Technical Guide

High Capacity Forklift Truck

 H550-700HD/S DIMENSIONS

4-21

4-35

4-1
4-1 4-1
4-1

4-5
4-5

4-2
4-4
4-4

4-7
1-6

1-5
1-5

4-31
4-31
4-32
4-32

1-8
1-8 1-9
4-20
4-20

4-19
4-19

2
 H550-700HDS SPECIFICATIONS

Description Units English Metric English Metric English Metric

1-1 Manufacturer HYSTER HYSTER HYSTER HYSTER HYSTER HYSTER
1-2 Model designation H550HDS H550HDS H650HDS H650HDS H700HDS H700HDS
GENERAL

1-5 Rated load capacity lbs kg 55,000 24,948 65,000 29,483 70,000 31,751
1-6 Load center in mm 36 914 36 914 36 914
1-8 Load distance in mm 44 1115 45 1150 45 1150
1-9 Wheelbase in mm 144 3655 155 3935 155 3935
2-1 Total truck weight without load lbs kg 80,658 36,586 96,450 43,749 97,795 44,359
2-2a Axle loading with load front lbs kg 124,993 56,696 147,430 66,873 155,122 70,362
WEIGHTS

2-2b rear lbs kg 10,666 4838 14,019 6359 12,674 5749

2-3a Axle loading without load front lbs kg 39,608 17,966 48,319 21,917 48,425 21,965
2-3b rear lbs kg 41,052 18,621 48,131 21,832 49,370 22,394
3-1 Tire type Pneumatic Pneumatic Pneumatic
WHEELS

3-2 Tire size front 14.00 x 24-28PR 16.00 x 25-32PR 16.00 x 25-32PR
3-3 rear 14.00 x 24-28PR 16.00 x 25-32PR 16.00 x 25-32PR
4-1 Mast tilt, forward / back degrees 6 / 10 6 / 10 6 / 10
4-2 Height of mast lowered in mm 139 3491 143 3616 143 3616
4-3 Freelift (Top of Fork) w/o LBR in mm 0 0 0 0 0 0
4-4 Lift height (Top of Fork) in mm 124 3155 124 3155 124 3155
4-5 Height of mast extended in mm 199 5016 203 5141 203 5141
4-7 Height to top of operator compartment in mm 132 3356 136 3452 136 3452
4-19 Overall length in mm 325 8247 337 8562 337 8562
4-20 Length to load face in mm 229 5807 241 6122 241 6122
4-21 Overall width over drive tires in mm 127 3220 135 3430 135 3430
DIMENSIONS

4-22a Fork thickness in mm 4.13 105 4.33 110 4.33 110

4-22b width in mm 11.0 280 11.8 300 11.8 300
4-22c length in mm 96 2440 96 2440 96 2440
4-24 Carriage width in mm 123 3120 130 3300 130 3300
4-25a Fork spread, min (in-in) in mm 9 235 9 235 9 235
4-25b Fork spread, max (out-out) in mm 94 2375 94 2375 94 2375
4-31 Ground clearance, under mast with load in mm 9 219 9 227 9 227
4-32 Ground clearance, center of wheelbase in mm 16 406 20 502 20 502
4-33 Minimum aisle width (add load length) in mm 358 9098 376 9538 376 9538
4-35 Outside turning radius in mm 210 5326 224 5691 224 5691
8-7 Hydraulic tank capacity gal L 75 286 86 326 86 326
8-8 Fuel tank capacity gal L 80 304 96 364 96 364
PERFORMANCE TIER 4 FINAL CUMMINS QSB 6.7L ENGINE
PERFORMANCE (TIER 4 FINAL)

