CLIENT

Company Name here 0

Company Address here
0 PROJECT
Tele No. 0
Fax No.
JOB NO. SUBJECT DATE BY CHECKED
0 Metal Building foundation design 23/09/08 PR

Allowable Safe Bearing

(this takes account of
foundation wt).

USE 3.42 ksf

Typical Portal Frame Bay Loads

(as provided by the Metal Fabricator, Dated 9-3-08) re-draw frame

Frame at 147/0/0 used here. to suit design

loads in kips
indicates loads

16.9 horizontal 19.2 used

19.8 base shears 14.3
Additional
uplift force uplift force User Inputted
21.8 18.7 Vertical load
38.3 37.7 DL 24

reaction force reaction force LL 28

Qu:- Do you want the additional Vertical DL to act against the uplift? YES!
F.O.S on uplift and Overturning 1.50
Design assumes self wt of Pad found & user inputed load resists Uplift!

Min Base Area, based on Bearing 26.404 ft Start with

ie a square base of length 5.2 ft 6 ft
Min Base Volume, Based on Uplift 2 ft
Min thickness of base on start value 0.056 ft ok!
Assumed max base thk'ness 2 ft
Min Area, base on a 2ft base thk'ness 1 ft TRY
ie a square base of length 1 ft 6 ft
Pressure below base based on Axial only 2.508 ksf
Qu:- Do you want the bases to resisit the column base shear moment? NO!!

Proposed Depth to underside of Pad 6.000 ft below frost line, ok!

Ht above grade for column base 0.667 ft
Horiz force at column base N/A kips founds tied @ slab RL

D/6 = 1 Stem/Peir moment induced by max ecc 7.525 kips-ft ecc = 1 inch
e = 0.08 concrete peir/stem wt 4.38 kips
Max Base Pressure 2.839 ksf OK!
Min Base Pressure 2.421 ksf
F.O.S on over turning 37.74 OK!

ADOPT 6 ft by 6 ft by 2 ft thk SHT. OF

1 4
 CLIENT

Company Name here 0

Company Address here
0 PROJECT
Tele No. 0
Fax No.
JOB NO. SUBJECT DATE BY CHECKED
0 Metal Building foundation design 23/09/08 PR

REINFORCEMENT DESIGN FOR METRIC UNITS

Plinth/Pedestal Design Area

Assume Sq
Base to be tied!

Col + Plinth Wt 4.3 m

450 mm

max 300mm into base

Plan View
Factor of Safety for design 1.5

Plinth wt kN 1.215
Horiz Shear @ base kN 0
Column Axial load kN 90.3
Max Design Axial Force kN 137.3 (factored loads)
Max Design Bending Moment kNm 11.287 (factored loads)

Plinth/Pedestal Area 0.20 m Volume 0.87075 m

max V before
Design Loads Axial force =
137.3 kN Shear critical
moment =11.3 kNm 134.1
base shear =
N/A kN Shear Not Critical
Concrete strength, fcu 35 N/mm Re-bar strength, fy 420 N/mm
Cover to main vert bar 50 mm Max/Limiting Plinth Ht 2045 mm
Min % used for design 0.4 % Design Not valid!
CALCULATIONS (only valid if design noted as OK! above)
from M As = {M - 0.67fcu.b.dc(h/2 - dc/2)}/[(h/2-d').(fsc+fst).gm] gm steel 1.05
from N As = (N - 0.67fcu.b.dc/gm) / (fsc - fst) gm conc 1.50

0.67fcu/gm 15.6 N/mm d'= 68.0 mm

fy/gm 400.0 N/mm d= 382.0 mm
from iteration, n/a depth 43.3 mm dc= 38.9 mm
0.67.fcu.b.dc/gm 274.0 kN
steel comp strain -0.002000
steel tensile strain 0.027400
steel stress in comp.face, fsc -400.1 N/mm Comp. Stress in re-bar
steel stress in tens face, fst 400.1 N/mm Tensile stress in re-bar

from M, As = -41204501 mm from N, As = 171 mm

ok but lightly loaded - see Cl 3.8.6 but use min. 0.4%,
As req'd = 405mm T&B:- PROVIDE 4X20

(ie 2X20T&B - 628mm T&B - 0.6% o/a - @ 314cc.)

where Vmax is greater than Critical Shear, more than min links are req'd, ELSE IGNORE!

cl 3.4.5.12 100As/bd from table 3.8, vc = N/mm (this includes fcu increase factor)
formula 6b vc' = N/mm v= N/mm

(v-vc')bv/0.95fyv = As/S where S is the link Crs Vert.

