Seat PDF

SEAT BELT FRONT PASSENGER SEAT BELT WARNING LIGHT (for Sedan) SB1
FRONT PASSENGER SEAT BELT WARNING LIGHT (for

SEAT BELT
RESTRAINTS
Sedan)
COMPONENTS
HAZARD WARNING SIGNAL

SWITCH CONNECTOR SB
INSTRUMENT CLUSTER
CENTER FINISH PANEL
SUB-ASSEMBLY
for Integrated with Panel:
x4
RADIO RECEIVER
ASSEMBLY
INSTRUMENT CLUSTER
FINISH PANEL
INSTRUMENT PANEL
FINISH PANEL END RH
INSTRUMENT PANEL
FINISH PANEL END LH
INSTRUMENT PANEL LOWER

CENTER FINISH PANEL
B138696E01
SB2 SEAT BELT FRONT PASSENGER SEAT BELT WARNING LIGHT (for Sedan)
INSTRUMENT PANEL CENTER

SB REGISTER ASSEMBLY

SWITCH ASSEMBLY (Built in Front
Passenger Seat Belt Warning Light)
w/ Radio Receiver:
INSTRUMENT PANEL CENTER

REGISTER ASSEMBLY

SWITCH ASSEMBLY (Built in Front
Passenger Seat Belt Warning Light)
B138572E01
SEAT BELT FRONT PASSENGER SEAT BELT WARNING LIGHT (for Sedan) SB3
REMOVAL
1. DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
2. REMOVE INSTRUMENT PANEL LOWER CENTER
FINISH PANEL (See page ME-138)
3. REMOVE INSTRUMENT PANEL FINISH PANEL END
RH (See page ME-138) SB
LH (See page ME-138)
5. REMOVE INSTRUMENT CLUSTER FINISH PANEL
(See page ME-139)
6. REMOVE RADIO RECEIVER ASSEMBLY (for
Integrated with Panel) (See page AV-38)
7. REMOVE INSTRUMENT CLUSTER CENTER FINISH
PANEL SUB-ASSEMBLY (except Integrated with
Panel) (See page IP-43)
8. REMOVE INSTRUMENT PANEL CENTER REGISTER
ASSEMBLY (See page LI-166)
9. REMOVE HAZARD WARNING SIGNAL SWITCH
ASSEMBLY (Built in Front Passenger Seat Belt
Warning Light)
(a) Disengage the 3 claws and remove the hazard
warning signal switch.
B138529
INSPECTION
1. INSPECT HAZARD WARNING SIGNAL SWITCH
Warning Light)
(a) Check the operation.
(1) Apply battery voltage to the terminals and
Battery check that the indicator illuminates.
Standard
B134920E01 Condition Standard
Positive battery - Terminal 6 (lG+)
Illuminates
Negative battery - Terminal 8 (PBEW)
If the result is not as specified, replace the

hazard warning signal switch.
SB4 SEAT BELT FRONT PASSENGER SEAT BELT WARNING LIGHT (for Sedan)
INSTALLATION
1. INSTALL HAZARD WARNING SIGNAL SWITCH
Warning Light)
(a) Engage the 3 claws and install the hazard warning
signal switch.
2. INSTALL INSTRUMENT PANEL CENTER REGISTER
SB ASSEMBLY (See page LI-168)
3. INSTALL RADIO RECEIVER ASSEMBLY (for
Integrated with Panel) (See page AV-40)
4. INSTALL INSTRUMENT CLUSTER CENTER FINISH
PANEL SUB-ASSEMBLY (except Integrated with
Panel) (See page IP-56)
B138529
5. INSTALL INSTRUMENT CLUSTER FINISH PANEL

(See page ME-140)
6. INSTALL INSTRUMENT PANEL FINISH PANEL END
RH (See page ME-141)
LH (See page ME-141)
8. INSTALL INSTRUMENT PANEL LOWER CENTER
FINISH PANEL (See page ME-142)
9. CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL
Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)
SEAT BELT FRONT PASSENGER SEAT BELT WARNING LIGHT (for Hatchback) SB5
FRONT PASSENGER SEAT BELT WARNING LIGHT (for

SEAT BELT
RESTRAINTS
Hatchback)
COMPONENTS
SB
FRONT PASSENGER
SEAT BELT WARNING
LIGHT CONNECTOR
FRONT PASSENGER SEAT

BELT WARNING LIGHT
INSTRUMENT PANEL
FINISH PANEL END
B117689E01
SB6 SEAT BELT FRONT PASSENGER SEAT BELT WARNING LIGHT (for Hatchback)
REMOVAL
TERMINAL
(See page ME-145)
3. REMOVE FRONT PASSENGER SEAT BELT
SB WARNING LIGHT
(a) Disengage the 2 claws and remove the front
passenger seat belt warning light.
B114416
INSPECTION
1. INSPECT FRONT PASSENGER SEAT BELT
WARNING LIGHT
(a) Check the operation.
(1) Apply battery voltage to the terminals and
check that the indicator illuminates.
Standard
Battery Condition Standard
B126913E01 Positive battery - Terminal 6 (IG+)
Illuminates
Negative battery - Terminal 3 (PBELT)
If the result is not as specified, replace the front

passenger seat belt warning light.
INSTALLATION
1. INSTALL FRONT PASSENGER SEAT BELT WARNING
LIGHT
(a) Engage the 2 claws and install the front passenger
seat belt warning light.
(See page ME-149)
B114416
TERMINAL
SEAT BELT SEAT BELT WARNING SYSTEM SB7
SEAT BELT WARNING SYSTEM

SEAT BELT
RESTRAINTS
PARTS LOCATION
HATCHBACK:
COMBINATION METER ASSEMBLY

SB
W/O TACHOMETER:
FRONT DRIVER SEAT BELT

WARNING LIGHT
W/ TACHOMETER: FRONT PASSENGER SEAT BELT

WARNING LIGHT
CENTER AIRBAG SENSOR

ASSEMBLY
MAIN BODY ECU

(INSTRUMENT PANEL J/B)
- GAUGE FUSE
B143853E02
SB8 SEAT BELT SEAT BELT WARNING SYSTEM
SEDAN:
COMBINATION METER ASSEMBLY
W/O TACHOMETER:
SB
FRONT DRIVER SEAT BELT WARNING LIGHT

FRONT PASSENGER SEAT BELT
W/ TACHOMETER: WARNING LIGHT
FRONT DRIVER SEAT BELT WARNING LIGHT
CENTER AIRBAG
SENSOR ASSEMBLY
MAIN BODY ECU

(INSTRUMENT PANEL J/B)
- GAUGE FUSE
B143851E01
REAR OCCUPANT CLASSIFICATION

SENSOR RH
FRONT OCCUPANT CLASSIFICATION SENSOR RH
OCCUPANT CLASSIFICATION ECU

SB
FRONT OCCUPANT
CLASSIFICATION
SENSOR LH
REAR OCCUPANT
FRONT SEAT INNER BELT CLASSIFICATION
ASSEMBLY RH SENSOR LH
FRONT SEAT INNER BELT
ASSEMBLY LH
B118460E01
SYSTEM DIAGRAM
Front Driver Seat Belt

SB Warning Light
Combination Meter Assembly
Instrument Panel Finish
Panel End RH*1
Seat Belt Warning Buzzer for Driver

Side and Passenger Side
Front Passenger Seat Belt

Warning Light
Hazard Warning Signal

Main Body ECU Switch Assembly*2
CAN Communication Line
Front Passenger Seat Belt

Center Airbag Sensor Assembly Warning Light
Front Seat Inner Belt Front Seat Inner Belt

Occupant Classification ECU
Assembly LH Assembly RH
Occupant Classification
Sensors (Front Passenger
Side) *1: Hatchback
*2: Sedan
B143852E01
Communication table:
Sender Receiver Signal Line
Front seat inner belt switch signal
Center airbag sensor assembly Main body ECU CAN communication line
(driver side)
Sender Receiver Signal Line

Center airbag sensor assembly Main body ECU CAN communication line
(passenger side)
Main body ECU Combination meter assembly CAN communication line
(driver side)
Main body ECU Combination meter assembly CAN communication line
(passenger side)
SB
SYSTEM DESCRIPTION
1. SEAT BELT WARNING SYSTEM DESCRIPTION
If a seat belt is not fastened, this system flashes the seat
belt warning light and sounds the seat belt warning
buzzer as a reminder.
2. FUNCTIONS OF MAIN COMPONENTS
Components Function
SB Front Seat Inner Belt Assembly LH
Informs center airbag sensor assembly of front driver seat belt
condition (fastened or unfastened)
Informs occupant classification ECU of front passenger seat belt
Front Seat Inner Belt Assembly RH
Informs center airbag sensor assembly of front passenger seat
condition (occupied or unoccupied)
Informs center airbag sensor assembly of front passenger seat belt
Informs occupant classification ECU of front passenger seat condition
Occupant Classification Sensor
(occupied or unoccupied)
Informs combination meter assembly of front driver and front
passenger seat belt condition (fastened or unfastened)
Main Body ECU
Informs combination meter assembly of front passenger seat
condition (occupied or unoccupied)
If front driver seat belt is unfastened and ignition switch is ON,
Front Driver Seat Belt Warning Light combination meter assembly flashes seat belt warning light of
combination meter assembly as reminder
Hatchback: When front passenger seat is occupied and ignition switch
is ON, if passenger seat belt is unfastened, combination meter
assembly flashes front passenger seat belt warning light of instrument
panel finish panel end RH as reminder
Front Passenger Seat Belt Warning Light
Sedan: When front passenger seat is occupied and ignition switch is
ON, if passenger seat belt is unfastened, combination meter assembly
flashes front passenger seat belt warning light of hazard warning
signal switch assembly as reminder
If front driver or front passenger seat belt is unfastened and ignition
Seat Belt Warning Buzzer for Front Driver Side and Front Passenger
switch is ON, combination meter assembly sounds buzzer as
Side
reminder
3. SYSTEM OPERATION
When the ignition switch is ON, this system detects
the condition of the seat belts based on signals from
the front seat inner belt switches (for driver and front
passenger seats) and the occupant classification
sensor (front passenger side only).
HOW TO PROCEED WITH

TROUBLESHOOTING
HINT:
Use these procedures to troubleshoot the seat belt
warning system.
*: Use the intelligent tester.
SB
1 VEHICLE BROUGHT TO WORKSHOP
NEXT
2 INSPECT BATTERY VOLTAGE
Standard voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery
before proceeding.
NEXT
3 CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
(a) Use the intelligent tester to check if the CAN

communication system is functioning normally.
Result:
Result Proceed to
DTC is not output A
DTC is output B
B GO TO CAN COMMUNICATION SYSTEM
4 PROBLEM SYMPTOMS TABLE
Result:
Result Proceed to
Fault is not listed in problem symptoms
A
table
Fault is listed in problem symptoms
B
table
B Go to step 6
5 OVERALL ANALYSIS AND TROUBLESHOOTING*
(a) DATA LIST / ACTIVE TEST (see page SB-20)

(b) TERMINALS OF ECU (see page SB-14)

NEXT
6 REPAIR OR REPLACE
NEXT
SB
7 CONFIRMATION TEST
NEXT
END
CUSTOMIZE PARAMETERS
HINT:
The following item can be customized.
Display (Item) Default Function Setting
Changes seat belt warning
SEAT BELT WARN D/P ON D/P ON / D ON / P ON / D/P OFF
buzzer setting
NOTICE: SB
When the customer requests the modification of a
function, first make sure that the function(s) can be
customized.
Record the current settings before customizing.
When troubleshooting a function, first make sure that
the function is not set to OFF.
PROBLEM SYMPTOMS TABLE

HINT:
Use the table below to help determine the causes of the
problem symptom. The potential causes of the symptoms are
listed in order of probability in the "Suspected Area" column
of the table. Check each symptom by checking the suspected
areas in the order they are listed. Replace parts as
SB Seat belt warning system
necessary.
Symptom Suspected area See page

Front seat inner belt assembly LH (for Hatchback) SB-40
Front seat inner belt assembly LH (for Sedan) SB-34
Wire harness SB-22
Front driver seat belt warning light does not operate
Center airbag sensor assembly SB-22
Main body ECU SB-22
Combination meter assembly SB-22
Fuse SB-24
Front passenger seat belt warning light (for Hatchback) SB-6
Front passenger seat belt warning light (for Sedan) SB-3
Front seat inner belt assembly RH (for Hatchback) SB-40
Front seat inner belt assembly RH (for Sedan) SB-34
Front passenger seat belt warning light does not
Occupant classification sensor RS-226
operate
Wire harness SB-24
Occupant classification ECU SB-24
Center airbag sensor assembly SB-24
Main body ECU SB-24
Combination meter assembly SB-24
Seat belt warning buzzer does not sound (Front driver Combination meter assembly (for Hatchback) ME-73
and front passenger seat belt warning lights operate
normally) Combination meter assembly (for Sedan) ME-10
TERMINALS OF ECU
1. COMBINATION METER ASSEMBLY
Hatchback:
D2 D1
SB

B127205E04
Sedan:
D76 D1

E126885E06
(a) Disconnect the D1 combination meter assembly

connector.
(b) Measure the voltage and resistance of the wire
harness side connector.
Standard
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
D1-1 - Body ground B - Body ground Ignition switch signal Ignition switch OFF ON Below 1 V 11 to 14 V
D1-2 - Body ground L - Body ground Battery Always 11 to 14 V
D1-24 - Body ground BR - Body ground Ground Always Below 1
If the result is not as specified, there may be a

malfunction in the wire harness.
(c) Reconnect the combination meter assembly
connector.
(d) Measure the voltage of the wire harness side
connector.
Standard voltage
Pulse generation
D1-20 - Body ground G - Body ground CAN communication line Ignition switch ON
(See waveform 1)
Pulse generation
D1-21 - Body ground W - Body ground CAN communication line Ignition switch ON
(See waveform 2)
Ignition switch ON
Seat belt warning light
Front passenger seat is Alternating between 11 to
D2-9*1 - Body ground O - Body ground signal (Front passenger
occupied and its seat belt 14 V and below 1 V
side)
is unfastened
Ignition switch ON
Front passenger seat is
D2-9*1 - Body ground O - Body ground signal (Front passenger Below 1 V
occupied and its seat belt
side)
is fastened
Ignition switch ON
Front passenger seat is Alternating between 11 to
D76-9*2 - Body ground O - Body ground signal (Front passenger
occupied and its seat belt 14 V and below 1 V
side)
is unfastened
Ignition switch ON
Front passenger seat is
D76-9*2 - Body ground O - Body ground signal (Front passenger Below 1 V
occupied and its seat belt
side)
is fastened
SB *1: Hatchback
*2: Sedan
If the result is not as specified, the combination
meter may have a malfunction.
(e) Waveform 1 (Reference): Using an oscilloscope
CAN communication signal
1 V/DIV. Terminal Name D1-21 (CANL) - D1-24 (ET)
Tester Range 1V/DIV, 10s/DIV
Condition Ignition switch ON
GND
10 sec./DIV.
A086154E11
(f) Waveform 2 (Reference): Using an oscilloscope

CAN communication signal
1 V/DIV.
Terminal Name D1-21 (CANL) - D1-24 (ET)
Tester Range 1V/DIV, 10s/DIV
Condition Ignition switch ON
2. CENTER AIRBAG SENSOR ASSEMBLY

GND
10 sec./DIV.
A086155E12
Center Airbag Sensor Assembly:

D16 J8 J9
B148514E01
Terminal No. Terminal Symbol Destination

D16-13 CANH CAN communication line
D16-21 IG2 IGN fuse
D16-22 CANL CAN communication line
D16-25 E1 Ground
D16-26 E2 Ground
J8-11 DBE+ Front seat inner belt assembly LH
J8-12 DBE- Front seat inner belt assembly LH
J9-12 FSP+ Occupant Classification ECU
Terminal No. Terminal Symbol Destination

J9-13 FSP- Occupant Classification ECU
3. OCCUPANT CLASSIFICATION ECU
Occupant Classification ECU: U1 J24
SB
H100909E04
(a) Disconnect the J24 occupant classification ECU

connector.
(b) Measure the voltage and resistance of the wire
harness side connector.
J24-7 (IG) - J24-3 (GND) O - W-B Power source (IG2 Fuse) Ignition switch OFF Below 1 V
J24-7 (IG) - J24-3 (GND) O - W-B Power source (IG2 Fuse) Ignition switch ON 11 to 14 V
Power source (ECU-B
J24-1 (+B) - Body ground V - Body ground Always 11 to 14 V
Fuse)
J24-3 (GND) - Body
W-B - Body ground Ground Always Below 1
ground
If the result is not as specified, there may be a

malfunction in the wire harness.
(c) Reconnect the occupant classification ECU
connector.
(d) Measure the voltage of the connector.
BSW (J24-9) - BGND Passenger side buckle Buckle switch ON
O-P Pulse generation
(J24-5) switch line Buckle switch OFF
Center airbag sensor
FSR+ (J24-8) - FSR- (J24-
GR - Y assembly communication Ignition switch ON Pulse generation
4)
line
If the result is not as specified, the combination

meter may have a malfunction.
DIAGNOSIS SYSTEM
CG SG CANH SIL 1. CHECK DLC3
(a) The ECU uses ISO 15765-4 for communication.
The terminal arrangement of the DLC3 complies
with SAE J1962 and matches the ISO 15765-4
format.
CANL BAT
H100769E16
Symbols (Terminal No.) Terminal Description Condition Specified Condition

SIL (7) - SG (5) Bus " +" line During transmission Pulse generation
CG (4) - Body ground Chassis ground Always Below 1
Symbols (Terminal No.) Terminal Description Condition Specified Condition

SG (5) - Body ground Signal ground Always Below 1
BAT (16) - Body ground Battery positive Always 11 to 14 V
CANH (6) - CANL (14) CAN bus line Ignition switch OFF* 54 to 69
CANH (6) - CG (4) HIGH-level CAN bus line Ignition switch OFF* 200 or higher
CANL (14) - CG (4) LOW-level CAN bus line Ignition switch OFF* 200 or higher
CANH (6) - BAT (16) HIGH-level CAN bus line Ignition switch OFF* 6 k or higher
SB CANL (14) - BAT (16) LOW-level CAN bus line Ignition switch OFF* 6 k or higher
NOTICE:
*: Before measuring the resistance, leave the
vehicle as is for at least 1 minute and do not
operate the ignition switch, any other switches
or the doors.
If the result is not as specified, the DLC3 may have
a malfunction. Repair or replace the harness and
connector.
HINT:
Hatchback: Connect the cable of the intelligent tester to the
Intelligent Tester CAN VIM, connect the CAN VIM to the DLC3, turn
the ignition switch ON and attempt to use the tester.
If the display indicates that a communication error
has occurred, there is a problem either with the
vehicle or with the tester.
DLC3 If communication is normal when the tester is
CAN VIM
connected to another vehicle, inspect the DLC3
of the original vehicle.
If communication is still not possible when the
tester is connected to another vehicle, the
Intelligent Tester
problem is probably in the tester itself. Consult
Sedan:
the Service Department listed in the tester's
instruction manual.
2. INSPECT BATTERY VOLTAGE
Standard voltage:
DLC3 11 to 14 V
CAN VIM If the voltage is below 11 V, recharge or replace the
battery before proceeding.
B133416E01
3. INSPECT FRONT DRIVER SEAT BELT WARNING
LIGHT
(a) Turn the ignition switch ON.
(b) When the driver seat belt is not fastened, check that
the combination meter assembly driver seat belt
warning light blinks.
(c) When the seat belt is fastened, check that the
combination meter assembly driver side seat belt
warning light turns off.
4. INSPECT FRONT PASSENGER SEAT BELT
WARNING LIGHT
(b) When the front passenger seat is occupied, but the

seat belt is not fastened, check that the front
passenger seat belt warning light on the instrument
panel finish panel end RH*1 or hazard warning
signal switch assembly*2 blinks.
*1: Hatchback
*2: Sedan
(c) When the front passenger seat belt is fastened,
check that the front passenger seat belt warning SB
light turns off.
5. INSPECT SEAT BELT WARNING BUZZER USING
DRIVER SEAT BELT
(b) When the driver seat belt is not fastened within 1.8
seconds of the ignition switch being turned ON,
check that the seat belt warning buzzer sounds at
1.2 second intervals for 6 seconds.
(c) When the driver seat belt is not fastened within 13.8
seconds of the ignition switch being turned ON and
the vehicle speed reaches 12.4 mph (20 km/h) or
more, check that the buzzer sounds at 1.2 second
intervals for 9.6 seconds.
(d) After the buzzer has sounded for 9.6 seconds,
check that the buzzer sounds at 0.4 second
intervals for a further 20 seconds.
(e) When 29.6 seconds have elapsed since the buzzer
started sounding in step (c) above, check that the
buzzer stops sounding.
(f) After the buzzer has stopped sounding, turn the
ignition switch OFF and then start the engine again.
With the driver seat belt unfastened, drive the
vehicle at 12.4 mph (20 km/h) or more. Check that
the buzzer sounds.
(g) After the buzzer has stopped sounding, fasten the
driver seat belt, drive the vehicle at 12.4 mph (20
km/h) or more, and then unfasten the seat belt.
Check that the buzzer sounds.
(h) After the buzzer has stopped sounding, move the
shift lever to R. Then move the shift lever to D (for A/
T only). With the driver seat belt unfastened, drive
the vehicle at 12.4 mph (20km/h) or more. Check
that the buzzer sounds.
6. INSPECT SEAT BELT WARNING BUZZER USING
FRONT PASSENGER SEAT BELT
HINT:
If the following inspection is conducted by one person,
since the front passenger seat belt warning buzzer
function uses signals from the occupant classification
sensors, place an object with a weight of 36 kg (79.37 lb)
or more on the front passenger seat.
(b) When the front passenger seat belt is not fastened

within 1.8 seconds of the ignition switch being
turned ON, check that the seat belt warning buzzer
sounds at 1.2 second intervals for 6 seconds.
(c) When the front passenger seat belt is not fastened
within 13.8 seconds of the ignition switch being
turned ON and the vehicle speed reaches 12.4 mph
(20 km/h) or more, check that the buzzer sounds at
SB 1.2 second intervals for 9.6 seconds.
(d) After the buzzer has sounded for 9.6 seconds,
check that the buzzer sounds at 0.4 second
intervals for a further 20 seconds.
(e) When 29.6 seconds have elapsed since the buzzer
started sounding in step (c) above, check that the
buzzer stops sounding.
(f) After the buzzer has stopped sounding, turn the
ignition switch OFF and then start the engine again.
With the front passenger seat belt unfastened, drive
the vehicle at 12.4 mph (20 km/h) or more. Check
that the buzzer sounds.
(g) After the buzzer has stopped sounding, fasten the
front passenger seat belt, drive the vehicle at 12.4
mph (20 km/h) or more, and then unfasten the front
passenger seat belt. Check that the buzzer sounds.
(h) After the buzzer has stopped sounding, move the
shift lever to R. Then move the shift lever to D. With
the front passenger seat belt unfastened, drive the
vehicle at 12.4 mph (20km/h) or more. Check that
the buzzer sounds.
DATA LIST / ACTIVE TEST

