SCHEDULE OF RATES FOR

ELE CT R ICAL IN STA LLA TIO N

WORKS IN SARAWAK 2014

JKR Sarawak
December 2014

Notes to tenderers:

1. This is only a cover page for this document. Please obtain the full set from the
JKR Sarawak webpage or any JKR Sarawak office.

2. The Location Factor from base at Kuching City for this tender is ____ %
and is the percentage over all the items and rates as listed in this Schedule of
Rates to be used for the purposes as stated in the tender documents.

3. Any attempt to amend / change / correct etc. this percentage by the

tenderer shall cause the tender to be disqualified.
 L O C AT I O N F AC T O R FR O M B A S E AT K U CH I N G CI T Y
(To be read together with the Rules of determining the Location Factor)

Kuching City 0% Sri Aman District 15%

Padawan 2% Lubok Antu 20%
Santubong 3% Lingga 20%
Siburan 3%
Pantu 13%
Bau 5%
Engkilili 18%
Lundu 8%
Skrang 15%
Sematan 9%

Sibu District 12%

Samarahan District 2%
Kem Bt 10 & 14 13%
Serian 5%
Durin 15%
Simunjan 12%
Bawang Assan 13%
Sebuyau 15%
Sungai Assan 13%
Asajaya 10%
Kanowit 16%
Sadong Jaya 12%
Machan 16%
Tebedu 8%
Nibong Tada 15%
Tebakang 8%
Nanga Tada 17%
Balai Ringin 8%
Nanga Dap 20%
Nanga Ngemah 20%
Betong District 20% Nanga Ngungun 20%
Spaoh 20% Nanga Poi 22%
Debak 20% Nanga Jagau 40%
Pusa 21% Selangau 18%
Beladin 20% Ulu Balingian 20%
Maludam 22% Arip 22%
Saratok 20% Stapang 16%
Roban 20% Rassau 22%
Kabong 20%

Kapit District 30% Bintulu District 15%

Song 25% Tatau 20%
Belaga 70% Sebauh 23%
Sungai Asap 25%
 L O C AT I O N F AC T O R FR O M B A S E AT K U CH I N G CI T Y
(To be read together with the Rules of determining the Location Factor)

Mukah District 20% Miri City 15%

Dalat 20% Subis 15%
Oya 20% Bekenu 15%
Igan 18% Marudi 25%
Balingian 23% Long Lama 40%
Kuala Balingian 23% Beluru 22%
Semop 30%
Matu 25%
Limbang District 30%
Betanak 30%
Lawas 28%
Daro 25%
Bruit 30%
Tanjung Manis 18%

Sarikei District 18%

Bintangor 18%
Pakan 20%
Selalang 20%
Julau 20%
Meluan 22%
Ulu Entabai 23%
Engkamop 30%
Nanga Wak 15%
Nanga Entabai 14%
 R U L E S O F DE T E R MI NI NG T H E L O C AT I O N FA C T O R

1. The % factors as stated are for those projects accessible by motorized vehicles within
15km radius from the location shown.

2. Where the project site is beyond 15km radius of the above stated locations, these
additional % factors shall be added on to those percentages stated above:

% addition

(i) > 15km < 45km 5%

( ii ) > 45km < 90km 10%
( iii ) > 90km < 135km 15%
( iv ) > 135km < 180km 20%
(v) > 180km < 220km 25%

3. Where the project sites are accessible only by waterway

(i) areas within 15 km radius 0%

( ii ) areas within 30 km radius 5%
( iii ) areas within 60 km radius 10%
( iv ) areas within 90 km radius 15%
(v) areas within 120 km radius 20%
( vi ) areas within 150 km radius 25%

4. Where the project sites can only be accessible by air, the location factor shall be doubled
over the value obtained from that by motorized vehicles.

5. Where the project sites can only be accessible by foot, the location factor shall be 50%
over the value obtained from that by authorized vehicles

6. Where in determining the locations factor and two or more factors and radial distances
are equally applicable, the lower in each case shall be used.

7. Where in determining the location factor and two or more factors and radial distances
by the rules above whereby there can be a combination due to accessibility, say partly
land and partly waterway or partly waterway and partly by foot, there shall be a
combination of the rules according to the radial distance from the nearest locations
stated above.

