CCNA_200-125_88q_by _PenPineappleApplePen

Number: 200-125
Passing Score: 810
Time Limit: 120 min
File Version: 1.11

Brought to you by:

PenPineappleApplePen-
The NEW exam is said that it has 67/58 Questions and this is not complete but may will help.
Extracted from @m.. @joe @9xx @PASS @afi and includes 2 Drag and Drops (about cables and ipv6)
Study also the 4 sims (DHCP,RIPv2,OSPF,ACL)
Study also this from @m.. (*new question was tcp/ip what is included in internet: choose from:
aplication,session,presenation,data etc
*which mode is capabile with trunk,access,desirable : choose from: trunk, access, auto, desirable
*sth like when we use split horizon)
And please if you are not confident enough, study both 62q and 545q

After your exam please try to share your experience and questions to : http://www.9tut.com/share-your-ccna-v3-
0-experience/
AND PLEASE IF YOU KNOW MORE PLEASE SHARE!

TO WHOEVER USE THIS, GOODLUCK!

PPAP

QUESTION 1
Which technology supports the stateless assignment of IPv6 addresses?

A. DNS
B. DHCPv6
C. DHCP
D. autoconfiguration

Correct Answer: BD
Section: (none)
Explanation

Explanation/Reference:

QUESTION 2
What are two requirements for an HSRP group? (Choose two.)

A. exactly one active router

B. one or more standby routers
C. one or more backup virtual routers
D. exactly one standby active router
E. exactly one backup virtual router

Correct Answer: AB
Section: (none)
Explanation

Explanation/Reference:

QUESTION 3
After you configure the Loopback0 interface, which command can you enter to verify the status of
the interface and determine whether fast switching is enabled?

A. Router#show ip interface loopback 0

B. Router#show run
C. Router#show interface loopback 0
D. Router#show ip interface brief

Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:

QUESTION 4
Which command sequence can you enter to create VLAN 20 and assign it to an interface on a
switch?

A. Switch(config)#vlan 20
Switch(config)#Interface gig x/y
 Switch(config-if)#switchport access vlan 20
B. Switch(config)#Interface gig x/y
Switch(config-if)#vlan 20
Switch(config-vlan)#switchport access vlan 20
C. Switch(config)#vlan 20
Switch(config)#Interface vlan 20
Switch(config-if)#switchport trunk native vlan 20
D. Switch(config)#vlan 20
Switch(config)#Interface vlan 20
Switch(config-if)#switchport access vlan 20
E. Switch(config)#vlan 20
Switch(config)#Interface vlan 20
Switch(config-if)#switchport trunk allowed vlan 20

Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:

QUESTION 5
Which three commands can you use to set a router boot image? (Choose three.)

A. Router(config)# boot system flash c4500-p-mz.121-20.bin

B. Router(config)# boot system tftp c7300-js-mz.122-33.SB8a.bin
C. Router(config)#boot system rom c7301-advipservicesk9-mz.124-24.T4.bin
D. Router> boot flash:c180x-adventerprisek9-mz-124-6T.bin
E. Router(config)#boot flash:c180x-adventerprisek9-mz-124-6T.bin
F. Router(config)#boot bootldr bootflash:c4500-jk9s-mz.122-23f.bin

Correct Answer: ABC

Section: (none)
Explanation

Explanation/Reference:

QUESTION 6
Which two statements about IPv6 and routing protocols are true? (Choose two.)

A. Link-local addresses are used to form routing adjacencies.

B. OSPFv3 was developed to support IPv6 routing.
C. EIGRP, OSPF, and BGP are the only routing protocols that support IPv6.
D. Loopback addresses are used to form routing adjacencies.
E. EIGRPv3 was developed to support IPv6 routing.

Correct Answer: AB
Section: (none)
Explanation

Explanation/Reference:

QUESTION 7
If primary and secondary root switches with priority 16384 both experience catastrophic losses,
which tertiary switch can take over?

A. a switch with priority 20480

B. a switch with priority 8192
C. a switch with priority 4096
D. a switch with priority 12288

Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:

QUESTION 8
Which two statements about late collisions are true? (Choose two.)

A. They may indicate a duplex mismatch.

B. By definition, they occur after the 512th bit of the frame has been transmitted.
C. They indicate received frames that did not pass the FCS match.
D. They are frames that exceed 1518 bytes.
E. They occur when CRC errors and interference occur on the cable.

Correct Answer: AB
Section: (none)
Explanation

Explanation/Reference:

QUESTION 9
Which command can you enter to set the default route for all traffic to an interface?

A. router(config)#ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/1

B. router(config)#ip route 0.0.0.0 255.255.255.255 GigabitEthernet0/1
C. router(config-router)#default-information originate
D. router(config-router)#default-information originate always

Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:

QUESTION 10
Which two spanning-tree port states does RSTP combine to allow faster convergence? (Choose two.)

