroughly cleaned and gapped.
The spark plug wires are a special resistance type. The core is carbon-
impregnated linen. This type wire is superior to copper core wire in its resis-
tance to crossfire; however, it is more easily damaged than copper core. For
this reason, pull on the spark plug boots to remove the spark plug wires, rather
than pulling on the wire insulation. If the wire is stretched, the core may be
broken with no evidence of damage on the outer insulation. If the core is
broken, it will cause misfiring. In the case of wire damage, it is necessary to
replace the complete wire assembly since a satisfactory repair cannot be
made. 5.0GL/Gi, 5.7 GS/GSi,
7.4 Gi/GSi, 8.2 GSi
4. Clean ignition wires with a cloth moistened in kerosene, and wipe dry. Bend
wires to check for brittle, cracked or loose insulation. Defective insulation will
permit misfiring, crossfiring, or spark to ground; therefore, defective
wires must be replaced.
5. If the wires are in good condition, clean any terminals that are corroded and replace any that are broken or dis-
torted. Replace any wires with broken or deteriorated cable nipples or spark plug boots.
6. Clean spark plugs.
Spark plugs that have carbon or oxide deposits should be cleaned in a blast type spark plug cleaner. Scraping with a
pointed tool will not properly remove the deposits and may damage the insulator. If spark plugs have a wet or oily
deposit, dip them in a decreasing solvent and dry thoroughly with compressed air. Oily plugs will cause the cleaning
compound to pack in the shell. Carefully follow the instructions of the manufacturer of the cleaner being used. Clean

66
each plug until the interior of shell and entire insulator is cleaned. Avoid excessive blasting.
7. Examine interior of plug in good light. Remove any cleaning compound with compressed air. If traces of carbon or
oxide remain in plug, finish the cleaning with a light blasting operation. Clean firing surfaces of center and side
electrodes with several strokes of a fine cut file.
8. When spark plugs have been thoroughly cleaned, carefully inspect them for cracks or other defects that may not
have been visible before cleaning.
9. Use a round wire feeler gauge to check the gap between the spark plug electrodes. (Flat feeler gauges will not
give a correct measurement if the electrodes are worn.) Adjust gap by bending the side electrode only. Bending the
center electrode will crack the insulator. Setting the spark plug gap to any other specification in an attempt to
improve idle or affect engine performance is not recommended.
10. See the diagrams for correct installation of spark plugs and wires.
For proper engine performance it is very important that the correct spark plugs be used. When installing spark
plugs, make sure that the threads in the cylinder head and all surfaces on plugs and in cylinder heads are clean.
Tighten spark plugs the specified amount. All engines use tapered seat plugs without gaskets.
Do not operate engine if spark plug boots or high-tension leads are torn or cracked. This condition can allow
external sparks, which could ignite any fuel vapors in the engine compartment.
Spark plug wires must be arranged between the distributor cap and spark plugs in the order of firing sequence. If spark
plug wires are not correctly installed, misfiring or crossfiring will result.
Belt adjustments

To prevent possible injury caused by someone inadvertently starting the engine, remove the ignition keys
from each starting location (especially if the engine room/engine compartment cannot be seen from various
remote starting positions such as a flybridge or enclosed cabin).
(3.0 GS, 4.3 Gi, 5.0 Gi, 5.7 GSi, 7.4 Gi/GSi, 8.2 GSi)
These engine models use a serpentine belt, which is a continuous-loop belt threaded through the alternator pulley,
circulating pump pulley, idler pulley, and power steering pump pulley. This single belt replaces three separate belts
(alternator, circulation, and power steering). At least once per year, have your Volvo Penta dealer check the serpentine
belt for wear. An ideal time to have this check performed is when you have the gimbal bearings and universal joints
lubricated.
(4.3 GL, 5.0 GL, 5.7 GS)

Alternator
The belts used for the alternator, water supply pump, and power steering
pulley pump are heavy duty. Do not replace with automotive belts.
(Midpoint)

(Midpoint)
Belt tension
Circulating
pump 1. Belt tension is determined by belt deflection.
pulley
With the engine stopped, the belt should be tight enough so that it will
deflect inch (6 mm) when pressed with a finger, or 75 10 pounds (333.6
44.5 N) when using a belt tension gauge.
If the belt is too tight, excessive belt and bearing wear can occur.
Power steering
pump pulley
If it is too loose, slippage can occur, resulting in belt wear, poor circulating
pump alternator, and power steering operation.
67
2. Belt tension should be checked after 10 hours of service and every 5 hours thereafter.
Alternator belt
With engine OFF, check alternator belt deflection midway between the circulating pump pulley and the alternator pulley.
To increase belt tension:
1. Loosen alternator mounting screws and nuts.
2. Pivot the alternator away from the engine to increase belt tension.
3. While maintaining pressure on the alternator, retighten the top screw and bottom screw and nut.
4. Recheck belt tension.
Idler belt
Note: Improper idler belt adjustment will result in hard steering.
With engine OFF, check idler belt deflection midway between the circulating pump pulley and the idler pump pulley.
To increase belt tension:
1. Loosen pump mounting bracket screws.
2. With a long screwdriver, pry against a corner of the timing chain cover and tab on pump mounting bracket. Never
pry against the pump reservoir or pull filler neck.
3. While maintaining pressure on the bracket, tighten the screw closest to the tab, then tighten the other screws.
4. Recheck belt tension.

Cooling system ______________________________________________________________

Volvo Penta engines have a thermostat-controlled, recirculating type cooling
system.
1. Cool water is drawn in through water intakes located on both sides of
the lower gear case by a raw water pump mounted on the front of the
engine.
2. Water is pumped to the engine and routed by the circulating water pump
through the cooling system.
3. A thermostat inside the engine determines the amount of water to be
taken in, recirculated, and discharged to control the engines operating
temperatures.
Engine overheating
If your engine overheats, the audible alarm will sound and a temperature
gauge on your instrument panel will indicate your engine is overheating.
1. Turn off the engine.
2. Tilt the drive up and look for obstructions to the water intakes (e.g., seaweed, plastic bags).
3. Lower the drive unit.
4. Turn on the engine and run it in NEUTRAL at 1500 RPM.
5. Check the engine gauge to verify condition.
6. If overheating still occurs, return to shore at low RPM (to prevent excessive overheating and engine damage).
7. See your Volvo Penta dealer for service assistance.

68
(Gi, GSi only)
If the engine overheats at high engine speeds, the engine protection mode feature will activate:

Engine speed will automatically be gradually reduced to a maximum of 2500 RPM.

