Specification for Installation of SCG SmartBOARD Installation Manual for Fiber Cement

Board
Caution SCG SmartBOARD Non Asbestos
Do not use as any building's structure or other purposes. The installation shall follow the Installation Manual and use only the standard equipments made
by producer.

Do not eat avoid the smelling.

Attention to avoid danger

The Products of SCG SmartBOARD are designed, while the operation methods are specified to suit with the working condition in Thailand only.
Any application outside Thailand is considered to be direct responsibility of the designer, construction supervisor, and installer.
For Designer
All properties shown in this document are the average values from the testing of products which are in accordance with the specified standards by sampling
the products during period before the product distribution. Any transportation, application, or any procedures
relating to the products such as exposing the products to the sunshine or submerging in water in long period shall result in altering of product properties.
Specifications for any installation are only the basic recommendation for general application. The Method for Installation and applied structure shall
consider from the standard code of building in such country, and shall be direct responsibility of designer and supervisor.
Application of product which is not specified in the Installation Manual shall be direct responsibility of designer and construction supervisor.
For Installer and User
Specifications for any installation are only the basic recommendation for general application. The Method for Installation and applied structure shall
consider from the standard code of building in such country, and shall be direct responsibility of designer and supervisor.
Application of product which is not specified in the Installation Manual shall be consulted with the architect or designer engineer.

Recommendation for Safety Operation

SCG SmartBOARD has composed by the silica. Cutting, grinding, drilling, or polishing of the product shall result in flying dust. If any person accidentally
eat or inhale in a considerable amount or in long period it shall harm the respiratory system or body of that person.
The cutting, grinding, drilling, or polishing of the product shall carried out in good ventilated area, and avoid to use the machine for cutting, grinding, drilling,
or polishing of the product which resulting in high amount of dust.
Wear the Personal Safty Equipment which is in accordance to the standards, such as dust protection mask, safety goggle, clothes, glove, shoes etc.
Not allow any person who does not wear the Personal Protection Equipment which is in accordance to the standards, or any person who is not
concerning with the work into working area in order to avoid any possible accident or injury.
Lifting or transportation of products shall be carried out with special attention. Do not bend down ones back to lift the product nor twist oneself or change
direction during lifting, and avoid working continuously in long period in order to avoid injury and fatigue.
The person who has to perform lifting must carry out by lowing oneself and hold the products firmly, then apply legs power to lift.
Cleaning of the working area after complete the cutting, grinding, drilling, or polishing of the product shall be carried out by vacuum machine, then the
dust container shall be sealed completely, or cleaned by water. Do not sweep because this can cause spreading of dust.
Separate and collect the debris occurred from installation, reparation, dismantle of products with special attention, and eradicate with appropriate methods
which specified by government service.
Clean oneself body with clean water after complete the cutting, grinding, drilling, or polishing of the product.

First Aid
If the dust or any material debris accidentally entered the eye, do not scrub or crush. Clean with clean water several times, and consult the physician
immediately.

Verify that all methods are following the most update of Installation Manual of Products
Installation Manual of Products is always updated. The designer, construction supervisor, and installer shall verify that all methods being used are following
the most update of Installation Manual of Products. They can confirm by the website : www.siamfibrecement.com

0710
 SCG SmartBOARD fiber cement board
SCG SmartBOARD is a new generation of fiber cement material with Technology made the
board gain strength, durability and elasticity in one time. SCG SmartBOARD, with state-of-the-art composition of Recommendation on lifting and moving
Elephant (SCG) Portland Cement, Silica and Special cellulose fiber through Autoclave process, is specifically designed
Lifting or moving of products shall be carried out with
for various ceiling, wall and flooring applications both internal and external usage.
special attention and avoid continuous work in long period
SCG SmartBOARD Ceiling in order to prevent the injury or fatigue. The operator shall
Special Properties
drop oneself on knee and firmly hold the product every
High impact strength from state-of-the-art composition of Elephant (SCG) Portland time that perform the lifting. Then use his leg power to lift
High impact strength
Squared Cement, Silica and Special cellulose developed by our laboratory.
3.5, 4, 6 by holding at 30 cm. distance from the edge of
Water-Resistance and Long lasting even using in hot, humid, and strong raining weather condition SCG SmartBOARD
NEW Non-decay according to JIS Standard A5420.
4-side T
Premium

Termite Resistance Termite resistance from Portland cement material.

4-side T
6 mm. t Bendable. No water is needed to applied while bending the board. Storing Tips Personal Safety Equipment

Flexibility for Should be stored in-door with dry

various designs R = 4.0 m leveled floor on a pallet or 1.5 x 3 inches
R = 2.0 m
R = 1.5 m
R= 1.0 m
wood laid with a span of 60 cm.
Cover with water and dust proof canvas
4 mm. 6 mm. 8 mm. 10 mm.
Wood G
1 m. bending radius 1.50 m. bending radius 2.0 m. bending radius 4.0 m. bending radius Glove Clothes Safty goggle
4 mm. th

With only 30 kg. per sq.m. total weight of internal partition and faster installation than
Light weight, fast and
NEW conventional system, it provides flexibility of designs and durability of applications
easy to install
3-inch S better than conventional systems.
4 mm. th
With specially low heat conductivity compared to typical light - weight ceiling and Dust protection Mask
Support with 1.5 x 3 inches wood Safty Shoes
Better heat resistance wall material, SCG SmartBOARD is the ideal material for preventing heat from in every 60 cm. or a pallet
external environment, reducing energy consumption and answering green designs.

Ventilate Choosing SCG SmartBOARD to match your application SCG SmartBOARD Product Series
4 mm. th
Series
Installation Recommended SCG SmartBOARD Thickness (mm.) Width x Length (mm.) Weight (kg./pc.) Effective Area (sq.m.)
Application Usage area Series Surface System Thickness
Squared Edge Tapered Edge
Ventilate Space Lining, T-Bar, 603 x 1213 - 3.6 0.73
4 mm. th
Any room that you want to prevent Squared Edge Smooth Surface No Space Lining 3.2, 3.5, 4, 6 mm. 3.2 610 x 1220 (2'x4') - 3.6 0.74
problem from termites and moisture, 1220 x 1220 (4'x4') - 7.2 1.49
NEW
Internal Ceiling 4-side Tapered Edge Smooth Surface Concealed Edge 6 mm.
for example: Bathroom, Kitchen, 600 x 2400 - 7.6 1.44
Space Lining, T-Bar,
Storage room, etc. Wood Grain Wood Grain Texture No Space Lining 4 mm. Lite 1200 x 1200 - 7.6 1.44
Ventilate Squared Edge Smooth Surface
Space Lining,
3.5, 4, 6 mm. 1200 x 2400 - 15.2 2.88
No Space Lining
4 mm. th 3.5 603 x 1210 - 3.9 0.73
Ventilated Smooth Surface 610 x 1220 (2'x4') - 4.0 0.74
Space Lining,
Ventilated
No Space Lining 4 mm. 1220 x 1220 (4'x4') - 7.9 1.49
Areas where regularly expose to Wood Grain Wood Grain Texture Ventilated 1220 x 2400 (4'x8') - 15.8 2.97
SCG SmartBOARD Wall External Ceiling Rain and Sun. hole 600 x 1200 - 4.4 0.72
3-inch Square Lining - Smooth Surface Space Lining, 600 x 2400 - 8.7 1.44
Smooth Surface 1. House/Building Roof Overhang Ceiling No Space Lining 4 mm.
Wood Grain - 3-inch Lining Smooth Surface
2. House/Building Terrace 1200 x 1200 - 8.7 1.44
3. Garage, Open Cabin or Cottage 4 1200 x 2400 - 17.4 2.88
- Wood Grain Texture
Square Wood Grain Space Lining 4 mm. 610 x 610 (2'x2') - 2.3 0.37
8, 10, 1 - 3-inch Lining Smooth Surface
1220 x 1220 (4'x4') - 9.0 1.49
- Smooth Surface
1220 x 2400 (4'x8') - 18.0 2.97
Space Lining,
3-inch Square Lining No Space Lining 4 mm. 4.5 1220 x 2400 (4'x8') - 20.2 2.97
- 3-inch Lining Smooth Surface
2-side T 1200 x 2400 - 26.1 2.88
6
8 mm. t Areas where you want light weight wall Squared Edge Smooth Surface
Space Lining,
8 - 12 mm. 1220 x 2440 (4'x8') - 27.0 2.97
No Space Lining
to replace brick walls without beam 1200 x 2400 - 34.8 2.88
reinforcement needed 2-side Tapered Edge Smooth Surface Concealed Edge 8 mm. 8 1200 x 2800 - 40.2 3.36
Light Weight Wall - Durable and High resitant to Impact Squred Edge
1220 x 2440 (4'x8') - 36.0 2.97
Wood Grain/Square Lining - Easy to customize siding designs to - Smooth Surface
4-inch Square Lining No Space Lining 8 mm.
9
1200 x 2400 - 39.2 2.88
maximize individual needs - 4-inch Lining Smooth Surface
1220 x 2440 (4'x8') - 40.0 2.97
- Fast and Easy to Install
- Safe from termites Squared Edge 6-inch Lining with Golden Teak Wood Grain No Space Lining 8 mm. 10 1200 x 2400 - 43.5 2.88
6-inch 1220 x 2440 (4'x8') - 44.9 2.97
Square L
Wood Gr For decorating new built or renovating Space Lining 12
1200 x 2400 - 52.2 2.88
(Golden T Decorative Wall existing wall
Squared Edge 6-inch Lining with Golden Teak Wood Grain
6 mm.
6 mm. 1220 x 2440 (4'x8') - 53.9 2.97
6*, 8 mm 1200 x 2400 - 69.6 2.88
Space Lining
16 1200 x 3000 - 87.0 3.60
4-inch S
For permanent external wall that needs to Squared Edge Smooth Surface 8 - 16 mm. 1220 x 2440 (4'x8') - 72.0 2.97
be expose to sun, rain and wind regularly 8 - 16 mm..
8 mm. th External Wall 18
1200 x 2400 - 78.3 2.88
to replace brick walls because faster 1220 x 2440 (4'x8') - 81.0 2.97
Space Lining
installation, time saving and cost saving. Squared Edge 6-inch Lining with Golden Teak Wood Grain 8 mm.
5.5 1200 x 2400 4 side 24.0 2.88
8 mm.
6
1200 x 2400 4 side 25.8 2.88
* not recommended for structural materials. Suitable for kitchen or bathroom walls Tapered Edge 1220 x 2440 (4'x8') 2 side 26.7 2.97
Backer Board with ceramic tiles finishing which will be Squared Edge Smooth Surface No Space Lining 8 - 16 mm. 8 1200 x 2800 2 side 40.2 3.36
SCG SmartBOARD Floor resistant to impact, termite and moist. 12 1220 x 2440 (4'x8') 2 side 53.6 2.97
Smooth Surface 600 x 2400 - 7.1 1.44
Timber Texture 4 1200 x 1200 - 7.6 1.44
Underlaying for parquet and laminated Space Lining 1200 x 2400 - 15.2 2.88
NEW Floor Underlay Squared Edge Smooth Surface 8 - 12 mm.
floor to reduce time, labour, and cost. 8 - 12 mm. Wood Grain, 3-Inch Lining, Ventilated,
4 600 x 1200 - 5.0 0.72
Ventilated Wood Grain, Ventilated 3-Inch Lining
16, 6-inch Square Lining Wood Grain (Golden Teak Color)
6 600 x 3000 - 11.2 1.80
For internal and external floor which are 8 600 x 3000 - 15.0 1.80
Floor not always soaked in water.
Squared Edge Smooth Surface No Space Lining 16 - 18 mm.
4-inch Square Lining 8 1200 x 2800 - 40.0 3.36
 Content

