Navigator 1.

5
Installation Guide

-1-
Navigator Installation Guide

Navigator Installation Guide

Author: David Chong
Last Revised: June 1, 2015

The software and/or applications described in this document are furnished under a license agreement or
nondisclosure agreement. This document may only be used or copied in accordance with the agreement.

No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical,
including photocopying, recording or information storage and retrieval systems, for any purpose other than the
purchaser's personal use, without the express written permission of Bombardier Inc.

2007-2015 Bombardier Inc. All rights reserved.

Bombardier Aerospace Navigator Administrators Guide

All trademarks belong to their respective owners.

-2-
Navigator Installation Guide

Table of Contents
Navigator Installation Guide 2
Table of Figures ..6
Introduction ..10
Prerequisites .10
Installing Navigator 1.5..10
How to run NavigatorSetup.exe ..10
Installing Navigator Application only (new) .11
Select Setup Language page 11
Welcome to Bombardier Navigator Setup Wizard page .12
License Agreement page 12
No Existing Navigator Application(s) Found page 13
Browse to Alternate Collection Locations page .13
Enable Collection Updates page ..14
Save User Session Information page .14
Internal Docs Alias page .15
Hide Collection Path in Status Bar ..15
Debug Log File page ..16
Effectivity File page 16
Select Destination Location page ...17
Select Start Menu Folder page ..17
Select Additional Tasks page .18
Ready to Install page 18
Installing page 19
Information page 20
Completing the Bombardier Navigator Setup Wizard page .20
Navigator Warning dialog box 21
Navigator 1.5 Splash Screen 21
Navigator 1.5 Application .22
Installing Navigator Application only (update) 22
Select Setup Language page 22
Welcome to Bombardier Navigator Setup Wizard page .23
License Agreement page 23
Existing Navigator Application(s) Found page 24
Older version/current version/newer version dialog box ..24
Existing Navigator Application is an older version dialog box .24
Existing Navigator Application is a current version dialog box 25
Existing Navigator Application is a newer version dialog box .25
Ready to Install page 25
Installing page 26
Information page 26
Completing the Bombardier Navigator Setup Wizard page .27
Installing Aircraft Manual only (new or update) .28
Select Setup Language page 28

-3-
Navigator Installation Guide

Welcome to Bombardier Navigator Setup Wizard page .28

License Agreement page 29
Existing Navigator Application(s) Found page 29
Older version/current version/newer version dialog box ..30
Existing Navigator Application is an older version dialog box .30
Existing Navigator Application is a current version dialog box 30
Existing Navigator Application is a newer version dialog box .30
Select Components page ..31
Select A Collection Folder page .32
Ready to Install page 32
Installing page 33
Information page 33
Completing the Bombardier Navigator Setup Wizard page .34
Navigator 1.5 Splash Screen 34
Aircraft Collections Found dialog box ..35
Navigator 1.5 Application .36
Installing Navigator Application and Aircraft Manual (new) ..37
Select Setup Language page 37
Welcome to Bombardier Navigator Setup Wizard page .37
License Agreement page 38
No Existing Navigator Application(s) Found page 38
Browse to Alternate Collection Locations page .39
Enable Collection Updates page ..39
Save User Session Information page .40
Internal Docs Alias page .40
Hide Collection Path in Status Bar page .41
Debug Log File page ..41
Effectivity File page 42
Select Destination Location page 42
Select Components page ..43
Select A Collection Folder page .43
Select Start Menu Folder page ..44
Select Additional Tasks page ..44
Ready to Install page 45
Installing page 45
Information page 46
Completing the Bombardier Navigator Setup Wizard page.46
Navigator 1.5 Splash Screen 47
Aircraft Collections Found dialog box ..48
Navigator 1.5 Application with Aircraft Manual ...48
Installing Navigator Application and Aircraft Manual (update) ...50
Select Setup Language page 50
Welcome to Bombardier Navigator Setup Wizard page .50
License Agreement page 51

-4-
Navigator Installation Guide

Existing Navigator Application(s) Found page 51

Older version/current version/newer version dialog box ..52
Existing Navigator Application is an older version dialog box .52
Existing Navigator Application is a current version dialog box 52
Existing Navigator Application is a newer version dialog box .52
Select Components page ..53
Select A Collection Folder page .53
Ready to Install page 54
Installing page 55
Information page 55
Completing the Bombardier Navigator Setup Wizard page .56
Navigator 1.5 Splash Screen 56
Aircraft Manual loaded in Navigator 1.5 ...57
Browse to an Existing Navigator Application (App/Manual/Both App and Manual) .57
Select Setup Language page 57
Welcome to Bombardier Navigator Setup Wizard page .58
License Agreement page 58
Existing Navigator Application(s) Found page (Browse to an existing instance) 59
Select Existing Navigator Application Location page (without folder) ..59
Browse For Folder dialog box .60
Select Existing Navigator Application Location page (with folder) ..61
Navigator Application Found (Older, Current or Newer) page ..61
Older Navigator Application Found page .61
Current Navigator Application Found page ...62
Newer Navigator Application Found page ..63
Select Components page ..63
Select Components page (App) ...64
Components Exist dialog box (Manual) ....64
Select Components page (Manual) .....64
Components Exist dialog box (App) ..65
Select Components page (App and Manual) ..65
Select A Collection Folder page .66
Ready to Install page 67
Installing page 68
Information page 68
Completing the Bombardier Navigator Setup Wizard page .69
Navigator 1.5 Application Folder 70
Integrator 1.5 Application Folder ..70
Other Notable Messages .71
Navigator Application is not writable dialog box ..71
Navigator Application is not available dialog box .72
Setup cannot find navigator.ini dialog box .72
Uninstalling Navigator 1.5 and Integrator 1.5 ..73
Customer Support .75

-5-
Navigator Installation Guide

Table of Figures

How to run NavigatorSetup.exe

Figure 1 - Click here to install link to run NavigatorSetup.exe 10
Figure 2 - NavigatorSetup.exe on a Navigator CD ..11

Installing Navigator Application only (new)

Figure 3 - Select Setup Language page 11
Figure 4 - Welcome to the Bombardier Navigator Setup Wizard page 12
Figure 5 - License Agreement page 12
Figure 6 - No Existing Navigator Application(s) Found page 13
Figure 7 - Browse to Alternate Collection Locations page..13
Figure 8 - Enable Collection Updates page14
Figure 9 - Save User Session Information page .14
Figure 10 - Internal Docs Alias page .15
Figure 11 - Hide Collection Path in Status Bar page ..15
Figure 12 - Debug Log File page ..16
Figure 13 - Effectivity File page 16
Figure 14 - Select Destination Location page .17
Figure 15 - Select Start Menu Folder page ..17
Figure 16 - Select Additional Tasks page ..18
Figure 17 - Ready to Install page 19
Figure 18 - Installing page 19
Figure 19 - Information page .20
Figure 20 - Completing the Bombardier Navigator Setup Wizard page ..20
Figure 21 - Navigator Warning dialog box 21
Figure 22 - Navigator 1.5 Splash Screen 21
Figure 23 - Navigator 1.5 Application .22

Installing Navigator Application only (update)

Figure 24 - Select Setup Language page 22
Figure 25 - Welcome to Bombardier Navigator Setup Wizard page .23
Figure 26 - License Agreement page 23
Figure 27 - Existing Navigator Application(s) Found page 24
Figure 28 - Existing Navigator Application is an older version dialog box .24
Figure 29 - Existing Navigator Application is a current version dialog box 25
Figure 30 - Existing Navigator Application is a newer version dialog box .25
Figure 31 - Ready to Install page 26
Figure 32 - Installing page 26
Figure 33 - Information page .27
Figure 34 - Completing the Bombardier Navigator Setup Wizard page ..27

