2008 Chevrolet Optra Manual en CA PDF

2008 Chevrolet Optra Owner Manual M
Seats and Restraint Systems ........................... 1-1 Driving Your Vehicle ....................................... 4-1
Front Seats ............................................... 1-2 Your Driving, the Road, and Your Vehicle ..... 4-2
Rear Seats ............................................... 1-8 Towing ................................................... 4-23
Safety Belts ............................................. 1-10 Service and Appearance Care .......................... 5-1
Child Restraints ....................................... 1-27 Service ..................................................... 5-4
Airbag System ......................................... 1-51 Fuel ......................................................... 5-6
Restraint System Check ............................ 1-66 Checking Things Under the Hood ............... 5-10
Features and Controls ..................................... 2-1 Headlamp Aiming ..................................... 5-40
Keys ........................................................ 2-2 Bulb Replacement .................................... 5-40
Doors and Locks ....................................... 2-6 Windshield Wiper Blade Replacement ......... 5-48
Windows ................................................. 2-11 Tires ...................................................... 5-49
Theft-Deterrent Systems ............................ 2-14 Appearance Care ..................................... 5-79
Starting and Operating Your Vehicle ........... 2-17 Vehicle Identification ................................. 5-87
Mirrors .................................................... 2-34 Electrical System ...................................... 5-88
Storage Areas ......................................... 2-36 Capacities and Specifications ..................... 5-94
Sunroof .................................................. 2-39 Maintenance Replacement Parts ................. 5-95
Instrument Panel ............................................. 3-1 Maintenance Schedule ..................................... 6-1
Instrument Panel Overview .......................... 3-4 Maintenance Schedule ................................ 6-2
Climate Controls ...................................... 3-19 Customer Assistance Information .................... 7-1
Warning Lights, Gages, and Indicators ........ 3-24 Customer Assistance and Information ........... 7-2
Audio System(s) ....................................... 3-41 Reporting Safety Defects ........................... 7-13
Vehicle Data Recording and Privacy ........... 7-16
Index ................................................................ 1
Canadian Owners
A French language copy of this manual can be obtained
from your dealer/retailer or from:
Helm, Incorporated
P.O. Box 07130
Detroit, MI 48207
GENERAL MOTORS, GM, the GM Emblem, 1-800-551-4123
CHEVROLET, the CHEVROLET Emblem, and the www.helminc.com
name OPTRA are registered trademarks of General
Motors Corporation. Propritaires Canadiens
This manual includes the latest information at the time it On peut obtenir un exemplaire de ce guide en franais
was printed. We reserve the right to make changes auprs de concessionnaire ou ladresse suivante:
after that time without further notice. For vehicles first Helm Incorporated
sold in Canada, substitute the name General Motors of P.O. Box 07130
Canada Limited for Chevrolet Motor Division whenever Detroit, MI 48207
it appears in this manual.
1-800-551-4123
This manual describes features that may be available in www.helminc.com
this model, but your vehicle may not have all of them.
For example, more than one entertainment system may
be offered or your vehicle may have been ordered
without a front passenger or rear seats.
Keep this manual in the vehicle for quick reference.
Litho in U.S.A.

Part No. 25810495 A First Print 2007 General Motors Corporation. All Rights Reserved.
ii
Using this Manual
Many people read the owner manual from beginning {CAUTION:
to end when they first receive their new vehicle to
learn about the vehicles features and controls. These mean there is something that could hurt
Pictures and words work together to explain things. you or other people.
Index We tell you what the hazard is and what to do to help

A good place to quickly locate information about the avoid or reduce the hazard. Please read these cautions.
vehicle is the Index in the back of the manual. It is If you do not, you or others could be hurt.
an alphabetical list of what is in the manual and
the page number where it can be found. A circle with a slash
through it is a safety
symbol which means
Safety Warnings and Symbols Do Not, Do Not do
this or Do Not let this
There are a number of safety cautions in this book.
happen.
A box with the word CAUTION is used to tell about
things that could hurt you or others if you were to ignore
the warning.
iii
Vehicle Damage Warnings Vehicle Symbols
You will also find notices in this manual. The vehicle has components and labels that use
symbols instead of text. Symbols are shown along with
Notice: These mean there is something that could the text describing the operation or information
damage your vehicle. relating to a specific component, control, message,
A notice tells about something that can damage the gage, or indicator.
vehicle. Many times, this damage would not be covered
by your vehicles warranty, and it could be costly.
The notice tells what to do to help avoid the damage.
When you read other manuals, you might see
CAUTION and NOTICE warnings in different colors or
in different words.
There are also warning labels on the vehicle which use
the same words, CAUTION or NOTICE.
iv
Section 1 Seats and Restraint Systems
Front Seats ......................................................1-2 Lower Anchors and Tethers for Children
Manual Seats (With Sliding Storage Tray) ..........1-2 (LATCH) ..................................................1-37
Manual Seats (Without Sliding Storage Tray) ......1-3 Securing a Child Restraint in a Rear
Driver Seat Tilt Adjuster ..................................1-4 Seat Position ............................................1-45
Manual Lumbar ..............................................1-4 Securing a Child Restraint in the Right Front
Reclining Seatbacks ........................................1-5 Seat Position ............................................1-48
Head Restraints .............................................1-7 Airbag System ...............................................1-51
Rear Seats .......................................................1-8 Where Are the Airbags? ................................1-54
Rear Seat Operation .......................................1-8 When Should an Airbag Inflate? .....................1-56
Safety Belts ...................................................1-10 What Makes an Airbag Inflate? .......................1-57
Safety Belts: They Are for Everyone ................1-10 How Does an Airbag Restrain? .......................1-57
How to Wear Safety Belts Properly .................1-15 What Will You See After an Airbag Inflates? .....1-58
Lap-Shoulder Belt .........................................1-23 Passenger Sensing System ............................1-59
Safety Belt Use During Pregnancy ..................1-26 Servicing Your Airbag-Equipped Vehicle ...........1-64
Safety Belt Extender .....................................1-26 Adding Equipment to Your Airbag-Equipped
Vehicle ....................................................1-64
Child Restraints .............................................1-27
Older Children ..............................................1-27 Restraint System Check ..................................1-66
Infants and Young Children ............................1-30 Checking the Restraint Systems ......................1-66
Child Restraint Systems .................................1-33 Replacing Restraint System Parts After
Where to Put the Restraint .............................1-36 a Crash ...................................................1-67
1-1
Front Seats Pull up and hold the lever
located under the front of
the seat to unlock it.
Manual Seats
(With Sliding Storage Tray)
{CAUTION:
You can lose control of the vehicle if you try to
adjust a manual drivers seat while the vehicle Slide the seat to where you want it and release the
is moving. The sudden movement could startle lever. Then try to move the seat with your body, to make
and confuse you, or make you push a pedal sure the seat is locked into place.
when you do not want to. Adjust the drivers
seat only when the vehicle is not moving.
If your vehicle has a sliding storage tray under the front

seat, the manual seat lever looks like this.
1-2
Manual Seats Pull up and hold the bar
located under the front of
(Without Sliding Storage Tray) the seat to unlock it.
{CAUTION:
adjust a manual drivers seat while the vehicle
is moving. The sudden movement could startle
and confuse you, or make you push a pedal
when you do not want to. Adjust the drivers Slide the seat to where you want it and release the bar.
seat only when the vehicle is not moving. Then try to move the seat with your body, to make
sure the seat is locked into place.
If your vehicle does not have a sliding storage tray

under the front seat, the manual seat bar looks like this.
1-3
Driver Seat Tilt Adjuster Manual Lumbar
Your vehicle may have manually operated lumbar
support for the drivers seat.
The manual drivers seat tilt adjuster knobs are located

on the outboard side of the seat cushion.
Turn the front knob to adjust the tilt of the front portion To adjust the front seat lumbar support, use the lever
of the seat cushion. Turn the rear knob to adjust the located on the outboard side of the seatback.
tilt of the rear portion of the seat cushion.
Push the lever down to adjust the support for the lower
part of the seatback. Pull the lever up to return the
support to its original position.
1-4
Reclining Seatbacks
{CAUTION:
adjust a manual drivers seat while the vehicle
is moving. The sudden movement could startle
and confuse you, or make you push a pedal
when you do not want to. Adjust the drivers
seat only when the vehicle is not moving.
The seats have manual reclining seatbacks. The lever

{CAUTION: used to operate them is located on the outboard side of
the seats.
If the seatback is not locked, it could move To recline the seatback:
forward in a sudden stop or crash. That could
1. Lift the recline lever.
cause injury to the person sitting there. Always
push and pull on the seatback to be sure it is 2. Move the seatback to the desired position, then
locked. release the lever to lock the seatback in place.
3. Push and pull on the seatback to make sure it
is locked.
1-5
To return the seatback to an upright position:
1. Lift the lever fully without applying pressure to the {CAUTION:
seatback and the seatback will return to the upright
position.
Sitting in a reclined position when your vehicle
2. Push and pull on the seatback to make sure it
is locked. is in motion can be dangerous. Even if you
buckle up, your safety belts cannot do their
job when you are reclined like this.
The shoulder belt cannot do its job because it
will not be against your body. Instead, it will be
in front of you. In a crash, you could go into it,
receiving neck or other injuries.
The lap belt cannot do its job either. In a
crash, the belt could go up over your
abdomen. The belt forces would be there,
not at your pelvic bones. This could cause
serious internal injuries.
For proper protection when the vehicle is in
motion, have the seatback upright. Then sit
well back in the seat and wear your safety belt
properly.
Do not have a seatback reclined if your vehicle is moving.
1-6
Head Restraints
Pull the head restraint up to raise it. To lower the

restraint, press the button, located on the top of the
seatback, and push the restraint down.
The rear seat head restraints may be adjustable and
work the same as the front head restraints.
Adjust the head restraint so that the top of the restraint
is at the same height as the top of the occupants The head restraints are removable. To remove a
head. This position reduces the chances of a neck injury restraint, press the button, located on the top of the
in a crash. seatback, and lift the head restraint from the guide
sleeve. Replace the head restraint before driving.
1-7
Rear Seats 3. Press the release
button located on top
of the rear seatback.
Rear Seat Operation
Your vehicle has rear seatbacks that can be folded
down to provide an extended cargo area.
To fold down the seatback, do the following:
Notice: Folding a rear seat with the safety belts
still fastened may cause damage to the seat or the
safety belts. Always unbuckle the safety belts
and return them to their normal stowed position 4. Fold the rear seatback forward and down.
before folding a rear seat.
1. Push the rear head restraints down completely.
2. Detach the safety belt in the rear center seat
position. Press the button in the buckle to release
the latch plate from the buckle.
1-8
To return the seatback to the upright position, do the
following:
{CAUTION:
{CAUTION: A safety belt that is improperly routed, not
properly attached, or twisted will not provide
If the seatback is not locked, it could move the protection needed in a crash. The person
forward in a sudden stop or crash. That could wearing the belt could be seriously injured.
cause injury to the person sitting there. Always After raising the rear seatback, always check
push and pull on the seatback to be sure it is to be sure that the safety belts are properly
locked. routed and attached, and are not twisted.
1. Lift the seatback up and push firmly on the top of 2. Make sure that the safety belts are not twisted or
the seatback until it latches securely in the fully caught under the seatback.
upright position. 3. Re-attach the rear center safety belt. Push the
latch plate at the end of the safety belt strap
into the buckle with the release button until the
mechanism clicks. Make sure the strap is not
twisted. The sliding latch plate should face the
front of the vehicle.
1-9
Safety Belts
{CAUTION:
Safety Belts: They Are for Everyone
It is extremely dangerous to ride in a cargo
This part of the manual tells you how to use safety area, inside or outside of a vehicle. In a
belts properly. It also tells you some things you should collision, people riding in these areas are more
not do with safety belts. likely to be seriously injured or killed. Do not
allow people to ride in any area of your vehicle
that is not equipped with seats and safety
{CAUTION: belts. Be sure everyone in your vehicle is in a
seat and using a safety belt properly.
Do not let anyone ride where he or she cannot
wear a safety belt properly. If you are in a Your vehicle has indicators as a reminder to buckle your
crash and you are not wearing a safety belt, safety belts. See Safety Belt Reminders on page 3-27.
your injuries can be much worse. You can hit In most states and in all Canadian provinces, the
things inside the vehicle harder or be ejected law requires wearing safety belts. Here is why:
from it and be seriously injured or killed. In the
You never know if you will be in a crash. If you do have
same crash, you might not be, if you are a crash, you do not know if it will be a serious one.
buckled up. Always fasten your safety belt,
A few crashes are mild, and some crashes can be so
and check that your passenger(s) are
serious that even buckled up, a person would not
restrained properly too. survive. But most crashes are in between. In many of
them, people who buckle up can survive and sometimes
walk away. Without belts they could have been badly
hurt or killed.
After more than 40 years of safety belts in vehicles,
the facts are clear. In most crashes buckling up does
matter... a lot!
1-10
Why Safety Belts Work
When you ride in or on anything, you go as fast as it goes.
Put someone on it.
Take the simplest vehicle. Suppose it is just a seat on

wheels.
1-11
Get it up to speed. Then stop the vehicle. The rider The person keeps going until stopped by something.
does not stop. In a real vehicle, it could be the windshield...
1-12
or the instrument panel... or the safety belts!
With safety belts, you slow down as the vehicle does.
You get more time to stop. You stop over more distance,
and your strongest bones take the forces. That is why
safety belts make such good sense.
1-13
Questions and Answers About Q: If I am a good driver, and I never drive far from
Safety Belts home, why should I wear safety belts?
Q: Will I be trapped in the vehicle after a crash if I A: You may be an excellent driver, but if you are in a
crash even one that is not your fault you and
am wearing a safety belt?
your passenger(s) can be hurt. Being a good
A: You could be whether you are wearing a safety driver does not protect you from things beyond your
belt or not. But your chance of being conscious control, such as bad drivers.
during and after an accident, so you can unbuckle Most accidents occur within 25 miles (40 km)
and get out, is much greater if you are belted. of home. And the greatest number of serious
And you can unbuckle a safety belt, even if you are injuries and deaths occur at speeds of less than
upside down. 40 mph (65 km/h).
Q: If my vehicle has airbags, why should I have to Safety belts are for everyone.
wear safety belts?
A: Airbags are supplemental systems only; so they
work with safety belts not instead of them.
Whether or not an airbag is provided, all occupants
still have to buckle up to get the most protection.
That is true not only in frontal collisions, but
especially in side and other collisions.
1-14
How to Wear Safety Belts Properly
This section is only for people of adult size.
Be aware that there are special things to know about
safety belts and children. And there are different
rules for smaller children and babies. If a child will be
riding in your vehicle, see Older Children on page 1-27
or Infants and Young Children on page 1-30. Follow
those rules for everyones protection.
It is very important for all occupants to buckle up.
Statistics show that unbelted people are hurt more often
in crashes than those who are wearing safety belts.
Occupants who are not buckled up can be thrown out of
the vehicle in a crash. And they can strike others in
the vehicle who are wearing safety belts.
First, before you or your passenger(s) wear a safety
belt, there is important information you should know.
Sit up straight and always keep your feet on the floor in
front of you. The lap part of the belt should be worn
low and snug on the hips, just touching the thighs. In a
crash, this applies force to the strong pelvic bones
and you would be less likely to slide under the lap belt.
If you slid under it, the belt would apply force on your
abdomen. This could cause serious or even fatal
injuries. The shoulder belt should go over the shoulder
and across the chest. These parts of the body are
best able to take belt restraining forces.
The shoulder belt locks if there is a sudden stop or crash.
1-15
Q: What is wrong with this?
{CAUTION:
You can be seriously hurt if your shoulder belt
is too loose. In a crash, you would move
forward too much, which could increase injury.
The shoulder belt should fit snugly against
your body.
A: The shoulder belt is too loose. It will not give as

much protection this way.
1-16
{CAUTION:
You can be seriously hurt if your lap belt is
too loose. In a crash, you could slide under the
lap belt and apply force on your abdomen.
This could cause serious or even fatal injuries.
The lap belt should be worn low and snug on
the hips, just touching the thighs.
A: The lap belt is too loose. It will not give nearly as

much protection this way.
1-17
{CAUTION:
You can be seriously injured if your belt is
buckled in the wrong place like this. In a crash,
the belt would go up over your abdomen.
The belt forces would be there, not on the
pelvic bones. This could cause serious internal
injuries. Always buckle your belt into the
buckle nearest you.
A: The belt is buckled in the wrong place.
1-18
{CAUTION:
You can be seriously injured if your belt goes
over an armrest like this. The belt would be
much too high. In a crash, you can slide under
the belt. The belt force would then be applied
on the abdomen, not on the pelvic bones, and
that could cause serious or fatal injuries.
Be sure the belt goes under the armrests.
A: The belt is over an armrest.
1-19
{CAUTION:
You can be seriously injured if you wear the
shoulder belt under your arm. In a crash, your
body would move too far forward, which would
increase the chance of head and neck injury.
Also, the belt would apply too much force to
the ribs, which are not as strong as shoulder
bones. You could also severely injure internal
organs like your liver or spleen. The shoulder
belt should go over the shoulder and across
the chest.
A: The shoulder belt is worn under the arm. It should

be worn over the shoulder at all times.
1-20
{CAUTION:
You can be seriously injured by not wearing
the lap-shoulder belt properly. In a crash,
you would not be restrained by the shoulder
belt. Your body could move too far forward
increasing the chance of head and neck injury.
You might also slide under the lap belt.
The belt force would then be applied right on
the abdomen. That could cause serious or fatal
injuries. The shoulder belt should go over the
shoulder and across the chest.
A: The belt is behind the body.
1-21
{CAUTION:
You can be seriously injured by a twisted belt.
In a crash, you would not have the full width of
the belt to spread impact forces. If a belt is
twisted, make it straight so it can work
properly, or ask your dealer/retailer to fix it.
A: The belt is twisted across the body.
1-22
Lap-Shoulder Belt
All seating positions in your vehicle have a
lap-shoulder belt.
If you are using a rear seating position with a detachable
safety belt and the safety belt is not attached, see
Rear Seat Operation on page 1-8 for instruction
on reconnecting the safety belt to the mini-buckle.
Here is how to wear a lap-shoulder belt properly.
1. Adjust the seat, if the seat is adjustable, so you can
sit up straight. To see how, see Seats in the Index.
2. Pick up the latch plate and pull the belt across you.
Do not let it get twisted.
The lap-shoulder belt may lock if you pull the belt
across you very quickly. If this happens, let the belt 3. Push the latch plate into the buckle until it clicks.
go back slightly to unlock it. Then pull the belt If you find that the latch plate will not go fully into
across you more slowly. the buckle, see if you are using the correct buckle.
If you ever pull the shoulder portion of a passenger 4. Pull up on the latch plate to make sure it is secure.
belt out all the way, you may engage the child If the belt is not long enough, see Safety Belt
restraint locking feature. If this happens, just let the Extender on page 1-26.
belt go back all the way and start again.
Make sure the release button on the buckle is
positioned so you would be able to unbuckle the
safety belt quickly if necessary.
1-23
5. If equipped with a shoulder belt height adjuster,
move it to the height that is right for you. Improper
shoulder belt height adjustment could reduce
the effectiveness of the safety belt in a crash.
See Shoulder Belt Height Adjustment later in this
section.
To unlatch the belt, push the button on the buckle.

The belt should go back out of the way.
Before you close a door, be sure the belt is out of the
way. If you slam the door on it, you can damage
both the belt and your vehicle.
6. To make the lap part tight, pull up on the

shoulder belt.
It may be necessary to pull stitching on the safety
belt through the latch plate to fully tighten the
lap belt on smaller occupants.
1-24
Shoulder Belt Height Adjuster Safety Belt Pretensioners
Your vehicle has a shoulder belt height adjuster for the Your vehicle has safety belt pretensioners for front
driver and right front passenger. outboard occupants. Although you cannot see them,
Adjust the height so that the shoulder portion of the belt they are part of the safety belt assembly. They can help
is centered on your shoulder. The belt should be tighten the safety belts during the early stages of a
moderate to severe frontal or near frontal crash if the
away from your face and neck, but not falling off your
shoulder. Improper shoulder belt height adjustment threshold conditions for pretensioner activation are met.
could reduce the effectiveness of the safety belt Pretensioners work only once. If they activate in a
in a crash. crash, you will need to get new ones, and probably other
new parts for your safety belt system. See Replacing
To move it down, press
Restraint System Parts After a Crash on page 1-67.
the release button (A) and
move the height adjuster
to the desired position.
After you move the height adjuster to where you want it,
try to move it down without pressing the release
button to make sure it has locked into position.
1-25
Safety Belt Use During Pregnancy Safety Belt Extender
Safety belts work for everyone, including pregnant If the vehicles safety belt will fasten around you,
women. Like all occupants, they are more likely to be you should use it.
seriously injured if they do not wear safety belts.
But if a safety belt is not long enough, your dealer/
retailer will order you an extender. When you go in to
order it, take the heaviest coat you will wear, so the
extender will be long enough for you. To help avoid
personal injury, do not let someone else use it, and use
it only for the seat it is made to fit. The extender has
been designed for adults. Never use it for securing child
seats. To wear it, attach it to the regular safety belt.
For more information, see the instruction sheet
that comes with the extender.
A pregnant woman should wear a lap-shoulder belt,

and the lap portion should be worn as low as possible,
below the rounding, throughout the pregnancy.
The best way to protect the fetus is to protect the
mother. When a safety belt is worn properly, it is
more likely that the fetus will not be hurt in a crash.
For pregnant women, as for anyone, the key to making
safety belts effective is wearing them properly.
1-26
Child Restraints The manufacturers instructions that come with the
booster seat, state the weight and height limitations for
that booster. Use a booster seat with a lap-shoulder
Older Children belt until the child passes the below fit test:
Sit all the way back on the seat. Do the knees bend
at the seat edge? If yes, continue. If no, return to
the booster seat.
Buckle the lap-shoulder belt. Does the shoulder belt
rest on the shoulder? If yes, continue. If no, then
return to the booster seat.
Does the lap belt fit low and snug on the hips,
touching the thighs? If yes, continue. If no, return to
the booster seat.
Can proper safety belt fit be maintained for the
length of the trip? If yes, continue. If no, return
to the booster seat.
Older children who have outgrown booster seats should

wear the vehicles safety belts.
1-27
Q: What is the proper way to wear safety belts?
A: An older child should wear a lap-shoulder belt and {CAUTION:
get the additional restraint a shoulder belt can
provide. The shoulder belt should not cross the face Never do this.
or neck. The lap belt should fit snugly below the
Here two children are wearing the same belt.
hips, just touching the top of the thighs. This applies
The belt cannot properly spread the impact
belt force to the childs pelvic bones in a crash.
It should never be worn over the abdomen, which forces. In a crash, the two children can be
could cause severe or even fatal internal injuries crushed together and seriously injured. A belt
in a crash. must be used by only one person at a time.
According to accident statistics, children and infants

are safer when properly restrained in the rear seating
positions than in the front seating positions.
In a crash, children who are not buckled up can strike
other people who are buckled up, or can be thrown
out of the vehicle. Older children need to use safety
belts properly.
1-28
{CAUTION:
Never do this.
Here a child is sitting in a seat that has a
lap-shoulder belt, but the shoulder part is
behind the child. In a crash, the child would
not be restrained by the shoulder belt.
The child might slide under the lap belt.
The belt force would then be applied right on
the abdomen. That could cause serious or fatal
injuries. The child could also move too far
forward increasing the chance of head and
neck injury. The shoulder belt should go over
the shoulder and across the chest.
1-29
Infants and Young Children Every time infants and young children ride in vehicles,
they should have the protection provided by appropriate
Everyone in a vehicle needs protection! This includes restraints. Children who are not restrained properly
infants and all other children. Neither the distance can strike other people, or can be thrown out of
traveled nor the age and size of the traveler changes the vehicle. In addition, young children should not use
the need, for everyone, to use safety restraints. In fact, the vehicles adult safety belts alone; they need to
the law in every state in the United States and in use a child restraint.
every Canadian province says children up to some age
must be restrained while in a vehicle.
{CAUTION:
{CAUTION: People should never hold an infant in their
arms while riding in a vehicle. An infant does
Children can be seriously injured or strangled not weigh much until a crash. During a
if a shoulder belt is wrapped around their crash an infant will become so heavy it is not
neck and the safety belt continues to tighten. possible to hold it. For example, in a crash at
Never leave children unattended in a vehicle only 25 mph (40 km/h), a 12 lb (5.5 kg) infant
and never allow children to play with the will suddenly become a 240 lb (110 kg) force
safety belts. on a persons arms. An infant should be
secured in an appropriate restraint.
1-30
CAUTION: (Continued)
children, but not for young children and

infants. Neither the vehicles safety belt system
nor its airbag system is designed for them.
Young children and infants need the protection
that a child restraint system can provide.
{CAUTION:
Children who are up against, or very close to,
any airbag when it inflates can be seriously
injured or killed. Airbags plus lap-shoulder
belts offer protection for adults and older
1-31
Q: What are the different types of add-on child
restraints? {CAUTION:
A: Add-on child restraints, which are purchased by the
vehicles owner, are available in four basic types. Newborn infants need complete support,
Selection of a particular restraint should take including support for the head and neck.
into consideration not only the childs weight, height, This is necessary because a newborn infants
and age but also whether or not the restraint will neck is weak and its head weighs so much
be compatible with the motor vehicle in which it will compared with the rest of its body. In a crash,
be used. an infant in a rear-facing seat settles into
For most basic types of child restraints, there are the restraint, so the crash forces can be
many different models available. When purchasing a distributed across the strongest part of an
child restraint, be sure it is designed to be used infants body, the back and shoulders. Infants
in a motor vehicle. If it is, the restraint will have a should always be secured in appropriate infant
label saying that it meets federal motor vehicle restraints.
safety standards.
The restraint manufacturers instructions that come
with the restraint state the weight and height
limitations for a particular child restraint. In addition,
there are many kinds of restraints available for
children with special needs.
1-32
Child Restraint Systems
{CAUTION: A rear-facing infant
seat (A) provides restraint
The body structure of a young child is quite with the seating surface
unlike that of an adult or older child, for whom against the back of
the safety belts are designed. A young childs the infant.
hip bones are still so small that the vehicles
regular safety belt may not remain low on the
hip bones, as it should. Instead, it may settle
up around the childs abdomen. In a crash,
the belt would apply force on a body area
that is unprotected by any bony structure.
This alone could cause serious or fatal The harness system holds the infant in place and,
injuries. Young children should always be in a crash, acts to keep the infant positioned in
secured in appropriate child restraints. the restraint.
A forward-facing child
seat (B) provides restraint
for the childs body
with the harness.
1-33
Securing an Add-On Child Restraint
in the Vehicle
{CAUTION:
A child can be seriously injured or killed in a
crash if the child restraint is not properly
secured in the vehicle. Make sure the child
restraint is properly installed in the vehicle
using the vehicles safety belt or LATCH
system, following the instructions that came
with that restraint, and also the instructions in
this manual.
A booster seat (C-D) is a child restraint designed to
improve the fit of the vehicles safety belt system.
A booster seat can also help a child to see out the To help reduce the chance of injury, the child restraint
window. must be secured in the vehicle. Child restraint systems
must be secured in vehicle seats by lap belts or the
lap belt portion of a lap-shoulder belt, or by the LATCH
system.
1-34
See Lower Anchors and Tethers for Children (LATCH) Securing the Child Within the
on page 1-37 for more information. A child can be
endangered in a crash if the child restraint is not Child Restraint
properly secured in the vehicle.
When securing an add-on child restraint, refer to the
instructions that come with the restraint which may be on {CAUTION:
the restraint itself or in a booklet, or both, and to this
manual. The child restraint instructions are important, A child can be seriously injured or killed in a
so if they are not available, obtain a replacement crash if the child is not properly secured in
copy from the manufacturer. the child restraint. Because there are different
Keep in mind that an unsecured child restraint can systems, it is important to refer to the
move around in a collision or sudden stop and injure instructions that come with the restraint. Make
people in the vehicle. Be sure to properly secure sure the child is properly secured, following
any child restraint in your vehicle even when no the instructions that came with that restraint.
child is in it.
1-35
Where to Put the Restraint
Accident statistics show that children are safer if they {CAUTION:
are restrained in the rear rather than the front seat.
We recommend that children and child restraints A child in a rear-facing child restraint can be
be secured in a rear seat, including: an infant or a child seriously injured or killed if the right front
riding in a rear-facing child restraint; a child riding in passengers airbag inflates. This is because
a forward-facing child seat; an older child riding in the back of the rear-facing child restraint
a booster seat; and children, who are large enough, would be very close to the inflating airbag.
using safety belts.
Even though the passenger sensing system is
A label on your sun visor says, Never put a rear-facing designed to turn off the right front passengers
child seat in the front. This is because the risk to the frontal airbag if the system detects a rear-facing
rear-facing child is so great, if the airbag deploys.
child restraint, no system is fail-safe, and no
one can guarantee that an airbag will not deploy
under some unusual circumstance, even
though it is turned off. We recommend that
rear-facing child restraints be secured in a rear
seat, even if the airbag is off.
If you secure a forward-facing child restraint in
the right front seat, always move the front
passenger seat as far back as it will go. It is
better to secure the child restraint in a rear seat.
See Passenger Sensing System on page 1-59
for additional information.
1-36
When securing a child restraint in a rear seating Make sure that a LATCH-compatible child restraint is
position, study the instructions that came with your child properly installed using the anchors, or use the vehicles
restraint to make sure it is compatible with this vehicle. safety belts to secure the restraint, following the
instructions that came with that restraint, and also the
Wherever you install a child restraint, be sure to
instructions in this manual. When installing a child
secure the child restraint properly.
restraint with a top tether, you must also use either the
Keep in mind that an unsecured child restraint can lower anchors or the safety belts to properly secure
move around in a collision or sudden stop and injure the child restraint. A child restraint must never be
people in the vehicle. Be sure to properly secure installed using only the top tether and anchor.
any child restraint in your vehicle even when no
In order to use the LATCH system in your vehicle, you
child is in it.
need a child restraint that has LATCH attachments.
The child restraint manufacturer will provide you
Lower Anchors and Tethers for with instructions on how to use the child restraint and its
attachments. The following explains how to attach a
Children (LATCH) child restraint with these attachments in your vehicle.
The LATCH system holds a child restraint during driving Not all vehicle seating positions or child restraints have
or in a crash. This system is designed to make lower anchors and attachments or top tether anchors
installation of a child restraint easier. The LATCH and attachments.
system uses anchors in the vehicle and attachments
on the child restraint that are made for use with
the LATCH system.
1-37
Lower Anchors Top Tether Anchor
Lower anchors (A) are metal bars built into the vehicle. A top tether (A, C) anchors the top of the child restraint
There are two lower anchors for each LATCH seating to the vehicle. A top tether anchor is built into the
position that will accommodate a child restraint with vehicle. The top tether attachment (B) on the child
lower attachments (B). restraint connects to the top tether anchor in the vehicle
in order to reduce the forward movement and rotation
of the child restraint during driving or in a crash.
Your child restraint may have a single tether (A) or a
dual tether (C). Either will have a single attachment (B)
to secure the top tether to the anchor.
1-38
Some child restraints that have a top tether are designed To assist you in locating
for use with or without the top tether being attached. the lower anchors, each
Others require the top tether always to be attached. seating position with lower
In Canada, the law requires that forward-facing anchors has two labels,
child restraints have a top tether, and that the tether be near the crease between
attached. Be sure to read and follow the instructions the seatback and the
for your child restraint. seat cushion.
If the child restraint does not have a top tether, one can
be obtained, in kit form, for many child restraints.
Ask the child restraint manufacturer whether or not a
kit is available.
Lower Anchor and Top Tether Anchor To assist you in locating

Locations the top tether anchors,
the top tether anchor
i (Top Tether Anchor): symbol is located on the
Seating positions with cover, if there is a cover.
top tether anchors.
j (Lower Anchor):
Seating positions with
two lower anchors.
Rear Seat
1-39
Hatchback Wagon Outside Positions
For hatchback models, the top tether anchors (B) are For outside seating positions in a wagon model, the top
located under covers in the rear cargo area, attached tether anchors (A) are exposed anchors, located behind
to the back wall (A) of the vehicle. Squeeze and pull the rear seat, on the floor of the rear cargo area (B).
the front part of the cover to access the anchors. Be sure to use an anchor located on the same side of
Remove the cargo shade before installing the top tether. the vehicle as the seating position where the child
The cargo shade should remain off while the top tether restraint will be placed.
anchor is in use. Be sure to use an anchor located
on the same side of the vehicle as the seating position
where the child restraint will be placed.
1-40
Do not secure a child restraint in a position without a
top tether anchor if a national or local law requires that
the top tether be attached, or if the instructions that
come with the child restraint say that the top tether
must be attached.
Accident statistics show that children are safer if they
are restrained in the rear rather than the front seat.
See Where to Put the Restraint on page 1-36 for
additional information.
Wagon Center Position
For the center position in wagon model, the top tether

anchor (A) is located under a cover on the ceiling (B).
Open the cover to access the anchors. Be sure to
use an anchor located on the same side of the vehicle
as the seating position where the child restraint will
be placed.
1-41
Securing a Child Restraint Designed for
the LATCH System {CAUTION:
{CAUTION: Each top tether anchor and lower anchor in the
vehicle is designed to hold only one child
restraint. Attaching more than one child
If a LATCH-type child restraint is not attached restraint to a single anchor could cause the
to anchors, the restraint will not be able to anchor or attachment to come loose or even
protect the child correctly. In a crash, the child break during a crash. A child or others could
could be seriously injured or killed. Make sure be injured if this happens. To help prevent
that a LATCH-type child restraint is properly injury to people and damage to your vehicle,
installed using the anchors, or use the attach only one child restraint per anchor.
vehicles safety belts to secure the restraint,
following the instructions that came with that
restraint, and also the instructions in this
manual.
1-42
Folding an empty rear seat with the safety belts
secured may cause damage to the safety belt or the
{CAUTION: seat. When removing the child restraint, always
remember to return the safety belts to their normal,
Children can be seriously injured or strangled stowed position before folding the rear seat.
if a shoulder belt is wrapped around their neck 1. Attach and tighten the lower attachments to the
and the safety belt continues to tighten. lower anchors. If the child restraint does not have
Secure any unused safety belts behind the lower attachments or the desired seating position
child restraint so children cannot reach them. does not have lower anchors, secure the child
restraint with the top tether and the safety belts.
Pull the shoulder belt all the way out of the
Refer to your child restraint manufacturer
retractor to set the lock, if your vehicle has instructions and the instructions in this manual.
one, after the child restraint has been installed.
1.1. Find the lower anchors for the desired
Be sure to follow the instructions of the child
seating position.
restraint manufacturer.
1.2. Put the child restraint on the seat.
1.3. Attach and tighten the lower attachments on
Notice: Contact between the child restraint LATCH the child restraint to the lower anchors.
attachment parts and the vehicles safety belt
assembly may cause damage to these parts. Make
sure when securing unused safety belts behind
the child restraint that there is no contact between
the child restraint LATCH attachment parts and
the vehicles safety belt assembly.
1-43
2. If the child restraint manufacturer recommends that 2.5. Route and tighten the top tether according to
the top tether be attached, attach and tighten the your child restraint instructions and the
top tether to the top tether anchor, if equipped. following instructions:
Refer to the child restraint instructions and
If the position you are
the following steps:
using does not have a
2.1. Find the top tether anchor. headrest or head restraint
2.2. For hatchback models, remove the cargo and you are using a
shade before installing the top tether. single tether, route the
The cargo shade should remain off while tether over the seatback.
the top tether anchor is in use.
2.3. Squeeze and pull the front part of the cover,
if there is one, to access the anchors.
For the center position in a wagon model,
flip the cover on the ceiling to access
the anchor.
If the position you are
2.4. Raise the headrest or head restraint if the
using does not have a
desired seating position has an adjustable
headrest or head restraint
headrest or head restraint. See Head
and you are using a
Restraints on page 1-7.
dual tether, route the tether
over the seatback.
1-44
If the position you are Securing a Child Restraint in a
using has a headrest or
head restraint and you Rear Seat Position
are using a single tether,
When securing a child restraint in a rear seating
route the tether under the
position, study the instructions that came with your child
headrest or head restraint
restraint to make sure it is compatible with this vehicle.
and in between the
headrest or head restraint. If your child restraint has the LATCH system, see
Lower Anchors and Tethers for Children (LATCH) on
page 1-37 for how to install your child restraint
using LATCH. If you secure a child restraint using a
safety belt and it uses a top tether, see Lower Anchors
If the position you are and Tethers for Children (LATCH) on page 1-37 for
using has a headrest or top tether anchor locations.
head restraint and you are Do not secure a child restraint in a position without a
using dual tether, route top tether anchor if a national or local law requires that
the tether under the the top tether be anchored, or if the instructions that
headrest or head restraint come with the child restraint say that the top strap must
and in between the be anchored.
headrest or head
restraint posts. In Canada, the law requires that forward-facing child
restraints have a top tether, and that the tether be
attached.
If your child restraint does not have the LATCH system,
3. Push and pull the child restraint in different you will be using the safety belt to secure the child
directions to be sure it is secure. restraint in this position. Be sure to follow the
instructions that came with the child restraint.
Secure the child in the child restraint when and as
the instructions say.
1-45
If you need to install more than one child restraint in the Make sure the release button is positioned so you
rear seat, be sure to read Where to Put the Restraint would be able to unbuckle the safety belt quickly
on page 1-36. if necessary.
1. Put the child restraint on the seat.
2. Pick up the latch plate, and run the lap and shoulder
portions of the vehicles safety belt through or
around the restraint. The child restraint instructions
will show you how.
4. Pull the rest of the shoulder belt all the way out of
the retractor to set the lock.
3. Push the latch plate into the buckle until it clicks.

If you find that the latch plate will not go fully into
the buckle, see if you are using the correct buckle.
1-46
6. If your child restraint has a top tether, follow the
child restraint manufacturers instructions regarding
the use of the top tether. See Lower Anchors
and Tethers for Children (LATCH) on page 1-37.
7. Push and pull the child restraint in different
directions to be sure it is secure.
To remove the child restraint, unbuckle the vehicles
safety belt and let it go back all the way. If the top tether
is attached to a top tether anchor, disconnect it.
5. To tighten the belt, push down on the child restraint,

pull the shoulder portion of the belt to tighten the
lap portion of the belt and feed the shoulder
belt back into the retractor. If you are using a
forward-facing child restraint, you may find it
helpful to use your knee to push down on the
child restraint as you tighten the belt.
1-47
Securing a Child Restraint in the
Right Front Seat Position {CAUTION:
Your vehicle has airbags. A rear seat is a safer place to
secure a forward-facing child restraint. See Where to A child in a rear-facing child restraint can be
Put the Restraint on page 1-36. seriously injured or killed if the right front
passengers airbag inflates. This is because
In addition, your vehicle has a passenger sensing
the back of the rear-facing child restraint
system which is designed to turn off the right front
passengers frontal airbag and seat-mounted side would be very close to the inflating airbag.
impact airbag (if equipped) under certain conditions. Even though the passenger sensing system is
See Passenger Sensing System on page 1-59 and designed to turn off the right front passengers
Passenger Airbag Status Indicator on page 3-28 frontal airbag if the system detects a rear-facing
for more information on this, including important child restraint, no system is fail-safe, and no
safety information.
one can guarantee that an airbag will not deploy
A label on your sun visor says, Never put a rear-facing under some unusual circumstance, even
child seat in the front. This is because the risk to the though it is turned off. We recommend that
rear-facing child is so great, if the airbag deploys. rear-facing child restraints be secured in a rear
seat, even if the airbag is off.
See Passenger Sensing System on page 1-59
1-48
If your child restraint has the LATCH system, see 2. Put the child restraint on the seat.
Lower Anchors and Tethers for Children (LATCH) on 3. Pick up the latch plate, and run the lap and shoulder
page 1-37 for how to install your child restraint portions of the vehicles safety belt through or
using LATCH. If you secure a child restraint using a around the restraint. The child restraint instructions
safety belt and it uses a top tether, see Lower Anchors will show you how.
and Tethers for Children (LATCH) on page 1-37 for
top tether anchor locations.
Do not secure a child seat in a position without a top
tether anchor if a national or local law requires that the
top tether be anchored, or if the instructions that
come with the child restraint say that the top strap must
be anchored.
In Canada, the law requires that forward-facing child
restraints have a top tether, and that the tether be
attached.
You will be using the lap-shoulder belt to secure the
child restraint in this position. Follow the instructions that
came with the child restraint.
1. Move the seat as far back as it will go before
securing the forward-facing child restraint.
4. Push the latch plate into the buckle until it clicks.
When the passenger sensing system has turned off
the right front passengers frontal airbag and Make sure the release button is positioned so you
seat-mounted side impact airbag (if equipped), would be able to unbuckle the safety belt quickly
the off symbol on the passenger airbag status if necessary.
indicator should light and stay lit when you start the
vehicle. See Passenger Airbag Status Indicator
on page 3-28.
1-49
5. Pull the rest of the shoulder belt all the way out of 6. To tighten the belt, push down on the child restraint,
the retractor to set the lock. pull the shoulder portion of the belt to tighten the
lap portion of the belt and feed the shoulder
belt back into the retractor. If you are using a
forward-facing child restraint, you may find it helpful
to use your knee to push down on the child
restraint as you tighten the belt.
7. Push and pull the child restraint in different
directions to be sure it is secure.
If the airbag or airbags are off, the off symbol will be lit
when the vehicle is started.
1-50
If a child restraint has been installed and the off symbol
is not lit, turn the vehicle off. Remove the child
Airbag System
restraint from the vehicle and reinstall the child restraint. Your vehicle has the following airbags:
If, after reinstalling the child restraint and restarting A frontal airbag for the driver.
the vehicle, the off symbol is still not lit, check to make
sure that the vehicles seatback is not pressing the A frontal airbag for the right front passenger.
child restraint into the seat cushion. If this happens, Your vehicle may have the following airbags:
slightly recline the vehicles seatback and adjust the seat
cushion if possible. Also make sure the child restraint A seat-mounted side impact airbag for the driver.
is not trapped under the vehicle head restraint. A seat-mounted side impact airbag for the right front
If this happens, adjust the head restraint. passenger.
Remove any additional material from the seat such as All of the airbags in your vehicle will have the word
blankets, cushions, seat covers, seat heaters or AIRBAG embossed in the trim or on an attached label
seat massagers before reinstalling or securing the child near the deployment opening.
restraint.
For frontal airbags, the word AIRBAG will appear on the
If the off symbol is still not lit, secure the child in the middle part of the steering wheel for the driver and
child restraint in a rear seat position in the vehicle and on the instrument panel for the right front passenger.
check with your dealer/retailer.
With seat-mounted side impact airbags, the word
To remove the child restraint, unbuckle the vehicles AIRBAG will appear on the side of the seatback closest
safety belt and let it go back all the way. to the door.
1-51
Airbags are designed to supplement the protection
provided by safety belts. Even though todays airbags
are also designed to help reduce the risk of injury {CAUTION:
from the force of an inflating bag, all airbags must inflate
very quickly to do their job. Frontal airbags are designed to deploy in
Here are the most important things to know about the moderate to severe frontal and near frontal
airbag system: crashes. They are not designed to inflate in
rollover, rear crashes, or in many side crashes.
Seat-mounted side impact airbags are
{CAUTION: designed to inflate in moderate to severe
crashes where something hits the side of your
You can be severely injured or killed in a crash vehicle. They are not designed to inflate in
if you are not wearing your safety belt even frontal, in rollover, or in rear crashes.
if you have airbags. Wearing your safety belt
Everyone in your vehicle should wear a safety
during a crash helps reduce your chance of
belt properly whether or not there is an
hitting things inside the vehicle or being
airbag for that person.
ejected from it. Airbags are supplemental
restraints to the safety belts. All airbags are
designed to work with safety belts, but do not
replace them.
1-52
{CAUTION: {CAUTION:
Airbags inflate with great force, faster than the Airbags plus lap-shoulder belts offer the best
blink of an eye. Anyone who is up against, or protection for adults, but not for young
very close to, any airbag when it inflates can children and infants. Neither the vehicles
be seriously injured or killed. Do not sit safety belt system nor its airbag system is
unnecessarily close to the airbag, as you designed for them. Young children and infants
would be if you were sitting on the edge of need the protection that a child restraint
your seat or leaning forward. Safety belts help system can provide. Always secure children
keep you in position before and during a properly in your vehicle. To read how, see
crash. Always wear your safety belt, even with Older Children on page 1-27 or Infants and
airbags. The driver should sit as far back as Young Children on page 1-30.
possible while still maintaining control of the
vehicle.
There is an airbag
Occupants should not lean on or sleep against readiness light on the
the door or side windows in seating positions instrument panel, which
with seat-mounted airbags. shows the airbag symbol.
The system checks the airbag electrical system for

malfunctions. The light tells you if there is an electrical
problem. See Airbag Readiness Light on page 3-27
for more information.
1-53
Where Are the Airbags?
The right front passengers airbag is in the instrument

panel on the passengers side.
The drivers airbag is in the middle of the steering wheel.
1-54
{CAUTION:
If something is between an occupant and an
airbag, the airbag might not inflate properly or it
might force the object into that person causing
severe injury or even death. The path of an
inflating airbag must be kept clear. Do not put
anything between an occupant and an airbag,
and do not attach or put anything on the
steering wheel hub or on or near any other
airbag covering.
Driver Side shown, Passenger Side similar Do not use seat accessories that block the
inflation path of a seat-mounted side impact
If your vehicle has seat-mounted side impact airbags airbag.
for the driver and right front passenger, they are in
the side of the seatbacks closest to the door.
1-55
When Should an Airbag Inflate? If the vehicle hits a narrow object (like a pole), the
airbags could inflate at a different crash speed
Frontal airbags are designed to inflate in moderate to than if the vehicle hits a wide object (like a wall).
severe frontal or near-frontal crashes to help reduce the
potential for severe injuries mainly to the drivers or If the vehicle goes into an object at an angle, the
right front passengers head and chest. However, they airbags could inflate at a different crash speed
are only designed to inflate if the impact exceeds a than if the vehicle goes straight into the object.
predetermined deployment threshold. Deployment Thresholds can also vary with specific vehicle design.
thresholds are used to predict how severe a crash is
In addition, your vehicle has dual-stage frontal airbags.
likely to be in time for the airbags to inflate and
Dual-stage airbags adjust the restraint according to
help restrain the occupants.
crash severity. Your vehicle has electronic frontal
Whether your frontal airbags will or should deploy is not sensors, which help the sensing system distinguish
based on how fast your vehicle is traveling. It depends between a moderate frontal impact and a more severe
largely on what you hit, the direction of the impact, frontal impact. For moderate frontal impacts, dual-stage
and how quickly your vehicle slows down. airbags inflate at a level less than full deployment.
Frontal airbags may inflate at different crash speeds. For more severe frontal impacts, full deployment occurs.
For example: Frontal airbags are not intended to inflate during
If the vehicle hits a stationary object, the airbags vehicle rollovers, rear impacts, or in many side impacts.
could inflate at a different crash speed than if the Your vehicle may or may not have seat-mounted side
vehicle hits a moving object. impact airbags. See Airbag System on page 1-51.
If the vehicle hits an object that deforms, the Seat-mounted side impact airbags are intended to inflate
in moderate to severe side crashes. Seat-mounted side
airbags could inflate at a different crash speed than
impact airbags will inflate if the crash severity is above
if the vehicle hits an object that does not deform.
the systems designed threshold level. The threshold
level can vary with specific vehicle design.
1-56
Seat-mounted side impact airbags are not intended to How Does an Airbag Restrain?
inflate in frontal impacts, near-frontal impacts, rollovers,
or rear impacts. A seat-mounted side impact airbag In moderate to severe frontal or near frontal collisions,
is intended to deploy on the side of the vehicle that is even belted occupants can contact the steering wheel
struck. or the instrument panel. In moderate to severe side
In any particular crash, no one can say whether an collisions, even belted occupants can contact the inside
airbag should have inflated simply because of the of the vehicle.
damage to a vehicle or because of what the repair costs Airbags supplement the protection provided by safety
were. For frontal airbags, inflation is determined by belts. Frontal airbags distribute the force of the
what the vehicle hits, the angle of the impact, and how impact more evenly over the occupants upper body,
quickly the vehicle slows down. For seat-mounted stopping the occupant more gradually. Seat-mounted
side impact airbags, deployment is determined by the side impact airbags distribute the force of the impact
location and severity of the side impact. more evenly over the occupants upper body.
But airbags would not help in many types of collisions,
What Makes an Airbag Inflate? primarily because the occupants motion is not
toward those airbags. See When Should an Airbag
In a deployment event, the sensing system sends an Inflate? on page 1-56 for more information.
electrical signal triggering a release of gas from the
inflator. Gas from the inflator fills the airbag causing the Airbags should never be regarded as anything more
bag to break out of the cover and deploy. The inflator, than a supplement to safety belts.
the airbag, and related hardware are all part of the
airbag module.
Frontal airbag modules are located inside the steering
wheel and instrument panel. For vehicles with
seat-mounted side impact airbags, there are airbag
modules in the side of the front seatbacks closest to
the door.
1-57
What Will You See After an
Airbag Inflates? {CAUTION:
After the frontal and seat-mounted side impact airbags
inflate, they quickly deflate, so quickly that some When an airbag inflates, there may be dust in
people may not even realize the airbags inflated. the air. This dust could cause breathing
Some components of the airbag module may be hot for problems for people with a history of asthma or
several minutes. For location of the airbag modules, other breathing trouble. To avoid this, everyone
see What Makes an Airbag Inflate? on page 1-57. in the vehicle should get out as soon as it is
The parts of the airbag that come into contact with you safe to do so. If you have breathing problems
may be warm, but not too hot to touch. There may but cannot get out of the vehicle after an airbag
be some smoke and dust coming from the vents in the inflates, then get fresh air by opening a window
deflated airbags. Airbag inflation does not prevent or a door. If you experience breathing problems
the driver from seeing out of the windshield or being following an airbag deployment, you should
able to steer the vehicle, nor does it prevent people seek medical attention.
from leaving the vehicle.
Your vehicle has a feature that may automatically

