One-Way Slab & Stringers
One-Way Slab & Stringers
AND
STRINGERS
Reinforced concrete slabs are large flat plates that are supported at its sides by
reinforced concrete beams, walls, columns, steel beams, or by the ground. If a slab is
supported on two sides only, they are referred to a one-way slab since the bending
occurs in one direction only. If the slab is supported on all four sides, it is called two-way
slab since the bending occurs in both direction.
S L S L
<0.5 >2 <0.5 >2
L S L S
SLAB THICKNESS
According to NSCP 2010, Section 407.7.5, the flexural reinforcement shall not be
spaced further apart than 3 times the slab thickness, nor 450mm.
According to the code, one-way slabs, where flexural reinforcement extends in one
direction only should be reinforced for shrinkage and temperature stresses
perpendicular to flexural reinforcement.
Conditions before using the ACI Moment Coefficients: (NSCP 2010, Sec. 408.4.3)
wL ML MR
RL
2 L
For Reaction @ Right :
wL MR ML
RR
2 L
R R > RL
For slab spans less than 3 meters (Slab Spans < 3m)
STRINGERS
INFLUENCE LINES
All even # span: Negative Moment
Live Loads are transient loads
All odd # span: Positive Moment
PATTERN LOADING:
Load Case ( 1 )
Load Case ( 2 )
Load Case ( 3 )
DESIGN PROCEDURE
Where:
Mu fy
x= bd 2 ; m= 0.85 f ' c b = 1000mm (Considering 1m strip)
A
sreqd = g h ; where h = thickness of slab
1. Determine the required spacing of the main top bar at the first interior support of
the one-way slab below:
L1 L2
Given:
b = 300mm Slab t = 120mm
L1 = 3.2m fc = 25 MPa
L2 = 3.5m fy = Grade 40
DL = 4.8 kPa (inc. slab weight) Bar size = 10mm
LL = 1.9kPa
Solution:
2 2
8.8(3.05) 8.8(3.05)
Ext. face Mu = 12 = 6.823 kN-m ; Int. face Mu = 11 = 7.442 kN-m
95
276
x = 0.9(1000)(276) = 0.0033196 ; m= 0.85(25) = 12.988
7.442 x 106
1 12(0.0033196)(12.988)
reqd = 12.988 = 0.0033945
25 1.4
min = 4(276) = 0.0045290 or min = 276 = 0.0050725 ; min = 0.0050725
Since reqd < min , use = min [0.0050725 , 4/3(0.0033945)] , use = 0.0045260
10
2
sreqd = = 182.67mm
4
L1 = 2.5m
L2
L2 = 2.6m
L3
L3 = 2.7m
L4 = 2.8m
L4
CIEN 3454: Reinforced Concrete Design 1
1st Semester, AY: 2016-2017
Engr. Alberto S. Caete
ONE WAY SLAB AND STRINGERS
Lecture Notes
L5 = 6.4m
L6 = 7.6m
Girder Width = 350mm
Wall Load = 10 kN/m
Beam Wt = 4.32 kN/m
fc = 35 MPa
fy = Grade 60
1.5min
Floor DL = 6 kPa
Floor LL = 2.4 kPa
L5 L6
Solution:
Panel 2-5
2.6 2 2.6 2
DL w =
6 ( 2.6 ) [3
6.4( )]
= 7.371 kN/m LL w =
2.4 ( 2.6 ) [3 ( )
6.4
]
=
(3)(2) (3)(2)
2.948 kN/m
Panel 2-6
2.6 2 2.6 2
DL w =
6 ( 2.6 ) [3
7.6( )]
= 7.496 kN/m LL w =
2.4 ( 2.6 ) [3 ( )
7.6
]
=
(3)(2) (3)(2)
2.998 kN/m
Panel 3-5
2 2
2.7 2.7
DL w =
6 ( 2.7 ) [3
6.4( )
]
= 7.619 kN/m LL w =
2.4 ( 2.7 ) [3 ( )
6.4
]
=
(3)(2) (3)(2)
3.048 kN/m
Panel 3-6
2.7 2 2.7 2
DL w =
6 ( 2.7 ) [3
7.6( )]
= 7.759 kN/m LL w =
2.4 ( 2.7 ) [3 ( )
7.6
]
=
(3)(2) (3)(2)
3.104 kN/m
Ave. Ln = ( 6.4+7.6
2 )0.35 = 6.65m
For Span 5:
For Span 6:
45.253(6.65)2
Mu = 9 = 222.356 kN-m
35 1.4
min = 4(414) = 0.0035725 or min = 414 = 0.0033816 ; min = 0.0035725
= 1.5(0.0035725) = 0.0053588
( 0.0053588 ) ( 414 )
( 0.0053588 ) ( 414 ) [1 ]
R= 1.7 (35 ) = 2.1358 MPa
222.356 x 10
( 6)
bd2 = 0.9(2.1358) ; bd2 = 115.655 x106 mm3