8. Where in determining the location factor and the Site for the project lies within two
more radial distances, the addition % for the radial distance within which more than
50% of the Site lies shall be used.
 P R E AM B L E S

1. All rates given shall include supply, delivery, installation, testing and
commissioning and shall include associated accessories and fitting.
2. Rate per point applies for the stated route length. For longer route length, the
rate per metre, derived from the rate per point shall be used.

3. All rates shall be used and read together with the Location Factor from base
at Kuching City.
4. All descriptions are to be read with reference to the Standard Electrical
Installation Specification (Latest Version) and the following :

a) All rates herein shall be held to include for supply and delivery to site, wastage on
materials, carriage and cartage, carrying in and return of empties, hoisting, setting,
fitting and fixing in position, making good and all other labours and everything else
necessary (including any custom duties, etc.) for the proper completion of each item and
for establishment charges and profit.

b) Rates for each item of paving shall be held to include for all rounded angles, arrises and
making good and any other sundry items of alike nature.

c) Rates for mild steel tubing are to include for short running lengths, sockets, backnuts,
elbows and bends.

SOR for Electrical Installation Works 2014

A GENERAL WIRING

Item Description Unit Rate (RM)

No.

Concealed conduit wiring c/w metal clad switch and socket plates
and accessories : Wiring shall be run concealed, in Class B
galvanized steel conduits and complete with GS conduit boxes let
into cement or timber wall, or partition, together with all necessary
metal clad lighting switch plates, switched socket plates, isolators
and accessories. Wiring shall be 1.5 mm2 PVC for fan and lighting
2
points, 2.5 mm PVC for 13A and 15A switched sockets. 13A 3-pin
switched socket points shall be wired in ring circuit/s. Accepted
brands Clipsal, PDL or MEM.

1 Lighting Point wired from nearest switch : Rate per point applies up to
route length of 10 metres.

(i) 6A 1-way lighting point c/w switch. Per point 102.20

(ii) 6A 2-way lighting point c/w switch. Per point 139.90

(iii) 6A intermediate lighting point c/w switch. Per point 161.40

2 Lighting Point wired from nearest lighting point (sharing same switch) up
to 4 metre route length.

(i) 6A 1-way lighting point. Per point 53.80

3 Fan Points : wired from nearest switch (up to 10 metres route length).

(i) Ceiling fan point c/w 6A switch. Per fan point 102.20

(ii) Extractor fan point c/w 6A switch. Cost excludes hard-wood frame and
opening for fan. Per fan point 102.20

4 Switched Socket Outlets :

(i) 13A 3-pin switched socket point in ring circuit : Per 1-gang 139.90
1 gang (up to 10 metre route length). socket pt.

(ii) 13A 3-pin switched socket point in ring circuit : Per 2-gang 188.30
2 gang (up to 10 metre route length). socket pt.

Per point 236.70

(iii) 15A 3-pin switched socket point (up to 15 metre route length).

5 Isolators and Water Heater Points : (up to 15 metre route length).

(i) Water heater point c/w 20A double pole switch with neon light indicator,
2
4mm PVC cable. Per point 269.00
2
(ii) 20A single phase isolator point 4 mm cabling. Per isolator 312.00
2
(iii) 30A single phase isolator point 6 mm cabling. Per isolator 430.40
2
(iv) 20A TPN isolator point 4 mm cabling. Per isolator 451.90
2
(v) 30A TPN isolator point 6 mm cabling. Per isolator
613.30

SOR ELEC 2014/Page 1 of 10

 '
A GENERAL WIRING...(CONT D)

Item
Description Unit Rate (RM)
No.