As Req'd mm/bar As prov 8 @ 150 Crs, 2 legs 50.3 mm/bar

Min Req'd!! Provide links of 8 mm Dia Bars @ 150 Crs Vert, ( 2 legs) SHT. OF
Plinth Design NOT VALID!! 2 4
 CLIENT

Company Name here 0

Company Address here
0 PROJECT
Tele No. 0
Fax No.
JOB NO. SUBJECT DATE BY CHECKED
0 Metal Building foundation design 23/09/08 PR

Max Stress
REINFORCEMENT DESIGN FOR METRIC UNITS
2.839

Stress @ Col Base Area 36.00 m Volume 72 m

2.614 Factor of Safety for design 1.6 Concrete Strength, fcu 35 N/mm

lever arms Max Design Bending Moment 17.03 kNm Re-bar strength, fy 420 N/mm
L1 0.925
L2 1.850 User Inputted top steel Moment 0 kNm Re-bar cover 50 mm
Is the edge beam adequatly tied for Uplift? effective depth 1930 mm

Design for a metre width of foundation (depth- cover- tens steel Bar size)
for B/M 17.03 kNm
M/bd = 0.00 for B/M 0 kNm
K=M/bdfcu, K= 0.00013 M/bd = 0.00
z max = 0.95d, 1833.50 K=M/bdfcu, K= 0.00000
K'= 0.156 z max = 0.95d 1833.5
No Comp steel req'd if K<=K', z = 1930
if K<=K', z = 1929.70 z for design = 1834
if K>K', z = 1499.40 if Tens Steel only
z for design = 1833.50 As= 0
if Tens Steel only Min Areas of steel
As= 23.30 As in the comp zone 0
if Comp steel req'd % of Concrete area 0.000%
As= 6613.6 Min % req'd 0.13% Thus
As'= -27381.5 Area of Steel 0
Min Areas of steel
ten steel area to use 23
% of Concrete area 0.001%
Area of Ten Steel 2509 Bottom Steel Req'd 2509.00 mm/m
Area of Comp Steel 0 Top Steel Req'd 0.00 mm/m

Shear Check :- 6240 mm, length lies outwith the critical shear perimeter, no check req'd
Thus, No shear check req'd the Min of 0.8fcu, or 5 = N/mm
100As/bd from table 3.8, vc = N/mm (this includes fcu increase factor)
uniform soil pressure (SL) kN/m max load on side 'only' kN
vmax = V/ud N/mm @ plinth/Pedestal edge, Perimeter, u = mm
assumed the crit per mm Area within C.P m the base area m
Average shear on C.P kN (= the diff in area * soil pressure * f.o.s)
value THUS v = shear on C.P/( crit perimeter * d) N/mm
Since < which is <

Top Steel As p= 1260 mm/m Bottom Steel

20 @ 250

### @ 250

As' p= 1260 mm/m

provide side binders 7 , 12 Dia @ 270 crs

SHT. OF
Base Design NOT VALID!! 3 4
 CLIENT

Company Name here 0

Company Address here
0 PROJECT
Tele No. 0
Fax No.
JOB NO. SUBJECT DATE BY CHECKED
0 Metal Building foundation design 23/09/08 PR