1. READ DATA LIST
HINT:
By accessing the DATA LIST using the intelligent tester,
values of the switches and sensors can be read without
removing any parts. Reading the DATA LIST is the first
step of troubleshooting and is one method of shortening
labor time. SB
(a) Connect the intelligent tester with the CAN VIM to
the DLC3.
(b) Turn the ignition switch ON and turn the tester ON.
(c) Enter the DATA LIST by following the prompts
displayed on the tester screen.
Center Airbag Sensor Assembly
Measurement Item/ Range
Item Normal Condition Diagnostic Note
(Display)
Buckle switch (Driver side)/
UNSET: Seat belt not fastened
D BUCKLE SW UNSET/SET -
SET: Seat belt fastened
NG: Data not determined
Buckle switch (Passenger side)/
UNSET: Seat belt not fastened
P BUCKLE SW UNSET/SET -
SET: Seat belt fastened
NG: Data not determined

Measurement Item/ Range
(Display)
Buckle switch (Front passenger
side)/
UNSET: Front passenger side
seat belt is unfastened
SET: Front passenger side seat
belt is fastened
NG: Front passenger side seat
belt is malfunctioning
Front passenger classification/
AF05: Adult (36 to 54 kg (79.37 to
119.05 lb)) is seated
AM50: Adult more than 54 kg
(119.05 lb) is seated
CHILD: Child (less than 36 kg
PASSENGER CLASS (79.37 lb)) is seated AF05/AM50/CHILD/CRS/OFF -
CRS: Child restraint system (less
than 7 kg (15.43 lb)) and front
passenger side buckle switch is
ON, then 7 to 36 kg (15.43 to
79.37 lb) is set
OFF: Vacant
2. PERFORM ACTIVE TEST

HINT:
Performing the intelligent tester's ACTIVE TEST allows
relays, VSV, actuators and other items to be operated
without removing any parts. Performing the ACTIVE
TEST early in troubleshooting is one way to save time.
The DATA LIST can be displayed during the ACTIVE
TEST.
(a) Connect the intelligent tester with the CAN VIM to
the DLC3.
(c) Enter the ACTIVE TEST by following the prompts
displayed on the tester screen.
Combination Meter Assembly:
Item Test Details Diagnostic Note
Front driver seat belt warning light / OFF or
D-BELT REMIND -
ON
Front passenger seat belt warning light / OFF
SB P-BELT REMIND
or ON
-
Driver Side Seat Belt Warning Light does not Operate

DESCRIPTION
When the ignition switch is ON, the center airbag sensor assembly communicates the status of the front
seat inner belt assembly LH to the main body ECU using the CAN communication line. The main body
ECU receives signals from the center airbag sensor assembly and transmits them to the combination
meter assembly. When the seat belt is unfastened, the combination meter assembly flashes the driver
seat belt warning light in the combination meter assembly. When the seat belt is fastened, the SB
combination meter assembly stops flashing the front driver seat belt warning light.
WIRING DIAGRAM
Front Seat Inner Belt

Assembly LH Center Airbag Sensor Assembly Combination Meter Assembly
LBE+
DBE+ CPU
CANH CANH
CANL CANL
DBE-
LBE-
Seat Belt Warning Light
(Driver Side)
Main Body ECU
CAN Communication Line
CANH
CANL
B119959E01
INSPECTION PROCEDURE
1 CHECK SUPPLEMENTAL RESTRAINT SYSTEM
(a) Connect the intelligent tester with the CAN VIM to the
DLC3.
(c) Enter the following menus: DIAGNOSIS / SRS AIRBAG/

DTC INFO
Result
Result Proceed to
No SRS DTCs are output A
SRS DTCs are output B
SB B GO TO SUPPLEMENTAL RESTRAINT
SYSTEM
2 PERFORM ACTIVE TEST BY INTELLIGENT TESTER (D-BELT REMIND)
DLC3.
(c) Enter the following menus: DIAGNOSIS / METER /
ACTIVE TEST
Front driver seat belt warning light / OFF
D-BELT REMIND -
or ON
OK:
Front driver seat belt warning light comes on.
OK REPLACE MAIN BODY ECU
NG
REPLACE COMBINATION METER ASSEMBLY

Front Passenger Side Seat Belt Warning Light Malfunction

DESCRIPTION
When the ignition switch is ON and the front passenger seat is occupied, the center airbag sensor
assembly communicates the status of the front seat inner belt assembly RH to the main body ECU using
the CAN communication line. The main body ECU receives signals from the center airbag sensor
assembly and transmits them to the combination meter assembly. When the seat belt is unfastened, the
combination meter assembly flashes the front passenger seat belt warning light on the instrument panel SB
finish panel end RH*1 or hazard warning signal switch assembly*2. When the seat belt is fastened, the
combination meter assembly stops flashing the front passenger seat belt warning light on the instrument
panel finish panel end RH*1 or hazard warning signal switch assembly*2.
HINT:
*1: Hatchback
*2: Sedan
WIRING DIAGRAM
Occupant Classification ECU Front Seat Inner Belt Assembly RH
Occupant Classification SVC1 SVC1

Sensor (Front LH) BSW RBE+
SB SIG1 SIG1
SGD1 SGD1 BGND RBE-
Sensor (Front RH)
SIG2 SIG2
SVC4 SVC4 Occupant Classification
SGD2 SGD2
Sensor (Rear RH)
SIG4 SIG4
Sensor (Rear LH) SGD4 SGD4
SIG3 SIG3
SGD3 SGD3
FSR+ FSR-
Main Body ECU
FSP+ FSP-
CANH CANH
Center Airbag CANL CANL
Sensor Assembly
Combination Meter
Assembly
GAUGE
IG+ PBEW
Front Passenger Seat Belt Warning Light*1
Hazard Warning Signal Switch Assembly

*1: Hatchback
(Front Passenger Seat Belt Warning Light)*2
*2: Sedan
B143896E02
INSPECTION PROCEDURE
1 CHECK SUPPLEMENTAL RESTRAINT SYSTEM
DLC3.

DTC INFO
Result
Result Proceed to
No DTCs are output A
DTCs are output B
B GO TO SUPPLEMENTAL RESTRAINT SB
SYSTEM
2 CHECK OCCUPANT CLASSIFICATION SYSTEM
DLC3.
(c) Enter the following menus: DIAGNOSIS / OCCUPANT
DETECT / DTC INFO
Result
Result Proceed to
No DTCs are output A
DTCs are output B
B GO TO OCCUPANT CLASSIFICATION
SYSTEM
3 READ VALUE OF INTELLIGENT TESTER (P BUCKLE SW)
DLC3.
DATA LIST
Center Airbag Sensor Assembly
Measurement Item / Display
(Range)
Buckle switch (Front
passenger side)/
UNSET: Front passenger side
seat belt is unfastened
SET: Front passenger side seat
belt is fastened
NG: Front passenger side seat
belt is malfunctioning
OK:
Front seat inner belt assembly RH operates
normally.
OK Go to step 7
NG
4 CHECK FRONT SEAT INNER BELT ASSEMBLY RH
(a) Disconnect the J11 front seat inner belt assembly RH

Component Side:
connector.
(b) Measure the resistance.
SB Front Seat Inner Belt Assembly RH Standard resistance
Tester Connection Condition Specified Condition
1 (RBE-) - 2 (RBE+) Tongue plate fastened 10 k or higher
Tongue plate
1 (RBE-) - 2 (RBE+) Below 1
unfastened
RBE+ RBE-
(c) Reconnect the front seat inner belt assembly RH
connector.
NG REPLACE FRONT SEAT INNER BELT
ASSEMBLY RH
B118133E01
OK
5 CHECK HARNESS AND CONNECTOR (ECU - FRONT SEAT INNER BELT ASSEMBLY RH)
(a) Disconnect the J24 occupant classification ECU

Wire Harness Side: connector.
Front Seat Inner Belt Assembly RH (b) Disconnect the J11 front seat inner belt assembly RH
Connector connector.
(c) Measure the resistance.
Standard resistance
RBE- RBE+ Tester Connection Specified Condition
J24-9 (BSW) - J11-2 (RBE+) Below 1
J24-9 (BSW) or J11-2 (RBE+) - Body
J11 10 k or higher
ground
J24-5 (BGND) - J11-1 (RBE-) Below 1
Front View J24-5 (BGND) or J11-1 (RBE-) - Body

10 k or higher
ground
(d) Reconnect the occupant classification ECU connector.

Occupant Classification ECU Connector (e) Reconnect the front seat inner belt assembly connector.
NG REPAIR OR REPLACE HARNESS OR
CONNECTOR
BSW BGND
J24
Front View
B148427E01
OK
6 CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY -

OCCUPANT CLASSIFICATION ECU)
(a) Disconnect the J9 center airbag sensor assembly

Wire Harness Side: connector.
Center Airbag Sensor Assembly Connector (b) Disconnect the J24 occupant classification ECU SB
connector.
(c) Measure the resistance.
J9 Standard resistance
5 4 3 2 1 Tester Connection Specified Condition
FSP- FSP+
10 9 8 7 6
J9-12 (FSP+) - J24-8 (FSR+) Below 1
15 14 13 12 11
J9-12 (FSP+) or J24-8 (FSR+) - Body
10 k or higher
ground
J9-13 (FSP-) - J24-4 (FSR-) Below 1
J9-13 (FSP-) or J24-4 (FSR-) - Body
Occupant Classification ECU Connector 10 k or higher
ground
(d) Reconnect the center airbag sensor assembly

FSR- connector.
FSR+
(e) Reconnect the occupant classification ECU connector.
J24
CONNECTOR
Front View
B148428E01
OK
REPLACE OCCUPANT CLASSIFICATION ECU
7 PERFORM ACTIVE TEST BY INTELLIGENT TESTER (P-BELT REMIND)
DLC3.
(c) Enter the following menus: DIAGNOSIS / METER /
ACTIVE TEST
Front passenger seat belt warning light /
P-BELT REMIND -
OFF or ON
OK:
Front passenger seat belt warning light comes on.
NG REPLACE COMBINATION METER
ASSEMBLY
OK
8 INSPECT FUSE (GAUGE)
(a) Remove the GAUGE fuse from the main body ECU.
(b) Measure the resistance.
Standard resistance:
Below 1
SB (c) Reinstall the GAUGE fuse.
NG REPLACE FUSE
OK
9 INSPECT FRONT PASSENGER SEAT BELT WARNING LIGHT
(a) Hatchback:
Component Side:
(1) Remove the front passenger seat belt warning light.
Front Passenger Seat Belt Warning Light (2) Apply battery voltage to the terminals and check
that the indicator illuminates.
Standard
Tester Connection Specified Condition
Positive battery - Terminal 6 (IG+)
Illuminates
(3) Reinstall the front passenger seat belt warning light.
Battery
B128414E02
(b) Sedan:
Component Side:
(1) Remove the hazard warning signal switch
Hazard Warning Signal Switch Assembly assembly.
(Front Passenger Seat Belt Warning Light) (2) Apply battery voltage to the terminals and check
that the indicator illuminates.
Standard
Positive battery - Terminal 6 (IG+)
Illuminates
(3) Reinstall the hazard warning signal switch

assembly.
NG REPLACE FRONT PASSENGER SEAT BELT
Battery
WARNING LIGHT
B143890E01
OK
10 CHECK HARNESS AND CONNECTOR (FUSE - FRONT PASSENGER SEAT BELT

WARNING LIGHT)
(a) Hatchback:
Wire Harness Side: (1) Disconnect the D27 front passenger seat belt
Main Body ECU Connector warning light connector.
(2) Disconnect the 4S main body ECU connector.
(3) Measure the resistance.
SB
4S
Standard resistance
4S-15 - D27-6 (IG+) Below 1
4S-15 or D27-6 (IG+) - Body ground 10 k or higher
Front View
(4) Reconnect the front passenger seat belt warning
Front Passenger Seat Belt Warning light connector.
Light Connector (5) Reconnect the main body ECU connector.
IG+
D27
Front View
B143886E01
(b) Sedan:
Wire Harness Side:
(1) Disconnect the D77 hazard warning signal switch
Main Body ECU Connector assembly connector.
(2) Disconnect the 4S main body ECU connector.
4S
Standard resistance
4S-15 - D77-6 (IG+) Below 1
4S-15 or D77-6 (IG+) - Body ground 10 k or higher
Front View
(4) Reconnect the hazard warning signal switch
Hazard Warning Signal Switch Assembly
assembly connector.
Connector (Front Passenger Seat Belt
Warning Light) (5) Reconnect the main body ECU connector.
CONNECTOR
IG+ D77
Front View
B143887E01
OK
11 CHECK HARNESS AND CONNECTOR (SEAT BELT WARNING LIGHT - COMBINATION

METER ASSEMBLY)
(a) Hatchback:
Wire Harness Side: (1) Disconnect the D2 combination meter assembly
Front Passenger Seat Belt Warning connector.
Light Connector (2) Disconnect the D27 front passenger seat belt
SB warning light connector.
PBEW
Standard resistance
D27
D2-9 - D27-3 (PBEW) Below 1
Front View D2-9 or D27-3 (PBEW) - Body ground 10 k or higher
Combination Meter Assembly Connector (4) Reconnect the combination meter assembly
connector.
D2 (5) Reconnect the front passenger seat belt warning
light connector.
Front View
B147604E01
(b) Sedan:
Wire Harness Side: (1) Disconnect the D76 combination meter assembly
Hazard Warning Signal Switch Assembly connector.
Connector (Front Passenger Seat Belt (2) Disconnect the D77 hazard warning signal switch
Warning Light) assembly connector.
Standard resistance
PBEW Tester Connection Specified Condition
D77
D76-9 - D77-8 (PBEW) Below 1
Front View D76-9 or D77-8 (PBEW) - Body

10 k or higher
ground
Combination Meter Assembly Connector
(4) Reconnect the combination meter assembly
connector.
D76 (5) Reconnect the hazard warning signal switch
assembly connector.
CONNECTOR
Front View
B147605E01
OK
REPLACE MAIN BODY ECU

SB32 SEAT BELT FRONT SEAT INNER BELT ASSEMBLY (for Sedan)
FRONT SEAT INNER BELT ASSEMBLY (for Sedan)

SEAT BELT
RESTRAINTS
COMPONENTS
FRONT SEAT INNER

FRONT SEAT HEADREST
BELT ASSEMBLY
ASSEMBLY
SB
42 (430, 31)
37 (375, 27)
FRONT SEAT
x4
ASSEMBLY
BUCKLE SWITCH
CONNECTOR
w/ Front Seat Side Airbag:
BUCKLE SWITCH
CONNECTOR
AIRBAG
CONNECTOR
N*m (kgf*cm, ft*lbf) : Specified torque
B138568E01
SEAT BELT FRONT SEAT INNER BELT ASSEMBLY (for Sedan) SB33
REMOVAL
CAUTION:
Some of these service operations affect the SRS airbag
system. Read the precautionary notices concerning the
SRS airbag system before servicing (w/ Front Seat Side
Airbag) (See page RS-1).
NOTICE:
Always use "Torx" socket wrench E10 when removing
the front seat.
SB
HINT:
The procedure described below is for the driver side. Use the
same procedure for both the front passenger and driver
sides, unless otherwise specified.
TERMINAL
CAUTION:
Wait for at least 90 seconds after disconnecting the
cable to prevent the airbag from working (w/ Front
Seat Side Airbag).
2. REMOVE FRONT SEAT HEADREST ASSEMBLY (See
page SE-5)
3. REMOVE FRONT SEAT ASSEMBLY (See page SE-5)
4. REMOVE FRONT SEAT INNER BELT ASSEMBLY
(a) for Driver Side:
(1) Disconnect the seat position sensor connector.
(2) Using a clip remover, remove the connector.
(3) Using a clip remover, remove the clamp.
(4) Remove the clamp.
B138569
(b) for Front Passenger Seat:

(1) Using a clip remover, remove the connector.
SB
B138570
(c) Remove the wire harness from the claw of the front
seat cushion inner shield.
(d) Remove the nut and the front seat inner belt.
B138351
INSPECTION
1. INSPECT FRONT SEAT INNER BELT ASSEMBLY
(1) Check the resistance.
1. Using an ohmmeter, measure the resistance
between the terminals.
Release Standard resistance
Tongue plate fastened 10 k or higher
3-4
Tongue plate released Below 1
Fasten
front seat inner belt.
Ohmmeter
B114760E01
(b) for Front Passenger Side:

Standard resistance
Release 1-2
SB
Fasten
front seat inner belt.
Ohmmeter
B114761E01
INSTALLATION
CAUTION:
system. Read the precautionary concerning the SRS
airbag system before servicing (w/ Front Seat Side
NOTICE:
SB Always use "Torx" socket wrench E10 when installing the
front seat.
HINT:
same procedure for both the front passenger and drive sides,
unless otherwise specified.
1. INSTALL FRONT SEAT INNER BELT ASSEMBLY
(a) Install the front seat inner belt with the nut.
Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf)
NOTICE:
Do not place the front seat inner belt over the
convex areas of the front seat adjuster frame.
(b) Install the wire harness into the claw of the front
Convex seat cushion inner shield.
B138352E01
(c) for Driver Side:

(1) Install the 2 clamps.
(2) Install the connector.
(3) Connect the seat position sensor connector.
B138569
(d) for Front Passenger Side:

(1) Install the 2 clamps.
(2) Install the connector.
2. INSTALL FRONT SEAT ASSEMBLY (See page SE-20)
3. INSTALL FRONT SEAT HEADREST ASSEMBLY (See
page SE-21)
TERMINAL
SB
5. INSPECT SRS WARNING LIGHT (w/ Front Seat Side
Airbag)
(See page RS-31)
B138570
SEAT BELT FRONT SEAT INNER BELT ASSEMBLY (for Hatchback) SB37
FRONT SEAT INNER BELT ASSEMBLY (for Hatchback)

SEAT BELT
RESTRAINTS
COMPONENTS
for Driver Side:
FRONT SEAT SB
HEADREST
ASSEMBLY
42 (430, 31)
FRONT SEAT INNER

BELT ASSEMBLY
FRONT SEAT
ASSEMBLY
37 (375, 27)
x4
BUCKLE SWITCH
CONNECTOR
BUCKLE SWITCH
CONNECTOR
AIRBAG
CONNECTOR
B114721E01
SB38 SEAT BELT FRONT SEAT INNER BELT ASSEMBLY (for Hatchback)
for Front Passenger Side:
FRONT SEAT
HEADREST
ASSEMBLY
SB
FRONT SEAT
ASSEMBLY
37 (375, 27)
x4
OCCUPANT DETECTION
SENSOR CONNECTOR
BUCKLE SWITCH
CONNECTOR
FRONT SEAT INNER
BELT ASSEMBLY 42 (430, 31)
BUCKLE SWITCH
CONNECTOR
AIRBAG
CONNECTOR
OCCUPANT DETECTION
SENSOR CONNECTOR
B114722E01
REMOVAL
CAUTION:
Airbag) (See pageRS-1).
NOTICE:
the front seat.
SB
HINT:
same procedure for both the driver and front passenger
TERMINAL
CAUTION:
Seat Side Airbag).
2. REMOVE FRONT SEAT HEADREST ASSEMBLY (See
page SE-28)
3. REMOVE FRONT SEAT ASSEMBLY (See page SE-28)
(1) Disconnect the seat position sensor connector.
(2) Remove the buckle switch connector.
(3) Remove the 2 wiring harness clamps.
B114765
(4) Remove the wire harness from the claw of the

front seat cushion shield.
(5) Remove the bolt and the front seat inner belt.
B114766

(1) Remove the buckle switch connector.
(2) Remove the 2 wiring harness clamps.
SB
B114764
(3) Remove the wiring harness from the claw of the

(4) Remove the bolt and the front seat inner belt.
B114762
INSPECTION
1. INSPECT FRONT SEAT INNER BELT ASSEMBLY
Release Standard resistance
3-4
Fasten
seat inner belt.
Ohmmeter
B114760E01

Standard resistance
Release 1-2
SB
Fasten
seat inner belt.
Ohmmeter
B114761E01
INSTALLATION
CAUTION:
Airbag) (See pageRS-1).
NOTICE:
SB Always use "Torx" socket wrench E10 when installing the
front seat.
HINT:
1. INSTALL FRONT SEAT INNER BELT ASSEMBLY
(1) Install the front seat inner belt with the bolt.
NOTICE:
Do not place the front seat inner belt over
the convex areas of the front seat adjuster
frame.
Convex (2) Install the wire harness into the claw of the front
B114767E01 seat cushion shield.
(3) Install the 2 wiring harness clamps.

(4) Install the buckle switch connector.
(5) Connect the seat position sensor connector.
B114765

(1) Install the front seat inner belt with the bolt.
NOTICE:
Do not place the front seat inner belt over
the convex areas of the front seat adjuster
Convex frame.
(2) Install the wiring harness onto the claw of the
B114763E01
(3) Install the 2 wiring harness clamps.

(4) Install the buckle switch connector.
2. INSTALL FRONT SEAT ASSEMBLY (See page SE-42)
3. INSTALL FRONT SEAT HEADREST ASSEMBLY (See
page SE-43)
TERMINAL
SB
B114764

Airbag)
(See page RS-31)
SEAT BELT FRONT SEAT OUTER BELT ASSEMBLY (for Sedan) SB43
FRONT SEAT OUTER BELT ASSEMBLY (for Sedan)

SEAT BELT
RESTRAINTS
COMPONENTS
FRONT SHOULDER BELT

ANCHOR ADJUSTER ASSEMBLY
SB
42 (430, 31)
x2 CENTER PILLAR
UPPER GARNISH
SHOULDER BELT ANCHORAGE

PLATE COVER REAR DOOR OPENING
TRIM WEATHERSTRIP
FRONT DOOR OPENING 42 (430, 31)

TRIM WEATHERSTRIP
4.9 (50, 43 in.*lbf)
SEAT BELT ANCHOR

COVER CAP
42 (430, 31) REAR DOOR

CENTER PILLAR SCUFF PLATE
LOWER GARNISH
FRONT SEAT OUTER

BELT ASSEMBLY
PRETENSIONER
FRONT DOOR CONNECTOR
SCUFF PLATE
LAP BELT OUTER

ANCHOR COVER
42 (430, 31)
N*m (kgf*cm, ft.*lbf) : Specified torque
B134890E01
SB44 SEAT BELT FRONT SEAT OUTER BELT ASSEMBLY (for Sedan)
REMOVAL
CAUTION:
SRS airbag system before servicing (See page RS-1).
HINT:
The procedure described below is for the RH side. Use the
SB same procedure for both the RH and LH sides, unless
otherwise specified.
TERMINAL
CAUTION:
cable to prevent the airbag from working.
2. REMOVE FRONT DOOR SCUFF PLATE (See page IR-
14)
3. REMOVE REAR DOOR SCUFF PLATE (See page IR-
15)
4. REMOVE FRONT DOOR OPENING TRIM
WEATHERSTRIP
(a) Remove the front door opening trim weatherstrip to
the extent that the center pillar upper and lower
garnishes can be removed.
B138445
5. REMOVE REAR DOOR OPENING TRIM

WEATHERSTRIP
(a) Remove the rear door opening trim weatherstrip to
6. REMOVE CENTER PILLAR LOWER GARNISH (See
page IR-16)
B138446
7. REMOVE SEAT BELT ANCHOR COVER CAP

(a) Pull portion A, shown in the illustration, toward you,
remove the 2 claws on the lower side followed by
the claw on the upper side. Then remove the seat
belt anchor cover cap.
A
B114421E01
8. REMOVE LAP BELT OUTER ANCHOR COVER

(a) Disengage the 3 claws and remove the lap belt
outer anchor cover.
SB
B134891
9. REMOVE FRONT SEAT OUTER BELT ASSEMBLY

(a) Remove the bolt and the anchor plate.
B134892
(b) Remove the bolt and the shoulder anchor.
B114296
(c) Disconnect the pretensioner connector.