A. blocking
B. listening
C. learning
D. forwarding
E. discarding
Correct Answer: AB
Section: (none)
Explanation

Explanation/Reference:

QUESTION 11
If a router has four interfaces and each interface is connected to four switches, how many
broadcast domains are present on the router?

A. 1
B. 2
C. 4
D. 8

Correct Answer: C
Section: (none)
Explanation

Explanation/Reference:

QUESTION 12
The left describes the types of cables, while the right describes the purposes of the cables.
Drag the items on the left to the proper locations. (Not all items can be used.)
(THE COMMUNITY SHARED THAT THERE IS ANOTHER OPTION SO STUDY ALL OF WHAT THIS
CABLES ARE FOR)

Select and Place:

Correct Answer:

Section: (none)
Explanation

Explanation/Reference:

QUESTION 13
Match the items on the left with appropriate OSI layer on the right. (Not all options are used.)
Select and Place:
Correct Answer:
Section: (none)
Explanation

Explanation/Reference:

QUESTION 14
Which command enables IPv6 forwarding on a Cisco router?

A. ipv6 local
B. ipv6 host
C. ipv6 unicast-routing
D. ipv6 neighbor

Correct Answer: C
Section: (none)
Explanation

Explanation/Reference:
QUESTION 15
Refer to the exhibit. What is the most appropriate summarization for these routes?

A. 10.0.0.0 /21
B. 10.0.0.0 /22
C. 10.0.0.0 /23
D. 10.0.0.0 /24

Correct Answer: B
Section: (none)
Explanation

Explanation/Reference:
The 10.0.0.0/22 subnet mask will include the 10.0.0.0, 10.0.1.0, 10.0.2.0, and 10.0.3.0 networks,
and only those four networks.

QUESTION 16
Which set of commands is recommended to prevent the use of a hub in the access layer?

A. switch(config-if)#switchport mode trunk

switch(config-if)#switchport port-security maximum 1
B. switch(config-if)#switchport mode trunk
switch(config-if)#switchport port-security mac-address 1
C. switch(config-if)#switchport mode access
switch(config-if)#switchport port-security maximum 1
D. switch(config-if)#switchport mode access
switch(config-if)#switchport port-security mac-address 1

Correct Answer: C
Section: (none)
Explanation

Explanation/Reference:

QUESTION 17
A router has learned three possible routes that could be used to reach a destination network. One
route is from EIGRP and has a composite metric of 20514560. Another route is from OSPF with a
metric of 782. The last is from RIPv2 and has a metric of 4. Which route or routes will the router
install in the routing table?

A. the OSPF route

B. the EIGRP route
C. the RIPv2 route
D. all three routes
E. the OSPF and RIPv2 routes

Correct Answer: B
Section: (none)
Explanation

Explanation/Reference:

QUESTION 18
Two routers named Atlanta and Brevard are connected via their serial interfaces as illustrated,
but they are unable to communicate. The Atlanta router is known to have the correct
configuration.

Given the partial configurations, identify the fault on the Brevard router that is causing the lack of
connectivity

A. incompatible IP address
B. insufficient bandwidth
C. incorrect subnet mask
D. incompatible encapsulation
E. link reliability too low
F. IPCP closed

Correct Answer: D
Section: (none)
Explanation

Explanation/Reference:

QUESTION 19
A network administrator needs to configure a serial link between the main office and a remote
location. The router at the remote office is a non-Cisco router. How should the network
administrator configure the serial interface of the main office router to make the connection?

A. Main(config)# interface serial 0/0

Main(config-if)# ip address 172.16.1.1 255.255.255.252
Main(config-if)# no shut
B. Main(config)# interface serial 0/0
Main(config-if)# ip address 172.16.1.1 255.255.255.252
Main(config-if)# encapsulation ppp
Main(config-if)# no shut
C. Main(config)# interface serial 0/0
Main(config-if)# ip address 172.16.1.1 255.255.255.252
Main(config-if)# encapsulation frame-relay
 Main(config-if)# authentication chap
Main(config-if)# no shut
D. Main(config)# interface serial 0/0
Main(config-if)#ip address 172.16.1.1 255.255.255.252
Main(config-if)#encapsulation ietf
Main(config-if)# no shut

Correct Answer: B
Section: (none)
Explanation

Explanation/Reference:

QUESTION 20
Which Layer 2 protocol encapsulation type supports synchronous and asynchronous circuits and
has built-in security mechanisms?

A. HDLC
B. PPP
C. X.25
D. Frame Relay

Correct Answer: B
Section: (none)
Explanation

Explanation/Reference:

QUESTION 21
Refer to the exhibit. The two connected ports on the switch are not turning orange or green. What
would be the most effective steps to troubleshoot this physical layer problem? (Choose three.)

A. Ensure that the Ethernet encapsulations match on the interconnected router and switch ports.
B. Ensure that cables A and B are straight-through cables.
C. Ensure cable A is plugged into a trunk port.
D. Ensure the switch has power.
E. Reboot all of the devices.
F. Reseat all cables.

