Report No.

K-TRAN: KU-05-5
FINAL REPORT

Bend Losses in Rectangular Culverts

Travis Malone
A. David Parr, Ph.D.
The University of Kansas
Lawrence, Kansas

September 2008

A Cooperative TRANSPORTATION Research program

between:

Kansas Department of Transportation

Kansas State University
The University of Kansas
 1 Report No. 2 Government Accession No. 3 Recipient Catalog No.
K-TRAN: KU-05-5
4 Title and Subtitle 5 Report Date
Bend Losses in Rectangular Culverts September 2008
6 Performing Organization Code

7 Author(s) 8 Performing Organization Report No.

Travis Malone, A. David Parr, Ph.D.

9 Performing Organization Name and Address 10 Work Unit No. (TRAIS)

The University of Kansas
Department of Civil, Environmental and Architectural Engineering
2150 Learned Hall 11 Contract or Grant No.
1530 W. 15th Street C1475
Lawrence, Kansas 66045-7609
12 Sponsoring Agency Name and Address 13 Type of Report and Period Covered
Kansas Department of Transportation Final Report
Bureau of Materials and Research July 2004 - May 2008
700 SW Harrison Street
14 Sponsoring Agency Code
Topeka, Kansas 66603-3745 RE-0378-01
15 Supplementary Notes
For more information write to address in block 9.
16 Abstract

This study investigated bend losses for open channel flow in rectangular channels or culverts. Laboratory
experiments were performed for sub-critical flow in rectangular channels with abrupt bends. Bend angles
of approximately 30, 45, 60, 75 and 90 degrees were tested. The experimental results were expressed as
empirical equations, charts and tables relating the bend loss coefficient to the bend angle. The velocity and
depth are at a location sufficiently downstream from the bend to allow the flow to return to gradually varied.
A procedure was developed to estimate head loss for gradual bends in rectangular channels flowing as
free surface flow. The bend loss coefficients for gradual bends in conduits flowing full were used to develop
an adjustment factor. This factor was used to estimate a gradual bend loss coefficient for free surface flow in
rectangular channels. The equation used to estimate the gradual bend loss coefficient was where is the abrupt
bend loss coefficient, as defined in this study.
Examples problems were presented illustrating the computation of bend loss for both an abrupt bend and
a gradual bend in a rectangular open channel.

17 Key Words 18 Distribution Statement

Rectangular culverts, bend loss, head loss, No restrictions. This document is
open channel available to the public through the
National Technical Information Service,
Springfield, Virginia 22161
19 Security 20 Security 21 No. of pages 22 Price
Classification (of this Classification xxx
report) (of this page)
Unclassified Unclassified
Form DOT F 1700.7 (8-72)
Bend Losses in rectangular Culverts

Final Report

Prepared by

Travis Malone
A. David Parr, Ph.D.
The University of Kansas
Lawrence, Kansas

A Report on Research Sponsored By

THE KANSAS DEPARTMENT OF TRANSPORTATION

TOPEKA, KANSAS

September 2008

Copyright 2008, Kansas Department of Transportation

 PREFACE

The Kansas Department of Transportations (KDOT) Kansas Transportation

Research and New-Developments (K-TRAN) Research Program funded this
research project. It is an ongoing, cooperative and comprehensive research
program addressing transportation needs of the state of Kansas utilizing
academic and research resources from KDOT, Kansas State University and
the University of Kansas. Transportation professionals in KDOT and the
universities jointly develop the projects included in the research program.

NOTICE

The authors and the state of Kansas do not endorse products or manufacturers.
Trade and manufacturers names appear herein solely because they are
considered essential to the object of this report.

This information is available in alternative accessible formats. To obtain an

alternative format, contact the Office of Transportation Information, Kansas
Department of Transportation, 700 SW Harrison, Topeka, Kansas 66603-
3745 or phone (785) 296-3585 (Voice) (TDD).

DISCLAIMER

The contents of this report reflect the views of the authors who are responsible
for the facts and accuracy of the data presented herein. The contents do not
necessarily reflect the views or the policies of the state of Kansas. This report
does not constitute a standard, specification or regulation.

ii
 ABSTRACT

This study investigated bend losses for open channel flow in rectangular

channels or culverts. Laboratory experiments were performed for subcritical flow

in rectangular channels with abrupt bends. Bend angles of approximately 30, 45,

60, 75 and 90 degrees were tested. The local head loss due to an abrupt bend

Vds2
can be expressed by the equation hbend = Kb where K b = the bend loss
2g

coefficient, Vds = velocity downstream from the bend and g = gravitational

acceleration. The experimental results were expressed as empirical equations,

charts and tables relating the bend loss coefficient to the bend angle, and the

velocity and depth in the channel downstream from the bend expressed as the

Vds
dimensionless Froude Number, Fr = , where y ds = the flow depth
gy ds

downstream from the bend . The velocity and depth are at a location sufficiently

downstream from the bend to allow the flow to return to gradually varied.

A procedure was developed to estimate head loss for gradual bends in

rectangular channels flowing as free surface flow. The bend loss coefficients for

gradual bends in conduits flowing full were used to develop an adjustment factor,

, This factor was used to estimate a gradual bend loss coefficient, K gb , for free

surface flow in rectangular channels. The equation used to estimate the gradual

bend loss coefficient was K gb = K b where K b is the abrupt bend loss coefficient,

as defined in this study.

iii
 Example problems were presented illustrating the computation of bend

loss for both an abrupt bend and a gradual bend in a rectangular open channel.

iv
 ACKNOWLEDGEMENTS

This project was supported by the Kansas Department of Transportation.

Special thanks go to Jim Richardson of KDOT, the project monitor, and Brad

Rognlie. We would also like to express our appreciation to Jim Weaver and Jay

Barnard for their help and advice on this project.

v
 TABLE OF CONTENTS

Abstract ................................................................................................................ iii

Acknowledgements ............................................................................................... v
Table of Contents................................................................................................. vi
List of Figures ..................................................................................................... vii
List of Tables ......................................................................................................viii
Chapter 1 - Bend Losses in Rectangular Culverts ................................................ 1
1.1 Introduction .............................................................................................. 1
Chapter 2 Laboratory Models ............................................................................ 3
Chapter 3 - Experimental Results ....................................................................... 11
3.1 Bend Loss Coefficient ............................................................................ 19
3.2 Design Curves and Charts for Abrupt Bend Loss Coefficients............... 23
Example Problem ........................................................................................ 23
Chapter 4 - Gradual Culvert Bends ..................................................................... 29
Example Problem ........................................................................................ 33
Chapter 5 - Summary, Conclusions and Recommendations .............................. 35
Chapter 6 - References ....................................................................................... 41
Appendix A ......................................................................................................... 43
Experimental Data ........................................................................................... 44
Design Tables and Charts ............................................................................... 54

vi
 LIST OF FIGURES

Figure 1.1: Abrupt and Gradual Bends in Rectangular Channels ......................... 1

Figure 2.1: Laboratory Set-up. .............................................................................. 4
Figure 2.2: Flume Calibration Curve ..................................................................... 6
Figure 2.3: Experimental Flume. ........................................................................... 9
Figure 2.4: Water Surface Through Bend for 90 Experiments ........................... 10
Figure 2.3: Experimental Flume .......................................................................... 10
Figure 3.1: Plot of Bend Loss Versus Velocity Head at Piezometer 16 with Linear,
Zero-Intercept Trend Lines ....................................................................... 11
Figure 3.2: Dimensionsless Bend Loss Versus Downstream Froude Number
Squared.................................................................................................... 13
Figure 3.3: Coefficients for Figure 1.6 Trend Lines as Functions of Bend Angle.14
Figure 3.4: Equation 1.9 and Experimental Data hb/yds versus Fr2ds ................... 16
Figure 3.5: Equation 3.3 and Experimental Data hb/yds versus Frds .................... 17
Figure 3.6: dimensionless head loss versus Froude number (Eq. 1.9) ............... 18
Figure 3.7: Experimental Data, Eq. 11 and Linear Trend Lines .......................... 21
Figure 3.8: Comparison of Kb from Equation 14 and Experimental Data ............ 22
Figure 3.9: Kb versus downstream Froude number squared. .............................. 24
Figure 3.10: Kb versus downstream Froude number........................................... 25
Figure 4.1: Loss Coefficients for Gradual Bends in Conduits Flowing Full (4, 5) 30
Figure 4.2: Plot of Kgb/Kgb,1 and Factor for Gradual Culvert Bends .................. 31
Figure 5.1: Comparison of Abrupt Bend Loss Coefficients from Eq. 4.3 with
Values from Other Sources ...................................................................... 37
Figure 5.2: Screen Capture of HEC-RAS Input Location for of Bend Loss
Coefficient ................................................................................................ 39
Figure A.1: Kb versus downstream Froude numbr (Report Fig. 3.10) ................. 55

vii
 LIST OF TABLES

Table 3.1: Coefficients for Trend Lines of Figure 1.7 .......................................... 14

Table 3.2: Coefficients for Trend Lines of Figure 3.3 .......................................... 15
Table 3.3: Coefficients for Trend Lines of Figures 6 and 11 ............................... 20
Table 3.2: (repeated) Coefficients for Plots of Figure 3.3.................................... 22
Table 3.4: Loss coefficients, Kb, for abrupt bends in rectangular channels. ........ 26
Table 4.1: Loss coefficients for gradual bends in conduits flowing full (4, 5) ....... 29
Table 4.2: Kgb/Kgb,1 and Factor for Gradual Bends ........................................... 31
Table 4.3: Factor versus r/Deq for Gradual Bends ............................................ 32
Table A1: Data for 30 Degree Experiments ........................................................ 44
Table A2: Data for 45.2 Degree Experiments ..................................................... 46
Table A3: Data for 58.5 Degree Experiments ..................................................... 48
Table A4: Data for 76 Degree Experiments ........................................................ 50
Table A5: Data for 90.5 Degree Experiments ..................................................... 52
Table A6: Loss Coefficients, Kb, for Abrupt Bends in Rectangular Channels
(Report Table 3.4) .................................................................................... 55
Table A7: Factor versus r/Deq for Gradual Bends (Report Table 7) ................. 55

viii
 CHAPTER 1 - BEND LOSSES IN RECTANGULAR

CULVERTS

1.1 Introduction

This study considers bend losses for open channel flow in rectangular

channels. Figure 1.1 is a definition sketch showing abrupt and gradual bends

where is the bend angle.

Abrupt Bend Gradual Bend

rc

Figure 1.1: Abrupt and Gradual Bends in Rectangular Channels

Laboratory experiments were performed for subcritical flow in rectangular

channels with abrupt bends. Bend angles of approximately 30, 45, 60, 75 and 90

degrees were tested. A laboratory flume was constructed specifically for this

project. The flume was modified (rebuilt) for each of the five bend angles

considered. Experimental results were expressed as empirical equations, charts

and tables that can be used to determine bend loss as functions of bend angle

and the velocity and depth in the channel downstream from the bend.

Specifically, an abrupt bend loss coefficient, Kb, was derived that is a function of

1
the bend angle and the Froude number at the downstream end of the abrupt

bend.

A procedure was developed for determining the head loss for gradual

bends in rectangular channels. Loss coefficients for gradual bends in conduits

flowing full (4, 5) were used to develop an adjustment factor, . The gradual bend

loss coefficient, Kgb, is obtained by multiplying Kb by .

2
 CHAPTER 2 - LABORATORY MODELS

Figure 2.1 shows the plan view of the laboratory flume for the 45 degree

bend experiments. The flume was constructed mostly of marine plywood. The

flume cross section is 6 inches wide and 12 inches deep. Water was supplied to

the flume from the constant head tank of the KU hydraulics laboratory. The flume

is equipped with upstream and downstream head tanks. The headwater

(upstream) tank contains a level, fixed overflow weir. Water flows from the

headwater tank to the rectangular channel through a 10.5-inch long transition

section. The tailwater (downstream) tank has an adjustable-height 16.9-inch long

overflow weir that is used to control the tailwater elevation in the channel. After

overtopping the adjustable overflow weir in the tailwater tank, the water returns to

the laboratory sump system.

3
 Man
om
1 2 3 4 5 6 7 8 Ban eter
ks
Manifold 52.5 9
10
Overflow Weir 11
12
13
14
6 11
15
16
1
1

13.5

36.6
5
15.3 2.
16.7 10.5 88 5

Bend Section

Differential 7

4
5
Manometer

Orifice
.6
39
.9
28 16
.8

10
Overflow Weir .1

p

Inflow
u m
s
to
ow

Valve
fl
ut
O

Figure 2.1: Laboratory Set-up.