unlock the doors, turn the interior lamps on, and turn on
the hazard warning flashers when the airbags inflate.
You can lock the doors, turn the interior lamps off, and
turn the hazard warning flashers off by using the
controls for those features.
1-58
In many crashes severe enough to inflate the airbag, Passenger Sensing System
windshields are broken by vehicle deformation.
Additional windshield breakage may also occur from Your vehicle has a passenger sensing system for the
the right front passenger airbag. right front passengers position. The passenger
Airbags are designed to inflate only once. After an airbag status indicator will be visible when you start
airbag inflates, you will need some new parts for the vehicle.
the airbag system. If you do not get them, the airbag
The airbag off symbol will
system will not be there to help protect you in
be visible near the clock,
another crash. A new system will include airbag
located in the center of the
modules and possibly other parts. The service
instrument panel, during
manual for your vehicle covers the need to replace
the system check.
other parts.
Your vehicle has a crash sensing and diagnostic
module which records information after a crash.
See Vehicle Data Recording and Privacy on
page 7-16 and Event Data Recorders on page 7-16. When the system check is complete, the airbag off
symbol will be visible under certain conditions.
Let only qualified technicians work on the airbag See Passenger Airbag Status Indicator on page 3-28.
system. Improper service can mean that the The passenger sensing system will turn off the right front
airbag system will not work properly. See your passengers frontal airbag and seat-mounted side
dealer/retailer for service. impact airbag (if equipped) under certain conditions.
The drivers airbags are not part of the passenger
sensing system.
1-59
The passenger sensing system works with a sensor that
is part of the right front passengers seat. The sensor
is designed to detect the presence of a properly-seated {CAUTION:
occupant and determine if the right front passengers
frontal airbag and seat-mounted side impact airbag A child in a rear-facing child restraint can be
(if equipped) should be enabled (may inflate) or not. seriously injured or killed if the right front
Accident statistics show that children are safer if they passengers airbag inflates. This is because
are restrained in the rear rather than the front seat. the back of the rear-facing child restraint
We recommend that children be secured in a rear seat, would be very close to the inflating airbag.
including: an infant or a child riding in a rear-facing Even though the passenger sensing system is
child restraint; a child riding in a forward-facing child designed to turn off the passengers frontal
seat; an older child riding in a booster seat; and children,
airbag and side impact airbag (if equipped) if
who are large enough, using safety belts.
the system detects a rear-facing child restraint,
A label on your sun visor says, Never put a rear-facing no system is fail-safe, and no one can
child seat in the front. This is because the risk to the guarantee that an airbag will not deploy under
rear-facing child is so great, if the airbag deploys. some unusual circumstance, even though it is
turned off. We recommend that rear-facing
child restraints be secured in a rear seat,
even if the airbag or airbags are off.
1-60
The passenger sensing system is designed to turn off If a child restraint has been installed and the off symbol is
the right front passengers frontal airbag and not lit, turn the vehicle off. Remove the child restraint from
seat-mounted side impact airbag (if equipped) if: the vehicle and reinstall the child restraint following the
The right front passenger seat is unoccupied. child restraint manufacturers directions and refer to
Securing a Child Restraint in the Right Front Seat
The system determines that an infant is present in Position on page 1-48.
a rear-facing infant seat. If, after reinstalling the child restraint and restarting the
The system determines that a small child is present vehicle, the off symbol is still not lit, check to make
in a child restraint. sure that the vehicles seatback is not pressing the child
restraint into the seat cushion. If this happens, slightly
The system determines that a small child is present recline the vehicles seatback and adjust the seat
in a booster seat. cushion if possible.
A right front passenger takes his/her weight off of Remove any additional material from the seat such as
the seat for a period of time. blankets, cushions, seat covers, seat heaters, or
The right front passenger seat is occupied by a seat massagers before reinstalling or securing the child
smaller person, such as a child who has outgrown restraint.
child restraints. If the off symbol is still not lit, secure the child in the
Or, if there is a critical problem with the airbag child restraint in a rear seat position in the vehicle and
system or the passenger sensing system. check with your dealer/retailer.
When the passenger sensing system has turned off the The passenger sensing system is designed to enable
right front passengers frontal airbag and seat-mounted (may inflate) the right front passengers frontal airbag
side impact airbag (if equipped), the off symbol will and seat-mounted side impact airbag (if equipped)
light and stay lit to remind you that the airbag or airbags anytime the system senses that a person of adult size
are off. See Passenger Airbag Status Indicator on is sitting properly in the right front passengers seat.
page 3-28. When the passenger sensing system has allowed
the airbag or airbags to be enabled, the off symbol
will not light.
1-61
For some children who have outgrown child restraints
and for very small adults, the passenger sensing system
may or may not turn off the right front passengers
frontal airbag and seat-mounted side impact airbag
(if equipped), depending upon the persons seating
posture and body build. Everyone in your vehicle who
has outgrown child restraints should wear a safety
belt properly whether or not there is an airbag for
that person.
If a person of adult-size is sitting in the right front
passengers seat, but the off indicator is lit, it could be
because that person is not sitting properly in the seat.
If this happens, turn the vehicle off, remove any
additional material from the seat, such as blankets,
cushions, seat covers, seat heaters or seat massagers
and ask the person to place the seatback in the fully
upright position, then sit upright in the seat, centered on
the seat cushion, with the persons legs comfortably
extended. Restart the vehicle and have the person Safety belts help keep the passenger in position on the
remain in this position for two to three minutes. seat during vehicle maneuvers and braking, which
This will allow the system to detect that person and helps the passenger sensing system maintain the
then enable the right front passengers frontal airbag passenger airbag status. See Safety Belts and
and seat-mounted side impact airbag (if equipped). Child Restraints in the Index for additional information
about the importance of proper restraint use.
1-62
We recommend that you not use seat covers or other
aftermarket equipment other than any that GM has
{CAUTION: approved for your specific vehicle. See Adding
Equipment to Your Airbag-Equipped Vehicle on
If the airbag readiness light in the instrument page 1-64 for more information about modifications
panel cluster ever comes on and stays on, that can affect how the system operates.
it means that something may be wrong with
the airbag system. If this ever happens, have
the vehicle serviced promptly, because an {CAUTION:
adult-size person sitting in the right front
passengers seat may not have the protection Stowing of articles under the passengers seat
of the airbag(s). See Airbag Readiness Light or between the passengers seat cushion and
on page 3-27 for more on this, including seatback may interfere with the proper
important safety information. operation of the passenger sensing system.
A thick layer of additional material, such as a blanket

or cushion, or aftermarket equipment such as seat
covers, seat heaters, and seat massagers can affect
how well the passenger sensing system operates.
1-63
Servicing Your Airbag-Equipped Adding Equipment to Your
Vehicle Airbag-Equipped Vehicle
Airbags affect how your vehicle should be serviced.
There are parts of the airbag system in several places
Q: Is there anything I might add to or change
about the vehicle that could keep the airbags
around your vehicle. Your dealer/retailer and the service from working properly?
manual have information about servicing your vehicle
and the airbag system. To purchase a service manual, A: Yes. If you add things that change your vehicles
see Service Publications Ordering Information on frame, bumper system, height, front end or side
page 7-15. sheet metal, they may keep the airbag system from
working properly. Changing or moving any parts of
the front seats, safety belts, the airbag sensing and
{CAUTION: diagnostic module, steering wheel, instrument panel,
front sensors, or airbag wiring can affect the
operation of the airbag system.
For up to 10 seconds after the ignition is
turned off and the battery is disconnected, an In addition, your vehicle has a passenger sensing
airbag can still inflate during improper service. system for the right front passengers position, which
You can be injured if you are close to an includes sensors that are part of the passengers
airbag when it inflates. Avoid yellow seat. The passenger sensing system may not
connectors. They are probably part of the operate properly if the original seat trim is replaced
with non-GM covers, upholstery or trim, or with GM
airbag system. Be sure to follow proper
service procedures, and make sure the person
performing work for you is qualified to do so.
1-64
covers, upholstery or trim designed for a different Q: Because I have a disability, I have to get my
vehicle. Any object, such as an aftermarket seat vehicle modified. How can I find out whether
heater or a comfort enhancing pad or device, this will affect my airbag system?
installed under or on top of the seat fabric, could also
interfere with the operation of the passenger sensing A: If you have questions, call Customer Assistance.
system. This could either prevent proper deployment The phone numbers and addresses for Customer
of the passenger airbag(s) or prevent the passenger Assistance are in Step Two of the Customer
sensing system from properly turning off the Satisfaction Procedure in this manual. See
passenger airbag(s). See Passenger Sensing Customer Satisfaction Procedure on page 7-2.
System on page 1-59. In addition, your dealer/retailer and the service manual
If you have any questions about this, you should have information about the location of the airbag sensors,
contact Customer Assistance before you modify sensing and diagnostic module and airbag wiring.
your vehicle. The phone numbers and addresses
for Customer Assistance are in Step Two of the
Customer Satisfaction Procedure in this manual.
See Customer Satisfaction Procedure on page 7-2.
1-65
Restraint System Check Airbags
The airbag system does not need regularly scheduled
Checking the Restraint Systems maintenance or replacement. Make sure the airbag
readiness light is working. See Airbag Readiness Light
on page 3-27 for more information.
Safety Belts
Notice: If an airbag covering is damaged, opened,
Now and then, make sure the safety belt reminder light
or broken, the airbag may not work properly.
and all your belts, buckles, latch plates, retractors
Do not open or break the airbag coverings. If there
and anchorages are working properly.
are any opened or broken airbag covers, have
Look for any other loose or damaged safety belt system the airbag covering and/or airbag module replaced.
parts. If you see anything that might keep a safety For the location of the airbag modules, see What
belt system from doing its job, have it repaired. Torn or Makes an Airbag Inflate? on page 1-57. See your
frayed safety belts may not protect you in a crash. dealer/retailer for service.
They can rip apart under impact forces. If a belt is torn
or frayed, get a new one right away.
Make sure the safety belt reminder light is working.
See Safety Belt Reminders on page 3-27 for more
information.
Keep safety belts clean and dry. See Care of Safety
Belts on page 5-81.
1-66
Replacing Restraint System Parts If you have had a crash, do you need new belts or
LATCH system (if equipped) parts?
After a Crash After a very minor crash, nothing may be necessary.
But the belt assemblies that were used during any crash
may have been stressed or damaged. See your
{CAUTION: dealer/retailer to have your safety belt assemblies
inspected or replaced.
A crash can damage the restraint systems in If your vehicle has the LATCH system and it was being
your vehicle. A damaged restraint system used during a crash, you may need new LATCH
may not properly protect the person using it, system parts.
resulting in serious injury or even death in a New parts and repairs may be necessary even if the
crash. To help make sure your restraint belt or LATCH system (if equipped), was not being used
systems are working properly after a crash, at the time of the crash.
have them inspected and any necessary If an airbag inflates, you will need to replace airbag
replacements made as soon as possible. system parts. See the part on the airbag system earlier
in this section.
Have your safety belt pretensioners checked if your
vehicle has been in a crash, if your airbag readiness
light stays on after you start your vehicle, or while you
are driving. See Airbag Readiness Light on page 3-27.
1-67
NOTES
1-68
Section 2 Features and Controls
Keys ...............................................................2-2 Manual Transmission Operation ......................2-26
Remote Keyless Entry (RKE) System ................2-3 Parking Brake ..............................................2-28
Remote Keyless Entry (RKE) System Shifting Into PARK (P) (Automatic
Operation ...................................................2-4 Transmission) ...........................................2-29
Doors and Locks .............................................2-6 Shifting Out of PARK (P) ...............................2-30
Door Locks ....................................................2-6 Parking Your Vehicle (Manual Transmission) .....2-31
Central Door Unlocking System ........................2-7 Parking Over Things That Burn .......................2-32
Power Door Locks ..........................................2-7 Engine Exhaust ............................................2-32
Door Ajar Reminder ........................................2-8 Running the Vehicle While Parked ..................2-33
Rear Door Security Locks ................................2-8 Mirrors ...........................................................2-34
Lockout Protection ..........................................2-9 Manual Rearview Mirror .................................2-34
Liftgate ........................................................2-10 Outside Manual Mirrors ..................................2-34
Windows ........................................................2-11 Outside Power Mirrors ...................................2-35
Manual Windows ..........................................2-11 Outside Convex Mirror ...................................2-35
Power Windows ............................................2-12 Outside Heated Mirrors ..................................2-35
Sun Visors ...................................................2-13 Storage Areas ................................................2-36
Theft-Deterrent Systems ..................................2-14 Glove Box ...................................................2-36
Theft-Deterrent System ..................................2-14 Cupholder(s) ................................................2-36
Immobilizer ..................................................2-16 Sunglasses Storage Compartment ...................2-36
Immobilizer Operation ....................................2-16 Front Armrest Storage Area ...........................2-36
Luggage Carrier ...........................................2-37
Starting and Operating Your Vehicle ................2-17 Rear Seat Armrest ........................................2-37
New Vehicle Break-In ....................................2-17 Convenience Net ..........................................2-37
Ignition Positions ..........................................2-18 Cargo Cover ................................................2-38
Starting the Engine .......................................2-19 Hideaway Rear Storage Bins (Wagon Only) ......2-38
Engine Coolant Heater ..................................2-21
Automatic Transmission Operation ...................2-22 Sunroof .........................................................2-39
2-1
Keys
{CAUTION:
Leaving children in a vehicle with the ignition
key is dangerous for many reasons, children or
others could be badly injured or even killed.
They could operate the power windows or
other controls or even make the vehicle move.
The windows will function with the keys in the
ignition and they could be seriously injured or
killed if caught in the path of a closing window.
Do not leave the keys in a vehicle with children.
One key is used for the ignition and all locks.

When a new vehicle is delivered, the dealer/retailer
removes the key tag and gives it to the first owner.
The tag has a code on it that tells your dealer/retailer
how to make extra keys. For vehicle security, keep
the key tag in a safe place and also record the key
number somewhere other than inside of the vehicle.
If you lose your key, you will be able to have a new one
made easily using the tag.
2-2
If you need a new key, contact your dealer/retailer who Changes or modifications to this system by other than
can obtain the correct key code. See Roadside an authorized service facility could void authorization to
Assistance Program on page 7-6 for more information. use this equipment.
Notice: If you ever lock your keys in your vehicle, At times you may notice a decrease in range. This is
you may have to damage the vehicle to get in. normal for any RKE system. If the transmitter does not
Be sure you have spare keys. work or if you have to stand closer to your vehicle
for the transmitter to work, try this:
Remote Keyless Entry (RKE) Check the distance. You may be too far from your
vehicle. You may need to stand closer during rainy or
System snowy weather.
If the vehicle has the Remote Keyless Entry (RKE) Check the location. Other vehicles or objects may be
system, it operates on a radio frequency subject blocking the signal. Take a few steps to the left or
to Federal Communications Commission (FCC) Rules right, hold the transmitter higher, and try again.
and with Industry Canada.
Check to determine if battery replacement is
This device complies with Part 15 of the FCC Rules. necessary. See Battery Replacement later in this
Operation is subject to the following two conditions: section.
1. This device may not cause interference.
If you are still having trouble, see your dealer/retailer
2. This device must accept any interference received, or a qualified technician for service.
including interference that may cause undesired
operation of the device.
This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
2. This device must accept any interference received,
including interference that may cause undesired
operation of the device.
2-3
Remote Keyless Entry (RKE) system will deactivate and the security light will turn off.
The security light is located on the base of the drivers
System Operation door lock.
The LED light (A), on the transmitter, will flash when the If a door is not opened, all of the doors will automatically
buttons on the Remote Keyless Entry (RKE) transmitter lock and the theft-deterrent system will reactivate.
are pressed. You can lock and unlock the vehicles
doors from about 20 feet (6 m) away. Q (Lock): Press Qto lock all of the doors and the
liftgate, if equipped. If all of the doors and the liftgate are
There are other conditions which can affect the closed, the hazard lamps will flash once and the horn
performance of the transmitter. See Remote Keyless will sound to indicate that locking has occurred.
Entry (RKE) System on page 2-3. The theft-deterrent system will activate and the security
light will flash.
If the drivers door is open while pressing lock, all of the
doors, except for the drivers door will lock. If any door
other than the drivers door is open while pressing lock,
all of the doors, including the drivers door, will lock.
S (Panic): If your vehicle has this feature, press S to
turn on the hazard warning flashers. The hazard warning
lamps will flash for about 28 seconds. Press S again to
turn off the hazard warning lamps.
The lock, unlock, and panic buttons, on the RKE
W (Unlock): Press Wto unlock all of the doors and transmitter, will not operate while the key is in the
ignition. The theft-deterrent system will not activate while
the liftgate, if equipped. If all of the doors and the
the key is in the ignition.
liftgate are closed, the hazard lamps will flash twice to
indicate that unlocking has occurred. The theft-deterrent
2-4
Matching Transmitter(s) to Your Vehicle
Each RKE transmitter is coded to prevent another
transmitter from unlocking your vehicle. If a transmitter
is lost or stolen, a replacement can be purchased
through your dealer/retailer. All transmitters need to
be re-coded to match the new transmitter. The lost
transmitter will no longer work after the new transmitters
are re-coded. Each vehicle can have a maximum of
four transmitters matched to it.
Battery Replacement
The battery is weak if the LED light fails to illuminate or
if the transmitter will not work at the normal operating
range. If you have to get close to your vehicle before the
transmitter works, change the battery. To replace the battery in the RKE transmitter, do the
following:
Notice: When replacing the battery, use care not to
1. Remove the screw from the back of the cover and
touch any of the circuitry. Static from your body
open the cover of the transmitter.
transferred to these surfaces may damage the
transmitter. 2. Pull the transmitter unit out of the cover and open
the cover of the transmitter unit.
3. Remove the battery and replace it with the new one.
Make sure the positive side of the battery faces up.
Use one three-volt, CR1616, or equivalent type
battery.
4. Close the cover of the transmitter unit and put the
unit in the cover of the transmitter.
2-5
5. Assemble the transmitter cover and replace the
screw. Make sure the cover is on tightly, so CAUTION: (Continued)
water will not get in.
6. Test the transmitter operation. Young children who get into unlocked
vehicles may be unable to get out. A child
can be overcome by extreme heat and can
Doors and Locks suffer permanent injuries or even death
from heat stroke. Always lock your vehicle
Door Locks whenever you leave it.
Outsiders can easily enter through an
unlocked door when you slow down or
{CAUTION: stop your vehicle. Locking your doors can
help prevent this from happening.
Unlocked doors can be dangerous.
Passengers, especially children, can easily There are several ways to lock and unlock your vehicle.
open the doors and fall out of a moving
vehicle. When a door is locked, the handle From the outside, use your key or the optional Remote
will not open it. You increase the chance Keyless Entry transmitter. See Remote Keyless
of being thrown out of the vehicle in a Entry (RKE) System Operation on page 2-4.
crash if the doors are not locked. So, wear To manually lock and unlock the doors from the outside,
safety belts properly and lock the doors insert the key into the lock and turn it toward the front
whenever you drive. or rear of the vehicle.
2-6
All doors, except for the Central Door Unlocking System
drivers door, can be
locked from the outside Your vehicle may have a central door unlocking system
by pushing down the that is activated from the drivers door.
manual door lock and
From the outside, you can lock or unlock all of the
then closing the door.
doors on your vehicle from the drivers door by using
either the key or the optional Remote Keyless Entry
transmitter. From the inside, you can lock or unlock all
of the doors using the drivers door lock.
Power Door Locks

The drivers door lock cannot be manually locked while On vehicles with power
the door is open. Upon leaving the vehicle, the door locks, the doors can
drivers door can only be locked from the outside by be locked or unlocked
using the key or the optional RKE transmitter. using the drivers door
If your vehicle has a drivers door security light, it is lock switch.
located on the base of the lock. The light turns off when
you unlock the door using the key or the RKE transmitter.
The light turns on when the door is locked using the key
or the RKE transmitter.
Press the switch to lock and unlock the doors.
From the inside, lock and unlock all of the doors by
pushing or pulling the manual door lock. The doors can
also be locked and unlocked with the optional power
door lock switches located on the drivers door.
2-7
Door Ajar Reminder Rear Door Security Locks
If one of the doors on Your vehicle has rear door
is not closed properly security locks on each
while the ignition is on, rear door that prevent
the door ajar light on passengers from opening
the instrument panel the rear doors from the
cluster comes on and inside.
stays on until the doors
are closed.
See Door Ajar Light on page 3-39 for additional

information. Using the Rear Door Security Lock
1. Move the lever up to lock.
2. Close the door.
3. Do the same thing to the other rear door lock.
Notice: Pulling the inside door handle while the
rear door security locks are engaged could damage
your vehicle. Do not pull the inside door handle
while the rear door security locks are engaged.
The rear doors on your vehicle cannot be opened from
the inside while this feature is in use.
2-8
Opening a Rear Door When the Lockout Protection
Security Lock is On This feature helps prevent locking the key in the car.
1. Unlock the door from the inside. The drivers door can only be locked with the door
closed. From the outside of the vehicle, close the
2. Open the door from the outside. drivers door and lock it using the key or the Remote
If you do not cancel the security lock, adults or older Keyless Entry transmitter.
children who ride in the rear will not be able to open the This feature cannot guarantee that you will never be
rear door from the inside. You should let adults and locked out of your vehicle. Always remember to
older children know how to cancel the locks. take your key with you.
Canceling the Rear Door Security Lock
1. Unlock the door from the inside and open the
door from the outside.
2. Move the lever down to unlock.
3. Do the same for the other rear door.
The rear door locks can now be locked and unlocked
normally.
2-9
Liftgate The liftgate can be locked and unlocked from
outside of the vehicle by inserting the key into the
lock and turning it. The Remote Keyless Entry
transmitter, if the vehicle has one, can also be used.
{CAUTION: Then pull up the handle above the license plate to
open the liftgate.
It can be dangerous to drive with the liftgate
open because carbon monoxide (CO) gas can When closing the liftgate, close it from the center to
make sure it fully latches.
come into your vehicle. You cannot see or
smell CO. It can cause unconsciousness and
even death. If you must drive with the liftgate
open or if electrical wiring or other cable
connections must pass through the seal
between the body and the liftgate:
Make sure all other windows are shut.
Turn the fan on your heating or cooling
system to its highest speed and select the
control setting that will force outside air
into your vehicle. See Climate Control
System on page 3-19.
If you have air outlets on or under the
instrument panel, open them all the way.
See Engine Exhaust on page 2-32.
2-10
Windows
{CAUTION:
Leaving children, helpless adults, or pets in a
vehicle with the windows closed is dangerous.
They can be overcome by the extreme heat
and suffer permanent injuries or even death
from heat stroke. Never leave a child, a
helpless adult, or a pet alone in a vehicle,
especially with the windows closed in warm or
hot weather.
Manual Windows
Use the window crank to open and close each window.
The rear windows do not open fully.
2-11
Power Windows If your vehicle has this
feature, the power window
switches are located on
the drivers door armrest.
{CAUTION:
Leaving children, helpless adults, or pets in a
vehicle with the windows closed is dangerous.
They can be overcome from extreme heat in
warm or hot weather and suffer permanent
injuries or even death from heat stroke.
Uplevel shown,
Leaving children in a vehicle with the ignition
Base similar
key is dangerous for many reasons, children or
others could be badly injured or even killed. In addition, each passenger door has a switch for its
They could operate the power windows or own window. The ignition must be turned to ON/RUN to
other controls or even make the vehicle move. use the power windows. To lower a window, press
The windows will function with the keys in the the switch. To raise a window, lift up on the switch.
ignition and they could be seriously injured or
killed if caught in the path of a closing window.
Do not leave keys in a vehicle with children.
When there are children in the rear seat use the
window lockout button to prevent unintentional
operation of the windows.
2-12
Express-Down Window Sun Visors
The drivers window may also have an express-down To block out glare you can pull the visors down.
feature. This switch is labeled AUTO. Press the They can also be removed from the center mount and
switch then release it and the drivers window goes all moved to the side.
the way down.
To stop the window while it is lowering, press the switch Visor Vanity Mirror
again. To raise the window, pull up and hold the switch.
Your vehicle has vanity mirrors located on the back of
the sun visors. Pull the sun visor down and lift the cover
Window Lockout to expose the vanity mirror.
The drivers power window
controls may also include
a lockout button.
Press the lockout button to stop the front and rear

passengers from using their window switches. The driver
can still operate all the windows with the lock on.
Press the lockout button again to return to normal
window operation.
2-13
Theft-Deterrent Systems 3. Lock the door using the remote keyless entry
transmitter. The transmitter must be used to activate
Vehicle theft is big business, especially in some cities. the theft-deterrent system.
Although your vehicle has a number of theft-deterrent The LED light on the transmitter will flash once.
features, we know that nothing we put on it can make it
impossible to steal. All of the doors will lock.
The hazard warning lamps will flash once and
Theft-Deterrent System the horn will sound.
Your vehicle may have a theft-deterrent system.

The theft-deterrent mode will activate.
The theft-deterrent system will not arm when you lock the The security light will flash once every second to
doors using the key or the manual door lock. It activates indicate that the theft-deterrent system is armed.
only when you use the optional remote keyless entry The security light is located on the base of
transmitter. the drivers door lock.
To avoid activating the alarm by accident, use one of
Arming the System the following methods:
To arm the system: Unlock the drivers or passengers door using
1. Turn the ignition to LOCK/OFF and remove the key the key.
from the ignition. Press the unlock button on the remote keyless
If the key is inserted in the ignition, the transmitter entry transmitter.
will not operate the theft-deterrent system.
Unlocking a door any other way will activate the alarm
2. Close the doors, the windows, the hood, and the when a door or the liftgate is opened.
liftgate.
If you do not want to arm the theft-deterrent system,
Make sure the windows are closed, as the system lock the vehicle using the key or the manual door locks.
can be activated even if the windows are open.
2-14
Disarming the System How to Turn Off the System Alarm
To disarm the system, use one of the following methods: If the system alarm is active, it can be deactivated using
Unlock the drivers or passengers door using one of the following methods:
the key. Press the lock or unlock button on the remote
Press the unlock button on the transmitter. keyless entry transmitter.
The LED light on the transmitter will Unlock the drivers or passengers front door
flash once. using the key.
All of the doors will unlock. Otherwise, the alarm will automatically stop after
30 seconds. The system will then lock the doors and
The hazard warning lamps will flash twice.
reactivate the theft-deterrent system.
The theft-deterrent mode will deactivate.
If the door is not opened or if the engine is not started How to Detect a Tamper Condition
within 30 seconds after disarming the system with
the transmitter, all of the doors will automatically lock If the hazard warning lamps flash once when you press
and the theft-deterrent mode will reactivate. the lock or unlock buttons on the remote keyless entry
transmitter, that means the theft-deterrent system alarm
was triggered while you were away, from the vehicle.
How the System Alarm is Activated
Do not leave the key or device that disarms or
If a door or the liftgate is opened without using the key deactivates the theft deterrent system in the vehicle.
or the remote keyless entry transmitter, the horn will
sound and the lamps will flash for up to 30 seconds.
2-15
Immobilizer Immobilizer Operation
This device complies with Part 15 of the FCC Rules. Your vehicle may have a passive theft-deterrent system.
The immobilizer system prevents your vehicle from
1. This device may not cause interference. being started by unauthorized persons.
2. This device must accept any interference received, The system is automatically armed when the key is
including interference that may cause undesired removed from the ignition.
operation.
You do not have to manually arm or disarm the system.
This device complies with RSS-210 of Industry Canada.
The security light will come on if there is a problem
with arming or disarming the theft-deterrent system.
Your vehicle has a special key that works with the
2. This device must accept any interference received, theft-deterrent system. There is a transponder in the key
including interference that may cause undesired head that is electronically coded. The correct key will
operation of the device. start the vehicle. An invalid key immobilizes the engine.
Changes or modifications to this system by other than The immobilizer system isolates the power supply to
an authorized service facility could void authorization to the ignition system, the fuel pump and the fuel injectors.
use this equipment. If the immobilizer system does not recognize the
electronic code when the key is turned to START, the
engine will not start and the security light will flash.
If your key is ever damaged, you may not be able to
start your vehicle.
2-16
When trying to start the vehicle, if the engine does not
start and the security light continues flashing, there
Starting and Operating
may be a problem with the theft-deterrent system. Your Vehicle
Turn the ignition off and try again.
If the engine still does not start, and the key appears to New Vehicle Break-In
be undamaged, try another key. At this time, you may
also want to check the fuse. See Fuses and Circuit Notice: Your vehicle does not need an elaborate
Breakers on page 5-89. If the engine still does not start break-in. But it will perform better in the long run if
with the other key, your vehicle needs service. If your you follow these guidelines:
vehicle does start, the first key may be faulty.
See your dealer/retailer who can have a new key made. Do not drive at any one constant speed, fast or
slow, for the first 500 miles (805 km). Do not
Up to five keys may be programmed for the vehicle. make full-throttle starts. Avoid downshifting to
If you lose or damage your keys, only a dealer/retailer brake or slow the vehicle.
can have new keys made.
Avoid making hard stops for the first 200 miles
In an emergency, contact Roadside Assistance.
(322 km) or so. During this time the new brake
See Roadside Assistance Program on page 7-6.
linings are not yet broken in. Hard stops
Do not leave the key or device that disarms or with new linings can mean premature wear and
deactivates the theft deterrent system in the vehicle. earlier replacement. Follow this breaking-in
guideline every time you get new brake linings.
Following break-in, engine speed and load can be
gradually increased.
2-17
Ignition Positions Notice: Using a tool to force the key from the
ignition switch could cause damage or break the
The ignition switch can be key. Use the correct key and turn the key only with
turned to four different your hand. Make sure the key is all the way in.
positions with the key. If it is, turn the steering wheel left and right while
you turn the key hard. If none of this works,
then your vehicle needs service.
LOCK/OFF: This position locks the steering wheel,

ignition, shift lever and transmission. This is the only
position in which you can insert or remove the key.
For easier key operation when unlocking the steering
wheel, move the steering wheel from right to left
and turn the key to ACC/ACCESSORY.
ACC (ACC/ACCESSORY): This position operates

{CAUTION: some of the electrical accessories, such as the radio,
but not the climate control system.
On manual transmission vehicles, turning the
key to LOCK/OFF and removing it will lock the
steering column and result in a loss of ability to
steer the vehicle. This could cause a collision.
If you need to turn the engine off while the
vehicle is moving, turn the key only to
ACC/ACCESSORY. Do not push the key in
while the vehicle is moving.
2-18
ON/RUN: This is the position the switch returns after Starting the Engine
you start the engine and release the key. The switch
stays in RUN when the engine is running. But even Automatic Transmission
when the engine is not running, you can use ON/RUN
to operate the electrical accessories, and to display Move the shift lever to PARK (P) or NEUTRAL (N).
some instrument panel warning lights. The engine will not start in any other position that is
a safety feature. To restart when you are already
START: This position starts the engine. When the moving, use NEUTRAL (N) only.
engine starts, release the key. The switch returns to
ON/RUN for normal driving. Do not turn the key to Notice: Do not try to shift to PARK (P) if your
START if the engine is running. vehicle is moving. If you do, you could damage the
transmission. Shift to PARK (P) only when your
Even if the engine is not running, ACC/ACCESSORY vehicle is stopped.
and ON/RUN allow you to operate electrical accessories,
such as the radio.
Manual Transmission
The shift lever should be in NEUTRAL and the parking
brake engaged. Hold the clutch pedal to the floor
and start the engine. Your vehicle will not start if the
clutch pedal is not all the way down that is a safety
feature.
2-19
Starting Procedure 3. If the engine still will not start, or starts but then
stops, it could be flooded with too much gasoline.
1. With your foot off the accelerator pedal, turn the Try pushing your accelerator pedal all the way to the
ignition to START. When the engine starts, let go floor and holding it there as you hold the key in
of the key. The idle speed will go down as your START for about three seconds. If the vehicle starts
engine gets warm. briefly but then stops again, do the same thing,
Notice: Holding your key in START for longer than but this time keep the pedal down for five or
15 seconds at a time will cause your battery to six seconds. This clears the extra gasoline from
be drained much sooner. And the excessive heat the engine.
can damage your starter motor. Wait about Notice: The engine is designed to work with the
15 seconds between each try to help avoid draining electronics in your vehicle. If electrical parts or
your battery or damaging your starter. accessories are added, you could change the way
2. If it does not start, wait about 15 seconds and try the engine operates. Before adding electrical
again to start the engine by turning the ignition to equipment, check with your dealer/retailer. If you
START. Wait about 15 seconds between each try. do not, the engine might not perform properly.
Any resulting damage would not be covered by your
When the engine has run about 10 seconds to
vehicles warranty.
warm up, your vehicle is ready to be driven. Do not
run your engine at high speed when it is cold.
If the weather is below freezing (32F or 0C), let
the engine run for a few minutes to warm up.
2-20
Engine Coolant Heater
The engine coolant heater can help in cold weather {CAUTION:
conditions at or below 0F (18C) for easier starting
and better fuel economy during engine warm-up. Plug in Plugging the cord into an ungrounded outlet
the coolant heater at least four hours before starting could cause an electrical shock. Also, the
your vehicle. wrong kind of extension cord could overheat
and cause a fire. You could be seriously
To Use the Engine Coolant Heater injured. Plug the cord into a properly grounded
1. Turn off the engine. three-prong 110-volt AC outlet. If the cord will
2. Open the hood and unwrap the electrical cord. not reach, use a heavy-duty three-prong
The cord is located on the driver side of the extension cord rated for at least 15 amps.
engine compartment, behind the battery.
3. Plug it into a normal, grounded 110-Volt AC outlet. 4. Before starting the engine, be sure to unplug and
store the cord as it was before to keep it away
from moving engine parts. If you do not, it could be
damaged.
How long should you keep the coolant heater plugged
in? The answer depends on the outside temperature, the
kind of oil you have, and some other things. Instead
of trying to list everything here, we ask that you contact
your dealer/retailer in the area where you will be
parking your vehicle. The dealer/retailer can give you
the best advice for that particular area.
2-21
Automatic Transmission Operation PARK (P): This position locks the front wheels. It is
the best position to use when the start your engine
If your vehicle has an because your vehicle cannot move easily.
automatic transmission,
the shift lever is located
on the console between {CAUTION:
the seats.
It is dangerous to get out of your vehicle if the
shift lever is not fully in PARK (P) with the
parking brake firmly set. Your vehicle can roll.
Do not leave your vehicle when the engine is
running unless you have to. If you have left
the engine running, the vehicle can move
Your vehicle may also have an electronic shift position suddenly. You or others could be injured.
indicator that displays the position of the shift lever. To be sure your vehicle will not move, even
This indicator is located to the right of the trip odometer
when you are on fairly level ground, always set
on the instrument panel cluster.
your parking brake and move the shift lever
Movement between certain positions requires pushing to PARK (P). See Shifting Into PARK (P)
the shift lever to the passenger side while shifting. (Automatic Transmission) on page 2-29.
This prevents you from changing positions unexpectedly
by blocking the straight movement of the shift lever
while the vehicle is moving.
2-22
Make sure the shift lever is fully in PARK (P) before
starting the engine. Your vehicle has an automatic
transmission shift lock control system. The regular {CAUTION:
brakes must be applied before you can shift from
PARK (P) when the ignition key is in ON/RUN. If you Shifting into a drive gear while the engine is
cannot shift out of PARK (P) while holding the brake running at high speed is dangerous. Unless
pedal down, see Shifting Out of PARK (P) on page 2-30.
your foot is firmly on the brake pedal, your
REVERSE (R): Use this gear to back up. vehicle could move very rapidly. You could
lose control and hit people or objects. Do not
When shifting from NEUTRAL (N) to REVERSE (R),
shift into a drive gear while your engine is
you must press down on the shift lever while shifting.
running at high speed.
Notice: Shifting to REVERSE (R) while your vehicle
is moving forward could damage the transmission.
The repairs would not be covered by your warranty. Notice: Shifting out of PARK (P) or NEUTRAL (N)
Shift to REVERSE (R) only after your vehicle is with the engine running at high speed may damage
stopped. the transmission. The repairs would not be
covered by your warranty. Be sure the engine is not
To rock your vehicle back and forth to get out of snow,
running at high speed when shifting your vehicle.
ice, or sand without damaging the transmission, see
If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow on DRIVE (D): This position is for normal driving.
page 4-17.
Notice: If your vehicle seems to start up rather
NEUTRAL (N): In this position, the engine does not slowly or not shift gears when you go faster, and
connect with the wheels. To restart while you are you continue to drive your vehicle that way, you
already moving, use NEUTRAL (N) only. Also, use could damage the transmission. Have your vehicle
NEUTRAL (N) when your vehicle is being towed. serviced right away.
2-23
THIRD (3): This position is also used for normal driving, FIRST (1): This position gives you even more power
however, it offers more power and lower fuel economy but lower fuel economy than SECOND (2). Use it
than DRIVE (D). Here are some times you might choose on very steep hills, or in deep snow or mud. If the shift
THIRD (3) instead of DRIVE (D): lever is put in FIRST (1), the transmission does not
When driving on hilly, winding roads. shift into first gear until the vehicle is going slowly
enough.
When going down a steep hill.
Notice: Spinning the tires or holding the vehicle
SECOND (2): This position gives you more power but in one place on a hill using only the accelerator
lower fuel economy. Use SECOND (2) on hills. It can pedal may damage the transmission. The repair will
help control the vehicles speed as you go down not be covered by your warranty. If you are stuck,
steep mountain roads, but then you would also want to do not spin the tires. When stopping on a hill,
use your brakes off and on. use the brakes to hold the vehicle in place.
Notice: Do not drive in SECOND (2) at speeds If there is a malfunction with the automatic transmission,
over 65 mph (105 km/h), or you can damage the Check Engine Light or the HOLD indicator light
the transmission. Use THIRD (3) or AUTOMATIC will turn on or flash. See Malfunction Indicator Lamp
OVERDRIVE (D) as much as possible. Do not shift on page 3-34 or Hold Mode Light on page 3-33.
into SECOND (2) unless you are going slower Take your vehicle to your dealer/retailer as soon
than 65 mph (105 km/h) or you can damage as possible.
your engine.
2-24
Hold Mode When hold mode is activated, the transmission operates
in the following ways:
If your vehicles transmission has a hold mode, select
this mode to drive with some characteristics of a manual When the transmission is in DRIVE (D), the
transmission. With hold mode turned on, the automatic transmission operates in a gear range of
transmission stays in a specific gear range. SECOND (2) to THIRD (3) to DRIVE (D) and tries
to maintain DRIVE (D) for as long as possible.
Press the HOLD button on When the transmission is in THIRD (3), the
the shift lever console to transmission operates in a gear range of
turn on hold mode. SECOND (2) to THIRD (3) and tries to maintain
THIRD (3) for as long as possible.
When the transmission is in SECOND (2), the
transmission is fixed in that gear.
When the transmission is in FIRST (1), the
transmission is fixed in that gear.
Hold Mode Functions

Winter Function
Select hold mode while in DRIVE (D), THIRD (3) or
Press the button again to turn off hold mode, and return SECOND (2) to help the vehicle maintain traction
to normal automatic transmission operation. on slippery road surfaces, such as snow, mud, or ice.
While on, the HOLD indicator light on the instrument
panel cluster will light up. See Hold Mode Light on Manually Controlling Shift
page 3-33. Select hold mode to use your automatic transmission
like a four-speed manual transmission.
2-25
Manual Transmission Operation Shift into FIRST (1) while you are going less than
20 mph (32 km/h). If you have come to a complete stop
Five-Speed and it is hard to shift into FIRST (1), put the shift
lever in NEUTRAL and let up on the clutch. Press the
clutch pedal back down. Then shift into FIRST (1).
This is the shift pattern for
a Five-Speed transmission. SECOND (2): Press the clutch pedal as you let up on
the accelerator pedal and shift into SECOND (2).
Then, slowly let up on the clutch pedal as you press the
accelerator pedal.
THIRD (3), FOURTH (4) and FIFTH (5): Shift into
THIRD (3), FOURTH (4) and FIFTH (5), the same way
you do for SECOND (2). Slowly let up on the clutch
pedal as you press the accelerator pedal.
To stop, let up on the accelerator pedal and press the
brake pedal. Just before the vehicle stops, press
Here is how to operate a manual transmission: the clutch pedal and the brake pedal, and shift to
NEUTRAL.
FIRST (1): Press the clutch pedal and shift into
FIRST (1). Then, slowly let up on the clutch pedal as
you press the accelerator pedal.
2-26
NEUTRAL: Use this position when you start or idle Shift Speeds
the engine.
REVERSE (R): To back up, press down the clutch
pedal, lift up the ring on the shift lever and shift {CAUTION:
into REVERSE (R). Let up on the clutch pedal slowly
while pressing the accelerator pedal.
If you skip a gear when you downshift, you
Notice: Shifting to REVERSE (R) while your vehicle could lose control of your vehicle. You could
is moving forward could damage the transmission. injure yourself or others. Do not shift down
The repairs would not be covered by your warranty. more than one gear at a time when you
Shift to REVERSE (R) only after your vehicle is downshift.
stopped.
Also, use REVERSE (R), along with the parking brake,
for parking your vehicle.
2-27
Parking Brake To set the parking brake, hold the brake pedal down
and pull up on the parking brake lever. If the ignition is
on, the brake system warning light will come on.
See Brake System Warning Light on page 3-31.
To release the parking brake, hold the brake pedal
down. Pull the parking brake lever up until you can press
the release button. Hold the release button in as you
move the brake lever all the way down.
Notice: Driving with the parking brake on can
overheat the brake system and cause premature
wear or damage to brake system parts. Make sure
that the parking brake is fully released and the brake
warning light is off before driving.
The parking brake lever is located between the

bucket seats.
2-28
Shifting Into PARK (P) Leaving Your Vehicle With the Engine
(Automatic Transmission) Running (Automatic Transmission)
{CAUTION: {CAUTION:
It can be dangerous to get out of your vehicle It can be dangerous to leave your vehicle with
if the shift lever is not fully in PARK (P) with the engine running. Your vehicle could move
the parking brake firmly set. Your vehicle can suddenly if the shift lever is not fully in
roll. If you have left the engine running, the PARK (P) with the parking brake firmly set.
vehicle can move suddenly. You or others And, if you leave the vehicle with the engine
could be injured. To be sure your vehicle will running, it could overheat and even catch fire.
not move, even when you are on fairly level You or others could be injured. Do not leave
ground, use the steps that follow. your vehicle with the engine running.
1. Hold the brake pedal down and set the parking brake. If you have to leave your vehicle with the engine
running, be sure your vehicle is in PARK (P) and your
See Parking Brake on page 2-28 for more information. parking brake is firmly set before you leave it. After you
2. Move the shift lever into PARK (P) by pushing the have moved the shift lever into PARK (P), hold the
lever toward the passenger side of the vehicle and regular brake pedal down. Then, see if you can move
then up. the shift lever away from PARK (P). If you can, it means
that the shift lever was not fully locked into PARK (P).
3. Turn the ignition to LOCK/OFF.
4. Remove the key and take it with you. If you can
leave your vehicle with the ignition key in your
hand, your vehicle is in PARK (P).
2-29
Torque Lock (Automatic Transmission) Shifting Out of PARK (P)
If you are parking on a hill and you do not shift your An automatic transmission vehicle has an automatic
transmission into PARK (P) properly, the weight of the transmission shift lock control system which locks
vehicle may put too much force on the parking pawl the shift lever in PARK (P) when the ignition is in
in the transmission. You may find it difficult to pull the LOCK/OFF. You have to fully apply your regular brakes
shift lever out of PARK (P). This is called torque lock. before you can shift from PARK (P) when the ignition
To prevent torque lock, set the parking brake and is turned to ON. See Automatic Transmission Operation
then shift into PARK (P) properly before you leave the on page 2-22.
drivers seat. To find out how, see Shifting Into PARK (P)
(Automatic Transmission) on page 2-29. If you cannot shift out of PARK (P) while holding the
brake pedal down, try this:
When you are ready to drive, move the shift lever out of
PARK (P) before you release the parking brake. 1. Set the parking brake.
If torque lock does occur, you may need to have another 2. Turn the ignition off and remove the key.
vehicle push yours a little uphill to take some of the 3. Pry off the cover over the shift-lock release slot
pressure from the parking pawl in the transmission, using a small, flat object. The shift-lock release
so you can pull the shift lever out of PARK (P). slot is located at the top of the shift lever.
2-30
4. Insert the key into the Parking Your Vehicle
shift-lock release slot
and press and hold (Manual Transmission)
the key.
Before leaving your vehicle, do the following:
1. Hold the brake pedal down and firmly apply the
parking brake.
2. Fully press in the clutch pedal and place the shift
lever into the gear position as stated below:
When parking on level ground, place the shift
lever into NEUTRAL.
When parking downhill, place the shift lever in
REVERSE (R).
5. Shift to NEUTRAL (N). When parking uphill, place the shift lever in
6. Remove the key from the shift-lock release slot, FIRST (1).
insert the key into the ignition and start the engine. 3. After shifting, turn the ignition to LOCK/OFF,
7. Replace the shift-lock release slot cover. remove the key and release the clutch.
8. Apply and hold the regular brake fully and release
the parking brake.
9. Shift to the gear you want.
10. Have the system fixed as soon as you can.
2-31
Parking Over Things That Burn Engine Exhaust
{CAUTION: {CAUTION:
Things that can burn could touch hot exhaust Engine exhaust can kill. It contains the gas
parts under your vehicle and ignite. Do not carbon monoxide (CO), which you cannot see or
park over papers, leaves, dry grass, or other smell. It can cause unconsciousness and death.
things that can burn. You might have exhaust coming in if:
The exhaust system sounds strange or
different.
Your vehicle gets rusty underneath.
Your vehicle was damaged in a collision.
Your vehicle was damaged when driving
over high points on the road or over road
debris.
Repairs were not done correctly.
Your vehicle or the exhaust system has
been modified improperly.
If you ever suspect exhaust is coming into your
vehicle:
Drive it only with all the windows down to
blow out any CO; and
Have your vehicle fixed immediately.
2-32
Running the Vehicle While Parked
It is better not to park with the engine running. But if you {CAUTION:
ever have to, here are some things to know.
It can be dangerous to get out of your vehicle
if the automatic transmission shift lever is not
{CAUTION: fully in PARK (P) with the parking brake firmly
set. Your vehicle can roll. Do not leave your
Idling the engine with the climate control vehicle when the engine is running unless you
system off could allow dangerous exhaust into have to. If you have left the engine running,
your vehicle. See the earlier caution under the vehicle can move suddenly. You or others
Engine Exhaust on page 2-32. could be injured. To be sure your vehicle will
not move, even when it is on fairly level
Also, idling in a closed-in place can let deadly
ground, always set the parking brake and
carbon monoxide (CO) into your vehicle even if
move the automatic transmission shift lever to
the climate control fan is at the highest setting.
PARK (P), or the manual transmission shift
One place this can happen is a garage.
lever to NEUTRAL.
Exhaust with CO can come in easily.
NEVER park in a garage with the engine
running. Follow the proper steps to be sure your vehicle will not
move. If you have an automatic transmission, see
Another closed-in place can be a blizzard.
Shifting Into PARK (P) (Automatic Transmission) on
See Winter Driving on page 4-13. page 2-29.
2-33
Mirrors
Manual Rearview Mirror
When you are sitting in a comfortable driving position,
adjust the mirror so you can see clearly behind your
vehicle. Hold the mirror in the center to move it up or
down and side to side. The day/night adjustment allows
you to adjust the mirror to avoid glare from the lamps
behind you. Push the tab forward for daytime use
and pull it for nighttime use.
Outside Manual Mirrors

The outside rearview mirrors should be adjusted so you
can see the side of your vehicle when you are sitting Adjust the outside mirrors with the control levers on the
in a comfortable driving position. driver and passenger doors.
The outside rearview mirrors can be folded flat against
the side of the vehicle by pushing them toward the
vehicle.
2-34
Outside Power Mirrors Outside Convex Mirror
{CAUTION:
A convex mirror can make things (like other
vehicles) look farther away than they really are.
If you cut too sharply into the right lane, you
could hit a vehicle on your right. Check your
inside mirror or glance over your shoulder
before changing lanes.
The passenger side mirror is convex. A convex mirrors

surface is curved so more can be seen from the
driver seat. It also makes things, like other vehicles,
Your vehicle may have outside power mirrors. look farther away than they really are.
The control for the power mirrors is located on the
drivers side door trim.
Outside Heated Mirrors
Move the outside power mirror control to L while
adjusting the left mirror and to R while adjusting the If your vehicle has this feature, when you operate the rear
right mirror. Place the control in the center position window defogger, the heated drivers and passengers
when not adjusting either mirror. To adjust a mirror, outside power mirrors are warmed to help clear them of
press the four-way control pad to move the mirror in ice, snow, and condensation. See Rear Window and
the desired direction. The ignition must be turned Outside Mirror Defogger under Climate Control System
to ON/RUN to adjust the mirrors. on page 3-19 for more information.
The outside rearview mirrors can be folded flat against
the side of the vehicle by pushing them toward the
vehicle.
2-35
Storage Areas Sunglasses Storage Compartment
Your vehicle has shopping hooks on each front seatback The sunglasses storage compartment is located
for your convenience. above the drivers door. To open it, pull down and
hold the upper part of the cover. To close the
Glove Box compartment, let go of the cover and the compartment
will automatically close.
To open the glove box, lift up on the lever.
Cupholder(s) Front Armrest Storage Area

