EOLO Mini 24-28 Export

EOLO Mini
24-28 Export
Compact wall-hung
instantaneous boilers
with sealed-room
EOLO Mini
EOLO Mini 24-28 Export

EOLO Mini 24 S Export
24 S Export
Compact wall-hung
for central heating only boilers
with sealed-room
S.C FUTURE LINE INSTAL S.R.L

str. Biharia nr.67-77, sector 1, Bucuresti, ROMANIA
serviceimmergas.ro
Dispecerat Non Stop
Tel. Fix : 021-201.11.14
http://serviceimmergas.ro
Technical Documentation Technical Documentation
EOLO MINI 24-28 Export
Compact wall-hung instantaneous boiler with

sealed-room (type C) fan-assisted.
EOLO Mini 24
EOLO Mini 28
General features.
EOLO Mini is a wall-hung, room-sealed, fan-assisted boiler Combustion air intake inside the sealed chamber and the
for central heating and producing domestic hot water and is expulsion of gases are ensured by a fan. A dierential pressure
distinguished by its compact size. switch controls correct fan operation.
It is available with an output power of 24 kW (20,640 kcal/h)
and 28 kW (24,080 kcal/h).
A microprocessor controlled electronic board adjusts and
controls the appliance (burner ignition, temperature adjustment,
ame modulation and diagnostics) and the operating parameters
can be displayed and set by means of a digital interface with
display panel and push buttons.
With the new electronics the boiler can be connected to the
Remote Digital Control for controlling the boiler remotely
with the utmost ease and also integrates the timer/room
thermostat, boiler diagnostics and delivery temperature ther-
moregulation functions.
The boiler is tted with a safety antifreeze system as a
standard feature that protects it against temperatures as low
as -5 C.
The hydraulic circuit is equipped with a copper water-gas
exchanger, a pump unit in a composite material and a new
electric 3-way valve unit that, according to requirements, allows
the boiler water to circulate in the central heating system or
in a stainless steel plate exchanger for the instant production
of domestic hot water; the primary circuit also features an
automatic by-pass and a 3-bar safety valve.
STEM ed 07/07 1http://serviceimmergas.ro EOLO Mini Export

EOLO Mini 24 S Export
Compact wall-hung room-sealed fan-assisted

boiler for central heating only (type C).
EOLO Mini 24 S
General features.
EOLO Mini S is a wall-hung, room-sealed, fan-assisted boiler Combustion air intake inside the sealed chamber and the ex-
for central heating only with an output power of 24 kW pulsion of fumes are ensured by a fan. A dierential pressure
(20,640 kcal/h) which, using an optional kit comprising a 3- switch controls correct fan operation.
way electric valve and domestic hot water probe and necessary
wiring (that can be connected directly to the integrated board), can
be combined with a separate storage tank for the production
of domestic hot water.
A microprocessor controlled electronic board sees to adjusting
and controlling the appliance (burner ignition, temperature set-
ting, ame modulation and diagnostics) which, by means of a
digital interface complete with display and push buttons, lets
you see and adjust the operating parameters.
With the new electronics the appliance can be connected
to the Remote Digital Control for controlling the boiler
remotely with the utmost ease and also integrates the timer/
room thermostat, boiler diagnostics and delivery temperature
thermoregulation functions.
The boiler is tted with a safety antifreeze system as a
standard feature that protects it against temperatures as low
as -5 C.
The hydraulic circuit is equipped with a copper water-gas
exchanger, a pump unit in a composite material and a delivery
manifold on which an automatic by-pass and safety valve,
calibrated at 3 bar, are housed.

EOLO Mini 24 main dimensions and connections.
Height (mm) Width (mm) Depth (mm)

745 450 250
Connections
DOMESTIC
GAS SYSTEM
WATER
G AC AF R M
3/4 1/2 1/2 3/4 3/4
Legend:
G - Gas supply
AC - Domestic hot water outlet
AF - Cold water inlet
R - System return
M - System delivery
V - Electrical connection
EOLO Mini 28 main dimensions and connections.

745 450 310
Connections
DOMESTIC
GAS SYSTEM
WATER
G AC AF R M
3/4 1/2 1/2 3/4 3/4
Legend:
G - Gas supply
R - System return
M - System delivery

EOLO Mini 24 S main dimensions and connections.

745 450 250
Connections
GAS WATER SYSTEM
G RR R M
3/4 1/2 3/4 3/4
Legend:
G - Gas supply
RR - System lling
R - System return
M - System delivery

EOLO Mini 24 main components.
Legend:
1 - Testing holes (A air) - (F ue) 14 - Combustion chamber
2 - Fan 15 - Automatic air vent
3 - D.h.w. ow switch 16 - Circulator boiler
4 - Gas valve 17 - 3-bar safety valve
5 - Filling valve 18 - D.h.w. exchanger
6 - Boiler pressure gauge 19 - 3-way valve (motorised)
7 - Pressure point, positive signal 20 - Automatic by-pass
8 - Pressure point, negative signal 21 - System draining valve
9 - Flue pressure switch 22 - Draught diverter
10 - Sealed chamber 23 - Primary exchanger
11 - Delivery probe 24 - Ignition and detection electrodes
12 - Overheating safety thermostat 25 - Burner
13 - System expansion vessel

EOLO Mini 28 main components.
Legend:
1 - Testing holes (A air) - (F ue) 14 - Combustion chamber
2 - Fan 15 - Automatic air vent
3 - D.h.w. ow switch 16 - Circulator boiler
5 - Filling valve 18 - D.h.w. exchanger
6 - Boiler pressure gauge 19 - 3-way valve (motorised)
7 - Pressure point, positive signal 20 - Automatic by-pass
8 - Pressure point, negative signal 21 - System draining valve
9 - Flue pressure switch 22 - Draught diverter
10 - Sealed chamber 23 - Primary exchanger
11 - Delivery probe 24 - Ignition and detection electrodes
12 - Overheating safety thermostat 25 - Burner

EOLO Mini 24 S main components.
Legend:
1 - Testing holes (A air) - (F ue) 14 - Automatic air vent
2 - Fan 15 - Circulator boiler
4 - Filling valve 17 - Automatic by-pass
5 - Boiler pressure gauge 18 - System draining valve
6 - Pressure point, positive signal 19 - Draught diverter
7 - Pressure point, negative signal 20 - Primary exchanger
8 - Flue pressure switch 21 - Ignition and detection electrodes
9 - Sealed chamber 22 - Burner
10 - Delivery probe
11 - Overheating safety thermostat
13 - Combustion chamber

Control panel.
Legend:
1 - Reset push button 9 - Visual display of temperatures and error codes
2 - Stand-by /summer/winter push button 10 - Unit of measure
3 - (+) push button to increase d.h.w. temperature 11 - Central heating functioning mode
4 - (-)push button to reduce d.h.w. temperature 12 - Winter
5 - (+) push button to increase system water temperature 13 - Summer
6 - (-)push button to reduce system water temperature 14 - Power supplied
7 - Boiler pressure gauge 15 - Flame presence
8 - D.h.w. functioning mode
Note for the EOLO Mini 24 S version:

Although push buttons (3) and (4), for setting the domestic
hot water temperature, and push button (2), (summer mode,
symbol 13), are present and can be selected, they are not
enabled to work.

EOLO Mini 24 S hydraulic circuit (central heating only).
Legend:
1 - 3-bar safety valve
2 - Filling valve
3 - Gas valve
4 - Burner
5 - Primary exchanger
6 - Draught diverter
7 - Fan
8 - Sealed chamber
9 - Flue pressure switch
10 - Delivery probe
11 - Safety thermostat
12 - System expansion tank
13 - Automatic air vent
14 - Boiler circulator
15 - Automatic by-pass
16 - Delivery manifold
17 - Draining valve
G - Gas supply
RR - System lling
R - System return
M - System delivery
The primary circuit with relevant control and safety devices

is triggered each time there is a request for central heating or
antifreeze.