-6-
Navigator Installation Guide

Installing Aircraft Manual Only (new or update)

Figure 35 - Select Setup Language page 28
Figure 36 - Welcome to Bombardier Navigator Setup Wizard page .28
Figure 37 - License Agreement page 29
Figure 38 - Existing Navigator Application(s) Found page 29
Figure 39 - Existing Navigator Application is an older version dialog box .30
Figure 40 - Existing Navigator Application is a current version dialog box 30
Figure 41 - Existing Navigator Application is a newer version dialog box .31
Figure 42 - Select Components page for Aircraft Manual only (new or update) ..31
Figure 43 - Components Exist dialog box .31
Figure 44 - Select A Collection Folder page .32
Figure 45 - Ready to Install page 32
Figure 46 - Installing page 33
Figure 47 - Information page .33
Figure 48 - Completing the Bombardier Navigator Setup Wizard page ..34
Figure 49 - Navigator 1.5 Splash Screen 35
Figure 50 - Aircraft Collections Found dialog box ..35
Figure 51 - Navigator 1.5 Application with Aircraft Manual 36
Figure 52 - Aircraft Manual loaded in Navigator 1.5 36

Installing Navigator Application and Aircraft Manual Only (new)

Figure 53 - Select Setup Language page 37
Figure 54 - Welcome to Bombardier Navigator Setup Wizard page .37
Figure 55 - License Agreement page 38
Figure 56 - No Existing Navigator Application(s) Found page 38
Figure 57 - Browse to Alternate Collection Locations page.39
Figure 58 - Enable Collection Updates page39
Figure 59 - Save User Session Information page 40
Figure 60 - Internal Docs Alias page .40
Figure 61 - Hide Collection Path in Status Bar page ..41
Figure 62 - Debug Log File page ..41
Figure 63 - Effectivity File page 42
Figure 64 - Select Destination Location page .42
Figure 65 - Select Components page for Custom (manually select components) 43
Figure 66 - Select A Collection Folder page .43
Figure 67 - Select Start Menu Folder page ..44
Figure 68 - Select Additional Tasks page ..44
Figure 69 - Ready to Install page 45
Figure 70 - Installing page 46
Figure 71 - Information page .46
Figure 72 - Completing the Bombardier Navigator Setup Wizard page ..47
Figure 73 - Navigator 1.5 Splash Screen 47
Figure 74 - Aircraft Collections Found dialog box ..48
Figure 75 - Navigator 1.5 Application with Aircraft Manual 49

-7-
Navigator Installation Guide

Figure 76 - Aircraft Manual loaded in Navigator 1.5 49

Installing Navigator Application and Aircraft Manual Only (update)

Figure 77 - Select Setup Language page 50
Figure 78 - Welcome to Bombardier Navigator Setup Wizard page 50
Figure 79 - License Agreement page 51
Figure 80 - Existing Navigator Application(s) Found page 51
Figure 81 - Existing Navigator Application is an older version dialog box .52
Figure 82 - Existing Navigator Application is a current version dialog box 52
Figure 83 - Existing Navigator Application is a newer version dialog box .53
Figure 84 - Select Components page for Custom (manually select components) 53
Figure 85 - Select A Collection Folder page .54
Figure 86 - Ready to Install page 54
Figure 87 - Installing page 55
Figure 88 - Information page .55
Figure 89 - Completing the Bombardier Navigator Setup Wizard page ..56
Figure 90 - Navigator 1.5 Splash Screen .56
Figure 91 - Aircraft Manual loaded in Navigator 1.5 .57

Browse to an Existing Navigator Application

Figure 92 - Select Setup Language page .57
Figure 93 - Welcome to Bombardier Navigator Setup Wizard page ..58
Figure 94 - License Agreement page .58
Figure 95 - Existing Navigator Application(s) Found page (Browse to an existing instance) .59
Figure 96 - Select Existing Navigator Application Location page (without folder) 60
Figure 97 - Browse For Folder dialog box ..60
Figure 98 - Select Existing Navigator Application Location page (with folder) ...61
Figure 99 - Older Navigator Application Found page 62
Figure 100 - Current Navigator Application Found page ..62
Figure 101 - Newer Navigator Application Found page ....63
Figure 102 - Select Components page (App) .64
Figure 103 - Components Exist dialog box (Manual) 64
Figure 104 - Select Components page (Manual) .65
Figure 105 - Components Exist dialog box (App) 65
Figure 106 - Select Components page (App and Manual) 66
Figure 107 - Select A Collection Folder page .67
Figure 108 - Ready to Install page .67
Figure 109 - Installing page 68
Figure 110 - Information page .68
Figure 111 - Completing the Bombardier Navigator Setup Wizard page ..69

-8-
Navigator Installation Guide

Navigator 1.5 Application Folder

Figure 112 - Navigator 1.5 Application Folder ..70

Integrator 1.5 Application Folder

Figure 113 - Integrator 1.5 Application Folder .71

Other Notable Messages

Figure 114 - Navigator Application is not writable dialog box .....71
Figure 115 - Navigator Application is not available dialog box .72
Figure 116 - Setup cannot find the navigator.ini file dialog box ..72
Figure 117 Navigator 1.5 navigator.ini file ..72

Uninstalling Navigator 1.5 and Integrator 1.5

Figure 118 - Integrator 1.5 folder (Start Menu) 73
Figure 119 - Uninstall Bombardier Navigator 1.5 (Start Menu) 73
Figure 120 - Bombardier Navigator Uninstall dialog box ..74
Figure 121 - Bombardier Navigator 1.5 Uninstall status page 74
Figure 122 - Navigator 1.5 application successfully uninstalled ..74

-9-
Navigator Installation Guide

Introduction

Welcome to the Navigator 1.5 Installation Guide. This guide contains reference information, advice
and suggestions to help you install new versions of Navigator 1.5 applications.

Note: Integrator 1.5 no longer has its own installer. Integrator 1.5 is now part of the Navigator
1.5 installer. This means when you install a Navigator 1.5 instance, you will automatically
install its Integrator 1.5 instance. The Integrator application folder will be located in the
Navigator application folder (e.g. C:\navigator\integrator).

Prerequisites

It is assumed that you have some knowledge of installing Pages applications and are able to
connect to and use local and networked disk drives in your organization.

To install Navigator instances, you will require write access to the network drive you choose to
install your Navigator application(s). End users should have read access to the network drive(s).

Installing Navigator 1.5

Installation of Navigator 1.5 can be performed by running the NavigatorSetup.exe from the
distribution media. That media may be a CD, DVD, USB Key, External Hard Disk Drive or simply
downloading the file downloaded from iflybombardier.com.

Note: You are NOT required to have administrator rights on your local computer to install the
Navigator application. The application does NOT write any of its settings to the Pages registry.

How to run NavigatorSetup.exe

When you can load the CD distribution media into your CD drive (e.g. D:\), the CD will automatically
launch the navigator_readme.html file. This readme file contains a Click here to install link
under the Install Navigator heading that will allow the user to run the NavigatorSetup.exe by
clicking on the link.

Figure 1 - Click here to install link to run NavigatorSetup.exe

- 10 -
Navigator Installation Guide

Or, if you choose not to use the readme file, you can open your Windows Explorer application, go
into your CD drive (e.g. D:\) and double-click on the NavigatorSetup.exe to launch the executable
and begin the installation process.

Figure 2 - NavigatorSetup.exe on a Navigator CD

Installing Navigator Application only (new)

Users can choose to install the Navigator application only to and install the application for the first
time on a computer with no existing Navigator application(s) installed.

Select Setup Language page

The first page you see is the Select Setup Language page. In this page, you are asked to Select
the language to use during the installation. Most users select English as the language of choice.
Click the Next button to continue.