SCG SmartBOARD Equipment for Installation

Tools and Equipment 1
SCG Self Drilling Point Screw 10 mm. SCG Needle Point Screw 23 mm.
Used to fix SCG SmartBOARD C 74 and U 76 Galvanize Specially designed to suit with the work operated with Fiber cement
Frame, or fix SCG SmartBOARD C 74 and C 74 Galvanize
Frame in order to make as door or window frames.
material safely, endure, and nice.
Longer life for rust or corrosion, because the material is made from
SCG SmartBOARD Cutting and Drilling 2
Easily install, can drill and fix firmly with two or three layers high-quality steel wires, can be used either external or internal.
of 0.55 mm. thick of steel ceiling frames. Designed to provide the fin around the screw head which make the
Endure to the rust or corrosion because
the material is made from high-quality
screw head fully embedded in the panel automatically resulting nice
surface of work.
1 Ceilling Installation 3
steel wires, can be used either external
or internal.
Containing size : 500 pieces / box 1.1 Space Lining Ceiling Installation with Wooden Frame 3
Containing size : 500 pieces / box 1.2 Space Lining Ceiling Installation with Metal Frame 4
1.3 Concealed Ceiling Installation 5
SCG Self Drilling Wing Screw 32 mm. SCG SmartBOARD polyurethane joint sealant
1.4 T - Bar Ceiling Installation 7
Specially designed to suit with the work operated with Fiber cement This is the polyurethane material used to seal the joint, easily used,
material safely, endure, and nice. and perfectly adhere to the surface of SCG SmartBOARD or 1.5 Curved Surface Installation 8
Longer life for rust or corrosion, because the material is made from any construction materials such as fiber cement, concrete,
high-quality steel wires, can be used either external or internal. brick, roof tile, ceramic tile, aluminium, timber, glass.
Specially designed to provide special drill end, which will not require Used as a joint sealant which can well prevent the leakage,
advance penetration, easily operated, and can drill rapidly into the steel, can be used in either external or internal of building. 2 Wall Installation 9
its fin can core the panel allowing the screw head to be perfectly and Endure to the climate circumstance, and can be painted
nicely embedded into the panel. The fin over without altering the color shade. 2.1 Space Lining External Wall Installation 9
will automatically break whenever the Containing size : 310 ml. / tube,
steel is eventually penetrated. and 600 ml. / foil tube 2.2 Space Lining Internal Wall Installation 11
Containing size : 500 pieces / box
2.3 Concealed Wall Installation 14
SCG SmartBOARD Acrylic Joint Compound SCG SmartBOARD Plaster Joint Compound 2.4 Bended Wall Installation 15
This is joint-plastering material made by already mixed high-quality This is ready-usable plaster cement for joint plastering especially
acrylic. It is prompt to used for plastering the joint of SCG SmartBOARD, made for SCG SmartBOARD. The cement
or other fiber cement panel inside the building. matrix is viscous resulting into smooth
Viscous acrylic matrix, smoothly plastered, plastering surface, easily mixed, no shrinkage,
3 Floor Installation 16
and the surface can be furnished easily while crack, peeling because the material provide
exposing nice plastering or coated panting. high adhesive and can be easily furnished by
Suit with ceiling work. sandpaper.
Containing size : 5 kg. / box Suit with wall work.
4 Underlay Installation 19
Containing size : 25 kg. / bag

5 Fixing and Hanging objects 20

SCG SmartBOARD C 74, U 76 Galvanize Frame 5.1 Fixing and Hanging Objects 20
Thick steel material providing strength, safety, and manufactured in accordance with 5.2 SCG SmartBOARD Maintenance 21
TIS.863-2532 with full thickness of 0.55 mm.
Economic section with 45, 47 mm. width frame section, which will not require to make
the support for the frame in the joint area between SCG SmartBOARD panel, and will reduce
the time and labor for installation. The material is endured for corrosion or rust, and the surface 6 Placing Ceramic Tiles on SCG SmartBOARD 22
is coated by Hot Dip Galvanized Steel Z22.
Coated by specially thick surface to prevent rust or corrosion.

SCG SmartBOARD Equipment for Installation 23

23
 Tools and Equipment 6. Placing Ceramic Tiles on SmartBOARD
Frames and Accessories
Leveled Equipment Drill, Cut, Drive, Hold Equipment
Fixing tool : Tile adhesive cement (flexible type)
SCG SmartBOARD : Squared Edge with 10 - 12 mm. thick.

Installation Instruction
SCG Needle Point Screw SCG Self Drilling Screw
1 40 cm.
2
40 cm.
40 cm. 40 cm.
Tape measure Net Chalk liner

SCG Self Drilling Wing Screw SCG Butterfly-wing plastic hook

For SCG SmartBOARD that is going to be attached the Prepare the surface of SCG SmartBOARD by cleaning
Plummet Level Measurement tile, leave 40 cm. gap between studs in order to prevent and applying primer, then leave it dry.
vibration during ceramic installing.
Drilling Machine Hammer

Metal Frame 3 4

Cutter
Electric Fiber cutter
(for 4 mm. thickness)

Patching Material and Equipment

Mix Tile Adhesive Cement (flexible type) as advised in Use the trowel to spread Tile Adhesive Cement (flexible
Galvanized iron metal Galvanized iron metal the manual. type) on all area of SCG SmartBOARD.
frame for T-Bar ceiling ceiling frame (C-line)

5 6

SCG SmartBOARD SCG SmartBOARD SCG SmartBOARD

polyurethane joint sealant Plaster Joint Compound Acrylic Joint Compound

Structure steel SCG SmartBOARD C74, U76

metal wall frame Galvanize Frame
After soaking tiles in the water, make it nearly dry before Place all tiles on SCG SmartBOARD (Jointing line of
Stainless trowel Stainless trowel
placing on SCG SmartBOARD. ceramic tiles must be aligned on board's jointing line).
(11-inch) (6-inch, 8-inch)
Leave it dry for 7 days for stable setting purpose. Then,
joint the gap between tiles.

Made from Siamfibrecement, Ltd.

Suggestion about placing ceramic tiles on SCG SmartBOARD
*Color of the Products in this brochure may vary slightly due to the printing system. *The information in this brochure may be modified or updated by the company without prior notice. It is our recommendation not to do it on the panel which is over 5 meters long. In such case, technical discussion in details with us is needed.

1 22
 SmartBOARD Cutting and Drilling

5.2 SCG SmartBOARD Maintenance Tools and Accessories

Frame and Accessories Cutting Tool : Electric fiber cutter (4-inch size) or cutter with 1 inch wide-blade.
Frame : C-line frame. Drilling Tool : Electric drilling machine.
Fixing Tool : SCG needle point screw 23 mm. Grinding Tool : Sandpaper, File, Grinding Machine.
Sealant Material : SCG SmartBOARD plaster joint compound, Sandpaper.

Installation Instruction Installation Instruction

In case of Minor Damage ( Less than 2 cm. crack ) To cut with electric fiber cutter : suitable for SCG SmartBOARD in every size (3.5 - 18 mm.)
1 2 1 2

Apply the cotton tape in the form of a cross and apply the After the first coat of the plaster is set, apply the second Use the electric fiber cutter (4-inch size) cut SCG Trim the edge with sandpaper.
first coat of SCG SmartBOARD plaster joint compound. coat and polish with sandpaper after it dries. SmartBOARD according to the set line.

In case of Moderate Damage ( 2 - 5 cm. crack )

1 2 3 To cut with cutter : suitable for SCG SmartBOARD 3.2 - 4 mm.
1.5 cm. 3 - 5 cm.
1 2
10 cm. 10 cm.

Cut C-line frame 10 cm. longer than the Insert the C-line frame from behind by using Apply the cotton tape in the form of a cross
crack on each side. string before drilling the SCG needle point over the crack then apply two layers of SCG Use the cutter to rip on the set line several times Lever cut SCG SmartBOARD (Don't press, or else
screw 23 mm. SmartBOARD plaster joint compound, polish until the trace is 1 of 3 deep in SCG SmartBOARD the edge will not smooth) and trim the edge with
with sandpaper, and apply coat of color. thickness. sandpaper.

In case of Major Damage ( More than 5 cm. crack )

To drill SCG SmartBOARD
1 2 3
1 2
1.5 cm. 3 - 5 cm.

Use electric saw to cut out the damage Fix the C-line frame with SCG self drilling Fix SCG SmartBOARD with SCG self drilling Drill small hole continuously with electric drilling machine Trim the edge with a file and smooth with sandpaper.
area. screw, 1.5 cm. from the edge of the crack screw. Apply the cotton tape then apply two layers according to the set line. Use the hammer knock the
and fix another screw 3 - 5 cm. to both sides. of SCG SmartBOARD plaster joint compound, unwanted piece to come off.
polish with sandpaper, and apply coat of color.

21 2
1 Ceiling Installation 5 Fixing and Hanging objects

1.1 Space Lining Ceiling Installation with Wooden Frame 5.1 Fixing and Hanging objects
Frame and accessories
Frame : Hard wood frame size 1.5 x 3 inches. Installation Instruction
Fixing Tool : SCG needle point screw 23 mm. or 1 inch nail.
Sealant Material : SCG SmartBOARD polyurethane joint sealant.
SCG SmartBOARD : Squared Edge 3.5 - 6 mm. thick. 1 2

Installation Instruction

1 2

60 cm.
Mark and Drill your desire point. Sunk butterfly - wing plastic hook into the ceiling or
wall hole.
60 cm.

3 4
Install hard wood frame size 1.5 x 3 inches. The distance Install SCG SmartBOARD. The distance between SCG
between frame is 60 x 60 cm. with straight surface, SmartBOARD is around 0.5 cm.
no twisting.

3 4

Drill the screw into the butterfly-wing plastic hook. When the screw is completely installed the butterfly-wing
plastic hook will be tightly fix with SCG SmartBOARD.

20 cm.

Suggestion : Hanging devices can be fixed to both ceiling and wall by using the following accessories.