EOLO Mini hydraulic circuit.
Legend:
1 - D.h.w. ow switch
2 - Flow limiter
3 - Filling valve
4 - Gas valve
5 - Burner
6 - Primary exchanger
7 - Draught diverter
8 - Fan
9 - Sealed chamber
10 - Flue pressure switch
11 - Delivery probe
12 - Overheating safety thermostat
14 - Automatic air vent
15 - Circulator boiler
16 - D.h.w. exchanger
17 - 3-way valve (motorised)
18 - Automatic by-pass
19 - System draining valve
20 - 3-bar safety valve
G - Gas supply
R - System return
M - System delivery
The hot water for central heating and domestic use is produced
by a primary and a secondary (d.h.w.) circuits that work as
required.
Primary circuit (Boiler Circuit).
The primary circuit, with relevant control and safety devices, ated to the instant stainless steel plate exchanger (16).
is operated each time either a central heating or d.h.w. This depends on the position of the motorised 3-way diverter
request is made. valve (17) which, when idle allows the water to ow to the
d.h.w. exchanger (16) while if a central heating request is
Operation (see EOLO Mini). made it deviates the ow to the systems delivery (M) and
The heat contained in the fumes produced by combustion is return (R) pipes.
absorbed by the copper blades of the water-gas primary ex-
changer (6) which, in turn, transfers it to the water circulating
inside thanks to the boiler circulator (15).
The water is transferred directly into the system or can be devi-

Head ow rate graph.

The course of the curve that represents the ow rate/head ratio
available for the system depends on how fast the circulator is
working which, depending on the position, gives the system
a bigger or smaller head. The characteristic curves are shown
in the following graphs.
EOLO Mini 24 - 24 S
Head (m H2O)
Head (kPa)
Flow rate (l/h)
EOLO Mini 28
Head (m H2O)
Head (kPa)
Flow rate (l/h)
A = Head available to the system at third speed (with automatic by-pass)

B = Head available to the system at second speed (with automatic by-pass)

Boiler circulator (1). Primary exchanger (1).

The pump works on the primary circuit return; it is part of the It is a lamellar water-gas exchanger with copper tubes and
pump body unit made in a composite material. ns and at whose outlet (delivery) the central heating NTC
The automatic air vent (2) is housed directly on the body. delivery probe (6) and the overtheating safety thermostat (2)
are located.
The four pipes it is made of are connected in series (1).
It is connected to the circulator delivery and to the primary
circuit delivery by means of push-tted pipes (3) and O rings
(5) and locked with forks (4).
2 The exchangers of the 24 and 28 versions dier in the number
of ns (86 in the 24 - 24 S version and 103 in the 28 version)
and in the dierent layout of the delivery and return pipes
(see drawing).
EOLO Mini 24
1
6
1 2
5
3 4 Delivery
Return
EOLO Mini 28
6
1
2
3 4 Return
Delivery

Motorised 3-way diverter valve for combi mod-

els.
It is an electric motor (1) connected to the 3-way unit (2) and
locked by a fork that allows, according to the request made Exchanger Exchanger
(d.h.w. or central heating), boiler water to ow into the central return delivery
heating system or in the d.h.w. plate exchanger.
This depends on the position of the shutter (4) which closes
passage to the system while simultaneously opening it to the
d.h.w. exchanger (d.h.w. position) or vice versa (central heating
position).
The motor (1) is made to work by the electronic board and,
with each 180 rotation, the shutter (4) moves into both
positions.
The hydraulic part consists of a brass unit (2). 2
Operation in the central heating mode.
The shutters (4) counteracting spring (3) is not compressed
(central heating position), keeping passage to the d.h.w. plate
exchanger closed and passage to the system delivery open.
Both the spring (3) and shutter (4) are located inside the 3- D.h.w.
way brass body (2). exchanger
delivery
Operation in the d.h.w. mode. 1 System
The standard position of the hydraulic unit is always in the
delivery
d.h.w. mode.
The electric motor (1) pushes the rod (5) to which the shutter
(4) is connected which closes passage to the system, simultane-
ously opening it to the d.h.w. plate exchanger, the shutters (4) 3
contrasting spring (3) is compressed (d.h.w. position). 4
Both the spring (3) and shutter (4) are located inside the 3-way 5
valve brass body (2).
EXCHANGER
DELIVERY
D.H.W.
EXCHANGER
DELIVERY
SYSTEM
DELIVERY

Safety devices and checks for combi models.
Automatic system by-pass (3).

This device guarantees the circulation of water in the central
heating circuit even when it would be prevented by the high
resistance of the system. 6 2
It works between the central heating delivery and return,
inserted inside the by-pass tting (4) that connects the pump
unit (2) to the 3-way unit.
System lling unit (7).

This is a valve positioned between the boiler circuit and the
domestic cold water inlet and makes it possible to pressurise
the heating system.
7
This unit is connected to the d.h.w. ow switch (6) by means
of a threaded tting and to the pump unit (2) by means of
an O ring.
1
Automatic air vent (1).
It automatically expels gaseous substances from the boiler
circuit.
It is mounted on the circulator delivery, directly on the pump
unit (2). 2
3-bar safety valve (5).

This valve prevents the safety pressure being exceeded in the 5 3
primary circuit (3 bar).
It tted on the front of the pump unit (2) and xed on the
outside by means of a fork.
When this valve triggers, water exits from the boiler return
4
pipe.
Expansion vessel (8). EOLO Mini 28

It compensates for variations in volume as a result of heating
the water which also limits pressure variations. 8
It has a 6-litre capacity (4.5 useful litres) for the 24 model and
7.5 litres (4.5 useful litres) for the 28 model and a preload
pressure of 1.0 bar.
In the 24 model it is rectangular in shape and located on the
right-hand side of the boiler, by the side of the sealed cham-
ber while, in the 28 model it is circular in shape and located
at the rear of the boiler, behind the sealed chamber; in both
models a copper pipe connects the expansion vessel to the
pump unit (2).
EOLO Mini 24
8

Safety devices and checks for S models (central

heating only).
Automatic system by-pass (3).

This device guarantees the circulation of water in the central
heating circuit even when it would be prevented by the high
resistance of the system. 6 2
It works between the central heating delivery and return,
inserted inside the by-pass tting (4) that connects the pump
unit (2) to the delivery manifold.
System lling unit (7).

This is a valve positioned between the boiler circuit and the
domestic cold water inlet and makes it possible to pressurise 7
the heating system.
The lling up unit is connected to the cold water inlet coupling
(6) by means of a threaded tting and to the pump unit (2)
by means of an O ring.
Automatic air vent (1).

It automatically expels any gaseous substances there might be
1
in the boiler circuit.
It is mounted on the circulator delivery, directly on the pump
unit (2).
2
3-bar safety valve (5).
This valve prevents the safety pressure being exceeded in the
primary circuit (3 bar).
It is tted at the front of the pump unit (2) and xed on the 5 3
outside with a fork.
When this valve triggers water exits from the boiler return
pipe. 4
Expansion vessel (8).

It compensates for variations in volume when the water is
heated and also limits pressure variations.
It has a 6-litre capacity (4.5 useful litres) for the 24 S model
and a preload pressure of 1.0 bar.
It is rectangular in shape and located on the right of the boiler,
by the side of the sealed chamber and connected to the pump EOLO Mini 24 S
unit (2) with a copper pipe.
8
Note: EOLO Mini 24 S is a wall-hung boiler for central heat-
ing only but by using the optional kit consisting of a 3-way
electric valve and domestic hot water probe (together with the
necessary wiring), it can be combined with a separate storage
tank for producing domestic hot water.

Secondary circuit (domestic hot water circuit) for combi versions only.
Operation.
When domestic hot water is drawn cold water ows inside
the d.h.w. ow switch (1) which closes the electrical contact
coupled to it (see the electrical circuit).
As a result, the integrated board starts the d.h.w. priority phase
that ignites the burner and, if theres an ongoing central heating
request, switches the 3-way diverter valve (2) moving it into the
working position (see operation of the hydraulic 3-way valve).
This causes the delivery pipe (M) to close and simultaneously
the passage opens to the d.h.w. exchanger (3).
In this way circulation in the central heating system is pre-
vented while it is allowed in the plate exchanger, inside which
the domestic cold water absorbs the heat from the primary
circuit water (see d.h.w. exchanger).
So in this phase, central heating is o, domestic hot water
having priority.
The water/water heat exchange occurs inside the d.h.w. ex-

changer (3) which is secured to the d.h.w. inlet (1) and outlet
(2) body with screws. Cold water
The top of the body on the left allows cold domestic water to inlet
enter, while at the bottom it allows primary circuit return. D.h.w. outlet
In the same way, the top part of the body on the right allows
the outlet of domestic hot water while at the bottom it allows
primary circuit delivery.
3
Primary
circuit return Primary circuit
delivery
D.h.w. outlet 2

D.h.w. ow switch (2).