Figure 3 - Select Setup Language page

- 11 -
Navigator Installation Guide

Welcome to Bombardier Navigator Setup Wizard page

The next page that appears is the Welcome to the Bombardier Navigator Setup Wizard page.
There is nothing to be done here except to click the Next button to continue.

Figure 4 - Welcome to the Bombardier Navigator Setup Wizard page

License Agreement page

The next page that appears is the License Agreement page. Review the license agreement, select
the I accept the agreement button and click the Next button to continue. The License
Agreement file (LICENCE.txt) can be found in the doc folder of the Navigator application folder (e.g.
C:\navigator\doc).

Figure 5 - License Agreement page

- 12 -
Navigator Installation Guide

No Existing Navigator Application(s) Found page

The next page that appears is the No Existing Navigator Application(s) Found page. Since you are
installing Navigator 1.5 for the first time, then you will not have any Navigator instances installed on
the computer. To continue the installation, select the Continue to install a new instance of the
application item and then click on the Next button.

Figure 6 - No Existing Navigator Application(s) Found page

Browse to Alternate Collection Locations page

This is the Browse to Alternate Collection Locations page, which normally appears after the List
of Integrator Application(s) page in this type of installation. This page allows you to browse to
other Navigator collection locations. The Enable browsing to alternate collection locations box is
checked off by default to allow users to browse to other collection locations. You can uncheck this
box if you do not want to browse to other collection locations. Click the Next button to continue.

Figure 7 - Browse to Alternate Collection Locations page

- 13 -
Navigator Installation Guide

Enable Collection Updates page

The next page that appears is the Enable Collection Updates page. This page allows you to update
your Navigator collection by adding Temporary Revisions (TRs) and/or Customer Authored
Documents (Custdocs). Enable the check box if you will manage Navigator updates for other users.
Disable the check box if the Navigator updates are managed by someone else (e.g. Navigator
Administrator). Click the Next button to continue.

Figure 8 - Enable Collection Updates page

Save User Session Information page

The next page that appears is the Save User Session Information page. This page allows you to
save and retain the user session information between sessions. Check off the box to enable support
for saving information. Uncheck the box to disable support for saving information if you do not
want to save session information or your Navigator application will be run from a multi-user system
(e.g. Citrix server) that is not configured to allow individual user settings to be saved. Click the Next
button to continue.

Figure 9 - Save User Session Information page

- 14 -
Navigator Installation Guide

Internal Docs Alias page

The next page that appears is the Internal Docs Alias page. This page allows you to provide an
alias to your internal docs so that Navigator knows what name to refer to. Type in the name of your
Internal Docs that you want Navigator to refer to and click the Next button to continue.

Figure 10 - Internal Docs Alias page

Hide Collection Path in Status Bar page

The next page that appears is the Hide Collection Path In Status Bar. This page allows you to hide
the path information displayed in the status bar for a collection that is currently opened. Uncheck
the box if the installed Navigator application manages collection manuals in multiple locations. It
will be easier to confirm which collection location is being managed by viewing the path in the
status bar. Check the box if you want to hide the path information to the collection. Click the Next
button to continue.

Figure 11 - Hide Collection Path in Status Bar page

- 15 -
Navigator Installation Guide

Debug Log File page

The next page that appears is the Debug Log File. This page allows Navigator to add debugging
information to the log file. By default, Navigator will not add any debugging information into the log
file so by default the DebugLog entry in the navigator.ini file will be set to False. If you do want to
add debugging information into the log file, then set the DebugLog entry to True in the
navigator.ini file. Click on the Next button to continue.

Figure 12 - Debug Log File page

Effectivity File page

The next page that appears is the Effectivity File page. This page allows Navigator to add an
effectivity file for the purpose of effectivity filtering. By default, the effectivity file will be called
effectivity.ini and will be located in the Navigator application folder (e.g. C:\navigator). Navigator
does not recommend you rename this file since the application looks for this filename to use.

Figure 13 - Effectivity File page

- 16 -
Navigator Installation Guide

Select Destination Location page

The next page that appears is the Select Destination Location page. This page allows you to select
the destination location of where your Navigator application will be installed. Type in the path of
where you want your Navigator application to be installed (e.g. C:\navigator) or browse to a
destination location. Click on the Next button to continue.

Figure 14 - Select Destination Location page

Select Start Menu Folder page

The next page that appears is the Select Start Menu Folder page. This page allows the user to
create the folder name in the Start Menu folder for the Navigator application you are currently
installing. You can type the folder name in the input box or click the Browse button to select a
different folder. Click the Next button to continue.

Figure 15 - Select Start Menu Folder page

- 17 -
Navigator Installation Guide

Select Additional Tasks page

The next page that appears is the Select Additional Tasks page. This page allows the user to select
any additional tasks to be performed during the installation process. The user has the option of
creating a desktop icon and/or Quick launch icon by checking off the appropriate box in the page.
The user can also choose to not create either icon and leave both boxes unchecked. Click on the
Next button to continue.

Figure 16 - Select Additional Tasks page

Ready to Install page

The next page that appears is the Ready to Install page. This page informs the user that Setup is
now Ready to Install the Navigator application. The page lists all the settings that you selected
from the previous pages. You can click on the Back button to review or change any settings. Click
on the Install button to begin installation of the Navigator application.

Note: The settings that you see in the Ready to Install page below only appear when you are
performing a Navigator Application Only installation by installing a new instance. These settings
are applied only to the navigator.ini file located in your Navigator application folder (e.g.
C:\navigator).

- 18 -
Navigator Installation Guide

Figure 17 - Ready to Install page

Installing page

The next page that appears is the Installing page. This page performs the installation of the
Navigator application (along with the Integrator application) as it extracts the files from the
NavigatorSetup.exe file. Once the installation process is complete, Setup will take you to the next
page so you will not need to click on the Next button.

Figure 18 - Installing page

- 19 -
Navigator Installation Guide

Information page

The next page that appears is the Information page. This page lists the History of the Navigator
application, what new features were added as well as changes made to the application. Review the
History file and click the Next button to continue. The History file (HISTORY.txt) can be found
in the doc folder of the Navigator application folder (e.g. C:\navigator\doc).

Figure 19 - Information page

Completing the Bombardier Navigator Setup Wizard page

The final page in the Navigator Installation Only process is the Completing the Bombardier
Navigator Setup Wizard page. This page tells the user that the installation process is finished. You
can Launch Bombardier Navigator by checking off the box or you can leave the box unchecked if
you do not wish to launch the application. Click on the Finish button to exit the setup.

Figure 20 - Completing the Bombardier Navigator Setup Wizard page

- 20 -
Navigator Installation Guide

Navigator Warning dialog box

If the user decides to launch the Navigator 1.5 application once the installation process has
completed, the Navigator Warning dialog box will appear if and only if Navigator is unable to find
a default Navigator collection. The message WARNING: A default collection was not found (or
selected). The application will open without a collection. Please select a collection using the File
menu will appear. Information on how to open a new collection can be found in the UserGuide.pdf
file, located in your doc folder of the Navigator application folder (e.g. C:\navigator\doc). Click the
OK button to continue.

Figure 21 - Navigator Warning dialog box

Navigator 1.5 Splash Screen

The screen that appears after clicking on the OK button is the Navigator Splash Screen. The
splash screen will appear for a few seconds before it disappears so there is nothing that the user
needs to do. This is what the splash screen looks like for Navigator 1.5.

Figure 22 - Navigator 1.5 Splash Screen

- 21 -
Navigator Installation Guide

Navigator 1.5 Application

Once the splash screen disappears the Navigator 1.5 application will appear and the installation
process has completed. The application is now ready for use.