5-1a Travel speed with load mph km/h 16 25 16 25 16 25

5-1b without load mph km/h 16 25 16 25 16 25
5-2a Lifting speed with load ft/min m/s 67 0.34 53 0.27 53 0.27
5-2b without load ft/min m/s 69 0.35 57 0.29 57 0.29
5-3a Lowering speed with load ft/min m/s 98 0.50 98 0.50 98 0.50
5-3b without load ft/min m/s 98 0.50 98 0.50 98 0.50
5-6 Drawbar Pull - Max lbs kN 54,400 242 55,100 245 55,100 245
5-7 Gradeability no load / rated load - 1 mph (1.6 km/h) % 34 / 42 35 / 35 34 / 33
PERFORMANCE TIER 3 CUMMINS QSB 6.7L ENGINE
5-1a Travel speed with load mph km/h 16 25 16 25 16 25
PERFORMANCE (TIER 3)

5-1b without load mph km/h 16 25 16 25 16 25

5-2a Lifting speed with load ft/min m/s 65 0.33 53 0.27 53 0.27
5-2b without load ft/min m/s 69 0.35 57 0.29 57 0.29
5-3a Lowering speed with load ft/min m/s 98 0.50 98 0.50 98 0.50
5-3b without load ft/min m/s 98 0.50 98 0.50 98 0.50
5-6 Drawbar Pull - Max lbs kN 54,600 243 55,100 245 55,100 245
5-7 Gradeability no load / rated load - 1 mph (1.6 km/h) % 34 / 43 35 / 35 34 / 33

CERTIFICATION: These Hyster lift trucks meet design specifications of Part II ANSI B56.1-1969, as required by OSHA Section 1910.178(a)(2) and also comply with Part III ANSI B56.1-
revision in effect at time of manufacture. Certification of compliance with the applicable ANSI standards appears on the lift truck. Performance specifications are for a truck equipped
as described under Standard Equipment on this Technical Guide. Performance specifications are affected by the condition of the vehicle and how it is equipped, as well as by the nature,
condition of the operating area, proper service and maintenance of the vehicle. If these specifications are critical, the proposed application should be discussed with your dealer.

3
 H550-700HD SPECIFICATIONS

Description Units English Metric English Metric English Metric English Metric
1-1 Manufacturer HYSTER HYSTER HYSTER HYSTER HYSTER HYSTER HYSTER HYSTER
1-2 Model designation H550HD H550HD H620HD H620HD H650HD H650HD H700HD H700HD
GENERAL

1-5 Rated load capacity lbs kg 55,000 24,948 62,000 28,123 65,000 29,483 70,000 31,751
1-6 Load center in mm 48 1220 48 1220 48 1220 48 1220
1-8 Load distance in mm 44 1115 45 1145 45 1150 45 1150
1-9 Wheelbase in mm 170 4315 170 4315 170 4315 190 4825
2-1 Total truck weight without load lbs kg 81,589 37,008 96,999 43,998 98,531 44,693 97,508 44,229
2-2a Axle loading with load front lbs kg 124,425 56,438 143,905 65,274 149,544 67,832 152,750 69,286
WEIGHTS

2-2b rear lbs kg 12,165 5518 15,095 6847 13,988 6345 14,760 6695
2-3a Axle loading without load front lbs kg 39,855 18,078 48,356 21,934 48,524 22,010 48,389 21,949
2-3b rear lbs kg 41,734 18,930 48,643 22,064 50,007 22,683 49,119 22,280
3-1 Tire type Pneumatic Pneumatic Pneumatic Pneumatic
WHEELS

3-2 Tire size front 14.00 x 24-28PR 16.00 x 25-32PR 16.00 x 25-32PR 16.00 x 25-32PR
3-3 rear 14.00 x 24-28PR 16.00 x 25-32PR 16.00 x 25-32PR 16.00 x 25-32PR
4-1 Mast tilt, forward / back degrees 6 / 10 6 / 10 6 / 10 6 / 10
4-2 Height of mast lowered in mm 139 3491 143 3616 143 3616 143 3616
4-3 Freelift (Top of Fork) w/o LBR in mm 0 0 0 0 0 0 0 0
4-4 Lift height (Top of Fork) in mm 124 3155 124 3155 124 3155 124 3155
4-5 Height of mast extended in mm 199 5016 203 5141 203 5141 203 5141
4-7 Height to top of operator compartment in mm 132 3356 136 3452 136 3452 136 3452
4-19 Overall length in mm 351 8907 352 8937 352 8942 372 9452
4-20 Length to load face in mm 255 6467 256 6497 256 6502 276 7012
4-21 Overall width over drive tires in mm 127 3220 135 3430 135 3430 135 3430
DIMENSIONS

