National Standard Plumbing Code

2003
NATIONALSTANDARD
PLUMBINGCODE
ILLUSTRATED
PHC:C: .
. .. (!)~c;) m
PLUMBING-HEAliNG-COOLING
CoNIRACToRSASSOCIAliON
Published By
PLUMBING-HEATING-COOLING CONTRACTORS-
NATIONAL ASSOCIATION
All inquiries or questions relating to interpretation should be forwarded to

Code Secretary
180 S. Washington St., P.O. Box 6808
Falls Church, VA 22046-1148
1-800-813-7061
~ 2003 Plumbing- Heating-Cooling Contractors-National Association

To order additional books call 1-800-533-7694
(if calling from New Jersey call 1-800-652-7422)
First Printing - January 2003
Second Printing - March 2004
Third Printing - January 2005
NATIONAL STANDARD
PLUMBING CODE
Title:
National Standard Plumbing Code
Scope:
The development of a recommended code of plumbing practice, design, and installation,

including the establishment of performance criteria predicated on the need for protection of
health and safety through proper design, installation, and maintenance of plumbing systems.
This scope excludes the development of specific standards related to the composition,
dimensions, and/or mechanical and physical properties of materials, fixtures, d~vices, and
equipment used or installed in plumbing systems.
Purpose:
To provide practices and performance criteria for the protection of health and safety through
proper design of plumbing systems.
Exceptions:
In case of practical difficulty, unnecessary hardship or new developments, exceptions to the

literal requirements may be granted by the authority havingjurisdiction to permit the use of
other devices or methods, but only when it is clearly evident that equivalent protection is
thereby secured.
11
FOREWORD
Since its founding as the National Association of Master Plumbers in 1883, the National Asso-
ciation of Plumbing- Heating-Cooling Contractors has maintained a serious interest in plumbing
standards, codes and good plumbing design practices.
The Association published the NAMP "Standard Plumbing Code" in 1933 and furnished revised
editions until 1942. NAPHCC participated in the development of special standards for war-time
plumbing and later was represented on the National Plumbing Code Coordinating Committee,
whose work ultimately resulted in the adoption of A40.8 as a standard or model plumbing code in
1955.
NAPHCC served as a sponsor in the early 1960's of the project which attempted to update the
1955 document. This project was operated through the procedures of the American National
Standards Institute. However, the A40.8 revision project was not completed because consensus
could not be achieved.
In order to provide local and state governments, code administrative bodies and industry with a
modem, updated code, NAPHCC published the "National Standard Plumbing Code," in 1971,
following the format and sequence ofthe A40.8 to provide for maximum convenience of users.
With the June 1973 revision, the American Society of Plumbing Engineers joined this effort by
co-sponsoring the National Standard Plumbing Code. ASPE maintained its co-sponsorship status
until September, 1980. Upon ASPE's withdrawal of co-sponsorship, the Code Committee compo-
sition was changed to include not only members of the contracting and engineering communities
but also members of the inspection community. Contractors, engineers and inspectors now
comprise the National Standard Plumbing Code Committee.
The National Standard Plumbing Code Committee has worked closely with the plumbing industry
to maintain a document of minimum requirements for plumbing systems that reflect current
practices, materials, and techniques, consistent with public health and safety.
However, the written requirements of a Code can sometimes be interpreted differently by differ-
ent individuals. For this reason, the NSPC Committee developed the NSPC Illustrated, which
includes explanatory comments and illustrations to demonstrate the intent of the various Code
Sections.
The Committee also realizes that despite the countless hours of preparation and review, perfection
may not have been achieved in this document. For this reason, please send any questions, com-
ments, suggestions, or problems to the Code Secretary, Plumbing-Heating-Cooling Contractors -
National Association, P.O. Box 6808, Falls Church, VA 22046-1148.
Comments on Code Text
The comments following the various Sections of the Code text are intended to explain the intent of
that Section of the Code. The comments themselves are not Code requirements but are intended
to supplement the Code and provide guidance toward its interpretation.
111
Figures and Figure Notes
The illustrations (figures) are intended to graphically demonstrate the intent or provide an example
of the referenced definition or Code Section. The illustrations are based only on the referenced
definition or Code Section and do not necessarily include all details of the complete installation,
such as pipe sizes, specific pipe fittings, required pipe supports, required cleanouts, and other
details that are not part of the definition or Code Section being illustrated. The illustrations must
not be used to justify work that does not comply with all requirements of the Code.
The illustrations are not intended to restrict installations to the arrangement shown. In many
cases, the illustrations show only one example or a typical example of an acceptable arrangement.
Any arrangement that meets the intent of the referenced Code Section is acceptable.
IV
Introductory Note
The material presented in this Code does not have legal standing unless it is adopted by
reference, or by inclusion, in an act of state, county, or municipal government. Therefore,
administration of the provisions ofthis Code must be preceded by suitable legislation at the
level of government where it is desired to use this Code.
In some places in this Code, reference is made to "Authority Having Jurisdiction." The
identity of an Authority Having Jurisdiction will be established by the act which gives legal
standing to the Code provisions.
Meetings for purposes of review and revision are scheduled each year with properpublic
notices.
Suggestions and requests for revisions can be made by any interested party and should
be submitted on the special fonTIsprovided by the Committee.
Personal appearance before the Committee for a hearing on any Code matter can be had
by interested parties after a request in writing.
In the course of revision, certain outdated sections have been deleted. In order to
maintain consistency and perpetuity of the numbering system, those deleted sections and
numbers have been removed from this printed text, or placed in reserve.
All changes from the previous edition of this Code are

marked by a vertical line in the margin.
v
2003 National Standard Plumbing Code Committee
J. Richard Wagner,PE,Chairman Thomas C. Pitcherello Robert Kordulak, NSPC Secretariat

The Poole & Kent Corporation NJ Department of Community Affairs The Arkord Company
4530 HollinsFerry Rd Codes Assistance Unit 206 1st Ave., # 603
Baltimore,MD21227-4670 101 S. Broad Street, PO Box 802 Belmar,NJ 07719-2006
Phone: (410)247-2200 Trenton, NJ 08625-0802 Phone: (732)681-5400
Fax: (410)247-2331 Phone: (609)984-7609 Fax: (732)681-5047
Dick - [email protected] Fax: (609)984-7717 bkord3 [email protected]
[email protected]
Charlie Chalk Willie C. Roberson
EBLEngineers,LLC Ronald W. Stiegler Executive Committee Liaison
8005HarfordRoad PhoenixPlumbers,Inc. W. C. Roberson Plumbing
Baltimore,MD21234-5701 5340EnterpriseSt 602 East Delavan Avenue
Phone:(410)668-8000 Eldersburg,MD 21784-9313 Buffalo,NY 14211
Fax: (410)668-8001 Phone:(410)781-3000 Phone: (716)892-5052
[email protected] Fax: (410)781-6826 Fax: (716)892-9442
[email protected] [email protected]
William Chamberlin
Chamberlin Plbg. & Htg Company, Inc. AlexTucciarone
P.O. Box390 Old Bridge PlumbingInspector
1274 Route 130 South 58 LearCt
Membersoftbe
Windsor, NJ 08561 EastBrunswick,NJ 08816-1853
Phone:(732)721-56002420 2002 National Standard
Phone: (609)448-1848
Fax: (609)448-8683 Fax: (732)607-7912 Plumbing Code Committee
[email protected] who contributed greatly to the
MichaelJ. Kastner publication ofthis Code.
Kastner Plumbing & Heating Jerry Van Pelt, CIPE
12630FriendshipRoad RPA/Mosher & Doran, Inc. J. Richard Wagner, PE, Chairman
West Friendship, MD 21794 175May Street, Suite 100
Phone:(30I)725-5000 Edison,NJ 08837
Fax: (410)442-7626 Phone: (732)225-9669
[email protected] Fax: (732)225-9656 Charlie Chalk
EBL Engjneers, LLC
Leon LaFreniere DaveViola
City of Manchester, Dept. of Buildings Plumbing Manufacturers Institute
One City Plaza 1340RemingtonRd., Suite A
Leon LaFreniere
Manchester, NH 0310 I Schaumburg,IL60173
Phone: (847)884-9764 City of Manhchester, NH
Phone:(603)624-6475
Fax: (603)624-6324 Fax: (847)884-9775
Frank R.Maddalon RichardD. Wagner,PE

F. R. Maddalon Plumbing& Heating Kruse Associates, P.c.
1550Sylvan Ave 130Central Avenue
Hamilton,NJ 08610-4461 JerseyCity,NJ 07306
Phone: (609)587-8317 Phone: (201)798-5200
Fax: (609)587-9848 Fax: (201)798-3430
Inc.
VI
","c,,' "; " ' "',: ,': ',,: ' . ~,,':' ',' , ,:" ,
INTRODUCTORY NOTE v
ADMINISTRATION. ...... ...... 1
BASIC PRINCIPLES 9
CHAPTER1 -Definitions ... 13
CHAPTER2 -General Regulations 65
CHAPTER3 -Materials 83
CHAPTER4 -Joints andConnections oooo.oo.oo oo 107
CHAPTER 5 -Traps, Cleanouts and Backwater Valves ..oo ..oooooooo... ..oo oooooooo 131
CHAPTER 6 -Interceptors ...... 147
CHAPTER7 -Plumbing Fixtures,FixtureFittingsandPlumbingAppliances 'OOOO""""""'" 157
CHAPTER8 -Hangers andSupports 189
CHAPTER9 -Indirect WastePipingand SpecialWastes oo OOOOOO"'OOOOOO'OOOO'"''OO''''''' 193
CHAPTER10 -Water SupplyandDistribution oo..oo.oooooo... 205
CHAPTER11 -Sanitary DrainageSystems 247
CHAPTER 12 -Vents andVenting oooo...oooooo..oo.oo oooo oooo... .oooo...oo.oo.. '''OOOO'''''OO'''''''''''''' 269
CHAPTER13 -Storm WaterDrainage oooooo... .oooooo ..oooo.. OO"OO"'"'''''''''''''''''''' 307
CHAPTER 14 -Special RequirementsforHealthCareFacilities 319
CHAPTER 15 -Tests and Maintenance.. oooo...oo oo.oo..oooo ...oo... 325
CHAPTER16 -Regulations GoverningIndividualSewageDisposal
SystemsforHomesandOtherEstablishmentsWhere
PublicSewageSystemsAreNotAvailable oooooo...oo oooo oo 329
CHAPTER 17 -Potable WaterSupplySystems 345
CHAPTER 18 -Mobile Home&TravelTrailer
ParkPlumbingStandards 353
APPENDIX A -Sizing StormDrainageSystems 363
APPENDIX B -Sizing theBuildingWaterSupplySystem 369
APPENDIX C -Conversions: CustomaryUnitsto Metric oooo...oo.oo...oooo oo.oooooo.oooooo 403
APPENDIX D -Determining theMinimumNumberofRequired
Plumbing Fixtures 405
APPENDIX E -Special DesignPlumbingSystems 409
APPENDIX F -Requirements oftheAuthorityHavingJurisdiction 411
APPENDIX G -Graywater RecyclingSystems 413
APPENDIX H -Installation ofMedicalGasandVacuumPipingSystems 417
APPENDIX I -Fixture UnitValueCurvesfor WaterClosets """"'''''''''OO''''OOOO'''''''OO'''' 419
APPENDIX J -Acceptable SizingCriteria 423
APPENDIX K -Flow in SlopingDrains 425
INDEX -Alphabetical Index 427
VII
In memory of, and dedicated to the lives of,
our dear friends, colleagues, and long-standing leaders,
Patrick J. Higgins
Tom Konen
Administration
ADM 1.1 TITLE
The regulations contained in the following chapters and sections shall be known as the "National Standard
Plumbing Code" and may be cited as such, and hereinafter referred to as "this Code".
ADM 1.2 SCOPE

The provisions of this Code shall apply to every installation, including the erection, installation, alteration, reloca-
tion, repair, replacement, addition to, use or maintenance of the plumbing system as defined within this Code.
ADM 1.3 PURPOSE

This Code establishes the minimum requirements and standards pertaining to the design, installation, use and
maintenance of the plumbing system as defined within this Code.
ADM 1.4 APPLICABILITY
1.4.1 Addition or Repair

Additions, alterations or repairs in compliance to this Code may be made to any existing plumbing system
without requiring the existing installation to comply with all the requirements of this Code. Additions, alterations or
repairs shall not cause an existing system to become unsafe, insanitary or overloaded.
1.4.2 Existing Plumbing Installation

Plumbing systems which were lawfully installed prior to the adoption of this Code may continue their use,
maintenance or repairs, provided the maintenance or repair is in accordance with the original design, location, and
no hazard has been created to life, health or property by such plumbing system.
1.4.3 Existing Use

The lawful use of any plumbing installation, appliances, fixtures, fittings and appurtenances may have their use
continued, provided no hazards to life, health or property have been created by their continued use.
1.4.4 Maintenance and Repairs

The maintenance of all plumbing systems, materials, appurtenances, devices or safeguards, both existing and
new, shall be maintained in a safe and proper condition. The owner, or his designated agent, shall be responsible
for the maintenance of the plumbing system.
Minor repairs to or replacement of any existing systems are permitted, provided they are made in the same
manner and arrangement as the original installation and are approved.
1.4.5 Change of Building Use

The plumbing systems of any building or structure, which is proposed for a change in use or occupancy, shall
comply to all the requirements of this Code for the new use or occupancy.
1.4.6 Moved Buildings or Structures

The plumbing system in any building or structure to be moved into this jurisdiction shall comply with the provi-
sions of this Code for new construction.
2003 National Standard PUl11hingCode-Illustrated 1

1.4.7 Special Historic Buildings
The provisions of this Code relating to the additions, alterations, repair, replacement or restoration of those
structures designated as historic buildings shall not be mandatory when such work is deemed to be safe and in the
public interest of health, safety and welfare by the Authority Having Jurisdiction.
1.4.8 Appendices
The provisions in the appendices are intended to supplement the requir~ments and are considered a part of this
Code.
ADM 1.5 APPROVALS
1.5.1 Alternates
The provisions cited in this Code are not intended to prevent the use of any material or method of installation
when it is determined to meet the intent of this Code and approved by the Authority Having Jurisdiction
1.5.2 Authority Having Jurisdiction

The Authority Having Jurisdiction may approve any such alternate material or method of installation not ex-
pressly conforming to the requirements of this Code, provided it finds the proposed material or method of installa-
tion is at least the equivalent of that required in the Code or that the alternate material or method of installation
conforms to other nationally accepted plumbing standards. A record of such approval shall be kept and shall be
available to the public.
1.5.3 Tests Required

The Authority Having Jurisdiction shall require sufficient evidence to substantiate any claims made regarding the
equivalency of any proposed alternate material or method of installation. When the Authority Having Jurisdiction
determines that there is insufficient evidence to substantiate the claims, it may require tests to substantiate the
claims be made by an approved testing agency at the expense of the applicant.
1.5.4 Test Procedure

The Authority Having Jurisdiction shall require all tests be made in accordance with approved standards; but, in
the absence of such standards, the Authority Having Jurisdiction shall specify the test procedure.
1.5.5 Retesting
The Authority Having Jurisdiction may require any tests to be repeated if, at any time, there is reason to believe
that any material or method of installation no longer conforms to the requirements on which the original approval
was based.
ADM 1.6 ORGANIZATION AND ENFORCEMENT
1.6.1 Authority Having Jurisdiction

The Authority Having Jurisdiction shall be the individual official,board, department or agency duly appointed by
the jurisdiction as having the authority to administer and enforce the provisions of this Code as adopted or
amended.
1.6.2 Deputies
In accordance with the procedures set forth by the jurisdictional authority, the Authority Having Jurisdiction may
appoint such assistants, deputies, inspectors or other designated employees to carry out the administration and
enforcement of this Code.
2 2003 National Standard Pumbing Code-Illustrated