The engine will operate normally only below 2500 RPM.
The engine protection mode feature will remain activated until the engine overheating problem is corrected.

Do not remove the thermostat from the engine, as the engine is likely to overheat.
Draining the cooling system

When temperatures drop below freezing, failure to completely drain the cooling system will result in serious
damage to the engine and exhaust manifolds. To assure complete drainage, probe all drain openings with a
piece of wire to remove any blockage.

IMPORTANT
The following steps are very important in protecting your engine from damage in freezing conditions. If you
are unsure of how to perform any of the following steps, see your Volvo Penta dealer for a complete
end-of-season/winterization service. Freeze damage to the engine package is not covered by your Volvo Penta
limited warranty.
Perform these procedures with the boat out of the water. It will prevent damage to cooling system compo-
nents if temperatures drop below freezing.
When draining the engine, raise or lower the bow of the boat to position the engine in a level attitude. This
will provide for complete drainage of the block and manifold. If the bow of the boat is higher or lower than
the stern, some water may be trapped in the block.
Engine raw water cooled
1. (3.0 only) Open the manifold drain cock.
(4.3, 5.0, 5.7, 7.4, 8.2, DPX 385/415 only) Remove water hose clamps and hoses from the exhaust manifold.
2. Open the engine block drain cocks.
(On 4.3 only, also open the open intake manifold drain plug located on the front face of the intake manifold, directly
above the circulating pump.)
3. (4.3/5.0/7.4 Gi, 5.7 GSi, 7.4/8.2 GSi, DPX 385/415 only) Remove the water hose clamps and water hoses from the
vapor separator tank.
4. After all of the water has drained out, reattach hoses/caps, tighten clamps, and close all drain cocks.
Engine fresh water cooled (if equipped)
1. Check the coolant level and antifreeze concentration (check antifreeze manufacturers instructions). Make sure the
antifreezes freeze point is adequate for expected temperatures.
2. Open the drain cock on the raw water side of the heat exchanger.
3. (3.0 only) Open the manifold drain cock.

69
 (4.3, 5.0, 5.7, 7.4, 8.2, DPX 385/415 only) Remove water hose clamps and hoses/rubber caps from the exhaust
manifolds.
4. After all of the water has drained out, reattach hoses/caps, tighten clamps, and close all drain cocks.
Raw water pump
1. Loosen and slide clamps back.
2. Remove hoses from the rear of water pump and drain.
3. Crank the engine no more than 2 seconds (DO NOT START) to expel any water trapped in water pump.
4. Reattach water pump hoses and tighten clamps.

Do not reverse water pump hoses. Serious engine damage may result.
Oil cooler
Remove the lower water hose from the oil cooler. If cooler is mounted horizontally, remove either hose, loosen mount-
ing bolt, and tip open end of cooler down to drain.

Steering system _____________________________________________________________

1. Check steering and throttle cables for cracks and wear. Check all along the length of the
cable, as shown in the diagram. Replace the cables if you suspect that they are not in optimum
condition.
2. Check steering system hoses for cracks, leaks, and
wear. Replace any hoses that you suspect are not in
optimum condition.
3. (DPX only) Check steering system hydraulic hoses for
cracks, leaks, and wear. Replace any hoses that you
suspect are not in optimum condition.

Power trim/tilt fluid level

The power trim and tilt assembly contains an electric motor, hydraulic pump, and reser-
voir.
At the beginning of each boating season, check the fluid level in the reservoir:
1. With the drive unit trimmed in as far as possible, remove the fill cap.
2. Check the fluid level. It should be between the minimum and maximum marks on the
reservoir. If needed, add Volvo Penta DuraPlus Power Trim/Tilt and Steering Fluid.
3. Replace the fill cap and tighten securely.
Steering reservoir fluid level
Whenever you check the engine oil, also remove the steering reservoir dipstick and check the fluid level. Wipe the
dipstick and note the hot and cold fluid levels. If needed, add Volvo Penta DuraPlus Power Trim/Tilt and Steering
Fluid. Do not overfill the pump reservoir.

70
Never fill the steering system with an oil of unknown quality. Non-recommended oil may cause steering
operation impairment, or component damage.
Do not allow contaminants to enter the reservoir when checking or filling the oil level.
Primary shaft spline and bearing lubrication
The primary universal joint shaft splines and bearings must be lubricated each year and whenever the drive unit is
removed. This procedure requires the removal of the drive unit; therefore, your Volvo Penta dealer should do it. An
ideal time to have this done is during the winterization process. Failure to have primary shaft splines and bearings
lubricated each year may result in damage to the drive unit.
Tie rod (twin installations only)
Check the rod connecting the drive units, particularly if you hit an obstacle. If the tie rod is bent, loose, or damaged,
have it serviced immediately by your Volvo Penta dealer. In the meantime, operate your boat at slow speeds only.

The tie bar is an integral part of the steering system and is a vital safety part. A damaged tie rod may hinder
steering operation or render it completely ineffective. Always replace a damaged tie bar. Never try to
straighten or weld a damaged tie rod.

Engine and drive service ______________________________________________________

You may lubricate your Volvo Penta sterndrive yourself, or you may have your Volvo Penta dealer perform this service
for you.
If you lubricate the sterndrive yourself:
Instructions for SX drive unit lubrication are located on page 73.
Instructions for DP drive unit lubrication are located on page 74.
Instructions for DPX drive unit lubrication are located on page 75.
If you have your Volvo Penta dealer lubricate the sterndrive, make sure to take it to your dealer at the required inter-
vals, as outlined in your maintenance schedule on page 55.

Lubrication system ___________________________________________________________

Engine/crankcase oil
To obtain the best engine performance and engine life, Volvo Penta recommends DuraPlus. Premium engine oil
labeled for Service CE/SG, or you may use an engine oil with the recommended quality and viscosity. Engine oils are
specified by API service, letter designations and SAE viscosity numbers. Refer to oil identification symbol on the
container.
Initial factory fill is a high quality motor oil for API Service CE/SG. During the break-in period (20 hours), frequently
check the oil level. Somewhat higher oil consumption is normal until piston rings are seated. The oil level should be
maintained between the ADD and FULL marks on the dipstick. The space between the marks represents approxi-
mately one quart (one liter). For oil level dipstick location, refer to the photographs on pages 22 through 31.
See the Specifications on pages 95 through 100, and the Maintenance Schedule on page 55 for oil filter type and
service intervals.
When you add or change engine oil, use Volvo Penta engine oils for gasoline engines. Use the following chart to select

71
the SAE viscosity that matches the temperature range in which you expect to operate.