REINFORCEMENT DESIGN FOR ENGLISH UNITS

Plinth/Pedestal Design Area

Assume Sq
Base to be tied! allow as a min
the min base dim
and add 4".
Col + Plinth Wt 5 ft
2.5 ft

max 12" into base

Plan View
Factor of Safety for design 1.6

Plinth/Pedestal Wt kips 4.69

Horiz Shear @ base kips 0
Column Axial load kips 90.3
Max Design Axial Force kips 151.99 (factored loads)
Max Design Bending Moment kip-ft 12.04 (factored loads)

max V before Plinth/Pedestal Area 6.25 ft Volume 1.16 yrds

Shear Critical
Vc = 83 Design loads Axial force = 152 kips 5.00 = As prov
moment = 13 kips-ft 5.00 = A's prov
Shear Not Critical base shear = N/A kips 0.7 =
Concrete strength 4000 psi Re-bar strength 60000 psi
Cover to main vert bar 2.5 in Max/Limiting Plinth Ht 8 ft
min % used for Design 1 % d = 30.00 in d' = 3.06 in Design OK!
CALCULATIONS (only valid if design noted as OK! above) Note!
e = 12M/P = 1.03 in e' = e+d-H/2 = 12.97 in k taken as 1.0
k1 = 0.85 > 1.05-0.05f'c > 0.65 = 0.85 r = 0.3 x width
xb = 87d / (87 +fy) = 15.94 in ab =k1.xb = 13.55 in Lu = 2.1 x L
H
d d'
kips in in-kips
A's Cc = 1365.35
P (Down) Xc = 8.22 Mc = 11228.3 Cc = 0.85f'c(k1.xb.b-As)
b Cs = 283.00 Xs = 11.94 Ms = 3379.0 Cs = A's(fy-0.85f'c)
As 3582.0 T = Asfy
T = 300.00 Xt = 11.94 Mt =
e Pb = 1348.35 eb = 13.49 Mb = 18189.4
e'
As considered in
Po = 3626.00 (Hognestad Method, More Conservative than CRSI tables)
compression only
Comp Controls when (e < eb) & Tens Controls when (e > eb) Comp Controls
Pu = 2249.15 kips Compression Steel Yields
Reduction = 0.00 kips No Reduction Required
Pu = 2249.15 kips Result Accurate Capacity OK!
y = 0.00207 in/in a= 31.26 in 's = 0.00271 in/in

# 9 bars @ 6 " Crs i.e 5 E.F

where Vmax is greater than Critical Shear, more than min links are req'd, ELSE IGNORE!

ACI 318-158 s= in Vn/ = base shear / 0.75 kips

cl 11.2.1.2 for member subject to Axial Compression (simplified version) No Shear steel
Vc=2(1+Nu/2000Ag)fc'bx.d 110.86 kips Vc/2 kips
cl 11.4.6.3 Av Min = 0.75fc'(bw.s/fyt) BUT (50bw.s)/fyt
BUT in
R11.4.7 Av = (Vu-Vc).s / fyt.d in Thus Use in

Min Req'd!! Provide links of # 3 Dia Bars @ 12 Crs Vert, ( 2 legs) SHT. OF
Pedestal Design VALID! 2 4
 CLIENT

Company Name here 0

Company Address here
0 PROJECT
Tele No. 0
Fax No.
JOB NO. SUBJECT DATE BY CHECKED
0 Metal Building foundation design 23/09/08 PR

Max Stress
REINFORCEMENT DESIGN FOR ENGLISH UNITS
2.839

Stress @ Col Base Area 36.00 ft Volume 2.67 yrds

2.543 Factor of Safety for design 1.6 Concrete Strength, 4000 psi

lever arms Max Design Bending Moment 6.71 kip-ft Re-bar strength, 60000 psi
L1 0.583
L2 1.167 User Inputted top steel Moment 0 kip-ft Re-bar cover 2.5 in
Is the edge beam adequatly tied for Uplift? effective depth 20.75 in

Design for a ft width of foundation (depth- cover- tens steel Bar size)

for BM 6.71 kip-ft for BM 0.00 kip-ft

y = 0.503 y=0.503
a = 0.106 a=0.000
ar = 0.779 ar =
0.000
ab = 10.439 ab =
10.439
cb = 12.281 cb =
12.281
1 = 0.85 1 =
0.85
= 0.90 =0.90
M Conc Cap = 496 kip-ft M Conc Cap = 496 kip-ft
As req'd = 0.45 in As req'd = 0.00 in
As' req'd = 0 in Mn = Mu = N/A kip-ft
Mod ar (As') = 0.779
Mn = 53.95 kip-ft Bottom Steel Req'd 0.45 in/ft
Mn = Mu = 48.56 kip-ft Top Steel Req'd 0.00 in/ft

