Short Circuit Detailed Report WHR PLANT

3P Fault- IEC60909 Method at the Following Times

Bus Name Pre Fault Initial Peak Short 0.5 Cycle 1 Cycle 3 Cycle 5 cycle Std
Voltage Symmetric Circuit Symmetric Symmetric Symmetric Symmetric Symmetric
al Current al SC al SC al SC al SC al SC
SCCurrent Current Current Current Current Current
AQC1 MCC 415 27819 57194 27819 27783 27746 27715 27715
AQC2 MCC 415 19664 34936 19664 19648 19631 19617 19617
COMMON BOP MCC 415 26071 51206 26071 26040 26007 25981 25981
Emergency MCC 415 25539 50932 25539 25509 25478 25452 25452
MLDB 415 24546 47015 24546 24519 24491 24467 24467
MPDB 415 26885 53594 26885 26852 26817 26789 26789
PH1 MCC 415 26764 54232 26764 26731 26697 26669 26669
PH2 MCC 415 25539 50932 25539 25509 25478 25452 25452
Turbine MCC 415 22397 43067 22397 22375 22351 22332 22332
LL Fault - IEC60909 Method at the Following Times
Bus Name Pre Fault Initial Peak Short 0.5 Cycle 1 Cycle 3 Cycle 5 cycle Std
Voltage Symmetric Circuit Symmetric Symmetric Symmetric Symmetric Symmetric
al Current al SC al SC al SC al SC al SC
SCCurrent Current Current Current Current Current
AQC1 MCC 433 24118 49567 24118 24088 24056 24030 24030
AQC2 MCC 433 17040 30269 17040 17027 17012 17000 17000
COMMON BOP MCC 433 22599 44374 22599 22573 22546 22524 22524
Emergency MCC 433 22139 44137 22139 22113 22087 22065 22065
MLDB 433 21276 40740 21276 21253 21230 21210 21210
MPDB 433 23306 46445 23306 23278 23249 23225 23225
PH1 MCC 433 23202 46998 23202 23174 23145 23121 23121
PH2 MCC 433 22139 44137 22139 22113 22087 22065 22065
Turbine MCC 433 19412 37317 19412 19393 19373 19357 19357
LG Fault - IEC60909 Method at the Following Times
Bus Name Pre Fault Initial Peak Short 0.5 Cycle 1 Cycle 3 Cycle 5 cycle Std
Voltage Symmetric Circuit Symmetric Symmetric Symmetric Symmetric Symmetric
al Current al SC al SC al SC al SC al SC
SCCurrent Current Current Current Current Current
AQC1 MCC 433 26141 52948 26141 26121 26100 26082 26082
AQC2 MCC 433 16890 30813 16890 16882 16873 16866 16866
COMMON BOP MCC 433 23962 47007 23962 23945 23927 23912 23912
Emergency MCC 433 22431 44203 22431 22416 22400 22388 22388
MLDB 433 21908 42170 21908 21894 21879 21867 21867
MPDB 433 25128 49866 25128 25109 25090 25074 25074
PH1 MCC 433 24357 48669 24357 24339 24321 24305 24305
PH2 MCC 433 22431 44203 22431 22416 22400 22388 22388
Turbine MCC 433 18099 34660 18099 18089 18079 18071 18071
LLG Fault - IEC60909 Method at the Following Times
Bus Name Pre Fault Initial Peak Short 0.5 Cycle 1 Cycle 3 Cycle 5 cycle Std
Voltage Symmetric Circuit Symmetric Symmetric Symmetric Symmetric Symmetric
al Current al SC al SC al SC al SC al SC
SCCurrent Current Current Current Current Current
AQC1 MCC 433 27496 56164 27496 27468 27439 27414 27414
AQC2 MCC 433 19362 34696 19362 19346 19330 19317 19317
COMMON BOP MCC 433 25180 49431 25180 25157 25132 25112 25112
Emergency MCC 433 24573 48786 24573 24550 24526 24506 24506
MLDB 433 23607 45299 23607 23583 23558 23537 23537
MPDB 433 26230 52186 26230 26205 26178 26156 26156
PH1 MCC 433 26110 52607 26110 26084 26057 26035 26035
PH2 MCC 433 24573 48786 24573 24550 24526 24506 24506
Turbine MCC 433 20915 40163 20915 20898 20880 20865 20865
 GRID RSEB RASULPURA GSS

GRID CPP
IC_AVVNL

PTR_IC

POWER TR

BD1

3
LC-1 MAIN DISTRIBUTION BOARD LC-4 CEMENT MILL SUBSTATION
MAIN SUBSTATION

LC4_IC
LC1_IC
LC1-EB BUS LC4 BUS

LC1_IC2 LC4_OG_CMSF1 LC4_OG_CMSF2 LC4_OG_SP LC4_OG_CMMD1 LC4_OG_CMMD2 LC4_OG_CM1 LC4_OG_CMV1 LC4_OG_CMV2 LC4_TIE LC4_OG_CM2 LC4_OG_PD1A LC4_OG_PD1B LC4_OG_PD2A LC4_OG_PD2B 175 LC4_OG_COMP

P-CMDRIVE-1
LC1-CPP BUS

P-CMDRIVE-2

P-VFD-TRAFO1

P-VFD-TRAFO2

P-TRAFO-2

P-COMP-TR2
P-TRAFO-1
11 12 19 27 28 35 36 43 44 51 52 60

Cement Mill CD Trafo 1

Cement Mill CD Trafo 2

20

P-CMSF1

P-CMSF2

123

P-RP1-M1

P-RP1-M2

P-RP2-M1

176
P-RP2-M2
151
TR1_ CMTMILL

TR2_CMTMILL

TR1_COMP
I I I I I I I I
LC1_OG_CAP1 LC1_OG_LC2 29 LC1_OG_LC3 LC1_OG_CAP2 CMSF1 CMSF2 CMD1 CMD2 ROLLER P1M1 ROLLER P1M2 ROLLER P2M1 ROLLER P2M2
LC1_OG_LC4
2 3 2 3

P-APFC-2
P-APFC-1

P-KCSS-IC1

P-CMSS-IC1
P-RMSS-IC1

P_CM1 VFD IC1

BD1_COMP1
P_CM1 VFD IC2

P_CM2 VFD IC2

CAP1 CAP2

P_CM2 VFD IC1

CM2 LINE UP VFD PANEL
LC-2 RAW MILL SUBSTATION CM1 LINE UP VFD PANEL LC-3 KILN & COOLER SUBSTATION COMP PANEL 1
390 449 402 471 531
CM1_LU_BUS A CM2_LU_BUS A
LC2_IC LC3_IC LC3 BUS COMP PNL1
LC2 BUS 534 538 542 546 550 554 558 562
CM1_LU_BUS B CM2_LU_BUS B
LC2_OG_SP1 LC2_IC1 LC2_OG_RMMM LC2_OG_RMFM LC2_OG_RM1 LC2_OG_RM2 LC2_OG_CM LC2_OG_CMMM LC2_OG_PH LC2_OG_CMCD LC2_OG_BH LC2_TIE LC2_OG_SP2 LC3_OG_LTG LC3_OG_CF2 LC3_OG_SP LC3_OG_CF1 LC3_OG_KCF LC3_OG_KILN LC3_TIE LC03_OG_COMP
533 537 541 545 549 553 557 561

P-VFD-TR1

P-COMP-TR1
61 62 436 437 441 442 446 447 452 453 458 459 463 464 468 469
P-TRAFO1

P-TRAFO2

P-TR-CM2

P-TR-PF1/2

P-TR-PF2/2

COOLER FANS CD TRAFO 1

COOLER FANS CD TRAFO 2
P-LGT-TR1
P-CMM-M-1
P-RMFM

KILN & C00LER TRAFO

49

P-RMMM

P-TR-BHF

P-TIE

112

P-TR-VFD2

196

206

P-DIST-TR1

P-CM-TIE
COAL Mill CD Trafo 1

CD.TRAFO -PHFAN

399 435 440 445 451 457 462 467

CD TRAFO BHF

TR1_KILNCOOLER
POWER FROM WHR

TF1_COALMILL

TR2_COMP
TF1_RM

TF2_RM

TR1_LTG
I I I
RMMM RMFM CMMM
2 3 2 3 2 3 2 3 2 3 2 3
P-CMM-M-2

P-CMM-M-3

641 640

P_COALM1 VFD IC2

BD1_CoalMill

P_COALM1 VFD IC1

P CLR FN TR2 IC2

67

BD2_RM

P CLR FN TR1 IC2

BD1_RM

BD2_COMP
RAW MILL LT PANEL COAL LINE UP VFD PANEL
RM_IC1 RM_IC2 CLU_VFD_IC1 CLU_VFD_IC2 COOLER FANS LINE UP VFD PANEL 2
BC_RM

700 716
RAW MILL BUS A RAW MILL BUS B
848 CF2_LU_BUS A

OG1_RM OG2_RM OG3_RM OG4_RM OG5_RM OG6_RM OG8_RM OG9_RM OG10_RM OG11_RM OG12_RM OG13_RM OG14_RM OG15_RM OG16_RM OG17_RM OG18_RM OG19_RM OG20_RM OG21_RM OG22_RM OG23_RM OG24_RM OG25_RM OG26_RM COMP PANEL 2
OG7_RM 884

849 CF2_LU_BUS B

P CLR FN TR1 IC1

COMP PNL2

P CLR FN TR2 IC1

829 830 833 834 743 744 738 739 733 734 728 729 723 724 703 704 708 709 713 714 720 718 887 891 895 899 903 907 911 915
BD-CM1

BD-CM2

828 832 742 737 732 727 722 702 707 712 751 886 890 894 898 902 906 910 914

644 660 ESP FAN VFD611

PANEL
COOLER FANS LINE UP VFD PANEL 1 ESP_FAN_IC
CF1_LU_BUS A ESPF_BUS A
CEMENT MILL LT PANEL
324 326
354

CEMENT MILL BUS A CEMENT MILL BUS B ESPF_BUS B

CF1_LU_BUS B

386 328 330 332 334 336 338 340 342 344 346 348 350 352 355 357 359 361 363 365 367 369 371 373 375 377 379 387 388 389
696 697 691 692 686 687681 682 676 677 671 672 647 648 652 653 657 658 668 666 615 616 621 622 626 627

