User Guide

For Soundcraft Signature 16, 22 & 22MTK

 16, 22, 22MTK User Manual INFORMATION

INFORMATION

IMPORTANT
Please read this manual carefully before using your mixer
for the first time.

This equipment complies with the EMC directive 2004/108/EC and LVD 2006/95/EC.

This product is approved to safety standards:

IEC 60065:2005 (Seventh Edition) +A1:2005
EN60065:2006 +A1:2006 +A1:2008
UL60065 2012 7th Edition
CAN/CSA-E60065-03 + A1: 2006
And EMC standards
EN55103-1: 2009 (E2)
EN55103-2: 2009 (E2)

Warning: Any modification or changes made to this device, unless explicitly approved by Harman, will
invalidate the authorisation of this device. Operation of an unauthorised device is prohibited under Section
302 of the Communications act of 1934, as amended, and Subpart 1 of Part 2 of Chapter 47 of the Code of
Federal Regulations.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

* Reorient or relocate the receiving antenna.

* Increase the separation between the equipment and the receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.

For further details contact: Harman International Industries Ltd, Cranbourne House, Cranbourne Road, Potters Bar,
Hertfordshire EN6 3JN, UK. Telephone +44 (0)1707 665000 Fax: +44 (0)1707 660742 email: [email protected]

Harman International Industries Ltd. 2014. All rights reserved.

Parts of the design of this product may be protected by worldwide patents.
Part No. 5056808
Rev 1.1
E&OE September 2014

Soundcraft is a trading division of Harman International Industries Ltd. Information in this manual is subject to change
without notice and does not represent a commitment on the part of the vendor. Soundcraft shall not be liable for any
loss or damage whatsoever arising from the use of information or any error contained in this manual. No part of this
manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic,
electrical, mechanical, optical, chemical, including photocopying and recording, for any purpose without the express
written permission of Soundcraft.

Harman International Industries Limited

Cranborne House, Cranborne Road, Potters Bar, Hertfordshire, EN6 3JN, UK
Tel: +44 (0)1707 665000
Fax: +44 (0)1707 660742
http://www.soundcraft.com INFORMATION
 16, 22, 22MTK User Manual CONTENTS

CONTENTS

1.0 AN INTRODUCTION TO SIGNATURE 5.0: CHANNEL CONTROLS

1.0.1 The Signature Legacy 5.1: Input Controls

1.0.2 Sapphyre Asymmetric EQ
5.1.1: Mono Input Controls
1.1: Safety
5.1.2: Stereo Input Controls
1.2: Warranty
5.1.3: FX Return Controls
1.3: Specifications
5.2: Aux Master Controls

2.0: GETTING STARTED 5.3: Group Master Controls

2.1: Introduction To Consoles 5.4: Master Stereo Controls

2.2: Parts Of The Console

6.0: SOLO AND MONITORING

3.0: INPUTS AND OUTPUTS

3.1: Introduction to I/O
7.0: USB OPERATION
3.2: Console Inputs

3.3: Console Outputs 7.1: Signature 16, 22 USB

3.4: Other I/O 7.2: Signature 22MTK USB

4.0: CONSOLE ROUTING

8.0: LEXICON FX
4.1: Mono Input Channel
8.1: FX Control
4.1: Stereo Input Channel
8.2: Reverbs
4.3: FX Return Channel
8.3: Delays And Modulation
4.4: Aux Master Output

4.5: Group Master Output

4.6: Master Stereo Output APPENDIX 01: NO SOUND?

For clarity, this manual uses section references rather than page numbers. In some instances, one section reference
may extend to several pages.

CONTENTS
 16, 22, 22MTK User Manual 1.0: INTRODUCTION

INTRODUCTION TO SIGNATURE

Drawing on over 40 years experience in live sound mixing, the Signature Series combines a superb
analogue control surface with the unrivalled British sound of Soundcraft in a powerful, compact,
professionally specd mixer.
Built tough for trouble-free performance night-after-night, Signature Series mixers deliver great
sounding results thanks to high-grade Ghost preamps, the most musical EQ in the business, pristine
Lexicon effects and powerful dbx dynamics - all designed to let you discover your Signature sound.

Soundcraft Ghost Mic Preamps Award-winning Lexicon effects

Class-leading performance, with high headroom, wide dynamic Studio-grade Reverbs, Delays, Choruses and Modulations,
range and superb signal to noise ratio. designed to add a truly professional edge to your productions.
Soundcraft Sapphyre British EQ USB Digital Audio
Famed for its musical sound and unmistakable British quality USB digital I/O for direct connection to Digital Audio Worksta-
Soundcraft GB audio routing tions and digital systems. Signature MTK version adds Multi-
Track functionality.
Flexible pre/post switching on each Aux and subgroups with
powerful routing and switching options as well as dedicated Playback Channel Functions
outputs. Interval Mute fast switching of playback channel to main out-
dbx Limiters puts, plus in-dependant Pre/Post Aux switching.
High performance, high-ratio Compressors on selected input Built tough for the long haul
channels. Robust metal construction and premium-quality components:
Hi-Z instrument inputs Built to withstand the rigours of extensive use.
Switchable input stage, optimised for acoustic guitars, electric
guitars, and basses.
1.0: INTRODUCTION TO SIGNATURE
 16, 22, 22MTK User Manual 1.0.1: SIGNATURE LEGACY

SIGNATURE LEGACY

The Signature Series consoles bring musicality, creativity, and technical excellence together, thanks
not only to new technology and ideas, but also to a 40-year legacy of producing outstanding perfor-
mance tools. This console incorporate classic analogue designs, approved by Engineers.

Ghost pre-amps
The Soundcraft Ghost consoles ProMic
mic pre-amp is known for its ultra-low
noise and high headroom, making high
gain settings possible, without
compromising signal integrity.

Sapphyre British EQ
The Soundcraft Sapphyre console Asym-
metric EQ makes both creative and func-
tional tonal shaping of your signal simple
and intuitive. The EQ behaves differently
in cut and boost, making tonal adjust-
ments musical, and focusing cuts where
they are needed. See section 1.0.2 for
more detail.

GB Routing
The GB Console legacy is in Signatures
signal routing. There is pre/post switching
for all aux busses, plus flexible routing and
dedicated outputs for sub-groups.
See section 4 for more detail.

1.0.1: SIGNATURE LEGACY

 16, 22, 22MTK User Manual 1.0.2: SAPPHYRE EQ

SAPPHYRE EQ

Soundcraft Sapphyre Asymmetric EQ

The Soundcraft Signature console uses a special Asymmetric EQ first developed for the renowned
Soundcraft Sapphyre console. This EQ makes both creative and functional tonal shaping of your signal
simple and intuitive - an EQ that works the way music does.

The shelving bands of the EQ (LF and HF) use a slight boost at the EQs frequency when cutting,
and a slight cut when boosting.

For low frequencies, a slight cut when boosting prevents muddiness in he signal, while a slight boost when
cutting enables you to clean up the low end without losing precious punch and body of the signal. For the
HF shelf, a slight cut when boosting prevents harsh resonance at the EQs frequency, and a slight boost
before a cut can help maintain brightness while reducing HF.

The mid-bands (bell-shape) have a wide bandwidth (low Q) when boosting, and a narrower band-
width (high Q) when cutting.

The wide boost prevents prevent harsh resonances and tonal-changes that allow for a more pleasing and
musical EQ boost. The Narrow cut focuses on problematic frequencies, for getting rid of resonances, rings,
hums, and preventing feedback. If this was too wide you could remove too much body, creating a thin
sound.
1.0.2: SAPPHYRE EQ
 16, 22, 22MTK User Manual 1.1: SAFETY

INTRODUCTION > SAFETY

SAFETY NOTICES
For your own safety and to avoid invalidation of the warranty
please read this section carefully.

Important Symbols
Cautions
Alerts the user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompanying
the appliance.

Warnings
Alerts the user to the presence of uninsulated
dangerous voltage within the products
enclosure that may be of insufficient magnitude
to constitute a risk of electric shock to persons.

THIS UNIT MUST BE EARTHED

Under no circumstances should the mains earth be disconnected from the mains lead.

The wires in the mains lead are coloured in accordance with the following code:

Earth: Green and Yellow (Green/Yellow - US)

Neutral: Blue (White - US)
Live (Hot): Brown (Black - US)

As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals
in your plug, proceed as follows:

The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the
letter E or by the earth symbol.

