August 10, 2010

Revision 2

imageRUNNER ADVANCE 8105 / 8095 / 8085 Series

Service Manual

Product Overview
Technology
Periodic Service
Parts Replacement and Clearning
Adjustment
Troubleshooting
Error Code
Service Mode
Installation Appendix
fineline6
1 2 3 4 5 6 7 8 9
 Application
This manual has been issued by Canon Inc. for qualified persons to learn technical theory, The following paragraph does not apply to any countries where such provisions are
installation, maintenance, and repair of products. This manual covers all localities where the inconsistent with local law.
products are sold. For this reason, there may be information in this manual that does not
apply to your locality. Trademarks
The product names and company names used in this manual are the registered trademarks
Corrections of the individual companies.
This manual may contain technical inaccuracies or typographical errors due to improvements
or changes in products. When changes occur in applicable products or in the contents of this Copyright
manual, Canon will release technical information as the need arises. In the event of major This manual is copyrighted with all rights reserved. Under the copyright laws, this manual may
changes in the contents of this manual over a long or short period, Canon will issue a new not be copied, reproduced or translated into another language, in whole or in part, without the
edition of this manual. written consent of Canon Inc.

(C) CANON INC. 2010

Caution
Use of this manual should be strictly supervised to avoid disclosure of confidential
information.

fineline6
 Explanation of Symbols The following rules apply throughout this Service Manual:
The following symbols are used throughout this Service Manual.
1. Each chapter contains sections explaining the purpose of specific functions and the
Symbols Explanation Symbols Explanation relationship between electrical and mechanical systems with reference to the timing of
operation.
In the diagrams, represents the path of mechanical drive; where a signal name
Check. Remove the claw.
accompanies the symbol, the arrow indicates the direction of the electric
signal.
The expression "turn on the power" means flipping on the power switch, closing the
Check visually. Insert the claw. front door, and closing the delivery unit door, which results in supplying the machine with
power.

2. In the digital circuits, '1' is used to indicate that the voltage level of a given signal is
Check the noise. Use the bundled part.
"High", while '0' is used to indicate "Low". (The voltage value, however, differs from
circuit to circuit.) In addition, the asterisk (*) as in "DRMD*" indicates that the DRMD
signal goes on when '0'.
Disconnect the connector. Push the part. In practically all cases, the internal mechanisms of a microprocessor cannot be checked
in the field. Therefore, the operations of the microprocessors used in the machines
are not discussed: they are explained in terms of from sensors to the input of the DC
controller PCB and from the output of the DC controller PCB to the loads.
Connect the connector. Plug the power cable.

The descriptions in this Service Manual are subject to change without notice for product

Remove the cable/wire

improvement or other purposes, and major changes will be communicated in the form of
from the cable guide or wire Turn on the power. Service Information bulletins.
saddle. All service persons are expected to have a good understanding of the contents of this Service
Manual and all relevant Service Information bulletins and be able to identify and isolate faults
Set the cable/wire to the in the machine.
cable guide or wire saddle.

Remove the screw.

Tighten the screw.

fineline6
 Blank Page

fineline6
 Contents
Specifications----------------------------------------------------------------- 1-10
Product Specifications------------------------------------------------------------1-10
Power Supply Specifications:--------------------------------------------------- 1-11
Weight and Size-------------------------------------------------------------------- 1-11
Productivity (Print Speed)--------------------------------------------------------1-12
Safety Precautions Paper Type--------------------------------------------------------------------------1-13
CDRH Act------------------------------------------------------------------------0-2 External View/Internal View----------------------------------------------- 1-24
Laser Safety---------------------------------------------------------------------0-2 External View-----------------------------------------------------------------------1-24
Handling of Laser System---------------------------------------------------0-2 External Cover-------------------------------------------------------------------------------1-24
Turn power switch ON--------------------------------------------------------0-3 Switches, I/F, Others-----------------------------------------------------------------------1-25
Safety of Toner------------------------------------------------------------------0-3 Cross-Section View---------------------------------------------------------------1-25
About Toner-------------------------------------------------------------------------- 0-3 Operation----------------------------------------------------------------------- 1-26
Toner on Clothing or Skin--------------------------------------------------------- 0-3 Power Switch-----------------------------------------------------------------------1-26
Notes Before it Works Serving----------------------------------------------0-3 Types of Power Switches-----------------------------------------------------------------1-26
Points to Note on Turning ON/OFF the Power Switch----------------------------1-26
Points to Note at Cleaning---------------------------------------------------0-4
Control Panel-----------------------------------------------------------------------1-27
1 Product Overview Control Panel--------------------------------------------------------------------------------1-27
Main Menu------------------------------------------------------------------------------------1-27
Product Lineup------------------------------------------------------------------1-2 Differences in Main Menu----------------------------------------------------------------1-28
Main Body---------------------------------------------------------------------------- 1-2 Settings/Registration Menu--------------------------------------------------------------1-28
Pickup/Delivery System Option------------------------------------------------- 1-2 Differences in Settings/Registration Menu-------------------------------------------1-29
Applicable Option for Each Model------------------------------------------------------- 1-2
Required Options/Conditions------------------------------------------------------------- 1-3 2 Technology
Scanning System Options-------------------------------------------------------- 1-4
Basic Configuration------------------------------------------------------------2-2
Required Options and Conditions------------------------------------------------------- 1-4
Functional Configuration---------------------------------------------------------- 2-2
Function Expansion System Options------------------------------------------ 1-5
Basic Sequence--------------------------------------------------------------------- 2-3
Required Options and Conditions------------------------------------------------------- 1-5
Basic sequence at power ON------------------------------------------------------------ 2-3
Features--------------------------------------------------------------------------1-7
Basic sequence at printing
Product Features-------------------------------------------------------------------- 1-7
<Condition: A4 1-sided (2 sheets), Right deck, Reverse delivery>------------- 2-4
Service Features-------------------------------------------------------------------- 1-7 Basic sequence at printing
Improved Service Operability------------------------------------------------------------- 1-7
<Condition: A4 2-sided (2 sheets), Right deck, Reverse delivery>------------- 2-5
New Service Mode-------------------------------------------------------------------------- 1-8
Main Controller-----------------------------------------------------------------2-6
Improved Upgrading Operability--------------------------------------------------------- 1-8
Overview------------------------------------------------------------------------------ 2-6
Jam/Error Code Display Specifications------------------------------------------------ 1-9
Features---------------------------------------------------------------------------------------- 2-6
Applying New Connectors----------------------------------------------------------------- 1-9
Specifications/configuration--------------------------------------------------------------- 2-7
HDD--------------------------------------------------------------------------------------------2-10
Boot/Shutdown sequence---------------------------------------------------------------- 2-11

fineline6
 Controls------------------------------------------------------------------------------2-12 Controls------------------------------------------------------------------------------2-53
Flow of Image Data------------------------------------------------------------------------2-12 Exposure--------------------------------------------------------------------------------------2-54
Security features (encryption key and certificate, password protection)------2-13 Primary Charging---------------------------------------------------------------------------2-55
High capacity HDD (Option)-------------------------------------------------------------2-22 Developing-----------------------------------------------------------------------------------2-57
HDD mirroring feature (option)----------------------------------------------------------2-22 Transfer---------------------------------------------------------------------------------------2-59
Removable HDD (option)-----------------------------------------------------------------2-27 Separation------------------------------------------------------------------------------------2-63
HDD Encryption/ Mirroring Kit (optional)----------------------------------------------2-28 Drum Cleaning------------------------------------------------------------------------------2-65
Service Operations----------------------------------------------------------------2-31 Drum-related Issues-----------------------------------------------------------------------2-66
HDD--------------------------------------------------------------------------------------------2-31 Drum Heater Control-----------------------------------------------------------------------2-67
Main Controller PCB 1--------------------------------------------------------------------2-32 Toner Supply Area--------------------------------------------------------------------------2-70
Main Controller PCB 2--------------------------------------------------------------------2-33 Waste Toner Feeding Area---------------------------------------------------------------2-72
TPM PCB-------------------------------------------------------------------------------------2-34 Image Stabilization Control--------------------------------------------------------------2-74
Flash PCB------------------------------------------------------------------------------------2-35 Auxiliary Control-----------------------------------------------------------------------------2-83
Laser Exposure System---------------------------------------------------- 2-36 Servicing-----------------------------------------------------------------------------2-88
Overview-----------------------------------------------------------------------------2-36 Periodically Replaced Parts--------------------------------------------------------------2-88
Overview--------------------------------------------------------------------------------------2-36 Consumable Parts--------------------------------------------------------------------------2-88
Specifications--------------------------------------------------------------------------------2-37 Periodical Servicing List------------------------------------------------------------------2-88
Parts Configuration-------------------------------------------------------------------------2-37 When Replacing Parts--------------------------------------------------------------------2-89
Controls------------------------------------------------------------------------------2-38 Major Adjustments--------------------------------------------------------------------------2-93
Overview--------------------------------------------------------------------------------------2-38 Troubleshooting-----------------------------------------------------------------------------2-94
Laser ON Timing Control-----------------------------------------------------------------2-38 Fixing-------------------------------------------------------------------------- 2-104
Laser Beam Intensity Control------------------------------------------------------------2-40 Overview--------------------------------------------------------------------------- 2-104
Duplex print magnification correction--------------------------------------------------2-41 Characteristics----------------------------------------------------------------------------- 2-104
Polygon Motor Control--------------------------------------------------------------------2-42 Specifications------------------------------------------------------------------------------ 2-105
Laser Shutter Control----------------------------------------------------------------------2-43 Parts configuration----------------------------------------------------------------------- 2-106
Servicing-----------------------------------------------------------------------------2-44 Drive configuration----------------------------------------------------------------------- 2-107
Periodically Replaced Parts--------------------------------------------------------------2-44 Controls---------------------------------------------------------------------------- 2-108
Consumable Parts--------------------------------------------------------------------------2-44 Overview------------------------------------------------------------------------------------ 2-108
Periodical Servicing List------------------------------------------------------------------2-44 Fixing temperature control------------------------------------------------------------- 2-108
When Replacing Parts--------------------------------------------------------------------2-44 Down sequence control----------------------------------------------------------------- 2-112
Major Adjustments--------------------------------------------------------------------------2-44 Paper Anti-wrapping Control----------------------------------------------------------- 2-114
Image Formation System-------------------------------------------------- 2-45 Thermistor reciprocating control------------------------------------------------------ 2-115
Overview-----------------------------------------------------------------------------2-45 Upper separation claw reciprocating control--------------------------------------- 2-116
Overview--------------------------------------------------------------------------------------2-45 Cleaning web drive control------------------------------------------------------------- 2-116
Specifications--------------------------------------------------------------------------------2-46 Cleaning web length detection-------------------------------------------------------- 2-117
Parts Configuration-------------------------------------------------------------------------2-47 Protective function------------------------------------------------------------------------ 2-118
Drive Configuration-------------------------------------------------------------------------2-49
Print Process---------------------------------------------------------------------------------2-52