695 690 685 680 675 670 646 651 656 699 614 620 625

BD_KILN COOLER
BD_LTG
KILN COOLER LT PANEL 568
934
KILN COOLER BUS
LTG PANEL 609 607 603 601 599 597 595 593 591 589 587 585 583 581 579 577 483
605 575
LTGPNL_IC
TG LIGHTING BUS
GEN
931 499 503 507 511 515 519 527
523

498 502 506 510 514 518 522 526

GT

755
COAL MILL LT PANEL
CMLTP_IC

PTR2 COAL MILL PCC

323 291 293 295 297 299 301 303 305 307 309 311 313 315 317

758

11kV HT PANEL 11kV HV PNL

WHR_IC Ik" : 16580.6A
Vp: 11000 V

WHR_SP WHR_OG5 WHR_OG4 WHR_OG3 WHR_OG2 WHR_OG1

769

779

GET1 GET2

REV. DATE ECO# DWN APP DESCRIPTION

773

783

WONDER CEMENT/SIEMENS LTD

415 V LT SWITCH BOARD 415 LTBD BUS A 415 LTBD BUS B

775 Ik" : 32506.82A
Electrical One-Line Diagram for
818 Ik" : 32506.82A
Vp: 433 V
820

Vp: 433 V

778 786 787 788 789 790 791 792 793 794 795 796 797 798 799 800 801 802 803 804 805 806 807 808 809 810 811 812 813 814 815 816 Co-ordination study-SHORT CIRCUIT
CURRENTS IN WHR PANELS
CAB:PH1

CAB:TURBINE

CAB:EMER

CAB:MPDB

CAB:COMMON

CAB:PH2
CAB:AQC1

CAB:MLDB

CAB:AQC2

DR AW N BY/D ATE:
DW G No.: REV.

PH1 MCC Turbine MCC Emergency MCC MPDB AQC1 MCC MLDB PH2 MCC AQC2 MCC
Ik" : 26764.27A Ik" : 22397.42A Ik" : 25539.13A Ik" : 26884.69A Ik" : 27819.1A Ik" : 24546.07A Ik" : 25539.13A Ik" : 19664.35A
ENG . AP P./D AT E:

Vp: 433 V Vp: 433 V Vp: 433 V Vp: 433 V Vp: 433 V COMMON BOP MCC
Vp: 433 V Vp: 433 V Vp: 433 V
Ik" : 26070.6A MFG. APP ./DATE:
PAR T No.:

Vp: 433 V
SCALE: DW G SI ZE:
 Setting Calculation for Distribution Transformers 2500 kVA at WHR

11 kV 433 V

150/1A 4000 Amps

2500 kVA
Transformer capacity PT 2500 kVA
Primary Voltage Vp 11 kV
Secondary Voltage Vs 0.433 kV
Transformer HV side CT details CTHV 150/1
Turns Ratio CTRP 150
Transformer LV side ACB rating 4000
Percentage Impedance of Transformer Z 7.00%
Fault Current at 11 kV Bus 12752 Amps
Fault current at 0.433 kV Bus 36424 Amps
Transformer HV side current as per name plate 131.21 Amps
Relay drop off Ratio 0.95
HV Pick up Current 1.1 x HV Currrent/ Drop off ratio
=1.1 x 131.21/0.95
151.93
Transformer HV side CT Secondary Pick up Current Isfl 1.01
IDMT setting at 11 kV side 1
Setting proposed on HV side Ip 1
Curve Extreme Inverse
Transformer LV side current as per name plate 3333.43
Relay drop off Ratio 0.95
LV Pick up Current 1.1 x LV Currrent/ Drop off ratio
=1.1 x3333.43/0.95
3859.76
Transformer LV side CT Secondary Pick up Current =3859.76/4000
Relay setting for over current 0.96
Setting proposed on LV side Ip 1
Fault current at 0.433kV Bus as per report,for MINIMUM SOURCE Fault 36424.00 Amps
HV side current due to fault at 0.433 kV bus 1433.78 Amps
HV side CT Secondary current due to fault at 0.433kV bus 9.56 Amps
HV side Current fault at Transformer HV side 12752.00
HV side CT current due to fault at Transformer HV side 85.01 Amps
Setting proposed on HV side relay I>> 9.56x 1.2=11.47 Amps
Setting proposed on HV side relay I>> 11.50
Setting proposed on LV side relay I>> 6
 Setting Details for WHR PCC1
Location of Device Sevice ID Breaker Set Phase Current Settings Ground Current Settings
device description Current In
OVERLOAD PROTECTION Short-time delayed short-circuit protection Instantaneous short-circuit protection Ground-fault protection
and release
SETTING Long time Primary Setting range time lag Setting Short time Primary Setting range Short time Setting range Instantaneous Primary Setting range Operating Primary Setting range Delay time
RANGE IR=In Pick up Current for time-lag setting in sec Pick up Current for delay delay in sec Ii = In ... Current Current of the current Current of the delay tg in ms
X Current 2 range Isd Current time tsd in (Tsd) in ms setting (I3) operating setting Ig time tg in ms
class tR at I t
setting (I1) = In ... Settint (Isd) ms current Ig

1F1 630A ACC FAN (110KW) 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

2F1 630A SPARE 630 0.4-0.45-0.5- 1 630 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

3F1 4000A INCOMER 4000 0.4-0.45-0.5- 1 4000 2-3.5-5.5-8- 3.5 1.25-1.5-2- 4 16000 100-200- 100 1.5-2.2-3-4- 6 24000 A-B-C-D-E A 100-200- 100
ACB,ETU45B 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 6-8-10-12 300-400-500
0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

CAG 14 relay for Incomer to be set at 10%

4F1 1000A AQC-1 MCC 1000 0.4-0.45-0.5- 1 1000 2-3.5-5.5-8- 2 1.25-1.5-2- 4 4000 100-200- 100 11 11 11000 A-B-C-D-E A 100-200- 100
ACB,ETU22 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

5F1 630A ACC FAN 11 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 1.5-10 6 3780 A-B-C-D-E A 100-200- 100
MCCB,ETU5 (110 kW SOFT Starter) 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

6F1 630A Spare 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 1.5-10 6 3780 A-B-C-D-E A 100-200- 100
MCCB,ETU5 (110 kW SOFT Starter) 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

7F1 630A BFP-2 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

8F1 630A MPDB 630 0.4-0.45-0.5- 1 630 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

9F1 630A CEP PUMP 1 630 0.4-0.45-0.5- 0.55 346.5 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

10F1 630A ACC FAN 1 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

11F1 630A ACC FAN 2 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

12F1 630A ACC FAN 3 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

13F1 630A ACC FAN4 630 0.4-0.45-0.5- 1 630 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0
Location of Device Sevice ID Breaker Set Phase Current Settings Ground Current Settings
device description Current In
OVERLOAD PROTECTION Short-time delayed short-circuit protection Instantaneous short-circuit protection Ground-fault protection
and release
SETTING Long time Primary Setting range time lag Setting Short time Primary Setting range Short time Setting range Instantaneous Primary Setting range Operating Primary Setting range Delay time
RANGE IR=In Pick up Current for time-lag setting in sec Pick up Current for delay delay in sec Ii = In ... Current Current of the current Current of the delay tg in ms
X Current 2 range Isd Current time tsd in (Tsd) in ms setting (I3) operating setting Ig time tg in ms
class tR at I t
setting (I1) = In ... Settint (Isd) ms current Ig

14F1 400A PH1 MCC 400 0.4-0.45-0.5- 1 400 2-3.5-5.5-8- 2 1.25-1.5-2- 4 1600 100-200- 100 1.5-15 10 4000 A-B-C-D-E A 100-200- 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

14F2 400A SPARE 400 0.4-0.45-0.5- 1 400 2-3.5-5.5-8- 2 1.25-1.5-2- 4 1600 100-200- 100 1.5-15 10 4000 A-B-C-D-E A 100-200- 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

15F1 400A EMERGENCY MCC 400 0.4-0.45-0.5- 1 400 2-3.5-5.5-8- 2 1.5-2-2.5-3- 4 1600 100-200- 100 1.5-15 10 4000 0.6/1.0 x in 0.6 240 100/300 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 4-5-6-7-8- 300-400
60 0.63-0.7-0.8- 25-30 s 10 xIR
0.9-0.95-1.0

15F2 400A TURBINE & ACC MCC 400 0.4-0.45-0.5- 0.8 320 2-3.5-5.5-8- 2 1.5-2-2.5-3- 4 1280 100-200- 100 1.5-15 11 4400 0.6/1.0 x in 0.6 240 100/300 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 4-5-6-7-8- 300-400
60 0.63-0.7-0.8- 25-30 s 10 xIR
0.9-0.95-1.0

16F1 4000A BUSCOUPLER 4000 0.4-0.45-0.5- 0.9 3600 2-3.5-5.5-8- 3.5 1.25-1.5-2- 3 12000 100-200- 100 1.5-2.2-3-4- 4 16000 A-B-C-D-E A 100-200- 100
ACB,ETU45B 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 6-8-10-12 300-400-500
0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

17F1 4000A INCOMER 2 4000 0.4-0.45-0.5- 1 4000 2-3.5-5.5-8- 3.5 1.25-1.5-2- 4 16000 100-200- 100 1.5-2.2-3-4- 6 24000 A-B-C-D-E A 100-200- 100
ACB,ETU45B 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 6-8-10-12 300-400-500
0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

CAG 14 relay for Incomer to be set at 10%

18F1 630A COMMON & BOP MCC 630 0.4-0.45-0.5- 1 630 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

18F2 630A SPARE 630 0.4-0.45-0.5- 0.8 504 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

19F1 1000 A SPARE 1000 0.4-0.45-0.5- 1 1000 2-3.5-5.5-8- 2 1.5-2-2.5-3- 4 4000 100-200- 100 - - - 0.6/1.0 x in 0.6 600 100/300 100
ACB,ETU 37 0.55-0.6- 10-14-17-21- 4-5-6-7-8- 300-400
WT 0.63-0.7-0.8- 25-30 s 10 xIR
0.9-0.95-1.0

20F1 630A ACC FAN -12 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 1.5-10 10 6300 A-B-C-D-E A 100-200- 100
MCCB,ETU5 (110kW Soft Starter) 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