The wire which is coloured Blue must be connected to the terminal in the plug which is marked with the letter N.

The wire which is coloured Brown must be connected to the terminal in the plug which is marked with the letter L.

Ensure that these colour codings are followed carefully in the event of the plug being changed.

This unit is capable of operating over a range of mains voltages as marked on the rear panel.

The internal power supply unit contains no user serviceable parts. Refer all servicing to a qualified service
engineer, through the appropriate Soundcraft dealer.

1.1: INTRODUCTION > SAFETY

 16, 22, 22MTK User Manual 1.1: SAFETY

INTRODUCTION > SAFETY

WARNINGS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Clean the apparatus only with a dry cloth.
Do not install near any heat sources such as radiators, heat resistors, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not block any ventilation openings. Install in accordance with the manufacturers instructions.
Do not use this apparatus near water.
Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. When the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When the cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
No naked flame sources, such as lighted candles or cigarettes etc., should be placed on the
apparatus.
No user serviceable parts. Refer all servicing to a qualified service engineer, through the
appropriate Soundcraft dealer.

It is recommended that all maintenance and service on the product should be

carried out by Soundcraft or its authorised agents. Soundcraft cannot accept any
liability whatsoever for any loss or damage caused by service, maintenance or repair
by unauthorised personnel.

WARNING: To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture. Do not expose the apparatus to dripping or splashing
and do not place objects filled with liquids, such as vases, on the apparatus. No
naked flame sources, such as lighted candles, should be placed on the apparatus.

Ventilation should not be impeded by covering the ventilation openings with items
such as newspapers, table cloths, curtains etc.

1.1: INTRODUCTION > SAFETY

 16, 22, 22MTK User Manual 1.1: SAFETY

INTRODUCTION > SAFETY

WARNINGS
ADVICE FOR THOSE WHO PUSH THE BOUNDARIES
Although your new console will not output any sound until you feed it signals, it has the
capability to produce sounds which, when monitored through an amplifier or headphones,
can damage hearing over time.

Please take care when working with your audio if you are manipulating controls which
you dont understand (which we all do when we are learning), make sure your monitors are turned
down. Remember that your ears are the most important tool of your trade, look after them, and they will
look after you.

Most importantly dont be afraid to experiment to find out how each parameter affects the sound
this will extend your creativity and help.

NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the inter-
ference at his own expense.

This Class B digital apparatus meets the requirements of the Canadian Interference-Causing
Equipment Regulations.

Cet appareil numrique de la Classe B respecte toutes les exigences du Rglement sur le matriel
brouilleur du Canada.

NOTE: The packaging, in which your console arrived, forms part of the product and must
be retained for future use.

1.1: INTRODUCTION > SAFETY

 16, 22, 22MTK User Manual 1.2: WARRANTY

INTRODUCTION > SAFETY

WARRANTY
1 Soundcraft is a trading division of Harman International Industries Ltd.
End User means the person who first puts the equipment into regular operation.
Dealer means the person other than Soundcraft (if any) from whom the End User purchased the Equipment, pro-
vided such a person is authorised for this purpose by Soundcraft or its accredited Distributor.
Equipment means the equipment supplied with this manual.

2 If within the period of twelve months from the date of delivery of the Equipment to the End User it shall prove
defective by reason only of faulty materials and/or workmanship to such an extent that the effectiveness and/or
usability thereof is materially affected the Equipment or the defective component should be returned to the Dealer
or to Soundcraft and subject to the following conditions the Dealer or Soundcraft will repair or replace the defec-
tive components. Any components replaced will become the property of Soundcraft.

3 Any Equipment or component returned will be at the risk of the End User whilst in transit (both to and from the
Dealer or Soundcraft) and postage must be prepaid.

4 This warranty shall only be available if:

a) The Equipment has been properly installed in accordance with instructions contained in Soundcrafts manual.
b) The End User has notified Soundcraft or the Dealer within 14 days of the defect appearing; and
c) No persons other than authorised representatives of Soundcraft or the Dealer have effected any replacement
of parts maintenance adjustments or repairs to the Equipment; and
d) The End User has used the Equipment only for such purposes as Soundcraft recommends, with only such
operating supplies as meet Soundcrafts specifications and otherwise in all respects in accordance Soundcrafts
recommendations.

5 Defects arising as a result of the following are not covered by this Warranty: faulty or negligent handling, chem-
ical or electro-chemical or electrical influences, accidental damage, Acts of God, neglect, deficiency in electrical
power, air-conditioning or humidity control.

6. The benefit of this Warranty may not be assigned by the End User.

7. End Users who are consumers should note their rights under this Warranty are in addition to and do not affect
any other rights to which they may be entitled against the seller of the Equipment.

1.2: INTRODUCTION > WARRANTY

 16, 22, 22MTK User Manual 1.3: SPECIFICATIONS

INTRODUCTION > SPECIFICATIONS

TYPICAL SPECIFICATIONS Operating Conditions

- Temperature Range: 5C to 40C
Frequency Response
- Mic / Line In to any Output: +/-1.5dB, 20Hz-20kHz Input & Output Levels
- Mic Input: +12.5dBu max
T.H.D. - Line Input: >+26dBu max
- Mono Mic Sensitivity -30dBu, Input level -16dBu, - Stereo Inputs: >+26dBu max
+14dBu @ Mix output: < 0.002% @ 1kHz - Mix Output: +21.5dBu max
- Stereo Mic Sensitivity -30dBu, Input level -16dBu, - Headphones (@150): 300mW
+14dBu @ Mix output: < 0.007% @ 1kHz
Input & Output Impedances
Noise - Mic Input: 1.2k
- Mono Mic Input E.I.N. (max gain): <-124dBu - Hi-Z Input: 968k
(150 source) - Line Input: 10k
- Stereo Mic Input E.I.N. (max gain): <-124dBu - Stereo Input: 21.5k
(150 source) - Outputs: 150 (balanced), 75 (unbalanced)

Crosstalk (@ 1kHz) USB Audio (16, 22)

- Channel Mute: >-90dB - Inputs/Outputs: 2-in, 2-out
- Fader Cut-off (rel +10 mark): >-90dB - Bit Depth: 16-bit, 24-bit
- Aux Send Pots Offness: >-82dB - Sampling rate: 44.1kHz / 48kHz / 88.2kHz / 96kHz /
176.4kHz / 192kHz
EQ (Mono inputs)
- HF: 12kHz, +/-15dB Multi-channel USB Audio (22MTK)
- HMF (swept): 400Hz 8kHz, +/-15dB - Inputs/Outputs: 24-in, 22-out
- LMF (swept): 80Hz 2kHz, +/-15dB - Bit Depth: 16-bit, 24-bit
- LF: .60Hz, +/-15dB - Sampling rate: 44.1kHz / 48kHz

EQ (Stereo inputs) Net Weight

- HF: 12kHz, +/-15dB - Signature 16: 8.66kg
- MF (swept): 140Hz - 3kHz, +/-15dB - Signature 22: 11.06kg
- LF: 60Hz, +/-15dB - Signature 22MTK: 11.36kg

Power Consumption Unit Dimensions (W H D)

- Signature 16: <80VA - Signature 16: 630mm x 595mm x 210mm
- Signature 22: <100VA - Signature 22: 750mm x 630mm x 210mm
- Signature 22MTK: <120VA - Signature 22MTK: 750mm x 630mm x 210mm

1.3: INTRODUCTION > SPECIFICATIONS

 16, 22, 22MTK User Manual 2.0: GETTING STARTED

GETTING STARTED - AN INTRODUCTION TO THIS MANUAL

Anyone with minimal audio experience should be able to operate the Soundcraft Signature console
without reading too much of this manual, though we do recommend you take the time to go through it.
An excellent place to start would be the feature list on the introductory page (section 1.0), which will
familiarise you with all of the main possibilities, facilities, and functions.

Please note: Most of the illustrations in this

manual are based on the Signature 22 console.
Where there are differences between operation
of Signature 16, 22, and 22MTK, it is noted in
the relevant section.

PDF For S
ound
If youre reading the PDF version craftof the manual,
Sign User
ature Guid
you can use the thumbnail view and links from
16, 2
2&2 e
2MT
the Contents page to navigate quickly. K

For clarity, this manual uses section references

rather than page numbers. In some instances,
one section reference may extend to several
pages.