fineline6
 Servicing--------------------------------------------------------------------------- 2-119 Jam Dection----------------------------------------------------------------------- 2-153
Periodically Replaced Parts------------------------------------------------------------ 2-119 Jam Code List----------------------------------------------------------------------------- 2-153
Consumable Parts------------------------------------------------------------------------ 2-119 Forced Paper Feed Control------------------------------------------------------------ 2-155
Periodical Servicing List---------------------------------------------------------------- 2-119 Servicing--------------------------------------------------------------------------- 2-156
When Replacing Parts------------------------------------------------------------------ 2-120 Periodically Replaced Parts------------------------------------------------------------ 2-156
Troubleshooting--------------------------------------------------------------------------- 2-121 Consumable Parts------------------------------------------------------------------------ 2-156
Pickup / Feed System----------------------------------------------------- 2-123 Periodical Servicing List---------------------------------------------------------------- 2-156
Overview--------------------------------------------------------------------------- 2-123 When Replacing Parts------------------------------------------------------------------ 2-156
Overview------------------------------------------------------------------------------------ 2-123 Major Adjustments------------------------------------------------------------------------ 2-156
Specifications------------------------------------------------------------------------------ 2-124 Troubleshooting--------------------------------------------------------------------------- 2-156
Parts configuration----------------------------------------------------------------------- 2-125 External Auxiliary System------------------------------------------------ 2-157
Drive Configuration----------------------------------------------------------------------- 2-127 Overview--------------------------------------------------------------------------- 2-157
Paper path---------------------------------------------------------------------------------- 2-128 Power Supply Configuration----------------------------------------------------------- 2-157
Interval speed------------------------------------------------------------------------------ 2-129 Controls---------------------------------------------------------------------------- 2-158
Various types of control----------------------------------------------------------------- 2-130 Power supply control-------------------------------------------------------------------- 2-158
Deck/Cassette Pickup Unit---------------------------------------------------- 2-131 Fan Control--------------------------------------------------------------------------------- 2-163
Basic Movement-------------------------------------------------------------------------- 2-131 Counter control---------------------------------------------------------------------------- 2-164
Deck/Cassette detection---------------------------------------------------------------- 2-132 Servicing--------------------------------------------------------------------------- 2-166
Paper Size Detection------------------------------------------------- 2-133 Periodically Replaced Parts------------------------------------------------------------ 2-166
Paper Level Detection------------------------------------------------------------------- 2-135 Consumable Parts------------------------------------------------------------------------ 2-166
Paper Detection--------------------------------------------------------------------------- 2-137 Periodical Servicing---------------------------------------------------------------------- 2-166
Lifter Control------------------------------------------------------------------------------- 2-138 DC Controller PCB----------------------------------------------------------------------- 2-166
Pickup Retry Control--------------------------------------------------------------------- 2-139 Troubleshooting--------------------------------------------------------------------------- 2-166
Multi-purpose Tray Pickup Unit----------------------------------------------- 2-140 MEAP------------------------------------------------------------------------- 2-169
Basic Movement-------------------------------------------------------------------------- 2-140 Changes---------------------------------------------------------------------------- 2-169
Paper Size Detection-------------------------------------------------------------------- 2-141 Abolition of Supplying MEAP Administrator's CD with Machine-------------- 2-169
Paper Detection--------------------------------------------------------------------------- 2-141 Checking the Operating Environment-------------------------------------- 2-169
Registration Unit----------------------------------------------------------------- 2-142 Outline--------------------------------------------------------------------------------------- 2-169
Pre-registration Control----------------------------------------------------------------- 2-142 SMS------------------------------------------------------------------------------------------ 2-169
Registration Control---------------------------------------------------------------------- 2-143 SSO-H Management-------------------------------------------------------------------- 2-170
Registration Deceleration Control---------------------------------------------------- 2-143 Setting Up the Network--------------------------------------------------------- 2-172
Registration Acceleration Control----------------------------------------------------- 2-144 Network configuration process-------------------------------------------------------- 2-172
Post-transfer Guide Attraction Control---------------------------------------------- 2-144 Login to SMS---------------------------------------------------------------------- 2-173
Delivery/Reverse Unit----------------------------------------------------------- 2-145 Outline--------------------------------------------------------------------------------------- 2-173
Basic Operation--------------------------------------------------------------------------- 2-145 Login by Password Authentication--------------------------------------------------- 2-173
Duplex Unit--------------------------------------------------------------------------------- 2-147 Login by RLS Authentication----------------------------------------------------------- 2-174
Side Registration Control--------------------------------------------------------------- 2-148 Initial Display Languages of SMS---------------------------------------------------- 2-175
Circulation quantity and limit----------------------------------------------------------- 2-149

fineline6
 Setting the method to login to SMS----------------------------------------- 2-176 Login Service--------------------------------------------------------------------- 2-194
Outline--------------------------------------------------------------------------------------- 2-176 About Login Service--------------------------------------------------------------------- 2-194
Setting for login by Password Authentication-------------------------------------- 2-176 Default Authentication overview------------------------------------------------------ 2-195
Setting for login by RLS Authentication--------------------------------------------- 2-177 SSO-H (Single Sign-On-H) overview------------------------------------------------ 2-195
Checking MEAP Application Management Page------------------------ 2-178 Authentication methods of SSO-H--------------------------------------------------- 2-195
About MEAP Application Management Page-------------------------------------- 2-178 Access Mode in Sites-------------------------------------------------------------------- 2-197
Starting and Stopping a MEAP Application-------------------------------- 2-179 Environment confirmation-------------------------------------------------------------- 2-198
Procedure to start and stop a MEAP application--------------------------------- 2-179 Specification of SSO-H------------------------------------------------------------------ 2-199
Checking the Platform Information------------------------------------------ 2-180 Changing Login Services------------------------------------------------------ 2-199
The check procedure of the platform information-------------------------------- 2-180 Steps to Change Login Services----------------------------------------------------- 2-199
MEAP Specifications------------------------------------------------------------ 2-180 Initializing the Password------------------------------------------------------- 2-200
What is MEAP Specifications (MEAP Spec Version)?-------------------------- 2-180 Outline--------------------------------------------------------------------------------------- 2-200
About Name-------------------------------------------------------------------------------- 2-180 Procedure to initialize the SMS login password---------------------------------- 2-200
Mechanism--------------------------------------------------------------------------------- 2-180 Creating a Backup, Formatting the Hard Disk, Restoring
MEAP Application System Information------------------------------------- 2-182 with the Backup data, Using the SST--------------------------------------- 2-201
Outline--------------------------------------------------------------------------------------- 2-182 Outline--------------------------------------------------------------------------------------- 2-201
Checking the System Information of a MEAP Application with SMS-------- 2-182 Backup Items------------------------------------------------------------------------------ 2-201
Printing the System Information of a MEAP Application------------------------ 2-182 Requirements for Backup Using the SST------------------------------------------ 2-202
Content of MEAP system information----------------------------------------------- 2-183 Making a Backup and Formatting Hard Disk Drive
Installing an Application-------------------------------------------------------- 2-184 with Service Support Tool--------------------------------------------------------------- 2-202
Resource------------------------------------------------------------------------------------ 2-184 Procedures to Restore Backup Data------------------------------------------------ 2-204
Procedure to install applications------------------------------------------------------ 2-184 Replacing the Hard Disk Drive----------------------------------------------- 2-204
Adding a License File----------------------------------------------------------- 2-186 Outline--------------------------------------------------------------------------------------- 2-204
Procedure adding a license file------------------------------------------------------- 2-186 HDD replacement procedure---------------------------------------------------------- 2-205
Disabling a License File-------------------------------------------------------- 2-187 MEAP Safe Mode (level 2)---------------------------------------------------- 2-205
Procedure disabling a license file (suspending a license)---------------------- 2-187 Outline--------------------------------------------------------------------------------------- 2-205
Downloading / Removing an Invalidated License File------------------ 2-189 Starting in Safe Mode------------------------------------------------------------------- 2-205
Outline--------------------------------------------------------------------------------------- 2-189 How to cancel MEAP SAFE mode--------------------------------------------------- 2-206
Procedure downloading / removing an invalidated license file---------------- 2-189 Setting HTTP port for MEAP application (level 2)----------------------- 2-207
Reusable license----------------------------------------------------------------- 2-190 Outline--------------------------------------------------------------------------------------- 2-207
Outline--------------------------------------------------------------------------------------- 2-190 Port setup procedure of HTTP Server----------------------------------------------- 2-207
License for forwarding---------------------------------------------------------- 2-191 Port setup procedure of HTTPS Server--------------------------------------------- 2-208
Outline--------------------------------------------------------------------------------------- 2-191 Using USB Devices------------------------------------------------------------- 2-210
Procedure to create license for forwarding----------------------------------------- 2-191 USB Driver--------------------------------------------------------------------------------- 2-210
Uninstalling an Application----------------------------------------------------- 2-193 Initialization of MEAP driver priority registration---------------------------------- 2-212
Procedure to uninstall an application------------------------------------------------ 2-193 USB Device report print----------------------------------------------------------------- 2-212
Reference material-------------------------------------------------------------- 2-215
Glossary------------------------------------------------------------------------------------- 2-215