The cupholders are located in the center console and Your vehicle has a front armrest storage area.
in the rear seat center armrest. To use the front To open the storage area, pull up on the lift lever
cupholders, move the inner support forward or and raise the lid. To close the storage area, lower the
backward. If your vehicle has rear cupholders, push lid and push it down until it latches securely.
down on the rear seat center armrest to use them.
2-36
Luggage Carrier Notice: Loading cargo on the roof rack that weighs
more than 220 lbs (100 kg) or hangs over the rear
or sides of the vehicle may damage your vehicle.
Load cargo so that it rests on the slats as far
{CAUTION: forward as possible and against the side rails,
making sure to fasten it securely.
If you try to carry something on top of your Do not exceed the maximum vehicle capacity when
vehicle that is longer or wider than the roof loading your vehicle. For more information on vehicle
rack like paneling, plywood, a mattress and capacity and loading, see Loading Your Vehicle on
so forth the wind can catch it as you drive page 4-18.
along. This can cause you to lose control. To prevent damage or loss of cargo as you are driving,
What you are carrying could be violently torn check now and then to make sure cargo is still securely
off, and this could cause you or other drivers fastened.
to have a collision, and of course damage your
vehicle. You may be able to carry something
like this inside. But, never carry something
Rear Seat Armrest
longer or wider than the roof rack on top of Your vehicle may have a rear seat armrest that contains
your vehicle. two cupholders. To access the cupholders, pull the
armrest down from the rear seatback.
The roof rack with side rails lets you to load things on
top of your vehicle. Do not put things on top of your
Convenience Net
vehicle that are wider or longer than the roof rack. The convenience net can help keep small loads from
moving during sharp turns or quick starts and stops.
Hang the four net hooks in the metal rings on each
corner of the floor.
2-37
Cargo Cover Hideaway Rear Storage Bins
(Wagon Only)
Your vehicle may have a cargo cover. Pull the handle of

the cover toward the rear of the vehicle and insert the
retainer into the slot located on both sides of the tailgate There are various bins under the luggage compartment
openings. To remove the cover, release the handle after floor. To access the bins, pull up on the floor mat handle.
pulling it toward you. The cover will retract automatically.
Do not place items on top of the cargo cover.
2-38
Sunroof To fully open the sunroof, push the rear part of the
switch. The sunroof will open automatically until the front
If the vehicle has this feature, the switch is located or the rear part of the switch is pushed again. To close
between the map lamp buttons. The sunroof will only the sunroof, push the front part of the switch and hold
operate when the ignition is turned to ON/RUN. it until the sunroof is closed. The sunroof will stop if the
The sunroof can be opened to a vent position or it can switch is released during operation.
be express-opened all of the way.
In both the vent and fully open positions, the air flow
The sunroof must be manually opened or closed. can be adjusted for driving comfort by pushing and
holding the switch until the sunroof moves to the
desired position.
The sunroof glass panel cannot be opened or closed if
the vehicle has an electrical failure.
To open the sunroof to the vent position, push the front

part of the switch. To return the sunroof to its original
position, push the rear part of the switch and hold it until
the sunroof reaches the desired position.
2-39
NOTES
2-40
Section 3 Instrument Panel
Instrument Panel Overview ...............................3-4 Climate Controls ............................................3-19
Hazard Warning Flashers ................................3-6 Climate Control System .................................3-19
Other Warning Devices ...................................3-6 Outlet Adjustment .........................................3-22
Horn .............................................................3-6 Passenger Compartment Air Filter ...................3-23
Tilt Wheel .....................................................3-6 Warning Lights, Gages, and Indicators ............3-24
Turn Signal/Multifunction Lever .........................3-7 Instrument Panel Cluster ................................3-25
Turn and Lane-Change Signals ........................3-7 Speedometer and Odometer ...........................3-26
Headlamp High/Low-Beam Changer ..................3-8 Trip Odometer ..............................................3-26
Flash-to-Pass .................................................3-8 Tachometer .................................................3-26
Windshield Wipers ..........................................3-8 Safety Belt Reminders ...................................3-27
Windshield Washer .........................................3-9 Airbag Readiness Light ..................................3-27
Rear Window Wiper/Washer ...........................3-10 Passenger Airbag Status Indicator ...................3-28
Cruise Control ..............................................3-10 Charging System Light ..................................3-30
Exterior Lamps .............................................3-13 Brake System Warning Light ..........................3-31
Headlamps on Reminder ................................3-13 Anti-lock Brake System (ABS) Warning Light ....3-32
Daytime Running Lamps (DRL) .......................3-13 Speed Sensitive Power Steering (SSPS)
Fog Lamps ..................................................3-14 Warning Light ...........................................3-32
Instrument Panel Brightness ...........................3-15 Hold Mode Light ...........................................3-33
Dome Lamp .................................................3-15 Engine Coolant Temperature Gage ..................3-33
Map Lamps .................................................3-16 Tire Pressure Light .......................................3-34
Inadvertent Power Battery Saver .....................3-16 Malfunction Indicator Lamp .............................3-34
Accessory Power Outlet(s) .............................3-16 Oil Pressure Light .........................................3-38
Ashtray(s) and Cigarette Lighter ......................3-17 Fog Lamp Light ............................................3-38
Clock ..........................................................3-18 Cruise Control Light ......................................3-38
3-1
Section 3 Instrument Panel
Highbeam On Light .......................................3-39 Audio System(s) .............................................3-41
Daytime Running Lamps (DRL) Radio with CD (MP3/WMA) ............................3-42
Indicator Light ...........................................3-39 Radio with Six-Disc CD (MP3/WMA) ................3-48
Door Ajar Light .............................................3-39 Using an MP3 (Radio with CD Player) .............3-54
Trunk Ajar Light (Hatchback Only) ...................3-39 Using an MP3 (Radio with Six-Disc Player) ......3-58
Fuel Gage ...................................................3-40 Audio Steering Wheel Controls .......................3-61
Low Fuel Warning Light .................................3-40 Radio Reception ...........................................3-62
Care of Your CDs .........................................3-63
Care of the CD Player ...................................3-63
Integrated Windshield Antenna ........................3-63
3-2
NOTES
3-3
Instrument Panel Overview
3-4
The main components of the instrument panel are the following:
A. Air Outlets. See Outlet Adjustment on page 3-22. J. Horn. See Horn on page 3-6.
B. Instrument Panel Cluster. See Instrument Panel K. Cruise Control Buttons. See Cruise Control on
Cluster on page 3-25. page 3-10.
C. Hazard Warning Flashers Button. See Hazard L. Windshield Wiper Control. See Windshield Wipers
Warning Flashers on page 3-6. on page 3-8.
D. Digital Clock. See Clock on page 3-18. M. Climate Control System. See Climate Control
E. Audio System. See Audio System(s) on page 3-41. System on page 3-19.
F. Instrument Panel Brightness Control. See N. Ashtray. See Ashtray(s) and Cigarette Lighter on
Instrument Panel Brightness on page 3-15. page 3-17.
G. Hood Release. See Hood Release on page 5-11. O. Cigarette Lighter. See Ashtray(s) and Cigarette
Lighter on page 3-17.
H. Exterior Lamps Control. See Exterior Lamps on
page 3-13. P. Glove Box. See Glove Box on page 2-36.
I. Audio Steering Wheel Controls (If Equipped).
See Audio Steering Wheel Controls on page 3-61.
3-5
Hazard Warning Flashers Tilt Wheel
The hazard warning flashers let you warn the police and Your vehicle has a tilt wheel which lets you adjust the
others that you have a problem. The front and rear steering wheel before you drive.
turn signal lamps will flash on and off.
The hazard warning
flasher button is on the
instrument panel.
Press the button to make the front and rear turn signal
lamps flash on and off. Press again to turn the
flashers completely off.
The hazard warning flashers work even if the key is not
in the ignition switch.
Other Warning Devices The lever that lets you tilt the steering wheel is located
under the steering column.
If you carry reflective triangles, you can set them up at
the side of the road about 300 feet (100 m) behind To tilt the steering wheel, hold the wheel and push the
your vehicle. lever away from you. Then, move the wheel to a
comfortable position and pull the lever toward you to
Horn lock the wheel in place.
Press near or on the horn symbols on the steering Raise it to the highest level to give your legs more room
wheel pad to sound the horn. when you exit and enter the vehicle.
3-6
Turn Signal/Multifunction Lever Turn and Lane-Change Signals
The turn signal has two upward (for right) and
two downward (for left) positions. These positions let
you signal a turn or a lane change.
To signal a turn, move the lever all the way up or down.
An arrow on the instrument
panel cluster will flash in
the direction of the
turn or lane change.
Uplevel shown, Base similar
The lever on the left side of the steering column When the turn is finished, the lever will return
includes the following: automatically.
GTurn and Lane-Change Signals. See Turn To signal a lane change, raise or lower the lever until
and Lane-Change Signals on page 3-7. the arrow starts to flash. Hold it there until you complete
3Headlamp High/Low-Beam Changer. your lane change. The lever returns by itself when it
is released.
See Headlamp High/Low-Beam Changer on
page 3-8. As you signal a turn or a lane change, if the arrows
flash rapidly or do not go on at all, a signal bulb could
Flash-to-Pass. See Flash-to-Pass on page 3-8. be burned out and other drivers will not see your
OExterior Light Control. See Exterior Lamps on turn signal.
page 3-13.
Replace the bulb to help avoid an accident. If the arrow
-Fog Lamps, if equipped. See Fog Lamps on still does not flash when signaling, check the fuse.
page 3-14. See Fuses and Circuit Breakers on page 5-89.
3-7
Headlamp High/Low-Beam Changer Windshield Wipers
Push the turn signal/multifunction lever away from
you to change the headlamps from low beam to
high beam.
A light comes on in the
instrument panel cluster if
the high beams are on
while the ignition is turned
to ON/RUN.
To change the headlamps from high beam to low beam, Use this lever located on the right side of the steering
pull the turn signal lever toward you. wheel to operate the windshield wipers. The ignition
must be turned to ON/RUN to operate the windshield
Flash-to-Pass wipers.
This feature lets you use your high-beam headlamps to HI (High Speed): This position is for wiping at a high
signal a driver in front of you that you want to pass. speed.
To use it, pull the turn signal/multifunction lever toward LO (Low Speed): This position is for steady wiping at a
you until the high-beam headlamps come on, then low speed.
release the lever to turn them off.
3-8
INT (Intermittent): This position lets you choose a Windshield Washer
delayed wiping cycle. Turn the band on the windshield
wiper lever toward FAST or SLOW for a shorter or To wash the windshield, pull the windshield
longer delay between wipes. The wiper speed can only wiper/washer lever toward you while the ignition is
be adjusted when the lever is in the INT position. turned to ON/RUN.
OFF: This position turns off the windshield wipers.
Mist Function {CAUTION:

Move the lever toward, but not completely in, the INT
In freezing weather, do not use your washer
position for a single wiping cycle. Hold it there until the
windshield wipers start; then let go. The windshield until the windshield is warmed. Otherwise the
wipers stop after one wipe. If additional wiping cycles washer fluid can form ice on the windshield,
are needed, hold the lever toward INT longer. blocking your vision.
Remember that damaged wiper blades can prevent you
from seeing well enough to drive safely. To avoid When the lever is released, the washers stop, but the
damage, be sure to clear ice and snow from the wiper wipers continue to wipe for about two or three cycles
blades before using them. and either stop or resume at the previous speed.
If they are frozen to the windshield, carefully loosen or
thaw them. If the blades do become damaged, get
new blades or blade inserts.
Heavy snow or ice can overload the wiper motor.
A circuit breaker will stop the motor until it cools.
Clear away snow or ice to prevent an overload.
3-9
Rear Window Wiper/Washer Cruise Control
If your vehicle has cruise control, a speed of about
24 mph (39 km/h) or more can be maintained without
{CAUTION: keeping your foot on the accelerator. This can really help
on long trips. Cruise control does not work at speeds
In freezing weather, do not use your washer below 24 mph (39 km/h).
until the windshield is warmed. Otherwise the
washer fluid can form ice on the windshield,
blocking your vision. {CAUTION:
The vehicle has a rear window washer/wiper. Push the Cruise control can be dangerous where you
windshield wiper/washer lever toward the instrument cannot drive safely at a steady speed. So, do
panel to start the rear window washer/wiper system. not use your cruise control on winding roads
or in heavy traffic.
The wiper operates continuously when the lever is in the
first position. In some vehicle models, the wiper operates Cruise control can be dangerous on slippery
intermittently. roads. On such roads, fast changes in tire
Washer fluid sprays onto the rear window and the wiper traction can cause excessive wheel slip, and
operates continuously when the lever is pushed to you could lose control. Do not use cruise
the second position. control on slippery roads.
3-10
Setting Cruise Control 3. Press the SET button and release it. An indicator
light on the instrument panel cluster comes on to
show that the cruise control is on. See Cruise
{CAUTION: Control Light on page 3-38.
4. Take your foot off the accelerator pedal.
If you leave your cruise control on when you
are not using cruise, you might hit a button Resuming a Set Speed
and go into cruise when you do not want to. If the cruise control is set to a desired speed and then
You could be startled and even lose control. turned off by applying the brake or clutch pedal,
Keep the cruise control switch off until you if you have a manual transmission, this shuts off the
want to use cruise control. cruise control. However, it does not need to be
reset. Once you are going about 24 mph (39 km/h) or
more, briefly press the RESUME button.
The cruise control pad is
The vehicle will go back to the previously set speed and
located on the inboard
stay there.
side of the steering wheel.
If the RESUME button is held, the vehicle keeps going
faster until the button is released or you apply the
brake pedal. Do not hold the RESUME button, if you do
not want the vehicle speed to keep increasing.
1. Press the ON/OFF button to turn on the cruise

control.
2. Accelerate to the speed you want.
3-11
Increasing Speed While Using Cruise Passing Another Vehicle While Using
Control Cruise Control
There are two ways to go to a higher speed. Use the accelerator pedal to increase the vehicles
Use the accelerator pedal to get to a higher speed. speed. When you take your foot off the pedal, the vehicle
slows down to the cruise control speed set earlier.
Press the SET button, then release the button and
the accelerator pedal. The vehicle now cruises Using Cruise Control on Hills
at the higher speed.
How well the cruise control works on hills depends upon
Press the RESUME button. Hold it there until the the vehicle speed, load, and the steepness of the
desired speed is reached, and then release the hills. When going up steep hills, you might have to step
button. To increase the vehicle speed in very small on the accelerator pedal to maintain the vehicles
amounts, briefly press the RESUME button and speed. When going downhill, you might have to brake
then release it. Each time this is done, the vehicle or shift to a lower gear to keep the vehicles speed
goes about 1 mph (1.6 km/h) faster. down. Applying the brake pedal turns off the cruise
The accelerate feature will only work after the cruise control. Many drivers find this to be too much trouble
control is turned on by pressing the SET button. and do not use cruise control on steep hills.
Reducing Speed While Using Cruise Ending Cruise Control

Control There are two ways to turn off the cruise control:
There are two ways to reduce the vehicle speed while Step lightly on the brake pedal, or press the clutch
using cruise control: pedal, if the vehicle has a manual transmission.
Press the SET button until the desired lower speed Press the ON/OFF button on the cruise control pad.
is reached, then release it.
Erasing Speed Memory
To slow down in very small amounts, briefly press
the SET button. Each time this is done, the vehicle The cruise control set speed memory can be erased by
goes about 1 mph (1.6 km/h) slower. turning off the cruise control or the ignition.
3-12
Exterior Lamps ; (Parking Lamps): Turn the band to this position to
turn on the parking lamps, together with the taillamps,
license plate lamp, and instrument panel lights.
OFF: Turn the band to this position to turn all lamps off,
except the Daytime Running Lamps (DRL).
Headlamps on Reminder
If the drivers door is opened with the ignition turned to
LOCK/OFF or ACC/ACCESSORY and the lamps
are on, a warning chime will sound.
Uplevel shown, Base similar Daytime Running Lamps (DRL)

Daytime Running Lamps (DRL) can make it easier for
The lever on the left side of the steering column others to see the front of your vehicle during the
operates the exterior lamps. day. DRL can be helpful in many different driving
The exterior lamp band has three positions: conditions, but they can be especially helpful in the
short periods after dawn and before sunset.
3 (Headlamps): Turn the band to this position to turn
on the headlamps, together with the following: The DRL system will make your low-beam headlamps
come on in daylight when the following conditions
Taillamps are met:
License Plate Lamp The ignition is on.
Instrument Panel Lights
The exterior lamp band is in OFF or in the parking
Parking Lamps lamp position.
The headlamps automatically turn off when the ignition The parking brake is released.
key is turned to LOCK/OFF or ACC/ACCESSORY.
3-13
An indicator light will come on when the DRL are on. Fog Lamps
See Daytime Running Lamps (DRL) Indicator Light
on page 3-39. If your vehicle has fog lamps, use them for better
When the DRL system is on, the taillamps, sidemarker visibility in foggy or misty conditions.
lamps, parking lamps and instrument panel lights The band for the front fog lamps is located in the middle
will not be illuminated unless you have turned the of the turn signal/multifunction lever. While using the
exterior lamps control to the parking lamp or headlamp fog lamps, the ignition must be on as well as the parking
position. lamps or low-beam headlamps.
The DRL system will turn off when one of the following Turn the band to ON to turn the fog lamps on.
conditions are met: An indicator light will come on while the fog lamps
The ignition is off. are on. See Fog Lamp Light on page 3-38.
The parking brakes are on. Turn the band to OFF to turn the fog lamps off.
The fog lamps will also turn off while the high-beam
The high-beam headlamps are on.
headlamps are turned on. When the high-beam
The low-beam headlamps are on. headlamps are turned off, the fog lamps will turn
on again.
The flash-to-pass feature is used.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
3-14
Instrument Panel Brightness Dome Lamp
The thumbwheel for this The switch on this lamp
feature is located on the has three positions.
instrument panel to the left
of the steering wheel.
Turn the thumbwheel up to brighten the instrument ON: The light comes on and stays on regardless of
panel lights or down to dim them. whether a door is opened or closed.
O (Door): The light comes on while a door is opened.

After all of the doors are closed, the light stays on
for about seven seconds, and then fades out on the
Notchback/Wagon models. On the Hatchback model the
light will go off after the doors are closed. The light
will also turn off when the ignition is turned to ON/RUN.
OFF: The light remains off even when a door is opened.
3-15
Map Lamps Inadvertent Power Battery Saver
This feature is designed to protect your vehicles battery
against drainage from the taillamps, license plate
lamps, instrument panel lights, and parking lamps.
When the ignition is turned off, the power to these
features will automatically turn off after 5 seconds once
the drivers door is closed.
Accessory Power Outlet(s)

Accessory power outlets can be used to connect auxiliary
electrical equipment such as a cellular telephone or
CB radio.
One accessory power outlet is located on the front of
the center console below the front ashtray. For wagon
models, there may be another outlet in the rear luggage
compartment on the drivers side.
Your vehicle may have map lamps. To turn a lamp on, To use the outlet, remove the protective cap. When not
press the button next to it. Press the button again to in use, always cover the outlet with the protective cap.
turn it off. The accessory power outlet is operational when the
ignition is turned to ACC/ACCESSORY or ON/RUN.
3-16
Notice: Leaving electrical equipment on for Ashtray(s) and Cigarette Lighter
extended periods will drain the battery. Always turn
off electrical equipment when not in use and do not The front ashtray is located at the lower part of the
plug in equipment that exceeds the maximum center of the instrument panel. To remove the bin from
amperage rating. the front ashtray for cleaning, open the ashtray fully,
Certain electrical accessories may not be compatible lift up the inner bin and then pull the bin out.
with the accessory power outlet and could result The rear ashtray is located at the bottom of the rear
in blown vehicle or adapter fuses. If you experience a center console. Pull the ashtray toward the rear of the
problem, see your dealer/retailer for additional vehicle to open it. To remove the rear ashtray, press
information on the accessory power outlet. in the retaining spring and pull the bin out.
Notice: Adding any electrical equipment to your Notice: If you put papers, pins, or other flammable
vehicle may damage it or keep other components items in the ashtray, hot cigarettes or other smoking
from working as they should. The repairs would not materials could ignite them and possibly damage
be covered by your warranty. Do not use equipment your vehicle. Never put flammable items in the
exceeding maximum amperage rating of 20 amperes. ashtray.
Check with your dealer/retailer before adding
The cigarette lighter is located to the right of the front
electrical equipment.
ashtray. To use it, turn the ignition to ACC/ACCESSORY
When adding electrical equipment, be sure to follow or ON/RUN, push the cigarette lighter in all the way
the proper installation instructions included with and let go. When it is ready, it will pop back out by itself.
the equipment.
Notice: Holding a cigarette lighter in while it is
Notice: Improper use of the power outlet can cause heating will not allow the lighter to back away from
damage not covered by your warranty. Do not the heating element when it is hot. Damage from
hang any type of accessory or accessory bracket overheating may occur to the lighter or heating
from the plug because the power outlets are element. Do not hold a cigarette lighter in while it
designed for accessory power plugs only. is heating.
3-17
Clock M (Minute): To go forward one minute, press the
M button once. To go forward more than one minute,
Your vehicle has a digital clock. If you have a wagon, press and hold the button until the correct minute
the clock is located in the center of the instrument is reached.
panel below the air outlets. If you have a hatchback,
the clock is located in the center of the instrument panel S (Set): To reset the time to the nearest hour, press the
above the air outlets. When the ignition is turned to S button.
ACC/ACCESSORY or ON/RUN, the time is displayed in For example, if this button is pressed while the time is
the digital clock. There are three adjusting buttons for between 8:00 and 8:29, the display is set to 8:00. If this
the digital clock: button is pressed while the time is between 8:30 and
8:59, the display is set to 9:00.
After disconnecting the battery or replacing the fuse,
reset the clock.
H (Hour): To go forward one hour, press the H button

once. To go forward more than one hour, press and hold
the button until the correct hour is reached.
3-18
Climate Controls To change the current mode, select one of the following
from the middle knob:
Climate Control System E (Vent): This mode directs air to the instrument
panel outlets.
The heating, cooling and ventilation for your vehicle can
be controlled with this system. ( (Bi-Level): This mode splits the air between the
instrument panel outlets and the floor outlets.
5 (Floor): This mode directs most of the air to the floor

outlets. Some of the air will also be directed to the
windshield, instrument panel side outlets, and the rear
outlets. Be sure to keep the area under the front seats
clear to allow the flow of air to the rear compartment.
Temperature Control: Turn the right knob clockwise or
counterclockwise to manually increase or decrease the
temperature inside the vehicle. Turn the knob to the blue
area to get cool air and to the red area to get warm air.
Uplevel shown, Base similar A/C (Air Conditioning): If your vehicle has air
conditioning, follow these steps to use the system.
9 (Fan): Turn the left knob clockwise or Start the engine and set the fan control knob to
counterclockwise to increase or decrease the fan speed. the desired fan speed. The air conditioning compressor
In any setting other than off, the fan runs continuously does not operate when the fan control knob is turned
with the ignition in ON/RUN. The fan must be on for the to OFF. Press the A/C button to turn the air conditioning
air conditioning compressor to run. system on and off. When A/C is pressed, an indicator
light in the button comes on to show that the air
conditioning is activated.
3-19
On hot days, open the windows to let hot inside air ? (Recirculation): This mode keeps outside air
escape; then close them. This helps to reduce the time from coming into the vehicle. It can be used to prevent
it takes for the vehicle to cool down. It also helps the outside air and odors from entering the vehicle or to
system to operate more efficiently. help heat or cool the air inside the vehicle more quickly.
For quick cool down on hot days, do the following:
Press this button to turn the recirculation mode on.
1. Select the vent mode. When the button is pressed, an indicator light in
2. Select the highest fan speed. the button comes on. Press this button again to return
to outside air mode.
3. Press the A/C button.
Using the recirculation mode for extended periods may
4. Press the recirculation button. cause your windows to fog. If this happens, select
5. Select the coolest temperature. the defrost mode.
Using these settings together for long periods of time
may cause the air inside of the vehicle to become Defogging and Defrosting
too dry. To prevent this from happening, after the air in Fog on the inside of windows is a result of high humidity
the vehicle has cooled, turn the recirculation mode off. or moisture condensing on the cool window glass.
The air conditioning system removes moisture from This can be minimized if the climate control system is
the air, so a small amount of water might drip used properly. There are two modes to clear fog or frost
underneath the vehicle while idling or after turning off from the windshield. Use the defog mode to clear the
the engine. This is normal. windows of fog or moisture and warm the passengers.
Use the defrost mode to remove fog or frost from
the windshield more quickly.
3-20
(Defog): This mode directs most of the air to the Front Heated Windshield
windshield and the floor outlets. A small amount of air
is also directed to the outboard outlets for the side Your vehicle may have a heated front windshield which
windows and to the instrument panel side outlets. can be used with defog and defrost. This feature will
only work when the ignition is turned to ON/RUN.
When this mode is selected, the system runs the The front heated windshield uses a heated element to
air-conditioning compressor. To defog the windows remove fog or frost from the bottom of the windshield.
faster, turn the temperature control knob clockwise to
the warmest setting. < (Rear): Press this button located below the
audio system. An indicator light in the button comes
0 (Defrost): This mode directs most of the air to the
on to show that the feature is activated. The front
windshield and the outboard outlets for the side windshield heater will turn off about ten minutes after
windows. A small amount of air is also directed to the the button is pressed. To manually turn off the heater,
instrument panel side outlets. press the button again or turn off the engine. See Rear
When this mode is selected, the system runs the Window and Outside Mirror Defogger later in this
air-conditioning compressor. To defrost the windows section for more information on this button.
faster, turn the temperature control knob clockwise
to the warmest setting.
3-21
Rear Window and Outside Mirror Outlet Adjustment
Defogger Use the lever located in the center of each outlet to
Your vehicle may have a rear window and outside change the direction of the airflow. Use the thumbwheel
mirror defogger. This feature will only work when the located near the outlets to turn the airflow on or off.
ignition is turned to ON/RUN.
Operation Tips
The rear window defogger uses a warming grid to
remove fog or frost from the rear window. Before using Clear away any ice, snow or leaves from the air
this feature, clear as much snow from the rear inlets at the base of the windshield that may
window as possible. block the flow of air into the vehicle.
Use of non-GM approved hood deflectors may
< (Rear): Press this button. An indicator light in the adversely affect the performance of the system.
button comes on to show that the rear window defogger
is activated. Keep the path under the front seats clear of objects
to help circulate the air inside of the vehicle more
The rear window defogger will turn off about 10 minutes effectively.
after the button is pressed. To manually turn off the
defogger, press the button again or turn off the engine.
See Front Heated Windshield earlier in this section
for more information on this button.
Notice: Do not use anything sharp on the inside of
the rear window. If you do, you could cut or damage
the warming grid, and the repairs would not be
covered by your warranty. Do not attach a temporary
vehicle license, tape, a decal or anything similar to
the defogger grid.
3-22
Passenger Compartment Air Filter
Your vehicle may have a passenger compartment
air filter. It is located on the passenger side under the
glove box.
The filter traps most of the pollen from air entering the
module. The filter may need to be changed periodically.
To change the passenger compartment air filter, use
the following steps:
3. Remove the old passenger compartment air filter.

4. Reverse the steps to install the new air filter.
Make sure that the new filter is inserted to the
correct air flow.
1. Remove the four screws from the filter cover

located below the glove box.
2. Remove the filter cover.
3-23
Warning Lights, Gages, and Gages can indicate when there may be or is a problem
with one of your vehicles functions. Often gages
Indicators and warning lights work together to let you know when
there is a problem with your vehicle.
This section describes the warning lights and gages on
your vehicle. When one of the warning lights comes on and stays on
as you are driving, or when one of the gages shows
Warning lights and gages can signal that something is there may be a problem, check the section that tells you
wrong before it becomes serious enough to cause what to do about it. Follow this manuals advice.
an expensive repair or replacement. Paying attention to Waiting to do repairs can be costly and even dangerous.
the warning lights and gages could also save you or
others from injury.
Warning lights come on when there may be or is a
problem with one of your vehicles functions. Some
warning lights come on briefly when you start the engine
just to let you know they are working. If you are
familiar with this section, you should not be alarmed
when this happens.
3-24
Instrument Panel Cluster
Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know
how fast you are going, how much fuel you are using, and many other things you will need to drive safely and
economically.
Your vehicles instrument panel cluster includes indicator warning lights and gages that are explained on the
following pages.
3-25
Speedometer and Odometer Tachometer
The speedometer lets you see your vehicles speed The tachometer
in both miles per hour (mph) and kilometers per displays your engine
hour (km/h). speed in revolutions
per minute (rpm).
The odometer shows how far your vehicle has been
driven in kilometers.
Trip Odometer
The trip odometer can record the number of kilometers
traveled for up to two trips.
You can cycle between the odometer and trip
odometers A and B by pressing the reset button located Notice: If you operate the engine with the
in the lower right area of the speedometer. By pressing tachometer in the shaded warning area, your vehicle
the reset button, you can tell how many kilometers could be damaged, and the damages would not
have been recorded on either Trip A or Trip B since you be covered by your warranty. Do not operate
last set the trip odometer back to zero. the engine with the tachometer in the shaded
warning area.
To reset each trip odometer to zero, press and hold the
reset button. The reset button resets only the trip
odometer that is displayed. Each trip odometer must be
reset individually.
3-26
Safety Belt Reminders Airbag Readiness Light
Safety Belt Reminder Light There is an airbag readiness light on the instrument
panel cluster, which shows the airbag symbol.
The safety belt light will The system checks the airbags electrical system for
come on when the engine malfunctions. The light tells you if there is an electrical
is started and stay on problem. The system check includes the airbag sensor,
until the drivers safety belt the airbag modules, the wiring and the crash sensing
is buckled. and diagnostic module. For more information on
the airbag system, see Airbag System on page 1-51.
This light will come on

when you start your
If the drivers belt is already buckled, the light will not vehicle, and it will flash for
come on. a few seconds. The light
should go out and the
Safety Belt Reminder Tone system is ready.
If your vehicle has this feature, a tone will sound for

several seconds when the engine is started to remind
people to fasten their safety belts. The tone will not
sound if the drivers safety belt is already buckled.
3-27
If the airbag readiness light stays on after you start the Passenger Airbag Status Indicator
vehicle or comes on when you are driving, your airbag
system may not work properly. Have your vehicle Your vehicle has the passenger sensing system. Your
serviced right away. vehicle has a passenger airbag status indicator in the
clock, located in the center of the instrument panel.
{CAUTION: When you start the

vehicle, the passenger
airbag status indicator will
If the airbag readiness light stays on after you light for several seconds
start your vehicle, it means the airbag system as a system check.
may not be working properly. The airbags in
your vehicle may not inflate in a crash, or they
could even inflate without a crash. To help
avoid injury to yourself or others, have your Then, after several more seconds, if the off symbol is lit
vehicle serviced right away if the airbag on the passenger airbag status indicator, it means
readiness light stays on after you start your that the passenger sensing system has turned off the
vehicle. right front passengers frontal airbag and seat-mounted
side impact airbag (if equipped). See Passenger
Sensing System on page 1-59 for more on this, including
The airbag readiness light should flash for a few seconds important safety information.
when the engine is started. If the light does not come on
then, have it fixed so it will be ready to warn you if there is
a problem.
3-28
{CAUTION: {CAUTION:
If the on indicator comes on when you have a Even though the passenger sensing system is
rear-facing child restraint installed in the right designed to turn off the right front passengers
front passengers seat, it means that the frontal airbag and seat-mounted side impact
passenger sensing system has not turned airbag (if equipped) if the system detects a
off the passengers frontal airbag and rear-facing child restraint, no system is
seat-mounted side impact airbag (if equipped). fail-safe, and no one can guarantee that an
A child in a rear-facing child restraint can be airbag will not deploy under some unusual
seriously injured or killed if the right front circumstance, even though it is turned off.
passengers airbag inflates. This is because We recommend that rear-facing child restraints
the back of the rear-facing child restraint be secured in a rear seat, even if the airbag is
would be very close to the inflating airbag. or airbags are off.
Do not use a rear-facing child restraint in the
right front passengers seat if the airbag is
turned on.
3-29
If the off symbol is not lit on the passenger airbag status Charging System Light
indicator, it means that the right front passengers
frontal airbag and seat-mounted side impact airbag
This light will come on
(if equipped) are enabled (may inflate).
briefly when the ignition
is turned on, and the
engine is not running,
{CAUTION: as a check to show you it
is working.
If the airbag readiness light in the instrument
panel cluster ever comes on and stays on, it
means that something may be wrong with the It should go out when the engine is started. If it stays
airbag system. If this ever happens, have the on, or comes on while you are driving, you may have a
vehicle serviced promptly, because an problem with the electrical charging system. Have it
adult-size person sitting in the right front checked by your dealer/retailer. Driving while this light is
passengers seat may not have the protection on could drain your battery. If you must drive a short
of the airbag(s). See Airbag Readiness Light distance with the light on, be certain to turn off all your
on page 3-27 for more on this, including accessories, such as the radio and air conditioner to
help reduce the drain on the battery.
important safety information.
3-30
Brake System Warning Light If the light comes on while you are driving, pull off the
road and stop carefully. You may notice that the pedal is
Your vehicles hydraulic brake system is divided into harder to push. Or, the pedal may go closer to the
two parts. If one part is not working, the other part can floor. It may take longer to stop. If the light is still on,
still work and stop you. For good braking, though, have the vehicle towed for service. See Towing
you need both parts working well. Your Vehicle on page 4-23.
If the warning light comes on, there is a brake problem.
Have your brake system inspected right away.
{CAUTION:
This light should come on
briefly when you turn the Your brake system may not be working
ignition to ON/RUN.
properly if the brake system warning light is
If it does not come on then,
have it fixed so it will be on. Driving with the brake system warning light
ready to warn you if on can lead to an accident. If the light is still
there is a problem. on after you have pulled off the road and
stopped carefully, have the vehicle towed
for service.
When the ignition is on, the brake system warning light
will also come on when you set your parking brake.
The light will stay on if your parking brake does not fully
release. If it stays on after your parking brake is fully
released, it means you have a brake problem.
3-31
Anti-lock Brake System (ABS) Speed Sensitive Power Steering
Warning Light (SSPS) Warning Light
For vehicles with the If your vehicle has Speed
Antilock Brake System Sensitive Power Steering,
(ABS), this light will this warning light will
come on briefly when come on briefly when you
the engine is started. turn the ignition to
ON/RUN as a check to
show you it is working.
If it does not come on have your vehicle serviced. Then it should go out after a few seconds.
If the light stays on, turn the ignition to LOCK/OFF. If the warning light does not come on, have it fixed so it
If the light comes on, stop as soon as possible and turn will be able to warn you if there is a problem.
the ignition off. Then start the engine again to reset If the warning light stays on, or comes on while you are
the system. If the light still stays on, or comes on again driving, the system may not be working. If this
while you are driving, your vehicle needs service. happens, see your dealer/retailer for service.
See your dealer/retailer. If the regular brake system
warning light is not on, you still have brakes, but you do
not have antilock brakes. If the regular brake system
warning light is also on, you do not have antilock brakes
and there is a problem with your regular brakes.
See Brake System Warning Light on page 3-31.
3-32
Hold Mode Light Engine Coolant Temperature Gage
If your vehicle has Your vehicle has an
this feature, this light engine coolant temperature
comes on when the gage. With the ignition
hold mode is active. turned to ON/RUN,
this gage shows the engine
coolant temperature.
If the HOLD mode light flashes, have your vehicle

checked. See Hold Mode under Automatic
Transmission Operation on page 2-22 for more
information.
If the gage pointer moves into the red area, your engine
is too hot. It means that your engine coolant has
overheated.
If you have been operating your vehicle under normal
driving conditions, you should pull off the road, stop your
vehicle and turn off the engine as soon as possible.
See Engine Overheating on page 5-22.
3-33
Tire Pressure Light Malfunction Indicator Lamp
This light comes on briefly Check Engine Light
when you turn the ignition
to ON/RUN. A computer system called OBD II (On-Board
Diagnostics-Second Generation) monitors operation of
the fuel, ignition, and emission control systems. It makes
sure that emissions are at acceptable levels for the life of
the vehicle, helping to produce a cleaner environment.
The check engine light
comes on to indicate
that there is an OBD II
problem and service
is required.
This light will also come on when one or more of your

tires are significantly underinflated.
Stop and check your tires as soon as it is safe to do so. Malfunctions often are indicated by the system before
If underinflated, inflate to the proper pressure. any problem is apparent. This can prevent more serious
See Tires on page 5-49 for more information. damage to your vehicle. This system is also designed
to assist your service technician in correctly diagnosing
This light will flash for about one minute and then stay any malfunction.
on if a problem is detected with the Tire Pressure
Monitor system.
See Tire Pressure Monitor System on page 5-57 for
more information.
3-34
Notice: If you keep driving your vehicle with this When the ignition is turned to ON/RUN, this light comes
light on, after a while, the emission controls on and should go out after a few seconds as a check
might not work as well, your vehicles fuel economy to show it is working. If the light does not come on, have
might not be as good, and the engine might not it repaired. This light also comes on during a malfunction
run as smoothly. This could lead to costly repairs in one of two ways:
that might not be covered by your warranty. Light Flashing A misfire condition has been
Notice: Modifications made to the engine, detected. A misfire increases vehicle emissions
transmission, exhaust, intake, or fuel system of and could damage the emission control system on
your vehicle or replacement tires that do not your vehicle. Diagnosis and service might be
match your vehicles original tires can affect your required.
vehicles emission controls and can cause this light Light On Steady An emission control system
to come on. Modifications to these systems could malfunction has been detected on your vehicle.
lead to costly repairs not covered by your warranty. Diagnosis and service might be required.
This could also result in a failure to pass a
required Emission Inspection/Maintenance test.
See Accessories and Modifications on page 5-4.
3-35
If the Light Is Flashing If the Light Is On Steady
The following can prevent more serious damage to You might be able to correct the emission system
your vehicle: malfunction by considering the following:
Reduce vehicle speed. Did you recently put fuel into your vehicle?
Avoid hard accelerations. If so, reinstall the fuel cap, making sure to fully
install the cap. See Filling the Tank on page 5-8.
Avoid steep uphill grades. The diagnostic system can determine if the fuel cap
If the light stops flashing and remains on steady, has been left off or improperly installed. A loose
see If the Light Is On Steady following. or missing fuel cap allows fuel to evaporate into the
atmosphere. A few driving trips with the cap properly
If the light continues to flash, when it is safe to do so,
installed should turn the light off.
stop the vehicle. Find a safe place to park your vehicle.
Turn the key off, wait at least 10 seconds and restart Did you just drive through a deep puddle of water?
the engine. If the light remains on steady, see If the If so, your vehicles electrical system might be wet.
Light Is On Steady following. If the light is still flashing, The condition is usually corrected when the electrical
follow the previous steps, and see your dealer/retailer system dries out. A few driving trips should turn the
for service as soon as possible. light off.
3-36
Have you recently changed brands of fuel? Emissions Inspection and
If so, be sure to fuel your vehicle with quality fuel. Maintenance Programs
See Gasoline Octane on page 5-6. Poor fuel quality
causes the engine not to run as efficiently as Some state/provincial and local governments have or
designed. You might notice this as stalling after might begin programs to inspect the emission control
start-up, stalling when you put the vehicle into gear, equipment on your vehicle. Failure to pass this
misfiring, hesitation on acceleration, or stumbling on inspection could prevent you from getting a vehicle
acceleration these conditions might go away once registration.
the engine is warmed up. This will be detected by Here are some things you need to know to help your
the system and cause the light to turn on. vehicle pass an inspection:
If you experience one or more of these conditions, Your vehicle will not pass this inspection if the check
change the fuel brand you use. It will require at least engine light is on or not working properly.
one full tank of the proper fuel to turn the light off.
Your vehicle will not pass this inspection if the OBD
If none of the above steps have made the light turn off, (on-board diagnostic) system determines that critical
your dealer/retailer can check the vehicle. Your emission control systems have not been completely
dealer/retailer has the proper test equipment and diagnosed by the system. The vehicle would be
diagnostic tools to fix any mechanical or electrical considered not ready for inspection. This can happen
problems that might have developed. if you have recently replaced the battery or if the battery
has run down. The diagnostic system is designed to
evaluate critical emission control systems during normal
driving. This can take several days of routine driving.
If you have done this and your vehicle still does not pass
the inspection for lack of OBD system readiness, your
dealer/retailer can prepare the vehicle for inspection.
3-37
Oil Pressure Light Fog Lamp Light
The fog lamp light will
{CAUTION: come on when the fog
lamps are in use.
Do not keep driving if the oil pressure is low.

If you do, your engine can become so hot that
it catches fire. You or others could be burned.
Check your oil as soon as possible and have
your vehicle serviced. The light will go out when the fog lamps are turned off.
See Fog Lamps on page 3-14 for more information.
Notice: Lack of proper engine oil maintenance may
damage the engine. The repairs would not be covered
Cruise Control Light
by your warranty. Always follow the maintenance
If your vehicle has cruise
schedule in this manual for changing engine oil.
control, this light comes on
This light will come on whenever you set your
briefly when you start your cruise control.
engine as a check to be
sure it works. If it does not,
have your vehicle serviced.
The light will go out when the cruise control is

turned off. See Cruise Control on page 3-10 for more
If the light comes on and stays on, it means that oil is not information.
flowing through your engine properly. You could be low
on oil and you might have some other system problem.
3-38
Highbeam On Light Door Ajar Light
This light comes on when This light will stay on until
the high-beam headlamps all doors are closed and
are in use. completely latched.
See Headlamp High/Low-Beam Changer on page 3-8

Daytime Running Lamps (DRL)

If the key is in the ignition while the drivers door is
Indicator Light open, you will also hear a warning chime.
This light turns on Trunk Ajar Light (Hatchback Only)
whenever the Daytime
Running Lamps are on. This light will come on
when the trunk is not
completely closed.
See Daytime Running Lamps (DRL) on page 3-13 for

more information.
3-39
Fuel Gage The indicator moves a little when you turn a corner or
speed up.
Your fuel gage tells you
about how much fuel The gage goes back to empty when you turn off the
you have left when ignition.
the ignition is turned to
ON/RUN. Low Fuel Warning Light
This light comes on when
the fuel tank is low on fuel.
When the tank nears empty, the low fuel warning light
will come on. You still have a little fuel left, but you
should get more soon. See Low Fuel Warning Light on The low fuel warning light comes on when there is
page 3-40 for more information. about 2.0 gallons (7.5 liters) of fuel remaining in
Here are four things that some owners ask about. the tank.
None of these show a problem with your fuel gage: To turn the light off, add fuel to the fuel tank. See Filling
At the service station, the gas pump shuts off before the Tank on page 5-8.
the gage reads full.
It takes a little more or less fuel to fill up than the
gage indicated. For example, the gage may have
indicated the tank was half full, but it actually took a
little more or less than half the tanks capacity to fill
the tank.
3-40
Audio System(s) While your vehicle is parked:
Familiarize yourself with all of its controls.
Determine which radio your vehicle has and then read
the pages following to familiarize yourself with its Familiarize yourself with its operation.
features. Set up your audio system by presetting your
favorite radio stations, setting the tone, and
adjusting the speakers. Then, when driving
{CAUTION: conditions permit, you can tune to your favorite
radio stations using the presets and steering wheel
This system provides you with far greater controls if the vehicle has them.
access to audio stations and song listings. Notice: Before adding any sound equipment to
Giving extended attention to entertainment your vehicle, such as an audio system, CD player,
tasks while driving can cause a crash and you CB radio, mobile telephone, or two-way radio,
or others can be injured or killed. Always keep make sure that it can be added by checking with
your eyes on the road and your mind on the your dealer/retailer. Also, check federal rules
drive avoid engaging in extended searching covering mobile radio and telephone units.
If sound equipment can be added, it is very
while driving.
important to do it properly. Added sound equipment
may interfere with the operation of your vehicles
Keeping your mind on the drive is important for safe engine, radio, or other systems, and even damage
driving. See Defensive Driving on page 4-2. Here are them. Your vehicles systems may interfere with
some ways in which you can help avoid distraction while the operation of sound equipment that has been
driving. added.
3-41
Radio with CD (MP3/WMA) The previous volume setting is maintained whenever the
radio is turned on. The volume can be adjusted by
using the volume knob.
Finding a Station
AM: Press this button to switch to an AM station.
The display shows the selection.
FM: Press this button to switch to an FM station.
( ) TUNE: Press the TUNE arrows to select radio
stations.
Press the up TUNE arrow to increase or the down
TUNE arrow to decrease the radio frequencies.
SEEK: Press the SEEK arrows to seek radio
stations.
Playing the Radio
Press the up SEEK arrow to seek the next radio station or
O(Power/Volume): Press and release this knob to the down SEEK arrow to seek the previous radio station.
turn the system on. Press and hold this knob for
more than two seconds to turn the system off. SCAN/AST: Press this button to scan radio stations.
The radio goes to a station, plays for a few seconds,
Turn this knob clockwise or counterclockwise to increase then goes to the next station. Press this button again to
or decrease the volume. stop scanning.
When the system is on, press and release this knob to The radio scans stations only with a strong signal that
mute the system. Press and release this knob again are in the selected band.
to turn the sound back on.
3-42
AST (Automatic Store) Order of Sound Function
Six FM1 preset stations with the strongest reception in The order for displayed sound function is BASS, TRE,
the region can be automatically stored. Press the BAL, FADE, EQ OFF, and VOL (Bass, Treble, Fade,
AST button for more than two seconds. The display Balance, Equalization Off, and Volume).
shows AUTO SCANNING and then SCANNING flashes
on the display. Once the stations are stored, the radio Setting the Tone (Bass/Treble)
switches to FM1 and the first preset station begins
to play. FM-A displays while listening to the automatic SOUND (Bass/Treble): Press this button until BAS
stored stations. Press the AM or FM button to cancel (bass) displays. Turn the Oknob to increase or to
automatic store. decrease the bass. The display shows the bass level.
After making the selection, press this button to set
Setting Preset Stations the bass level selection.
Up to 24 stations (six FM1, six FM2, six AM1, and Press this button until TRE (treble) displays.
six AM2), can be programmed on the six numbered Turn the Oknob to increase or to decrease the treble.
buttons, by performing the following steps: The display shows the treble level. After making the
1. Turn the radio on. selection, press this button to set the treble level
2. Press the AM or FM button to select FM1, FM2, selection. If a station is weak or has static, decrease
AM1 or AM2. the treble.
3. Tune in the desired station.
4. Press and hold one of the six numbered buttons for
more than two seconds. The preset button number
one through six flashes on the display when the
station has been set. When that numbered preset
button is pressed, that preset station returns.
5. Repeat the Steps 1 through 4 for each preset button.
3-43
Adjusting the Speakers (Balance/Fade) To cancel an equalization setting, press the SOUND
button until EQ OFF displays, turn the Oknob until OFF
SOUND (Balance/Fade): To adjust the balance displays, then press the SOUND button again to set the
between the right and the left speakers, press this button equalization setting.
until BAL (balance) displays. Turn the O knob to
increase or to decrease. The display shows the balance Playing a CD
level. After making the selection, press this button to
set the balance level. Insert a CD partway into the slot, label side up.
The player pulls it in and the CD should begin playing.
To adjust the fade between the front and the rear
speakers, press this button until FAD (fade) displays. When a CD is inserted, CDP displays. As the CD is
loading, Filecheck displays. As each new track starts to
Turn the Oknob to increase or to decrease the fade play, Track and the track number displays.
between the front and the rear speakers. The display
shows the fade level. After making the selection, press If the ignition or radio is turned off with a CD in the
this button to set the fade level. player, it stays in the player. When a CD is in the player
and the ignition is turned on, the radio must be turned
Setting the Equalization on before the CD starts playback. When the ignition
and radio are turned on, the CD starts playing where it
The order for displayed customized equalization settings stopped, if it was the last selected audio source.
are EQ OFF, CLASSIC, DANCE, ROCK, JAZZ, POP,
VOICE, TECHNO, EQ OFF. The CD player can play the smaller 3 inch (8 cm)
single CDs with an adapter ring. Full-size CDs and the
SOUND (Equalization): Press this button until EQ OFF smaller CDs are loaded in the same manner.
(equalization) displays to select customized equalization
If playing a CD-R, the sound quality can be reduced
settings designed for classic, dance, rock, jazz, pop,
due to CD-R quality, the method of recording, the quality
voice and techno. Turn the Oknob until the desired of the music that has been recorded, and the way the
equalization setting displays. After making the selection, CD-R has been handled. There can be an increase
press the SOUND button to set the equalization setting. in skipping, difficulty in finding tracks, and/or difficulty
3-44
in loading and ejecting. If these problems occur, check 2 RPT (Repeat): Press this button to repeat the
the bottom surface of the CD. If the surface of the current track. RPT displays. Press this button again to
CD is damaged, such as cracked, broken, or scratched, turn off repeat play.
the CD will not play properly. If the surface of the CD
is soiled, see Care of Your CDs on page 3-63 for more 3 RDM (Random): Press this button to hear the
information. tracks in random, rather than sequential, order.
RDM displays. Press this button again to turn off
If there is no apparent damage, try a known good CD. random play.
Do not add any label to a CD, it could get caught in the
4 INT (Scan): Press this button to listen to the first
CD player. If a CD is recorded on a personal computer
few seconds of each track on each loaded CD.
and a description label is needed, try labeling the top of
INTRO displays. To stop scanning press this button
the recorded CD with a marking pen.
again. The current track begins to play.
Notice: If a label is added to a CD, or more than
one CD is inserted into the slot at a time, or an ( ) TUNE (Previous/Next Track): Press the up
attempt is made to play scratched or damaged CDs, TUNE arrow to go to the next track. The track number
the CD player could be damaged. While using the displays. Press the down TUNE arrow to go to the
CD player, use only CDs in good condition without start of the current track. The player continues moving
any label, load one CD at a time, and keep the forward or backward through the CD with each press of
CD player and the loading slot free of foreign the up or down arrows.
materials, liquids, and debris.
AM: Press this button to listen to the radio while a CD
If an error displays, see CD Messages later in this is playing. The inactive CD remains inside the radio
section. for future listening.
3-45
FM: Press this button to listen to the radio while a CD CD Messages
is playing. The inactive CD remains inside the radio
for future listening. CHECK CD: If this message displays and/or the CD
comes out, it could be for one of the following reasons:
CD/AUX: Press this button to play a CD while listening
to the radio. CDP displays when the CD player has It is very hot. When the temperature returns to
been selected. The CD symbol displays when a normal, the CD should play.
CD is loaded. You are driving on a very rough road. When the
Press this button while a CD is playing to pause the road becomes smoother, the CD should play.
CD. PAUSE flashes on the display. Press this button The CD is dirty, scratched, wet, or upside down.
again to start playing the CD.
The air is very humid. If so, wait about an hour
EJECT: Press this button to eject a CD. This is the and try again.
only way a CD can be ejected from the player. The CD The format of the CD might not be compatible.
can eject when the ignition or the radio is turned off. See Using an MP3 (Radio with CD Player) on
page 3-54 or Using an MP3 (Radio with Six-Disc
Playing an MP3/WMA CD-R Disc Player) on page 3-58 later in this section.
If you have a radio with a single CD (MP3), it is capable There could have been a problem while burning
of playing an MP3/WMA CD-R disc. For more the CD.
information on how to play an MP3/WMA CD-R disc,
see Using an MP3 in the index.
The label could be caught in the CD player.
If the CD is not playing correctly, for any other reason,
try a known good CD.
If any error occurs repeatedly or if an error cannot be
corrected, contact your dealer/retailer. If the radio
displays an error message, write it down and provide it
to your dealer/retailer when reporting the problem.
3-46
Using the Auxiliary Input Jack To use a portable audio player, connect a 3.5 mm
(1/8 inch) cable to the radios front auxiliary input jack.
AUX IN (Auxiliary Input): The radio system has an While a device is connected, turn the portable audio
auxiliary input jack located on the lower right side of the player on and press the radio CD/AUX button to
faceplate. This is not an audio output. Do not plug hear audio from the device over the vehicle speakers.
the headphone set into the front auxiliary input jack.
An external audio device such as an iPod, laptop CD/AUX (CD/Auxiliary): Press this button once to play
computer, MP3 player, CD changer, or cassette tape a CD while a portable audio device is playing. Press
player, etc. can be connected to the auxiliary input jack this button a second time for the system to begin
for use as another source for audio listening. playing audio from the connected portable audio player.
Once in this mode, Auxinput appears on the display.
The auxiliary input jack also accepts cell phone If the auxiliary jack does not detect the presence of an
connectors. Plug the cell phone connector into the output jack, the auxiliary mode does not display.
auxiliary input jack to hear a person speaking on a cell
phone during conversation through the vehicle sound O(Power/Volume): Turn the Oknob clockwise or
system. counterclockwise to increase or decrease the volume
of the portable player. Additional adjustments on a
Drivers are encouraged to set up any auxiliary device portable device might be needed to get the desired
while the vehicle is in PARK (P). See Defensive Driving volume.
on page 4-2 for more information on driver distraction.
3-47
Radio with Six-Disc CD (MP3/WMA) The previous volume setting is maintained whenever the
radio is turned on. The volume can be adjusted by
using the volume knob.
Finding a Station
AM: Press this button to switch to an AM station.
FM: Press this button to switch to an FM station.
( ) TUNE: Press the TUNE arrows to select radio