Whenever domestic hot water is drawn at a rate of at least 1.5
l/min and a dynamic pressure of 0.3 bar, the ow switch (2)
enables the boiler to work in the d.h.w. mode.
This is done by means of a magnet that, lifting when hit by the
ow of domestic cold water, moves near to an electrical contact
(reed relay) causing it to move thanks to the magnetic eect. 1
When the contact closes, which is located outside the pipe
through which the water ows, it enables the adjustment board
to start the domestic hot water priority phase. 2
It consists of two parts (one in brass and one in plastic) that are
coupled together and locked with a pin.
A G1/4 thread on its body connects it to the lling unit 3
(3).
An 7.1 l/min (2 bar) for model 24 and a 9.2 l/min (2 bar) ow
limiter (1) for model 28 is installed at the ow switch exit.
Cold
water inlet
D.h.w. exchanger.
It is a water-water exchanger made of stainless steel plates one
on top of the other - 12 (for model 24) and 14 (for model 28)
1
Cold
- on whose surface the boiler circuit water and the domestic water
cold water ow in counter current and through which the heat inlet
exchange takes place between the two lots of water.
The hydraulic coupling is done using four O rings (1) so it
can be connected directly to the d.h.w. inlet body and to the 1
d.h.w. outlet body.
Primary
circuit D.h.w.
return outlet
Primary
circuit
delivery

Gas circuit.
The circuit consists of an atmospheric burner and a modu- In Honeywell VK 4105 valve, they are connected in series and
lating gas valve for gas combustion and ow rate regulation powered by electric main tension rectied by a diode bridge
respectively. (U1) located inside the connector (2) (see electric layout).
Modulating coil (1).
Operation. This is a low voltage coil controlled by the integrated board.
When the main coils (3) are energised both the inner valve It controls the gas valve stabiliser and allows the outlet pres-
shutters open allowing gas to ow through to the burner. sure to be varied in a way proportionate to the DC current
The ow rate/outlet pressure is regulated by means of the gas running through it.
valve stabiliser via the modulation coil (1).
By means of the burner (7) nozzles the fuel is injected into
Burner.
the horizontal Venturi tubes (ramps) inside which an optimum
The burner consists of horizontal Venturi pipes (6) inside which
air-gas mixture is obtained that is ignited by the spark of the
the gas is injected by the same number of nozzles (7) mounted
ignition electrode (5).
on the manifold (8).
The number of nozzles, whose diameter varies according to
Modulating gas valve. the type of gas utilised (see technical data) are 12 (24 version)
Then gas valve (Honeywell VK 4105 o SIT 845) is equipped and 14 (28 version).
with two main safety coils (3) and one for modulation (1); Ignition occurs thanks to a p.c.b. that controls both the igni-
they are managed by the printed control board. tion (5) and detection (4) electrodes.
Maximum and minimum outgoing pressure adjustments are
to be performed on the gas valve (see gas pressure adjustment Ignition electrode (5).
section). It is controlled by the integrated board that produces an elec-
Main electric coils (3). trical charge between its end and the burner surface, igniting
The two coils are ON-OFF type, they are powered (230 the air-gas mixture when they come into contact.
Volts) by the printed control board when the burner is to be It is located at the front of the burner, by the centre ramp.
ignited. Detection electrode (4).
In SIT 845 valve, they are electrically connected in parallel It is controlled by the integrated board and detects burner
and powered by the power main tension via a relevant con- ignition.
nector (2). It is located at the front of the burner on the same ramp as
the ignition electrode.
1
SIT 845
2 3
1
VK 4105
2

Gas settings.
Maximum and minimum pressure settings are done by means Gas valve SIT 845.
of the gas valve, observing the values given in the tables rela- Setting maximum pressure (EOLO Mini).
tive to each boiler for the corresponding gas type (see technical Draw some domestic hot water after having set its temperature
data). (using the keys on the panel) on maximum.
A dierential pressure gauge is used for reading the pressure, Turn the brass nut (3) clockwise to increase pressure to the
its positive pressure point connected to the gas valve (4) outlet burner and counter clockwise to reduce it.
and to the positive pressure point on the ange with the holes
located at the top of the sealed chamber (see gure). Setting maximum pressure (EOLO Mini S).
Using the keys on the panel, set central heating temperature on
maximum after having set ignition ramp timer on minimum
(see integrated board programming) or, if there is an external
storage tank, draw some domestic hot water after having set
the temperature on maximum (using the keys on the panel).
Turn the brass nut (3) clockwise to increase pressure to the
burner and counter clockwise to reduce it.
Setting minimum pressure (for all models)
(to be done after setting maximum pressure).
After turning power o to the modulating coil, turn the screw
(2) clockwise to increase pressure to the burner and in the op-
posite direction to reduce it.
SIT 845 valve
Legend:
1 - Coil
2 - Minimum output adjustment screw
3 - Maximum output adjustment nut
4 - Gas valve outlet pressure point
5 - Gas valve inlet pressure point
6 - Protection cap

Gas valve Honeywell VK 4105. Converting the gas type.

Setting maximum pressure (EOLO Mini). There are special kits for adapting to a type of gas dierent
Draw some domestic hot water after having set its temperature from the standard one the boilers are intended for (natural
(using the keys on the panel) on maximum. gas or LPG).
Turn the brass nut (3) clockwise to increase pressure to the Conversion consists in changing the burner nozzles and
burner and counter clockwise to reduce it. modifying the programmable P1 parameter on the p.c.b.
Setting maximum pressure (EOLO Mini S). (see integrated board programming).
Using the keys on the panel, set central heating temperature on Minimum and maximum d.h.w. pressures are then set on the
maximum after having set ignition ramp timer on minimum gas valve in the way described above.
(see integrated board programming) or, if there is an external Minimum and maximum output in the central heating mode
storage tank, draw some domestic hot water after having set are set via parameters (see integrated board operation).
the temperature on maximum (using the keys on the panel). Burner ignition pressure is not to be set because the particular
Turn the brass nut (3) clockwise to increase pressure to the way the board works does not require this type of calibration
burner and counter clockwise to reduce it. (see integrated board operation).
Setting minimum pressure (for all models)

(to be done after setting maximum pressure).
After turning power o to the modulating coil, turn the brass
nut (2) clockwise to increase pressure to the burner and in the
opposite direction to reduce it.
VK 4105 valve
Legend:
1 - Coil
2 - Minimum output adjustment nut
3 - Maximum output adjustment nut
4 - Gas valve outlet pressure point
5 - Gas valve inlet pressure point
6 - Protection cap

Flue circuit.
Operation.
The products of combustion, after hitting the water-gas ex-
changer (1), are conveyed to a hood (2) on top of which the
fumes extractor (3) is tted (fan).
Fan operation guarantees the forced expulsion of the fumes 7 8 10 9
and, at the same time, creates a vacuum in the sealed chamber
6
(5) so the combustion air can be aspirated from outside.
Correct fume extraction is controlled by a dierential ue pres-
sure switch (4); when it triggers it either enables or prevents
burner ignition.
3
Air/fumes testing holes (7-8).
There are two holes at the top on the outside of the sealed 4
chamber which can be accessed from the front; they are used
to sample combustion air (7) and fumes (8). 2
The two holes are closed by the one plastic cap (6).
Flue pressure switch signal pressure points (9-

11
10).
There are two pressure points with screw closing at the top on 1
the outside of the sealed chamber. They measure the signal at
the ends of the ue pressure switch (4).
The negative pressure point (9) is connected to a Y-shaped
pipe (11) which, in turn, is connected to the negative pres-
sure point of the ue pressure switch (4) and to the pressure
point on the fan.
The positive pressure point (10) is connected directly to the
inside of the sealed chamber.

Flue pressure switch (4).

It is located at the top, inside the sealed chamber and, by
means of the relative points, measures the dierence in pressure
between the fan output (negative signal) and the inside of
the sealed chamber itself (positive signal).
The signal measured by the pressure switch varies according
to the length of the aspiration/exhaust terminals and can be
measured by the relative pressure points located at the top of
the sealed chamber (9-10).
When this switch trips it causes a contact (S6) to close that
acts on the integrated board, enabling or preventing burner
ignition.
Flue pressure switch ON OFF
triggering pressures Pa (mm H2O) Pa (mm H2O)
EOLO Mini 24-28 52 (5.3) 42 (4.3)
EOLO Mini 24 S 52 (5.3) 42 (4.3)
Fan (3).
The extractor works downstream from the combustion cham-
ber and is secured vertically to the top of the hood (2) from
where it extracts the fumes, conveying them to the exhaust
pipes to which the boiler is connected. It guarantees the ow
of air inside the sealed chamber at the same time.
It is controlled by the integrated board and basically its opera-
tion coincides with that of the burner.

Intake and exhaust systems.