SAE Viscosity Chart

Lowest Anticipated Recommended SAE
Temperature Viscosity Oils
SAE 30*
32 F (0 C) above SAE 20W/50
SAE 15W/50
0 F (-18 C) 32 F (0 C) SAE 20W-20
Below 0 F (-18 C) SAE 10W

*SAE 30 Volvo Penta DuraPlus Synthetic Motor Oil (P/N 3851230-7) (U.S. and Canada Only)
Use single viscosity oils in markets where available. The use of multi-viscosity oils such as 10W-30, 10W-40 is not
recommended unless single viscosity oils are not available.
At the end of the break-in period (20 hours), change the crankcase oil and replace the oil filter. Refer to the Mainte-
nance Schedule on page 55 for recommended oil change intervals.

Never use parts that are not recommended specifically for marine use. Substituting automotive or generally
supplied parts and hardware may result in product malfunction and possible injury to the operator and/or
passengers. Never use parts of unknown quality.
Checking engine oil level
Remove the dipstick. The oil level must be between the two marks on the dipstick. Add oil as necessary to maintain the
proper level.
Note: Do not allow the crankcase oil level to go below the ADD mark, and do not fill above the FULL mark. Overfilling
results in high operating temperatures, foaming (air in oil), loss of power, and overall reduced engine life.
Changing engine oil
Engine oil and the oil filter are important factors affecting engine life. They affect ease of starting, fuel economy,
combustion chamber deposits, and engine wear. Drain and refill the engine crankcase once each season or every 100
operating hours, whichever comes first. (Also see the maintenance schedule.)
1. Run the engine to warm the crankcase oil (for easier removal).
2. Turn off the engine.
3. Remove oil dipstick, and drain the oil from the crankcase through the dipstick tube, using the special fitting pro-
vided on the tube. This special fitting is provided so that the oil does not have to be drained into the bulge.
4. Withdraw oil with a suction pump.
Note: You may purchase either a manual or an electric suction pump from any marine supply store, or from your
Volvo Penta dealer.
5. Dispose of used oil according to any applicable federal, state, and local environmental regulations.
6. Replace the oil filter.
7. Remove the oil fill cap and fill the crankcase to the specified capacity with Volvo Penta DuraPlus premium engine
oil.

72
Changing the oil filter
Replace the oil filter whenever the engine oil is changed. This filter is a self-contained, screw-on type.
1. To remove, unscrew filter canister counter-clockwise. Dispose of used filter according to any applicable federal,
state, and local environmental regulations.
2. When attaching a new filter, be sure the gasket is lightly lubricated with motor oil.
3. Hand-tighten only.
4. Run engine and check for leaks. (Do not run engine out of water.)
Drive components ____________________________________________________________
The drive unit is filled at the factory with Volvo Penta DuraPlus GL 5 Synthetic Gear Lube.
Drive unit lubrication
Lubricating the drive unit (SX)
Adding lubricant
Every week check the oil level in the drive unit (if possible, without removing the
boat from the water).

Fully thread the oil dipstick into the oil level hole in the drive unit to properly
check the oil level. An improper oil level may result in serious drive unit
damage.
Fully thread the dipstick into the hole, then remove and check the oil level.
Make sure that the oil level comes to
the top of the flattened portion of the
dipstick.
The oil should be amber-colored.
The oil will appear milky if any moisture is present.
No metal flakes should appear in the oil.
If moisture or metal flakes appear in the drive unit oil, take the boat to your
Volvo Penta dealer.
If the oil level is low, add only enough lubricant to bring the oil level within
the full range of the dipstick.
You should completely drain and refill the drive unit at least once per season.
Draining the drive unit (SX)
1. Place the drive unit in the run (down) position. Put a container under the drive unit to catch the draining oil.
2. Remove the oil drain plug and the oil level dipstick.
3. Allow the drive unit to drain completely. Dispose of
used oil according to applicable environmental regula-
tions.
Filling the drive unit (SX)
1. Remove the three screws securing the rear cover to
access the oil level plug.
2. Remove the oil level plug.
3. Fill the drive unit with Volvo Penta DuraPlus GL 5
73
 Synthetic Gear Lube. Fill through the oil drain plug location. Fill slowly to purge air. The drive unit is properly filled
when the oil appears at the oil level plug hole.
4. When filled to the proper level, install the oil level dipstick and oil level plug first (to prevent excessive oil loss), then
the oil drain plug.
5. Tighten oil level and drain plugs securely.
6. Install the rear cover and tighten screws securely.
If you cannot fill the drive unit through the oil drain plug, you can fill the drive by trimming it up a few degrees and filling
it through the oil level plug. Reinstall the oil level plug, and place the drive in the run (down) position. Remove the
dipstick and check the oil level. Reinstall the dipstick and tighten securely.
Check the oil level with the dipstick (oil must appear on the full range of the dipstick). Add oil if required through the
dipstick hole. Refer to Specifications on pages 95 through 100 for drive unit oil capacity.
If the drive unit was filled through the oil level plug, wait 15 minutes before checking the oil level with the dipstick.
Leave the dipstick loose during the waiting period. This will help ensure all air is purged from the oil cavity.
Lubricating the drive unit (DP-S)
The drive unit is filled at the factory with Volvo Penta DuraPlus GL5 Synthetic gearcase lubricant. This lubricant must
be used when adding lubricant or refilling the drive unit.
Adding lubricant

Fully thread the oil dipstick into the oil level hole in the drive unit to properly check the oil level. An improper
oil level may result in serious drive unit damage.
Each week, check the oil level in the drive unit (if possible, without removing the boat from the water).
Make sure that the oil level comes to the top of the flattened portion of the dipstick.
The oil should be amber-colored.
The oil will appear milky if any moisture is present.
No metal flakes should appear in the oil.
If moisture or metal flakes appear in the drive unit oil, take the boat to your Volvo Penta
dealer.
If the oil level is low, add only enough lubricant to bring the oil level within the full range
of the dipstick. Improper oil level may result in serious damage to the drive unit.
You should completely drain and refill the drive unit at least once per season.
Draining the drive unit (DP-S)
1. Place drive unit in the run (down) position.
2. Remove propellers and mounting hardware.
Note: Special tools are required to remove Duoprop propellers. Refer to Propeller care on
page 77.
3. Remove the oil drain plug and the oil level dipstick.
4. Allow the drive unit to drain completely. Dispose of used oil according to applicable
environmental regulations.