Figure 23 - Navigator 1.5 Application

Installing Navigator Application only (update)

Users can choose to install the Navigator application to update an existing Navigator instance. Users
can choose this type of installation to upgrade one or more existing Navigator application(s)
installed on the computer.

Select Setup Language page

The first page you see is the Select Setup Language page. In this page, you are asked to Select
the language to use during the installation. Most users select English as the language of choice,
however, you can click on the drop-down list to select another language to install Navigator in. Click
the Next button to continue.

Figure 24 - Select Setup Language page

- 22 -
Navigator Installation Guide

Welcome to Bombardier Navigator Setup Wizard page

The next page that appears is the Welcome to the Bombardier Navigator Setup Wizard page.
There is nothing to be done here except to click the Next button to continue.

Figure 25 - Welcome to the Bombardier Navigator Setup Wizard page

License Agreement page

The next page that appears is the License Agreement page. Review the license agreement, select
the I accept the agreement button and click the Next button to continue. The License
Agreement file (LICENCE.txt) can be found in the doc folder of the Navigator application folder (e.g.
C:\navigator\doc).

Figure 26 - License Agreement page

- 23 -
Navigator Installation Guide

Existing Navigator Application(s) Found page

The next page that appears is the Existing Navigator Application(s) Found page. This page will
display all the Navigator instances you currently have installed on your computer. Select the existing
Navigator instance you want to upgrade and click the Next button to continue.

Figure 27 - Existing Navigator Application(s) Found page

Older version/current version/newer version dialog box

When you select an existing Navigator instance, a dialog box appears depending on whether the
version of the existing instance is an older or current or newer version. Below are the dialog boxes
for each case.

Existing Navigator Application is an older version dialog box

If the user decides to upgrade an existing Navigator instance that contains an older version of the
application, then Setup will override the application at that location. After clicking on the OK
button, the user can choose to click the Next button to install the application.

Figure 28 - Existing Navigator Application is an older version dialog box

- 24 -
Navigator Installation Guide

Existing Navigator Application is a current version dialog box

If the user decides to re-install an existing Navigator instance that contains a current version of the
application, then Setup will override the application if this is a re-install. After clicking on the OK
button, the user can choose to click the Next button to re-install the application or click the Back
button and choose another existing Navigator instance.

Figure 29 - Existing Navigator Application is a current version dialog box

Existing Navigator Application is a newer version dialog box

If the user decides to re-install an existing Navigator instance that contains a newer version of the
application, then Setup will NOT override the application at that location. After clicking on the OK
button, the user can choose to click the Next button to install an aircraft manual or click the Back
button and choose another existing Navigator instance.

Figure 30 - Existing Navigator Application is a newer version dialog box

Ready to Install page

The next page that appears is the Ready to Install page. This page informs the user that Setup is
now Ready to Install the Navigator application. Click on the Install button to begin installation of
the Navigator application.

- 25 -
Navigator Installation Guide

Figure 31 - Ready to Install page

Installing page

The next page that appears is the Navigator Installing page. This page performs the installation of
the Navigator application (along with the Integrator application) as it extracts the files from the
NavigatorSetup.exe file. Once the installation process is complete, Setup will take you to the next
page so you will not need to click on the Next button.

Figure 32 - Installing page

Information page

The next page that appears is the Navigator Information page. This page lists the History of the
Navigator application, what new features were added as well as changes made to the application.
Review the History file and click the Next button to continue. The History file (HISTORY.txt)
can be found in the doc folder of the Navigator application folder (e.g. C:\navigator\doc).

- 26 -
Navigator Installation Guide

Figure 33 - Information page

Completing the Bombardier Navigator Setup Wizard page

The final page that appears is the Completing the Bombardier Navigator Setup Wizard page. This
page tells the user that the installation process is finished. Click on the Finish button to exit the
setup.

Note: This Completing the Bombardier Navigator Setup Wizard page does not allow you to
launch the Navigator application upon completion of setup. Only when performing a
Navigator Application Only installation by installing a new instance will you be able to launch
the application. For this type of installation, if you wish to launch the application after
installation, you will need to double-click its desktop or quick launch icon or double-click the
navigator.exe file in the Navigator application folder (e.g. C:\navigator).

Figure 34 - Completing the Bombardier Navigator Setup Wizard page

- 27 -
Navigator Installation Guide

Installing Aircraft Manual only (new or update)

Select Setup Language page

The first page you see is the Select Setup Language page. In this page, you are asked to Select
the language to use during the installation. Most users select English as the language of choice,
however, you can click on the drop-down list to select another language to install Navigator in. Click
the Next button to continue.

Figure 35 - Select Setup Language page

Welcome to Bombardier Navigator Setup Wizard page

The next page that appears is the Welcome to the Bombardier Navigator Setup Wizard page.
There is nothing to be done here except to click the Next button to continue.

Figure 36 - Welcome to the Bombardier Navigator Setup Wizard page

- 28 -
Navigator Installation Guide

License Agreement page

The next page that appears is the License Agreement page. Review the license agreement, select
the I accept the agreement button and click the Next button to continue. The License
Agreement file (LICENCE.txt) can be found in the doc folder of the Navigator application folder (e.g.
C:\navigator\doc).

Figure 37 - License Agreement page

Existing Navigator Application(s) Found page

The next page that appears is the Existing Navigator Application(s) Found page. This page will
display all the Navigator instances you currently have installed on your computer. Select the existing
Navigator instance you want to upgrade and click the Next button to continue.

Figure 38 - Existing Navigator Application(s) Found page

- 29 -
Navigator Installation Guide

Older version/current version/newer version dialog box

When you select an existing Navigator instance, a dialog box appears depending on whether the
version of the existing instance is an older or current or newer version. Below are the dialog boxes
for each case.

Existing Navigator Application is an older version dialog box

If the user decides to upgrade an existing Navigator instance that contains an older version of the
application, then Setup will override the application at that location. After clicking on the OK
button, the user can choose to click the Next button to install the application.

Figure 39 - Existing Navigator Application is an older version dialog box

Existing Navigator Application is a current version dialog box

If the user decides to re-install an existing Navigator instance that contains a current version of the
application, then Setup will override the application if this is a re-install. After clicking on the OK
button, the user can choose to click the Next button to re-install the application or click the Back
button and choose another existing Navigator instance.

Figure 40 - Existing Navigator Application is a current version dialog box

Existing Navigator Application is a newer version dialog box

If the user decides to re-install an existing Navigator instance that contains a newer version of the
application, then Setup will NOT override the application at that location. After clicking on the OK
button, the user can choose to click the Next button to install an aircraft manual or click the Back
button and choose another existing Navigator instance.

- 30 -
Navigator Installation Guide

Figure 41 - Existing Navigator Application is a newer version dialog box

Select Components page

The next page that appears is the Select Components page. This page allows the user to choose
which component to install. To install the Aircraft Manual only, the user will select the Aircraft
Manual Only (new or update) item from the drop-down list. This selection will check off the
Aircraft Manual box. The same applies to installing a new Aircraft Manual or updating an existing
Aircraft Manual. Click on the Next button to continue.

Figure 42 - Select Components page for Aircraft Manual only (new or update)

If you are only adding an Aircraft Manual, then the Components Exist dialog box will appear. This
dialog box notifies the user that the Navigator application is already installed and deselecting these
components will not uninstall them. Click the Yes button to continue.

Figure 43 - Components Exist dialog box

- 31 -
Navigator Installation Guide

Select A Collection Folder page

The next page that appears is the Select A Collection Folder page. This page allows the user to
choose when collection folder (e.g. C:\navigator\collects) setup should install the aircraft manual.
You can type in the full path of the collection folder or you can click on the Browse button to
browse to the collection folder. Click on the Next button to continue.