(see the intake and exhaust terminals instructions).
The EOLO Mini 24-28-24 S boiler is designed to be connected

to the push-tting intake and exhaust pipes.
Sealed chamber, fan-assisted conguration

(type C).
Exhaust.
Connection to the fumes exhaust pipes is through a ange (1)
or a anged curve to x to the tting (4) at the top of the sealed
chamber, placing a shaped seal in between (6).
The ange diers according to whether the system is used split 7 5
or concentric.
In the rst case, the passage for the intake of combustion air 4
(5) is closed while in the second case it is used.
To ensure correct operation of the boiler it is necessary to put 1
a diaphragm (7) on the exhaust tting, between it and the
ange used (1). 6
There are dierent diameter diaphragms, mounted accord-
3
ing to the type of pipe and its length (see boiler instruction
booklet).
2
Intake.
Using the split system, connection to the intake pipes is done
in exactly the same way as for the exhaust pipes, connecting
to one of the two 80 mm holes (2) at the top of the sealed
chamber.
The unused hole is closed with one of the plastic caps (3) sup-
plied with the boiler.
If coaxial pipes are used, the intake of combustion air is done
exploiting the concentric hole, outside the exhaust tting
(5).
Intake and Exhaust Kits.

The kits and their accessories permit use of four concentric
systems and two split systems.
As regards pressure losses relating to each accessory, the various
possible combinations and the use of the diaphragms depend-
ing on the length of the pipes used, follow the instructions
given for the intake and exhaust terminals (see the boiler
instruction booklet).
The coupling of the accessories (bends, extensions and termi-
nals) is the tted type while sealing is guaranteed by silicone
lip seals.

Coupling type horizontal concentric kit 60/100. Coupling type vertical concentric kit 80/125.
The exhaust pipe (60 mm ) is tted inside the aspiration The exhaust pipe (80 mm ) is tted inside the aspiration
pipe (100 mm ). pipe (125 mm ).
Connection to the boiler is done using a 90 bend (2) that can Connection to the boiler is done using a ange (2) that, by
be positioned in any direction and which, by means of the means of the 60/100-80/125 adapter (3) and necessary ex-
necessary extensions, is connected to the specic aspiration tensions, is connected to the specic aspiration and exhaust
and exhaust terminal (3). terminal 80/125 with aluminium tile (6).
The maximum overall permitted length beyond the rst bend The maximum overall permitted length is 12.2 straight verti-
(2) is 3 straight horizontal metres. cal metres.
Coupling type vertical concentric kit 60/100.

2 3
The exhaust pipe (60 mm ) is tted inside the aspiration
pipe (100 mm ).
4 5 Connection to the boiler is done using a ange (2) that, by
1 means of the necessary extensions, is connected to the specic
aspiration and exhaust terminal 60 /100 with aluminium
tile.
The maximum overall permitted length is 4.7 straight verti-
cal metres.
Coupling type horizontal concentric kit 80/125.

The exhaust pipe (80 mm ) is tted inside the aspiration
pipe (125 mm ). 8
Connection to the boiler is done using a 90 60/100 bend
(2) that can be positioned in any direction and which, by 7
5
means of the 60/100-80/125 adapter (3) and necessary ex-
tensions, is connected to the specic aspiration and exhaust
terminal (4).
The maximum overall permitted length beyond the rst bend
(2) is 7.3 straight horizontal metres. 4
6
3
2 3
4 5 6 2
1 1

80/80 coupling type separator kit.

Both pipes are 80 mm in diameter.
Connections to the boiler are done using the two specic
anges that allow discharge (4) from the centre tting and
aspiration (3) from one of the two side holes.
The maximum permitted length (aspiration + exhaust) is 33
straight horizontal metres and 41 straight vertical metres.
To avoid condensate problems, the exhaust pipe is limited to
a maximum of 5 metres.
NOTE: For the EOLO Mini 28 version it is compulsory to
install a diaphragm (10) inside the ange (3) and before the
aspiration pipe.
9 5
5 6
7
8
10
7
4 3
1 2
80/80 insulated coupling type separator kit.

Both pipes are 80 mm in diameter.
Connections to the boiler are done using the two specic
anges that allow discharge (4) from the centre tting and
aspiration (3) from one of the two side holes.
Insulation is by way of the seals (6) which create an air gap
with the external concentric 125 mm pipe.
The maximum permitted length is 33 straight metres (aspira-
tion + exhaust).
To avoid condensate problems, the exhaust pipe is limited to
a maximum of 12 metres.
NOTE: For the EOLO Mini 28 version it is compulsory to
install a diaphragm (12) inside the ange (3) and before the
aspiration pipe.
8 5 6
10 7
8
11 9
B 12
A
3
4
2
1

Electrical circuit.
F2 - Neutral fuse
JP1 - Boiler type selector
M1 - Circulator
M20 - Fan
M30 - 3-way valve (motorised)
S2 - Functioning push button
S3 - Block reset push button
S4 - D.h.w. ow switch
S6 - Flue pressure switch
S20 - Room thermostat (optional)

S21 - D.h.w. temperature increase push
button (if enabled to work)

S22 - D.h.w. temperature reduction push

button (if enabled to work)
S23 - Central heating temperature
increase push button
S24 - Central heating temperature
reduction push button
Legend: T1 - Ignition transformer
B1 - Delivery probe T2 - Boiler board transformer
CRD - Remote digital control (optional) U1 - Rectier located inside the con-
DS1 - Display nector of the gas valve (Honeywell
E1 - Ignition electrode gas valve only)
E2 - Detection electrode X40 - Room thermostat jumper
E4 - Overheating safety thermostat Y1 - Gas valve
F1 - Line fuse Y2 - Gas valve modulator
The electrical circuit of the EOLO Mini 24-28-24 S boiler is Nota: The EOLO Mini 24 S is a wall-hung boiler for central
controlled 100% by a p.c.b. which controls boiler functions. heating only which, using an optional kit comprising a 3-way
Some of the control and safety devices work at mains voltage electric valve and a domestic hot water probe together with
(230 Vac) while others at low voltage. the necessary wiring (that can be connected directly to the inte-
grated board), can be combined with a separate storage tank
to produce domestic hot water.
230 V AC circuit.
Control and safety devices.
Detection electrode It detects burner ignition, being hit by its ame.

(E2) It is connected to the integrated board.
Line fuse (F1) They interrupt power to the circuit when power input is over
3.15 AF 250 V
3.15 A.
fuse
Neutral fuse (F2) They are mounted on the integrated board.

Loads.
Ignition electrode It is controlled by the integrated board that produces an electrical charge between its end
(E1) and the burner surface, igniting the air-gas mixture when they come into contact.
It is powered by the integrated board when theres a d.h.w., central heating or antifreeze
Boiler circulator
request.
(M1)
It permits circulation in the primary circuit.
This board is always powered regardless of the position of the functioning button (S2)
Integrated board
(see integrated board operation).
3-way valve With this valve the ow of primary circuit water can be diverted from the central heating
(M30) system to the d.h.w. plate exchanger and vice versa.
(for combi versions only) It is powered by the integrated board.
It is powered by the integrated board when the burner is to be ignited.

In SIT 845 gas valve, it is powered by the electric main tension.
Gas valve (Y1)
In VK 4105 gas valve, it is powered by electric main tension rectied by a diode bridge
(main coils)
(U1) located inside the connector of the gas valve.
It allows gas ow to the burner.
It guarantees the ow of air inside the sealed chamber and evacuation of fumes produced
Fan
by combustion.
(M20)
It is powered by the integrated board.
Low voltage circuit.
Control and safety devices.
This device is used to remotely control the boiler (SUMMER/WIN-

See Remote
Remote digital control TER selection, setting and indicating temperatures, displaying alarms,
digital control
(CRD) resetting, etc.) and acts as a weekly timer/room thermostat.
operation
(optional) If the CRD is installed the existing X40 jumper has to be re-
(CRD)
moved.
D.h.w. ow switch After some d.h.w. has been drawn this switch acts on the integrated
Interrupted
(S4) board provoking operation in the domestic hot water mode.
contact
(for combi versions only) When idle it enables operation in the central heating mode.
It controls the integrated board and enables burner operation when

Flue pressure switch the fumes are evacuated correctly. Changing
(S6) If it closes with the fan o, the start of the ignition cycle is not contact
enabled.