74
Filling the drive unit (DP-S)
1. Remove the three screws securing the rear cover to
access the oil level plug.
2. Remove the oil level plug.
3. Fill the drive unit with Volvo Penta DuraPlus GL 5
Synthetic Gear Lube. Fill through the oil drain plug
location. Fill slowly to purge air. The drive unit is properly
filled when the oil appears at the oil level plug hole.
4. When filled to the proper level, install the oil level
dipstick and oil level plug first to prevent excessive oil loss, then the oil drain plug.
5. Tighten the oil level and drain plugs securely.
Note: If unable to fill the drive unit through oil drain plug, fill the drive trimming it up a few degrees and filling through
the oil level plug.
6. Reinstall the oil level plug, and place the drive in the run (down) position. Remove the dipstick and check the oil
level. Reinstall the dipstick and tighten securely.
7. Install the propellers (refer to Propeller care on page 77).
8. Install the rear cover and tighten screws securely.
9. Check the oil level with the dipstick (oil must appear on the full range of dipstick). Add oil, if required, through the
dipstick hole. Refer to Specifications on pages 95 through 100 for drive unit lubricant capacity.
Note: If the drive unit was filled through the oil level plug, wait 15 minutes before checking oil with the dipstick. This will
help ensure all air is purged from the oil cavity. Leave the dipstick loose during the waiting period.
Lubricating the drive unit (DPX)
The drive unit is filled at the factory with Volvo Penta DuraPlus GL5 Synthetic gearcase lubricant. This lubricant must
be used when adding lubricant or refilling the drive unit.
Adding lubricant
Each week, check the oil level in the drive unit (if possible, without removing the boat
from the water).

Fully thread the oil dipstick into the oil level hole in the drive unit to properly
check the oil level. An improper oil level may result in serious drive unit damage.
Make sure that the oil level comes to the top of the flattened portion of the dipstick.
The oil should be amber-colored.
The oil will appear milky if any moisture is present.
No metal flakes should appear in the oil.
If moisture or metal flakes appear in the drive unit oil, take the boat to your Volvo Penta
dealer.
If the oil level is low, add only enough lubricant to bring the oil level within the full range of the dipstick. Improper oil
level may result in serious damage to the drive unit.
You should completely drain and refill the drive unit at least once per season.
Draining the drive unit (DPX)
1. Place the drive unit in the run (down) position and remove the dipstick.
2. Remove the propellers.
3. Remove the oil drain plug at the bottom of the propeller gear housing.

75
4. Allow the drive unit to drain completely, then replace the drain plug. If the oil shows signs of water, contact your
Volvo Penta dealer for service assistance.
5. Dispose of used oil according to any applicable environmental regulations.
Filling the drive unit (DPX)
6. To fill the drive unit, remove the rear cover and the oil fill plug. (Refer to
Specifications on pages 95 through 100 for drive unit oil capacity.)
7. Tilt the drive unit up.
8. Fill the drive with Volvo Penta DuraPlus GL5 Synthetic gearcase lubricant.
9. When filled to the proper level, install the oil fill plug and tighten it securely.
10. Lower the drive and check the oil level with the dipstick.
11. If necessary, add oil through the dipstick hole.
12. Make sure the fill and drain plug seals are not leaking.
13. Install the rear cover and tighten screws securely.
External lubrication points
The gimbal bearing and universal joints must be lubricated each year. This procedure requires the removal of the drive
unit; therefore, your Volvo Penta dealer should do it. An ideal time to have this done is during the winterization process.
Failure to have the gimbal bearing and universal joints lubricated each year may result in damage to the pivot housing
and drive unit.
Anodes (sacrificial anodes)
Sacrificial anodes are attached to the bottom of the gimbal
housing and at the front of the gearcase above the
anti-ventilation plate. (On the DPX drive only, there are addi-
tional anodes at the back of the intermediate housing, and on
the steering cylinders.)
Anodes are slowly eroded away by galvanic action and require
inspection. Additionally, anodes that are subjected to frequent
wetting and drying require periodic scraping with coarse emery
cloth or sandpaper to remove scale and oxidation to maintain their effectiveness. Do not
paint anodes, as this will destroy their effectiveness.
When you need to replace the anodes, see your Volvo Penta dealer. The material
composition of Volvo Penta anodes meets U.S. Military Specification 18001-H. If you use
other anodes, make sure they have equivalent specifications or galvanic corrosion
protection will be lost.
You may order the anodes separately, or as part of an accessories kit. (The accessories
kit also includes o-rings, oils, washers, seals, and bellows.)
Replacing sacrificial anodes
1. Inspect anodes every 14 days, or more frequently if used in extremely salty water. If an anode is 2/3 its original size
(1/3 eroded), replace it.
Note: If you use a stainless steel propeller, additional sacrificial anodes may be required to handle the added corrosion
potential.
2. Remove the two screws holding the anodes onto the gearcase and/or the gimbal housing. Set the screws aside,
as you will use them again.
3. Pull off the old anode.
4. Insert the new anode.

76
5. Secure with two screws.
6. Tighten screws to these torque specifications:
12 14 ft. lb. (16 19 Nm) for the gimbal housing anode

60 84 in. lb. (6.8 9.5 Nm) for the gearcase anode

If additional electronic or electrical equipment is installed, each item should have an individual anode or grounding
device and all grounding devices must be interconnected. Follow equipment manufacturers recommendations.
Note: When your boating is done mostly in fresh water, Volvo Penta recommends replacing zinc anodes with magne-
sium anodes.
Active corrosion protection system
Your boat may be equipped with an optional Volvo Penta active corrosion
protection system that greatly improves the life of the drive unit by protecting
it from corrosion. This system operates with very little current drain from the
boats electrical system. It keeps the voltage potential in the area around the
drive unit in a range that is not corrosive to aluminum. (This is accomplished
by changing the charge of water molecules so that they do not remove
electrons from the drive units metal parts to cause corrosion.) If you do not
have an active corrosion protection system already installed, you may
purchase one from your authorized Volvo Penta dealer.
The protection systems control box has a small LED indicator light that
blinks once every one to five seconds to show the system is operating properly.
If the light blinks at the rate of once every five seconds, the demand for protection is very low.
If the light is flashing once per second, the demand for protection is high and the system is operating at maximum
capacity.
The Volvo Penta active corrosion protection system is designed to adequately protect one drive unit from galvanic
corrosion.
Note: This system will not provide protection from stray currents emitted by a malfunctioning AC power source on your
boat, the pier, or other boats in close proximity to yours. Although the zinc sacrificial anodes will last much longer with
this system, they must still be cleaned and checked for material condition periodically.