1.6.3 Right of Entry
When inspections are required to enforce the provisions of this Code, or there is reasonable cause to believe
there exists in any building, structure or premises, any condition or violation of this Code causing the building,
structure or premises to be unsafe, insanitary, dangerous or hazardous, the Authority Having Jurisdiction or its
designated representative may enter such building, structure or premises at reasonable times to inspect or perform
the duties imposed by this Code. When the building, structure or premises are occupied, proper credentials shall be
presented to the occupant when entry is required. In the event the building, structure or premises is unoccupied,
and entry is required, a reasonable effort shall be made to locate the owner or his agent in charge of such building,
structure or premises. In the event the occupant or owner of such building, structure or premises refuses entry, the
Authority Having Jurisdiction shall have recourse to the remedies provided by law to gain entry.
1.6.4 Stop Work Order

Upon notice from the Authority Having Jurisdiction, work being done on any building, structure or premises
contrary to the provisions of this Code, or in an unsafe and dangerous manner, shall be stopped immediately. The
stop work notice shall be in writing, served on the owner of the property, or his agent, or to the person doing such
work. It shall state the conditions under which the Authority Having Jurisdiction may grant authorization to
proceed with the work.
1.6.5 Authority to Condemn

When the Authority Having Jurisdiction deten11ines that any plumbing system or portion thereof, which is
regulated by this Code, has become insanitary or hazardous to life, health or property, it shall order in writing that
such plumbing system or portion thereof be repaired, replaced or removed so as to be in code compliance. The
written order shall fix a reasonable time limit for the work to be brought into code compliance, and no person shall
use the condemned plumbing system until such work is complete and approved by the Authority Having Jurisdic-
tion.
1.6.6 Authority to Abate

Any plumbing system, or portion thereof, which is found to be insanitary or constitute a hazard to life, health or
property is hereby declared to be a nuisance. Where a nuisance exists, the Authority Having Jurisdiction shall
require the nuisance to be abated and shall seek such abatement in the manner prescribed by law.
1.6.7 Liability
The Authority Having Jurisdiction, or any individual duly appointed or authorized by the Authority Having
Jurisdiction to enforce this Code, acting in good faith and without malice, shall not thereby be rendered personally
liable for any damage that may occur to persons or property as a result of any act, or by reason of any act or
omission in the lawful discharge of his duties. Should a suit be brought against the Authority Having Jurisdiction or
duly appointed representative because of such act or omission, it shall be defended by legal counsel provided by
this jurisdiction until final termination of the proceedings.
1.6.8 Work Prior to Permit

Where work for which a permit is required by this Code is started prior to obtaining the prescribed permit, the
applicant shall pay a double fee. In the event of an emergency where it is absolutely necessary to perform the
plumbing work immediately, such as nights, weekends or holidays, said fee shall not be doubled if a permit is
secured at the earliest possible time after the emergency plumbing work has been performed.
ADM 1.7 VIOLATIONS AND PENALTIES

1.7.1 Violations
It shall be unlawful for any individual, partnership, firm or corporation to, or cause to, install, construct, erect,
alter, repair, improve, convert, move, use or maintain any plumbing system in violation of this Code.
2003 National Standard Pumbing Code-Illustrated 3

1.7.2 Penalties
Any individual, partnership, firm or corporation who shall violate or fail to comply with any of the requirements
of this Code shall be deemed guilty of a , and if convicted, shall be punishable by a fine or imprisonment
or both as established by this jurisdiction. Each day during which a violation occurs or continues, shall constitute a
separate offense.
ADM 1.8 PERMITS
1.8.1 Permits Required

It shall be unlawful for any individual, partnership, firm or corporation to commence, or cause to commence, any
installation, alteration, repair, replacement, conversion or addition to any plumbing system, or part thereof, regulated
by this Code, except as permitted in Section 1.8.2, without first obtaining a plumbing permit for each separate
building or structure, on forms prepared and provided by the Authority Having Jurisdiction.
1.8.2 Permits Not Required for the Following

a. The stopping of leaks in drains, soil, waste or vent pipes. However, should the defect necessitate removal and
replacement with new material, it shall constitute new work and a permit shall be obtained and inspection made as
required in this Code.
b. The clearing of stoppages.
c. The repairing of leaks in valves or fixtures.
d. The removing and reinstallation of a water closet for a cleanout opening provided the reinstallation does not
require replacement or rearrangement of valves, pipes or new fixtures.
Exemptions from obtaining a permit required by this Code shall not be construed as to authorize any work to be
performed in violation of this Code.
ADM 1.9 PROCESS FOR OBTAINING PERMITS
1.9.1 Application
Applications for a permit shall be made in writing by the person, or his agent, proposing to do such work covered
by the permit. The applicant shall file such application in writing on a form prepared and provided by the Authority
Having Jurisdiction. Every such permit shall:
a. Describe in detail the work to be done for which the permit was obtained.
b. Describe in detail the parcel of land on which the proposed work is to be done by legal description, street
address or other means to definitely locate the site or building where the work is to be performed.
c. List the type of occupancy or use.
d. Provide plans, drawings, diagrams, calculations or other data as required by Section 1.9.2.
e. Be signed by the person or agent making application.
f. Provide any other information the Authority Having Jurisdiction may require.
1.9.2 Plans
Two or more sets of plans shall be submitted with each permit application. The plans shall contain all the
engineering calculations, drawings, diagrams and other data as required for approval. The Authority Having
Jurisdiction may also require that the plans, drawings, diagrams and calculations be designed by an engineer and/or
architect licensed by the state in which the work is to be performed.
Except that the Authority Having Jurisdiction may waive the submission of plans and other data, provided it is
determined that the nature of the work covered by the permit does not require plan review to obtain code compli-
ance.
4 2003 National Standard Pumbing Code-1I/ustrated

1.9.3 Specifications
All specifications required to be on the plans shall be drawn to scale and sufficiently clear to indicate the nature,
location and extent ofthe proposed work so as to show how it will conform to the requirements of this Code.
1.9.4 Permit Issuance

If, after reviewing the plans and specifications, the Authority Having Jurisdiction finds that they are complete
and conform to the requirements of this Code, it shall authorize a permit to be issued upon payment of all the fees
specified in Section 1.10.1.
1.9.5 Approved Plans

When the Authority Having Jurisdiction issues a permit and plans were required, it shall endorse, either in
writing or stamp the plans "APPROVED", and all work shall be done in accordance with the plans without
deviation.
1.9.6 Plans Retention

The Authority Having Jurisdiction shall retain one set of approved plans until final approval of the work con-
tained therein. One set of approved plans shall be returned to the applicant and this set of approved plans shall be
kept on the job site at all times until final approval of the work contained therein.
1.9.7 Permit Validity

The issuance of a permit by the Authority Having Jurisdiction is not and shall not be construed to be authoriza-
tion or approval of any violation of the requirements of this Code. Any presumption of a permit to be authorization
to violate or cancel any provisions of this Code shall be invalid. The issuance of a permit based on plans submitted
shall not prevent the Authority Having Jurisdiction from requiring the correction of any errors in the plans or
preventing the progress of the construction when it is in violation of any provision of this Code.
1.9.8 Permit Expiration

Every permit issued by the Authority Having Jurisdiction, in accordance with the provisions of this Code, shall
expire by limitation and become null and void when such work authorized by the permit has not commenced within
days from the date of issuance or if such work is suspended or abandoned for a period of - days after com-
mencement of such work. In order for such work to recommence, a new permit shall be obtained and a fee of
percent of the original permit fee shall be charged, provided no changes have been made or will be made to the
original plans as submitted. The Authority Having Jurisdiction may grant an extension to any permit provided the
request is in writing by the permittee stating the reason or circumstances which prevented him from completing
such work as required by this Code.
1.9.9 Revocation or Suspension

At any time, the Authority Having Jurisdiction may suspend or revoke a permit issued in error or on the basis of
incorrect information submitted or in violation of any section of this Code. The suspension or revocation of such
permit shall be in written form by the Authority Having Jurisdiction stating the reason or purpose of such suspen-
sion or revocation.
ADM 1.10 PERMITS

1.10.1 Fees Schedule
The permit fees for all plumbing work shall be set forth by the Authority Having Jurisdiction of the jurisdiction
having authority.

1.10.2 Plan Review Fees
Whenplansare reviewedas a requirementpriorto issuanceof a permit,the fee shallbe equalto - percent
of the total permit fee as set forth in Section I. 10.I.
1.10.3 Plan Review Expiration

Permit application and plan review for which no permit is issued shall expire by limitation within - days
following the date of application. All plan review fees shall be forfeited and the plans may be destroyed by the
Authority Having Jurisdiction or returned to the applicant.
1.10.4 Work Without a Permit

When any plumbing work is commenced without first obtaining a permit from the Authority Having Jurisdiction,
an investigation of such work shall be made before a permit may be issued. The investigation fee shall be collected
whether or not a permit is then or subsequently issued. Any investigation fee shall equal the amount of the permit
fee, if a permit were to be issued in accordance with this Code. If the investigation fee is collected, it shall not
exempt any person from compliance or penalties set forth in this Code.
1.10.5 Refunding of Fees

Any fee collected by the Authority Having Jurisdiction, which was erroneously paid or collected, may be
refunded, provided not more than - percent of the fee payment shall be refunded when no work has been
done. Any request for the refunding of any fee shall be in writing by the applicant no later than - days after the
date of fee payment.
ADM 1.11 INSPECTIONS
1.11.1 Required Inspections

All new plumbing systems, and parts of existing systems which require a permit, shall be tested and inspected by
the Authority Having Jurisdiction prior to being covered or concealed. Where any such work has been covered or
concealed, the Authority Having Jurisdiction shall require such work exposed for inspection and testing. All
equipment, material and labor required for testing the plumbing system shall be furnished by the permittee. The
Authority Having Jurisdiction shall not be liable for any expense incurred by the removal or replacement of materi-
als required to permit inspection or testing. Such expense is the responsibility of the permittee. Upon completion of
the rough plumbing installation, prior to covering or concealing any such work, the Authority Having Jurisdiction
shall inspect the work and any such test, as prescribed hereinafter, to disclose any leaks or defects. After comple-
tion of the plumbing system and the plumbing fixtures are set and their traps filled with water, a final inspection
shall be conducted as required by this Code. Additional inspections may be required when alternate materials or
methods of installation are approved by the Authority Having Jurisdiction.
1.11.2 Exception:
For moved-in or relocated structures, minor installations and repairs, the Authority Having Jurisdiction may
make other such inspections or tests as necessary to assure that the work has been performed and is safe for use
in accordance with the intent of this Code.
1.11.3 Use of Existing Plumbing

The operation of any plumbing installation to replace existing systems or fixtures serving an occupied portion of
any building or structure shall not be considered by the requirements of this Code to prohibit such operation,
provided a request for inspection has been made to the Authority Having Jurisdiction within 48 hours of such work
and before any such work is covered or concealed.
6 20()3 National Standard Pumbing Code-Illustrated

1.11.4 System Testing
All new plumbing systems and parts of existing systems shall be tested and approved as required elsewhere in
this Code.
1.11.5 Requests for Inspection

The Authority Having Jurisdiction shall be notified by the person doing the work, authorized by the permit, that
such work is subjected to the required tests and is ready for inspection. The method of request, whether in writing
or by telephone, shall be established by the Authority Having Jurisdiction.
It shall be the duty ofthe permittee doing the work authorized by a permit to provide reasonable access and
means for accomplishing proper inspections.
1.11.6 Other Inspections

The Authority Having Jurisdiction may require other inspections, in addition to those required by this Code, of
any plumbing work in order to ascertain compliance with the requirements of this Code.
1.11.7 Reinspection Fees

The assessment of a reinspection fee may be required for any ofthe following:
a. For any portion of work not completed for which inspection was requested.
b. For any required corrections which have not been completed and for which reinspection was requested.
c. For not having the approved plans on site and readily available to the inspector.
d. Failure to provide access for inspection on the date inspection was requested.
e. Deviation from the approved plans which would require reapproval of the Authority Having Jurisdiction.
f. Failure to provide correct address.
This provision is intended to control the practice of calling for inspections prior to having work ready for inspec-
tion and not for the first time job rejection for not complying with the installation requirements.
Upon the assessment of a reinspection fee, the applicant shall pay the reinspection fee in accordance with
Section 1.10.1 and no additional inspections shall be perfon11ed until all fees have been paid.
ADM 1.12 FINAL CONNECTIONS
1.12.1 Energy or Fuel

It shall be unlawful for any person to make, or cause to make, any connection to any source of energy or fuel to
any plumbing system or equipment regulated by this Code prior to the approval of the Authority Having Jurisdic-
tion.
1.12.2 Water and Sewer

It shall be unlawful for any person to make, or cause to make, any connection to any water supply or sewer
system to any plumbing system or equipment regulated by this Code prior to the approval of the Authority Having
Jurisdiction.
1.12.3 Temporary Connection

By authorization ofthe Authority Having Jurisdiction, a temporary connection may be made to any plumbing
equipment to a source of energy or fuel for testing purposes only.
ADM 1.13 UNCONSTITUTIONALITY
Should any chapter, section, subsection, sentence, clause or phrase of this Code be held for any reason as
unconstitutional, such decision shall not affect the validity of the remaining chapters, sections, subsections, sen-
tences, clause or phrases of this Code.
2003 National Standard Pumbing Code-fIIustrated 7

Blank Page

,; '~C~':{'i;",,', '. ' . i',".
"~;;;
~:>B~~l~<J!rln
.;',',;/
ClpIes
::,': ,"
This Code is founded upon certain basic principles of environmental sanitation and safety through properly
designed, acceptably installed, and adequately maintained plumbing systems. Some of the details of plumbing
construction may vary but the basic sanitary and safety principles desirable and necessary to protect the health of
the people are the same everywhere.
The establishment of trade jurisdictional areas is not within the scope of this Code, This inclusion of material,
even though indicated as approved for purposes of this Code, does not infer unqualified endorsement as to its
selection or serviceability in any or every installation.
As interpretations may be required, and as unforeseen situations arise which are not specifically covered in this
Code, the twenty-two principles which follow shall be used to define the intent.
Principle No. I-ALL OCCUPIED PREMISES SHALL HAVE POTABLE WATER

All premises intended for human habitation, occupancy, or use shall be provided with a supply of potable water.
Such a water supply shall not be connected with unsafe water sources, nor shall it be subject to the hazards of
backflow.
PrincipleNo.2-ADEQUATE WATER REQUIRED

Plumbing fixtures, devices, and appurtenances shall be supplied with water in sufficient volume and at pressures
adequate to enable them to function properly and without undue noise under normal conditions of use.
PrincipleNo.3-HOT WATER REQUIRED

Hot water shall be supplied to all plumbing fixtures which normally need or require hot water for their proper use
and function.
PrincipleNo.4-WATER CONSERVATION
Plumbing shall be designed and adjusted to use the minimum quantity of water consistent with proper performance
and cleaning.
PrincipleNo.5-SAFETY DEVICES
Devices for heating and storing water shall be so designed and installed as to guard against dangers from explosion
or overheating.
Principle No.6-USE PUBLIC SEWER WHERE AVAILABLE

Every building with installed plumbing fixtures and intended for human habitation, occupancy, or use, and located
on premises where a public sewer is on or passes said premises within a reasonable distance, shall be connected to
the sewer.
Principle No.7-REQUIREDPLUMBING FIXTURES

Each family dwelling unit shall have at least one water closet, one lavatory, one kitchen-type sink, and one bathtub
or shower to meet the basic requirements of sanitation and personal hygiene.
All other structures for human habitation shall be equipped with sufficient sanitary facilities. Plumbing fixtures shall
be made of durable, smooth, non-absorbent and corrosion resistant material and shall be free from concealed
fouling surfaces.