4-22a Fork thickness in mm 4.13 105 4.33 105 4.33 110 4.33 110
4-22b width in mm 11.0 280 11.8 300 11.8 300 11.8 300
4-22c length in mm 96 2440 96 2440 96 2440 96 2440
4-24 Carriage width in mm 123 3120 130 3300 130 3300 130 3300
4-25a Fork spread, min (in-in) in mm 9.0 235 9.0 235 9.0 235 9.0 235
4-25b Fork spread, max (out-out) in mm 122.4 3108 122.4 3108 122.4 3108 122.4 3108
4-31 Ground clearance, under mast with load in mm 9 219 9 227 9 227 9 227
4-32 Ground clearance, center of wheelbase in mm 16 406 20 502 20 502 20 502
4-33 Minimum aisle width (add load length) in mm 422 10,714 423 10,747 423 10,753 452 11,482
4-35 Outside turning radius in mm 244 6185 244 6185 244 6185 270 6848
8-7 Hydraulic tank capacity gal L 86 326 86 326 86 326 86 326
8-8 Fuel tank capacity gal L 96 364 96 364 96 364 96 364
PERFORMANCE TIER 4 FINAL CUMMINS QSB 6.7L ENGINE
PERFORMANCE (TIER 4 FINAL)

5-1a Travel speed with load mph km/h 16 25 16 25 16 25 16 25

5-1b without load mph km/h 16 25 16 25 16 25 16 25
5-2a Lifting speed with load ft/min m/s 67 0.34 53 0.27 53 0.27 53 0.27
5-2b without load ft/min m/s 69 0.35 57 0.29 57 0.29 57 0.29
5-3a Lowering speed with load ft/min m/s 98 0.50 98 0.50 98 0.50 98 0.50
5-3b without load ft/min m/s 98 0.50 98 0.50 98 0.50 98 0.50
5-6 Drawbar Pull - Max lbs kN 54,400 242 55,100 245 54,900 244 54,900 244
5-7 Gradeability no load / rated load - 1 mph (1.6 km/h) % 35 / 42 35/36 35 / 34 36 / 33
PERFORMANCE TIER 3 CUMMINS QSB 6.7L ENGINE
5-1a Travel speed with load mph km/h 16 25 16 25 16 25 16 25
PERFORMANCE (TIER 3)

5-1b without load mph km/h 16 25 16 25 16 25 16 25

5-2a Lifting speed with load ft/min m/s 65 0.33 53 0.27 53 0.27 53 0.27
5-2b without load ft/min m/s 69 0.35 57 0.29 57 0.29 57 0.29
5-3a Lowering speed with load ft/min m/s 98 0.50 98 0.50 98 0.50 98 0.50
5-3b without load ft/min m/s 98 0.50 98 0.50 98 0.50 98 0.50
5-6 Drawbar Pull - Max lbs kN 54,600 243 55,500 247 55,100 245 55,100 245
5-7 Gradeability no load / rated load - 1 mph (1.6 km/h) % 35 / 42 35/36 35 / 34 36 / 34

CERTIFICATION: These Hyster lift trucks meet design specifications of Part II ANSI B56.1-1969, as required by OSHA Section 1910.178(a)(2) and also comply with Part III ANSI B56.1-
revision in effect at time of manufacture. Certification of compliance with the applicable ANSI standards appears on the lift truck. Performance specifications are for a truck equipped
as described under Standard Equipment on this Technical Guide. Performance specifications are affected by the condition of the vehicle and how it is equipped, as well as by the nature,
condition of the operating area, proper service and maintenance of the vehicle. If these specifications are critical, the proposed application should be discussed with your dealer.