(1) Using a screwdriver, release the locking button.
(2) Using a screwdriver, disconnect the
pretensioner connector.
Locking Button
B134893E01
(d) Remove the 2 bolts, the 2 hooks and the retractor.

10. REMOVE CENTER PILLAR UPPER GARNISH (See
page IR-17)
SB
B134896
11. REMOVE SHOULDER BELT ANCHORAGE PLATE

COVER
(a) Disengage the 2 claws and remove the shoulder
belt anchorage plate cover.
B134897
12. REMOVE FRONT SHOULDER BELT ANCHOR

ADJUSTER ASSEMBLY
(a) Remove the 2 bolts, the hook and the front shoulder
belt anchor adjuster.
B134898
INSTALLATION
CAUTION:
HINT:
same procedure for both the RH and LH sides, unless
SB
1. INSTALL FRONT SHOULDER BELT ANCHOR
ADJUSTER ASSEMBLY
(a) Insert the hook into the body hole and install the
shoulder belt anchor adjuster with the 2 bolts.
B134898
2. INSTALL SHOULDER BELT ANCHORAGE PLATE

COVER
(a) Engage the 2 claws and install the shoulder belt
anchorage plate cover.
3. INSTALL CENTER PILLAR UPPER GARNISH (See
page IR-31)
B134897
4. INSTALL FRONT SEAT OUTER BELT ASSEMBLY

Unlock
(a) Check the angle of inclination required to lock the
45 retractor.
(1) Gently incline the retractor from its initial
Lock position. Check that the belt does not lock
when the retractor is inclined 15 or less in any
direction. Also, check that the belt locks when
the inclination of the retractor is 45 or more.
NOTICE:
B114426E01 Do not disassemble the retractor.
If the operation is not as specified, replace the
front seat outer belt.
(b) Hook the lower stay of the retractor onto the 2 body
hooks and provisionally install the retractor with the
A 2 bolts.
(c) Tighten bolt A and then bolt B.
Torque: 4.9 N*m (50 kgf*cm, 43 in.*lbf) for bolt A
42 N*m (430 kgf*cm, 31 ft.*lbf) for bolt B
B
B134896E01
(d) Connect the pretensioner connector.

(1) Connect the pretensioner connector.
(2) Lock the locking button.
NOTICE:
Securely lock the locking button.
SB
Lock Button
B134894E01
(e) Install the shoulder anchor with the bolt.

B114296
(f) Install the anchor plate with the bolt.

(g) Check that the ELR locks.
NOTICE:
The check should be performed with the front
seat outer belt installed.
Do not allow the anchor part of the front seat
outer belt and the protruding parts of the floor
panel to overlap.
B134892 (1) With the belt installed, check that the belt locks
when it is pulled out quickly.
5. INSTALL LAP BELT OUTER ANCHOR COVER

(a) Engage the 3 claws and install the lap belt outer
anchor cover.
SB
B134891
6. INSTALL SEAT BELT ANCHOR COVER CAP

(a) Engage the 3 claws and install the seat belt anchor
cover cap.
7. INSTALL CENTER PILLAR LOWER GARNISH (See
page IR-32)
B114428
8. INSTALL REAR DOOR OPENING TRIM

WEATHERSTRIP
(a) Install the rear door opening trim weatherstrip.
B138446
9. INSTALL FRONT DOOR OPENING TRIM

WEATHERSTRIP
(a) Install the front door opening trim weatherstrip.
10. INSTALL REAR DOOR SCUFF PLATE (See page IR-
34)
11. INSTALL FRONT DOOR SCUFF PLATE (See page IR-
35)
B138445
TERMINAL
13. INSPECT SRS WARNING LIGHT
(See page RS-31)
DISPOSAL
CAUTION:
Never dispose of a front seat outer belt that has an
inactivated pretensioner.
The seat belt pretensioner produces a loud, exploding
sound when it activates. Perform the operation
outside and where it will not be a nuisance to persons
SB nearby.
When activating a front seat outer belt (with seat belt
pretensioner), stand at least 10 m (33 ft) away from the
Use gloves and safety glasses when handling a front
seat outer belt with an activated pretensioner.
Always wash your hands with water after completing
the activation.
Do not apply water to a front seat outer belt that has
an activated pretensioner.
When activating the seat belt pretensioner, always use
the specified SST (SRS airbag deployment tool).
Perform the operation in a place away from electrical
interference.
HINT:
1. DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY
(When Installed in Vehicle)
HINT:
Prepare a battery as the power source to activate the
seat belt pretensioner.
(a) Check whether SST is functioning.
SST 09082-00700
CAUTION:
Always use the specified SST when activating
SST
the seat belt pretensioner.
B104819E01
(1) Connect the SST red clip to the positive battery

terminal and the black clip to the negative
battery terminal.
Battery HINT:
Do not connect the yellow connector. The
yellow connector is for connections to the seat
belt pretensioner.
SST
B104820E01
(2) Press the SST activation switch and check that

the LED of the SST activation switch turns on.
CAUTION:
If the LED illuminates when the activation
switch is not being pressed, SST may be
malfunctioning. Do not use SST.
(b) Disconnect SST from the battery.
SST (1) Disconnect the cable from the negative battery SB
B104821E01 terminal.
(2) Remove the front door scuff plate (See page
IR-14).
(3) Remove the rear door scuff plate (See page IR-
15).
(4) Remove the front door opening trim
weatherstrip.
1. Remove the front door opening trim
weatherstrip to the extent that the center
pillar lower garnish can be removed.
B138447
(5) Remove the rear door opening trim

weatherstrip.
1. Remove the rear door opening trim
(6) Remove the center pillar lower garnish (See
page IR-16).
B138448
(7) Disconnect the pretensioner connector.

1. Using a screwdriver, release the locking
button.
2. Using a screwdriver, disconnect the
SB
Locking Button
B134893E01
(d) Connect SST.

(1) Connect SST, then the yellow connector to the
SST 09082-00770
NOTICE:
Do not lock the secondary lock of the twin
lock to avoid damaging the SST connector
and wire harness.
SST
Locking Button
B134895E01
(2) Move SST at least 10 m (33 ft) away from the

front of the vehicle.
SST 09082-00700
(3) Close the doors and windows of the vehicle.
NOTICE:
Take care not to damage the SST wire
harness.
HINT:
Do not close the windows fully. Leave a gap for SB
inserting the SST wire harness.
battery terminal.
(e) Activate the seat belt pretensioner.
Battery (1) Confirm that no one is inside the vehicle or
10 m (33 ft) within 10 m (33 ft) of the vehicle.
(2) Press the SST activation switch and activate
SST HINT:
The seat belt pretensioner operates
B134899E01 simultaneously with the SST activation switch
LED light.
(f) Disconnect SST.
(g) Dispose of the front seat outer belt (with the seat
belt pretensioner).
HINT:
When scrapping a vehicle, activate the seat belt
pretensioner, and then scrap the vehicle with the
activated front seat outer belt still installed.
CAUTION:
Do not touch the front seat outer belt for at
least 30 minutes after the seat belt
pretensioner has been activated. It is very
hot.
Use gloves and safety glasses when handling
a front seat outer belt with a pretensioner that
has been activated.
Always wash your hands with water after
completing the operation.
Do not apply water to a front seat outer belt
that has an activated pretensioner.
(When not Installed in Vehicle)
HINT:
NOTICE:
When only disposing of the front seat outer belt
(with the seat belt pretensioner), never use the
customer's vehicle to activate the seat belt
pretensioner.
Be sure to follow the procedures described below
when activating the seat belt pretensioner.
(a) Remove the front seat outer belt (See page SB-44).
(b) Wind the seat belt with the retractor.

Cut (c) When the seat belt is sufficiently wound, cut the
10 cm
(0.328 ft)
seat belt approximately 10 cm (0.328 ft) from the
retractor, as shown in the illustration.
HINT:
The retractor resistance increases in correlation
with how much the seat belt is wound.
SB
B114471E01
(d) Check whether SST is functioning.

SST 09082-00700
CAUTION:
SST
B104819E01

battery terminal.
Battery HINT:
belt pretensioner.
SST
B104820E01

CAUTION:
If the LED illuminates when the activation
SST
B104821E01
(e) Connect SST.

(1) Connect SST, then the yellow connector to the
SST 09082-00770
NOTICE:
and wire harness.
SB
SST
Locking Button
B114472E01
(2) Using a service-purpose wire harness for the

vehicle, tie the seat belt pretensioner to the tire
with a wheel attached.
Stripped wire harness section
Area Measurement
A
A 1.25 mm or more (0.0019 in2 or more)
2
CAUTION:
Stripped Wire Harness Section
Do not use wire harnesses that are too
B104882E01 thin or any other object to tie the seat
belt pretensioner because they may snap
due to the shock when the pretensioner
is deployed.
Always use a wire harness for vehicle
use, with a cross section of at least 1.25
mm2 (0.0019 in2).
HINT:
To calculate the area of the stripped wire
harness cross section:
Area = 3.14 x (Diameter)2 divided by 4
(3) Connect SST.

SST 09082-00700
NOTICE:
Do not lock the secondary lock of the
twin lock to avoid damaging the SST
connector and wire harness.
Set up the front seat outer belt, as shown
SST in the illustration.
SB Wire Harness
B114473E01

wheel.
NOTICE:
Take care not to damage the SST wire
harness.
(f) Activate the seat belt pretensioner.
Battery battery terminal.
(2) Check that no one is within 10 m (33 ft) of the
wheel.
HINT:
simultaneously with the SST activation switch
LED light.
10 m (33 ft)
(g) Disconnect SST.
SST
B114550E01
(h) Dispose of the front seat outer belt (with the seat
belt pretensioner).
CAUTION:
Plastic Bag hot.
an front seat outer belt with a pretensioner
B114475E01 that has been activated.
(1) Place the front seat outer belt in a plastic bag,

tie the end tightly and dispose of it in the same
way as other general parts.
SB
SB58 SEAT BELT FRONT SEAT OUTER BELT ASSEMBLY (for Hatchback 5 Door)
FRONT SEAT OUTER BELT ASSEMBLY (for Hatchback 5

SEAT BELT
RESTRAINTS
Door)
COMPONENTS
SB
FRONT SHOULDER BELT
ANCHOR ADJUSTER ASSEMBLY
42 (430, 31)
x2 CENTER PILLAR
UPPER GARNISH
REAR DOOR OPENING

TRIM WEATHERSTRIP
SHOULDER BELT
ANCHOR COVER
42 (430, 31)
FRONT DOOR OPENING
TRIM WEATHERSTRIP
4.9 (50, 43 in.*lbf)
SEAT BELT ANCHOR

COVER CAP
REAR DOOR
42 (430, 31)
SCUFF PLATE
FRONT SEAT OUTER

BELT ASSEMBLY
PRETENSIONER
FRONT DOOR CONNECTOR
SCUFF PLATE CENTER PILLAR
LOWER GARNISH 42 (430, 31)
B114418E01
SEAT BELT FRONT SEAT OUTER BELT ASSEMBLY (for Hatchback 5 Door) SB59
REMOVAL
CAUTION:
HINT:
SB
TERMINAL
CAUTION:
49)
51)
WEATHERSTRIP
B114419

WEATHERSTRIP
6. REMOVE CENTER PILLAR LOWER GARNISH (See
page IR-55)
B114420

(a) Pull portion A, shown in the illustration, toward you,
remove the 2 claws on the lower side followed by
the claw on the upper side. Then remove the seat
belt anchor cover cap.
A
B114421E01

(a) Remove the anchor plate cover.
SB
B114294
(b) Remove the bolt and the anchor plate.
B114295
(c) Remove the bolt and the through anchor.
B114296
(d) Disconnect the pretensioner connector.

Locking Button
B114422E01
(e) Remove the 2 bolts, the 2 hooks and the retractor.

9. REMOVE CENTER PILLAR UPPER GARNISH (See
page IR-55)
SB
B114423
10. REMOVE SHOULDER BELT ANCHOR COVER

(a) Disengage the 2 claws and remove the shoulder
belt anchor cover.
B114424
11. REMOVE FRONT SHOULDER BELT ANCHOR

ADJUSTER ASSEMBLY
(a) Remove the 2 bolts, the hook and the front shoulder
belt anchor adjuster.
B114425
INSTALLATION
CAUTION:
HINT:
SB same procedure for both the RH and LH sides, unless
1. INSTALL FRONT SHOULDER BELT ANCHOR
ADJUSTER ASSEMBLY
shoulder belt anchor adjuster with the 2 bolts.
B114425
2. INSTALL SHOULDER BELT ANCHOR COVER

(a) Engage the 2 claws and install the shoulder belt
anchor cover.
3. INSTALL CENTER PILLAR UPPER GARNISH (See
page IR-76)
B114424

Unlock
45 retractor.
NOTICE:
A
2 bolts.
B
B114423E01
(d) Install the through anchor with the bolt.

(e) Check that the ELR locks.
NOTICE:
Perform the check with the front seat outer belt
installed.
(1) With the belt installed, check that the belt locks
If the operation is not as specified, replace the SB
B114296 front seat outer belt.
(f) Connect the pretensioner connector.

NOTICE:
Locking Button
B114427E01
(g) Install the anchor plate with the bolt.

B114295
(h) Install the anchor plate cover.
B114294

cover cap.
6. INSTALL CENTER PILLAR LOWER GARNISH (See
page IR-76)
SB
B114428

WEATHERSTRIP
B114420

WEATHERSTRIP
80)
82)
B114419
TERMINAL
(See page RS-31)
DISPOSAL
CAUTION:
nearby.
Stand at least 10 m (33 ft) away when activating a front
SB
seat outer belt (with seat belt pretensioner).
an activation.
Always use the specified SST (SRS airbag deployment
tool) when activating the seat belt pretensioner.
interference.
HINT:
same procedure for the RH and LH sides, unless otherwise
specified.
HINT:
SST 09082-00700
CAUTION:
SST
B104819E01

battery terminal.
Battery HINT:
belt pretensioner.
SST
B104820E01

CAUTION:
If the LED turns on when the activation
SB SST (1) Disconnect the cable from negative battery
IR-49).
(3) Remove the rear door scuff plate (See page IR-
51).
weatherstrip.
1. Remove the front door opening trim
B119867
(5) Remove the rear door opening trim

weatherstrip.
1. Remove the rear door opening trim
(6) Remove the center pillar lower garnish (See
page IR-55 ).
B119869
(7) Disconnect the pretensioner connector as

shown in the illustration.
SB
Locking Button
B114422E01
(d) Connect SST.

(1) Connect SST, then connect the yellow
connector to the seat belt pretensioner.
SST 09082-00770
NOTICE:
and wire harness
SST
Locking Button
B114456E01

front of the vehicle.
SST 09082-00700
HINT:
Do not close the windows fully. Leave a gap for
NOTICE:
SB Do not damaging the SST wire harness.
battery terminal.
(1) Confirm that no one is inside the vehicle or
within 10 m (33 ft) of the vehicle.
Battery (2) Press the SST activation switch and activate
10 m (33 ft) the seat belt pretensioner.
HINT:
SST simultaneously with the SST activation switch
B114470E01 LED light.
(f) Disconnect SST.
belt pretensioner).
HINT:
CAUTION:
hot.
has been activated.
HINT:
NOTICE:
pretensioner.
Follow the procedure described below when
activating the seat belt pretensioner.
(a) Remove the front seat outer belt assembly (See
page SB-59).

10 cm
(0.328 ft)
HINT:
SB
B114471E01

SST 09082-00700
CAUTION:
SST
B104819E01

battery terminal.
Battery HINT:
belt pretensioner.
SST
B104820E01

CAUTION:
SST
B104821E01
(e) Connect SST.

SST 09082-00770
NOTICE:
and wire harness.
SB
SST
Locking Button
B114472E01

Stripped wire harness section:
Area Measurement
A
A 1.25 mm2 or more (0.0019 in2 or more)
CAUTION:
Stripped Wire Harness Section Do not use wire harnesses that are too
B104882E01 thin or any other object to tie the seat
is deployed.
mm2 (0.0019 in2).
HINT:
(3) Connect SST.

SST 09082-00700
NOTICE:
Set up the front seat outer belt, as shown
Wire Harness SB
B114473E01

wheel.
NOTICE:
Do not damage the SST wire harness.
battery terminal.
Battery (2) Check that no one is within 10 m (33 ft) of the
wheel.
HINT:
LED light.
(g) Disconnect SST.
10 m (33 ft)
SST
B114550E01
belt pretensioner).
CAUTION:
Plastic Bag hot.
B114475E01 has been activated.

SB
FRONT SEAT OUTER BELT ASSEMBLY (for Hatchback 3

SEAT BELT
RESTRAINTS
Door)
COMPONENTS
SB
PACKAGE TRAY TRIM

PANEL ASSEMBLY
DECK BOARD
SUB-ASSEMBLY
DECK FLOOR BOX
DECK FLOOR BOX
B127707E02
for 60/40 Split Seat Type:
REAR SEAT
ASSEMBLY
NO. 1 REAR SEAT
LEG COVER SB
37 (375, 27)
REAR SEAT
x6 ASSEMBLY
NO. 2 REAR SEAT

LEG COVER
NO. 1 REAR SEAT 37 (375, 27)

LEG COVER x7
for Hold Down Seat Type:
REAR SEATBACK
ASSEMBLY
REAR SEAT CUSHION COVER
PAD SUB-ASSEMBLY
37 (375, 27)
x4
B121713E05
SB
42 (430, 31)
SEAT BELT ANCHOR

COVER CAP
4.9 (50, 43 in.*lbf)
REAR SEAT OUTER

BELT ASSEMBLY
PRETENSIONER
CONNECTOR FRONT QUARTER TRIM
PANEL ASSEMBLY
42 (430, 31)
FRONT SEAT OUTER
BELT ASSEMBLY
42 (430, 31)
FRONT DOOR OPENING
FRONT DOOR TRIM WEATHERSTRIP
SCUFF PLATE

B138697E01
REMOVAL
CAUTION:
NOTICE:
the rear seat.
HINT:
SB
TERMINAL
CAUTION:
2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
(See page IR-48)
3. REMOVE DECK BOARD SUB-ASSEMBLY (See page
IR-48)
4. REMOVE DECK FLOOR BOX
(a) for RH Side:
(1) Remove the deck floor box (See page IR-48).
(b) for LH Side:
HINT:
Use the same procedure as for the RH side.
5. REMOVE NO. 1 REAR SEAT LEG COVER (for 60/40
Split Seat Type)
(a) for RH Side:
(1) Remove the No. 1 rear seat leg cover (See
page SE-89).
(b) for LH Side:
page SE-70).
Split Seat Type LH Side) (See page SE-70)
7. REMOVE REAR SEAT ASSEMBLY (for 60/40 Split
Seat Type)
(a) for RH Side:
(1) Remove the rear seat assembly (See page SE-
89).
(b) for LH Side:
71).
8. REMOVE REAR SEAT CUSHION COVER PAD SUB-
ASSEMBLY (for Hold Down Seat Type) (See page SE-
114)
9. REMOVE REAR SEATBACK ASSEMBLY (for Hold
Down Seat Type) (See page SE-115)

97)
WEATHERSTRIP
the extent that the front quarter trim panel can be
removed.
SB
B114477
12. REMOVE REAR SEAT OUTER BELT ASSEMBLY

(a) Remove the belt.
B114498
13. REMOVE FRONT QUARTER TRIM PANEL

ASSEMBLY
(a) Disengage the 8 clips, the retainer and the 10 claws
and remove the front quarter trim panel.
B114499

(a) Disengage the 3 claws and remove the seat belt
anchor cover cap.
B114478

(a) Remove the anchor plate cover.
SB
B114496
(b) Remove the bolt and the anchor plate.
B114497
B114479
(d) Disconnect the pretensioner connector.

Locking Button
B114422E01
(e) Remove the 2 bolts, the 2 hooks and the retractor.
SB
B114423
INSTALLATION
CAUTION:
NOTICE:
Always use "Torx" socket wrench E10 when installing the
rear seat.
HINT:
SB
Unlock
45 retractor.
NOTICE:
A
2 bolts.
B
B114423E01
(d) Install the through anchor with the bolt.

NOTICE:
Perform the check with the front seat outer belt
installed
B114479 front seat outer belt.
(f) Install the anchor plate with the bolt.

SB
B114497
(g) Install the anchor plate cover.
B114496
(h) Connect the pretensioner connector.

NOTICE:
Locking Button
B114427E01

cover cap.
B114478
3. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY

(a) Engage the 8 clips, the retainer and the 10 claws
and install the front quarter trim panel.
SB
B114499
4. INSTALL REAR SEAT OUTER BELT ASSEMBLY

(a) Install the belt.
B114498

WEATHERSTRIP
119)
7. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split
Seat Type)
(a) for RH Side:
B114477 (1) Install the rear seat assembly (See page SE-
102).
(b) for LH Side:
(1) Install the rear seat assembly (See page SE-
84).
8. INSTALL NO. 2 REAR SEAT LEG COVER (for 60/40
Split Seat Type)
(a) for RH Side:
(1) Install the No. 1 rear seat leg cover (See page
SE-89).
(b) for LH Side:
SE-85).
10. INSTALL REAR SEATBACK ASSEMBLY (for Hold
11. INSTALL REAR SEAT CUSHION COVER PAD SUB-

123)
12. INSTALL DECK FLOOR BOX
(a) for RH side:
(1) Install the deck floor box (See page IR-83).
(b) for LH Side:
SB HINT:
13. INSTALL DECK BOARD SUB-ASSEMBLY (See page
IR-83)
14. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
(See page IR-83)
TERMINAL
(See page RS-31)
DISPOSAL
CAUTION:
nearby.
Stand at least 10 m (33 ft) away when activating a front
SB
seat outer belt (with seat belt pretensioner).
an activation.
Always use the specified SST (SRS airbag deployment
tool) when activating the seat belt pretensioner.
interference.
NOTICE:
the rear seat.
HINT:
HINT:
SST 09082-00700
CAUTION:
SST
B104819E01

battery terminal.
Battery HINT:
belt pretensioner.
SST
B104820E01

CAUTION:
SB SST (1) Disconnect the cable from the negative battery
(2) Remove the package tray trim panel assembly
(See page IR-48).
(3) Remove the deck board sub-assembly (See
page IR-48).
(4) Remove the deck floor box RH (See page IR-
48).
(5) Remove the deck floor box LH (for 60/40 Split
Seat Type and Bench Seat Type).
HINT:
(6) Remove the rear seat No. 1 leg cover (for 60/
40 Split Seat Type) (See page SB-75).
(7) Remove the rear seat No. 2 leg cover (for 60/
40 Split Seat Type LH Side) (See page SE-70).
(8) Remove the rear seat assembly (for 60/40 Split
Seat Type) (See page SB-75).
(9) Remove the rear seat cushion cover pad sub-
assembly (for Bench Seat Type) (See page SE-
114).
(10) Remove the rear seatback assembly (for
Bench Seat Type) (See pageSE-115).
IR-97).
weatherstrip (See page SB-76).
(13) Remove the rear seat outer belt assembly.
1. Remove the belt.
B114498
(14) Remove the front quarter trim panel assembly.

1. Disengage the 8 clips, the retainer and the
10 claws and remove the front quarter trim
panel.
SB
B114499
(15) Disconnect the pretensioner connector as

Locking Button
B114422E01
(d) Connect SST.