fineline6
 Option for exclusive individual measure----------------------------------- 2-217 List of Motor-------------------------------------------------------------------------4-40
Display Setting of Copy Icon (level2)------------------------------------------------ 2-217 List of Sensor-----------------------------------------------------------------------4-46
Error at starting up the MEAP application/Setting List of Switch------------------------------------------------------------------------4-52
to hide JAM screen (level 2)----------------------------------------------------------- 2-217 List of PCB---------------------------------------------------------------------------4-54
Setting of Screen Transition from MEAP Screen Heater,others------------------------------------------------------------------------4-58
to the Standard Screen (level2)------------------------------------------------------- 2-218
Connector List----------------------------------------------------------------------4-60
Embedded RDS------------------------------------------------------------ 2-219 Main Controller--------------------------------------------------------------- 4-80
Product Overview---------------------------------------------------------------- 2-219 Removing Main Controller PCB 1---------------------------------------------4-80
Overview------------------------------------------------------------------------------------ 2-219
Removing Main Controller PCB 2---------------------------------------------4-85
Features and benefits------------------------------------------------------------------- 2-219
Major Functions--------------------------------------------------------------------------- 2-219
Laser Exposure System---------------------------------------------------- 4-92
Removing the Laser Scanner Unit---------------------------------------------4-92
Limitations------------------------------------------------------------------------- 2-220
Cleaning the Dust Collecting Glass-------------------------------------------4-95
Service Mode Menu Transmission Function--------------------------------------- 2-220
Service cautions------------------------------------------------------------------ 2-220 Image Formation System-------------------------------------------------- 4-96
Removing the Primary Charging Assembly---------------------------------4-96
E-RDS Setup---------------------------------------------------------------------- 2-221
Confirmation and preparation in advance------------------------------------------ 2-221 Removing the Primary Charging Wire Cleaner,
E-RDS-related setting items----------------------------------------------------------- 2-224 Cleaner Holder (Right/Left)------------------------------------------------------4-97
Steps to E-RDS settings---------------------------------------------------------------- 2-225 Replacing the Primary Charging Assembly Grid Wire------------------ 4-100
Steps to Service Call button settings------------------------------------------------ 2-228 Replacing the Primary Charging Wire-------------------------------------- 4-103
Steps to Service Browser settings--------------------------------------------------- 2-230 Cleaning the Primary Charging Assembly Grid Wire------------------- 4-105
Initializing E-RDS settings-------------------------------------------------------------- 2-231 Removing the Pre-transfer Charging Assembly-------------------------- 4-106
FAQ---------------------------------------------------------------------------------- 2-232 Removing the Pre-transfer Charging Wire Cleaner,
Troubleshooting------------------------------------------------------------------ 2-234 Cleaner Holder------------------------------------------------------------------- 4-108
Error code and strings---------------------------------------------------------- 2-237 Replacing the Pre-transfer Charging Wire--------------------------------- 4-110
Cleaning the Pre-transfer Charging Wire---------------------------------- 4-112
3 Periodic Service Removing the Process Unit--------------------------------------------------- 4-114
Periodical Service Operation Item-----------------------------------------3-2 Cleaning the Process Unit----------------------------------------------------- 4-115
Removing the Drum Cleaning Unit------------------------------------------ 4-116
4 Parts Replacement and Clearning Removing the Drum Cleaning Blade---------------------------------------- 4-117
List of Parts----------------------------------------------------------------------4-2 Cleaning the Drum Cleaning Unit-------------------------------------------- 4-119
List of External / Internal Cover------------------------------------------------- 4-2 Replacing the Pre-exposure Plastic Film---------------------------------- 4-120
List of Main Unit--------------------------------------------------------------------- 4-4 Removing the Drum Unit------------------------------------------------------- 4-121
Periodic Replacing Parts,Durable Parts,Cleaning Parts-----------------4-10 Removing the Photosensitive Drum----------------------------------------- 4-122
Periodic Replacing Parts,Durable Parts ---------------------------------------------4-10 Cleaning Photosensitive Drum----------------------------------------------- 4-125
List of Cleaning Parts----------------------------------------------------------------------4-20 Cleaning the Drum edges------------------------------------------------------ 4-126
List of Fan----------------------------------------------------------------------------4-34 Removing the Cleaner Separation Claw----------------------------------- 4-127
List of Clutch / Solenoid----------------------------------------------------------4-36 Removing the Side Seal------------------------------------------------------- 4-127

fineline6
 Removing the Developing Assembly---------------------------------------- 4-128 Removing the Main Thermistor----------------------------------------------- 4-186
Cleaning the Developing Assembly----------------------------------------- 4-131 Removing the Sub Thermistor 1--------------------------------------------- 4-188
Removing the ETB Unit-------------------------------------------------------- 4-133 Removing the Sub Thermistor 2--------------------------------------------- 4-189
Removing the ETB-------------------------------------------------------------- 4-135 Removing the Upper Separation Claw------------------------------------- 4-190
Cleaning the ETB---------------------------------------------------------------- 4-136 Cleaning the Upper Separation Claw--------------------------------------- 4-190
Removing the Transfer Roller------------------------------------------------- 4-137 Removing the Thermoswitch 2----------------------------------------------- 4-192
Removing the ETB Cleaning Blade----------------------------------------- 4-138 Pickup/Feed System------------------------------------------------------ 4-194
Removing the ETB Brush Roller--------------------------------------------- 4-138 Removing the Left Pickup Deck---------------------------------------------- 4-194
Removing the Waste Toner Container-------------------------------------- 4-141 Removing the Left Deck Pickup Roller------------------------------------- 4-194
Removing the Drum Heater--------------------------------------------------- 4-142 Removing the Left Deck Feed Roller--------------------------------------- 4-195
Removing the Primary Charging Shutter Unit---------------------------- 4-143 Removing the Right Pickup Deck-------------------------------------------- 4-195
Removing the Pre-transfer Charging Assembly Shutter Unit--------- 4-146 Removing the Left Deck Separation Roller/Cleaning
Removing the Patch Sensor-------------------------------------------------- 4-149 the Left Deck Pickup Sensor 2 (PS20)------------------------------------- 4-196
Removing the Drum Brush Roller-------------------------------------------- 4-150 Removing the Right Deck Pickup Roller----------------------------------- 4-196
Removing the ETB Drive Unit------------------------------------------------ 4-151 Removing the Right Deck Feed Roller------------------------------------- 4-197
Removing the Transfer Cleaning Unit-------------------------------------- 4-153 Removing the Right Deck Separation Roller/Cleaning
Removing the Post-transfer Static Eliminator----------------------------- 4-154 the Right Deck Pickup Sensor 2 (PS19)----------------------------------- 4-197
Removing the Toner Receptacle Tray-------------------------------------- 4-155 Removing the Upper Cassette----------------------------------------------- 4-198
Removing the Hopper Unit---------------------------------------------------- 4-156 Removing the Upper Cassette Pickup Roller----------------------------- 4-199
Removing the Buffer Unit------------------------------------------------------ 4-160 Removing the Upper Cassette Feed Roller------------------------------- 4-199
Removing the Potential Control PCB Unit--------------------------------- 4-163 Removing the Upper Cassette Separation Roller/Cleaning the Cassette
Removing the Waste Toner Feed Unit-------------------------------------- 4-165 3 Pickup Sensor 2 (PS21)----------------------------------------------------- 4-200
Removing the Drum Drive Unit----------------------------------------------- 4-168 Removing the Lower Cassette----------------------------------------------- 4-201
Removing the Developing Drive Unit--------------------------------------- 4-170 Removing the Lower Cassette Pickup Roller----------------------------- 4-201
Fixing-------------------------------------------------------------------------- 4-173 Removing the Lower Cassette Feed Roller------------------------------- 4-202
Removing the Fixing Assembly----------------------------------------------- 4-173 Removing the Lower Cassette Separation Roller/Cleaning
Cleaning the Fixing Inlet Guide,Fixing Inlet Sensor Flag, the Cassette 4 Pickup Sensor 1 (PS22)----------------------------------- 4-202
Fixing Right Stay, Dowel, Dowel Holder----------------------------------- 4-175 Removing the Multi-purpose Tray Feed Roller--------------------------- 4-203
Cleaning the Inner Delivery Roller------------------------------------------- 4-176 Removing the Multi-purpose Tray Separation Roller------------------- 4-205
Cleaning the Fixing Oil Pan--------------------------------------------------- 4-177 Cleaning the Pickup and Fixing Feed Assembly------------------------- 4-206
Removing the Fixing Cleaning Web----------------------------------------- 4-177 Removing the Left Deck Pickup Unit---------------------------------------- 4-215
Cleaning the Fixing Roller Static Eliminator------------------------------- 4-179 Removing the Right Deck Pickup Unit-------------------------------------- 4-216
Separating the Fixing Upper Unit from the Fixing Lower Unit-------- 4-180 Removing the Cassettes 3 and 4 Pickup Unit---------------------------- 4-217
Removing the Fixing Roller, Insulating Bush and Thrust Stopper--- 4-182 Removing the Vertical Path Cassette Pickup Drive Unit--------------- 4-218
Removing the Pressure Roller------------------------------------------------ 4-184 Removing the Registration Unit---------------------------------------------- 4-221
Removing the Pressure Roller Static Eliminator------------------------- 4-185 Removing the Left Deck Pickup Drive Unit-------------------------------- 4-224