Principle No.8-DRAINAGE SYSTEM
The drainage system shall be designed, constructed, and maintained to guard against fouling, deposit of solids and
clogging, and with adequate cleanouts so arranged that the pipes may be readily cleaned.
Principle No. 9-DURABLE MATERIALS AND GOOD WORKMANSHIP

The piping ofthe plumbing system shall be of durable material, free from defective workmanship and so designed
and constructed as to give satisfactory service for its reasonable expected life.
PrincipleNo.10-FIXTURE TRAPS
Each fixture directly connected to the drainage system shall be equipped with a liquid seal trap.
Principle No. ll-TRAP SEALS SHALL BE PROTECTED

The drainage system shall be designed to provide an adequate circulation of air in all pipes with no danger of
siphonage, aspiration, or forcing of trap seals under conditions of ordinary use.
Principle No. 12-EXHAUST FOUL AIR TO OUTSIDE

Each vent terminal shall extend to the outer air and be so installed as to minimize the possibilities of clogging and
the return of foul air to the building.
Principle No. 13-TESTTHE PLUMBING SYSTEM

The plumbing system shall be subjected to such tests as will effectively disclose all leaks and defects in the work
or the material.
Principle No. 14-EXCLUDE CERTAIN SUBSTANCES FROM THE PLUMBING SYSTEM

No substance which will clog or accentuate clogging of pipes, produce explosive mixtures, destroy the pipes or
their joints, or interfere unduly with the sewage-disposal process shall be allowed to enter the building drainage
system.
Principle No. 15-PREVENT CONTAMINATION

Proper protection shall be provided to prevent contamination of food, water, sterile goods, and similar materials by
backflow of sewage. When necessary, the fixture, device, or appliance shall be connected indirectly with the
building drainage system.
Principle No. 16-LIGHT AND VENTILATION

No water closet or similar fixture shall be located in a room or compartment which is not properly lighted and
ventilated.
Principle No. 17-INDIVIDUAL SEWAGE DISPOSAL SYSTEMS

Ifwater closets or other plumbing fixtures are installed in buildings where there is no sewer within a reasonable
distance, suitable provision shall be made for disposing of the sewage by some accepted method of sewage
treatment and disposal.

Principle No.18-PREVENT SEWER FLOODING
Where a plumbing drainage system is subject to backflow of sewage from the public sewer or private disposal
system, suitable provision shall be made to prevent its overflow in the building.
Principle No. 19-PROPER MAIN TENANCE

Plumbing systems shall be maintained in a safe and serviceable condition from the standpoint of both mechanics
and health.
Principle No.20-FIXTURES SHALL BE ACCESSIBLE

All plumbing fixtures shall be so installed with regard to spacing as to be accessible for their intended use and for
cleaning.
Principle No.21-STRUCTURAL SAFETY

Plumbing shall be installed with due regard to preservation of the strength of structural members and prevention of
damage to walls and other surfaces through fixture usage.
Principle No.22-PROTECT GROUND AND SURFACE WATER

Sewage or other waste shall not be discharged into surface or sub-surface water unless it has first been subjected
to some acceptable form of treatment.

Blank Page
12 200] National Standard FlIInbing Code-Illustrated

Definitions
1.1 GENERAL
For the purpose of this Code, the following terms shall have the meaning indicated in this chapter. No attempt is
made to define ordinary words which are used in accordance with their established dictionary meaning, except
where it is necessary to define their meaning as used in this Code to avoid misunderstanding.
1.2 DEFINITION OF TERMS

Accessible and Readily Accessible:
Accessible means having access thereto without damaging building surfaces, but which first may require
the removal of an access panel, door or similar obstructions with the use oftools.
Readily accessible means direct access without requiring the use of tools for removing or moving any
panel, door or similar obstruction. See Figure 1.2.1
I I
I I
I I
I I
:i VALVE IS ACCESSIBLE IF LATCH
II
~=~ I') Y ISSCREWDRIVER-OPERATED
r TI~lo "
\ ~ II ~
1=~ LJ I~ VALVE IS READILY ACCESSIBLE IF
::
I I
II LATCH IS HANDLE-OPERATED
I I
I I
I I
Figure 1.2.1
AN EXAMPLE OF ACCESSIBLE AND READILY ACCESSIBLE
Acid Waste: See "Special Wastes"
Adopting Agency: The agency, board or authority having the duty and power to establish the plumbing code
which will govern the installation of allplumbing work to be performed in thejurisdictions.
Air Break (drainage system): A piping arrangement in which a drain from a fixture, appliance, or device
discharges into a fixture, receptor, or interceptor at a point below the flood level rim and above the trap seal of the
receptor. See Figure 1.2.2 and Section 9.1.3

Comment: Air breaks are permitted where backflow cannot occur due to back-siphonage.
INDIRECT WASTE PIPE

TERMINATING BELOW
FLOOD LEVEL RIM
OF RECEPTOR
DISCHARGE HOSE
FLOOD LEVEL RIM
t CLOTHES
WASHER
RECEPTOR AIR BREAK
I
TOP OF TRAP SEAL
A. AIR BREAK IN FLOOR SINK B. AIR BREAK IN CLOTHES

WASHER STANDPIPE
Figure 1.2.2
AIR BREAKS
Air Chamber: A pressure surge absorbing device operating through the compressibility of air.
Comment: The Code no longer mentions air chambers. Air chambers were usuallyfield-fabricated and
were initially filled with air at atmospheric pressure. There was direct contact between the captive air
and water, which permitted the air to be absorbed into the water over a period of time. The Code now
callsfor water hammer arrestors, which are pre-charged with compressed air or gas and have bellows or
pistonsthat separatethe airorgasfrom the water. See Figure 1.2.3.
WATER HAMMER ARRESTOR
-. - TO FIXTURE OR APPLIANCE
WITH QUICK CLOSING VALVE
NOTE 2
BRANCH SHUTOFF VALVE
WATER
SUPPLY
NOTES:
1. For maximum effectiveness, the water hammer arrestor should be oriented so that the direction of
the shock wave caused by the quick-closing valve is into the arrestor. Refer to the manufacturer's
instructions.
2. The number of elbows upstream from the water hammer arrestor should be minimized. Each elbow'
represents a point of shock and potential failure.
Figure 1.2.3
A WATER HAMMER ARRESTOR

Air Gap (drainage system): The unobstructed vertical distance through the free atmosphere between the outlet
of the waste pipe and the flood level rim of the receptor into which it is discharging. See Figure 1.2.4
Comment: Air gaps are required where backflow can occur due to back-siphonage.
~ -INDIRECT WASTE PIPE

,- RECEPTOR
AIR GAP
,
Figure 1.2.4
AN AIR GAP FOR INDIRECT WASTE PIPING
Air Gap (water distribution system): The unobstructed vertical distance through the free atmosphere between
the lowest opening from any pipe or faucet supplying water to a tank, plumbing fixture or other device and the
flood level rim of the receptor. See Figure 1.2.5
Comment #1: The minimum required air gap distance is based on the effective opening of the water
supply outlet. The air gap must be increase{lif the outlet is close to walls or other vertical surfaces. See
Section 10.5.2 and Table 10.5.2.
Comment #2: ffair is being {lrawninto the tub spout by a vacuum in the water supply piping, waste
water at the floo{llevel rim of the fixture will tend to be lifted upward towards the spout opening by the
flow of air. The water will lift higher if the spout opening is close to a wall.
TUB SPOUT -,
FLOODLEVELRIM AIRGAPi
OFBATHTUB~
t
~
l.
Figure 1.2.5
AN AIR GAP FOR A POTABLE WATER OUTLET
2003 National Standard ?lImbing Code-IIIlIstrated 15

Anchors: See "Supports." See Chapter 8
Anti-scald Valve: See "Water Temperature Control Valve." See Section 10.15.6
Approved: Accepted or acceptable under an applicable standard stated or cited in this Code, or accepted as
suitable for the proposed use under procedures and powers ofthe Authority Having Jurisdiction as defined in
Sec. 3.12. See Sections 3.1.1, 3.1.2, 3.1.3, and 3.12
Area Drain: A receptor designed to collect surface or storm water from an open area. See Figures 1.2.6 and
13.1.6
WINDOW WELL
DRAIN LESS-----
THAN 10 S.F
(Section 13.1.7) t-,
",'
AREAWAY DRAIN
TO AN APPROVED LESS THAN 100 SF
POINT OF DISPOSAL r/ (Section 13.1.6)
Figure 1.2.6
AREA DRAINS IN WINDOW WELLS AND STAIR WELLS
Aspirator: A fitting or device supplied with water or other fluid under positive pressure which passes through an
integral orifice or "constriction" causing a vacuum. See Figure 1.2.7 and Section 14.13
Comment: Backjlow prevention is required where the jluid supply is potable water.
A - INLET FLUID FLOW

, A
B - INDUCED VACUUM
C - COMBINED OUTLET FLOW
,c
Figure 1.2.7
AN ASPIRATOR FITTING
16 200] National Standard Pumbing Code-Illustrated

Authority Having Jurisdiction: The individual official, board, department, or agency established and authorized
by a state, county, city or other political subdivision created by law to administer and enforce the provisions of the
plumbing code as adopted or amended.
Autopsy Table: A fixture or table used for the postmortem examination of a body.
Comment: Autopsy tables usually involve the use of aspiratorsfor removing botlyjluids. Refer to the
definition of "aspirator".
Backflow Connection: Any arrangement whereby backHow can occur.
I Comment: See "Cross Connection ".
Backflow (drainage): A reversal of How in the drainage system.
Backflow Preventer: A device or means to prevent backflow. See Figures 1.2.5, 1.2.8, 1.2.9, 1.2.23,
1.2.25, 1.2.26, 1.2.27, 1.2.48, 1.2.66, and 1.2.67.
Comment: Refer to the definitions of "backjlow (water distribution)", "back-pressure backjlow",

"back-siphonage", "critical level", "cross connection", "double check valve assembly", "reduced
pressure principle back-pressure backjlow preventor", "vacuum breaker, atmospheric", "vacuum
breaker, pressure type", and "vacuum breaker, spill-prooF'.
POTABLE WATER
TO BUILDING
CHEMICAL SHOT FEEDER
BUILDING VALVE
CURB VALVE BOX
PUBLIC
WATER
~,,'
;;>?
'..
'."\
,A'
.
'
..'
.
MAIN
Figure 1.2.8
BACKFLOW CAUSED BY BACK-PRESSURE

NOTES:
1. Back-pressure backflow is generally caused bywater pressure producing equipment within a
building.
2. The hot water heating boiler operates at up to 30 psig and has a chemical shot feeder.
3. The pressure in the publicwater main can drop below 30 psig due to a shutdown for repair or heavy
demandforfire fightingoperations.
4. The check valve and pressure reducing valve in the water makeupto the heating system are not
adequate to prevent back-pressurebackflow.
5. The chemical feeder creates a potential "high hazard"that requires a reduced pressure zone
backflow preventor (RPZ). Otherwise, a double check valve assemblywould be adequate.
6. An RPZ at Point "A" is required to protect the water distribution system within the building from
backflow of chemically treated boilerwater.
7. An RPZ at Point "B" would "contain" the building and prevent it from backflowing any potential
contamination into the public water system.
Figure 1.2.8 (NOTES)

BACKFLOW CAUSED BY BACK-PRESSURE
"VACUUM BREAKER NEEDED HERE -

/ LOCATED SIX (6 ) INCHES MINIMUM
ABOVE FLOOD LEVEL RIM
-- CHEMICAL SINK FAUCET WITHOUT

BACKFLOW PREVENTER
FLOODLEVEL:Z
II
II
II
II
I'
I
"
II
II
i~
I I ,,
POTABLE WATER SUBJECT
TOBACKFLOW
HW CW
Figure 1.2.9
BACKFLOW CAUSED BY BACK-SIPHONAGE
Backflow (water distribution): The flow of water or other liquids, mixtures, or substances into the distributing
pipes of a potable supply of water from any source or sources other than its intended source. Back-siphonage is
one type of backflow. See Figures 1.2.8 and 1.2.9
Backpressure Backflow: A condition which may occur in the potable water distribution system, whereby a
higher pressure than the supply pressure is created causing a reversal of flow into the potable water piping. See
Figure 1.2.8
Back-siphonage: The flowing back of used, contaminated, or polluted water from a plumbing fixture or vessel
or other sources into a potable water supply pipe due to a negative pressure in such pipe. See Figure 1.2.9

Backwater Valve: A device installed in a drain pipe to prevent backflow. See Figure 1.2.10
Comment: Backwater valves are swing-type check valves that are installed in drainage piping to prevent
the reversal offlow in the piping and overflows due to stoppages,flooding, or other abnormal condi-
tions. Refer to Section 5.5.1for where backwater valves are required.
ACCESS COVER
DIRECTION OF
DRAINAGE FLOW - -- /'
/
/
.....t
-
MECHANJC AL SEAL
-
Figure 1.2.10
A BACKWATER VALVE
Baptistery: A tank or pool for baptizing by total immersion.
Bathroom Group: For the purposes ofthis Code, a bathroom group consists of one water closet, one or two
lavatories, and either one bathtub, one combination bath/shower, or one shower stall, all within a bathing facility in
a dwelling unit. Other fixtures within the bathing facility shall be counted separately when determining the water
supply and drainage fixture unit loads.
Battery of Fixtures: Any group of two or more similar adjacent fixtures which discharge into a common hori-
zontal waste or soil branch. See Figure 1.2.11
Comment: Batteries offixtures can be "battery vented" in groups of up to eight fiXtures in accordance
with Section 12.13. Fixtures that are "battery vented" do not have to be the same type.
PLAN VIEW
Figure 1.2.11
A BATTERY OF FIXTURES
Bedpan Steamer: A fixture used for scalding bedpans or urinals by direct application of steam. See Section
14.10
Bedpan Washer: See Figure 14.8 and Section 14.8.

Boiler Blow-off: An outleton a boilerto permitemptyingor discharge
of sediment. See Figure 1.2.12
I CONTINUOUS SURFACE BLOWOFF
;;...;.,:..i:::;. "
l' ~ FLASHSTEAMVENT
TO OUTDOORS
I
BOILER VENT
BLOWOFF
INLET J TANK -
1-.
:-.:.:.:~
:-: . : . : '=C.-::
.-.-.-.-.
Figure 1.2.12
A BOILER BLOWOFF TANK
Boiler Blow-off Tank: A vessel designed to receive the discharge from a boiler blow-off outlet and to cool the
discharge to a temperature which permits its safe discharge to the drainage system. See Figure 1.2.12
Comment: Boiler blow-off must be cooled to 140F or less before being discharged into the drainage
system. If potable water is supplied for cooling, the water source must be protected from backflow.
An air break can beprovided at the dischargefrom the blow-off tank into the drainage system if the
makeup water supply to the boiler is protected against backflow.
Branch: Any part of the piping system other than a riser, main or stack. See Figure 1.2.13
Comment: Branch piping can serve more than onefIXture or appliance.
20 2003 National Standard Pumbing Code-/IIustrated

T
I /
j
l / / ""- WATER DISTRIBUTION
I BRANCH
WASTE BRANCH / I
1 ""- RISER
Figure 1.2.13
BRANCH PIPING
Branch, Fixture: See "Fixture Branch"
Branch, Horizontal: See "Horizontal Branch Drain"
Branch Interval: A distance along a soil or waste stack corresponding, in general, to a story height, but in no
case less than 8 feet within which the horizontal branches from one floor or story of a building are connected to
the stack. See Figure 1.2.14
Comment: Branch intervals are used to determine the potential drainage load on stacks for the purpose
of sizing the stacks.
SOIL OR WASTE STACK
A-B AND B-D ARE

BRANCH INTERVALS
B-C AND C-D ARE
NOT BRANCH
INTERVALS
A
8' MINIMUM
-
B
/ t=
4' -1 I
8' MINIMUM
.C
4'=j-
D
Figure 1.2.14
BRANCH INTERVALS

Branch Vent: See "Vent, Branch"
Building: A structure having walls and a roof designed and used for the housing, shelter, enclosure or support of
persons, animals or property.
Building Classification: The arrangement adopted by the Authority Having Jurisdiction for the designation of
buildings in classes according to occupancy. See Table 7.21.1
Comment: The building classifications in Table 7.21.1for the minimum number of required plumbing
fIXtures include assembly, business, education, factory and industrial, institutional, mercantile, residen-
tial, storage, and utility/miscellaneous.
Building Drain, Combined: A building drain which conveys both sewage and storm water or other drainage.
See Figure 1.2.15
SOIL
STACK
SOIL
AREA
STACK
DRAIN
RAIN
LEADER
10 FT MINIMUM
FROM STORM
TO SOIL
CONNECTIONS
~ COMBINED
BUILDINGSEWER
Figure 1.2.15
A COMBINED BUILDING DRAINAGE SYSTEM
Building Drain: That part of the lowest piping of a drainage system which receives the discharge from soil,
waste and other drainage pipes inside the walls of the building and conveys it to the building sewer beginning
three (3) feet outside the building wall. See Figure 1.2.16