 A different bend section was constructed for each bend angle 30, 45, 60, 75

and 90 degrees. (The actual constructed angles were 30, 45.2, 58.5, 76 and 90.5

degrees.) The centerline length of each bend section was 22- long with 11

upstream and downstream from the bend, respectively. Changing a bend section

was not a simple process since the channel and tailwater tank downstream from the

bend section had to be moved to different positions for each bend angle. The head

tank and the channel upstream from the bend section remained stationary.

A 4-inch PVC line carried water to the flume. The discharge was controlled

with a gate valve at the upstream end of the supply line. An orifice plate was

constructed and installed in the supply line to facilitate flow calibration and, during

experiments, to establish the desired discharge. Piezometers installed just upstream

and downstream from the orifice plate were connected to a 2-tube manometer in

order to read the head loss across the orifice. The orifice was calibrated

volumetrically using a tank built specifically for that task. A rating curve of discharge

versus head loss across the orifice plate is shown in Figure 2.2.

The water surface elevations upstream and downstream from the bend were

measured using a series of piezometers installed in the flume bed. (See Figure 2.1.)

The piezometer readings were read from a manometer bank then the readings were

used to determine the local depths of flow. The piezometers were located from 1.71

to 5.21 feet upstream from the bend and from 1.71 to 5.21 feet downstream from the

bend and were spaced at 6-inch intervals. (A total of 16 piezometers were installed

but the next to last piezometer, No. 15, did not work.) Knowing the flume discharge

5
and the flow depth and bed elevation of each piezometer, the total head

( H = z + p / + V 2 / 2 g ) could be calculated for each piezometer location.

0.8

0.7 0.5
Q = 0.176 (del h)
2
R = 0.999
0.6
Discharge, Q (cfs)

0.5

0.4

0.3

0.2

0.1

0
0 5 10 15 20

Differential Manometer Reading, del h (ft of water)

Figure 2.2: Flume Calibration Curve

The Bernoulli equation is only valid at cross sections where the pressure

distribution is hydrostatic. This condition is met for free surface flow when the water

surface is level across the section and the streamlines are straight and parallel (or

nearly so). Hydrostatic pressure distribution occurs in open channels for regions of

uniform or gradually varied flow. Rapidly varied flow regions do not meet the

conditions for hydrostatic pressure distribution and the Bernoulli equation should not

apply in those regions.

6
 Initially readings were taken at all 15 working piezometers to determine the

behavior of the flow through the channel. Rapidly varied flow was observed in a

region that extended downstream from the bend to the first few (or more)

piezometers. Strong transverse and vertical variations in the velocity distribution

were evident as the flow came around the bend. The length of the rapidly varied flow

region appeared to lengthen as the velocity increased. The flow smoothed-out and

became gradually varied by the time it reached the most downstream piezometer

(Piezometer 16) for all experiments. Consequently, the total head loss was

determined for the reach between Piezometers 2 and 16.

The total head loss between Piezometers 2 and 16 consisted of friction loss

and bend loss. Thus, the bend loss was the total head loss minus the estimated

friction loss between Piezometers 2 and 16. The equations below show the method

used to compute the total head loss between Piezometers 2 and 16.

H 2 = H 16 + hloss Equation 2.1

V22 V2
y2 + z2 + = y16 + z16 + 16 + hloss Equation 2.2
2g 2g

Where y = depth (feet), z = bed elevation (feet) and V = velocity (feet/sec) =

Q/(0.5y) where Q is in cubic feet per second. Due to the construction materials, the

flume was not exactly horizontal nor was it the same for each series of experiments.

Thus, the bed elevations for Piezometers 2 and 16 were determined for each set-up

by establishing a pooled-water condition in the flume then measuring the depths at

each location. The distance between Piezometers 2 and 16 was 9.92 feet.

7
 The loss term includes the bend loss and the friction loss. The friction loss

was estimated using the Mannings equation in the form shown below.

n 2V 2 L
hf = Equation 2.3
(1.49)2 R 4 / 3
Where

Q Q
V = = Equation 2.4
A (0.5 y )

R=
A
=
(0.5 y )
Equation 2.5
Pw (0.5 + 2 y )

y 2 + y16
y= Equation 2.6
2

A Manning n-value of 0.010 was used. The sides of the flume were

constructed of sanded marine grade plywood and painted with epoxy paint. This

provided a very smooth sidewall condition. This n-value corresponds to table values

for planed wood. Also, the n-value of 0.010 provided reasonable results in allocating

the total head loss to friction and to bend loss. L was equal to 9.92 feet - the

distance between Piezometers 2 and 16.

Figure 2.3 shows the bend loss flume from the tailwater tank. Figure 2.4

shows pictures of the water surface elevations for three 90.5 degree experiments.

These pictures were taken with the camera directed in the upstream direction toward

the bend.

8
9
Figure 2.3: Experimental Flume.
10
Frds = 0.35 Frds = 0.54
Frds = 0.74

Figure 2.4: Water Surface Through Bend for 90 Experiments

 CHAPTER 3 - EXPERIMENTAL RESULTS

A total of 190 experiments were performed. The results are summarized in

Tables 3.1-3.5 in Appendix A. The bend loss, hb, is the total loss, h, minus the estimated

friction loss, hf, between Piezometers 2 and 16. Figure 3.1 is a plot of bend loss versus

the downstream velocity head (Piezometer 16).

0.12

0.10

0.08
hb (ft)

0.06

0.04

0.02

0.00
0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16
2
V /2g (ft)
30 deg 45.2 deg 58.5 deg 76 deg 90.5 deg

Figure 3.1: Plot of Bend Loss versus Velocity Head at Piezometer 16 with Linear, Zero-
Intercept Trend Lines

The standard bend loss equation has the form shown below in Equation 3.1

where Kb is the bend loss coefficient. Typically, Kb is assumed to be constant with

respect to velocity. This assumption would dictate that the data would vary linearly with

the velocity head. It is apparent from Figure 3.1 that only the data for the 30 degree

angle experiments follows a linear trend line.

11
 V2
hb = K b Equation 3.1
2g

Figure 3.2 is a plot of dimensionless bend loss versus the downstream Froude

number squared. A second possible independent variable would be the downstream

depth, yds, divided by the flume width, W. For this study the parameter yds/W ranged

from 0.6 to 1.87 and over that range the parameter appeared to have little effect. Many

types of trend lines were examined until the second-order polynomial shown in Equation

3.2 was selected. The trend lines were forced through the (0,0) point which is physically

reasonable.

= a ( Frds2 ) + b ( Frds2 ) = aFrds4 + bFrds2

hb 2
h* = Equation 3.2
yds

Where Fr2ds = V2ds/gyds and yds = the depth at Piezometer 16. The coefficients a

and b are functions of the bend angle, . Each of the trend line equations is shown on

Figure 3.1 with y representing h* and x representing Fr2ds.

The coefficients a and b for the trend lines of Figure 3.2 shown in Table 1.1 are

plotted in Figure 3.2 versus bend angle.

12
 0.20
y = -0.2967x2 + 0.4905x
R2 = 0.9866

y = -0.2244x2 + 0.374x
R2 = 0.9671
0.15

y = -0.1452x2 + 0.2815x
R2 = 0.9901

0.10

13
h* = hb/yds
y = -0.0898x2 + 0.1431x
0.05 R2 = 0.8569

y = -0.0598x2 + 0.0725x
R2 = 0.4291

0.00
0.0 0.4 0.7 1.1
Fr2ds
30 deg 45.2 deg 58.5 deg 76 deg 90.5 deg

Figure 3.2: Dimensionsless Bend Loss versus Downstream Froude Number Squaerd
(Note: The trend lines were created in Excel 2003. Excel 2007 produces different coefficients.)
Table 3.1: Coefficients for Trend Lines of Figure 1.7

From Figure 1.7

Bend Angle, a b
(1) (2)
90.5 -0.2967 0.4905
76 -0.2244 0.3740
58.5 -0.1452 0.2815
45.2 -0.0898 0.1431
30 -0.0598 0.0725

0.6

0.5 b = 8.216E-06 2 + 6.016E-03 - 1.223E-01

R2 = 9.893E-01
0.4
Coefficients a and b

0.3

0.2

0.1
a = -3.070E-05 2 - 3.031E-04 - 2.014E-02
0.0 R2 = 9.979E-01

-0.1

-0.2

-0.3

-0.4
30 45 60 75 90

Bend Angle, , in degrees

Figure 3.3: Coefficients for Figure 1.6 Trend Lines as Functions of Bend Angle.

14
 The coefficients for the equations shown in Figure 3.3 are presented in Table

3.2. These values will be used to generate a predictive equation for angles other

Table 3.2: Coefficients for Trend Lines of Figure 3.3

than the ones tested in the flume.

Parameters for Coefficient a Parameters for Coefficient b

m n o p q r
-3.0702 E-05 -3.0310E-04 -2.0139E-02 8.2164E-06 6.0159E-03 -1.2229E-01

The predictive equation is given below.

= aFrds4 + bFrds2 = ( m 2 + n + o ) Frds4 + ( p 2 + q + r ) Frds2

hb
Equation 3.3
yds

Where = bend angle in degrees; Frds = V2ds/yds; hb= bend loss and yds =

depth downstream from the bend. Figure 3.4 shows the experimental data plotted as

hb/yds versus Fr2ds on curves generated using Equation 3.3 for the angles tested.

The fit for Equation 3.3 is not as good as the fits for the individual trend lines shown

in Figure 3.2. Nonetheless it shows that Equation 3.3 can be used to generate data

for intermediate bend angles. Figure 3.5 is a plot of hb/yds versus Frds rather than

Fr2ds. The use of the Froude number rather than the Froude number squared for

the abscissa is probably better since HEC-RAS output tables have the Froude

number as an optional table parameter.

Figure 3.6 shows Equation 3.3 plotted for bend angles of 30, 40, 50, 60, 70,

80 and 90 degrees. This curve can be used to determine the head loss for a culvert

given the bend angle and the depth and Froude number for the culvert in the region

downstream from the bend where flow is deemed hydrostatic.

15
 0.25

0.2
h* = hb/yds

0.15

0.1

0.05

0
0 0.2 0.4 0.6 0.8 1
2
Fr ds

30 deg Eq.9 45.2 deg Eq.9 58.5 deg Eq.9

76 deg Eq.9 90.5 deg Eq.9 30 deg data
45.2 deg data 58.5 deg data 76 deg data
90.5 deg data

2
Figure 3.4: Equation 1.9 and Experimental Data hb/yds versus Fr ds

16
 0.25

0.2
h* = hb/yds

0.15

0.1

0.05

0
0 0.2 0.4 0.6 0.8 1
Frds
30 deg Eq. 9 45.2 deg Eq. 9 58.5 deg Eq. 9
76 deg Eq. 9 90.5 deg Eq. 9 30 deg data
45.2 deg data 58.5 Data 76 deg data
90.5 deg data

Figure 3.5: Equation 3.3 and Experimental Data hb/yds versus Frds

17
 0.2 o
90

0.18
o
80
0.16
o
70
0.14

o
0.12 60

0.1
o

18
50
0.08

h* = hb/yds
0.06 o
40

0.04

0.02 o
30

0
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1

Frds
Figure 3.6: Dimensionless Head Loss versus Froude Number (Eq. 1.9)
3.1 Bend Loss Coefficient

Equation 2.4 can be expressed as a function of the Froude number as follows.

Vds2 hb K b Vds2
hb = K b =
2g y ds y ds 2 g

hb K b V d2 K
= = b F r2
y ds 2 gy ds 2

Or rearranging

2 hb
Kb = Equation 3.4
Frds2 yds

Substituting Equation 3.3 from the experimental data analysis into Equation 3.4

yields.

hb
= aFrds4 + bFrds2 (Equation 3.3)
yds

2
2 ( )
Kb = aFrds4 + bFrds2
Frds

K b = ( 2a ) Frds2 + ( 2b ) Equation 3.5

Rearranging Equation gives the following expression that is used to determine the

bend loss coefficient for the experimental data.

K b = hb / (Vds2 / 2 g ) Equation 3.6

The experimental values of Kb are shown in Column 16 in the Data Tables

included in the Appendix A. The Kb experimental values are plotted versus Fr2ds in Figure

3.7. The solid lines represent Equation 3.5 using the a- and b-values from the previous

19
analysis of the data shown in Figure 3.2. Linear trend line fits for each of the bend angles

are shown as dashed lines and represented by the equation below.

K b = Frds2 + Equation 3.7

Where and are the trend line coefficients.