21F1 630A ACC FAN -6 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

22F1 630A ACC FAN -7 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

23F1 630A ACC FAN -8 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0
Location of Device Sevice ID Breaker Set Phase Current Settings Ground Current Settings
device description Current In
OVERLOAD PROTECTION Short-time delayed short-circuit protection Instantaneous short-circuit protection Ground-fault protection
and release
SETTING Long time Primary Setting range time lag Setting Short time Primary Setting range Short time Setting range Instantaneous Primary Setting range Operating Primary Setting range Delay time
RANGE IR=In Pick up Current for time-lag setting in sec Pick up Current for delay delay in sec Ii = In ... Current Current of the current Current of the delay tg in ms
X Current 2 range Isd Current time tsd in (Tsd) in ms setting (I3) operating setting Ig time tg in ms
class tR at I t
setting (I1) = In ... Settint (Isd) ms current Ig

24F1 630A ACC FAN -9 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

25F1 630A ACC FAN -10 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

26F1 630A CEP PUMP 2 630 0.4-0.45-0.5- 0.55 346.5 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

27F1 630A BFP-1 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

28F1 630A BFP-3 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

29F1 630A SPARE 630 0.4-0.45-0.5- 1 630 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

30F1 400A PH-2 MCC 400 0.4-0.45-0.5- 1 400 2-3.5-5.5-8- 2 1.25-1.5-2- 4 1600 100-200- 100 1.5-15 11 4400 A-B-C-D-E A 100-200- 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

30F2 400A MLDB 400 0.4-0.45-0.5- 1 400 2-3.5-5.5-8- 2 1.25-1.5-2- 4 1600 100-200- 100 1.5-15 11 4400 A-B-C-D-E A 100-200- 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

31F1 250A AQC-2 MCC 250 0.4-0.45-0.5- 0.7 175 2-3.5-5.5-8- 2 1.25-1.5-2- 4 1000 100-200- 100 11 11 2750 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

31F2 400A SPARE 400 0.4-0.45-0.5- 1 400 2-3.5-5.5-8- 2 1.25-1.5-2- 4 1600 100-200- 100 1.5-15 10 4000 A-B-C-D-E A 100-200- 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0
 Setting Details for WHR PCC1
Location of Device Sevice ID Breaker Set Phase Current Settings Ground Current Settings
device description Current In
OVERLOAD PROTECTION Short-time delayed short-circuit protection Instantaneous short-circuit protection Ground-fault protection
and release
SETTING Long time Primary Setting range time lag Setting Short time Primary Setting range Short time Setting range Instantaneous Primary Setting range Operating Primary Setting range Delay time
RANGE IR=In Pick up Current for time-lag setting in sec Pick up Current for delay delay in sec Ii = In ... Current Current of the current Current of the delay tg in ms
X Current 2 range Isd Current time tsd in (Tsd) in ms setting (I3) operating setting Ig time tg in ms
class tR at I t
setting (I1) = In ... Settint (Isd) ms current Ig

1F1 630A ACC FAN (110KW) 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

2F1 630A SPARE 630 0.4-0.45-0.5- 1 630 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

3F1 4000A INCOMER 4000 0.4-0.45-0.5- 1 4000 2-3.5-5.5-8- 3.5 1.25-1.5-2- 4 16000 100-200- 100 1.5-2.2-3-4- 6 24000 A-B-C-D-E A 100-200- 100
ACB,ETU45B 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 6-8-10-12 300-400-500
0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

4F1 1000A AQC-1 MCC 1000 0.4-0.45-0.5- 1 1000 2-3.5-5.5-8- 2 1.25-1.5-2- 4 4000 100-200- 100 11 11 11000 A-B-C-D-E A 100-200- 100
ACB,ETU22 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

5F1 630A ACC FAN 11 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 1.5-10 6 3780 A-B-C-D-E A 100-200- 100
MCCB,ETU5 (110 kW SOFT Starter) 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

6F1 630A Spare 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 1.5-10 6 3780 A-B-C-D-E A 100-200- 100
MCCB,ETU5 (110 kW SOFT Starter) 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

7F1 630A BFP-2 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

8F1 630A MPDB 630 0.4-0.45-0.5- 1 630 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

9F1 630A MPDB 630 0.4-0.45-0.5- 0.55 346.5 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

10F1 630A ACC FAN 1 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

11F1 630A ACC FAN 2 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

12F1 630A ACC FAN 3 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

13F1 630A ACC FAN4 630 0.4-0.45-0.5- 1 630 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0
Location of Device Sevice ID Breaker Set Phase Current Settings Ground Current Settings
device description Current In
OVERLOAD PROTECTION Short-time delayed short-circuit protection Instantaneous short-circuit protection Ground-fault protection
and release
SETTING Long time Primary Setting range time lag Setting Short time Primary Setting range Short time Setting range Instantaneous Primary Setting range Operating Primary Setting range Delay time
RANGE IR=In Pick up Current for time-lag setting in sec Pick up Current for delay delay in sec Ii = In ... Current Current of the current Current of the delay tg in ms
X Current 2 range Isd Current time tsd in (Tsd) in ms setting (I3) operating setting Ig time tg in ms
class tR at I t
setting (I1) = In ... Settint (Isd) ms current Ig

14F1 400A PH1 MCC 400 0.4-0.45-0.5- 1 400 2-3.5-5.5-8- 2 1.25-1.5-2- 4 1600 100-200- 100 1.5-15 10 4000 A-B-C-D-E A 100-200- 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

14F2 400A SPARE 400 0.4-0.45-0.5- 1 400 2-3.5-5.5-8- 2 1.25-1.5-2- 4 1600 100-200- 100 1.5-15 10 4000 A-B-C-D-E A 100-200- 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

15F1 400A EMERGENCY MCC 400 0.4-0.45-0.5- 1 400 2-3.5-5.5-8- 2 1.5-2-2.5-3- 4 1600 100-200- 100 1.5-15 10 4000 0.6/1.0 x in 0.6 240 100/300 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 4-5-6-7-8- 300-400
60 0.63-0.7-0.8- 25-30 s 10 xIR
0.9-0.95-1.0

15F2 400A TURBINE & ACC MCC 400 0.4-0.45-0.5- 0.8 320 2-3.5-5.5-8- 2 1.5-2-2.5-3- 4 1280 100-200- 100 1.5-15 11 4400 0.6/1.0 x in 0.6 240 100/300 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 4-5-6-7-8- 300-400
60 0.63-0.7-0.8- 25-30 s 10 xIR
0.9-0.95-1.0

16F1 4000A BUSCOUPLER 4000 0.4-0.45-0.5- 1 4000 2-3.5-5.5-8- 3.5 1.25-1.5-2- 4 16000 100-200- 100 1.5-2.2-3-4- 6 24000 A-B-C-D-E A 100-200- 100
ACB,ETU45B 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 6-8-10-12 300-400-500
0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

17F1 4000A INCOMER 2 4000 0.4-0.45-0.5- 1 4000 2-3.5-5.5-8- 3.5 1.25-1.5-2- 4 16000 100-200- 100 1.5-2.2-3-4- 6 24000 A-B-C-D-E A 100-200- 100
ACB,ETU45B 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 6-8-10-12 300-400-500
0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

18F1 630A COMMON & BOP MCC 630 0.4-0.45-0.5- 1 630 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

18F2 630A SPARE 630 0.4-0.45-0.5- 0.8 504 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

19F1 1000 A SPARE 1000 0.4-0.45-0.5- 1 1000 2-3.5-5.5-8- 2 1.5-2-2.5-3- 4 4000 100-200- 100 - - - 0.6/1.0 x in 0.6 600 100/300 100
ACB,ETU 37 0.55-0.6- 10-14-17-21- 4-5-6-7-8- 300-400
WT 0.63-0.7-0.8- 25-30 s 10 xIR
0.9-0.95-1.0

20F1 630A ACC FAN -12 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 1.5-10 10 6300 A-B-C-D-E A 100-200- 100
MCCB,ETU5 (110kW Soft Starter) 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

21F1 630A ACC FAN -6 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

22F1 630A ACC FAN -7 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

23F1 630A ACC FAN -8 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0
Location of Device Sevice ID Breaker Set Phase Current Settings Ground Current Settings
device description Current In
OVERLOAD PROTECTION Short-time delayed short-circuit protection Instantaneous short-circuit protection Ground-fault protection
and release
SETTING Long time Primary Setting range time lag Setting Short time Primary Setting range Short time Setting range Instantaneous Primary Setting range Operating Primary Setting range Delay time
RANGE IR=In Pick up Current for time-lag setting in sec Pick up Current for delay delay in sec Ii = In ... Current Current of the current Current of the delay tg in ms
X Current 2 range Isd Current time tsd in (Tsd) in ms setting (I3) operating setting Ig time tg in ms
class tR at I t
setting (I1) = In ... Settint (Isd) ms current Ig

24F1 630A ACC FAN -9 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

25F1 630A ACC FAN -10 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

26F1 630A CEP PUMP 2 630 0.4-0.45-0.5- 0.55 346.5 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

27F1 630A BFP-1 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

28F1 630A BFP-3 630 0.4-0.45-0.5- 0.4 252 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

29F1 630A SPARE 630 0.4-0.45-0.5- 1 630 2-3.5-5.5-8- 2 1.25-1.5-2- 4 2520 100-200- 100 11 11 6930 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

30F1 400A PH-2 MCC 400 0.4-0.45-0.5- 1 400 2-3.5-5.5-8- 2 1.25-1.5-2- 4 1600 100-200- 100 1.5-15 11 4400 A-B-C-D-E A 100-200- 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

30F2 400A MLDB 400 0.4-0.45-0.5- 1 400 2-3.5-5.5-8- 2 1.25-1.5-2- 4 1600 100-200- 100 1.5-15 11 4400 A-B-C-D-E A 100-200- 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

31F1 250A AQC-2 MCC 250 0.4-0.45-0.5- 0.7 175 2-3.5-5.5-8- 2 1.25-1.5-2- 4 1000 100-200- 100 11 11 2750 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