SST 09082-00770
NOTICE:
and wire harness.
SB
SST
Locking Button
B114456E01
(2) Move the SST at least 10 m (33 ft) away from

the front of the vehicle.
SST 09082-00700
HINT:
Do not close the windows fully. Leave a gap for
NOTICE:
battery terminal.
(1) Confirm that no one is inside the vehicle or
within 10 m (33 ft) of the vehicle.
Battery (2) Press the SST activation switch and activate
10 m (33 ft) the seat belt pretensioner.
HINT:
SST simultaneously with the SST activation switch
B114480E01 LED light.
(f) Disconnect SST.
belt pretensioner).
HINT:
CAUTION:
hot.
an front seat outer belt with a pretensioner
that has been activated.
Always wash your hands with water after SB
HINT:
NOTICE:
pretensioner.
Follow the procedure described below when
activating the seat belt pretensioner.
(a) Remove the front seat outer belt assembly (See
page SB-75).
10 cm
(0.328 ft)
HINT:
B114471E01

SST 09082-00700
CAUTION:
SST
B104819E01

battery terminal.
Battery HINT:
belt pretensioner.
SB SST
B104820E01

CAUTION:
SST
B104821E01
(e) Connect SST.

SST 09082-00770
NOTICE:
and wire harness.
SST
Locking Button
B114472E01

Stripped wire harness section:
Area Measurement
A
A 1.25 mm or more (0.0019 in2 or more)
2
Stripped Wire Harness Section

B104882E01
CAUTION:
Do not use wire harnesses that are too
thin or any other object to tie the seat
is deployed.
mm2 (0.0019 in2). SB
HINT:
(3) Connect SST.
SST 09082-00700
NOTICE:
Set up the front seat outer belt as shown
Wire Harness
B114473E01

wheel.
NOTICE:
battery terminal.
Battery (2) Check that no one is within 10 m (33 ft) of the
wheel.
HINT:
LED light.
(g) Disconnect SST.
10 m (33 ft)
SST
B114550E01
belt pretensioner).
CAUTION:
Plastic Bag hot.
SB a front seat outer belt with a pretensioner that
B114475E01 has been activated.
SEAT BELT REAR SEAT INNER BELT ASSEMBLY (for Sedan) SB89
REAR SEAT INNER BELT ASSEMBLY (for Sedan)

SEAT BELT
RESTRAINTS
COMPONENTS
SB
REAR SEAT INNER

BELT ASSEMBLY
REAR SEAT INNER

BELT ASSEMBLY
REAR SEAT CUSHION

COVER PAD SUB-ASSEMBLY
42 (430, 31)
42 (430, 31)
B138566E01
SB90 SEAT BELT REAR SEAT INNER BELT ASSEMBLY (for Sedan)
REMOVAL
ASSEMBLY
(a) for 60/40 Split Seat Type:
(1) Remove the rear seat cushion cover pad (See
page SE-46).
(b) for Fixed Seat Type:
SB (1) Remove the rear seat cushion cover pad (See
page SE-106).
2. REMOVE REAR SEAT INNER BELT ASSEMBLY
(a) for RH Side (for 60/40 Split Seat Type):
(1) Remove the bolt and the rear seat inner belt.
B134907
(b) LH Side:
B134904
INSTALLATION
1. INSTALL REAR SEAT INNER BELT ASSEMBLY
(a) for RH Side (60/40 Split Seat Type):
(1) Install the rear seat inner belt with the bolt.
NOTICE:
Install the anchor plate with the arrow
mark facing forward.
Do not place the anchor plate over the
locating mark area of the floor panel.
Arrow Mark
Locating Mark
B134908E01
SEAT BELT REAR SEAT INNER BELT ASSEMBLY (for Sedan) SB91
(b) for LH Side:

NOTICE:
SB
ASSEMBLY
(1) Install the rear seat cushion cover pad (See
page SE-53).
Arrow Mark
Locating Mark (b) for Fixed Seat Type:
B134905E01 (1) Install the rear seat cushion cover pad (See
page SE-109).
SB92 SEAT BELT REAR SEAT INNER BELT ASSEMBLY (for Hatchback LH Side)
REAR SEAT INNER BELT ASSEMBLY (for Hatchback LH

SEAT BELT
RESTRAINTS
Side)
COMPONENTS

SB
NO. 1 REAR SEAT REAR SEAT INNER 42 (430, 31)
LEG COVER BELT ASSEMBLY
NO. 2 REAR SEAT

LEG COVER
37 (375, 27) REAR SEAT CUSHION

x3
ASSEMBLY
REAR SEAT INNER

BELT ASSEMBLY

PAD SUB-ASSEMBLY
42 (430, 31)
B117789E02
SEAT BELT REAR SEAT INNER BELT ASSEMBLY (for Hatchback LH Side) SB93
REMOVAL
NOTICE:
the rear seat.
Split Seat Type) (See page SE-71)
SB
114)
(1) Using "Torx" socket wrench E10, remove the 3
bolts and pull up the rear seat cushion.
B114740
(2) Remove the belt from the band.

Band
B114647E01
(b) for Hold Down Seat Type:

B119857
SB94 SEAT BELT REAR SEAT INNER BELT ASSEMBLY (for Hatchback LH Side)
INSTALLATION
NOTICE:
rear seat.
SB Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf)
NOTICE:
convex area of the rear seat back frame.
Convex
(2) Install the belt into the band.
Band
B114648E01
(3) Install the rear seat cushion.

(4) Using "Torx" socket wrench E10, tighten the 3
bolts in the sequence shown in the illustration.
2 1
B114740E01

NOTICE:
Arrow Mark Locating Mark 4. INSTALL REAR SEAT CUSHION COVER PAD SUB-
B119858E02 ASSEMBLY (for Hold Down Seat Type) (See page SE-
123)
SEAT BELT REAR SEAT INNER BELT ASSEMBLY (for Hatchback RH Side) SB95
REAR SEAT INNER BELT ASSEMBLY (for Hatchback RH

SEAT BELT
RESTRAINTS
Side)
COMPONENTS

SB
PACKAGE TRAY TRIM

PANEL ASSEMBLY
DECK BOARD
SUB-ASSEMBLY
DECK FLOOR BOX
REAR SEAT ASSEMBLY
NO. 1 REAR SEAT

LEG COVER
37 (375, 27)
x6 42 (430, 31)
REAR SEAT INNER
BELT ASSEMBLY

B114642E02
SB96 SEAT BELT REAR SEAT INNER BELT ASSEMBLY (for Hatchback RH Side)
SB
REAR SEAT INNER

BELT ASSEMBLY
42 (430, 31)

PAD SUB-ASSEMBLY
B119856E03
SEAT BELT REAR SEAT INNER BELT ASSEMBLY (for Hatchback RH Side) SB97
REMOVAL
NOTICE:
the rear seat.
(for 60/40 Split Seat Type) (See page IR-48)
2. REMOVE DECK BOARD SUB-ASSEMBLY (for 60/40
Split Seat Type) (See page IR-48)
SB
3. REMOVE DECK FLOOR BOX (for 60/40 Split Seat
Type) (See page IR-48)
Seat Type) (See page SE-89)
114)
Band
B114643E01

B119859
SB98 SEAT BELT REAR SEAT INNER BELT ASSEMBLY (for Hatchback RH Side)
INSTALLATION
NOTICE:
rear seat.
SB Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf)
NOTICE:
convex areas of the rear seat back frame.
Convex (2) Install the belt into the band.
Band
B114644E01

NOTICE:
Arrow Mark Locating Mark 4. INSTALL REAR SEAT CUSHION COVER PAD SUB-
B119860E02 ASSEMBLY (for Hold Down Seat Type) (See page SE-
123)
5. INSTALL DECK FLOOR BOX (for 60/40 Split Seat
Type) (See page IR-83)
6. INSTALL DECK BOARD SUB-ASSEMBLY (for 60/40
SEAT BELT REAR SEAT OUTER BELT ASSEMBLY (for Sedan) SB99
REAR SEAT OUTER BELT ASSEMBLY (for Sedan)

SEAT BELT
RESTRAINTS
COMPONENTS
REAR SEAT OUTER SB

BELT ASSEMBLY
REAR CENTER SEAT
OUTER BELT ASSEMBLY
REAR SEATBACK REAR SEAT OUTER

ASSEMBLY RH BELT ASSEMBLY
x2
REAR SEATBACK
ASSEMBLY LH
x2
37 (375, 27)
37 (375, 27)
REAR SEAT INNER BELT

ASSEMBLY RH 37 (375, 27)
37 (375, 27)

ASSEMBLY LH

PAD SUB-ASSEMBLY
B138665E04
SB100 SEAT BELT REAR SEAT OUTER BELT ASSEMBLY (for Sedan)
for Fixed Seat Type:
REAR CENTER SEAT

SB REAR SEAT OUTER
OUTER BELT ASSEMBLY
BELT ASSEMBLY RH
REAR SEAT OUTER

BELT ASSEMBLY LH
7.9 (80, 70 in.*lbf)
x3
REAR SEATBACK
ASSEMBLY
REAR SEAT INNER

BELT ASSEMBLY RH
REAR SEAT INNER

BELT ASSEMBLY LH

PAD SUB-ASSEMBLY

B138611E01
SB
LUGGAGE COMPARTMENT
FLOOR MAT
SPARE WHEEL
COVER ASSEMBLY
LUGGAGE COMPARTMENT
TRIM INNER PAD
for Grand Tire:
LUGGAGE COMPARTMENT
TRIM INNER PAD
B138565E01
w/ Curtain Shield Airbag:
SB
REAR DOOR OPENING ROOF SIDE INNER
TRIM WEATHERSTRIP RH GARNISH RH
REAR SEAT
SIDE COVER RH
ROOF SIDE INNER

REAR DOOR REAR DOOR OPENING GARNISH LH
SCUFF PLATE RH TRIM WEATHERSTRIP LH
REAR SEAT
SIDE COVER LH
REAR DOOR
SCUFF PLATE LH
Non-reusable part
B138449E01
w/o Rear Spoiler:
HIGH MOUNTED STOP

SB
LIGHT ASSEMBLY
HIGH MOUNTED STOP

LIGHT CONNECTOR
x4
PACKAGE TRAY TRIM
PANEL ASSEMBLY
42 (430, 31)
REAR SEAT OUTER

BELT ASSEMBLY
42 (430, 31)
SEAT BELT
HOLE SEAL

B138567E01
REMOVAL
HINT:
TERMINAL (w/o Rear Spoiler)
SB 2. REMOVE REAR SEAT CUSHION COVER PAD SUB-
ASSEMBLY
page SE-46).
page SE-106).
3. REMOVE REAR SEATBACK ASSEMBLY RH (for 60/
40 Split Seat Type) (See page SE-57)
4. REMOVE REAR SEATBACK ASSEMBLY LH (for 60/
5. REMOVE REAR SEATBACK ASSEMBLY (for Fixed
6. REMOVE LUGGAGE COMPARTMENT FLOOR MAT
(for 60/40 Split Seat Type) (See page ED-133)
7. REMOVE SPARE WHEEL COVER ASSEMBLY (for 60/
40 Split Seat Type) (See page ED-133)
8. REMOVE LUGGAGE COMPARTMENT TRIM INNER
PAD (for 60/40 Split Seat Type) (See page ED-134)
9. REMOVE REAR DOOR SCUFF PLATE RH (See page
IR-15)
10. REMOVE REAR DOOR SCUFF PLATE LH (See page
IR-15)
WEATHERSTRIP RH (See page AV-173)
WEATHERSTRIP LH (See page AV-173)
13. REMOVE REAR SEAT SIDE COVER RH (See page IR-
16)
14. REMOVE REAR SEAT SIDE COVER LH (See page IR-
16)
15. REMOVE ROOF SIDE INNER GARNISH RH (See page
IR-16)
16. REMOVE ROOF SIDE INNER GARNISH LH (See page
IR-16)
17. REMOVE HIGH MOUNTED STOP LIGHT ASSEMBLY
(w/o Rear Spoiler) (See page LI-141)

(See page AV-173)
(a) Remove the bolt.
(b) Disengage the 2 claws and remove the anchor
plate.
SB
B134917
(c) Remove the bolt, the hook and the retractor.
B134918
20. REMOVE SEAT BELT HOLE SEAL

hole seal.
B134919
INSTALLATION
HINT:
1. INSTALL SEAT BELT HOLE SEAL
(a) Engage the 2 claws and install the seat belt hole
SB seal.
B134919

retractor.
Unlock (1) Gently incline the retractor from its initial
position. Check that the belt does not lock
direction.
Also, check that the belt locks when the
45
inclination of the retractor is 45 or more.
NOTICE:
Do not disassemble the retractor.
Lock rear seat outer belt.
B134915E01
(b) Insert the hook into the body hole and install the
retractor with the bolt.
B134918
(c) Engage the 2 claws and install the anchor plate.

(d) Tighten the bolt.
NOTICE:
The check should be performed with the rear
Do not allow the anchor part of the rear seat
outer belt and the protruding parts of the floor
B134917 panel to overlap.
rear seat outer belt.
(See page AV-174)
4. INSTALL HIGH MOUNTED STOP LIGHT ASSEMBLY
(w/o Rear Spoiler) (See page LI-142) SB
5. INSTALL ROOF SIDE INNER GARNISH RH (See page
IR-32)
6. INSTALL ROOF SIDE INNER GARNISH LH (See page
IR-33)
7. INSTALL REAR SEAT SIDE COVER RH (See page IR-
33)
8. INSTALL REAR SEAT SIDE COVER LH (See page IR-
33)
11. INSTALL REAR DOOR SCUFF PLATE RH (See page
IR-34)
12. INSTALL REAR DOOR SCUFF PLATE LH (See page
IR-34)
13. INSTALL LUGGAGE COMPARTMENT TRIM INNER
14. INSTALL SPARE WHEEL COVER ASSEMBLY (for 60/
15. INSTALL LUGGAGE COMPARTMENT FLOOR MAT
16. INSTALL REAR SEATBACK ASSEMBLY RH (for 60/
17. INSTALL REAR SEATBACK ASSEMBLY LH (for 60/40
18. INSTALL REAR SEATBACK ASSEMBLY (for Fixed
ASSEMBLY
page SE-53).
page SE-109).

SB
SB108 SEAT BELT REAR SEAT OUTER BELT ASSEMBLY (for Hatchback 5 Door)
REAR SEAT OUTER BELT ASSEMBLY (for Hatchback 5

SEAT BELT
RESTRAINTS
Door)
COMPONENTS
SB
PACKAGE TRAY TRIM

PANEL ASSEMBLY
DECK BOARD
SUB-ASSEMBLY
DECK FLOOR BOX
DECK FLOOR BOX
B127707E02
SEAT BELT REAR SEAT OUTER BELT ASSEMBLY (for Hatchback 5 Door) SB109
REAR SEAT
ASSEMBLY
NO. 1 REAR SEAT
LEG COVER SB
37 (375, 27)
REAR SEAT
x6 ASSEMBLY
NO. 2 REAR SEAT

LEG COVER
NO. 1 REAR SEAT 37 (375, 27)

LEG COVER x7
REAR SEATBACK
ASSEMBLY
PAD SUB-ASSEMBLY
37 (375, 27)
x4
B121713E05
SB
42 (430, 31)
ROOF SIDE INNER GARNISH
REAR CENTER SEAT

OUTER BELT ASSEMBLY
DECK TRIM SIDE

PANEL ASSEMBLY
REAR SEAT OUTER 42 (430, 31)

BELT ASSEMBLY
x2
REAR DOOR OPENING REAR SEAT SHOULDER
TRIM WEATHERSTRIP BELT HANGER
42 (430, 31)
SEAT BELT
HOLE SEAL x2
REAR DOOR SCUFF PLATE
REAR DECK
TRIM COVER
Non-reusable part
B114430E02
REMOVAL
CAUTION:
the rear seat.
HINT:
otherwise specified. SB
TERMINAL (for LH Side)
(See page IR-48)
IR-48)
(a) for RH Side:
(b) for LH Side:
HINT:
Split Seat Type)
(a) for RH Side:
page SE-89).
(b) for LH Side:
page SE-70).
Seat Type)
(a) for RH Side:
89).
(b) for LH Side:
71).
114)
51)

WEATHERSTRIP
the extent that the deck trim side panel and roof side
inner garnish can be removed.
12. REMOVE REAR DECK TRIM COVER (See page IR-49)
SB
B114431
13. REMOVE DECK TRIM SIDE PANEL ASSEMBLY

(a) Remove the belt of the rear seat outer belt from the
rear seat shoulder belt hanger.
B114289
(b) Remove the bolt.

(c) Disengage the clip and remove the anchor plate of
the rear seat outer belt.
B130498
(d) for RH side:

(1) Remove the 3 screws.
(2) Disengage the 3 clips and the 6 claws and
remove the deck trim side panel.
B114573
(e) for LH side:

(2) Disengage the 3 clips and the 6 claws.
(3) Disconnect the luggage compartment room
light connector and remove the deck trim side
panel.
SB
B114574
14. REMOVE REAR SEAT SHOULDER BELT HANGER

(a) Using a screwdriver with its tip wrapped in
protective tape, disengage the 2 claws and remove
the rear seat shoulder belt hanger.
Protective Tape
B114433E01
15. REMOVE REAR CENTER SEAT OUTER BELT

ASSEMBLY (for RH Side)
the center belt guide.
Protective Tape
B114462E01
16. REMOVE ROOF SIDE INNER GARNISH

(a) for RH Side (w/ Curtain Shield Airbag):
NOTICE:
Replace the special clip with a new one because
it is damaged when the roof side inner garnish
is removed.
(1) Disengage the 5 clips.
Special Clip (2) Pass the rear seat outer and rear center seat
SB outer belts through the slit in the roof side inner
garnish and remove the roof side inner garnish.
B114576E01
(b) for RH Side (w/o Curtain Shield Airbag):

(2) Pass the rear seat outer and rear center seat
outer belts through the slit in the roof side inner
B114575
(c) for LH Side (w/ Curtain Shield Airbag):

NOTICE:
it is damaged when the roof side inner garnish
is removed.
(2) Pass the rear seat outer belt through the slit in
Special Clip the roof side inner garnish and remove the roof
side inner garnish.
B114578E01
(d) for LH Side (w/o Curtain Shield Airbag):

the roof side inner garnish and remove the roof
side inner garnish.
B114577

(a) Remove the bolt and the through anchor.
SB
B114434
(b) Remove the bolt, the 2 hooks and the retractor.
B114435

hole seal.
B114436
INSTALLATION
CAUTION:
rear seat.
HINT:
SB otherwise specified.
seal.
B114436

Unlock (a) Check the angle of inclination required to lock the
45 retractor.
NOTICE:
hooks and install the retractor with the bolt.
B114435
(c) Install the through anchor with the bolt.

(d) Check that the ELR locks.
NOTICE:
Perform the check with the rear seat outer belt
installed.
B114434 rear seat outer belt.
3. INSTALL ROOF SIDE INNER GARNISH

(1) Install a new special clip.
garnish.
(3) Engage the 5 clips and install the roof side
Special Clip inner garnish.
SB
B114576E01

garnish.
inner garnish.
B114575

the roof side inner garnish.
inner garnish.
Special Clip
B114578E01

inner garnish.
B114577
4. INSTALL REAR CENTER SEAT OUTER BELT

ASSEMBLY (for RH Side)
(a) Engage the 4 claws and install the center belt guide.
SB
B114468
5. INSTALL REAR SEAT SHOULDER BELT HANGER

(a) Engage the 2 claws and install the rear seat
shoulder belt hanger.
B119901
6. INSTALL DECK TRIM SIDE PANEL ASSEMBLY

(a) for RH Side:
(1) Engage the 3 clips and the 6 claws and install
the deck trim side panel.
(2) Tighten the 3 screws.
B114573
(b) for LH Side:

(1) Connect the luggage compartment room light
connector.
SB
B114574
(c) Engage the clip and install the anchor plate of the
B130498
(e) Install the belt of the rear seat outer belt into the rear
seat shoulder belt hanger.
7. INSTALL REAR DECK TRIM COVER (See page IR-82)
B114289

WEATHERSTRIP
80)
Seat Type)
(a) for RH Side:
B114431 (1) Install the rear seat assembly (See page SE-
102).
(b) for LH Side:

84).
Split Seat Type)
SB (a) for RH Side:
SE-103).
(b) for LH Side:
SE-85).
123)
(a) for RH Side:
(1) Install the deck floor box (See page IR-83).
(b) for LH Side:
HINT:
IR-83)
(See page IR-83)
REAR SEAT OUTER BELT ASSEMBLY (for Hatchback 3

SEAT BELT
RESTRAINTS
Door)
COMPONENTS
SB
PACKAGE TRAY TRIM

PANEL ASSEMBLY
DECK BOARD
SUB-ASSEMBLY
DECK FLOOR BOX
DECK FLOOR BOX
B127707E02
REAR SEAT
ASSEMBLY
NO. 1 REAR SEAT
SB LEG COVER
37 (375, 27)
REAR SEAT
x6 ASSEMBLY
NO. 2 REAR SEAT

LEG COVER
NO. 1 REAR SEAT 37 (375, 27)

LEG COVER x7
REAR SEATBACK
ASSEMBLY
PAD SUB-ASSEMBLY
37 (375, 27)
x4
B121713E05
FRONT DOOR OPENING

REAR SEAT SHOULDER
TRIM WEATHERSTRIP
BELT HANGER SB
FRONT QUARTER TRIM
PANEL ASSEMBLY

FRONT DOOR
SCUFF PLATE
42 (430, 31)
REAR CENTER SEAT

OUTER BELT ASSEMBLY
ROOF SIDE INNER GARNISH
42 (430, 31)
REAR SEAT OUTER
BELT ASSEMBLY x2
DECK TRIM SIDE

PANEL ASSEMBLY
42 (430, 31)
x2
SEAT BELT HOLE SEAL
REAR DECK
N*m (kgf*cm, ft*lbf) : Specified torque TRIM COVER
Non-reusable part
B114481E02
REMOVAL
NOTICE:
the rear seat.
HINT:
SB otherwise specified.
(See page IR-48)
IR-48)
(a) for RH Side:
(b) for LH Side:
HINT:
Split Seat Type)
(a) for RH Side:
page SE-89).
(b) for LH Side:
page SE-70).
Seat Type)
(a) for RH Side:
89).
(b) for LH Side:
71).
114)
97)
WEATHERSTRIP (See page SB-76)
12. REMOVE REAR SEAT SHOULDER BELT HANGER

(a) Remove the belt of the rear seat outer belt.
SB
B114498
(b) Using a screwdriver with its tip wrapped in

the rear seat shoulder belt hanger.
Protective Tape
B114484E01

ASSEMBLY
(a) Disengage the 8 clips, the retainer and the 10 claws
and remove the front quarter trim panel.
B114499
15. REMOVE DECK TRIM SIDE PANEL ASSEMBLY

(a) Remove the bolt.
(b) Disengage the clip and the anchor plate of the rear
seat outer belt.
B114500
(c) for RH Side:

(2) Disengage the 3 clips and the 3 claws and
remove the deck trim side panel.
SB
B114501
(d) for LH Side:

(2) Disengage the 3 clips and the 3 claws.
(3) Disconnect the luggage compartment room
light connector and remove the deck trim side
panel.
ASSEMBLY (for RH Side) (See page SB-113)
B114502
17. REMOVE ROOF SIDE INNER GARNISH

NOTICE:
Special Clip it is damaged when the roof side inner garnish
is removed.
(1) Disengage the 4 clips and the claw.
B114504E01

SB
B114505

NOTICE:
Special Clip it is damaged when the roof side inner garnish
is removed.
side inner garnish.
B114506E01

side inner garnish.
B114507

(a) Remove the bolt and the through anchor.
B114482
(b) Remove the bolt, the 2 hooks and the retractor.
SB
B114483

hole seal.
B114436
INSTALLATION
NOTICE:
rear seat.
HINT:
otherwise specified. SB
seal.
B114436

Unlock (a) Check the angle of inclination required to lock the
45 retractor.
NOTICE:
B114483
(c) Install the through anchor with the bolt.