stations.
Press the up TUNE arrow to increase or the down
TUNE arrow to decrease the radio frequencies.
SEEK: Press the SEEK arrows to seek radio
stations.
Playing the Radio
Press the up SEEK arrow to seek the next radio station
O(Power/Volume): Press and release this knob to or the down SEEK arrow to seek the previous radio
turn the system on. Press and hold this knob for station.
more than two seconds to turn the system off.
SCAN/AST: Press this button to scan radio stations.
Turn this knob clockwise or counterclockwise to increase The radio goes to a station, plays for a few seconds,
or decrease the volume. then goes to the next station. Press this button again to
When the system is on, press and release this knob to stop scanning.
mute the system. Press and release this knob again The radio only scans stations with a strong signal that
to turn the sound back on. are in the selected band.
3-48
AST (Automatic Store) Order of Sound Function
Six FM1 preset stations with the strongest reception in The order for displayed sound function is BASS, TRE,
the region can be automatically stored. Press the FAD, BAL, EQ OFF, and VOL (Bass, Treble, Fade,
AST button for more than one second. The display Balance, Equalization Off, and Volume).
shows AUTO SCANNING and then SCANNING flashes
on the display. Once the stations are stored, the Setting the Tone
radio switches to FM1 and the first preset station begins
to play. FM-A displays while listening to the automatic (Bass/Midrange/Treble)
stored stations. Press the AM or FM button to cancel
SOUND (Bass/Midrange/Treble): Press this button
automatic store.
until BAS (bass) displays. Turn the Oknob to increase
Setting Preset Stations or to decrease the bass. The display shows the bass
level. After making the selection, press this button
Up to 36 stations (six FM1, six FM2, six FM-A, six AM1, to select the bass level.
six AM2, and six AM-A), can be programmed on the
six numbered buttons, by performing the following steps: Press this button until MID (midrange) displays.
1. Turn the radio on. Turn the Oknob to increase or to decrease the
midrange. The display shows the midrange level.
2. Press the AM or FM button to select FM1, FM2, After making the selection, press this button to select
FM-A, AM1, AM2, or AM-A. the midrange level.
3. Tune in the desired station.
Press this button until TRE (treble) displays.
4. Press and hold one of the six numbered pushbuttons Turn the Oknob to increase or to decrease the treble.
for more than two seconds. The channel number
The display shows the treble level. After making the
(CH#1 through CH#6) flashes on the display when
selection, press this button to select the treble level.
the station has been set. When that numbered preset
If a station is weak or has static, decrease the treble.
button is pressed, that preset station returns.
5. Repeat the Steps 1 through 4 for each preset button.
3-49
Adjusting the Speakers (Balance/Fade) Order of Sound Function
SOUND (Balance/Fade): To adjust the balance The order for displayed sound function is EQ OFF,
between the right and the left speakers, press this button CLASSIC, DANCE, ROCK, JAZZ, POP, VOICE,
until BAL (balance) displays. Turn the Oknob to TECHNO, and EQ OFF.
increase or to decrease the balance. The display shows
the balance level. After making the selection, press Playing a CD(s)
this button to select the balance level. LOAD: Press this button to load CDs into the CD player.
This CD player holds up to six CDs.
To adjust the fade between the front and the rear
speakers, press this button until FAD (fade) displays. 1. Press and release the load button. A message to
Turn the Oknob to increase or to decrease the fade select a slot number from 1 through 6 displays.
between the front and the rear speakers. The display 2. Press the desired slot number. Wait for the
shows the fade level. After making the selection, press message to insert the disc.
this button to select the fade level.
3. Load a CD. Insert the CD partway into the slot,
Setting the EQ (Equalization) label side up. The player pulls the CD in.
To insert multiple CDs, do the following:
SOUND (Equalization): Press this button until EQ OFF
(equalization) displays to select customized equalization 1. Press and hold the load button for two seconds.
settings designed for classic, dance, rock, jazz, pop, A beep sounds and a message to load multiple
voice, and techno. Turn the Oknob until the desired discs displays.
equalization setting displays. After making the selection, 2. Follow the displayed instruction on when to insert
press the SOUND button to select the equalization the discs. The CD player takes up to six CDs.
setting. 3. Press the LOAD button again to cancel loading
To cancel an equalization setting, press the SOUND more CDs.
button until EQ OFF displays. Turn the Oknob until OFF As each CD is inserted, CDP displays. As each CD is
displays, then press the SOUND button again to select loading, Filecheck displays.
the equalization setting.
3-50
Once playback begins, the track and track number Do not add any label to a CD, it could get caught in the
displays. CD player. If a CD is recorded on a personal computer
If the ignition or radio is turned off with a CD in the
player, it stays in the player. While a CD is in the player
and the ignition is turned on, the radio must be turned Notice: If a label is added to a CD, or more than
on before the current CD starts playback. When the one CD is inserted into the slot at a time, or an
ignition and radio are turned on, the CD starts playing attempt is made to play scratched or damaged CDs,
where it stopped, if it was the last selected audio source. the CD player could be damaged. While using the
The CD player can play the smaller 3 inch (8 cm) CD player, use only CDs in good condition without
single CDs with an adapter ring. Full-size CDs and the any label, load one CD at a time, and keep the
smaller CDs are loaded in the same manner. CD player and the loading slot free of foreign
materials, liquids, and debris.
If playing a CD-R, the sound quality can be reduced
due to CD-R quality, the method of recording, the quality If an error displays, see CD Messages later in this
of the music that has been recorded, and the way the section.
CD-R has been handled. There can be an increase 2 RPT (Repeat): Press this button to repeat the current
in skipping, difficulty in finding tracks, and/or difficulty in track. RPT displays. Press this button again to turn
loading and ejecting. If these problems occur, check off repeat play.
the bottom surface of the CD. If the surface of the CD is
damaged, such as cracked, broken, or scratched, the 3 RDM (Random): Press this button to hear the tracks
CD does not play properly. If the surface of the CD in random, rather than sequential, order. RDM displays.
is soiled, see Care of Your CDs on page 3-63 for more
information. Press this button again to turn off random play.
If there is no apparent damage, try a known good CD.
3-51
4 INT (Scan): Press this button to listen to the first CD/AUX: Press this button to play a CD while listening
few seconds of each track on each loaded CD. to the radio. CDP displays when the CD player has
INTRO displays. To stop scanning press this button been selected. The CD symbol displays when a CD is
again. The current track begins to play. loaded.
5 CDC (Previous CDC): Press this button to go back Press this button while a CD is playing to pause the
to the start of the previous CDC. CD. PAUSE flashes on the display. Press this button
again to start playing the CD.
6 CDC + (Next CDC): Press this button to go forward
to the start of the next CDC. EJECT: Press this button to eject the CD. Press and
hold this button to eject all CDs. This is the only way
( ) TUNE (Previous/Next Track): Press the up a CD can be ejected from the player. The CD can eject
TUNE arrow to go to the next track. The track number when the ignition or the radio is turned off.
displays. Press the down TUNE arrow to go to the
start of the current track. The player continues moving Playing an MP3/WMA CD-R Disc
forward or backward through the CD with each press of
the up or down arrows. If your vehicle has a radio with a six-disc CD player,
it is capable of playing an MP3/WMA CD-R disc.
AM: Press this button to listen to the radio while a CD For more information on how to play an MP3/WMA disc,
is playing. The inactive CD remains inside the radio see Using an MP3 in the index.
for future listening.
FM: Press this button to listen to the radio while a
CD is playing. The inactive CD remains inside the radio
for future listening.
3-52
CD Messages Using the Auxiliary Input Jack
CHECK CD: If this message displays and/or the CD AUX IN (Auxiliary Input): The radio system has an
comes out, it could be for one of the following reasons: auxiliary input jack located on the lower right side of the
It is very hot. When the temperature returns to faceplate. This is not an audio output. Do not plug
normal, the CD should play. the headphone set into the front auxiliary input jack.
An external audio device such as an iPod, laptop
You are driving on a very rough road. When the computer, MP3 player, CD changer, or XM receiver,
road becomes smoother, the CD should play. etc. can be connected to the auxiliary input jack for
The CD is dirty, scratched, wet, or upside down. use as another source for audio listening.
The air is very humid. If so, wait about an hour The auxiliary input jack also accepts cell phone
and try again. connectors. Plug the cell phone connector into the
auxiliary input jack to hear a person speck on a
The format of the CD might not be compatible. cell phone during a conversation through the vehicle
See Using an MP3 later in this section. sound system.
There could have been a problem while burning Drivers are encouraged to set up any auxiliary device
the CD. while the vehicle is in PARK (P). See Defensive Driving
The label could be caught in the CD player. on page 4-2 for more information on driver distraction.
If the CD is not playing correctly, for any other reason,
try a known good CD.
If any error occurs repeatedly or if an error cannot be
corrected, contact your dealer/retailer. If the radio
displays an error message, write it down and provide it
to your dealer/retailer when reporting the problem.
3-53
To use a portable audio player, connect a 3.5 mm Using an MP3
(1/8 inch) cable to the radios front auxiliary input jack.
While a device is connected, turn the portable audio (Radio with CD Player)
player on and press the radio CD/AUX button to
hear audio from the device over the vehicle speakers. MP3/WMA CD-R Disc
O(Power/Volume): Turn this knob clockwise or MP3 Format
counterclockwise to increase or decrease the volume of
the portable player. Additional adjustments on a portable If you burn your own MP3/WMA disc on a personal
device might be needed to get the desired volume. computer:
Make sure the MP3/WMA files are recorded on a
CD/AUX (CD/Auxiliary): Press this button once to play CD-R disc.
a CD while a portable audio device is playing. Press
this button a second time for the system to begin Do not mix standard audio and MP3/WMA files on
playing audio from the connected portable audio player. one disc.
Once in this mode, Auxinput displays. If the auxiliary Make sure each MP3/WMA file has a .m3u or.wma
jack does not detect the presence of an output jack, extension, other file extensions might not work.
the auxiliary mode does not display.
Files can be recorded with a variety of fixed or
variable bit rates. Song title, artist name, and album
are available for display by the radio when
recorded using ID3 tags version 1 and 2.
Create a folder structure that makes it easy to find
songs while driving. Organize songs by albums
using one folder for each album. Each folder
or album should contain 18 songs or less.
Make sure to finalize the disc when burning an
MP3/WMA disc, using multiple sessions. It is usually
better to burn the disc all at once.
3-54
The player is able to read and play a maximum of No Folder
50 folders, five sessions, and 999 files. Long file names
and folder names can use more disc memory space When a CD contains only compressed files, the files are
than necessary. To conserve space on the disc, located under the root folder. The next and previous
minimize the length of the file and folder names. folder function does not function on a CD that was
An MP3/WMA CD that was recorded using no file folders recorded without folders or playlists. When displaying
can also be played. The system can support up to the name of the folder the radio displays ROOT.
eight folders in depth, though, keep the depth of the When a CD contains only compressed audio files, but
folders to a minimum in order to keep down the no folders, all files are located under the root folder.
complexity and confusion in trying to locate a particular When the radio displays the name of the folder, the radio
folder during playback. If a CD contains more than displays ROOT.
the maximum of 50 folders, five sessions, and 999 files,
the player lets you access and navigate up to the Order of Play
maximum, but all items over the maximum are ignored.
Tracks are played in the following order:
Root Directory Playback begins from the first track under the root
The root directory is treated as a folder. If the root directory.
directory has compressed audio files, the directory is When all tracks from the root directory have played,
displayed as ROOT. All files contained directly under the playback continues from files, according to their
root directory are accessed prior to any other directory. numerical listing.
Empty Directory or Folder After playing the last track from the last folder, the
player begins playing again at the first track of the
If a root directory or a folder exists somewhere in the file first folder or root directory.
structure that contains only folders/subfolders and
no compressed files directly beneath them, the player
advances to the next folder in the file structure that
contains compressed audio files. The empty folder
does not display.
3-55
File System and Naming The CD player can play the smaller 3 inch (8 cm) single
CDs with an adapter ring. Full-size CDs and the
The song name in the ID3 tag is displayed. If the song smaller CDs are loaded in the same manner.
name is not present in the ID3 tag, then the radio
displays the file name without the extension (such as If playing a CD-R, the sound quality can be reduced
MP3/WMA) instead. due to CD-R quality, the method of recording, the quality
of the music that has been recorded, and the way the
Track names longer than 32 characters or four pages CD-R has been handled. There can be an increase
are shortened. Parts of words on the last page of in skipping, difficulty in finding tracks, and/or difficulty in
text and the extension of the filename does not display. loading and ejecting. If these problems occur, check
the bottom surface of the CD. If the surface of the CD is
Playing an MP3/WMA damaged, such as cracked, broken, or scratched, the
While the ignition is on, insert a CD partway into the CD does not play properly. If the surface of the CD
slot, label side up. The player pulls it in, Loading, then is soiled, see Care of Your CDs on page 3-63 for more
Filecheck, and then MP3 or WMA displays. The CD information.
should begin playing. A CD plays only while the ignition If there is no apparent damage, try a known good CD.
is in the ON/RUN or ACC/ACCESSORY.
Do not add any label to a CD, it could get caught in the
As each new track starts to play, the track number, and CD player. If a CD is recorded on a personal computer
the song name displays. and a description label is needed, try labeling the top of
If the ignition or radio is turned off with a CD in the the recorded CD with a marking pen.
player, it stays in the player. When a CD is in the player Notice: If a label is added to a CD, or more than
and the ignition is turned on, the radio must be turned one CD is inserted into the slot at a time, or an
on before the CD starts playback. When the ignition attempt is made to play scratched or damaged CDs,
and radio are turned on, the CD starts playing where it the CD player could be damaged. While using the
stopped, if it was the last selected audio source. CD player, use only CDs in good condition without
3-56
any label, load one CD at a time, and keep the CD SEEK (Previous/Next Folder) (in MP3/WMA
player and the loading slot free of foreign materials, Mode): Press the SEEK arrows to change the folder.
liquids, and debris. If CD-R does not have any folder, ROOT flashes
If an error displays, see CD Messages later in this on the display for a short time.
section.
( ) TUNE (Previous/Next Track): Press the up
All of the CD functions work the same while playing an TUNE arrow to go to the next track. The track number
MP3/WMA, except for those listed here. See Playing displays. Press the down TUNE arrow to go to the
a CD earlier for more information. start of the current track. The player continues moving
SCROLL (MP3/WMA Mode Only): Press the SOUND forward or backward through the CD with each press of
button for longer than two seconds. The song title or the TUNE arrows.
other available information of a song scrolls on/off. INFO/DISP (Information/Display): Press this button
The offset is scroll on. The scroll mode can be changed to display additional text information related to the
only when the SOUND button is pressed for longer current MP3/WMA song. A choice of additional
than two seconds. information such as: Song Title, Album Title, and Artist.
DIR (Directory): Press this button to repeat the tracks Bit rate might also display.
in the current directory. DIR displays. When information is not available, No Info (information)
Press this button again to repeat the tracks in all of the displays.
directories. ALL displays. Press this button for longer than two seconds to change
Press this button again to turn off repeat play. display mode.
3-57
Using an MP3 The player is able to read and play a maximum of
50 folders, five sessions, and 999 files. Long file names
(Radio with Six-Disc Player) and folder names might use more disc memory space
than necessary. To conserve space on the disc,
MP3/WMA CD-R Disc minimize the length of the file and folder names.
An MP3/WMA CD that was recorded using no file folders
MP3 Format can also be played. The system can support up to
If you burn your own MP3/WMA disc on a personal eight folders in depth, though, keep the depth of the
computer: folders to a minimum in order to keep down the difficulty
and confusion in trying to locate a particular folder
Make sure the MP3/WMA files are recorded on a during playback. If a CD contains more than the
CD-R disc. maximum of 50 folders, five sessions, and 999 files,
Do not mix standard audio and MP3/WMA files on the player lets you access and navigate up to the
one disc. maximum, but all items over the maximum is ignored.
Make sure each MP3/WMA file has a .m3u or.wma Root Directory
extension, other file extensions might not work.
The root directory is treated as a folder. If the root
Files can be recorded with a variety of fixed or directory has compressed audio files, the directory is
variable bit rates. Song title, artist name, and album displayed as ROOT. All files contained directly under the
are available for display by the radio when root directory are accessed prior to any other directory.
recorded using ID3 tags version 1 and 2.
Empty Directory or Folder
Create a folder structure that makes it easy to find
songs while driving. Organize songs by albums If a root directory or a folder exists somewhere in the
using one folder for each album. Each folder file structure that contains only folders/subfolders and no
or album should contain 18 songs or less. compressed files directly beneath them, the player
advances to the next folder in the file structure
Make sure to finalize the disc when burning an that contains compressed audio files. The empty folder
MP3/WMA disc, using multiple sessions. It is usually does not display.
better to burn the disc all at once.
3-58
No Folder File System and Naming
When a CD contains only compressed files, the files are The song name in the ID3 tag is displayed. If the song
located under the root folder. The next and previous name is not present in the ID3 tag, then the radio
folder function does not function on a CD that was displays the file name without the extension (such as
recorded without folders or playlists. When displaying MP3/WMA) instead.
the name of the folder the radio displays ROOT.
Track names longer than 32 characters or four pages
When a CD contains only compressed audio files, but are shortened. Parts of words on the last page of
no folders, all files are located under the root folder. text and the extension of the filename does not display.
When the radio displays the name of the folder, the radio
displays ROOT. Playing an MP3/WMA
While the ignition is on, insert a CD partway into the
Order of Play slot, label side up. The player pulls it in, Loading, then
Tracks is played in the following order: Filecheck, and then MP3 or WMA displays. The CD
should begin playing. A CD plays only while the ignition
Playback begins from the first track under the root is in the ON/RUN or ACC/ACCESSORY.
directory.
As each new track starts to play, the track number, and
When all tracks from the root directory have played, the song name displays.
playback continues from files, according to their
If the ignition or radio is turned off with a CD in the
numerical listing.
player, it stays in the player. When a CD is in the player
After playing the last track from the last folder, the and the ignition is turned on, the radio must be turned
player begins playing again at the first track of the on before the CD starts playback. When the ignition and
first folder or root directory. radio are turned on, the CD starts playing where it
stopped, if it was the last selected audio source.
3-59
The CD player can play the smaller 3 inch (8 cm) single any label, load one CD at a time, and keep the CD
CDs with an adapter ring. Full-size CDs and the player and the loading slot free of foreign materials,
smaller CDs are loaded in the same manner. liquids, and debris.
If playing a CD-R, the sound quality can be reduced If an error displays, see CD Messages later in this
due to CD-R quality, the method of recording, the quality section.
of the music that has been recorded, and the way the All of the CD functions work the same while playing an
CD-R has been handled. There can be an increase MP3/WMA, except for those listed here. See Playing
in skipping, difficulty in finding tracks, and/or difficulty in a CD earlier for more information.
loading and ejecting. If these problems occur, check
the bottom surface of the CD. If the surface of the CD is SCROLL (MP3/WMA Mode Only): Press the SOUND
damaged, such as cracked, broken, or scratched, the button for longer than two seconds. The song title
CD will not play properly. If the surface of the CD and other available information of the song scrolls on/off.
is soiled, see Care of Your CDs on page 3-63 for more The offset is scroll on. The scroll mode can be
information. changed only when the SOUND button is pressed for
If there is no apparent damage, try a known good CD. longer than two seconds.
Do not add any label to a CD, it could get caught in the 1 DIR (Directory): Press this button to repeat the
CD player. If a CD is recorded on a personal computer tracks in the current directory. DIR displays.
Press this button again to repeat the tracks in all of the
directories. ALL displays.
Notice: If a label is added to a CD, or more than
Press this button again to turn off repeat play.
one CD is inserted into the slot at a time, or an
attempt is made to play scratched or damaged CDs,
the CD player could be damaged. While using the
CD player, use only CDs in good condition without
3-60
SEEK (Previous/Next Folder) (in MP3/WMA Audio Steering Wheel Controls
Mode): Press the SEEK arrows to change the folder.
If CD-R does not have any folder, ROOT flashes
on the display for a short time.
( ) TUNE (Previous/Next Track): Press the up
TUNE arrow to go to the next track. The track number
displays. Press the down TUNE arrow to go to the
start of the current track. The player continues moving
forward or backward through the CD with each press of
the up or down arrows.
INFO/DISP (Information/Display): Press this button to
display additional text information related to the
current MP3/WMA song. A choice of additional Front View of the Side View of the
information such as: Song Title, Album Title, and Artist. Steering Wheel Controls Volume Control
Bit rate might also display.
If your vehicle has this feature, some audio controls can
When information is not available, No Info (information) be adjusted at the steering wheel. They include the
displays. following:
Press this button for longer than two seconds to change PWR (Power): Press and release this knob to turn the
display mode. system on. Press and hold this knob for more than
two seconds to turn the system off.
When the system is on, press and release this knob to
mute the system. Press and release this knob again
to turn the sound back on.
3-61
SEEK: Press and release this button within 0.5 seconds Radio Reception
to go to the next preset station.
Frequency interference and static can occur during
Press and hold this button for longer than 0.5 seconds to normal radio reception if items such as cell phone
go to the next radio station. The radio seeks stations only chargers, vehicle convenience accessories, and external
with a strong signal that are in the selected band. electronic devices are plugged into the accessory power
When playing a CD, press and release this button within outlet. If there is interference or static, unplug the item
0.5 seconds to go to the next track. Press and hold this from the accessory power outlet.
button for longer than 0.5 seconds to fast forward through
the tracks. AM
MODE: Press and release this button to select FM1, The range for most AM stations is greater than for FM,
FM2, FM-A, AM1, AM2, AM-A, or CD (MP3). Press and especially at night. The longer range can cause station
release this button multiple times to cycle through the frequencies to interfere with each other. For better radio
audio playback options that are available on your reception, most AM radio stations boost the power levels
vehicle. during the day, and then reduce these levels during the
night. Static can also occur when things like storms
+ VOLUME : Press the toggle bar located below the and power lines interfere with radio reception. When this
+ VOLUME to adjust the volume. Press the left side of happens, try reducing the treble on your radio.
the toggle bar, below the + (plus) sign to increase the
volume. Press the right side of the toggle bar, below FM Stereo
the (minus) sign to decrease the volume.
FM stereo gives the best sound, but FM signals reach
only about 10 to 40 miles (16 to 65 km). Tall buildings or
hills can interfere with FM signals, causing the sound
to fade in and out.
3-62
Care of Your CDs Integrated Windshield Antenna
Handle CDs carefully. Store them in their original cases The antenna is located in the windshield. It is a very
or other protective cases and away from direct thin metal layer that outlines near the edges of the
sunlight and dust. The CD player scans the bottom windshield. The connector is at the top of the windshield,
surface of the disc. If the surface of a CD is damaged, where the headliner ends. For proper radio reception,
such as cracked, broken, or scratched, the CD does the antenna connector at the top of the windshield needs
not play properly or not at all. If the surface of a CD is to be properly attached to the post on the glass.
soiled, take a soft, lint free cloth or dampen a clean,
If difficulty with remote transmitters is experienced,
soft cloth in a mild, neutral detergent solution mixed
such as a garage door opener, try pointing the device
with water, and clean it. Make sure the wiping process through the very top of the windshield.
starts from the center to the edge.
Do not touch the bottom side of a CD while handling it; Notice: Using a razor blade or sharp object to
this could damage the surface. Pick up CDs by clear the inside windshield may damage the
grasping the outer edges or the edge of the hole and antenna. Repairs would not be covered by your
the outer edge. warranty. Do not clear the inside windshield
with sharp objects.
Care of the CD Player Make sure the inside surface of the windshield is not
scratched and that the lines on the glass are not
Do not use CD lens cleaners for CD players because damaged. If the inside surface is damaged, it could
the lens of the CD optics can become contaminated by interfere with radio reception.
lubricants.
3-63
NOTES
3-64
Section 4 Driving Your Vehicle
Your Driving, the Road, and Your Vehicle ..........4-2 Before Leaving on a Long Trip .......................4-11
Defensive Driving ...........................................4-2 Highway Hypnosis ........................................4-12
Drunk Driving .................................................4-2 Hill and Mountain Roads ................................4-12
Control of a Vehicle ........................................4-3 Winter Driving ..............................................4-13
Braking .........................................................4-3 If Your Vehicle is Stuck in Sand, Mud,
Antilock Brake System (ABS) ...........................4-4 Ice, or Snow .............................................4-17
Braking in Emergencies ...................................4-5 Rocking Your Vehicle to Get It Out .................4-18
Steering ........................................................4-6 Loading Your Vehicle ....................................4-18
Off-Road Recovery .........................................4-8 Towing ..........................................................4-23
Passing ........................................................4-8 Towing Your Vehicle .....................................4-23
Loss of Control ..............................................4-8 Recreational Vehicle Towing ...........................4-23
Driving at Night ............................................4-10 Towing a Trailer ...........................................4-25
Driving in Rain and on Wet Roads ..................4-10
4-1
Your Driving, the Road, and Drunk Driving
Your Vehicle
{CAUTION:
Defensive Driving
Drinking and then driving is very dangerous.
Defensive driving means always expect the Your reflexes, perceptions, attentiveness, and
unexpected. The first step in driving defensively is to
judgment can be affected by even a small
wear your safety belt See Safety Belts: They Are for
Everyone on page 1-10. amount of alcohol. You can have a serious or
even fatal collision if you drive after drinking.
Do not drink and drive or ride with a driver
{CAUTION: who has been drinking. Ride home in a cab;
or if you are with a group, designate a driver
who will not drink.
Assume that other road users (pedestrians,
bicyclists, and other drivers) are going to be
careless and make mistakes. Anticipate what Death and injury associated with drinking and driving is
they might do and be ready. In addition: a global tragedy.
Allow enough following distance between Alcohol affects four things that anyone needs to drive a
you and the driver in front of you. vehicle: judgment, muscular coordination, vision, and
Focus on the task of driving. attentiveness.
Driver distraction can cause collisions Police records show that almost 40 percent of all motor
resulting in injury or possible death. These vehicle-related deaths involve alcohol. In most cases,
simple defensive driving techniques could these deaths are the result of someone who was
save your life. drinking and driving. In recent years, more than
17,000 annual motor vehicle-related deaths have been
associated with the use of alcohol, with about
250,000 people injured.
4-2
For persons under 21, it is against the law in every Braking
U.S. state to drink alcohol. There are good medical,
psychological, and developmental reasons for See Brake System Warning Light on page 3-31.
these laws.
Braking action involves perception time and reaction
The obvious way to eliminate the leading highway time. First, you have to decide to push on the brake
safety problem is for people never to drink alcohol and pedal. That is perception time. Then you have to bring
then drive. up your foot and do it. That is reaction time.
Medical research shows that alcohol in a persons Average reaction time is about three-fourths of a
system can make crash injuries worse, especially second. But that is only an average. It might be less
injuries to the brain, spinal cord, or heart. This means with one driver and as long as two or three seconds or
that when anyone who has been drinking driver more with another. Age, physical condition, alertness,
or passenger is in a crash, that persons chance of coordination, and eyesight all play a part. So do alcohol,
being killed or permanently disabled is higher than if the drugs, and frustration. But even in three-fourths of a
person had not been drinking. second, a vehicle moving at 60 mph (100 km/h) travels
66 feet (20 m). That could be a lot of distance in an
Control of a Vehicle emergency, so keeping enough space between
your vehicle and others is important.
The following three systems help to control your vehicle And, of course, actual stopping distances vary greatly
while driving brakes, steering, and accelerator. with the surface of the road, whether it is pavement
At times, as when driving on snow or ice, it is easy to ask or gravel; the condition of the road, whether it is wet,
more of those control systems than the tires and road can dry, or icy; tire tread; the condition of the brakes;
provide. Meaning, you can lose control of your vehicle. the weight of the vehicle; and the amount of brake
Adding non-dealer/non-retailer accessories can affect force applied.
your vehicles performance. See Accessories and
Modifications on page 5-4.
4-3
Avoid needless heavy braking. Some people drive Antilock Brake System (ABS)
in spurts heavy acceleration followed by heavy
braking rather than keeping pace with traffic. Your vehicle might have the Antilock Brake System
This is a mistake. The brakes might not have time to (ABS), an advanced electronic braking system that will
cool between hard stops. The brakes will wear out help prevent a braking skid.
much faster if you do a lot of heavy braking. If you
keep pace with the traffic and allow realistic following If your vehicle has ABS,
distances, you will eliminate a lot of unnecessary this warning light on the
braking. That means better braking and longer instrument panel will come
brake life. on briefly when you
start your vehicle.
If your vehicles engine ever stops while you are driving,
brake normally but do not pump the brakes. If you do,
the pedal could get harder to push down. If the
engine stops, you will still have some power brake
assist. But you will use it when you brake. Once the Let us say the road is wet and you are driving safely.
power assist is used up, it can take longer to stop and Suddenly, an animal jumps out in front of you. You slam
the brake pedal will be harder to push. on the brakes and continue braking. Here is what
Adding non-dealer/non-retailer accessories can affect happens with ABS:
your vehicles performance. See Accessories and A computer senses that wheels are slowing down.
Modifications on page 5-4. If one of the wheels is about to stop rolling, the computer
will separately work the brakes at each wheel.
4-4
ABS can change the brake pressure faster than any Braking in Emergencies
driver could. The computer is programmed to make the
most of available tire and road conditions. This can At some time, nearly every driver gets into a situation
help you steer around the obstacle while braking hard. that requires hard braking.
As you brake, the computer keeps receiving updates If you have ABS, you can steer and brake at the same
on wheel speed and controls braking pressure time. However, if you do not have ABS, your first
accordingly. reaction to hit the brake pedal hard and hold it
Remember: ABS does not change the time you need to down might be the wrong thing to do. Your wheels
get your foot up to the brake pedal or always decrease can stop rolling. Once they do, the vehicle cannot
stopping distance. If you get too close to the vehicle respond to your steering. Momentum will carry it in
in front of you, you will not have time to apply the brakes whatever direction it was headed when the wheels
if that vehicle suddenly slows or stops. Always leave stopped rolling. That could be off the road, into the
enough room up ahead to stop, even though you very thing you were trying to avoid, or into traffic.
have ABS. If you do not have ABS, use a squeeze braking
technique. This will give you maximum braking while
Using ABS maintaining steering control. You can do this by pushing
Do not pump the brakes. Just hold the brake pedal on the brake pedal with steadily increasing pressure.
down firmly and let antilock work for you. You might feel In an emergency, you will probably want to squeeze the
a slight brake pedal pulsation or notice some noise, brakes hard without locking the wheels. If you hear or
but this is normal. feel the wheels sliding, ease off the brake pedal.
This will help you retain steering control. If you do have
ABS, it is different. See Antilock Brake System (ABS)
on page 4-4.
In many emergencies, steering can help you more than
even the very best braking.
4-5
Steering The traction you can get in a curve depends on the
condition of the tires and the road surface, the angle
Power Steering at which the curve is banked, and your speed.
While you are in a curve, speed is the one factor you
If you lose power steering assist because the engine can control.
stops or the system is not functioning, you can steer but
it will take much more effort. Suppose you are steering through a sharp curve.
Then you suddenly apply the brakes. Both control
Speed Sensitive Power Steering (SSPS) systems steering and braking have to do their
work where the tires meet the road. Unless you have
If your vehicle has this optional steering system, the antilock brakes, adding the hard braking can demand too
steering system continuously adjusts the effort you feel much of those places. You can lose control.
when steering at all vehicle speeds. It provides ease
when parking, yet a firm, solid feel at highway speeds. The same thing can happen if you are steering through
a sharp curve and you suddenly accelerate. Those
Steering Tips two control systems steering and acceleration can
overwhelm those places where the tires meet the road
It is important to take curves at a reasonable speed.
and make you lose control.
A lot of the driver lost control accidents mentioned on
What should you do if this ever happens? Ease up on
the news happen on curves.
the brake or accelerator pedal, steer the vehicle the way
Here is why: you want it to go, and slow down.
Experienced driver or beginner, each of us is subject to Speed limit signs near curves warn that you should
the same laws of physics when driving on curves. adjust your speed. Of course, the posted speeds
The traction of the tires against the road surface makes are based on good weather and road conditions. Under
it possible for the vehicle to change its path when you less favorable conditions you will want to go slower.
turn the front wheels. If there is no traction, inertia
If you need to reduce your speed as you approach
will keep the vehicle going in the same direction. If you
a curve, do it before you enter the curve, while the
have ever tried to steer a vehicle on wet ice, you will
front wheels are straight ahead.
understand this.
4-6
Try to adjust your speed so you can drive through the
curve. Maintain a reasonable, steady speed. Wait
to accelerate until you are out of the curve, and then
accelerate gently into the straightaway.
Adding non-dealer/non-retailer accessories can affect
your vehicles performance. See Accessories and
Modifications on page 5-4.
Steering in Emergencies
There are times when steering can be more effective
than braking. For example, you come over a hill and find
a truck stopped in your lane, or a car suddenly pulls
out from nowhere, or a child darts out from between
parked cars and stops right in front of you. You can
avoid these problems by braking if you can stop in
An emergency like this requires close attention and a
time. But sometimes you cannot; there is not room.
quick decision. If you are holding the steering wheel at
That is the time for evasive action steering around
the recommended 9 and 3 oclock positions, you can
the problem.
turn it a full 180 degrees very quickly without removing
Your vehicle can perform very well in emergencies like either hand. But you have to act fast, steer quickly,
these. First apply the brakes but, unless you have and just as quickly straighten the wheel once you have
antilock brakes, not enough to lock the wheels. avoided the object.
See Braking on page 4-3. It is better to remove as much
The fact that such emergency situations are always
speed as you can from a possible collision. Then steer
possible is a good reason to practice defensive driving
around the problem, to the left or right depending on the
at all times and wear safety belts properly.
space available.
4-7
Off-Road Recovery Passing
You may find that your vehicles right wheels have Passing another vehicle on a two-lane road can be
dropped off the edge of a road onto the shoulder while dangerous. To reduce the risk of danger while passing,
you are driving. we suggest the following tips:
Look down the road, to the sides, and to crossroads
for situations that might affect a successful pass.
If in doubt, wait.
Watch for traffic signs, pavement markings, and
lines that could indicate a turn or an intersection.
Never cross a solid or double-solid line on your side
of the lane.
Do not get too close to the vehicle you want to
pass. Doing so can reduce your visibility.
Wait your turn to pass a slow vehicle.
When you are being passed, ease to the right.
Loss of Control
If the level of the shoulder is only slightly below the Let us review what driving experts say about what
pavement, recovery should be fairly easy. Ease off the happens when the three control systems brakes,
accelerator and then, if there is nothing in the way, steering, and acceleration do not have enough friction
steer so that your vehicle straddles the edge of the where the tires meet the road to do what the driver has
pavement. You can turn the steering wheel up to asked.
one-quarter turn until the right front tire contacts the In any emergency, do not give up. Keep trying to
pavement edge. Then turn the steering wheel to steer and constantly seek an escape route or area of
go straight down the roadway. less danger.
4-8
Skidding While driving on a surface with reduced traction,
try your best to avoid sudden steering, acceleration, or
In a skid, a driver can lose control of the vehicle. braking, including reducing vehicle speed by shifting
Defensive drivers avoid most skids by taking reasonable to a lower gear. Any sudden changes could cause
care suited to existing conditions, and by not overdriving the tires to slide. You may not realize the surface is
those conditions. But skids are always possible. slippery until your vehicle is skidding. Learn to
The three types of skids correspond to your vehicles recognize warning clues such as enough water, ice,
three control systems. In the braking skid, the wheels are or packed snow on the road to make a mirrored
not rolling. In the steering or cornering skid, too much surface and slow down when you have any doubt.
speed or steering in a curve causes tires to slip and lose If you have the Antilock Brake System (ABS),
cornering force. And in the acceleration skid, too much remember: It helps avoid only the braking skid. If you
throttle causes the driving wheels to spin. do not have ABS, then in a braking skid, where the
A cornering skid and an acceleration skid are best wheels are no longer rolling, release enough pressure
handled by easing your foot off the accelerator pedal. on the brakes to get the wheels rolling again. This
restores steering control. Push the brake pedal down
If your vehicle starts to slide, ease your foot off the steadily when you have to stop suddenly. As long as the
accelerator pedal and quickly steer the way you want wheels are rolling, you will have steering control.
the vehicle to go. If you start steering quickly enough,
your vehicle may straighten out. Always be ready
for a second skid if it occurs.
Of course, traction is reduced when water, snow, ice,
gravel, or other material is on the road. For safety, you
will want to slow down and adjust your driving to
these conditions. It is important to slow down on slippery
surfaces because stopping distance will be longer and
vehicle control more limited.
4-9
Driving at Night Driving in Rain and on Wet Roads
Night driving is more dangerous than day driving because Rain and wet roads can reduce vehicle traction and
some drivers are likely to be impaired by alcohol or affect your ability to stop and accelerate. Always drive
drugs, with night vision problems, or by fatigue. slower in these types of driving conditions and avoid
Night driving tips include: driving through large puddles and deep-standing
or flowing water.
Drive defensively.
Do not drink and drive.
Reduce headlamp glare by adjusting the inside {CAUTION:
rearview mirror.
Slow down and keep more space between you and Wet brakes can cause crashes. They might not
other vehicles because your headlamps can only work as well in a quick stop and could cause
light up so much road ahead. pulling to one side. You could lose control of
Watch for animals. the vehicle.
When tired, pull off the road. After driving through a large puddle of water
or a car/vehicle wash, lightly apply the brake
Do not wear sunglasses.
pedal until the brakes work normally.
Avoid staring directly into approaching headlamps.
Flowing or rushing water creates strong
Keep the windshield and all glass on your vehicle forces. Driving through flowing water could
clean inside and out. cause your vehicle to be carried away. If this
Keep your eyes moving, especially during turns happens, you and other vehicle occupants
or curves. could drown. Do not ignore police warnings
No one can see as well at night as in the daytime. and be very cautious about trying to drive
But, as we get older, these differences increase. through flowing water.
A 50-year-old driver might need at least twice as much
light to see the same thing at night as a 20-year-old.
4-10
Hydroplaning Before Leaving on a Long Trip
Hydroplaning is dangerous. Water can build up under To prepare your vehicle for a long trip, consider having
your vehicles tires so they actually ride on the it serviced by your dealer/retailer before departing.
water. This can happen if the road is wet enough and Things to check on your own include:
you are going fast enough. When your vehicle is
hydroplaning, it has little or no contact with the road. Windshield Washer Fluid: Reservoir full?
Windows clean inside and outside?
There is no hard and fast rule about hydroplaning.
The best advice is to slow down when the road is wet. Wiper Blades: In good shape?
Fuel, Engine Oil, Other Fluids: All levels checked?
Other Rainy Weather Tips Lamps: Do they all work and are lenses clean?
Besides slowing down, other wet weather driving tips Tires: Are treads good? Are tires inflated to
include: recommended pressure?
Allow extra following distance. Weather and Maps: Safe to travel?
Pass with caution. Have up-to-date maps?
Keep windshield wiping equipment in good shape.
Keep the windshield washer fluid reservoir filled.
Have good tires with proper tread depth. See Tires
on page 5-49.
4-11
Highway Hypnosis Hill and Mountain Roads
Always be alert and pay attention to your surroundings Driving on steep hills or through mountains is different
while driving. If you become tired or sleepy, find a than driving on flat or rolling terrain. Tips for driving
safe place to park your vehicle and rest. in these conditions include:
Other driving tips include: Keep your vehicle serviced and in good shape.
Keep the vehicle well ventilated. Check all fluid levels and brakes, tires, cooling
Keep interior temperature cool. system, and transmission.
Keep your eyes moving scan the road ahead Going down steep or long hills, shift to a
lower gear.
and to the sides.
Check the rearview mirror and vehicle
instruments often. {CAUTION:
If you do not shift down, the brakes could get
so hot that they would not work well. You
would then have poor braking or even none
going down a hill. You could crash. Shift down
to let the engine assist the brakes on a steep
downhill slope.
4-12
Winter Driving
{CAUTION: Here are some tips for winter driving:
Have your vehicle in good shape for winter.
Coasting downhill in NEUTRAL (N) or with the
You might want to put winter emergency supplies
ignition off is dangerous. The brakes will have
in your trunk.
to do all the work of slowing down and they
could get so hot that they would not work well. Include an ice scraper, a small brush or broom, a
You would then have poor braking or even supply of windshield washer fluid, a rag, some winter
outer clothing, a small shovel, a flashlight, a red
none going down a hill. You could crash.
cloth, and a couple of reflective warning triangles.
Always have the engine running and your And, if you will be driving under severe conditions,
vehicle in gear when you go downhill. include a small bag of sand, a piece of old carpet,
or a couple of burlap bags to help provide traction.
Stay in your own lane. Do not swing wide or cut Be sure you properly secure these items in your vehicle.
across the center of the road. Drive at speeds Also see Tires on page 5-49.
that let you stay in your own lane.
Top of hills: Be alert something could be in your
lane (stalled car, accident).
Pay attention to special road signs (falling rocks
area, winding roads, long grades, passing or
no-passing zones) and take appropriate action.
4-13
Driving on Snow or Ice What is the worst time for this? Wet ice. Very cold snow
or ice can be slick and hard to drive on. But wet ice
Most of the time, those places where the tires meet the can be even more trouble because it can offer the least
road probably have good traction. traction of all. You can get wet ice when it is about
However, if there is snow or ice between the tires and freezing, 32F (0C), and freezing rain begins to fall.
the road, you can have a very slippery situation. Try to avoid driving on wet ice until salt and sand crews
You have a lot less traction, or grip, and need to be can get there.
very careful. Whatever the condition smooth ice, packed, blowing,
or loose snow drive with caution.
Accelerate gently. Try not to break the fragile traction.
If you accelerate too fast, the drive wheels will spin and
polish the surface under the tires even more.
Unless your vehicle has the Antilock Brake System
(ABS), you want to brake very gently, too. If you do have
ABS, see Antilock Brake System (ABS) on page 4-4.
ABS improves your vehicles stability when you make a
hard stop on a slippery road. Whether your vehicle has
ABS or not, begin stopping sooner than you would on dry
pavement. Without ABS, if you feel your vehicle begin to
slide, let up on the brakes a little. Push the brake pedal
down steadily to get the most traction you can.
4-14
Remember, unless your vehicle has ABS, if you brake If You Are Caught in a Blizzard
so hard that the wheels stop rolling, you will just slide.
Brake so the wheels always keep rolling and you If you are stopped by heavy snow, you could be in a
can still steer. serious situation. You should probably stay with
your vehicle unless you know for sure that you are near
Whatever your vehicles braking system, allow help and you can hike through the snow. Here are
greater following distance on any slippery road. some things to do to summon help and keep yourself
Watch for slippery spots. The road might be fine and your passengers safe:
until you hit a spot that is covered with ice. Turn on the hazard warning flashers.
On an otherwise clear road, ice patches can appear
in shaded areas where the sun cannot reach, Tie a red cloth to your vehicle to alert police that
such as around clumps of trees, behind buildings, you have been stopped by the snow.
or under bridges. Sometimes the surface of a curve Put on extra clothing or wrap a blanket around you.
or an overpass can remain icy when the surrounding If you do not have blankets or extra clothing, make
roads are clear. If you see a patch of ice ahead body insulators from newspapers, burlap bags,
of you, brake before you are on it. Try not to brake rags, floor mats anything you can wrap around
while you are actually on the ice, and avoid yourself or tuck under your clothing to keep warm.
sudden steering maneuvers.
4-15
{CAUTION:
Snow can trap exhaust gases under your
vehicle. This can cause deadly CO (carbon
monoxide) gas to get inside. CO could
overcome you and kill you. You cannot see it
or smell it, so you might not know it is in your
vehicle. Clear away snow from around the
base of your vehicle, especially any that is
blocking the exhaust pipe. And check around
again from time to time to be sure snow does
not collect there.
Open a window just a little on the side of the
vehicle that is away from the wind. This will
help keep CO out.
You can run the engine to keep warm, but be careful.
4-16
Run your engine only as long as you must. This saves If Your Vehicle is Stuck in Sand,
fuel. When you run the engine, make it go a little faster
than just idle. That is, push the accelerator slightly. Mud, Ice, or Snow
This uses less fuel for the heat that you get and it keeps
Slowly and cautiously spin the wheels to free your
the battery charged. You will need a well-charged battery vehicle when stuck in sand, mud, ice, or snow. See
to restart the vehicle, and possibly for signaling later on Rocking Your Vehicle to Get It Out on page 4-18.
with the headlamps. Let the heater run for a while.
Then, shut the engine off and close the window almost all
the way to preserve the heat. Start the engine again and {CAUTION:
repeat this only when you feel really uncomfortable from
the cold. But do it as little as possible. Preserve the fuel
If you let your vehicles tires spin at high
as long as you can. To help keep warm, you can get out
speed, they can explode, and you or others
of the vehicle and do some fairly vigorous exercises
every half hour or so until help comes. could be injured. The vehicle can overheat,
causing an engine compartment fire or other
damage. Spin the wheels as little as possible
and avoid going above 35 mph (55 km/h) as
shown on the speedometer.
For information about using tire chains on your vehicle,

see Tire Chains on page 5-67.
4-17
Rocking Your Vehicle to Get It Out Loading Your Vehicle
First, turn the steering wheel left and right to clear It is very important to know how much weight your
the area around the front wheels. Then shift back and vehicle can carry. This weight is called the Maximum
forth between REVERSE (R) and a forward gear, Load weight and includes the weight of all occupants,
or with a manual transmission, between FIRST (1) or cargo, and all nonfactory-installed options. Two labels on
SECOND (2) and REVERSE (R), spinning the wheels as your vehicle show how much weight it may properly
little as possible. To prevent transmission wear, wait carry; the Tire and Loading Information label and
until the wheels stop spinning before shifting gears. the Certification label.
Release the accelerator pedal while you shift, and press
lightly on the accelerator pedal when the transmission
is in gear. By slowly spinning the wheels in the
forward and reverse directions, you will cause a rocking
{CAUTION:
motion that could free your vehicle. If that does not
get your vehicle out after a few tries, it might need to be Do not load your vehicle any heavier than
towed out. If your vehicle does need to be towed out, the Gross Vehicle Weight Rating (GVWR),
see Towing Your Vehicle on page 4-23. or either the maximum front or rear Gross
Axle Weight Rating (GAWR). If you do,
parts on your vehicle can break, and it
can change the way your vehicle handles.
These could cause you to lose control
and crash. Also, overloading can shorten
the life of your vehicle.
4-18
Tire and Loading Information Label
Label Example Wagon
A vehicle specific Tire and Loading Information label

shows the seating capacity and the maximum load your
vehicle can properly carry. This label also contains
your vehicles original equipment tire size and the
recommended tire inflation pressure. For more
information on tires and inflation see Tires on
page 5-49 and Inflation - Tire Pressure on page 5-56.
The Tire and Loading Information label is attached
inside the glove box of the five door hatchback model.
The Tire and Loading Information label for the wagon
Label Example 5 Door Hatchback is attached to the vehicles center pillar, below the
drivers door latch.
There is also important loading information on the
Certification label. It tells you the Gross Vehicle Weight
Rating (GVWR) and the Gross Axle Weight Rating
(GAWR) for the front and rear axle; see Certification
Label later in this section.
4-19
Steps for Determining Correct Load Limit
1. Locate the Maximum Load amount printed on
the Tire and Loading Information label.
2. Determine the combined weight of the driver and
passengers that will be riding in your vehicle.
3. Subtract the combined weight of the driver and
passengers from the maximum load amount,
shown in pounds and kilograms.
4. The resulting figure equals the available amount of
cargo and luggage load capacity. For example, if
the maximum load amount equals 1400 lbs and Example 1
there will be five 150 lb passengers in your vehicle,
the amount of available cargo and luggage load
capacity is 650 lbs (1400 750 (5 x 150) = 650 lbs). Item Description Total
A Vehicle Maximum Load 1,000 lbs (453 kg)
5. Determine the combined weight of luggage and for Example 1 =
cargo being loaded on the vehicle. That weight
Subtract Occupant
may not safely exceed the available cargo B Weight 150 lbs 300 lbs (136 kg)
and luggage load capacity calculated in Step 4. (68 kg) 2 =
C Available Occupant and 700 lbs (317 kg)
Cargo Weight =
4-20
Example 2 Example 3
Item Description Total Item Description Total