It resets the boiler subsequent to the triggering of the ignition

failure safety device, the overtemperature safety device, electrome-
Reset push button chanical contacts failure or a parasite ame and is used to start the
Push button
(S3) chimneysweep function.
If pressed together with the functioning button (S2) it lets you
access the boiler parameter settings.
The possible functioning selections are:

= Circuit powered, the antifreeze and antiblock functions
Functioning button are still active, the various post-circulation and post-ventilation
functions are completed. Push button
(S2)
( ) = Boiler operation in SUMMER.
( ) = Boiler operation in WINTER.
It lets the integrated board measure the temperature of the primary

circuit delivery water.
Delivery probe NTC probe
If it breaks the burner stops working both in the central heating
(B1) 10 kohm 25C
or d.h.w. mode.
It is located at the main exchanger outlet.
It enables operation in the central heating mode when room tem-

Room thermostat (S20) perature is below that required. Interrupted
(optional) If this room thermostat is installed the X40 jumper must be re- contact
moved.
Overheating safety ther- The burner switches o when the safety temperature (105C) is Clicson thermo-
mostat exceeded. stat with normally
(E4) It is positioned at the main exchanger outlet. closed contact
Loads.
Gas valve modulator It is powered by the integrated board with a variable continuous current.
(Y2) It permits varying of the gas pressure to the burner.

Electrical circuit.
Central heating phase.
(*) depending on the gas valve used, the main coils are powered of all triggering the ignition electrode (E1) and then both the
at mains voltage (SIT 845) or at mains voltage rectied by a gas valve coils (Y1).
diode bridge (U1) housed in the valve connector (Honeywell Burner ignition is detected by the integrated board by means
VK4105). of the ionisation electrode (E2).
Working with the Room thermostat. Remote digital control operation.

By selecting the (Winter) functioning mode with the (S2) By selecting the Winter functioning mode on the Remote
push button, the boiler is enabled to work in the central heat- Digital Control (CRD) panel the boiler is enabled to work in
ing mode. the central heating mode.
When the room thermostat (S20) closes the integrated board If the conditions detected by the CRD require ignition in the
powers the boiler circulator (M1) by means of the K3 relay central heating mode, the integrated board powers the boiler
and, with the deviation of the K1 relay contact, powers the circulator (M1) via the K3 relay and the burner is ignited as
motor (M) of the 3-way valve (M30) which keeps working described above.
until limit switch 1 opens when the central heating posi-
tion is reached. NOTE: With each switching o when the temperature is
In the meanwhile, if the contact of the ue pressure switch reached, the integrated board stops the burner working in the
(S6) is idle, NC, the adjustment circuit powers the fan (M20) central heating mode for a time equal that set with the board
by means of relay K4. parameters (see integrated board operation).
The integrated board, enabled by the safety thermostat (E4)
and consequent switching of the ue pressure switch over to
NO (S6) and if the temperature measured by the NTC
delivery probe (B1) is below the value set on the boilers
control panel, energises the request relay K2 that causes the 2
contacts to close which allows the ignition cycle to start, rst

Electrical circuit.
D.h.w. phase.
(*) depending on the gas valve used, the main coils are powered NO (S6), closes the contact of the request relay K2 that
at mains voltage (SIT 845) or at mains voltage rectied by a causes the 2 contacts to close allowing the ignition cycle to
diode bridge (U1) housed in the valve connector (Honeywell start, rst of all triggering the ignition electrode (E1) and then
VK4105). both the gas valve coils (Y1).
Burner ignition is detected by the integrated board by means
Operation. of the ionisation electrode (E2).
By selecting the (Summer ) or (Winter), functioning
mode with the (S2) push button, the boiler is enabled to work
in the d.h.w. mode.
When some domestic hot water is drawn it causes the contact
of the d.h.w. ow switch (S4) to close. Subsequently, if the
temperature measured by the NTC delivery probe (B1) is below
the d.h.w. value set on the boilers control panel (or on the CRD
if mounted), the integrated board powers the boiler circulator
(M1) by means of the K3 relay and, with the deviation of the
K1 relay contact, powers the motor (M) of the 3-way valve
(M30) which keeps working until limit switch 3 opens when
the d.h.w. position is reached.
In the meanwhile, if the contact of the ue pressure switch
(S6) is idle, NC, the adjustment circuit powers the fan (M20)
by means of relay K4.
The integrated board, enabled by the safety thermostat (E4)
and consequent switching of the ue pressure switch over to

Modulation board.
Inside the boilers control panel is a p.c.b. that controls the (S6) is idle, NC, the adjustment circuit powers the fan (M20)
appliances electrical devices and sees to the linear modulation by means of relay K4.
of burner power. The integrated board, enabled by the safety thermostat (E4)
The appliances functioning status is shown on a display, indi- and consequent switching of the ue pressure switch over to
cating if any of its safety devices have triggered. NO (S6), and if the temperature measured by the delivery
This board is used on all models, whether they are the probe (B1) is below the value set on the boilers control panel,
conventional or sealed chamber type (NIKE/EOLO Mini energises the request relay K2 that causes the 2 contacts to close
24-28, NIKE/EOLO Mini 24 S). The dierent boiler func- which allows the ignition cycle to start.
tioning modes are recognised automatically by means of the During the rst few seconds after the gas valve (Y1) has been
appliances wiring. powered, the current to the modulating coil (Y2) is limited to
The integrated board is always powered regardless of the operat- the predened soft ignition current.
ing positioned determined by the functioning knob (S2). The burner will then go to the minimum value set by setting
The board executes a periodical self-check to make sure it is the Minimum Central Heating Power* parameter and
working properly. During the central heating functioning then reach the maximum value set (if required) by setting the
mode or with the boiler in Stand-by, this function is activated Maximum Central Heating Power* parameter in a time set
every 18 hours from the last boiler check/powering. During in the Central Heating Ramp Time* parameter.
the d.h.w. functioning mode, this self-check starts within Subsequently the signal is varied directly proportionate to the
10 minutes from the last time water was drawn and lasts 10 dierence between the temperature set on the boiler control
seconds. panel and the temperature measured by the delivery probe
NOTE: the boiler stops working (together with indications) (B1).
during the self-check operation. When the set temperature (+5C) is exceeded, the contact of
relay K2 is opened and the burner switched o. Re-ignition
Operation. time depends on how the Central Heating Ignitions Timer*
parameter is set.
Central heating request. Each time the burner switches o the fan and circulator keep
working for another 30 seconds.
By selecting the (Winter),functioning mode with the (S2)
push button, the boiler is enabled to work in the central heat- * see Integrated board programming.
ing mode.
When the room thermostat (S20) closes the integrated board
powers the boiler circulator (M1) by means of the K3 relay.
In the meanwhile, if the contact of the ue pressure switch

D.h.w. request.
When some domestic hot water is drawn it causes the contact
of the d.h.w. ow switch (S4) to close and enables operation
in the d.h.w. mode.
Burner ignition then occurs as it does for the central heating
phase.
During the rst few seconds after the gas valve (Y1) has been
powered, the current to the modulating coil (Y2) is limited to
the predened soft ignition current.
Once the ame is detected, the signal to the modulating coil
is increased so as to immediately reach maximum power set
on the gas valve (if requested).
Flame modulation then occurs with reference to the dier-
ence between the delivery temperature chosen as the d.h.w.
temperature setting and the temperature measured with the
delivery probe (B1).
When the reference temperature is reached, the burner is
kept working at minimum power and switched o when the
limit temperature of 85C is reached (factory set with xed
set-point).
By way of parameter P3 D.h.w. set-point it is possible to
make the burner switch o (opening of the K2 relay contact)
at the set temperature (correlated set-point).
Antifreeze request.
When the temperature measured by the central heating delivery
probe (B1) drops below 4C, the board enables ignition and
keeps the boiler working with the burner at minimum central
heating power until a boiler temperature of 42C is reached
(radiator antifreeze).
Chimneysweep request.
Pressing the Reset push button (S3) for at least 10 seconds
and releasing it, the board enables boiler ignition and keeps
it working at maximum central heating power set for 15
minutes.
During this time only the limit thermostat function is ob-
served (90C) which is carried out by means of the delivery
probe (B1).
The function is indicated on the boiler display panel by the
ashing of the ( and ), symbols; it cannot work if there
is an ongoing d.h.w. request.
It can be interrupted by cutting power to the circuit, putting
the boiler on (Stand-by), or by either carrying out a d.h.w.
request or after the 15 minutes.

Inputs.
Remote digital control It sends the signals to the board relating to the functioning mode (Stand-by/Summer/Winter),
(CRD) temperature adjustments (d.h.w. and central heating) and central heating requests (times,
(optional) room temperature, etc.).
It indicates an ongoing d.h.w. request.