fineline6
 Removing the Main Drive Unit------------------------------------------------ 4-225 6 Troubleshooting
External Auxiliary System------------------------------------------------ 4-230
Test Print-------------------------------------------------------------------------6-2
Removing the Filter (for primary charging)-------------------------------- 4-230
Overview------------------------------------------------------------------------------ 6-2
Removing the Ozone Filter---------------------------------------------------- 4-230
How to View the Test Print-------------------------------------------------------- 6-3
Removing the DC Controller PCB------------------------------------------- 4-231
Grid (TYPE=1)-------------------------------------------------------------------------------- 6-3
Removing the Power Supply Assembly------------------------------------ 4-234 17 gradations (TYPE=2/3)----------------------------------------------------------------- 6-3
Removing the Fixing Power Unit--------------------------------------------- 4-235 Solid white (TYPE=4)----------------------------------------------------------------------- 6-4
Removing the Feed Driver PCB---------------------------------------------- 4-236 Halftone (TYPE=5/6/11/12/13/14)------------------------------------------------------- 6-4
Removing the Upper High Voltage Unit------------------------------------ 4-237 Solid black (TYPE=7)----------------------------------------------------------------------- 6-5
Removing the Upright Control Panel---------------------------------------- 4-238 Horizontal line (TYPE=8/9/10)------------------------------------------------------------ 6-5
Image Faults--------------------------------------------------------------------6-6
5 Adjustment Trailing Edge Shock Imaget------------------------------------------------------ 6-6
Overview-------------------------------------------------------------------------5-2 Uneven density correction by 2D shading------------------------------------ 6-7
When replacing parts---------------------------------------------------------5-2 ADF black line---------------------------------------------------------------------- 6-11
Controller System------------------------------------------------------------------- 5-2 Bleed-thru/Soil appeared on the back of the paper
HDD--------------------------------------------------------------------------------------------- 5-2 (Staple Finisher D1/Booklet Finisher D1)------------------------------------6-12
Main Controller PCB 1--------------------------------------------------------------------- 5-4 White line (foreign matter between Developing Sleeves)---------------6-13
Main Controller PCB 2--------------------------------------------------------------------- 5-4 Separation Failure Jam due to Deformation of Separation Claw------6-15
TPM PCB-------------------------------------------------------------------------------------- 5-6 Image error due to soil attached to the Cleaning Brushes for
Flash PCB------------------------------------------------------------------------------------- 5-6 the Duplex Right Roller and the Duplex Outlet Roller--------------------6-16
Image Formation System--------------------------------------------------------- 5-7 Uneven density---------------------------------------------------------------------6-22
Primary Charging Wire--------------------------------------------------------------------- 5-7
Smeared image--------------------------------------------------------------------6-23
Primary Charging Assembly-------------------------------------------------------------- 5-7
Image failure due to the temperature rising at the edge of
Pre-transfer Charging Assembly--------------------------------------------------------- 5-9
the Fixing Roller (crepe mark)--------------------------------------------------6-25
Pre-transfer Charging Wire--------------------------------------------------------------- 5-9
Photosensitive Drum------------------------------------------------------------------------ 5-9
MTF Adjustment--------------------------------------------------------------------6-26
Adjustment Procedure---------------------------------------------------------------------6-26
Drum Side Seals (Front and Rear)-----------------------------------------------------5-10
When Making Fine Adjustment After Sampling the MTF Value-----------------6-27
Developing Assembly----------------------------------------------------------------------5-10
When Disabling the MTF Adjustment--------------------------------------------------6-27
Potential Sensor / Potential Control PCB---------------------------------------------5-10
ETB Unit / ETB------------------------------------------------------------------------------ 5-11 Feed Faults-------------------------------------------------------------------- 6-28
Patch Sensor-------------------------------------------------------------------------------- 5-11 Paper wrinkle-----------------------------------------------------------------------6-28
Waste Toner Container-------------------------------------------------------------------- 5-11 Other---------------------------------------------------------------------------- 6-28
Fixing System----------------------------------------------------------------------- 5-11 Adjusting rotation of the Upright Control Panel Arm----------------------6-28
Fixing Roller---------------------------------------------------------------------------------- 5-11 Remedy to be implemented when the ETB Disengage Member
External Auxiliary System--------------------------------------------------------5-12 (Transfer Frame Stopper) is left unremoved--------------------------------6-30
DC Controller PCB-------------------------------------------------------------------------5-12 Checking nip width----------------------------------------------------------------6-32

fineline6
 Version upgrade-------------------------------------------------------------- 6-33 7 Error Code
Overview-----------------------------------------------------------------------------6-33
Overview of Version Upgrade-----------------------------------------------------------6-33
Overview-------------------------------------------------------------------------7-2
Outline--------------------------------------------------------------------------------- 7-2
Writing System Software------------------------------------------------------------------6-34
Location code--------------------------------------------------------------------------------- 7-2
System Software Components----------------------------------------------------------6-35
Location code--------------------------------------------------------------------------------- 7-2
Note on Download Process--------------------------------------------------------------6-36
Points to Note When Clearing MN-CON----------------------------------------------- 7-2
Version Upgrade via SST--------------------------------------------------------6-36
Points to Note When Clearing HDD---------------------------------------------------- 7-2
Overview--------------------------------------------------------------------------------------6-36
Copying System Software----------------------------------------------------------------6-37 Error Code-----------------------------------------------------------------------7-3
Connection-----------------------------------------------------------------------------------6-39 Error Code Details------------------------------------------------------------------ 7-3
Downloading System Software (Assist mode)--------------------------------------6-40 E000 to E069--------------------------------------------------------------------------------- 7-3
Downloading System Software (Single mode)--------------------------------------6-42 E100 to E197--------------------------------------------------------------------------------7-13
Formatting HDD-----------------------------------------------------------------------------6-44 E202 to E280--------------------------------------------------------------------------------7-17
Backup----------------------------------------------------------------------------------------6-49 E301 to E355--------------------------------------------------------------------------------7-20
E400 to E490--------------------------------------------------------------------------------7-22
Version Upgrade using USB memoryStorage Device--------------------6-52
E500 to E5F9--------------------------------------------------------------------------------7-24
Relation between SST and USB memory storage device
E602-------------------------------------------------------------------------------------------7-41
Storage Device------------------------------------------------------------------------------6-52
E604 to E677--------------------------------------------------------------------------------7-74
Copying System Software----------------------------------------------------------------6-53
E710 to E753--------------------------------------------------------------------------------7-75
Connection-----------------------------------------------------------------------------------6-56
E804 to E996--------------------------------------------------------------------------------7-80
Upgrading System Software-------------------------------------------------------------6-57
Downloading/Writing System Software (Automatic)-------------------------------6-59 Jam Code---------------------------------------------------------------------- 7-83
Downloading System Software (Confirmation)--------------------------------------6-60 Jam Type-----------------------------------------------------------------------------7-83
Downloading System Software (Overwriting)---------------------------------------6-62 Main Unit-----------------------------------------------------------------------------7-84
Formatting HDD-----------------------------------------------------------------------------6-63 Duplex Color Image Reader-C1------------------------------------------------7-86
Backup----------------------------------------------------------------------------------------6-65 Paper Deck Unit-C1---------------------------------------------------------------7-87
Clearing Download File-------------------------------------------------------------------6-65 POD Deck Light-A1---------------------------------------------------------------7-87
Download Menu 2--------------------------------------------------------------------------6-65 Inserter-K1---------------------------------------------------------------------------7-88
Other Menu-----------------------------------------------------------------------------------6-65 Professional Puncher-C1/Integration Unit-B1------------------------------7-89
Troubleshooting--------------------------------------------------------------------6-66 PaperFolding Unit-H1-------------------------------------------------------------7-91
Error Code: E753-0001-------------------------------------------------------------------6-66 Staple Finisher-D1/Booklet Finisher-D1--------------------------------------7-92
Making Initial Checks------------------------------------------------------- 6-67 Alarm Code-------------------------------------------------------------------- 7-93
List of Initial Check Items--------------------------------------------------------6-67 List of Alarm Code-----------------------------------------------------------------7-93

fineline6
 8 Service Mode (SORTER>P058 to P059)----------------------------------------------------------------8-60
Staple Finisher - D1 / Booklet Finisher -D1 (SORTER>P001 to P059)-------8-60
Overview-------------------------------------------------------------------------8-2 Inner Trimmer - A1 (SORTER>P024 to P028)--------------------------------------8-75
Service Mode Menu---------------------------------------------------------------- 8-2 ADJUST------------------------------------------------------------------------------8-77
Service mode item explanations------------------------------------------------ 8-2 AE----------------------------------------------------------------------------------------------8-77
I/O information enhancement---------------------------------------------------- 8-3 ADJ-XY----------------------------------------------------------------------------------------8-77
Display of Error Code/Alarm Code description------------------------------ 8-3 CCD--------------------------------------------------------------------------------------------8-79
COPIER > OPTION > BODY, Item Segmentation-------------------------- 8-4 LASER-----------------------------------------------------------------------------------------8-89
Security features-------------------------------------------------------------------- 8-4 IMG-REG-------------------------------------------------------------------------------------8-89
Related service modes--------------------------------------------------------------------- 8-4 DEVELOP------------------------------------------------------------------------------------8-90
Switching Screen (Level 1 < - > 2)--------------------------------------------- 8-5 DENS------------------------------------------------------------------------------------------8-90
Language switch-------------------------------------------------------------------- 8-6 BLANK-----------------------------------------------------------------------------------------8-92
Back-up of service mode---------------------------------------------------------- 8-6 V-CONT---------------------------------------------------------------------------------------8-93
PASCAL---------------------------------------------------------------------------------------8-94
COPIER--------------------------------------------------------------------------8-7
HV-PRI----------------------------------------------------------------------------------------8-94
DISPLAY------------------------------------------------------------------------------ 8-7
HV-TR-----------------------------------------------------------------------------------------8-95
VERSION-------------------------------------------------------------------------------------- 8-7
FEED-ADJ---------------------------------------------------------------------------------- 8-102
USER------------------------------------------------------------------------------------------8-29
CST-ADJ------------------------------------------------------------------------------------ 8-106
ACC-STS-------------------------------------------------------------------------------------8-29
MISC----------------------------------------------------------------------------------------- 8-107
ANALOG--------------------------------------------------------------------------------------8-31
EXP-LED------------------------------------------------------------------------------------ 8-109
CST-STS--------------------------------------------------------------------------------------8-32
HV-STS----------------------------------------------------------------------------------------8-33
FUNCTION------------------------------------------------------------------------ 8-110
INSTALL------------------------------------------------------------------------------------- 8-110
CCD--------------------------------------------------------------------------------------------8-34
CCD------------------------------------------------------------------------------------------ 8-112
DPOT------------------------------------------------------------------------------------------8-37
DENS---------------------------------------------------------------------------------------- 8-113
DENS------------------------------------------------------------------------------------------8-38
DPC------------------------------------------------------------------------------------------ 8-114
SENSOR--------------------------------------------------------------------------------------8-39
CST------------------------------------------------------------------------------------------ 8-114
MISC-------------------------------------------------------------------------------------------8-40
CLEANING--------------------------------------------------------------------------------- 8-115
ENVRNT--------------------------------------------------------------------------------------8-40
FIXING-------------------------------------------------------------------------------------- 8-116
2D-SHADE-----------------------------------------------------------------------------------8-41
PANEL--------------------------------------------------------------------------------------- 8-116
I/O (I/O display mode)------------------------------------------------------------8-42
PART-CHK--------------------------------------------------------------------------------- 8-117
Host Machine_DC Controller (DC-CON>P001 to P030)-------------------------8-42
CLEAR-------------------------------------------------------------------------------------- 8-118
Host Machine_Main Controller (DC-CON>P001 to P005))----------------------8-51
MISC-R-------------------------------------------------------------------------------------- 8-120
Reader (R-CON>P001 to P005)--------------------------------------------------------8-51
MISC-P-------------------------------------------------------------------------------------- 8-124
ADF (FEEDER>P001 to P007)---------------------------------------------------------8-52
SENS-ADJ---------------------------------------------------------------------------------- 8-126
Paper Deck Unit - C1 (DC-CON>P048 to P050)-----------------------------------8-53
SYSTEM------------------------------------------------------------------------------------ 8-127
POD Deck Lite - A1 (DC-CON>P047 to P050)-------------------------------------8-54
2D-SHADE--------------------------------------------------------------------------------- 8-128
Inserter - K1 (DC-CON>P045 to P054)-----------------------------------------------8-55
Paper Folding Unit - H1 (DC-CON>P045 to P071)--------------------------------8-57
Professional Puncher - C1 + Integration Unit-B1