Propeller care _______________________________________________________________

A damaged or unbalanced propeller will cause excessive vibration and a loss of boat speed. Under
these conditions, stop the engine and check the propeller for damage. If the propeller appears
damaged, have it checked by your Volvo Penta dealer. Always carry a spare propeller and replace
the damaged propeller as soon as possible.
A rubber hub in the propeller is the shock absorber that minimizes damage to drive unit and
engine. If the rubber hub should begin to slip, it can be easily replaced at an authorized Volvo
Penta dealer or propeller service station.

Protect your hands from the sharp edges of the propeller blades. Wear gloves whenever you remove or
replace a propeller.
Do not attempt to hold propellers by hand when you remove or install propellers and propeller nuts. Serious
injury could result.

77
Never continuously run with a damaged propeller. Running with a damaged propeller can result in drive unit
and engine damage.
Propeller replacement SX
Removing the propeller
1. Ignition switch must be OFF.
2. Make sure the remote control is in NEUTRAL.
3. Remove the cotter pin and keeper.
4. Shift the remote control into FORWARD to lock the
propeller shaft.
5. Remove the propeller nut using a 1-1/16 wrench.
6. Remove the thrust washer, propeller, and thrust bushing.
7. Wipe the propeller shaft clean. Inspect for fishing line;
remove if present.
Installing the propeller

Failure to install all components could result in loss of the propeller and damage to the drive unit the next
time the boat is operated.
1. Ignition switch must be OFF.
2. Make sure the remote control is in NEUTRAL.
3. Coat the full length of the propeller shaft with Volvo Penta propeller shaft grease. (Removal of the propeller will be
difficult if this is not done.)
4. Place the thrust bushing on the propeller shaft with the inner taper toward the gearcase to match the taper on the
propeller shaft.
5. Install the propeller onto the propeller shaft, aligning splines, and push the propeller onto the thrust bushing until
the splines are exposed.
6. Install the thrust washer on propeller shaft splines.
7. Shift the remote control into REVERSE gear to lock the propeller shaft.
8. Install and tighten the propeller nut until it is seated against the thrust washer.
9. Loosen the nut, then turn it back against the thrust washer until finger tight. Tighten the nut an additional 1/3 to 1/2
turn.
10. Index the keeper on the propeller nut until it is aligned with the cotter pin hole.
11. Install the cotter pin and bend the ends to secure (use a new cotter pin if necessary).
12. Shift the remote control into NEUTRAL. The propeller should turn freely.
Before your next outing, use a torque wrench to tighten the propeller to 70 80 ft. lb. (96 108 Nm). The thrust
washer, nut, keeper, and cotter pin must be installed as shown.
78
Propeller replacement DP-S
Removing the propeller
This procedure requires you to use a special tool, Volvo Penta
P/N 3855516.
1. Ignition switch must be OFF.
2. Make sure the remote control is in FORWARD to lock the
propeller shaft.
3. Remove the rear propeller nut.
4. Remove the rear propeller.
5. Change the remote control position to REVERSE to lock the propeller shaft.
6. Remove the front propeller nut.
7. Remove the front propeller.
8. Wipe the propeller shaft clean. Inspect for fishing line; remove if present.
Installing the propeller

Failure to install all components could result in loss of the propeller and damage to the drive unit the next
time the boat is operated.
1. Ignition switch must be OFF.
2. Make sure the remote control is in FORWARD.
3. Coat the full length of the propeller shaft with Volvo Penta propeller shaft grease. (Removal of the propeller will be
difficult later if this precaution is not done.)
4. Install the front propeller.
5. Install the front propeller nut and tighten it to 45 ft. lb. (60 Nm).
6. Shift the remote control into REVERSE to lock the propeller shaft.
7. Install the rear propeller.
8. Install the rear propeller nut and tighten it to 50 ft. lb. (70 Nm).
9. Shift the remote control into NEUTRAL. The propeller should turn freely.

79
Propeller replacement DPX
Removing the propeller
This procedure requires you to use a special tool kit, Volvo
Penta P/N 885195.
1. Ignition switch must be OFF.
2. Make sure the remote control is in FORWARD to lock the
propeller shaft.
3. Use the special tool (as shown) to remove the rear locking
screw. Use a 30-mm socket to remove the propeller
locking nut.
4. Remove the rear propeller.
5. Shift the remote control into REVERSE to lock the propel-
ler shaft.
6. Use the special tool (as shown) to remove the front
locking screw.
7. Remove the front propeller.
8. Wipe the propeller shaft clean. Inspect for fishing line; remove if present.
Installing the propeller

Failure to install all components may result in loss of the propeller and damage to the drive unit the next time
the boat is operated.
1. Ignition switch must be OFF.
2. Coat the full length of both propeller shafts with Volvo Penta propeller shaft grease. (It will be difficult to remove
propellers later if this precaution is not done.)
3. Make sure the remote control is in FORWARD to lock the propeller shaft.
4. Install the front propeller.
5. Install the front propeller locking nut. Use the special tool to tighten the nut to 37 52 ft. lb. (50 70 Nm).
6. Shift the remote control into REVERSE to lock the propeller shaft.
7. Install the rear propeller.
8. Install the rear propeller locking nut (use a 30-mm socket). Tighten the nut to 19 26 ft. lb. (25 35 Nm).
9. Install the locking screw. Use the special tool to tighten the nut to 52 59 ft. lb. (70 80 Nm).
10. Shift the remote control into NEUTRAL. The propeller should turn freely.
Boat bottom _________________________________________________________________
The condition of the boats bottom can affect your boats performance. Marine growth, present in fresh water as well as
salt water, will reduce boat speed. A boat bottom with evidence of marine growth can cause a reduction in top speed of
20 percent or more. Periodically clean the bottom of your boat following the manufacturers recommendations. Bottom
painting may also be desirable.

Engine alignment ____________________________________________________________

Because of the special tools required, a Volvo Penta dealer must do the engine alignment. This should be done during
off-season storage preparations.

80
Failure to periodically check engine alignment may result in premature failure of the engine coupler.
Replacement parts ___________________________________________________________

Improper parts substitution can result in fire or explosion.