Base width One-Way Shear Check Two-Way Shear check

6 ft 0.25 in
Critical Section = Critical Section = 50.75 in
Critical Perimeter, b,o = 203 in
Col width Shear check as below! Shear check as below!
30 in
Critical Area = 0.125 in Tributary Area = 5184 in
d/2 = 10.375 bw = 72 in Critical Area = 2576 in
Vu = Max Stress * Critical Area Vu = Max Stress * (Trib Area - Critical Area)
= 0.75 Vu = 0.54 kips Vu = 77.99 kips
Vc = (.2.f'c.bw.d)/1000 Refer to Cl 11.11.2.1 for the min value
for 2-way Vc = 141.73 kips Vc = 799.22 kips
s = 40 SHEAR CAPACITY OK!
Bc = 1 Base Design VALID!
Top Steel Bottom Steel
As p= 0.53 in/ft

# 6 @ 10 "

# @ "

As' p= in/ft

provide side binders 2 # 4 bars 10 " crs

SHT. OF
3 4
 CLIENT

Company Name here 0

Company Address here
0 PROJECT
Tele No. 0
Fax No.
JOB NO. SUBJECT DATE BY CHECKED
0 Metal Building foundation design 23/09/08 PR
Links as below but at 2in Crs for 3.

2.5 ft Square

z
#9 bars, 5 Each Face.
2 in
Slab RL

z Ground RL

0.7 ft
#3 bars @ 12 Crs Vert (2 legs).
#0 bars @ 12 Crs Each Way.

6.00 ft
### ft

Lean Mix
Concrete to
Allowable Safe
6.00 ft Square Bearing.

#6 bars @ 10 Crs Each Way.

Pad Foundation Detail for the following Columns on Grids.

SHT. OF
4 4
 CLIENT

Company Name here 0

Company Address here
0 PROJECT
Tele No. 0
Fax No.
JOB NO. SUBJECT DATE BY CHECKED
0 Metal Building foundation design 23/09/08 PR

Allowable Safe Bearing

(this takes account of
foundation wt).

USE 3.42 ksf

Typical Portal Frame Braced Bay Loads

(as provided by the Metal Fabricator, Dated 9-3-08) re-draw frame

Frame at 119/0/0 used here. to suit design

load in kips
indicates loads

16.2 horizontal 18.5 used

19.1 base shears 13.7
Additional
uplift force uplift force User Inputted
0 20.9 11.7 22.8 Vertical load

37.1 out of plane base shear 36.5 DL 23

reaction force reaction force LL 27

out of plane Qu:- Do you want the additional Vertical DL to act against the uplift? YES!
base shear F.O.S on uplift and Overturning 1.50
Design assumes self wt of Pad found & user inputed load resists Uplift!

Min Base Area, based on Bearing 25.468 ft Start with

ie a square base of length 5.1 ft 6 ft

Min Base Volume, Based on Uplift 21 ft

Min thickness of base on start value 0.584 ft ok!
Assumed max base thk'ness 2 ft
Min Area, base on a 2ft base thk'ness 10.5 ft TRY
ie a square base of length 3.25 ft 6 ft
Pressure below base based on Axial only 2.419 ksf
Qu:- Do you want the bases to resisit the column base shear moment? NO!!
Proposed Depth to underside of Pad 6.000 ft below frost line, ok!
Ht above grade for column base 0.670 ft
Horiz force at column base N/A kips founds tied @ slab RL

D/6 = 1 Stem/Peir moment induced by max ecc 7.258 kips-ft & 0.975 kips-ft
e = 0.09 concrete peir/stem wt 1.95 kips ecc = 1 inch
Max Base Pressure 2.680 ksf OK!
Min Base Pressure 2.267 ksf
F.O.S on over turning 32.44 OK!