Correct Answer: BDF

Section: (none)
Explanation

Explanation/Reference:

QUESTION 22
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The
routers cannot establish an adjacency relationship on their common Ethernet link.

The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2.
Based on the information in the graphic, what is the cause of this problem?

A. The OSPF area is not configured properly.

B. The priority on R1 should be set higher.
C. The cost on R1 should be set higher.
D. The hello and dead timers are not configured properly.
E. A backup designated router needs to be added to the network.
F. The OSPF process ID numbers must match.

Correct Answer: D
Section: (none)
Explanation

Explanation/Reference:

QUESTION 23
What will happen if a private IP address is assigned to a public interface connected to an ISP?

A. Addresses in a private range will be not be routed on the Internet backbone.

B. Only the ISP router will have the capability to access the public network.
C. The NAT process will be used to translate this address to a valid IP address.
D. A conflict of IP addresses happens, because other public routers can use the same range.
Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:

QUESTION 24
Refer to the exhibit. The Bigtime router is unable to authenticate to the Littletime router. What is
the cause of the problem?

A. The usernames are incorrectly configured on the two routers.

B. The passwords do not match on the two routers.
C. CHAP authentication cannot be used on a serial interface.
D. The routers cannot be connected from interface S0/0 to interface S0/0.
E. With CHAP authentication, one router must authenticate to another router. The routers cannot be
configured to authenticate to each other.

Correct Answer: B
Section: (none)
Explanation

Explanation/Reference:

QUESTION 25
What will be the result if the following configuration commands are implemented on a Cisco
switch?

Switch(config-if)# switchport port-security

Switch(config-if)# switchport port-security mac-address sticky

A. A dynamically learned MAC address is saved in the startup-configuration file.

B. A dynamically learned MAC address is saved in the running-configuration file.
C. A dynamically learned MAC address is saved in the VLAN database.
D. Statically configured MAC addresses are saved in the startup-configuration file if frames from that
address are received.
E. Statically configured MAC addresses are saved in the running-configuration file if frames from that
address are received.

Correct Answer: B
Section: (none)
Explanation

Explanation/Reference:
QUESTION 26
Refer to the exhibit. The following commands are executed on interface fa0/1 of 2950Switch.

2950Switch(config-if)# switchport port-security

2950Switch(config-if)# switchport port-security mac-address sticky
2950Switch(config-if)# switchport port-security maximum 1

The Ethernet frame that is shown arrives on interface fa0/1.

What two functions will occur when this frame is received by 2950Switch? (Choose two.)

A. The MAC address table will now have an additional entry of fa0/1 FFFF.FFFF.FFFF.
B. Only host A will be allowed to transmit frames on fa0/1.
C. This frame will be discarded when it is received by 2950Switch.
D. All frames arriving on 2950Switch with a destination of 0000.00aa.aaaa will be forwarded out fa0/1.
E. Hosts B and C may forward frames out fa0/1 but frames arriving from other switches will not be forwarded
out fa0/1.
F. Only frames from source 0000.00bb.bbbb, the first learned MAC address of 2950Switch, will be forwarded
out fa0/1.

Correct Answer: BD
Section: (none)
Explanation

Explanation/Reference:

QUESTION 27
Which command would you configure globally on a Cisco router that would allow you to view
directly connected Cisco devices?

A. enable cdp
B. cdp enable
C. cdp run
D. run cdp
Correct Answer: C
Section: (none)
Explanation

Explanation/Reference:

QUESTION 28
A Cisco router is booting and has just completed the POST process. It is now ready to find and
load an IOS image. What function does the router perform next?

A. It checks the configuration register.

B. It attempts to boot from a TFTP server.
C. It loads the first image file in flash memory.
D. It inspects the configuration file in NVRAM for boot instructions.

Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:

QUESTION 29
What are three advantages of VLANs? (Choose three.)

A. VLANs establish broadcast domains in switched networks.

B. VLANs utilize packet filtering to enhance network security.
C. VLANs provide a method of conserving IP addresses in large networks.
D. VLANs provide a low-latency internetworking alternative to routed networks.
E. VLANs allow access to network services based on department, not physical location.
F. VLANs can greatly simplify adding, moving, or changing hosts on the network.

Correct Answer: AEF

Section: (none)
Explanation

Explanation/Reference:

QUESTION 30
Refer to the exhibit. The output that is shown is generated at a switch. Which three statements
are true? (Choose three.)
A. All ports will be in a state of discarding, learning, or forwarding.
B. Thirty VLANs have been configured on this switch.
C. The bridge priority is lower than the default value for spanning tree.
D. All interfaces that are shown are on shared media.
E. All designated ports are in a forwarding state.
F. This switch must be the root bridge for all VLANs on this switch.