31F2 400A SPARE 400 0.4-0.45-0.5- 1 400 2-3.5-5.5-8- 2 1.25-1.5-2- 4 1600 100-200- 100 1.5-15 10 4000 A-B-C-D-E A 100-200- 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0
 Setting Details for AQC1-MCC1
Location of Device Sevice ID Breaker Set Phase Current Settings Ground Current Settings
device description Current In
OVERLOAD PROTECTION Short-time delayed short-circuit protection Instantaneous short-circuit protection Ground-fault protection
and release
SETTING Long time Primary Setting range time lag Setting Short time Primary Setting range Short time Setting range Instantaneous Primary Setting range Operating Primary Setting range Delay time
RANGE IR=In Pick up Current for time-lag setting in sec Pick up Current for delay delay in sec Ii = In ... Current Current of the current Current of the delay tg in ms
X Current 2 range Isd Current time tsd in (Tsd) in ms setting (I3) operating setting Ig time tg in ms
class tR at I t
setting (I1) = In ... Settint (Isd) ms current Ig

1F1 1000A INCOMER 1000 0.4-0.45-0.5- 0.8 800 2-3.5-5.5-8- 3.5 1.25-1.5-2- 4 4000 100-200- 100 1.5-2.2-3-4- 6 6000 A-B-C-D-E A 100-200- 100
ACB,ETU37 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 6-8-10-12 300-400-500
WT 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

2F1 800A BOOSTER FAN 800 0.4-0.45-0.5- 0.8 640 2-3.5-5.5-8- 3.5 1.25-1.5-2- 4 3200 100-200- 100 1.5-2.2-3-4- 6 4800 A-B-C-D-E A 100-200- 100
ACB,ETU37 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 6-8-10-12 300-400-500
WT 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

3F1 800A BOOSTER FAN SPARE 800 0.4-0.45-0.5- 0.8 640 2-3.5-5.5-8- 3.5 1.25-1.5-2- 4 3200 100-200- 100 1.5-2.2-3-4- 6 4800 A-B-C-D-E A 100-200- 100
ACB,ETU37 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 6-8-10-12 300-400-500
WT 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0
Setting Details for AQC1-MCC1 (Motor Feeders only)
Motor Feeder Settings
Location Type of Feeder Description SFU Drive Motor OLR Settings
of device Starter rating/FU rating in full Load Range in Set
SE rating kW Phase Amps Current
current in Amps
4F2 DOL LP STEAM START 63/6 0.37 1.15 0.3 - 3 1.25
STARTER UP VENT
5F1 DOL RAV-1 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
5F2 DOL LP STEAM MSSV BY 63/2 0.06 0.2 0.3 - 3 0.30
STARTER PASS MOV
5F3 DOL CBD MOV (HP DRUM) 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
5F4 DOL HP FEED WATER 63/16 2.2 5 2.4-25 5.50
STARTER LCV UPSTEAM ISO
VALVE MOV
6F1 DOL COMMON DOSING 63/6 0.75 2 0.3 - 3 2.20
STARTER TANKAGITATOR TO
HP SD & LP SD
6F2 DOL DRAIN VALVE MOV 63/2 0.06 0.2 0.3 - 3 0.30
STARTER AT LP
6F3 DOL CBD MOV (LP DRUM) 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
6F4 DOL HP FEED WATER 63/16 2.2 5 2.4-25 5.50
STARTER BYE PASS LCV
UPSTEAM ISO
VALVE MOV
7F2 DOL HP DOSING PUMP 1 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
7F3 DOL GEARED MOTOR 63/16 2.2 5 2.4-25 5.50
STARTER DCC1
7F4 DOL LP FEED WATER 63/2 0.12 0.4 0.3 - 3 0.45
STARTER LCV UPSTEAM ISO
VALVE MOV
7F5 DOL HP STEAM START 63/16 1.1 2.5 2.4-25 2.65
STARTER UP VENT
8F2 DOL HP DOSING PUMP 2 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
8F3 DOL GEARED MOTOR 63/16 2.2 5 2.4-25 5.50
STARTER DCC2
8F4 DOL IBD MOV (HP DRUM) 63/4 0.18 0.6 0.3 - 3 0.70
STARTER
8F5 DOL ECONOMIZED 63/16 1.1 2.5 2.4-25 2.65
STARTER BYPASS MOV
9F2 DOL HP DOSING PUMP 1 63/6 0.37 1.15 0.3 - 3 1.25
STARTER TO LP
9F3 DOL GEARED MOTOR 63/16 2.2 5 2.4-25 5.50
STARTER DCC3
9F4 DOL CPH INLET MOV 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
9F5 DOL FRESH AIR DAMPER 63/16 1.5 3.5 2.4-25 3.80
STARTER
10F2 DOL HP DOSING PUMP 2 63/6 0.37 1.15 0.3 - 3 1.25
STARTER TO LP
10F3 DOL GEARED MOTOR 63/16 2.2 5 2.4-25 5.50
STARTER DCC4
10F4 DOL CPH OUTLET MOV 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
10F5 DOL HP STEAM MSSV 63/16 2.2 5 2.4-25 5.50
STARTER MOV
11F3 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
11F4 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
11F5 DOL LP STEAM MSSV 63/6 0.55 1.4 0.3 - 3 1.55
STARTER MOV
11R3 DOL RAV-2 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
11R4 DOL CPH BYPASS MOV 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
11R5 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
10R2 DOL RAV-3 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
10R3 DOL SPARE 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
9R1 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
9R2 DOL IBD MOV (LP DRUM) 63/4 0.18 0.6 0.3 - 3 0.70
STARTER
9R3 DOL SPARE 63/16 1.1 2.5 2.4-25 2.65
STARTER
9R4 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
8R1 DOL RAV-4 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
8R3 DOL RAV-5 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
8R4 DOL SPARE 63/6 0.75 2 0.3 - 3 2.20
STARTER
8R5 DOL SPARE 63/16 1.1 2.5 2.4-25 2.65
STARTER
7R3 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
7R4 DOL LP FEED WATER 63/2 0.12 0.4 0.3 - 3 0.45
STARTER BYPASS LCV
UPSTEAM ISO
VALVE MOV
7R5 DOL SPARE 63/16 1.1 2.5 2.4-25 2.65
STARTER
6R2 DOL SPARE 63/6 0.75 2 0.3 - 3 2.20
STARTER
6R4 DOL HP STEAM MSSC 63/2 0.12 0.4 0.3 - 3 0.45
STARTER BYPASS MOV
6R5 DOL ISO MOV AT PH#1 63/16 1.1 2.5 2.4-25 2.65
STARTER OUTLET
 Setting Details for Ph1 Boiler-MCC2
Location of Device Sevice ID Breaker Set Phase Current Settings Ground Current Settings
device description Current In OVERLOAD PROTECTION Short-time delayed short-circuit protection Instantaneous short-circuit protection Ground-fault protection
and release
SETTING Long time Primary Setting range time lag Setting Short time Primary Setting range Short time Setting range Instantaneous Primary Setting range Operating Primary Setting range Delay time
RANGE IR=In Pick up Current for time-lag setting in sec Pick up Current for delay delay in sec Ii = In ... Current Current of the current Current of the delay tg in ms
X Current 2 range Isd Current time tsd in (Tsd) in ms setting (I3) operating setting Ig time tg in ms
class tR at I t
setting (I1) = In ... Settint (Isd) ms current Ig