Tight SCG SmartBOARD with SCG needle point screw For cornering, cut the SCG SmartBOARD oblique as
23 mm. or 1 inch nail, 20 cm. apart. the frame and tight with needle point screw.
Maximum Weight Stand
Product Application Accessories
(kg.)
butterfly-wing plastic hook PT - 5
5 6 SCG SmartBOARD 3.5 mm. thick Ceiling 5
with drilling screw
1.2 cm.
SCG needle point screw 23 mm.
butterfly-wing plastic hook PT - 5
SCG SmartBOARD 4 mm. thick Ceiling 7
with drilling screw

1.2 cm.
butterfly-wing plastic hook PT - 13
SCG SmartBOARD 6 mm. thick Ceiling 10
gap between screw 20 cm. with drilling screw

20 cm. butterfly-wing plastic hook PT - 13

SCG SmartBOARD 8 mm. thick Wall 80
with drilling screw

Use SCG SmartBOARD polyurethane joint sealant Apply the primer and paint with Acrylic paint twice. Recommendations 1. Use the table above to estimate the weight baring level of different thickness and usage of SCG SmartBOARD
between SCG SmartBOARD, pull the tape and leave 2. When hanging heavy weight objects, it is advised to fix your object in the position that is on the studs, the maximum weight
it dry for 7 days.
stand will also vary depending on the strength of different studs.

3 20
4 Underlay Installation
Tools and accessories 1.2 Space Lining Ceiling Installation with Metal Frame
Fixing Tool : Concrete nail 1 inch for SCG SmartBOARD 8 mm. thick.
Concrete nail 1.5 inches for SCG SmartBOARD 10 - 12 mm. thick, Frame and accessories
Glue. Frame : Hollow steel square section 2 x 3 inches, 1.2 mm. thick.
SCG SmartBOARD : Squared Edge 8 - 12 mm. thick. Fixing Tool : SCG self drilling wing screw 28.5 mm.
Sealant Material : SCG SmartBOARD polyurethane joint sealant.
Installation Instruction SCG SmartBOARD : Squared Edge 3.5 - 6 mm. thick.

1 2
Installation Instruction (Method of ceiling frame installation follow to frame producer.)

1 2

40 cm. 60 cm.
5 cm.

Prepare leveled and polished rough surface concrete Mark nailing guideline every 40 cm. and away from the 60 cm.
by let it has 7 days setting time. edge 5 cm.

Install Hollow steel square section 2 x 3 inches. The Install SCG SmartBOARD. The distance between SCG
3 4 distance between frame is 60 x 60 cm. with straight SmartBOARD is around 0.5 cm.
surface, no twisting.

3 4
1.2 cm. 1.2 cm.
SCG self drilling wing screw 28.5 mm. SCG self drilling wing screw 28.5 mm.

1.2 cm. 1.2 cm.

gap between screw 20 cm. gap between screw 20 cm.

For column cut SCG SmartBOARD to fit around the Apply Latex to entire SCG SmartBOARD. 20 cm. 20 cm.
corner.

Tight SCG SmartBOARD with SCG self drilling wing Use the tape before using SCG SmartBOARD
5 6 screw 28.5 mm., 20 cm. apart. polyurethane joint sealant for the smoother of jointing.
gap between each board 1 cm.

gap between two fixing points

is not over than 40 cm. Laminating material 5 6
1.2 cm.
Underlaying Foam SCG self drilling wing screw 28.5 mm.

gap between
the edge 2 cm. SCG SmartBOARD

Leave 5 cm. gap from

an angle of the board 1.2 cm.
gap between screw 20 cm.

Fix SCG SmartBOARD with 1" concrete nail at marked Install flooring for example Laminate, Parquet.
point and keep 1cm. away between SCG SmartBOARD 20 cm.
overlaped.

Suggestion Use SCG SmartBOARD polyurethane joint sealant Apply the primer and paint with Acrylic paint twice.
between SCG SmartBOARD, pull the tape and leave
For fixing SCG SmartBOARD with 1" concrete nail, be careful not to deepen the nail to reach reinforcing steel level.
it dry for 7 days.
Adjust the surface to be that same level before installation.
High drying shrinkage rate materials are not recommended to apply on SCG SmartBOARD.

19 4
1.3 Concealed Ceiling Installation 6 7
Frame and accessories
Frame : Galvanized iron metal ceiling frame (C-line) No. 24, minimum width of 38 mm.
Fixing Tool : SCG needle point screw 23 mm.
Face Tool : SCG SmartBOARD acrylic joint compound, Stainless trowel, Square wooden-tray,
Cotton tape, Waterproof abrasive paper.
SCG SmartBOARD : 4-side Tapered Edge 6 mm. thick.

Installation Instruction (Method of ceiling frame installation follow to frame producer.)

1 2
Fix next piece of SCG SmartBOARD together without Shape the SCG grumcrete that excesses properly and
80 cm.
space lining. fixed SCG SmartBOARD by SCG self drilling screw
40 cm. 45 mm. SCG SmartBOARD shall be installed alternately
in order to stagger the joint.

major metal studs

8
minor metal studs

Set up the metal studs to the level by lining up major In case of setting up the ceiling under the roof, use minor SCG grumcrete
metal studs no more than 80 cm. apart from each other studs at the connection point of SCG SmartBOARD, on
and minor studs 40 cm. apart. the short-sided.

SCG SmartBOARD SCG self drilling

3 4 16 / 18 mm. screw 45 mm.

steel
100 cm.

Cover the screw head by SCG grumcrete.

Check the level, make it 100 cm. apart parallel to the Stick SCG SmartBOARD into metal stud with SCG
major metal studs row. needle point screw 23 mm. along with adding minor 9
studs at the point connection on the long-sided.

5 6
away from the edge 1.2 cm

40
cm
.
20 cm.
gap between screw

Install next SCG SmartBOARD by following the above Install the surface cover material such as ceramic
method until complete, and clean all surface to be out tile, laminate, parquet, etc. (as indicated in method).
of dust and oil stain by moist cloth. In case that the surface cover material is not installed,
Fix SCG needle point screw 23 mm. away from the edge Use the corner trowel to check over the screw head clean the floor and coat by the prime coat for original
of board 1.2 cm. and 20 cm. apart from each other area before troweling. The head of the screw should cement prior coating with Epoxy twice (as suggested
separate the joint of each board. sink into SCG SmartBOARD about 1 mm. deep. by maker) in order to prevent the surface from scratching.

5 18
 Floor Installation Concealed Instruction (Only SCG SmartBOARD acrylic joint compound shall be used to plaster the joint between
SCG SmartBOARD tapered edge. All System and Opening works shall be completed prior
the plastering).
1
7 8

120 cm.

40 cm.

Check the level of steel frame and the frame spacing must not higher than that designed. 15 cm.

Clean properly, the gap between board shall be embedded Use 6" trowel to make first plastering for 15 cm. width.
2 spacing from by SCG SmartBOARD acrylic joint compound, and leave
edge 5 cm. it dry.

400 mm. spacing from

max.
edge 1.2 cm.
9 10

spacing from cotton tape

edge 1.2 cm.

Place SCG SmartBOARD 16, 18 mm. thick on steel frame and fixed by SCG self drilling screw 45 mm., with maximum 40 mm. spacing,
and 1.2 cm. distance from the edge.

3 15 cm. 20 cm.

Use 3.5 cm. width cotton tape to cover the joint, and Make second plastering by 8" trowel by plastering for
plaster over this cotton tape again, and leave it dry. 20 cm. and leave it dry.

11 12

Clean the jointing area by using a hard brush.

4 5

28 cm.

Make third plastering by 11" trowel by plastering for Polish the plastering by waterproof abrasive paper
28 cm. and leave it dry for 1 day. no.120, and paste the prime coating for original plaster
for whole ceiling board prior covered by 100% acrylic
paint for at least 2 layers.

Recommendation ;
Mix SCG grumcrete with the recommended ratio. Bring mixed SCG grumcrete to paste on the edge of SCG
SmartBOARD 16, 18 mm. thick. The concealed SCG SmartBOARD ceiling shall be installed in the area which will not directly contact to water, or the area that
tend to be vibrated by structure.

17 6
 3 Floor Installation
Frame and accessories
1.4 T-Bar Ceiling Installation
Frame : Steel.
Frame and accessories Fixing Tool : SCG self drilling screw 45 mm.
Frame : Galvanized iron metal frame T- Bar 38 mm. in height. Sealant Material : SCG grumcrete.
Fixing Tool : SCG butterfly-wing plastic hook 37 mm. , SCG needle point screw 38 mm. SCG SmartBOARD : Squared Edge 16 - 18 mm. thick.
SCG SmartBOARD : Squared Edge 3.5, 4 and 6 mm. thick, cut into 60 x 120 cm. or 60 x 60 cm.
Installation Instruction

Installation Instruction (Method of ceiling frame installation follow to frame producer.) 1. Prepare the structure to support SCG SmartBOARD flooring by allow the size and spacing of the frame to support the load safely as
designed by the Engineer, or can choose the size and spacing of the frame approximately from the table.

1 2
121 cm. Table 1 Spacing of stinger for the maximum safe load

60.5 cm. SCG SmartBOARD for flooring

major metal studs 121 cm. Distance of support Live Load
Thinkness (mm.) Type of building
minor metal studs (cm.) (kg./m2 )

Wall Angle 16 40 House / Residence 150

60 cm.

40 Hotel / Dormitory 200

Set up the metal studs to the level by lining up major Check the level, make it 121 cm. apart parallel to the
metal studs no more than 121 cm. apart from each major studs row.
other and minor studs 60.5 cm. apart. 40 Office / Bank 250

18 40 School / University 300

3 4
30 Departmentstore / Cinema / Hall / Restaurant / Carpark 400

30 Cargo / Museum / Plant / Publisher 500

Remark : SCG SmartBOARD floor shall not support point load higher than 100 kg., on 10 sq.cm. area.
Do not use in the area which always wet and moist.

2. The frame must provide at least 4.5 cm. width, in case that the steel frame is used there should be a rust protection at appropriate
level and suit to the environment and operating condition.
Cut SCG SmartBOARD into 60 x 120 cm. paint the Attach SCG SmartBOARD to prepared studs.
surface with old cement primer paint, Acrylic paint
2 times for complete cover up of the original color, 3. In case of using SCG SmartBOARD in area that longer than 6 m., all jointing spaces of SCG SmartBOARD and ceramic tiles (floor
leave it dry. covering materials) must be full-filled by SCG SmartBOARD polyurethane joint sealant.

Instruction :
In case need ceiling size 60 x 60 cm. enhance major studs 60.5 cm. in length with existing studs 121 x 60.5 cm.

7 16
 2.4 Bended Wall Installation 1.5 Curved Surface Installation
Frame and accessories Frame and accessories
Frame : SCG SmartBOARD C 74, U 76 galvanize frame. Frame : Galvanized iron metal ceiling frame (C-line) No.24
Fixing Tool : SCG self drilling screw 23 mm. Fixing Tools : SCG needle point screw 23 mm.
SCG SmartBOARD : Squared Edge 8 mm. thick. SCG SmartBOARD : Squared or Tapered Edge 4 mm. or 6 mm. thick.

Installation Instruction
Installation Instruction (Method of ceiling frame installation follow to frame producer.)
SCG SmatBOARD is flexible, so it can be bended without water soaking as follows :
1 2 attach the studs to
1 2 structural element

fix curved stud

that be bended curved studs
attach the studs to
structural element 100 cm.