fineline6
 OPTION---------------------------------------------------------------------------- 8-130 FEEDER---------------------------------------------------------------------- 8-229
FNC-SW------------------------------------------------------------------------------------ 8-130 DISPLAY--------------------------------------------------------------------------- 8-229
DSPLY-SW--------------------------------------------------------------------------------- 8-137 ADJUST---------------------------------------------------------------------------- 8-230
IMG-FIX------------------------------------------------------------------------------------- 8-140 FUNCTION------------------------------------------------------------------------ 8-231
IMG-DEV------------------------------------------------------------------------------------ 8-143 OPTION---------------------------------------------------------------------------- 8-233
IMG-LSR------------------------------------------------------------------------------------ 8-146
SOATER---------------------------------------------------------------------- 8-234
IMG-RDR----------------------------------------------------------------------------------- 8-146
ADJUST---------------------------------------------------------------------------- 8-234
IMG-MCON--------------------------------------------------------------------------------- 8-148
FUNCTION------------------------------------------------------------------------ 8-242
CLEANING--------------------------------------------------------------------------------- 8-151
OPTION---------------------------------------------------------------------------- 8-244
ENV-SET------------------------------------------------------------------------------------ 8-152
FEED-SW----------------------------------------------------------------------------------- 8-153 BOARD----------------------------------------------------------------------- 8-247
NETWORK--------------------------------------------------------------------------------- 8-156 OPTION---------------------------------------------------------------------------- 8-247
CUSTOM----------------------------------------------------------------------------------- 8-164
USER---------------------------------------------------------------------------------------- 8-166 9 Installation
CST------------------------------------------------------------------------------------------ 8-178 Checking before Installation-------------------------------------------------9-2
ACC------------------------------------------------------------------------------------------ 8-180 Checking Power Supply----------------------------------------------------------- 9-2
INT-FACE----------------------------------------------------------------------------------- 8-182 Checking the Installation Environment---------------------------------------- 9-2
TEMPO-------------------------------------------------------------------------------------- 8-183 Checking Installation Space------------------------------------------------------ 9-2
LCNS-TR----------------------------------------------------------------------------------- 8-183
Points to Note at Installation Work--------------------------------------------- 9-3
TEST-------------------------------------------------------------------------------- 8-193
Table of Options Combination----------------------------------------------9-3
PG-------------------------------------------------------------------------------------------- 8-193
Order to Install the Host machine and the Options------------------------- 9-4
NETWORK--------------------------------------------------------------------------------- 8-194
Checking the Contents-------------------------------------------------------9-5
COUNTER------------------------------------------------------------------------- 8-196
TOTAL--------------------------------------------------------------------------------------- 8-196
Unpacking------------------------------------------------------------------------9-9
PICK-UP------------------------------------------------------------------------------------ 8-197 Installation--------------------------------------------------------------------- 9-11
FEEDER------------------------------------------------------------------------------------ 8-197 Installation of the Upright Control Panel------------------------------------- 9-11
JAM------------------------------------------------------------------------------------------ 8-198 Installing the Developing Assembly-------------------------------------------9-16
MISC----------------------------------------------------------------------------------------- 8-198 Installing the Pickup Assembly ------------------------------------------------9-20
JOB------------------------------------------------------------------------------------------- 8-199 Installing the Fixing Assembly--------------------------------------------------9-21
PRDC-1------------------------------------------------------------------------------------- 8-199 Installing the Toner Container---------------------------------------------------9-23
DRBL-1-------------------------------------------------------------------------------------- 8-201 Installing the Exhaust Filter------------------------------------------------------9-24
DRBL-2-------------------------------------------------------------------------------------- 8-205 Installing the USB Device Port (only with the products designed
T-CNTR------------------------------------------------------------------------------------- 8-223 for Europe) --------------------------------------------------------------------------9-25
SORTER------------------------------------------------------------------------------------ 8-223 Setting the Environment Heater Switch--------------------------------------9-28
Turning ON the Main Power----------------------------------------------------9-28
Turning OFF the Main Power---------------------------------------------------9-28
Toner Stirring------------------------------------------------------------------------9-29
Installation of the Host Machine------------------------------------------------9-29

fineline6
 Other Installation Work-----------------------------------------------------------9-29 Cassette Heater Unit-------------------------------------------------------- 9-54
Setting the Deck--------------------------------------------------------------------9-30 Checking the Contents (Asia only)--------------------------------------------9-54
Setting the Paper Cassette------------------------------------------------------9-32 Cassette Heater Unit-38------------------------------------------------------------------9-54
Auto Adjust Gradation------------------------------------------------------------9-33 Checking the Parts to be Installed (Europe only)--------------------------9-54
Image Position Adjustment------------------------------------------------------9-33 Check Items when Turning OFF the Main Power -------------------------9-54
Left Edge Margin Adjustment (1st side)-----------------------------------------------9-33 Installation Procedure-------------------------------------------------------------9-54
Adjusting margin of Multi-purpose Pickup Tray-------------------------------------9-35 Paper Deck Heater Unit-A1----------------------------------------------- 9-58
Left Edge Margin Adjustment (2nd side)----------------------------------------------9-36 Checking the Contents-----------------------------------------------------------9-58
Leading Edge Margin Adjustment (1st side)-----------------------------------------9-37 Check Items when Turning OFF the Main Power-------------------------9-58
Leading Edge Margin Adjustment (2nd side)----------------------------------------9-37 Installation Procedure (Paper Deck Unit-C1)-------------------------------9-59
Checking the Network Connection--------------------------------------------9-38 Utility Tray-A1----------------------------------------------------------------- 9-67
Overview--------------------------------------------------------------------------------------9-38
Checking the Contents-----------------------------------------------------------9-67
Checking the Network Connection-----------------------------------------------------9-38
Installation Procedure-------------------------------------------------------------9-68
Operation Procedure Using Ping-------------------------------------------------------9-38
When Installing the USB Keyboard-------------------------------------------9-69
Checking by the Remote Host Address-----------------------------------------------9-38
Network Troubleshooting--------------------------------------------------------9-39
Card Reader-C1-------------------------------------------------------------- 9-70
Points to Note at Installation----------------------------------------------------9-70
Checking Connection of the Network Cable-----------------------------------------9-39
Operation Procedure Using Ping-------------------------------------------------------9-39 Checking the Contents-----------------------------------------------------------9-70
Contents of Card Reader-C1------------------------------------------------------------9-70
Checking the Network Setting of the Host Machine----------------------9-39
Contents of Copy Card Reader Attachment-A2-------------------------------------9-71
Checking Network Function on the Main Controller----------------------9-39
Check Items when Turning OFF the Main Power -------------------------9-72
When Relocating the Machine-------------------------------------------- 9-40
Installation Procedure-------------------------------------------------------------9-72
Printer Cover -B1------------------------------------------------------------- 9-43
Setting After Installation----------------------------------------------------------9-77
Points to Note at Installation----------------------------------------------------9-43
Checking the Contents ----------------------------------------------------------9-43
Voice Guidance Kit-F1------------------------------------------------------ 9-78
Points to Note at Installation----------------------------------------------------9-78
Parts to be used----------------------------------------------------------------------------9-43
Parts not to be used-----------------------------------------------------------------------9-43 Checking the Contents-----------------------------------------------------------9-78
Check Items when Turning OFF the Main Power-------------------------9-44 Check Items when Turning OFF the Main Power-------------------------9-79
Installation Procedure-------------------------------------------------------------9-44 Installation Procedure-------------------------------------------------------------9-79
Operation Check-------------------------------------------------------------------9-47 Checking after Installation-------------------------------------------------------9-83
Auto Adjust Gradation------------------------------------------------------------9-47 Operation Check-------------------------------------------------------------------9-83
Reader Heater Unit---------------------------------------------------------- 9-48 Installation Procedure for Expansion Bus-F1,
Checking the Contents (ASIA only)-------------------------------------------9-48 IPSec Board-B2 and Wireless LAN Board-B1------------------------ 9-84
Reader Heater Unit-G1-------------------------------------------------------------------9-48 Points to Note at Installation----------------------------------------------------9-84
Checking the Parts to be Installed (Europe only)--------------------------9-48 Checking the Contents-----------------------------------------------------------9-85
Reader Heater Unit------------------------------------------------------------------------9-48 Expansion Bus-F1/F2---------------------------------------------------------------------9-85
Check Items when Turning OFF the Main Power-------------------------9-48 IPSec Board-B2-----------------------------------------------------------------------------9-85
Wireless LAN Board-B1-------------------------------------------------------------------9-86
Installation Procedule-------------------------------------------------------------9-49

