FP-VRC

FP-VRC
Four Post Vertical Reciprocating Conveyor
PROFESSIONAL PARKING SOLUTION PROVIDER!

WE PLAN , DESIGN, MANUFACTURE AND INSTALL...

QINGDAO MUTRADE CO., LTD.

 FP-VRC
Four Post Vertical Reciprocating Conveyor

Introduction
VRC (Vertical Reciprocating Conveyor) is a
transportation conveyor moving car from one
floor to another, it is a highly customized
product, which could be customized according
to customers different requirements from lifting
height, lifting capacity to platform size!

-FP-VRCis a kind of car or goods lift, and industry

use vertical table lift
-Self-standing and self-support structure
-Hydraulic cylinder + steel chains drive system
-High precision and stable hydraulic drive system
-Automatic shut-off if operator releases the button
switch
-Double chain design for higher safety
-High density chains with longer service lift
-Remote control is optional
-Top quality diamond steel plate
-Hydraulic overloading protection available

General Parts

Double chains Safety Features

2 Hydraulic cylinder
1
1 Double Chain
-High density chains with longer service life

Safety rail
Data Sheet FP-VRC 03 2014 QingDao Mutrade Co,.Ltd.

5
Pallet
3 4
Carriage

Post
2 High precision
-hydraulic drive system
Power pack &
main control panel 3 Limit switch
-To stop the power pack pumping
when the platform reach the floors
Basement 4 Stable
Ramp -145mm thickness platform
5 900mm high safety rail

Qingdao Mutrade Co., Ltd. www.qdmutrade.com Page 1 of 5

Specifications

Model FP-VRC
Lifting capacity 2,000-10,000 kg*can be customized according to your requirement
Lifting height 2,000-13,500mm*can be customized according to your requirement
Platform length 2000mm-6000mm*can be customized according to your requirement
Platform width 2000mm-5000mm*can be customized according to your requirement
Platform material Diamond steel sheet (standard) / 4mm Aluminum steel sheet (optional)
No. of level according to your requirement
Drive mode Hydraulic(cylinder with double steel chains)
Operation button switch (standard) / remote controller (optional)
Power pack 4 kw hydraulic power pump
Lifting speed 4m/min
Safety devices Mechanical anti-falling lock
Finishing Paint spray
Color according to your requirement

Reference Drawing

QINGDAO MUTRADE CO., LTD. 533 755

TPTP-2

110

TPP-2
326 2120

187
6640

6300

FPSP-4
5000

5000
200
900

1900
FPP-2
200.0

446 446 2300

5000
2500

Main tachnicaI parameters

BDP-3

Lifting weight:5000kg
PFPP-3
Lift Stroke:5000mm
Lifting speed:more than 4000mm/min
Pump pressure:18MPa
2500

VRC
Motor power:4kw


4550

4800
CTT

Drawing above is just a sample, for specific project please contact our sales to confirm exact specifications and
drawing.

Qingdao Mutrade Co., Ltd. www.qdmutrade.com Page 2 of 5

 Electric & Hydraulic System
Electric

Code Model Name Specifications Quantity

-KM
FU1 U2 KM CTX2-1201 AC Contactor
L1 24V 1
FU2 V2 M
L2 KA JZ7-44 Intermediate
FU3 W2 ~ 24V 1
L3
PE Relay
AC BK50 Transformer 50VA 380V-24V 1
FU RT18-32X Fuse FU1,FU2,FU3/20A 4
SA SB
FU4/10A
AC 1 2 KA SAO 11Y/Z Electrical Look 1
SB1 SB2 KM1 KA1
SBO 11Y/Z Emergency Stop 1
380V

24V
FU4
Button
KA2 KM1
SB LA-19 Button 2
KM KA VC DC
LH HL2AD11-24V Indicator Light 1
LH
JTE-1081J Alarm Lamp 2
4
KA SQ YBLX-K111
50 Limit switch 1
3
M Y112M-4 Motor 1
OC Solenoid valve 24V 1

