Scribd
Upload
44 views3 pages

Schottky Barrier Rectifier Diodes PRV: 20 - 40 Volts I: 3.0 Ampere

1. These are Schottky barrier rectifier diodes with peak reverse voltages of 20-40V and a forward current rating of 3A. 2. They feature high current and surge capability, reliability, efficiency, and low power loss and cost. 3. They come in a plastic DO-201AD package with axial leads and are rated for operation from -65°C to +125°C.

Uploaded by

Walther Estevez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
44 views3 pages

Schottky Barrier Rectifier Diodes PRV: 20 - 40 Volts I: 3.0 Ampere

1. These are Schottky barrier rectifier diodes with peak reverse voltages of 20-40V and a forward current rating of 3A. 2. They feature high current and surge capability, reliability, efficiency, and low power loss and cost. 3. They come in a plastic DO-201AD package with axial leads and are rated for operation from -65°C to +125°C.

Uploaded by

Walther Estevez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

1N5820 - 1N5822 SCHOTTKY BARRIER

RECTIFIER DIODES
PRV : 20 - 40 Volts
DO-201AD
IO : 3.0 Ampere
FEATURES :
* High current capability 1.00 (25.4)
0.21 (5.33) MIN.
* High surge current capability 0.19 (4.82)
* High reliability
* High efficiency
0.375 (9.52)
* Low power loss 0.285 (7.24)
* Low cost
* Low forward voltage drop
1.00 (25.4)
0.052 (1.32) MIN.
MECHANICAL DATA : 0.048 (1.22)
* Case : DO-201AD Molded plastic
* Epoxy : UL94V-O rate flame retardant
* Lead : Axial lead solderable per MIL-STD-202,
Method 208 guaranteed Dimensions in inches and ( millimeters )
* Polarity : Color band denotes cathode end
* Mounting position : Any
* Weight : 1.1 grams

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS


Rating at 25 C ambient temperature unless otherw ise specified.
Single phase, half w ave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.

RATING SYMBOL 1N5820 1N5821 1N5822 UNIT


Maximum Recurrent Peak Reverse Voltage VRRM 20 30 40 Volts
Maximum RMS Voltage VRMS 14 21 28 Volts
Maximum DC Blocking Voltage VDC 20 30 40 Volts
Maximum Average Forward Current
0.375", 9.5mm Lead Length at TL = 95 C IF(AV) 3.0 Amps.
Peak Forward Surge Current,
8.3ms single half sine wave Superimposed
on rated load (JEDEC Method) TL = 75C IFSM 80 Amps.
Maximum Forward Voltage at I F = 3.0 Amp. (Note 1) VF 0.475 0.500 0.525 Volt.
Maximum Reverse Current at Ta = 25 C IR 2.0 mA
Rated DC Blocking Voltage (Note 1) Ta = 100 C IR(H) 20 mA
Typical Thermal Resistance (Note 2) RJL 20 C/W
Junction Temperature Range TJ - 65 to + 125 C
Storage Temperature Range TSTG - 65 to + 125 C

Notes :
(1) Pulse Test : Pulse Width = 300 s, Duty Cycle = 2%.
(2) Thermal Resistance from Junction to Lead Vertical PC Board Mounting, 0.5" (12.5mm) Lead Lengths w ith 2.5 in 2
(63.5mm2) copper pads. UPDATE : SEPTEMBER 12, 1998
RATING AND CHARACTERISTIC CURVES ( 1N5820 - 1N5822 )

FIG.1 - FORWARD CURRENT DERATING CURVE FIG.2 - MAXIMUM NON-REPETITIVE PEAK


FORWARD SURGE CURRENT
AVERAGE FORWARD CURRENT,

3.0 100

PEAK FORWARD SURGE


CURRENT, AMPERES
2.4 80
AMPERES

1.8 60

1.2 40

0.6 20

0 0
0 20 40 60 80 100 120 140 1 2 4 6 10 20 40 60 100

LEAD TEMPERATURE, (C) NUMBER OF CYCLES AT 60Hz

FIG.3 - TYPICAL FORWARD CHARACTERISTICS FIG.4 - TYPICAL REVERSE CHARACTERISTICS


REVERSE CURRENT, MILLIAMPERES

20 10
FORWARD CURRENT, AMPERES

1N5820 1N5822
10 TJ = 100 C

1.0

1N5821

1.0 0.1 TJ = 25 C

TJ = 25 C
PULSE WIDTH = 300s 0.01
DUTY CYCLE = 1% 0 20 40 60 80 100 120 140

PERCENT OF RATED REVERSE


0.1
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 VOLTAGE, (%)

FORWARD VOLTAGE, VOLTS


This datasheet has been download from:

www.datasheetcatalog.com

Datasheets for electronics components.

You might also like