Correct Answer: ACE

Section: (none)
Explanation

Explanation/Reference:

QUESTION 31
Which two commands can be used to verify a trunk link configuration status on a given Cisco
switch interface? (Choose two.)

A. show interface trunk

B. show interface interface
C. show ip interface brief
D. show interface vlan
E. show interface switchport

Correct Answer: AE
Section: (none)
Explanation

Explanation/Reference:

QUESTION 32
Which two states are the port states when RSTP has converged? (Choose two.)

A. discarding
B. listening
C. learning
D. forwarding
E. disabled

Correct Answer: AD
Section: (none)
Explanation

Explanation/Reference:

QUESTION 33
Refer to the exhibit. A technician has installed SwitchB and needs to configure it for remote
access from the management workstation connected to SwitchA . Which set of commands is
required to accomplish this task?

A. SwitchB(config)# interface FastEthernet 0/1

SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# no shutdown
B. SwitchB(config)# interface vlan 1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# ip default-gateway 192.168.8.254 255.255.255.0
SwitchB(config-if)# no shutdown
C. SwitchB(config)# ip default-gateway 192.168.8.254
SwitchB(config)# interface vlan 1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# no shutdown
D. SwitchB(config)# ip default-network 192.168.8.254
SwitchB(config)# interface vlan 1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# no shutdown
E. SwitchB(config)# ip route 192.168.8.254 255.255.255.0
SwitchB(config)# interface FastEthernet 0/1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# no shutdown

Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:

QUESTION 34
Which of the following are benefits of VLANs? (Choose three.)

A. They increase the size of collision domains.

B. They allow logical grouping of users by function.
C. They can enhance network security.
D. They increase the size of broadcast domains while decreasing the number of collision domains.
E. They increase the number of broadcast domains while decreasing the size of the broadcast domains.
F. They simplify switch administration.

Correct Answer: BCE

Section: (none)
Explanation

Explanation/Reference:

QUESTION 35
What are three benefits of implementing VLANs? (Choose three.)

A. A higher level of network security can be reached by separating sensitive data traffic from other
network traffic.
B. A more efficient use of bandwidth can be achieved allowing many physical groups to use the same
network infrastructure.
C. A more efficient use of bandwidth can be achieved allowing many logical networks to use the same
network infrastructure.
D. Broadcast storms can be mitigated by increasing the number of broadcast domains, thus reducing
their size.
E. Broadcast storms can be mitigated by decreasing the number of broadcast domains, thus increasing
their size.
F. VLANs make it easier for IT staff to configure new logical groups, because the VLANs all belong to
the same broadcast domain.
G. Port-based VLANs increase switch-port use efficiency, thanks to 802.1Q trunks.

Correct Answer: ACD

Section: (none)
Explanation

Explanation/Reference:

QUESTION 36
Which three statements accurately describe Layer 2 Ethernet switches? (Choose three.)

A. Spanning Tree Protocol allows switches to automatically share VLAN information.

B. Establishing VLANs increases the number of broadcast domains.
C. Switches that are configured with VLANs make forwarding decisions based on both Layer 2 and
Layer 3 address information.
D. Microsegmentation decreases the number of collisions on the network.
E. In a properly functioning network with redundant switched paths, each switched segment will contain
one root bridge with all its ports in the forwarding state. All other switches in that broadcast domain will
have only one root port.
F. If a switch receives a frame for an unknown destination, it uses ARP to resolve the address.

Correct Answer: BDE

Section: (none)
Explanation

Explanation/Reference:

QUESTION 37
Which of the following correctly describe steps in the OSI data encapsulation process? (Choose two.)

A. The transport layer divides a data stream into segments and may add reliability and flow control information.
B. The data link layer adds physical source and destination addresses and an FCS to the segment.
C. Packets are created when the network layer encapsulates a frame with source and destination host
addresses and protocol-related control information.
D. Packets are created when the network layer adds Layer 3 addresses and control information to a segment.
E. The presentation layer translates bits into voltages for transmission across the physical link.

Correct Answer: AD
Section: (none)
Explanation

Explanation/Reference:

QUESTION 38
Which of the following describes the roles of devices in a WAN? (Choose three.)

A. A CSU/DSU terminates a digital local loop.

B. A modem terminates a digital local loop.
C. A CSU/DSU terminates an analog local loop.
D. A modem terminates an analog local loop.
E. A router is commonly considered a DTE device.
F. A router is commonly considered a DCE device.

Correct Answer: ADE

Section: (none)
Explanation

Explanation/Reference:

QUESTION 39
Which interface counter can you use to diagnose a duplex mismatch problem?

A. no carrier
B. late collisions
C. giants
D. CRC errors
E. deferred
F. runts

Correct Answer: B
Section: (none)
Explanation

Explanation/Reference:

QUESTION 40
Which feature can you implement to reserve bandwidth for VoIP calls across the call path?