4
 H550-700HD/S SPECIFICATIONS
POWERTRAINS Units Tier 4 Final Tier 3 SINGLE STAGE MAST DIMENSIONS
1-3 Power type Diesel Diesel 4.4 Lift Height 4.2 Mast 4.3 Freelift 4.5 Overall
(Top of Fork) Lowered Ht. (Top of Fork) Extended Ht.
7-1 Engine manufacturer/model Cummins QSB 6.7L Cummins QSB 6.7L
in mm in mm in mm in mm
7-2a Engine power output - rated hp kW 260 194 260 194
H550-700HD/S 111 2850 204 5169 0 0 204 5169
7-2b Engine Power output - peak hp kW 270 201 270 201
7-3 Governed speed rpm 2200 2200 2-STAGE MAST DIMENSIONS
7-4 Number of cylinders/displacement #/l 6/6.7L 6/6.7L 4.4 Lift Height 4.2 Mast 4.3 Freelift 4.5 Overall
7-5 Engine torque - max lb-ft N-m 730 990 730 990 (Top of Fork) Lowered Ht. (Top of Fork) Extended Ht.
in mm in mm in mm in mm
7-5a Turbocharger Type Variable Geometry, Water Cooled
7-9 Alternator output Amps 120 120 124 3155 139 3491 0 0 199 5016
148 3760 151 3794 0 0 223 5621
AxleTech PRLC1794 (H550HD/S);
7-10a Drive Axle manufacturer/model 172 4370 163 4099 0 0 247 6257
AxleTech PRC3806 (H620-700HD/S) H550HD/S
196 4980 175 4404 0 0 271 6841
8-0 Transmission manufacturer/model ZF WG-211 ZF WG-211
244 6200 199 5014 0 0 319 8061
Drive control/transmission: 364 9250 259 6539 0 0 439 11,111
8-1 Powershift 5F x 3R Powershift 5F x 3R
number of speeds forward/reverse
8-6 Battery voltage, rated capacity V / CCA 2 x 12 / 900 2 x 12 / 900 112 2850 137 3464 0 0 191 4836
5-10 Service brake Oil immersed (wet) disc 124 3155 143 3616 0 0 203 5141
5-11 Park brake Spring apply, dry disc 148 3760 155 3919 0 0 227 5746
172 4370 167 4224 0 0 251 6356
10-1 Working pressure for attachments psi Mpa 3265 22.51 3265 22.51 H620-700HD/S
244 6200 203 5139 0 0 323 8186
268 6810 215 5444 0 0 347 8796
364 9250 283 7174 0 0 463 11,746
388 9860 295 7479 0 0 487 12356

Rated Capacities
RATED LOAD VS. LOAD CENTER | STD PIN TYPE | U.S. CUSTOMARY RATED LOAD VS. LOAD CENTER | APRON SIDESHIFT PIN TYPE | U.S. CUSTOMARY
75000 75000
70000 70000
65000 65000
RATED LOAD (lbs)

RATED LOAD (lbs)

60000 60000
55000 55000
H550HD
50000 H620HD 50000 H550HD
H620HD
H650HD
45000 H700HD 45000 H650HD
H700HD
H550HDS H550HDS
40000 H650HDS 40000 H650HDS
H700HDS H700HDS
35000 35000
24 28 32 36 40 44 48 52 56 60 64 68 72 24 28 32 36 40 44 48 52 56 60 64 68 72
LOAD CENTER (in) LOAD CENTER (in)