D.h.w. ow switch
After domestic hot water has been drawn it enables boiler opera- Closed = d.h.w.
(S4)
tion in the d.h.w. mode which is given priority over the system request
(for combi versions only)
heating phase.
It enables burner ignition, powering relay K2 when the fumes are

Flue pressure switch evacuated correctly. Changing
(S6) If the NO contact closes with the fan o, the start of the ignition contact
cycle is not enabled.
This is a signal that indicates the burner ame has been detected.
Flame detection It allows the board to increase current to the modulating coil (Y2) after having limited it
(E2) during the ignition phase.
It keeps the gas valve open (Y1).
It is a resistor that varies in an inversely proportionate way to the

Delivery probe NTC probe
temperature of the primary circuit delivery water.
(B1) 10 kohm 25 C
It is also used as a limit thermostat (90C).
Open = Heating
Room thermostat It is a switch with free contacts that closes a circuit (low voltage)
OFF
(S20) on the integrated board, enabling operation in the central heating
Closed = Heating
(optional) phase when room temperature is below that requested.
ON

Outputs.
230 Vac = coils

energised
Powering the gas valve It is a 230 V ac signal indicating that the gas valves main coils
(Y1) (Y1) are energised.
0 Vac = coils not
energised
Ignition electrode It is a high voltage signal (higher than 16 kV) that determines an electrical discharge at the
(E1) end of the ignition electrode located on the burner.
Remote digital control

This is a (BUS) signal by means of which boiler temperature, operation in the d.h.w. or cen-
(CRD)
tral heating mode and triggered alarm codes can be seen on the remote display panel.
(optional)
Gas valve modulator It is a d.c. signal that controls the modulating coil and the pressure of gas to the burner
(Y2) may be varied according to the output required.
Circulator Relay It is a unipolar relay for controlling the circulator (M1) that is excited when its operation
(K3) is requested.
Request Relay This is a bipolar relay that is excited when the burner has to be ignited.
(K2) Boiler ignition is enabled by means of its contact.
It is a relay by means of which the motor (M) of the electric 3-way valve (M30) is pow-
3-way valve relay
ered.
(K1)
It is excited with a central heating request, it remains idle with a d.h.w. request.
Fan relay
A unipolar relay that controls the fan (M20), excited when fan operation is requested.
(K4)
Adjustments.
Depending on the position of the jumper together with the Boiler type parameter set-
Boiler type selector ting, the functioning mode of the type of boiler used can be chosen:
(JP1) - position 1-2 = bithermal boiler
- position 2-3 = mono-thermal boiler

Safety devices.
The circulator (M1) and 3-way valve (M30) are turned on for 30 seconds after:
Circulator antiblock device
- 24 hours of inactivity with the boiler in the SUMMER ( ) mode.
/ 3-way valve
- 3 hours of inactivity with the boiler in the WINTER ( ) mode.
If there is strong resistance of the safety thermostat or ue pressure switch contact (con-
Electromechanical contacts tact not perfectly closed or worn), the integrated board performs a reset and starts a new
block contact verication cycle; if, after 6 such cycles the problem hasnt been solved, the boiler
(safety thermostat and ue is blocked.
pressure switch) To get the boiler working again, press the Reset button (S3) and then make either a
d.h.w. or central heating request.
Boiler operation is blocked if there is a dispersion in the detection circuit or a malfunction

of the ame control that generates an ionisation current (without the gas valve being open)
Parasite ame block lasting at least 20 seconds.
To get the boiler working again, press the Reset button (S3) and then make either a
If, within 10 seconds from the start of the ignition cycle the detection electrode (E2) fails
to detect the ame on the burner, boiler operation is blocked.
The integrated board makes 2 ignition attempts lasting 10 seconds with an interval of 30
seconds after which it shuts down.
No ignition block To get the boiler working again, press the Reset button (S3) and then make either a
NOTE: The malfunction can be reset up to 5 consecutive times after which the function is
inhibited for at least one hour and you gain one attempt each hour; or you gain 5 attempts
putting the boiler in the (Stand-by) position or cutting power o to the circuit.
If the ue pressure switch contact opens while the fan is working, the boiler is blocked.
Flue pressure switch block
If normal conditions are restored the boiler restarts without having to be reset.
(S6)
If it closes with the fan o, the start of the ignition cycle is not enabled.
If the overtemperature safety thermostat contact opens, boiler operation is blocked.

Safety thermostat block
To get the boiler working again, press the Reset button (S3) and then make either a
(E4)
To prevent the water-gas exchanger from overheating in the case of a blocked pump or
very little water circulating in the primary circuit, when the central heating NTC delivery
Insucient circulation
probe (B1) detects as increase in the temperature that exceeds 5C /second, the burner is
switched o. It restarts when the delivery temperature drops below 42C.

To prevent the water-gas exchanger from overheating, at the end of each central heating, an-
Post-circulation pump
tifreeze or chimneysweep request, the circulator (M1) keeps working for 30 seconds.
Sealed chamber After the burner switches o at the end of any request, the combustion chamber is washed
post-ventilation and the fan is kept working for 30 seconds.
Breakage of the central heating delivery probe (B1) is signalled with the visual display of
NTC probe breakage
error code 05 on the boiler display panel and stops operation in both the central heating
(B1)
and d.h.w. mode.
To avoid the water-gas exchanger from overheating and if boiler temperature measured by
Delivery overtemperature
the NTC delivery probe (B1) exceeds 95C, the fan starts working until the temperature
ventilation
drops below 90C.

Digital user interface.
The appliance is adjusted and controlled (burner ignition, by means of a digital interface featuring a display and push
temperature setting, ame modulation and diagnostics), by a buttons.
p.c.b. that can be used to display and set operating parameters
Operating indicators.
When the appliance is working normally, the illumination of
the display is green which, by way of special symbols, indicates
boiler status and functioning mode.
Operating indicators Symbol
Boiler powered without a ame Display powered

Boiler in the central heating mode Symbol 11 on
Boiler in the d.h.w. mode Symbol 8 on
Burner on Symbol 15 on
Chimneysweep function ongoing Symbols 8 and 11 ash simultaneously

Operating malfunctions indicated.

In the event of a failure or malfunction, the illumination of
the EOLO Mini 24-28-24 S display panel changes colour,
going from green to orange if the problem can be rearmed
electrically or from green to red if the problem can be rearmed
manually. The relative error codes, giving the following table,
ash simultaneously on the boiler display panel.
Flashing code Display panel illu- Remote digital

Operating malfunctions signalled
displayed mination colour display panel
No ignition block 01 Red 01
Safety thermostat overtemperature block 02 Red 02
Electromechanical contacts 04 Red 04

NTC delivery probe malfunction 05 Orange 05
Flue pressure switch failure 11 Orange 11
Parasite ame 20 Red 20
Insucient circulation 27 Orange 27
CRD oine malfunction or not compatible 31 Orange 31
Control and adjustment push buttons. Programming the integrated board.

The EOLO Mini 24-28-24 S boilers are equipped with push The EOLO Mini 24-28-24 S boilers are designed so that some
buttons used to select the functioning mode, to set the water of its operating parameters can be programmed if wanted.
temperature in the central heating and d.h.w. modes and to set By modifying these parameters the boiler can be adapted to meet
the boilers operating parameters. ones specic requirements.
See the following table for the association of the push buttons: Proceed as follows to access the programming phase:
- press push buttons (1) and (2) simultaneously for about 15
List of Push seconds;
Description
Buttons - with push buttons (3) and (4) select the parameter you intend
1 Reset push button changing, indicated in the following table:
2 Stand-by / Summer / Winter push button List of

Description
parameters
(+) push button to increase d.h.w.
3 P1 Selecting the type of gas
temperature
(-) push button to reduce the d.h.w.
4 P2 Selecting special gas G110
temperature
(+) push button to increase central heating D.h.w. set-point, xed or correlated (for
5 P3
system water temperature combined boiler version)
(-) push button to reduce central heating D.h.w. thermostat (for boilers used for cen-
6 P3 tral heating only in the case of combination
system water temperature
with a storage tank)
Note for the EOLO Mini 24 S version: P5 Minimum central heating power
Although push buttons (3) and (4), for setting the domestic
P6 Maximum central heating power
hot water temperature, and push button (2), (summer mode,
symbol 13), are present and can be selected, they are not P7 Central heating ignitions waiting time
enabled to work.
P8 Central heating ramp ignition time
P9 Type of boiler (mono- or bithermal)