NOTICE:
Perform the check with the rear seat outer belt
installed.
B114482 rear seat outer belt.
3. INSTALL ROOF SIDE INNER GARNISH

Special Clip outer belts through the slit in the roof side inner
garnish.
(3) Engage the 4 clips and the claw and install the
roof side inner garnish.
SB
B114504E01

garnish.
B114505

Special Clip the roof side inner garnish.
B114506E01

ASSEMBLY (for RH Side) (See page SB-117)
B114507
5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY

(a) for RH Side:
SB
B114501
(b) for LH Side:

(1) Connect the luggage compartment room light
connector.
B114502
(c) Engage the clip and install the anchor plate of the
B114500

(a) Engage the 8 clips, the retainer and the 10 claws
and install the front quarter trim panel.
SB
B114499
8. INSTALL REAR SEAT SHOULDER BELT HANGER

shoulder belt hanger.
B117737
(b) Install the belt of the rear seat outer belt.

WEATHERSTRIP (See page SB-80)
119)
Seat Type)
(a) for RH Side:
B114498
102).
(b) for LH Side:
84).
Split Seat Type)
(a) for RH Side:
(1) Install the No. 1 rear seat leg cover (See
pageSE-103 ).
(b) for LH Side:
SE-85).

123)
(a) for RH Side:
(1) Install the deck floor box (See page IR-83). SB
(b) for LH Side:
HINT:
IR-83)
(See page IR-83)
SB134 SEAT BELT REAR CENTER SEAT INNER BELT ASSEMBLY (for Sedan)
REAR CENTER SEAT INNER BELT ASSEMBLY (for Sedan)

SEAT BELT
RESTRAINTS
COMPONENTS
SB
REAR CENTER SEAT

INNER BELT ASSEMBLY
REAR CENTER SEAT

INNER BELT ASSEMBLY
REAR SEAT CUSHION

42 (430, 31)
42 (430, 31)
B138566E03
SEAT BELT REAR CENTER SEAT INNER BELT ASSEMBLY (for Sedan) SB135
REMOVAL
ASSEMBLY
page SE-46).
page SE-106).
SB
2. REMOVE REAR CENTER SEAT INNER BELT
ASSEMBLY
(1) Remove the bolt and the rear center seat inner
belt.
B134907
(b) for LH Side:

belt.
B134904
INSTALLATION
1. INSTALL REAR CENTER SEAT INNER BELT
ASSEMBLY
(1) Install the rear center seat inner belt with the
bolt.
NOTICE:
Arrow Mark
Locating Mark
B134908E01
SB136 SEAT BELT REAR CENTER SEAT INNER BELT ASSEMBLY (for Sedan)
(b) for LH Side:

bolt.
NOTICE:
SB locating mark area of the floor panel.
ASSEMBLY
Arrow Mark
Locating Mark page SE-53).
B134905E01 (b) for Fixed Seat Type:
page SE-109).
SEAT BELT REAR CENTER SEAT INNER BELT ASSEMBLY (for Hatchback LH Side) SB137
REAR CENTER SEAT INNER BELT ASSEMBLY (for

SEAT BELT
RESTRAINTS
Hatchback LH Side)
COMPONENTS

SB
NO. 1 REAR SEAT REAR CENTER SEAT
LEG COVER
42 (430, 31) INNER BELT ASSEMBLY
NO. 2 REAR SEAT

LEG COVER
37 (375, 27)
x3 REAR SEAT CUSHION
ASSEMBLY

REAR CENTER SEAT
INNER BELT ASSEMBLY

PAD SUB-ASSEMBLY
37 (375, 27)
B114645E03
SB138 SEAT BELT REAR CENTER SEAT INNER BELT ASSEMBLY (for Hatchback LH Side)
REMOVAL
NOTICE:
the rear seat.
SB 2. REMOVE NO. 2 REAR SEAT LEG COVER (for 60/40

114)
ASSEMBLY
(1) Using "Torx" socket wrench E10, remove the 3
bolts and pull up the rear seat cushion.
B114740

belt.
Band
B114651E01

belt.
B119857
SEAT BELT REAR CENTER SEAT INNER BELT ASSEMBLY (for Hatchback LH Side) SB139
INSTALLATION
NOTICE:
rear seat.
ASSEMBLY
(a) for 60/40 Split Seat Type
(1) Install the rear center seat inner belt with the SB
bolt.
NOTICE:
Band
Convex
convex areas of the rear seat back frame.
B114652E01 (2) Install the belt into the band.
(3) Install the rear seat cushion.

(4) Using "Torx" socket wrench E10, tighten the 3
bolts in the sequence shown in the illustration.
2 1
B114740E01

bolt.
NOTICE:
Arrow Mark Locating Mark Split Seat Type) (See page SE-85)
B119858E02 4. INSTALL REAR SEAT CUSHION COVER PAD SUB-
123)
SB140 SEAT BELT REAR CENTER SEAT INNER BELT ASSEMBLY (for Hatchback RH Side)
REAR CENTER SEAT INNER BELT ASSEMBLY (for

SEAT BELT
RESTRAINTS
Hatchback RH Side)
COMPONENTS

SB
PACKAGE TRAY TRIM

PANEL ASSEMBLY
DECK BOARD
SUB-ASSEMBLY
DECK FLOOR BOX
42 (430, 31)
REAR CENTER SEAT

INNER BELT ASSEMBLY
NO. 2 REAR SEAT

LEG COVER
NO. 1 REAR SEAT

LEG COVER
37 (375, 27)
x7 REAR SEAT ASSEMBLY

B114653E02
SEAT BELT REAR CENTER SEAT INNER BELT ASSEMBLY (for Hatchback RH Side) SB141
SB
REAR CENTER SEAT

INNER BELT ASSEMBLY
42 (430, 31)

PAD SUB-ASSEMBLY
B119856E05
SB142 SEAT BELT REAR CENTER SEAT INNER BELT ASSEMBLY (for Hatchback RH Side)
REMOVAL
NOTICE:
the rear seat.
SB 2. REMOVE DECK BOARD SUB-ASSEMBLY (for 60/40

3. REMOVE DECK FLOOR BOX (for 60/40 Split Seat
Type)
HINT:
Use the same procedure as for the RH side (See page
IR-48).
114)
ASSEMBLY
belt.
B114654

belt.
B119859
SEAT BELT REAR CENTER SEAT INNER BELT ASSEMBLY (for Hatchback RH Side) SB143
INSTALLATION
NOTICE:
rear seat.
ASSEMBLY
(1) Install the rear center seat inner belt with the SB
bolt.
NOTICE:
Convex convex area of the rear seat back frame.
B114655E01

bolt.
NOTICE:
Arrow Mark Locating Mark Split Seat Type) (See page SE-85)
B119860E02 4. INSTALL NO. 1 REAR SEAT LEG COVER (for 60/40
123)
6. INSTALL DECK FLOOR BOX (for 60/40 Split Seat
Type)
HINT:
Use the same procedure as for the RH side (See page
IR-83).
7. INSTALL DECK BOARD SUB-ASSEMBLY (for 60/40
SB144 SEAT BELT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Sedan)
REAR CENTER SEAT OUTER BELT ASSEMBLY (for Sedan)

SEAT BELT
RESTRAINTS
COMPONENTS
SB REAR SEAT OUTER

BELT ASSEMBLY
REAR CENTER SEAT
OUTER BELT ASSEMBLY
REAR SEATBACK REAR SEAT OUTER

ASSEMBLY RH BELT ASSEMBLY
x2
REAR SEATBACK
ASSEMBLY LH
x2
37 (375, 27)
37 (375, 27)

ASSEMBLY RH 37 (375, 27)
37 (375, 27)

ASSEMBLY LH

PAD SUB-ASSEMBLY
B138665E04
SEAT BELT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Sedan) SB145
for Fixed Seat Type:
REAR CENTER SEAT

REAR SEAT OUTER
OUTER BELT ASSEMBLY
SB
BELT ASSEMBLY RH
REAR SEAT OUTER

BELT ASSEMBLY LH
7.9 (80, 70 in.*lbf)
x3
REAR SEATBACK
ASSEMBLY
REAR SEAT INNER

BELT ASSEMBLY RH
REAR SEAT INNER

BELT ASSEMBLY LH

PAD SUB-ASSEMBLY

B138611E01
SB
LUGGAGE COMPARTMENT
FLOOR MAT
SPARE WHEEL
COVER ASSEMBLY
LUGGAGE COMPARTMENT
TRIM INNER PAD
for Grand Tire:
LUGGAGE COMPARTMENT
TRIM INNER PAD
B138565E01
SB
REAR DOOR OPENING ROOF SIDE INNER
TRIM WEATHERSTRIP RH GARNISH RH
REAR SEAT
SIDE COVER RH
ROOF SIDE INNER

REAR DOOR REAR DOOR OPENING GARNISH LH
SCUFF PLATE RH TRIM WEATHERSTRIP LH
REAR SEAT
SIDE COVER LH
REAR DOOR
SCUFF PLATE LH
Non-reusable part
B138449E01
w/o Rear Spoiler:
SB
HIGH MOUNTED STOP
LIGHT ASSEMBLY
HIGH MOUNTED STOP

LIGHT CONNECTOR
PACKAGE TRAY TRIM x4

PANEL ASSEMBLY
42 (430, 31)
42 (430, 31)
REAR CENTER SEAT

OUTER BELT ASSEMBLY
REAR CENTER SEAT

OUTER BELT ASSEMBLY
42 (430, 31)

B138564E02
REMOVAL
ASSEMBLY
page SE-46). SB
page SE-106).
3. REMOVE REAR SEATBACK ASSEMBLY RH (for 60/
4. REMOVE REAR SEATBACK ASSEMBLY LH (for 60/
5. REMOVE REAR SEATBACK ASSEMBLY (for Fixed
6. REMOVE LUGGAGE COMPARTMENT FLOOR MAT
7. REMOVE SPARE WHEEL COVER ASSEMBLY (for 60/
8. REMOVE LUGGAGE COMPARTMENT TRIM INNER
IR-15)
IR-15)
13. REMOVE REAR SEAT SIDE COVER RH (See page IR-
16)
14. REMOVE REAR SEAT SIDE COVER LH (See page IR-
16)
15. REMOVE ROOF SIDE INNER GARNISH RH (See page
IR-16)
IR-16)
17. REMOVE HIGH MOUNTED STOP LIGHT ASSEMBLY
(See page AV-173)

ASSEMBLY
(a) for Fixed Seat Type:
(1) Remove the bolt and the anchor plate.
SB
B138451
(b) Remove the bolt, the hook and the retractor.
B134914
INSTALLATION
Unlock ASSEMBLY
retractor.
45 when the retractor is inclined 15 or less in any
NOTICE:
Lock Do not disassemble the retractor.
rear center seat outer belt.
B134915E01
(b) Insert the hook into the body hole and install the
retractor with the bolt.
B134914
(c) for Fixed Seat Type:

(1) Install the anchor plate with the bolt.
NOTICE:
(d) Check that the ELR locks. SB
NOTICE:
The check should be performed with the rear
Do not allow the anchor part of the rear seat
Arrow Mark outer belt and the protruding parts of the floor
Locating Mark
panel to overlap.
B138452E01
(See page AV-174)
3. INSTALL HIGH MOUNTED STOP LIGHT ASSEMBLY
4. INSTALL ROOF SIDE INNER GARNISH RH (See page
IR-32)
IR-33)
6. INSTALL REAR SEAT SIDE COVER RH (See page IR-
33)
7. INSTALL REAR SEAT SIDE COVER LH (See page IR-
33)
IR-34)
IR-34)
12. INSTALL LUGGAGE COMPARTMENT TRIM INNER
13. INSTALL SPARE WHEEL COVER ASSEMBLY (for 60/
14. INSTALL LUGGAGE COMPARTMENT FLOOR MAT
15. INSTALL REAR SEATBACK ASSEMBLY RH (for 60/
16. INSTALL REAR SEATBACK ASSEMBLY LH (for 60/40

17. INSTALL REAR SEATBACK ASSEMBLY (for Fixed
ASSEMBLY
SB (1) Install the rear seat cushion cover pad (See
page SE-53).
page SE-109).
SEAT BELT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Hatchback 5 Door) SB153
REAR CENTER SEAT OUTER BELT ASSEMBLY (for

SEAT BELT
RESTRAINTS
Hatchback 5 Door)
COMPONENTS
SB
PACKAGE TRAY TRIM

PANEL ASSEMBLY
DECK BOARD
SUB-ASSEMBLY
DECK FLOOR BOX RH
DECK FLOOR BOX LH
B114273E01
SB154 SEAT BELT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Hatchback 5 Door)
REAR SEAT
ASSEMBLY RH
NO. 1 REAR SEAT
SB LEG COVER
37 (375, 27) REAR SEAT

x6 ASSEMBLY LH
NO. 2 REAR SEAT

LEG COVER
NO. 1 REAR SEAT 37 (375, 27)

LEG COVER x7
REAR SEATBACK
ASSEMBLY
PAD SUB-ASSEMBLY
37 (375, 27)
x4
B121713E03
SB
42 (430, 31)
ROOF SIDE INNER

GARNISH RH
42 (430, 31)
42 (430, 31)
DECK TRIM SIDE
PANEL ASSEMBLY RH
REAR CENTER SEAT x2
OUTER BELT ASSEMBLY
REAR DOOR OPENING

TRIM WEATHERSTRIP RH
42 (430, 31)
x2
REAR DOOR
SCUFF PLATE RH REAR DECK
REAR SEAT OUTER TRIM COVER
BELT ASSEMBLY RH
Non-reusable part
B114457E02
REAR SEAT SHOULDER

BELT COVER
SB
SEAT BELT
ANCHOR COVER
ROOF HEADLINING ASSEMBLY
ROOF SIDE INNER

REAR SEAT OUTER
GARNISH LH
REAR DOOR OPENING BELT ASSEMBLY LH
TRIM WEATHERSTRIP LH
42 (430, 31) x2
DECK TRIM SIDE PANEL

ASSEMBLY LH
REAR DOOR
SCUFF PLATE LH
LUGGAGE COMPARTMENT
ROOM LIGHT CONNECTOR
Non-reusable part
B114458E03
REMOVAL
CAUTION:
the rear seat.
TERMINAL
(See page IR-48)
SB
IR-48)
4. REMOVE DECK FLOOR BOX RH (See page IR-48)
5. REMOVE DECK FLOOR BOX LH (See page IR-48)
Split Seat Type)
(a) for RH side:
page SE-89).
(b) for LH side:
page SE-70).
8. REMOVE REAR SEAT ASSEMBLY RH (for 60/40 Split
9. REMOVE REAR SEAT ASSEMBLY LH (for 60/40 Split
114)
IR-51)
IR-51)
WEATHERSTRIP RH (See page SB-112)
WEATHERSTRIP LH
HINT:
17. REMOVE REAR SEAT OUTER BELT ASSEMBLY RH
(See page IR-51)
18. REMOVE REAR SEAT OUTER BELT ASSEMBLY LH
(See page IR-51)
19. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

(See page IR-52)
20. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
(See page IR-52)
21. REMOVE ROOF SIDE INNER GARNISH RH
SB the center belt guide.
Protective Tape
B114462E01
(b) w/ Curtain Shield Airbag:

NOTICE:
Replace the special clip with a new one when
the roof side inner garnish is removed.
(2) Pass the rear seat outer belt and the rear
center seat outer belt through the slit in the roof
Special Clip side inner garnish and remove the roof side
inner garnish.
B114576E01
(c) w/o Curtain Shield Airbag:

side inner garnish and remove the roof side
inner garnish.
IR-54)
B114575

ASSEMBLY
(a) Remove the 2 tongue plates.
B114459

protective tape, disengage the 2 claws and open the
slip joint cover.
Protective Tape SB
B114460E01
B114461
(d) Remove the bolt, the hook and the bracket.
B114463
(e) Remove the bolt, the 2 hooks and the retractor.
B114551
24. REMOVE SEAT BELT ANCHOR COVER

(a) Using a moulding remover, disengage the 4 claws
and remove the seat belt anchor cover.
B114464
25. REMOVE ROOF HEADLINING ASSEMBLY

(a) Using a clip remover, remove the clip and the roof
headlining.
SB
B114465
26. REMOVE REAR SEAT SHOULDER BELT COVER

(a) Disengage the 2 claws and remove the rear seat
shoulder belt cover.
B114466
INSTALLATION
CAUTION:
rear seat.
1. INSTALL REAR SEAT SHOULDER BELT COVER
shoulder belt cover.
SB
B114466
2. INSTALL ROOF HEADLINING ASSEMBLY

(a) Install the roof headlining with the clip.
B114465
3. INSTALL SEAT BELT ANCHOR COVER

cover.
B114467

Unlock ASSEMBLY
45 (a) Check the angle of inclination required to lock the
retractor.
Lock (1) Gently incline the retractor from its initial
B114437E01 NOTICE:
Do not disassemble the retractor.
SB
B114551
(c) Insert the hook into the body hole and install the
bracket with the bolt.
NOTICE:
Perform the check with the rear center seat
outer belt installed.
B114463 If the operation is not as specified, replace the
(e) Install the through anchor with the bolt.
B114461
(f) Engage the 2 claws and close the slip joint cover.
B114469
(g) Install the 2 tongue plates.
B114459
5. INSTALL ROOF SIDE INNER GARNISH RH

(a) w/ Curtain Shield Airbag:
side inner garnish.
Special Clip inner garnish.
SB
B114576E01
(b) w/o Curtain Shield Airbag:

side inner garnish.
inner garnish.
B114575
(c) Engage the 4 claws and install the center belt guide.
IR-77)
7. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
(See page IR-79)
8. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
(See page IR-79)
B114468 9. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH
(See page IR-79)
10. INSTALL REAR SEAT OUTER BELT ASSEMBLY LH
(See page IR-80)
WEATHERSTRIP LH
HINT:
IR-80)
IR-80)
16. INSTALL REAR SEAT ASSEMBLY LH (for 60/40 Split

17. INSTALL REAR SEAT ASSEMBLY RH (for 60/40 Split
SB Split Seat Type)
(a) for RH Side:
SE-103).
(b) for LH Side:
SE-85).
123)
22. INSTALL DECK FLOOR BOX RH (See page IR-83)
23. INSTALL DECK FLOOR BOX LH (See page IR-83)
IR-83)
(See page IR-83)
TERMINAL
REAR CENTER SEAT OUTER BELT ASSEMBLY (for

SEAT BELT
RESTRAINTS
Hatchback 3 Door)
COMPONENTS
SB
PACKAGE TRAY TRIM

PANEL ASSEMBLY
DECK BOARD
SUB-ASSEMBLY
DECK FLOOR BOX RH
DECK FLOOR BOX LH
B114273E01
REAR SEAT
ASSEMBLY RH
NO. 1 REAR SEAT
SB LEG COVER
37 (375, 27) REAR SEAT

x6 ASSEMBLY LH
NO. 2 REAR SEAT

LEG COVER
NO. 1 REAR SEAT 37 (375, 27)

LEG COVER x7
REAR SEATBACK
ASSEMBLY
PAD SUB-ASSEMBLY
37 (375, 27)
x4
B121713E03
SB
FRONT DOOR OPENING FRONT QUARTER TRIM

TRIM WEATHERSTRIP RH PANEL ASSEMBLY RH
FRONT DOOR
SCUFF PLATE RH
FRONT DOOR OPENING FRONT QUARTER TRIM

TRIM WEATHERSTRIP LH PANEL ASSEMBLY LH
FRONT DOOR
SCUFF PLATE LH
B114485E01
SB
42 (430, 31)
ROOF SIDE INNER

GARNISH RH
42 (430, 31)
42 (430, 31)
REAR CENTER SEAT

OUTER BELT ASSEMBLY x2
DECK TRIM SIDE

PANEL ASSEMBLY RH
REAR SEAT OUTER 42 (430, 31)

BELT ASSEMBLY RH
x2
REAR DECK
TRIM COVER
Non-reusable part
B114486E02
REAR SEAT SHOULDER

BELT COVER
SB
SEAT BELT
ANCHOR COVER
ROOF HEADLINING
ASSEMBLY
ROOF SIDE INNER

GARNISH LH
REAR SEAT OUTER

BELT ASSEMBLY LH
42 (430, 31)
LUGGAGE COMPARTMENT
ROOM LIGHT CONNECTOR
DECK TRIM SIDE

PANEL ASSEMBLY LH
Non-reusable part
B114487E02
REMOVAL
NOTICE:
the rear seat.
TERMINAL
SB 2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY

(See page IR-48)
IR-48)
Split Seat Type)
(a) for RH Side:
page SE-89).
(b) for LH Side:
page SE-70).
8. REMOVE REAR SEAT ASSEMBLY RH (for 60/40 Split
9. REMOVE REAR SEAT ASSEMBLY LH (for 60/40 Split
114)
12. REMOVE FRONT DOOR SCUFF PLATE RH (See page
IR-97)
13. REMOVE FRONT DOOR SCUFF PLATE LH (See page
IR-97)
WEATHERSTRIP LH
HINT:
ASSEMBLY RH (See page IR-97)
ASSEMBLY LH (See page IR-97)
19. REMOVE REAR SEAT OUTER BELT ASSEMBLY RH

(See page IR-98)
20. REMOVE REAR SEAT OUTER BELT ASSEMBLY LH
(See page IR-98)
21. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
(See page IR-98)
22. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
(See page IR-98)
SB
23. REMOVE ROOF SIDE INNER GARNISH RH
the center belt guide.
Protective Tape
B114462E01
(b) w/ Curtain shield Airbag:

NOTICE:
Replace the special clip with a new one when
the roof side inner garnish is removed.
Special Clip (1) Disengage the 4 clips and the claw.
inner garnish.
B114504E01
(c) w/o Curtain Shield Airbag:

inner garnish.
IR-100)
B114505 25. REMOVE REAR CENTER SEAT OUTER BELT
ASSEMBLY (See page SB-158)
26. REMOVE SEAT BELT ANCHOR COVER (See page
SB-159)
27. REMOVE ROOF HEADLINING ASSEMBLY (See page
SB-160)
28. REMOVE REAR SEAT SHOULDER BELT COVER

(See page SB-160)
SB
INSTALLATION
CAUTION:
rear seat.
1. INSTALL REAR SEAT SHOULDER BELT COVER (See
page SB-160)
2. INSTALL ROOF HEADLINING ASSEMBLY (See page
SB-160)
SB
3. INSTALL SEAT BELT ANCHOR COVER (See page
SB-160)
ASSEMBLY (See page SB-161)
5. INSTALL ROOF SIDE INNER GARNISH RH
(a) w/ Curtain Shield Airbag:
(1) Install a new special clip onto the roof side
inner garnish.
Special Clip (2) Pass the rear seat outer belt and the rear
side inner garnish.
B114504E01
(b) w/o Curtain Shield Airbag:

side inner garnish.
B114505
(c) Engage the 4 claws and install the center belt guide.
IR-116)
7. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
(See page IR-117)
8. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
(See page IR-118)
B114468 9. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH
(See page IR-118)
10. INSTALL REAR SEAT OUTER BELT ASSEMBLY LH