CD BUILDINGDRAIN- SANITARY
(3) BUILDING DRAIN - STORM
0 BUILDING SEWER - SANITARY /0'::""
0 BUILDING SEWER - STORM
/
~/
/
'" '" ",.
~
"'./ '~
/" .~
END OF BUILDINGDRAINS
lJ,~
~ ""~ ~
'~/!
~>'
r
I
)
"'~~ //
~
~"-PUBLIC
"---
SANITARYSEWER
PUBLICSTORMSEWER
Figure 1.2.16
SEPARATE SANITARY AND STORMWATER BUILDING DRAINS AND SEWERS
Building Drain, Sanitary: A building drain which conveys sewage only. See Figure 1.2.16
Building Drain, Storm: A building drain which conveys stonn water or other drainage, but no sewage, See
Figure 1.2.16
Building Sewer: That part of the drainage system whicQextends from the end of the building drain and conveys
its discharge to a public sewer, private sewer, individual sewage-disposal system or other point of disposal. See
Figure 1.2.16
Building Sewer, Combined: A building sewer which conveys both sewage and stonn water or other drainage.
See Figure 1.2.15
Building Sewer, Sanitary: A building sewer which conveys sewage only. See Figure 1.2.16
Building Sewer, Storm: A building sewer which conveys stonn water or other drainage but no sewage. See
Figure 1.2.16
Building Subdrain: That portion of a drainage system which does not drain by gravity into the building sewer or
building drain. See Figure 1.2.17

VENT VENT
DISCHARGE
TO
GRAVITYDRAIN ~ VENT
SEWAGESUMPPIT
WITHAUTOMATIC
SEWAGEPUMP
OREJECTOR
~% BUILDINGSUBDRAIN
Figure 1.2.17
A BUILDING SUBDRAIN
Building Trap: A device, fitting, or assembly of fittings, installed in the building drain to prevent circulation of air
between the drainage system of the building and the building sewer. See Figure 1.2.18
Comment: Building traps are currently installed only when required by the Authority Having Jurisdic-
tion.
~r}a FRESHAIR INTAKE
VENT NOT LESS THAN

1/2 THE SIZE
OF THE BUILDING
~t:,::::::"C:VEREDI
'.,.. "
DRAIN
~:}l:
---J'--- TO BUILDING SEWER
Figure 1.2.18
A BUILDING TRAP
24 2003 National Standard Pumbing Code-II/ustrated

Cesspool: A lined and covered excavation in the ground which receives the discharge of domestic sewage or
other organic wastes from a drainage system, so designed as to retain the organic matter and solids, but permitting
the liquids to seep through the bottom and sides.
Comment: Chapter 16 does not permit cesspools or cesspits, into which untreated sewage is discharged
and allowed to seep into the ground. Chapter 16 requires septic tanks to retain the sewage until digested
and absorption trenches or seepage pits for underground disposal of the ejj1uent.
Chemical Waste: See "Special Wastes" See Sections 2.10 and 9.4
Circuit Vent: See "Vent, Circuit" See Figure 12.13.1
Clear Water Waste: Effluent in which impurity levels are less than concentrations considered harmful by the
Authority Having Jurisdiction, such as cooling water and condensate drainage from refrigeration and air condition-
ing equipment, cooled condensate from steam heating systems, and residual water from ice making processes.
Comment: Refer to Section 9.1.8for whether a clear water waste requires an air gap or an air break at
its discharge into the drainage system.
Clinical Sink: A sink designed primarily to receive wastes from bedpans, having a flushing rim, intergral trap
with a visible trap seal, and having the same flushing and cleansing characteristics as a water closet. See Section
14.8
Code: These regulations, or any emergency rule or regulation which the Authority Having Jurisdiction may
lawfullyadopt.
Combination Fixture: A fixture combining one sink and laundry tray, or a two- or three-compartment sink or
laundry tray in one unit. See Figure 1.2.19
Comment: CombinationflXtures with waste outlets not more than 30 inches apart can have one trap
/ THREE COMPARTMENTSINK
r SINK AND LAUNDRY TRAY
II II
II II : :l_U_J
I'~-I-j--d ', 'I
Figure 1.2.19
COMBINA TION FIXTURES
Combination Thermostatic/Pressure Balancing Valve: See "ThermostaticlPressure Balancing Valve,

Combined"
Combination Waste and Vent System: A designed system of waste piping embodying the horizontal wet
venting of one or more sinks or floor drains by means of a common waste and vent pipe adequately sized to
provide free movement of air above the flow line of the drain. See Figure 1.2.20 and Section 12.17

Comment #1: Combination waste and vent piping systems are permitted where conditions preclude the
installation of a conventionally vented system. Such systems arefrequently used in exhibition halls and
other spaces where long clear spans are required without partitions or pipe chases.
Comment #2: Onlyfloor drains,floor receptors, sinks, lavatories, and standpipes can be discharged into
a combination waste and vent piping system.
TO CONNECTION WITH
CONVENTIONALLY SIZED
AND VENTED DRAINAGE
PIPING
OVERSIZED COMBINATION WASTE & VENT
PIPING PER TABLE 12.17.4
Figure 1.2.20
COMBINA nON WASTE AND VENT PIPING
Combined Building Drain: See "Building Drain, Combined"
Combined Building Sewer: See "Building Sewer, Combined"
Common Vent: See "Vent, Common"
Conductor: A pipe within a building that conveys storm water from a roofto its connection to a building storm
drain or other point of disposal. See Figure 1.2.21
Comment: A vertical storm water drain pipe on the exterior of a building is a leader.
ROOF DRAIN 1
CONDUCTOR --
TO AN APPROVED
POINT OF DISCHARGE
J1
Figure 1.2.21
A STORMW ATER CONDUCTOR

Continuous Vent: See "Vent, Continuous"
Continuous Waste: A drain from two or more fixtures connected to a single trap. See Figure 1.2.22
Comment: Continuous wastepiping can connect up to three adjacent sinks or lavatories to a single trap
iftheflXture outlets are no more than 30" apart. See Section 5.1.
~~!':@~f;;:pr TRAP
TRAP
END OUTLET CENTER OUTLET
Figure 1.2.22
CONTINUOUS WASTE PIPING
Critical Level: The critical level marking on a backflow prevention device or vacuum breaker is a point estab-
lished by the manufacturer, and usually stamped on the device by the manufacturer, which determines the mini-
mum elevation above the flood level rim of the fixture or receptor served at which the device may be installed.
When a backflow prevention device does not bear a critical level marking, the bottom of the vacuum breaker,
combination valve, or the bottom of any approved device shall constitute the critical level. See Figure 1.2.23 and
Sections lO.5.5.b, c, and e
VACUUM BREAKER
SUPPLY
VALVE
t
POTABLE
WATER
Figure 1.2.23
THE CRITICAL LEVEL (C-L) OF A VACUUM BREAKER

Cross Connection: Any connection or arrangement between two otherwise separate piping systems, one of
which contains potable water and the other either water of questionable safety, steam, gas, or chemical, whereby
there may be a flow ITomone system to the other, the direction of flow depending on the pressure differential
between the two systems (See "Backflow and Back-Siphonage). See Figures 1.2.8 and 1.2.9
Comment: The backflow of contamination into a potable water system through a cross connection can
occur by back-siphonage caused by the water system or back-pressurefrom the source of contamination.
Day Care Center: A facility for the care and/or education of children ranging ITom2-1/2 years of age to 5 years
of age.
Day Nursery: A facility for the care of children less than 2-1/2 years of age.
Dead End: A branch leading from a soil, waste or vent pipe, building drain, or building sewer, and terminating at a
developed length of 2 feet or more by means of a plug, cap, or other closed fitting. See Figure 1.2.24
Comment: An extension of 2feet or more to make a cleanout accessible is not considered to be a dead
end.
VENT l- -,-
: ..
- - -
~
~ DEAD END
:REATERTHAN2 FEET
I
I
I
I
~
""
DRAIN f DEAD END
~REATER THAN2 FEET
Figure 1.2.24
DEAD ENDS IN DRAIN AND VENT PIPING
Developed Length: The length of a pipe line measured along the center line of the pipe and fittings.
Diameter: See "Size of Pipe & Tubing"
28 2003 National Standard Pumbing Code-Il/ustrated

Domestic Sewage: The water-borne wastes derived from ordinary living processes.
DOUBLE CHECK VALVE ASSEMBLY
OPTIONAL
POTABLE
WYE STRAINER l
WATER -I'---- -I'----
SUPPLY
TO LOW HAZARD - BACKPRESSURE

APPLICATIONS
Figure 1.2.25
A DOUBLE CHECK VALVE ASSEMBLY
Double Check Valve Assembly: A backflow prevention device consisting of two independently acting check
valves, internally force loaded to a normally closed position between two tightly closing shut-off valves, and with
means of testing for tightness. See Figure 1.2.25
Double Offset: See "Offset, Double"
Downspout: See "Leader"
Drain: Any pipe which carries waste or water-borne wastes in a building drainage system.
Drainage Pipe: See "Drainage System"
Drainage, Sump: A liquid and air-tight tank which receives sewage and/or liquid waste, located below the
elevation of the gravity system, which shall be emptied by pumping.
Drainage System: Includes all the piping, within public or private premises, which conveys sewage, rain water,
or other liquid wastes to a point of disposal. It does not include the mains of a public sewer system or private or
public sewage-treatment.
Drainage System, Building Gravity: A drainage system which drains by gravity into the building sewer. See
Figure 1.2.16
Drainage System, Sub-building: See "Building Subdrain" See Figure 1.2.17
Dry Vent: See "Vent, Dry"
Dry Well: See "Leaching Well"
Dual Vent: See "Vent, Common"
2003 National Standard Pumbing Code-/llustrated 29

Dwelling Unit, Multiple: A room, or group of rooms, forming a single habitable unit with facilities which are
used, or intended to be used, for living, sleeping, cooking and eating; and whose sewer connections and water
supply, within its own premise, are shared with one or more other dwelling units. Multiple dwelling units include
guest rooms in hotels and motels.
Comment: Apartments, condominiums, and guest rooms in hotels and motels are examples of multiple
dwelling units.
Dwelling Unit, Single: A room, or group of rooms, forming a single habitable unit with facilities which are used,
or intended to be used, for living, sleeping, cooking and eating; and whose sewer connections and water supply are,
within its own premise, separate from and completely independent of any other dwelling.
DWV: An acronym for "drain-waste-vent" referring to the combined sanitary drainage and venting systems.
This term is technically equivalent to "soil-waste-vent" (SWV).
Effective Opening: The minimum cross-sectional area at the point of water supply discharge, measured or
expressed in terms of (1) diameter of a circle, or (2) ifthe opening is not circular, the diameter of a circle of
equivalent cross-sectional area. See Figures 1.2.26 and 1.2.27
Comment: The required air gap distancefor a water supply outlet is based on its effective opening. The
air gap must be increased if the outlet is near a wall or other vertical surface. Refer to Table IO.5.2for
minimum air gapsfor plumbingflXtures.
t AIR GAP NOT LESS
.lcrTHAN'X-O"
EFFECTIVEOPENING(DIAMETER"0")
Figure 1.2.26
THE EFFECTIVE OPENING OF A POTABLE WATER OUTLET
PUMP DISCHARGE TO A
FLOAT NON-POTABLE WATER SYSTEM
VALVE
POTABLE
AIR GAP
t
- SEE TABLE 10.5.2
I-L
WATER --/'--- .;, '\
SUPPLY 0 I
J 0 D'\ 0- EFFECTIVEOPENINGOF WATERSUPPLYOUTLET

PUMP
SUCTION PUMP
TANK
Figure 1.2.27
AN AIR GAP BETWEEN POTABLE AND NON-POTABLE WATER SYSTEMS

Equivalent Length: The length of straight pipe of a specific diameter that would produce the same frictional
resistances as a particular fitting or line comprised of pipe and fittings. See Tables B.9. 7A and B.9.7B
Existing Work: A plumbing system, or any part thereof, installed prior to the effective date of this Code.
Family: One or more individuals living together and sharing the same facilities.
Fixture: See "Plumbing Fixture"
Fixture Branch, Drainage: A drain serving one or more fixtures which discharges into another drain. See
Figure 1.2.28
Comment: See Table 1J.5.J.B for the maximum number of drainagefixture units (DFU) permitted on
each size of horizontal fIXture branch.
VENT
'"t' '"t'
I I
I I
I I
I I
I I
I
I
I
I
FIXTURE DRAINS
Figure 1.2.28
A FIXTURE DRAIN AND FIXTURE BRANCH
Fixture Branch, Supply: A branch ofthe water distribution system supplying one fixture. See Figure 1.2.29
Comment: See Table 1O.14.2.Afor minimum supply fixture branch sizesfor variousfixtures.
G/~SUP)U"
~
1\
FIXTURESTOPVALVE
FIXTURE SUPPLY
BRANCH
Figure 1.2.29
A FIXTURE SUPPLY BRANCH AND FIXTURE SUPPLY TUBE

Fixture Drain: The drain from the trap of a fixture to the junction of that drain with any other drain pipe.
Fixture Supply Tube: A flexible or soft temper water supply tube (or riser), typically 3/8"or 1/2"nominal size
O.D., connecting a water closet ballcock, faucet, appliance or similar fixture to its stop valve andlor fixture supply
branch pipe. See Figure 1.2.29
Comment: Fixture supply tubes can be copper, PVC, PEX, orplastic hose with a stainless steel or
braided polymer jacket. They are limited to 30 inches in length and must be not less than the size
recommended by the manufacturer of thefixture orfaucet
Fixture Unit (Drainage -d.f.u.): An index number that represents the load of a fixture on the drainage system
so that the load of various fixtures in various applications can be combined. The value is based on the volume or
volume rate of drainage discharge from the fixture, the time duration of that discharge, and the average time
between successive uses ofthe fixture. One d.f.u was originally equated to a drainage flow rate of one cubic foot
per minute or 7.5 gallons per minute through the fixture outlet. See Table 11.4.1
Fixture Unit (Water Supply - w.s.f.u.): An index number that represents the load of a fixture on the water
supply system so that the load of various fixtures in various applications can be combined. The value is based on
the volume rate of supply for the fixture, the time duration of a single supply operation, and the average time
between successive uses of the fixture. Water supply fixture units were originally based on a comparison to a
flushometer valve water closet, which was arbitrarily assigned a value of 10 w.s.f.u. See Table 10.14.2A. Also
Tables B.5.2 and B.5.3.
Flood Level: See "Flood Level Rim"
Flood Level Rim: The edge of the receptor or fixture which water overflows. See Figure 1.2.30
Comment: Air gaps are measured from above thejlood level rim of receptors and fixtures.
FLOOD LEVEL RIM
WATER URINAL FLOOR SINK LAVATORY BATHTUB

CLOSET DRAIN
Figure 1.2.30
THE FLOOD LEVEL RIM OF FIXTURES
Flooded: The condition which results when the liquid in a receptor or fixture rises to the flood level rim.