2.0: INTRODUCTION TO THIS MANUAL

 16, 22, 22MTK User Manual 2.1: CONSOLE INTRO

GETTING STARTED > INTRODUCTION TO MIXING CONSOLES

The main function of a mixing console is to combine different audio inputs and independently adjust the levels
of those contributions to the mix. With this very basic functionality you can control and balance any kind of audio
from a one-man-band to an orchestra.

Most mixers however (including the Signature Series) offer far more than that. A variety of features allow the
operator to shape the mix, and use routing options to provide the additional conveniences used in audio mixing
applications, such as external effects sends, stage monitoring outputs, independent headphone monitoring, and
digital inputs and outputs.

Mix Faders
Faders make it easy to see and adjust relative levels. They allow you to visualise the mix.

Input Choice
All different microphones and instruments are catered for with mic, line, and Hi-Z input types / selections, in-
cluding 48V phantom power for powered (condenser / capacitor) microphones. The gain control allows you to
optimise the input level.

Equalisation
Examples include the high pass filter on an input to reduce unwanted low frequencies, or the three-band EQ
(Equaliser) used for tonal shaping of the source.

Dynamic Processing
This is audio processing that affects amplitude (volume). The Signature console includes a Limiter on selected
channels, which will prevent the input signal going too high, which would in turn cause distortion.

Output options
As well as mixing all the input (source) channel into one Master Stereo output, you can send particular
channels into additional group outputs, or create several different aux (auxiliary) mixes of all channels to send
to an FX (Effects) processor or stage monitor, for example. The headphone output allows the operator to listen
to the whole Main Mix, or to a selection of channels via the Solo System.

Solo / Monitor System

The solo system allows you to listen only to particular channels or busses through the headphones output, so
you can focus on a particular source without changing the mix.

Internal FX
FX (Effects) processing such as reverb, delay, chorus, phasing, and so on can be incorporated into a mixing
console so that you dont have to invest in outboard equipment or use up valuable physical inputs and outputs.
The Signatures Lexicon FX processing can be applied in a controlled manner by using the Auxiliary 3/FX mix
and the dedicated stereo FX return channel.

Digital inputs and outputs.

Digital I/O is necessary to work with digital audio systems and computer-based Digital Audio Workstations.
The Signature series uses a USB interface for either 2-channel input/output (main or Aux 1-2 output), or for
multitrack input and output (MTK versions) with the USB inputs able to individually replace the input channel
source for a flexible tape return path. For example, the MTK functionality could use DAW plug-ins as insert
processing on selected input channels, or you could do a sound check with a dry recording of the band from a
previous gig... There are lots of ways to use this feature.

More Information
You can find out more about individual Signature features by reading the relevant section of this manual.

2.1: INTRODUCTION TO CONSOLES

 16, 22, 22MTK User Manual 2.2: PARTS OF THE CONSOLE

GETTING STARTED > PARTS OF THE CONSOLE

The diagrams show different sections of the Signature console and describes those functions. After
that are more detailed descriptions of the console sections and references to the relevant chapters in
this manual.

2.2: Parts Of The Console

 16, 22, 22MTK User Manual 2.2: PARTS OF THE CONSOLE

GETTING STARTED > PARTS OF THE CONSOLE

Inputs & Outputs

The Signature console features a variety of physical inputs and outputs for getting audio in and out of the
console: XLR, Jack, and Phono for analogue audio I/O, and USB for digital audio. Refer to Section 3.0
for more detail, and to section 7.0 for detailed information on USB functionality. Note - USB functionality
for MTK (Signature 22MTK) and non-MTK (Signature 16 and 22) are different; both types are detailed in
section 7.0.

Mono Input Channels

Mono input channels control the levels, routing, and EQ on single channel audio inputs. All mono input
channels have both microphone and line-level capability. In addition, specific channels feature Hi-Z inputs
for high impedance sources such as guitar pick-ups. Refer to Sections 4.2 and 5.2 for more detail.

Stereo Input Channels

Signature 16, 22, and 22MTK consoles have two types of stereo inputs. One offers the option of a mono
microphone/line level input by using either the XLR or Left/Mono Jack Input as well as stereo Jack inputs;
the other (highest-numbered stereo channel) offers stereo line level phono inputs and is the Playback
Channel; the Master channels INTERVAL MUTE function mutes all channels except the Stereo playback
channel. Refer to Sections 4.3 and 5.3 for more detail.

FX Return

A Signature FX Return channel takes its input from the output of the internal Lexicon FX processor. It is a
stereo input channel with aux sends but without input level control or EQ. Refer to Sections 4.4 and 5.4 for
more detail.

2.2: Parts Of The Console

 16, 22, 22MTK User Manual 2.2: PARTS OF THE CONSOLE

GETTING STARTED > PARTS OF THE CONSOLE

Aux Output Masters

Aux (Auxiliary) Master output channels control the output level of the auxiliary bus and
global pre-fade/post-fader switching. AFL switching allows aux master solos. Refer to
Sections 4.5 and 5.5 for more detail.

Group Output Masters

The Group Output Master channels control routing and output level for the Group busses.
Groups 1 and 2, and 3 and 4 outputs can be summed to mono and/or routed to the Master
Stereo Output. Refer to Sections 4.6 and 5.6 for more detail.

Master Stereo Output

Controls the output level of the Master Stereo bus. Includes the Interval Mute function
(Mute all channels except the Stereo Playback Channel). Refer to Sections 4.7 and 5.7 for
more detail.

Metering
The meters show the monitoring selection level - Master Left/Right output level in normal
operation or the solo bus when a PFL or AFL is engaged. The AFL/PFL ACTIVE indicator is
below the main meters and lights when any AFl or PFL selection is engaged. See section
6.0 for more detail.

2.2: Parts Of The Console

 16, 22, 22MTK User Manual 2.2: PARTS OF THE CONSOLE

GETTING STARTED > PARTS OF THE CONSOLE

Lexicon FX Control
Signature 16 has a single internal Lexicon FX processor and
send/return bus for adding FX such as reverb, delay, Chorus,
Rotary, LoFi, Tape emulation, and more. Signature 22 and
22MTK have dual processors and send/return paths. Each
Effect has two adjustable parameters. Refer to section 8.0 for
more detail.

Power Indicator
Lights Green when console is powered. Power can be applied by connecting the power
cord. It is good practise to turn the output level down first in case this affects any connect-
ed speakers.

USB Power Socket

For attaching powered/chargeable USB peripherals such as a USB-powered LED lamp, or
a mobile phone. Not for data. There is a 500mA current limit on this connection.

Global Phantom Power Switch

Applies 48V phantom power to the console microphone inputs so you can use Condenser/
Capacitor
microphones, active DI boxes, and so on. See section 5.1 for more detail.

Headphones Level Control

Level control for the monitoring output - either the Master Stereo Output, or the Solo Bus.
See section 6.0 for more detail.

2.2: Parts Of The Console

 16, 22, 22MTK User Manual 3.0: INPUTS AND OUTPUTS

INPUTS AND OUTPUTS

The physical inputs and outputs on the Signature console are varied, and together with the Ghost mic
preamps, dbx limiting, and Hi-Z inputs provide a flexible scheme for any sources you might
encounter. To get the most out of the Signature I/O, read this chapter carefully.

3.0: INPUTS AND OUTPUTS

 16, 22, 22MTK User Manual 3.1: INTRO TO I/O

INPUTS & OUTPUTS > INTRODUCTION TO I/O

The Signature console offers a choice of industry standard audio inputs and outputs. All Jack and XLR
inputs are balanced. Below are some terms used in this manual and on the console labelling that may
be of use to you.

AUX (Auxiliary) Output Jack

An output bus made up of the summed Aux This is the long, quarter-inch connection most
contributions from input channels. In other commonly used on the signature console for
words, the AUX1 output will be a mix of all input line level inputs and outputs such as keyboards,
channel signals, with levels controlled by the external FX processors, playback and recording
AUX1 controls on the individual input channels. devices, and so on. All Signature-series Jack
Auxiliary mixes are used for many purposes - sockets are Tip-Ring-Sleeve 3-pole types. Jack
alternative mixes for monitoring, processing by outputs are impedance balanced.
external FX units, and more.
Line
Balanced For inputs and outputs this refers to a line level
A Balanced signal (Balanced Line) is one where signal. This is a higher voltage signal than mic
the signal is split between two conductors with level.
the same impedance / impedance to ground.
At a differential input, the differences between Mic
the two conductors are amplified, so any noise Microphone. For inputs and outputs this refers to
acquired between output and input is rejected a mic level input. This is a lower voltage signal
(common-mode rejection). than line level.