Table 3.3 below compares and with the values obtained by multiplying the

coefficients a and b by 2. Equation 3.5 indicates that the values in Columns 3 and 4

should, perhaps, equal the respective values in Columns 5 and 6. They are not quite the

same due to differences in the curve fitting schemes used to derive the values.

Parameters a and b were based on a second-degree polynomial trend lines while and

were based on linear trend lines. Both processes used Fr2ds as the independent variable.

Comparing the solid and dashed lines in Figure 3.7 shows that the differences are not

large in the regions of interest. We will use the values in Columns 1 and 2 of Table 3.3 to

develop the design charts summarizing the experimental data. Figure 3.8 shows a plot of

values predicted using Eq. 3.5 versus experimental values of Kb. The R2 for the plot is

0.951.

Table 3.3: Coefficients for Trend Lines of Figures 6 and 11

From Fig. 3.2 Doubled Values Trend Lines, Fig. 3.6

Bend Angle, ? a b 2a 2b ? ?
(1) (2) (3) (4) (5) (6)
90.5 -0.2967 0.4905 -0.5934 0.9810 -0.6041 0.9857
76 -0.2244 0.3740 -0.4488 0.7480 -0.5245 0.7814
58.5 -0.1452 0.2815 -0.2904 0.5630 -0.3063 0.5708
45.2 -0.0898 0.1431 -0.1796 0.2862 -0.1879 0.2891
30 -0.0598 0.0725 -0.1196 0.1450 -0.1488 0.1594

20
 1.2

1.0

0.8
Kb

0.6

0.4

0.2

0.0
0.0 0.2 0.4 0.6 0.8

Fr2ds
30 data 45.2 data 58.5 data 76 data 90.5 data

Figure 3.7: Experimental Data, Eq. 11 and Linear Trend Lines

The predictive equation for Kb is given below by combining Equation 3.5 and the

parameters from Table 3.2 (repeated below for reference).

K b = 2aFrds2 + 2b = 2 ( m 2 + n + o ) Frds2 + 2 ( p 2 + q + r ) Equation 3.8

21
 Where = bend angle in degrees; Frds = V2ds/yds; hb= bend loss and yds = depth

downstream from the bend. Figure 3.8 is a plot of measured versus values predicted

using Eq. 3.8. The R2 value is 0.950.

Table 3.2: (repeated) Coefficients for Plots of Figure 3.3

Parameters for Coefficient a Parameters for Coefficient b
m n o p q r
-3.0702 E-05 -3.0310E-04 -2.0139E-02 8.2164E-06 6.0159E-03 -1.2229E-01

1.2

1.0
R = 0.950
Kb Equation 14

0.8

0.6

0.4

0.2

0.0
0.0 0.2 0.4 0.6 0.8 1.0 1.2
Kb Experimental

Figure 3.8: Comparison of Kb from Equation 14 and Experimental Data

22
3.2 Design Curves and Charts for Abrupt Bend Loss Coefficients

Figures 3.9 and 3.10 show the bend loss coefficient Kb versus Fr2ds and Frds,

respectively, based on Equation 3.8. Users may prefer Figure 3.10 since it involves only

the downstream Froude number. Alternatively, users can read Kb directly from Table 3.4.

Example Problem

Assume a 12x10 RCB carries 750 cfs and has a depth downstream from the bend

of 7.5 feet. Determine the bend loss if a 40 degree abrupt bend exists in the culvert. (The

depth and velocity can be determined using HEC-RAS by modeling the culvert as a

channel with a lid. This works very well if you make sure the lid is thick enough to contain

the energy grade line elevation. In other words, the top of the lid must be higher than the

energy grade line throughout the culvert. If you do not make the lid high enough, some of

the water will flow above the culvert.)

Q 700
Vds = = = 8.33 fps
A (12*7) )
Vds 8.33
Fr = = = 0.555
gy ( 32.2 )( 7 )

From Figure 3.10 or Table 3.4.

K b = 0.213
Vds2 8.332
hL = Kb = ( 0.213) = 0.230 ft
2g 2 ( 32.2 )

Alternately, from Figure 3.6

Frds = 0.555 h* = hb / yds = 0.0329

hb = yds ( hb / yds ) = 7(0.0329) = 0.230 ft

23
 1.0

0.9 Vds2
hL = Kb
0.8 2g
o
90
0.7
o
80
0.6
o
70

Kb
0.5
o
60

24
0.4
o
50
0.3
o
0.2
40

o
0.1 30

0.0
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8

Fr2ds= V 2 ds /(g y ds )
Figure 3.9: Kb versus Downstream Froude Number Squared.
 1.0

0.9 Vds2
o hL = Kb
90 2g
0.8
o
0.7
80

o
0.6 70

0.5 o

Kb
60

25
0.4
o
50
0.3
o
40
0.2
o
30
0.1

0.0
0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9

Frds= Vds/(gyds)1/2

Figure 3.10: Kb versus Downstream Froude Number.

 Table 3.4: Loss Coefficients, Kb, for Abrupt Bends in Rectangular Channels.

Abrupt Bend Angle, , in degrees

Fr
30 35 40 45 50 55 60 65 70 75 80 85 90
0.20 0.127 0.191 0.256 0.322 0.389 0.457 0.525 0.593 0.663 0.733 0.804 0.875 0.948
0.21 0.126 0.191 0.256 0.322 0.388 0.455 0.523 0.592 0.661 0.731 0.802 0.873 0.945
0.22 0.126 0.190 0.255 0.321 0.387 0.454 0.522 0.591 0.660 0.729 0.800 0.871 0.943
0.23 0.125 0.189 0.254 0.320 0.386 0.453 0.521 0.589 0.658 0.727 0.798 0.869 0.940
0.24 0.125 0.189 0.254 0.319 0.385 0.452 0.519 0.587 0.656 0.725 0.795 0.866 0.937
0.25 0.124 0.188 0.253 0.318 0.384 0.451 0.518 0.586 0.654 0.723 0.793 0.863 0.934
0.26 0.123 0.187 0.252 0.317 0.383 0.449 0.516 0.584 0.652 0.721 0.791 0.861 0.931
0.27 0.123 0.187 0.251 0.316 0.382 0.448 0.515 0.582 0.650 0.719 0.788 0.858 0.928
0.28 0.122 0.186 0.250 0.315 0.381 0.447 0.513 0.580 0.648 0.716 0.785 0.855 0.925
0.29 0.122 0.185 0.249 0.314 0.379 0.445 0.511 0.578 0.646 0.714 0.783 0.852 0.922
0.30 0.121 0.184 0.248 0.313 0.378 0.444 0.510 0.576 0.644 0.711 0.780 0.849 0.918
0.31 0.120 0.184 0.247 0.312 0.377 0.442 0.508 0.574 0.641 0.709 0.777 0.845 0.914
0.32 0.120 0.183 0.246 0.310 0.375 0.440 0.506 0.572 0.639 0.706 0.774 0.842 0.911
0.33 0.119 0.182 0.245 0.309 0.374 0.439 0.504 0.570 0.636 0.703 0.771 0.839 0.907
0.34 0.118 0.181 0.244 0.308 0.372 0.437 0.502 0.568 0.634 0.700 0.767 0.835 0.903
0.35 0.117 0.180 0.243 0.307 0.371 0.435 0.500 0.565 0.631 0.697 0.764 0.831 0.899
0.36 0.116 0.179 0.242 0.305 0.369 0.433 0.498 0.563 0.628 0.694 0.761 0.827 0.895

26
0.37 0.116 0.178 0.241 0.304 0.367 0.431 0.496 0.560 0.626 0.691 0.757 0.824 0.890
0.38 0.115 0.177 0.239 0.302 0.366 0.429 0.493 0.558 0.623 0.688 0.754 0.820 0.886
0.39 0.114 0.176 0.238 0.301 0.364 0.427 0.491 0.555 0.620 0.685 0.750 0.815 0.881
0.40 0.113 0.175 0.237 0.299 0.362 0.425 0.489 0.553 0.617 0.681 0.746 0.811 0.877
0.41 0.112 0.174 0.236 0.298 0.360 0.423 0.486 0.550 0.614 0.678 0.742 0.807 0.872
0.42 0.111 0.173 0.234 0.296 0.359 0.421 0.484 0.547 0.611 0.674 0.738 0.802 0.867
0.43 0.110 0.171 0.233 0.295 0.357 0.419 0.481 0.544 0.607 0.671 0.734 0.798 0.862
0.44 0.109 0.170 0.231 0.293 0.355 0.417 0.479 0.541 0.604 0.667 0.730 0.793 0.857
0.45 0.108 0.169 0.230 0.291 0.353 0.414 0.476 0.538 0.600 0.663 0.726 0.788 0.851
0.46 0.107 0.168 0.229 0.290 0.351 0.412 0.473 0.535 0.597 0.659 0.721 0.784 0.846
0.47 0.106 0.166 0.227 0.288 0.349 0.410 0.471 0.532 0.593 0.655 0.717 0.779 0.841
0.48 0.105 0.165 0.225 0.286 0.346 0.407 0.468 0.529 0.590 0.651 0.712 0.773 0.835
0.49 0.104 0.164 0.224 0.284 0.344 0.405 0.465 0.525 0.586 0.647 0.707 0.768 0.829
0.50 0.103 0.162 0.222 0.282 0.342 0.402 0.462 0.522 0.582 0.642 0.703 0.763 0.823
0.51 0.102 0.161 0.221 0.280 0.340 0.399 0.459 0.519 0.578 0.638 0.698 0.758 0.817
0.52 0.100 0.160 0.219 0.278 0.337 0.397 0.456 0.515 0.574 0.634 0.693 0.752 0.811
0.53 0.099 0.158 0.217 0.276 0.335 0.394 0.453 0.512 0.570 0.629 0.688 0.746 0.805
0.54 0.098 0.157 0.216 0.274 0.333 0.391 0.450 0.508 0.566 0.625 0.683 0.741 0.799
0.55 0.097 0.155 0.214 0.272 0.330 0.388 0.446 0.504 0.562 0.620 0.677 0.735 0.792
0.56 0.095 0.154 0.212 0.270 0.328 0.386 0.443 0.501 0.558 0.615 0.672 0.729 0.786
0.57 0.094 0.152 0.210 0.268 0.325 0.383 0.440 0.497 0.554 0.610 0.667 0.723 0.779
0.58 0.093 0.151 0.208 0.266 0.323 0.380 0.436 0.493 0.549 0.605 0.661 0.717 0.772
0.59 0.092 0.149 0.206 0.263 0.320 0.377 0.433 0.489 0.545 0.600 0.655 0.710 0.765
 Table 3.4: Loss Coefficients, Kb, for Abrupt Bends in Rectangular Channels. (cont.)

Abrupt Bend Angle, , in degrees

Fr
30 35 40 45 50 55 60 65 70 75 80 85 90
0.59 0.092 0.149 0.206 0.263 0.320 0.377 0.433 0.489 0.545 0.600 0.655 0.710 0.765
0.60 0.090 0.147 0.204 0.261 0.317 0.374 0.429 0.485 0.540 0.595 0.650 0.704 0.758
0.61 0.089 0.146 0.202 0.259 0.315 0.370 0.426 0.481 0.535 0.590 0.644 0.698 0.751
0.62 0.087 0.144 0.200 0.256 0.312 0.367 0.422 0.477 0.531 0.585 0.638 0.691 0.744
0.63 0.086 0.142 0.198 0.254 0.309 0.364 0.418 0.472 0.526 0.579 0.632 0.684 0.736
0.64 0.085 0.141 0.196 0.252 0.306 0.361 0.415 0.468 0.521 0.574 0.626 0.678 0.729
0.65 0.083 0.139 0.194 0.249 0.303 0.357 0.411 0.464 0.516 0.568 0.620 0.671 0.721
0.66 0.082 0.137 0.192 0.247 0.300 0.354 0.407 0.459 0.511 0.562 0.613 0.664 0.713
0.67 0.080 0.135 0.190 0.244 0.297 0.350 0.403 0.455 0.506 0.557 0.607 0.656 0.706
0.68 0.079 0.133 0.188 0.241 0.294 0.347 0.399 0.450 0.501 0.551 0.600 0.649 0.698
0.69 0.077 0.132 0.185 0.239 0.291 0.343 0.395 0.445 0.496 0.545 0.594 0.642 0.689
0.70 0.075 0.130 0.183 0.236 0.288 0.340 0.391 0.441 0.490 0.539 0.587 0.634 0.681