Figure 44 - Select A Collection Folder page

Ready to Install page

The next page that appears is the Ready to Install page. This page informs the user that Setup is
now Ready to Install the Navigator application. You can click on the Back button to review or
change any settings. Click on the Install button to begin installation of the Navigator application.

Figure 45 - Ready to Install page

- 32 -
Navigator Installation Guide

Installing page

The next page that appears is the Navigator Installing page. This page performs the installation of
the Navigator application (along with the Integrator application) as it extracts the files from the
NavigatorSetup.exe file. Once the installation process is complete, Setup will take you to the next
page so you will not need to click on the Next button.

Figure 46 - Installing page

Information page

The next page that appears is the Navigator Information page. This page lists the History of the
Navigator application, what new features were added as well as changes made to the application.
Review the History file and click the Next button to continue. The History file (HISTORY.txt)
can be found in the doc folder of the Navigator application folder (e.g. C:\navigator\doc).

Figure 47 - Information page

- 33 -
Navigator Installation Guide

Completing the Bombardier Navigator Setup Wizard page

The final page that appears is the Completing the Bombardier Navigator Setup Wizard page. This
page tells the user that the installation process is finished. Click on the Finish button to exit the
setup.

Note: This Completing the Bombardier Navigator Setup Wizard page does not allow you to
launch the Navigator application upon completion of setup. Only when performing a
Navigator Application Only installation by installing a new instance will you be able to launch
the application. For this type of installation, if you wish to launch the application after
installation, you will need to double-click its desktop or quick launch icon or double-click the
navigator.exe file in the Navigator application folder (e.g. C:\navigator).

Figure 48 - Completing the Bombardier Navigator Setup Wizard page

Navigator 1.5 Splash Screen

The screen that appears after clicking on the OK button is the Navigator Splash Screen. The
splash screen will appear for a few seconds before it disappears so there is nothing that the user
needs to do. This is what the splash screen looks like for Navigator 1.5.

- 34 -
Navigator Installation Guide

Figure 49 - Navigator 1.5 Splash Screen

Aircraft Collections Found dialog box

If the user decides to launch the Navigator 1.5 application once the installation process has
completed, the Aircraft Collections Found dialog box will appear since the user installed both the
Navigator application and the Aircraft Manual. The message Please select an aircraft collection to
open will appear. The dialog box will indicate the aircraft series the installed manual belongs to
(e.g. Q400). Click the OK button to continue.

Note: The Aircraft Collections Found dialog box only appears when you install a new Aircraft
Manual into your collects folder for the first time. If the user is overwriting the same existing
Aircraft Manual in the collects folder, then this page will not appear in the installation process.

Figure 50 - Aircraft Collections Found dialog box

- 35 -
Navigator Installation Guide

Navigator 1.5 Application

The Navigator 1.5 application will appear and the installation process has completed. The Aircraft
Manual installed during the installation process will appear in the Navigator application. The
application is now ready for use.

Figure 51 - Navigator 1.5 Application with Aircraft Manual

Click on the manual button (e.g. AMM button) to load the manual in Navigator. This is what the
aircraft manual will look like after installation.

Figure 52 - Aircraft Manual loaded in Navigator 1.5

- 36 -
Navigator Installation Guide

Installing Navigator Application and Aircraft Manual (new)

Select Setup Language page

The first page you see is the Select Setup Language page. In this page, you are asked to Select
the language to use during the installation. Most users select English as the language of choice,
however, you can click on the drop-down list to select another language to install Navigator in. Click
the Next button to continue.

Figure 53 - Select Setup Language page

Welcome to Bombardier Navigator Setup Wizard page

The next page that appears is the Welcome to the Bombardier Navigator Setup Wizard page.
There is nothing to be done here except to click the Next button to continue.

Figure 54 - Welcome to the Bombardier Navigator Setup Wizard page

- 37 -
Navigator Installation Guide

License Agreement page

The next page that appears is the License Agreement page. Review the license agreement, select
the I accept the agreement button and click the Next button to continue. The License
Agreement file (LICENCE.txt) can be found in the doc folder of the Navigator application folder (e.g.
C:\navigator\doc).

Figure 55 - License Agreement page

No Existing Navigator Application(s) Found page

The next page that appears is the No Existing Navigator Application(s) Found page. Since you are
installing Navigator 1.5 for the first time, then you will not have any Navigator instances installed on
the computer. To continue the installation, select the Continue to install a new instance of the
application item and then click on the Next button.

Figure 56 - No Existing Navigator Application(s) Found page

- 38 -
Navigator Installation Guide

Browse to Alternate Collection Locations page

This is the Browse to Alternate Collection Locations page, which normally appears after the List
of Integrator Application(s) page in this type of installation. This page allows you to browse to
other Navigator collection locations. The Enable browsing to alternate collection locations box is
checked off by default to allow users to browse to other collection locations. You can uncheck this
box if you do not want to browse to other collection locations. Click the Next button to continue.

Figure 57 - Browse to Alternate Collection Locations page

Enable Collection Updates page

The next page that appears is the Enable Collection Updates page. This page allows you to update
your Navigator collection by adding Temporary Revisions (TRs) and/or Customer Authored
Documents (Custdocs). Enable the check box if you will manage Navigator updates for other users.
Disable the check box if the Navigator updates are managed by someone else (e.g. Navigator
Administrator). Click the Next button to continue.

Figure 58 - Enable Collection Updates page

- 39 -
Navigator Installation Guide

Save User Session Information page

The next page that appears is the Save User Session Information page. This page allows you to
save and retain the user session information between sessions. Check off the box to enable support
for saving information. Uncheck the box to disable support for saving information if you do not
want to save session information or your Navigator application will be run from a multi-user system
(e.g. Citrix server) that is not configured to allow individual user settings to be saved. Click the Next
button to continue.

Figure 59 - Save User Session Information page

Internal Docs Alias page

The next page that appears is the Internal Docs Alias page. This page allows you to provide an
alias to your internal docs so that Navigator knows what name to refer to. Type in the name of your
Internal Docs that you want Navigator to refer to and click the Next button to continue.

Figure 60 - Internal Docs Alias page

- 40 -
Navigator Installation Guide

Hide Collection Path in Status Bar page

The next page that appears is the Hide Collection Path In Status Bar. This page allows you to hide
the path information displayed in the status bar for a collection that is currently opened. Uncheck
the box if the installed Navigator application manages collection manuals in multiple locations. It
will be easier to confirm which collection location is being managed by viewing the path in the
status bar. Check the box if you want to hide the path information to the collection. Click the Next
button to continue.

Figure 61 - Hide Collection Path in Status Bar page

Debug Log File page

The next page that appears is the Debug Log File. This page allows Navigator to add debugging
information to the log file. By default, Navigator will not add any debugging information into the log
file so by default the DebugLog entry in the navigator.ini file will be set to False. If you do want to
add debugging information into the log file, then set the DebugLog entry to True in the
navigator.ini file. Click on the Next button to continue.

Figure 62 - Debug Log File page

- 41 -
Navigator Installation Guide

Effectivity File page

The next page that appears is the Effectivity File page. This page allows Navigator to add an
effectivity file for the purpose of effectivity filtering. By default, the effectivity file will be called
effectivity.ini and will be located in the Navigator application folder (e.g. C:\navigator). Navigator
does not recommend you rename this file since the application looks for this filename to use.

Figure 63 - Effectivity File page

Select Destination Location page

The next page that appears is the Select Destination Location page. This page allows you to select
the destination location of where your Navigator application will be installed. Type in the path of
where you want your Navigator application to be installed (e.g. C:\navigator) or browse to a
destination location. Click on the Next button to continue.