Bend studs to have curve form of desired radius. Attach curved stud to structural element no more than
100 cm. apart from each.
Positioning the bended wall installation on both Set up SCG SmartBOARD U 76 galvanize frame on the
ceiling and floor floor and the ceiling with 5 - 10 cm. apart from each other
with the concrete hook at every 30 cm.

3 4
drive screw into major studs
3 4
attach SmartBOARD
hook for connection no more than 40 cm. to prepared studs

75 mm.
45 mm. no more than 40 cm.

no more than 20 cm.

cut flank, curved C-line No.24 apart from each other.
20 cm.
fix minor studs to major studs no more than 40 cm. Attach SCG SmartBOARD to minor studs by SCG
apart. needle point screw 23 mm. length, 20 cm. apart from
Set up SCG SmartBOARD C 74 galvanize frame as Attach SCG SmartBOARD to SCG SmartBOARD each.
30 cm. apart from each other. C 74 galvanize frame with SCG needle point screw
23 mm. with 20 cm. apart from each other and 1.2 cm. Remark : In case need to trowel connection point, you can do as the process for concealed ceiling.
from the edge.

Suggestion
Suggestion
SCG SmartBOARD can be bend-installed by attach the board to the frame as the fixed radiance as follows:
SCG SmartBOARD can be bend-installed by attach the board to the frame as the fixed radiance as follows:

Spacing between Space between Thickness Spacing between Spacing between

Product Thickness (mm.) Minimum Radius Product Minimum Radius
frame fixing tool (mm.) minor studs fixing tool

8 2.00 m. 30 cm. 20 cm. 3.5 - 4 cm. 1.00 m.

SCG SmartBOARD Wall SCG SmartBOARD Ceiling 40 cm. 20 cm.
10 4.00 m. 30 cm. 20 cm.
6 mm. 1.50 m.
Note : Above radius is radius of SCG SmartBOARD in length.
Note : Above radius is radius of SCG SmartBOARD in length.

15 8
2 Wall Installation

2.1 Space Lining External Wall Installation 2.3 Concealed Wall Installation
Frame and accessories Frame and accessories
Frame : Steel C 75 x 45 x 15 x 2.3 mm. Frame : SCG SmartBOARD C 74, U 76 galvanize frame.
Fixing Tool : SCG self drilling wing screw 32 mm. Fixing Tool : SCG self drilling screw 23 mm., SCG needle point screw 10 mm.
SCG self drilling screw 45 mm. (For SCG SmartBOARD 16 mm. thick) Sealant Material : SCG SmartBOARD plaster joint compound, Sandpaper no. 3
Sealant Material : SCG SmartBOARD polyurethane joint sealant. SCG SmartBOARD : 2-side Tapered Edge 8 mm. thick, size 120 x 280 cm.
Corner covered Tool : SCG cement corner.
SCG SmartBOARD : Squared Edge 8 -16 mm. thick. Installation Instruction
Installation Instruction The set-up step is the same as The Space Lining Internal wall Installation.

1 2
60
cm
1 2
. Maximum distance
SCG SmartBOARD 5 cm. of frame 60 cm.
U 76 galvanize frame

SCG SmartBOARD
SCG needle point
C 74 galvanize frame screw 23 mm.

60 cm. 20 cm.
1.2 cm.

SCG SmartBOARD Tapered Edge

Fix studs to structural element no more than 60 cm. Attach SCG Reflective Insulation or moisture impermeable
apart. membrane.
Set up SCG SmartBOARD U 76 galvanize frame on Attach SCG SmartBOARD tapered edge with SCG
the floor and the ceiling with 60 cm. concrete hook and needle point screw 23 mm. as 20 cm. apart from each
after that set up SCG SmartBOARD C 74 galvanize other (as the picture).
3 4 45 mm. frame as 60 cm. apart from each other.

SCG Reflective Insulation 15 mm.

SCG SmartBOARD
20 cm.

.
m
Concealed Instruction
m
SCG self drilling
75
wing screws 32 mm.

Step of concealed wall installation is the same as The Concealed Ceiling Installation

light weight wall frame

covering with Acrylic
1.2 cm. for external painting
Leave the space between
board 0.8 1.6 cm.

Fixing SCG SmartBOARD 8 -12 mm. thick by SCG Leave the space between board 0.8 1.6 cm. SCG needle point screw 23 mm. SCG SmartBOARD Tapered Edge
self drilling wing screw 32 mm., 20 cm. apart from each
other and 1.2 cm. apart from edge of board. Fixing SCG
SmartBOARD16 mm. thick by SCG self drilling screw 45 mm. 1 Apply the primer color to cover the old surface
Tape 3.5 cm. width

5 6 2 Plaster the first layer with 15 cm. width

3 Plaster the second layer with 20 cm. width

tape
4 Plaster the third layer with 28 cm. width

5 Scrub with sandpaper no. 3

6 Apply the primer color cover all over the board

before painting with the real color

Cover the space with tape before applying Fix SCG cement corner by butterfly-wing plastic hook,
SCG SmartBOARD polyurethane joint sealant, take 37 mm. and SCG needle point screw 38 mm. to external
tape off, leave it dry. corner. Suggestion
Concealed wall : using advised only interior and dry area only.

9 14
 2.2 Space Lining Internal Wall Installation 7 finishing the screw head
8
by SCG SmartBOARD

The pole
polyurethane joint sealant.

The pole
Installation Instruction in door or window area

1 2
SCG SmartBOARD
C 74 galvanize frame SCG self drilling wing screw 32 mm.,
boxing C 74 SCG self drilling screw 45 mm.
SCG needle point
60 cm. 60 cm. 60 cm. 60 cm.
Screw 23 mm. SCG SmartBOARD
SCG SmartBOARD
polyurethane joint sealant
SCG SmartBOARD U 76 galvanize frame
SCG self drilling
screw 38 mm.
SCG SmartBOARD C 74 galvanize frame SCG SmartBOARD
Door Frame For internal corner,leave the space between board and Paint old cement primer before covering with Acrylic for
SCG SmartBOARD U 76 galvanize frame
Door Frame apply SCG SmartBOARD polyurethane joint sealant to external painting two layers at least.
Double SCG SmartBOARD the space, leave it dry.
U 76 galvanize frame
SCG SmartBOARD polyurethane
SCG SmartBOARD U 76 galvanize frame joint sealant
Remark : For SCG SmartBOARD 16 mm. thick fixing by SCG self drilling screw 45 mm.

Install the door or window frame to the ceiling frame Seal the joint between panel and frame with SCG
SCG needle point screw 23 mm. with 15 cm. spacing. SmartBOARD polyurethane joint sealant.
Detail for Installation

Metal studs
SCG Reflective Insulation

SCG SmartBOARD
SCG self drilling wing screw 32 mm./45 mm.
Installation Instruction in wall corner
Lift up from the ground 8 mm. zinc No. 28
(for external used)
1 SCG SmartBOARD C 74 galvanize frame
The outside wall installation should lift up the end of
The pole SCG SmartBOARD above soil level at least 10 cm.
10 cm.

soil level
Reinforce concrete beam

SCG needle point screw 23 mm.

SCG SmartBOARD Wall

SCG SmartBOARD polyurethane
joint sealant

Make the gap for 0.5 - 1.0 cm. at wall corner, and
seal the joint between panel and frame with SCG
SmartBOARD polyurethane joint sealant.
Suggestion
For external wall installation, should consider about wind and other forces.

Spacing Frame for SCG SmartBOARD (cm.)

Height of Building (m.) The thickness of SCG SmartBOARD
8 mm. 10 mm. 12 mm.
Less than 10 40 60 70
10 - 20 Not Recommend 40 50
20 - 30 Not Recommend Not Recommend 40
More than 30 Not Recommend Not Recommend Not Recommend

Remark : Length between and the thickness of SCG SmartBOARD, follow the engineer who design the building.

13 10
 2.2 Space Lining Internal Wall Installation 7 8 5 cm.

Frame and accessories SCG SmartBOARD C 74

galvanize frame 5 cm.
Frame : SCG SmartBOARD C 74, U 76 galvanize frame.
Fixing Tool : SCG self drilling screw 23 mm. tube of electrical and plumbing system
Sealant Material : SCG SmartBOARD polyurethane joint sealant. 1.2 cm.
SCG SmartBOARD : Squared Edge 8 mm. thick, 2 size 120 x 240 cm., 120 x 280 cm.
20 cm.
4-inch Square Lining 8 mm. thick, size 120 x 280 cm.
6-inch Square Lining Wood Grain (Golden Teak Color) 6, 8 mm. thick, size 60 x 300 cm.

Installation Instruction

1 2 Install the tube for electric and plumbing system Fix SCG SmartBOARD to the frame by using SCG needle
including the signal cable prior the installation of SCG point screw 23 mm. with 20 cm. spacing, and at 1.2 cm.
SmartBOARD. edge distance, with 5 cm. distance from the panel's corner.

9 10
SCG SmartBOARD Wall

SCG needle point

1 screw 23 mm.

Determine the alignment of wall on the floor and ceiling Install SCG SmartBOARD U 76 galvanize frame on the
board. floor and ceiling board on the required alignment by using
SCG plastic insert 37 mm. and SCG needle point screw
38 mm., in 60 cm. spacing.
1.2 cm. 0.8 cm.
3 4
Leave space of gap for 0.8 cm. (equal to board's Cover the screw head by SCG SmartBOARD plaster
thickness). joint compound for the joint properly.
SCG SmartBOARD U 76
galvanize frame

SCG SmartBOARD C 74
galvanize frame
60 cm.

11 12
tape

Install SCG SmartBOARD C 74 galvanize frame into Fix SCG SmartBOARD C 74 galvanize frame to SCG
SCG SmartBOARD U 76 galvanize frame by insert and SmartBOARD U 76 galvanize frame by SCG self drilling
twist to be perpendicular to SCG SmartBOARD U 76 point screw 10 mm.
galvanize frame, in 60 cm. spacing. *
5 6
Add SCG SmartBOARD
2 pieces of general C 74 frame U 76 galvanize frame

Use the tape to cover the joint prior sealing the joint by Coat the prime coat for original cement for 1 layer, and
SCG SmartBOARD polyurethane joint sealant, then peel cover again by Acrylic Paint for at least 2 layers.
the tape off, and left it dry.

Frame Higher than 280 cm. 280 cm.

* Remark : In case that SCG SmartBOARD with 6-inch square lining wood grain (Golden Teak Color) is used as real wall, the frame should
be installed in every joint along the length of panel in order to allow sealing of the joint by SCG SmartBOARD polyurethane joint sealant.

In case that general light-weight frame is used, another In case that the wall height is higher than 240 or 280 cm.
pair frames shall be used to support the joint between SCG SmartBOARD U 76 galvanize frame shall be used
SCG SmartBOARD. to support on upper horizontal line at the panel level (240
- 280 cm.) as for supporting the panel jointing.