27
0.71 0.074 0.128 0.181 0.233 0.285 0.336 0.386 0.436 0.485 0.533 0.580 0.627 0.673
0.72 0.072 0.126 0.179 0.231 0.282 0.332 0.382 0.431 0.479 0.527 0.573 0.619 0.664
0.73 0.071 0.124 0.176 0.228 0.279 0.329 0.378 0.426 0.474 0.520 0.566 0.612 0.656
0.74 0.069 0.122 0.174 0.225 0.275 0.325 0.373 0.421 0.468 0.514 0.559 0.604 0.647
0.75 0.067 0.120 0.171 0.222 0.272 0.321 0.369 0.416 0.462 0.508 0.552 0.596 0.638
0.76 0.065 0.118 0.169 0.219 0.269 0.317 0.365 0.411 0.457 0.501 0.545 0.588 0.629
0.77 0.064 0.116 0.166 0.216 0.265 0.313 0.360 0.406 0.451 0.495 0.537 0.579 0.620
0.78 0.062 0.113 0.164 0.213 0.262 0.309 0.355 0.401 0.445 0.488 0.530 0.571 0.611
0.79 0.060 0.111 0.161 0.210 0.258 0.305 0.351 0.395 0.439 0.481 0.522 0.563 0.602
0.80 0.058 0.109 0.159 0.207 0.255 0.301 0.346 0.390 0.433 0.474 0.515 0.554 0.592
0.81 0.057 0.107 0.156 0.204 0.251 0.297 0.341 0.384 0.426 0.467 0.507 0.546 0.583
0.82 0.055 0.105 0.154 0.201 0.247 0.292 0.336 0.379 0.420 0.460 0.499 0.537 0.573
0.83 0.053 0.102 0.151 0.198 0.244 0.288 0.331 0.373 0.414 0.453 0.491 0.528 0.563
0.84 0.051 0.100 0.148 0.195 0.240 0.284 0.326 0.368 0.408 0.446 0.483 0.519 0.554
0.85 0.049 0.098 0.145 0.191 0.236 0.279 0.321 0.362 0.401 0.439 0.475 0.510 0.544
0.86 0.047 0.096 0.143 0.188 0.232 0.275 0.316 0.356 0.394 0.431 0.467 0.501 0.533
0.87 0.046 0.094 0.141 0.186 0.230 0.272 0.313 0.353 0.390 0.427 0.462 0.495 0.527
28
 CHAPTER 4 - GRADUAL CULVERT BENDS

The head loss for gradual culvert bend can be determined by the equation.

Vds2
hb = K gb Equation 4.1
2g

Where Kgb is the gradual bend loss coefficient. Values of Kgb for conduits flowing

full are given in Table 4.1 as a function of the radius of curvature of the bend, r, divided by

the equivalent culvert diameter, Deq (4, 5). For circular culverts, Deq is the pipe diameter.

For noncircular culverts the following equation is used to define Deq.

Deq = 4 A / Equation 4.2

Where A is the cross sectional area. The values in Table 4.1 are plotted in Figure

4.1.

Table 4.1: Loss Coefficients for Gradual Bends in Conduits Flowing Full (4, 5)
Kgb
rc/Deq
90 45 22.5
1
2 3 4
1 0.5 0.37 0.25
2 0.3 0.22 0.15
4 0.25 0.19 0.12
6 0.15 0.11 0.08
8 0.15 0.11 0.08

29
 0.6

0.5

0.4

gb
K 0.3

0.2

0.1

0
0 1 2 3 4 5 6 7 8

rc/Deq
90 degrees 45 degrees 22.5 degrees

Figure 4.1: Loss Coefficients for Gradual Bends in Conduits Flowing Full (4, 5)

The Kgb-values in the top row of Table 4.1 are 0.5, 0.37 and 0.25, respectively, for

the 90, 45 and 22.5 degree bends. These values will be called Kgb,1-values and are the

bend loss coefficients for r/Deq = 1. The values in Table 4.2 are the values in Table 4.1

divided by the appropriate Kgb,1-value . The -values in Table 4.2 are plotted in Figure

4.2. Both Table 4.2 and Figure 4.2 show that the variation of with r/Deq is nearly the

same for each of the three bend angles. The dashed line in the Figure 4.2 is a plot of the

average -values shown in Column 5 of Table 4.2. These average values will be used

herein to estimate bend losses for gradual bends in rectangular open channels using the

results of this study.

30
Table 4.2: Kgb/Kgb,1 and Factor for Gradual Bends
Kgb
rc/Deq Average
90 45 22.5
1 2 3 4 5

1 1 1 1 1
2 0.600 0.595 0.600 0.598
4 0.500 0.514 0.480 0.498
6 0.300 0.297 0.320 0.306
8 0.300 0.297 0.320 0.306

1.2

1
and Kgb/Kgb,1

0.8
,1

0.6

0.4

0.2

0
0 1 2 3 4 5 6 7 8

rc/Deq
90 Degrees 45 degrees 22.5 degrees Average

Figure 4.2: Plot of Kgb/Kgb,1 and Factor for Gradual Culvert Bends

31
 Table 4.3 shows -values for r/Deq ranging from 1 to 8. The table was developed

from the values in Column 5 of Table 4.2 by linear interpolation. It will be assumed that

the values in Table 4.2 can be applied to the abrupt bend loss coefficient defined by Eq.

3.8. The abrupt bend loss coefficient, Kb, is assumed to be equivalent to the parameter

Kgb,1 in Table 4.2. Equation 4.3 shows Equation 4.1 expressed in terms of and Kb where

Kb is the bend loss coefficient for abrupt bends developed in Chapter 3 and given by Eq.

3.8.

hb = K gb
Vds2
2g
[ ] V2 V2
= K b K gb / K gb ,1 ds = K b ds
2g 2g
Equation 4.3

Table 4.3: Factor versus r/Deq for Gradual Bends

rc/Deq =Kgb/Kgb, 1
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
1 1.000 0.960 0.920 0.879 0.839 0.799 0.759 0.719 0.679 0.638
2 0.598 0.593 0.588 0.583 0.578 0.573 0.568 0.563 0.558 0.553
3 0.548 0.543 0.538 0.533 0.528 0.523 0.518 0.513 0.508 0.503
4 0.498 0.488 0.479 0.469 0.459 0.450 0.440 0.431 0.421 0.411
5 0.402 0.392 0.383 0.373 0.363 0.354 0.344 0.335 0.325 0.315
6 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306
7 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306
8 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306

The example problem below illustrates the procedure recommended for

determining the bend loss for gradual bends used in rectangular culverts using the

relationships developed in this chapter.

32
 Example Problem

A 10-ft wide rectangular culvert has a gradual 50 degree bend with a radius

curvature of 45 feet. The depth and velocity at the downstream end of the bend is known

to be 8 feet and 6 feet per second, respectively. Estimate the bend loss. (Note that the

shaded cells in Table 4.3 below are used in this example.)

V 6 Table 3.4 for 50o

Fr = = = 0.374 K b = 0.367
gy ( 32.2 ) 8
Assume K b = K gb,1 = 0.367
Deq = 4 A / = 4 ( 8*10 ) / = 4 ( 80 ) / = 10.09 ft
Interpolated from Table 4.3
r / Deq = 45 /10.09 = 4.46 = 0.454
V2 V2 62
hL = K b = ( 0.454 )( 0.367 ) = ( 0.167 ) = 0.0934 ft
2g 2g 2 ( 32.2 )

rc/Deq = Kgb/Kgb,1
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
1 1.000 0.960 0.920 0.879 0.839 0.799 0.759 0.719 0.679 0.638
2 0.598 0.593 0.588 0.583 0.578 0.573 0.568 0.563 0.558 0.553
3 0.548 0.543 0.538 0.533 0.528 0.523 0.518 0.513 0.508 0.503
4 0.498 0.488 0.479 0.469 0.459 0.450 0.440 0.431 0.421 0.411
5 0.402 0.392 0.383 0.373 0.363 0.354 0.344 0.335 0.325 0.315
6 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306
7 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306
8 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306

33
34
 CHAPTER 5 - SUMMARY, CONCLUSIONS AND

RECOMMENDATIONS

A series of experiments were performed to develop head loss due to abrupt bends

in rectangular culverts. Surprisingly, there was little information in the literature about

abrupt bends in open channels. The experiments were performed in the Hydraulics

Laboratory of the University of Kansas. A special flume was constructed for this study.

Details of the flume are given in the body of the report. The channel section was

approximately 20 feet long and 0.5-ft wide. Abrupt channel bend sections were installed

near the middle of the flume. Five sections were built with the intention of testing 30, 45,

60, 75 and 90 degree bends. The exact angles were not quite met since the flume was

constructed of marine plywood. The actual angles built and tested were 30, 45.2, 58.5, 76

and 90.5 degrees. All tests were performed for subcritical flow conditions.

A total of 190 experimental runs were performed with the Froude number varying

from 0.18 to 0.86 and yds/W varying from 0.60 to 1.87. Water was supplied to the flume

from the constant tank system of the hydraulics laboratory. Flow was controlled using a

valve and a calibrated orifice in the supply line to the flume. The total head loss was

measured from a section 4.72 feet upstream from the bend to a section that is 5.20 feet

downstream from the bend. Piezometers were used at those locations to measure the

hydrostatic head and, in turn, to determine the depths, velocities and total energy. The

head loss due to the bend was then determined by subtracting the estimated head loss

due to friction from the total measured head loss.

The experimental data were plotted and analyzed by statistical methods. Several

iterations were performed to obtain reasonable fits. Plots were presented of

35
dimensionless head loss versus the downstream Froude number. However, the more

useful plots involved expressing the bend loss coefficient, Kb, as functions of the bend

angle and the downstream Froude number.

Head loss for abrupt bends can be determined as follows.

(a) Determine the depth, yds, and velocity, Vds, at a section far
enough downstream from the culvert to assume hydrostatic
pressure distribution exists. In this study the section was located
about 10 culvert widths downstream from the bend. Typically, the
section will not need to be that far downstream.
(b) Calculate the downstream Froude number.
V
Fr =
gy

(c) Read the bend loss coefficient, Kb, from either a design chart
(Figure 3.10) or from the Table 3.4.
(d) Compute the loss due to the bend using the equation.
Vds2
hb = K b
2g
The equations below are sometimes recommended for determining bend losses in

culverts.

(http://epg.modot.mo.gov/index.php?title=750.2_Culverts and

http://www.fcd.maricopa.gov/Pub/Manuals/downloads/Hydraulics%20Design%20Manual.

pdf , respectively)

hb = K b*
V2
2g (
= 0.5
V2
)
90 2 g (Equation 4.3)
2
*V V2
hb = K b = ( 0.0033 ) (Equation 5.1)
2g 2g

36
 Where is the bend angle in degrees and Kb* is the bend loss coefficient. These

equations are compared with Eq. 3.8 for a range of downstream Froude numbers in

Figure 5.1 The bend loss coefficients for r/Deq = 1 are also shown as points (diamonds)

for bend angles of 45o and 90o. It is apparent that the results of this study provide bend

loss coefficients that differ significantly from other commonly used equations. The flume

experiments demonstrated that head loss at abrupt bends in rectangular channels is

influenced by both flow conditions and geometry.

1.0
Fr= 0.3
0.9 F r= 0.2
Fr= 0.4
0.8
Fr= 0.5
0.7
Fr= 0.6
0.6

Kb = 0.5 Fr= 0.7
Kb 0.5 90
0.4

0.3
F r= 0.8

0.2

0.1 K b = 0.0033
0.0
30 40 50 60 70 80 90
Bend Angle (degrees)
E q11,F r= 0.2 E q11,F r= 0.3
E q11,F r= 0.4 E q11,F r= 0.5
E q11,F r= 0.6 E q11,F r= 0.7
E q11,F r= 0.8 E quation17
E quation18 Table5values forr/Deq= 1

Figure 5.1: Comparison of Abrupt Bend Loss Coefficients from Eq. 4.3 with
Values from Other Sources

37
 A method for determining the head loss for gradual bends was developed that

incorporated an adjustment factor . The factor was dependent on r/Deq where r is the

radius of curvature of the bend and Deq is the equivalent diameter of the culvert

(Deq=(4A/)1/2). The factor is equal to the average value of Kgb/Kgb,1 for the bend angles

of 22.5, 45 and 90 degrees where Kgb,1 is the bend loss coefficient for r/Deq =1. It was

assumed herein that Kgb,1 equals Kb for an abrupt bend as defined by Eq. 3.5 and Table

3.4. The head loss for a gradual bend is, therefore, given by the equation.

hb = K gb
Vds2
2g
[ ] V2 V2
= K b K gb / K gb ,1 ds = K b ds
2g 2g
Equation 5.2

Where Kgb is the gradual bend loss coefficient. The Shock waves are created for

supercritical flow and the flow can be analyze systematically. (2, 3) Moreover, if the

culvert flow is supercritical it is likely that it is under inlet control. Thus, the effects of the

bend on the supercritical flow profile will not affect the flow upstream from the culvert inlet

unless it ultimately creates a hydraulic jump within the culvert and, in turn, the

supercritical flow is flooded out.