fineline6
 Check Items when Turning OFF the Main Power-------------------------9-87 Points to Note Regarding Data Backup/Export-------------------------- 9-122
Installation Procedure-------------------------------------------------------------9-88 Making a Backup of the Data (Reference only)-------------------------- 9-123
Removing the Main Controller PCB 1-------------------------------------------------9-88 Check Items when Turning OFF the Main Power----------------------- 9-127
Installing the Expansion Bus-F1 and the IPSec Board-B2 Simultaneously-- 9-89 Installation Procedure----------------------------------------------------------- 9-127
Installing the Expansion Bus-F1, the Wireless LAN Board-B1 and Assembling the Option HDD----------------------------------------------------------- 9-127
the IPSec Board-B2 Simultaneously---------------------------------------------------9-90 Removing the HDD and HDD Case Unit------------------------------------------- 9-130
Checking after Installation-------------------------------------------------------9-95 Changing Configuration inside of HDD Case Unit------------------------------- 9-132
Additional Memory Type B (512MB)------------------------------------ 9-96 Installing the HDD Case Unit---------------------------------------------------------- 9-134
Checking the Contents-----------------------------------------------------------9-96 Installing the System Software Using the SST--------------------------- 9-137
Checking before Installation-----------------------------------------------------9-96 Execution of Auto Gradation Adjustment---------------------------------- 9-137
Check Items when Turning OFF the Main Power -------------------------9-96 [TYPE-4] Option HDD (80GB) + HDD Mirroring Kit or
Installation Procedure-------------------------------------------------------------9-96 HDD Data Encryption & Mirroring Kit--------------------------------- 9-138
Checking after Installation-------------------------------------------------------9-97 Points to Note when Unpacking HDD Data Encryption &
Combination of HDD Options--------------------------------------------- 9-98 Mirroring Kit----------------------------------------------------------------------- 9-138
[TYPE-1] Option HDD (250GB)------------------------------------------ 9-99 Checking the Contents--------------------------------------------------------- 9-138
Checking the Contents-----------------------------------------------------------9-99 Option HDD (80GB)---------------------------------------------------------------------- 9-138
Points to Note Regarding Data Backup/Export-------------------------- 9-100 HDD Mirroring Kit or HDD Data Encryption & Mirroring Kit-------------------- 9-139
Making a Backup of the Data (Reference only)-------------------------- 9-101 Points to Note when HDD Data Encryption &
Check Items when Turning OFF the Main Power----------------------- 9-105 Mirroring Kit has been Installed---------------------------------------------- 9-140
Assembling the Option HDD-------------------------------------------------- 9-105 Points to Note Regarding Data Backup/Export----------------------------------- 9-140
Procedure to Replace with the HDD---------------------------------------- 9-106 Making a Backup of the Data (Reference only)----------------------------------- 9-141
Installing the System Software Using the SST--------------------------- 9-108 Check Items when Turning OFF the Main Power----------------------- 9-145
Execution of Auto Gradation Adjustment---------------------------------- 9-108 Installation Procedure----------------------------------------------------------- 9-145
Removing the Covers------------------------------------------------------------------- 9-145
[TYPE-2] Removable HDD Kit------------------------------------------ 9-109
Installing the Mirroring Board or Encryption Board------------------------------- 9-147
Checking the Contents--------------------------------------------------------- 9-109
After Installing HDD Data Encryption & Mirroring Kit------------------- 9-157
Check Items when Turning OFF the Main Power----------------------- 9-110
Installing the System Software Using the SST------------------------------------ 9-157
Installation Procedure----------------------------------------------------------- 9-110
Checking the Security Version-------------------------------------------------------- 9-157
Removing the HDD and HDD Case Unit------------------------------------------- 9-110
Checking the Security Mark------------------------------------------------------------ 9-157
Disassembling and Assembling of the HDD Removed from
Setting for Mirroring------------------------------------------------------------- 9-158
the Host Machine------------------------------------------------------------------------- 9-113
After Installing HDD Data Encryption & Mirroring Kit------------------- 9-158
Changing Configuration inside of HDD Case Unit------------------------------- 9-115
Reporting to the System Administrator at the End of the Work--------------- 9-158
Installing the HDD Case Unit---------------------------------------------------------- 9-117
Execution of Auto Gradation Adjustment------------------------------------------- 9-158
[TYPE-3] Option HDD (250GB) + Removable HDD Kit---------- 9-120
Checking the Contents--------------------------------------------------------- 9-120
[TYPE-5] 2 Option HDDs (250GB) + HDD Mirroring Kit or
Option HDD (250GB)-------------------------------------------------------------------- 9-120 HDD Data Encryption & Mirroring Kit--------------------------------- 9-159
Removable HDD Kit--------------------------------------------------------------------- 9-121 Points to Note when Unpacking HDD Data Encryption &
Mirroring Kit----------------------------------------------------------------------- 9-159

fineline6
 Checking the Contents--------------------------------------------------------- 9-159 [TYPE-7] Option HDD (250GB) + HDD Data Encryption &
Option HDD (250GB)-------------------------------------------------------------------- 9-159 Mirroring Kit------------------------------------------------------------------ 9-197
HDD Mirroring Kit or HDD Data Encryption & Mirroring Kit-------------------- 9-160 Points to Note when Unpacking HDD Data Encryption &
Points to Note when HDD Data Encryption & Mirroring Kit----------------------------------------------------------------------- 9-197
Mirroring Kit has been Installed---------------------------------------------- 9-161 Checking the Contents--------------------------------------------------------- 9-197
Points to Note Regarding Data Backup/Export----------------------------------- 9-161 Option HDD (250GB)-------------------------------------------------------------------- 9-197
Making a Backup of the Data (Reference only)----------------------------------- 9-162 HDD Data Encryption & Mirroring Kit------------------------------------------------ 9-198
Check Items when Turning OFF the Main Power----------------------- 9-166 Points to Note Regarding Data Backup/Export-------------------------- 9-199
Installation Procedure----------------------------------------------------------- 9-166 Making a Backup of the Data (Reference only)-------------------------- 9-200
Assembling the Option HDD----------------------------------------------------------- 9-166 Check Items when Turning OFF the Main Power----------------------- 9-204
Removing the Covers------------------------------------------------------------------- 9-167 Installation Procedure----------------------------------------------------------- 9-204
Installing the Mirroring Board or Encryption Board------------------------------- 9-169 Assembling the Option HDD----------------------------------------------------------- 9-204
Installing the System Software Using the SST--------------------------- 9-178 Removing the Covers------------------------------------------------------------------- 9-205
After Installing HDD Data Encryption & Mirroring Kit------------------- 9-178 Installing the Encryption Board----------------------------------------------- 9-207
Checking the Security Version-------------------------------------------------------- 9-178 Installing the System Software Using the SST--------------------------- 9-215
Checking the Security Mark------------------------------------------------------------ 9-178
Checking the Security Version------------------------------------------------ 9-215
Setting for Mirroring------------------------------------------------------------- 9-179 Checking the Security Mark--------------------------------------------------- 9-215
Reporting to the System Administrator at the End of the Work (only Checking after Installation----------------------------------------------------- 9-216
when HDD Data Encryption & Mirroring Kit has been installed)----- 9-179 Reporting to the System Administrator at the End of the Work------ 9-216
Execution of Auto Gradation Adjustment---------------------------------- 9-179 Execution of Auto Gradation Adjustment---------------------------------- 9-216
[TYPE-6] HDD Data Encryption & Mirroring Kit-------------------- 9-180 [TYPE-8] Option HDD (80GB) + Removable HDD Kit +
Points to Note when HDD Data Encryption &
HDD Mirroring Kit or HDD Data Encryption & Mirroring Kit----- 9-217
Mirroring Kit has been Installed---------------------------------------------- 9-180 Points to Note when Unpacking HDD Data Encryption &
Checking the Contents--------------------------------------------------------- 9-180 Mirroring Kit----------------------------------------------------------------------- 9-217
Points to Note Regarding Data Backup/Export-------------------------- 9-181 Checking the Contents--------------------------------------------------------- 9-217
Making a Backup of the Data (Reference only)-------------------------- 9-182 Option HDD (80GB)---------------------------------------------------------------------- 9-217
Check Items when Turning OFF the Main Power----------------------- 9-186 Removable HDD Kit--------------------------------------------------------------------- 9-218
Installation Procedure----------------------------------------------------------- 9-186 HDD Mirroring Kit or HDD Data Encryption & Mirroring Kit-------------------- 9-219
Removing the Covers------------------------------------------------------------------- 9-186 Points to Note when HDD Data Encryption &
Installing the Encryption Board----------------------------------------------- 9-187 Mirroring Kit has been Installed---------------------------------------------- 9-220
Installing the System Software Using the SST--------------------------- 9-195 Points to Note Regarding Data Backup/Export----------------------------------- 9-220
Checking the Security Version------------------------------------------------ 9-195 Making a Backup of the Data (Reference only)----------------------------------- 9-221
Checking the Security Mark--------------------------------------------------- 9-195 Check Items when Turning OFF the Main Power----------------------- 9-225
Checking after Installation----------------------------------------------------- 9-196
Reporting to the System Administrator at the End of the Work------ 9-196
Execution of Auto Gradation Adjustment---------------------------------- 9-196