- modify the corresponding value with push buttons (5) and Central heating power. The EOLO Mini 24-28-24 S boilers
(6), consulting the following tables; are equipped with electronic modulation that adapts boiler
- conrm the value set by pressing the Reset push button (1) power to the real heat requirements of the home. So the boiler
for about 5 seconds; works normally in a variable range of gas pressures ranging
from the minimum to the maximum central heating power
- press the d.h.w. temperature setting push buttons (3) + and according to the systems thermal load.
(4) simultaneously to cancel the operation.
NOTE: the EOLO Mini 24-28-24 S boilers are manufactured
NOTE: if no push buttons are touched for 30 seconds the and calibrated at the nominal output in the central heating
operation is cancelled automatically. phase. But it takes about 10 minutes to reach nominal heating
output, modiable by selecting parameter (P6).
Selecting the type of gas. Setting this function is used to adjust NOTE: if the Minimum central heating power and Maxi-
the boiler so it can work with LPG or Natural Gas. mum central heating power parameters are selected when
Selecting the type of gas there is a central heating request, boiler ignition is allowed
and powering of the modulator with a current equal to the
Range of settable values Parameter relative value set.
LG (LPG) or nG (Natural Gas) (Standard setting) P1 Minimum central heating power
Gas G110 - China gas. Setting this function is used to adjust Range of settable values Parameter
the boiler so it can work with the rst family gases.
from 0 % = (Imin. standard setting) to 63 % Imax P5
Gas G110 - Gas China (rst family gas)
Range of settable values Parameter

Maximum central heating power
on - oF (Standard setting) P2
Fixed or correlated d.h.w. set-point (for combi versions from I Pot. min. heating set (= Imin.)
P6
to 99 % Imax. (Standard setting)
only). By setting the P3 parameter on the on mode, burner
switching o is correlated to the d.h.w. temperature setting. In
the oF mode the burner switches o at the maximum value. Waiting time. The boiler has an electronic timer that prevents
too frequent burner ignitions in the central heating mode.
Fixed or correlated d.h.w. set-point The boiler has its own standard timer set at 3 minutes.
Range of settable values Parameter Central heating ignitions timer
on correlated - oF xed (Standard setting) P3 Range of settable values Parameter

from 1 to 10
D.h.w. thermostat (for boilers used for central heating only 3 = 3 minutes (Standard setting) P7
in the case of combination with a storage tank). By setting 1 = 30 seconds
parameter P3 on the oF mode, boiler ignition for heating do-
mestic water occurs when the temperature of the water inside Central heating ignition ramp timer. The boiler carries out
the tank drops 3C compared to the temperature set. In the an approximate 10 minute ignition ramp to go from minimum
on mode, boiler ignition for heating domestic water occurs power to nominal central heating power.
when the temperature of the water inside the storage tank
drops 11C compared to the temperature set. Central heating ramp timer
NOTE: whatever mode is selected the boiler always switches Range of settable values Parameter
o at a set point value.
from 1 to 10
Domestic hot water thermostat 10 = 10 minutes (Standard setting) P8
1 = 30 seconds
on - boiler ignition at -11C

P3
oF - boiler ignition at -3C (standard setting)

Boiler type. By selecting this parameter you can choose the

mode for the type of boiler in use: instant single-heating boiler
(0), dual-heating boiler (1) or single-heating boiler with stor-
age tank (2) (in the case of combining EOLO Mini 24 S with a
separate storage tank).
NOTE: depending on the selection made, also move the JP1
jumper on the p.c.b.: position 1-2 for the bithermal boiler or
position 2-3 for the mono-thermal boiler.
Attention: the boiler is factory set so only use this function if
the electronic board is replaced.
Boiler type

from 0 to 2
0 = mono-thermal boiler (instantaneous)
P9
1 = bithermal boiler
2 = mono-thermal boiler (with storage tank)

EOLO Mini 24-28 operating sequence.
Central Heating mode D.h.w. mode

Power on Power on
Boiler functioning knob on Winter Boiler functioning knob on Summer or Winter

Enabling integrated board operation Enabling integrated board operation
The functioning knob (Winter position) enables boiler The functioning knob (Summer or Winter position) enables
operation in the central heating mode boiler operation in the d.h.w. mode

Closing of the Room thermostat/ CRD operation
request
Closing the d.h.w. ow switch
Either the room thermostat or the CRD (if installed)
Drawing domestic hot water
detects the conditions that require operation in the central
heating mode

Powering the circulator and 3-way valve Powering the circulator and 3-way valve
The integrated board powers the boiler circulator and the The integrated board powers the boiler circulator and the
electric 3-way valve, the valve is moved into the central heat- electric 3-way valve, the valve is moved into the d.h.w. posi-
ing position tion

Controlling the ue pressure switch contacts
The integrated boards veries the correct position of the ue pressure switch (normally closed contact NC)

Powering the fan
The integrated board powers the fan

Controlling the ue pressure switch contacts
The integrated board veries deviation of the ue pressure switch contact as a consequence of the fan working
(normally open contact NO)

Powering the ignition electrode
The integrated board powers the ignition electrode

Powering the gas valve coils
With the enable of the overtemperature safety thermostat the integrated board powers the gas valve coils

Burner ignition (automatic soft ignition)
The integrated board sends the soft ignition current to the modulating coil

Flame detection
By means of the detection electrode the integrated board detects burner ignition

Boiler working
The burner works at a power that varies according to the type of request, to the adjustments/settings made and to the tem-
peratures detected by the NTC delivery probe

Technical data.
EOLO Mini 24 technical data.
Nominal heat input kW (kcal/h) 25.8 (22146)

Minimum heat input kW (kcal/h) 10.6 (9122)
Nominal heat output (useful) kW (kcal/h) 24.0 (20640)
Minimum heat output (useful) kW (kcal/h) 9.3 (8000)
Eciency at 100% % 93.2
Eciency at 30% of load % 90.3
Outer casing losses with burner On/O % 0.4 / 0.6
Stack losses with burner On/O % 6.4 / 0.06
G20 G30 G31
Gas nozzle diameter mm 1.30 0.77 0.77
Supply pressure mbar (mm H2O) 20 (204) 29 (296) 37 (377)
Max. central heating circuit pressure bar 3

Maximum heating temperature C 90
C.H. temperature adjustment C 38 - 85
C.H. total expansion vessel volume l 4.5
C.H. expansion vessel preload pressure bar 1.0
Appliance water content l 2,4
Available head with 1000 l/h ow rate kPa (m H2O) 17.6 (1.79)
D.H.W. useful thermal power kW (kcal/h) 24.0 (20640)
D.H.W. temperature adjustment C 30 - 60
D.H.W. ow limiter l/min 7.1
Min. pressure for nominal ow rate bar 1.2
Minimum dynamic pressure d.h.w. circuit bar 0.3
Max. d.h.w. circuit pressure bar 10
Minimum ow rate for d.h.w. l/min 2.0
Flow rate for continuous service (T 30C) l/min 10.7
Specic ow rate (T 30C) l/min 11.4
Boiler weight full kg 36.4
Boiler weight empty kg 34
Electrical connection V/Hz 230/50

Nominal power draw A 0.65
Electric power installed W 115
Circulator power draw W 63
Fan power draw W 36
Electrical insulation degree - IPX5D
G20 G30 G31
Fumes ow rate at max heat output kg/h 55 55 57
Fumes ow rate at min heat output kg/h 57 56 57
CO2 at Q. Nom./Min. % 6.7 / 2.5 7.7 / 3.0 7.4 / 2.9
CO at 0% of O2 at Q. Nom./Min. ppm 84 / 70 95 / 70 54 / 62
NOX at 0% of O2 at Q. Nom./Min. ppm 101 / 59 116 / 59 130 / 61
Exhaust ue temperature at max heat output C 111 112 109
Exhaust ue temperature at min heat output C 86 88 87
NOX class - 3
NOX weighted mg/kWh 113
CO weighted mg/kWh 55
Type of appliance C12 / C32 / C42 / C52 / C62 / C82
Category II2H3+

EOLO Mini 28 technical data.

G20 G30 G31

Appliance water content l 2,6
D.H.W. useful thermal power kW (kcal/h) 28.0 (24080)
D.H.W. temperature adjustment C 30 - 60
D.H.W. ow limiter l/min 9.2
Min. pressure for nominal ow rate bar 1.5
Minimum dynamic pressure d.h.w. circuit bar 0.3
Max. d.h.w. circuit pressure bar 10
Minimum ow rate for d.h.w. l/min 2.0
Flow rate for continuous service (T 30C) l/min 12.8
Specic ow rate (T 30C) l/min 13.4

Fan power draw W 45
G20 G30 G31
CO2 at Q. Nom./Min. % 6.8 / 2.45 7.8 / 2.8 7.5 / 2.8
NOX class - 2
Type of appliance C12 / C32 / C42 / C52 / C62 / C82
Category II2H3+
- The ue temperature values refer to an air inlet temperature

of 15C.
- Data relative to d.h.w. performance refer to a dynamic inlet
pressure of 2 bar and an inlet temperature of 15C; these
values are measured at boiler outlet considering that to nd
these declared values mixing with cold water is necessary.