6 TV / Telephone Point : (up to 15 metre route length).

(i) 1 pair c/w socket and 2 x 0.63 mm cable. Per point 96.90
(ii) 2 pairs c/w socket and 4 x 0.63 mm cable. Per point 118.40

(iii) TV antennae point c/w 5c / 2v cable and TV socket. Per point 96.90

7 Miscellaneous Wiring Point : (up to 15 metre route length).

2
(i) Single phase power supply to fire protection control panel 2.5 mm PVC 231.30
cabling. Per point

(ii) 2 Per point

Lighting point for emergency lighting or keluar sign c/w 1.5 mm cable. 96.90

Surface conduit wiring c/w metal clad switch and socket plates and
accessories : Wiring shall be run on surface, in Class B galvanized
steel conduits and complete with GS conduit boxes, together with all
necessary metal clad lighting switch plates, switched socket plates,
isolators and accessories. Wiring shall be 1.5 mm PVC for fan and
lighting points, 2.5 mm PVC for 13A and 15A switched sockets. 13A
3-pin switched socket points shall be wired in ring circuit/s.
Accepted brands Clipsal, PDL or MEM.
8 Lighting Point wired from nearest switch : Rate per point applies up to

route length of 10 metres.

(i) 6A 1-way lighting point c/w switch. Per point 91.50

(ii) 6A 2-way lighting point c/w switch. Per point 134.50

(iii) 6A intermediate lighting point c/w switch. Per point 150.70

9 Lighting Point wired from nearest lighting point (sharing same switch)
up to 4 metre route length.

(i) 6A 1-way lighting point. Per point 48.50

10 Fan Points : wired from nearest switch (up to 10 metres route length) .

(i) Ceiling fan point c/w 6A switch. Per fan point 91.50

(ii) Extractor fan point c/w 6A switch. Cost excludes hard-wood frame and
opening for fan. Per fan point 91.50

11 Switched Socket Outlets :

(i) 13A 3-pin switched socket point in ring circuit : Per 1-gang 139.90
1 gang (up to 10 metre route length). socket pt.

(ii) 13A 3-pin switched socket point in ring circuit : Per 2-gang
2 gang (up to 10 metre route length). socket pt. 182.90

SOR ELEC 2014/Page 2 of 10

 '
A GENERAL WIRING...(CONT D)

Item
No. Description Unit Rate (RM)

'
11 Switched Socket Outlets : (Cont d)

(iii) 15A 3-pin switched socket point (up to 15 metre route length). Per point 193.70

12 Isolators and Water Heater Points : (up to 15 metre route length).

(i) Water heater point c/w 20A double pole switch with neon light indicator, 258.20
4mm PVC cable. Per point

2
(ii) 20A single phase isolator point 4 mm cabling. Per isolator 290.50
2
(iii) 30A single phase isolator point 6 mm cabling. Per isolator 392.70
2
(iv) 20A TPN isolator point 4 mm cabling. Per isolator 387.30

(v)
2
30A TPN isolator point 6 mm cabling. Per isolator 548.70

13 TV / Telephone Point : (up to 15 metre route length).

2 86.10
(i) 1 pair c/w socket and 2 x 0.63 mm cable. Per point

2
(ii) 2 pairs c/w socket and 4 x 0.63 mm cable. Per point 107.60

(iii) TV antennae point c/w 5c / 2v cable and TV socket. Per point 86.10

14 Miscellaneous Wiring Point : (up to 15 metre route length).

2
(i) Single phase power supply to fire protection control panel 2.5 mm PVC 215.20
cabling. Per point

2
(ii) Lighting point for emergency lighting or keluar sign c/w 1.5 mm cable. Per point 86.10

Surface Wiring : Wiring shall be run surface on batten wood

complete with all necessary PVC moulded conduit boxes, lighting
switch plates, 13A or 15A switched socket plates and accessories.
2 2
Wiring shall be 1.5 mm PVC/PVC for fan and lighting points, 2.5 mm
PVC/PVC for 13A and 15A switched sockets. 13A 3-pin switched
socket points shall be wired in ring circuit/s. Accepted brands
Clipsal, PDL or MEM.

15 Lighting Point wired from nearest switch : Rate per point applies up to

route length of 10 metres.

80.70
(i) 6A 1-way lighting point c/w switch. Per point

(ii) 6A 2-way lighting point c/w switch. Per point 118.40

(iii) 6A intermediate lighting point c/w switch. Per point 139.90

16 Lighting Point wired from nearest lighting point (sharing same switch) up
to 4 metre route length.
48.50
(i) 6A 1-way lighting point. Per point

SOR ELEC 2014/Page 3 of 10

 '
A GENERAL WIRING...(CONT D)

Item Description Unit Rate (RM)

No.