1F3 400A Incomer 400 0.4-0.45-0.5- 0.8 320 2-3.5-5.5-8- 3.5 1.25-1.5-2- 4 1600 100-200- 100 1.5-15 10 4000 A-B-C-D-E A 100-200- 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0
Setting Details for Ph1 Boiler-MCC2 (Motor Feeders only)
Motor Feeder Settings
Location Type of Feeder Description SFU Drive Motor OLR Settings
of device Starter rating/FU rating in full Load Range in Set
SE rating kW Phase Amps Current
current in Amps
2F1 DOL HP DOSING PUMP-1 63/6 0.37 1.15 0.3 - 3 1.25
STARTER TO HP SD
2F2 DOL RAV3 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
3F1 DOL RAV4 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
3F2 DOL LP RC PUMP1 125/80 18.5 35 10-100 38.00
STARTER
3F3 DOL HP FEED WATER 63/16 1.1 2.5 2.4-25 2.65
STARTER LCV UPSTEAM ISO
VALVE MOV
3F4 DOL HP RC PUMP1 250/125 30 55 10-100 61.00
STARTER
4F1 DOL RAV-5 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
4F2 DOL DRAIN VALVE MOV 63/2 0.06 0.2 0.3 - 3 0.30
STARTER AT LP
4F3 DOL CBD MOV (HP DRUM) 63/4 0.18 0.6 0.3 - 3 0.70
STARTER
4F4 DOL LP STEAM MSSV 63/16 2.2 5 2.4-25 5.50
STARTER MOV
5F1 DOL RAV9 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
5F2 DOL LP STEAM MSSV 63/2 0.12 0.4 0.3 - 3 0.45
STARTER BYPASS MOV
5F3 DOL IBD MOV (HP DRUM) 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
5F4 DOL HP STEAM MSSV 63/16 2.2 5 2.4-25 5.50
STARTER MOV
6F1 DOL RAV-10 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
6F2 DOL HAMMERING 63/16 1.5 3.5 2.4-25 3.90
STARTER MOTOR 1
6F3 DOL HAMMERING 63/16 1.5 3.5 2.4-25 3.90
STARTER MOTOR 2
6F4 DOL GEARED MOTOR 125/25 3.7 7.5 2.4-25 8.25
STARTER DCC-2
6F5 DOL CBD MOV (LP DRUM) 63/4 0.18 0.6 0.3 - 3 0.70
STARTER
7F2 DOL GEARED MOTOR 125/25 3.7 7.5 2.4-25 8.25
STARTER DCC-3
7F3 DOL LP RC PUMP2 125/80 18.5 35 10-100 38.00
STARTER
7F4 DOL IBD MOV (LP DRUM) 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
7F5 DOL LP FEED WATER 63/4 0.18 0.6 0.3 - 3 0.70
STARTER LCV UPSTEAM ISO
VALVE MOV
8F1 DOL HP DOSING PUMP-2 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
8F2 DOL COMMON DOSING 63/6 0.75 2 0.3 - 3 2.20
STARTER TANK AGITATOR TO
HP SD
8F4 DOL HAMMERING 63/16 1.5 3.5 2.4-25 3.90
STARTER MOTOR 3
8F5 DOL LP FEED WATER 63/4 0.18 0.6 0.3 - 3 0.70
STARTER BYPASS LCV
UPSTEAM ISO
VALVE MOV
9F1 DOL HAMMERING 63/16 1.5 3.5 2.4-25 3.90
STARTER MOTOR 4
9F2 DOL GEARED MOTOR 125/25 3.7 7.5 2.4-25 8.25
STARTER DCC-1
9F3 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
9F4 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
9F5 DOL HP FEED WATER 63/16 1.1 2.5 2.4-25 2.65
STARTER BYPASS LCV UP
STEAM ISO VALVE
MOV
9R3 DOL HP DOSING PUMP 1 63/6 0.37 1.15 0.3 - 3 1.25
STARTER TO LP SD
9R4 DOL HP STEAM START 63/6 0.55 1.4 0.3 - 3 1.55
STARTER UP VENT UPSTEAM
ISO MOV
9R5 DOL LP STEAM START 63/6 0.55 1.4 0.3 - 3 1.55
STARTER UP VENT UPSTEAM
ISO MOV
8R2 DOL RAV-10 63/6 0.75 2 0.3 - 3 2.20
STARTER
8R5 DOL SPARE 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
7R1 DOL HP DOSING PUMP-2 63/6 0.37 1.15 0.3 - 3 1.25
STARTER LP SD
7R2 DOL RAV-2 63/6 0.75 2 0.3 - 3 2.20
STARTER
7R3 DOL RAV 13 125/25 3.7 7.5 2.4-25 8.25
STARTER
7R5 DOL SPARE 63/4 0.18 0.6 0.3 - 3 0.70
STARTER
6R2 DOL RAV-11 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
6R3 DOL RAV-12 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
5R2 DOL GEARED MOTOR 125/80 18.5 35 10-100 38.00
STARTER DCC 4
5R3 DOL HP STEAM MSSV 63/2 0.12 0.4 0.3 - 3 0.45
STARTER BYPASS MOV
5R4 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
4R1 DOL SPARE 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
4R2 DOL RAV-6 63/6 0.75 2 0.3 - 3 2.20
STARTER
4R3 DOL SPARE 63/16 1.5 3.5 2.4-25 3.90
STARTER
4R4 DOL DRAIN VALVE MOV 63/2 0.06 0.2 0.3 - 3 0.30
STARTER AT HP
3R1 DOL SPARE 125/80 18.5 35 10-100 38.00
STARTER
3R2 DOL SPARE 125/25 3.7 7.5 2.4-25 8.25
STARTER
3R3 DOL SPARE 63/16 1.1 2.5 2.4-25 2.65
STARTER
3R4 DOL HP RC PUMP2 250/125 30 55 10-100 61.00
STARTER
2R2 DOL RAV-7 63/6 0.75 2 0.3 - 3 2.20
STARTER
2R3 DOL RAV-8 63/6 0.75 2 0.3 - 3 2.20
STARTER
2R4 DOL SPARE 63/16 1.1 2.5 2.4-25 2.65
STARTER
2R5 DOL SPARE 250/125 30 55 10-100 61.00
STARTER
1R1 DOL SPARE 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
1R2 DOL SPARE 63/6 0.75 2 0.3 - 3 2.20
STARTER
 Setting Details for AQC2-MCC3
Location of Device Sevice ID Breaker Set Phase Current Settings Ground Current Settings
device description Current In
OVERLOAD PROTECTION Short-time delayed short-circuit protection Instantaneous short-circuit protection Ground-fault protection
and release
SETTING Long time Primary Setting range time lag Setting Short time Primary Setting range Short time Setting range Instantaneous Primary Setting range Operating Primary Setting range Delay time
RANGE IR=In Pick up Current for time-lag setting in sec Pick up Current for delay delay in sec Ii = In ... Current Current of the current Current of the delay tg in ms
X Current 2 range Isd Current time tsd in (Tsd) in ms setting (I3) operating setting Ig time tg in ms
class tR at I t
setting (I1) = In ... Settint (Isd) ms current Ig

1F4 250A Incomer 250 0.4-0.45-0.5- 0.65 162.5 2-3.5-5.5-8- 3.5 1.25-1.5-2- 3 750 100-200- 100 1.5-15 10 2500 A-B-C-D-E A 100-200- 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0
Setting Details for AQC2-MCC3 (Motor Feeders only)
Motor Feeder Settings
Location Type of Feeder Description SFU Drive Motor OLR Settings
of device Starter rating/FU rating in full Load Range in Set
SE rating kW Phase Amps Current
current in Amps
2F1 DOL HP DOSING PUMP-1 63/6 0.37 1.15 0.3 - 3 1.25
STARTER TO HP SD
2F2 DOL GEARED MOTOR 63/16 2.2 5 2.4-25 5.50
STARTER DCC-2
3F1 DOL HP DOSING PUMP-2 63/6 0.37 1.15 0.3 - 3 1.25
STARTER TO HP SD
3F2 DOL LP STEAM MSSV 63/2 0.06 0.2 0.3 - 3 0.30
STARTER BYPASS MOV
3F3 DOL CBD MOV (HP DRUM) 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
3F4 DOL HP STEAM START 63/16 1.1 2.5 2.4-25 2.65
STARTER UP VENT
4F1 DOL HP DOSING PUMP-1 63/6 0.37 1.15 0.3 - 3 1.25
STARTER TO LP SD
4F2 DOL CBD MOV (LP DRUM) 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
4F3 DOL LP FEED WATER 63/2 0.12 0.4 0.3 - 3 0.45
STARTER LCV UPSTEAM ISO
VALVE MOV
4F4 DOL ECONOMIZED 63/16 1.1 2.5 2.4-25 2.65
STARTER BYPASS MOV
5F1 DOL HP DOSING PUMP-2 63/6 0.37 1.15 0.3 - 3 1.25
STARTER TO LP SD
5F2 DOL LP FEED WATER 63/2 0.12 0.4 0.3 - 3 0.45
STARTER LCV UPSTEAM ISO
VALVE MOV
5F3 DOL SPARE 63/16 1.1 2.5 2.4-25 2.65
STARTER
5F4 DOL HP FEED WATER 63/16 2.2 5 2.4-25 5.50
STARTER LCV UPTEAM ISO
VALVE MOV
6F1 DOL GEARED MOTOR 63/16 2.2 5 2.4-25 5.50
STARTER DCC-1
6F2 DOL IBD MOV (HP DRUM) 63/4 0.18 0.6 0.3 - 3 0.70
STARTER
6F3 DOL LP STEAM START 63/6 0.37 1.15 0.3 - 3 1.25
STARTER UP VENT UPSTEAM
ISO MOV
6F4 DOL HP FEED WATER 63/16 2.2 5 2.4-25 5.50
STARTER LCV UPTEAM ISO
VALVE MOV
7F3 DOL GEARED MOTOR 63/16 2.2 5 2.4-25 5.50
STARTER DCC3
7F4 DOL CPH INLET MOV 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
7F5 DOL HP STEAM MSSV 63/16 2.2 5 2.4-25 5.50
STARTER MOV
8F2 DOL RAV-2 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
8F3 DOL RAV-1 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
8F4 DOL LP STEAM MSSV 63/6 0.55 1.4 0.3 - 3 1.55
STARTER MOV
8F5 DOL CPH OUTLET MOV 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
8R4 DOL CPH BYPASS MOV 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
8R5 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
7R1 DOL COMMON DOSING 63/6 0.75 2 0.3 - 3 2.20
STARTER TANK AGITATOR TO
HP SD
7R2 DOL SPARE 63/16 1.1 2.5 2.4-25 2.65
STARTER
7R3 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
7R4 DOL FRESH AIR DAMPER 63/16 2.2 5 2.4-25 5.50
STARTER
6R2 DOL SPARE 63/6 0.75 2 0.3 - 3 2.20
STARTER
6R3 DOL SPARE 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
5R2 DOL RAV-3 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
5R3 DOL SPARE 63/6 0.75 2 0.3 - 3 2.20
STARTER
5R4 DOL IBD MOV (LP DRUM) 63/4 0.18 0.6 0.3 - 3 0.70
STARTER
5R5 DOL FRESH AIR DAMPER 63/16 1.5 3.5 2.4-25 3.90
STARTER
4R2 DOL RAV-4 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
4R3 DOL GEARED MOTOR 63/16 2.2 5 2.4-25 5.50
STARTER DCC-4
4R4 DOL HP STEAM MSSV 63/2 0.12 0.4 0.3 - 3 0.45
STARTER BYPASS MOV
4R5 DOL SPARE 63/16 1.1 2.5 2.4-25 2.65
STARTER
3R2 DOL RAV-5 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
3R3 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
3R4 DOL DRAIN VALVE MOV 63/2 0.06 0.2 0.3 - 3 0.30
STARTER AT LP
3R5 DOL ISO MOV AT PH#2 63/16 1.1 2.5 2.4-25 2.65
STARTER OUTLET
2R2 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
2R4 DOL DRAIN VALVE MOV 63/2 0.06 0.2 0.3 - 3 0.30
STARTER AT HP
2R5 DOL SPARE 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
1R2 DOL ISO MOV AT AQC#2 63/6 0.55 1.4 0.3 - 3 1.55
STARTER OUTLET
 Setting Details for TURBINE -MCC5
Location of Device Sevice ID Breaker Set Phase Current Settings Ground Current Settings
device description Current In OVERLOAD PROTECTION Short-time delayed short-circuit protection Instantaneous short-circuit protection Ground-fault protection
and release
SETTING Long time Primary Setting range time lag Setting Short time Primary Setting range Short time Setting range Instantaneous Primary Setting range Operating Primary Setting range Delay time
RANGE IR=In Pick up Current for time-lag setting in sec Pick up Current for delay delay in sec Ii = In ... Current Current of the current Current of the delay tg in ms
X Current 2 range Isd Current time tsd in (Tsd) in ms setting (I3) operating setting Ig time tg in ms
class tR at I t
setting (I1) = In ... Settint (Isd) ms current Ig