Flow Pressure: The pressure in the water supply pipe near the faucet or water outlet while the faucet or water
outlet is fully open and flowing. See Figure 1.2.31
Comment: The minimum requiredflowing waterpressure for mostfixtures and appliances is 15psig.
Blowout water closets and blowout urinals require 25 psig minimum. Some one-piece water closets
require 30 psig minimum and 1/2" supply tubes.
Figure 1.2.31
THE FLOW PRESSURE OF THE WATER SUPPLY TO AN OUTLET
Flushing Type Floor Drain: A floor drain which is equipped with an integral water supply connection, enabling
flushing of the drain receptor and trap. See Figure 1.2.32
Comment: The water supply toflushing floor drains must be protected from backflow.
DRAIN
TRAP FLUSHING CONNECTION SUPPLIED FROM

AN APPROPIATE BACKFLOW PREVENTION DEVICE
Figure 1.2.32
A FLUSHING TYPE FLOOR DRAIN
Flush Valve: A device located at the bottom of a tank for flushing water closets and similar fixtures. See
Figure 1.2.33

LIFTING MECHANISM
FLAPPER II
'/ FLUSH VALVE ASSEMBLY
Figure 1.2.33
A FLUSH VALVE IN A WATER CLOSET FLUSH TANK
Flushometer Tank: A device integrated within an air accumulator vessel which is designed to discharge a
predetermined quantity of water to the fixture for flushing purposes. See Figure 1.2.34
Comment: Flushometer tanks are pressure-assisted flush tanks that store waterfor flushing water closets
at the inlet water supply pressure, as opposed to gravity tanks. The discharge ratefrom flushometer
tanks is approximately 35 gallons per minute.
PRESSURE TANK
Figure 1.2.34
A PRESSURE-ASSISTED WATER CLOSET WITH A FLUSHOMETER TANK
Flushometer Valve: A device which discharges a predetermined quantity of water to fixtures for flushing
purposes and is closed by direct water pressure or other mechanical means. See Figure 1.2.35
Comment: Flushometer valves are typically used on public water closets and public urinals. They can
be manually operated or electronically operated.

Figure 1.2.35
A FLUSHOMETER VALVE
Force Mains: Force mains deliver waste water discharged from a sewage ejector or pump to its destination
which may be a public or private disposal system, or a higher point in the drainage/sewage system.
Grade: The fall (slope) of a line of pipe in reference to a horizontal plane. In drainage it is usually expressed as
the fall in a fraction of an inch per foot length of pipe. See Figure 1.2.36.
Comment: See Tables 11.5.1A and 11.5.1Bfor sizing building drains, building sewers, and horizontal
fIXture branches. See Table 13.6.2for stormwater drains.
;~~ ~ SLOPING GRAVITYDRAIN
~ " " ~-- FLOW
~ RUN --=1 L FALL
Figure 1.2.36
GRADE ON A SLOPING GRAVITY DRAIN
Grease Interceptor: See "Interceptor"
Grease Trap: See "Interceptor"
Ground Water: Subsurface water occupying the zone of saturation. (a) confined ground water - a body of
ground water overlaid by material sufficiently impervious to sever free hydraulic connection with overlying ground
water. (b) free ground water - ground water in the zone of saturation extending down to the first impervious
barrier.
Half-Bath: For the purposes of this Code, a half-bath or powder room consists of one water closet and one
lavatorywithin a dwellingunit.
Hangers: See "Supports" See Chapter 8

Hazard, High In backflow prevention, an actual or potential threat of contamination to the potable water supply
of a physical or toxic nature that would be a danger to health.
Hazard, Low: In backflow prevention, an actual or potential threat to the physical properties or potability of the
water supply, but which would not constitute a health or system hazard.
High Hazard: See "Hazard, High"
Horizontal Branch Drain: A drain branch pipe extending laterally from a soil or waste stack or building drain,
with or without vertical sections or branches, which receives the discharge from one or more fixture drains and
conducts it to the soil or waste stack or to the building drain.
Horizontal Pipe: Any pipe or fitting which makes an angle of less than 45 with the horizontal. See Figure
1.2.37
Comment: The sizing of offsets in drainage stacks varies depending on whether the offset is horizontal or
vertical. See Section lJ.6.
HORIZONTAL PIPE
(LESS THAN 45)
HORIZONTAL
HORIZONTAL PLANE
Figure 1.2.37
THE DEFINITION OF "HORIZONTAL PIPE"
Hot Water: Potable water at a temperature of not less than 1200pand not more than 140oP.
House Drain: See "Building Drain"
House Sewer: See "Building Sewer"
House Trap: See "Building Trap"
Indirect Connection (Waste): The introduction of waste into drainage system by means of an air gap or air
break without having a direct connection to the drainage system.
Indirect Waste Pipe: A waste pipe which does not connect directly with the drainage system, but which
discharges into the drainage system through an air break or air gap into a trap, fixture, receptor or interceptor.
See Figure 1.2.38

-WALK IN REFRIGERATOR
INDIRECT WASTE PIPE ] SINK
AIR BREAK OR AIR GAP

I I
-c;~--
AIR BREAK OR
(Section 9.1) \ AIRGAP 9.1) \----

(Section .. INDIRECT
WASTEPIPE
INDIRECT WASTE
RECEPTORS
Figure 1.2.38
INDIRECT WASTE PIPES
Individual Vent: See "Vent, Individual"
Industrial Wastes: Liquid or liquid borne wastes resulting from the processes employed in industrial and com-
mercial establishments.
Comment: Industrial wastes must not be discharged into public sewers if they will damage the sewer or
interfere with the operation of the sewage treatment plant.
Insanitary: Contrary to sanitary principles -- injurious to health.
Installed: Altered, changed or a new installation.
Interceptor: A device designed and installed so as to separate and retain deleterious, hazardous, or undesirable
matter from normal wastes while permitting normal sewage or liquid wastes to discharge into the drainage system
by gravity. See Figure 1.2.39
Comment: Interceptors include grease interceptors, oil/water separators, sand interceptors, solids
interceptors, and neutralizing or dilution tanks.
STATIC WATER LINE
FLOW -
/L.--
INVERT
INVERT --./
TRAP SEAL
J
""<OW",
Figure 1.2.39
AN INTERCEPTOR

Invert: The lowest portion of the inside of a horizontal pipe. See Figure 1.2.40
Comment: Invert elevations are used to design and install drainage piping at the required grade or
slope.
HORIZONTAL PIPE
Figure 1.2.40
THE INVERT OF A DRAIN PIPE
Leaching Well or Pit: A pit or receptor having porous walls which permit the contents to seep into the ground.
See Figure 1.2.41
Comment: Leeching wells or pits are used to disperse the effluent from septic tanks into the ground for
secondary treatment. They may supplement or be used in lieu of absorption trenches. Leaching wells or
pits can only be used where there is very deep soil of good permeability and considerable depth to
groundwater.

FROM SEPTIC TANK ---
f
0<1:
I-W
BLOCKS MAY BE LAYERED 00::
WITHOUT MORTAR IN JOINTS w<I:
cnz
:::>0
If::
PLACE BLOCK CELLS IN
-'CL
<1:0::
HORIZONTAL POSITION 50
I-cn
EVERY OTHER COURSE -00
CL<I:
FILL 3" ANNULAR SPACE LLW
01-
WITH CLEAN COURSE 1-:::>
GRAVEL OR CRUSED STONE ICL
e>::a;
wo
IO
t
SECTION
SMALL AMOUNT OF MORTAR

BETWEEN BLOCKS ADDS
RIGIDITY
BUTT BLOCKS FOR

RADIAL ARCH SUPPORT
Figure 1.2.41
A LEACHING OR SEEPAGE WELL OR PIT
Leader: An exterior vertical drainage pipe for conveying storm water from roof or gutter drains. See Figure
1.2.42
Comment: A storm water drain pipe on the interior of a building is a conductor.
] -LEADER
] SPLASH BLOCK OR OTHER

APPROVED POINT OF DISPOSAL
Figure 1.2.42
A STORMW ATER LEADER

Load Factor: The percentage ofthe total connected fixture unit flow which is likely to occur at any point in the
drainage system.
Local Ventilating Pipe: A pipe on the fixture side ofthe trap through which vapor or foul air is removed from a
fixture. See Figure 1.2.43
Comment: Local vent piping may be required for clinical sinks, bedpan washers, and sterilizers. Local
vents for sterilizers must not be connected to local ventsfor clinical sinks and bedpan washers. Refer to
Section 14.9for clinical sinks and bedpan washers. Refer to Section 14.10for sterilizers.
TO OUTDOORS
LOCAL VENT
STERILIZER
-o::or
0
"". "......... " '
Figure 1.2.43
A STERILIZER LOCAL VENTILATING PIPE
Loop Vent: See "Vent, Loop"
Low Hazard: See "Hazard, Low"
Main: The principal pipe artery to which branches may be connected.
Main Sewer: See "Public Sewer"
May: The word "may" is a permissive term.
Medical Gas System: The complete system used to convey medical gases for direct application from central
supply systems (bulk tanks, manifolds and medical air compressors) through piping networks with pressure and
operating controls, alarm warning systems, etc., and extending to station outlet valves at use points.
-
Comment: Medical gas systems must comply with NFPA 99 Standard for Health Care Facilities or
NFPA 99C - Gas and Vacuum Systems. NFPA 99 is the parent document for NFPA 99C. NFPA 99
addresses all safety aspects of health carefacilities, whereas NFPA 99C limits itself to the medical gas
and vacuum portions of NFPA 99.
Medical Vacuum Systems: A system consisting of central-vacuum-producing equipment with pressure and
operating controls, shut-off valves, alarm warning systems, gauges and a network of piping extending to and
terminating with suitable station inlets to locations where suction may be required.
Comment: Refer to the comment under Medical Gas System.
Multiple Dwelling: Building containing two or more dwelling units.

Non-potable Water: Water not safe for drinking or for personal or culinary use.
Nuisance: Public nuisance at common law or in equity jurisprudence; whatever is dangerous to human life or
detrimental to health; whatever building, structure, or premises is not sufficiently ventilated, sewered, drained,
cleaned, or lighted in reference to its intended or actual use; and whatever renders the air or human food or drink
or water supply unwholesome.
Offset: A combination of elbows or bends which brings one section of the pipe out ofline but into a line parallel
with the other section. See Figure 1.2.44 - Parts A and B for single offsets
Comment: Offsets can occur in vertical and horizontal piping. Offsets can consist of90-degree, 45-
degree, or other anglefittings. Single offsets have one change of alignment.
A B c
Figure 1.2.44
OFFSETS IN PIPING
Offset, Double: Two changes of direction installed in succession or series in a continuous pipe. See Figure
1.2.44 - Parts E and F
Comment: Double offsets have two offsets, both awayfrom the original alignment of the pipe.
Offset, Return: A double offset installed so as to return the pipe to its original alignment. See Figure 1.2.44-
Parts C and D
Comment: Return offsets have two offsets, both in different directions. The second offset does not
necessarily bring the pipeline back into exact alignment with thefirst. The alignment of the piping on
both sides of the offset is not necessarily exactly the same laterally.
Oil Interceptor: See "Interceptor"
Person: A natural person, his heirs, executors, administrators or assigns; including a firm, partnership or corpora-
tion, its or their successors or assigns. Singular includes plural; male includes female.
Pitch: See "Grade"
Plumbing: The practice, materials and fixtures within or adjacent to any building structure or Conveyance, used
in the installation, maintenance, extension, alteration and removal of all piping, plumbing fixtures, plumbing appli-
ances, and plumbing appurtenances in connection with any of the following:
a. Sanitary drainage system and its related vent system,
b. Storm water drainage facilities, venting systems,

c. Public or private potable water supply systems,
d. The initial connection to a potable water supply upstream of any required backflow prevention devices and
the final connection that discharges indirectly into a public or private disposal system,
e. Medical gas and medical vacuum systems,
f. Indirect waste piping including refrigeration and air conditioning drainage,
g. Liquid waste or sewage, and water supply, of any premises to their connection with the approved water
supply system or to an acceptable disposal facility.
NOTE:
The following are excluded from the definition:
1. All piping, equipment or material used exclusively for environmental control.
2. Piping used for the incorporation of liquids or gases into any product or process for use in the manufacturing
or storage of any product, including product development.
3. Piping used for the installation, alteration, repair or removal of automatic sprinkler systems installed for fire
protection only.
4. The related appurtenances or standpipes connected to automatic sprinkler systems or overhead or under-
ground fire lines beginning at a point where water is used exclusively for fire protection.
5. Piping used for lawn sprinkler systems downstream from backflow prevention devices.
Plumbing Appliance: Anyone of a special class of plumbing fixture which is intended to perform a special
plumbing function. Its operation and/or control may be dependent upon one or more energized components, such
as motors, controls, heating elements, or pressure or temperature-sensing elements. Such fixtures may operate
automatically through one or more of the following actions: a time cycle, a temperature range, a pressure range, a
measured volume or weight; or the fixture may be manually adjusted or controlled by the user or operator.
Comment: Plumbing appliances include clothes washers, dishwashers,food-waste-disposal and grinder

units, water heaters, water softeners, and similar devices. Refer to Table 3.1.3 - Part VIIfor listed
appliances.
Plumbing Appurtenance: A manufactured device, or a prefabricated assembly, or an on-the-job assembly of

component parts, which is an adjunct to the basic piping system and plumbing fixtures. An appurtenance demands
no additional water supply, nor does it add any discharge load to a fixture or to the drainage system. It is pre-
sumed that an appurtenance performs some useful function in the operation, maintenance, servicing, economy, or
safety of the plumbing system.
Comment: Some examples of plumbing appurtenances are waterfilters, backflow prevention devices,
backwater valves, interceptors, separators, and neutralizing or dilution tanks. Refer to Table 3.1.3 - Part
VIII for listed appurtenances. Plumbing appurtenances do not change the load on the water supply or
drainage system.
Plumbing Fixture: A receptacle or device which is either permanently or temporarily connected to the water
distribution system of the premises, and demands a supply of water therefrom, or discharges used water, liquid-
borne waste materials, or sewage either directly or indirectly to the drainage system of the premises, or which
requires both a water supply connection and a discharge to the drainage system ofthe premises. Plumbing
appliances as a special class of fixture are further defined.
Comment: Plumbing fixtures include water closets, urinals, bidets, lavatories, bathtubs, whirlpool baths,
showers, sinks, floor drains, and receptors. Refer to Table 3.1.3 - Part Vfor listed plumbingfLXtures.
42 2003 National Standard Pumbing Code~f{{ustrated

Plumbing Inspector: See "Authority Having Jurisdiction"
Plumbing System: Includes the water supply and distribution pipes, plumbing fixtures and traps; soil, waste and
vent pipes; sanitary and storm drains and building sewers; including their respective connections, devices and
appurtenances to an approved point of disposal.
Pollution: The addition of sewage, industrial wastes, or other harmful or objectionable material to water.
Sources of sewage pollution may be privies, septic tanks, subsurface irrigation fields, seepage pits, sink drains,
barnyard wastes, etc.
Pool: See "Swimming Pool"
Potable Water: Water free from impurities present in amounts sufficient to cause disease or harmful physiologi-
cal effects and conforming in its bacteriological and chemical quality to the requirements of the Public Health
Service Drinking Water Standards or the regulations of the public health authority havingjurisdiction.
IPowder Room: See "Half-Bath."
Pressure Balancing Valve: A mixing valve which senses incoming hot and cold water pressures and compen-
sates for fluctuations in either to stabilize its outlet temperature.
Comment: Pressure balancing control valvesfor individual bathing facilities must comply with ANSI/
ASSE 1016, Type P.
Private Sewage Disposal System: A system for disposal of domestic sewage by means of a septic tank or
mechanical treatment, designed for use apart from a public sewer to serve a single establishment or building. See
Chapter 16
Private Sewer: A sewer not directly controlled by public authority.
Comment: A private sewer connects a building to a private sewage disposal system.
Private Water Supply: A supply, other than an approved public water supply, which serves one or more build-
ings. See Figure 1.2.46 and Chapter 17
WELL SEAL ;~.I --- PRESSURE TANK

(Section 17.9.1) '. (Section 17.2.4.A)
:~tl
- TO POINTOF USE
PITLESS ADAPTER :'~1".~" ','~""" .,." ".;.. .1;. ::",,"..,.,
WATER ..'
SERVICE TANK DRAIN
PIPE (Section 17.5.5)
SUBMERSIBLE PUMP
WELL CASING (Section 17.6)
Figure 1.2.46
A TYPICAL PRIVATE WATER SUPPLY SYSTEM

Public Sewer: A common sewer directly controlled by public authority.
Comment: This Code does not coverpublic sewers. The design and construction of public sewers is
regulated by the sewage authority, a public works department, or other Authority Having Jurisdiction.
Public Toilet Room: A toilet room intended to serve the transient public, such as in, but not limited to the
following examples: service stations, train stations, airports,restaurants, and convention halls.
Public Water Main: A water supply pipe for public use controlled by public authority.
Comment: This Code does not coverpublic water mains. The design and construction of public water
mains is regulated by the waterpurveyor, a public works department, or other Authority Having Juris-
diction.
Receptor: A fixture or device which receives the discharge from indirect waste pipes. See Figure 1.2.47
Comment: Receptors include jloordrains, standpipes, and certain sinks.
OPEN TOP OR
FULL I PARTIAL TOP GRATE
, "
..,. .
~
.." " . ,..
.~
~"
.~ J
:)
.. " . "'. . ..',?
. .'"
~ . ~
. ~ D. ~ . ~
..
". I
I
FLOOR SINK
Figure 1.2.47
AN INDIRECT WASTE RECEPTOR
Reduced Pressure Principle Backpressure Backflow Preventer: A backflow prevention device consisting
of two independently acting check valves, internally force loaded to a normally closed position and separated by an
intermediate chamber (for zone), in which there is an automatic relief means of venting to atmosphere internally
loaded to a normally open position between two tightly closing shut-off valves and with means for testing for
tightness of the checks and opening of relief means. See Figure 1.2.48
Comment: Reduced pressure principle backjlow preventor assemblies provide the highest level of
protection against backpressure backjlow. The shutoff valves on these assemblies are resiliently seated
to assure tight close-off for testing. Provisions must be made to drain any dischargefrom the relief vent
outlet, which may occur due to normal variations in system pressure.

