Scribd Logo
Upload

Welcome to Scribd!

  • 66 views

    Isweek SprintIR CO2 Sensor

    Uploaded by

    industrial
    SprintIR is a high speed (20 Hz) CO2 sensor, ideally suited for applications which require capture of rapidly changing CO2 concentrations including metabolic assessment and analytical instrumentation.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Isweek SprintIR CO2 Sensor

    Uploaded by

    industrial
    66 views2 pages
    SprintIR is a high speed (20 Hz) CO2 sensor, ideally suited for applications which require capture of rapidly changing CO2 concentrations including metabolic assessment and analytical instrumentation.

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    SprintIR is a high speed (20 Hz) CO2 sensor, ideally suited for applications which require capture of rapidly changing CO2 concentrations including metabolic assessment and analytical instrumentation.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    66 views2 pages

    Isweek SprintIR CO2 Sensor

    Uploaded by

    industrial
    SprintIR is a high speed (20 Hz) CO2 sensor, ideally suited for applications which require capture of rapidly changing CO2 concentrations including metabolic assessment and analytical instrumentation.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    SprintIR

    High Speed Carbon Dioxide Sensor


    SprintIR is a high speed (20 Hz) CO2 sensor, ideally suited for applications which require
    capture of rapidly changing CO2 concentrations including metabolic assessment and analytical
    instrumentation.

    High speed sensing (20Hz)

    Measurement ranges from 0 to 100%

    3.3V supply

    Low power requirement 35mW

    Flow through adaptor (Optional) Standard With flow adapter

    SprintIR Sensor

    10000
    Instantaneous Concentration

    8000

    6000
    (ppm)

    4000

    2000

    0
    0 1 2 3 4
    Time (s)

    Specifications
    CO2 Measurement
    Sensing Method Non-dispersive infrared (NDIR) absorption
    Patented Gold-plated optics
    Patented Solid-state source and detector
    Sample Method Diffusion(Standard) / Flow through (with flow-through adapter)
    Measurement Range 0-5%, 0-20%, 0-60%, 0-100%
    Accuracy 70 ppm +/- 5% of reading1
    Measurement Noise <10% of reading with no digital filtering
    Non Linearity < 1% of FS
    Pressure Dependence 0.1% of reading per mbar in normal atmospheric conditions
    Operating Pressure Range 950 mbar to 10 bar2
    General Performance
    Warm-up Time < 1 minute
    Operating Conditions 0C to 50C (Standard)
    -25C to 55C (Extended range)
    0 to 95% RH, non-condensing
    Recommended Storage -30C to +70C
    Electrical/ Mechanical
    Power Input 3.2 to 5V. (3.3V recommended)
    Peak current 100mA
    Average Current <15mA
    Power Consumption 35 mW
    Output UART only
    Dimensions and Wiring Connections
    2x5 0.1 header. Pin 1 is identified on the dimensional drawing.

    Function Pin # Pin # Function


    0V 1 2 N/C
    +3.3V 3 4 0V
    Sensor Rx (in) 5 6 0V
    Sensor Tx (out) 7 8 Zero N
    N/C 9 10 Zero Air
    Pin 2 should not be connected. Pins 4 and 6 do not require connection and are internally
    connected to GND.

    The zeroing options are for hardware zeroing (both active low). These functions can also be
    implemented by sending a serial command (recommended).

    Typical connections for digital interface are GND, 3.3V, Rx and Tx. Note that the Vh for the serial
    Tx line will be 3V regardless of the supply voltage.
    Note 1: All measurements are at STP unless otherwise stated.
    Note 2: External Pressure calibration required.
    Note 3: User Configurable Filter Response.

    This documentation is provided on an as-is basis and no warranty as to its suitability or accuracy for any particular purpose is either made or
    implied. Gas Sensing Solutions Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this information. Your
    statutory rights are not affected. This information is not intended for use in any medical appliance, device or system in which the failure of the
    product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change
    without notice.

    You might also like