GRP (Group) MST (Master)

An output bus made up of the summed contri- Master Stereo Output: The main stereo Group
butions from any inputs routed to the Group. For output made up of the summed contributions
example, all inputs with their 1-2 buttons pressed from any inputs routed to MST with their MST
will be added to the GRP1 and GRP2 mixes. The buttons.
pan / balance control determines how the signal
is proportioned between the Group 1 and Group RCA
2 busses (Group 1 left, and Group 2 right). The small line-level connector commonly found
on consumer playback equipment. RCA inputs
Hi-Z are provided for the 15/16 (Signature 16) and
High Impedance. Guitar pick-ups generally have 21/22 (Signature 22 / 22MTK) stereo input
high impedance outputs and therefore require channels (Playback Channels).
a significantly higher than usual input imped-
ance when plugging them directly into a console USB - Universal Serial Bus
(straight from the guitar plug - not via an amp Standard serial data connection used by the
or a microphone). Hi-Z Inputs provide this. On Signature console for sending and receiving
the Signature console selected inputs have Hi-Z digital audio streams.
input switches to accommodate Hi-Z sources.
XLR
The round, three-pin connections. On the
Signature console they are used for microphone
inputs and the main stereo outputs.

3.1: INTRODUCTION TO I/O

 16, 22, 22MTK User Manual 3.2: CONSOLE INPUTS

INPUTS & OUTPUTS > CONSOLE INPUTS

Console inputs can be used for a wide variety of sources. For best results always use the appropriate
input connection.

Mic Input - XLR

Input connection for microphones using standard XLR connection (Pin-2 hot)
When using condenser microphones, you can switch on 48V phantom power for these connections on the right
hand side of the console (the 48V button). It's best practise not to use phantom power with unbalanced or instru-
ment inputs, switching it off BEFORE unplugging and switching it on AFTER plugging in.

Line Input - Jack

Balanced line-level connection for all other inputs
A Hi-Z option is provided on selected channels, required by high output impedance sources, such as guitar
pick-ups (when connecting a guitar directly to the mixer).

Line Input - RCA

Unbalanced input for line level/consumer playback equipment and instruments

3.2: CONSOLE INPUTS

 16, 22, 22MTK User Manual 3.3: CONSOLE OUTPUTS

INPUTS & OUTPUTS > CONSOLE OUTPUTS

The console outputs offer a range of connection options depending on the application. Always
consider carefully the best output and routing strategy for your particular application.

MST L / MST R
Master Left and Right outputs, XLR connectors
These are impedance-balanced line level outputs (pin 2 signal). The XLR outputs are labelled 'MST L' and MST R',
which refers to Master Left and right outputs of the main stereo output. These should be connected to the input
of your amplifier, PA system, recorder, or similar.

AUX 1 / AUX 2 / AUX 3

Auxiliary output connectors - quarter-inch Jack
Line level output, TRS Jack. Impedance balanced.

HEADPHONES
Stereo headphone output - quarter-inch TRS Jack
The headphone signal is always the Master Stereo Output unless a Solo (PFL or AFL) is activated. In that case, the
headphone output is switched to the Solo Bus.

GRP 1 / GRP 2 / GRP 3 / GRP 4

Group 1, 2, 3, and 4 outputs - Quarter-inch Jack
Line level output, TRS Jack. Impedance balanced.

3.3: CONSOLE OUTPUTS

 16, 22, 22MTK User Manual 3.4: OTHER I/O

INPUTS & OUTPUTS > OTHER I/O

The console outputs offer a range of connection options depending on the application. Always
consider carefully the best output and routing strategy for your particular application.

USB - Signature 16 and 22

USB data connection for audio input and output
USB input (USB channels 1 and 2) are summed with the RCA input signal on the highest-numbered stereo input
channel. The USB output is taken either from the Master Stereo output (MST) or the Aux 1-2 output (according to
selector switch next to USB connector). For more detail on this feature, please see section 7.

USB - Signature 22MTK (24 Track I/O)

USB data connection for audio input and output
The Signature MTK (MultiTrack) console uses the USB port to send post gain direct outputs from all input chan-
nels and optionally return those channels to the same input channel. This is, in effect, a USB insert or tape return
path for all input channels. USB output channels 23 and 24 are used for the Master Stereo (MST) output. For
more detail, please see section 7.

USB POWER
For attaching powered/chargeable USB peripherals
Examples include a USB-powered LED lamp, or a mobile phone. Not for data. This connection supplies USB 2.0
compliant 500mA. Devices that draw more than this amount should not be connected.

FOOTSWITCH
Connect a TRS foot switch for FX Mute functionality
Various foot switches are available, depending on the specific functionality you require. Connecting Tip and Ring
('Make') will mute the internal FX.

Power
A standard IEC60320 C14 male plug for use with a C13 female plug
Rated at 110 - 240V, 50Hz-60Hz. The Power connector is located on the underside of the Signature console.

3.4: OTHER I/O

 16, 22, 22MTK User Manual 4.0: CONSOLE ROUTING

CONSOLE ROUTING

Understanding the facilities a console offers for routing and controlling audio is an important step in
learning how to operate the console most effectively.

This Section uses simple flow diagrams and short descriptions to describe the various signal paths
and routing options for all channel and bus types. If you have never operated a similar console before,
it is worth digesting all these options before you use the console in a critical application.

Signals generally flow through the console from an input channel, then as a mix onto a bus (Aux,
Group, Stereo, Solo), and through an output master (Master Stereo Output, Group Master Output, Aux
Master Output, Monitor / Headphones Output.

For more basic descriptions of the main routing functions, see section 2.1: Introduction To Consoles.

4.0: CONSOLE ROUTING

 16, 22, 22MTK User Manual 4.1: MONO INPUT

CONSOLE ROUTING > MONO INPUT

All mono input channels

have the choice of XLR
(mic) and Jack (Line)
balanced inputs; the
two highest numbered
mono channels have
Hi-Z input switches for
the line inputs while
channels 1 and 2
incorporate switchable
input limiters.

All Mono input channels

can contribute to Aux 1,
Aux 2, Aux 3, Aux 4/FX,
Aux 5/FX (on Signature
22/22MTK), MST (Mas-
ter Stereo), the Solo
bus, and Groups 1-4.

Like the Master

Stereo bus contribution,
Group contributions are
sent post-pan/balance
(odd-numbered groups
are left, even-numbered
groups are Right).

4.1: MONO INPUT ROUTING

 16, 22, 22MTK User Manual 4.2: STEREO INPUT

CONSOLE ROUTING > STEREO INPUT

There are two types of

Stereo input channel.

The lower-numbered
stereo input channels
have microphone
inputs and Jack inputs
and can be used as
mono input channels
(odd-numbered input) if
required. On Signature
22 and 22MTK Stereo
channel 19/20 doesnt
have a mic input.

The highest-numbered
Stereo input is a sum of
the line level R inputs
and the stereo USB
input (if present). This
is the playback channel
and works with the
INTERVAL MUTE
function for convenient
2-track playback
functionality.

Stereo input channels

have the same routing
options as mono input
channels. Aux bus
contributions from
stereo channels are
made from a sum of the
left and right signals.

Group bus contribu-

tions are balanced /
panned left and right
to the corresponding
odd-numbered and
even-numbered group
respectively. In other
words - fully left would
be fully Group 1 or
Group 3.

4.2: STEREO INPUT ROUTING

 16, 22, 22MTK User Manual 4.3: FX RETURN

CONSOLE ROUTING > FX RETURN

An FX Return channel is a special stereo input channel is fed from the output of the internal FX
processor.

An FX Return channel can contribute to any Aux bus (EXCEPT its own source), and to the Master
and Group busses - as per mono and stereo input channels. Signature 22 and 22MTK consoles have
two FX Return channels as those consoles have two internal FX processors.

4.3: FX RETURN ROUTING

 16, 22, 22MTK User Manual 4.4: AUX MASTER

CONSOLE ROUTING > AUX MASTER

Aux busses sent directly out of the corresponding Aux outputs, and are globally switchable between
pre- and post-fade sources. That is, an Aux mix that is taken pre-fade (before the input channel
fader) is not affected by the input channel fader levels. An Aux mix taken post-fade (after the input
channel fader) will be based on the fader levels of the contributing input channels.