This study produced results that can be used by practicing engineers to compute

head loses for abrupt and gradual culvert bends. Tables 2.4 and 3.1 and Fig. 3.9 are

repeated in the Design Tables and Charts section of APPENDIX A. Culvert bends will

likely become more commonplace in the face of continued restrictions on construction at

stream crossings. The bend-loss coefficients can be input into HEC-RAS via the Steady

Flow Data editor option as shown by these screen captures. The K Loss button allows

the user to input the bend loss coefficient when a culvert is modeled as an open channel

with a lid. (1)

38


Figure 5.2: Screen Capture of HEC-RAS Input Location for of Bend Loss Coefficient

It is recommended that the results of this study be used with a good degree of

engineering judgement. It is also recommended that experiments be undertaken to test

the validity of the factor developed herein to determine losses for gradual bends in

rectangular channels.

39
40
 CHAPTER 6 - REFERENCES

1. Gary W. Brunner, HEC-RAS River Analysis System Users Manual, Report No.
CPD-68, US Army Corps of Engineers, Hydrologic Engineering Center (HEC),
November 2002.

2. F. M. Henderson, Open Channel Flow, Prentice-Hall, Inc., 1966, pp 239-258.

3. V.T. Chow, Open-Channel Hydraulics, McGraw-Hill, 1958, pp 441-455.

4. J. M. Norman, Houghtalen, R.J. and Johnston, W. J., Hydraulic Design of

Highway Culverts, FHWA-NHI-01-020, HDS No. 5, 2001, pp 146-147.

5. Ray Linsley, Franzini, J.B., Freyberg, D.L. and Tchobanoglous, G., Water
Resources Engineering,, McGraw-Hill, Inc., 1992, pp 350-351.

41
42
APPENDIX A

43
Experimental Data

Table A1: Data for 30 Degree Experiments

Exp Angle Q yus = y2 yds = y16 z2 - z16 Vave hloss hf

No. (deg) (cfs) (ft) (ft) (ft) (fps) (ft) (ft)
1 2 3 4 5 6 7 8 9
1 30 0.714 0.783 0.776 0.0156 1.83 0.0220 0.0138
2 30 0.756 0.789 0.779 0.0156 1.93 0.0245 0.0153
3 30 0.398 0.496 0.495 0.0156 1.61 0.0168 0.0126
4 30 0.714 0.727 0.715 0.0156 1.98 0.0259 0.0165
5 30 0.299 0.396 0.395 0.0156 1.52 0.0168 0.0125
6 30 0.586 0.627 0.617 0.0156 1.89 0.0242 0.0158
7 30 0.756 0.732 0.719 0.0156 2.08 0.0265 0.0183
8 30 0.656 0.659 0.645 0.0156 2.01 0.0272 0.0177
9 30 0.477 0.526 0.517 0.0156 1.83 0.0232 0.0160
10 30 0.535 0.548 0.536 0.0156 1.97 0.0253 0.0183
11 30 0.714 0.659 0.640 0.0156 2.20 0.0305 0.0212
12 30 0.398 0.438 0.425 0.0156 1.84 0.0257 0.0177
13 30 0.586 0.564 0.547 0.0156 2.11 0.0287 0.0208
14 30 0.756 0.667 0.644 0.0156 2.31 0.0331 0.0232
15 30 0.656 0.604 0.584 0.0156 2.21 0.0308 0.0221
16 30 0.477 0.469 0.447 0.0156 2.08 0.0314 0.0220
17 30 0.586 0.527 0.505 0.0156 2.27 0.0310 0.0248
18 30 0.714 0.592 0.559 0.0156 2.48 0.0379 0.0283
19 30 0.756 0.612 0.575 0.0156 2.55 0.0403 0.0294
20 30 0.586 0.509 0.478 0.0156 2.38 0.0358 0.0277
21 30 0.656 0.549 0.509 0.0156 2.48 0.0414 0.0292
22 30 0.398 0.384 0.356 0.0156 2.15 0.0330 0.0261
23 30 0.299 0.306 0.280 0.0156 2.05 0.0303 0.0270
24 30 0.535 0.454 0.408 0.0156 2.48 0.0413 0.0322
25 30 0.756 0.562 0.497 0.0156 2.86 0.0495 0.0387
26 30 0.477 0.409 0.361 0.0156 2.48 0.0399 0.0339
27 30 0.398 0.362 0.317 0.0156 2.34 0.0380 0.0325
28 30 0.299 0.299 0.262 0.0156 2.14 0.0339 0.0303
29 30 0.586 0.473 0.409 0.0156 2.66 0.0476 0.0366
30 30 0.535 0.443 0.380 0.0156 2.60 0.0463 0.0361
31 30 0.477 0.405 0.347 0.0156 2.54 0.0426 0.0360
32 30 0.656 0.509 0.428 0.0156 2.80 0.0541 0.0393

44
Table A1: Data for 30 Degree Experiments (Continued)
2 2
Exp Fr,ds h*b=hb/yds Vds V ds/2g F r,ds Kbend yds/W
2
No. (fps) (ft) [hb/(V ds/2g)]
1 11 12 13 14 15 16 17
1 0.368 0.0106 1.84 0.0526 0.136 0.157 1.57
2 0.388 0.0119 1.94 0.0585 0.150 0.158 1.58
3 0.403 0.0085 1.61 0.0401 0.162 0.104 0.99
4 0.416 0.0131 2.00 0.0619 0.173 0.151 1.45
5 0.426 0.0108 1.52 0.0358 0.181 0.119 0.79
6 0.427 0.0135 1.90 0.0562 0.182 0.148 1.25
7 0.437 0.0115 2.10 0.0687 0.191 0.120 1.46
8 0.446 0.0148 2.03 0.0643 0.199 0.149 1.32
9 0.452 0.0139 1.84 0.0529 0.205 0.136 1.05
10 0.481 0.0130 2.00 0.0619 0.231 0.112 1.10
11 0.492 0.0147 2.23 0.0773 0.242 0.121 1.32
12 0.506 0.0189 1.87 0.0545 0.256 0.147 0.88
13 0.511 0.0145 2.15 0.0715 0.262 0.111 1.13
14 0.516 0.0154 2.35 0.0856 0.266 0.116 1.33
15 0.518 0.0149 2.25 0.0784 0.269 0.111 1.21
16 0.563 0.0211 2.13 0.0707 0.317 0.134 0.94
17 0.577 0.0123 2.32 0.0839 0.332 0.074 1.05
18 0.602 0.0173 2.56 0.1014 0.363 0.095 1.18
19 0.611 0.0189 2.63 0.1074 0.374 0.101 1.22
20 0.626 0.0170 2.46 0.0936 0.392 0.087 1.02
21 0.637 0.0239 2.58 0.1032 0.406 0.118 1.10
22 0.661 0.0193 2.24 0.0776 0.437 0.088 0.77
23 0.714 0.0115 2.14 0.0713 0.510 0.045 0.61
24 0.724 0.0224 2.62 0.1068 0.524 0.086 0.91
25 0.761 0.0217 3.04 0.1438 0.579 0.075 1.12
26 0.776 0.0165 2.64 0.1085 0.602 0.055 0.82
27 0.787 0.0173 2.51 0.0979 0.619 0.056 0.72
28 0.789 0.0138 2.29 0.0814 0.622 0.044 0.60
29 0.791 0.0269 2.87 0.1279 0.626 0.086 0.95
30 0.806 0.0269 2.82 0.1232 0.649 0.083 0.89
31 0.823 0.0190 2.75 0.1174 0.678 0.056 0.81
32 0.826 0.0344 3.07 0.1460 0.683 0.101 1.02

45
Table A2: Data for 45.2 Degree Experiments
Exp Angle Q yus = y2 yds = y16 z2 - z16 Vave hloss hf hb
No. (deg) (cfs) (ft) (ft) (ft) (fps) (ft) (ft) (ft)
1 2 3 4 5 6 7 8 9 10
33 45.2 0.514 0.847 0.820 -0.0130 1.23 0.0125 0.0061 0.00635
34 45.2 0.565 0.833 0.801 -0.0130 1.38 0.0167 0.0078 0.00892
35 45.2 0.514 0.766 0.733 -0.0130 1.37 0.0174 0.0078 0.00960
36 45.2 0.642 0.855 0.820 -0.0130 1.53 0.0189 0.0094 0.00951
37 45.2 0.693 0.859 0.819 -0.0130 1.65 0.0230 0.0110 0.01200
38 45.2 0.565 0.747 0.710 -0.0130 1.55 0.0202 0.0101 0.01008
39 45.2 0.514 0.686 0.646 -0.0130 1.54 0.0225 0.0103 0.01222
40 45.2 0.749 0.872 0.828 -0.0130 1.76 0.0260 0.0124 0.01357
41 45.2 0.693 0.809 0.765 -0.0130 1.76 0.0256 0.0127 0.01291
42 45.2 0.642 0.766 0.724 -0.0130 1.72 0.0238 0.0124 0.01141
43 45.2 0.565 0.675 0.628 -0.0130 1.73 0.0272 0.0132 0.01407
44 45.2 0.749 0.803 0.752 -0.0130 1.93 0.0304 0.0153 0.01515
45 45.2 0.514 0.626 0.579 -0.0130 1.71 0.0269 0.0131 0.01382
46 45.2 0.693 0.744 0.692 -0.0130 1.93 0.0306 0.0157 0.01487
47 45.2 0.642 0.702 0.651 -0.0130 1.90 0.0295 0.0155 0.01402
48 45.2 0.749 0.734 0.673 -0.0130 2.13 0.0357 0.0193 0.01645
49 45.2 0.693 0.678 0.612 -0.0130 2.15 0.0383 0.0203 0.01800
50 45.2 0.565 0.598 0.529 -0.0130 2.01 0.0406 0.0186 0.02197
51 45.2 0.642 0.642 0.573 -0.0130 2.11 0.0402 0.0200 0.02011
52 45.2 0.514 0.553 0.492 -0.0130 1.97 0.0339 0.0185 0.01540
53 45.2 0.749 0.669 0.592 -0.0130 2.38 0.0424 0.0250 0.01744
54 45.2 0.642 0.591 0.511 -0.0130 2.33 0.0423 0.0253 0.01694
55 45.2 0.565 0.549 0.466 -0.0130 2.23 0.0445 0.0240 0.02048
56 45.2 0.693 0.617 0.528 -0.0130 2.42 0.0474 0.0269 0.02046
57 45.2 0.514 0.512 0.411 -0.0130 2.23 0.0535 0.0250 0.02845
58 45.2 0.565 0.522 0.418 -0.0130 2.40 0.0503 0.0290 0.02132
59 45.2 0.642 0.559 0.451 -0.0130 2.54 0.0511 0.0313 0.01981
60 45.2 0.514 0.490 0.388 -0.0130 2.34 0.0484 0.0283 0.02005

46
Table A2: Data for 45.2 Degree Experiments (Continued)

2 2
Exp Fr,ds h*b=hb/yds Vds V ds/2g F r,ds Kbend yds/W
2
No. (fps) (ft) [hb/(V ds/2g)]
1 11 12 13 14 15 16 17
33 0.244 0.0077 1.25 0.0244 0.059 0.260 1.69
34 0.278 0.0111 1.41 0.0309 0.077 0.288 1.67
35 0.289 0.0131 1.40 0.0305 0.083 0.314 1.53
36 0.305 0.0116 1.57 0.0380 0.093 0.250 1.71
37 0.329 0.0147 1.69 0.0444 0.108 0.270 1.72
38 0.333 0.0142 1.59 0.0394 0.111 0.256 1.49
39 0.349 0.0189 1.59 0.0393 0.122 0.311 1.37
40 0.350 0.0164 1.81 0.0508 0.123 0.267 1.74
41 0.365 0.0169 1.81 0.0509 0.133 0.253 1.62
42 0.367 0.0158 1.77 0.0488 0.135 0.234 1.53
43 0.400 0.0224 1.80 0.0503 0.160 0.280 1.35
44 0.405 0.0201 1.99 0.0616 0.164 0.246 1.61
45 0.411 0.0239 1.77 0.0489 0.169 0.283 1.25
46 0.424 0.0215 2.00 0.0622 0.180 0.239 1.49
47 0.431 0.0215 1.97 0.0603 0.185 0.232 1.40
48 0.478 0.0244 2.23 0.0769 0.229 0.214 1.47
49 0.510 0.0294 2.26 0.0796 0.260 0.226 1.36
50 0.518 0.0415 2.14 0.0709 0.268 0.310 1.20
51 0.521 0.0351 2.24 0.0779 0.272 0.258 1.28
52 0.525 0.0313 2.09 0.0677 0.275 0.227 1.11
53 0.579 0.0295 2.53 0.0994 0.336 0.175 1.34
54 0.619 0.0331 2.51 0.0979 0.383 0.173 1.18
55 0.626 0.0439 2.43 0.0913 0.392 0.224 1.10
56 0.636 0.0387 2.62 0.1069 0.405 0.191 1.23
57 0.687 0.0692 2.50 0.0970 0.472 0.293 1.02
58 0.737 0.0510 2.70 0.1135 0.543 0.188 1.04
59 0.746 0.0439 2.85 0.1257 0.557 0.158 1.12
60 0.749 0.0517 2.65 0.1089 0.561 0.184 0.98