1F3 400A Incomer 400 0.4-0.45-0.5- 0.75 300 2-3.5-5.5-8- 3.5 1.25-1.5-2- 3 1200 100-200- 100 1.5-15 10 4000 A-B-C-D-E A 100-200- 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0
Setting Details for TURBINE -MCC5 (Motor Feeders only)
Motor Feeder Settings
Location Type of Feeder Description SFU Drive Motor OLR Settings
of device Starter rating/FU rating in full Load Range in Set
SE rating kW Phase Amps Current
current in Amps
1F2 DOL DRAIN PUMP 63/16 2.2 5 2.4-25 5.50
STARTER DISCHARGE
2F1 DOL HP DOSING PUMP-1 125/32 5.5 11 2.4-25 12.00
STARTER
2F2 DOL TRANSFER OIL 63/16 1.5 3.5 2.4-25 3.90
STARTER PUMP DRIVE MOTOR

3F2 DOL M O GATE VALVE 1 63/2 0.06 0.2 0.3 - 3 0.30

STARTER
3F3 DOL M O GATE VALVE 8 63/16 1.1 2.5 2.4-25 2.65
STARTER
3F4 DOL DRAIN PUMP 63/16 2.2 5 2.4-25 5.50
STARTER DISCHARGE ISO
MOV
4F1 DOL DRAIN PUMP MOTOR 125/32 5.5 11 2.4-25 12.00
STARTER
4F2 DOL M O GATE VALVE 2 63/2 0.06 0.2 0.3 - 3 0.30
STARTER
4F3 DOL CEP DISC 63/16 2.2 5 2.4-25 5.50
STARTER ISOLATION MOV
4F4 DOL CEP DISC 63/16 2.2 5 2.4-25 5.50
STARTER ISOLATION MOV
5F2 DOL M O GATE VALVE 3 63/2 0.06 0.2 0.3 - 3 0.30
STARTER
5F3 DOL DUMP SPRAY 63/16 2.2 5 2.4-25 5.50
STARTER CONTROL CV ISO
MOV
5F4 DOL DUMP SPRAY 63/16 2.2 5 2.4-25 5.50
STARTER CONTROL CV
BYPASS ISO MOV
6F2 DOL DP MIN 63/16 2.2 5 2.4-25 5.50
STARTER RECIRCULATION CV
ISO MOV
6F3 DOL M O GATE VALVE 4 63/2 0.06 0.2 0.3 - 3 0.30
STARTER
6F4 DOL DP MIN 63/16 2.2 5 2.4-25 5.50
STARTER RECIRCULATION CV
BYPASS ISO MOV

7F2 DOL MAKE UP WATER 63/16 2.2 5 2.4-25 5.50

STARTER LINE CVISO MOV
7F3 DOL M O GATE VALVE 5 63/2 0.06 0.2 0.3 - 3 0.30
STARTER
7F4 DOL M O GATE VALVE 6 63/2 0.06 0.2 0.3 - 3 0.30
STARTER
8F2 DOL M O GATE VALVE 7 63/2 0.06 0.2 0.3 - 3 0.30
STARTER
8F3 DOL MAKE UP WATER 63/16 2.2 5 2.4-25 5.50
STARTER LINE CV BYPASS
ISO MOV
8F4 DOL CEP MIN 63/16 2.2 5 2.4-25 5.50
STARTER RECIRCULATION CV
BYPASS ISO MOV

9F1 DOL CEP MIN 63/16 2.2 5 2.4-25 5.50

STARTER RECIRCULATION CV
ISO MOV
9F2 DOL MOTIVE STEAM OIL 63/16 2.2 5 2.4-25 5.50
STARTER MOV
9F3 DOL MOTIVE STEAM OIL 63/16 2.2 5 2.4-25 5.50
STARTER MOV
11F1 DOL GSCF-1 125/25 3.7 7.5 2.4-25 8.25
STARTER
11F2 DOL BYPASS MOV AT 63/4 0.18 0.6 0.3 - 3 0.70
STARTER BFP#2
11F3 DOL WARM UP VENT 63/6 0.37 1.15 0.3 - 3 1.25
STARTER LINE
11F4 DOL MOV AT BFP#1 63/16 1.25 2.8 2.4-25 3.05
STARTER
12F2 DOL SPARE 125/32 5.5 11 2.4-25 12.00
STARTER
12F3 DOL SPARE 63/16 1.5 3.5 2.4-25 3.90
STARTER
12F4 DOL ISO MOV NEAR 63/16 1.1 2.5 2.4-25 2.65
STARTER HEADER AT LP
STEAM
12F5 DOL ISO MOV NEAR 63/16 1.1 2.5 2.4-25 2.65
STARTER HEADER AT LP
STEAM
12R2 DOL BYPASS MOV AT 63/4 0.18 0.6 0.3 - 3 0.70
STARTER BFP#1
12R3 DOL WARM UP VENT 63/6 0.37 1.15 0.3 - 3 1.25
STARTER LINE
12R4 DOL BYPASS MOV AT 63/4 0.18 0.6 0.3 - 3 0.70
STARTER BFP#3
11R3 DOL LP DOSING PUMP 1 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
11R4 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
11R5 DOL MOV AT BFP#1 63/4 0.18 0.6 0.3 - 3 0.70
STARTER
10R3 DOL BYPASS MOV AT 63/4 0.18 0.6 0.3 - 3 0.70
STARTER BFP#1
10R4 DOL MOV AT BFP#2 63/4 0.18 0.6 0.3 - 3 0.70
STARTER
9R3 DOL BYPASS MOV AT 63/4 0.18 0.6 0.3 - 3 0.70
STARTER BFP#2
9R4 DOL MOV AT BFP#2 63/16 1.25 2.8 2.4-25 3.05
STARTER
8R1 DOL LP DOSING PUMP 2 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
8R2 DOL MOV AT BFP#3 63/4 0.18 0.6 0.3 - 3 0.70
STARTER
8R3 DOL BYPASS MOV AT 63/4 0.18 0.6 0.3 - 3 0.70
STARTER BFP#3
8R4 DOL MOV AT BFP#3 63/16 1.25 2.8 2.4-25 3.05
STARTER
7R2 DOL MOTORISED DRAIN 63/2 0.06 0.2 0.3 - 3 0.30
STARTER VALVE MOV IN HP
STEAM LINE
7R3 DOL D/A LCV UPSTREAM 63/4 0.18 0.6 0.3 - 3 0.70
STARTER ISO VALVE MOV

7R4 DOL SPARE 63/6 0.37 1.15 0.3 - 3 1.25

STARTER
6R2 DOL MOTORISED DRAIN 63/2 0.06 0.2 0.3 - 3 0.30
STARTER VALVE MOV AT HP
6R3 DOL AQC#1 MAIN STEAM 63/16 1.1 2.5 2.4-25 2.65
STARTER LINE MOV
6R4 DOL SPARE 63/16 1.1 2.5 2.4-25 2.65
STARTER
5R1 DOL LP LOSING 63/6 0.75 2 0.3 - 3 2.20
STARTER AGITATOR
5R2 DOL AQC#1 MAIN STEAM 63/2 0.06 0.2 0.3 - 3 0.30
STARTER LINE MOV
5R3 DOL MOV IN LP DUMP 63/16 2.2 5 2.4-25 5.50
STARTER STEAM LINE
5R4 DOL MOV IN HP DUMP 63/16 2.2 5 2.4-25 5.50
STARTER STEAM LINE
4R3 DOL TURBINE MSSV 63/16 2.2 5 2.4-25 5.50
STARTER MOV AT HP STEAM
LINE
4R4 DOL AQC # 1 MAIN 63/2 0.06 0.2 0.3 - 3 0.30
STARTER STEAM LINE
3R1 DOL SPARE 63/6 0.75 2 0.3 - 3 2.20
STARTER
3R2 DOL TURBINE MSSV 63/16 2.2 5 2.4-25 5.50
STARTER MOV AT LP STEAM
LINE
3R3 DOL AQC # 1 MAIN 63/16 2.2 5 2.4-25 5.50
STARTER STEAM LINE
3R4 DOL TURBINE MSSV 63/2 0.06 0.2 0.3 - 3 0.30
STARTER MOV BYPASS MOV
AT HP STEAM LINE
2R2 DOL GSCF-2 125/25 3.7 7.5 2.4-25 8.25
STARTER
2R4 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
2R5 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
1R2 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
 Setting Details for Ph2 Boiler-MCC4
Location of Device Sevice ID Breaker Set Phase Current Settings Ground Current Settings
device description Current In OVERLOAD PROTECTION Short-time delayed short-circuit protection Instantaneous short-circuit protection Ground-fault protection
and release
SETTING Long time Primary Setting range time lag Setting Short time Primary Setting range Short time Setting range Instantaneous Primary Setting range Operating Primary Setting range Delay time
RANGE IR=In Pick up Current for time-lag setting in sec Pick up Current for delay delay in sec Ii = In ... Current Current of the current Current of the delay tg in ms
X Current 2 range Isd Current time tsd in (Tsd) in ms setting (I3) operating setting Ig time tg in ms
class tR at I t
setting (I1) = In ... Settint (Isd) ms current Ig