EOLO Mini 24 S technical data.

G20 G30 G31
Appliance water content l 2
Domestic hot water adjustable temperature
(only in case of combining with hot water storage tank) C 20 - 60
Fan power draw W 36
G20 G30 G31
CO2 at Q. Nom./Min. % 6.7 / 2.5 7.7 / 3.0 7.4 / 2.9
NOX class - 3
Type of appliance C12 /C32 / C42 / C52 / C62 / C82
Category II2H3+

EOLO Mini 24 - 24 S variable heat output.
METHANE (G20) BUTANE (G30) PROPANE (G31)

GAS INJECTOR GAS INJECTOR GAS INJECTOR
HEAT HEAT
FLOWRATE PRESSURE FLOWRATE PRESSURE FLOWRATE PRESSURE
OUTPUT OUTPUT
BURNER BURNER BURNER BURNER BURNER BURNER
(kW) (kcal/h) (m3/h) (mbar) (mm H2O) (kg/h) (mbar) (mm H2O) (kg/h) (mbar) (mm H2O)
24,0 20640 2,73 12,10 123,4 2,03 28,50 290,7 2,00 36,60 373,3
22,6 19410 2,57 10,73 109,4 1,92 25,45 259,6 1,89 32,76 334,1
19,8 17000 2,27 8,30 84,7 1,69 19,97 203,7 1,67 25,84 263,6
19,2 16500 2,21 7,84 80,0 1,65 18,92 193,0 1,62 24,51 250,0
18,6 16000 2,15 7,40 75,4 1,60 17,89 182,5 1,58 23,21 236,7
18,0 15500 2,09 6,96 71,0 1,55 16,90 172,3 1,53 21,94 223,8
17,4 15000 2,02 6,54 66,8 1,51 15,93 162,5 1,48 20,71 211,2
16,9 14500 1,96 6,14 62,6 1,46 14,99 152,8 1,44 19,51 199,0
16,3 14000 1,90 5,75 58,7 1,41 14,07 143,5 1,39 18,34 187,1
15,7 13500 1,83 5,37 54,8 1,37 13,19 134,5 1,35 17,21 175,5
15,1 13000 1,77 5,01 51,1 1,32 12,33 125,7 1,30 16,11 164,3
14,5 12500 1,71 4,67 47,6 1,27 11,50 117,3 1,25 15,04 153,5
14,0 12000 1,64 4,33 44,2 1,22 10,69 109,1 1,21 14,01 142,9
13,4 11500 1,58 4,01 40,9 1,18 9,92 101,2 1,16 13,02 132,8
11,0 9500 1,32 2,89 29,4 0,98 7,11 72,5 0,97 9,37 95,6
9,3 8000 1,12 2,20 22,4 0,84 5,30 54,1 0,82 7,00 71,4
EOLO Mini 28 variable heat output.
METHANE (G20) BUTANE (G30) PROPANE (G31)

GAS INJECTOR GAS INJECTOR GAS INJECTOR
HEAT HEAT
FLOWRATE PRESSURE FLOWRATE PRESSURE FLOWRATE PRESSURE
OUTPUT OUTPUT
BURNER BURNER BURNER BURNER BURNER BURNER
(kW) (kcal/h) (m3/h) (mbar) (mm H2O) (kg/h) (mbar) (mm H2O) (kg/h) (mbar) (mm H2O)
28,0 24080 3,17 11,80 120,4 2,36 27,70 282,5 2,33 35,60 363,1
26,7 23000 3,03 11,10 113,2 2,26 26,07 265,9 2,22 33,60 342,7
26,1 22410 2,95 10,72 109,3 2,20 25,18 256,8 2,17 32,51 331,6
24,4 21000 2,77 9,81 100,1 2,07 23,07 235,4 2,03 29,89 304,9
23,3 20000 2,65 9,17 93,5 1,97 21,59 220,2 1,94 28,03 285,9
22,1 19000 2,52 8,53 87,0 1,88 20,10 205,0 1,85 26,17 266,9
20,9 18000 2,39 7,88 80,4 1,78 18,62 189,9 1,76 24,29 247,8
19,8 17000 2,27 7,24 73,9 1,69 17,13 174,8 1,67 22,41 228,5
18,6 16000 2,15 6,59 67,2 1,60 15,64 159,6 1,57 20,50 209,1
17,4 15000 2,02 5,94 60,6 1,51 14,14 144,3 1,48 18,58 189,5
16,3 14000 1,90 5,28 53,9 1,41 12,64 128,9 1,39 16,63 169,6
15,1 13000 1,77 4,62 47,1 1,32 11,11 113,4 1,30 14,65 149,5
14,0 12000 1,65 3,94 40,2 1,23 9,57 97,7 1,21 12,65 129,5
12,8 11000 1,52 3,26 33,3 1,14 8,02 81,8 1,12 10,60 108,1
11,6 10000 1,40 2,57 26,2 1,04 6,43 65,6 1,03 8,52 86,9
10,5 9030 1,27 1,88 19,2 0,95 4,87 49,7 0,94 6,45 65,8


EOLO Mini 24-28 Export - Manual Tehnic - Ed 07-07 Centrala Termica

Uploaded by

Copyright:

Available Formats

EOLO Mini 24-28 Export - Manual Tehnic - Ed 07-07 Centrala Termica

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

EOLO Mini 24-28 Export - Manual Tehnic - Ed 07-07 Centrala Termica

Uploaded by

Copyright:

Available Formats

EOLO Mini

S.C FUTURE LINE INSTAL S.R.L

EOLO MINI 24-28 Export

Compact wall-hung instantaneous boiler with

STEM ed 07/07 1http://serviceimmergas.ro EOLO Mini Export

EOLO Mini 24 S Export

Compact wall-hung room-sealed fan-assisted

STEM ed 07/07 2http://serviceimmergas.ro EOLO Mini Export

EOLO Mini 24 main dimensions and connections.

Height (mm) Width (mm) Depth (mm)

EOLO Mini 28 main dimensions and connections.

Height (mm) Width (mm) Depth (mm)

STEM ed 07/07 3http://serviceimmergas.ro EOLO Mini Export

EOLO Mini 24 S main dimensions and connections.

Height (mm) Width (mm) Depth (mm)

STEM ed 07/07 4http://serviceimmergas.ro EOLO Mini Export

EOLO Mini 24 main components.

STEM ed 07/07 5http://serviceimmergas.ro EOLO Mini Export

EOLO Mini 28 main components.

STEM ed 07/07 6http://serviceimmergas.ro EOLO Mini Export

EOLO Mini 24 S main components.

STEM ed 07/07 7http://serviceimmergas.ro EOLO Mini Export

Note for the EOLO Mini 24 S version:

STEM ed 07/07 8http://serviceimmergas.ro EOLO Mini Export

EOLO Mini 24 S hydraulic circuit (central heating only).

The primary circuit with relevant control and safety devices

STEM ed 07/07 9http://serviceimmergas.ro EOLO Mini Export

EOLO Mini hydraulic circuit.

Primary circuit (Boiler Circuit).

STEM ed 07/07 10http://serviceimmergas.ro EOLO Mini Export

Head ow rate graph.

Flow rate (l/h)

Flow rate (l/h)

A = Head available to the system at third speed (with automatic by-pass)

STEM ed 07/07 11http://serviceimmergas.ro EOLO Mini Export

Boiler circulator (1). Primary exchanger (1).

STEM ed 07/07 12http://serviceimmergas.ro EOLO Mini Export

Motorised 3-way diverter valve for combi mod-

STEM ed 07/07 13http://serviceimmergas.ro EOLO Mini Export

Safety devices and checks for combi models.

Automatic system by-pass (3).

System lling unit (7).

3-bar safety valve (5).

Expansion vessel (8). EOLO Mini 28

STEM ed 07/07 14http://serviceimmergas.ro EOLO Mini Export

Safety devices and checks for S models (central

Automatic system by-pass (3).

System lling unit (7).

Automatic air vent (1).

Expansion vessel (8).

STEM ed 07/07 15http://serviceimmergas.ro EOLO Mini Export

The water/water heat exchange occurs inside the d.h.w. ex-

STEM ed 07/07 16http://serviceimmergas.ro EOLO Mini Export

D.h.w. ow switch (2).

STEM ed 07/07 17http://serviceimmergas.ro EOLO Mini Export

STEM ed 07/07 18http://serviceimmergas.ro EOLO Mini Export

SIT 845 valve