47
Table A3: Data for 58.5 Degree Experiments

Exp Angle Q yus = y2 yds = y16 z2 - z16 Vave hloss hf hb

No. (deg) (cfs) (ft) (ft) (ft) (fps) (ft) (ft) (ft)
1 2 3 4 5 6 7 8 9 10
61 58.5 0.493 0.753 0.723 -0.0052 1.34 0.0227 0.0075 0.01527
62 58.5 0.287 0.514 0.489 -0.0052 1.15 0.0179 0.0064 0.01155
63 58.5 0.537 0.764 0.728 -0.0052 1.44 0.0279 0.0087 0.01920
64 58.5 0.589 0.791 0.752 -0.0052 1.53 0.0303 0.0096 0.02069
65 58.5 0.493 0.700 0.663 -0.0052 1.45 0.0284 0.0090 0.01945
66 58.5 0.537 0.712 0.671 -0.0052 1.55 0.0315 0.0104 0.02117
67 58.5 0.691 0.836 0.791 -0.0052 1.70 0.0350 0.0117 0.02332
68 58.5 0.662 0.802 0.750 -0.0052 1.71 0.0409 0.0120 0.02892
69 58.5 0.589 0.739 0.694 -0.0052 1.64 0.0347 0.0114 0.02324
70 58.5 0.625 0.763 0.716 -0.0052 1.69 0.0363 0.0120 0.02435
71 58.5 0.287 0.454 0.424 -0.0052 1.31 0.0213 0.0089 0.01245
72 58.5 0.493 0.632 0.586 -0.0052 1.62 0.0348 0.0118 0.02306
73 58.5 0.691 0.787 0.733 -0.0052 1.82 0.0417 0.0137 0.02797
74 58.5 0.747 0.825 0.766 -0.0052 1.88 0.0458 0.0144 0.03141
75 58.5 0.537 0.650 0.595 -0.0052 1.73 0.0417 0.0133 0.02847
76 58.5 0.662 0.740 0.681 -0.0052 1.86 0.0450 0.0147 0.03026
77 58.5 0.625 0.710 0.650 -0.0052 1.84 0.0457 0.0146 0.03109
78 58.5 0.589 0.682 0.624 -0.0052 1.80 0.0439 0.0142 0.02970
79 58.5 0.691 0.725 0.653 -0.0052 2.00 0.0538 0.0172 0.03661
80 58.5 0.747 0.758 0.683 -0.0052 2.07 0.0560 0.0182 0.03782
81 58.5 0.493 0.575 0.514 -0.0052 1.81 0.0445 0.0154 0.02911
82 58.5 0.287 0.401 0.356 -0.0052 1.52 0.0314 0.0129 0.01851
83 58.5 0.662 0.683 0.606 -0.0052 2.05 0.0562 0.0185 0.03765
84 58.5 0.537 0.595 0.524 -0.0052 1.92 0.0513 0.0171 0.03413
85 58.5 0.625 0.654 0.578 -0.0052 2.03 0.0550 0.0184 0.03661
86 58.5 0.589 0.623 0.546 -0.0052 2.02 0.0552 0.0185 0.03662
87 58.5 0.691 0.673 0.580 -0.0052 2.20 0.0653 0.0216 0.04369
88 58.5 0.747 0.702 0.599 -0.0052 2.30 0.0717 0.0231 0.04856
89 58.5 0.493 0.525 0.446 -0.0052 2.03 0.0528 0.0203 0.03250
90 58.5 0.662 0.634 0.535 -0.0052 2.26 0.0666 0.0234 0.04316
91 58.5 0.625 0.604 0.507 -0.0052 2.25 0.0640 0.0236 0.04040
92 58.5 0.589 0.579 0.480 -0.0052 2.23 0.0646 0.0235 0.04110
93 58.5 0.537 0.544 0.451 -0.0052 2.16 0.0603 0.0228 0.03752
94 58.5 0.691 0.631 0.513 -0.0052 2.42 0.0747 0.0268 0.04790
95 58.5 0.747 0.655 0.525 -0.0052 2.53 0.0799 0.0292 0.05078
96 58.5 0.662 0.597 0.456 -0.0052 2.51 0.0814 0.0301 0.05125
97 58.5 0.493 0.493 0.371 -0.0052 2.28 0.0694 0.0271 0.04223
98 58.5 0.625 0.572 0.430 -0.0052 2.50 0.0798 0.0303 0.04941
99 58.5 0.691 0.614 0.458 -0.0052 2.58 0.0882 0.0314 0.05682
100 58.5 0.589 0.550 0.410 -0.0052 2.46 0.0779 0.0299 0.04795
101 58.5 0.537 0.519 0.384 -0.0052 2.38 0.0748 0.0290 0.04582
102 58.5 0.747 0.647 0.477 -0.0052 2.66 0.0953 0.0328 0.06256
103 58.5 0.493 0.490 0.357 -0.0052 2.33 0.0724 0.0285 0.04384
104 58.5 0.537 0.517 0.377 -0.0052 2.41 0.0757 0.0297 0.04604

48
Table A3: Data for 58.5 Degree Experiments (Continued)
2 2
Exp Fr,ds h*b=hb/yds Vds V ds/2g F r,ds Kbend yds/W
2
No. (fps) (ft) [hb/(V ds/2g)]
1 11 12 13 14 15 16 17
61 0.283 0.0211 1.36 0.0289 0.080 0.529 1.51
62 0.296 0.0236 1.18 0.0215 0.088 0.538 1.03
63 0.305 0.0264 1.48 0.0339 0.093 0.567 1.53
64 0.319 0.0275 1.57 0.0381 0.101 0.542 1.58
65 0.322 0.0293 1.49 0.0343 0.104 0.567 1.40
66 0.345 0.0316 1.60 0.0399 0.119 0.531 1.42
67 0.346 0.0295 1.75 0.0474 0.120 0.492 1.67
68 0.359 0.0386 1.77 0.0484 0.129 0.598 1.60
69 0.359 0.0335 1.70 0.0448 0.129 0.519 1.48
70 0.364 0.0340 1.75 0.0474 0.132 0.514 1.53
71 0.367 0.0294 1.36 0.0286 0.135 0.436 0.91
72 0.387 0.0394 1.68 0.0439 0.150 0.525 1.26
73 0.388 0.0382 1.88 0.0552 0.151 0.507 1.57
74 0.393 0.0410 1.95 0.0591 0.154 0.531 1.65
75 0.413 0.0479 1.81 0.0507 0.171 0.561 1.30
76 0.415 0.0444 1.94 0.0587 0.172 0.516 1.48
77 0.421 0.0478 1.92 0.0575 0.177 0.541 1.42
78 0.422 0.0476 1.89 0.0554 0.178 0.536 1.36
79 0.462 0.0561 2.12 0.0695 0.213 0.527 1.45
80 0.467 0.0554 2.19 0.0743 0.218 0.509 1.52
81 0.471 0.0567 1.92 0.0571 0.222 0.510 1.15
82 0.477 0.0520 1.62 0.0405 0.228 0.457 0.80
83 0.495 0.0622 2.18 0.0741 0.245 0.508 1.37
84 0.500 0.0652 2.05 0.0654 0.250 0.522 1.19
85 0.502 0.0634 2.16 0.0727 0.252 0.503 1.31
86 0.515 0.0671 2.16 0.0724 0.265 0.506 1.25
87 0.551 0.0754 2.38 0.0881 0.304 0.496 1.35
88 0.568 0.0811 2.50 0.0967 0.323 0.502 1.40
89 0.583 0.0729 2.21 0.0759 0.340 0.428 1.05
90 0.596 0.0807 2.48 0.0951 0.356 0.454 1.27
91 0.611 0.0797 2.47 0.0945 0.373 0.427 1.21
92 0.625 0.0857 2.46 0.0937 0.390 0.439 1.16
93 0.626 0.0832 2.38 0.0883 0.392 0.425 1.09
94 0.663 0.0934 2.69 0.1127 0.439 0.425 1.26
95 0.693 0.0968 2.85 0.1259 0.480 0.403 1.31
96 0.758 0.1125 2.90 0.1310 0.575 0.391 1.19
97 0.769 0.1139 2.66 0.1096 0.591 0.385 0.99
98 0.782 0.1150 2.91 0.1315 0.612 0.376 1.14
99 0.786 0.1241 3.02 0.1414 0.618 0.402 1.23
100 0.792 0.1170 2.88 0.1284 0.627 0.373 1.10
101 0.797 0.1194 2.80 0.1218 0.635 0.376 1.04
102 0.800 0.1312 3.13 0.1525 0.640 0.410 1.29
103 0.815 0.1229 2.76 0.1184 0.664 0.370 0.98
104 0.819 0.1222 2.85 0.1264 0.671 0.364 1.03

49
Table A4: Data for 76 Degree Experiments

Exp Angle Q yus = y2 yds = y16 z2 - z16 Vave hloss hf hb

No. (deg) (cfs) (ft) (ft) (ft) (fps) (ft) (ft) (ft)
1 2 3 4 5 6 7 8 9 10
105 76.2 0.228 0.581 0.582 0.0130 0.78 0.0120 0.0028 0.00922
106 76.2 0.228 0.507 0.504 0.0130 0.90 0.0159 0.0039 0.01191
107 76.2 0.228 0.426 0.413 0.0130 1.09 0.0249 0.0062 0.01862
108 76.2 0.228 0.370 0.350 0.0130 1.27 0.0302 0.0092 0.02104
109 76.2 0.228 0.324 0.288 0.0130 1.49 0.0408 0.0140 0.02688
110 76.2 0.364 0.759 0.760 0.0130 0.96 0.0120 0.0038 0.00823
111 76.2 0.364 0.700 0.694 0.0130 1.04 0.0187 0.0047 0.01405
112 76.2 0.364 0.640 0.632 0.0130 1.15 0.0205 0.0058 0.01470
113 76.2 0.364 0.581 0.566 0.0130 1.27 0.0267 0.0074 0.01928
114 76.2 0.364 0.521 0.499 0.0130 1.43 0.0323 0.0098 0.02242
115 76.2 0.364 0.468 0.426 0.0130 1.63 0.0472 0.0136 0.03360
116 76.2 0.364 0.426 0.360 0.0130 1.85 0.0608 0.0188 0.04205
117 76.2 0.364 0.401 0.299 0.0130 2.08 0.0741 0.0252 0.04889
118 76.2 0.479 0.807 0.798 0.0130 1.19 0.0215 0.0058 0.01569
119 76.2 0.479 0.750 0.736 0.0130 1.29 0.0260 0.0070 0.01907
120 76.2 0.479 0.689 0.668 0.0130 1.41 0.0321 0.0086 0.02347
121 76.2 0.479 0.629 0.600 0.0130 1.56 0.0384 0.0109 0.02754
122 76.2 0.479 0.572 0.530 0.0130 1.74 0.0478 0.0142 0.03366
123 76.2 0.479 0.527 0.463 0.0130 1.94 0.0618 0.0184 0.04345
124 76.2 0.479 0.489 0.392 0.0130 2.18 0.0768 0.0245 0.05232
125 76.2 0.311 0.645 0.630 0.0000 0.97 0.0143 0.0042 0.01012
126 76.2 0.436 0.845 0.825 0.0000 1.04 0.0192 0.0044 0.01480
127 76.2 0.629 0.890 0.860 0.0000 1.44 0.0278 0.0082 0.01960
128 76.2 0.436 0.670 0.640 0.0000 1.33 0.0275 0.0077 0.01973
129 76.2 0.749 0.860 0.810 0.0000 1.79 0.0440 0.0130 0.03105
130 76.2 0.629 0.705 0.645 0.0000 1.86 0.0504 0.0150 0.03537
131 76.2 0.749 0.740 0.660 0.0000 2.14 0.0636 0.0195 0.04410
132 76.2 0.436 0.505 0.440 0.0000 1.85 0.0503 0.0170 0.03328
133 76.2 0.311 0.410 0.355 0.0000 1.62 0.0431 0.0146 0.02846
134 76.2 0.629 0.600 0.505 0.0000 2.28 0.0669 0.0242 0.04269
135 76.2 0.749 0.650 0.480 0.0000 2.65 0.1012 0.0325 0.06870
136 76.2 0.629 0.575 0.405 0.0000 2.57 0.0945 0.0324 0.06207
137 76.2 0.311 0.365 0.260 0.0000 1.99 0.0613 0.0246 0.03678