Use genuine Volvo Penta parts when replacement parts needed. Volvo Penta replacement parts are de-
signed to meet USCG requirements and ABYC standards for marine applications.
Failure to use genuine Volvo Penta parts may result in product malfunction and possible injury to the
operator and/or passengers.
In your Volvo Penta product, certain fuel and electrical system components
have been designed to comply with U.S. Coast Guard regulations. Parts or
components that comply with these regulations are designed so they will not
emit fuel vapors or cause ignition of fuel vapors in the engine compartment.
To prevent explosion or fire, do not substitute automotive or general hard-
ware parts for the following:
Circuit breakers, alternator, and related wiring
Starter and related wiring
Distributor, distributor cap, spark plugs, high tension leads, and related
ignition parts
Fuel pumps, relays, filter, and related parts
Rubber caps (manifold), hoses (water and exhaust), and attaching clamps
Fuel injector O-rings, injector fuel line pressure relief valve and caps, fuel reservoir vent hose and cover
gasket, high pressure fuel pump mounting O-rings, fuel pressure regulator, and fuel rails
Your Volvo Penta product was designed to operate in a marine environment. This can involve operating
at high RPM for long periods
in salt or brackish water
in water laden with silt and minerals
Substituting automotive or generally supplied parts and hardware may result in product malfunction and possible injury
to the operator and/or passengers. Never use parts of unknown quality. See your Volvo Penta dealer. You can depend
on him to furnish expert service and Volvo Penta parts.

Bottom painting ______________________________________________________________

If your boat is in water where marine growth is a problem, using an antifouling paint may reduce the growth rate. Be
aware of laws that may limit your paint choice and its use.
A pure Teflon-based agent is recommended.
Copper-based antifouling paint may be used. Do not paint transom shield or drive with copper-based
paint. If you do use copper-based paint on your boat bottom, leave a 1-inch border between the paint
and the transom shield.
Vinyl-butyl base antifouling paint is a recommended alternative.
See your Volvo Penta dealer for an EPA-approved antifouling paint suitable for your area.
81
Engine submersion ___________________________________________________________
1. Remove the engine from the water as quickly as possible.
2. Contact your local Volvo Penta dealer for service.
Your dealer will need to drain all water from the engine and immediately relubricate all internal parts.
All electrical devices must also be dried and inspected for water damage.
3. Frequently check engine compartment for gasoline fumes and excessive water accumulation. In addition, make
sure that the water depth in the bilge is kept well below the flywheel housing.

Delay in completing the above actions may result in extensive engine damage.

82
 TROUBLESHOOTING CHECKLIST

The following troubleshooting checklist gives some of the most common problems and their solutions. If your problem
does not appear on this checklist, please contact your Volvo Penta dealer.

After following the Action described in the chart, and before cranking the engine, make sure there are no
loose electrical connections that could spark. Make sure the engine compartment is free of fuel vapors.
FAILURE TO DO SO MAY RESULT IN FIRE AND/OR EXPLOSION.

Sympton Possible cause Action

No fuel in tank or gasoline
Fill tank or open valve.
shutoff valve closed
Check fuel supply for water
Water in fuel supply or contamination. If gasoline is old or if
Engine cranks but won't start
gasoline is old. water is present, drain fuel tank and
flush with fresh gasoline, and change
Fuel system problem. See your Volvo Penta dealer.
Emergency stop switch. Reinstall lanyard.
Fuel system problem. See your Volvo Penta dealer.
Replace filters. See your Volvo Penta
Engine runs erratically Fuel filters.
dealer.
Electrical system problem. See your Volvo Penta dealer.
Check for damaged propellers.
Check for bent propeller shaft.
Engine vibrates Propeller condition.
Look for weeds on propeller or gear
case.
Boat overloaded. Reduce or redistribute load.
Drain bilge according to Federal, State,
Water in bilge.
Loss of engine performance and local regulations.
Boat hull condition. Clean boat hull.
Incorrect fuel octane. Fill gas tank with proper fuel.
Remote control box or shift
High shift effort See your Volvo Penta dealer.
cable.

83
84
 PROBLEM RESOLUTION

Your satisfaction with our products and dealer services is vital. Volvo Penta takes pride in producing durable, reliable
products, and a strong dealer network supports our efforts. If you have questions about service or your products
performance, your Volvo Penta dealer will be happy to answer them. There may be times, though, that, in spite of the
best intentions, differences develop between a boat owner and a dealer. If this happens to you, Volvo Penta and your
dealer will work together to pursue a reasonable resolution.
If you have a problem with your Volvo Penta product:
Maintain a written record of events (the problem, related conversations/with whom, important dates, etc.), as well as
any supporting documents (invoices, work orders, etc.). Then, take the following steps:
1. Discuss the matter with the proper department manager at the dealership (e.g., Service Manager, Parts Manager,
etc.). Explain exactly what caused the problem and ask what action will be taken.
If the matter remains unresolved after a reasonable amount of time:
2. Discuss the matter with the Dealer Principal (usually the owner or co-owner of the dealership). Explain what took
place in step 1.
If the matter is not resolved within a reasonable amount of time:
3. Contact the Consumer Affairs Department at:

Volvo Penta of the Americas, Inc. Volvo Penta Canada

1300 Volvo Penta Drive 75 West 3rd Avenue
Chesapeake, VA 23320 Vancouver, BC V5Y 3T8
Phone: (757) 436-5100 Phone: (604) 872-7511
Fax: (757) 436-5153 Fax: (604) 872-4606
Please be prepared to provide the following information:
Your name, address, and daytime telephone number.
The Volvo Penta product model and serial number for each major component in the power package (engine,
transom shield, drive, or transmission). Check your owners manual for the serial number plate location.
Date of purchase.
Current engine operating hours.
Selling and/or Servicing Dealers name.
Description of the problem.

85
86
 SPECIFICATIONS

Note: Volvo Penta of the Americas, Inc., reserves the right to make changes in weight, construction, materials, or
specifications without notice or obligation.