A Vehicle Maximum Load 1,000 lbs (453 kg) A Vehicle Maximum Load 1,000 lbs (453 kg)
for Example 2 = for Example 3 =
Subtract Occupant Subtract Occupant
B Weight 150 lbs 750 lbs (340 kg) B Weight 200 lbs 1,000 lbs (453 kg)
(68 kg) 5 = (91 kg) 5 =
C Available Cargo Weight = 250 lbs (113 kg) C Available Cargo Weight = 0 lbs (0 kg)
Refer to your vehicles Tire and Loading Information

label for specific information about your vehicles
maximum load weight and seating positions.
The combined weight of the driver, passengers, and
cargo should never exceed your vehicles maximum
load weight.
4-21
Certification Label And, if you do have a heavy load, you should spread it
out. See Steps for Determining Correct Load Limit
earlier in this section.
{CAUTION:
Do not load your vehicle any heavier than
the Gross Vehicle Weight Rating (GVWR),
or either the maximum front or rear Gross
Axle Weight Rating (GAWR). If you do,
parts on your vehicle can break, and it
Label Example can change the way your vehicle handles.
These could cause you to lose control
A vehicle specific Certification label is attached to the and crash. Also, overloading can shorten
center pillar, near the drivers door latch. This label tells the life of your vehicle.
you the gross weight capacity of your vehicle, called
the Gross Vehicle Weight Rating (GVWR). The GVWR
includes the weight of the vehicle, all occupants, fuel, Notice: Overloading your vehicle may cause
and cargo. Never exceed the GVWR for your vehicle, or damage. Repairs would not be covered by your
the Gross Axle Weight Rating (GAWR) for either the warranty. Do not overload your vehicle.
front or rear axle.
4-22
If you put things inside your vehicle like suitcases,
tools, packages, or anything else they will go as fast
Towing
as the vehicle goes. If you have to stop or turn
quickly, or if there is a crash, they will keep going. Towing Your Vehicle
Consult your dealer/retailer or a professional towing
{CAUTION: service if you need to have your disabled vehicle towed.
See Roadside Assistance Program on page 7-6.
If you want to tow your vehicle behind another vehicle
Things you put inside your vehicle can
for recreational purposes (such as behind a motorhome),
strike and injure people in a sudden stop
see Recreational Vehicle Towing following.
or turn, or in a crash.
Put things in the trunk of your vehicle.
In a trunk, put them as far forward as Recreational Vehicle Towing
you can. Try to spread the weight Recreational vehicle towing means towing your vehicle
evenly. behind another vehicle, such as behind a motorhome.
Never stack heavier things, like The two most common types of recreational vehicle
suitcases, inside the vehicle so that towing are known as dinghy towing (towing your vehicle
some of them are above the tops of with all four wheels on the ground) and dolly towing
the seats. (towing your vehicle with two wheels on the ground and
Do not leave an unsecured child two wheels up on a device known as a dolly).
restraint in your vehicle.
When you carry something inside the
vehicle, secure it whenever you can.
Do not leave a seat folded down
unless you need to.
4-23
With the proper preparation and equipment, many Dinghy Towing
vehicles can be towed in these ways. See Dinghy
Towing and Dolly Towing, following. Notice: If you tow your vehicle with all four wheels
Here are some important things to consider before you on the ground, the drivetrain components could
do recreational vehicle towing: be damaged. The repairs would not be covered by
your warranty. Do not tow your vehicle with all
What is the towing capacity of the towing vehicle? four wheels on the ground.
Be sure you read the tow vehicle manufacturers
Your vehicle was not designed to be towed with all four
recommendations.
wheels on the ground. If your vehicle must be towed,
How far will you tow? Some vehicles have you should use a dolly. See Dolly Towing that follows
restrictions on how far and how long they can tow. for more information.
Do you have the proper towing equipment?
See your dealer/retailer or trailering professional for
additional advice and equipment recommendations.
Is your vehicle ready to be towed? Just as you
would prepare your vehicle for a long trip, you
will want to make sure your vehicle is prepared to
be towed. See Before Leaving on a Long Trip
on page 4-11.
4-24
Dolly Towing 4. Set the parking brake and then remove the key.
Notice: Towing your vehicle from the rear with 5. Clamp the steering wheel in a straight-ahead
the front wheels on the ground could cause position.
transmission damage. Do not tow the vehicle 6. Release the parking brake.
from the rear with the front wheels on the road.
Towing a Trailer
Do not use your vehicle to tow a trailer. The vehicle
is not designed or intended for such a use. Towing a
trailer can adversely affect handling, durability and
fuel economy.
Your vehicle can be towed using a dolly. To tow your

vehicle using a dolly, follow these steps:
1. Put the front wheels on a dolly.
2. Turn the ignition to ACC/ACCESSORY.
3. Put the vehicle in NEUTRAL (N).
4-25
NOTES
4-26
Section 5 Service and Appearance Care
Service ............................................................5-4 Engine Coolant .............................................5-19
Accessories and Modifications ..........................5-4 Coolant Surge Tank Pressure Cap ..................5-22
California Proposition 65 Warning .....................5-4 Engine Overheating .......................................5-22
California Perchlorate Materials Requirements .....5-5 Cooling System ............................................5-24
Doing Your Own Service Work .........................5-5 Power Steering Fluid .....................................5-29
Adding Equipment to the Outside of Windshield Washer Fluid ................................5-30
Your Vehicle ..............................................5-5 Brakes ........................................................5-31
Fuel ................................................................5-6 Battery ........................................................5-34
Gasoline Octane ............................................5-6 Jump Starting ...............................................5-35
Gasoline Specifications ....................................5-6 Headlamp Aiming ...........................................5-40
California Fuel ...............................................5-6 Bulb Replacement ..........................................5-40
Additives .......................................................5-6 Halogen Bulbs ..............................................5-40
Fuels in Foreign Countries ...............................5-7 Headlamps ..................................................5-41
Filling the Tank ..............................................5-8 Front Turn Signal and Parking Lamps ..............5-42
Filling a Portable Fuel Container .....................5-10 Turn Signal Lamps (Side) ..............................5-43
Checking Things Under the Hood ....................5-10 Sidemarker Lamps (Front) ..............................5-44
Hood Release ..............................................5-11 Sidemarker Lamps (Rear) ..............................5-44
Engine Compartment Overview .......................5-12 Center High-Mounted Stoplamp (CHMSL)
Engine Oil ...................................................5-13 (Hatchback) ..............................................5-45
Engine Air Cleaner/Filter ................................5-16 Center High-Mounted Stoplamp (CHMSL)
Automatic Transmission Fluid .........................5-18 (Wagon) ...................................................5-45
Manual Transmission Fluid .............................5-18 Taillamps, Turn Signal, and Stoplamps
Hydraulic Clutch ...........................................5-18 (Hatchback) ..............................................5-46
5-1
Taillamps, Turn Signal, Stoplamps and Removing the Flat Tire and Installing the
Back-up Lamps (Wagon) ............................5-46 Spare Tire ................................................5-73
Taillamps, Stoplamps and Back-up Lamps Storing a Flat or Spare Tire and Tools ............5-78
(Hatchback) ..............................................5-47 Compact Spare Tire ......................................5-78
License Plate Lamp ......................................5-47 Appearance Care ............................................5-79
Replacement Bulbs .......................................5-48 Interior Cleaning ...........................................5-79
Windshield Wiper Blade Replacement ..............5-48 Fabric/Carpet ...............................................5-80
Tires ..............................................................5-49 Leather .......................................................5-81
Tire Sidewall Labeling ...................................5-50 Instrument Panel, Vinyl, and Other Plastic
Tire Terminology and Definitions .....................5-53 Surfaces ..................................................5-81
Inflation - Tire Pressure .................................5-56 Care of Safety Belts ......................................5-81
Tire Pressure Monitor System .........................5-57 Weatherstrips ...............................................5-82
Tire Pressure Monitor Operation .....................5-59 Washing Your Vehicle ...................................5-82
Tire Inspection and Rotation ...........................5-60 Cleaning Exterior Lamps/Lenses .....................5-82
When It Is Time for New Tires .......................5-62 Finish Care ..................................................5-82
Buying New Tires .........................................5-62 Windshield and Wiper Blades .........................5-83
Different Size Tires and Wheels ......................5-64 Aluminum Wheels .........................................5-84
Uniform Tire Quality Grading ..........................5-64 Tires ...........................................................5-84
Wheel Alignment and Tire Balance ..................5-66 Sheet Metal Damage .....................................5-84
Wheel Replacement ......................................5-66 Finish Damage .............................................5-85
Tire Chains ..................................................5-67 Underbody Maintenance ................................5-85
If a Tire Goes Flat ........................................5-68 Chemical Paint Spotting .................................5-85
Changing a Flat Tire .....................................5-69 Vehicle Care/Appearance Materials ..................5-86
Removing the Spare Tire and Tools ................5-70
5-2
Vehicle Identification ......................................5-87 Power Windows and Other Power Options .......5-88
Vehicle Identification Number (VIN) .................5-87 Fuses and Circuit Breakers ............................5-89
Service Parts Identification Label .....................5-87 Instrument Panel Fuse Block ..........................5-89
Electrical System ............................................5-88 Engine Compartment Fuse Block ....................5-91
Add-On Electrical Equipment ..........................5-88 Capacities and Specifications ..........................5-94
Headlamp Wiring ..........................................5-88 Maintenance Replacement Parts ......................5-95
Windshield Wiper Fuses ................................5-88 Engine Drive Belt Routing ..............................5-96
5-3
Service Accessories and Modifications
For service and parts needs, visit your dealer/retailer. When non-dealer/non-retailer accessories are added to
You will receive genuine GM parts and GM-trained and your vehicle they can affect your vehicles performance
supported service people. and safety, including such things as, airbags, braking,
stability, ride and handling, emissions systems,
Genuine GM parts have one of these marks: aerodynamics, durability, and electronic systems like
antilock brakes, traction control and stability control.
Some of these accessories could even cause
malfunction or damage not covered by warranty.
GM Accessories are designed to complement and
function with other systems on your vehicle. Your GM
dealer/retailer can accessorize your vehicle using
genuine GM Accessories. When you go to your GM
dealer/retailer and ask for GM Accessories, you will know
that GM-trained and supported service technicians will
perform the work using genuine GM Accessories.
Also, see Adding Equipment to Your Airbag-Equipped
Vehicle on page 1-64.
California Proposition 65 Warning

Most motor vehicles, including this one, contain and/or
emit chemicals known to the State of California to
cause cancer and birth defects or other reproductive
harm. Engine exhaust, many parts and systems
(including some inside the vehicle), many fluids, and
some component wear by-products contain and/or emit
these chemicals.
5-4
California Perchlorate Materials If you want to do some of your own service work, you
will want to use the proper service manual. It tells
Requirements you much more about how to service your vehicle than
this manual can. To order the proper service manual,
Certain types of automotive applications, such as airbag
see Service Publications Ordering Information on
initiators, seat belt pretensioners, and lithium batteries
page 7-15.
contained in remote keyless entry transmitters, may
contain perchlorate materials. Special handling Your vehicle has an airbag system. Before attempting
may be necessary. For additional information, to do your own service work, see Servicing Your
see www.dtsc.ca.gov/hazardouswaste/perchlorate. Airbag-Equipped Vehicle on page 1-64.
You should keep a record with all parts receipts and list
Doing Your Own Service Work the mileage and the date of any service work you
perform. See Part E: Maintenance Record on page 6-28.
{CAUTION: Adding Equipment to the Outside

You can be injured and your vehicle could be
of Your Vehicle
damaged if you try to do service work on a Things you might add to the outside of your vehicle can
vehicle without knowing enough about it. affect the airflow around it. This can cause wind
Be sure you have sufficient knowledge, noise and can affect fuel economy and windshield
experience, the proper replacement parts, washer performance. Check with your dealer/retailer
and tools before you attempt any vehicle before adding equipment to the outside of your vehicle.
maintenance task.
Be sure to use the proper nuts, bolts, and
other fasteners. English and metric
fasteners can be easily confused. If you
use the wrong fasteners, parts can later
break or fall off. You could be hurt.
5-5
Fuel California Fuel
Use of the recommended fuel is an important part of If your vehicle is certified to meet California Emissions
the proper maintenance of your vehicle. To help Standards, it is designed to operate on fuels that
keep the engine clean and maintain optimum vehicle meet California specifications. See the underhood
performance, we recommend the use of gasoline emission control label. If this fuel is not available
advertised as TOP TIER Detergent Gasoline. in states adopting California emissions standards, your
vehicle will operate satisfactorily on fuels meeting
federal specifications, but emission control system
Gasoline Octane performance might be affected. The malfunction
Use regular unleaded gasoline with a posted octane indicator lamp could turn on and your vehicle might fail
rating of 87 or higher. If the octane rating is less than 87, a smog-check test. See Malfunction Indicator Lamp
you might notice an audible knocking noise when you on page 3-34. If this occurs, return to your authorized
drive, commonly referred to as spark knock. If this dealer/retailer for diagnosis. If it is determined that
occurs, use a gasoline rated at 87 octane or higher as the condition is caused by the type of fuel used, repairs
soon as possible. If you are using gasoline rated at might not be covered by your warranty.
87 octane or higher and you hear heavy knocking,
the engine needs service. Additives
To provide cleaner air, all gasolines in the United States
Gasoline Specifications are now required to contain additives that help prevent
At a minimum, gasoline should meet ASTM engine and fuel system deposits from forming, allowing
specification D 4814 in the United States or the emission control system to work properly. In most
CAN/CGSB-3.5 or 3.511 in Canada. Some gasolines cases, you should not have to add anything to the fuel.
contain an octane-enhancing additive called
methylcyclopentadienyl manganese tricarbonyl (MMT).
We recommend against the use of gasolines
containing MMT. See Additives on page 5-6 for
additional information.
5-6
However, some gasolines contain only the minimum Some gasolines that are not reformulated for low
amount of additive required to meet U.S. Environmental emissions can contain an octane-enhancing additive
Protection Agency regulations. To help keep fuel called methylcyclopentadienyl manganese tricarbonyl
injectors and intake valves clean, or if your vehicle (MMT); ask the attendant where you buy gasoline
experiences problems due to dirty injectors or valves, whether the fuel contains MMT. We recommend against
look for gasoline that is advertised as TOP TIER the use of such gasolines. Fuels containing MMT can
Detergent Gasoline. Also, your dealer/retailer has reduce the life of spark plugs and the performance
additives that will help correct and prevent most of the emission control system could be affected.
deposit-related problems. The malfunction indicator lamp might turn on. If this
occurs, return to your dealer/retailer for service.
Gasolines containing oxygenates, such as ethers and
ethanol, and reformulated gasolines might be available
in your area. We recommend that you use these Fuels in Foreign Countries
gasolines, if they comply with the specifications
described earlier. However, E85 (85% ethanol) and If you plan on driving in another country outside the
other fuels containing more than 10% ethanol must United States or Canada, the proper fuel might be hard
not be used in vehicles that were not designed for to find. Never use leaded gasoline or any other fuel
those fuels. not recommended in the previous text on fuel. Costly
repairs caused by use of improper fuel would not
Notice: Your vehicle was not designed for fuel that be covered by your warranty.
contains methanol. Do not use fuel containing
methanol. It can corrode metal parts in the fuel To check the fuel availability, ask an auto club, or
system and also damage plastic and rubber parts. contact a major oil company that does business in the
That damage would not be covered under your country where you will be driving.
warranty.
5-7
Filling the Tank To open the fuel filler door,
pull up on the release
lever located on the floor
on the outboard side of the
{CAUTION: drivers seat.
Fuel vapor burns violently and a fuel fire can

cause bad injuries. To help avoid injuries to
you and others, read and follow all the
instructions on the pump island. Turn off your
engine when you are refueling. Do not smoke
if you are near fuel or refueling your vehicle.
Do not use cellular phones. Keep sparks,
flames, and smoking materials away from fuel. The tethered fuel cap
Do not leave the fuel pump unattended when is located behind a
refueling your vehicle. This is against the law hinged fuel door on the
in some places. Do not re-enter the vehicle passengers side of
while pumping fuel. Keep children away from the vehicle.
the fuel pump; never let children pump fuel.
5-8
To remove the fuel cap, turn it slowly to the left When replacing the fuel cap, turn it to the right
(counterclockwise). The fuel cap has a spring in it; if the (clockwise) until it clicks. Make sure the cap is fully
cap is released too soon, it will spring back to the right. installed. The diagnostic system can determine if the
fuel cap has been left off or improperly installed.
This would allow fuel to evaporate into the atmosphere.
{CAUTION: See Malfunction Indicator Lamp on page 3-34.
Fuel can spray out on you if you open the fuel

cap too quickly. If you spill fuel and then
{CAUTION:
something ignites it, you could be badly burned.
This spray can happen if your tank is nearly full, If a fire starts while you are refueling, do not
and is more likely in hot weather. Open the fuel remove the nozzle. Shut off the flow of fuel by
cap slowly and wait for any hiss noise to stop. shutting off the pump or by notifying the
Then unscrew the cap all the way. station attendant. Leave the area immediately.
Be careful not to spill fuel. Do not top off or overfill the Notice: If you need a new fuel cap, be sure to get
tank and wait a few seconds after you have finished the right type. Your dealer/retailer can get one
pumping before removing the nozzle. Clean fuel for you. If you get the wrong type, it may not fit
from painted surfaces as soon as possible. properly. This may cause your malfunction indicator
See Washing Your Vehicle on page 5-82. lamp to light and may damage your fuel tank and
emissions system. See Malfunction Indicator Lamp
on page 3-34.
5-9
Filling a Portable Fuel Container Checking Things Under
the Hood
{CAUTION:
Never fill a portable fuel container while it is {CAUTION:
in your vehicle. Static electricity discharge
from the container can ignite the fuel vapor. An electric fan under the hood can start up
You can be badly burned and your vehicle and injure you even when the engine is not
damaged if this occurs. To help avoid injury running. Keep hands, clothing, and tools away
to you and others: from any underhood electric fan.
Dispense fuel only into approved
containers.
Do not fill a container while it is inside a
vehicle, in a vehicles trunk, pickup bed, {CAUTION:
or on any surface other than the ground.
Bring the fill nozzle in contact with the Things that burn can get on hot engine parts
inside of the fill opening before operating and start a fire. These include liquids like fuel,
the nozzle. Contact should be maintained
oil, coolant, brake fluid, windshield washer and
until the filling is complete.
other fluids, and plastic or rubber. You or
Do not smoke while pumping fuel.
others could be burned. Be careful not to drop
Do not use a cellular phone while or spill things that will burn onto a hot engine.
pumping fuel.
5-10
Hood Release
To open the hood, do the following:
1. Pull the hood release
handle inside the
vehicle. It is located on
the lower left side of
the instrument panel.
2. Then go to the front of the vehicle and lift up the

secondary hood release lever. The secondary hood
release lever is located under the front center of
the hood.
3. Lift the hood, release the hood prop from its retainer
and place the hood prop into the slot in the hood.
4. Before closing the hood, be sure all the filler caps are
on properly. Then lift the hood to relieve pressure on
the hood prop. Remove the hood prop from the slot
in the hood and return the prop to its retainer. Lower
the hood 12 inches (30 cm) above the vehicle and
release it to latch fully. Check to make sure the hood
is closed and repeat the process if necessary.
5-11
Engine Compartment Overview
When you open the hood on the engine, here is what you will see:
5-12
A. Engine Air Cleaner/Filter. See Engine Air Engine Oil
Cleaner/Filter on page 5-16.
B. Engine Oil Fill Cap. See When to Add Engine Oil If the engine oil pressure
under Engine Oil on page 5-13. light appears on the
instrument cluster, check
C. Engine Oil Dipstick. See Checking Engine Oil the engine oil level
under Engine Oil on page 5-13. right away.
D. Brake Fluid/Hydraulic Clutch Fluid Reservoir. See
Brake Fluid under Brakes on page 5-31 and
Hydraulic Clutch on page 5-18.
E. Power Steering Fluid Reservoir. See Power Steering For more information, see Oil Pressure Light on
Fluid on page 5-29. page 3-38. You should check the engine oil level
F. Engine Coolant Surge Tank. See Cooling System on regularly; this is an added reminder.
page 5-24.
G. Engine Compartment Fuse Block. See Engine Checking Engine Oil
Compartment Fuse Block on page 5-91. It is a good idea to check the engine oil every time you
H. Windshield Washer Fluid Reservoir. See Adding get fuel. In order to get an accurate reading, the oil
Washer Fluid under Windshield Washer Fluid must be warm and the vehicle must be on level ground.
on page 5-30. The engine oil dipstick handle is a yellow loop. See
I. Battery. See Battery on page 5-34. Engine Compartment Overview on page 5-12 for
the location of the engine oil dipstick.
1. Turn off the engine and give the oil several minutes
to drain back into the oil pan. If you do not do this,
the oil dipstick might not show the actual level.
2. Pull the dipstick and clean it with a paper towel or
cloth, then push it back in all the way. Remove it
again, keeping the tip down and check the level.
5-13
When to Add Engine Oil What Kind of Engine Oil to Use
If the oil is below the lower hole at the tip of the

dipstick (B), add at least one quart/liter of the
recommended oil. This section explains what kind of
oil to use. For engine oil crankcase capacity, see
Capacities and Specifications on page 5-94.
Notice: Do not add too much oil. If the engine has
so much oil that the oil level gets above the
upper hole (A) that shows the proper operating
range, the engine could be damaged.
See Engine Compartment Overview on page 5-12 for Look for three things:
the location of the engine oil fill cap. GM6094M
Be sure to add enough oil to put the level somewhere in Your vehicles engine requires oil meeting GM
the proper operating range, between the holes on the Standard GM6094M. Look for and use only an oil
dipstick. Push the dipstick all the way back in when you that meets GM Standard GM6094M.
are through.
SAE 5W-30
As shown in the viscosity chart, SAE 5W-30 is best
for your vehicle.
5-14
These numbers on an oil container show its If you are in an area of extreme cold, where the
viscosity, or thickness. Do not use other viscosity temperature falls below 20F (29C), it is
oils such as SAE 20W-50. recommended that you use either an SAE 5W-30
American Petroleum Institute (API) starburst symbol synthetic oil or an SAE 0W-30 oil. Both provide easier
cold starting and better protection for the engine at
Oils meeting these extremely low temperatures.
requirements should have
the starburst symbol on Engine Oil Additives
the container. This symbol
indicates that the oil Do not add anything to the oil. The recommended oils
has been certified by the with the starburst symbol that meet GM Standard
American Petroleum GM6094M are all you need for good performance and
Institute (API). engine protection.
When to Change Engine Oil
If any one of these is true for you, use the short trip/city
maintenance schedule:
Look for this information on the oil container, and use Most trips are less than 5 miles (8 km). This is
only those oils that are identified as meeting GM particularly important when outside temperatures
Standard GM6094M and have the starburst symbol on are below freezing.
the front of the oil container.
Most trips include extensive idling, such as frequent
Notice: Use only engine oil identified as meeting driving in stop-and-go traffic.
GM Standard GM6094M and showing the American
Petroleum Institute Certified For Gasoline Engines You frequently tow a trailer or use a carrier on top
starburst symbol. Failure to use the recommended of your vehicle.
oil can result in engine damage not covered by The vehicle is used for delivery service, police, taxi,
your warranty. or other commercial application.
5-15
Driving under these conditions causes engine oil to Engine Air Cleaner/Filter
break down sooner. If any one of these is true for your
vehicle, change the oil and filter every 3,000 miles The engine air cleaner/filter is located in the engine
(5 000 km) or 3 months, whichever occurs first. compartment on the passengers side of the vehicle.
If none of them is true, use the long trip/highway See Engine Compartment Overview on page 5-12
maintenance schedule. Change the oil and filter every for more information on location.
7,500 miles (12 500 km) or 12 months, whichever occurs
first. Driving a vehicle with a fully warmed engine When to Inspect the Engine Air
under highway conditions will cause engine oil to break Cleaner/Filter
down slower.
Inspect the engine air cleaner/filter every 15,000 miles
What to Do with Used Oil (25 000 km) and replace it every 30,000 miles
(50 000 km). If you are driving in dusty/dirty conditions,
Used engine oil contains certain elements that may be inspect the filter at each engine oil change.
unhealthy for your skin and could even cause cancer.
Do not let used oil stay on your skin for very long. Clean
your skin and nails with soap and water, or a good How to Inspect the Engine Air
hand cleaner. Wash or properly dispose of clothing or Cleaner/Filter
rags containing used engine oil. See the manufacturers
To inspect the engine air cleaner/filter remove the filter
warnings about the use and disposal of oil products.
from the vehicle and lightly shake the filter to release
Used oil can be a threat to the environment. If you loose dust and dirt. If the filter remains caked with dirt,
change your own oil, be sure to drain all the oil from the a new filter is required.
filter before disposal. Never dispose of oil by putting it
in the trash, pouring it on the ground, into sewers, or into
streams or bodies of water. Instead, recycle it by
taking it to a place that collects used oil. If you have a
problem properly disposing of used oil, ask your
dealer/retailer, a service station, or a local recycling
center for help.
5-16
To inspect or replace the filter, do the following:
{CAUTION:
Operating the engine with the air cleaner/filter
off can cause you or others to be burned.
The air cleaner not only cleans the air; it helps
to stop flames if the engine backfires. If it is
not there and the engine backfires, you could
be burned. Do not drive with it off, and be
careful working on the engine with the air
cleaner/filter off.
Notice: If the air cleaner/filter is off, a backfire

can cause a damaging engine fire. And, dirt can
1. Remove the four screws that hold the cover on. easily get into your engine, which will damage
it. Always have the air cleaner/filter in place when
2. Lift off the cover. you are driving.
3. Inspect or replace the engine air cleaner/filter.
4. Put the cover back on tightly and tighten the screws.
See Part A: Scheduled Maintenance Services on
page 6-4 for replacement intervals.
5-17
Automatic Transmission Fluid Hydraulic Clutch
It is not necessary to check the transmission fluid level. There is one reservoir for both the brake and the
If a leak occurs, take the vehicle to the dealer/retailer hydraulic clutch fluid. See Brakes on page 5-31
service department and have it repaired as soon as for more information.
possible. You may also have your fluid level checked by The hydraulic clutch linkage in your vehicle is
your dealer/retailer or service center when you have
self-adjusting. The master cylinder reservoir is filled
your oil changed. with hydraulic fluid.
Notice: Use of automatic transmission fluid labeled It is not necessary to regularly check the fluid unless
other than ESSO LT71141 or TOTAL ATF H50235 you suspect there is a leak in the system. Adding fluid
may damage your vehicle, and the damages may will not correct a leak.
not be covered by your warranty. Always use
ESSO LT71141 or TOTAL ATF H50235 labeled A fluid loss in this system could indicate a problem.
automatic transmission fluid. Have the system inspected and repaired.
When to Check and What to Use

Manual Transmission Fluid
Refer to the Maintenance Schedule to determine
It is not necessary to check the manual transmission how often you should check the fluid level in your
fluid level. A transmission fluid leak is the only reason master cylinder reservoir and for the proper fluid.
for fluid loss. If a leak occurs, take the vehicle to See Part B: Owner Checks and Services on page 6-19
the dealer/retailer service department and have it and Part D: Recommended Fluids and Lubricants
repaired as soon as possible. You may also have your on page 6-26.
fluid level checked by your dealer/retailer when you
have your oil changed. See Part D: Recommended
Fluids and Lubricants on page 6-26 for the proper fluid
to use.
5-18
How to Check and Add Fluid Engine Coolant
The cooling system in your vehicle is filled with
DEX-COOL engine coolant. This coolant is designed
to remain in your vehicle for five years or 150,000 miles
(240 000 km), whichever occurs first, if you add only
DEX-COOL extended life coolant.
The following explains your cooling system and how to
add coolant when it is low. If you have a problem
with engine overheating, see Engine Overheating on
page 5-22.
A 50/50 mixture of clean, drinkable water and
DEX-COOL coolant will:
Give freezing protection down to 34F (37C).
Give boiling protection up to 265F (129C).
Protect against rust and corrosion.
You do not need to check the fluid level unless you Help keep the proper engine temperature.
suspect a clutch problem. To check the fluid level, look
on the side of the reservoir. If the fluid reaches the
Let the warning lights and gages work as
MAX (A) mark on the reservoir, the fluid level is correct. they should.
If the fluid does not reach the MIN (B) mark, then Notice: Using coolant other than DEX-COOL may
fluid needs to be added. The reservoir is located near cause premature engine, heater core, or radiator
the back of the engine compartment on the drivers side corrosion. In addition, the engine coolant may
of the vehicle. See Engine Compartment Overview require changing sooner, at the first maintenance
on page 5-12 for more information on location. service after each 30,000 miles (50 000 km) or
24 months, whichever occurs first. Any repairs
would not be covered by your warranty. Always use
DEX-COOL (silicate-free) coolant in your vehicle.
5-19
What to Use If you have to add coolant more than four times a year,
have your dealer/retailer check your cooling system.
Use a mixture of one-half clean, drinkable water and
one-half DEX-COOL coolant which will not damage Notice: If you use extra inhibitors and/or additives in
aluminum parts. If you use this coolant mixture, you do your vehicles cooling system, you could damage
not need to add anything else. your vehicle. Use only the proper mixture of the
engine coolant listed in this manual for the cooling
system. See Part D: Recommended Fluids and
{CAUTION: Lubricants on page 6-26 for more information.
Checking Coolant
Adding only plain water to your cooling
system can be dangerous. Plain water, or
some other liquid such as alcohol, can boil
before the proper coolant mixture will. Your
vehicles coolant warning system is set for the
proper coolant mixture. With plain water or the
wrong mixture, your engine could get too hot
but you would not get the overheat warning.
Your engine could catch fire and you or others
could be burned. Use a 50/50 mixture of clean,
drinkable water and DEX-COOL coolant.
Notice: If you use an improper coolant mixture, your

engine could overheat and be badly damaged. The
repair cost would not be covered by your warranty. The engine coolant surge tank is located in the rear of
Too much water in the mixture can freeze and crack the engine compartment on the drivers side of the
the engine, radiator, heater core, and other parts. vehicle. See Engine Compartment Overview on
page 5-12 for more information on location.
5-20
Adding Coolant
{CAUTION: If you need more coolant, add the proper DEX-COOL
coolant mixture at the coolant surge tank, but only
when the engine is cool. If the coolant surge tank is
Turning the surge tank pressure cap when the empty, a special fill procedure is necessary. See Engine
engine and radiator are hot can allow steam Overheating on page 5-22 for instructions on How to
and scalding liquids to blow out and burn you Add Coolant to the Coolant Surge Tank.
badly. Never turn the surge tank pressure
cap even a little when the engine and
radiator are hot. {CAUTION:
To check the engine coolant, the vehicle must be on a You can be burned if you spill coolant on hot
level surface. When your engine is cold, the coolant engine parts. Coolant contains ethylene glycol,
level should be between the Maximum (A) and and it will burn if the engine parts are hot
Minimum (B) marks on the coolant surge tank. The level enough. Do not spill coolant on a hot engine.
rises at engine operation temperature and drops
again when the engine cools down.
When replacing the pressure cap, make sure it is
hand-tight and fully seated.
5-21
Coolant Surge Tank Pressure Cap If Steam Is Coming From Your Engine
Notice: If the pressure cap is not tightly installed,
coolant loss and possible engine damage may occur.
Be sure the cap is properly and tightly secured.
{CAUTION:
The coolant surge tank pressure cap must be fully
installed on the coolant surge tank. See Engine Steam from an overheated engine can burn
Compartment Overview on page 5-12 for more you badly, even if you just open the hood.
information on location. Stay away from the engine if you see or hear
steam coming from it. Just turn it off and get
Engine Overheating everyone away from the vehicle until it cools
down. Wait until there is no sign of steam or
You will find a coolant temperature gage on your coolant before you open the hood.
vehicles instrument panel cluster. See Engine Coolant
Temperature Gage on page 3-33. If you keep driving when your engine is
overheated, the liquids in it can catch fire.
You or others could be badly burned. Stop
your engine if it overheats, and get out of the
vehicle until the engine is cool.
Notice: If your engine catches fire because you

keep driving with no coolant, your vehicle can
be badly damaged. The costly repairs would not be
covered by your warranty.
5-22
If No Steam Is Coming From Your If you no longer have the overheat warning, you can
drive. Just to be safe, drive slower for about 10 minutes.
Engine If the warning does not come back on, you can drive
If you get an engine overheat warning, but see or normally.
hear no steam, the problem may not be too serious. If the warning continues and you have not stopped, pull
Sometimes the engine can get a little too hot when you: over, stop, and park your vehicle right away.
Climb a long hill on a hot day. If there is still no sign of steam, you can idle the engine
Stop after high-speed driving. for three minutes while you are parked. If you still
have the warning, turn off the engine and get everyone
Idle for long periods in traffic. out of the vehicle until it cools down.
If you get the overheat warning with no sign of steam, You may decide not to lift the hood, but to get service
try this for a minute or so: help right away.
1. In heavy traffic, let the engine idle in NEUTRAL (N)
while stopped. If it is safe to do so, pull off the road,
shift to PARK (P) or NEUTRAL (N) and let the
engine idle.
2. Turn on your heater to full hot at the highest fan
speed and open the windows as necessary.
5-23
Cooling System
When you decide it is safe to lift the hood, here is what {CAUTION:
you will see:
An electric engine cooling fan under the hood
can start up even when the engine is not
running and can injure you. Keep hands,
clothing, and tools away from any underhood
electric fan.
If the coolant inside the coolant surge tank is boiling,

do not do anything else until it cools down. The vehicle
should be parked on a level surface. Make sure that
the air conditioning is turned off.
The coolant level should be between the Minimum and
Maximum marks on the coolant surge tank when the
engine is cool. If it is not, you may have a leak at the
pressure cap or in the radiator hoses, heater hoses,
A. Coolant Surge Tank with Pressure Cap radiator, water pump, or somewhere else in the cooling
system.
B. Electric Engine Cooling Fan
5-24
How to Add Coolant to the Coolant
{CAUTION: Surge Tank
Notice: This vehicle has a specific coolant fill
Heater and radiator hoses, and other engine procedure. Failure to follow this procedure could
parts, can be very hot. Do not touch them. cause your engine to overheat and be severely
If you do, you can be burned. damaged.
Do not run the engine if there is a leak. If you If you have not found a problem yet, check to see if
run the engine, it could lose all coolant. That coolant is visible in the surge tank. If coolant is visible
could cause an engine fire, and you could be but the coolant level is not between the Minimum
burned. Get any leak fixed before you drive the and Maximum marks, add a 50/50 mixture of clean,
drinkable water and proper coolant at the coolant surge
vehicle.
tank, but be sure the cooling system, including the
coolant surge tank pressure cap, is cool before you
If there seems to be no leak, with the engine on, check do it. See Engine Coolant on page 5-19 for more
to see if the electric engine cooling fan is running. information.
If the engine is overheating, the fan should be running.
If it is not, your vehicle needs service.
Notice: Engine damage from running the engine
without coolant is not covered by the warranty.
5-25
If no coolant is visible in the surge tank, add coolant as
follows:
{CAUTION:
{CAUTION: Adding only plain water to your cooling
system can be dangerous. Plain water, or
Steam and scalding liquids from a hot cooling some other liquid such as alcohol, can boil
system can blow out and burn you badly. They before the proper coolant mixture will. Your
are under pressure, and if you turn the coolant vehicles coolant warning system is set for the
surge tank pressure cap even a little they proper coolant mixture. With plain water or the
can come out at high speed. Never turn the wrong mixture, your engine could get too hot
cap when the cooling system, including the but you would not get the overheat warning.
coolant surge tank pressure cap, is hot. Wait Your engine could catch fire and you or others
for the cooling system and coolant surge tank could be burned. Use a 50/50 mixture of clean,
pressure cap to cool if you ever have to turn drinkable water and a proper coolant.
the pressure cap.
Notice: In cold weather, water can freeze and crack
the engine, radiator, heater core and other parts.
Use the recommended coolant and the proper
coolant mixture.
5-26
{CAUTION:
You can be burned if you spill coolant on hot
engine parts. Coolant contains ethylene glycol
and it will burn if the engine parts are hot
enough. Do not spill coolant on a hot engine.
1. You can remove the coolant surge tank pressure

cap when the cooling system, including the
coolant surge tank pressure cap and upper
radiator hose, is no longer hot. Turn the
pressure cap slowly counterclockwise about
two or two and one-half turns.
2. Then keep turning the pressure cap slowly, and
If you hear a hiss, wait for that to stop. This will remove it.
allow any pressure still left to be vented out
the discharge hose.
5-27
4. With the coolant surge tank pressure cap off, start
the engine and let it run until you can feel the upper
radiator hose getting hot. Watch out for the
engine cooling fan.
By this time, the coolant level inside the coolant
surge tank may be lower. If the level is lower than
the Maximum mark, add more of the proper mixture
to the coolant surge tank until the level reaches
the mark.
5. Then replace the pressure cap. Be sure the
pressure cap is hand-tight and fully seated.
See your dealer/retailer, if necessary.
3. Fill the coolant surge tank with the proper mixture

to the Maximum mark on the coolant surge tank.
Wait about five minutes, then check to see if
the level is below the mark. If the level is below the
Maximum mark, add additional coolant to bring
the level up to the mark. Repeat this procedure until
the level remains constant at the Maximum mark
for at least five minutes.
5-28
Power Steering Fluid
When to Check Power Steering Fluid
The power steering fluid reservoir is located toward the
front of the engine compartment on the drivers side
of the vehicle. See Engine Compartment Overview on
page 5-12 for reservoir location.
It is not necessary to regularly check power steering
fluid unless you suspect there is a leak in the system or
you hear an unusual noise. A fluid loss in this system
could indicate a problem. Have the system inspected
and repaired.
How to Check Power Steering Fluid

Turn the key off and let the engine compartment cool The level should be between the MIN (B) and MAX (A)
down. Then check the fluid level. marks on the reservoir. If the level is below the MIN (B)
mark, add the power steering fluid to the appropriate
level. Replace the cap and completely tighten it.
What to Use
To determine what kind of fluid to use, see Part D:
Recommended Fluids and Lubricants on page 6-26.
Always use the proper fluid. Failure to use the proper
fluid can cause leaks and damage hoses and seals.
5-29
Windshield Washer Fluid Notice:
When using concentrated washer fluid, follow
What to Use the manufacturers instructions for adding
water.
When you need windshield washer fluid, be sure to read
the manufacturers instructions before use. If you will Do not mix water with ready-to-use washer fluid.
be operating your vehicle in an area where the Water can cause the solution to freeze and
temperature may fall below freezing, use a fluid that damage your washer fluid tank and other parts
has sufficient protection against freezing. of the washer system. Also, water does not
clean as well as washer fluid.
Adding Washer Fluid Fill the washer fluid tank only three-quarters full
when it is very cold. This allows for fluid
Open the cap with the
expansion if freezing occurs, which could
washer symbol on it.
damage the tank if it is completely full.
Add washer fluid until the
tank is full. See Engine Do not use engine coolant (antifreeze) in your
Compartment Overview on windshield washer. It can damage the vehicles
page 5-12 for reservoir windshield washer system and paint.
location.
5-30
Brakes It is not a good idea to top off the brake fluid. Adding
brake fluid will not correct a leak. If fluid is added when
Brake Fluid the linings are worn, there will be too much fluid when
new brake linings are installed. Add or remove brake
The master cylinder fluid, as necessary, only when work is done on the
reservoir is filled with brake hydraulic system
DOT-3 brake fluid.
See Engine Compartment
Overview on page 5-12
for the location of the
{CAUTION:
reservoir.
If your vehicle has too much brake fluid, it can
spill on the engine. The fluid will burn if the
engine is hot enough. You or others could be
burned, and your vehicle could be damaged.
Add brake fluid only when work is done on the
There are only two reasons why the brake fluid level brake hydraulic system.
in the reservoir might go down. The first is that the brake
fluid goes down to an acceptable level during normal
brake lining wear. When new linings are put in, the fluid When the brake fluid falls to a low level, the brake
level goes back up. The other reason is that fluid is warning light will come on. See Brake System Warning
leaking out of the brake hydraulic system. If it is, you Light on page 3-31.
should have the brake hydraulic system fixed, since
a leak means that sooner or later the brakes will
not work well.
5-31
What to Add Notice:
When you do need brake fluid, use only DOT-3 brake Using the wrong fluid can badly damage brake
fluid. Use new brake fluid from a sealed container only. hydraulic system parts. For example, just a
See Part D: Recommended Fluids and Lubricants on few drops of mineral-based oil, such as engine
page 6-26. oil, in the brake hydraulic system can damage
brake hydraulic system parts so badly that they
Always clean the brake fluid reservoir cap and the area will have to be replaced. Do not let someone
around the cap before removing it. This helps keep put in the wrong kind of fluid.
dirt from entering the reservoir.
If you spill brake fluid on your vehicles painted
surfaces, the paint finish can be damaged.
{CAUTION: Be careful not to spill brake fluid on your
vehicle. If you do, wash it off immediately.
See Washing Your Vehicle on page 5-82.
With the wrong kind of fluid in the brake
hydraulic system, the brakes might not work Brake Wear
well. This could cause a crash. Always use the
proper brake fluid. Your vehicle has disc brakes. Disc brake pads have
built-in wear indicators that make a high-pitched warning
sound when the brake pads are worn and new pads
are needed. The sound can come and go or be heard all
the time your vehicle is moving, except when you are
pushing on the brake pedal firmly.
5-32
Brake Pedal Travel
{CAUTION: See your dealer/retailer if the brake pedal does not
return to normal height, or if there is a rapid increase in
pedal travel. This could be a sign that brake service
The brake wear warning sound means that soon might be required.
the brakes will not work well. That could lead to
an accident. When you hear the brake wear Brake Adjustment
warning sound, have your vehicle serviced. Every time you apply the brakes, with or without the
vehicle moving, the brakes adjust for wear.
Notice: Continuing to drive with worn-out brake Replacing Brake System Parts
pads could result in costly brake repair.
The braking system on a vehicle is complex.
Some driving conditions or climates can cause a brake Its many parts have to be of top quality and work well
squeal when the brakes are first applied or lightly together if the vehicle is to have really good braking.
applied. This does not mean something is wrong with Your vehicle was designed and tested with top-quality
the brakes. brake parts. When you replace parts of the braking
Properly torqued wheel nuts are necessary to help system for example, when the brake linings wear
prevent brake pulsation. When tires are rotated, down and you need new ones put in be sure you
inspect brake pads for wear and evenly tighten wheel get new approved replacement parts. If you do not,
nuts in the proper sequence to torque specifications the brakes might not work properly. For example,
in Capacities and Specifications on page 5-94. if someone puts in brake linings that are wrong for
your vehicle, the balance between the front and rear
Brake linings should always be replaced as complete
brakes can change for the worse. The braking
axle sets.
performance you have come to expect can change in
See Brake System Inspection on page 6-25. many other ways if someone puts in the wrong
replacement brake parts.
5-33
Battery Vehicle Storage
Your vehicle has a maintenance free battery. When it is
time for a new battery, see your dealer/retailer for {CAUTION:
one that has the replacement number shown on the
original batterys label. See Engine Compartment
Overview on page 5-12 for battery location. Batteries have acid that can burn you and gas
Warning: Battery posts, terminals, and related that can explode. You can be badly hurt if you
accessories contain lead and lead compounds, are not careful. See Jump Starting on page 5-35
chemicals known to the State of California to cause for tips on working around a battery without
cancer and reproductive harm. Wash hands after getting hurt.
handling.
Infrequent Usage: If you drive your vehicle infrequently,
remove the black, negative () cable from the battery.
This will help keep the battery from running down.
Extended Storage: For extended storage of your vehicle,
remove the black, negative () cable from the battery or
use a battery trickle charger. This will help maintain the
charge of the battery over an extended period of time.
5-34
Jump Starting Notice: Ignoring these steps could result in costly
damage to your vehicle that would not be covered
If your battery has run down, you may want to use by your warranty.
another vehicle and some jumper cables to start your Trying to start your vehicle by pushing or pulling it
vehicle. Be sure to use the following steps to do it safely. will not work, and it could damage your vehicle.
1. Check the other vehicle. It must have a 12-volt
battery with a negative ground system.
{CAUTION:
Notice: If the other vehicles system is not a 12-volt
Batteries can hurt you. They can be dangerous system with a negative ground, both vehicles can
be damaged. Only use vehicles with 12-volt systems
because:
with negative grounds to jump start your vehicle.
They contain acid that can burn you.
2. Get the vehicles close enough so the jumper cables
They contain gas that can explode or can reach, but be sure the vehicles are not touching
ignite. each other. If they are, it could cause a ground
They contain enough electricity to connection you do not want. You would not be able
burn you. to start your vehicle, and the bad grounding
If you do not follow these steps exactly, some could damage the electrical systems.
or all of these things can hurt you. To avoid the possibility of the vehicles rolling, set
the parking brake firmly on both vehicles involved
in the jump start procedure. Put an automatic
transmission in PARK (P) or a manual transmission
in NEUTRAL before setting the parking brake.
5-35
Notice: If you leave your radio or other accessories
on during the jump starting procedure, they could
be damaged. The repairs would not be covered {CAUTION:
by your warranty. Always turn off your radio and
other accessories when jump starting your vehicle. An electric fan can start up even when the
3. Turn off the ignition on both vehicles. Unplug engine is not running and can injure you.
unnecessary accessories plugged into the cigarette Keep hands, clothing and tools away from any
lighter or the accessory power outlet. Turn off underhood electric fan.
the radio and all lamps that are not needed.
This will avoid sparks and help save both batteries.
And it could save the radio!
4. Open the hoods and locate the batteries. Find the {CAUTION:
positive (+) and negative () terminal locations on
each vehicle. Your vehicles positive (+) terminal is
located under a red tethered cap on the battery. Using a match near a battery can cause battery
The negative () terminal is located under a gas to explode. People have been hurt doing
black tethered cap on the battery. See Engine this, and some have been blinded. Use a
Compartment Overview on page 5-12 for more flashlight if you need more light.
information on location. Flip the caps up to access Be sure the battery has enough water. You do
the positive (+) and negative () terminals.
not need to add water to the battery installed
in your new vehicle. But if a battery has filler
caps, be sure the right amount of fluid is there.
If it is low, add water to take care of that first.
If you dont, explosive gas could be present.
5-36
5. Check that the jumper cables do not have loose or
CAUTION: (Continued) missing insulation. If they do, you could get a
shock. The vehicles could be damaged too.
Before you connect the cables, here are some
Battery fluid contains acid that can burn you. things you should know. Positive (+) will go
Do not get it on you. If you accidentally get it to positive (+) or to a remote positive (+) terminal if
in your eyes or on your skin, flush the place the vehicle has one. Negative () will go to a
with water and get medical help immediately. heavy, unpainted metal engine part or to a remote
negative () terminal if the vehicle has one.
Do not connect positive (+) to negative () or you
will get a short that would damage the battery
{CAUTION: and maybe other parts too. And do not connect the
negative () cable to the negative () terminal on
the dead battery because this can cause sparks.
Fans or other moving engine parts can injure
you badly. Keep your hands away from moving
parts once the engine is running.
5-37
6. Connect the red 9. Connect the other end
positive (+) cable to the of the negative ()
positive (+) terminal cable at least 18 inches
of the dead battery. (45 cm) away from
the dead battery,
but not near engine
parts that move.
Use a remote positive (+) terminal if the vehicle The electrical connection is just as good there, and
has one. the chance of sparks getting back to the battery
is much less.
7. Do not let the other end touch metal. Connect it to
the positive (+) terminal of the good battery. Use a 10. Now start the vehicle with the good battery and run
remote positive (+) terminal if the vehicle has one. the engine for a while.
8. Now connect the black negative () cable to the 11. Try to start the vehicle that had the dead battery.
negative () terminal of the good battery. Use a If it will not start after a few tries, it probably needs
remote negative () terminal if the vehicle has one. service.
Do not let the other end touch anything until the
next step. The other end of the negative () cable
does not go to the dead battery. It goes to a
heavy, unpainted metal engine part or to a remote
negative () terminal on the vehicle with the
dead battery.
5-38
Notice: If the jumper cables are connected or To disconnect the jumper cables from both vehicles,
removed in the wrong order, electrical shorting may do the following:
occur and damage the vehicle. The repairs would 1. Disconnect the black negative () cable from the
not be covered by your warranty. Always connect vehicle that had the dead battery.
and remove the jumper cables in the correct
order, making sure that the cables do not touch 2. Disconnect the black negative () cable from the
each other or other metal. vehicle with the good battery.
3. Disconnect the red positive (+) cable from the
vehicle with the good battery.
4. Disconnect the red positive (+) cable from the other
vehicle.
5. Return the caps over the positive (+) and
negative () terminals to their original positions.
Jumper Cable Removal

A. Heavy, Unpainted Metal Engine Part or Remote
Negative () Terminal
B. Good Battery or Remote Positive (+) and Remote
Negative () Terminals
C. Dead Battery or Remote Positive (+) Terminal
5-39
Headlamp Aiming Bulb Replacement
Headlamp aim has been preset at the factory and For the proper type of replacement bulbs, see
should need no further adjustment. Replacement Bulbs on page 5-48.
However, if your vehicle is damaged in a crash, For any bulb changing procedure not listed in this
the headlamp aim may be affected. Aim adjustment section, contact your dealer/retailer.
to the low-beam headlamps may be necessary if
oncoming drivers flash their high-beam headlamps
at you (for vertical aim).
Halogen Bulbs
If the headlamps need to be re-aimed, it is
recommended that you take the vehicle to your
dealer/retailer for service.
{CAUTION:
Halogen bulbs have pressurized gas inside and
can burst if you drop or scratch the bulb. You or
others could be injured. Be sure to read and
follow the instructions on the bulb package.
5-40
Headlamps
To replace a headlamp bulb:
1. Open the hood. See Hood Release on page 5-11
2. For wagon models, remove the two bolts from the
top of the headlamp assembly and one nut on the
inside that retains the headlamp assembly.
For hatchback models, remove the four screws and
the radiator grill. Then remove the three bolts
and the headlamp assembly.
3. Disconnect the wiring harness connector from the
rear of the bulb.
Hatchback Models
4. Remove the headlamp cap (A for the low-beam
or B for the high-beam headlamp) by turning it
counterclockwise.
5. Release the spring that retains the bulb.
6. Remove the old bulb.
7. Install a new bulb.
8. Reverse Steps 1 through 5 to install the headlamp
assembly.
Wagon Models
5-41
Front Turn Signal and
Parking Lamps
To replace a front turn signal or parking lamp bulb:
1. Open the hood. See Hood Release on page 5-11
2. Remove the two bolts from the top of the headlamp
assembly and one nut on the inside that retains the
headlamp assembly.
Hatchback Models
3. Turn the bulb socket counterclockwise.