The Playback Channel (highest-numbered stereo input) Aux 1 and 2 sends can be individually
switched post-fader. This is useful where, for example, the Aux 1/2 outputs are being used for pre-
fade stage monitors. By switching the playback (incidental of interval music for example) to post-fad-
er, musicians will be able to hear the playback music when it is faded up, and still allow the console
operator to hear the channel on PFL without it being heard in a monitor.

Aux Masters can contribute to the Solo bus (AFL). See section 6 for more details.

4.4: AUX MASTER ROUTING

 16, 22, 22MTK User Manual 4.5: GROUP MASTER

CONSOLE ROUTING > GROUP MASTER

The Group Master Outputs are derived from the post fade, post pan sum of input channels routed to
the corresponding Group busses (1-2 and 3-4 switches).

The Group Masters can contribute to the Master Left/Right Bus.

A useful example of this in practise might be where a group of related input channels (drum mics,
backing singers, and so on) are mixed relative to each other, then routed to GRP 1-2 (but not to
MST). If the Group Masters are then in turn routed to the Master Left/Right output you can adjust the
level of the whole group within the main mix by using the Group 1 and 2 faders.

4.5: GROUP MASTER ROUTING

 16, 22, 22MTK User Manual 4.6: MASTER STEREO OUTPUT

CONSOLE ROUTING > MASTER STEREO OUTPUT

The Master Stereo output is derived from contributions to the Master (MST) Stereo Bus. You can
choose to route input channels to the Master Stereo Bus using the input channel MST buttons.

4.6: MASTER STEREO OUTPUT ROUTING

 16, 22, 22MTK User Manual 5.0: CHANNEL CONTROLS

CHANNEL CONTROLS

There are three types of Signature console input channels: Mono Input, Stereo Input, and FX Return.
The output channel types are the Auxiliary (Aux) Master Outputs, the Master Stereo Outputs, and the
Group (GRP) Master Outputs.

5.0: CHANNEL CONTROL

 16, 22, 22MTK User Manual 5.1: INPUT CONTROLS

CHANNEL CONTROLS > INPUT CONTROLS

Input channels take sources and route/process them. The sources catered for by the Signature
consoles includes mono (single channel) sources, stereo sources, and internal sources (the FX Return
channel).

The controls are shown in

the order they appear on
the console channel
strip - from top to bottom.
This is not necessarily
signal path order. Please
refer to the relevant signal
path diagram (section 4).

Controls common to all

input channel types are
documented in the Mono
Input Channel controls
section (5.1.1). Controls
or explanations specific to
Stereo input channels and
the FX Return Channels
are documented in those
sections (5.1.2 and 5.1.3
respectively).

5.1: INPUT CONTROLS

 16, 22, 22MTK User Manual 5.1.1: MONO INPUT CONTROLS

CHANNEL CONTROLS > MONO INPUT CONTROLS

PHANTOM POWER 48V

Apply a DC voltage of 48V to all microphone inputs
This button is found on the right of the console near the headphones level control, not on the channel strip.
With phantom power on, you should use only balanced sources in the console's XLR microphone inputs. Balanced
dynamic microphones (for example) will be unaffected. Condenser microphones normally require phantom
power, and it is sometimes used to power active circuitry in other devices, such as DI boxes.

LIMITER
Activate the input limiter
The Signatures dbx Limiters uses fixed time constants and threshold with high-ratio compression to tame signal
peaks and prevent audio clipping. You can purposefully drive the limiter by turning up the Gain until the limiter
LED lights. The Limiter button LED lights when gain reduction is applied.

GAIN REDUCTION LED

Lights when the Limiter is applying gain reduction
When the Limiter applies gain reduction, the LED will light. The LEDs light will become more intense as more gain
reduction is applied.

HI-Z
Switch the line (Jack) input to 'Hi-Z' (high impedance) mode
Activating Hi-Z presents a much higher load impedance to the source in order to work more effectively with
high-impedance sources such as guitar, bass, and other instrument pick-ups that are connected directly to the
console. Using the standard Z mode on high impedance sources will have a detrimental effect on the high
frequency response.

GAIN
Adjust the input gain
The Gain range is 10dB to 60dB. It is advisable to listen and/or to check the channel Peak LED while increasing
gain to avoid distortion due to clipping. Before plugging in a new source, turn the Gain down to avoid sudden
loud noises.

5.1.1: MONO INPUT CONTROLS

 16, 22, 22MTK User Manual 5.1.1: MONO INPUT CONTROLS

CHANNEL CONTROLS > MONO INPUT CONTROLS

HPF 100Hz
Activate the High Pass Filter
The High Pass Filter (HPF) is an 18dB/Octave filter that attenuates frequencies below 100Hz. This can be useful for
filtering out low 'rumble' from microphones affected by extremely low traffic noise, air flow, and so on.

USB RTN (22MTK only)

Enable the USB Return function
When active, the audio on USB channel 'n' (where 'n' is the console channel number) will replace the analogue
inputs post-gain (pre HPF / EQ) and the analogue audio path will be broken. Please see section 7 for more details.

HF
Adjust the boost/attenuation of the high frequency shelving filter
The HF shelving filter has a fixed frequency of 12kHz. Frequencies above this will be boosted or attenuated
depending on the control setting. With this Sapphyre asymmetric EQ, there is a small boost at the filter frequency
on cut and a small cut on boost. See section 1.02 for more detail.

HMF/LMF Frequency
Adjust the centre frequencies of the High-Mid and Low-Mid bell-type filters
The Signature HMF and LMF EQ bands are bell-type, semi-parametric filters. This control adjusts the centre fre-
quency of those bell shapes between 400Hz (approximately G3) and 8kHz (approximately B8) for the HMF Filter,
and between 80Hz (approximately D#1) and 2kHz (approximately B6) for the LMF filter.

HMF/LMF Level
Adjust the boost/attenuation of the High- and Low-Mid bell-type filters
This will adjust the gain or attenuation of the audio band, centred according to the corresponding frequency con-
trols. This is an asymmetric EQ, so boost has a wide bandwidth (low Q), and cut has a narrow bandwidth (High
Q). See section 1.0.2 for more detail.

5.1.1: MONO INPUT CONTROLS

 16, 22, 22MTK User Manual 5.1.1: MONO INPUT CONTROLS

CHANNEL CONTROLS > MONO INPUT CONTROLS

LF Level
Adjust the boost/attenuation of the low frequency shelving filter
The LF shelving filter has a fixed frequency of 60Hz. Frequencies below this will be boosted or attenuated
depending on the control setting. With this Sapphyre asymmetric EQ, there is a small boost at the filter frequency
on cut and a small cut on boost. See section 1.02 for more detail.

AUX1 / AUX2 / AUX3

Adjust the level of this channel's contribution to the Aux 1, Aux 2, and Aux 3 busses
An Auxiliary bus is a summed 'alternate' mix of any contributing channels. In other words - for example - the
console's Aux 1 output will consist of all channels whose Aux 1 controls are greater than -infinity (off) - mixed pro-
portionally according to the relative levels of all the Aux 1 controls. You could use this for a stage monitor mix, or a
'send' to an external FX processor, for example. The source for the Auxiliary bus send can be either post-fader or
pre-fade, as set by the button in the Auxiliary Masters section.

AUX4/FX, AUX5/FX
Adjust the level of this channel's contribution both to the Aux bus (as per Aux 1, 2, and 3), and the
Internal FX processor.
Signature 22 and 22MTX consoles have two internal FX processors and therefore have an additional Aux/FX send
(Aux5/FX). The Aux 4 bus and the FX bus (also Aux 5 / FX 2 busses for signature 22 / 22MTK) are independent,
but share the same Send level. The source for an FX bus send is always post-fader so that a sources contribution
to an effect is proportional to its contribution to the mix. The Aux source can be switched Pre or post (as per
normal Aux send).

PAN
Adjust the signal's stereo position and group routing.
Pan determines both the signal's position on the Master (MST) Stereo output and the amount of signal sent to
odd-numbered (left) and even-numbered (right) group outputs. For example, with a channel's 1-2 and MST
routing switches engaged, turning the control right puts more of the signal in the right (MST) channel AND
the Group 2 bus. Turning the control fully right will route the signal fully to the right-hand master channel AND the
Group 2 bus.

MUTE
Mute the signal
This is a pre-fade mute and so does not affect the USB send on the Signature 22MTK console. However, it will
mute all Aux bus contributions, as well as Master Stereo and Group contributions. When a channel is muted, the
Peak & Mute LED will light.