ADOPT 6 ft by 6 ft by 2 ft thk SHT. OF

1 4
 CLIENT

Company Name here 0

Company Address here
0 PROJECT
Tele No. 0
Fax No.
JOB NO. SUBJECT DATE BY CHECKED
0 Metal Building foundation design 23/09/08 PR

REINFORCEMENT DESIGN FOR METRIC UNITS

Plinth/Pedestal Design Area

Assume Sq
Base to be tied!

Col + Plinth Wt 4.3 m

450 mm

max 300mm into base

Plan View
Factor of Safety for design 1.5

Plinth wt kN 1.215
Horiz Shear @ base kN 0
Column Axial load kN 87.1
Max Design Axial Force kN 132.5 (factored loads)
Max Design Bending Moment kNm 10.887 (factored loads)

Plinth/Pedestal Area 0.20 m Volume 0.87075 m

max V before
Design Loads Axial force =
132.5 kN Shear critical
moment =10.9 kNm 132.7
base shear =
N/A kN Shear Not Critical
Concrete strength, fcu 35 N/mm Re-bar strength, fy 420 N/mm
Cover to main vert bar 50 mm Max/Limiting Plinth Ht 2045 mm
Min % used for design 0.4 % Design Not valid!
CALCULATIONS (only valid if design noted as OK! above)
from M As = {M - 0.67fcu.b.dc(h/2 - dc/2)}/[(h/2-d').(fsc+fst).gm] gm steel 1.05
from N As = (N - 0.67fcu.b.dc/gm) / (fsc - fst) gm conc 1.50

0.67fcu/gm 15.6 N/mm d'= 68.0 mm

fy/gm 400.0 N/mm d= 382.0 mm
from iteration, n/a depth 43.3 mm dc= 38.9 mm
0.67.fcu.b.dc/gm 274.0 kN
steel comp strain -0.002000
steel tensile strain 0.027400
steel stress in comp.face, fsc -400.1 N/mm Comp. Stress in re-bar
steel stress in tens face, fst 400.1 N/mm Tensile stress in re-bar

from M, As = -41570712 mm from N, As = 177 mm

ok but lightly loaded - see Cl 3.8.6 but use min. 0.4%,
As req'd = 405mm T&B:- PROVIDE 4X20

(ie 2X20T&B - 628mm T&B - 0.6% o/a - @ 314cc.)

where Vmax is greater than Critical Shear, more than min links are req'd, ELSE IGNORE!

cl 3.4.5.12 100As/bd from table 3.8, vc = N/mm (this includes fcu increase factor)
formula 6b vc' = N/mm v= N/mm

(v-vc')bv/0.95fyv = As/S where S is the link Crs Vert.

As Req'd mm/bar As prov 8 @ 150 Crs, 2 legs 50.3 mm/bar

Min Req'd!! Provide links of 8 mm Dia Bars @ 150 Crs Vert, ( 2 legs) SHT. OF
Plinth Design NOT VALID!! 2 4
 CLIENT

Company Name here 0

Company Address here
0 PROJECT
Tele No. 0
Fax No.
JOB NO. SUBJECT DATE BY CHECKED
0 Metal Building foundation design 23/09/08 PR

Max Stress
REINFORCEMENT DESIGN FOR METRIC UNITS
2.680

Stress @ Col Base Area 36.00 m Volume 72 m

2.458 Factor of Safety for design 1.6 Concrete Strength, fcu 35 N/mm

lever arms Max Design Bending Moment 16.05 kNm Re-bar strength, fy 420 N/mm
L1 0.925
L2 1.850 User Inputted top steel Moment 0 kNm Re-bar cover 50 mm
Is the edge beam adequatly tied for Uplift? effective depth 1930 mm