4. Pull the bulb socket out of the lamp housing.
5. Press the bulb inward and turn it counterclockwise
to remove it from the bulb socket.
6. Install the new bulb into the bulb socket by pressing
it in and turning it clockwise.
7. Reinstall the bulb socket into the lamp housing by
Wagon Models turning it clockwise.
8. Reverse Steps 1 through 2 to install the assembly.
5-42
Turn Signal Lamps (Side)
Your vehicle may have this side turn signal lamp. It will
be located between the front door and the wheel well.
To replace this bulb:
1. Locate the bulb by reaching underneath the vehicle
where the side turn signal lamp is located.
2. Remove the side turn signal lamp assembly by
pulling it forward.
3. Turn the bulb socket counterclockwise.
4. Remove the bulb from the lamp housing by pulling

the bulb straight out of the socket.
5. Install the new bulb into the bulb socket by pushing
it in and turning it clockwise.
6. Push the side turn signal lamp assembly back into
its original position.
5-43
Sidemarker Lamps (Front) Sidemarker Lamps (Rear)
To replace a front sidemarker bulb: To replace a rear sidemarker bulb:
1. Open the hood. See Hood Release on page 5-11 1. Reach inside of the rear bumper and locate the
for more information. socket.
2. Remove the headlamp assembly.
3. Turn the front sidemarker bulb socket
counterclockwise.
4. Pull the front sidemarker bulb socket out of the front
bumper.
2. Turn the rear sidemarker bulb socket

counterclockwise.
3. Pull the rear sidemarker bulb socket out of the rear
bumper.
4. Pull the old bulb straight out from the bulb socket.
5. Pull the old bulb straight out of the bulb socket 5. Push the new bulb straight into the socket.
6. Push the new bulb straight into the socket. 6. Reverse Steps 1 through 3 to install the bulb socket.
7. Reverse Steps 1 through 5 to install the assembly.
5-44
Center High-Mounted Stoplamp Center High-Mounted Stoplamp
(CHMSL) (Hatchback) (CHMSL) (Wagon)
To replace a CHMSL bulb on a hatchback model: To replace a CHMSL bulb on a wagon model:
1. Open the liftgate. See Liftgate on page 2-10 for 1. Open the liftgate. See Liftgate on page 2-10 for
more information. more information.
2. Pry off the trim from the liftgate and remove the 2. Remove the two screws and the liftgate trim cover.
two screws.
3. Remove the bulb socket from the lamp housing.
3. Remove the bulb socket from the lamp housing.
4. Remove the bulb by pulling it straight out of the
4. Remove the bulb by pulling it straight out of the bulb socket.
bulb socket.
5. Install the new bulb.
5. Install the new bulb.
6. Reinstall the liftgate trim cover and secure with the
6. Reverse Steps 1 through 3 to reinstall the lamp two screws to secure.
assembly.
5-45
Taillamps, Turn Signal, and Taillamps, Turn Signal, Stoplamps
Stoplamps (Hatchback) and Back-up Lamps (Wagon)
To replace one of these bulbs: To replace one of these bulbs:
1. Open the liftgate. See Liftgate on page 2-10 for 1. Open the liftgate. See Liftgate on page 2-10 for
more information. more information.
2. Remove the two screws and the taillamp assembly.
2. Remove the two screws from the taillamp assembly.

3. Remove the bulb socket by turning it 3. Remove the taillamp assembly from the vehicle.
counterclockwise from the taillamp assembly.
4. Remove the bulb socket by turning it
4. Remove the bulb from the socket by pressing the counterclockwise from the taillamp assembly.
bulb and turning it counterclockwise.
5. Remove the bulb from the socket by pressing the
5. Install the appropriate new bulb into the socket. bulb and turning it counterclockwise.
6. Reverse Steps 1 through 3 to install the lamp
assembly.
5-46
6. Install the appropriate new bulb into the socket. 4. Remove the bulb from the socket by pressing the
7. Reverse Steps 1 through 4 to install the lamp bulb and turning it counterclockwise.
assembly. 5. Install the appropriate new bulb into the socket.
6. Reinstall the protective cover.
Taillamps, Stoplamps and Back-up
Lamps (Hatchback) License Plate Lamp
To replace one of these bulbs: To replace one of these bulbs:
1. Open the liftgate. See Liftgate on page 2-10 for
more information.
2. Remove the protective cover.
1. Remove the two screws holding each of the license

plate lamps.
2. Turn and pull the license plate lamp toward you
3. Remove the bulb socket by turning it through the opening.
counterclockwise.
5-47
3. Turn the bulb socket counterclockwise and pull the
bulb straight out of the socket.
Windshield Wiper Blade
4. Install the new bulb. Replacement
5. Reverse Steps 1 through 3 to reinstall the license Windshield wiper blades should be inspected for wear or
plate lamp. cracking. See Wiper Blade Check for more information.
Replacement blades come in different types and are
Replacement Bulbs removed in different ways. For the proper type,
see Maintenance Replacement Parts on page 5-95.
Exterior Lamps Bulb Number Here is how to remove and replace the windshield
wiper blade:
Back-up 94535571
CHMSL, Front and Rear 94535587
Sidemarker
License Plate Lamp 94535587
Headlamps
High-Beam 94535541
Low-Beam 94535546
Stoplamp and Taillamp 94535574
Turn Signal - Front and
94535578
Parking Lamp
Turn Signal - Rear 94535572
For replacement bulbs not listed here, contact your

dealer/retailer. 1. Pull the windshield wiper arm away from the
windshield.
2. Press the retaining clip (A) and pull the wiper blade
off the arm.
3. Install a new blade by reversing Steps 1 and 2.
5-48
Tires
Your new vehicle comes with high-quality tires
made by a leading tire manufacturer. If you ever
have questions about your tire warranty and where Underinflated tires pose the same
to obtain service, see your vehicle Warranty danger as overloaded tires. The
booklet for details. resulting accident could cause serious
injury. Check all tires frequently to
maintain the recommended pressure.
{CAUTION: Tire pressure should be checked when
your vehicles tires are cold. See
Inflation - Tire Pressure on page 5-56.
Poorly maintained and improperly used Overinflated tires are more likely to be
tires are dangerous. cut, punctured, or broken by a sudden
Overloading your vehicles tires can impact such as when you hit a
cause overheating as a result of pothole. Keep tires at the
too much flexing. You could have recommended pressure.
an air-out and a serious accident. Worn, old tires can cause accidents.
See Loading Your Vehicle on If the tires tread is badly worn,
page 4-18. or if your vehicles tires have been
CAUTION: (Continued) damaged, replace them.
5-49
Tire Sidewall Labeling (A) Tire Size: The tire size is a combination of
letters and numbers used to define a particular
Useful information about a tire is molded into its tires width, height, aspect ratio, construction type
sidewall. The examples below show a typical and service description. See the Tire Size
passenger car tire and a compact spare tire illustration later in this section for more detail.
sidewall.
(B) DOT (Department of Transportation):
The Department of Transportation (DOT) code
indicates that the tire is in compliance with the U.S.
Department of Transportation Motor Vehicle
Safety Standards.
(C) Tire Identification Number (TIN): The letters
and numbers following DOT code are the Tire
Identification Number (TIN). The TIN shows
the manufacturer and plant code, tire size, and
date the tire was manufactured. The TIN is molded
onto both sides of the tire, although only one side
may have the date of manufacture.
(D) Tire Ply Material: The type of cord and
number of plies in the sidewall and under the
tread.
(E) Uniform Tire Quality Grading (UTQG):
Passenger Car Tire Example
Tire manufacturers are required to grade
tires based on three performance factors:
treadwear, traction and temperature resistance.
For more information see Uniform Tire Quality
Grading on page 5-64.
5-50
(F) Maximum Cold Inflation Load Limit: (A) Temporary Use Only: The compact spare
Maximum load that can be carried and the tire or temporary use tire has a tread life of
maximum pressure needed to support that load. approximately 3,000 miles (5 000 km) and should
For information on recommended tire pressure see not be driven at speeds over 65 mph (105 km/h).
Inflation - Tire Pressure on page 5-56 and The compact spare tire is for emergency use when
Loading Your Vehicle on page 4-18. a regular road tire has lost air and gone flat.
See Compact Spare Tire on page 5-78 and If a
Tire Goes Flat on page 5-68.
(B) Tire Ply Material: The type of cord and
number of plies in the sidewall and under the
tread.
(C) Tire Identification Number (TIN): The Tire
Identification Number (TIN). The TIN shows
the manufacturer and plant code, tire size, and
date the tire was manufactured. The TIN is molded
onto both sides of the tire, although only one
side may have the date of manufacture.
(D) Maximum Cold Inflation Load
Limit: Maximum load that can be carried and
the maximum pressure needed to support
that load. See Compact Spare Tire on page 5-78
and Loading Your Vehicle on page 4-18.
Compact Spare Tire Example
5-51
(E) Tire Inflation: The temporary use tire or (B) Tire Width: The three-digit number indicates
compact spare tire should be inflated to 60 psi the tire section width in millimeters from sidewall
(420 kPa). For more information on tire pressure to sidewall.
and inflation see Inflation - Tire Pressure on
page 5-56. (C) Aspect Ratio: A two-digit number that
indicates the tire height-to-width measurements.
(F) Tire Size : A combination of letters and For example, if the tire size aspect ratio is 70,
numbers define a tires width, height, aspect ratio, as shown in item C of the illustration, it would
construction type and service description. mean that the tires sidewall is 70% as high as
The letter T as the first character in the tire size it is wide.
means the tire is for temporary use only.
(D) Construction Code: A letter code is used to
Tire Size indicate the type of ply construction in the tire.
The letter R means radial ply construction;
The following illustration shows an example of a the letter D means diagonal or bias ply
typical passenger car tire size. construction; and the letter B means belted-bias
ply construction.
(E) Rim Diameter: Diameter of the wheel in
inches.
(F) Service Description: These characters
represent the load range and the speed rating of a
tire. The load range represents the load carry
capacity a tire is certified to carry. The speed
(A) Passenger (P-Metric) Tire: The United States rating is the maximum speed a tire is certified to
version of a metric tire sizing system. The letter P carry a load. Speed ratings range from A to Z.
as the first character in the tire size means a
passenger vehicle tire engineered to standards set
by the U. S. Tire and Rim Association.
5-52
Tire Terminology and Definitions Cold Tire Pressure: The amount of air pressure
in a tire, measured in pounds per square inch
Air Pressure: The amount of air inside the (psi) or kilopascals (kPa) before a tire has built up
tire pressing outward on each square inch of the heat from driving. See Inflation - Tire Pressure
tire. Air pressure is expressed in pounds per on page 5-56.
square inch (psi) or kilopascal (kPa). Curb Weight: The weight of a motor vehicle with
Accessory Weight: This means the combined standard and optional equipment including the
weight of optional accessories. Some examples of maximum capacity of fuel, oil, and coolant,
optional accessories are, automatic transmission, but without passengers and cargo.
power steering, power brakes, power windows, DOT Markings: A code molded into the sidewall
power seats, and air conditioning. of a tire signifying that the tire is in compliance
Aspect Ratio: The relationship of a tires height with the U.S. Department of Transportation (DOT)
to its width. motor vehicle safety standards. The DOT code
includes the Tire Identification Number (TIN),
Belt: A rubber coated layer of cords that is an alphanumeric designator which can also identify
located between the plies and the tread. Cords the tire manufacturer, production plant, brand,
may be made from steel or other reinforcing and date of production.
materials.
GVWR: Gross Vehicle Weight Rating.
Bead: The tire bead contains steel wires wrapped See Loading Your Vehicle on page 4-18.
by steel cords that hold the tire onto the rim.
GAWR FRT: Gross Axle Weight Rating for the
Bias Ply Tire: A pneumatic tire in which the plies front axle. See Loading Your Vehicle on
are laid at alternate angles less than 90 degrees page 4-18.
to the centerline of the tread.
5-53
GAWR RR: Gross Axle Weight Rating for the rear Normal Occupant Weight: The number of
axle. See Loading Your Vehicle on page 4-18. occupants a vehicle is designed to seat multiplied
by 150 lbs (68 kg). See Loading Your Vehicle
Intended Outboard Sidewall: The side of on page 4-18.
an asymmetrical tire, that must always face
outward when mounted on a vehicle. Occupant Distribution: Designated seating
positions.
Kilopascal (kPa): The metric unit for air pressure.
Outward Facing Sidewall: The side of an
Light Truck (LT-Metric) Tire: A tire used on asymmetrical tire that has a particular side that
light duty trucks and some multipurpose passenger faces outward when mounted on a vehicle.
vehicles. The side of the tire that contains a whitewall, bears
Load Index: An assigned number ranging from white lettering, or bears manufacturer, brand,
1 to 279 that corresponds to the load carrying and/or model name molding that is higher
capacity of a tire. or deeper than the same moldings on the other
sidewall of the tire.
Maximum Inflation Pressure: The maximum air
pressure to which a cold tire can be inflated. Passenger (P-Metric) Tire: A tire used on
The maximum air pressure is molded onto the passenger cars and some light duty trucks and
sidewall. multipurpose vehicles.
Maximum Load Rating: The load rating for a tire Recommended Inflation Pressure: Vehicle
at the maximum permissible inflation pressure manufacturers recommended tire inflation
for that tire. pressure as shown on the tire placard. See
Inflation - Tire Pressure on page 5-56 and Loading
Maximum Loaded Vehicle Weight: The sum of Your Vehicle on page 4-18.
curb weight, accessory weight, vehicle capacity
weight, and production options weight.
5-54
Radial Ply Tire: A pneumatic tire in which the UTQGS (Uniform Tire Quality Grading
ply cords that extend to the beads are laid at Standards): A tire information system that
90 degrees to the centerline of the tread. provides consumers with ratings for a tires
traction, temperature, and treadwear. Ratings
Rim: A metal support for a tire and upon which are determined by tire manufacturers using
the tire beads are seated. government testing procedures. The ratings are
Sidewall: The portion of a tire between the tread molded into the sidewall of the tire. See Uniform
and the bead. Tire Quality Grading on page 5-64.
Speed Rating: An alphanumeric code assigned to Vehicle Capacity Weight: The number of
a tire indicating the maximum speed at which a designated seating positions multiplied by 150 lbs
tire can operate. (68 kg) plus the rated cargo load. See Loading
Your Vehicle on page 4-18.
Traction: The friction between the tire and the
road surface. The amount of grip provided. Vehicle Maximum Load on the Tire: Load on an
individual tire due to curb weight, accessory
Tread: The portion of a tire that comes into weight, occupant weight, and cargo weight.
contact with the road.
Vehicle Placard: A label permanently attached
Treadwear Indicators: Narrow bands, sometimes to a vehicle showing the vehicles capacity weight
called wear bars, that show across the tread of and the original equipment tire size and
a tire when only 1/16 inch (1.6 mm) of tread recommended inflation pressure. See Tire and
remains. See When It Is Time for New Tires on Loading Information Label under Loading
page 5-62. Your Vehicle on page 4-18.
5-55
Inflation - Tire Pressure A vehicle specific tire and loading information label is
attached to your vehicle. This label shows your vehicles
Tires need the correct amount of air pressure to operate original equipment tires and the correct inflation
effectively. pressures for your tires when they are cold.
The recommended cold tire inflation pressure, shown on
Notice: Do not let anyone tell you that the label, is the minimum amount of air pressure
under-inflation or over-inflation is all right. needed to support your vehicles maximum load carrying
It is not. If your tires do not have enough air capacity.
(under-inflation), you can get the following:
For additional information regarding how much weight
Too much flexing your vehicle can carry, and an example of the tire
Too much heat and loading information label, see Loading Your Vehicle
Tire overloading on page 4-18. How you load your vehicle affects
vehicle handling and ride comfort. Never load your
Premature or irregular wear vehicle with more weight than it was designed to carry.
Poor handling
Reduced fuel economy When to Check
If your tires have too much air (over-inflation), Check your tires once a month or more. Do not forget to
you can get the following: check the compact spare tire. For additional information
regarding the compact spare tire, see Compact Spare
Unusual wear Tire on page 5-78.
Poor handling
Rough ride
Needless damage from road hazards
5-56
How to Check Tire Pressure Monitor System
Use a good quality pocket-type gage to check tire The Tire Pressure Monitor System (TPMS) uses radio
pressure. You cannot tell if your tires are properly and sensor technology to check tire pressure levels.
inflated simply by looking at them. Radial tires may look The TPMS sensors monitor the air pressure in
properly inflated even when they are under-inflated. your vehicles tires and transmit tire pressure readings
Check the tires inflation pressure when the tires to a receiver located in the vehicle.
are cold. Cold means your vehicle has been sitting
for at least three hours or driven no more than Each tire, including the spare (if provided), should be
1 mile (1.6 km). checked monthly when cold and inflated to the inflation
pressure recommended by the vehicle manufacturer
Remove the valve cap from the tire valve stem. Press on the vehicle placard or tire inflation pressure label.
the tire gage firmly onto the valve to get a pressure (If your vehicle has tires of a different size than the size
measurement. If the cold tire inflation pressure matches indicated on the vehicle placard or tire inflation
the recommended pressure on the Tire and Loading pressure label, you should determine the proper tire
Information label, no further adjustment is necessary. inflation pressure for those tires.)
If the inflation pressure is low, add air until you reach the
recommended amount. As an added safety feature, your vehicle has been
equipped with a tire pressure monitoring system (TPMS)
If you overfill the tire, release air by pushing on the that illuminates a low tire pressure telltale when one
metal stem in the center of the tire valve. Re-check the or more of your tires is significantly under-inflated.
tire pressure with the tire gage.
Accordingly, when the low tire pressure telltale
Be sure to put the valve caps back on the valve stems. illuminates, you should stop and check your tires as
They help prevent leaks by keeping out dirt and soon as possible, and inflate them to the proper
moisture. pressure. Driving on a significantly under-inflated tire
causes the tire to overheat and can lead to tire failure.
Under-inflation also reduces fuel efficiency and tire
tread life, and may affect the vehicles handling
and stopping ability.
5-57
Please note that the TPMS is not a substitute for proper Federal Communications Commission
tire maintenance, and it is the drivers responsibility to
maintain correct tire pressure, even if under-inflation has (FCC) and Industry and Science
not reached the level to trigger illumination of the Canada
TPMS low tire pressure telltale.
The Tire Pressure Monitor System (TPMS) operates on
Your vehicle has also been equipped with a TPMS a radio frequency and complies with Part 15 of the
malfunction indicator to indicate when the system is FCC Rules. Operation is subject to the following
not operating properly. The TPMS malfunction two conditions:
indicator is combined with the low tire pressure telltale.
When the system detects a malfunction, the telltale 1. This device may not cause harmful interference.
will flash for approximately one minute and then remain 2. This device must accept any interference received,
continuously illuminated. This sequence will continue including interference that may cause undesired
upon subsequent vehicle start-ups as long as the operation.
malfunction exists.
The Tire Pressure Monitor System (TPMS) operates
When the malfunction indicator is illuminated, the on a radio frequency and complies with RSS-210
system may not be able to detect or signal low tire of Industry and Science Canada. Operation is subject to
pressure as intended. TPMS malfunctions may occur for the following two conditions:
a variety of reasons, including the installation of 1. This device may not cause interference.
replacement or alternate tires or wheels on the vehicle
that prevent the TPMS from functioning properly. 2. This device must accept any interference received,
Always check the TPMS malfunction telltale after including interference that may cause undesired
replacing one or more tires or wheels on your vehicle to operation of the device.
ensure that the replacement or alternate tires and Changes or modifications to this system by other than
wheels allow the TPMS to continue to function properly. an authorized service facility could void authorization to
See Tire Pressure Monitor Operation on page 5-59, use this equipment.
5-58
Tire Pressure Monitor Operation The low tire pressure warning light comes on at each
ignition cycle until the tires are inflated to the correct
The Tire Pressure Monitor System (TPMS) is designed inflation pressure.
to warn the driver when a low tire pressure condition The tire pressure warning light may come on in cool
exists. If your vehicle has this feature, the TPMS weather when the vehicle is first started, and then turn
sensors are mounted onto each tire and wheel off as you start to drive. This could be an early
assembly, excluding the spare tire and wheel assembly. indicator that the tire pressures are getting low and
The TPMS sensors monitor the air pressure in your need to be inflated to the proper pressure.
vehicles tires and transmit tire pressure readings to a
receiver located in the vehicle. A Tire and Loading Information label, attached to your
vehicle, shows the size of your vehicles original
When a low tire pressure equipment tires and the correct inflation pressure for
condition is detected, the your vehicles tires when they are cold. See Loading
TPMS illuminates the Your Vehicle on page 4-18, for an example of the
low tire pressure warning tire information label and its location on your vehicle.
light on the instrument Also see Inflation - Tire Pressure on page 5-56.
panel cluster. Your vehicles TPMS system can warn you about a low
tire pressure condition but it does not replace normal
tire maintenance. See Tire Inspection and Rotation
on page 5-60 and Tires on page 5-49.
Notice: Liquid tire sealants could damage the
Tire Pressure Monitor System (TPMS) sensors.
Sensor damage caused by using a tire sealant is
not covered by your warranty. Do not use liquid
tire sealants.
5-59
TPMS Malfunction Light If the TPMS is not functioning it cannot detect or signal
a low tire condition. See your dealer/retailer for
The TPMS will not function properly if one or more of service if the TPMS malfunction light and DIC message
the TPMS sensors are missing or inoperable. When the comes on and stays on.
system detects a malfunction, the low tire warning
light flashes for about one minute and then stays on for TPMS Sensor Identification Codes
the remainder of the ignition cycle. The low tire
warning light comes on at each ignition cycle until the Each TPMS sensor has a unique identification code.
problem is corrected. Some of the conditions that Any time you replace one or more of the TPMS sensors,
can cause the malfunction light to come on are: or rotate the vehicles tires, the identification codes
need to be matched to the new tire/wheel position. The
One of the road tires has been replaced with the sensors are matched, to the tire/wheel positions, in
spare tire. The spare tire does not have a TPMS the following order: driver side front tire, passenger side
sensor. The TPMS malfunction light and DIC front tire, passenger side rear tire, and driver side
message should go off once you re-install the road rear tire using a TPMS diagnostic tool. See your
tire containing the TPMS sensor. dealer/retailer for service.
One or more TPMS sensors are missing or
damaged. The TPMS malfunction light should go off Tire Inspection and Rotation
when the TPMS sensors are installed and the
sensor matching process is performed successfully. We recommend that you regularly inspect your
See your dealer/retailer for service. vehicles tires, including the spare tire, for signs of
Replacement tires or wheels do not match your wear or damage. See When It Is Time for New
Tires on page 5-62 for more information.
vehicles original equipment tires or wheels. Tires
and wheels other than those recommended for your Tires should be rotated every 5,000 to 8,000 miles
vehicle could prevent the TPMS from functioning (8 000 to 13 000 km). See Part A: Scheduled
properly. See Buying New Tires on page 5-62. Maintenance Services on page 6-4.
Operating electronic devices or being near facilities
using radio wave frequencies similar to the TPMS
could cause the TPMS sensors to malfunction.
5-60
The purpose of a regular tire rotation is to achieve After the tires have been rotated, adjust the front
a uniform wear for all tires on the vehicle. This and rear inflation pressures as shown on the
will ensure that your vehicle continues to perform tire and loading information label. See Loading
most like it did when the tires were new. Your Vehicle on page 4-18 for an example of the
Any time you notice unusual wear, rotate your tire and loading information label and where it
tires as soon as possible and check wheel is located on your vehicle. Make certain that
alignment. Also check for damaged tires or wheels. all wheel nuts are properly tightened. See Wheel
See When It Is Time for New Tires on page 5-62 Nut Torque under Capacities and Specifications
and Wheel Replacement on page 5-66 for on page 5-94.
more information.
{CAUTION:
Rust or dirt on a wheel, or on the parts to
which it is fastened, can make wheel nuts
become loose after time. The wheel could
come off and cause an accident. When
you change a wheel, remove any rust or
dirt from places where the wheel attaches
to the vehicle. In an emergency, you can
use a cloth or a paper towel to do this;
but be sure to use a scraper or wire brush
later, if needed, to get all the rust or dirt
When rotating your tires, always use the correct off. See Changing a Flat Tire on page 5-69.
rotation pattern shown here.
Do not include the compact spare tire in the tire
rotation.
5-61
When It Is Time for New Tires The tire has a bump, bulge, or split.
Various factors, such as maintenance, temperatures, The tire has a puncture, cut, or other damage that
driving speeds, vehicle loading, and road conditions cannot be repaired well because of the size or
influence when you need new tires. location of the damage.
One way to tell when it is The rubber in tires degrades over time, even if they are
time for new tires is to not being used. This is also true for the spare tire, if
check the treadwear your vehicle has one. Multiple conditions affect how fast
indicators, which will this aging takes place, including temperatures, loading
appear when your tires conditions, and inflation pressure maintenance. With
have only 1/16 inch proper care and maintenance tires will typically wear out
(1.6 mm) or less of tread before they degrade due to age. If you are unsure
remaining. about the need to replace your tires as they get older,
consult the tire manufacturer for more information.
Buying New Tires

GM has developed and matched specific tires for your
vehicle. If you need replacement tires, GM strongly
recommends that you get tires that are the same size,
You need new tires if any of the following statements brand, load range, speed rating, and construction
are true: type (radial and bias-belted tires) as your vehicles
You can see the indicators at three or more places original tires. This way, your vehicle will continue to have
around the tire. tires that are designed to give the same performance
and vehicle safety, during normal use, as the original
You can see cord or fabric showing through the tires. See Tire Sidewall Labeling on page 5-50 for
tires rubber. additional information.
The tread or sidewall is cracked, cut, or snagged
deep enough to show cord or fabric.
5-62
GM recommends replacing tires in sets of four. This is
because uniform tread depth on all tires will help
keep your vehicle performing most like it did when the {CAUTION:
tires were new. Replacing less than a full set of tires can
affect the braking and handling performance of your If you use bias-ply tires on your vehicle,
vehicle. See Tire Inspection and Rotation on page 5-60. the wheel rim flanges could develop
cracks after many miles of driving. A tire
and/or wheel could fail suddenly, causing
{CAUTION: a crash. Use only radial-ply tires with the
wheels on your vehicle.
Mixing tires could cause you to lose
control while driving. If you mix tires of Your vehicles original equipment tires are listed on the
different sizes, brands, or types (radial Tire and Loading Information Label. See Loading
and bias-belted tires), the vehicle may not Your Vehicle on page 4-18, for more information about
handle properly, and you could have a the Tire and Loading Information label and its location
crash. Using tires of different sizes, on your vehicle.
brands, or types may also cause damage
to your vehicle. Be sure to use the correct
size, brand, and type of tires on all
wheels. It is all right to drive with your
compact spare temporarily, as it was
developed for use on your vehicle.
See Compact Spare Tire on page 5-78.
5-63
Different Size Tires and Wheels Uniform Tire Quality Grading
If you add wheels or tires that are a different size than Quality grades can be found where applicable on
your original equipment wheels and tires, this may the tire sidewall between tread shoulder and
affect the way your vehicle performs, including its maximum selection width. For example:
braking, ride and handling characteristics, stability, and
resistance to rollover. Additionally, if your vehicle Treadwear 200 Traction AA Temperature A
has electronic systems such as, anti-lock brakes, The following information relates to the system
traction control, and electronic stability control, the developed by the Unites States National Highway
performance of these systems can be affected. Traffic Safety Administration (NHTSA), which
grades tires by treadwear, traction, and
temperature performance. This applies only to
{CAUTION: vehicles sold in the United States. The grades are
molded on the sidewalls of most passenger car
tires. The Uniform Tire Quality Grading (UTQG)
If you add different sized wheels, your vehicle system does not apply to deep tread, winter-type
may not provide an acceptable level of snow tires, space-saver, or temporary use
performance and safety if tires not spare tires, tires with nominal rim diameters of
recommended for those wheels are selected. 10 to 12 inches (25 to 30 cm), or to some
You may increase the chance that you will limited-production tires.
crash and suffer serious injury. Only use GM While the tires available on General Motors
specific wheel and tire systems developed for passenger cars and light trucks may vary with
your vehicle, and have them properly installed respect to these grades, they must also conform
by a GM certified technician. to federal safety requirements.
See Buying New Tires on page 5-62 and Accessories

and Modifications on page 5-4 for additional information.
5-64
Treadwear Temperature A, B, C
The treadwear grade is a comparative rating The temperature grades are A (the highest), B,
based on the wear rate of the tire when tested and C, representing the tires resistance to
under controlled conditions on a specified the generation of heat and its ability to dissipate
government test course. For example, a tire heat when tested under controlled conditions on a
graded 150 would wear one and a half (112) times specified indoor laboratory test wheel. Sustained
as well on the government course as a tire high temperature can cause the material of the tire
graded 100. The relative performance of tires to degenerate and reduce tire life, and excessive
depends upon the actual conditions of their use, temperature can lead to sudden tire failure.
however, and may depart significantly from The grade C corresponds to a level of performance
the norm due to variations in driving habits, service which all passenger car tires must meet under
practices, and differences in road characteristics the Federal Motor Vehicle Safety Standard
and climate. No. 109. Grades B and A represent higher levels
of performance on the laboratory test wheel
Traction AA, A, B, C than the minimum required by law.
The traction grades, from highest to lowest, are
AA, A, B, and C. Those grades represent the tires Warning: The temperature grade for this tire
ability to stop on wet pavement as measured is established for a tire that is properly inflated
under controlled conditions on specified and not overloaded. Excessive speed,
government test surfaces of asphalt and concrete. under-inflation, or excessive loading, either
A tire marked C may have poor traction separately or in combination, can cause
performance. heat buildup and possible tire failure.
Warning: The traction grade assigned to this

tire is based on straight-ahead braking
traction tests, and does not include
acceleration, cornering, hydroplaning, or peak
traction characteristics.
5-65
Wheel Alignment and Tire Balance If you need to replace any of your wheels, wheel bolts,
wheel nuts, or Tire Pressure Monitor System (TPMS)
The tires and wheels on your vehicle were aligned sensors, replace them only with new GM original
and balanced carefully at the factory to give you the equipment parts. This way, you will be sure to have the
longest tire life and best overall performance. right wheel, wheel bolts, wheel nuts, and TPMS
Adjustments to wheel alignment and tire balancing will sensors for your vehicle.
not be necessary on a regular basis. However, if
you notice unusual tire wear or your vehicle pulling to
one side or the other, the alignment might need to
be checked. If you notice your vehicle vibrating when
{CAUTION:
driving on a smooth road, the tires and wheels
might need to be rebalanced. See your dealer/retailer Using the wrong replacement wheels, wheel
for proper diagnosis. bolts, or wheel nuts on your vehicle can be
dangerous. It could affect the braking and
Wheel Replacement handling of your vehicle, make your tires lose
air and make you lose control. You could have
Replace any wheel that is bent, cracked, or badly rusted a collision in which you or others could be
or corroded. If wheel nuts keep coming loose, the injured. Always use the correct wheel, wheel
wheel, wheel bolts, and wheel nuts should be replaced. bolts, and wheel nuts for replacement.
If the wheel leaks air, replace it (except some
aluminum wheels, which can sometimes be repaired).
See your dealer/retailer if any of these conditions exist. Notice: The wrong wheel can also cause problems
Your dealer/retailer will know the kind of wheel you need. with bearing life, brake cooling, speedometer or
odometer calibration, headlamp aim, bumper height,
Each new wheel should have the same load-carrying vehicle ground clearance, and tire or tire chain
capacity, diameter, width, offset, and be mounted clearance to the body and chassis.
the same way as the one it replaces.
See Changing a Flat Tire on page 5-69 for more
information.
5-66
Used Replacement Wheels Tire Chains
Notice: Use tire chains only where legal and only
when you must. Use only SAE Class S type chains
{CAUTION: that are the proper size for your tires. Install them
on the front tires and tighten them as tightly as
Putting a used wheel on your vehicle is possible with the ends securely fastened. Drive
dangerous. You cannot know how it has been slowly and follow the chain manufacturers
used or how far it has been driven. It could fail instructions. If you can hear the chains contacting
suddenly and cause a crash. If you have to your vehicle, stop and retighten them. If the contact
replace a wheel, use a new GM original continues, slow down until it stops. Driving too
fast or spinning the wheels with chains on will
equipment wheel.
damage your vehicle.
5-67
If a Tire Goes Flat
It is unusual for a tire to blowout while you are driving, {CAUTION:
especially if you maintain your vehicles tires properly.
If air goes out of a tire, it is much more likely to leak out Lifting a vehicle and getting under it to do
slowly. But if you should ever have a blowout, here maintenance or repairs is dangerous without
are a few tips about what to expect and what to do: the appropriate safety equipment and training.
If a front tire fails, the flat tire creates a drag that pulls The jack provided with your vehicle is
the vehicle toward that side. Take your foot off the designed only for changing a flat tire. If it is
accelerator pedal and grip the steering wheel firmly. used for anything else, you or others could be
Steer to maintain lane position, and then gently brake to badly injured or killed if the vehicle slips off
a stop well out of the traffic lane.
the jack. Use the jack provided with your
A rear blowout, particularly on a curve, acts much like a vehicle only for changing a flat tire.
skid and may require the same correction you would
use in a skid. In any rear blowout remove your foot from
the accelerator pedal. Get the vehicle under control If a tire goes flat, the next part shows how to use the
by steering the way you want the vehicle to go. It may jacking equipment to change a flat tire safely.
be very bumpy and noisy, but you can still steer. Gently
brake to a stop, well off the road if possible.
5-68
Changing a Flat Tire
If a tire goes flat, avoid further tire and wheel damage
by driving slowly to a level place. Turn on the hazard
warning flashers. See Hazard Warning Flashers To be certain the vehicle will not move, put
on page 3-6 for more information. blocks at the front and rear of the tire farthest
away from the one being changed. That would
be the tire on the other side, at the opposite
{CAUTION: end of the vehicle.
Changing a tire can be dangerous. The vehicle When you have a flat tire, use the following example as a
can slip off the jack and roll over or fall on you guide to assist you in the placement of wheel blocks.
or other people. You and they could be badly
injured or even killed. Find a level place to
change your tire. To help prevent the vehicle
from moving:
1. Set the parking brake firmly.
2. Put an automatic transmission shift lever in
PARK (P), or shift a manual transmission to
FIRST (1) or REVERSE (R).
3. Turn off the engine and do not restart while
the vehicle is raised.
4. Do not allow passengers to remain in the
vehicle.
The following information tells you how to use the jack
CAUTION: (Continued) and change a tire.
5-69
Removing the Spare Tire and Tools Wagon Models
The tools you will be using to change a flat tire are To access the spare tire and tools:
shown below. Refer to your vehicle model to access the 1. Open the liftgate. See Liftgate on page 2-10 for
spare tire and tools. more information.
2. Fold the floor cover by pulling the handle upward.
3. Lift the floor tray.
A. Jack C. Jack Handle

B. Wheel Wrench D. Screwdriver
4. Release the prop from its retainer and put the prop
into the slot.
5-70
5. Turn the retainer on the compact spare tire 7. To access the tools, pull the strap on the tool box
counterclockwise and remove the retainer. cover upward. The tools are located inside the
6. Remove the compact spare tire. See Compact foam tray.
Spare Tire on page 5-78 for more information.
5-71
Hatchback Models
To access the spare tire and tools:
1. Open the liftgate. See Liftgate on page 2-10 for
more information.
2. Remove the trim cover by pulling up on the tab.
3. Remove the foam tray that contains the tools.
6. Remove the jack by turning the jack retainer,

located on the right side of the jack,
counterclockwise to release it. The jack is located in
the trunk, in front of the compact spare tire.
7. Then remove the jack handle and the wheel
wrench. The jack handle and the wheel wrench are
located inside the foam tray.
4. Turn the retainer on the compact spare tire

counterclockwise and remove the retainer.
5. Remove the compact spare tire. See Compact
Spare Tire on page 5-78 for more information.
5-72
Removing the Flat Tire and
Installing the Spare Tire
1. Do a safety check before proceeding. See Changing
a Flat Tire on page 5-69 for more information.
2. If your vehicle has wheel covers, use the jack
handle to begin loosening the wheel covers.
Using the flat end of the jack handle or the
screwdriver, pry along the edge of the wheel cover
until it comes off.
Store the wheel cover in the cargo area until you
have the flat tire repaired or replaced.
3. Use the wheel wrench to loosen all the wheel nuts.

Do not remove them yet.
5-73
4. Locate the notch near each wheel in the frame 6. Insert the jack handle into the jack and the wheel
which the jack head fits in. wrench onto the end of the jack handle.
Position the jack and raise the jack head until it fits
firmly into the notch in the vehicles frame nearest
the flat tire.
5. Put the compact spare tire near you.
5-74
{CAUTION: 7. Raise the vehicle by turning the wheel wrench
clockwise. Raise the vehicle far enough off the
ground so there is enough room for the compact
Getting under a vehicle when it is jacked up is spare tire to fit underneath the wheel well.
dangerous. If the vehicle slips off the jack, you
8. Remove all of the wheel nuts by turning them
could be badly injured or killed. Never get under counterclockwise.
a vehicle when it is supported only by a jack.
9. Remove the flat tire.
{CAUTION:
Raising your vehicle with the jack improperly
positioned can damage the vehicle and even
make the vehicle fall. To help avoid personal
injury and vehicle damage, be sure to fit the
jack lift head into the proper location before
raising the vehicle.
5-75
10. Remove any rust or dirt
from the wheel bolts,
{CAUTION: mounting surfaces
and spare wheel.
Rust or dirt on a wheel, or on the parts to
which it is fastened, can make wheel nuts
become loose after time. The wheel could
come off and cause an accident. When you
change a wheel, remove any rust or dirt from
places where the wheel attaches to the vehicle.
In an emergency, you can use a cloth or a
paper towel to do this; but be sure to use a
scraper or wire brush later, if needed, to get all 11. Place the compact spare tire on the wheel-mounting
surface.
the rust or dirt off. See Changing a Flat Tire on
page 5-69.
{CAUTION:
Never use oil or grease on studs or nuts.
Because the nuts might come loose. The
vehicles wheel could fall off, causing a crash.
5-76
12. Install the wheel nuts with the rounded end of the Notice: Improperly tightened wheel nuts can lead
nuts toward the wheel. Tighten each nut by hand to brake pulsation and rotor damage. To avoid
clockwise until the wheel is held against the hub. expensive brake repairs, evenly tighten the wheel
13. Lower the vehicle by turning the wheel wrench nuts in the proper sequence and to the proper
counterclockwise. Lower the jack completely. torque specification. See Capacities and
Specifications on page 5-94 for the wheel nut torque
specification.
{CAUTION: 14. Tighten the wheel nuts
firmly in a crisscross
Incorrect or improperly tightened wheel nuts sequence, as shown.
can cause the wheel to come loose and even
come off. This could lead to a crash. If you
have to replace them, be sure to get new
original equipment wheel nuts. Stop
somewhere as soon as you can and have the
nuts tightened with a torque wrench to the
proper torque specification. See Capacities
and Specifications on page 5-94 for wheel nut
torque specification. Notice: Wheel covers will not fit on your vehicles
compact spare. If you try to put a wheel cover
on the compact spare, the cover or the spare could
be damaged.
5-77
Storing a Flat or Spare Tire Compact Spare Tire
and Tools Although the compact spare tire was fully inflated when
your vehicle was new, it can lose air after a time.
Check the inflation pressure regularly. It should be
{CAUTION: 60 psi (420 kPa).
After installing the compact spare on your vehicle, you
should stop as soon as possible and make sure
Storing a jack, a tire, or other equipment in the your spare tire is correctly inflated. The compact spare
passenger compartment of the vehicle could is made to perform well at speeds up to 50 mph
cause injury. In a sudden stop or collision, (80 km/h), so you can finish your trip and have your
loose equipment could strike someone. Store full-size tire repaired or replaced where you want.
all these in the proper place. Of course, it is best to replace your spare with a full-size
tire as soon as you can. Your spare will last longer
and be in good shape in case you need it again.
To store a flat or compact spare tire and tools:
Notice: When the compact spare is installed, do
1. Store the flat tire or the compact spare in the not take your vehicle through an automatic car wash
compact spare tire compartment. with guide rails. The compact spare can get
2. Secure the retainer. caught on the rails. That can damage the tire and
wheel, and maybe other parts of your vehicle.
3. Store the tools securely in the foam tray and place
the tray back in the cargo area. Do not use your compact spare on other vehicles.
4. Replace the trim cover. And do not mix your compact spare tire or wheel with
other wheels or tires. They will not fit. Keep your
The compact spare tire is for temporary use only. spare tire and its wheel together.
Replace the compact spare tire with a full-size tire as
soon as you can. See Compact Spare Tire on Notice: Tire chains will not fit your compact spare.
page 5-78. Using them can damage your vehicle and can
damage the chains too. Do not use tire chains on
your compact spare.
5-78
Appearance Care Notice: If you use abrasive cleaners when cleaning
glass surfaces on your vehicle, you could scratch
the glass and/or cause damage to the rear window
Interior Cleaning defogger. When cleaning the glass on your
vehicle, use only a soft cloth and glass cleaner.
Your vehicles interior will continue to look its best if it is
Many cleaners contain solvents that may become
cleaned often. Although not always visible, dust and
concentrated in your vehicles breathing space. Before
dirt can accumulate on your upholstery. Dirt can damage
using cleaners, read and adhere to all safety
carpet, fabric, leather, and plastic surfaces. Regular
instructions on the label. While cleaning your vehicles
vacuuming is recommended to remove particles
interior, maintain adequate ventilation by opening
from your upholstery. It is important to keep your
your vehicles doors and windows.
upholstery from becoming and remaining heavily soiled.
Soils should be removed as quickly as possible. Your Dust may be removed from small buttons and knobs
vehicles interior may experience extremes of heat using a small brush with soft bristles.
that could cause stains to set rapidly. Your dealer/retailer has a product for cleaning your
Lighter colored interiors may require more frequent vehicles glass. Should it become necessary, you can
cleaning. Use care because newspapers and garments also obtain a product from your dealer/retailer to remove
that transfer color to your home furnishings may also odors from your vehicles upholstery.
transfer color to your vehicles interior. Do not clean your vehicle using the following cleaners
When cleaning your vehicles interior, only use cleaners or techniques:
specifically designed for the surfaces being cleaned. Never use a knife or any other sharp object to
Permanent damage may result from using cleaners on
remove a soil from any interior surface.
surfaces for which they were not intended. Use
glass cleaner only on glass. Remove any accidental Never use a stiff brush. It can cause damage to
over-spray from other surfaces immediately. To prevent your vehicles interior surfaces.
over-spray, apply cleaner directly to the cleaning Never apply heavy pressure or rub aggressively
cloth.
with a cleaning cloth. Use of heavy pressure
can damage your interior and does not improve the
effectiveness of soil removal.
5-79
Use only mild, neutral-pH soaps. Avoid laundry To clean, use the following instructions:
detergents or dishwashing soaps with degreasers. 1. Saturate a lint-free, clean white cloth with water or
Using too much soap will leave a residue that club soda.
leaves streaks and attracts dirt. For liquid cleaners,
about 20 drops per gallon (3.78 L) of water is a 2. Wring the cloth to remove excess moisture.
good guide. 3. Start on the outside edge of the soil and gently rub
Do not heavily saturate your upholstery while toward the center. Continue cleaning, using a clean
area of the cloth each time it becomes soiled.
cleaning.
4. Continue to gently rub the soiled area until the
Damage to your vehicles interior may result from cleaning cloth remains clean.
the use of many organic solvents such as naptha,
alcohol, etc. 5. If the soil is not completely removed, use a mild
soap solution and repeat the cleaning process
that was used with plain water.
Fabric/Carpet
If any of the soil remains, a commercial fabric cleaner or
Use a vacuum cleaner with a soft brush attachment spot lifter may be necessary. When a commercial
frequently to remove dust and loose dirt. A canister upholstery cleaner or spot lifter is to be used, test a
vacuum with a beater bar in the nozzle may only small hidden area for colorfastness first. If the locally
be used on floor carpet and carpeted floor mats. For cleaned area gives any impression that a ring formation
soils, always try to remove them first with plain water or may result, clean the entire surface.
club soda. Before cleaning, gently remove as much
After the cleaning process has been completed, a paper
of the soil as possible using one of the following
towel can be used to blot excess moisture from the
techniques:
fabric or carpet.
For liquids: gently blot the remaining soil with a
paper towel. Allow the soil to absorb into the
paper towel until no more can be removed.
For solid dry soils: remove as much as possible
and then vacuum.
5-80
Leather or wax-based products, or those containing organic
solvents to clean your vehicles interior because
A soft cloth dampened with water can be used to they can alter the appearance by increasing the gloss in
remove dust. If a more thorough cleaning is necessary, a non-uniform manner.
a soft cloth dampened with a mild soap solution can Some commercial products may increase gloss on your
be used. Allow the leather to dry naturally. Do not use instrument panel. The increase in gloss may cause
heat to dry. Never use steam to clean leather. Never annoying reflections in the windshield and even make it
use spot lifters or spot removers on leather. Many difficult to see through the windshield under certain
commercial leather cleaners and coatings that are sold conditions.
to preserve and protect leather may permanently
change the appearance and feel of your leather and are
not recommended. Do not use silicone or wax-based Care of Safety Belts
products, or those containing organic solvents to clean
your vehicles interior because they can alter the Keep belts clean and dry.
appearance by increasing the gloss in a non-uniform
manner. Never use shoe polish on leather.
{CAUTION:
Instrument Panel, Vinyl, and Other
Do not bleach or dye safety belts. If you do, it
Plastic Surfaces may severely weaken them. In a crash, they
A soft cloth dampened with water may be used to might not be able to provide adequate
remove dust. If a more thorough cleaning is necessary, protection. Clean safety belts only with mild
a clean soft cloth dampened with a mild soap solution soap and lukewarm water.
can be used to gently remove dust and dirt. Never use
spot lifters or removers on plastic surfaces. Many
commercial cleaners and coatings that are sold to
preserve and protect soft plastic surfaces may
permanently change the appearance and feel of your
interior and are not recommended. Do not use silicone
5-81
Weatherstrips Rinse the vehicle well, before washing and after to
remove all cleaning agents completely. If they are
Silicone grease on weatherstrips will make them last allowed to dry on the surface, they could stain.
longer, seal better, and not stick or squeak. Apply Dry the finish with a soft, clean chamois or an all-cotton
silicone grease with a clean cloth. During very cold, towel to avoid surface scratches and water spotting
damp weather frequent application may be required.
High pressure car washes may cause water to enter the
vehicle. Avoid using high pressure washes closer
Washing Your Vehicle than 12 inches (30 cm) to the surface of the vehicle.
The best way to preserve your vehicles finish is to keep Use of power washers exceeding 1,200 psi (8 274 kPa)
it clean by washing it often. can result in damage or removal of paint and decals.
Notice: Certain cleaners contain chemicals that can

damage the emblems or nameplates on your
Cleaning Exterior Lamps/Lenses
vehicle. Check the cleaning product label. If it states Use only lukewarm or cold water, a soft cloth and a car
that it should not be used on plastic parts, do not washing soap to clean exterior lamps and lenses.
use it on your vehicle or damage may occur Follow instructions under Washing Your Vehicle on
and it would not be covered by the warranty. page 5-82.
Do not wash the vehicle in direct sunlight. Use a car
washing soap. Do not use cleaning agents that Finish Care
are petroleum based or that contain acid or abrasives,
as they can damage the paint, metal or plastic on Occasional waxing or mild polishing of your vehicle by
your vehicle. Approved cleaning products can be hand may be necessary to remove residue from the
obtained from your dealer/retailer. See Vehicle paint finish. You can get approved cleaning products
Care/Appearance Materials on page 5-86. Follow all from your dealer/retailer. See Vehicle Care/Appearance
manufacturers directions regarding correct product Materials on page 5-86.
usage, necessary safety precautions and appropriate
disposal of any vehicle care product.
5-82
If your vehicle has a basecoat/clearcoat paint finish, the Protecting Exterior Bright Metal Parts
clearcoat gives more depth and gloss to the colored
basecoat. Always use waxes and polishes that are Bright metal parts should be cleaned regularly to keep
non-abrasive and made for a basecoat/clearcoat paint their luster. Washing with water is all that is usually
finish. needed. However, you may use chrome polish on
chrome or stainless steel trim, if necessary.
Notice: Machine compounding or aggressive
Use special care with aluminum trim. To avoid damaging
polishing on a basecoat/clearcoat paint finish may
protective trim, never use auto or chrome polish,
damage it. Use only non-abrasive waxes and
steam or caustic soap to clean aluminum. A coating of
polishes that are made for a basecoat/clearcoat
wax, rubbed to high polish, is recommended for all
paint finish on your vehicle.
bright metal parts.
Foreign materials such as calcium chloride and other
salts, ice melting agents, road oil and tar, tree sap, bird
droppings, chemicals from industrial chimneys, etc.,
Windshield and Wiper Blades
can damage your vehicles finish if they remain Clean the outside of the windshield with glass cleaner.
on painted surfaces. Wash the vehicle as soon as
possible. If necessary, use non-abrasive cleaners that Clean the rubber blades using a lint free cloth or
are marked safe for painted surfaces to remove paper towel soaked with windshield washer fluid or a
foreign matter. mild detergent. Wash the windshield thoroughly
when cleaning the blades. Bugs, road grime, sap, and a
Exterior painted surfaces are subject to aging, weather buildup of vehicle wash/wax treatments may cause
and chemical fallout that can take their toll over a wiper streaking. Replace the wiper blades if they are
period of years. You can help to keep the paint finish worn or damaged.
looking new by keeping your vehicle garaged or covered
whenever possible. Wipers can be damaged by:
Extreme dusty conditions
Sand and salt
Heat and sun
Snow and ice, without proper removal
5-83
Aluminum Wheels Notice: If you drive your vehicle through an
automatic car wash that has silicone carbide tire
Notice: If you use strong soaps, chemicals, cleaning brushes, you could damage the aluminum
abrasive polishes, cleaners, brushes, or cleaners or chrome-plated wheels. The repairs would not
that contain acid on aluminum or chrome-plated be covered by your warranty. Never drive a vehicle
wheels, you could damage the surface of the equipped with aluminum or chrome-plated wheels
wheel(s). The repairs would not be covered by your through an automatic car wash that uses silicone
warranty. Use only approved cleaners on aluminum carbide tire cleaning brushes.
or chrome-plated wheels.
Keep the wheels clean using a soft clean cloth with mild Tires
soap and water. Rinse with clean water. After rinsing
thoroughly, dry with a soft clean towel. A wax may then To clean the tires, use a stiff brush with tire cleaner.
be applied. Notice: Using petroleum-based tire dressing
Notice: Using chrome polish on aluminum wheels products on your vehicle may damage the paint
could damage the wheels. The repairs would not finish and/or tires. When applying a tire dressing,
be covered by your warranty. Use chrome polish on always wipe off any overspray from all painted
chrome wheels only. surfaces on your vehicle.
The surface of these wheels is similar to the painted

surface of the vehicle. Do not use strong soaps, Sheet Metal Damage
chemicals, abrasive polishes, abrasive cleaners, If the vehicle is damaged and requires sheet metal
cleaners with acid, or abrasive cleaning brushes on repair or replacement, make sure the body repair shop
them because the surface could be damaged. Do not applies anti-corrosion material to parts repaired or
use chrome polish on aluminum wheels. replaced to restore corrosion protection.
Original manufacturer replacement parts will provide the
corrosion protection while maintaining the warranty.
5-84
Finish Damage At least every spring, flush these materials from the
underbody with plain water. Clean any areas where mud
Any stone chips, fractures or deep scratches in the and debris can collect. Dirt packed in close areas of
finish should be repaired right away. Bare metal the frame should be loosened before being flushed.
will corrode quickly and may develop into major repair Your dealer/retailer or an underbody car washing system
expense. can do this for you.
Minor chips and scratches can be repaired with touch-up
materials available from your dealer/retailer. Larger Chemical Paint Spotting
areas of finish damage can be corrected in your
dealers/retailers body and paint shop. Some weather and atmospheric conditions can create a
chemical fallout. Airborne pollutants can fall upon and
attack painted surfaces on the vehicle. This damage can
Underbody Maintenance take two forms: blotchy, ring-shaped discolorations,
and small, irregular dark spots etched into the
Chemicals used for ice and snow removal and dust
paint surface.
control can collect on the underbody. If these are not
removed, corrosion and rust can develop on the Although no defect in the paint job causes this, we will
underbody parts such as fuel lines, frame, floor pan, repair, at no charge to the owner, the surfaces of
and exhaust system even though they have corrosion new vehicles damaged by this fallout condition within
protection. 12 months or 12,000 miles (20 000 km) of purchase,
whichever occurs first.
5-85
Vehicle Care/Appearance Materials Description Usage
Removes swirl marks, fine
Description Usage Swirl Remover Polish scratches and other light
surface contamination.
Polishing Cloth Interior and exterior
Wax-Treated polishing cloth. Cleaner Wax Removes light scratches
and protects finish.
Tar and Road Oil Removes tar, road oil and
Remover asphalt. Cleans, shines and
Foaming Tire Shine protects tires. No wiping
Chrome Cleaner and Use on chrome or Low Gloss
necessary.
Polish stainless steel.
Medium foaming
White Sidewall Tire Removes soil and black shampoo. Cleans and
Cleaner marks from whitewalls. Wash Wax Concentrate lightly waxes.
Vinyl Cleaner Cleans vinyl. Biodegradable and
Removes dirt, grime, phosphate free.
Glass Cleaner
smoke and fingerprints. Removes spots and stains
Removes dirt and grime Spot Lifter from carpets, vinyl and
Chrome and Wire Wheel cloth upholstery.
Cleaner from chrome wheels and
wire wheel covers. Odorless spray odor
Removes dust, Odor Eliminator eliminator used on fabrics,
fingerprints, and surface vinyl, leather and carpet.
Finish Enhancer
contaminants. Spray on
wipe off.
5-86
Vehicle Identification Engine Identification
The eighth character in your VIN is the engine code.
This code helps you identify your vehicles engine,
Vehicle Identification Number (VIN) specifications, and replacement parts. See Capacities
and Specifications on page 5-94 for your vehicles
engine code.
Service Parts Identification Label