Model H550HDS: 55,000 lbs. at 36 (24,948 kg at 914 mm) load center RATED LOAD VS. LOAD CENTER | DFSSFP W/ HOOK FORKS | U.S. CUSTOMARY
Model H650HDS: 65,000 lbs. at 36 (29,484 kg at 914 mm) load center
75000
Model H700HDS: 70,000 lbs. at 36 (31,752 kg at 914 mm) load center
Model H550HD: 55,000 lbs. at 48 (24,948 kg at 1219 mm) load center 70000
Model H620HD: 62,000 lbs. at 48 (28,123 kg at 1219 mm) load center
65000
Model H650HD: 65,000 lbs. at 48 (29,484 kg at 1219 mm) load center
RATED LOAD (lbs)

Model H700HD: 70,000 lbs. at 48 (31,752 kg at 1219 mm) load center 60000

Conversion Factor: 1.0 = 25.4 mm 55000

1 lb = 0.45 kg
50000 H550HD
Rated capacities are for trucks equipped with: H620HD

2-stage (lower mast) to 124 (3155 mm) maximum fork height 45000 H650HD
H700HD
122 (3100 mm) carriage width (H550HD/S) 40000 H550HDS
H650HDS
129 (3160 mm) carriage width (H620-700HD/S) H700HDS
35000
96 (2440 mm) long forks 24 28 32 36 40 44 48 52 56 60 64 68 72
Contact your dealer for other capacity information. LOAD CENTER (in)

5
 Standard Features and Options

MASTS ENGINE TIER 4 FINAL

Masts with nested channels provide excellent visibility of the Cummins 6.7L QSB 6-cylinder diesel engine delivers 270 peak
attachment and load. Mast channels, rollers, stub shafts and hp and 730 lb-ft of maximum torque. EPA Tier 4 Final engine
chain anchors are designed to provide good torsional rigidity. features cooled exhaust gas recirculation (EGR) technology
Chains are positioned on the outside of mast to enhance with selective catalytic reduction (SCR); water-cooled variable
visibility. geometry turbocharger with an integrated Diesel Exhaust Fluid
(DEF) delivery system. Innovative selectable ECO performance
CARRIAGES modes offer excellent fuel economy and maximum productivity.
A number of carriage options are available including integral Also includes:
pin-type fork positioner with individual fork control; integral 120 amp alternator.
pin-type sideshift; integral pin-type dual function sideshift fork Viscous, on-demand cooling fan saves fuel and reduces noise.
positioner (DFSSFP); apron style sideshift fork positioner with Overhead exhaust with diesel oxidation catalyst and a diluter
individual fork control. to reduce exhaust temperatures.
Requires ultra-low sulphur diesel fuel and low ash oil.
FORKS Heavy duty spinner type Sy-Klone pre-cleaner center stacked
Three kinds of forks are offered: for ease of service.

1) PIN TYPE - STANDARD PROFILE available in: ENGINE TIER 3

(H550HD/S only) 96 long x 4.13 x 11.0 Cummins 6.7L QSB 6-cylinder diesel engine delivers 270 peak
(2440 mm x 105 mm x 280 mm) hp and 730 lb-ft of maximum torque. EPA Tier 3 engine features
(H620-700HD/S only) 96 long x 4.33 x 11.8 an integrated muffler. Innovative selectable ECO performance
(2440 mm x 110 mm x 300 mm) modes offer good fuel economy and optimal productivity. Also
includes:
2) INTEGRAL PIN TYPE (FOR USE WITH DFSSFP) available in: 120 amp alternator.
(H620-700HD/S only) 96 long x 4.13 x 11.0 Viscous, on-demand cooling fan saves fuel and reduces noise.
(2440 mm x 105 mm x 280 mm) Can be used in markets where ultra-low sulphur diesel fuel
(H620-700HD/S only) 96 long x 4.33 x 11.8 and low ash oil is not available
(2440 mm x 110 mm x 300 mm)
TRANSMISSION
3) HOOK TYPE (FOR USE WITH DFSSFP) available in: ZF WG 211 5-speed powershift transmission provides smooth
(H550HD/S only) 96 long x 4.13 x 11.0 shifting, precise inching and quick acceleration
(2440 mm x 105 mm x 280 mm) 5 forward and 3 reverse gears.
Electronically controlled inching.
Cushioned clutch lock-up provides smooth shifting and
dampens drive line shift shocks.
Simple push button calibration.
Transmission lock-out prevents high-speed directional
changes.
Transmission and engine powertrain protection for excessive
engine coolant temperature, low engine oil pressure, and
excessive engine inlet air temperatures.