Design for a metre width of foundation (depth- cover- tens steel Bar size)
for B/M 16.05 kNm
M/bd = 0.00 for B/M 0 kNm
K=M/bdfcu, K= 0.00012 M/bd = 0.00
z max = 0.95d, 1833.50 K=M/bdfcu, K= 0.00000
K'= 0.156 z max = 0.95d 1833.5
No Comp steel req'd if K<=K', z = 1930
if K<=K', z = 1929.70 z for design = 1834
if K>K', z = 1499.40 if Tens Steel only
z for design = 1833.50 As= 0
if Tens Steel only Min Areas of steel
As= 21.90 As in the comp zone 0
if Comp steel req'd % of Concrete area 0.000%
As= 6612.3 Min % req'd 0.13% Thus
As'= -27382.8 Area of Steel 0
Min Areas of steel
ten steel area to use 22
% of Concrete area 0.001%
Area of Ten Steel 2509 Bottom Steel Req'd 2509.00 mm/m
Area of Comp Steel 0 Top Steel Req'd 0.00 mm/m

Shear Check :- 6240 mm, length lies outwith the critical shear perimeter, no check req'd
Thus, No shear check req'd the Min of 0.8fcu, or 5 = N/mm
100As/bd from table 3.8, vc = N/mm (this includes fcu increase factor)
uniform soil pressure (SL) kN/m max load on side 'only' kN
vmax = V/ud N/mm @ plinth/Pedestal edge, Perimeter, u = mm
assumed the crit per mm Area within C.P m the base area m
Average shear on C.P kN (= the diff in area * soil pressure * f.o.s)
value THUS v = shear on C.P/( crit perimeter * d) N/mm
Since < which is <

Top Steel As p= 1260 mm/m Bottom Steel

20 @ 250

### @ 250

As' p= 1260 mm/m

provide side binders 7 , 12 Dia @ 270 crs

SHT. OF
Base Design NOT VALID!! 3 4
 CLIENT

Company Name here 0

Company Address here
0 PROJECT
Tele No. 0
Fax No.
JOB NO. SUBJECT DATE BY CHECKED
0 Metal Building foundation design 23/09/08 PR

REINFORCEMENT DESIGN FOR ENGLISH UNITS

Plinth/Pedestal Design Area

Assume Sq
Base to be tied! allow as a min
the min base dim
and add 4".
Col + Plinth Wt 5 ft
1.67 ft

max 12" into base

Plan View
Factor of Safety for design 1.6

Plinth/Pedestal Wt kips 2.1

Horiz Shear @ base kips 0
Column Axial load kips 87.1
Max Design Axial Force kips 142.72 (factored loads)
Max Design Bending Moment kip-ft 11.613 (factored loads)

max V before Plinth/Pedestal Area 2.79 ft Volume 0.52 yrds

Shear Critical
Vc = 38 Design loads Axial force = 143 kips 1.20 = As prov
moment = 12 kips-ft 1.20 = A's prov
Shear Not Critical base shear = N/A kips 0.7 =
Concrete strength 4000 psi Re-bar strength 60000 psi
Cover to main vert bar 2.5 in Max/Limiting Plinth Ht 5 ft
min % used for Design 0.5 % d = 20.04 in d' = 2.94 in Design OK!
CALCULATIONS (only valid if design noted as OK! above) Note!
e = 12M/P = 1.01 in e' = e+d-H/2 = 8.09 in k taken as 1.0
k1 = 0.85 > 1.05-0.05f'c > 0.65 = 0.85 r = 0.3 x width
xb = 87d / (87 +fy) = 10.12 in ab =k1.xb = 8.60 in Lu = 2.1 x L
H
d d'
kips in in-kips
P (Down)Cc = 582.05 Xc = 5.72 Mc = 3328.6 Cc = 0.85f'c(k1.xb.b-As)
A's
b Cs = 67.92 Xs = 7.08 Ms = 480.9 Cs = A's(fy-0.85f'c)
As T = 72.00 Xt = 7.08 Mt = 509.8 T = Asfy
e Pb = 577.97 eb = 7.47 Mb = 4319.3
e' Po = 1501.29 (Hognestad Method, More Conservative than CRSI tables)
As considered in
compression only Comp Controls when (e < eb) & Tens Controls when (e > eb) Comp Controls
Pu = 864.75 kips Compression Steel Yields
Reduction = 0.00 kips No Reduction Required
Pu = 864.75 kips Result Accurate Capacity OK!
y = 0.00207 in/in a= 17.89 in 's = 0.00251 in/in

# 7 bars @ ### " Crs i.e 2 E.F

where Vmax is greater than Critical Shear, more than min links are req'd, ELSE IGNORE!

ACI 318-158 s= in Vn/ = base shear / 0.75 kips

cl 11.2.1.2 for member subject to Axial Compression (simplified version) No Shear steel
Vc=2(1+Nu/2000Ag)fc'bx.d 51.05 kips Vc/2 kips
cl 11.4.6.3 Av Min = 0.75fc'(bw.s/fyt) BUT (50bw.s)/fyt
BUT in
R11.4.7 Av = (Vu-Vc).s / fyt.d in Thus Use in

Min Req'd!! Provide links of # 3 Dia Bars @ 12 Crs Vert, ( 2 legs) SHT. OF
Pedestal Design VALID! 2 4
 CLIENT

Company Name here 0

Company Address here
0 PROJECT
Tele No. 0
Fax No.
JOB NO. SUBJECT DATE BY CHECKED
0 Metal Building foundation design 23/09/08 PR

Max Stress
REINFORCEMENT DESIGN FOR ENGLISH UNITS
2.680

Stress @ Col Base Area 36.00 ft Volume 2.67 yrds

2.416 Factor of Safety for design 1.6 Concrete Strength, 4000 psi

lever arms Max Design Bending Moment 9.72 kip-ft Re-bar strength, 60000 psi
L1 0.722
L2 1.443 User Inputted top steel Moment 0 kip-ft Re-bar cover 2.5 in
Is the edge beam adequatly tied for Uplift? effective depth 20.625 in

Design for a ft width of foundation (depth- cover- tens steel Bar size)

for BM 9.72 kip-ft for BM 0.00 kip-ft

y = 0.503 y=0.503
a = 0.155 a=0.000
ar = 0.882 ar =
0.000
ab = 10.376 ab =
10.376
cb = 12.207 cb =
12.207
1 = 0.85 1 =
0.85
= 0.90 =0.90
M Conc Cap = 490 kip-ft M Conc Cap = 490 kip-ft
As req'd = 0.45 in As req'd = 0.00 in
As' req'd = 0 in Mn = Mu = N/A kip-ft
Mod ar (As') = 0.882
Mn = 60.55 kip-ft Bottom Steel Req'd 0.45 in/ft
Mn = Mu = 54.50 kip-ft Top Steel Req'd 0.00 in/ft

Base width One-Way Shear Check Two-Way Shear check

6 ft 5.355 in
Critical Section = Critical Section = 40.665 in
Critical Perimeter, b,o = 162.66 in
Col width Shear check as below! Shear check as below!
20.04 in
Critical Area = 2.678 in Tributary Area = 5184 in
d/2 = 10.313 bw = 72 in Critical Area = 1654 in
Vu = Max Stress * Critical Area Vu = Max Stress * (Trib Area - Critical Area)
= 0.75 Vu = 10.92 kips Vu = 99.95 kips
Vc = (.2.f'c.bw.d)/1000 Refer to Cl 11.11.2.1 for the min value
for 2-way Vc = 140.88 kips Vc = 636.54 kips
s = 40 SHEAR CAPACITY OK!
Bc = 1 Base Design VALID!
Top Steel Bottom Steel
As p= 0.6 in/ft

# 7 @ 12 "

# @ "

As' p= in/ft

provide side binders 2 # 4 bars 10 " crs

SHT. OF
3 4
 CLIENT

Company Name here 0

Company Address here
0 PROJECT
Tele No. 0
Fax No.
JOB NO. SUBJECT DATE BY CHECKED
0 Metal Building foundation design 23/09/08 PR
Links as below but at 2in Crs for 3.

1.67 ft Square

z
#7 bars, 2 Each Face.
2 in
Slab RL

Ground RL
z

0.7 ft
#3 bars @ 12 Crs Vert (2 legs).
#0 bars @ 10 Crs Each Way.

6.00 ft
### ft

Lean Mix
Concrete to
Allowable Safe
6.00 ft Square Bearing.

#7 bars @ 12 Crs Each Way.

Pad Foundation Detail for the following Columns on Grids.

SHT. OF
4 4