50
Table A4: Data for 76 Degree Experiments (Continued)
2 2
Exp Fr,ds h*b=hb/yds Vds V ds/2g F r,ds Kbend yds/W
2
No. (fps) (ft) [hb/(V ds/2g)]
1 11 12 13 14 15 16 17
105 0.181 0.0158 0.78 0.0095 0.033 0.968 1.16
106 0.225 0.0236 0.90 0.0127 0.050 0.937 1.01
107 0.303 0.0451 1.10 0.0189 0.092 0.984 0.85
108 0.388 0.0601 1.30 0.0263 0.151 0.799 0.74
109 0.520 0.0933 1.58 0.0389 0.270 0.691 0.65
110 0.194 0.0108 0.96 0.0143 0.038 0.577 1.52
111 0.222 0.0202 1.05 0.0171 0.049 0.821 1.40
112 0.255 0.0233 1.15 0.0206 0.065 0.713 1.28
113 0.301 0.0341 1.29 0.0257 0.091 0.750 1.16
114 0.364 0.0449 1.46 0.0331 0.133 0.678 1.04
115 0.462 0.0789 1.71 0.0454 0.213 0.740 0.94
116 0.594 0.1168 2.02 0.0636 0.353 0.662 0.85
117 0.785 0.1635 2.44 0.0921 0.616 0.531 0.80
118 0.237 0.0197 1.20 0.0224 0.056 0.700 1.61
119 0.268 0.0259 1.30 0.0264 0.072 0.724 1.50
120 0.310 0.0351 1.44 0.0320 0.096 0.734 1.38
121 0.364 0.0459 1.60 0.0397 0.132 0.694 1.26
122 0.438 0.0635 1.81 0.0508 0.192 0.662 1.14
123 0.536 0.0938 2.07 0.0666 0.288 0.652 1.05
124 0.688 0.1335 2.45 0.0929 0.474 0.563 0.98
125 0.219 0.0161 0.99 0.0151 0.048 0.670 1.29
126 0.205 0.0179 1.06 0.0174 0.042 0.853 1.69
127 0.278 0.0228 1.46 0.0332 0.077 0.590 1.78
128 0.300 0.0308 1.36 0.0288 0.090 0.684 1.34
129 0.362 0.0383 1.85 0.0531 0.131 0.584 1.72
130 0.428 0.0548 1.95 0.0591 0.183 0.599 1.41
131 0.492 0.0668 2.27 0.0800 0.242 0.551 1.48
132 0.527 0.0756 1.98 0.0610 0.277 0.545 1.01
133 0.518 0.0802 1.75 0.0476 0.268 0.599 0.82
134 0.618 0.0845 2.49 0.0964 0.382 0.443 1.20
135 0.794 0.1431 3.12 0.1513 0.630 0.454 1.30
136 0.860 0.1533 3.11 0.1499 0.740 0.414 1.15
137 0.826 0.1415 2.39 0.0887 0.682 0.415 0.73

51
Table A5: Data for 90.5 Degree Experiments
Exp Angle Q yus = y2 yds = y16 z2 - z16 Vave hloss hf hb
No. (deg) (cfs) (ft) (ft) (ft) (fps) (ft) (ft) (ft)
1 2 3 4 5 6 7 8 9 10
138 90.5 0.278 0.608 0.572 -0.0182 0.94 0.0163 0.0040 0.01227
139 90.5 0.561 0.935 0.884 -0.0182 1.23 0.0303 0.0060 0.02436
140 90.5 0.473 0.830 0.785 -0.0182 1.17 0.0246 0.0056 0.01902
141 90.5 0.278 0.557 0.515 -0.0182 1.04 0.0214 0.0051 0.01627
142 90.5 0.380 0.680 0.634 -0.0182 1.16 0.0251 0.0058 0.01924
143 90.5 0.380 0.680 0.634 -0.0182 1.16 0.0251 0.0058 0.01924
144 90.5 0.561 0.866 0.808 -0.0182 1.34 0.0361 0.0072 0.02887
145 90.5 0.582 0.888 0.825 -0.0182 1.36 0.0408 0.0074 0.03337
146 90.5 0.473 0.771 0.717 -0.0182 1.27 0.0323 0.0068 0.02556
147 90.5 0.616 0.917 0.853 -0.0182 1.39 0.0416 0.0077 0.03396
148 90.5 0.380 0.627 0.575 -0.0182 1.26 0.0297 0.0072 0.02246
149 90.5 0.667 0.901 0.831 -0.0182 1.54 0.0460 0.0094 0.03658
150 90.5 0.667 0.901 0.831 -0.0182 1.54 0.0460 0.0094 0.03658
151 90.5 0.473 0.721 0.661 -0.0182 1.37 0.0369 0.0080 0.02886
152 90.5 0.616 0.858 0.786 -0.0182 1.50 0.0478 0.0091 0.03876
153 90.5 0.561 0.802 0.736 -0.0182 1.46 0.0423 0.0088 0.03348
154 90.5 0.582 0.821 0.751 -0.0182 1.48 0.0459 0.0090 0.03688
155 90.5 0.278 0.496 0.445 -0.0182 1.18 0.0282 0.0070 0.02125
156 90.5 0.473 0.680 0.614 -0.0182 1.46 0.0412 0.0094 0.03177
157 90.5 0.702 0.880 0.795 -0.0182 1.68 0.0581 0.0113 0.04676
158 90.5 0.380 0.587 0.525 -0.0182 1.37 0.0375 0.0087 0.02878
159 90.5 0.667 0.848 0.763 -0.0182 1.66 0.0579 0.0111 0.04680
160 90.5 0.561 0.753 0.677 -0.0182 1.57 0.0498 0.0104 0.03936
161 90.5 0.616 0.800 0.715 -0.0182 1.63 0.0577 0.0110 0.04671
162 90.5 0.582 0.770 0.686 -0.0182 1.60 0.0567 0.0108 0.04598
163 90.5 0.473 0.640 0.563 -0.0182 1.57 0.0490 0.0112 0.03787
164 90.5 0.702 0.827 0.725 -0.0182 1.81 0.0705 0.0135 0.05699
165 90.5 0.667 0.788 0.692 -0.0182 1.80 0.0648 0.0136 0.05120
166 90.5 0.380 0.540 0.473 -0.0182 1.50 0.0396 0.0109 0.02875
167 90.5 0.616 0.750 0.650 -0.0182 1.76 0.0681 0.0132 0.05487
168 90.5 0.561 0.700 0.610 -0.0182 1.71 0.0593 0.0128 0.04648
169 90.5 0.278 0.441 0.378 -0.0182 1.36 0.0360 0.0099 0.02617
170 90.5 0.582 0.711 0.612 -0.0182 1.76 0.0664 0.0135 0.05291
171 90.5 0.702 0.780 0.663 -0.0182 1.95 0.0796 0.0160 0.06364
172 90.5 0.473 0.598 0.503 -0.0182 1.72 0.0609 0.0138 0.04704
173 90.5 0.667 0.738 0.620 -0.0182 1.96 0.0788 0.0166 0.06221
174 90.5 0.561 0.648 0.540 -0.0182 1.89 0.0694 0.0162 0.05326
175 90.5 0.582 0.666 0.543 -0.0182 1.93 0.0810 0.0167 0.06430
176 90.5 0.380 0.494 0.402 -0.0182 1.70 0.0552 0.0147 0.04048
177 90.5 0.702 0.733 0.593 -0.0182 2.12 0.0919 0.0195 0.07234
178 90.5 0.278 0.399 0.313 -0.0182 1.56 0.0491 0.0141 0.03502
179 90.5 0.473 0.557 0.443 -0.0182 1.89 0.0699 0.0175 0.05241
180 90.5 0.667 0.697 0.551 -0.0182 2.14 0.0938 0.0203 0.07353
181 90.5 0.561 0.608 0.475 -0.0182 2.07 0.0811 0.0202 0.06091
182 90.5 0.616 0.651 0.502 -0.0182 2.14 0.0930 0.0210 0.07205
183 90.5 0.582 0.626 0.474 -0.0182 2.12 0.0939 0.0210 0.07297
184 90.5 0.702 0.701 0.533 -0.0182 2.28 0.1044 0.0231 0.08130
185 90.5 0.667 0.665 0.493 -0.0182 2.30 0.1028 0.0243 0.07848
186 90.5 0.616 0.632 0.456 -0.0182 2.27 0.1036 0.0241 0.07945
187 90.5 0.702 0.683 0.493 -0.0182 2.39 0.1115 0.0260 0.08559
188 90.5 0.582 0.609 0.435 -0.0182 2.23 0.1014 0.0238 0.07761
189 90.5 0.667 0.658 0.472 -0.0182 2.36 0.1078 0.0258 0.08200
190 90.5 0.702 0.679 0.482 -0.0182 2.42 0.1135 0.0268 0.08673

52
Table A5: Data for 90.5 Degree Experiments (Continued)
Exp Fr,ds h*b=hb/yds Vds V2ds/2g F2r,ds Kbend yds/W
No. (fps) (ft) [hb/(V2ds/2g)]
1 11 12 13 14 15 16 17
138 0.227 0.0214 0.97 0.0147 0.051 0.835 1.22
139 0.238 0.0276 1.27 0.0250 0.057 0.972 1.87
140 0.240 0.0242 1.21 0.0226 0.058 0.842 1.66
141 0.265 0.0316 1.08 0.0181 0.070 0.898 1.11
142 0.265 0.0304 1.20 0.0223 0.070 0.863 1.36
143 0.265 0.0304 1.20 0.0223 0.070 0.863 1.36
144 0.272 0.0357 1.39 0.0300 0.074 0.963 1.73
145 0.274 0.0405 1.41 0.0309 0.075 1.078 1.78
146 0.275 0.0357 1.32 0.0271 0.076 0.944 1.54
147 0.276 0.0398 1.44 0.0324 0.076 1.048 1.83
148 0.307 0.0391 1.32 0.0271 0.094 0.828 1.25
149 0.310 0.0440 1.60 0.0400 0.096 0.915 1.80
150 0.310 0.0440 1.60 0.0400 0.096 0.915 1.80
151 0.311 0.0437 1.43 0.0319 0.096 0.906 1.44
152 0.312 0.0493 1.57 0.0382 0.097 1.015 1.72
153 0.313 0.0455 1.53 0.0361 0.098 0.926 1.60
154 0.315 0.0491 1.55 0.0373 0.099 0.988 1.64
155 0.330 0.0478 1.25 0.0243 0.109 0.876 0.99
156 0.347 0.0517 1.54 0.0369 0.120 0.860 1.36
157 0.349 0.0588 1.77 0.0485 0.122 0.965 1.76
158 0.352 0.0548 1.45 0.0325 0.124 0.885 1.17
159 0.353 0.0613 1.75 0.0474 0.124 0.987 1.70
160 0.355 0.0581 1.66 0.0427 0.126 0.921 1.51
161 0.359 0.0653 1.72 0.0461 0.129 1.013 1.60
162 0.361 0.0670 1.70 0.0448 0.131 1.027 1.54
163 0.395 0.0673 1.68 0.0439 0.156 0.862 1.28
164 0.401 0.0786 1.94 0.0583 0.161 0.978 1.65
165 0.408 0.0740 1.93 0.0577 0.167 0.888 1.58
166 0.412 0.0608 1.61 0.0401 0.170 0.717 1.08
167 0.415 0.0844 1.90 0.0558 0.172 0.983 1.50
168 0.415 0.0762 1.84 0.0526 0.173 0.884 1.40
169 0.422 0.0693 1.47 0.0336 0.178 0.778 0.88
170 0.429 0.0865 1.90 0.0562 0.184 0.941 1.42
171 0.459 0.0960 2.12 0.0697 0.210 0.913 1.56
172 0.468 0.0936 1.88 0.0550 0.219 0.855 1.20
173 0.481 0.1004 2.15 0.0718 0.232 0.866 1.48
174 0.499 0.0987 2.08 0.0671 0.249 0.793 1.30
175 0.513 0.1185 2.15 0.0715 0.263 0.900 1.33
176 0.526 0.1007 1.89 0.0555 0.276 0.730 0.99
177 0.542 0.1220 2.37 0.0871 0.294 0.830 1.47
178 0.560 0.1119 1.78 0.0491 0.314 0.714 0.80
179 0.566 0.1184 2.14 0.0710 0.320 0.739 1.11
180 0.575 0.1335 2.42 0.0910 0.330 0.808 1.39
181 0.605 0.1283 2.36 0.0868 0.366 0.702 1.22
182 0.611 0.1436 2.46 0.0936 0.373 0.770 1.30
183 0.629 0.1540 2.46 0.0938 0.396 0.778 1.25
184 0.636 0.1526 2.64 0.1079 0.405 0.754 1.40
185 0.679 0.1592 2.71 0.1136 0.461 0.691 1.33
186 0.706 0.1743 2.70 0.1135 0.498 0.700 1.26
187 0.715 0.1737 2.85 0.1261 0.512 0.679 1.37
188 0.716 0.1785 2.68 0.1114 0.512 0.697 1.22
189 0.725 0.1738 2.83 0.1240 0.526 0.661 1.32
190 0.740 0.1800 2.91 0.1319 0.548 0.657 1.36