17 Fan Points : wired from nearest switch (up to 10 metres route length).

Ceiling fan point c/w 6A switch, ceiling rose and hardwood block for fan
(i)
speed regulator. Per fan point 80.70

(ii) Extractor fan point c/w 6A switch. (cost excludes hardwood frame and
opening for fan). Per fan point 80.70

18 Switched Socket Outlets and Water Heater Point :

(i) 13A 3-pin switched socket point in ring circuit : Per 1-gang 118.40
1 gang (up to 10 metre route length). socket pt.

(ii) 13A 3-pin switched socket point in ring circuit : Per 2-gang 161.40
2 gang (up to 10 metre route length). socket pt.

(iii) 15A 3-pin switched socket point (up to 15 metre route length). Per point
161.40

(iv) Water heater point c/w 20A double pole switch with neon light indicator, 4
mm PVC cable (up to 15 metre route length). Per point 226.00

19 Mains and Sub-mains Wiring : from SESCo supply intake to distribution

boards/consumer units, through meter and cut-outs, using surface wiring.
2
(i) 1-phase 2 x 16 mm 1 core PVC insulated and sheathed cables. Per metre 32.30

2
(ii) 1-phase 2 x 25 mm 1 core PVC insulated and sheathed cables. Per metre 43.10
2
(iii) 3-phase 4 x 16 mm 1 core PVC insulated and sheathed cables. Per metre 53.80
2
(iv) 3-phase 4 x 25 mm 1 core PVC insulated and sheathed cables. Per metre 75.40

Concealed conduit wiring c/w plastic moulded switch and socket

plates and accessories : Wiring shall be run concealed, in Class B
galvanized steel conduits and complete with GS conduit boxes let
into cement or timber wall, or partition, together with all necessary
PVC moulded lighting switch plates, switched socket plates and
accessories. Wiring shall be 1.5 mm PVC for fan and lighting points,
2.5 mm PVC for 13A and 15A switched sockets. 13A 3-pin switched
socket points shall be wired in ring circuit/s. Accepted brands
Clipsal, PDL or MEM.

Lighting Point wired from nearest switch : Rate per point applies up to
20

route length of 10 metres.

(i) Per point 96.90
6A 1-way lighting point c/w switch.

(ii) 6A 2-way lighting point c/w switch. Per point 134.50

(iii) 6A intermediate lighting point c/w switch. Per point 150.70

SOR ELEC 2014/Page 4 of 10

 '
A GENERAL WIRING...(CONT D)

Item Description Unit Rate (RM)

No.

21 Lighting Point wired from nearest lighting point (sharing same switch) up
to 4 metre route length.

(i) 6A 1-way lighting point. Per point 48.50

22 Fan Points : wired from nearest switch (up to 10 metres route length).

(i) Ceiling fan point c/w 6A switch. Per fan point 96.90

(ii) Extractor fan point c/w 6A switch. Cost excludes hard-wood frame and
opening for fan. Per fan point 96.90
23 Switched Socket Outlets :

(i) 13A 3-pin switched socket point in ring circuit : Per 1-gang 129.10
1 gang (up to 10 metre route length). socket pt.

(ii) 13A 3-pin switched socket point in ring circuit : Per 2-gang 172.20
2 gang (up to 10 metre route length). socket pt.

Per point 226.00

(iii) 15A 3-pin switched socket point (up to 15 metre route length).

24 TV / Telephone Point : (up to 15 metre route length).

(i) 1 pair c/w socket and 2 x 0.63 mm cable. Per point 86.10

(ii) 2 pairs c/w socket and 4 x 0.63 mm cable. Per point 107.60

(iii) TV antennae point c/w 5c / 2v cable and TV socket. Per point 86.10

25 Earthing Leads : from distribution board to earth electrode-green PVC

insulated copper cable protected by class 'B' galvanized steel conduits to
be installed below surface of hard-standing, cement floor, corridor, apron,
etc. (up to 10 metres route length)

(i)
2
16mm PVC insulated Per lot
269.00

(ii) 2
25mm PVC insulated Per lot 344.30

SOR ELEC 2014/Page 5 of 10

B LIGHTING FITTINGS, FANS AND ACCESSORIES

Item Description Unit Rate (RM)

No.