11 12
 2.2 Space Lining Internal Wall Installation 7 8 5 cm.

Frame and accessories SCG SmartBOARD C 74

galvanize frame 5 cm.
Frame : SCG SmartBOARD C 74, U 76 galvanize frame.
Fixing Tool : SCG self drilling screw 23 mm. tube of electrical and plumbing system
Sealant Material : SCG SmartBOARD polyurethane joint sealant. 1.2 cm.
SCG SmartBOARD : Squared Edge 8 mm. thick, 2 size 120 x 240 cm., 120 x 280 cm.
20 cm.
4-inch Square Lining 8 mm. thick, size 120 x 280 cm.
6-inch Square Lining Wood Grain (Golden Teak Color) 6, 8 mm. thick, size 60 x 300 cm.

Installation Instruction

1 2 Install the tube for electric and plumbing system Fix SCG SmartBOARD to the frame by using SCG needle
including the signal cable prior the installation of SCG point screw 23 mm. with 20 cm. spacing, and at 1.2 cm.
SmartBOARD. edge distance, with 5 cm. distance from the panel's corner.

9 10
SCG SmartBOARD Wall

SCG needle point

1 screw 23 mm.

Determine the alignment of wall on the floor and ceiling Install SCG SmartBOARD U 76 galvanize frame on the
board. floor and ceiling board on the required alignment by using
SCG plastic insert 37 mm. and SCG needle point screw
38 mm., in 60 cm. spacing.
1.2 cm. 0.8 cm.
3 4
Leave space of gap for 0.8 cm. (equal to board's Cover the screw head by SCG SmartBOARD plaster
thickness). joint compound for the joint properly.
SCG SmartBOARD U 76
galvanize frame

SCG SmartBOARD C 74
galvanize frame
60 cm.

11 12
tape

Install SCG SmartBOARD C 74 galvanize frame into Fix SCG SmartBOARD C 74 galvanize frame to SCG
SCG SmartBOARD U 76 galvanize frame by insert and SmartBOARD U 76 galvanize frame by SCG self drilling
twist to be perpendicular to SCG SmartBOARD U 76 point screw 10 mm.
galvanize frame, in 60 cm. spacing. *
5 6
Add SCG SmartBOARD
2 pieces of general C 74 frame U 76 galvanize frame

Use the tape to cover the joint prior sealing the joint by Coat the prime coat for original cement for 1 layer, and
SCG SmartBOARD polyurethane joint sealant, then peel cover again by Acrylic Paint for at least 2 layers.
the tape off, and left it dry.

Frame Higher than 280 cm. 280 cm.

* Remark : In case that SCG SmartBOARD with 6-inch square lining wood grain (Golden Teak Color) is used as real wall, the frame should
be installed in every joint along the length of panel in order to allow sealing of the joint by SCG SmartBOARD polyurethane joint sealant.

In case that general light-weight frame is used, another In case that the wall height is higher than 240 or 280 cm.
pair frames shall be used to support the joint between SCG SmartBOARD U 76 galvanize frame shall be used
SCG SmartBOARD. to support on upper horizontal line at the panel level (240
- 280 cm.) as for supporting the panel jointing.

11 12
 2.2 Space Lining Internal Wall Installation 7 finishing the screw head
8
by SCG SmartBOARD

The pole
polyurethane joint sealant.

The pole
Installation Instruction in door or window area

1 2
SCG SmartBOARD
C 74 galvanize frame SCG self drilling wing screw 32 mm.,
boxing C 74 SCG self drilling screw 45 mm.
SCG needle point
60 cm. 60 cm. 60 cm. 60 cm.
Screw 23 mm. SCG SmartBOARD
SCG SmartBOARD
polyurethane joint sealant
SCG SmartBOARD U 76 galvanize frame
SCG self drilling
screw 38 mm.
SCG SmartBOARD C 74 galvanize frame SCG SmartBOARD
Door Frame For internal corner,leave the space between board and Paint old cement primer before covering with Acrylic for
SCG SmartBOARD U 76 galvanize frame
Door Frame apply SCG SmartBOARD polyurethane joint sealant to external painting two layers at least.
Double SCG SmartBOARD the space, leave it dry.
U 76 galvanize frame
SCG SmartBOARD polyurethane
SCG SmartBOARD U 76 galvanize frame joint sealant
Remark : For SCG SmartBOARD 16 mm. thick fixing by SCG self drilling screw 45 mm.

Install the door or window frame to the ceiling frame Seal the joint between panel and frame with SCG
SCG needle point screw 23 mm. with 15 cm. spacing. SmartBOARD polyurethane joint sealant.
Detail for Installation

Metal studs
SCG Reflective Insulation

SCG SmartBOARD
SCG self drilling wing screw 32 mm./45 mm.
Installation Instruction in wall corner
Lift up from the ground 8 mm. zinc No. 28
(for external used)
1 SCG SmartBOARD C 74 galvanize frame
The outside wall installation should lift up the end of
The pole SCG SmartBOARD above soil level at least 10 cm.
10 cm.

soil level
Reinforce concrete beam

SCG needle point screw 23 mm.

SCG SmartBOARD Wall

SCG SmartBOARD polyurethane
joint sealant

Make the gap for 0.5 - 1.0 cm. at wall corner, and
seal the joint between panel and frame with SCG
SmartBOARD polyurethane joint sealant.
Suggestion
For external wall installation, should consider about wind and other forces.

Spacing Frame for SCG SmartBOARD (cm.)

Height of Building (m.) The thickness of SCG SmartBOARD
8 mm. 10 mm. 12 mm.
Less than 10 40 60 70
10 - 20 Not Recommend 40 50
20 - 30 Not Recommend Not Recommend 40
More than 30 Not Recommend Not Recommend Not Recommend

Remark : Length between and the thickness of SCG SmartBOARD, follow the engineer who design the building.

13 10
2 Wall Installation

2.1 Space Lining External Wall Installation 2.3 Concealed Wall Installation
Frame and accessories Frame and accessories
Frame : Steel C 75 x 45 x 15 x 2.3 mm. Frame : SCG SmartBOARD C 74, U 76 galvanize frame.
Fixing Tool : SCG self drilling wing screw 32 mm. Fixing Tool : SCG self drilling screw 23 mm., SCG needle point screw 10 mm.
SCG self drilling screw 45 mm. (For SCG SmartBOARD 16 mm. thick) Sealant Material : SCG SmartBOARD plaster joint compound, Sandpaper no. 3
Sealant Material : SCG SmartBOARD polyurethane joint sealant. SCG SmartBOARD : 2-side Tapered Edge 8 mm. thick, size 120 x 280 cm.
Corner covered Tool : SCG cement corner.
SCG SmartBOARD : Squared Edge 8 -16 mm. thick. Installation Instruction
Installation Instruction The set-up step is the same as The Space Lining Internal wall Installation.

1 2
60
cm
1 2
. Maximum distance
SCG SmartBOARD 5 cm. of frame 60 cm.
U 76 galvanize frame

SCG SmartBOARD
SCG needle point
C 74 galvanize frame screw 23 mm.

60 cm. 20 cm.
1.2 cm.

SCG SmartBOARD Tapered Edge

Fix studs to structural element no more than 60 cm. Attach SCG Reflective Insulation or moisture impermeable
apart. membrane.
Set up SCG SmartBOARD U 76 galvanize frame on Attach SCG SmartBOARD tapered edge with SCG
the floor and the ceiling with 60 cm. concrete hook and needle point screw 23 mm. as 20 cm. apart from each
after that set up SCG SmartBOARD C 74 galvanize other (as the picture).
3 4 45 mm. frame as 60 cm. apart from each other.

SCG Reflective Insulation 15 mm.

SCG SmartBOARD
20 cm.

.
m
Concealed Instruction
m
SCG self drilling
75
wing screws 32 mm.

Step of concealed wall installation is the same as The Concealed Ceiling Installation

light weight wall frame

covering with Acrylic
1.2 cm. for external painting
Leave the space between
board 0.8 1.6 cm.

Fixing SCG SmartBOARD 8 -12 mm. thick by SCG Leave the space between board 0.8 1.6 cm. SCG needle point screw 23 mm. SCG SmartBOARD Tapered Edge
self drilling wing screw 32 mm., 20 cm. apart from each
other and 1.2 cm. apart from edge of board. Fixing SCG
SmartBOARD16 mm. thick by SCG self drilling screw 45 mm. 1 Apply the primer color to cover the old surface
Tape 3.5 cm. width

5 6 2 Plaster the first layer with 15 cm. width

3 Plaster the second layer with 20 cm. width

tape
4 Plaster the third layer with 28 cm. width

5 Scrub with sandpaper no. 3

6 Apply the primer color cover all over the board

before painting with the real color

Cover the space with tape before applying Fix SCG cement corner by butterfly-wing plastic hook,
SCG SmartBOARD polyurethane joint sealant, take 37 mm. and SCG needle point screw 38 mm. to external
tape off, leave it dry. corner. Suggestion
Concealed wall : using advised only interior and dry area only.

9 14
 2.4 Bended Wall Installation 1.5 Curved Surface Installation
Frame and accessories Frame and accessories
Frame : SCG SmartBOARD C 74, U 76 galvanize frame. Frame : Galvanized iron metal ceiling frame (C-line) No.24
Fixing Tool : SCG self drilling screw 23 mm. Fixing Tools : SCG needle point screw 23 mm.
SCG SmartBOARD : Squared Edge 8 mm. thick. SCG SmartBOARD : Squared or Tapered Edge 4 mm. or 6 mm. thick.

Installation Instruction
Installation Instruction (Method of ceiling frame installation follow to frame producer.)
SCG SmatBOARD is flexible, so it can be bended without water soaking as follows :
1 2 attach the studs to
1 2 structural element

fix curved stud

that be bended curved studs
attach the studs to
structural element 100 cm.

Bend studs to have curve form of desired radius. Attach curved stud to structural element no more than
100 cm. apart from each.
Positioning the bended wall installation on both Set up SCG SmartBOARD U 76 galvanize frame on the
ceiling and floor floor and the ceiling with 5 - 10 cm. apart from each other
with the concrete hook at every 30 cm.

3 4
drive screw into major studs
3 4
attach SmartBOARD
hook for connection no more than 40 cm. to prepared studs

75 mm.
45 mm. no more than 40 cm.

no more than 20 cm.

cut flank, curved C-line No.24 apart from each other.
20 cm.
fix minor studs to major studs no more than 40 cm. Attach SCG SmartBOARD to minor studs by SCG
apart. needle point screw 23 mm. length, 20 cm. apart from
Set up SCG SmartBOARD C 74 galvanize frame as Attach SCG SmartBOARD to SCG SmartBOARD each.
30 cm. apart from each other. C 74 galvanize frame with SCG needle point screw
23 mm. with 20 cm. apart from each other and 1.2 cm. Remark : In case need to trowel connection point, you can do as the process for concealed ceiling.
from the edge.