5.1.1: MONO INPUT CONTROLS

 16, 22, 22MTK User Manual 5.1.1: MONO INPUT CONTROLS

CHANNEL CONTROLS > MONO INPUT CONTROLS

PEAK & MUTE LED

Lights when signal reaches peak level or shows that the channel is muted
The Peak LED is a warning light to let you know when the signal is nearing maximum headroom. The peak
detection source is taken from a number of key points in the signal path (see section 4.1) where gain is used: After
the High Pass Filter, post EQ, and post Fade. If a signal is amplified past the limits of the console's headroom, then
'clipping' (noise) will occur.

PFL
Route the signal to the Solo bus and mute any channels not routed to the Solo bus
With a PFL enabled, the headphone output will switch to the Solo Bus. Please see section 6 for more detail.

FADER
Adjust signal level
The Fader adjusts level between -infinity (no signal) to +10dB. The 0dB line indicates unity (no level change).
Faders are the primary mixing tools during performance; the relative levels of the input channel faders across the
console determine the Master Stereo (MST) and Group (GRP) mixes, as well as providing the source for post-fade
Aux mixes.

GRP 1-2 / 3-4

Route the channel output to Group busses
The channel's PAN control determines the proportion of the signal across group pairs.

MST
Route the channel output to the Master left/right bus
The Pan/Balance controls proportion the signal to the left and right Master bus channels.

5.1.1: MONO INPUT CONTROLS

 16, 22, 22MTK User Manual 5.1.2: STEREO INPUT CONTROLS

CHANNEL CONTROLS > STEREO INPUT CONTROLS

There are two types of Signature Stereo Input Channels. The normal type has two jack inputs,
normalised so that a single jack or microphone input will operate as a mono input channel (Balance
becomes Pan). NOTE: Controls common to all input channel types are shown in the Mono Input Chan-
nel control list - 5.1.1

TRIM
Adjust the input level (highest-numbered stereo channel only)
This gives a adjustment range suitable for the typical stereo line-level source for this channel, such as a consumer
playback device.

Aux 1, 2, 3, 4/FX, 5/FX.

Adjust the level of this channel's contribution to the Aux send busses.
The Aux controls on a stereo input channel work in the same way as for a mono input channel. Please note, how-
ever - a stereo input channel's contribution to an auxiliary bus is a mono sum of the channel's left/right signals

AUX 1-2 PRE/POST

Switch Aux 1 and 2 sources post- fader for the Playback Channel only
The highest-numbered stereo input channel Aux 1 and 2 sends can be individually switched post-fader. This is
useful where, for example, the Aux 1/2 outputs are being used for pre-fade stage monitors. By switching the
playback (incidental of interval music for example) to post-fader, musicians will be able to hear the playback
music when it is faded up, and still allow the console operator to hear the channel on PFL without it being heard
in a monitor.

PAN/BAL
Adjust Pan or Balance (stereo position or relative Left/right levels)
When the stereo input channel is being used as a mono input channel (no Jack in the channel's Right input), the
Pan/Balance control acts as a Pan control (levels to left and right or odd/even groups proportional to the control's
position), which will change the stereo position of the single source. Otherwise, the control is a Balance control,
which adjusts the relative levels of the left and right signals - effectively adjusting the left-right position of the
overall stereo image.

5.1.2: STEREO INPUT CONTROLS

 16, 22, 22MTK User Manual 5.1.2: STEREO INPUT CONTROLS

CHANNEL CONTROLS > STEREO INPUT CONTROLS

BAL
Adjust stereo balance for this channel
Adjusts the relative levels of the left and right signals for this channel, effectively adjusting the left-right position
of the overall stereo image across the Master Stereo Bus and odd/even Group pairings - according to routing
selections.

GRP 1-2 / 3-4

Route the channel output to Group busses
The channel's PAN/BAL or BAL control determines the proportion of the signal across group pairs.

5.1.2: STEREO INPUT CONTROLS

 16, 22, 22MTK User Manual 5.1.3: FX RETURN CONTROLS

CHANNEL CONTROLS > FX RETURN CONTROLS

A stereo FX Return channel is fed from the output of its internal

FX processor. The Signature 16 has one FX Return channel and
one FX processor. The Signature 22 and 22MTX have two. The
FX Return channel is a cut-down version of the normal stereo
channel, without trim, EQ, or an Aux send path back to its own
processors send bus (FX Return 1 does not have an Aux4/FX
send).

An example in use might be running a Reverb algorithm in the

processor (FX 1 for Signature 22 and 22MTX). Each individual
channels Aux 4/FX control will control how much of that source is
present in the reverberant field generated by the processor; the
FX return fader will then control the level of that whole reverberant
field in the mixes it is routed to (Main Stereo Bus, Group 1-2, 3-4).

FX send is always post-fade so an input channels contribution

to that reverberant field will be proportional to that channels
contribution to a mix.

BAL
Adjust stereo balance for this channel
Adjusts the relative levels of the left and right signals for this channel, effectively adjusting the left-right position
of the overall stereo image when routed to MST. The balance is also adjusted across group pairs when the channel
is routed to groups 1-2 or 3-4.

GRP 1-2 / 3-4

Route the channel output to Group busses
The channel's PAN/BAL or BAL control determines the proportion of the signal across group pairs.

5.1.2: FX RETURN CONTROLS

 16, 22, 22MTK User Manual 5.2: AUX MASTER OUTPUT

CHANNEL CONTROLS > AUX MASTER OUTPUT

The Aux Master Output channel determines the output level of a whole Aux mix (the sum of all
Aux contributions). That is, the Aux 1 Master controls the Aux 1 output level, which is the sum of
all Aux 1 contributions from the input channels.

AUXn MST
Adjust the level of the Aux mix output for the corresponding Aux bus

AUXn PRE/POST
Globally switch Aux sources from input channels between pre- and post-fade
Determines whether the Aux mix is affected by the input channel fader positions or not. Note that the
Stereo Playback channel has independent pre/post switching for Aux 1 and 2.

AFL
Route the signal to the Solo bus and mute any channels not routed to the Solo bus
With an AFL enabled, the headphone output source will switch to the Solo Bus. Please see section 6 for
more detail.

5.2: AUX MASTER OUTPUT

 16, 22, 22MTK User Manual 5.3: GROUP MASTER OUTPUT

CHANNEL CONTROLS > GROUP MASTER OUTPUT

Group Masters control the Group output levels and

routing.

Signature 16, 22, and 22MTK consoles have four group

masters available (post-fader) - with mixes derived
from any input channel routed to GRP 1-2 or 3-4. Input
channel panning or balance positions work across
group pairs - odd-numbered groups are left (1, 3) and
even-numbered groups are right (2, 4).

MONO
Switch both Group-to-MST outputs to mono
Where a Group is routed to the Master left/right output, that contribution is derived from the sum of both Group
busses. The physical Group outputs remain separate.

MST
Route the Group output to the Master Stereo mix in addition to the physical Group Outputs
Groups 1 and 3 go to the Left and Groups 2 and 4 Go to the right unless the Group Master MONO button is
pressed.

FADER
Adjust the overall output level of the Group
Each group has its own fader for overall level control.

5.3: GROUP MASTER OUTPUT

 16, 22, 22MTK User Manual 5.4: MASTER STEREO OUTPUT

CHANNEL CONTROLS > MASTER STEREO OUTPUT

The Master (MST) Stereo Output channel determines

the output level of the main stereo (left and right) mix
from the MST L and MST R physical outputs.

Input channels must be routed to the Master Stereo

Output with their MST buttons.

INTERVAL MUTE
Mute all channels except Stereo Playback channel 15/16 (Signature 16) or 21/22 (Signature
22/22MTK)
A fast way of switching to only the interval or playback source, or similar, without touching any other controls.
Connect the playback device to the Stereo Playback channel (highest numbered stereo channel, RCA inputs).
Engage the INTERVAL MUTE switch when required. All other channels are muted. NOTE: Aux and Group outputs
are still active.

FADER
Adjust the overall level of the Master Stereo output

5.4: MASTER STEREO OUTPUT

 16, 22, 22MTK User Manual 6.0: SOLO AND MONITORING

SOLO AND MONITORING

Being able to monitor sources individually is an important tool for the Mix Engineer. PFL allows you to
check sources from stage without changing the mix, while AFL allows you to refine Auxiliary Monitor
and FX send mixes.