6
 Standard Features and Options

ELECTRICAL SYSTEM DRIVE AXLE

Sealed Deutsch connectors. Rugged drive axle features full-floating design. Wheel hubs
CANbus system for easy diagnostics of engine, transmission and rotate on large tapered roller bearings.
hydraulics.
24V electrical system with 900 CCA batteries. BRAKES
The oil-cooled wet disc brake system greatly extends brake
HYDRAULIC SYSTEM system life.
Hyster on-demand load-sensing hydraulic system introduces an
efficient way to meet hydraulic load demands: OPERATOR AREA
Based on Variable Displacement Pump (VDP) technology Ergonomically designed hydraulic controls and direction
Pump is only active when oil is needed. control lever are within easy reach.
Less heat is produced, helping oil and filters last longer. Hoses, Three steps and hand grips provide easy access to operator
seals, and components also wear less and last longer. compartment.
Engine runs quieter and at lower speeds, extending life of major Angled floor plate and pedals are positioned for operator
components. comfort.
Leak free O-Ring Face Seal (ORFS) fittings standard throughout Telescopic, tilt steer column.
the truck. Supportive mechanical full-suspension seat adjusts 8
Capable of more oil displacement even at low engine speeds. inches (200 mm) for operator comfort.
Several air suspension seat options are available
STEERING SYSTEM Steel overhead guard frame provides excellent high-
The steer axle is characterized by transverse mounted double stacking visibility.
acting cylinders, 2 non-adjustable tie rods, 2 spindles, tapered Operator Presence System (OPS) with complete hydraulic
roller bearings and 2 wheel hubs. lock out requires the operator to be in the normal
Designed for high loads and long life, the one piece axle frame operating position before any travel or movement of the
carries the axle loads and provides mounting for the spindles and mast, tilt, carriage, and attachment can be initiated. Travel
cylinder. or movement of the mast, tilt, carriage, and attachment
Axle spindles are supported by oil bathed wheel bearings and is locked out when the operator leaves the seat for more
sealed to prevent contamination entry or loss of grease. This than 2-3 seconds.
ensures that oil bearings are always lubricated and enhances Optional light groups aid visibility in low-lighted areas.
overall durability of the axle spindles. Light kits featuring innovative High Intensity Discharge
Eight high tensile bolts secure the steer cylinder providing large - Xenon (HID) and halogen technology are available to
wheel angles and greater maneuverability. Excessive external choose from.
force on the frame is avoided using this design. Optional ComforCabII features:
No steering linkage adjustments are required. Lubricating tinted, curved glass
fittings on spindle and tie rod pins are the only regular circulation fan
maintenance points. heater and defroster
Load sensed steering provides low steering effort and good electric wiper and windshield washer (front, rear, top)
performance at all engine speeds. intermittent front wiper
door retainer
STEER AXLE 3-speed fan
Non-adjustable tie rod ends provide maximum life. 12-volt auxiliary power source
dome light
many additional options to enhance comfort and
productivity