TEST
COCK
FLOW --- FLOW ---
/"
OPTIONAL
STRAINER
VENT OUTLET
Figure 1.2.48
A REDUCED PRESSURE BACKFLOW PREVENTER ASSEMBLY
Relief Vent: See "Vent, Relief'
Return Offset: See "Offset, Return"
Revent Pipe: See "Vent, Individual"
Rim: An unobstructed open edge of a fixture. See Figure 1.2.30
Comment: Theflood level rim of afIXture or appliance is the levelfrom which it will overflow if its drai,
outlet is closed or blocked.
Riser: A water supply pipe which extends vertically one full story or more to convey water to branches or to a
group of fixtures. See Figure 1.2.49
Comment: The term "riser" refers to vertical water supply piping serving one or more fixtures in
buildings having one or more story heights.
TO FIXTURES
TO FIXTURES
WATER SUPPLY
RISER
TO FIXTURES
'- RISER SHUT OFF VALVE
Figure 1.2.49
A WATER SUPPLY RISER

Roof Drain: A drain installed to receive water collecting on the surface of a roof and to discharge it into a leader
or a conductor. See Figure 1.2.50
Comment: Roof drains include flat deck drains and scupper drains.
Figure 1.2.50
A GENERAL PURPOSE ROOF DRAIN
Roughing-in: The installation of all parts of the plumbing system which can be completed prior to the installation
of fixtures. This includes drainage, water supply, and vent piping, and the necessary fixture supports, or any
fixtures that are built into the structure.
Safe Waste: See "Indirect Waste Pipe"
Sand Filter: A treatment device or structure, constructed above or below the surface of the ground, for removing
solid or colloidal material of a type that cannot be removed by sedimentation, from septic tank effluent. See
Figure 1.2.51 and Section 16.12
Comment #1: Sand filters provide additional treatment of septic tank effluent. They are used where the
soil depth is shallow and cannot provide sufficient secondary treatment of the effluent.
Comment #2: Sand interceptors (or sand traps) are associated with oil/water separators in Chapter 6.
/ REMOVABLECOVER
----
Figure 1.2.51
A SAND FILTER FOR SEPTIC TANK EFFLUENT
Sand Interceptor: See "Interceptor" See Section 6.4
Comment: Sand interceptors (or sand traps) are associated with oil/water separators in Chapter 6. Sand
filters are associated with the effluent from septic tanks in Chapter 16.

Sand Trap: See "Interceptor"
Comment: The term "sand trap" is used interchangeably with "sand interceptor. "
Sanitary Sewer: A sewer which carries sewage and excludes storm, surface and ground water.
SDR: An abbreviation for "standard dimensional ratio", which relates to a specific ratio ofthe average specified
outside diameter to the minimum wall thickness for outside controlled diameter plastic pipe.
Seepage Well or Pit: See "Leaching Well"
Septic Tank: A watertight receptacle which receives the discharge of a building sanitary drainage system or part
thereof, and is designed and constructed so as to separate solids from the liquid, digest organic matter through a
period of detention, and allow the liquids to discharge into the soil outside of the tank through a system of openjoint
or perforated piping, or a seepage pit. See Figure 1.2.52 and Section 16.6
Comment: Figure 1.2.52 shows baffles at the inlet and outlet connections with two access covers.
Figure 16.6.6 shows 6" long drop pipes on the inlet and outlet connections with cleanouts and a single
access cover. Both arrangements perform the same functions and either arrangement is acceptable.
~CESS COVER
Figure 1.2.52
A TYPICAL SEPTIC TANK
Service Sink: A sink or receptor intended for custodial use that is capable of being used to fill and empty a
janitor's bucket. Included are mop basins, laundry sinks, utility sinks, and similar fixtures. (See Table 7.21.1)
Sewage: Liquid containing human waste (including fecal matter) and/or animal, vegetable, or chemical waste
matter in suspension or solution.
Sewage Ejector, Pneumatic: A device for lifting sewage by air pressure. See Sections 11.7 and 12.14.3
Sewage Pump: A permanently installed mechanical device, other than an ejector, for removing sewage or liquid
waste from a sump. See Figure 1.2.54 and Section 11.7
Comment: Figure 1.2.54 shows a pedestal-type sewage pump. Sewage pumps can also be submersible
pumps or dry pit centrifugal pumps.

LEVEL CONTROL SWITCH
AND HIGH LEVEL ALARM
-VENT
SECTION11.7.4
FROM BUILDING -~'; / .~;:f;::1

SUB- DRAIN h-::<'
1~
:<7 F~?
1
WATER-TIGHT
'NeET J 1) _-8,;r~
i;~~FJ DRAINAGE SUMP
FLOAT.-/
~-
,;~~'.~
.
<;~;j
;'::f::
i~$~';'i~iij{!N?:j!;~ti1;
Figure 1.2.54
A PEDESTAL TYPE SEWAGE PUMP
Shall: "Shall" is a mandatory tenn.
Shock Arrestor (mechanical device): A device used to absorb the pressure surge (water hammer) which
occurs when water flow is suddenly stopped. See Figure 10.14.7 and Section 10.14.7 for Water Hammer
Arrestors. Also Figure 1.2.3
Comment: Water hammer arrestors are either the bellows orpiston type and are pre-charged with
compressed air or gas. The Code no longer mentions air chambers, which are subject to losing their
initial captive air charge through absorption into the system water.
Short Term: A period oftime not more than 30 minutes.
Side Vent: See "Vent, Side"
Sink, Commercial: A sink other than for a domestic application. Commercial sinks include, but are not limited to:
1. pot sinks;
2. scullery sinks;
3. and sinks used in photographic or other processes.
Size of Pipe and Tubing: The nominal inside diameter in inches as indicated in the material standards in Table
3.1.3. If outside diameter is used, the size will be followed by "o.d.".
Size of Pipe and Tubing, Incremental: Where relative size requirements are mentioned, the following schedule
of sizes is recognized, even if all sizes may not be available commercially: 1/4,3/8, 1/2,3/4, 1, 1-1/4, 1-1/2,2,2-1/2,
3,3-1/2,4,4-1/2,5,6,7,8,10,12,15,18,21,24.
ISlip Joint: A connection in drainage piping consisting of a compression nut and compression washer that penn its

drainage tubing to be inserted into the joint and secured by tightening the compression nut. Slip joints are typically
used in trap connections for lavatories, sinks, and bathtubs. They permit the trap to be removed for cleaning or
replacement, and to provide access to the drainage piping.
Slope: See "Grade"
Soil Pipe or Soil Stack: Pipes which convey sewage containing fecal matter to the building drain or building
sewer.
Special Wastes: Wastes which require special treatment before entry into the normal plumbing system. See
Figures 1.2.55 and 9.4.1. Also Section 9.4
Comment: Figure 1.2.55 shows a neutralizing tank for acid waste using limestone or marble chips.
Figure 9.4.1 shows an automatic neutralizing tank that could treat either acid or caustic wastes, depend-
ing on the neutralizing solution used.
~
ACCESSCOVER
INLET---
~ SIDEOR TOPV'NT
OUTLET---
u;
.C>-/' ~ E;:j FILL LEVEL OF
LIMESTONE OR
MARBLE CHIPS
2" x 3"
.lS
Figure 1.2.55
A NEUTRALIZING TANK FOR ACID WASTE
Special Waste Pipe: Pipes which convey special wastes. See Section 3.11 for acceptable piping materials
Stack: A general term for any vertical line including offsets of soil, waste, vent or inside conductor piping. This
does not include vertical fixture and vent branches that do not extend through the roof or that pass through not
more than two stories before being reconnected to the vent stack or stack vent. See Figure 1.2.56, Section
11.5.2, and Table 11.5.1B
Comment: Stacks include soil stacks, waste stacks, vent stacks, and stack vents. See separate definitions.

1"
I
r4 1I
VENTSTACK - I
I
I
I
I
I-STACK
I
I
I W.C.
VENT
W.C. W.C.
LAV I LAV
SECONDSTORY-,-
I
~
- SOIL STACK
r---r--,
I I I I
I I I I
DRINKING I LAV I LAV I LAV I
FOUNTAIN
W.C. W.C.
FIRST STORY -.-
BASEMENT
Figure 1.2.56
A STACK VENT
Stack Group: A group of fixtures located adjacent to the stack so that by means of proper fittings, vents may be
reduced to a minimum. See Section 12.11 for stack venting groups of fixtures
Stack Vent: The extension of a soil or waste stack above the highest horizontal drain connected to the stack.
See Figure 1.2.56
Stack Venting: A method of venting a fixture or fixtures through the soil or waste stack. See Figure 1.2.57
and Section 12.11
l'
I
I
I
TUBISHOWER
Figure 1.2.57
STACK VENTING
Storm Drain: See "Drain, Storm"
Storm Sewer: A sewer used for conveying rainwater, surface water, condensate, cooling water, or similar liquid
wastes.
Subsoil Drain: A drain which collects subsurface or seepage water and conveys it to a place of disposal. See
Figure 1.2.59 and Section 13.1.5 for foundation drains
Comment: Refer to Table 3.8for acceptable materialsfor subsoil drains.

I
I
I
. I
,"",
,""'''''
, I
I
1
.;;: I1
~':.-;.
~,.,/
GRAD E //-'/
~~//- .
~,.,./
~,.,./
h.~/-'/ .
/~/
/ ~///
~~///
/-'/
Figure 1.2.59
SUBSOIL DRAIN PIPING
Suction Line: The inlet pipe to a pump on which a negative pressure may exist under design conditions.
Sump: A tank or pit which receives liquid wastes only, located below the elevation of the gravity system, which
shall be emptied by pumping.
Sump, Drainage: A liquid and air-tight tank which receives sewage and/or liquid waste, located below the
elevation of the gravity system, which shall be emptied by pumping. See Figure 1.2.54
Sump Pump: A permanently installed mechanical device for removing clear water or liquid waste from a sump.
See Figure 1.2.60
SWITCH
MOTOR
LIFTING HANDLE
PEDESTAL
DRIVE SHAFT
FLOAT
DISCHARGE
INLET SCREEN
PUMP BODY DISCHARGE
A. SUBMERISBLE TYPE B. PEDESTAL TYPE
Figure 1.2.60
DIFFERENT TYPES OF SUMP PUMPS
Supports: Devices for supporting and securing pipe, fixtures and equipment. See Chapter 8

Swimming Pool: Any structure, basin, chamber or tank containing an artificial body of water for swimming,
diving, or recreational bathing. See Section 9.1.11
Tempered Water: Water at a temperature of not less than 900Pand not more than 105P.
Thermostatic/Pressure Balancing Valve, Combination: A mixing valve which senses outlet temperature and
incoming hot and cold water pressure and compenstates for fluctuations in incoming hot and cold water tempera-
tures and/or pressures to stabilize its outlet temperatures.
Comment: Combination thermostatic/pressure balancing control valves are usedfor individual bathing
facilities and must comply with ANSI/ASSE 1016, Type PT.
Thermostatic (Temperature Control) Valve: A mixing valve which senses outlet temperature and compen-
sates for fluctuations in incoming hot or cold water temperatures.
Comment: Thermostatic control valves usedfor individual bathing facilities must comply with ANSI/
ASSE 1016, Type T. Thermostatic control valvesfor other point-ol-use applications should comply with
the appropriate standard.
Toilet Facility: A room or combination of interconnected spaces in other than a dwelling that contains one or
more water closets and associated lavatories, with signage to identify its intended use.
Trap: A fitting or device which provides a liquid seal to prevent the emission of sewer gasses without materially
affecting the flow of sewage or waste water through it. See Figure 1.2.62 and Sections 5.1, 5.2, and 5.3
CROWN WEIR OF TRAP
TRAP DIP
Figure 1.2.62
ELEMENTS OF A FIXTURE TRAP
Trap Arm: A trap arm is that portion of a fixture drain between a trap and its vent. See Figure 1.2.63 and
Section 12.8.1
Comment: Refer to Table 12.8.1for the maximum allowable length of trap arms to avoid trap siphon-
age.
52 2003 National Standard Pumbing Code-!l/ustrated

INSIDE WALL
OF PIPE
DISTANCE FROM
- VENT
jlt
TRAP TO VENT
J y-- TOPOF VENTOPENING
TRAP WEIR
NOTES:
1 rw~~
1. The top of the opening to the vent at the end of the trap arm must not be below the weir of the trap.
Figure 1.2.63
THE LENGTH OF A TRAP ARM
Trap Primer: A trap primer is a device or system of piping to maintain a water seal in a trap. See Figures
1.2.64 and 1.2.65. Also Section 7.16.2
SUPPLY---- TO FIXTURE
INTEGRAL AIR GAP
~
TO TRAP
Figure 1.2.64
A FLOW-ACTIVATED TRAP PRIMER
POTABLE WATER LINE
TRAP PRIMER
TRAP SEAL
TRAP
Figure 1.2.65
CONNECTION OF A TRAP PRIMER TO A TRAP

Trap Seal: The maximum vertical depth of liquid that a trap will retain, measured between the crown weir and
the top of the dip of the trap. See Figure 1.2.62and Section 5.3.2
Vacuum: Any pressure less than that exerted by the atmosphere.
Vacuum Breaker: See "Backflow Preventer"
Vacuum Breaker, Non-pressure Type (Atmospheric): A vacuum breaker which is not designed to be
subject to static line pressure. See Figure 1.2.66
A. THREADED TYPE ATMOSPHERIC B. HOSE TYPE ATMOSPHERIC
Figure 1.2.66
TYPES OF ATMOSPHERIC VACUUM BREAKERS
Vacuum Breaker, Pressure Type: A vacuum breaker designed to operate under conditions of static line
pressure. See Figure 1.2.67
Figure 1.2.67
A PRESSURE TYPE VACUUM BREAKER