A. PQ
B. CBWFQ
C. round robin
D. RSVP

Correct Answer: D
Section: (none)
Explanation

Explanation/Reference:

QUESTION 41
When an interface is configured with PortFast BPDU guard, how does the interface respond when it receives a
BPDU?

A. It continues operating normally.

B. It goes into a down/down state.
C. It becomes the root bridge for the configured VLAN.
D. It goes into an errdisable state.

Correct Answer: D
Section: (none)
Explanation

Explanation/Reference:

QUESTION 42
What are three characteristics of the TCP protocol? (Choose three.)

A. It uses a single SYN-ACK message to establish a connection.

B. The connection is established before data is transmitted.
C. It ensures that all data is transmitted and received by the remote device.
D. It supports significantly higher transmission speeds than UDP.
E. It requires applications to determine when data packets must be retransmitted.
F. It uses separate SYN and ACK messages to establish a connection.

Correct Answer: BCF

Section: (none)
Explanation

Explanation/Reference:

QUESTION 43
Which command can you enter to determine whether serial interface 0/2/0 has been configured using HDLC
encapsulation?

A. router#show platform
B. router#show interfaces Serial 0/2/0
C. router#show ip interface s0/2/0
D. router#show ip interface brief

Correct Answer: B
Section: (none)
Explanation

Explanation/Reference:

QUESTION 44
Which two statements about IPv4 multicast traffic are true? (Choose two.)

A. It burdens the source host without affecting remote hosts.

B. It uses a minimum amount of network bandwidth.
C. It is bandwidth-intensive.
D. It simultaneously delivers multiple streams of data.
E. It is the most efficient way to deliver data to multiple receivers.

Correct Answer: DE
Section: (none)
Explanation

Explanation/Reference:

QUESTION 45
What are two benefits of private IPv4 IP addresses? (Choose two.)

A. They are routed the same as public IP addresses.

B. They are less costly than public IP addresses.
C. They can be assigned to devices without Internet connections.
D. They eliminate the necessity for NAT policies.
E. They eliminate duplicate IP conflicts.

Correct Answer: BC
Section: (none)
Explanation

Explanation/Reference:

QUESTION 46
What is the authoritative source for an address lookup?

A. a recursive DNS search

B. the operating system cache
C. the ISP local cache
D. the browser cache
Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:

QUESTION 47
Which command can you enter to verify that a BGP connection to a remote device is established?

A. show ip bgp summary

B. show ip community-list
C. show ip bgp paths
D. show ip route

Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:

QUESTION 48
During which phase of PPPoE is PPP authentication performed?

A. the PPP Session phase

B. Phase 2
C. the Active Discovery phase
D. the Authentication phase
E. Phase 1

Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:

QUESTION 49
Which three circumstances can cause a GRE tunnel to be in an up/down state? (Choose three.)

A. The tunnel interface IP address is misconfigured.

B. The tunnel interface is down.
C. A valid route to the destination address is missing from the routing table.
D. The tunnel address is routed through the tunnel itself.
E. The ISP is blocking the traffic.
F. An ACL is blocking the outbound traffic.

Correct Answer: BCD

Section: (none)
Explanation

Explanation/Reference:
QUESTION 50
Which two statements about using leased lines for your WAN infrastructure are true? (Choose two.)

A. Leased lines provide inexpensive WAN access.

B. Leased lines with sufficient bandwidth can avoid latency between endpoints.
C. Leased lines require little installation and maintenance expertise.
D. Leased lines provide highly flexible bandwidth scaling.
E. Multiple leased lines can share a router interface.
F. Leased lines support up to T1 link speeds.

Correct Answer: CD
Section: (none)
Explanation

Explanation/Reference:

QUESTION 51
Which two statements about wireless LAN controllers are true? (Choose two.)

A. They can simplify the management and deployment of wireless LANs.

B. They rely on external firewalls for WLAN security.
C. They are best suited to smaller wireless networks.
D. They must be configured through a GUI over HTTP or HTTPS.
E. They can manage mobility policies at a systemwide level.

Correct Answer: AE
Section: (none)
Explanation

Explanation/Reference:

QUESTION 52
Which two statements about northbound and southbound APIs are true? (Choose two.)

A. Only southbound APIs allow program control of the network.

B. Only northbound APIs allow program control of the network.
C. Only southbound API interfaces use a Service Abstraction Layer.
D. Only northbound API interfaces use a Service Abstraction Layer.
E. Both northbound and southbound API interfaces use a Service Abstraction Layer.
F. Both northbound and southbound APIs allow program control of the network.