Suggestion
Suggestion
SCG SmartBOARD can be bend-installed by attach the board to the frame as the fixed radiance as follows:
SCG SmartBOARD can be bend-installed by attach the board to the frame as the fixed radiance as follows:

Spacing between Space between Thickness Spacing between Spacing between

Product Thickness (mm.) Minimum Radius Product Minimum Radius
frame fixing tool (mm.) minor studs fixing tool

8 2.00 m. 30 cm. 20 cm. 3.5 - 4 cm. 1.00 m.

SCG SmartBOARD Wall SCG SmartBOARD Ceiling 40 cm. 20 cm.
10 4.00 m. 30 cm. 20 cm.
6 mm. 1.50 m.
Note : Above radius is radius of SCG SmartBOARD in length.
Note : Above radius is radius of SCG SmartBOARD in length.

15 8
 3 Floor Installation
Frame and accessories
1.4 T-Bar Ceiling Installation
Frame : Steel.
Frame and accessories Fixing Tool : SCG self drilling screw 45 mm.
Frame : Galvanized iron metal frame T- Bar 38 mm. in height. Sealant Material : SCG grumcrete.
Fixing Tool : SCG butterfly-wing plastic hook 37 mm. , SCG needle point screw 38 mm. SCG SmartBOARD : Squared Edge 16 - 18 mm. thick.
SCG SmartBOARD : Squared Edge 3.5, 4 and 6 mm. thick, cut into 60 x 120 cm. or 60 x 60 cm.
Installation Instruction

Installation Instruction (Method of ceiling frame installation follow to frame producer.) 1. Prepare the structure to support SCG SmartBOARD flooring by allow the size and spacing of the frame to support the load safely as
designed by the Engineer, or can choose the size and spacing of the frame approximately from the table.

1 2
121 cm. Table 1 Spacing of stinger for the maximum safe load

60.5 cm. SCG SmartBOARD for flooring

major metal studs 121 cm. Distance of support Live Load
Thinkness (mm.) Type of building
minor metal studs (cm.) (kg./m2 )

Wall Angle 16 40 House / Residence 150

60 cm.

40 Hotel / Dormitory 200

Set up the metal studs to the level by lining up major Check the level, make it 121 cm. apart parallel to the
metal studs no more than 121 cm. apart from each major studs row.
other and minor studs 60.5 cm. apart. 40 Office / Bank 250

18 40 School / University 300

3 4
30 Departmentstore / Cinema / Hall / Restaurant / Carpark 400

30 Cargo / Museum / Plant / Publisher 500

Remark : SCG SmartBOARD floor shall not support point load higher than 100 kg., on 10 sq.cm. area.
Do not use in the area which always wet and moist.

2. The frame must provide at least 4.5 cm. width, in case that the steel frame is used there should be a rust protection at appropriate
level and suit to the environment and operating condition.
Cut SCG SmartBOARD into 60 x 120 cm. paint the Attach SCG SmartBOARD to prepared studs.
surface with old cement primer paint, Acrylic paint
2 times for complete cover up of the original color, 3. In case of using SCG SmartBOARD in area that longer than 6 m., all jointing spaces of SCG SmartBOARD and ceramic tiles (floor
leave it dry. covering materials) must be full-filled by SCG SmartBOARD polyurethane joint sealant.

Instruction :
In case need ceiling size 60 x 60 cm. enhance major studs 60.5 cm. in length with existing studs 121 x 60.5 cm.

7 16
 Floor Installation Concealed Instruction (Only SCG SmartBOARD acrylic joint compound shall be used to plaster the joint between
SCG SmartBOARD tapered edge. All System and Opening works shall be completed prior
the plastering).
1
7 8

120 cm.

40 cm.

Check the level of steel frame and the frame spacing must not higher than that designed. 15 cm.

Clean properly, the gap between board shall be embedded Use 6" trowel to make first plastering for 15 cm. width.
2 spacing from by SCG SmartBOARD acrylic joint compound, and leave
edge 5 cm. it dry.

400 mm. spacing from

max.
edge 1.2 cm.
9 10

spacing from cotton tape

edge 1.2 cm.

Place SCG SmartBOARD 16, 18 mm. thick on steel frame and fixed by SCG self drilling screw 45 mm., with maximum 40 mm. spacing,
and 1.2 cm. distance from the edge.

3 15 cm. 20 cm.

Use 3.5 cm. width cotton tape to cover the joint, and Make second plastering by 8" trowel by plastering for
plaster over this cotton tape again, and leave it dry. 20 cm. and leave it dry.

11 12

Clean the jointing area by using a hard brush.

4 5

28 cm.

Make third plastering by 11" trowel by plastering for Polish the plastering by waterproof abrasive paper
28 cm. and leave it dry for 1 day. no.120, and paste the prime coating for original plaster
for whole ceiling board prior covered by 100% acrylic
paint for at least 2 layers.

Recommendation ;
Mix SCG grumcrete with the recommended ratio. Bring mixed SCG grumcrete to paste on the edge of SCG
SmartBOARD 16, 18 mm. thick. The concealed SCG SmartBOARD ceiling shall be installed in the area which will not directly contact to water, or the area that
tend to be vibrated by structure.

17 6
1.3 Concealed Ceiling Installation 6 7
Frame and accessories
Frame : Galvanized iron metal ceiling frame (C-line) No. 24, minimum width of 38 mm.
Fixing Tool : SCG needle point screw 23 mm.
Face Tool : SCG SmartBOARD acrylic joint compound, Stainless trowel, Square wooden-tray,
Cotton tape, Waterproof abrasive paper.
SCG SmartBOARD : 4-side Tapered Edge 6 mm. thick.

Installation Instruction (Method of ceiling frame installation follow to frame producer.)

1 2
Fix next piece of SCG SmartBOARD together without Shape the SCG grumcrete that excesses properly and
80 cm.
space lining. fixed SCG SmartBOARD by SCG self drilling screw
40 cm. 45 mm. SCG SmartBOARD shall be installed alternately
in order to stagger the joint.

major metal studs

8
minor metal studs

Set up the metal studs to the level by lining up major In case of setting up the ceiling under the roof, use minor SCG grumcrete
metal studs no more than 80 cm. apart from each other studs at the connection point of SCG SmartBOARD, on
and minor studs 40 cm. apart. the short-sided.

SCG SmartBOARD SCG self drilling

3 4 16 / 18 mm. screw 45 mm.

steel
100 cm.

Cover the screw head by SCG grumcrete.

Check the level, make it 100 cm. apart parallel to the Stick SCG SmartBOARD into metal stud with SCG
major metal studs row. needle point screw 23 mm. along with adding minor 9
studs at the point connection on the long-sided.

5 6
away from the edge 1.2 cm

40
cm
.
20 cm.
gap between screw

Install next SCG SmartBOARD by following the above Install the surface cover material such as ceramic
method until complete, and clean all surface to be out tile, laminate, parquet, etc. (as indicated in method).
of dust and oil stain by moist cloth. In case that the surface cover material is not installed,
Fix SCG needle point screw 23 mm. away from the edge Use the corner trowel to check over the screw head clean the floor and coat by the prime coat for original
of board 1.2 cm. and 20 cm. apart from each other area before troweling. The head of the screw should cement prior coating with Epoxy twice (as suggested
separate the joint of each board. sink into SCG SmartBOARD about 1 mm. deep. by maker) in order to prevent the surface from scratching.

5 18
4 Underlay Installation
Tools and accessories 1.2 Space Lining Ceiling Installation with Metal Frame
Fixing Tool : Concrete nail 1 inch for SCG SmartBOARD 8 mm. thick.
Concrete nail 1.5 inches for SCG SmartBOARD 10 - 12 mm. thick, Frame and accessories
Glue. Frame : Hollow steel square section 2 x 3 inches, 1.2 mm. thick.
SCG SmartBOARD : Squared Edge 8 - 12 mm. thick. Fixing Tool : SCG self drilling wing screw 28.5 mm.
Sealant Material : SCG SmartBOARD polyurethane joint sealant.
Installation Instruction SCG SmartBOARD : Squared Edge 3.5 - 6 mm. thick.

1 2
Installation Instruction (Method of ceiling frame installation follow to frame producer.)

1 2

40 cm. 60 cm.
5 cm.

Prepare leveled and polished rough surface concrete Mark nailing guideline every 40 cm. and away from the 60 cm.
by let it has 7 days setting time. edge 5 cm.

Install Hollow steel square section 2 x 3 inches. The Install SCG SmartBOARD. The distance between SCG
3 4 distance between frame is 60 x 60 cm. with straight SmartBOARD is around 0.5 cm.
surface, no twisting.

3 4
1.2 cm. 1.2 cm.
SCG self drilling wing screw 28.5 mm. SCG self drilling wing screw 28.5 mm.

1.2 cm. 1.2 cm.

gap between screw 20 cm. gap between screw 20 cm.

For column cut SCG SmartBOARD to fit around the Apply Latex to entire SCG SmartBOARD. 20 cm. 20 cm.
corner.

Tight SCG SmartBOARD with SCG self drilling wing Use the tape before using SCG SmartBOARD
5 6 screw 28.5 mm., 20 cm. apart. polyurethane joint sealant for the smoother of jointing.
gap between each board 1 cm.

gap between two fixing points

is not over than 40 cm. Laminating material 5 6
1.2 cm.
Underlaying Foam SCG self drilling wing screw 28.5 mm.

gap between
the edge 2 cm. SCG SmartBOARD

Leave 5 cm. gap from

an angle of the board 1.2 cm.
gap between screw 20 cm.

Fix SCG SmartBOARD with 1" concrete nail at marked Install flooring for example Laminate, Parquet.
point and keep 1cm. away between SCG SmartBOARD 20 cm.
overlaped.

Suggestion Use SCG SmartBOARD polyurethane joint sealant Apply the primer and paint with Acrylic paint twice.
between SCG SmartBOARD, pull the tape and leave
For fixing SCG SmartBOARD with 1" concrete nail, be careful not to deepen the nail to reach reinforcing steel level.
it dry for 7 days.
Adjust the surface to be that same level before installation.
High drying shrinkage rate materials are not recommended to apply on SCG SmartBOARD.

19 4
1 Ceiling Installation 5 Fixing and Hanging objects

1.1 Space Lining Ceiling Installation with Wooden Frame 5.1 Fixing and Hanging objects
Frame and accessories
Frame : Hard wood frame size 1.5 x 3 inches. Installation Instruction
Fixing Tool : SCG needle point screw 23 mm. or 1 inch nail.
Sealant Material : SCG SmartBOARD polyurethane joint sealant.
SCG SmartBOARD : Squared Edge 3.5 - 6 mm. thick. 1 2

Installation Instruction

1 2

60 cm.
Mark and Drill your desire point. Sunk butterfly - wing plastic hook into the ceiling or
wall hole.
60 cm.

3 4
Install hard wood frame size 1.5 x 3 inches. The distance Install SCG SmartBOARD. The distance between SCG
between frame is 60 x 60 cm. with straight surface, SmartBOARD is around 0.5 cm.
no twisting.

3 4

Drill the screw into the butterfly-wing plastic hook. When the screw is completely installed the butterfly-wing
plastic hook will be tightly fix with SCG SmartBOARD.