Vacuum Breaker, Spill-proof (SVB): A pressure-type vacuum breaker specifically designed to avoid spillage
during operation, consisting of one check valve force-loaded closed and an air inlet vent valve force-loaded open to
atmosphere, positioned downstream of the check valve, and located between and including two tightly closing shut-
off valves and a means for testing.
Comment. SVB vacuum breakers are spill-resistant, not spill-proof
Vacuum Relief Valve: A device to prevent vacuum in a pressure vessel. See Figure 1.2.69 and Section
10.16.7
Comment: Vacuum relief valves are required on storage-type hot water heaters that are located above
the flXtures that they serve toprevent the tank from being siphoned dry and damaged by dry-firing.
Figure 1.2.69
A VACUUM RELIEF VALVE
Vent, Branch: A vent connecting one or more individual vents with a vent stack or stack vent. See Figure
1.2.70
~~~:;:~:~T '
n
1 I URINAL I I
I 1 l I
w.e.1 w.e.1 I LAV I LAV
I --'11I
,- ""''''' ' -" ""'''-'--,-",,,,,, , "-""'''' '-' . ..-.------......
Figure 1.2.70
A BRANCH VENT
Vent, Circuit: A vent that connects to a horizontal drainage branch and vents from two to eight traps or trapped
fixtures connected in a battery. See Figure 1.2.71

Comment: Circuit vents connect to vent stacks. Loop vents connect to stack vents.
SOIL STACK VENTSTACK ~

r T ~
I i 1- i
RELIEF
VENT - I~I
I
i--l-
I
CIRCUITVENT
I
I w.c. w.c. w.c. I wC I
-.-i-~ ~ ~-i-~ I-
I
..\.,
Figure 1.2.71
A CIRCUIT VENT
Vent, Common: A vent connected at a common connection oftwo fixture drains and serving as a vent for both
fixtures. See Figure 1.2.72
'I
I-- COMMON VENT

Figure 1.2.72
A COMMON VENT
Vent, Continuous: A vertical vent that is a continuation of the drain to which it connects. See Figure 1.2.73
56 2003 National Standard Pumbing Code-ll/ustrated

rI~ CONTINOUS VENT
I
I
lAV II
1'- FI~URE:~IN
Figure 1.2.73
A CONTINUOUS VENT
Vent, Dry: A vent that does not receive the discharge of any sewage or waste.
Vent, Individual: A pipe installed to vent a fixture drain. It connects with the vent system above the fixture
served or terminates outside the building into the open air. See Figure 1.2.74
"t'
I
lAV
I
:- INDIVIDUAL VENT
FIXTURE DRAIN
Figure 1.2.74
AN INDIVIDUAL VENT

Vent, Loop: A circuit which loops back to connect with a stack vent instead of a vent stack. See Figure
1.2.75
Comment: Loop vents connect to stack vents. Circuit vents connect to vent stacks.
'1'
LOOP VENT ~ :
i l
I I
I I 8TACK VENT
I I
w.C. I W.C. W.C. I
-Y-i-Y-r 1-
Figure 1.2.75
A LOOP VENT
Vent, Relief: An auxiliary vent which permits additional circulation of air in or between a drainage and vent
system. See Figures 12.3.1, 12.3.2, 12.3.3-A, 12.3.3-B, 12.13.1, 12.15.1, and 12.16.2
Comment: Reliefvents are required atpoints in some vertical drainage stacks, at horizontal offsets in
some drainage stacks, at the base of some stacks, and at some battery vented branch connections to
stacks. Refer to Chapter 12.
Vent, Side: A vent connecting to the drain pipe through a fitting at an angle not greater than 45 to the vertical.
See Figure 1.2.76
'I
I
I
~
I
VENT
/ )
/
~ SIDE VENT
d ~ SIDE VENT
VERTICAL DRAIN
-"-. HORIZONTALDRAIN
Figure 1.2.76
SIDE VENTS
Vent, Sterilizer: A separate pipe or stack, indirectly connected to the building drainage system at the lower

terminal, which receives the vapors from non-pressure sterilizers, or the exhaust vapors from pressure sterilizers,
and conducts the vapors directly to the outer air. Sometimes called vapor, steam, atmosphere or exhaust vent.
See Section 14.11
Vent, Wet: A vent which receives the discharge of wastes other than from water closets and kitchen sinks. See
Figure 1.2.77. Refer to Section 12.10 for other arrangements of wet venting.
Figure 1.2.77
A WET VENT
Vent, Yoke: A pipe connecting upward from a soil or waste stack to a vent stack for the purpose of relieving
pressures in the stack. See Figure 1.2.78
Comment: A yoke vent is vertical. No portion of a yoke vent can be horizontal.
l'
I
1'"
II '1
I
I
VENT STACK ~ l(r- YOKE VENT
SOIL OR WASTE STACK
(Section12_3_1)- I
I
-t
Figure 1.2.78
A YOKE VENT
Vent Pipe: Part of the vent system.

Vent Stack: A vertical vent pipe installed to provide circulation of air to and from the drainage system and which
extends through one or more stories. See Figures 1.2.71 and 12.3.1
Vent System: A pipe, or pipes, installed to provide a flow of air to or from a drainage system or to provide a
circulation of air within such system to protect trap seals from siphonage and back pressure. See Figure 1.2.79
VERTICAL
VERTICAL PIPE (45' OR MORE)
HORIZONTAL PLANE
VERTICAL
Figure 1.2.79
THE DEFINITION OF "VERTICAL PIPE"
Vertical Pipe: Any pipe or fitting which makes an angle of 45 or more with the horizontal. See Figure 1.2.79
Wall Hung Water Closet: A water closet installed in such a way that no part of the water closet touches the
floor. See Figure 1.2.80
1
1
j
g
WALL
FLOOR
///////////
Figure 1.2.80
A WALL HUNG WATER CLOSET
Waste: Any liquid or liquid-borne material or residue intended to be discarded that remains after any activity or
process but not including any such materials that contain animal or human fecal matter.
Waste Pipe: A pipe which conveys only waste.

Waste Stack, Pipe or Piping: Pipes which convey the discharge from fixtures (other than water closets),
appliances, areas, or appurtenances, which do not contain fecal matter.
Water Distribution Pipe: A pipe within the building or on the premises which conveys water from the water-
service pipe to the point of usage. See Figure 1.2.81
LAVATORY
TO UPPER FLOORS ~
l W.C. 1)-/<-
r,: LAVATORY J/-~5-//
II Ij//~/
BATHTUB
SHOWER
~y/W.C.
~;:-C t/
",,/
1
1
I I
I I ,,/" TO FIXTURES
': /",,/
l~/-/
II'~
I,
I I
1"=1>- WATER D
I, I' RISERS ISTRIBUTION
I'~~, WATER DISTRIBUTION

BRANCHES
I""""/~' '",
, ,,
I "" '
'
II
': '~"
~
1.1. ' "
,,~~
FROM SOURCE
,,///
// "/
COLD -----
HOT n-
Figure 1.2.81
WATER DISTRIBUTION PIPING

Water Lifts: See "Sewage Ejector"
Water Main: A water supply pipe for public use. See "Public Water Main"
Water Outlet: A discharge opening through which water is supplied to a fixture, into the atmosphere (except into
an open tank which is part of the water supply system), to a boiler or heating system, to any devices or equipment
requiring water to operate but, which are not part of the plumbing system.
Water Riser Pipe: See "Riser"
Water Service Pipe: The pipe from the water main, or other source of potable water supply, to the water
distributing system of the building served. See Figure 1.2.82 and Section 10.6
CURB BOX OR
WATER METER
AT PROPERTY LINE
STREET
WATER DISTRIBUTION PIPING
(Section 10.12.2)
BUILDING
VALVE AND DRAIN
(Section 10.12.1)
CORPORATION APPROVED I', "/'; ~:;;.: +
SHUT-OFF
(Section 10.6.4)
COCK? / VALVE
SLEEVEAND SEALANT
"-- WATERSERVibE PIPETO BUILDING
..It!.
EJ3J
Figure 1.2.82
THE WATER SERVICE PIPE IN A PUBLIC WATER SUPPLY
Water Supply System The water service pipe, the water-distributing pipes, and the necessary connecting pipes,
fittings, control valves, and appurtenances in or adjacent to the building or premises.
Water Temperature Control Valve A valve of the pressure balance, thermostatic mixing, or combination
pressure balance/thermostatic mixing type, which is designed to control water temperature to reduce the risk of
scalding.
Wet Vent See "Vent, Wet"
62 2003 National Standard Pumbing Code-I/Iustrated

Whirlpool Bathtub A plumbing appliance consisting of a bathtub fixture which is equipped and fitted with a
circulation piping system, pump, and other appurtenances and is so designed to accept, circulate, and discharge
bathtub water upon each use. See Figure 1.2.83
~\: o~ ~~L
Figure 1.2.83
A WHIRLPOOL BATH
Weir (trap or crown) Discharge overflow ofthe trap outlet.
Yoke Vent See "Vent, Yoke:

Blank Page

- - - -- -- - - - - -'- - --
- -- - ---
--- ----
.' -". ' '0

"C, "','
. Cbap~~r,t~;c
General Regulations
2.1 RESERVED
2.2 RESERVED
2.3 CHANGES IN DIRECTION OF DRAINAGE PIPING
2.3.1 Uses for Drainage Fittings
a. Changes in direction of drainage piping shall be made with long radius drainage fittings. See Table
2.3.1.
EXCEPTION: Short radius drainage fittings shall be permitted in the drain piping for individual fixtures. See
Table 2.3.1.
b. Short radius drainage fittings are those having radius or centerline dimensions that are approximately
equal to or less than their nominal pipe size. The radius or centerline dimensions oflong radius drainage
fittings are greater than their nominal pipe size.
c. Long radius drainage fittings shall not be used to connect fixture trap arms to vertical drain and vent
piping. Connections to fixture vents shall be above the top weir ofthe fixture trap.
See Figures 2.3.1-A, 2.3.1-B, 2.3.1-C, and 2.3.1-D
r VERTICAL
r VERTICAL
r VERTICAL
-
r
[ VERTICAL
HORIZONTAL
SANITARY TEE WYE AND 1/8 BEND SWEEP OR DOUBLE COMBINATION

QUARTER BEND
NOTES:
1. Horizontal-to-verticalchanges in direction are not as critical as other changes because gravity
controls the velocity in vertical drops.
2. No-hub cast iron fittings are shown. See Table 2.3.1 for fitting patternsfor other drainage pipe
materials.
3. Short pattern fittings are permitted in piping for individual fixtures.
4. Long pattern fittings are not permitted to connect fixture trap arms to vertical and vent piping
because the vent opening at the end of the trap arm will be below the weir of the trap, causing the
trap to self-siphon.
Figure 2.3.1 A -
DRAINAGE FITTINGS FOR HORIZONTAL-TO-VERTICAL

CHANGES IN DIRECTION
COMBINATION WYE
& 1/8 BEND
WYE AND 1/8 BEND
PLAN VIEW
NOTES:
1. Long pattern fittings are required except short pattern fittings are permitted for individual fixtures.
2. No-hub cast iron fittings are shown. See Table 2.3.1 for fitting patterns for other drainage pipe
materials.
Figure 2.3.1 - B
DRAINAGE FITTINGS FOR HORIZONT AL-TO-HORIZONTAL
r VERTICAL
COMBINATION WYE
AND 1/8 BEND
-- HORIZONTAL
LONG SWEEP
QUARTER BEND
TO BE EQUIVALENT
TO WYE AND
1/8 BEND ELEVATION VIEW
NOTES:
1. Long pattern fittings are required except short pattern fittings are permitted for individual fixtures.
materials.
3. See Sections 11.11 and 12.15 for restrictions on branch drain connections near the base of stacks
that are subject to suds pressure.
Figure 2.3.1 - C
DRAINAGE FITTINGS FOR VERTICAL- TO-HORIZONTAL
66 2003 National Standard PUn/bing Code-Illustrated

TABLE 2.3.1 PERMISSIBLE DRAINAGE FITTINGS FOR CHANGES IN DIRECTION
CHANGE IN DIRECTION
PIPE HORIZONTAL HORIZONTAL VERTICAL
MATERIAL TO TO TO
HORIZONTAL VERTICAL HORIZONTAL
long sweep sanitary tee (I) eighth bend and wye
short sweep eighth bend and wye (2) combination wye & eighth bend
CAST IRON wye combination wye & eighth bend (2) long sweep
HUB & SPIGOT combination wye & eighth bend long sweep short sweep 3" or larger
fifth bend (72 deg) short sweep quarter bend (I)
CAST IRON sixth bend (60 deg) quarter bend ( I ) short sweep (I)
NO-HUB eighth bend (45 deg)
sixteenth bend (22-1/2 deg)
quarter bend ( I)
extra long turn 90-deg elbow drainage tee (I) long turn 90 deg TY
long turn 90-deg elbow short turn 90 deg TY (I) extra long turn 90-deg elbow
long turn 45-deg elbow long turn 90 deg TY (2) long turn 90-deg elbow
CAST IRON short turn 22-1/2 deg elbow 45-deg elbow and 45-deg Y branch (2) short turn 90-deg elbow (I)
DRAINAGE short turn 11-1/4 deg elbow extra long turn 90 deg elbow 45-deg elbow and 45-deg Y branch (I)
(threaded) long turn 90-deg TY long turn 90 deg elbow
short turn 45 deg Y branch short turn 90-deg elbow (I)
short turn 90-deg elbow (I)
DWV 90-deg long radius elbow DWV tee (I) DWV long turn T-Y
90-deg elbow - long radius DWV 90-deg sanitary tee (I) 45-deg elbow and DWV 45-deg Y
COPPER DWV long turn T-Y DWV long turn T-Y (2) DWV 90-deg long radius elbow
DWV DWV 45-deg Y 45-deg elbow and DWV 45-deg Y (2) 90-deg elbow - long radius
DWV 90-deg elbow (I) DWV 90-deg long radius elbow DWV 90-deg elbow (I)
DWV 45-deg elbow (I) 90-deg elbow - long radius
DWV 90-deg elbow (1)
90-deg long turn elbow sanitary tee (I) long radius TY
long sweep 1/4 bend fixture tee (I) 45-deg elbow and 45-deg wye
60-deg elbow or 1/6 bend long radius TY (2) 90-deg long turn elbow
PLASTIC 45-deg elbow or 1/8 bend 45-deg elbow and 45-deg wye (2) 90-deg elbow or 1/4 bend (I)
DWV 22-1/2 deg elbow or 1/16 bend 90-deg long turn elbow
long radius TY 90-deg elbow or 1/4 bend (I)
45-deg wye
90-deg elbow or 1/4 bend (I)
Footnotes for Table 2.3.1

(I) Short radius fittings shall be permitted only in drain piping for individual fixtures.
(2) Long radius fittings shall not be used to connect fixture trap arms to vertical drain and vent piping.

FROM FIXTURES
UPSTREAM
/"
SHORT PATTERN
(Section2.3.1) --
LONG PATTERN
(Section 2.3.1) '"
/" SHORT PATTERN
"- FROM FIXTURES UPSTREAM
ISOMETRIC VIEW
NOTES:
1. Short pattern fittings are permitted in drain piping for individual fixtures.
2. Long pattern fittings are not permitted to connect fixture trap arms to vertical drain and vent piping
Figure 2.3.1 - D
USE OF SHORT AND LONG PATTERN DRAINAGE FITTINGS
2.3.2 Double Pattern Fittings

The uses for double pattern drainage fittings shall be the same as for single pattern fittings in Table 2.3.l.
EXCEPTION: Double sanitary tees and crosses shall not be used to connect blowout fixtures, back-outlet
waterclosets,and fixturesor applianceshavingpumpeddischarge. See Figure 2.3.2
DOUBLEFIXTUREFITTING- ENLARGED
EJ?
DOUBLE COMBINATION WYE & 1/8 BEND
CHAMBERTO PREVENTCROSS-FLOWFROM HORIZONTAL DRAINAGE TO
ONE FIXTURETO ANOTHER VERTICAL DRAINAGE
NOTES:
1. Double pattern fittings can be used in horizontal and vertical piping.
2. Long pattern fittings are not permitted to connect fixture trap arms to vertical drain and vent piping
Figure 2.3.2
DOUBLE PATTERN DRAINAGE FITTINGS

2.3.3 Back-to-Back Fixtures
Stack fittings, including carriers, for back-outlet fixtures installed back-to-back shall be either the wye pattern,
incorporate baffles within the drainage fitting, or otherwise be designed to prevent crossflow or mixing of the
discharges from the two fixtures prior to the change in direction. See Figure 2.3.3
VERTICAL
STACK
TOPVENT! INLET
t BAFFLEB
FROM i' ETWEEN INLETS

-Jy--- ii
qflf
FIXTURE II
~ I'-- FROM
FIXTURE
t
STACK
OUTLET
PARTA
VENTEDCLOSETCROSS
.
WITH 2 TOP VENT
VERTICAL HORIZONTAL
STACK BRANCH
FROM FROM FROM FROM
FIXTURE -Jy--- ~ I'-- FIXTURE FIXTURE -Jy--- ~ I'--

FIXTURE
(Note3)
(Note 2) "'J' (Note2) (Note3) "'J'
VERTICAL HORIZONTAL
STACK BRANCH
PARTB PARTC
DOUBLECOMBINATIONWYE & 1/8 BEND DOUBLECOMBINATIONWYE & 1/8BEND
HORIZONTAL- TO - VERTICAL HORIZONTAL- TO - HORIZONTAL
NOTES:
materials.
2. In Part 8, the fixtures must be vented prior to connection to the stack.
3. In Part C, if not battery vented, the fixtures must be individually vented prior to connection to the
branchdrain.
Figure 2.3.3
PREVENTING CROSSFLOW BETWEEN BACK-TO-BACK BACK-OUTLET FIXTURES

2.4 FITTINGS AND CONNECTIONS IN DRAINAGE SYSTEMS
2.4.1 Prohibited Fittings

No running threads or saddles shall be used in the drainage or vent system. No drainage or vent piping shall
be drilled, tapped, burned or welded.
2.4.2 Heel or Side-Inlet Bends

A heel or side-inlet quarter bend shall not be used as a dry vent when the inlet is placed in a horizontal
position or any similar arrangement of pipe or fittings producing a similar effect.
EXCEPTION: When the entire fitting is part of a dry vent arrangement system the heel or side-inlet bend
shall be acceptable. See Figures 2.4.2-A and 2.4.2-B