Figure 64 - Select Destination Location page

- 42 -
Navigator Installation Guide

Select Components page

The next page that appears is the Select Components page. This page asks the user which
components to install. When only installing both the Navigator application and Aircraft Manual, the
user will select the Custom (manually select components) item from the drop-down list. This
selection will check off both the Navigator Application and the Aircraft Manual boxes. Click on
the Next button to continue.

Figure 65 - Select Components page for Custom (manually select components)

Select A Collection Folder page

The next page that appears is the Select A Collection Folder page. This page allows the user to
choose when collection folder (e.g. C:\navigator\collects) setup should install the aircraft manual.
You can type in the full path of the collection folder or you can click on the Browse button to
browse to the collection folder. Click on the Next button to continue.

Figure 66 - Select A Collection Folder page

- 43 -
Navigator Installation Guide

Select Start Menu Folder page

The next page that appears is the Select Start Menu Folder page. This page allows the user to
create the folder name in the Start Menu folder for the Navigator application you are currently
installing. You can type the folder name in the input box or click the Browse button to select a
different folder. Click the Next button to continue.

Figure 67 - Select Start Menu Folder page

Select Additional Tasks page

The next page that appears is the Select Additional Tasks page. This page allows the user to select
any additional tasks to be performed during the installation process. The user has the option of
creating a desktop icon and/or Quick launch icon by checking off the appropriate box in the page.
The user can also choose to not create either icon and leave both boxes unchecked. Click on the
Next button to continue.

Figure 68 - Select Additional Tasks page

- 44 -
Navigator Installation Guide

Ready to Install page

The next page that appears is the Ready to Install page. This page informs the user that Setup is
now Ready to Install the Navigator application. The page lists all the settings that you selected
from the previous pages. You can click on the Back button to review or change any settings. Click
on the Install button to begin installation of the Navigator application.

Note: The settings that you see in the Ready to Install page below only appear when you are
performing a Navigator Application Only installation by installing a new instance. These settings
are applied only to the navigator.ini file located in your Navigator application folder (e.g.
C:\navigator).

Figure 69 - Ready to Install page

Installing page

The next page that appears is the Navigator Installing page. This page performs the installation of
the Navigator application (along with the Integrator application) as it extracts the files from the
NavigatorSetup.exe file. Once the installation process is complete, Setup will take you to the next
page so you will not need to click on the Next button.

- 45 -
Navigator Installation Guide

Figure 70 - Installing page

Information page

The next page that appears is the Navigator Information page. This page lists the History of the
Navigator application, what new features were added as well as changes made to the application.
Review the History file and click the Next button to continue. The History file (HISTORY.txt)
can be found in the doc folder of the Navigator application folder (e.g. C:\navigator\doc).

Figure 71 - Information page

Completing the Bombardier Navigator Setup Wizard page

The final page in the Navigator Installation Only process is the Completing the Bombardier
Navigator Setup Wizard page. This page tells the user that the installation process is finished. You
can Launch Bombardier Navigator by checking off the box or you can leave the box unchecked if
you do not wish to launch the application. Click on the Finish button to exit the setup.

- 46 -
Navigator Installation Guide

Figure 72 - Completing the Bombardier Navigator Setup Wizard page

Navigator 1.5 Splash Screen

The screen that appears after clicking on the OK button is the Navigator Splash Screen. The
splash screen will appear for a few seconds before it disappears so there is nothing that the user
needs to do. This is what the splash screen looks like for Navigator 1.5.

Figure 73 - Navigator 1.5 Splash Screen

- 47 -
Navigator Installation Guide

Aircraft Collections Found dialog box

If the user decides to launch the Navigator 1.5 application once the installation process has
completed, the Aircraft Collections Found dialog box will appear since the user installed both the
Navigator application and the Aircraft Manual. The message Please select an aircraft collection to
open will appear. The dialog box will indicate the aircraft series the installed manual belongs to
(e.g. Q400). Click the OK button to continue.

Note: The Aircraft Collections Found dialog box only appears when you install a new Aircraft
Manual into your collects folder for the first time. If the user is overwriting the same existing
Aircraft Manual in the collects folder, then this page will not appear in the installation process.

Figure 74 - Aircraft Collections Found dialog box

Navigator 1.5 Application with Aircraft Manual

The Navigator 1.5 application will appear and the installation process has completed. The Aircraft
Manual installed during the installation process will appear in the Navigator application. The
application is now ready for use.

- 48 -
Navigator Installation Guide

Figure 75 - Navigator 1.5 Application with Aircraft Manual

Click on the manual button (e.g. AMM button) to load the manual in Navigator. This is what the
aircraft manual will look like after installation.

Figure 76 - Aircraft Manual loaded in Navigator 1.5

- 49 -
Navigator Installation Guide

Installing Navigator Application and Aircraft Manual (update)

Select Setup Language page

The first page you see is the Select Setup Language page. In this page, you are asked to Select
the language to use during the installation. Most users select English as the language of choice,
however, you can click on the drop-down list to select another language to install Navigator in. Click
the Next button to continue.

Figure 77 - Select Setup Language page

Welcome to Bombardier Navigator Setup Wizard page

The next page that appears is the Welcome to the Bombardier Navigator Setup Wizard page.
There is nothing to be done here except to click the Next button to continue.

Figure 78 - Welcome to the Bombardier Navigator Setup Wizard page

- 50 -
Navigator Installation Guide

License Agreement page

The next page that appears is the License Agreement page. Review the license agreement, select
the I accept the agreement button and click the Next button to continue. The License
Agreement file (LICENCE.txt) can be found in the doc folder of the Navigator application folder (e.g.
C:\navigator\doc).

Figure 79 - License Agreement page

Existing Navigator Application(s) Found page

The next page that appears is the Existing Navigator Application(s) Found page. This page will
display all the Navigator instances you currently have installed on your computer. Select the existing
Navigator instance you want to upgrade and click the Next button to continue.

Figure 80 - Existing Navigator Application(s) Found page

- 51 -
Navigator Installation Guide

Older version/current version/newer version dialog box

When you select an existing Navigator instance, a dialog box appears depending on whether the
version of the existing instance is an older or current or newer version. Below are the dialog boxes
for each case.

Existing Navigator Application is an older version dialog box

If the user decides to upgrade an existing Navigator instance that contains an older version of the
application, then Setup will override the application at that location. After clicking on the OK
button, the user can choose to click the Next button to install the application.

Figure 81 - Existing Navigator Application is an older version dialog box

Existing Navigator Application is a current version dialog box

If the user decides to re-install an existing Navigator instance that contains a current version of the
application, then Setup will override the application if this is a re-install. After clicking on the OK
button, the user can choose to click the Next button to re-install the application or click the Back
button and choose another existing Navigator instance.

Figure 82 - Existing Navigator Application is a current version dialog box

Existing Navigator Application is a newer version dialog box

If the user decides to re-install an existing Navigator instance that contains a newer version of the
application, then Setup will NOT override the application at that location. After clicking on the OK
button, the user can choose to click the Next button to install an aircraft manual or click the Back
button and choose another existing Navigator instance.

- 52 -
Navigator Installation Guide

Figure 83 - Existing Navigator Application is a newer version dialog box

Select Components page

The next page that appears is the Select Components page. This page asks the user which
components to install. When only installing both the Navigator application and Aircraft Manual, the
user will select the Custom (manually select components) item from the drop-down list. This
selection will check off both the Navigator Application and the Aircraft Manual boxes. Click on
the Next button to continue.

Figure 84 - Select Components page for Custom (manually select components)

Select A Collection Folder page

The next page that appears is the Select A Collection Folder page. This page allows the user to
choose when collection folder (e.g. C:\navigator\collects) setup should install the aircraft manual.
You can type in the full path of the collection folder or you can click on the Browse button to
browse to the collection folder. Click on the Next button to continue.

