Scribd Logo
Upload

Welcome to Scribd!

  • 184 views

    11 20 DM45spurhd Rev001

    Uploaded by

    whmidi7331
    The document provides step-by-step instructions for assembling an Atlas Copco DM30/45/L/ T4 Spur Rotary Head. It details 39 steps involving installing various components like bearings, seals, gears, spacers, and fasteners in the proper sequence and with recommended tools and techniques to ensure correct assembly. Safety precautions are also noted regarding heating components and installing parts.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    11 20 DM45spurhd Rev001

    Uploaded by

    whmidi7331
    184 views10 pages
    The document provides step-by-step instructions for assembling an Atlas Copco DM30/45/L/ T4 Spur Rotary Head. It details 39 steps involving installing various components like bearings, seals, gears, spacers, and fasteners in the proper sequence and with recommended tools and techniques to ensure correct assembly. Safety precautions are also noted regarding heating components and installing parts.

    Original Description:

    DM45

    Original Title

    11_20_DM45spurhd_rev001

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides step-by-step instructions for assembling an Atlas Copco DM30/45/L/ T4 Spur Rotary Head. It details 39 steps involving installing various components like bearings, seals, gears, spacers, and fasteners in the proper sequence and with recommended tools and techniques to ensure correct assembly. Safety precautions are also noted regarding heating components and installing parts.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    184 views10 pages

    11 20 DM45spurhd Rev001

    Uploaded by

    whmidi7331
    The document provides step-by-step instructions for assembling an Atlas Copco DM30/45/L/ T4 Spur Rotary Head. It details 39 steps involving installing various components like bearings, seals, gears, spacers, and fasteners in the proper sequence and with recommended tools and techniques to ensure correct assembly. Safety precautions are also noted regarding heating components and installing parts.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 10

    Atlas Copco Drilling Solutions DM30/45/L/ T4 Spur Rotary Head

    STEP 12

    12. Use protective gloves (57788093) to remove bearing cone from the heater and
    immediately slide bearing cone over the spindle until it rests on the bearing cone
    shoulder of the spindle. Allow time for the bearing cone to cool and shrink-fit onto
    the spindle. Once cooled, apply a coat of grease (item 119, 57818221) onto the
    bearing cone.

    STEP 13

    13. Ensure inside surface of the housing is free of dirt, metal shavings and other
    contaminants by blowing shop air pressure into the housing.

    Assembly/Rebuild Page 11 57788853


    Atlas Copco Drilling Solutions DM30/45/L/ T4 Spur Rotary Head

    STEP 14

    14. Install o-ring plugs (item 125, 95323465), pipe dope with plugs (item 18, 95033585)
    and magnetic drain plug (item 107, 50137256).

    STEP 15

    15. Install pipe sealant plug (item 67, 95249587). This is the port utilized for the
    magnetic sending unit with the rotary head option.

    STEP 16

    16. Install the cup of bearing (item 4, 95434551) evenly into the lower housing (item 8,
    57395444). Using a bronze drift (57788101), made from 1 square key stock and a
    rawhide hammer or a rubber mallet to tap the cup 90 degrees opposite side to evenly
    and fully seat the cup in the housing.

    Assembly/Rebuild Page 12 57788853


    Atlas Copco Drilling Solutions DM30/45/L/ T4 Spur Rotary Head

    STEP 17

    17. Use special tool tee-rod-hook (57788119) to pull the chain through the spindle with
    bearing cone attached.

    STEP 18

    18. Attach ring-lock tool (57788705) to chain hook for lifting the spindle.

    STEP 19

    19. Insert spindle with bearing (items 1 and 4) into lower bearing race.

    Assembly/Rebuild Page 13 57788853


    Atlas Copco Drilling Solutions DM30/45/L/ T4 Spur Rotary Head

    STEP 20

    20. Clean surface of lower seal housing (item2, 57578023), then install the first lower
    seal (item 3, 52146784) to keep oil in the housing and dirt out. Refer to oil seal design
    and selection for proper installation and function.

    STEP 21

    21. Use small steel hammer and bronze square head key stock (57788713), evenly seat
    the seal by tapping 90 degrees opposite sides. Then repeat for the second seal.