The Signatures Solo and monitoring system allows an engineer to hear either the Master (MST)
stereo outputs or any channels currently assigned to the Solo bus, via the headphone output.

Pressing a PFL button on an input channel sends that source, pre-fade (pre-mute, post EQ) to the
Solo Bus and switches the Headphone outputs source to the Solo bus.

Pressing an AFL button on an Aux Master output channel sends that source, post-fade (after the Aux
Master level control) to the headphones.

AFL and PFL selections are cumulative. That is, pressing more than one PFL or AFL button will add
that source to the Solo bus. Only when no PFL or AFL buttons are engaged will the headphone
output source revert to the Master Left/Right Output (MST).

6.0: SOLO AND MONITORING

 16, 22, 22MTK User Manual 6.0: SOLO AND MONITORING

SOLO AND MONITORING

PFL
Enable the Pre-Fade Listen function
Send this input channel's signal to the Solo Bus - A pre-fade, pre-mute, post EQ signal tap. An active PFL (or AFL)
switches the headphone output source to the Solo Bus. Active PFL button red indicator LEDs show active PFLs.

AFL
Switch the After-Fader Listen function
Send this Auxiliary Master output's signal to the Solo bus from a post-fade tap and switch the headphone
output source to the Solo bus.

PHONES LEVEL
Adjust the level of the headphone output
The headphone output will either be the Master Stereo Output (default) or the Solo bus - if a Solo is active.

BARGRAPH METERING
Bargraph display of current monitoring (headphones) signal
If a Solo (PFL or AFL) is active then - just like the headphone output - meters will display Solo bus levels.
Otherwise they display the Master Stereo bus levels.

PFL/AFL LED
Lights when a PFL or AFL is active
Any active solo will cause this LED to light up. Leaving a Solo on is a common cause of monitoring problems.
Check this LED if the monitoring output is not as expected.

6.0: SOLO AND MONITORING

 16, 22, 22MTK User Manual 7.0: USB OPERATION

USB OPERATION

The Soundcraft Signature consoles use USB 2.0 audio streaming for sending and receiving digital
audio. The Signature 16 and 22 consoles have a two-track USB system while the Signature 22MTK
(Multi-Track) uses a 22-channel system for channel direct inputs and outputs, plus a two-channel sys-
tem for the Playback Channel and recording the recording the main LR mix.

7.0: USB OPERATION

 16, 22, 22MTK User Manual 7.1: SIGNATURE 16, 22 USB

USB > SIGNATURE 16, 22

The Signature 16 and 22 consoles have 2-track USB input and output functionality. This could be used
for recording a mix to a PC or Tablet, for example - or to use a computer as a playback device.
Channels 1 and 2 are received by the Stereo Playback Channel (15/16 for Signature 16, 21/22 for
Signature 22).

There are two USB Send (output) options - to send either the Master Stereo (MST) output, or the Aux
1 and 2 outputs. These are sent on USB output channels 1 and 2.

USB I/O
A USB Standard-B Plug for USB data connection
The USB connector above the highest-numbered stereo channel is for audio data connection. Please note, the
USB Standard-A plug next to the PHANTOM POWER switch is for powering USB devices only (charging devices,
USB-powered lamps, and so on).

USB SEND
Choose USB Send mode
When this switch is depressed, the Aux 1 and Aux 2 bus outputs will be output on USB channels 1 and 2 respec-
tively - so that Aux 1 and 2 controls can be a dedicated USB mix. Otherwise the console outputs the Master Left
and Right outputs on USB channels 1 and 2 respectively.

7.1: SIGNATURE 16, 22 USB

 16, 22, 22MTK User Manual 7.2: SIGNATURE 22MTK USB

USB > SIGNATURE 22MTK

Signature MTK: Multi-Track USB

Input channels always send direct outs to the
corresponding USB channels. USB RTN buttons
activate the return for that channel so you can
use it as a DAW return, insert point, or virtual
soundcheck.

The Signature 22MTK console also has Multi-Track (MTK) output and input functionality that allows
sending of direct outputs from the input channels and return USB audio channels directly to the input
channels.

This makes it easy to set up multi-track recording and monitoring to and from a computer-based DAW,
for example; or to run a virtual soundcheck from a previously recorded show.

Multi-Track channels are numbered according to Input Channel numbers, so Signature input channels
1-22 use USB audio channels 1-22.

The Signature 22MTK Input channels ALWAYS send their post-gain, pre-EQ signal to their respective
USB recording channel.

The 2-track (Master Left/Right) output uses USB channels 23 and 24 and is always active.

MultiTrack USB input is selectable per-channel with the USB RTN button. When pressed, the USB
input channel corresponding to the Signature channel is replaces the normal audio input for that
channel (just after the USB output tap: post-gain, pre-EQ).

7.2: SIGNATURE 22MTK USB

 16, 22, 22MTK User Manual 7.2: SIGNATURE 22MTK USB

USB > SIGNATURE 22MTK

USB I/O
A USB Standard-B Plug for USB data connection
The USB connector above the highest-numbered stereo channel is for audio data connection. Please note, the
USB Standard-A plug next to the PHANTOM POWER switch is for powering USB devices only (charging devices,
USB-powered lamps, and so on).

USB RTN
Press to use the USB return-path for this channel
The USB audio channel corresponding to the input channel number will be used instead of the normal channel
input. The red LED indicator on the button will light to show that the function is active.

NOTE: The analogue input to an input channel will ALWAYS be SENT via the corresponding USB audio channel, so
you can use a USB SEND > DAW > USB RTN path to insert DAW-based plug-ins into the mixers channel path.

7.2: SIGNATURE 22MTK USB

 16, 22, 22MTK User Manual 8.0: LEXICON FX

LEXICON FX

The Signature 16 console has one internal FX processor, and the Signature 22 and 22MTK consoles
have two (FX 1, FX 2) - with dedicated internal send and return routing. There are 22 different FX
algorithms available, each with two adjustable parameters mapped to the PARAM 1 and PARAM 2
controls.

For FX 1, Aux 4/FX Sends control input channel contributions to both the FX processor and the Aux 4
output. For FX 2 (Signature 22 and 22MTK only), Aux 5/FX Sends control input channel contributions
to both the FX 2 processor and the Aux 5 output.

An FX Return channel is a hard-wired stereo return channel for the output of the FX processor.
Signature 22 and 22 MTK consoles have two FX Return channels - one for each processor.

8:0 LEXICON FX
 16, 22, 22MTK User Manual 8.1 FX CONTROL

LEXICON FX > FX CONTROL

Because an Internal FX processor has fixed routing, operation is very simple.

To use the FX, simply turn up an active input channels Aux/FX send control; with the FX TYPE encod-
er select an appropriate algorithm and press the encoder to activate; push up the FX Return channel
fader. You must ensure that the FX Return output routing is correctly for the application - MST / GRP
1-2 / GRP 3-4.

PARAM 1 / PARAM 2
Adjust FX parameters mapped to these controls
Different FX algorithms require different parameters for control. When you select a new algorithm, those
parameters are assigned to the PARAM 1 and PARAM 2 controls. For a list of the parameters used for different
algorithms, please see section 8.2.

FX TYPE
Select an FX algorithm (Press to activate)
The selected algorithm will be highlighted in white and loaded upon pressing the encoder. PARAM 1 and PARAM
2 encoders will be assigned to the appropriate FX parameters. Please see section 8.2 for more detailed algorithm
descriptions.

8.1: FX CONTROL
 16, 22, 22MTK User Manual 8.2: REVERBS

LEXICON FX > REVERBS

Reverberation (or reverb for short) is the complex effect created by the way we perceive sound in an
enclosed space. When sound waves encounter an object or boundary, they dont just stop. Some of
the sound is absorbed by the object, but most of the sound is reflected or is diffused. In an enclosed
space, reverb is dependent on many features of that space, including the size, shape and the type of
materials that line the walls. Even with closed eyes, a listener can easily tell the difference between a
cupboard, a locker room and a large auditorium. Reverb is a natural component of the acoustic
experience, and most people feel that something is missing without it.

ROOM
Room produces an excellent simulation of a small room which is useful for speech applications. Room is also prac-
tical when used judiciously for fattening up high energy signals like electric guitar amp
recordings.

Parameter 1: Liveliness
Parameter 2: Decay Time

PLATE
The plate reverb algorithm simulates the original plate reverb effect - a large, thin sheet of metal suspended
upright under tension on springs. Transducers attached to the plate transmit a signal that makes the plate vibrate,
causing sounds to appear to be occurring in a large, open space. Plate reverbs are designed to be heard as part
of the music, mellowing and thickening the initial sound. Plate reverbs are often used to enhance popular music,
particularly percussion.