- 53 -
Navigator Installation Guide

Figure 85 - Select A Collection Folder page

Ready to Install page

The next page that appears is the Ready to Install page. This page informs the user that Setup is
now Ready to Install the Navigator application. You can click on the Back button to review or
change any settings. Click on the Install button to begin installation of the Navigator application.

Figure 86 - Ready to Install page

- 54 -
Navigator Installation Guide

Installing page

The next page that appears is the Navigator Installing page. This page performs the installation of
the Navigator application (along with the Integrator application) as it extracts the files from the
NavigatorSetup.exe file. Once the installation process is complete, Setup will take you to the next
page so you will not need to click on the Next button.

Figure 87 - Installing page

Information page

The next page that appears is the Navigator Information page. This page lists the History of the
Navigator application, what new features were added as well as changes made to the application.
Review the History file and click the Next button to continue. The History file (HISTORY.txt)
can be found in the doc folder of the Navigator application folder (e.g. C:\navigator\doc).

Figure 88 - Information page

- 55 -
Navigator Installation Guide

Completing the Bombardier Navigator Setup Wizard page

The final page in the process is the Completing the Bombardier Navigator Setup Wizard page. This
page tells the user that the installation process is finished. You can Launch Bombardier Navigator
by checking off the box or you can leave the box unchecked if you do not wish to launch the
application. Click on the Finish button to exit the setup.

Figure 89 - Completing the Bombardier Navigator Setup Wizard page

Navigator 1.5 Splash Screen

The screen that appears after clicking on the OK button is the Navigator Splash Screen. The
splash screen will appear for a few seconds before it disappears so there is nothing that the user
needs to do. This is what the splash screen looks like for Navigator 1.5.

Figure 90 - Navigator 1.5 Splash Screen

- 56 -
Navigator Installation Guide

Aircraft Manual loaded in Navigator 1.5

The Navigator 1.5 application will appear and the installation process has completed. The Aircraft
Manual installed during the installation process will appear in the Navigator application. The
application is now ready for use. This is what the aircraft manual will look like after installation.

Figure 91 - Aircraft Manual loaded in Navigator 1.5

Browse to an Existing Navigator Application (App/Manual/Both App and Manual)

Select Setup Language page

The first page you see is the Select Setup Language page. In this page, you are asked to Select
the language to use during the installation. Most users select English as the language of choice,
however, you can click on the drop-down list to select another language to install Navigator in. Click
the Next button to continue.

Figure 92 - Select Setup Language page

- 57 -
Navigator Installation Guide

Welcome to the Bombardier Navigator Setup Wizard page

The next page that appears is the Welcome to the Bombardier Navigator Setup Wizard page.
There is nothing to be done here except to click the Next button to continue.

Figure 93 - Welcome to the Bombardier Navigator Setup Wizard page

License Agreement page

The next page that appears is the License Agreement page. Review the license agreement, select
the I accept the agreement button and click the Next button to continue. The License
Agreement file (LICENCE.txt) can be found in the doc folder of the Navigator application folder (e.g.
C:\navigator\doc).

Figure 94 - License Agreement page

- 58 -
Navigator Installation Guide

Existing Navigator Application(s) Found page (Browse to an existing instance)

The next page that appears is the Existing Navigator Application(s) Found page. This page will
display all the Navigator instances you currently have installed on your computer. However, if the
user wants to upgrade an existing Navigator instance but is unable to find that Navigator instance in
the list of existing Navigator Application(s), then the user can select the Browse to an existing
instance of the Navigator application not listed above item and browse to the location of that
Navigator instance. Click the Next button to continue.

Figure 95 - Existing Navigator Application(s) Found page (Browse to an existing instance)

Select Existing Navigator Application Location page (without folder)

The next page that appears is the Select Existing Navigator Application Location page without the
folder of the existing Navigator instance. This page allows the user to browse to an existing
installation of the application. The user selects the folder where Setup can find the existing instance
of the Navigator application to upgrade (if required) or re-install the application. Click on the
Browse button to browse to the folder.

- 59 -
Navigator Installation Guide

Figure 96 - Select Existing Navigator Application Location page (without folder)

Browse For Folder dialog box

When the user clicks on the Browse button, the Browse For Folder dialog box will appear. The
user would browse to the folder of the existing Navigator instance that they wish to upgrade (if
required) or re-install (e.g. C:\navigator). Click on the OK button to continue.

Figure 97 - Browse For Folder dialog box

- 60 -
Navigator Installation Guide

Select Existing Navigator Application Location page (with folder)

After clicking on the OK button, the user will return to the Select Existing Navigator Application
Location page with the folder of the existing Navigator instance selected (e.g. C:\navigator). Click
on the Next button to continue.

Figure 98 - Select Existing Navigator Application Location page (with folder)

Navigator Application Found (Older, Current or Newer) page

The next page that appears is the Navigator Application Found page. However, this page will
depend on whether the existing Navigator application found is an older version, a current version or
a newer version.

Older Navigator Application Found page

If the user selects an older version of the Navigator application, then the Older Navigator
Application Found page will appear. It is recommended that the user upgrade the existing
application (all settings will be maintained). Upgrading the existing application will preserve the
existing settings. Click on the Next button to continue.

- 61 -
Navigator Installation Guide

Figure 99 - Older Navigator Application Found page

Current Navigator Application Found page

If the user selects a current (up-to-date) version of the Navigator application, then the Current
Navigator Application Found page will appear. Users have the option of adding a manual to the
instance and optionally re-install the application. Click on the Next button to continue.

Figure 100 - Current Navigator Application Found page

- 62 -
Navigator Installation Guide

Newer Navigator Application Found page

If the user selects a newer version of the Navigator application, then the Newer Navigator
Application Found page will appear. It is recommended that the user DO NOT upgrade the
existing application since the most current version is already installed. The user has the option of
exiting Setup or continuing by installing a manual. Click on the Next button to continue.

Figure 101 - Newer Navigator Application Found page

Select Components page

Note: For the Browse to an Existing Navigator Application method, if you run the
NavigatorSetup.exe on its own, i.e. you are not running NavigatorSetup.exe from a Navigator
revision manual image folder, the Select Components page will not appear during the Setup
process. Setup already knows you are installing the Navigator Application only.

You will only see the Select Components page during Setup when you run the
NavigatorSetup.exe from a Navigator revision manual image folder. In the Select Components
page, you can choose to install the Aircraft Manual only or install both the Navigator Application
and the Aircraft Manual. You can also choose to install the Navigator Application only at this
point.

The next page that appears is the Select Components page. This page asks the user which
components to install. The user has the option of installing the Navigator Application only, adding
an Aircraft Manual only or installing both the Navigator Application and Aircraft Manual.

- 63 -
Navigator Installation Guide

Select Components page (App)

When updating the existing Navigator application only, the user will select the Navigator
Application Only (new or update) item from the drop-down list. This selection will only check off
the Navigator Application box. Click on the Next button to continue.

Figure 102 - Select Components page (App)

Components Exist dialog box (Manual)

If you are only updating an existing Navigator application only and there is an existing Aircraft
Manual installed, then the Components Exist dialog box will appear. Otherwise, this dialog box
will not appear. This dialog box notifies the user that the Aircraft Manual is already installed and
deselecting these components will not uninstall them. Click the Yes button to continue.

Figure 103 - Components Exist dialog box (Manual)

Select Components page (Manual)

When only adding an Aircraft Manual to the collection, the user will select the Aircraft Manual
Only (new or update) item from the drop-down list. This selection will only check off the Aircraft
Manual box. Click on the Next button to continue.

- 64 -
Navigator Installation Guide

Figure 104 - Select Components page (Manual)

Components Exist dialog box (App)

If you are only adding an Aircraft Manual, then the Components Exist dialog box will appear.
Otherwise, this dialog box will not appear. This dialog box notifies the user that the Navigator
application is already installed and deselecting these components will not uninstall them. Click the
Yes button to continue.