(See page IR-118)
RH (See page IR-118)
LH (See page IR-119)
SB
WEATHERSTRIP LH
HINT:
16. INSTALL FRONT DOOR SCUFF PLATE RH (See page
IR-119)
17. INSTALL FRONT DOOR SCUFF PLATE LH (See page
IR-119)
18. INSTALL REAR SEAT ASSEMBLY LH (for 60/40 Split
19. INSTALL REAR SEAT ASSEMBLY RH (for 60/40 Split
Split Seat Type)
(a) for RH Side:
SE-103).
(b) for LH Side:
SE-85).
123)
IR-83)
(See page IR-83)
TERMINAL
SEAT BELT CHILD RESTRAINT SEAT ANCHOR BRACKET (for Sedan) SB175
CHILD RESTRAINT SEAT ANCHOR BRACKET (for Sedan)

SEAT BELT
RESTRAINTS
COMPONENTS
SB
x3 42 (430, 31)
x3 CHILD RESTRAINT SEAT

TETHER ANCHOR BRACKET
B138377E01
SB176 SEAT BELT CHILD RESTRAINT SEAT ANCHOR BRACKET (for Sedan)
REMOVAL
1. REMOVE CHILD RESTRAINT SEAT TETHER
ANCHOR BRACKET
HINT:
Use the same procedure to remove all the child restraint
seat tether anchor brackets.
(a) Disengage the claw and open the package tray trim
SB cover.
B138378
(b) Remove the bolt and the child restraint seat tether
anchor bracket.
B138530
SEAT BELT CHILD RESTRAINT SEAT ANCHOR BRACKET (for Sedan) SB177
INSTALLATION
1. INSTALL CHILD RESTRAINT SEAT TETHER
ANCHOR BRACKET
HINT:
Use the same procedure to install all the child restraint
seat tether anchor brackets.
child restraint seat tether anchor bracket with the
bolt.
SB
B138379
(b) Engage the claw and close the package tray rim
cover.
B138378
SEAT FRONT SEAT ASSEMBLY (for Sedan) SE1
FRONT SEAT ASSEMBLY (for Sedan)

SEAT
BODY
COMPONENTS
FRONT SEAT HEADREST

ASSEMBLY
FRONT SEAT
ASSEMBLY
37 (375, 27)
x4
BUCKLE SWITCH
CONNECTOR
SE
for Front Seat Side Airbag:
BUCKLE SWITCH
CONNECTOR
AIRBAG
CONNECTOR

B138550E01
SE2 SEAT FRONT SEAT ASSEMBLY (for Sedan)
FRONT SEAT HEADREST

SUPPORT
FRONT SEATBACK
COVER PAD
FRONT SEAT CUSHION

COVER PAD
x5
FRONT SEAT INNER

BELT ASSEMBLY x2
42 (430, 31)
RECLINING ADJUSTER
RELEASE HANDLE
FRONT SEAT CUSHION

INNER SHIELD FRONT SEAT CUSHION
SE OUTER SHIELD
w/ Vertical Adjuster:
VERTICAL ADJUSTER
KNOB VERTICAL ADJUSTER
x2 COVER
Non-reusable part
B138552E01
RECLINING ADJUSTER
OUTSIDE COVER RH
RECLINING ADJUSTER
OUTSIDE COVER RH
FRONT SEAT CUSHION

LOWER SHIELD RH
FRONT SEAT CUSHION

LOWER SHIELD RH
FRONT SEAT CUSHION

PROTECTOR
FRONT SEAT CUSHION RECLINING ADJUSTER

LOWER SHIELD LH OUTSIDE COVER LH SE
w/ Vertical Adjuster: RECLINING ADJUSTER

OUTSIDE COVER LH
FRONT SEAT CUSHION

LOWER SHIELD LH
VERTICAL ADJUSTER
SPACER
B138608E01
FRONT SEAT ADJUSTER

FRAME ASSEMBLY
SEAT POSITION SENSOR
8.0 (80, 71 in.*lbf)
SEAT POSITION SENSOR

PROTECTOR
SE
OCCUPANT DETECTION ECU
FRONT SEAT WIRE
Non-reusable part
B138553E01
REMOVAL
CAUTION:
NOTICE:
the front seat.
HINT:
TERMINAL
CAUTION:
Seat Side Airbag).
2. REMOVE FRONT SEAT HEADREST ASSEMBLY
(a) Push in the lock button of the front seat headrest
support and remove the front seat headrest.
Lock Button
B138314E01
3. REMOVE FRONT SEAT ASSEMBLY

(a) for Driver Side: SE
(2) w/ Front Seat Side Airbag:
1. Slide the slider and disconnect the airbag
connector.
(3) Disconnect the buckle switch connector.
Slider
B138554E01

connector.
(4) Disconnect the occupant detection ECU
connector.
Slider
B138556E01
(c) Move the front seat to its most rearward position.

(d) Using "Torx" socket wrench E10, remove the 2 bolts
from the front side.
(e) Move the front seat to its most forward position.
(f) Using "Torx" socket wrench E10, remove the 2 bolts
from the rear side.
(g) Remove the front seat.
B138317
SE
DISASSEMBLY
CAUTION:
Wear protective gloves. Sharp surfaces on the front seat
adjuster frame could cause injuries to your hands.
HINT:
(See page SB-33)
2. REMOVE FRONT SEAT CUSHION INNER SHIELD
(a) Remove the screw.
protective tape, disengage the claw and the clip and
remove the front seat cushion outer shield.
Protective Tape
B138327E01
3. REMOVE VERTICAL ADJUSTER COVER (w/ Vertical

Adjuster)
the vertical adjuster cover.
SE
Protective Tape
B138320E01
4. REMOVE VERTICAL ADJUSTER KNOB (w/ Vertical

Adjuster)
(a) Remove the 2 screws and the vertical adjuster
knob.
B138322
5. REMOVE RECLINING ADJUSTER RELEASE

HANDLE
protective tape, disengage the claw and remove the
reclining adjuster release handle.
Protective Tape
B138323E01
6. REMOVE FRONT SEAT CUSHION OUTER SHIELD

protective tape, disengage the 2 claws and the clip
and remove the front seat cushion outer shield.
Protective Tape
B138325E01
7. REMOVE FRONT SEAT CUSHION COVER PAD

(a) Disengage the 2 claws and 7 hooks.
SE
B138330
(b) Using a clip remover, remove the 2 clips and the

front seat cushion cover pad.
B138329
8. REMOVE FRONT SEAT HEADREST SUPPORT

(a) Remove the 3 hog rings.
B138336
(b) Remove the 2 hog rings.
B138334
(c) Disengage the 2 claws and remove the front seat SE

headrest support.
HINT:
Use the same procedure for both sides.
B138332
9. REMOVE FRONT SEATBACK COVER PAD

(a) Remove the front seatback cover pad.
B138338
10. REMOVE VERTICAL ADJUSTER SPACER (w/ Vertical

Adjuster)
(a) Disengage the claw and remove the vertical
adjuster spacer.
B138340
11. REMOVE RECLINING ADJUSTER INSIDE COVER RH

(b) Disengage the claw and remove the reclining
adjuster inside cover.
B138341
12. REMOVE RECLINING ADJUSTER INSIDE COVER LH

(a) w/ Front Seat Side Airbag:
(b) Remove the screw.
(c) Disengage the claw and remove the reclining
B138342
SE 13. REMOVE RECLINING ADJUSTER OUTSIDE COVER

RH
(a) Remove the screw and the reclining adjuster
outside cover.
14. REMOVE RECLINING ADJUSTER OUTSIDE COVER
LH
HINT:
B138343
15. REMOVE FRONT SEAT CUSHION LOWER SHIELD

RH
(a) w/ Vertical Adjuster:
(1) Remove the screw.
(2) Disengage the claw and remove the front seat
cushion lower shield.
B138344
(b) w/o Vertical Adjuster:

(2) Disengage the 2 claws and remove the front
seat cushion lower shield.
B138346

LH
(2) Disengage the 2 claws and remove the front
seat cushion lower shield.
B138345

(2) Disengage the claw and remove the front seat
B138347
17. REMOVE FRONT SEAT CUSHION PROTECTOR SE

(a) Remove the 2 front seat cushion protectors.
B138348
18. REMOVE SEAT POSITION SENSOR PROTECTOR

(for Driver Side)
(a) Disengage the pin and remove the seat position
sensor protector.
B138558
19. REMOVE SEAT POSITION SENSOR (for Driver Side)

(a) Using "Torx" socket wrench T30, remove the bolt
and the seat position sensor.
B138560
20. REMOVE FRONT SEAT WIRE (for Front Passenger

Side)
(a) Disconnect the 5 connectors.
(b) Remove the 2 clamps and the front seat wire
B138562
21. REMOVE OCCUPANT DETECTION ECU (for Front

Passenger Side)
(a) Disengage the claw and remove the occupant
detection ECU.
SE
B138563
REASSEMBLY
CAUTION:
HINT:
The procedure described below is for the driver side of LHD.
Use the same procedure for both the front passenger and
driver sides of LHD, unless otherwise specified.
1. INSTALL SEAT POSITION SENSOR (for Driver Side)
(a) Provisionally install the seat position sensor.
NOTICE:
If the seat position sensor has been
damaged, or there are any cracks, dents or
other defects in the case, bracket or
connector, replace the seat position sensor
with a new one.
When installing the seat position sensor,
make sure that the SRS warning does not
interfere with other parts and is not pinched
Sensor between other parts.
(b) Install a 1 mm (0.04 in.) feeler gauge between the
seat rail and seat position sensor, as shown in the
illustration.
HINT:
Make sure that the clearance between the seat
position sensor and seat rail is within 0.6 to 2 mm
Seat Rail Feeler Gauge (0.023 to 0.079 in.).
(c) Push the top of the seat position sensor toward the
B138561E01 seat rail.
(d) While holding the seat position sensor, tighten the
bolt using "Torx" socket wrench T30.
Torque: 8.0 N*m (80 kgf*cm, 71 in.*lbf) SE
2. INSTALL SEAT POSITION SENSOR PROTECTOR (for

Driver Side)
(a) Engage the pin and install a new seat position
sensor protector.
B138559E01
NOTICE:
Do not damage portion A, shown in the
illustration, when installing the seat position
sensor protector.
3. INSTALL OCCUPANT DETECTION ECU (for Front
Passenger Side)
SE (a) Engage the claw and install the occupant detection
ECU.
B138563
4. INSTALL FRONT SEAT WIRE

(a) Install the front seat wire with the 2 clamps.
(b) Connect the 5 connectors.
B138562
5. INSTALL FRONT SEAT CUSHION PROTECTOR

(a) Install the 2 front seat cushion protectors.
B138348
6. INSTALL FRONT SEAT CUSHION LOWER SHIELD

RH
(1) Engage the claw and install the front seat
(2) Tighten the screw. SE
B138344

(1) Engage the 2 claws and install the front seat
(2) Tighten the screw.
B138346
7. INSTALL FRONT SEAT CUSHION LOWER SHIELD LH

(1) Engage the 2 claws and install the front seat
B138345

(1) Engage the claw and install the front seat
B138347
8. INSTALL RECLINING ADJUSTER OUTSIDE COVER

RH
(a) Install the reclining adjuster outside cover with the
screw.
LH
HINT:
B138343
SE 10. INSTALL RECLINING ADJUSTER INSIDE COVER RH

(a) Engage the claw and install the reclining adjuster
inside cover.
(b) Tighten the screw.
B138341
11. INSTALL RECLINING ADJUSTER INSIDE COVER LH

inside cover.
(c) w/ Front Seat Side Airbag:
(1) Install the clamp.
B138342
12. INSTALL VERTICAL ADJUSTER SPACER (w/ Vertical

Adjuster)
(a) Engage the claw and install the vertical adjuster
spacer.
B138340
13. INSTALL FRONT SEATBACK COVER PAD

(a) Install the front seatback cover pad.
B138338
(b) Using hog ring pliers, install 2 new hog rings.
SE
New Hog Ring
Hog Ring Pliers

B138335E01
(c) Using hog ring pliers, install 3 new hog rings.
New Hog Ring
Hog Ring Pliers

B138337E01
14. INSTALL FRONT SEAT HEADREST SUPPORT

HINT:
(a) Align the protruding portion of the front seat
headrest support with the installation groove of the
Protruding
front seat adjuster frame.
(b) Engage the 2 claws and install the front seat
headrest support.
SE
B138333E01
15. INSTALL FRONT SEAT CUSHION COVER PAD

(a) Install the front seat cushion cover pad with the 2
clips.
B138329
(b) Engage the 2 claws and the 7 hooks.
B138330
16. INSTALL FRONT SEAT CUSHION OUTER SHIELD

(a) Engage the 2 claws and the clip and install the front
seat cushion outer shield.
SE
B138326
17. INSTALL RECLINING ADJUSTER RELEASE HANDLE

release handle.
B138324
18. INSTALL VERTICAL ADJUSTER KNOB (w/ Vertical

Adjuster)
(a) Install the vertical seat adjuster knob.
B138322
19. INSTALL VERTICAL ADJUSTER COVER (w/ Vertical

Adjuster)
(a) Engage the 3 claws and install the vertical adjuster
cover.
B138321
20. INSTALL FRONT SEAT CUSHION INNER SHIELD

(a) Engage the claw and the clip and install the front
seat cushion inner shield.
21. INSTALL FRONT SEAT INNER BELT ASSEMBLY (See
page SB-35)
SE
B138328
INSTALLATION
CAUTION:
NOTICE:
front seat.
HINT:
1. INSTALL FRONT SEAT ASSEMBLY
2 NOTICE:
Follow the procedure described below in order to
prevent the seat tracks from locking separately.
(a) Insert the 2 locating pins through the 2 body holes,
place the front seat in the most forward position,
and then make sure that the inner and outer seat
tracks are locked securely.
(b) Using "Torx" socket wrench E10, tighten bolt 1 and
4 then bolt 2 on the rear side.
(c) Move the front seat to the most rearward position,
3 and then make sure that the inner and outer seat
tracks are locked securely.
1 (d) Using "Torx" socket wrench E10, tighten bolt 3 and
then bolt 4 on the front side.
HINT:
If the inner and outer seat tracks do not lock
simultaneously, loosen the bolts and adjust the seat
SE
B138318E01 tracks.
(e) for Driver Side:

1. Connect the airbag connector.
(2) Connect the buckle switch connector.
B138555
(f) for Front Passenger Side:

(3) Connect the occupant detection ECU
connector.
B138557
2. INSTALL FRONT SEAT HEADREST ASSEMBLY

(a) Push in the lock button of the front seat headrest
support and install the front seat headrest.
TERMINAL
Lock Button
Airbag)
B138314E01 (See page RS-31)
SE
SE22 SEAT FRONT SEAT ASSEMBLY (for Hatchback)
FRONT SEAT ASSEMBLY (for Hatchback)

SEAT
BODY
COMPONENTS
for Driver Side:
FRONT SEAT HEADREST

ASSEMBLY
FRONT SEAT
ASSEMBLY
37 (375, 27)
x4
SE BUCKLE SWITCH
CONNECTOR
BUCKLE SWITCH
CONNECTOR
AIRBAG
CONNECTOR
B117721E02
SEAT FRONT SEAT ASSEMBLY (for Hatchback) SE23

FRONT SEAT HEADREST
ASSEMBLY
FRONT SEAT
ASSEMBLY
37 (375, 27)
x4
OCCUPANT
CLASSIFICATION
ECU CONNECTOR
BUCKLE SWITCH
CONNECTOR
SE
BUCKLE SWITCH
CONNECTOR
AIRBAG
CONNECTOR
OCCUPANT CLASSIFICATION
ECU CONNECTOR
B117720E02
for Driver Side: FRONT SEAT HEADREST

SUPPORT
FRONT SEATBACK
COVER PAD
FRONT SEAT CUSHION x3

COVER PAD
for Clip Type: for J Hook Type:
FRONT SEAT CUSHION

SHIELD RH x2
SE 42 (430, 31)
RECLINING ADJUSTER
RELEASE HANDLE
FRONT SEAT INNER
BELT ASSEMBLY
N*m (kgf*cm, ft*lbf) : Specified torque FRONT SEAT CUSHION

SHIELD LH
Non-reusable part
B114726E02
for Driver Side:

RECLINING ADJUSTER
OUTSIDE COVER RH

RECLINING ADJUSTER
INSIDE COVER RH
FRONT SEAT SIDE

AIRBAG ASSEMBLY
5.5 (55, 49 in.*lbf)
x2
FRONT SEAT ADJUSTER

FRAME ASSEMBLY
FRONT SEAT
CUSHION LOWER
SHIELD RH
SE
SEAT POSITION
SENSOR RECLINING ADJUSTER
INSIDE COVER LH
8.0 (80, 71 in.*lbf)
SEAT POSITION
SENSOR PROTECTOR
RECLINING ADJUSTER
OUTSIDE COVER LH

FRONT SEAT CUSHION
LOWER SHIELD LH
Non-reusable part
B114727E03
for Walk In Seat Type:

FRONT SEAT HEADREST
RECLINING REMOTE SUPPORT
CONTROL LEVER BEZEL
RECLINING REMOTE
CONTROL LEVER
FRONT SEATBACK
COVER PAD
FRONT SEAT CUSHION x3

COVER PAD
x2
FRONT SEAT CUSHION
SHIELD RH
RECLINING ADJUSTER
RELEASE HANDLE
SE
FRONT SEAT CUSHION

SHIELD LH

FRONT SEAT INNER
BELT ASSEMBLY 42 (430, 31)
Non-reusable part
B114728E02
for Front Passenger Side: RECLINING ADJUSTER

OUTSIDE COVER RH

RECLINING ADJUSTER
INSIDE COVER RH
FRONT SEAT SIDE
AIRBAG ASSEMBLY
5.5 (55, 49 in.*lbf)

x2
FRONT SEAT ADJUSTER
FRAME ASSEMBLY
FRONT SEAT CUSHION
LOWER SHIELD RH
SE
OCCUPANT
CLASSIFICATION
ECU
FRONT SEAT CUSHION
LOWER SHIELD LH
RECLINING ADJUSTER
RECLINING ADJUSTER OUTSIDE COVER LH
INSIDE COVER LH
FRONT SEAT WIRE
B114729E02
REMOVAL
CAUTION:
NOTICE:
the front seat.
HINT:
TERMINAL
CAUTION:
Seat Side Airbag).
2. REMOVE FRONT SEAT HEADREST ASSEMBLY
(a) Push in the lock buttons of the front seat headrest
support and remove the front seat headrest.
Lock Button
B117722E01
3. REMOVE FRONT SEAT ASSEMBLY

SE (a) for Driver Side:
connector.
Slider
B114688E01
(b) for Front Passenger Seat:

connector.
(3) Disconnect the occupant classification ECU
connector.
Slider
B114690E01
(c) Using "Torx" socket wrench E10, remove the 4 bolts

and the front seat.
B114689
SE
DISASSEMBLY
CAUTION:
HINT:
1. REMOVE RECLINING ADJUSTER RELEASE
HANDLE
Protective Tape
B114696E01
2. REMOVE FRONT SEAT CUSHION SHIELD LH

protective tape, disengage the 2 claws and clip, and
remove the front seat cushion shield.
(See page SB-39)
SE
B114697
4. REMOVE FRONT SEAT CUSHION SHIELD RH

protective tape, disengage the claw and clip, and
remove the front seat cushion shield.
B114698
5. REMOVE FRONT SEAT CUSHION COVER PAD

(a) Remove the front seatback cover band.
B114699
(b) for Clip Type:

(1) Using a clip remover, remove the 2 clips.
for Clip Type: for J Hook Type: (c) for J Hook Type:
(1) Disengage the 2 hooks.
(d) w/ Front Seat Side Airbag:
(1) Remove the hook tape from the front seat
cushion cover pad fixing cover.
SE
B114700E01
(e) Disengage the 2 claws and 9 hooks, and remove

the front seat cushion cover pad.
B114702
6. REMOVE FRONT SEAT HEADREST SUPPORT

(a) Remove the 3 hog rings shown in the illustration.
B114703
SE (b) Disengage the 2 claws and remove the front seat

headrest support.
HINT:
B114704
7. REMOVE RECLINING REMOTE CONTROL LEVER

(for Walk in Seat Type)
Protective Tape
B121714E01
8. REMOVE RECLINING REMOTE CONTROL LEVER

BEZEL (for Walk in Seat Type)
(a) Disengage the 5 claws and remove the reclining
remote control lever bezel.
B121715
9. REMOVE FRONT SEATBACK COVER PAD

(a) Remove the front seatback cover pad.
B114705
10. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY (w/

Front Seat Side Airbag)
(a) Remove the airbag connector and the 3 clamps.
B114706
(b) Using a clip remover, remove the 2 clamps. SE
B114707
(c) Remove the 2 nuts and the front seat side airbag.
B114708
11. REMOVE RECLINING ADJUSTER INSIDE COVER LH

HINT:
Use the same procedure as for the LH side.
B114710

LH
(a) Remove the screw and the reclining adjuster
outside cover.
RH
HINT:
B114709

LH
(a) Disengage the 2 claws and remove the front seat
B127732
SE 16. REMOVE FRONT SEAT CUSHION LOWER SHIELD

RH
(b) Disengage the claw and remove the front seat
B127731
17. REMOVE SEAT POSITION SENSOR (for Driver Side)

(a) Disengage the pin and remove the seat position
sensor protector.
B114730
(b) Using "Torx" socket wrench T30, remove the bolt

and the seat position sensor.
B114732
18. REMOVE FRONT SEAT WIRE (for Front Passenger

Side)
(a) Disconnect the 5 connectors.
(b) Remove the 2 clamps and the front seat wire.
B114734
19. REMOVE OCCUPANT CLASSIFICATION ECU (for

Front Passenger Side)
(a) Disengage the claw and remove the occupant
classification ECU.
B114735
SE
REASSEMBLY
CAUTION:
HINT:
1. INSTALL SEAT POSITION SENSOR (for Driver Side)
(a) Provisionally install the seat position sensor.
NOTICE:
If the seat position sensor has been dropped,
or there are any cracks, dents or other
defects in the case, bracket or connector,
replace the seat position sensor with a new
one.
When installing the seat position sensor,
make sure that the SRS wiring does not
interfere with other parts and is not pinched
Sensor
between other parts.
(b) Install a 1 mm (0.04 in.) feeler gauge between the
seat rail and seat position sensor, as shown in the
illustration.
HINT:
Make sure that the clearance between the seat
position sensor and seat rail is within 0.6 to 2 mm
(0.023 to 0.079 in.).
Seat Rail Feeler Gauge
(c) Push the top of the seat position sensor toward the
B114733E01 seat rail.
(d) While holding the seat position sensor, tighten the
seat position sensor using "Torx" socket wrench
SE T30.
(e) Engage the pin and install a new seat position

sensor protector.
B114731E01
NOTICE:
Do not damage portion A, shown in the
illustration, when installing the seat position
sensor protector.
2. INSTALL OCCUPANT CLASSIFICATION ECU (for
Front Passenger Side)
(a) Engage the claw and install the occupant
classification ECU.
SE
B114735
3. INSTALL FRONT SEAT WIRE (for Front Passenger