1F3 400A Incomer 400 0.4-0.45-0.5- 0.9 360 2-3.5-5.5-8- 3.5 1.25-1.5-2- 3 1200 100-200- 100 1.5-15 10 4000 A-B-C-D-E A 100-200- 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0
Setting Details for Ph2 Boiler-MCC4 (Motor Feeders only)
Motor Feeder Settings
Location Type of Feeder Description SFU Drive Motor OLR Settings
of device Starter rating/FU rating in full Load Range in Set
SE rating kW Phase Amps Current
current in Amps
1F1 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
1F2 DOL GEARED MOTOR 125/25 3.7 7.5 2.4-25 8.25
STARTER DCC-1
2F1 DOL HP DOSING PUMP-1 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
2F2 DOL GEARED MOTOR 125/25 3.7 7.5 2.4-25 8.25
STARTER DCC-2
3F1 DOL RAV3 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
3F2 DOL LP RC PUMP1 125/80 18.5 35 10-100 38.00
STARTER
3F3 DOL DRAIN VALVE MOV 63/2 0.06 0.2 0.3 - 3 0.30
STARTER AT LP
3F4 DOL HP RC PUMP1 250/125 30 55 10-100 61.00
STARTER
4F1 DOL RAV-4 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
4F2 DOL LP STEAM MSSV 63/2 0.12 0.4 0.3 - 3 0.45
STARTER BYPASS MOV
4F3 DOL CBD MOV (HP DRUM) 63/4 0.18 0.6 0.3 - 3 0.70
STARTER
4F4 DOL LP STEAM MSSV 63/16 2.2 5 2.4-25 5.50
STARTER MOV
5F1 DOL RAV5 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
5F2 DOL CBD MOV (LP DRUM) 63/4 0.18 0.6 0.3 - 3 0.70
STARTER
5F3 DOL DRAIN VALVE MOV 63/2 0.06 0.2 0.3 - 3 0.30
STARTER AT HP
5F4 DOL HP STEAM MSSV 63/16 2.2 5 2.4-25 5.50
STARTER MOV
6F1 DOL HAMMERING 63/16 1.5 3.5 2.4-25 3.90
STARTER MOTOR 1
6F2 DOL COMMON DOSING 63/6 0.75 2 0.3 - 3 2.20
STARTER TANK AGITATOR TO
HP SD
6F3 DOL GEARED MOTOR 125/25 3.7 7.5 2.4-25 8.25
STARTER DCC-3
6F4 DOL HP DOSING PUMP-2 63/6 0.37 1.15 0.3 - 3 1.25
STARTER
6F5 DOL LP FEED WATER 63/4 0.18 0.6 0.3 - 3 0.70
STARTER LCV UPSTEAM ISO
VALVE MOV
7F2 DOL HAMMERING 63/16 1.5 3.5 2.4-25 3.90
STARTER MOTOR 2
7F3 DOL HP DOSING PUMP-1 63/6 0.37 1.15 0.3 - 3 1.25
STARTER TO LP SD
7F4 DOL HAMMERING 63/16 1.5 3.5 2.4-25 3.90
STARTER MOTOR 3
7F5 DOL LP FEED WATER 63/4 0.18 0.6 0.3 - 3 0.70
STARTER LCV UPSTEAM ISO
VALVE MOV
8F2 DOL RAV 1 63/6 0.75 2 0.3 - 3 2.20
STARTER
8F3 DOL HAMMERING 63/16 1.5 3.5 2.4-25 3.90
STARTER MOTOR 4
8F4 DOL HP DOSING PUMP 2 63/6 0.37 1.15 0.3 - 3 1.25
STARTER TO LP SD
8F5 DOL IBD MOV (HP DRUM) 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
9F3 DOL LP RC PUMP 2 125/80 18.5 35 10-100 38.00
STARTER
9F4 DOL HP FEED WATER 63/16 1.1 2.5 2.4-25 2.65
STARTER BYPASS LCV UP
STEAM ISO VALVE
MOV
9R3 DOL HP STEAM START 63/6 0.55 1.4 0.3 - 3 1.55
STARTER UP VENT UPSTEAM
ISO MOV
9R1 DOL IBD MOV (LP DRUM) 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
8R1 DOL RAV-2 63/6 0.75 2 0.3 - 3 2.20
STARTER
8R2 DOL RAV-6 63/6 0.75 2 0.3 - 3 2.20
STARTER
8R3 DOL RAV 9 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
8R4 DOL RAV 10 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
8R5 DOL LP STEAM START 63/6 0.55 1.4 0.3 - 3 1.55
STARTER UP VENT UPSTEAM
ISO MOV
7R4 DOL SPARE 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
6R2 DOL RAV-11 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
6R3 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
6R4 DOL SPARE 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
6R5 DOL GEARED MOTOR 125/80 18.5 35 10-100 38.00
STARTER DCC 4
5R1 DOL RAV-7 63/6 0.75 2 0.3 - 3 2.20
STARTER
5R2 DOL HP FEED WATER 63/16 1.1 2.5 2.4-25 2.65
STARTER BYPASS LCV UP
STEAM ISO VALVE
MOV
5R3 DOL SPARE 63/4 0.18 0.6 0.3 - 3 0.70
STARTER
5R4 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
4R1 DOL RAV 12 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
4R2 DOL RAV-8 63/6 0.75 2 0.3 - 3 2.20
STARTER
4R3 DOL RAV 13 125/25 3.7 7.5 2.4-25 8.25
STARTER
4R4 DOL DRAIN VALVE MOV 63/2 0.06 0.2 0.3 - 3 0.30
STARTER AT HP
4R5 DOL HP STEAM MSSV 63/2 0.12 0.4 0.3 - 3 0.45
STARTER BYPASS MOV
3R2 DOL SPARE 125/25 3.7 7.5 2.4-25 8.25
STARTER
3R3 DOL SPARE 63/16 1.1 2.5 2.4-25 2.65
STARTER
3R4 DOL HP RC PUMP2 250/125 30 55 10-100 61.00
STARTER
2R1 DOL SPARE 63/6 0.75 2 0.3 - 3 2.20
STARTER
2R2 DOL SPARE 125/80 18.5 35 10-100 38.00
STARTER
2R3 DOL SPARE 63/16 1.1 2.5 2.4-25 2.65
STARTER
2R4 DOL SPARE 250/125 30 55 10-100 61.00
STARTER
1R1 DOL SPARE 63/6 0.55 1.4 0.3 - 3 1.55
STARTER
1R2 DOL SPARE 63/16 1.5 3.5 2.4-25 3.90
STARTER
 Setting Details for COMMON & BOP -MCC6
Location of Device Sevice ID Breaker Set Phase Current Settings Ground Current Settings
device description Current In OVERLOAD PROTECTION Short-time delayed short-circuit protection Instantaneous short-circuit protection Ground-fault protection
and release
SETTING Long time Primary Setting range time lag Setting Short time Primary Setting range Short time Setting range Instantaneous Primary Setting range Operating Primary Setting range Delay time
RANGE IR=In Pick up Current for time-lag setting in sec Pick up Current for delay delay in sec Ii = In ... Current Current of the current Current of the delay tg in ms
X Current 2 range Isd Current time tsd in (Tsd) in ms setting (I3) operating setting Ig time tg in ms
class tR at I t
setting (I1) = In ... Settint (Isd) ms current Ig

1F1 630A INCOMER 630 0.4-0.45-0.5- 0.95 598.5 2-3.5-5.5-8- 3.5 1.25-1.5-2- 3 1890 100-200- 100 1.5-2.2-3-4- 6 3780 A-B-C-D-E A 100-200- 100
ACB,ETU37 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 6-8-10-12 300-400-500
WT 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0
Setting Details for COMMON & BOP -MCC6 (Motor Feeders only)
Motor Feeder Settings
Location Type of Feeder Description SFU Drive Motor OLR Settings
of device Starter rating/FU rating in full Load Range in Set
SE rating kW Phase Amps Current
current in Amps
2F1 DOL SSF AIR BLOWER-1 63/16 1.5 3.5 2.4-25 3.90
STARTER
2F2 DOL DM WATER 125/25 4 8.25 2.4-25 9.00
STARTER TRANSFER PUMP 1
3F1 DOL AUX BOP PUMP 1 63/16 2.2 5 2.4-25 5.50
STARTER
3F2 DOL AUX BOP PUMP 1 63/16 2.2 5 2.4-25 5.50
STARTER
3F3 DOL ACW PUMP 1 400/250 90 165 20-200 182.00
STARTER
3F4 DOL DM WATER 125/25 4 8.25 2.4-25 9.00
STARTER TRANSFER PUMP 2
4F2 DOL MOV AFTER THE 63/16 1.1 2.5 2.4-25 2.65
STARTER ACW1
4F3 DOL ACW PUMP 1 400/250 90 165 20-200 182.00
STARTER
4F4 DOL CT FAN 1 125/63 15 28 10-100 31.00
STARTER
5F2 DOL CT FAN2 125/63 15 28 10-100 31.00
STARTER
5F3 DOL MOV AFTER THE 63/16 1.1 2.5 2.4-25 2.65
STARTER ACW2
5F4 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
6F1 DOL SSF AIR BLOWER-2 63/16 1.5 3.5 2.4-25 3.90
STARTER
6F2 DOL AUX BOP PUMP 3 63/16 2.2 5 2.4-25 5.50
STARTER
6F4 DOL SPARE 125/50 7.5 14 2.4-25 15.50
STARTER
6F5 DOL SPARE 125/63 15 28 10-100 31.00
STARTER
6R1 DOL CT FAN3 125/63 15 28 10-100 31.00
STARTER
6R3 DOL MOV AFTER THE 63/16 1.1 2.5 2.4-25 2.65
STARTER ACW3
6R4 DOL SPARE 63/16 1.1 2.5 2.4-25 2.65
STARTER
4R2 DOL AUX BOP PUMP 5 63/16 2.2 5 2.4-25 5.50
STARTER
4R3 DOL SPARE 400/250 90 165 20-200 182.00
STARTER
4R4 DOL AUX BOP PUMP 4 63/16 2.2 5 2.4-25 5.50
STARTER
3R1 DOL SSF BACKWASH 125/32 5.5 11 2.4-25 12.00
STARTER PUMP 1
3R2 DOL SSF BACKWASH 125/32 5.5 11 2.4-25 12.00
STARTER PUMP 1
3R5 DOL BOILER INITIAL FILL 125/50 7.5 14 2.4-25 15.50
STARTER PUMP
2R1 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
2R2 DOL SPARE 125/25 4 8.25 2.4-25 9.00
STARTER
 Setting Details for EMERGENCY -MCC 8
Location of Device Sevice ID Breaker Set Phase Current Settings Ground Current Settings
device description Current In OVERLOAD PROTECTION Short-time delayed short-circuit protection Instantaneous short-circuit protection Ground-fault protection
and release
SETTING Long time Primary Setting range time lag Setting Short time Primary Setting range Short time Setting range Instantaneous Primary Setting range Operating Primary Setting range Delay time
RANGE IR=In Pick up Current for time-lag setting in sec Pick up Current for delay delay in sec Ii = In ... Current Current of the current Current of the delay tg in ms
X Current 2 range Isd Current time tsd in (Tsd) in ms setting (I3) operating setting Ig time tg in ms
class tR at I t
setting (I1) = In ... Settint (Isd) ms current Ig

1F1 400A Incomer1 400 0.4-0.45-0.5- 0.8 320 2-3.5-5.5-8- 3.5 1.25-1.5-2- 3 1200 100-200- 100 1.5-15 10 4000 A-B-C-D-E A 100-200- 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