20 cm.

Suggestion : Hanging devices can be fixed to both ceiling and wall by using the following accessories.

Tight SCG SmartBOARD with SCG needle point screw For cornering, cut the SCG SmartBOARD oblique as
23 mm. or 1 inch nail, 20 cm. apart. the frame and tight with needle point screw.
Maximum Weight Stand
Product Application Accessories
(kg.)
butterfly-wing plastic hook PT - 5
5 6 SCG SmartBOARD 3.5 mm. thick Ceiling 5
with drilling screw
1.2 cm.
SCG needle point screw 23 mm.
butterfly-wing plastic hook PT - 5
SCG SmartBOARD 4 mm. thick Ceiling 7
with drilling screw

1.2 cm.
butterfly-wing plastic hook PT - 13
SCG SmartBOARD 6 mm. thick Ceiling 10
gap between screw 20 cm. with drilling screw

20 cm. butterfly-wing plastic hook PT - 13

SCG SmartBOARD 8 mm. thick Wall 80
with drilling screw

Use SCG SmartBOARD polyurethane joint sealant Apply the primer and paint with Acrylic paint twice. Recommendations 1. Use the table above to estimate the weight baring level of different thickness and usage of SCG SmartBOARD
between SCG SmartBOARD, pull the tape and leave 2. When hanging heavy weight objects, it is advised to fix your object in the position that is on the studs, the maximum weight
it dry for 7 days.
stand will also vary depending on the strength of different studs.

3 20
 SmartBOARD Cutting and Drilling

5.2 SCG SmartBOARD Maintenance Tools and Accessories

Frame and Accessories Cutting Tool : Electric fiber cutter (4-inch size) or cutter with 1 inch wide-blade.
Frame : C-line frame. Drilling Tool : Electric drilling machine.
Fixing Tool : SCG needle point screw 23 mm. Grinding Tool : Sandpaper, File, Grinding Machine.
Sealant Material : SCG SmartBOARD plaster joint compound, Sandpaper.

Installation Instruction Installation Instruction

In case of Minor Damage ( Less than 2 cm. crack ) To cut with electric fiber cutter : suitable for SCG SmartBOARD in every size (3.5 - 18 mm.)
1 2 1 2

Apply the cotton tape in the form of a cross and apply the After the first coat of the plaster is set, apply the second Use the electric fiber cutter (4-inch size) cut SCG Trim the edge with sandpaper.
first coat of SCG SmartBOARD plaster joint compound. coat and polish with sandpaper after it dries. SmartBOARD according to the set line.

In case of Moderate Damage ( 2 - 5 cm. crack )

1 2 3 To cut with cutter : suitable for SCG SmartBOARD 3.2 - 4 mm.
1.5 cm. 3 - 5 cm.
1 2
10 cm. 10 cm.

Cut C-line frame 10 cm. longer than the Insert the C-line frame from behind by using Apply the cotton tape in the form of a cross
crack on each side. string before drilling the SCG needle point over the crack then apply two layers of SCG Use the cutter to rip on the set line several times Lever cut SCG SmartBOARD (Don't press, or else
screw 23 mm. SmartBOARD plaster joint compound, polish until the trace is 1 of 3 deep in SCG SmartBOARD the edge will not smooth) and trim the edge with
with sandpaper, and apply coat of color. thickness. sandpaper.

In case of Major Damage ( More than 5 cm. crack )

To drill SCG SmartBOARD
1 2 3
1 2
1.5 cm. 3 - 5 cm.

Use electric saw to cut out the damage Fix the C-line frame with SCG self drilling Fix SCG SmartBOARD with SCG self drilling Drill small hole continuously with electric drilling machine Trim the edge with a file and smooth with sandpaper.
area. screw, 1.5 cm. from the edge of the crack screw. Apply the cotton tape then apply two layers according to the set line. Use the hammer knock the
and fix another screw 3 - 5 cm. to both sides. of SCG SmartBOARD plaster joint compound, unwanted piece to come off.
polish with sandpaper, and apply coat of color.

21 2
 Tools and Equipment 6. Placing Ceramic Tiles on SmartBOARD
Frames and Accessories
Leveled Equipment Drill, Cut, Drive, Hold Equipment
Fixing tool : Tile adhesive cement (flexible type)
SCG SmartBOARD : Squared Edge with 10 - 12 mm. thick.

Installation Instruction
SCG Needle Point Screw SCG Self Drilling Screw
1 40 cm.
2
40 cm.
40 cm. 40 cm.
Tape measure Net Chalk liner

SCG Self Drilling Wing Screw SCG Butterfly-wing plastic hook

For SCG SmartBOARD that is going to be attached the Prepare the surface of SCG SmartBOARD by cleaning
Plummet Level Measurement tile, leave 40 cm. gap between studs in order to prevent and applying primer, then leave it dry.
vibration during ceramic installing.
Drilling Machine Hammer

Metal Frame 3 4

Cutter
Electric Fiber cutter
(for 4 mm. thickness)

Patching Material and Equipment

Mix Tile Adhesive Cement (flexible type) as advised in Use the trowel to spread Tile Adhesive Cement (flexible
Galvanized iron metal Galvanized iron metal the manual. type) on all area of SCG SmartBOARD.
frame for T-Bar ceiling ceiling frame (C-line)

5 6

SCG SmartBOARD SCG SmartBOARD SCG SmartBOARD

polyurethane joint sealant Plaster Joint Compound Acrylic Joint Compound

Structure steel SCG SmartBOARD C74, U76

metal wall frame Galvanize Frame
After soaking tiles in the water, make it nearly dry before Place all tiles on SCG SmartBOARD (Jointing line of
Stainless trowel Stainless trowel
placing on SCG SmartBOARD. ceramic tiles must be aligned on board's jointing line).
(11-inch) (6-inch, 8-inch)
Leave it dry for 7 days for stable setting purpose. Then,
joint the gap between tiles.

Made from Siamfibrecement, Ltd.

Suggestion about placing ceramic tiles on SCG SmartBOARD
*Color of the Products in this brochure may vary slightly due to the printing system. *The information in this brochure may be modified or updated by the company without prior notice. It is our recommendation not to do it on the panel which is over 5 meters long. In such case, technical discussion in details with us is needed.

1 22
 Content

SCG SmartBOARD Equipment for Installation

Tools and Equipment 1
SCG Self Drilling Point Screw 10 mm. SCG Needle Point Screw 23 mm.
Used to fix SCG SmartBOARD C 74 and U 76 Galvanize Specially designed to suit with the work operated with Fiber cement
Frame, or fix SCG SmartBOARD C 74 and C 74 Galvanize
Frame in order to make as door or window frames.
material safely, endure, and nice.
Longer life for rust or corrosion, because the material is made from
SCG SmartBOARD Cutting and Drilling 2
Easily install, can drill and fix firmly with two or three layers high-quality steel wires, can be used either external or internal.
of 0.55 mm. thick of steel ceiling frames. Designed to provide the fin around the screw head which make the
Endure to the rust or corrosion because
the material is made from high-quality
screw head fully embedded in the panel automatically resulting nice
surface of work.
1 Ceilling Installation 3
steel wires, can be used either external
or internal.
Containing size : 500 pieces / box 1.1 Space Lining Ceiling Installation with Wooden Frame 3
Containing size : 500 pieces / box 1.2 Space Lining Ceiling Installation with Metal Frame 4
1.3 Concealed Ceiling Installation 5
SCG Self Drilling Wing Screw 32 mm. SCG SmartBOARD polyurethane joint sealant
1.4 T - Bar Ceiling Installation 7
Specially designed to suit with the work operated with Fiber cement This is the polyurethane material used to seal the joint, easily used,
material safely, endure, and nice. and perfectly adhere to the surface of SCG SmartBOARD or 1.5 Curved Surface Installation 8
Longer life for rust or corrosion, because the material is made from any construction materials such as fiber cement, concrete,
high-quality steel wires, can be used either external or internal. brick, roof tile, ceramic tile, aluminium, timber, glass.
Specially designed to provide special drill end, which will not require Used as a joint sealant which can well prevent the leakage,
advance penetration, easily operated, and can drill rapidly into the steel, can be used in either external or internal of building. 2 Wall Installation 9
its fin can core the panel allowing the screw head to be perfectly and Endure to the climate circumstance, and can be painted
nicely embedded into the panel. The fin over without altering the color shade. 2.1 Space Lining External Wall Installation 9
will automatically break whenever the Containing size : 310 ml. / tube,
steel is eventually penetrated. and 600 ml. / foil tube 2.2 Space Lining Internal Wall Installation 11
Containing size : 500 pieces / box
2.3 Concealed Wall Installation 14
SCG SmartBOARD Acrylic Joint Compound SCG SmartBOARD Plaster Joint Compound 2.4 Bended Wall Installation 15
This is joint-plastering material made by already mixed high-quality This is ready-usable plaster cement for joint plastering especially
acrylic. It is prompt to used for plastering the joint of SCG SmartBOARD, made for SCG SmartBOARD. The cement
or other fiber cement panel inside the building. matrix is viscous resulting into smooth
Viscous acrylic matrix, smoothly plastered, plastering surface, easily mixed, no shrinkage,
3 Floor Installation 16
and the surface can be furnished easily while crack, peeling because the material provide
exposing nice plastering or coated panting. high adhesive and can be easily furnished by
Suit with ceiling work. sandpaper.
Containing size : 5 kg. / box Suit with wall work.
4 Underlay Installation 19
Containing size : 25 kg. / bag

5 Fixing and Hanging objects 20

SCG SmartBOARD C 74, U 76 Galvanize Frame 5.1 Fixing and Hanging Objects 20
Thick steel material providing strength, safety, and manufactured in accordance with 5.2 SCG SmartBOARD Maintenance 21
TIS.863-2532 with full thickness of 0.55 mm.
Economic section with 45, 47 mm. width frame section, which will not require to make
the support for the frame in the joint area between SCG SmartBOARD panel, and will reduce
the time and labor for installation. The material is endured for corrosion or rust, and the surface 6 Placing Ceramic Tiles on SCG SmartBOARD 22
is coated by Hot Dip Galvanized Steel Z22.
Coated by specially thick surface to prevent rust or corrosion.

SCG SmartBOARD Equipment for Installation 23

23
 SCG SmartBOARD fiber cement board
SCG SmartBOARD is a new generation of fiber cement material with Technology made the
board gain strength, durability and elasticity in one time. SCG SmartBOARD, with state-of-the-art composition of Recommendation on lifting and moving
Elephant (SCG) Portland Cement, Silica and Special cellulose fiber through Autoclave process, is specifically designed
Lifting or moving of products shall be carried out with
for various ceiling, wall and flooring applications both internal and external usage.
special attention and avoid continuous work in long period
SCG SmartBOARD Ceiling in order to prevent the injury or fatigue. The operator shall
Special Properties
drop oneself on knee and firmly hold the product every
High impact strength from state-of-the-art composition of Elephant (SCG) Portland time that perform the lifting. Then use his leg power to lift
High impact strength
Squared Cement, Silica and Special cellulose developed by our laboratory.
3.5, 4, 6 by holding at 30 cm. distance from the edge of
Water-Resistance and Long lasting even using in hot, humid, and strong raining weather condition SCG SmartBOARD
NEW Non-decay according to JIS Standard A5420.
4-side T
Premium

Termite Resistance Termite resistance from Portland cement material.