Parameter 1: Liveliness
Parameter 2: Decay Time

ROOM MOD
A modulated room reverb. Modulated reverbs have can have a lushness or life in the reverberation that, while
artificial, can be very pleasing.

Parameter 1: Liveliness
Parameter 2: Decay Time

PLATE MOD
A modulated plate reverb. Modulated reverbs have can have a lushness or life in the reverberation that, while
artificial, can be very pleasing.

Parameter 1: Liveliness
Parameter 2: Decay Time

8.2: REVERBS
 16, 22, 22MTK User Manual 8.2: REVERBS

LEXICON FX > REVERBS

SPRING
A Spring reverb is created by a pair of piezoelectric crystals one acting as a speaker and the other acting as a
microphone connected by a simple set of springs. The characteristic boing of a spring is an important
component of many classic rock and rockabilly guitar sounds.

Parameter 1: Liveliness
Parameter 2: Decay Time

GATED
A gated reverb uses a threshold setting to abruptly cut off the reverberant field, producing a distinctive effect
often used on pop percussion.

Parameter 1: Liveliness
Parameter 2: Decay Time

HALL & CHORUS

A hall reverb combined with chorus effect to thicken up the reverberant field.

Parameter 1: Decay Time

Parameter 2: Modulation Speed

PLATE & CHORUS

A plate reverb combined with chorus effect to thicken up the reverberant field.

Parameter 1: Decay Time

Parameter 2: Modulation Speed

HALL & DELAY

A hall reverb combined with a delay effect.

Parameter 1: Decay Time

Parameter 2: Delay Time

PLATE & DELAY

A plate reverb combined with a delay effect.

Parameter 1: Decay Time

Parameter 2: Delay Time

8.2: REVERBS
 16, 22, 22MTK User Manual 8.3: DELAYS & MODULATION

LEXICON FX > DELAYS & MODULATION

Delays repeat a sound a short time after it first occurs. Delay becomes echo when the output is fed
back into the input (feedback). This turns a single repeat into a series of repeats, each a little softer
than the last.

Modulation effects use a low frequency oscillator to vary frequency, amplitude, and filter parameters
over time.

SLAP (KARAOKE)
Slap echo is a distinctive vocal echo effect heard in classic Rock n Roll, Rockabilly, and other 'classic' genres, hence
its popularity in Karaoke!

Parameter 1: Number Of Repeats

Parameter 2: Delay Time

DELAY (2 SEC)
Basic delay algorithm with up to two seconds delay time.

Parameter 1: Number Of Repeats

Parameter 2: Delay Time

DELAY MOD
The modulated delay is enhanced by an LFO (low frequency oscillator) that produces a chorusing effect on the
delay repeats. This is a great delay for guitar and instrument passages that need that special something.

Parameter 1: Number Of Repeats

Parameter 2: Delay Time

TAPE
In the days before digital, tape echoes were created using a special tape recorder in which the magnetic recording
tape was looped, with closely-spaced recording and playback heads. The delay effect was created by the tape
moving in the space between the record and playback heads while delay time was adjusted by changing the
speed of the tape loop. Although very musical-sounding, wow and flutter combined with a significant loss of high
frequencies, and to some extent also low frequencies, are all elements commonly associated with tape echo.

Parameter 1: Number Of Repeats

Parameter 2: Delay Time

8.3: DELAYS & MODULATION

 16, 22, 22MTK User Manual 8.3: DELAYS & MODULATION

LEXICON FX > DELAYS & MODULATION

LO FI
Delay with limited bandwidth that degrades the signal in a pleasing way for a crunchy percussion or any where a
lo-fidelity effect will enhance the feel.

Parameter 1: Number Of Repeats

Parameter 2: Delay Time

STUDIO CHORUS
Chorus creates a lush, full sound by combining two or more signals together where one is unaffected and the
other signals vary in pitch very slightly over time. Chorus is commonly used to fatten up tracks and to add body
to guitars without colouring the original tone. Chorus can also be used with discretion to thicken a vocal track.
Studio Chorus is a studio-quality chorus with a wide stereo image.

Parameter 1: Modulation Speed

Parameter 2: Modulation Depth

MODERN CHORUS
Dual-voice chorusing thats both very rich and very smooth.

Parameter 1: Modulation Speed

Parameter 2: Modulation Depth

TREMOLO
A basic stereo amplitude (volume) modulation effect.

Parameter 1: Modulation Speed

Parameter 2: Modulation Depth

ROTARY
Rotary speaker cabinets were designed to provide a majestic vibrato/choir effect for electronic theatre and
church organs. This algorithm emulates the famous Leslie speaker with two counter-rotating elements: a
high-frequency horn and a low-frequency rotor with slow and fast speeds.

Parameter 1: Modulation Speed

Parameter 2: Modulation Depth

8.3: DELAYS & MODULATION

 16, 22, 22MTK User Manual 8.3: DELAYS & MODULATION

LEXICON FX > DELAYS & MODULATION

VIBRATO
Vibrato is obtained by smoothly modulating the pitch of the signal just sharp and flat of the original at a
determined rate.

Parameter 1: Modulation Speed

Parameter 2: Modulation Depth

VIBRAPAN
A unique dual voice vibrato effect with a variable phase control for the voices.

Parameter 1: Modulation Speed

Parameter 2: Modify / Phase Control

PHASER
The Phaser automatically moves frequency notches up and down the spectrum of the signal by means of a low
frequency oscillator (LFO), creating an oscillating comb filter type effect. This effect is very useful on keyboards
(especially pad presets) and guitars.

Parameter 1: Modulation Speed

Parameter 2: Modulation Depth

8.3: DELAYS & MODULATION

 16, 22, 22MTK User Manual APPENDIX 1: NO SOUND?

NO SOUND

A Troubleshooting Guide.
Is an input failing to appear at appearing at an output? The best approach it is to first make sure the
input is valid, and then work through the signal path to find out where the break is... Check the exact
audio path of any signal by referring to the signal path diagrams in Chapter 4.

Check Solos
If a PFL light on an input channel is lit, or the AFL/PFL ACTIVE LED (below main audio meter) then a solo is active
and all channels except those that are soloed will be muted. This will only affect the headphones output.

Clear all active Solos by pressing any illuminated Input Channel PFL buttons and any engaged Aux Master AFL buttons.

Check Input Channel Path To Solo Bus

The channel solo can be very useful here. If you Solo the channel it will send a post-EQ, pre-Mute signal to the Solo
bus and you should be able to see signal indicated on the main meters, or hear it in the headphones.
Things that might prevent the signal getting that far include a GAIN control set too low, phantom power not switched
on for a source that requires it (condenser microphone, active DI, etc.), or an active SUB RTN switch on a channel
where there is no USB input (MTK models only).
Check the Input Channel routing diagram (Section 4.1) and ensure the channel controls are set up correctly.

Check Input Channel Path To Routing

If the signal is present on the Solo bus with PFL engaged, the problem might be further down the input channel. It
could be simply that the Mute is active, or the fader is down - or there could be a problem with the routing.
For a signal to go to the Main Stereo Bus or to a Group Bus, the corresponding routing switch must be engaged
(MST, 1-2, or 3-4). Also, a pan or balance control can have a significant effect - if the signal is routed to Groups 1-2,
for example, and the pan control is full left (Group 1), you wont hear anything from the Group 2 bus.
Check Mute and fader status, and that the channel routing selections are correct.

Check Bus Masters

If you have routed signal to the Main Stereo bus or a Group bus, or you have turned up the channels contribution
to an Aux bus, then the master controls for that bus must be set correctly. For example, if the signal is routed to the
Stereo master but the Stereo Master fader is down, you wont hear anything.
Check the controls on any Bus Masters that the signal is routed to.

No FX?
For an internal FX to be heard, there must be a source contribution from a valid input. Increase the level to the FX
bus using the Aux/FX control (Aux 4/FX for Signature 16, Aux 4/FX and Aux 5/FX for Signature 22 and 22MTK.
Also, the signal is return through the corresponding FX Return Channel. Troubleshoot this signal path as you would
do for a normal input channel.
The internal FX routing has three stages - send, processor, and return. All three must be set correctly for the FX to be heard.

APPENDIX 1: NO SOUND?