Correct Answer: BC
Section: (none)
Explanation

Explanation/Reference:

QUESTION 53
Which command can you enter to set the default route for all traffic to an interface?
A. router(config)#ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/1
B. router(config-router)#default-information originate always
C. router(config)#ip route 0.0.0.0 255.255.255.255 GigabitEthernet0/1
D. route(config-router)#default-information originate

Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:

QUESTION 54

A.
Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:
The REAL DnD is said to be something like this but different here is the actual one (No illustration):

FF01::1 All nodes (node-local)

FF01::2 All routers (node-local)
FF02::1 All nodes (link-local)
FF02::2 All routers (link-local)
FF02::5 OSPFv3 routers
FF02::6 OSPFv3 designated routers
FF02::9 Routing Information Protocol (RIPng)
FF02::A EIGRP routers
FF02::B Mobile agents
FF02::C SSDP
FF02::D All PIM routers
FF05::2 All routers (site-local)
Extra Choice DHCP servers/relay agents (FF05::1:3)

QUESTION 55
Which WAN topology is most appropriate for a centrally located server farm with several satellite branches?

A. star
B. hub and spoke
C. point-to-point
D. full mesh

Correct Answer: B
Section: (none)
Explanation

Explanation/Reference:
In a Hub-and-spoke Site-to-Site Wide Area Network (WAN) network topology, one physical site act as Hub
(Example, Main Office), while other physical sites act as spokes. Spoke sites are connected to each other via
Hub site. In Huband-spoke
Wide Area Network (WAN) topology, the network communication between two spokes always travels through
the hub.

QUESTION 56
Which function allows EIGRP peers to receive notice of implementing topology changes?

A. successors
B. advertised changes
C. goodbye messages
D. expiration of the hold timer

Correct Answer: C
Section: (none)
Explanation

Explanation/Reference:

QUESTION 57
If you configure syslog messages without specifying the logging trap level, which log messages will the router
send?

A. informational messages only

B. warning and error conditions only
C. normal but significant conditions only
D. error conditions only
E. all levels except debugging

Correct Answer: E
Section: (none)
Explanation

Explanation/Reference:

QUESTION 58
Which three options are benefits of using TACACS+ on a device? (Choose three)

A. It ensures that user activity is untraceable.

B. It provides a secure accounting facility on the device.
C. device-administration packets are encrypted in their entirely.
D. It allows the user to remotely access devices from other vendors.
E. It allows the users to be authenticated against a remote server.
F. It supports access-level authorization for commands.

Correct Answer: CEF

Section: (none)
Explanation

Explanation/Reference:
http://tacacs.net/docs/TACACS_Advantages.pdf
http://www.cisco.com/c/en/us/support/docs/security-vpn/remote-authentication-dial-user-serviceradius/13838-
10.html

QUESTION 59
What layer of the OSI Model is included in TCP/IP Model's INTERNET layer?

A. Application
B. Session
C. Data Link
D. Presentation
E. Network

Correct Answer: E
Section: (none)
Explanation

Explanation/Reference:
NOT SURE ABOUT THE CHOICES. NOT SURE ABOUT THE QUESTION EITHER.

QUESTION 60
Which two of these are characteristics of the 802.1Q protocol? (Choose two.)

A. It is used exclusively for tagging VLAN frames and does not address network reconvergence following
switched network topology changes.
B. It modifies the 802.3 frame header, and thus requires that the FCS be recomputed.
C. It is a Layer 2 messaging protocol which maintains VLAN configurations across networks.
D. It includes an 8-bit field which specifies the priority of a frame.
E. It is a trunking protocol capable of carrying untagged frames.

Correct Answer: BE
Section: (none)
Explanation

Explanation/Reference:

QUESTION 61
Which two features can dynamically assign IPv6 addresses? (Choose two.)

A. IPv6 stateless autoconfiguration

B. DHCP
C. NHRP
D. IPv6 stateful autoconfiguration
E. ISATAP tunneling

Correct Answer: AB
Section: (none)
Explanation

Explanation/Reference:

QUESTION 62
A security administrator wants to profile endpoints and gain visibility into attempted authentications. Which
802.1x mode allows these actions?

A. Monitor mode
B. High-Security mode
C. Low-impact mode
D. Closed mode

Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:

QUESTION 63
How to verify SSH connections was secured?

A. ssh -v 1 -l admin IP
B. ssh -v 2 -l admin IP
C. ssh -l admin IP
D. ANOTHER OPTION (WRONG)

Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
Sorry for the question but they said it was something like that.

QUESTION 64
Which statement about RADIUS security is true?

A. It supports EAP authentication for connecting to wireless networks.

B. It provides encrypted multiprotocol support.
C. Device-administration packets are encrypted in their entirety.
D. It ensures that user activity is fully anonymous.

Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:

QUESTION 65
Three correct things about IPv6 unique local addresses (Choose three.)

A. Refer to Explanation/Reference

Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:
No information abot the actual question and choices: but this might help you.

Local IPv6 unicast addresses have the following characteristics:

- Globally unique prefix (with high probability of uniqueness).

- Well-known prefix to allow for easy filtering at site

boundaries.

- Allow sites to be combined or privately interconnected without

creating any address conflicts or requiring renumbering of
interfaces that use these prefixes.

- Internet Service Provider independent and can be used for

communications inside of a site without having any permanent or
intermittent Internet connectivity.