3.0 GS ______________________________________________________________________
Battery size 12 volt with 360 Cold Cranking Amp (CCA) rating
Bore and stroke 4.00 x 3.60 inches (101.60 x 91.44 mm)
Carburetor Adjustable idle circuit
Fixed main fuel jets
Electric choke
Charging system 65 amp alternator, with internal transistorized voltage regulator
Cooling system Variable volume pump on engine
Recirculating pump on engine
Thermostatically controlled temperature
Cylinders (number) 4 in-line
Displacement 181 cubic inches (3.0 liters)
Firing order 1342
Fuel filter (in fuel pump) Volvo Penta P/N 3855104
Fuel filter location Refer to photographs on pages 22 through 23.
Fuel type Inside the U.S.: 89 octane (AKI) unleaded gasoline
Outside the U.S.: 93 octane (RON) unleaded gasoline
Full throttle operating range 4200 4600 RPM
Idle RPM (fixed) 600 750 RPM in forward gear
Ignition timing Authorized Volvo Penta dealer service only
Oil capacity
Engine Without filter: 3.5 quarts (3.3 liters)
With filter: 4 quarts (3.8 liters)
Drive unit Approximately 2.2 quarts (2.1 liters)
Oil filter Volvo Penta P/N 835440
Oil filter location Refer to photographs on pages 22 through 23.
Oil type
Engine DuraPlus Premium engine oil labeled for API service CE/SG
Drive unit DuraPlus GL 5 synthetic gear lube
Power steering fluid DuraPlus power steering fluid
Spark plugs Volvo Penta P/N 3854399
Spark plug gap 0.045 inches (1.14 mm)
Spark plug installation torque 20 ft. lb. (27 Nm)

87
4.3 GL/Gi ___________________________________________________________________
Battery size 12 volt with 360 Cold Cranking Amp (CCA) rating
Bore and stroke 4.000 x 3.480 in. (101.60 x 88.39 mm)
Carburetor (GL) Adjustable idle circuit
Fixed main fuel jets
Electric choke
Charging system 65 amp alternator, with internal transistorized voltage regulator
Cooling system Variable volume pump on engine
Recirculating pump on engine
Thermostatically controlled temperature
Cylinders (number) 90 V-6
Displacement 262 cubic inches (4.3 liters)
Firing order 165432
Fuel filter Volvo Penta P/N 3852413
Fuel filter location Refer to photographs on pages 24 through 27.
Fuel type Inside the U.S.: 89 octane (AKI) unleaded gasoline
Outside the U.S.: 93 octane (RON) unleaded gasoline
Full throttle operating range 4200 4600 RPM
Idle RPM GL: 550 650 RPM in forward gear
Gi: 600 RPM
Ignition timing Authorized Volvo Penta dealer service only
Oil capacity
Engine Without filter: 4 quarts (3.8 liters)
With filter: 4.5 quarts (4.3 liters)
Drive unit SX: approximately 2.2 quarts (2.1 liters)
DP: approximately 2.5 quarts (2.4 liters)
Oil filter Volvo Penta P/N 841750
Oil filter location Refer to photographs on pages 24 through 27.
Oil type
Engine DuraPlus Premium engine oil labeled for API service CE/SG
Drive unit DuraPlus GL 5 synthetic gear lube
Power steering fluid DuraPlus power steering fluid
Spark plugs Volvo Penta P/N 3854399
Spark plug gap 0.045 inches (1.14 mm)
Spark plug installation torque 20 ft. lb. (27 Nm)

88
5.0 GL/Gi ___________________________________________________________________
Battery size 12 volt with 650 Cold Cranking Amp (CCA) rating
Bore and stroke 3.740 x 3.480 inches (95.00 x 88.39 mm)
Carburetor (GL) Adjustable idle circuit
Fixed main fuel jets
Electric choke
Charging system 65 amp alternator, with internal transistorized voltage regulator
Cooling system Variable volume pump on engine
Recirculating pump on engine
Thermostatically controlled temperature
Cylinders (number) 90 V-8
Displacement 305 cubic inches (5.0 liters)
Firing order 18436572
Fuel filter Volvo Penta P/N 3852413
Fuel filter location Refer to photographs on pages 24 through 27.
Fuel type Inside the U.S.: 89 octane (AKI) unleaded gasoline
Outside the U.S.: 93 octane (RON) unleaded gasoline
Full throttle operating range GL: 4400 4800 RPM
Gi: 4600 5000 RPM
Idle RPM (fixed) GL: 4400 4800 RPM
Gi: 600 RPM
Ignition timing Authorized Volvo Penta dealer service only
Oil capacity
Engine Without filter: 5 quarts (4.7 liters)
With filter: 6 quarts (5.7 liters)
Drive unit SX: approximately 2.2 quarts (2.1 liters)
DP: approximately 2.5 quarts (2.4 liters)
Oil filter Volvo Penta P/N 3850559
Oil filter location Refer to photographs on pages 24 through 27.
Oil type
Engine DuraPlus Premium engine oil labeled for API service CE/SG
Drive unit DuraPlus GL 5 synthetic gear lube
Power steering fluid DuraPlus power steering fluid
Spark plugs Volvo Penta P/N 3854399
Spark plug gap GL 0.35 inches (0.89 mm)
Gi 0.045 inches (1.14 mm)
Spark plug installation torque 20 ft. lb. (27 Nm)

89
5.7 GS/GSi __________________________________________________________________
Battery size 12 volt with 650 Cold Cranking Amp (CCA) rating
Bore and stroke 4.000 x 3.480 inches (101.60 x 88.39 mm)
Carburetor (GS) Adjustable idle circuit
Fixed main fuel jets
Electric choke
Charging system 65 amp alternator, with internal transistorized voltage regulator
Cooling system Variable volume pump on engine
Recirculating pump on engine
Thermostatically controlled temperature
Cylinders (number) 90 V-8
Displacement 350 cubic inches (5.7 liters)
Firing order 18436572
Fuel filter Volvo Penta P/N 3852413
Fuel filter location Refer to photographs on pages 24 through 27.
Fuel type Inside the U.S.: 89 octane (AKI) unleaded gasoline
Outside the U.S.: 93 octane (RON) unleaded gasoline
Full throttle operating range GS: 4400 4800 RPM
GSi: 4600 5000 RPM
Idle RPM (fixed GS: 550 650 RPM in forward gear
GSi: 600 RPM
Ignition timing Authorized Volvo Penta dealer service only
Oil capacity
Engine Without filter: 5 quarts (4.7 liters)
With filter: 6 quarts (5.7 liters)
Drive unit SX: approximately 2.2 quarts (2.1 liters)
DP: approximately 2.5 quarts (2.4 liters)
Oil filter Volvo Penta P/N 3850559
Oil filter location Refer to photographs on pages 24 through 27.
Oil type
Engine DuraPlus Premium engine oil labeled for API service CE/SG
Drive unit DuraPlus GL 5 synthetic gear lube
Power steering fluid DuraPlus power steering fluid
Spark plugs Volvo Penta P/N 3854399
Spark plug gap GS 0.035 inches (0.89 mm)
GSi 0.045 inches (1.14 mm)
Spark plug installation torque 20 ft. lb. (27 Nm)