Figure 105 - Components Exist dialog box (App)

Select Components page (App and Manual)

When only installing both the Navigator application and Aircraft Manual, the user will select the
Custom (manually select components) item from the drop-down list. This selection will check off
both the Navigator Application and the Aircraft Manual boxes. Click on the Next button to
continue.

- 65 -
Navigator Installation Guide

Figure 106 - Select Components page (App and Manual)

Select A Collection Folder page

Note: For the Browse to an Existing Navigator Application method, if you run the
NavigatorSetup.exe on its own, i.e. you are not running NavigatorSetup.exe from a Navigator
revision manual image folder, the Select A Collection Folder page will not appear during the
Setup process. Setup already knows you are installing the Navigator Application only.

You will only see the Select A Collection Folder page during Setup when you run the
NavigatorSetup.exe from a Navigator revision manual image folder. In the Select A Collection
Folder page, you can choose to install the Aircraft Manual only or install both the Navigator
Application and the Aircraft Manual. You can also choose to install the Navigator Application only
at this point.

The next page that appears is the Select A Collection Folder page. This page allows the user to
choose when collection folder (e.g. C:\navigator\collects) setup should install the Aircraft Manual.
You can type in the full path of the collection folder or you can click on the Browse button to
browse to the collection folder. Click on the Next button to continue.

- 66 -
Navigator Installation Guide

Figure 107 - Select A Collection Folder page

Ready to Install page

The next page that appears is the Ready to Install page. This page informs the user that Setup is
now Ready to Install the Navigator application. You can click on the Back button to review or
change any settings. Click on the Install button to begin installation of the Navigator application.

Note: The Ready to Install page screen shot below shows Setup is about to install the Navigator
Application only. The Ready to Install page will display different content that will look slightly
different if Setup is about to install an Aircraft Manual only or install both the Navigator
Application and Aircraft Manual.

Figure 108 - Ready to Install page

- 67 -
Navigator Installation Guide

Installing page

The next page that appears is the Navigator Installing page. This page performs the installation of
the Navigator application (along with the Integrator application) as it extracts the files from the
NavigatorSetup.exe file. Once the installation process is complete, Setup will take you to the next
page so you will not need to click on the Next button.

Figure 109 - Installing page

Information page

The next page that appears is the Navigator Information page. This page lists the History of the
Navigator application, what new features were added as well as changes made to the application.
Review the History file and click the Next button to continue. The History file (HISTORY.txt)
can be found in the doc folder of the Navigator application folder (e.g. C:\navigator\doc).

Figure 110 - Navigator Information page

- 68 -
Navigator Installation Guide

Completing the Bombardier Navigator Setup Wizard page

Note: The Completing the Bombardier Navigator Setup Wizard page screen shot below allows
the user to launch the Navigator Application once Setup is complete. This is also the case if you
are installing both the Navigator Application and Aircraft Manual.

If you are installing an Aircraft Manual only, then the Completing the Bombardier Navigator
Setup Wizard page will not allow you to launch the Navigator Application once Setup is
complete.

The final page in the process is the Completing the Bombardier Navigator Setup Wizard page. This
page tells the user that the installation process is finished.

If you are installing the Navigator application, you can Launch Bombardier Navigator by checking
off the box or you can leave the box unchecked if you do not wish to launch the application. Click on
the Finish button to exit the setup.

Figure 111 - Completing the Bombardier Navigator Setup Wizard page

- 69 -
Navigator Installation Guide

Navigator 1.5 Application Folder

Once you have installed Navigator 1.5, your Navigator 1.5 Application Folder should have the
following files. Please make sure that you are not missing any these files.

Figure 112 - Navigator 1.5 Application Folder

Integrator 1.5 Application Folder

Once you have installed the Navigator 1.5 application, you will also have installed its Integrator 1.5
application. The Integrator 1.5 Application Folder is located in the Navigator 1.5 Application Folder
(e.g. C:\navigator\integrator). Your Integrator 1.5 Application Folder should have the following files.
Please make sure that you are not missing any these files.

- 70 -
Navigator Installation Guide

Figure 113 - Integrator 1.5 Application Folder

Other Notable Messages

During the installation process, the user may encounter any one of the following messages
depending on the situation. Here are some of the messages that a user may encounter and how to
resolve the issue.

Navigator Application is not writable dialog box

If the user decides to re-install an existing Navigator application where the Navigator application is
read-only, then the following message will appear during the installation process. The user will
need to change the permissions for the Navigator application folder so that the folder is writable
and Setup will be able to complete the installation.

Figure 114 - The location is not writable dialog box

- 71 -
Navigator Installation Guide

Navigator Application is not available dialog box

If the user decides to re-install an existing Navigator application but the navigator.exe file is missing
from the Navigator application folder, then the following message will appear during the
installation process. The user will need to correct the problem and run setup again or choose
another Navigator instance or install a new Navigator instance.

Figure 115 - Navigator Application is not available dialog box

Setup cannot find navigator.ini dialog box

If the user decides to re-install an existing Navigator application but the navigator.ini file is missing
from the Navigator application folder, then the following message will appear during the
installation process.

Figure 116 - Setup cannot find the navigator.ini file dialog box

The user will need to create a new navigator.ini file to replace the missing navigator.ini file. The
user can add each individual entry with its default value into the new navigator.ini file.

Figure 117 - Navigator 1.5 navigator.ini file

- 72 -
Navigator Installation Guide

Uninstalling Navigator 1.5 and Integrator 1.5

Note: Integrator 1.5 no longer has its own uninstaller. Integrator 1.5 is now part of the
Navigator 1.5 uninstaller. This means when you uninstall a Navigator 1.5 instance, you will
automatically uninstall its Integrator 1.5 instance. The Integrator folder in the Start Menu does
not have an Uninstall Bombardier Integrator entry.

During the uninstall process, if the user forgets to close the Navigator application of the instance
that is currently being uninstalled, then some files in the Navigator application folder will not be
removed once the uninstall process is complete. The user can manually remove these files and
delete the Navigator application folder.

Before uninstalling, please make sure your Navigator application of the instance you are going to
uninstall has been closed. This allows the Uninstaller to perform a clean and complete uninstall of
the entire Navigator application.

Figure 118 - Integrator 1.5 folder (Start Menu)

Go into your Start Menu. Under Programs, select the Bombardier Navigator folder. In your
Bombardier Navigator folder, select Uninstall Bombardier Navigator.

Figure 119 - Uninstall Bombardier Navigator 1.5 (Start Menu)

- 73 -
Navigator Installation Guide

Once you have selected Uninstall Bombardier Navigator, the Bombardier Navigator Uninstall page
will appear. In this page, it asks you Are you sure you want to completely remove Bombardier
Navigator and all of its components? Click on the Yes button to begin the uninstall process. Click
on the No button will stop the uninstall process.

Figure 120 - Bombardier Navigator Uninstall dialog box

Navigator will run the Uninstall process to begin uninstalling Navigator 1.5 from your computer. The
Uninstall status will display Please wait while Bombardier Navigator is removed from your
computer while it is uninstalling the application. At this point, you cannot stop the uninstall
process.

Figure 121 - Bombardier Navigator 1.5 Uninstall status page

Once the Uninstall process is complete, the Bombardier Navigator Uninstall page will display the
message Bombardier Navigator was successfully removed from your computer. Click on the OK
button to complete the uninstall process.

Figure 122 - Bombardier Navigator 1.5 successfully uninstalled

- 74 -
Navigator Installation Guide

Customer Support

For technical support, please contact Bombardier Aerospace at [email protected]

- 75 -