- If accidentally leaked outside of a site via routing or DNS,

there is no conflict with any other addresses.

- In practice, applications may treat these addresses like global

scoped addresses.

This approach has the following advantages:

- Provides Local IPv6 prefixes that can be used independently of

any provider-based IPv6 unicast address allocations. This is
useful for sites not always connected to the Internet or sites
that wish to have a distinct prefix that can be used to localize
 traffic inside of the site.

- Applications can treat these addresses in an identical manner as

any other type of global IPv6 unicast addresses.

- Sites can be merged without any renumbering of the Local IPv6

addresses.

- Sites can change their provider-based IPv6 unicast address

without disrupting any communication that uses Local IPv6
addresses.

- Well-known prefix that allows for easy filtering at site

boundary.

- Can be used for inter-site VPNs.

- If accidently leaked outside of a site via routing or DNS, there

is no conflict with any other addresses.

This approach has the following disadvantages:

- Not possible to route Local IPv6 prefixes on the global Internet

with current routing technology. Consequentially, it is
necessary to have the default behavior of site border routers to
filter these addresses.

- There is a very low probability of non-unique locally assigned

Global IDs being generated by the algorithm in Section 3.2.3.
This risk can be ignored for all practical purposes, but it
leads to a theoretical risk of clashing address prefixes.

QUESTION 66
If you are configuring syslog messages specifying logging trap warning, which log messages will the router
send?

A. 0-4
B. 0-5
C. 0-2
D. 0-6
E. 0-1

Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:
0 emergencies System is unusable
1 alerts Immediate action is needed
2 critical Critical conditions exist
3 errors Error conditions exist
4 warnings Warning conditions exist
5 notification Normal, but significant, conditions exist
6 informational Informational messages
7 debugging Debugging messages

QUESTION 67
What is the correct command for floating static ipv6 route?
A. ipv6 route 2001:DB8::/32 serial 2/0 201
B. ipv6 route 2001:DB8::/32 serial 2/0 1
C. N/A
D. N/A

Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:

QUESTION 68
What is true about Ethernet? (Choose Two.)

A. 802.2 Protocol
B. 802.3 Protocol
C. 10BaseT half duplex
D. CSMA/CD Stops transmitting when congestion occurs
E. CSMA/CA Stops transmitting when congestion occurs

Correct Answer: BD
Section: (none)
Explanation

Explanation/Reference:
http://www.ieee802.org/3/
CSMA/CD - It uses a carrier sensing scheme in which a transmitting station detects collisions by sensing
transmissions from other stations while transmitting a frame. When this collision condition is detected, the
station stops transmitting that frame.

QUESTION 69
What IP SLA ICMP Echo measures?

A. Packet loss
B. Congestion
C. Hop-by-hop something
D. -ANOTHER OPTION-
E. -ANOTHER OPTION-

Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:
There is no RRT (Round-trip time) in the choices @Mik said.

QUESTION 70
What are types of IPv6 static routes? (Choose Three.)

A. Recursive routes
B. Directly connected routes
C. Fully specified routes
D. -ANOTHER OPTION-
E. -ANOTHER OPTION-
F. -ANOTHER OPTION-

Correct Answer: ABC

Section: (none)
Explanation

Explanation/Reference:
http://ipcisco.com/ipv6-static-routes-for-cisco-routers/
http://www.orbit-computer-solutions.com/ipv6-static-and-default-route-how-to-configure-ipv6-static-and-default-
route/

QUESTION 71
How to configure RIPv2? (Choose Two.)

A. Enable RIP
B. Connect RIP to WAN interface
C. Enable auto-summary
D. Enable authentication
E. -ANOTHER OPTION-

Correct Answer: AC
Section: (none)
Explanation

Explanation/Reference:
C because we can enable or disable auto-summary in rips.

QUESTION 72
What is the status of port-channel if LACP is misconfigured?

A. Forwarding
B. Enabled
C. Disabled
D. Errdisabled

Correct Answer: C
Section: (none)
Explanation

Explanation/Reference:

QUESTION 73
What is true about DTP? (Choose Three.)

A. Layer 2 protocol
B. Layer 3 protocol
C. Proprietary protocol
D. enabled by default
E. disabled by default

Correct Answer: ACD

Section: (none)
Explanation
Explanation/Reference:
https://en.wikipedia.org/wiki/Dynamic_Trunking_Protocol

QUESTION 74
How to create a trunk port and allow VLAN 20? (Choose Three.)

A. switchport trunk encapsulation dot1q

B. switchport mode trunk
C. switchport trunk allowed vlan 20
D. switchport trunk native vlan 20
E. -ANOTHER OPTION-

Correct Answer: ABC

Section: (none)
Explanation

Explanation/Reference:

QUESTION 75
What 8-bit field exists in IP packet for QoS?