Accessories : Cost for extractor fan hole openings in brick or

wooden walls shall include cost of making the hole together with

2 x 4 hardwood frame. Size of opening shall be appropriate for the
diameter of fans indicated.

1 Installation of fan hook from cement floor slab. Per unit 34.50

2 Installation of fan hook from timber floor joist. Per unit 28.00

3 Extractor fan hole opening in brick wall for extractor fan of diameter from
400 to 500 mm (16 to 20). Per no. 209.80
4 Extractor fan hole opening in brick wall for extractor fan of diameter from
200 to 350 mm (8 to 14). Per no. 172.20
5 Extractor fan hole opening in wooden wall for extractor fan of diameter
from 400 to 500 mm (16 to 20). Per no. 142.10
6 Extractor fan hole opening in wooden wall for extractor fan of diameter
from 200 to 350 mm (8 to 14). Per no. 123.80
7 Extractor fan hole opening in glass panel for extractor fan of diameter from
200 to 350 mm (8 to 14). Per no.
158.20

Fans : Cost includes supply and installation of fittings. Ceiling fans

and oscillating fans shall have individual 3-speed (low/medium/high)
regulators. Wall fans shall feature pull cord oscillation control and 3-
speed (low/medium/high) regulators. Ceiling fans shall have safety
steel suspension wire and safe power disconnection feature. Cost of
making fan hole opening is priced separately. Acceptable brands
Khind, National, KDK or Sanyo

8 Ceiling fan 1,520 mm (60) diameter sweep. 175.40

Per unit

9 Ceiling mount oscillating fan 500 mm (20) dia. Per unit 349.70

10 Ceiling mount oscillating fan 400 mm (16) dia. Per unit 279.80

11 Wall mount fan 500 mm (20) diameter. Per unit 279.80

12 Wall mount fan 400 mm (16) diameter. Per unit 247.50

13 Extractor fan 500 mm (20) diameter. Per unit 279.80

14 Extractor fan 400 mm (16) diameter. Per unit 236.70

15 Extractor fan 350 mm (14) diameter. Per unit 204.40

16 Extractor fan 300 mm (12) diameter. Per unit 182.90

17 Extractor fan 200 mm (8) diameter.
Per unit 158.20

SOR ELECT 2014/Page 6 of 10

 '
B LIGHTING FITTINGS, FANS AND ACCESSORIES...(CONT D)

Item
Unit Rate (RM)
No. Description

Fluorescent Fittings : All fluorescent fittings shall be complete with

low loss polyester resin impregnated ballasts of loss not exceeding
6.5 watts, power factor correction capacitor to correct to power
factor of not less than 0.85, starter, fluorescent tubes and holders.
Cost includes supply and installation. Acceptable brands - LHL,
Britelite, Davis, Jetlite, National, GEC, Philip, Thorn.

18 Channel Fluorescent Fitting 1 x 18W / 36 W Surface Mount

(i) 1 x 18 watt bare channel fluorescent fitting. Per unit 33.40

(ii) 1 x 18 watt channel fluorescent fitting c/w wire guard. Per unit 61.40

(iii) 1 x 36 watt bare channel fluorescent fitting. Per unit 38.80

(iv) 1 x 36 watt bare channel fluorescent fitting c/w metal angle reflector. Per unit 73.20

(v) 1 x 36 watt bare channel fluorescent fitting c/w suspension rod. Per unit 78.60

(vi) 1 x 36 watt channel fluorescent fitting c/w wire guard. Per unit 67.80
(vii) 1 x 36 watt channel fluorescent fitting c/w wire guard and suspension rod. Per unit 96.90

19 Channel Fluorescent Fitting 2 x 36 W Surface Mount

(i) 2 x 36 watt bare channel fluorescent fitting. Per unit 67.80

(ii) 2 x 36 watt bare channel fluorescent fitting c/w suspension rod. Per unit 90.40