53
Design Tables and Charts

54
 Table A6: Loss Coefficients, Kb, for Abrupt Bends in Rectangular Channels (Report Table 3.4)

Abrupt Bend Angle, , in degrees

Fr
30 35 40 45 50 55 60 65 70 75 80 85 90
0.20 0.127 0.191 0.256 0.322 0.389 0.457 0.525 0.593 0.663 0.733 0.804 0.875 0.948
0.21 0.126 0.191 0.256 0.322 0.388 0.455 0.523 0.592 0.661 0.731 0.802 0.873 0.945
0.22 0.126 0.190 0.255 0.321 0.387 0.454 0.522 0.591 0.660 0.729 0.800 0.871 0.943
0.23 0.125 0.189 0.254 0.320 0.386 0.453 0.521 0.589 0.658 0.727 0.798 0.869 0.940
0.24 0.125 0.189 0.254 0.319 0.385 0.452 0.519 0.587 0.656 0.725 0.795 0.866 0.937
0.25 0.124 0.188 0.253 0.318 0.384 0.451 0.518 0.586 0.654 0.723 0.793 0.863 0.934
0.26 0.123 0.187 0.252 0.317 0.383 0.449 0.516 0.584 0.652 0.721 0.791 0.861 0.931
0.27 0.123 0.187 0.251 0.316 0.382 0.448 0.515 0.582 0.650 0.719 0.788 0.858 0.928
0.28 0.122 0.186 0.250 0.315 0.381 0.447 0.513 0.580 0.648 0.716 0.785 0.855 0.925
0.29 0.122 0.185 0.249 0.314 0.379 0.445 0.511 0.578 0.646 0.714 0.783 0.852 0.922
0.30 0.121 0.184 0.248 0.313 0.378 0.444 0.510 0.576 0.644 0.711 0.780 0.849 0.918
0.31 0.120 0.184 0.247 0.312 0.377 0.442 0.508 0.574 0.641 0.709 0.777 0.845 0.914
0.32 0.120 0.183 0.246 0.310 0.375 0.440 0.506 0.572 0.639 0.706 0.774 0.842 0.911
0.33 0.119 0.182 0.245 0.309 0.374 0.439 0.504 0.570 0.636 0.703 0.771 0.839 0.907
0.34 0.118 0.181 0.244 0.308 0.372 0.437 0.502 0.568 0.634 0.700 0.767 0.835 0.903
0.35 0.117 0.180 0.243 0.307 0.371 0.435 0.500 0.565 0.631 0.697 0.764 0.831 0.899
0.36 0.116 0.179 0.242 0.305 0.369 0.433 0.498 0.563 0.628 0.694 0.761 0.827 0.895
0.37 0.116 0.178 0.241 0.304 0.367 0.431 0.496 0.560 0.626 0.691 0.757 0.824 0.890
0.38 0.115 0.177 0.239 0.302 0.366 0.429 0.493 0.558 0.623 0.688 0.754 0.820 0.886

55
0.39 0.114 0.176 0.238 0.301 0.364 0.427 0.491 0.555 0.620 0.685 0.750 0.815 0.881
0.40 0.113 0.175 0.237 0.299 0.362 0.425 0.489 0.553 0.617 0.681 0.746 0.811 0.877
0.41 0.112 0.174 0.236 0.298 0.360 0.423 0.486 0.550 0.614 0.678 0.742 0.807 0.872
0.42 0.111 0.173 0.234 0.296 0.359 0.421 0.484 0.547 0.611 0.674 0.738 0.802 0.867
0.43 0.110 0.171 0.233 0.295 0.357 0.419 0.481 0.544 0.607 0.671 0.734 0.798 0.862
0.44 0.109 0.170 0.231 0.293 0.355 0.417 0.479 0.541 0.604 0.667 0.730 0.793 0.857
0.45 0.108 0.169 0.230 0.291 0.353 0.414 0.476 0.538 0.600 0.663 0.726 0.788 0.851
0.46 0.107 0.168 0.229 0.290 0.351 0.412 0.473 0.535 0.597 0.659 0.721 0.784 0.846
0.47 0.106 0.166 0.227 0.288 0.349 0.410 0.471 0.532 0.593 0.655 0.717 0.779 0.841
0.48 0.105 0.165 0.225 0.286 0.346 0.407 0.468 0.529 0.590 0.651 0.712 0.773 0.835
0.49 0.104 0.164 0.224 0.284 0.344 0.405 0.465 0.525 0.586 0.647 0.707 0.768 0.829
0.50 0.103 0.162 0.222 0.282 0.342 0.402 0.462 0.522 0.582 0.642 0.703 0.763 0.823
0.51 0.102 0.161 0.221 0.280 0.340 0.399 0.459 0.519 0.578 0.638 0.698 0.758 0.817
0.52 0.100 0.160 0.219 0.278 0.337 0.397 0.456 0.515 0.574 0.634 0.693 0.752 0.811
0.53 0.099 0.158 0.217 0.276 0.335 0.394 0.453 0.512 0.570 0.629 0.688 0.746 0.805
0.54 0.098 0.157 0.216 0.274 0.333 0.391 0.450 0.508 0.566 0.625 0.683 0.741 0.799
0.55 0.097 0.155 0.214 0.272 0.330 0.388 0.446 0.504 0.562 0.620 0.677 0.735 0.792
0.56 0.095 0.154 0.212 0.270 0.328 0.386 0.443 0.501 0.558 0.615 0.672 0.729 0.786
0.57 0.094 0.152 0.210 0.268 0.325 0.383 0.440 0.497 0.554 0.610 0.667 0.723 0.779
0.58 0.093 0.151 0.208 0.266 0.323 0.380 0.436 0.493 0.549 0.605 0.661 0.717 0.772
0.59 0.092 0.149 0.206 0.263 0.320 0.377 0.433 0.489 0.545 0.600 0.655 0.710 0.765

Vds2
hL = Kb
2g
 Table A6: (Cont.) Loss Coefficients, Kb, for Abrupt Bends in Rectangular Channels (Report Table 3.4)

Abrupt Bend Angle, , in degrees

Fr
30 35 40 45 50 55 60 65 70 75 80 85 90
0.59 0.092 0.149 0.206 0.263 0.320 0.377 0.433 0.489 0.545 0.600 0.655 0.710 0.765
0.60 0.090 0.147 0.204 0.261 0.317 0.374 0.429 0.485 0.540 0.595 0.650 0.704 0.758
0.61 0.089 0.146 0.202 0.259 0.315 0.370 0.426 0.481 0.535 0.590 0.644 0.698 0.751
0.62 0.087 0.144 0.200 0.256 0.312 0.367 0.422 0.477 0.531 0.585 0.638 0.691 0.744
0.63 0.086 0.142 0.198 0.254 0.309 0.364 0.418 0.472 0.526 0.579 0.632 0.684 0.736
0.64 0.085 0.141 0.196 0.252 0.306 0.361 0.415 0.468 0.521 0.574 0.626 0.678 0.729
0.65 0.083 0.139 0.194 0.249 0.303 0.357 0.411 0.464 0.516 0.568 0.620 0.671 0.721
0.66 0.082 0.137 0.192 0.247 0.300 0.354 0.407 0.459 0.511 0.562 0.613 0.664 0.713
0.67 0.080 0.135 0.190 0.244 0.297 0.350 0.403 0.455 0.506 0.557 0.607 0.656 0.706
0.68 0.079 0.133 0.188 0.241 0.294 0.347 0.399 0.450 0.501 0.551 0.600 0.649 0.698
0.69 0.077 0.132 0.185 0.239 0.291 0.343 0.395 0.445 0.496 0.545 0.594 0.642 0.689
0.70 0.075 0.130 0.183 0.236 0.288 0.340 0.391 0.441 0.490 0.539 0.587 0.634 0.681
0.71 0.074 0.128 0.181 0.233 0.285 0.336 0.386 0.436 0.485 0.533 0.580 0.627 0.673
0.72 0.072 0.126 0.179 0.231 0.282 0.332 0.382 0.431 0.479 0.527 0.573 0.619 0.664
0.73 0.071 0.124 0.176 0.228 0.279 0.329 0.378 0.426 0.474 0.520 0.566 0.612 0.656
0.74 0.069 0.122 0.174 0.225 0.275 0.325 0.373 0.421 0.468 0.514 0.559 0.604 0.647
0.75 0.067 0.120 0.171 0.222 0.272 0.321 0.369 0.416 0.462 0.508 0.552 0.596 0.638
0.76 0.065 0.118 0.169 0.219 0.269 0.317 0.365 0.411 0.457 0.501 0.545 0.588 0.629
0.77 0.064 0.116 0.166 0.216 0.265 0.313 0.360 0.406 0.451 0.495 0.537 0.579 0.620

56
0.78 0.062 0.113 0.164 0.213 0.262 0.309 0.355 0.401 0.445 0.488 0.530 0.571 0.611
0.79 0.060 0.111 0.161 0.210 0.258 0.305 0.351 0.395 0.439 0.481 0.522 0.563 0.602
0.80 0.058 0.109 0.159 0.207 0.255 0.301 0.346 0.390 0.433 0.474 0.515 0.554 0.592
0.81 0.057 0.107 0.156 0.204 0.251 0.297 0.341 0.384 0.426 0.467 0.507 0.546 0.583
0.82 0.055 0.105 0.154 0.201 0.247 0.292 0.336 0.379 0.420 0.460 0.499 0.537 0.573
0.83 0.053 0.102 0.151 0.198 0.244 0.288 0.331 0.373 0.414 0.453 0.491 0.528 0.563
0.84 0.051 0.100 0.148 0.195 0.240 0.284 0.326 0.368 0.408 0.446 0.483 0.519 0.554
0.85 0.049 0.098 0.145 0.191 0.236 0.279 0.321 0.362 0.401 0.439 0.475 0.510 0.544
0.86 0.047 0.096 0.143 0.188 0.232 0.275 0.316 0.356 0.394 0.431 0.467 0.501 0.533
0.87 0.046 0.094 0.141 0.186 0.230 0.272 0.313 0.353 0.390 0.427 0.462 0.495 0.527

Vds2
hL = Kb
2g
 1.0

0.9 Vds2
o
90 hL = Kb
0.8 2g
o
0.7
80

o
0.6 70

0.5 o

Kb
60

57
0.4
o
50
0.3
o
40
0.2
o
30
0.1

0.0
0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9

Frds= Vds/(gyds)1/2

Figure A.1: Kb versus Downstream Froude Number (Report Fig. 3.10)

 Table A7: Factor versus r/Deq for Gradual Bends (Report Table 7)

r/Deq = Kgb/Kgb,1
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
1 1.000 0.960 0.920 0.879 0.839 0.799 0.759 0.719 0.679 0.638
2 0.598 0.593 0.588 0.583 0.578 0.573 0.568 0.563 0.558 0.553
3 0.548 0.543 0.538 0.533 0.528 0.523 0.518 0.513 0.508 0.503
4 0.498 0.488 0.479 0.469 0.459 0.450 0.440 0.431 0.421 0.411
5 0.402 0.392 0.383 0.373 0.363 0.354 0.344 0.335 0.325 0.315
6 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306
7 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306
8 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306 0.306

58