A. Tos Field
B. DSCP
C. IP Precedence
D. Cos
E. -ANOTHER OPTION-

Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:
http://flylib.com/books/2/686/1/html/2/images/1587051990/graphics/13fig01.gif

QUESTION 76
What feature uses a random time to re-sent a frame?

A. CSMA/CA
B. -ANOTHER OPTION-
C. -ANOTHER OPTION-
D. CSMA/CD

Correct Answer: D
Section: (none)
Explanation

Explanation/Reference:

QUESTION 77
Which mode is compatible with Trunk, Access, and desirable ports?

A. Trunk Ports
B. Access Ports
C. Dynamic Auto
D. Dynamic Desirable

Correct Answer: C
Section: (none)
Explanation

Explanation/Reference:
The 'dynamic auto' will configure the port to accept incoming negotiation and will accept becoming
either a trunk or an access port. Dynamic Auto allows the port to negotiate DTP (Dynamic Trunking Protocol) if
the
other side is set to trunk or desirable. Otherwise it will become an access port.

QUESTION 78
If you configure syslog messages without specifying the logging trap level, which log messages will the router
send?

A. 0-4
B. 0-5
C. 0-2
D. 0-6
E. 0-1

Correct Answer: D
Section: (none)
Explanation

Explanation/Reference:
Router(config)# logging trap level - Specifies the kind of messages, by severity level, to be sent to the
syslog server. The default is informational (6) and lower ( 0 6). The possible values for level are as follows:
Emergency: 0
Alert: 1
Critical: 2
Error: 3
Warning: 4
Notice: 5
Informational: 6
Debug: 7

QUESTION 79
Which command can you execute to set the user inactivity timer to 10 seconds?

A. SW1(config-line)#exec-timeout 0 10
B. SW1(config-line)#exec-timeout 10
C. SW1(config-line)#absolute-timeout 0 10
D. SW1(config-line)#absolute-timeout 10

Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:

QUESTION 80
Which standards-based First Hop Redundancy Protocol is a Cisco supported alternative to
Hot Standby Router Protocol?

A. VRRP
B. GLBP
C. TFTP
D. DHCP

Correct Answer: A
Section: (none)
Explanation

Explanation/Reference:

QUESTION 81
Two hosts are attached to a switch with the default configuration. Which statement about the
configuration is true?

A. IP routing must be enabled to allow the two hosts to communicate.

B. The two hosts are in the same broadcast domain.
C. The switch must be configured with a VLAN to allow the two hosts to communicate.
D. Port security prevents the hosts from connecting to the switch.

Correct Answer: B
Section: (none)
Explanation

Explanation/Reference:

QUESTION 82
If a router has 3 hosts connected in one port and two other hosts connected in another port, how may
broadcast domains are present on the router?

A. 5
B. 2
C. 3
D. 4

Correct Answer: B
Section: (none)
Explanation

Explanation/Reference:
ROAS

QUESTION 83
If a router has four interfaces and each interface is connected to four switches, how many
broadcast domains are present on the router?

A. 1
B. 2
C. 4
D. 8
Correct Answer: C
Section: (none)
Explanation

Explanation/Reference:

QUESTION 84
What are three parts of an IPv6 global unicast address? (Choose three.)

A. an interface ID that is used to identify the local host on the network.

B. an interface ID that is used to identify the local network for a particular host.
C. a subnet ID that is used to identify networks inside of the local enterprise site
D. a global routing prefix that is used to identify the network portion of the address that has been provided by
an ISP
E. a global routing prefix that is used to identify the portion of the network address provided by a local
administrator

Correct Answer: ACD

Section: (none)
Explanation

Explanation/Reference:

QUESTION 85
You have been asked to come up with a subnet mask that will allow all three web servers to be
on the same network while providing the maximum number of subnets. Which network address
and subnet mask meet this requirement?

A. 192.168.252.0 255.255.255.252
B. 192.168.252.8 255.255.255.248
C. 192.168.252.8 255.255.255.252
D. 192.168.252.16 255.255.255.240
E. 192.168.252.16 255.255.255.252

Correct Answer: B
Section: (none)
Explanation

Explanation/Reference:

QUESTION 86
What parameter can be different on ports within an EtherChannel?

A. speed
B. DTP negotiation settings
C. trunk encapsulation
D. duplex

Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:

QUESTION 87
Which two statements about IPv6 router advertisement messages are true? (Choose two.)

A. They use ICMPv6 type 134.

B. The advertised prefix length must be 64 bits.
C. The advertised prefix length must be 48 bits.
D. They are sourced from the configured IPv6 interface address.
E. Their destination is always the link-local address of the neighboring node.

Correct Answer: AB
Section: (none)
Explanation

Explanation/Reference:

QUESTION 88
Which spanning-tree protocol rides on top of another spanning-tree protocol?

A. MSTP
B. RSTP
C. PVST+
D. Mono Spanning Tree

Correct Answer: A
Section: (none)
Explanation

Explanation/Reference: