Scribd
Upload
596 views

Source System Connection After ECC Refresh

The document provides steps for refreshing an existing non-productive source system by copying the productive source system, including deleting copied source system assignments, renaming the target system and converting logical system names, and performing BW-specific adaptations like restoring the source system connection and repairing the delta queue.

Uploaded by

khan
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
596 views

Source System Connection After ECC Refresh

The document provides steps for refreshing an existing non-productive source system by copying the productive source system, including deleting copied source system assignments, renaming the target system and converting logical system names, and performing BW-specific adaptations like restoring the source system connection and repairing the delta queue.

Uploaded by

khan
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 9

Source system connection after ECC refresh

Created logical system for EQ1-330, dont need it run bdls directly

Note 886102
===================================================
==================
Scenario C3

You want to copy a single source system of a BW system; the BW system is not
copied. You want to refresh an existing non-productive source system (of a non-
productive BW system) by copying the productive source system [PRD to NPS,
refresh].

Phase 6: Final Activities in Target Environment

Step 6.4: Delete copied source system assignments


Directly after the copy, there is a connection between the copied SAP source system
and the original (productive) BW. Delete the source system connections of the copied
SAP source system without changing the source system connections between the
original BW and SAP source system connection by executing following procedure:

Check table RSBASIDOC in the newly copied target SAP source system to determine
all existing source system connections.

If the table is empty, you do not have to execute function module


RSAP_BIW_DISCONNECT.

If entries exist, note down all these entries: fields RLOGSYS and SLOGSYS.

Note: Do not delete the RFC destination between the target SAP source system and
the productive BW system! The system needs the destination during the deletion to
obtain metadata information from the productive BW system (only a read access).

Execute function module RSAP_BIW_DISCONNECT in the copied target SAP source


system using the following parameters:

I_BIW_LOGSYS = <RLOGSYS>

I_OLTP_LOGSYS = <SLOGSYS>

I_FORCE_DELETE = 'X'

This step deletes all obsolete BW connections. Repeat this step for all entries in table
RSBASIDOC.

Caution: DO NOT enter a value in the field "RFC target sys". This would cause the
function module to run in the system specified there!

In the copied source system: Delete all obsolete RFC destinations pointing to the
original environment.

Step 6.7: Rename the target SAP source system and convert the logical
system names
Assign the name assigned to the overwritten SAP source system (logical system
name, table T000) to the target SAP source system. Use transaction BDLS to convert
the logical system name in all the relevant tables. No other activities can be
performed in the system during conversion.
Read Notes 121163 and 369758 for details about transaction BDLS.

Step 6.8: Perform BW-specific adaptations


Restore the source system connection in the BW system connected to the overwritten
SAP source system
Start the Administrator Workbench / Data Warehousing Workbench (RSA1), right
mouse click on the source system, and choose Restore.

Repair the delta queue


In the BW system: Execute report RSSM_OLTP_INIT_DELTA_UPDATE for each
datasource, which has an active init request. Provide the field 'ALWAYS' with value 'X'.
This will push the init / delta information of the BW into the source system, thus
allows to continue loading delta or to do a new init.

===================================================
==================

SE16

RSBASIDOC
Restore
Define source system in rsa1 and again restore
Activate
Then
It came to
Took back

Taking lot of time approx 10-20 mins adapter activation

BI done

You might also like