Side)
(a) Install the front seat wire with the 2 clamps.
(b) Connect the 5 connectors.
B114734
4. INSTALL FRONT SEAT CUSHION LOWER SHIELD LH

(a) Engage the 2 claws and install the front seat
B127732
5. INSTALL FRONT SEAT CUSHION LOWER SHIELD

RH
(a) Engage the claw and install the front seat cushion
lower shield.
B127731

LH
(a) Install the reclining adjuster outside cover with the
screw.
RH
HINT:
B114709
SE 8. INSTALL RECLINING ADJUSTER INSIDE COVER LH

inside cover.
9. INSTALL RECLINING ADJUSTER INSIDE COVER RH
HINT:
B114710
10. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY (w/

Front Seat Side Airbag)
(a) Install the front seat side airbag with the 2 nuts.
B114708
(b) Install the 2 clamps.
B114707
(c) Install the 3 clamps and the airbag connector.
B114706
11. INSTALL FRONT SEATBACK COVER PAD

(a) Install the front seatback cover pad.
NOTICE:
The fabring for fixing the airbag must mot be
wrinkled when installing the front seatback
cover pad (w/ Front Seat Side Airbag).
B114713
(b) Using hog ring pliers, install 3 new hog rings as SE

New Hog Ring
Hog Ring Pliers

B114714E01
12. INSTALL FRONT SEAT HEADREST SUPPORT

HINT:
Protruding Use the same procedure for both sides.
(a) Align the protruding portion of the front seat
headrest support with the installation groove of the
front seat back frame.
(b) Engage the 2 claws and install the front seat
headrest support.
B114715E02
13. INSTALL RECLINING REMOTE CONTROL LEVER

BEZEL (for Walk in Seat Type)
(a) Engage the 5 claws and install the reclining remote
control lever bezel.
B121715
14. INSTALL RECLINING REMOTE CONTROL LEVER

(for Walk in Seat Type)
release handle.
SE
B121733
15. INSTALL FRONT SEAT CUSHION COVER PAD

(a) Engage the 2 claws and 9 hooks, and install the
front seat cushion cover pad.
B114702
(b) w/ Front Seat Side Airbag:

(1) Fix the front seat side airbag wire harness with
for Clip Type: for J Hook Type: the front seat cushion cover pad fixing cover.
(c) for Clip Type:
(1) Install the 2 clips.
(d) for J Hook Type:
(1) Engage the 2 hooks.
SE
B114700E01
(e) Install the front seatback cover band.
B114699
16. INSTALL FRONT SEAT CUSHION SHIELD RH

(a) Engage the claw and the clip and install the front
seat cushion shield.
17. INSTALL FRONT SEAT INNER BELT ASSEMBLY (See
page SB-41)
B114698
18. INSTALL FRONT SEAT CUSHION SHIELD LH

(a) Engage the 2 claws and the clip and install the front
seat cushion shield.
SE
B114697
19. INSTALL RECLINING ADJUSTER RELEASE HANDLE

release handle.
B114716
INSTALLATION
CAUTION:
NOTICE:
front seat.
HINT:
same procedure for both front passenger and driver sides,
unless otherwise specified.
1. INSTALL FRONT SEAT ASSEMBLY
1 NOTICE:
Follow the procedure described below in order to
prevent the seat tracks from locking separately.
(a) Insert the 2 location pins through the 2 body holes,
place the front seat in the most forward position and
make sure that the inner and outer seat tracks are
locked securely.
(b) Using "Torx" socket wrench E10, install bolt 1 and
then bolt 2 onto the rear side.
2 Torque: 37 N*m (375 kgf*cm, 27 ft.*lbf)
3 (c) Move the front seat to the most rearward position,
and then make sure that the inner and outer seat
4 tracks are securely locked.
(d) Using "Torx" socket wrench E10, install bolt 3 and
B114717E01
then bolt 4 onto the rear side.
(e) Make sure that the inner and outer seat tracks lock
simultaneously after the seat is moved.
HINT:
SE
If the inner and outer seat tracks do not lock
simultaneously, adjust the seat tracks by loosening
the bolts.
(f) for Driver Side:
B114718
(g) for Front Passenger Side:

(2) Connect the occupant classification ECU
connector.
B114720
2. INSTALL FRONT SEAT HEADREST ASSEMBLY

(a) Push in the 2 lock buttons of the front seat headrest
supports and install the 2 front seat headrests.
TERMINAL
Lock Button 4. INSPECT SRS WARNING LIGHT (w/ Front Seat Side
Airbag)
B117722E01 (See page RS-31)
SE
SE44 SEAT REAR SEAT ASSEMBLY (for Sedan 60/40 Split Seat Type LH Side)
REAR SEAT ASSEMBLY (for Sedan 60/40 Split Seat Type LH

SEAT
BODY
Side)
COMPONENTS
REAR SEAT OUTER

BELT ASSEMBLY
37 (375, 27)
REAR SEATBACK
ASSEMBLY
x2
37 (375, 27)
SE
REAR SEAT INNER

BELT ASSEMBLY

PAD SUB-ASSEMBLY
B134921E01
SEAT REAR SEAT ASSEMBLY (for Sedan 60/40 Split Seat Type LH Side) SE45
REAR SEAT HEADREST

REAR SEATBACK STOP ASSEMBLY
BUTTON GROMMET
REAR SEAT HEADREST

SUPPORT
19.1 (195, 14) x2
x2
REAR SEAT SHOULDER
BELT GUIDE
REAR SEATBACK
LOCK ASSEMBLY
REAR SEATBACK COVER

PAD SUB-ASSEMBLY
REAR SEATBACK LOCK
CONTROL BEZEL
SE
x6
REAR SEATBACK
x8 FRAME SUB-ASSEMBLY
HOG RING
Non-reusable part
B138548E01
REMOVAL
ASSEMBLY
(a) Hold the front edge of the rear seat cushion cover
pad and lift it up, as shown in the illustration, to
disengage the 2 hooks.
NOTICE:
Hold the area around the hooks so as to avoid
deforming the rear seat cushion frame.
(b) Pass the rear seat inner belt through the slit in the
rear seat cushion cover pad, disengage the hook
between the rear seat cushion cover pad and the
rear seatback, and remove the rear seat cushion
cover pad.
B134922
2. REMOVE REAR SEATBACK ASSEMBLY

(a) Remove the rear seat outer belt from the rear seat
shoulder belt guide.
(b) Pull the rear seatback lock release button and tilt
the rear seatback forward.
B134924
(c) Using a clip remover, remove the 2 clips and the

rear seatback cover.
SE
B134925
(d) Remove the 2 bolts, the 2 hooks and the rear

seatback.
B134926
SE
DISASSEMBLY
CAUTION:
Wear protective gloves. Sharp surfaces on the rear
seatback frame could cause injuries to your hands.
1. REMOVE REAR SEAT HEADREST ASSEMBLY
(a) Push the lock button of the rear seat headrest
support and remove the rear seat headrest.
Lock Button
B134928E01
2. REMOVE REAR SEAT SHOULDER BELT GUIDE

(a) Remove the 2 screws and the rear seat shoulder
belt guide.
B134929
3. REMOVE REAR SEATBACK LOCK RELEASE

BUTTON
(a) Remove the rear seatback lock release button.
SE
B134931
4. REMOVE REAR SEATBACK LOCK CONTROL BEZEL

(a) Disengage the 2 claws and remove the rear
seatback lock control bezel.
B134932
5. REMOVE REAR SEAT HEADREST SUPPORT

(a) Using a clip remover, remove the 6 clips and open
the rear seatback cover.
B134933
B134934
(c) Disengage the 2 claws and remove the rear seat

SE
headrest support.
HINT:
B134936
6. REMOVE REAR SEATBACK STOP BUTTON

GROMMET
seatback stop button grommet.
B134938
7. REMOVE REAR SEATBACK FRAME SUB-

ASSEMBLY
(a) Remove the rear seatback frame.
B134939
8. REMOVE REAR SEATBACK LOCK ASSEMBLY

(a) Remove the 2 bolts and the rear seatback lock.
B134940
SE
REASSEMBLY
CAUTION:
1. INSTALL REAR SEATBACK LOCK ASSEMBLY
(a) Install the rear seatback lock with the 2 bolts.
Torque: 19.1 N*m (195 kgf*cm, 14 ft.*lbf)
B134940
2. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY

(a) Install the rear seatback frame.
B134939
SE
(b) Using hog ring pliers, install 8 new hog rings as

New Hog Ring
Hog Ring Pliers

B134935E01
(c) Install the rear seatback cover with the 6 clips.
SE
B134933
3. INSTALL REAR SEATBACK STOP BUTTON

GROMMET
(a) Engage the 2 claws and install the rear seatback
stop button grommet.
B134938
4. INSTALL REAR SEAT HEADREST SUPPORT

HINT:
(a) Align the protruding portion of the rear seat headrest
support with the installation groove of the rear
seatback frame.
Protruding
(b) Engage the 2 claws and install the rear seat
headrest support.
B134937E01
5. INSTALL REAR SEATBACK LOCK CONTROL BEZEL

lock control bezel.
B134932
6. INSTALL REAR SEATBACK LOCK RELEASE

BUTTON
(a) Install the rear seatback lock release button.
SE
B134931
7. INSTALL REAR SEAT SHOULDER BELT GUIDE

(a) Insert the pin into the rear seatback frame hole and
install the rear seat shoulder belt guide with the 2
screws.
B134930
8. INSTALL REAR SEAT HEADREST ASSEMBLY

support and install the rear seat headrest.
Lock Button
B134928E01
INSTALLATION
1. INSTALL REAR SEATBACK ASSEMBLY
(a) Insert the 2 hooks into the rear seatback frame hole
and install the rear seatback, tightening the 2 bolts
in the sequence shown in the illustration.
2 1
B134926E01
(b) Install the rear seatback cover with the 2 clips.

(c) Pull up the rear seatback.
SE
B134925
(d) Install the rear seat outer belt into the rear seat
B134924

ASSEMBLY
(a) Pass the rear seat inner belt through the rear seat
cushion cover pad slit.
(b) Engage the 3 hooks and install the rear seat
cushion cover pad.
NOTICE:
Make sure that the 2 rear seat cushion lock
hooks and the rear seat cushion frame are
securely engaged.
B134923
SE
SE54 SEAT REAR SEAT ASSEMBLY (for Sedan 60/40 Split Seat Type RH Side)
REAR SEAT ASSEMBLY (for Sedan 60/40 Split Seat Type RH

SEAT
BODY
Side)
COMPONENTS
REAR SEAT OUTER

BELT ASSEMBLY
REAR CENTER SEAT
OUTER BELT ASSEMBLY
37 (375, 27)
REAR SEATBACK
ASSEMBLY
x2
37 (375, 27)
SE
PAD SUB-ASSEMBLY
REAR SEAT INNER

BELT ASSEMBLY
B134942E02
SEAT REAR SEAT ASSEMBLY (for Sedan 60/40 Split Seat Type RH Side) SE55
REAR CENTER SEAT

HEADREST ASSEMBLY
REAR SEAT HEADREST

ASSEMBLY REAR SEATBACK LOCK
RELEASE BUTTON
x2 x2
REAR CENTER SEAT
SHOULDER BELT GUIDE REAR CENTER SEAT
SHOULDER BELT GUIDE
REAR SEATBACK LOCK

CONTROL BEZEL
x7 33 (335, 24)
SE
21 (215, 16)
CUP HOLDER
ASSEMBLY
21 (215, 16)
REAR SEAT CENTER
ARMREST ASSEMBLY
REAR SEAT CENTER

ARMREST HINGE
REAR SEAT CENTER
ARMREST HINGE COVER

B134946E02
REAR SEATBACK STOP REAR SEAT HEADREST

BUTTON GROMMET SUPPORT
19.1 (195, 14)

x2
REAR SEAT HEADREST
REAR SEATBACK SUPPORT
LOCK ASSEMBLY
REAR SEATBACK COVER

PAD SUB-ASSEMBLY
REAR SEATBACK
SE FRAME SUB-ASSEMBLY
x9
Non-reusable part
B138549E01
REMOVAL
ASSEMBLY (See page SE-46)
(a) Remove the rear seat outer belt from the rear seat
(b) Remove the rear center seat outer belt from the rear
center seat shoulder belt guide.
(c) Pull the rear seatback lock release button and tilt
the rear seatback forward.
B134943
(d) Using a clip remover, remove the 2 clips and the

rear seatback cover.
B134944
(e) Remove the 2 bolts, the 2 hooks and the rear

seatback. SE
B134945
DISASSEMBLY
CAUTION:
Lock Button
B134947E01
2. REMOVE REAR CENTER SEAT HEADREST

ASSEMBLY
Lock Button
B134948E01
3. REMOVE REAR SEAT SHOULDER BELT GUIDE

belt guide.
SE
B134949
4. REMOVE REAR SEATBACK LOCK RELEASE

BUTTON
(a) Remove the rear seatback lock release button.
B134953
5. REMOVE REAR CENTER SEAT SHOULDER BELT

GUIDE
(a) Remove the 2 screws and the rear center seat
B134951
6. REMOVE REAR SEATBACK LOCK CONTROL BEZEL

seatback lock control bezel.
B134954
7. REMOVE REAR SEAT CENTER ARMREST

ASSEMBLY
(a) Using a clip remover, remove the 7 clips and open
the rear seatback cover.
SE
B134955
(b) Remove the 2 nuts, the 2 wave washers and the

rear seat center armrest.
B134956
8. REMOVE REAR SEAT CENTER ARMREST HINGE

COVER
armrest hinge cover.
B134957
9. REMOVE REAR SEAT CENTER ARMREST HINGE

(a) Remove the 2 bolts, the 2 spacers and the rear seat
armrest hinge.
B134958
10. REMOVE CUP HOLDER ASSEMBLY

(a) Disengage the 4 claws and remove the cup holder.
B134959
SE 11. REMOVE REAR SEAT HEADREST SUPPORT

B134960
(b) Disengage the 2 claws and remove the rear seat

headrest support.
HINT:
Use the same procedure to remove all the rear seat
headrest supports.
B134962
12. REMOVE REAR SEATBACK FRAME SUB-

ASSEMBLY
(a) Remove the rear seatback frame.
B134964
13. REMOVE REAR SEATBACK LOCK ASSEMBLY

(a) Remove the 2 bolts and the rear seatback lock.
SE
B134965
REASSEMBLY
CAUTION:
1. INSTALL REAR SEATBACK LOCK ASSEMBLY
(a) Install the rear seatback lock with the 2 bolts.
Torque: 19.1 N*m (195 kgf*cm, 14 ft.*lbf)
B134965
2. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY

(a) Install the rear seatback frame.
B134964
SE
(b) Using hog ring pliers, install 9 new hog rings as

New Hog Ring
Hog Ring Pliers

B134961E01

HINT:
Use the same procedure to install all the rear seat
headrest supports.
Protruding
support with the installation groove of the rear SE
seatback frame.
headrest support.
B134963E01
4. INSTALL CUP HOLDER ASSEMBLY

(a) Engage the 4 claws and install the rear seat cup
holder.
B134959
5. INSTALL REAR SEAT CENTER ARMREST HINGE

(a) Install the rear seat armrest hinge with the 2 bolts,
the 2 spacers and the 2 spacers.
B134958
6. INSTALL REAR SEAT CENTER ARMREST HINGE

COVER
(a) Engage the 3 claws and install the rear seat center
armrest hinge cover.
B134957
7. INSTALL REAR SEAT CENTER ARMREST

ASSEMBLY
(a) Install the rear seat center armrest with the 2 nuts
and the 2 wave washers.
B134956
SE (b) Install the rear seatback cover with the 7 clips.
B134955
8. INSTALL REAR SEATBACK LOCK CONTROL BEZEL

lock control bezel.
B134954
9. INSTALL REAR CENTER SEAT SHOULDER BELT

GUIDE
install the rear center seat shoulder belt guide with
the 2 screws.
B134952
10. INSTALL REAR SEATBACK LOCK RELEASE

BUTTON
(a) Install the rear seatback lock release button.
B134953
11. INSTALL REAR SEAT SHOULDER BELT GUIDE SE

install the rear seat shoulder belt guide with the 2
screws.
B134950
12. INSTALL REAR CENTER SEAT HEADREST

ASSEMBLY
Lock Button
B134948E01

Lock Button
B134947E01
INSTALLATION
(a) Insert the 2 hooks into the rear seatback frame hole
and install the rear seatback, tightening the 2 bolts
in the sequence shown in the illustration.
2
1
B134945E01
(b) Install the rear seatback cover with the 2 clips.

(c) Pull up the rear seatback.
SE
B134944
(d) Install the rear seat outer belt into the rear seat
(e) Install the rear center seat outer belt into the rear
ASSEMBLY (See page SE-53)
B134943
SE66 SEAT REAR SEAT ASSEMBLY (for Hatchback 60/40 Split Seat Type LH Side)
REAR SEAT ASSEMBLY (for Hatchback 60/40 Split Seat

SEAT
BODY
Type LH Side)
COMPONENTS
PACKAGE TRAY TRIM

PANEL ASSEMBLY
DECK BOARD
SUB-ASSEMBLY
DECK FLOOR BOX
SE
NO. 1 REAR SEAT

LEG COVER
NO. 2 REAR SEAT

LEG COVER
37 (375, 27) REAR SEAT ASSEMBLY

x7
B138682E01
SEAT REAR SEAT ASSEMBLY (for Hatchback 60/40 Split Seat Type LH Side) SE67
x7

PAD SUB-ASSEMBLY
42 (430, 31)
REAR CENTER SEAT INNER

BELT ASSEMBLY RH
42 (430, 31)
REAR SEAT INNER

BELT ASSEMBLY
42 (430, 31)
REAR CENTER SEAT INNER

SE
BELT ASSEMBLY LH
20 (205, 15)
x2
21 (215, 16)
REAR SEAT CUSHION
FRAME SUB-ASSEMBLY
REAR SEAT SIDE

HINGE COVER
Non-reusable part
B127716E02
REAR CENTER SEAT

HEADREST ASSEMBLY
REAR SEAT HEADREST
ASSEMBLY
REAR SEAT HEADREST

SUPPORT REAR SEAT LOCK
STRIKER COVER
x2
REAR SEAT LOCK CONTROL

LEVER SUB-ASSEMBLY
REAR SEATBACK COVER

PAD SUB-ASSEMBLY
x7
REAR SEAT BELT HOOK
SE 5.0 (50, 44 in.*lbf)
Non-reusable part
B127717E02
x6
x2
REAR SEAT UNDER

TRAY COVER
REAR SEAT RECLINING
OUTSIDE COVER RH
RECLINING ADJUSTER
INSIDE COVER RH
33 (335, 24)
x3 REAR SEATBACK
FRAME SUB-ASSEMBLY
x4
x2
REAR SEAT SLIDE
CONTROL CABLE RECLINING ADJUSTER
33 (335, 24) INSIDE COVER LH SE
REAR SEAT
RECLINING
INSIDE COVER
REAR SEAT TRACK

ASSEMBLY RH
REAR SEAT TRACK

ASSEMBLY LH
REAR SEAT RECLINING
CONTROL CABLE REAR SEAT RECLINING
OUTSIDE COVER LH
B114687E02
REMOVAL
NOTICE:
the rear seat.
(See page IR-48)
IR-48)
(a) Release the 2 knobs and remove the deck floor box.
B106373
4. REMOVE NO. 1 REAR SEAT LEG COVER

(a) Disengage the 4 claws in the sequence shown in
the illustration and remove the No. 1 rear seat leg
cover.
SE 1
2
B126919E01

cover.
1
2
B126921E01
6. REMOVE REAR SEAT ASSEMBLY

(a) Using "Torx" socket wrench E10, remove the 3 bolts
and pull up the rear seat cushion.
B114740
(b) Using "Torx" socket wrench E10, remove the 4 bolts

and the rear seat.
B117760
SE
DISASSEMBLY
CAUTION:
ASSEMBLY RH
(a) Remove the bolt and the rear center seat inner belt.
B114654

ASSEMBLY LH
(a) Remove the belt from the band.
(b) Remove the bolt and the rear center seat inner belt.
Band
B114651E01

(b) Remove the bolt and the rear seat inner belt.
SE
Band
B114647E01
4. REMOVE REAR SEAT SIDE HINGE COVER

side hinge cover.
B117761
5. REMOVE REAR SEAT CUSHION ASSEMBLY

(a) Using "Torx" socket wrench T45, remove the bolt
and the spacer.
(b) Remove the 2 nuts and rear seat cushion.
B114741

ASSEMBLY
(b) Disengage the 7 hooks and remove the rear seat
cushion cover pad.
B114742

SE
(a) Push in the lock button of the rear seat headrest
Lock Button
B117762E01

ASSEMBLY
support and remove the rear center seat headrest.
Lock Button
B114744E01
9. REMOVE REAR SEAT LOCK STRIKER COVER

the rear seat lock striker cover.
Protective Tape
B117763E01
10. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-

ASSEMBLY
(a) Remove the 2 screws.
(b) Disconnect the rear seat reclining control cable and
the rear seat slide control cable, and remove the
rear seat lock control lever.
B117764

(a) Remove the 2 rear seatback cover bands.
SE
B114745
B114746
(c) Unfasten the 2 zippers.

(d) Remove the bolt and the rear seat belt hook.
B127656
(e) Disengage the 2 claws and remove the rear seat

headrest support.
HINT:
headrest supports.
B114758
12. REMOVE REAR SEATBACK COVER PAD SUB-

ASSEMBLY
(a) Remove the rear seatback cover pad.
SE
B114750
13. REMOVE REAR SEAT UNDER TRAY COVER

(a) Using a clip remover, remove the 6 clips and the
rear seat under tray cover.
B114751
14. REMOVE REAR SEAT RECLINING OUTSIDE COVER

LH
(a) Remove the screw and the rear seat reclining
outside cover.
B117766

RH
(a) Remove the 2 screws and the rear seat reclining
outside cover.
B117765
16. REMOVE REAR SEAT RECLINING INSIDE COVER

inside cover.
B117767
SE 17. REMOVE RECLINING ADJUSTER INSIDE COVER LH

HINT:
B114752
19. REMOVE REAR SEAT RECLINING CONTROL CABLE

(a) Remove the rear seat reclining control cable.
B114753
20. REMOVE REAR SEAT SLIDE CONTROL CABLE

(a) Remove the rear seat slide control cable.
B114754
(b) Remove the 5 clamps.