1F1 400A Incomer2 400 0.4-0.45-0.5- 0.8 320 2-3.5-5.5-8- 3.5 1.25-1.5-2- 3 1200 100-200- 100 1.5-15 11 4400 A-B-C-D-E A 100-200- 100
MCCB,ETU5 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
60 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0
Setting Details for EMERGENCY -MCC 8 (Motor Feeders only)
Motor Feeder Settings
Location Type of Feeder Description SFU Drive Motor OLR Settings
of device Starter rating/FU rating in full Load Range in Set
SE rating kW Phase Amps Current
current in Amps
3F1 DOL CRITICAL VALVE 3 63/16 2.2 5 2.4-25 5.50
STARTER
3F2 DOL CRITICAL VALVE1 63/16 2.2 5 2.4-25 5.50
STARTER
5F3 DOL CRITICAL VALVE2 125/25 3.7 7.5 2.4-25 8.25
STARTER
6F1 DOL OIL VAPOUR 63/6 0.37 1.15 0.3 - 3 1.25
STARTER EXTRACTION FAN
MOTOR
6F3 DOL SPARE 125/63 11 21 2.4-25 23.00
STARTER
6F4 DOL SPARE 400/250 75 135 20-200 149.00
STARTER
7R2 DOL SPARE 63/16 1.5 3.5 2.4-25 3.90
STARTER
5R2 DOL JACKING OIL PUMP 125/63 11 21 2.4-25 23.00
STARTER DRIVE
5R3 DOL LUB OIL PUMP 400/250 75 135 20-200 149.00
STARTER DRIVE MOTOR 1
5R4 DOL LUB OIL PUMP 400/250 75 135 20-200 149.00
STARTER DRIVE MOTOR 1
4R1 DOL CRITICAL VALVE -4 63/16 2.2 5 2.4-25 5.50
STARTER
4R2 DOL SPARE 125/25 3.7 7.5 2.4-25 8.25
STARTER
3R1 DOL OIL VAPOUR 63/6 0.37 1.15 0.3 - 3 1.25
STARTER EXTRACTION FAN
MOTOR-2
3R2 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
 Setting Details for Damper AQC1 Line 1 -MCC
Location of Device Sevice ID Breaker Set Phase Current Settings Ground Current Settings
device description Current In
OVERLOAD PROTECTION Short-time delayed short-circuit protection Instantaneous short-circuit protection Ground-fault protection
and release
SETTING Long time Primary Setting range time lag Setting Short time Primary Setting range Short time Setting range Instantaneous Primary Setting range Operating Primary Setting range Delay time
RANGE IR=In Pick up Current for time-lag setting in sec Pick up Current for delay delay in sec Ii = In ... Current Current of the current Current of the delay tg in ms
X Current 2 range Isd Current time tsd in (Tsd) in ms setting (I3) operating setting Ig time tg in ms
class tR at I t
setting (I1) = In ... Settint (Isd) ms current Ig

1F3 125A Incomer 125 0.4-0.45-0.5- 0.8 100 2-3.5-5.5-8- 3.5 1.25-1.5-2- 4 500 100-200- 100 11 11 1375 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

Setting Details for Damper AQC1 Line 1 -MCC (Motor Feeders only)
Motor Feeder Settings
Location Type of Feeder Description SFU Drive Motor OLR Settings
of device Starter rating/FU rating in full Load Range in Set
SE rating kW Phase Amps Current
current in Amps
1F2 DOL MULTI LOUVER 63/16 2.2 in Amps5 2.4-25 5.50
STARTER DAMPER AT AQC #1
BYPASS
2F2 DOL FRESH AIR DAMPER 63/16 2.2 5 2.4-25 5.50
STARTER FOR AQC#1

3F3 DOL GUILLOTINE 125/25 3.7 7.5 2.4-25 8.25

STARTER DAMPER AT AQC #1
OUTLET
3F4 DOL SPARE 63/16 2.2 5 2.4-25 5.50
STARTER
3R3 DOL GUILLOTINE 125/32 5.5 11 2.4-25 12.00
STARTER DAMPER
3R4 DOL FRESH AIR DAMPER 63/16 1.5 3.5 2.4-25 3.90
STARTER FOR AQC#1

2R3 DOL BYPASS MOV AT 63/4 0.25 0.8 0.3 - 3 0.90

STARTER BFP#2
1R3 DOL SPARE 125/32 5.5 11 2.4-25 12.00
STARTER
 Setting Details for AQC2 Line 2 Damper MCC
Location of Device Sevice ID Breaker Set Phase Current Settings Ground Current Settings
device description Current In
OVERLOAD PROTECTION Short-time delayed short-circuit protection Instantaneous short-circuit protection Ground-fault protection
and release
SETTING Long time Primary Setting range time lag Setting Short time Primary Setting range Short time Setting range Instantaneous Primary Setting range Operating Primary Setting range Delay time
RANGE IR=In Pick up Current for time-lag setting in sec Pick up Current for delay delay in sec Ii = In ... Current Current of the current Current of the delay tg in ms
X Current 2 range Isd Current time tsd in (Tsd) in ms setting (I3) operating setting Ig time tg in ms
class tR at I t
setting (I1) = In ... Settint (Isd) ms current Ig

1F3 125A Incomer 125 0.4-0.45-0.5- 0.9 112.5 2-3.5-5.5-8- 3.5 1.25-1.5-2- 4 500 100-200- 100 11 11 1375 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

Setting Details for AQC2 Line 2 Damper MCC (Motor Feeders only)
Motor Feeder Settings
Location Type of Feeder Description SFU Drive Motor OLR Settings
of device Starter rating/FU rating in full Load Range in Set
SE rating kW Phase Amps Current
current in Amps
1F2 DOL MULTILOUVER 63/16 2.2 in Amps5 2.4-25 5.50
STARTER DAMPER AQC#2
BYPASS
2F2 DOL FRESH AIR DAMPER 63/16 2.2 5 2.4-25 5.50
STARTER FOR AQC #2

3F3 DOL GUILLOTINE 125/25 3.7 7.5 2.4-25 8.25

STARTER DAMPER AT AQC#2
OUTLET
3F4 DOL GUILLOTINE 125/32 5.5 11 2.4-25 12.00
STARTER DAMPER AT AQC#2
INLET
3R3 DOL SPARE 125/25 3.7 7.5 2.4-25 8.25
STARTER
3R4 DOL FRESH AIR DAMPER 63/16 1.5 3.5 2.4-25 3.90
STARTER FOR AQC #2

2R3 DOL SPARE 125/32 5.5 11 2.4-25 12.00

STARTER
 Setting Details for Ph2 Line 2 Damper MCC
Location of Device Sevice ID Breaker Set Phase Current Settings Ground Current Settings
device description Current In OVERLOAD PROTECTION Short-time delayed short-circuit protection Instantaneous short-circuit protection Ground-fault protection
and release
SETTING Long time Primary Setting range time lag Setting Short time Primary Setting range Short time Setting range Instantaneous Primary Setting range Operating Primary Setting range Delay time
RANGE IR=In Pick up Current for time-lag setting in sec Pick up Current for delay delay in sec Ii = In ... Current Current of the current Current of the delay tg in ms
X Current 2 range Isd Current time tsd in (Tsd) in ms setting (I3) operating setting Ig time tg in ms
class tR at I t
setting (I1) = In ... Settint (Isd) ms current Ig

1F3 125A Incomer 125 0.4-0.45-0.5- 0.9 112.5 2-3.5-5.5-8- 3.5 1.25-1.5-2- 4 500 100-200- 100 11 11 1375 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

Setting Details for Ph2 Line 2 Damper MCC (Motor Feeders only)
Motor Feeder Settings
Location Type of Feeder Description SFU Drive Motor OLR Settings
of device Starter rating/FU rating in full Load Range in Set
SE rating kW Phase Amps Current
current in Amps
1F2 DOL GUILLOTINE 125/63 15 in Amps28 20-200 31.00
STARTER DAMPER AT PH#2
INLET
2F2 DOL GUILLOTINE 125/63 15 28 20-200 31.00
STARTER DAMPER AT PH#2
INLET
2R2 DOL GUILLOTINE 125/25 3.7 7.5 2.4-25 8.25
STARTER DAMPER AT PH#2
BYPASS
2R3 DOL SPARE 125/63 15 28 20-200 31.00
STARTER
1R3 DOL SPARE 125/25 3.7 7.5 2.4-25 8.25
STARTER
 Setting Details for DAMPER MCC PH1 LINE1
Location of Device Sevice ID Breaker Set Phase Current Settings Ground Current Settings
device description Current In
OVERLOAD PROTECTION Short-time delayed short-circuit protection Instantaneous short-circuit protection Ground-fault protection
and release
SETTING Long time Primary Setting range time lag Setting Short time Primary Setting range Short time Setting range Instantaneous Primary Setting range Operating Primary Setting range Delay time
RANGE IR=In Pick up Current for time-lag setting in sec Pick up Current for delay delay in sec Ii = In ... Current Current of the current Current of the delay tg in ms
X Current 2 range Isd Current time tsd in (Tsd) in ms setting (I3) operating setting Ig time tg in ms
class tR at I t
setting (I1) = In ... Settint (Isd) ms current Ig

1F3 125A Incomer 125 0.4-0.45-0.5- 0.9 112.5 2-3.5-5.5-8- 3.5 1.25-1.5-2- 4 500 100-200- 100 11 11 1375 A-B-C-D-E A 100-200- 100
MCCB,ETU2 0.55-0.6- 10-14-17-21- 2.5-3-4-6-8- 300-400 300-400-500
2 0.65-0.7-0.8- 25-30 s 10-12 x In
0.9-1.0

Setting Details for DAMPER MCC PH1 LINE1 (Motor Feeders only)
Motor Feeder Settings
Location Type of Feeder Description SFU Drive Motor OLR Settings
of device Starter rating/FU rating in full Load Range in Set
SE rating kW Phase Amps Current
current in Amps
1F2 DOL GUILLOTINE 125/63 15 in Amps28 20-200 31.00
STARTER DAMPER AT PH#1
INLET
2R3 DOL GUILLOTINE 125/25 3.7 7.5 2.4-25 8.25
STARTER DAMPER AT PH#1
BYPASS
1R3 DOL SPARE 125/63 15 28 20-200 31.00
STARTER
1R2 DOL SPARE 125/25 3.7 7.5 2.4-25 8.25
STARTER