This label is on the inside of the glove box. It is
very helpful if you ever need to order parts. The label
has the following information:
This is the legal identifier for your vehicle. It appears on Vehicle Identification Number (VIN)
a plate in the front corner of the instrument panel, on Model designation
the driver side. You can see it if you look through
the windshield from outside your vehicle. The VIN also Paint information
appears on the Vehicle Certification and Service Production options and special equipment
Parts labels and the certificates of title and registration.
Do not remove this label from the vehicle.
5-87
Electrical System Headlamp Wiring
The headlamp wiring is protected by fuses in the fuse
Add-On Electrical Equipment block. An electrical overload will cause the lamps to turn
off. If this happens, have your headlamp wiring
Notice: Do not add anything electrical to your checked right away.
vehicle unless you check with your dealer/retailer
first. Some electrical equipment can damage Windshield Wiper Fuses
your vehicle and the damage would not be covered
by your warranty. Some add-on electrical equipment The windshield wiper motor is protected by a circuit
can keep other components from working as they breaker and a fuse. If the motor overheats due to heavy
should. snow, etc., the wiper will stop until the motor cools. If
Add-on equipment can drain your vehicles battery, even the overload is caused by some electrical problem, have
if your vehicle is not operating. it fixed.
Your vehicle has an airbag system. Before attempting to
add anything electrical to your vehicle, see Servicing Power Windows and Other Power
Your Airbag-Equipped Vehicle on page 1-64. Options
Circuit breakers in the fuse block protect the power
windows and other power accessories. When the current
load is too heavy, the circuit breaker opens and
closes, protecting the circuit until the problem is fixed or
goes away.
5-88
Fuses and Circuit Breakers Instrument Panel Fuse Block
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses, circuit breakers
and fusible thermal links. This greatly reduces the
chance of fires caused by electrical problems.
Look at the silver-colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical
size and rating.
If you ever have a problem on the road and dont have
a spare fuse, you can borrow one that has the same
amperage. Just pick some feature of your vehicle
that you can get along without like the radio or
cigarette lighter and use its fuse, if it is the correct
amperage. Replace it as soon as you can.
The instrument panel fuse block is located on the end of

the instrument panel, on the driver side of the vehicle.
To access the fuses, open the fuse panel door by pulling
it out.
To reinstall the door, insert the tabs at the back end
first, then push the door into the instrument panel
to secure it.
5-89
Fuses Usage
AIRBAG Airbag
WPR Wiper
RADIO/CLK Radio/Clock
ECM Engine Control Module
AIRBAG Airbag
AUX LTR Extra Jack
TRN SIG Turn Signal Lamps
LAMPS
ABS Antilock Brake System
LTR Cigarette Lighter
Cluster, Brake Transmission Shift
CLSTR, BTSI Interlock/Automatic Transmission
Shift Lock (BTSI) Solenoid
RKE Remote Keyless Entry
BCK/UP Back-up
BLANK Not Used
TCM Transmission Control Module
BATT SAVER Battery Saver
ENG FUSE Engine Fuse Box, Daytime Running
BOX DRL Lamps
5-90
Fuses Usage Engine Compartment Fuse Block
HAZRD LAMPS Hazard Lamps
A/C, CLK Air Conditioning Switch, Clock
HVAC Heating, Ventilation and Air
Conditioning
RKE Remote Keyless Entry
RADIO Radio
S/ROOF Sunroof
DLC Data Link Connector
IMMOBILIZER Immobilizer
The engine compartment fuse block is located on the

driver side of the vehicle, near the battery. See Engine
Compartment Overview on page 5-12 for more
information on location. To access the fuses, press in
the top flap to release the cover.
To reinstall the cover, push the cover until it is secure.
Notice: Spilling liquid on any electrical components
on your vehicle may damage it. Always keep the
covers on any electrical component.
5-91
Fuses Usage Fuses Usage
HEAD LAMPS Headlamps A/C Air Conditioning
ECM Engine Control Module HORN Horn
I/P FUSE Instrument Panel Fuse HI BEAM Headlamp High-Beam
FUEL PUMP Fuel Pump DRIVERS Driver Power Window
PWR WNDW
5-92
Fuses Usage Fuses Usage
STOP LAMPS Stoplamps IGN 1 Ignition 1
DR/LCK Door Lock FUSE PLR Fuse Puller
MIR HTD Heated Mirror COOL Cooling Fan Low
FRT FOG Front Fog FAN LOW
License Plate Lamp, Parking DEFOG Defog
ILLUM LT
Lamp Left COOL FAN HI Cooling Fan High
INJ Injector PWR WNDW Power Window
Evaporative Emission (EVAP)
ENG SNSR Canister Purge Solenoid, Heated Relays Usage
Oxygen Sensor (HO2S), Cooling
Fan Relay, CMP Sensor COOL Cooling Fan Low
FAN LOW
LOW BEAM LT Headlamp Low-Beam Left
FRT FOG Front Fog
Illumination Circuit, Parking
ILLUM RT ILLUM Illumination Relay
Lamp Right
LOW BEAM RT Headlamp Low-Beam Right A/C CMPRSR Air Conditioning Compressor
SPARE Spare HORN Horn
SPARE Spare DEFOG Defog
SPARE Spare FUEL PUMP Fuel Pump
BATT PWR Battery Power MAIN Main Relay
ABS Antilock Brake System COOL FAN HI Cooling Fan High
HVAC BLWR HVAC Blower PWR WNDW Power Window
IGN 2 Ignition 2 HEAD LAMPS Headlamp Relay
5-93
Capacities and Specifications
The following approximate capacities are given in English and metric conversions. See Part D: Recommended Fluids
and Lubricants on page 6-26 for more information.
Capacities
Application
English Metric
For the air conditioning system refrigerant charge
amount, see the refrigerant caution label located
Air Conditioning Refrigerant R134a under the hood. See your dealer/retailer for more
information.
Cooling System 7.9 qt 7.5 L
Engine Oil with Filter 4.2 qt 4.0 L
Fuel Tank 14.5 gal 55.0 L
Transmission, Automatic 7.3 qt 6.9 L
Transmission, Manual 1.9 qt 1.8 L
Wheel Nut Torque 81 lb ft 110 Y
All capacities are approximate. When adding, be sure to fill to the appropriate level, as recommended in this
manual. Recheck fluid level after filling.
Engine Specifications
Engine VIN Code Transmission Spark Plug Gap
Automatic and
2.0L L4 (L34) Z 0.039 inch (1.0mm)
Manual
5-94
Maintenance Replacement Parts
Replacement parts identified below by name, part number, or specification can be obtained from your dealer/retailer.
Part GM Part Number

Engine Air Cleaner/Filter 96553450
Engine Oil Filter 96458873
Fuel Filter 96335719
A/C Filter 96554378
Spark Plugs 93742299
Windshield Wiper Blades
Drivers Side 96478670
Passengers Side 96498696
Rear 96341429
5-95
Engine Drive Belt Routing
5-96
Section 6 Maintenance Schedule
Maintenance Schedule ......................................6-2 At Least Twice a Year ...................................6-20
Introduction ...................................................6-2 At Least Once a Year ...................................6-21
Maintenance Requirements ..............................6-2 Part C: Periodic Maintenance Inspections .........6-24
Your Vehicle and the Environment ....................6-2 Steering, Suspension and Front Drive Axle
How This Section is Organized .........................6-3 Boot and Seal Inspection ............................6-24
Part A: Scheduled Maintenance Services ...........6-4 Exhaust System Inspection ............................6-24
Using the Maintenance Schedule ......................6-4 Fuel System Inspection ..................................6-24
Selecting the Right Schedule ...........................6-5 Engine Cooling System Inspection ...................6-24
Short Trip/City Scheduled Maintenance ..............6-7 Throttle System Inspection .............................6-25
Long Trip/Highway Scheduled Maintenance ......6-14 Brake System Inspection ................................6-25
Part B: Owner Checks and Services ................6-19 Part D: Recommended Fluids and Lubricants ....6-26
At Each Fuel Fill ..........................................6-19 Part E: Maintenance Record ...........................6-28
At Least Once a Month .................................6-19
6-1
Maintenance Schedule Maintenance Requirements
Maintenance intervals, checks, inspections and
Introduction recommended fluids and lubricants as prescribed in this
manual are necessary to keep your vehicle in good
Important: Keep engine oil at the proper level and working condition. Any damage caused by failure
change as recommended. to follow scheduled maintenance may not be covered by
warranty.
Your Vehicle and the Environment

Proper vehicle maintenance not only helps to keep your
vehicle in good working condition, but also helps the
environment. Improper vehicle maintenance can
even affect the quality of the air we breathe. Improper
fluid levels or the wrong tire inflation can increase
Have you purchased the GM Protection Plan? The Plan the level of emissions from your vehicle. To help protect
supplements your new vehicle warranties. See your our environment, and to keep your vehicle in good
Warranty and Owner Assistance booklet or your condition, be sure to maintain your vehicle properly.
dealer/retailer for details.
6-2
How This Section is Organized Part B: Owner Checks and Services tells you what
should be checked and when. It also explains what
This maintenance schedule is divided into five parts: you can easily do to help keep your vehicle in good
condition.
Part A: Scheduled Maintenance Services explains
what to have done and how often. Some of these Part C: Periodic Maintenance Inspections explains
services can be complex, so unless you are technically important inspections that your dealer/retailer can
qualified and have the necessary equipment, you perform for you.
should let your dealer/retailer do these jobs. Part D: Recommended Fluids and Lubricants lists
Your dealer/retailer has trained and supported service some recommended products necessary to help
people that will perform the work using genuine parts. keep your vehicle properly maintained. These products,
or their equivalents, should be used whether you do
the work yourself or have it done.
{CAUTION: Part E: Maintenance Record is a place for you to
record and keep track of the maintenance performed on
Performing maintenance work on a vehicle can your vehicle. Keep your maintenance receipts. They
may be needed to qualify your vehicle for warranty
be dangerous. In trying to do some jobs, you
repairs.
can be seriously injured. Do your own
maintenance work only if you have the
required know-how and the proper tools and
equipment for the job. If you have any doubt,
have a qualified technician do the work. See
Doing Your Own Service Work on page 5-5.
If you want to purchase service information, see Service

Publications Ordering Information on page 7-15.
6-3
Part A: Scheduled Maintenance This part tells you the maintenance services you should
have done and when to schedule them.
Services When you go to your dealer/retailer for your service
In this part are scheduled maintenance services which needs, you will know that trained and supported service
are to be performed at the mileage intervals specified. people will perform the work using genuine parts.
The proper fluids and lubricants to use are listed in
Using the Maintenance Schedule Part D. Make sure whoever services your vehicle uses
these. All parts should be replaced and all necessary
We want to keep your vehicle in good working condition. repairs done before you or anyone else drives the
But we do not know exactly how you will drive it. You vehicle.
might drive short distances only a few times a week. These schedules are for vehicles that:
Or you might drive long distances all the time in
very hot, dusty weather. You might use your vehicle in carry passengers and cargo within recommended
making deliveries. Or you might drive it to work, to limits. You will find these on the Tire and Loading
do errands, or in many other ways. Information label. See Loading Your Vehicle on
page 4-18.
Because of the different ways people use their vehicles,
maintenance needs vary. You might need more are driven on reasonable road surfaces within legal
frequent checks and replacements. So please read the driving limits.
following and note how you drive. If you have use the recommended fuel. See Gasoline Octane
questions on how to keep your vehicle in good condition,
on page 5-6.
see your dealer/retailer.
6-4
Selecting the Right Schedule Short Trip/City Intervals
First you will need to decide which of the two schedules Every 3,000 Miles (5 000 km): Engine Oil and Filter
is right for your vehicle. Here is how to decide which Change (or 3 months, whichever occurs first).
schedule to follow:
Every 6,000 Miles (10 000 km): Tire Rotation.
Short Trip/City Definition
Every 15,000 Miles (25 000 km): Engine Air Cleaner
Follow the Short Trip/City Scheduled Maintenance if any Filter Inspection. Passenger Compartment Air Filter
one of these conditions is true for your vehicle: Replacement. Drive Belt(s) Inspection.
Most trips are less than 5 miles (8 km). This is Every 30,000 Miles (50 000 km): Engine Air Cleaner
particularly important when outside temperatures Filter Replacement. Spark Plug Replacement. EVAP
are below freezing. System Service. PCV System Service. Restraint
Most trips include extensive idling, such as frequent System Check.
driving in stop-and-go traffic. Every 37,500 Miles (60 000 km): Automatic
If the vehicle is used for delivery service, police, Transmission Fluid Change (severe service only).
taxi, or other commercial application.
Every 60,000 Miles (100 000 km): Spark Plug Wire
One of the reasons you should follow this schedule if Replacement. Timing Belt Replacement. EVAP System
you operate your vehicle under any of these conditions Solenoid Valve Replacement.
is that these conditions cause engine oil to break
down sooner. Every 90,000 Miles (150 000 km): Fuel Filter
Replacement.
Every 150,000 Miles (240 000 km): Cooling System
Service.
These intervals only summarize maintenance services.
Be sure to follow the complete scheduled maintenance
on the following pages.
6-5
Long Trip/Highway Definition Every 30,000 Miles (50 000 km): Engine Air Cleaner
Filter Replacement. Spark Plug Replacement. EVAP
Follow this scheduled maintenance only if none of the System Service. PCV System Service. Restraint
conditions from the Short Trip/City Scheduled System Check.
Maintenance are true. Do not use this schedule if the
vehicle is driven in a dusty area or used off paved roads. Every 37,500 Miles (60 000 km): Automatic
Use the Short Trip/City schedule for these conditions. Transmission Fluid Change (severe service only).
Driving a vehicle with a fully warmed engine under Every 60,000 Miles (100 000 km): Spark Plug Wire
highway conditions will cause engine oil to break Replacement. Timing Belt Replacement. EVAP System
down slower. Solenoid Valve Replacement.
Long Trip/Highway Intervals Every 90,000 Miles (150 000 km): Fuel Filter
Replacement.
Every 7,500 Miles (12 500 km): Engine Oil and Filter
Change (or every 12 months, whichever occurs Every 150,000 Miles (240 000 km): Cooling System
first). Tire Rotation. Service.
These intervals only summarize maintenance services.
Every 15,000 Miles (25 000 km): Engine Air Cleaner
Be sure to follow the complete scheduled maintenance
Filter Inspection. Passenger Compartment Air Filter
on the following pages.
Replacement. Drive Belt(s) Inspection.
6-6
Short Trip/City Scheduled 3,000 Miles (5 000 km)
Maintenance Change engine oil and filter (or every 3 months,
whichever occurs first). An Emission Control Service.
The services shown in this schedule up to 100,000 miles
(166 000 km) should be repeated after 100,000 miles 6,000 Miles (10 000 km)
(166 000 km) at the same intervals for the life of Change engine oil and filter (or every 3 months,
this vehicle. The services shown at 150,000 miles whichever occurs first). An Emission Control Service.
(240 000 km) should be repeated at the same interval
after 150,000 miles (240 000 km) for the life of this Rotate tires. See Tire Inspection and Rotation
vehicle. on page 5-60 for proper rotation pattern and
additional information. (See footnote +.)
See Part B: Owner Checks and Services on page 6-19
and Part C: Periodic Maintenance Inspections on 9,000 Miles (15 000 km)
page 6-24.
Change engine oil and filter (or every 3 months,
Footnotes whichever occurs first). An Emission Control Service.
The U.S. Environmental Protection Agency or the 12,000 Miles (20 000 km)
California Air Resources Board has determined that the Change engine oil and filter (or every 3 months,
failure to perform this maintenance item will not nullify whichever occurs first). An Emission Control Service.
the emission warranty or limit recall liability prior to
the completion of the vehicles useful life. We, however, Rotate tires. See Tire Inspection and Rotation
urge that all recommended maintenance services be on page 5-60 for proper rotation pattern and
performed at the indicated intervals and the additional information. (See footnote +.)
maintenance be recorded.
+ A good time to check your brakes is during tire
rotation. See Brake System Inspection on page 6-25.
6-7
15,000 Miles (25 000 km) 24,000 Miles (40 000 km)
Change engine oil and filter (or every 3 months, Change engine oil and filter (or every 3 months,
whichever occurs first). An Emission Control Service. whichever occurs first). An Emission Control Service.
Replace passenger compartment air filter. If you drive Rotate tires. See Tire Inspection and Rotation
regularly under dusty conditions, the filter may on page 5-60 for proper rotation pattern and
require replacement more often. additional information. (See footnote +.)
Inspect engine air cleaner filter and replace engine
oil pan drain plug washer. If necessary, replace the
27,000 Miles (45 000 km)
filter. If vehicle is driven in dusty/dirty conditions, Change engine oil and filter (or every 3 months,
inspect filter at every engine oil change. See Engine whichever occurs first). An Emission Control Service.
Air Cleaner/Filter on page 5-16 for more information.
Inspect drive belt(s).
30,000 Miles (50 000 km)
18,000 Miles (30 000 km) whichever occurs first). An Emission Control Service.
Change engine oil and filter (or every 3 months, Replace passenger compartment air filter. If you drive
whichever occurs first). An Emission Control Service. regularly under dusty conditions, the filter may
Rotate tires. See Tire Inspection and Rotation require replacement more often.
on page 5-60 for proper rotation pattern and Replace engine air cleaner filter. See Engine Air
additional information. (See footnote +.) Cleaner/Filter on page 5-16 for more information.
Rotate tires. See Tire Inspection and Rotation on
21,000 Miles (35 000 km) page 5-60 for proper rotation pattern and additional
Change engine oil and filter (or every 3 months, information. (See footnote +.)
whichever occurs first). An Emission Control Service. Replace spark plugs. An Emission Control Service.
6-8
Check restraint system. Make sure the safety belt 37,500 Miles (60 000 km)
reminder light and safety belt assemblies are
working properly. Look for any other loose or Change automatic transmission fluid if the vehicle is
damaged safety belt system parts. If you see mainly driven under one or more of these conditions:
anything that might keep a safety belt system from In heavy city traffic where the outside
doing its job, have it repaired. Have any torn or frayed temperature regularly reaches 90F (32C)
safety belts replaced. Also see Checking the or higher.
Restraint Systems on page 1-66. In hilly or mountainous terrain.
Inspect drive belt(s). Uses such as found in taxi, police, or delivery
Inspect EVAP canister, vapor lines, and EVAP vent service.
solenoid valve. An Emission Control Service. If you do not use your vehicle under any of these
(See footnote .) conditions, the fluid does not require changing.
Inspect PCV system. An Emission Control Service.
(See footnote .) 39,000 Miles (65 000 km)
33,000 Miles (55 000 km) Change engine oil and filter (or every 3 months,
whichever occurs first). An Emission Control Service. 42,000 Miles (70 000 km)
36,000 Miles (60 000 km) Change engine oil and filter (or every 3 months,
Change engine oil and filter (or every 3 months, Rotate tires. See Tire Inspection and Rotation
whichever occurs first). An Emission Control Service. on page 5-60 for proper rotation pattern and
Rotate tires. See Tire Inspection and Rotation additional information. (See footnote +.)
on page 5-60 for proper rotation pattern and
6-9
45,000 Miles (75 000 km) 54,000 Miles (90 000 km)
Replace passenger compartment air filter. If you drive Rotate tires. See Tire Inspection and Rotation
regularly under dusty conditions, the filter may on page 5-60 for proper rotation pattern and
require replacement more often. additional information. (See footnote +.)
Inspect engine air cleaner filter. If necessary, replace
the filter. If vehicle is driven in dusty/dirty conditions,
57,000 Miles (95 000 km)
inspect filter at every engine oil change. See Change engine oil and filter (or every 3 months,
Engine Air Cleaner/Filter on page 5-16 for more whichever occurs first). An Emission Control Service.
information.
60,000 Miles (100 000 km)
48,000 Miles (80 000 km) whichever occurs first). An Emission Control Service.
Change engine oil and filter (or every 3 months, Replace passenger compartment air filter. If you drive
whichever occurs first). An Emission Control Service. regularly under dusty conditions, the filter may
Rotate tires. See Tire Inspection and Rotation require replacement more often.
on page 5-60 for proper rotation pattern and Replace engine air cleaner filter. See Engine Air
additional information. (See footnote +.) Cleaner/Filter on page 5-16 for more information.
51,000 Miles (85 000 km) page 5-60 for proper rotation pattern and additional
Change engine oil and filter (or every 3 months, information. (See footnote +.)
whichever occurs first). An Emission Control Service. Replace spark plugs. An Emission Control Service.
Replace spark plug wires. An Emission Control
Service.
6-10
Check restraint system. Make sure the safety belt 69,000 Miles (115 000 km)
reminder light and safety belt assemblies are
working properly. Look for any other loose or Change engine oil and filter (or every 3 months,
damaged safety belt system parts. If you see whichever occurs first). An Emission Control Service.
anything that might keep a safety belt system from
doing its job, have it repaired. Have any torn or frayed
72,000 Miles (120 000 km)
safety belts replaced. Also see Checking the Change engine oil and filter (or every 3 months,
Restraint Systems on page 1-66. whichever occurs first). An Emission Control Service.
Inspect drive belt(s). Rotate tires. See Tire Inspection and Rotation
Replace timing belt. on page 5-60 for proper rotation pattern and
Inspect EVAP canister and vapor lines. Replace
EVAP vent solenoid valve. An Emission Control 75,000 Miles (125 000 km)
Service. (See footnote .)
Inspect PCV system. An Emission Control Service. whichever occurs first). An Emission Control Service.
(See footnote .)
Replace passenger compartment air filter. If you drive
63,000 Miles (105 000 km) regularly under dusty conditions, the filter may
require replacement more often.
whichever occurs first). An Emission Control Service. Inspect engine air cleaner filter. If necessary, replace
the filter. If vehicle is driven in dusty/dirty conditions,
66,000 Miles (110 000 km) inspect filter at every engine oil change. See
Engine Air Cleaner/Filter on page 5-16 for more
Change engine oil and filter (or every 3 months, information.
Rotate tires. See Tire Inspection and Rotation
6-11
Change automatic transmission fluid if the vehicle is 84,000 Miles (140 000 km)
mainly driven under one or more of these conditions:
In heavy city traffic where the outside whichever occurs first). An Emission Control Service.
temperature regularly reaches 90F (32C)
or higher. Rotate tires. See Tire Inspection and Rotation
In hilly or mountainous terrain. additional information. (See footnote +.)
Uses such as found in taxi, police, or delivery
service. 87,000 Miles (145 000 km)
If you do not use your vehicle under any of these Change engine oil and filter (or every 3 months,
conditions, the fluid does not require changing. whichever occurs first). An Emission Control Service.
78,000 Miles (130 000 km) 90,000 Miles (150 000 km)
Rotate tires. See Tire Inspection and Rotation Replace passenger compartment air filter. If you drive
on page 5-60 for proper rotation pattern and regularly under dusty conditions, the filter may
additional information. (See footnote +.) require replacement more often.
Replace engine air cleaner filter. See Engine Air
81,000 Miles (135 000 km) Cleaner/Filter on page 5-16 for more information.
Change engine oil and filter (or every 3 months, Rotate tires. See Tire Inspection and Rotation on
whichever occurs first). An Emission Control Service. page 5-60 for proper rotation pattern and additional
information. (See footnote +.)
6-12
Replace spark plugs. An Emission Control Service. 96,000 Miles (160 000 km)
Replace fuel filter. An Emission Control Service. Change engine oil and filter (or every 3 months,
(See footnote .) whichever occurs first). An Emission Control Service.
Check restraint system. Make sure the safety belt Rotate tires. See Tire Inspection and Rotation
reminder light and safety belt assemblies are on page 5-60 for proper rotation pattern and
working properly. Look for any other loose or additional information. (See footnote +.)
damaged safety belt system parts. If you see
anything that might keep a safety belt system from 99,000 Miles (165 000 km)
doing its job, have it repaired. Have any torn or frayed
safety belts replaced. Also see Checking the Change engine oil and filter (or every 3 months,
Restraint Systems on page 1-66. whichever occurs first). An Emission Control Service.
Inspect drive belt(s). 150,000 Miles (240 000 km)
Inspect EVAP canister, vapor lines, and EVAP Drain, flush, and refill cooling system. This service
vent solenoid valve. An Emission Control Service. can be complex; you should have your dealer/retailer
(See footnote .) perform this service. See Engine Coolant on
Inspect PCV system. An Emission Control Service. page 5-19 for what to use. Inspect hoses. Clean
(See footnote .) radiator, condenser, pressure cap, and neck.
Pressure test the cooling system and pressure cap.
93,000 Miles (155 000 km) An Emission Control Service.
6-13
Long Trip/Highway Scheduled 7,500 Miles (12 500 km)
Maintenance Change engine oil and filter (or every 12 months,
whichever occurs first). An Emission Control
The services shown in this schedule up to 100,000 miles Service.
(166 000 km) should be repeated after 100,000 miles Rotate tires. See Tire Inspection and Rotation on
(166 000 km) at the same intervals for the life of page 5-60 for proper rotation pattern and additional
this vehicle. The services shown at 150,000 miles information. (See footnote +.)
(240 000 km) should be repeated at the same interval
after 150,000 miles (240 000 km) for the life of this 15,000 Miles (25 000 km)
vehicle.
See Part B: Owner Checks and Services on page 6-19 whichever occurs first). An Emission Control
and Part C: Periodic Maintenance Inspections on Service.
page 6-24.
Replace passenger compartment air filter. If you
Footnotes drive regularly under dusty conditions, the filter
may require replacement more often.
The U.S. Environmental Protection Agency or the Inspect engine air cleaner filter. See Engine Air
California Air Resources Board has determined that the Cleaner/Filter on page 5-16 for more information.
failure to perform this maintenance item will not nullify
the emission warranty or limit recall liability prior to Rotate tires. See Tire Inspection and Rotation on
the completion of the vehicles useful life. We, however, page 5-60 for proper rotation pattern and additional
urge that all recommended maintenance services be information. (See footnote +.)
performed at the indicated intervals and the Inspect drive belt(s).
maintenance be recorded.
+ A good time to check your brakes is during tire
rotation. See Brake System Inspection on page 6-25.
6-14
22,500 Miles (37 500 km) Inspect drive belt(s).
Change engine oil and filter (or every 12 months, Inspect EVAP canister, vapor lines, and EVAP
whichever occurs first). An Emission Control Service. vent solenoid valve. An Emission Control Service.
(See footnote .)
page 5-60 for proper rotation pattern and additional Inspect PCV system. An Emission Control Service.
information. (See footnote +.) (See footnote .)
30,000 Miles (50 000 km) 37,500 Miles (62 500 km)
whichever occurs first). An Emission Control Service. whichever occurs first). An Emission Control
Service.
regularly under dusty conditions, the filter may require Rotate tires. See Tire Inspection and Rotation on
replacement more often. page 5-60 for proper rotation pattern and additional
Cleaner/Filter on page 5-16 for more information. Change automatic transmission fluid if the vehicle is
mainly driven under one or more of these conditions:
page 5-60 for proper rotation pattern and additional In heavy city traffic where the outside
information. (See footnote +.) temperature regularly reaches 90F (32C)
or higher.
Replace spark plugs. An Emission Control Service.
In hilly or mountainous terrain.
Check restraint system. Make sure the safety belt
reminder light and safety belt assemblies are working Uses such as found in taxi, police, or delivery
properly. Look for any other loose or damaged safety service.
belt system parts. If you see anything that might keep If you do not use your vehicle under any of these
a safety belt system from doing its job, have it conditions, the fluid does not require changing.
repaired. Have any torn or frayed safety belts
replaced. Also see Checking the Restraint Systems on
page 1-66.
6-15
45,000 Miles (75 000 km) Replace engine air cleaner filter. See Engine Air
Cleaner/Filter on page 5-16 for more information.
whichever occurs first). An Emission Control Rotate tires. See Tire Inspection and Rotation on
Service. page 5-60 for proper rotation pattern and additional
Replace passenger compartment air filter. If you
drive regularly under dusty conditions, the filter Replace spark plugs. An Emission Control Service.
may require replacement more often. Replace spark plug wires. An Emission Control
Inspect engine air cleaner filter. See Engine Air Service.
Cleaner/Filter on page 5-16 for more information. Check restraint system. Make sure the safety belt
Rotate tires. See Tire Inspection and Rotation on reminder light and safety belt assemblies are working
page 5-60 for proper rotation pattern and additional properly. Look for any other loose or damaged safety
information. (See footnote +.) belt system parts. If you see anything that might keep
a safety belt system from doing its job, have it
Inspect drive belt(s). repaired. Have any torn or frayed safety belts
replaced. Also see Checking the Restraint Systems on
52,500 Miles (87 500 km) page 1-66.
Change engine oil and filter (or every 12 months, Inspect drive belt(s).
Replace timing belt.
page 5-60 for proper rotation pattern and additional Inspect EVAP canister and vapor lines. Replace EVAP
information. (See footnote +.) vent solenoid valve. An Emission Control Service.
(See footnote .)
60,000 Miles (100 000 km) Inspect PCV system. An Emission Control Service.
Change engine oil and filter (or every 12 months, (See footnote .)
regularly under dusty conditions, the filter may require
replacement more often.
6-16
Change engine oil and filter (or every 12 months, Change automatic transmission fluid if the vehicle is
whichever occurs first). An Emission Control mainly driven under one or more of these conditions:
Service. In heavy city traffic where the outside
Rotate tires. See Tire Inspection and Rotation on temperature regularly reaches 90F (32C) or
page 5-60 for proper rotation pattern and additional higher.
information. (See footnote +.) In hilly or mountainous terrain.
Uses such as found in taxi, police, or delivery
75,000 Miles (125 000 km) service.
Change engine oil and filter (or every 12 months, If you do not use your vehicle under any of these
whichever occurs first). An Emission Control conditions, the fluid does not require changing.
Service.
Replace passenger compartment air filter. If you 82,500 Miles (137 500 km)
drive regularly under dusty conditions, the filter Change engine oil and filter (or every 12 months,
may require replacement more often. whichever occurs first). An Emission Control
Inspect engine air cleaner filter. See Engine Air Service.
Cleaner/Filter on page 5-16 for more information. Rotate tires. See Tire Inspection and Rotation on
Rotate tires. See Tire Inspection and Rotation on page 5-60 for proper rotation pattern and additional
page 5-60 for proper rotation pattern and additional information. (See footnote +.)
6-17
Change engine oil and filter (or every 12 months, Inspect EVAP canister, vapor lines and EVAP
whichever occurs first). An Emission Control vent solenoid valve. An Emission Control Service.
Service. (See footnote .)
Replace passenger compartment air filter. If you Inspect PCV system. An Emission Control Service.
drive regularly under dusty conditions, the filter (See footnote .)
may require replacement more often. 97,500 Miles (162 500 km)
Cleaner/Filter on page 5-16 for more information. Change engine oil and filter (or every 12 months,
whichever occurs first). An Emission Control
Rotate tires. See Tire Inspection and Rotation on Service.
page 5-60 for proper rotation pattern and additional
information. (See footnote +.) Rotate tires. See Tire Inspection and Rotation on
page 5-60 for proper rotation pattern and additional
Replace spark plugs. An Emission Control Service. information. (See footnote +.)
Replace fuel filter. An Emission Control Service.
(See footnote .) 150,000 Miles (240 000 km)
Check restraint system. Make sure the safety belt Drain, flush, and refill cooling system. This service
reminder light and safety belt assemblies are can be complex; you should have your dealer/retailer
working properly. Look for any other loose or perform this service. See Engine Coolant on
damaged safety belt system parts. If you see page 5-19 for what to use. Inspect hoses. Clean
anything that might keep a safety belt system from radiator, condenser, pressure cap, and neck.
doing its job, have it repaired. Have any torn or frayed Pressure test the cooling system and pressure cap.
safety belts replaced. Also see Checking the An Emission Control Service.
Restraint Systems on page 1-66.
6-18
Part B: Owner Checks and Services Engine Coolant Level Check
Listed in this part are owner checks and services Check the engine coolant level and add DEX-COOL
which should be performed at the intervals specified to coolant mixture if necessary. See Engine Coolant
help ensure the safety, dependability and emission on page 5-19.
control performance of your vehicle. Windshield Washer Fluid Level Check
Be sure any necessary repairs are completed at once. Check the windshield washer fluid level in the windshield
Whenever any fluids or lubricants are added to your washer fluid reservoir and add the proper fluid if
vehicle, make sure they are the proper ones, as shown necessary.
in Part D.
At Each Fuel Fill At Least Once a Month

It is important to perform these underhood checks at Tire Inflation Check
each fuel fill. Inspect the tires and make sure the tires are inflated to
Engine Oil Level Check the correct pressures. Do not forget to check the
spare tire. See Inflation - Tire Pressure on page 5-56.
Notice: It is important to check the engine oil
regularly and keep it at the proper level. Failure to
keep the engine oil at the proper level can cause
damage to the engine not covered by your warranty.
Check the engine oil level and add the proper oil if
necessary. See Engine Oil on page 5-13.
6-19
At Least Twice a Year Automatic Transmission Check
It is not necessary to check the transmission fluid level.
Wiper Blade Check A transmission fluid leak is the only reason for fluid
Inspect wiper blades for wear, cracking, or loss. Check for leaks. If a leak occurs, take the vehicle
contamination. Clean the windshield and wiper blades, if to your dealer/retailer and have it repaired as soon
contaminated. Replace wiper blades that are worn or as possible.
damaged. See Windshield Wiper Blade Replacement on
page 5-48 and Windshield and Wiper Blades on Manual Transmission Check
page 5-83 for more information. It is not necessary to check the transmission fluid level.
Check for leaks. A fluid leak is the only reason for
Weatherstrip Lubrication fluid loss. Have the system inspected and repaired if
Silicone grease on weatherstrips will make them last needed.
longer, seal better, and not stick or squeak. Apply
silicone grease with a clean cloth. During very cold, Clutch and Brake Pedal Free Play
damp weather more frequent application may be Check
required. See Part D: Recommended Fluids and
Lubricants on page 6-26. Check the clutch pedal and brake pedal for free play
and adjust as necessary.
6-20
At Least Once a Year Starter Switch Check
Key Lock Cylinders Service
Lubricate the key lock cylinders with the lubricant {CAUTION:
specified in Part D.
When you are doing this inspection, the
Body Lubrication Service vehicle could move suddenly. If the vehicle
Lubricate all hood latch assemblies, secondary latch, moves, you or others could be injured.
pivots, spring anchor, release pawl, hood and body door
hinges, rear compartment, and any folding seat
hardware. Part D tells you what to use. More frequent 1. Before you start, be sure you have enough room
lubrication may be required when exposed to a corrosive around the vehicle.
environment. 2. Firmly apply both the parking brake and the regular
brake. See Parking Brake on page 2-28 if necessary.
Do not use the accelerator pedal, and be ready to
turn off the engine immediately if it starts.
3. On automatic transmission vehicles, try to start the
engine in each gear. The starter should work only
in PARK (P) or NEUTRAL (N). If the starter works in
any other position, your vehicle needs service.
On manual transmission vehicles, put the shift lever
in NEUTRAL, push the clutch pedal down halfway
and try to start the engine. The starter should
work only when the clutch pedal is pushed down all
the way to the floor. If the starter works when the
clutch pedal is not pushed all the way down,
your vehicle needs service.
6-21
Automatic Transmission Shift Lock Ignition Transmission Lock Check
Control System Check While parked, and with the parking brake set, try to turn
the ignition to LOCK/OFF in each shift lever position.
With an automatic transmission, the ignition
{CAUTION: should turn to LOCK/OFF only when the shift lever
is in PARK (P).
When you are doing this inspection, the With a manual transmission, the ignition should turn
vehicle could move suddenly. If the vehicle to LOCK/OFF only when you press the key release
moves, you or others could be injured. button.
On all vehicles, the ignition key should come out only in
1. Before you start, be sure you have enough room LOCK/OFF.
around the vehicle. It should be parked on a level Turn the steering wheel to the left and to the right. It
surface. should only lock when turned to the right.
2. Firmly apply the parking brake. See Parking Brake
on page 2-28 if necessary.
Be ready to apply the regular brake immediately if
the vehicle begins to move.
3. With the engine off, turn the ignition to ON/RUN,
but do not start the engine. Without applying the
regular brake, try to move the shift lever out
of PARK (P) with normal effort. If the shift lever
moves out of PARK (P), your vehicle needs service.
6-22
Parking Brake and Automatic Park on a fairly steep hill, with the vehicle facing
downhill. Keeping your foot on the regular brake,
Transmission Park (P) Mechanism set the parking brake.
Check To check the parking brakes holding ability: With
the engine running and transmission in
NEUTRAL (N), slowly remove foot pressure from
{CAUTION: the regular brake pedal. Do this until the vehicle is
held by the parking brake only.
When you are doing this check, your vehicle To check the PARK (P) mechanisms holding
could begin to move. You or others could be ability: With the engine running, shift to PARK (P).
injured and property could be damaged. Make Then release the parking brake followed by the
sure there is room in front of your vehicle in regular brake.
case it begins to roll. Be ready to apply the Underbody Flushing Service
regular brake at once should the vehicle begin
to move. At least every spring, use plain water to flush any
corrosive materials from the underbody. Take care to
clean thoroughly any areas where mud and other debris
can collect.
6-23
Part C: Periodic Maintenance Exhaust System Inspection
Inspections Inspect the complete exhaust system. Inspect the body
near the exhaust system. Look for broken, damaged,
Listed in this part are inspections and services which missing, or out-of-position parts as well as open seams,
should be performed at least twice a year, for instance, holes, loose connections, or other conditions which
each spring and fall. You should let your dealer/retailer could cause a heat build-up in the floor pan or could let
do these jobs. Make sure any necessary repairs exhaust fumes into the vehicle. See Engine Exhaust
are completed at once. on page 2-32.
Proper procedures to perform these services can be
found in a service manual. See Service Publications Fuel System Inspection
Ordering Information on page 7-15.
Inspect the complete fuel system for damage or leaks.
Steering, Suspension and Front
Drive Axle Boot and Seal Inspection Engine Cooling System Inspection
Inspect the front and rear suspension and steering Inspect the hoses and have them replaced if they
system for damaged, loose or missing parts, signs of are cracked, swollen or deteriorated. Inspect all pipes,
wear or lack of lubrication. Inspect the power steering fittings and clamps; replace as needed. Clean the
lines and hoses for proper hook-up, binding, leaks, outside of the radiator and air conditioning condenser.
cracks, chafing, etc. Clean and then inspect the drive To help ensure proper operation, a pressure test of
axle boot seals for damage, tears or leakage. Replace the cooling system and pressure cap is recommended
seals if necessary. at least once a year.
6-24
Throttle System Inspection Brake System Inspection
Inspect the throttle system for interference or binding, Inspect the complete system. Inspect brake lines and
and for damaged or missing parts. Replace parts hoses for proper hook-up, binding, leaks, cracks,
as needed. Replace any components that have high chafing, etc. Inspect disc brake pads for wear and rotors
effort or excessive wear. Do not lubricate accelerator for surface condition. Inspect other brake parts,
and cruise control cables. including calipers, parking brake, etc. You may need to
have your brakes inspected more often if your driving
habits or conditions result in frequent braking.
6-25
Part D: Recommended Fluids and Usage Fluid/Lubricant
Lubricants Windshield
Washer Solvent Optikleen
Washer Solvent.
Fluids and lubricants identified below by name, part
number, or specification can be obtained from your Power Steering DEXRON-VI Automatic
dealer/retailer. System Transmission Fluid.
Automatic Transmission Fluid ESSO
Usage Fluid/Lubricant Automatic
Transmission LT 71141 or TOTAL ATF H50235
(GM Part No. in Canada 89021903).
Engine oil which meets GM
Standard GM6094M and displays Manual Transmission Fluid
the American Petroleum Institute Manual
(GM Part No. U.S. 89021806,
Certified for Gasoline Engines Transmission in Canada 89021807).
Engine Oil
starburst symbol. To determine the
proper viscosity for your vehicles Key Lock Multi-Purpose Lubricant, Superlube
engine, see Engine Oil on (GM Part No. U.S. 12346241, in
Cylinders
page 5-13. Canada 10953474).
50/50 mixture of clean, drinkable Chassis Lubricant (GM Part
water and use only DEX-COOL Manual No. U.S. 12377985, in
Engine Coolant Coolant. See Engine Coolant on Transmission Canada 88901242) or lubricant
page 5-19 Shift Linkage meeting requirements of NLGI #2,
Category LB or GC-LB.
Hydraulic Brake Delco Supreme 11 Brake Fluid or
System equivalent DOT-3 brake fluid.
6-26
Usage Fluid/Lubricant Usage Fluid/Lubricant
Chassis Lubricant (GM Part Hood and Door Multi-Purpose Lubricant, Superlube
Chassis No. U.S. 12377985, in Hinges (GM Part No. U.S. 12346241, in
Lubrication Canada 88901242) or lubricant Canada 10953474).
meeting requirements of NLGI #2,
Category LB or GC-LB. Weatherstrip Lubricant (GM Part No.
Weatherstrip U.S. 3634770, in Canada 10953518)
Hood Latch or Dielectric Silicone Grease
Assembly, Lubriplate Lubricant Aerosol Conditioning (GM Part No. U.S. 12345579, in
Secondary (GM Part No. U.S. 12346293, in Canada 992887).
Latch, Canada 992723) or lubricant
Pivots, Spring meeting requirements of NLGI #2,
Anchor, and Category LB or GC-LB.
Release Pawl
6-27
Part E: Maintenance Record
After the scheduled services are performed, record the date, odometer reading, and who performed the service and
any additional information from Owner Checks and Services or Periodic Maintenance on the following record
pages. Also, you should retain all maintenance receipts.
Maintenance Record
Odometer
Date Serviced By Maintenance Record
Reading
6-28
Maintenance Record (contd)
Odometer
Reading
6-29
Maintenance Record (contd)
Odometer
Reading
6-30
Section 7 Customer Assistance Information
Customer Assistance and Information ...............7-2 Reporting Safety Defects ................................7-13
Customer Satisfaction Procedure ......................7-2 Reporting Safety Defects to the United
Online Owner Center ......................................7-4 States Government ....................................7-13
Customer Assistance for Text Reporting Safety Defects to the Canadian
Telephone (TTY) Users ................................7-4 Government ..............................................7-14
Customer Assistance Offices ............................7-5 Reporting Safety Defects to General Motors .....7-14
GM Mobility Reimbursement Program ................7-6 Service Publications Ordering Information .........7-15
Roadside Assistance Program ..........................7-6 Vehicle Data Recording and Privacy ................7-16
Scheduling Service Appointments .....................7-8 Event Data Recorders ...................................7-16
Courtesy Transportation ...................................7-9 OnStar ......................................................7-17
Collision Damage Repair ................................7-10 Navigation System ........................................7-17
Radio Frequency Identification (RFID) ..............7-17
7-1
Customer Assistance and We encourage you to call the toll-free number in order
to give your inquiry prompt attention. Please have
Information the following information available to give the Customer
Assistance Representative:
Customer Satisfaction Procedure Vehicle Identification Number (VIN). This is

available from the vehicle registration or title, or the
Your satisfaction and goodwill are important to plate at the top left of the instrument panel and
your dealer and to Chevrolet. Normally, any concerns visible through the windshield.
with the sales transaction or the operation of your Dealership name and location.
vehicle will be resolved by your dealers sales or service
departments. Sometimes, however, despite the best Vehicle delivery date and present mileage
intentions of all concerned, misunderstandings can (kilometers).
occur. If your concern has not been resolved to your When contacting Chevrolet, please remember that your
satisfaction, the following steps should be taken: concern will likely be resolved at a dealers facility.
STEP ONE: Discuss your concern with a member of That is why we suggest you follow Step One first if you
dealership management. Normally, concerns can have a concern.
be quickly resolved at that level. If the matter has STEP THREE U.S. Owners: Both General Motors
already been reviewed with the sales, service, or parts and your dealer are committed to making sure you
manager, contact the owner of the dealership or the are completely satisfied with your new vehicle. However,
general manager. if you continue to remain unsatisfied after following
STEP TWO: If after contacting a member of dealership the procedure outlined in Steps One and Two,
management, it appears your concern cannot be you should file with the Better Business Bureau (BBB)
resolved by the dealership without further help, in the Auto Line Program to enforce your rights.
U.S., contact the Chevrolet Customer Assistance Center The BBB Auto Line Program is an out of court program
by calling 1-800-222-1020. In Canada, contact General administered by the Council of Better Business
Motors of Canada Customer Communication Centre Bureaus to settle automotive disputes regarding vehicle
by calling 1-800-263-3777 (English) or 1-800-263-7854 repairs or the interpretation of the New Vehicle
(French). Limited Warranty. Although you may be required to
7-2
resort to this informal dispute resolution program prior to Arbitration Program. General Motors of Canada Limited
filing a court action, use of the program is free of has committed to binding arbitration of owner disputes
charge and your case will generally be heard within involving factory-related vehicle service claims. The
40 days. If you do not agree with the decision given in program provides for the review of the facts involved by
your case, you may reject it and proceed with any other an impartial third party arbiter, and may include an
venue for relief available to you. informal hearing before the arbiter. The program
is designed so that the entire dispute settlement
You may contact the BBB Auto Line Program using the process, from the time you file your complaint to the
toll-free telephone number or write them at the final decision, should be completed in about 70 days.
following address: We believe our impartial program offers advantages over
BBB Auto Line Program courts in most jurisdictions because it is informal,
Council of Better Business Bureaus, Inc. quick, and free of charge.
4200 Wilson Boulevard
Suite 800 For further information concerning eligibility in the
Arlington, VA 22203-1838 Canadian Motor Vehicle Arbitration Plan (CAMVAP), call
toll-free 1-800-207-0685. Alternatively, you may call
Telephone: 1-800-955-5100 the General Motors Customer Communication Centre,
This program is available in all 50 states and the District 1-800-263-3777 (English), 1-800-263-7854 (French),
of Columbia. Eligibility is limited by vehicle age, or you may write to:
mileage, and other factors. General Motors reserves the The Mediation/Arbitration Program
right to change eligibility limitations and/or discontinue c/o Customer Communication Centre
its participation in this program. General Motors of Canada Limited
STEP THREE Canadian Owners: In the event that Mail Code: CA1-163-005
you do not feel your concerns have been addressed 1908 Colonel Sam Drive
Oshawa, Ontario L1H 8P7
after following the procedure outlined in Steps 1 and 2,
General Motors of Canada Limited wants you to be Your inquiry should be accompanied by your Vehicle
aware of its participation in a no-charge Mediation/ Identification Number (VIN).
7-3
Online Owner Center Here are a few of the valuable tools and services you
will have access to:
(United States only) My Showroom: Find and save information on
vehicles and current offers in your area.
The Owner Center is a resource for your GM ownership
My Dealers/Retailers: Save details such as
needs. Specific vehicle information can be found in
address and phone number for each of your
one place.
preferred GM Dealers or Retailers.
The Online Owner Center allows you to: My Driveway: Receive service reminders and
Get e-mail service reminders. helpful advice on owning and maintaining
your vehicle.
Access information about your specific vehicle,
including tips and videos and an electronic My Preferences: Manage your profile, subscribe to
version of this owner manual. E-News and use tools and forms with greater ease.
Keep track of your vehicles service history and To sign up to My GM Canada, visit the My GM Canada
maintenance schedule. section within www.gmcanada.com.
Find GM dealers/retailers for service nationwide.
Customer Assistance for Text
Receive special promotions and privileges only
available to members. Telephone (TTY) Users
Refer to www.MyGMLink.com on the web for updated To assist customers who are deaf, hard of hearing,
information and to register your vehicle. or speech-impaired and who use Text Telephones
(TTYs), Chevrolet has TTY equipment available at
My GM Canada (Canada only) its Customer Assistance Center. Any TTY user in
My GM Canada is a password-protected section of the U.S. can communicate with Chevrolet by
gmcanada.com where you can save information on dialing: 1-800-833-CHEV (2438). (TTY users in
GM vehicles, get personalized offers, and use handy Canada can dial 1-800-263-3830.)
tools and forms with greater ease.
7-4
Customer Assistance Offices Canada Customer Assistance
Chevrolet encourages customers to call the toll-free General Motors of Canada Limited
number for assistance. However, if a customer wishes Customer Communication Centre, CA1-163-005
to write or e-mail Chevrolet, the letter should be 1908 Colonel Sam Drive
addressed to: Oshawa, Ontario L1H 8P7
www.gmcanada.com
United States Customer Assistance 1-800-263-3777 (English)
1-800-263-7854 (French)
Chevrolet Motor Division 1-800-263-3830 (For Text Telephone
Chevrolet Customer Assistance Center devices (TTYs))
P.O. Box 33170 Roadside Assistance: 1-800-268-6800
Detroit, MI 48232-5170
www.Chevrolet.com Overseas Customer Assistance
1-800-222-1020
1-800-833-2438 (For Text Telephone Please contact the local General Motors Business Unit.
devices (TTYs)) Mexico, Central America and
Roadside Assistance: 1-800-CHEV-USA (243-8872)
Fax Number: 313-381-0022 Caribbean Islands/Countries
From Puerto Rico: (Except Puerto Rico and U.S. Virgin
1-800-496-9992 (English) Islands) Customer Assistance
1-800-496-9993 (Spanish)
Fax Number: 313-381-0022 General Motors de Mexico, S. de R.L. de C.V.
From U.S. Virgin Islands: Customer Assistance Center
1-800-496-9994 Paseo de la Reforma # 2740
Fax Number: 313-381-0022 Col. Lomas de Bezares
C.P. 11910, Mexico, D.F.
01-800-508-0000
Long Distance: 011-52-53 29 0 800
7-5
GM Mobility Reimbursement Roadside Assistance Program
Program For vehicles purchased in the U.S.,
call 1-800-CHEV-USA (1-800-243-8872);
(Text telephone (TTY): 1-888-889-2438).
For vehicles purchased in Canada, call 1-800-268-6800.
Service is available 24 hours a day, 365 days a year.
As the owner of a new Chevrolet vehicle, you are
automatically enrolled in the Chevrolet Roadside
Assistance program.
This program, available to qualified applicants, can Who is Covered?