fineline6
 Installation Procedure----------------------------------------------------------- 9-225 Setting for Mirroring------------------------------------------------------------- 9-266
Removing the HDD and HDD Case Unit------------------------------------------- 9-225 Reporting to the System Administrator at the End of the Work (Only
Disassembling and Assembling of the HDD Removed from When HDD Data Encryption & Mirroring Kit has been Installed)---- 9-266
the Host Machine (the First HDD)---------------------------------------------------- 9-228 Execution of Auto Gradation Adjustment---------------------------------- 9-266
Assembling the Option HDD (the Second HDD)--------------------------------- 9-230
[TYPE-10] Removable HDD Kit + HDD Data Encryption &
Changing Configuration inside of HDD Case Unit------------------------------- 9-233
Mirroring Kit------------------------------------------------------------------ 9-267
Installing the Mirroring Board or Encryption Board and HDD Case Unit--- 9-234
Points to Note when Unpacking HDD Data Encryption &
After Installing HDD Data Encryption & Mirroring Kit------------------- 9-241
Mirroring Kit----------------------------------------------------------------------- 9-267
Installing the System Software Using the SST------------------------------------ 9-241
Checking the Contents--------------------------------------------------------- 9-267
Checking the Security Version-------------------------------------------------------- 9-241
Removable HDD Kit--------------------------------------------------------------------- 9-267
Checking the Security Mark------------------------------------------------------------ 9-241
HDD Data Encryption & Mirroring Kit------------------------------------------------ 9-268
Setting for Mirroring------------------------------------------------------------- 9-242
Points to Note Regarding Data Backup/Export-------------------------- 9-269
After Installing HDD Data Encryption & Mirroring Kit------------------- 9-242
Making a Backup of the Data (Reference only)-------------------------- 9-270
Reporting to the System Administrator at the End of the Work--------------- 9-242
Check Items when Turning OFF the Main Power----------------------- 9-274
Execution of Auto Gradation Adjustment------------------------------------------- 9-242
Installation Procedure----------------------------------------------------------- 9-274
[TYPE-9] 2 Option HDDs (250GB) + Removable HDD Kit +
Removing the HDD and HDD Case Unit------------------------------------------- 9-274
HDD Mirroring Kit or HDD Data Encryption & Mirroring Kit----- 9-243
Disassembling and Assembling of the HDD Removed from
Points to Note when HDD Data Encryption & Mirroring Kit has been
the Host Machine------------------------------------------------------------------------- 9-277
Installed---------------------------------------------------------------------------- 9-243
Changing Configuration inside of HDD Case Unit------------------------------- 9-280
Checking the Contents--------------------------------------------------------- 9-243 Installing the Encryption Board and HDD Case Unit---------------------------- 9-281
Option HDD (250GB)-------------------------------------------------------------------- 9-243
Installing the System Software Using the SST--------------------------- 9-288
Removable HDD Kit--------------------------------------------------------------------- 9-244
Checking the Security Version------------------------------------------------ 9-288
HDD Mirroring Kit or HDD Data Encryption & Mirroring Kit-------------------- 9-245
Checking the Security Mark--------------------------------------------------- 9-288
Points to Note when HDD Data Encryption &
Checking after Installation----------------------------------------------------- 9-289
Mirroring Kit has been Installed---------------------------------------------- 9-246
Reporting to the System Administrator at the End of the Work------ 9-289
Points to Note Regarding Data Backup/Export----------------------------------- 9-246
Execution of Auto Gradation Adjustment---------------------------------- 9-289
Making a Backup of the Data (Reference only)----------------------------------- 9-247
Check Items when Turning OFF the Main Power----------------------- 9-251 [TYPE-11] Option HDD (250GB) + Removable HDD Kit +
Installation Procedure----------------------------------------------------------- 9-251 HDD Data Encryption & Mirroring Kit--------------------------------- 9-290
Assembling the Option HDD----------------------------------------------------------- 9-251 Points to Note when Unpacking HDD Data Encryption &
Removing the HDD and HDD Case Unit------------------------------------------- 9-254 Mirroring Kit----------------------------------------------------------------------- 9-290
Changing Configuration inside of HDD Case Unit------------------------------- 9-257 Checking the Contents--------------------------------------------------------- 9-290
Installing the Mirroring Board or Encryption Board and HDD Case Unit--- 9-258 Option HDD (250GB)-------------------------------------------------------------------- 9-290
Installing the System Software Using the SST--------------------------- 9-265 Removable HDD Kit--------------------------------------------------------------------- 9-291
After Installing HDD Data Encryption & Mirroring Kit------------------- 9-265 HDD Data Encryption & Mirroring Kit------------------------------------------------ 9-292
Checking the Security Version-------------------------------------------------------- 9-265 Points to Note Regarding Data Backup/Export-------------------------- 9-293
Checking the Security Mark------------------------------------------------------------ 9-265 Making a Backup of the Data (Reference only)-------------------------- 9-294
Check Items when Turning OFF the Main Power----------------------- 9-298

fineline6
 Installation Procedure----------------------------------------------------------- 9-298 General Timing Chart------------------------------------------------------ 10-VI
Assembling the Option HDD----------------------------------------------------------- 9-298 Basic sequence at power ON--------------------------------------------------10-VI
Removing the HDD and HDD Case Unit------------------------------------------- 9-300 Basic sequence at printing
Changing Configuration inside of HDD Case Unit------------------------------- 9-303 <Condition: A4 1-sided (2 sheets), Right deck, Reverse delivery> 10-VII
Installing the Encryption Board and HDD Case Unit---------------------------- 9-304 Basic sequence at printing
Installing the System Software Using the SST--------------------------- 9-311 <Condition: A4 2-sided (2 sheets), Right deck, Reverse delivery> 10-VIII
Checking the Security Version------------------------------------------------ 9-311 General Circuit Diagram--------------------------------------------------- 10-IX
Checking the Security Mark--------------------------------------------------- 9-311 Signal Input/Output List---------------------------------------------------------10-IX
Checking after Installation----------------------------------------------------- 9-312 General Circuit Diagram--------------------------------------------------------10-XI
Reporting to the System Administrator at the End of the Work------ 9-312 General Circuit Diagram (1/30)--------------------------------------------------------10-XI
Execution of Auto Gradation Adjustment---------------------------------- 9-312 General Circuit Diagram (2/30)-------------------------------------------------------10-XII
HDD Data Encryption & Mirroring Kit-C2---------------------------- 9-313 General Circuit Diagram (3/30)------------------------------------------------------ 10-XIII
Points to Note at Installation-------------------------------------------------- 9-313 General Circuit Diagram (4/30)------------------------------------------------------10-XIV
Checking the Contents--------------------------------------------------------- 9-314 General Circuit Diagram (5/30)------------------------------------------------------ 10-XV
Check Items when Turning OFF the Main Power----------------------- 9-314 General Circuit Diagram (6/30)------------------------------------------------------10-XVI
In the Case of Fixed HDD----------------------------------------------------- 9-315 General Circuit Diagram (7/30)-----------------------------------------------------10-XVII
Assembling the Option HDD----------------------------------------------------------- 9-315 General Circuit Diagram (8/30)---------------------------------------------------- 10-XVIII
Removing the Covers------------------------------------------------------------------- 9-316 General Circuit Diagram (9/30)------------------------------------------------------10-XIX
Installing the Encryption Board-------------------------------------------------------- 9-318 General Circuit Diagram (10/30)----------------------------------------------------- 10-XX
Checking after Installation----------------------------------------------------- 9-328 General Circuit Diagram (11/30)-----------------------------------------------------10-XXI
General Circuit Diagram (12/30)----------------------------------------------------10-XXII
HDD Data Encryption & Mirroring Kit-C2 +
General Circuit Diagram (13/30)--------------------------------------------------- 10-XXIII
Removable HDD Kit ------------------------------------------------------ 9-329
General Circuit Diagram (14/30)---------------------------------------------------10-XXIV
Points to Note at Installation-------------------------------------------------- 9-329
General Circuit Diagram (15/30)--------------------------------------------------- 10-XXV
Checking the Contents--------------------------------------------------------- 9-330
General Circuit Diagram (16/30)---------------------------------------------------10-XXVI
Check Items when Turning OFF the Main Power----------------------- 9-330 General Circuit Diagram (17/30)--------------------------------------------------10-XXVII
In the Case of the Removable HDD----------------------------------------- 9-331 General Circuit Diagram (18/30)------------------------------------------------- 10-XXVIII
Removing the Fixed HDD/HDD Case Unit----------------------------------------- 9-331 General Circuit Diagram (19/30)---------------------------------------------------10-XXIX
Assembling the Removable HDD---------------------------------------------------- 9-333 General Circuit Diagram (20/30)--------------------------------------------------- 10-XXX
Changing Configuration inside of HDD Case Unit------------------------------- 9-336 General Circuit Diagram (21/30)---------------------------------------------------10-XXXI
Installing the Encryption Board/HDD Case Unit---------------------------------- 9-338 General Circuit Diagram (22/30)--------------------------------------------------10-XXXII
Checking after Installation----------------------------------------------------- 9-345 General Circuit Diagram (23/30)------------------------------------------------- 10-XXXIII
General Circuit Diagram (24/30)-------------------------------------------------10-XXXIV
Appendix General Circuit Diagram (25/30)------------------------------------------------- 10-XXXV
Service Tools------------------------------------------------------------------ 10-II General Circuit Diagram (26/30)-------------------------------------------------10-XXXVI
Special Tools------------------------------------------------------------------------10-II General Circuit Diagram (27/30)------------------------------------------------10-XXXVII
Solvents and Oils----------------------------------------------------------------- 10-V General Circuit Diagram (28/30)----------------------------------------------- 10-XXXVIII
General Circuit Diagram (29/30)-------------------------------------------------10-XXXIX

fineline6
 General Circuit Diagram (30/30)------------------------------------------------------10-XL 400 to 499----------------------------------------------------------------------------- 10-LXXIV
List of User Mode--------------------------------------------------------- 10-XLI 500 to 599------------------------------------------------------------------------------10-LXXV
Device Information Delivery Settings-------------------------------------- 10-XLI 600 to 699------------------------------------------------------------------------------10-LXXV
Environment Settings--------------------------------------------------------- 10-XLII 700 to 799------------------------------------------------------------------------------10-LXXV
Paper Settings--------------------------------------------------------------------------- 10-XLII 800 to 899----------------------------------------------------------------------------- 10-LXXVI
Display Settings------------------------------------------------------------------------- 10-XLII 900 to 999---------------------------------------------------------------------------- 10-LXXVII
Timer/Energy Settings---------------------------------------------------------------- 10-XLIII
Network---------------------------------------------------------------------------------- 10-XLIV
External Interface---------------------------------------------------------------------------10-L
Accessibility----------------------------------------------------------------------------------10-L
Adjustment/Maintenance-------------------------------------------------------- 10-LI
Adjust Image Quality*1-------------------------------------------------------------------- 10-LI
Adjust Action*1------------------------------------------------------------------------------ 10-LI
Maintenance-------------------------------------------------------------------------------- 10-LI
Function Settings---------------------------------------------------------------- 10-LII
Common------------------------------------------------------------------------------------ 10-LII
Copy*1---------------------------------------------------------------------------------------- 10-LV
Printer---------------------------------------------------------------------------------------- 10-LV
Send---------------------------------------------------------------------------------------- 10-LVI
Receive/Forward ----------------------------------------------------------------------- 10-LVII
Store/Access Files--------------------------------------------------------------------- 10-LVIII
Encrypted Secure Print---------------------------------------------------------------- 10-LIX
Set Destination-------------------------------------------------------------------10-LX
Set Destination---------------------------------------------------------------------------10-LX
Management Settings--------------------------------------------------------- 10-LXI
User Management----------------------------------------------------------------------- 10-LXI
Device Management-------------------------------------------------------------------- 10-LXI
License/Other--------------------------------------------------------------------------- 10-LXIII
Data Management--------------------------------------------------------------------- 10-LXIV
Backup Data--------------------------------------------------------------- 10-LXV
Detail of HDD partition------------------------------------------------- 10-LXIX
Soft Counter List--------------------------------------------------------- 10-LXX
Soft counter specifications---------------------------------------------------10-LXX
Soft Counter List---------------------------------------------------------------10-LXX
000 to 099--------------------------------------------------------------------------------10-LXX
100 to 199------------------------------------------------------------------------------- 10-LXXI
200 to 299------------------------------------------------------------------------------ 10-LXXII
300 to 399----------------------------------------------------------------------------- 10-LXXIII