90
7.4 Gi/GSi; 8.2 GSi____________________________________________________________
Battery size 12 volt with 650 Cold Cranking Amp (CCA) rating
Bore and stroke 4.250 x 4.000 inches (107.95 x 101.60 mm)
Charging system 65 amp alternator, with internal transistorized voltage regulator
Cooling system Variable volume pump on engine
Recirculating pump on engine
Thermostatically controlled temperature
Cylinders (number) 90 V-8
Displacement 454 cubic inches (7.4 liters)
Firing order 18436572
Fuel filter Volvo Penta P/N 3852413
Fuel filter location Refer to photographs on pages 28 through 29.
Fuel type Inside the U.S.: 89 octane (AKI) unleaded gasoline
Outside the U.S.: 93 octane (RON) unleaded gasoline
Full throttle operating range Gi: 4200 4600 RPM
GSi: 4800 5200 RPM
Idle RPM (fixed) 600 RPM
Ignition timing Authorized Volvo Penta dealer service only
Oil capacity
Engine Without filter: 8 quarts (7.5 liters)
With filter: 9 quarts (8.5 liters)
Drive unit SX: approximately 2.2 quarts (2.1 liters)
DP: approximately 2.5 quarts (2.4 liters)
Oil filter Volvo Penta P/N 3850559
Oil filter location Refer to photographs on pages 28 through 29.
Oil type
Engine DuraPlus Premium engine oil labeled for service CE/SG
Drive unit DuraPlus GL 5 synthetic gear lube
Power steering fluid DuraPlus power steering fluid
Spark plugs 7.4 Gi Volvo Penta P/N 3854399
7.4, 8.2 GSi Volvo Penta P/N 3854400
Spark plug gap 0.045 inches (1.14 mm)
Spark plug installation torque 20 ft. lb. (27 Nm)

91
DPX 385; DPX 415 ____________________________________________________________
Battery size 12 volt with 650 Cold Cranking Amp (CCA) rating
Bore and stroke DPX 385: 4.250 x 4.000 inches (107.95 x 101.60 mm)
DPX 415: 4.468 x 4.000 inches (113.49 x 101.60 mm)
Charging system 65 amp alternator, with internal transistorized voltage regulator
Cooling system Variable volume pump on engine
Recirculating pump on engine
Thermostatically controlled temperature
Cylinders (number) 90 V-8
Displacement DPX 385: 454 cubic inches (7.4 liters)
DPX 415: 502 cubic inches (8.2 liters)
Firing order 18436572
Fuel filter Volvo Penta P/N 3852413
Fuel filter location Refer to photographs on pages 30 through 31.
Fuel type Inside the U.S.: 89 octane (AKI) unleaded gasoline
Outside the U.S.: 93 octane (RON) unleaded gasoline
Full throttle operating range DPX 385: 4800 5200 RPM
DPX 415: 4600 5000 RPM
Idle RPM (fixed) 600 RPM
Ignition timing Authorized Volvo Penta dealer service only
Oil capacity
Engine Without filter: 8 quarts (7.5 liters)
With filter: 9 quarts (8.5 liters)
Drive unit Approximately 2.06 quarts (2.0 liters)
Oil filter Volvo Penta P/N 3850559
Oil filter location Refer to photographs on pages 30 through 31.
Oil type
Engine DuraPlus Premium engine oil labeled for service CE/SG
Drive unit DuraPlus GL 5 synthetic gear lube
Power steering fluid DuraPlus power steering fluid
Spark plugs Volvo Penta P/N 3854400
Spark plug gap 0.045 inches (1.14 mm)
Spark plug installation torque 20 ft. lb. (27 Nm)

92
 APPENDIX A: CERTIFIED ENGINES AND BSO NUMBERS

Certified engines _____________________________________________________________

The following information concerns engines certified for European use on Lake Constance and in Switzerland.
All Volvo Penta engines and products have been developed on the basis that they should have as little an impact on
the environment as possible. However, national and regional environmental legislation is different for all the markets
where Volvo Penta sells its products. Sometimes legislation determines that we have to build special engines, or that
the engine must be approved in advance and certified by the authorities.
The fact that the engine is certified means that Volvo Penta, as the engine manufacturer, ensures that all the engines it
manufactures meet the sample engine approved for certification. Certification does not just cover requirements with
respect to factory-new engines: Certified engines already in operation must also be able to meet environmental re-
quirements. Certain requirements with respect to servicing and spare parts must be met in order that Volvo Penta as
engine manufacturer will be able to assume responsibility for engines in operation.
Volvo Penta does not advise you against carrying out service yourself. In fact, Volvo Penta views it as an advantage
because you have the opportunity to find out quickly whether any components are not working or are working abnor-
mally. However, special expertise, service manuals, special tools and other suitable equipment are required in order to
be able to perform some service checks. Only an authorized Volvo Penta service dealer must carry out these service
checks. Always contact your Volvo Penta dealer if you are unsure of anything to do with your engines function or
maintenance.
Those of you who own or maintain a certified Volvo Penta engine must be aware of the following:
Service intervals and maintenance by Volvo Penta must be adhered to.
Only Volvo Penta genuine parts intended for certified engine may be used.
An authorized Volvo Penta service dealer must always service the ignition system (ignition timing) and the fuel
injection system.
The engine must not be rebuilt or in any way modified, with the exception of the accessories and serviceable units
developed for the engine by Volvo Penta.
Changes to the installation of exhaust pipes and intake air ducts to the engine compartment (ventilation ducts)
must not be implemented, as this may affect exhaust emissions.
Unauthorized personnel must not break any seals present.
Note: Use only Volvo Penta genuine parts when you need spare parts. Using non-genuine parts means that AB Volvo
Penta can no longer assume responsibility for an engine meeting the certified design. Volvo Penta will not assume any
responsibility for any kind of damage or costs due to non-genuine Volvo Penta service parts being used for the product
in question.

Bodensee Shiffahrts Ordnung (BSO) number _____________________________________

Your engine may have an assigned Bodensee Shiffahrts Ordnung (BSO) number. A BSO number is assigned to an
engine model when it is certified for European use on Lake Constance and in Switzerland. There are two BSO certifi-
cation decals placed on the engine, one on the starboard high-rise bracket and the other on the front of the port
cylinder head to verify engine certification. These decals must be maintained so engine certification can be verified in
the future.
When an emissions check is required, the plug located on either high-rise elbow can be removed for installation of a
test probe.

93
94
7797286-TX English 03-2000