reimburse you up to $1,000 of the cost of eligible Roadside Assistance coverage is for the vehicle
aftermarket adaptive equipment required for your vehicle, operator, regardless of ownership. In Canada, a person
such as hand controls or a wheelchair/scooter lift. driving this vehicle without the consent of the owner
The offer is available for a very limited period of time is not eligible for coverage.
from the date of vehicle purchase/lease. For more
details, or to determine your vehicles eligibility, visit
gmmobility.com or call the GM Mobility Assistance
Center at 1-800-323-9935. Text telephone (TTY) users,
call 1-800-833-9935.
General Motors of Canada also has a Mobility Program.
Call 1-800-GM-DRIVE (463-7483) for details. TTY
users call 1-800-263-3830.
7-6
Services Provided Jump Start: A battery jump start is covered at no
The following services are provided in the U.S. and charge if the vehicle does not start.
Canada up to 5 years/100,000 miles (160 000 km), Trip Routing Service (Canada only): Upon request,
whichever occurs first, and, in Canada only, up Roadside Assistance will send you detailed,
to a maximum coverage of $100. computer personalized maps, highlighting your
Fuel Delivery: Delivery of enough fuel for the choice of either the most direct route or the most
vehicle to get to the nearest service station scenic route to your destination, anywhere in North
(approximately $5 in Canada). In Canada, service America, along with helpful travel information
to provide diesel may be restricted. For safety pertaining to your trip.
reasons, propane and other alternative fuels will not Please allow three weeks before your planned
be provided through this service. departure date. Trip routing requests will be limited to
Lock-out Service: Lock-out service will be covered six per calendar year.
at no charge if you are unable to gain entry into Trip Interruption Benefits and Assistance
your vehicle. A remote unlock may be available if (Canada only): In the event of a warranty related
you have an active OnStar subscription. To ensure vehicle disablement, while en route and over
security, the driver must present personal 250 kilometres from the original point of departure,
identification before lock-out service is provided. In you may qualify for trip interruption expense
Canada, the vehicle registration is also required. assistance. This assistance covers reasonable
Emergency Tow From a Public Roadway or reimbursement of up to a maximum of $500
Highway: Tow to the nearest dealership for warranty (Canadian) for (A) meals (maximum of $50/day),
service or in the event of a vehicle-disabling crash. (B) lodging (maximum of $100/night) and
Winch-out assistance is provided when the vehicle is (C) alternate ground transportation (maximum of
mired in sand, mud, or snow. $40/day). This benefit is to assist you with some of
the unplanned expense you may incur while waiting
Flat Tire Change: Installation of a spare tire in good for your vehicle to be repaired.
condition, when equipped and properly inflated, is
covered at no charge. The customer is responsible Pre-authorization, original detailed receipts and a
for the repair or replacement of the tire if not covered copy of the repair order are required.
by a warrantable failure.
7-7
Once authorization has been given, your advisor will Model, year, color, and license plate number of the
help you make any necessary arrangements and vehicle
explain how to claim for trip interruption expense
assistance. Odometer reading, Vehicle Identification Number
(VIN), and delivery date of the vehicle
Alternative Service (Canada only): There may be
times, when Roadside Assistance cannot provide Description of the problem
timely assistance. Your advisor may authorize you to Towing and Road Service Exclusions
secure local emergency road service, and you will be
reimbursed up to $100 upon submission of the Specifically excluded from Roadside Assistance
original receipt to Roadside Assistance. coverage are towing or services for vehicles operated on
a non-public roadway or highway, fines, impound towing
In many instances, mechanical failures may be covered.
caused by a violation of local, Municipal, State,
However, any cost for parts and labor for non-warranty
Provincial, or Federal law, and mounting, dismounting or
repairs are the responsibility of the driver.
changing of snow tires, chains, or other traction devices.
Chevrolet and General Motors of Canada Limited
Roadside Assistance is not part of or included in the
reserve the right to limit services or reimbursement to
coverage provided by the New Vehicle Limited Warranty.
an owner or driver when, in their sole discretion,
Chevrolet and General Motors of Canada Limited
the claims become excessive in frequency or type of
reserve the right to make any changes or discontinue
occurrence.
the Roadside Assistance program at any time without
Calling for Assistance notification.
For prompt and efficient assistance when calling, please
provide the following to the Roadside Assistance Scheduling Service Appointments
Representative:
When your vehicle requires warranty service, contact
Your name, home address, and home telephone your dealer/retailer and request an appointment.
number By scheduling a service appointment and advising your
Telephone number of your location service consultant of your transportation needs, your
dealer/retailer can help minimize your inconvenience.
Location of the vehicle
7-8
If your vehicle cannot be scheduled into the service Transportation Options
department immediately, keep driving it until it can be
scheduled for service, unless, of course, the problem is Warranty service can generally be completed while you
safety-related. If it is, please call your dealership/retailer, wait. However, if you are unable to wait, GM helps
let them know this, and ask for instructions. to minimize your inconvenience by providing several
transportation options. Depending on the circumstances,
If the dealer/retailer requests that you simply drop the your dealer can offer you one of the following:
vehicle off for service, you are urged to do so as early in
the work day as possible to allow for the same day repair. Shuttle Service
Shuttle service is the preferred means of offering
Courtesy Transportation Courtesy Transportation. Dealers may provide you with
shuttle service to get you to your destination with
To enhance your ownership experience, we and our minimal interruption of your daily schedule. This includes
participating dealers are proud to offer Courtesy one-way or round trip shuttle service within reasonable
Transportation, a customer support program for vehicles time and distance parameters of the dealers area.
with the Bumper to Bumper (Base Warranty Coverage
period in Canada) and extended powertrain warranty Public Transportation or Fuel
in both the U.S. and Canada. Reimbursement
Several courtesy transportation options are available to If your vehicle requires overnight warranty repairs, and
assist in reducing your inconvenience when warranty public transportation is used instead of the dealers
repairs are required. shuttle service, the expense must be supported
Courtesy Transportation is not a part of the New Vehicle by original receipts and can only be up to the maximum
Limited Warranty. A separate booklet entitled Warranty amount allowed by GM for shuttle service. In addition,
and Owner Assistance Information furnished with for U.S. customers, should you arrange transportation
each new vehicle provides detailed warranty coverage through a friend or relative, limited reimbursement
information. for reasonable fuel expenses may be available.
7-9
Claim amounts should reflect actual costs and be Additional Program Information
supported by original receipts. See your dealer for
information regarding the allowance amounts for All program options, such as shuttle service, may not be
reimbursement of fuel or other transportation costs. available at every dealer. Please contact your dealer
for specific information about availability. All Courtesy
Courtesy Rental Vehicle Transportation arrangements will be administered
Your dealer may arrange to provide you with a courtesy by appropriate dealer personnel.
rental vehicle or reimburse you for a rental vehicle General Motors reserves the right to unilaterally modify,
that you obtain if your vehicle is kept for an overnight change or discontinue Courtesy Transportation at
warranty repair. Rental reimbursement will be limited any time and to resolve all questions of claim eligibility
and must be supported by original receipts. This pursuant to the terms and conditions described
requires that you sign and complete a rental agreement herein at its sole discretion.
and meet state/provincial, local, and rental vehicle
provider requirements. Requirements vary and may
include minimum age requirements, insurance coverage,
Collision Damage Repair
credit card, etc. You are responsible for fuel usage If your vehicle is involved in a collision and it is
charges and may also be responsible for taxes, levies, damaged, have the damage repaired by a qualified
usage fees, excessive mileage, or rental usage technician using the proper equipment and quality
beyond the completion of the repair. replacement parts. Poorly performed collision repairs
It may not be possible to provide a like-vehicle as a diminish your vehicles resale value, and safety
courtesy rental. performance can be compromised in subsequent
collisions.
7-10
Collision Parts Repair Facility
Genuine GM Collision parts are new parts made with the GM also recommends that you choose a collision repair
same materials and construction methods as the parts facility that meets your needs before you ever need
with which your vehicle was originally built. Genuine GM collision repairs. Your dealer/retailer may have a
Collision parts are your best choice to ensure that your collision repair center with GM-trained technicians and
vehicles designed appearance, durability, and safety are state of the art equipment, or be able to recommend
preserved. The use of Genuine GM parts can help a collision repair center that has GM-trained technicians
maintain your GM New Vehicle Warranty. and comparable equipment.
Recycled original equipment parts may also be used for Insuring Your Vehicle
repair. These parts are typically removed from vehicles
that were total losses in prior crashes. In most cases, Protect your investment in your GM vehicle with
the parts being recycled are from undamaged sections comprehensive and collision insurance coverage. There
of the vehicle. A recycled original equipment GM are significant differences in the quality of coverage
part, may be an acceptable choice to maintain your afforded by various insurance policy terms. Many
vehicles originally designed appearance and safety insurance policies provide reduced protection to your
performance, however, the history of these parts is not GM vehicle by limiting compensation for damage repairs
known. Such parts are not covered by your GM New by using aftermarket collision parts. Some insurance
Vehicle Limited Warranty, and any related failures companies will not specify aftermarket collision
are not covered by that warranty. parts. When purchasing insurance, we recommend that
you assure your vehicle will be repaired with GM
Aftermarket collision parts are also available. These are original equipment collision parts. If such insurance
made by companies other than GM and may not coverage is not available from your current insurance
have been tested for your vehicle. As a result, these carrier, consider switching to another insurance carrier.
parts may fit poorly, exhibit premature If your vehicle is leased, the leasing company may
durability/corrosion problems, and may not perform require you to have insurance that assures repairs with
properly in subsequent collisions. Aftermarket parts are Genuine GM Original Equipment Manufacturer (OEM)
not covered by your GM New Vehicle Limited parts or Genuine Manufacturer replacement parts. Read
Warranty, and any vehicle failure related to such parts your lease carefully, as you may be charged at the
are not covered by that warranty. end of your lease for poor quality repairs.
7-11
If a Crash Occurs Remove any valuables from your vehicle before it is
towed away. Make sure this includes your insurance
Here is what to do if you are involved in a crash. information and registration if you keep these
Try to relax and then check to make sure you are items in your vehicle.
all right. If you are uninjured, make sure that no Gather the important information you will need from
one else in your vehicle, or the other vehicle, the other driver. Things like name, address, phone
is injured. number, drivers license number, vehicle license
If there has been an injury, call emergency services plate, vehicle make, model and model year, Vehicle
for help. Do not leave the scene of a crash until all Identification Number (VIN), insurance company
matters have been taken care of. Move your and policy number, and a general description of the
vehicle only if its position puts you in danger or you damage to the other vehicle.
are instructed to move it by a police officer. If possible, call your insurance company from the
Give only the necessary and requested information scene of the crash. They will walk you through
to police and other parties involved in the crash. the information they will need. If they ask for
Do not discuss your personal condition, mental a police report, phone or go to the police
frame of mind, or anything unrelated to the crash. department headquarters the next day and you can
This will help guard against post-crash legal action. get a copy of the report for a nominal fee. In
some states/provinces with no fault insurance
If you need roadside assistance, call GM Roadside laws, a report may not be necessary. This is
Assistance. See Roadside Assistance Program on especially true if there are no injuries and both
page 7-6 for more information. vehicles are driveable.
If your vehicle cannot be driven, know where the Choose a reputable collision repair facility for your
towing service will be taking it. Get a card from vehicle. Whether you select a dealer/retailer or a
the tow truck operator or write down the drivers private collision repair facility to fix the damage,
name, the services name, and the phone number. make sure you are comfortable with them.
Remember, you will have to feel comfortable with
their work for a long time.
7-12
Once you have an estimate, read it carefully and If another partys insurance company is paying for the
make sure you understand what work will be repairs, you are not obligated to accept a repair
performed on your vehicle. If you have a question, valuation based on that insurance companys collision
ask for an explanation. Reputable shops welcome policy repair limits, as you have no contractual limits with
this opportunity. that company. In such cases, you can have control of
the repair and parts choices as long as cost stays within
Managing the Vehicle Damage Repair reasonable limits.
Process
In the event that your vehicle requires damage repairs,
Reporting Safety Defects
GM recommends that you take an active role in its
repair. If you have a pre-determined repair facility of Reporting Safety Defects to the
choice, take your vehicle there, or have it towed there.
Specify to the facility that any required replacement United States Government
collision parts be original equipment parts, either new
Genuine GM parts or recycled original GM parts. If you believe that your vehicle has a defect which
Remember, recycled parts will not be covered by your could cause a crash or could cause injury or
GM vehicle warranty. death, you should immediately inform the National
Highway Traffic Safety Administration (NHTSA)
Insurance pays the bill for the repair, but you must live in addition to notifying General Motors.
with the repair. Depending on your policy limits, your
insurance company may initially value the repair using If NHTSA receives similar complaints, it may open
aftermarket parts. Discuss this with your repair an investigation, and if it finds that a safety defect
professional, and insist on Genuine GM parts. Remember exists in a group of vehicles, it may order a recall
if your vehicle is leased you may be obligated to have the and remedy campaign. However, NHTSA cannot
vehicle repaired with Genuine GM parts, even if your become involved in individual problems between
insurance coverage does not pay the full cost. you, your dealer/retailer, or General Motors.
7-13
To contact NHTSA, you may call the Vehicle Reporting Safety Defects to General
Safety Hotline toll-free at 1-888-327-4236 (TTY:
1-800-424-9153); go to http://www.safercar.gov; Motors
or write to:
In addition to notifying NHTSA (or Transport Canada) in
Administrator, NHTSA a situation like this, please notify General Motors.
400 Seventh Street, SW.
Washington D.C., 20590 Call 1-800-222-1020, or write:
You can also obtain other information about motor Chevrolet Motor Division
Chevrolet Customer Assistance Center
vehicle safety from http://www.safercar.gov. P.O. Box 33170
Detroit, MI 48232-5170
Reporting Safety Defects to In Canada, call 1-800-263-3777 (English) or
the Canadian Government 1-800-263-7854 (French), or write:
General Motors of Canada Limited
If you live in Canada, and you believe that your vehicle Customer Communication Centre, CA1-163-005
has a safety defect, notify Transport Canada 1908 Colonel Sam Drive
immediately, in addition to notifying General Motors of Oshawa, Ontario L1H 8P7
Canada Limited. Call them at 1-800-333-0510 or
write to:
Transport Canada
Road Safety Branch
2780 Sheffield Road
Ottawa, Ontario K1B 3V9
7-14
Service Publications Ordering Current and Past Model Order Forms
Information Technical Service Bulletins and Manuals are available
for current and past model GM vehicles. To request
Service Manuals an order form, specify year and model name of
the vehicle.
Service Manuals have the diagnosis and repair
information on engines, transmission, axle suspension, ORDER TOLL FREE: 1-800-551-4123
brakes, electrical, steering, body, etc. Monday-Friday 8:00 AM - 6:00 PM
Service Bulletins Eastern Time
For Credit Card Orders Only
Service Bulletins give additional technical service (VISA-MasterCard-Discover), visit Helm, Inc. on the
information needed to knowledgeably service General World Wide Web at: www.helminc.com
Motors cars and trucks. Each bulletin contains
instructions to assist in the diagnosis and service of Or you can write to:
your vehicle. Helm, Incorporated
P.O. Box 07130
Owner Information Detroit, MI 48207
Owner publications are written specifically for owners Prices are subject to change without notice and without
and intended to provide basic operational information incurring obligation. Allow ample time for delivery.
about the vehicle. The owner manual includes the
Maintenance Schedule for all models. Note to Canadian Customers: All listed prices are
quoted in U.S. funds. Canadian residents are to make
In-Portfolio: Includes a Portfolio, Owner Manual, and checks payable in U.S. funds.
Warranty Booklet.
RETAIL SELL PRICE: $35.00 (U.S.) plus processing fee
Without Portfolio: Owner Manual only.
RETAIL SELL PRICE: $25.00 (U.S.) plus processing fee
7-15
Vehicle Data Recording and Event Data Recorders
Privacy This vehicle has an Event Data Recorder (EDR). The
main purpose of an EDR is to record, in certain crash or
Your GM vehicle has a number of sophisticated near crash-like situations, such as an airbag deployment
computers that record information about the vehicles or hitting a road obstacle, data that will assist in
performance and how it is driven. For example, understanding how a vehicles systems performed. The
your vehicle uses computer modules to monitor and EDR is designed to record data related to vehicle
control engine and transmission performance, to monitor dynamics and safety systems for a short period of time,
the conditions for airbag deployment and deploy typically 30 seconds or less. The EDR in this vehicle
airbags in a crash and, if so equipped, to provide is designed to record such data as:
antilock braking to help the driver control the vehicle.
These modules may store data to help your How various systems in your vehicle were operating
dealer/retailer technician service your vehicle. Some Whether or not the driver and passenger safety
modules may also store data about how you operate the belts were buckled/fastened
vehicle, such as rate of fuel consumption or average
speed. These modules may also retain the owners How far, if at all, the driver was pressing the
personal preferences, such as radio pre-sets, seat accelerator and/or brake pedal
positions, and temperature settings. How fast the vehicle was traveling
This data can help provide a better understanding of the
circumstances in which crashes and injuries occur.
Important: EDR data is recorded by your vehicle only
if a non-trivial crash situation occurs; no data is
recorded by the EDR under normal driving conditions
and no personal data (e.g., name, gender, age,
and crash location) is recorded. However, other parties,
such as law enforcement, could combine the EDR
data with the type of personally identifying data routinely
acquired during a crash investigation.
7-16
To read data recorded by an EDR, special equipment is Navigation System
required, and access to the vehicle or the EDR is
needed. In addition to the vehicle manufacturer, other If your vehicle has a navigation system, use of the
parties, such as law enforcement, that have the special system may result in the storage of destinations,
equipment, can read the information if they have addresses, telephone numbers, and other trip
access to the vehicle or the EDR. information. Refer to the navigation system operating
GM will not access this data or share it with others manual for information on stored data and for deletion
except: with the consent of the vehicle owner or, if the instructions.
vehicle is leased, with the consent of the lessee; in
response to an official request of police or similar Radio Frequency
government office; as part of GMs defense of litigation
through the discovery process; or, as required by Identification (RFID)
law. Data that GM collects or receives may also be used
RFID technology is used in some vehicles for functions
for GM research needs or may be made available to
such as tire pressure monitoring and ignition system
others for research purposes, where a need is shown
security, as well as in connection with conveniences
and the data is not tied to a specific vehicle or
such as key fobs for remote door locking/unlocking and
vehicle owner.
starting, and in-vehicle transmitters for garage door
openers. RFID technology in GM vehicles does not use
OnStar or record personal information or link with any other
GM system containing personal information.
If your vehicle has OnStar and you subscribe to the
OnStar services, please refer to the OnStar Terms and
Conditions for information on data collection and use.
7-17
NOTES
7-18
A Antilock Brake System (ABS) ............................. 4-4
Antilock Brake, System Warning Light ................ 3-32
Accessories and Modifications ............................ 5-4 Appearance Care
Adding Equipment to Your Airbag-Equipped Aluminum Wheels ........................................ 5-84
Vehicle ....................................................... 1-64 Care of Safety Belts .................................... 5-81
Additives, Fuel ................................................. 5-6 Chemical Paint Spotting ............................... 5-85
Add-On Electrical Equipment ............................ 5-88 Cleaning Exterior Lamps/Lenses .................... 5-82
Air Cleaner/Filter, Engine ................................. 5-16 Fabric/Carpet .............................................. 5-80
Air Conditioning .............................................. 3-19 Finish Care ................................................. 5-82
Airbag Finish Damage ............................................ 5-85
Passenger Status Indicator ........................... 3-28 Instrument Panel, Vinyl, and Other Plastic
Readiness Light .......................................... 3-27 Surfaces ................................................. 5-81
Airbag System ................................................ 1-51 Interior Cleaning .......................................... 5-79
What Will You See After an Airbag Inflates? .... 1-58 Leather ...................................................... 5-81
When Should an Airbag Inflate? .................... 1-56 Sheet Metal Damage ................................... 5-84
Where Are the Airbags? ............................... 1-54 Tires .......................................................... 5-84
Airbag Systems Underbody Maintenance ............................... 5-85
Adding Equipment to Your Airbag-Equipped Vehicle Care/Appearance Materials ................ 5-86
Vehicle ................................................... 1-64 Washing Your Vehicle ................................... 5-82
How Does an Airbag Restrain? ...................... 1-57 Weatherstrips .............................................. 5-82
Passenger Sensing System ........................... 1-59 Windshield and Wiper Blades ........................ 5-83
Servicing Your Airbag-Equipped Vehicle .......... 1-64 Appointments, Scheduling Service ....................... 7-8
What Makes an Airbag Inflate? ...................... 1-57 Ashtray ......................................................... 3-17
Antenna, Integrated Windshield ......................... 3-63
1
Audio System ................................................. 3-41 Break-In, New Vehicle ..................................... 2-17
Audio Steering Wheel Controls ...................... 3-61 Bulb Replacement ........................................... 5-40
Care of Your CD Player ............................... 3-63 Center High-Mounted Stoplamp (CHMSL) ........ 5-45
Care of Your CDs ........................................ 3-63 Front Turn Signal and Parking Lamps ............. 5-42
Integrated Windshield Antenna ....................... 3-63 Halogen Bulbs ............................................ 5-40
Radio Reception .......................................... 3-62 Headlamp Aiming ........................................ 5-40
Radio with CD ............................................ 3-42 Headlamps ................................................. 5-41
Radio with Six-Disc CD ................................ 3-48 License Plate Lamps .................................... 5-47
Automatic Transmission Replacement Bulbs ...................................... 5-48
Fluid .......................................................... 5-18 Sidemarker Lamps ....................................... 5-44
Operation ................................................... 2-22 Taillamps, Stoplamps and Back-Up Lamps ...... 5-47
Taillamps, Turn Signal, and Stoplamps ............ 5-46
Taillamps, Turn Signal, Stoplamps and
B Back-up Lamps ........................................
Turn Signal Lamps ......................................
5-46
5-43
Battery .......................................................... 5-34
Buying New Tires ........................................... 5-62
Inadvertent Power Saver .............................. 3-16
Brake
Emergencies ................................................ 4-5
System Inspection ....................................... 6-25 C
Brakes .......................................................... 5-31 California Fuel .................................................. 5-6
System Warning Light .................................. 3-31 California Perchlorate Materials Requirements ....... 5-5
Braking ........................................................... 4-3 California Proposition 65 Warning ....................... 5-4
Braking in Emergencies ..................................... 4-5 Canadian Owners ................................................ ii
2
Capacities and Specifications ............................ 5-94 Cigarette Lighter ............................................. 3-17
Carbon Monoxide ........................... 2-32, 4-13, 4-25 Cleaning
Care of Aluminum Wheels ........................................ 5-84
Safety Belts ................................................ 5-81 Exterior Lamps/Lenses ................................. 5-82
Your CD Player ........................................... 3-63 Fabric/Carpet .............................................. 5-80
Your CDs ................................................... 3-63 Finish Care ................................................. 5-82
Cargo Cover .................................................. 2-38 Instrument Panel, Vinyl, and Other Plastic
CD, MP3 ............................................... 3-54, 3-58 Surfaces ................................................. 5-81
Center High-Mounted Stoplamp (CHMSL) ........... 5-45 Interior ....................................................... 5-79
Chains, Tire ................................................... 5-67 Leather ...................................................... 5-81
Charging System Light .................................... 3-30 Tires .......................................................... 5-84
Check Underbody Maintenance ............................... 5-85
Engine Light ............................................... 3-34 Washing Your Vehicle ................................... 5-82
Checking Things Under the Hood ...................... 5-10 Weatherstrips .............................................. 5-82
Chemical Paint Spotting ................................... 5-85 Windshield and Wiper Blades ........................ 5-83
Child Restraints Climate Control System ................................... 3-19
Child Restraint Systems ............................... 1-33 Air Filter, Passenger Compartment ................. 3-23
Infants and Young Children ........................... 1-30 Outlet Adjustment ........................................ 3-22
Lower Anchors and Tethers for Children .......... 1-37 Clock ............................................................ 3-18
Older Children ............................................. 1-27 Clutch, Hydraulic ............................................. 5-18
Securing a Child Restraint in a Rear Seat Collision Damage Repair .................................. 7-10
Position .................................................. 1-45 Compact Spare Tire ........................................ 5-78
Securing a Child Restraint in the Right Front Control of a Vehicle .......................................... 4-3
Seat Position ........................................... 1-48 Convenience Net ............................................ 2-37
Where to Put the Restraint ........................... 1-36
3
Coolant
Engine Temperature Gage ............................ 3-33 D
Heater, Engine ............................................ 2-21 Daytime Running Lamps .................................. 3-13
Surge Tank Pressure Cap ............................. 5-22 Daytime Running Lamps Indicator Light ............. 3-39
Cooling System .............................................. 5-24 Defensive Driving ............................................. 4-2
Cruise Control ................................................ 3-10 Diesel
Cruise Control Light ........................................ 3-38 Running Out of Fuel .................................... 2-33
Cupholder(s) .................................................. 2-36 Disc, MP3 ............................................. 3-54, 3-58
Customer Assistance Information Doing Your Own Service Work ........................... 5-5
Courtesy Transportation .................................. 7-9 Dome Lamp ................................................... 3-15
Customer Assistance for Text Door
Telephone (TTY) Users ............................... 7-4 Ajar Light ................................................... 3-39
Customer Assistance Offices ........................... 7-5 Central Door Unlocking System ....................... 2-7
Customer Satisfaction Procedure ..................... 7-2 Door Ajar Reminder ....................................... 2-8
GM Mobility Reimbursement Program ............... 7-6 Locks .......................................................... 2-6
Reporting Safety Defects to General Motors .... 7-14 Power Door Locks ......................................... 2-7
Reporting Safety Defects to the Canadian Rear Door Security Locks ............................... 2-8
Government ............................................ 7-14 Driver
Reporting Safety Defects to the United Seat Tilt Adjuster ........................................... 1-4
States Government ................................... 7-13 Driving
Roadside Assistance Program ......................... 7-6 At Night ..................................................... 4-10
Service Publications Ordering Information ........ 7-15 Before a Long Trip ...................................... 4-11
Defensive ..................................................... 4-2
4
Driving (cont.) Engine (cont.)
Drunken ....................................................... 4-2 Drive Belt Routing ....................................... 5-96
Highway Hypnosis ....................................... 4-12 Engine Compartment Overview ...................... 5-12
Hill and Mountain Roads .............................. 4-12 Exhaust ..................................................... 2-32
In Rain and on Wet Roads ........................... 4-10 Oil ............................................................. 5-13
Rocking Your Vehicle to Get it Out ................. 4-18 Overheating ................................................ 5-22
Winter ........................................................ 4-13 Starting ...................................................... 2-19
Event Data Recorders ..................................... 7-16
Extender, Safety Belt ....................................... 1-26
E Exterior Lamps ............................................... 3-13
EDR ............................................................. 7-16
Electrical System
Add-On Equipment ...................................... 5-88 F
Engine Compartment Fuse Block ................... 5-91 Filter
Fuses and Circuit Breakers ........................... 5-89 Engine Air Cleaner ...................................... 5-16
Headlamp Wiring ......................................... 5-88 Finish Damage ............................................... 5-85
Instrument Panel Fuse Block ......................... 5-89 Flashers, Hazard Warning .................................. 3-6
Power Windows and Other Power Options ...... 5-88 Flash-to-Pass ................................................... 3-8
Windshield Wiper Fuses ............................... 5-88 Flat Tire ........................................................ 5-68
Engine Flat Tire, Changing ......................................... 5-69
Air Cleaner/Filter ......................................... 5-16 Flat Tire, Storing ............................................. 5-78
Check and Service Engine Soon Light ............ 3-34 Fluid ............................................................. 5-18
Coolant ...................................................... 5-19 Power Steering ........................................... 5-29
Coolant Heater ............................................ 2-21 Windshield Washer ...................................... 5-30
Coolant Temperature Gage ........................... 3-33 Fog Lamp
Cooling System Inspection ............................ 6-24 Fog ........................................................... 3-14
5
Fog Lamp Light .............................................. 3-38
Front Armrest Storage Area .............................. 2-36 G
Fuel ............................................................... 5-6 Gage
Additives ...................................................... 5-6 Engine Coolant Temperature ......................... 3-33
California Fuel .............................................. 5-6 Fuel .......................................................... 3-40
Filling a Portable Fuel Container .................... 5-10 Speedometer .............................................. 3-26
Filling the Tank ............................................. 5-8 Tachometer ................................................. 3-26
Fuels in Foreign Countries .............................. 5-7 Gasoline
Gage ......................................................... 3-40 Octane ........................................................ 5-6
Gasoline Octane ........................................... 5-6 Specifications ............................................... 5-6
Gasoline Specifications .................................. 5-6 Glove Box ..................................................... 2-36
Low Warning Light ....................................... 3-40 GM Mobility Reimbursement Program .................. 7-6
Running Out of ........................................... 2-33
System Inspection ....................................... 6-24
Fuses
Engine Compartment Fuse Block ................... 5-91
H
Hazard Warning Flashers ................................... 3-6
Fuses and Circuit Breakers ........................... 5-89 Head Restraints ............................................... 1-7
Instrument Panel Fuse Block ......................... 5-89 Headlamp
Windshield Wiper ......................................... 5-88 Aiming ....................................................... 5-40
Headlamp Wiring ............................................ 5-88
6
Headlamps .................................................... 5-41
Bulb Replacement ....................................... 5-40 I
Daytime Running Lamps ............................... 3-13 Ignition Positions ............................................. 2-18
Exterior Lamps ............................................ 3-13 Immobilizer .................................................... 2-16
Flash-to-Pass ............................................... 3-8 Immobilizer Operation ...................................... 2-16
Front Turn Signal and Parking Lamps ............. 5-42 Inadvertent Power Battery Saver ....................... 3-16
Halogen Bulbs ............................................ 5-40 Infants and Young Children, Restraints ............... 1-30
High/Low Beam Changer ................................ 3-8 Inflation - Tire Pressure ................................... 5-56
On Reminder .............................................. 3-13 Inspection
Sidemarker Lamps ....................................... 5-44 Brake System ............................................. 6-25
Turn Signal Lamps ...................................... 5-43 Engine Cooling System ................................ 6-24
Heater ........................................................... 3-19 Exhaust System .......................................... 6-24
Hideaway Rear Storage Bins ............................ 2-38 Fuel System ............................................... 6-24
Highbeam On Light ......................................... 3-39 Part C - Periodic Maintenance ....................... 6-24
Highway Hypnosis ........................................... 4-12 Steering, Suspension and Front Drive Axle
Hill and Mountain Roads .................................. 4-12 Boot and Seal ......................................... 6-24
Hold Mode Light ............................................. 3-33 Throttle System ........................................... 6-25
Hood Instrument Panel
Checking Things Under ................................ 5-10 Overview ..................................................... 3-4
Release ..................................................... 5-11 Instrument Panel (I/P)
Horn ............................................................... 3-6 Brightness .................................................. 3-15
How to Wear Safety Belts Properly ................... 1-15 Cluster ....................................................... 3-25
Hydraulic Clutch ............................................. 5-18 Integrated Windshield Antenna .......................... 3-63
7
J Light
Airbag Readiness ........................................ 3-27
Jump Starting ................................................. 5-35 Antilock Brake System Warning ..................... 3-32
Brake System Warning ................................. 3-31
Charging System ......................................... 3-30
K Cruise Control ............................................. 3-38
Daytime Running Lamps Indicator .................. 3-39
Keyless Entry System ....................................... 2-3
Keys ............................................................... 2-2 Door Ajar ................................................... 3-39
Fog Lamp .................................................. 3-38
Highbeam On ............................................. 3-39
L Hold Mode ................................................. 3-33
Low Fuel Warning ....................................... 3-40
Labeling, Tire Sidewall ..................................... 5-50 Malfunction Indicator .................................... 3-34
Lamps Oil Pressure ............................................... 3-38
Dome ........................................................ 3-15 Passenger Airbag Status Indicator .................. 3-28
Inadvertent Power Battery Saver .................... 3-16 Safety Belt Reminders .................................. 3-27
Map .......................................................... 3-16 Speed Sensitive Power Steering (SSPS)
Lap-Shoulder Belt ........................................... 1-23 Warning Light .......................................... 3-32
LATCH System Tire Pressure .............................................. 3-34
Child Restraints ........................................... 1-37 Trunk Ajar .................................................. 3-39
License Plate Lamps ....................................... 5-47 Lights
Liftgate Exterior Lamps ............................................ 3-13
Carbon Monoxide ........................................ 2-10 Flash-to-Pass ............................................... 3-8
High/Low Beam Changer ................................ 3-8
On Reminder .............................................. 3-13
8
Loading Your Vehicle ....................................... 4-18 Maintenance Schedule (cont.)
Lockout Protection ............................................ 2-9 Exhaust System Inspection ........................... 6-24
Locks Fuel System Inspection ................................ 6-24
Central Door Unlocking System ....................... 2-7 How This Section is Organized ....................... 6-3
Door ........................................................... 2-6 Introduction .................................................. 6-2
Lockout Protection ......................................... 2-9 Long Trip/Highway Scheduled Maintenance ..... 6-14
Power Door .................................................. 2-7 Maintenance Requirements ............................. 6-2
Rear Door Security Locks ............................... 2-8 Part A - Scheduled Maintenance Services ......... 6-4
Long Trip/Highway Scheduled Maintenance ........ 6-14 Part B - Owner Checks and Services ............. 6-19
Loss of Control ................................................ 4-8 Part C - Periodic Maintenance Inspections ...... 6-24
Low Fuel Warning Light ................................... 3-40 Part D - Recommended Fluids and Lubricants . 6-26
Luggage Carrier .............................................. 2-37 Part E - Maintenance Record ........................ 6-28
Lumbar Selecting the Right Schedule .......................... 6-5
Manual Controls ............................................ 1-4 Short Trip/City Scheduled Maintenance ............. 6-7
Steering, Suspension and Front Drive Axle
Boot and Seal Inspection .......................... 6-24
M Throttle System Inspection ............................ 6-25
Using .......................................................... 6-4
Maintenance, Replacement Parts ...................... 5-95
Your Vehicle and the Environment ................... 6-2
Maintenance Schedule
Malfunction Indicator Light ................................ 3-34
At Each Fuel Fill ......................................... 6-19
Manual Lumbar Controls .................................... 1-4
At Least Once a Month ................................ 6-19
Manual Seats ............................................ 1-2, 1-3
At Least Once a Year .................................. 6-21
Manual Transmission
At Least Twice a Year .................................. 6-20
Fluid .......................................................... 5-18
Brake System Inspection .............................. 6-25
Operation ................................................... 2-26
Engine Cooling System Inspection ................. 6-24
9
Manual, Using .................................................... iii Online Owner Center ........................................ 7-4
Manual Windows ............................................ 2-11 OnStar, Privacy .............................................. 7-17
Map Lamps .................................................... 3-16 Other Warning Devices ...................................... 3-6
Mirrors Outlet Adjustment ............................................ 3-22
Manual Rearview Mirror ................................ 2-34 Outlets
Outside Convex Mirror ................................. 2-35 Accessory Power ......................................... 3-16
Outside Heated Mirrors ................................ 2-35 Outside
Outside Manual Mirrors ................................ 2-34 Convex Mirror ............................................. 2-35
Outside Power Mirrors .................................. 2-35 Heated Mirrors ............................................ 2-35
MP3 ..................................................... 3-54, 3-58 Manual Mirrors ............................................ 2-34
MyGMLink.com ................................................ 7-4 Power Mirrors ............................................. 2-35
Owners, Canadian ............................................... ii
N
Navigation System, Privacy .............................. 7-17 P
New Vehicle Break-In ...................................... 2-17 Paint, Damage ............................................... 5-85
Park Brake .................................................... 2-28
Park (P)
O Shifting Into ................................................ 2-29
Shifting Out of ............................................ 2-30
Odometer ...................................................... 3-26
Parking
Odometer, Trip ............................................... 3-26
Over Things That Burn ................................. 2-32
Off-Road Recovery ........................................... 4-8
Parking Your Vehicle ....................................... 2-31
Oil
Part A - Scheduled Maintenance Services ............ 6-4
Engine ....................................................... 5-13
Part B - Owner Checks and Services ................ 6-19
Pressure Light ............................................. 3-38
Part C - Periodic Maintenance Inspections .......... 6-24
Older Children, Restraints ................................ 1-27
10
Part D - Recommended Fluids and Lubricants .... 6-26 Rear Door Security Locks .................................. 2-8
Part E - Maintenance Record ........................... 6-28 Rear Seat Armrest .......................................... 2-37
Passenger Airbag Status Indicator ..................... 3-28 Rear Seat Operation ......................................... 1-8
Passenger Compartment Air Filter ..................... 3-23 Rear Windshield Washer/Wiper ......................... 3-10
Passenger Sensing System .............................. 1-59 Rearview Mirrors ............................................. 2-34
Passing ........................................................... 4-8 Reclining Seatbacks .......................................... 1-5
Perchlorate Materials Requirements, California ...... 5-5 Recreational Vehicle Towing ............................. 4-23
Power Remote Keyless Entry (RKE) System .................. 2-3
Door Locks .................................................. 2-7 Remote Keyless Entry (RKE) System,
Electrical System ......................................... 5-88 Operation ..................................................... 2-4
Inadvertent Battery Saver ............................. 3-16 Removing the Flat Tire and Installing the
Steering Fluid ............................................. 5-29 Spare Tire .................................................. 5-73
Windows .................................................... 2-12 Removing the Spare Tire and Tools ................... 5-70
Privacy .......................................................... 7-16 Replacement Bulbs ......................................... 5-48
Event Data Recorders .................................. 7-16 Replacement Parts, Maintenance ...................... 5-95
Navigation System ....................................... 7-17 Reporting Safety Defects
OnStar ....................................................... 7-17 Canadian Government .................................. 7-14
Radio Frequency Identification ....................... 7-17 General Motors ........................................... 7-14
United States Government ............................ 7-13
Restraint System Check
R Checking the Restraint Systems .................... 1-66
Replacing Restraint System Parts After
Radio Frequency Identification (RFID), Privacy .... 7-17
a Crash .................................................. 1-67
Radios .......................................................... 3-41
Roadside
Care of Your CD Player ............................... 3-63
Assistance Program ....................................... 7-6
Care of Your CDs ........................................ 3-63
Rocking Your Vehicle to Get it Out .................... 4-18
Radio with CD ............................................ 3-42
Routing, Engine Drive Belt ............................... 5-96
Radio with Six-Disc CD ................................ 3-48
Running Out of Fuel ........................................ 2-33
Reception ................................................... 3-62
11
S Service (cont.)
Engine Soon Light ....................................... 3-34
Safety Belt Publications Ordering Information ................... 7-15
Reminder Light ............................................ 3-27 Service, Scheduling Appointments ....................... 7-8
Safety Belts Servicing Your Airbag-Equipped Vehicle .............. 1-64
Care of ...................................................... 5-81 Sheet Metal Damage ....................................... 5-84
How to Wear Safety Belts Properly ................ 1-15 Shifting Into Park (P) ....................................... 2-29
Lap-Shoulder Belt ........................................ 1-23 Shifting Out of Park (P) ................................... 2-30
Safety Belt Extender .................................... 1-26 Short Trip/City Scheduled Maintenance ................ 6-7
Safety Belt Use During Pregnancy ................. 1-26 Signals, Turn and Lane-Change .......................... 3-7
Safety Belts Are for Everyone ....................... 1-10 Spare Tire
Safety Warnings and Symbols .............................. iii Compact .................................................... 5-78
Seats Installing .................................................... 5-73
Driver Seat Tilt Adjuster ................................. 1-4 Removing ................................................... 5-70
Head Restraints ............................................ 1-7 Storing ....................................................... 5-78
Manual Lumbar ............................................. 1-4 Specifications, Capacities ................................. 5-94
Rear Seat Operation ...................................... 1-8 Speed Sensitive Power Steering (SSPS)
Reclining Seatbacks ...................................... 1-5 Warning Light ............................................. 3-32
Securing a Child Restraint Speedometer .................................................. 3-26
Rear Seat Position ...................................... 1-45 Starting the Engine ......................................... 2-19
Right Front Seat Position .............................. 1-48 Steering .......................................................... 4-6
Selecting the Right Schedule, Maintenance .......... 6-5 Steering, Suspension and Front Drive Axle Boot
Service ........................................................... 5-4 and Seal Inspection ..................................... 6-24
Accessories and Modifications ......................... 5-4 Steering Wheel Controls, Audio ......................... 3-61
Adding Equipment to the Outside of Your Steering Wheel, Tilt Wheel ................................. 3-6
Vehicle ..................................................... 5-5 Storage Areas ................................................ 2-36
California Pershlorate Materials Convenience Net ......................................... 2-37
Requirements ............................................ 5-5 Cupholder(s) ............................................... 2-36
California Proposition 65 Warning .................... 5-4 Front Armrest Storage Area ........................... 2-36
Doing Your Own Work ................................... 5-5 Glove Box .................................................. 2-36
12
Storage Areas (cont.) Tires ............................................................. 5-49
Hideaway Rear Storage Bins ......................... 2-38 Aluminum Wheels, Cleaning .......................... 5-84
Luggage Carrier .......................................... 2-37 Buying New Tires ........................................ 5-62
Rear Seat Armrest ....................................... 2-37 Chains ....................................................... 5-67
Sunglasses Storage Compartment .................. 2-36 Changing a Flat Tire .................................... 5-69
Stuck in Sand, Mud, Ice, or Snow ..................... 4-17 Cleaning .................................................... 5-84
Sun Visors ..................................................... 2-13 Compact Spare Tire ..................................... 5-78
Sunroof ......................................................... 2-39 Different Size .............................................. 5-64
If a Tire Goes Flat ....................................... 5-68
Inflation - Tire Pressure ................................ 5-56
T Inspection and Rotation ................................
Installing the Spare Tire ................................
5-60
5-73
Tachometer .................................................... 3-26
Pressure Monitor Operation ........................... 5-59
Taillamps
Pressure Monitor System .............................. 5-57
Stoplamps, and Back-Up Lamps .................... 5-47
Removing the Flat Tire ................................. 5-73
Turn Signal, and Stoplamps .......................... 5-46
Removing the Spare Tire and Tools ............... 5-70
Turn Signal, Stoplamps and Back-up Lamps .... 5-46
Storing a Flat or Spare Tire and Tools ............ 5-78
Theft-Deterrent System .................................... 2-14
Tire Sidewall Labeling .................................. 5-50
Theft-Deterrent Systems ................................... 2-14
Tire Terminology and Definitions .................... 5-53
Immobilizer ................................................. 2-16
Uniform Tire Quality Grading ......................... 5-64
Immobilizer Operation ................................... 2-16
Wheel Alignment and Tire Balance ................. 5-66
Throttle System Inspection ............................... 6-25
Wheel Replacement ..................................... 5-66
Tilt Adjuster, Driver Seat .................................... 1-4
When It Is Time for New Tires ...................... 5-62
Tilt Wheel ........................................................ 3-6
Towing
Time ............................................................. 3-18
Recreational Vehicle ..................................... 4-23
Tire
Towing a Trailer .......................................... 4-25
Pressure Light ............................................. 3-34
Your Vehicle ............................................... 4-23
13
Transmission
Fluid, Automatic ........................................... 5-18 W
Fluid, Manual .............................................. 5-18 Warning Lights, Gages and Indicators ................ 3-24
Transmission Operation, Automatic .................... 2-22 Warnings
Transmission Operation, Manual ........................ 2-26 Hazard Warning Flashers ............................... 3-6
Trip Odometer ................................................ 3-26 Other Warning Devices .................................. 3-6
Trunk Ajar Light .............................................. 3-39 Safety and Symbols ......................................... iii
Turn and Lane-Change Signals .......................... 3-7 Vehicle Damage .............................................. iv
Turn Signal/Multifunction Lever ........................... 3-7 Wheels
Alignment and Tire Balance .......................... 5-66
Different Size .............................................. 5-64
U Replacement ............................................... 5-66
Where to Put the Restraint ............................... 1-36
Uniform Tire Quality Grading ............................ 5-64
Using this Manual ............................................... iii Windows ....................................................... 2-11
Manual ...................................................... 2-11
Power ........................................................ 2-12
V Windshield
Washer ........................................................ 3-9
Vehicle
Washer Fluid .............................................. 5-30
Control ........................................................ 4-3
Wiper Blade Replacement ............................. 5-48
Damage Warnings ........................................... iv
Wiper Blades, Cleaning ................................ 5-83
Loading ...................................................... 4-18
Wiper Fuses ............................................... 5-88
Parking Your ............................................... 2-31
Wipers ......................................................... 3-8
Symbols ......................................................... iv
Windshield, Rear Washer/Wiper ........................ 3-10
Vehicle Data Recording and Privacy .................. 7-16
Winter Driving ................................................ 4-13
Vehicle Identification
Number (VIN) ............................................. 5-87
Service Parts Identification Label ................... 5-87
Ventilation Adjustment ...................................... 3-22 Y
Visors ........................................................... 2-13 Your Vehicle and the Environment ....................... 6-2
14

2008 Chevrolet Optra Manual en CA PDF

Uploaded by

Copyright:

Available Formats

2008 Chevrolet Optra Manual en CA PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

2008 Chevrolet Optra Manual en CA PDF

Uploaded by

Copyright:

Available Formats

2008 Chevrolet Optra Owner Manual M

Index We tell you what the hazard is and what to do to help

If your vehicle has a sliding storage tray under the front

If your vehicle does not have a sliding storage tray

The manual drivers seat tilt adjuster knobs are located

The seats have manual reclining seatbacks. The lever

Do not have a seatback reclined if your vehicle is moving.

Pull the head restraint up to raise it. To lower the

Put someone on it.

Take the simplest vehicle. Suppose it is just a seat on

A: The shoulder belt is too loose. It will not give as

A: The lap belt is too loose. It will not give nearly as

A: The belt is buckled in the wrong place.

A: The belt is over an armrest.

A: The shoulder belt is worn under the arm. It should

A: The belt is behind the body.

A: The belt is twisted across the body.

To unlatch the belt, push the button on the buckle.

6. To make the lap part tight, pull up on the

A pregnant woman should wear a lap-shoulder belt,

Older children who have outgrown booster seats should

According to accident statistics, children and infants

children, but not for young children and

Lower Anchor and Top Tether Anchor To assist you in locating

Wagon Center Position

For the center position in wagon model, the top tether

3. Push the latch plate into the buckle until it clicks.

5. To tighten the belt, push down on the child restraint,

The system checks the airbag electrical system for

The right front passengers airbag is in the instrument

Your vehicle has a feature that may automatically

A thick layer of additional material, such as a blanket

One key is used for the ignition and all locks.

Power Door Locks

See Door Ajar Light on page 3-39 for additional

Press the lockout button to stop the front and rear

Your vehicle may have a theft-deterrent system.

LOCK/OFF: This position locks the steering wheel,

ACC (ACC/ACCESSORY): This position operates

Hold Mode Functions

The parking brake lever is located between the

Outside Manual Mirrors

The passenger side mirror is convex. A convex mirrors

Cupholder(s) Front Armrest Storage Area

Your vehicle may have a cargo cover. Pull the handle of

To open the sunroof to the vent position, push the front

Uplevel shown, Base similar

Mist Function {CAUTION:

1. Press the ON/OFF button to turn on the cruise

Reducing Speed While Using Cruise Ending Cruise Control

Uplevel shown, Base similar Daytime Running Lamps (DRL)

O (Door): The light comes on while a door is opened.

Accessory Power Outlet(s)

H (Hour): To go forward one hour, press the H button

5 (Floor): This mode directs most of the air to the floor

3. Remove the old passenger compartment air filter.

1. Remove the four screws from the filter cover

Uplevel shown, Base similar

This light will come on