(iii) 2 x 36 watt channel fluorescent fitting c/w diakon diffuser. Per unit 101.20
(iv) 2 x 36 watt channel fluorescent fitting c/w diakon diffuser and suspension
rod. Per unit 123.80

(v) 2 x 36 watt bare channel fluorescent fitting c/w metal trough reflectors. Per unit 95.80

(vi) 2 x 36 watt bare channel fluorescent fitting c/w metal trough reflectors and
suspension rod. Per unit 129.10

20 Modular type Fluorescent Fittings Recessed Fittings

(i) 2 x 18 watt modular recessed (2 x 2) fluorescent fitting c/w aluminum

parabolic reflector and baffles. Per unit 158.20

(ii) 2 x 36 watt modular recessed (2 x 4) fluorescent fitting c/w aluminum

parabolic reflector and baffles. Per unit 191.50

(iii) 3 x 36 watt modular recessed (2 x 4) fluorescent fitting c/w aluminum

parabolic reflector and louvers. Per unit 231.30

SOR ELECT 2014/Page 7 of 10

 '
B LIGHTING FITTINGS, FANS AND ACCESSORIES...(CONT D)

Item Unit Rate (RM)

No. Description

21 Modular type Fluorescent Fittings Surface Fittings

(i) 2 x 18 watt modular recessed (2 x 2) fluorescent fitting c/w aluminum

parabolic reflector and baffles. Per unit 158.20

(ii) 2 x 36 watt modular surface (2 x 4) fluorescent fitting c/w aluminum

parabolic reflector and baffles. Per unit
191.50

(iii) 3 x 36 watt modular surface (2 x 4) fluorescent fitting c/w aluminum

parabolic reflector and louvers. Per unit 219.50

22 Self-contained Modular type Fluorescent Fittings c/w Battery & Charger

(i) 2 x 18 watt modular recessed (2 x 2) fluorescent fitting c/w aluminum

parabolic reflector and baffles, 3-hr maintenance free sealed lead-acid
battery, charger and control unit. Per unit 328.20
(ii) 2 x 36 watt modular recessed (2 x 4) fluorescent fitting c/w aluminum
parabolic reflector and baffles, 3-hr maintenance free sealed lead-acid
battery, charger and control unit. Per unit 406.70
(iii) 2 x 18 watt modular surface (2 x 2) fluorescent fitting c/w aluminum
parabolic reflector and baffles, 3-hr maintenance free sealed lead-acid
battery, charger and control unit. Per unit 327.10
(iv) 2 x 18 watt modular recessed (2 x 4) fluorescent fitting c/w aluminum
parabolic reflector and baffles, 3-hr maintenance free sealed lead-acid
battery, charger and control unit. Per unit 406.70

Miscellaneous Lighting Fittings : Cost includes supply and

installation of fittings. Installation for floodlight fittings are in
reference to standard installation on walls accessible by ladder.
Accepted brands for flood lights Nikkon, Thorn or Philips.

23 Emergency Light / KELUAR Sign Fittings : self contained c/w sealed 3-hr
maintenance free sealed lead-acid battery, charger and control unit c/w
trickle charging & over-charge protection.
123.80
(i) Self contained 2 x 8 watts emergency lighting fitting. Per unit

(ii) KELUAR sign fluorescent type, single sided. Per unit 180.80

(iii) KELUAR sign fluorescent type, double sided. Per unit 224.00

(iv) KELUAR c/w direction signage single sided fluorescent type. Per unit 186.20

(v) KELUAR c/w direction signage double sided fluorescent type. Per unit 236.70

(vi) KELUAR sign LED type, single sided. Per unit 186.20

(vii) KELUAR sign LED type, double sided. Per unit 196.90

(viii) KELUAR c/w direction signage single sided LED type. Per unit 203.40

(ix) KELUAR c/w direction signage double sided LED type.
Per unit 215.20

SOR ELECT 2014/Page 8 of 10

 '
B LIGHTING FITTINGS, FANS AND ACCESSORIES...(CONT D)

Item Rate (RM)

Description Unit
No.