SE
B114755
21. REMOVE REAR SEAT TRACK ASSEMBLY LH

(a) Remove the 2 nuts and the rear seat track.
B114757
22. REMOVE REAR SEAT TRACK ASSEMBLY RH

B114756
SE
REASSEMBLY
CAUTION:
1. INSTALL REAR SEAT TRACK ASSEMBLY LH
(a) Install the rear seat track with the 2 nuts.
B114757
2. INSTALL REAR SEAT TRACK ASSEMBLY RH

B114756
3. INSTALL REAR SEAT SLIDE CONTROL CABLE

(a) Install the 5 clamps.
SE
B114755
(b) Install the rear seat slide control cable as shown in

the illustration.
Red Tape
Red Tape
B127715E01
4. INSTALL REAR SEAT RECLINING CONTROL CABLE

Yellow Tape
(a) Install the rear seat reclining control cable as shown
in the illustration.
SE
Yellow Tape
B127714E01
5. INSTALL RECLINING ADJUSTER INSIDE COVER LH

inside cover.
6. INSTALL RECLINING ADJUSTER INSIDE COVER RH
HINT:
B114752
7. INSTALL REAR SEAT RECLINING INSIDE COVER

reclining inside cover.
B117767
8. INSTALL REAR SEAT RECLINING OUTSIDE COVER

LH
(a) Install the rear seat reclining outside cover with the
screw.
B117766
9. INSTALL REAR SEAT RECLINING OUTSIDE COVER SE

RH
2 screws.
B117765
10. INSTALL REAR SEAT UNDER TRAY COVER

(a) Install the rear seat under tray cover with the 6 clips.
B114751
11. INSTALL REAR SEATBACK COVER PAD SUB-

ASSEMBLY
(a) Install the rear seatback cover pad.
B114750
(b) Install the rear seat belt hook with the bolt.
(c) Fasten the 2 zippers.
B127656
(d) Using hog ring pliers, install 7 new hog rings.
SE
New Hog Ring
Hog Ring Pliers

B114747E02
(e) Install the 2 rear seatback bands.
B114745

HINT:
headrest supports.
Protruding
seatback frame.
headrest support.
B114749E02
13. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-

SE
ASSEMBLY
(a) Connect the rear seat reclining control cable and the
rear seat slide control cable, and install the rear seat
lock control lever.
(b) Tighten the 2 screws.
B117764
14. INSTALL REAR SEAT LOCK STRIKER COVER

(a) Engage the 2 claws and install the rear seat lock
striker cover.
B117768

ASSEMBLY
support and install the rear center seat headrest.
Lock Button
B114744E01

Lock Button
B117762E01

ASSEMBLY
(a) Engage the 7 hooks and install the rear seat
cushion cover pad.
SE
New Hog Ring
Hog Ring Pliers

B114743E01
18. INSTALL REAR SEAT CUSHION ASSEMBLY

(a) Install the rear seat cushion with the 2 nuts.
(b) Install the bolt into the spacer.
(c) Using "Torx" socket wrench T45, tighten the bolt.
B114741
19. INSTALL REAR SEAT SIDE HINGE COVER

(a) Engage the 4 claws and install the rear seat side
hinge cover.
B117761

(a) Install the rear seat inner belt with the bolt.
NOTICE:
Do not place the anchor plate over the convex
area of the rear seatback frame. SE
(b) Install the belt into the band.
Convex
Band
B114648E01

ASSEMBLY LH
(a) Install the rear center seat inner belt with the bolt.
NOTICE:
areas of the rear seatback frame.
Band
Convex
B114652E01

ASSEMBLY RH
(a) Install the rear center seat inner belt with the bolt.
NOTICE:
area of the rear seatback frame.
Convex
B114655E01
SE
INSTALLATION
NOTICE:
rear seat.
1. INSTALL REAR SEAT ASSEMBLY
(a) Insert the 2 locating pins through the 2 body holes
3
and install the rear seat.
(b) Using "Torx" socket wrench E10, install the 4 bolts in
the sequence shown in the illustration.
1 2
B126922E01
(c) Install the rear seat cushion.

(d) Using "Torx" socket wrench E10, install the 3 bolts in
2 1
B114740E01
2. INSTALL NO. 2 REAR SEAT LEG COVER SE

(a) Engage the 3 claws and install the No. 2 rear seat
leg cover.
B114739
3. INSTALL NO. 1 REAR SEAT LEG COVER

leg cover.
B114738

(a) Install the deck floor box and lock the 2 knobs.
IR-83)
(See page IR-83)
B106445
SE
SE86 SEAT REAR SEAT ASSEMBLY (for Hatchback 60/40 Split Seat Type RH Side)
REAR SEAT ASSEMBLY (for Hatchback 60/40 Split Seat

SEAT
BODY
Type RH Side)
COMPONENTS
PACKAGE TRAY TRIM

PANEL ASSEMBLY
DECK BOARD
SUB-ASSEMBLY
DECK FLOOR BOX
SE
REAR SEAT ASSEMBLY

NO. 1 REAR SEAT
LEG COVER
37 (375, 27)
x6
B138683E01
SEAT REAR SEAT ASSEMBLY (for Hatchback 60/40 Split Seat Type RH Side) SE87
REAR SEAT LOCK

STRIKER COVER
REAR SEAT HEADREST
x2
ASSEMBLY
REAR SEAT LOCK CONTROL

LEVER SUB-ASSEMBLY
REAR SEAT HEADREST

SUPPORT
REAR SEATBACK COVER

PAD SUB-ASSEMBLY
PAD SUB-ASSEMBLY
x5
x4
REAR SEAT SIDE

HINGE COVER
SE
21 (215, 16)
42 (430, 31)
REAR SEAT INNER

BELT ASSEMBLY
REAR SEAT
CUSHION FRAME
SUB-ASSEMBLY
21 (215, 16)
REAR SEAT SIDE

HINGE COVER
Non-reusable part
B127713E02
REAR SEAT RECLINING

OUTSIDE COVER RH
x4
REAR SEAT UNDER

TRAY COVER
REAR SEAT RECLINING

INSIDE COVER RH
REAR SEATBACK FRAME

SUB-ASSEMBLY
33 (335, 24)
x2
x2
RECLINING ADJUSTER
INSIDE COVER
33 (335, 24)
x2
REAR SEAT RECLINING

REAR SEAT SLIDE INSIDE COVER LH
SE CONTROL CABLE
REAR SEAT RECLINING

OUTSIDE COVER LH
REAR SEAT TRACK

ASSEMBLY RH
REAR SEAT RECLINING
CONTROL CABLE REAR SEAT TRACK
ASSEMBLY LH
B114658E02
REMOVAL
NOTICE:
the rear seat.
(See page IR-48)
IR-48)
3. REMOVE DECK FLOOR BOX (See page IR-48)
cover.
B126923E01
5. REMOVE REAR SEAT ASSEMBLY

and pull up the rear seat cushion.
SE
B114660
(b) Using "Torx" socket wrench E10, remove the 4 bolts

and the rear seat.
B119885
DISASSEMBLY
CAUTION:
(b) Remove the bolt and the rear seat inner belt.
Band
B114643E01
2. REMOVE REAR SEAT SIDE HINGE COVER

HINT:
side hinge cover.
B119886
3. REMOVE REAR SEAT CUSHION ASSEMBLY

(a) Using "Torx" socket wrench T45, remove the 2 bolts,
2 spacers and the rear seat cushion.
SE
B119887

ASSEMBLY
(b) Disengage the 7 hooks and remove the rear seat
cushion cover pad.
B119888

Lock Button
B108395E01

the rear seat back lock striker cover.
SE
Protective Tape
B119889E01

ASSEMBLY
the rear seat slide control cable, and remove the
rear seat lock control lever.
B126920

(a) Remove the rear seatback cover band.
B119890
B119891
(c) Unfasten the 2 zippers.
SE
B119892
(d) Disengage the 2 claws and remove the rear seat

headrest support.
HINT:
B114669

ASSEMBLY
B114670
10. REMOVE REAR SEAT UNDER TRAY COVER

(a) Using a clip remover, remove the 4 clips and the
rear seat under tray cover.
B114671

LH
outside cover.
B108405
12. REMOVE REAR SEAT RECLINING OUTSIDE COVER SE

RH
outside cover.
B108404
13. REMOVE REAR SEAT RECLINING INSIDE COVER LH

inside cover.
B114672
14. REMOVE REAR SEAT RECLINING INSIDE COVER

RH
inside cover.
B114673
15. REMOVE RECLINING ADJUSTER INSIDE COVER

B114674
16. REMOVE REAR SEAT RECLINING CONTROL CABLE

SE
B114675
17. REMOVE REAR SEAT SLIDE CONTROL CABLE

(a) Remove the rear seat slide control cable.
B114676
B114677
18. REMOVE REAR SEAT TRACK ASSEMBLY LH

B114679
19. REMOVE REAR SEAT TRACK ASSEMBLY RH

B114678
SE
REASSEMBLY
CAUTION:
1. INSTALL REAR SEAT TRACK ASSEMBLY LH
B114679
2. INSTALL REAR SEAT TRACK ASSEMBLY RH

B114678
3. INSTALL REAR SEAT SLIDE CONTROL CABLE

SE
B114677
(b) Install the rear seat slide control cable as shown in

the illustration.
Blue Tape
Blue Tape
B127712E01

(a) Install the rear seat reclining control cable as shown
Green Tape in the illustration.
SE
B127711E01
5. INSTALL RECLINING ADJUSTER INSIDE COVER

inside cover.
B114674
6. INSTALL REAR SEAT RECLINING INSIDE COVER LH

B114672
7. INSTALL REAR SEAT RECLINING INSIDE COVER RH

B114673
SE 8. INSTALL REAR SEAT RECLINING OUTSIDE COVER

RH
screw.
B108404
9. INSTALL REAR SEAT RECLINING OUTSIDE COVER

LH
screw.
B108405
10. INSTALL REAR SEAT UNDER TRAY COVER

(a) Install the rear seat under tray cover with the 4 clips.
B114671
11. INSTALL REAR SEATBACK COVER PAD SUB-

ASSEMBLY
B114670
(b) Fasten the 2 zippers.
SE
B119892
(c) Using hog ring pliers, install 5 new hog rings.
New Hog Ring
Hog Ring Pliers

B114680E01
(d) Install the rear seat back band.
SE
B119890

HINT:
seatback frame.
headrest support.
Protruding
B114681E02

ASSEMBLY
(a) Connect the rear seat reclining control cable and the
rear seat slide control cable, and install the rear seat
lock control lever.
B126920

(a) Engage the 2 claws and install the rear seat lock
striker cover.
B114682

Lock Button
B108395E01
SE

ASSEMBLY
(a) Engage the 7 hooks and install the rear seat
cushion cover pad.
New Hog Ring
Hog Ring Pliers
B114683E01
17. INSTALL REAR SEAT CUSHION ASSEMBLY

(a) Install the 2 bolts into the 2 spacers.
(b) Using "Torx" socket wrench T45, install the rear seat
cushion with the 2 bolts and the 2 spacers.
SE
B119887
18. INSTALL REAR SEAT SIDE HINGE COVER

HINT:
(a) Engage the 4 claws and install the rear seat side
hinge cover.
B119886

(a) Install the rear seat inner belt with the bolt.
NOTICE:
areas of the rear seatback frame.
Convex
Band
B114644E01
SE
INSTALLATION
NOTICE:
rear seat.
1. INSTALL REAR SEAT ASSEMBLY
3 (a) Insert the 2 locating pins through the 2 body holes
and install the rear seat.
(b) Using "Torx" socket wrench E10, install the 4 bolts in
2
1
B114684E01
(c) Install the rear seat cushion.

(d) Using "Torx" socket wrench E10, install the 2 bolts in
1
2
B114660E01
SE 2. INSTALL NO. 1 REAR SEAT LEG COVER

leg cover.
3. INSTALL DECK FLOOR BOX (See page IR-83)
IR-83)
(See page IR-83)
B114659
SE104 SEAT REAR SEAT ASSEMBLY (for Fixed Seat Type)
REAR SEAT ASSEMBLY (for Fixed Seat Type)

SEAT
BODY
COMPONENTS
REAR CENTER SEAT

REAR SEAT OUTER OUTER BELT ASSEMBLY
BELT ASSEMBLY RH
REAR SEAT OUTER

BELT ASSEMBLY LH
7.9 (80, 70 in.*lbf)

x3
REAR SEATBACK
ASSEMBLY
SE
REAR SEAT INNER
BELT ASSEMBLY RH
REAR SEAT INNER

BELT ASSEMBLY LH
REAR SEAT CUSHION


B134979E04
SEAT REAR SEAT ASSEMBLY (for Fixed Seat Type) SE105
REAR CENTER SEAT

HEADREST ASSEMBLY
x2
REAR CENTER SEAT

SHOULDER BELT GUIDE
REAR SEAT HEADREST

ASSEMBLY
x2
REAR SEAT SHOULDER
BELT GUIDE RH
REAR SEAT HEADREST
ASSEMBLY
SE
x2
REAR SEAT SHOULDER
BELT GUIDE LH
B134980E02
REMOVAL
ASSEMBLY
disengage the 2 hooks.
NOTICE:
Hold the area around the hooks so as to avoid
deforming the rear seat cushion frame.
cover pad.
B138595

for RH Side: (a) Remove the rear seat outer belt from the rear seat
HINT:
(b) Remove the rear center seat outer belt from the rear
for LH Side:
SE
B138450E01
(c) Remove the 3 bolts.

(d) Disengage the 3 hooks and remove the rear
seatback.
B134981
DISASSEMBLY
HINT:
Lock Button support and remove the rear seat headrest.
B134982E01

ASSEMBLY
support and remove the rear center seat headrest.
Lock Button
B134983E01
3. REMOVE REAR SEAT SHOULDER BELT GUIDE RH

belt guide.
4. REMOVE REAR SEAT SHOULDER BELT GUIDE LH
HINT:
B134984
5. REMOVE REAR CENTER SEAT SHOULDER BELT SE

GUIDE
(a) Remove the 2 screws and the rear center seat
B134986
REASSEMBLY
1. INSTALL REAR CENTER SEAT SHOULDER BELT
GUIDE
(a) Insert the pin into the rear seatback hole and install
the rear center seat shoulder belt guide with the 2
screws.
B134987
2. INSTALL REAR SEAT SHOULDER BELT GUIDE RH

(a) Insert the pin into the rear seatback hole and install
the rear seat shoulder belt guide with the 2 screws.
3. INSTALL REAR SEAT SHOULDER BELT GUIDE LH
HINT:
B134985

ASSEMBLY
Lock Button
B134983E01

HINT:
Lock Button
B134982E01
SE INSTALLATION
(a) Engage the 3 hooks and install the rear seatback.
(b) Tighten the 3 bolts.
B134981
(c) Install the rear seat outer belt into the rear seat
for RH Side: shoulder belt guide.
HINT:
(d) Install the rear center seat outer belt into the rear
for LH Side:
B138450E01

ASSEMBLY
(a) Pass the rear seat inner belt through the rear seat
cushion cover pad slit.
cushion cover pad.
NOTICE:
Make sure that the 2 rear seat cushion lock
hooks and the rear seat cushion frame are
securely engaged.
SE
B138623
SE110 SEAT REAR SEAT ASSEMBLY (for Hold Down Seat Type)
REAR SEAT ASSEMBLY (for Hold Down Seat Type)

SEAT
BODY
COMPONENTS
PACKAGE TRAY TRIM

PANEL ASSEMBLY
DECK BOARD
SUB-ASSEMBLY
SE
DECK FLOOR BOX RH
DECK FLOOR BOX LH
B114273E01
SEAT REAR SEAT ASSEMBLY (for Hold Down Seat Type) SE111

PAD SUB-ASSEMBLY
REAR SEATBACK
SE
ASSEMBLY
REAR SEAT CUSHION

LOCK HOOK
x4 37 (375, 27)
B117738E02
REAR CENTER SEAT

HEADREST ASSEMBLY REAR SEAT LOCK
x2 STRIKER COVER
x2
REAR SEAT HEADREST REAR SEAT LOCK CONTROL

ASSEMBLY LEVER SUB-ASSEMBLY
REAR SEAT HEADREST

ASSEMBLY
REAR SEAT HEADREST

SUPPORT
REAR SEATBACK COVER

PAD SUB-ASSEMBLY
SE
REAR SEAT BELT HOOK
5.0 (50, 44 in.*lbf)
B117739E02
x2
REAR SEATBACK FRAME

SUB-ASSEMBLY
REAR SEAT RECLINING

CONTROL CABLE
42 (430, 31)
x4
RECLINING
ADJUSTER UPPER
INSIDE COVER RH
RECLINING
ADJUSTER UPPER
INSIDE COVER LH
SE
REAR SEAT RECLINING RECLINING
COVER RH ADJUSTER LOWER
INSIDE COVER RH
RECLINING
ADJUSTER LOWER
INSIDE COVER LH
REAR SEAT LEG

SUB-ASSEMBLY
REAR SEAT RECLINING
COVER LH
B127710E02
REMOVAL
NOTICE:
the rear seat.
(See page IR-48)
IR-48)
ASSEMBLY
disengage the 2 rear seat cushion lock hooks.
NOTICE:
Hold the area around the rear seat cushion
hooks so as to avoid deforming the rear seat
cushion frame.
cover pad.
B117740
6. REMOVE REAR SEAT CUSHION LOCK HOOK

(a) Disengage the 4 claws and remove the 2 rear seat
cushion lock hooks.
SE
B117741

and the rear seat back.
B117742
SE
DISASSEMBLY
CAUTION:
HINT:
Lock Button
B117744E01

ASSEMBLY
(a) Push in the lock button of the rear seat headrest and
remove the rear center seat headrest.
Lock Button
SE
B127657E01

the rear seat lock striker cover.
Protective Tape
B127658E01

ASSEMBLY
remove the rear seat lock control lever.
B127660

(a) Disengage the hook.
B117747
(b) Unfasten the 2 zippers.

(c) Remove the bolt and the rear seat belt hook.
B117748
(d) Disengage the 2 claws and remove the rear seat SE

headrest support.
HINT:
headrest supports.
B117749

ASSEMBLY
B117750
7. REMOVE REAR SEAT RECLINING COVER LH

(b) Using a clip remover, remove the clip.
(c) Disengage the 4 claws and remove the rear seat
reclining cover.
8. REMOVE REAR SEAT RECLINING COVER RH
HINT:
B117751
9. REMOVE RECLINING ADJUSTER UPPER INSIDE

COVER LH
adjuster upper inside cover.
10. REMOVE RECLINING ADJUSTER UPPER INSIDE
COVER RH
HINT:
B127661
11. REMOVE RECLINING ADJUSTER LOWER INSIDE

COVER LH
(a) Using a clip remover, remove the clip and the
reclining adjuster lower inside cover.
12. REMOVE RECLINING ADJUSTER LOWER INSIDE
COVER RH
HINT:
B117752
SE 13. REMOVE REAR SEAT RECLINING CONTROL CABLE

B117753
B117754
14. REMOVE REAR SEAT LEG SUB-ASSEMBLY

(a) Remove the 4 bolts and the rear seat leg.
B127708
SE
REASSEMBLY
CAUTION:
1. INSTALL REAR SEAT LEG SUB-ASSEMBLY
(a) Install the rear seat leg with the 4 bolts.
B127708

B117754
SE (b) Install the rear seat reclining control cable as shown

in the illustration.
Pink Tape
B127709E01
3. INSTALL RECLINING ADJUSTER LOWER INSIDE

COVER LH
(a) Install the reclining adjuster lower inside cover with
the clip.
4. INSTALL RECLINING ADJUSTER LOWER INSIDE
COVER RH
HINT:
B117752
5. INSTALL RECLINING ADJUSTER UPPER INSIDE

COVER LH
upper inside cover.
6. INSTALL RECLINING ADJUSTER UPPER INSIDE
COVER RH
HINT:
B127661
7. INSTALL REAR SEAT RECLINING COVER LH

reclining cover.
(b) Install the clip.
(c) Tighten the screw.
8. INSTALL REAR SEAT RECLINING COVER RH
HINT:
B117751
9. INSTALL REAR SEATBACK COVER PAD SUB- SE

ASSEMBLY
B117750
(b) Install the rear seat belt hook with the bolt.
(c) Fasten the 2 zippers.
B117748
(d) Engage the hook.
B117747

HINT:
headrest supports.
seatback frame.
Protruding (b) Engage the 2 claws and install the rear seat
headrest support.
B117755E02

ASSEMBLY
(a) Connect the rear seat reclining control cable and
install the rear seat lock control lever.
SE
B127660

lock striker cover.
B127659

ASSEMBLY
Lock Button
B127657E01

HINT:
(a) Push in the lock buttons of the rear seat headrest
Lock Button
B117744E01
SE
INSTALLATION
NOTICE:
rear seat.
(a) Insert the 2 locating pins through the 2 body holes
and install the rear seatback.
(b) Using "Torx" socket wrench E10, tighten the 4 bolts.
B117757
2. INSTALL REAR SEAT CUSHION LOCK HOOK

(a) Engage the 4 claws and install the 2 rear seat
cushion lock hooks.
B117741
SE 3. INSTALL REAR SEAT CUSHION COVER PAD SUB-

ASSEMBLY
(a) Pass the rear seat inner belt through the slit in the
rear seat cushion cover pad.
cushion cover pad.
NOTICE:
Make sure that the rear seat cushion lock hooks
and the rear seat cushion frame are securely
engaged.
B117758 IR-83)
(See page IR-83)

Seat PDF

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Seat PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Seat PDF

Uploaded by

Copyright:

Available Formats

SEAT BELT FRONT PASSENGER SEAT BELT WARNING LIGHT (for Sedan) SB1

FRONT PASSENGER SEAT BELT WARNING LIGHT (for

HAZARD WARNING SIGNAL

for Integrated with Panel:

INSTRUMENT PANEL LOWER

INSTRUMENT PANEL CENTER

HAZARD WARNING SIGNAL

INSTRUMENT PANEL CENTER

HAZARD WARNING SIGNAL

If the result is not as specified, replace the

5. INSTALL INSTRUMENT CLUSTER FINISH PANEL

FRONT PASSENGER SEAT BELT WARNING LIGHT (for

FRONT PASSENGER SEAT

If the result is not as specified, replace the front

SEAT BELT WARNING SYSTEM

COMBINATION METER ASSEMBLY

FRONT DRIVER SEAT BELT

W/ TACHOMETER: FRONT PASSENGER SEAT BELT

CENTER AIRBAG SENSOR

MAIN BODY ECU

COMBINATION METER ASSEMBLY

FRONT DRIVER SEAT BELT WARNING LIGHT

FRONT DRIVER SEAT BELT WARNING LIGHT

MAIN BODY ECU

REAR OCCUPANT CLASSIFICATION

FRONT OCCUPANT CLASSIFICATION SENSOR RH

OCCUPANT CLASSIFICATION ECU

Front Driver Seat Belt

Seat Belt Warning Buzzer for Driver

Front Passenger Seat Belt

Hazard Warning Signal

CAN Communication Line

Front Passenger Seat Belt

Front Seat Inner Belt Front Seat Inner Belt

Sender Receiver Signal Line

HOW TO PROCEED WITH

2 INSPECT BATTERY VOLTAGE

3 CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

(a) Use the intelligent tester to check if the CAN

B GO TO CAN COMMUNICATION SYSTEM

4 PROBLEM SYMPTOMS TABLE

5 OVERALL ANALYSIS AND TROUBLESHOOTING*

(a) DATA LIST / ACTIVE TEST (see page SB-20)

(b) TERMINALS OF ECU (see page SB-14)

PROBLEM SYMPTOMS TABLE

Symptom Suspected area See page

(a) Disconnect the D1 combination meter assembly

If the result is not as specified, there may be a

(f) Waveform 2 (Reference): Using an oscilloscope

2. CENTER AIRBAG SENSOR ASSEMBLY

Center Airbag Sensor Assembly:

Terminal No. Terminal Symbol Destination

Terminal No. Terminal Symbol Destination

3. OCCUPANT CLASSIFICATION ECU

Occupant Classification ECU: U1 J24

(a) Disconnect the J24 occupant classification ECU

If the result is not as specified, there may be a

If the result is not as specified, the combination

Nm (kgfcm, ft*lbf) : Specified torque

Nm (kgfcm, ft*lbf) : Specified torque

Nm (kgfcm, ft*lbf) : Specified torque