Hydraulic System
7
Number Modol Name Quantity Remark
6
1 WU63100 Filter 1

5 2 CBW310 Oil pump 1 Pressure 21MPa

8 3 YF-L10H4 Preasure relief valve 1 31.5MPa
4
4 DFY-L10H2 One -way valve 1
9 5 Pressure mater 1
6 DSG-03-2B2 Electromagnatic 1 24AC
M
-D24-DL directional valve
3
7 Hydraulic cylinder 1
8 KC-03 Flow control valve 1
2
9 Y112M-4 Motor 1 Power 4KW
1

Mechanical System
Chains diagram Lock diagram

Locking latch

Chain Lifting frame

Transmission beam schematic
Cylinder head schematic Chain
Chain
Chain

platfom schematic
Cylinder schematic Locking plate

Column

Locking latch is at the position during maintenance Locking latch is at the position during operation

Locking latch position diagram

Qingdao Mutrade Co., Ltd. www.qdmutrade.com Page 3 of 5

Installation & Maintenance Plan

Installation
(1) Install the automobile lift on a hard concrete foundation which could not vibrate during work.
(2) Install the column bolts in the chassis, and fix the chassis to the ground vertically after installation.
(3) Bolt the transmission beam to the vertical column.
(4) Connect the tray to the lifting beam.
(5) Connect the chains.
(6) Fix the hydraulic station to the back of a vertical column, connect an oil tube, and fill 30# hydraulic oil to the oil tank of
the pump station.
(7) Apply grease to chains and idler pulleys.

Maintenance and Service

(1) Keep clean
Keep this automobile lift clean. Before cleaning, turn power off to assure safety.
(2) Keep the workplace clean. Too much dust will wear the parts and shorten their service life.
(3) Check the chains
Check the chains are in good conditions. In case of chain failure, repair it immediately to prevent an accident.
(4) Maintenance of the hydraulic system
i. Cleaning and oil replacement
After three months use of this automobile lift, clean the hydraulic system and replace 30# hydraulic oil. After that, clean
the hydraulic system and replace 30# hydraulic oil once every six months.

Packaging

Standard packaging:

At MUTRADE, we offer professional steel frame packaging for easy and stable container load. There are 2 types of different
packaging:

1.Packing by single unit(good for retails,

all the parts and structures packaging
separately)

2. Packing by two or more units (good for

big projects, similar parts are packed
together, e.g. all platform parts in 1
package, posts in other packages). It
takes less container space and saves
delivery cost.

Qingdao Mutrade Co., Ltd. www.qdmutrade.com Page 4 of 5

Q&A
1. Is this product can be used indoor or outdoor?
FP-VRC can be installed both indoor and outdoor as long as the site dimensions are enough.
2. What is the surface finishing for this product?
Its paint spray as standard treatment, and optional aluminum steel sheet can be covered above for better water-proof and
looking.
3. What is the power requirements? Is single phase acceptable?
Generally speaking, a 3-phase power supply is a must for our 4Kw motor. If the usage frequency is low (less than one
movement per hour), a single phase power supply can be used, otherwise it may lead to motor burnt out.
4. Can this product still operate if electricity failure happens?
Without electricity the FP-VRC cannot work, so a back-up generator may be needed if electricity failure happens often in
your city.
5. What is the warranty?
Its five years for main structure and one year for moving parts.
6. What is the production time?
Its 30 days after prepayment and final drawing confirmed.
7. What is the shipping size? Is LCL acceptable, or it must be FCL?
As FP-VRC is a fully customized product, the shipping size depends on the specifications you need.
As there are some electrical parts and hydraulic parts, and the packages for components are in different shapes, LCL cannot
be used. 20 feet or 40 feet container is necessary as per the lifting height.

Reference Pictures

Qingdao Mutrade Co., Ltd. Tel : +86 532 5557 9606/608 Add: Room205, BuiLding A, #63 Haier Road, Page 5 of 5
Website:www.qdmutrade.com Fax: +86 532 5557 9607 Laoshan District, Qingdao, China 266100