    STEP 22

    22. After fully seating the seal, use grease (item 119, 57818221) for lubricating both
    seals.

    Assembly/Rebuild Page 14 57788853


    Atlas Copco Drilling Solutions DM30/45/L/ T4 Spur Rotary Head

    STEP 23

    23. Use grease (item 119) to lubricate the spindle area prior to installing the lower seal.

    STEP 24
    24. Inject silicone (item 120, 50700731) onto the circumference surface of the lower
    housing to form a gasket prior to inserting the lower seal housing (57578023) with
    enclosed seals over the spindle. Care should be taken not to damage or distort the
    seals as they slip onto the spindle.

    STEP 25

    25. Align and insert screws and washers (items 5 & 6, 95934551 & 95934733) and
    tighten with socket-air ratchet.

    Assembly/Rebuild Page 15 57788853


    Atlas Copco Drilling Solutions DM30/45/L/ T4 Spur Rotary Head

    STEP 26
    26. Remove both eyebolts (57788069) from the rotary head stand, do not remove the
    upper half of the pillow block and BE CAREFUL, STAND AWAY when rotating
    the rotary head housing with top pointing upward. Re-insert both eyebolts into the
    stand.

    STEP 27
    27. Use the jack attached to the stand and the round plate (57788721) underneath the
    spindle so that the cup and cone of the lower bearing are pushed tightly together. The
    spindle must be supported tightly to ensure proper placement of the output gear.
    Remove the upper half of the pillow blocks during this process to observe shaft lift,
    which indicates the lower bearing cup, is fully seated, causing the rotary head
    assembly to lift.

    STEP 28

    28. Insert spacer (item 174, 57546319) over spindle.

    Assembly/Rebuild Page 16 57788853


    Atlas Copco Drilling Solutions DM30/45/L/ T4 Spur Rotary Head

    SHRINK FIT OUTPUT GEAR

    STEP 29

    29. Insert the custom key (item 11, 57546327) into the keyway in the spindle. Ensure the
    corners and edges of the key are clean, smooth and properly dressed to accept the
    output gear. The fit to the gear should be snug, but not interference fit. The key
    should be tightly fit within the groove, and should be fully seated against the bottom
    depth of the keyway, with contact surface to spacer (item 174). Insert the key with the
    threaded, jacking hole to the top as shown.

    STEP 30

    30. Insert 2 special threaded eyebolts and shackle (57788739 & 57788861) to lift the
    output gear (item 10, 57546301).

    Assembly/Rebuild Page 17 57788853


    Atlas Copco Drilling Solutions DM30/45/L/ T4 Spur Rotary Head

    STEP 31

    31. Measure the hub inside diameter on the output gear (item 10) including key height.
    Maximum diameter of the hub and keyway must not exceed 5.376. This will ensure
    that the output gear will fit over the key during installation.

    STEP 32

    32. Insert the output gear onto the induction heater or into an oil bath and heat to 430F.
    Ensure the gear is thoroughly heated. The fit to the spindle is a shrink fit up to 0.004.
    Binding problems may arise if the gear is not sufficiently heated.

    STEP 33

    33. With insulated gloves (57788093), remove the output gear from the induction heater
    and position the gear with the high-pressure grease hole to the top.

    Assembly/Rebuild Page 18 57788853


    Atlas Copco Drilling Solutions DM30/45/L/ T4 Spur Rotary Head

    STEP 34

    34. With the spindle supported and lower bearing properly seated in the bearing race,
    align the keyway, install the heated gear onto the spindle. The keyway should be flush
    to the key as shown. Care should be taken during gear installation not to damage the
    threads on the spindle.

    STEP 35

    35. Notice the position of the high-pressure grease hole to the top. After installation,
    allow the gear and spindle to cool for at least 1.5 hours to properly shrink fit to the
    shaft.

    STEP 36

    36. Install the 2nd spacer (item 174, 57546319) on top of the output gear.

    Assembly/Rebuild Page 19 57788853


    Atlas Copco Drilling Solutions DM30/45/L/ T4 Spur Rotary Head

    STEP 37

    37. Temporarily, install the retaining collar (item 176, 57546335) with a feeler gauge.
    Remove the retaining collar and spacer. Install shims (item 175, 57546384) in equal
    thickness to the gap measured. Reinstall the spacer and retaining collar.

    STEP 38

    38. Secure the retaining collar with cap screws (item 178, 95935235), flat washer (item
    179, 95922225) and lock nut (item 180, 95923371). There should be no gap
    remaining between the gear and the retaining collar. Peen the threads after inserting
    the lock nut.

    STEP 39

    39. Installation for locknuts are opposite and the air gun is used to clean the housing of
    metal shavings, dirt and other contaminates.

    Assembly/Rebuild Page 20 57788853

    You might also like