fineline6
Main Unit PC cover A5.qxp 5/26/2010 12:04 PM Page 1

imageRUNNER ADVANCE
8105/8095/8085 Series

PARTS
CATALOG

May 19, 2010

Rev. 0

COPYRIGHT 2010 CANON INC. CANON imageRUNNER ADVANCE 8105/8095/8085 Series REV. 0 PRINTED IN U.S.A.
 PREFACE

This Parts Catalog contains listings of parts used

Diagrams are provided with the listings to aid the service technician in identifying clearly, the
item to be orderd.
Whenever ordering parts, consult this Parts Catalog for all of the information pertaining to each
item. Be sure to include, in the Parts Request, the full item description, the item part number,
and the quantity.

COPYRIGHT (C) 1999 CANON INC.

Use of this manual should be

strictly supervised to avoid
disclosure of confidential
information.
 Contents

NUMERICAL INDEX

imageRUNNER ADVANCE 8105/8095/8085 Series(Numerical Index) 1-1

imageRUNNER ADVANCE 8105/8095/8085 Series(Parts Catalog)

A1 ASSEMBLY LOCATION DIAGRAM ......................................2-1

A2 OPTION PARTS CATALOG LIST .........................................2-8
001 ACCESSOREIS .....................................................................2-9
100 EXTERNAL COVERS, PANELS, ETC. ...............................2-11
101 INTERNAL COMPONENTS 1 .............................................2-16
102 INTERNAL COMPONENTS 2 .............................................2-19
103 INTERNAL COMPONENTS 3 .............................................2-21
104 INTERNAL COMPONENTS 4 .............................................2-23
105 INTERNAL COMPONENTS 5 .............................................2-25
106 INTERNAL COMPONENTS 6 .............................................2-27
107 INTERNAL COMPONENTS 7 .............................................2-30
108 MACHINE BOTTOM PLATE ................................................2-32
109 MACHINE REAR PANEL 1 ..................................................2-33
110 MACHINE REAR PANEL 2 ..................................................2-35
111 MACHINE REAR PANEL 3 ..................................................2-37
112 FRONT COVER ASS'Y, LOWER ........................................2-39
113 RIGHT DOOR ASSEMBLY ..................................................2-41
114 VERTICAL PATH ASSEMBLY ............................................2-43
135 UPRIGHT CONTROL PANEL ASSEMBLY .........................2-44
136 CONTROL PANEL ARM ASSEMBLY .................................2-47
140 POWER CORD TERMINAL ASS'Y .....................................2-49
250 MAIN DRIVE ASS'Y .............................................................2-53
260 V. PATH/CST. PICK-UP ASS'Y ...........................................2-55
261 LEFT DECK PICK-UP DRIVE ASS'Y ..................................2-56
270 DRUM DRIVE ASS'Y ...........................................................2-58
271 DEVELOPING DRIVE ASS'Y ..............................................2-59
280 DELIVERY REVERSE DRIVE ASS'Y ..................................2-61
300 CASSETTE ASSEMBLY ......................................................2-62
301 CST. SIZE/REMNANT DETECT ASS'Y ..............................2-65
302 DECK REMNANT DETECT ASS'Y ......................................2-66
303 CASSETTE SIZE DETECT ASS'Y ......................................2-67
304 PAPER STOCK ASS'Y, RIGHT ...........................................2-68
305 PAPER STOCK ASS'Y, LEFT .............................................2-71
306 CASSETTE HEATER ASSEMBLY (JP) ..............................2-74
310 PAPER PICK-UP ASS'Y, RIGHT .........................................2-75
 Contents

311 PAPER PICK-UP ASS'Y, LEFT ...........................................2-78

312 MULTI TRAY ASS'Y ............................................................2-81
313 MULTI PAPER PICK-UP ASS'Y ..........................................2-83
315 PRE-REGISTRATION GUIDE ASS'Y ..................................2-86
330 FIXING/FEEDER DUPLEXING ASS'Y ................................2-87
331 FIXING/FEEDER FRAME ASS'Y .........................................2-93
332 REGISTRATION ASS'Y .......................................................2-97
333 DUPLEX. SIDE REG. SENSOR ASS'Y ...............................2-99
334 E.T.B. CLEANING ASSEMBLY .........................................2-100
335 E.T.BELT ASSEMBLY .......................................................2-102
336 REVERSE CROSSMEMBER ASS'Y, LF. ..........................2-104
350 OUTER PAPER DELIVERY ASS'Y ...................................2-106
351 REVERSE PAPER DELIVERY ASS'Y ...............................2-108
352 INNER PAPER DELIVERY ASS'Y .....................................2-112
460 LASER SCANNER UNIT ...................................................2-114
510 PHOTO-SENSITIVE DRUM ASSEMBLY ..........................2-115
550 1ST CORONA ASS'Y ........................................................2-117
570 PRE-TRANSFER CORONA ASS'Y ...................................2-119
620 HOPPER ASS'Y .................................................................2-121
625 BUFFER ASS'Y .................................................................2-123
640 DEVELOPING ASS'Y ........................................................2-125
650 DEVELOPING RELEASE ASS'Y .......................................2-127
710 AP. KIT ASS'Y ...................................................................2-129
711 DRUM CLEANING ASS'Y ..................................................2-133
720 SEPARATION CLAW DRIVE ASSEMBLY ........................2-135
770 WASTE TONER FEED ASSEMBLY ..................................2-137
810 FIXING ASS'Y ....................................................................2-140
811 FIXING ASS'Y, UPPER .....................................................2-142
812 FIXING DRIVE ASS'Y ........................................................2-147
813 FIXING ENTRANCE GUIDE ASS'Y ...................................2-149
814 FIXING EXIT GUIDE ASS'Y ..............................................2-150
900 CONTROLLER BOX ASSEMBLY .....................................2-151
910 IH POWER SUPPLY PCB ASS'Y ......................................2-153
920 INVERTER PCB ASSEMBLY ............................................2-154
930 DC CONTROLLER PCB ASS'Y .........................................2-155
931 MAIN CONTROLLER PCB ASS'Y, 1 .................................2-156
932 MAIN CONTROLLER PCB ASS'Y, 2 .................................2-157
960 MAIN DRIVE DRIVER PCB ASS'Y ....................................2-158
961 AC DRIVER PCB ASS'Y ....................................................2-159
962 NOISE FILTER PCB ASSEMBLY ......................................2-160
963 DUPLEXING DRIVER PCB ASSEMBLY ...........................2-161
964 FEED DRIVER PCB ASSEMBLY ......................................2-162
980 H.V. POWER SUPPLY ASS'Y ...........................................2-163
T40 DEVICE PORT ASSEMBLY (EUR) ...................................2-164
ZZA MECHANICAL STANDARD PARTS (HOW TO USE) .......2-165
 Contents

ZZB MECHANICAL STANDARD PARTS (SCREWS) ..............2-166

ZZC MECHANICAL STANDARD PARTS (BOLTS) ..................2-173
ZZD MECHANICAL STANDARD PARTS (NUTS) ....................2-174
ZZE MECHANICAL STANDARD PARTS (RETAINING RINGS) 2-175
Maintenance Guide

Please read this guide before operating this product.

After you finish reading this guide, store it in a safe place for future reference. ENG
imageRUNNER ADVANCE
8105/8095/8085
Maintenance Guide
 Manuals for the Machine
The manuals for this machine are divided as follows. Please refer to them for detailed information.

Guides with this symbol are included on the accompanying CD-ROM. (See footnote on the
Guides with this symbol are printed manuals. CD-ROM next page.)

Precautions for Using Your Machine and Settings Required after

Machine Installation Getting Started CD-ROM

Quick Reference for Basic and Useful Operations

Quick Reference CD-ROM

Maintenance and Troubleshooting

Maintenance Guide CD-ROM
(This Document)
Frequently Asked Questions and Answers
Frequently Asked Questions CD-ROM

Windows Printer Driver Installation and Instructions

Printer Driver Installation Guide CD-ROM

Mac Printer Driver Installation and Instructions

The Mac UFR II Driver Guide and the Mac PS Driver Guide
Mac Printer Driver Installation Guide CD-ROM

Windows Network ScanGear Installation and Instructions

Network ScanGear Installation Guide CD-ROM
 Comprehensive Manual for Basic Operations and Handling Your
Machine e-Manual CD-ROM

- Before You Start Using This Machine

- Basic Operations
- Optional Products/Software
- Settings/Registration
- Paper Type Management Settings
- Problem Solving
- Maintenance
- Practical Workflows
- Purpose Classified Links

- Copy
- Scan and Send
- Scan and Store
- Access Stored Files
- Fax/I-Fax Inbox
- Secured Print
- Hold
- Scanner
- Web Access
- Quick Menu
- Status Monitor/Cancel
- Print
- Network
- Remote UI
- MEAP
- Security

To view the manual in PDF format, Adobe Reader/Acrobat Reader/Acrobat is required. If Adobe Reader/Acrobat Reader/Acrobat is not installed on your system, please download it from the Adobe
Systems Incorporated website (https://www.adobe.com).