4-side T
6 mm. t Bendable. No water is needed to applied while bending the board. Storing Tips Personal Safety Equipment

Flexibility for Should be stored in-door with dry

various designs R = 4.0 m leveled floor on a pallet or 1.5 x 3 inches
R = 2.0 m
R = 1.5 m
R= 1.0 m
wood laid with a span of 60 cm.
Cover with water and dust proof canvas
4 mm. 6 mm. 8 mm. 10 mm.
Wood G
1 m. bending radius 1.50 m. bending radius 2.0 m. bending radius 4.0 m. bending radius Glove Clothes Safty goggle
4 mm. th

With only 30 kg. per sq.m. total weight of internal partition and faster installation than
Light weight, fast and
NEW conventional system, it provides flexibility of designs and durability of applications
easy to install
3-inch S better than conventional systems.
4 mm. th
With specially low heat conductivity compared to typical light - weight ceiling and Dust protection Mask
Support with 1.5 x 3 inches wood Safty Shoes
Better heat resistance wall material, SCG SmartBOARD is the ideal material for preventing heat from in every 60 cm. or a pallet
external environment, reducing energy consumption and answering green designs.

Ventilate Choosing SCG SmartBOARD to match your application SCG SmartBOARD Product Series
4 mm. th
Series
Installation Recommended SCG SmartBOARD Thickness (mm.) Width x Length (mm.) Weight (kg./pc.) Effective Area (sq.m.)
Application Usage area Series Surface System Thickness
Squared Edge Tapered Edge
Ventilate Space Lining, T-Bar, 603 x 1213 - 3.6 0.73
4 mm. th
Any room that you want to prevent Squared Edge Smooth Surface No Space Lining 3.2, 3.5, 4, 6 mm. 3.2 610 x 1220 (2'x4') - 3.6 0.74
problem from termites and moisture, 1220 x 1220 (4'x4') - 7.2 1.49
NEW
Internal Ceiling 4-side Tapered Edge Smooth Surface Concealed Edge 6 mm.
for example: Bathroom, Kitchen, 600 x 2400 - 7.6 1.44
Space Lining, T-Bar,
Storage room, etc. Wood Grain Wood Grain Texture No Space Lining 4 mm. Lite 1200 x 1200 - 7.6 1.44
Ventilate Squared Edge Smooth Surface
Space Lining,
3.5, 4, 6 mm. 1200 x 2400 - 15.2 2.88
No Space Lining
4 mm. th 3.5 603 x 1210 - 3.9 0.73
Ventilated Smooth Surface 610 x 1220 (2'x4') - 4.0 0.74
Space Lining,
Ventilated
No Space Lining 4 mm. 1220 x 1220 (4'x4') - 7.9 1.49
Areas where regularly expose to Wood Grain Wood Grain Texture Ventilated 1220 x 2400 (4'x8') - 15.8 2.97
SCG SmartBOARD Wall External Ceiling Rain and Sun. hole 600 x 1200 - 4.4 0.72
3-inch Square Lining - Smooth Surface Space Lining, 600 x 2400 - 8.7 1.44
Smooth Surface 1. House/Building Roof Overhang Ceiling No Space Lining 4 mm.
Wood Grain - 3-inch Lining Smooth Surface
2. House/Building Terrace 1200 x 1200 - 8.7 1.44
3. Garage, Open Cabin or Cottage 4 1200 x 2400 - 17.4 2.88
- Wood Grain Texture
Square Wood Grain Space Lining 4 mm. 610 x 610 (2'x2') - 2.3 0.37
8, 10, 1 - 3-inch Lining Smooth Surface
1220 x 1220 (4'x4') - 9.0 1.49
- Smooth Surface
1220 x 2400 (4'x8') - 18.0 2.97
Space Lining,
3-inch Square Lining No Space Lining 4 mm. 4.5 1220 x 2400 (4'x8') - 20.2 2.97
- 3-inch Lining Smooth Surface
2-side T 1200 x 2400 - 26.1 2.88
6
8 mm. t Areas where you want light weight wall Squared Edge Smooth Surface
Space Lining,
8 - 12 mm. 1220 x 2440 (4'x8') - 27.0 2.97
No Space Lining
to replace brick walls without beam 1200 x 2400 - 34.8 2.88
reinforcement needed 2-side Tapered Edge Smooth Surface Concealed Edge 8 mm. 8 1200 x 2800 - 40.2 3.36
Light Weight Wall - Durable and High resitant to Impact Squred Edge
1220 x 2440 (4'x8') - 36.0 2.97
Wood Grain/Square Lining - Easy to customize siding designs to - Smooth Surface
4-inch Square Lining No Space Lining 8 mm.
9
1200 x 2400 - 39.2 2.88
maximize individual needs - 4-inch Lining Smooth Surface
1220 x 2440 (4'x8') - 40.0 2.97
- Fast and Easy to Install
- Safe from termites Squared Edge 6-inch Lining with Golden Teak Wood Grain No Space Lining 8 mm. 10 1200 x 2400 - 43.5 2.88
6-inch 1220 x 2440 (4'x8') - 44.9 2.97
Square L
Wood Gr For decorating new built or renovating Space Lining 12
1200 x 2400 - 52.2 2.88
(Golden T Decorative Wall existing wall
Squared Edge 6-inch Lining with Golden Teak Wood Grain
6 mm.
6 mm. 1220 x 2440 (4'x8') - 53.9 2.97
6*, 8 mm 1200 x 2400 - 69.6 2.88
Space Lining
16 1200 x 3000 - 87.0 3.60
4-inch S
For permanent external wall that needs to Squared Edge Smooth Surface 8 - 16 mm. 1220 x 2440 (4'x8') - 72.0 2.97
be expose to sun, rain and wind regularly 8 - 16 mm..
8 mm. th External Wall 18
1200 x 2400 - 78.3 2.88
to replace brick walls because faster 1220 x 2440 (4'x8') - 81.0 2.97
Space Lining
installation, time saving and cost saving. Squared Edge 6-inch Lining with Golden Teak Wood Grain 8 mm.
5.5 1200 x 2400 4 side 24.0 2.88
8 mm.
6
1200 x 2400 4 side 25.8 2.88
* not recommended for structural materials. Suitable for kitchen or bathroom walls Tapered Edge 1220 x 2440 (4'x8') 2 side 26.7 2.97
Backer Board with ceramic tiles finishing which will be Squared Edge Smooth Surface No Space Lining 8 - 16 mm. 8 1200 x 2800 2 side 40.2 3.36
SCG SmartBOARD Floor resistant to impact, termite and moist. 12 1220 x 2440 (4'x8') 2 side 53.6 2.97
Smooth Surface 600 x 2400 - 7.1 1.44
Timber Texture 4 1200 x 1200 - 7.6 1.44
Underlaying for parquet and laminated Space Lining 1200 x 2400 - 15.2 2.88
NEW Floor Underlay Squared Edge Smooth Surface 8 - 12 mm.
floor to reduce time, labour, and cost. 8 - 12 mm. Wood Grain, 3-Inch Lining, Ventilated,
4 600 x 1200 - 5.0 0.72
Ventilated Wood Grain, Ventilated 3-Inch Lining
16, 6-inch Square Lining Wood Grain (Golden Teak Color)
6 600 x 3000 - 11.2 1.80
For internal and external floor which are 8 600 x 3000 - 15.0 1.80
Floor not always soaked in water.
Squared Edge Smooth Surface No Space Lining 16 - 18 mm.
4-inch Square Lining 8 1200 x 2800 - 40.0 3.36
 Specification for Installation of SCG SmartBOARD Installation Manual for Fiber Cement
Board
Caution SCG SmartBOARD Non Asbestos
Do not use as any building's structure or other purposes. The installation shall follow the Installation Manual and use only the standard equipments made
by producer.

Do not eat avoid the smelling.

Attention to avoid danger

The Products of SCG SmartBOARD are designed, while the operation methods are specified to suit with the working condition in Thailand only.
Any application outside Thailand is considered to be direct responsibility of the designer, construction supervisor, and installer.
For Designer
All properties shown in this document are the average values from the testing of products which are in accordance with the specified standards by sampling
the products during period before the product distribution. Any transportation, application, or any procedures
relating to the products such as exposing the products to the sunshine or submerging in water in long period shall result in altering of product properties.
Specifications for any installation are only the basic recommendation for general application. The Method for Installation and applied structure shall
consider from the standard code of building in such country, and shall be direct responsibility of designer and supervisor.
Application of product which is not specified in the Installation Manual shall be direct responsibility of designer and construction supervisor.
For Installer and User
Specifications for any installation are only the basic recommendation for general application. The Method for Installation and applied structure shall
consider from the standard code of building in such country, and shall be direct responsibility of designer and supervisor.
Application of product which is not specified in the Installation Manual shall be consulted with the architect or designer engineer.

Recommendation for Safety Operation

SCG SmartBOARD has composed by the silica. Cutting, grinding, drilling, or polishing of the product shall result in flying dust. If any person accidentally
eat or inhale in a considerable amount or in long period it shall harm the respiratory system or body of that person.
The cutting, grinding, drilling, or polishing of the product shall carried out in good ventilated area, and avoid to use the machine for cutting, grinding, drilling,
or polishing of the product which resulting in high amount of dust.
Wear the Personal Safty Equipment which is in accordance to the standards, such as dust protection mask, safety goggle, clothes, glove, shoes etc.
Not allow any person who does not wear the Personal Protection Equipment which is in accordance to the standards, or any person who is not
concerning with the work into working area in order to avoid any possible accident or injury.
Lifting or transportation of products shall be carried out with special attention. Do not bend down ones back to lift the product nor twist oneself or change
direction during lifting, and avoid working continuously in long period in order to avoid injury and fatigue.
The person who has to perform lifting must carry out by lowing oneself and hold the products firmly, then apply legs power to lift.
Cleaning of the working area after complete the cutting, grinding, drilling, or polishing of the product shall be carried out by vacuum machine, then the
dust container shall be sealed completely, or cleaned by water. Do not sweep because this can cause spreading of dust.
Separate and collect the debris occurred from installation, reparation, dismantle of products with special attention, and eradicate with appropriate methods
which specified by government service.
Clean oneself body with clean water after complete the cutting, grinding, drilling, or polishing of the product.

First Aid
If the dust or any material debris accidentally entered the eye, do not scrub or crush. Clean with clean water several times, and consult the physician
immediately.

Verify that all methods are following the most update of Installation Manual of Products
Installation Manual of Products is always updated. The designer, construction supervisor, and installer shall verify that all methods being used are following
the most update of Installation Manual of Products. They can confirm by the website : www.siamfibrecement.com

0710