24 Lamp-shade c/w incandescent lamp

(i) Coolicon lamp shade, lamp holder c/w 40W, 60W or 100 W incandescent
lamp. Per fitting 17.30

25 Flood-light / Spot-light Fittings

(i) Outdoor type spot light fitting c/w metal lamp holder and PAR 38 150 W
lamp of various colours. Per fitting 67.80

(ii) Outdoor type metal halide floodlight fittings c/w 400 W lamp, control gear
and power factor correction capacitor.
519.70
Per fitting

(iii) Outdoor type metal halide floodlight fittings c/w 250 W lamp, control gear
and power factor correction capacitor. Per fitting 451.90

(iv) Outdoor type high pressure sodium floodlight fittings c/w 400 W lamp,
control gear and power factor correction capacitor. Per fitting 542.20

(v) Outdoor type high pressure sodium floodlight fittings c/w 250 W lamp,
control gear and power factor correction capacitor. Per fitting 462.60

26 Bulkhead Fittings

(i) Bulkhead fitting pressure die-cast aluminium alloy type c/w 40W, 60W or
100W incandescent lamp, glass cover and wire guard. Per fitting 90.40

(ii) Bulkhead fitting plastic die-cast type c/w 40W, 60W or 100W
incandescent lamp, plastic cover and wire guard.
Per fitting 45.20

SOR ELECT 2014/Page 9 of 10

C DISTRIBUTION BOARDS & CONSUMER UNITS

Item Description Unit Rate (RM)

No.

Distribution Boards & Consumer Units : Distribution boards and

consumer units shall be metal clad type c/w isolator, residual current
circuit breaker (RCCB) and assortment of miniature circuit breakers
(mcb). Isolators and RCCB shall be double pole and four pole
respectively for single phase and three phase units. Isolators shall be
rated at 60A min. Miniature circuit breakers shall be single pole 6A,
15A, or 32A as required, of minimum breaking capacity 5 kA, and
tripping curve Type B. Comb-type busbars are not accepted. Units
shall feature DIN rail mounting, for plug-in, wired-out mcb. Accepted
brands MEM, Hager, L&T, LKH

1 Single Phase Consumer Units

(i) 4 way ( RCCB : 40A, 100 mA sensitivity). Per set 290.50

(ii) 4 way ( RCCB : 60A, 100 mA sensitivity). Per set 338.90

(iii) 6 way ( RCCB : 40A, 100 mA sensitivity). Per set 371.20

(iv) 6 way ( RCCB : 60A, 100 mA sensitivity). Per set 441.10

(v) 8 way ( RCCB : 40A, 100 mA sensitivity). Per set 441.10

(vi) 8 way ( RCCB : 60A, 100 mA sensitivity). Per set 494.90

2 Three Phase Distribution Boards c/w RCCB 100 mA sensitivity

(i) 4 way ( RCCB : 40A, 100 mA sensitivity). Per set 979.00

(ii) 4 way ( RCCB : 60A, 100 mA sensitivity). Per set 1,032.80

(iii) 6 way ( RCCB : 40A, 100 mA sensitivity). Per set 1,075.80

(iv) 6 way ( RCCB : 60A, 100 mA sensitivity). Per set 1,108.10

(v) 8 way ( RCCB : 40A, 100 mA sensitivity). Per set 1,253.40

(vi) 8 way ( RCCB : 60A, 100 mA sensitivity). Per set 1,377.10

3 Three Phase Distribution Boards c/w RCCB 300 mA sensitivity

(i) 4 way ( RCCB : 40A, 300 mA sensitivity). Per set 936.00

(ii) 4 way ( RCCB : 60A, 300 mA sensitivity). Per set 979.00

(iii) 6 way ( RCCB : 40A, 300 mA sensitivity). Per set 1,016.70

(iv) 6 way ( RCCB : 60A, 300 mA sensitivity). Per set 1,065.10

(v) 8 way ( RCCB : 40A, 300 mA sensitivity). Per set 1,215.70

(vi) 8 way ( RCCB : 60A, 300 mA sensitivity). Per set 1,301.80

SOR ELEC 2014/Page 10 of 10