Scribd
Upload
202 views

Assignment 2 Solid Mechanic

This document is an assignment for a Solid Mechanics 1 course at Universiti Tun Hussein Onn Malaysia. It contains two questions for students to answer. Question 1 involves calculating the neutral axis, second moment of area, and maximum bending stress of a T-shaped beam under a uniform load. Question 2 has two parts: (a) calculating the angle of twist of an axle under a torque load, and (b) finding the maximum shearing stresses and rotational angle of a connected steel and bronze shaft under load. The assignment is due on November 21st, 2016 and covers material from the previous 1 week of the course.

Uploaded by

satah91
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
202 views

Assignment 2 Solid Mechanic

This document is an assignment for a Solid Mechanics 1 course at Universiti Tun Hussein Onn Malaysia. It contains two questions for students to answer. Question 1 involves calculating the neutral axis, second moment of area, and maximum bending stress of a T-shaped beam under a uniform load. Question 2 has two parts: (a) calculating the angle of twist of an axle under a torque load, and (b) finding the maximum shearing stresses and rotational angle of a connected steel and bronze shaft under load. The assignment is due on November 21st, 2016 and covers material from the previous 1 week of the course.

Uploaded by

satah91
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

UNIVERSITI TUN HUSSEIN ONN MALAYSIA

ASSIGNMENT 2
SEMESTER I
SESSION 2016/2017

COURSE NAME : SOLID MECHANICS 1

COURSE CODE : BDA 10903

PROGRAM : BACHELOR OF MECHANICAL


ENGINEERING

SUBMISSION DATE : 21st NOVEMBER 2016

DURATION : 1 WEEKS

INSTRUCTION : ANSWER ALL QUESTIONS

THIS PAPER CONTAINS FOUR (4) PAGES

CONFIDENTIAL
BDA 10903

ANSWER ALL QUESTIONS

Q1 Cross section of T shape beam being simply supported at the end of the beam as shown in
Figure Q1 carry uniform distributed load of 45kN/m at A to C. Determine:

(i) The neutral axis from the bottom surface of the beam (6 Marks)
(ii) The second moment of area (I) (7 Marks)
(iii) The maximum bending stress of the beam (10 Marks)

Q2 (a) The A-36 steel axle is made from tubes AB and CD and a solid section BC as shown in
Figure Q2(a). It is supported on smooth bearings that allow it to rotate freely. If the ends
are subjected to 85Nm torques, determine the angle of twist of the end A relative to end D.
The tubes have an outer diameter of 30 mm and an inner diameter of 20 mm. The solid
section has a diameter of 40 mm and G=75 GPa.

(7 marks)
Q2 (b) Two 80 mm diameter solid circular steel (G=80 GPa ) and bronze (G= 45 GPa) shafts are
rigidly connected and supported as shown in Figure Q2(b). Determine :
(i) The maximum shearing stress in the steel segment
(ii) The maximum shearing stress in the bronze segment
(iii) The rotation of a section at B with respect to its no load position
(18 marks)

2
BDA 10903

ASSIGNMENT 2
SEMESTER / SESI : SEMESTER I//2016/17 PROGRAMME : BDD
COURSE NAME : SOLID MECHANICS 1 COURSE CODE : BDA 10903

45 kN/m

16 kN.m 50 mm
C
A B

200mm
2.4 m 1.2 m

80 mm 40 mm 80 mm

Figure Q1

Figure Q2 (a)
BDA 10903

ASSIGNMENT 2
SEMESTER / SESI : SEMESTER I/2016/17 PROGRAMME : BDD
COURSE NAME : SOLID MECHANICS 1 COURSE CODE : BDA 10903

Figure Q2 (b)

You might also like