7
Standard Features and Options
STANDARD EQUIPMENT OPTIONAL EQUIPMENT
Complete truck equipped with: Cummins QSB 6.7L Tier 3 engine rated at
124 max. fork height 2-stage mast with 139 overall lowered height (H550HD/S) 260 hp (270 hp peak) with variable geometry
124 max. fork height 2-stage mast with 143 overall lowered height (H620-700HD/S) turbocharger*
122 (3100 mm) wide pin-type carriage with mechanical fork locks Masts: single-stage and various 2-stage lift heights
(without fork positioner) (H550HD/S) available
129 (3280 mm) wide pin-type carriage with mechanical fork locks Various sideshifting carriages and fork positioners
(without fork positioner) (H620-700HD/S) Coil Ram - pin carriage mounted or hook carriage
96 long forks (4.13 x 11.0 section) (H550HD/S) mounted
96 long forks (4.33 x 11.8 section) (H620-700HD/S) Various hydraulic valve control groups
Cummins QSB 6.7L Tier 4 Final engine with cooled EGR and SCR Multifunction joystick control
Wet disc brakes MONOTROL pedal direction control with direction
Sy-Klone spinner type heavy duty air intake pre-cleaner change interlock system
Premium ZF WG 211 5-speed autoshift transmission Mast tilt: 15 forward / 10 back
Axle Tech PRLC 1794 heavy duty planetary drive axles (H550HD/S) Radial and pneumatic shaped solid tires
Axle Tech PRC3806 heavy duty planetary drive axles (H620-700HD/S) Enclosed cab options:
Powertrain protection system for engine and transmission; high temp. or low oil pressure - air conditioning
On-demand load-sensing hydraulic system featuring VDP technology - trainer seat
2-function hydraulic control valve with 2 levers - multifunction display panel
CANbus electrical control system for engine, transmission and hydraulics - seatside hydraulic control levers
14.00 x 24 - 28PR bias ply treaded load pneumatic drive and steer tires (H550HD/S) - telescoping & tilting steering column
16.00 x 25 - 32PR bias ply treaded PR E4 load pneumatic drive and steer tires (H620-700HD/S) - 24-12V DC converter, 2nd outlet
Directional control lever with direction change interlock system - front (single blade), top & rear wipers
Mast tilt: 6 forward / 10 back - recirculation fan
Lockable battery disconnect switch - accessory mounting post
120 amp alternator Front and rear mud flaps
Open operator compartment with integral overhead guard, includes: Multiple seat options
seatside mini-lever hydraulic control 2- or 3-point high-visibility seat belt
multifunction display panel Powered tilting operator compartment for service
interior wide angle mirrors access
handrails for operator entry & exit Various HID and halogen light kits available
telescoping & tilting steering column Hydraulic accumulator
floor mat Lifting eyes
isolated mounting for low noise and vibration Engine block heater (110V)
24-12V DC converter Mast tilt indicator
full-suspension vinyl seat with integrated, adjustable armrest and seat belt Traction speed limiter
exterior wide angle mirrors, mounted to handrails Empty seat engine shutdown
Operator restraint system Automatic greasing system
Operator presence system Centralized greasing provision for mast chain
Electronic horn - 105 dB(A) sheaves (available on limited masts)
Visible alarm / amber strobe light
Audible backup alarm
24V electrical system Other options available through Special Products
Tilting operator compartment for service access - manual operation Engineering Development (SPED). Contact Hyster
Light Kit #1 - FRONT: 2 halogen front fender lights Company for details.
REAR: 2 halogen cab mounted lights; 2 LED stop, tail and back-up lights
Steering wheel with spinner knob
Steer wheel nut protection
Non-locking fuel cap *Available as an option in non-regulated markets only.
Literature package: operators manual, service manual, parts manual
12 months / 2,000 hours manufacturers warranty

Hyster Company Visit us online at www.hyster.com or call us at 1-800-HYSTER-1.

P.O. Box 7006
Hyster, , and Monotrol are registered trademarks of Hyster Company.
Greenville, North Carolina
Hyster products are subject to change without notice.
27835-7006
Part No. H550-700HDS/TG The Hyster Company products included in this document may be covered by US Patent 6,684,148, and other patents pending.
7/2014 Litho in U.S.A. All trucks on cover shown with optional equipment. 2014 Hyster Company. All rights reserved.