VENT
VENT
FIXTURE
DRAIN
~ PROHIBITED IF NOT ~ PROHIBITED IF NOT

A WET VENT A WET VENT
Figure 2.4.2 - A
HORIZONTAL HEEL OR SIDE INLET VENT CONNECTION
DRY VENT IS ACCEPTABLE

IF HEEL INLET IS VERTICAL
Figure 2.4.2 -B
VERTICAL HEEL INLET VENT CONNECTION
2.4.3 Obstruction to Flow
No fitting, connection, device, or method of installation which obstructs or retards the flow of water, wastes,
sewage, or air in the drainage or venting systems in an amount greater than the normal frictional resistance to

- --
flow, shall be used unless it is indicated as acceptable in this Code. The enlargement of a three-inch closet
bend or stub to four inches shall not be considered an obstruction, provided the horizontal flow line or invert is
continuous without forming a ledge or shoulder.
Comment #J: This Section does not prohibit double hub fittings for soil pipe installations since they
create no more restriction toflow that would be encountered with a hubless coupling or similar fitting.
Comment #2: Failure to ream or deburr drainage piping constitutes an obstruction toflow.
2.4.4 Prohibited Joints

Cement mortar joints are prohibited.
EXCEPTION: When used for repairs and/or when used for connections to existing lines constructed with
suchjoints.
2.5 HEALTH AND SAFETY

Where a health or safety hazard is found to exist on a premise, the owner or his agent shall be required to make
such corrections as may be necessary to abate such nuisance, and bring the plumbing installation within the
provisions of this Code.
2.6 TRENCHING, BEDDING, TUNNELING AND BACKFILLING
2.6.1 Trenching and Bedding

a. Trenching and excavation for the installation of underground piping shall be performed in compliance
with occupational safety and health requirements. Trenches shall be of sufficient width to permit proper
installation of the pipe. Where shoring is required, additional allowance shall be made in the width of the
trench to provide adequate clearance.
b. A firm, stable, uniform bedding shall be provided under the pipe for continuous support. Bell holes shall
be provided for joints in bell and spigot pipe and for other joints requiring such clearance. Blocking shall not be
used to support the pipe.
c. The trench bottom may provide the required bedding when adequate soil conditions exist and when
excavated to the proper depth and grade. Where trenches are excavated to depths below the bottom of the
pipe, bedding shall be added beneath the pipe as required. Such bedding shall be of clean sand, gravel, or
similar select material that is compacted sufficiently to provide the support required under 2.6.I.b.
d. Where rock is encountered in trenching, it shall be removed to a depth of not less than 6 inches below
the bottom ofthe pipe and bedding shall be added as required under 2.6.1.c. The pipe shall not rest on rock at
any point, includingjoints.
See Figures 2.6.1-A and 2.6.1-B. Also Sections 2.6.2, 2.6.3, and 2.6.4
2003 National Standard Pumbing Code-lIIustrated 71

-- - ---n__- --- - -- ---
GRADE GRADE
~~~<><~<><&:~~~~~~%%~~~~~<><&:~~~~~~~<><&:
- - - - - - -
- --- BACKFILL
- - - - - - - - - -
~, / " 0] . / / / / ,0] ~
/ / / / . / / / / / // / / / / / / / / / / '-- SOIL BEDDING
~
1=111=1 (1::::511=-'1~=1II:;I:r~ I1=1 II=--' . ,-=111=1 fi::::511=1~=1II:;I:r=
:111=111=111=11.-==111=111=111=111-='111=111=111=111=111=111=111=11
~II~II~II~I~II~II~':~II~II~II~III~I~II~II~II~
SOIL BEDDING PIPE BELLS OR COUPLINGS
NOTES:
1, The soil under the pipe must be stable, Unstable bedding may damage the pipe, fittings, or joints
when settlement occurs.
2. The side-fill should be shoveled under the pipe to make sure that there are no voids in the side-fill.
Figure 2.6.1 - A
UNDERGROUND PIPING BEDDED ON SOIL
GRADE GRADE
~~~~~~~%~%~~~~~~~~~~~~%<&:~~~~~
- - - - - - - -
- - - - - - - - - - --- BACKFILL
- - - - - -
SAND OR GRAVEL
BEDDING
SAND OR GRAVELBEDDING
NOTES:
1. Unstable bedding may damage the pipe, fittings, or joints when settlement occurs.
2. The side-fill should be shoveled under the pipe to make sure that there are no voids in the side-fill.
Figure 2.6.1 - B
UNDERGROUND PIPING BEDDED ON SAND OR GRAVEL
2.6.2 Side-fill
The haunch areas adjacent to the pipe between the bottom of the pipe and its horizontal centerline shall be
filled with a clean coarse-grain material such as sand, gravel, or soil. Such side-fill shall be placed by hand,
extending to the sides of the trench, and be compacted to provide lateral support for the pipe. See Figure
2.6.1-A and 2.6.1-B

2.6.3 Initial Backfill
After installation of the side-fill, the trench shall be backfilled to a level not less than 2 feet above the top of
the pipe. Backfill material shall be sand, gravel, or loose soil that is free of rocks and debris. Maximum
particle size shall be 1-112inches. Backfill shall be placed in not more than 6-inch layers, each tamped and
compacted. Heavy compacting equipment shall not be used for the initial backfill. See Figure 2.6.3
1 c- c. . C:::L::Cc::
- . . - . . - . . - . . - ~:~:
. . - . . - :6:)c
..- ..c
- c
. .c
- c
..c
- c
. . c,
- . FILL
LAYERSUNTIL
TAMPED TWO
IN6'
24" ~
-.. :-: -~ .:-:. -~ :-:
.. ~ . . :: . . ::
L
~
- :-: - :-: - :-:
..-..-..-..-..-..-..-..-..-..-..-.-...
..-..-..-..-..-..-..-..-..-..-..-..-...
. . .- . :-:
. . .- . :-:
. . .- . :-:
. . .- . :-:
. . .- . :-:
. . .- . :-:
. . .-..: FEET OF EARTH
COVERS THE PIPE
1f~ - . . - . "OJ . - . . - . . - . . - . . - . . - . '1] - . . - . . - .~
NOTES:
1. The side-fill adjacent to the pipe must be backfilled and tamped to the top of the pipe.
2. The initialbackfillmust be placed in6"tamped layers. The use of heavy compacting equipment is
prohibited.
3. The initial backfill material must be sand, gravel, or loose soil from the excavation that is free from
rocks and debris. Broken concrete, frozen earth, and other solid materials may damage the pipe
from point loads.
4. After the pipe is covered with 2 feet of tamped initial backfill, the final backfill to grade can be
compacted with heavyequipment.
Figure 2.6.3
TYPICAL BACKFILLING PROCEDURE
2.6.4 Final Backfill

The trench shall be backfilled from the top of the compacted initial backfill to finish grade using suitable
material. Heavy compacting equipment may be used for the final backfill. See Figure 2.6.3
2.6.5 Tunneling
When pipe is installed in a dug or bored earth tunnel, the space around the pipe between the pipe and the wall
ofthe tunnel shall be completely filled with packed concrete or grout. When pipe is installed in ajacked-in-
place conduit or sleeve, the space around the pipe between the pipe and the inside of the conduit or sleeve
shall be sealed in an approved manner in accordance with Section 2.12.d.
2.6.6 Underground Plastic Pipe

a. Underground plastic pipe shall be installed in accordance with the requirements of Section 2.6.
EXCEPTIONS:
I. The maximum particle size in the side-fill and initial backfill shall be not more than 1/2-inch for pipe 6"
size and smaller, and 3/4-inch for pipe 8" and larger.
2. For water service piping, refer to ASTM D2774, Standard Practice for Underground Installation
of Thermoplastic Pressure Piping.
2003 National Standard Pumbing Code-l!Iustrated 73

-m_. m__- - - -
3. For gravity-flow drainage pipe, refer to ASTM 02321, Underground Installation of Thermoplastic
Pipe for Sewers and Other Gravity-jlow Applications.
b. An insulated copper tracer wire or other approved conductor shall be installed adjacent to underground
non-metallic water service piping and non-metallic force mains, to facilitate finding. One end shall be brought
above ground inside or outside the building wall. The tracer wire for the water service shall originate at the
curb valve required in Section 10.12.1. The tracer wire for the force main shall originate at the final point of
disposal. The tracer wire shall not be less than 18 AWG insulated. The insulation shall not be yellow in color.
2.6.7Underground Copper Piping

Underground copper piping shall be installed in accordance with the requirements of Section 2.6.
EXCEPTION: The maximum particle size in the side-fill and initial backfill shall be not more than I/2-inch for
pipe 6" size and smaller, and 3/4-inch for pipe 8" and larger.
2.6.8 Safety Precautions

Rules and regulations pertaining to safety and protection of workers, other persons in the vicinity, and neigh-
boring property shall be adhered to where trenching or similar operations are being conducted.
2.6.9 Supervision
Where excavation, bedding or backfilling are performed by persons other than the installer of the underground
piping, the pipe installer shall supervise the bedding, side-fill, and initial backfill, and shall be responsible for its
conformance to this Code.
2.6.10 Trenchless Pipe Replacement Systems

Trenchless replacement of water and sewer piping shall be performed using equipment and procedures
recommended by the equipment manufacturer. Where underground piping beneath paved surfaces or
concrete floor slabs is replaced by this method, the manufacturer's recommendations for the specific condi-
tions shall be used. Approved mechanical couplings shall be used to make the connections between new and
existing piping.
Comment: When piping beneath paving or concrete floors is replaced by the trench less method, there
must be sufficient distance above the pipe to prevent cracking the paving or floor slab when the pipe
being replaced bursts.
2.7 SAFETY
Any part of a building or premise which is changed, altered, orrequired to be replaced as a result of the installa-
tion, alteration, renovation, or replacement of a plumbing system, or any part thereof, shall be left in a safe, non-
hazardous condition.
2.8 INSTALLATION PRACTICES

Plumbing systems shall be installed in a manner conforming to this Code and industry installation standards.

2.9 PROTECTION OF PIPES
2.9.1 Breakage
Pipes passing under or through walls shall be protected from breakage. Any plumbing pipe passing under a
footing or through a foundation wall shall be provided with a relieving arch, or as otherwise approved by the
Authority Having Jurisdiction.
EXCEPTION: Sleeves shall not be required for pipes passing through drilled holes. Drilled holes shall provide
\;Sinch minimum clearance around the pipe.
2.9.2 Corrosion
Pipe subject to corrosion by passing through or under corrosive fill, such as, but not limited to, cinders, con-
crete, or other corrosive material, shall be protected against external corrosion by protective coating, wrap-
ping, or other means which will resist such corrosion.
Comment #1: Soil samples should be taken to assure that the soil will not corrode the pipe. Wrappings
and coatings reduce contact corrosion, but cathodic protection may be required where stray electric
currents exist.
Comment #2: Job site debris should not be allowed in the backfill for piping trenches. Material such as
metal cans, metal studs, and gypsum board may chemically react with some types of pipe .
2.9.3 Cutting or Notching

Any structural member weakened or impaired by cutting, notching, or otherwise, shall be reinforced, repaired
or replaced, so as to be left in a safe structural condition in accordance with the requirements of the Building
Code or as required by the proper Authority Having Jurisdiction.
2.9.4 Penetration
a. Plastic and copper piping run through framing members to within one inch of the edge of the framing
shall be protected by steel nail plates not less than 18 gauge. Where such piping penetrates top plates or sole
plates ofthe framing, the nail plate shall extend at least two inches below top plates and two inches above
sole plates.
b. Where plastic and copper piping runs through metal framing members, it shall be protected from
abrasion caused by expansion and contraction of the piping or movement ofthe framing.
2.10 EXCLUSION OF MATERIALS DETRIMENTAL TO THE

SEWAGE SYSTEM
2.10.1 General
No material shall be deposited into a building drainage system or sewer which would or could either obstruct,
damage, or overload such system; which could interfere with the normal operation of sewage treatment
processes; or which could be hazardous to people or property. This provision shall not prohibit the installation
of special waste systems when approved by the Authority Having Jurisdiction.

2.10.2 Industrial Wastes
Waste products from manufacturing or industrial operations shall not be introduced into the public sewer
system until it has been determined by the Authority Having Jurisdiction that the introduction thereof will not
cause damage to the public sewer system or interfere with the functioning of the sewage treatment plant.
Comment: Where industrial wastes will be created, the facility should provide the following information
to the Authority Having Jurisdictionfor the sewerage system: (1) the quantity of water and waste
material that will be discharged into the sewer system, (2) the industrial processes that create the waste,
(3) the composition and concentration of the chemicals in the waste, (4) the water supply demandfor the
facility, and (5) the intended design of the pre-treatment or neutralizing system for the wastesprior to its
discharge into the sewer system.
2.11 RESERVED
2.12 SLEEVES
a. All piping passing through concrete walls, floors, slabs, masonry walls and other corrosive materials, shall be
provided with sleeves for protection from any harmful or caustic reaction.
b. Sleeves shall be sized so there is a minimum of 1/2-inch clearance around the pipe and/or insulation.
c. Piping through concrete or masonry walls shall not be subject to any load from building construction.
d. The annular space between sleeves and pipes shall be filled or tightly caulked with coal tar, asphaltum
compound, lead, or other material found equally effective and approved as such by the Authority Having Jurisdic-
tion.
e. All penetrations of construction required to have a fire resistance rating shall be protected in accordance
with the applicable building regulations.
f. Where piping passes through concrete, masonry, or other corrosive material, sleeves shall be provided
where necessary to prevent any harmful or caustic reaction caused by contact between the piping and the building
construction.
See Figure 2.12
--~
SLEEVE \ ~i SLEEVESMUST BE SIZED
SO THERE IS A MINIMUM OF 1/2 INCH
to
,
PACKING MATERIA L
\ I
/ \
'
'
I
CLEARANCE AROUND PIPE
\
,
(
\ \
Ii , , ~
\ )
NOTES:
1. The sleeve must be sealed where necessaryto prevent the entrance of ground water into the
building.
Figure 2.12
A PIPE SLEEVE THROUGH A FOUNDA nON WALL

uu-u-
2.13 RATPROOFING
2.13.1 Strainer Plates

Strainer plates on drain inlets shall be designed and installed so that no opening is greater than 1/2 inch in least
dimension.
2.13.2 Meter Boxes

Meter boxes shall be constructed in such manner that rats cannot enter a building by following the service
pipes from the box into the building.
Comment: Meter boxes are usually controlled by the local water utility.
2.13.3 Openings for Pipes

In or on buildings where openings have been made in walls, floors, or ceilings for the passage of pipes, they
shall be closed and protected by the installation of approved metal collars securely fastened to the adjoining
structure.
2.14 USED MATERIAL OR EQUIPMENT

Used plumbing material or equipment which does not conform to the standards and regulations set forth in this
Code shall not be installed in any plumbing system.
2.15 CONDEMNED EQUIPMENT

Any plumbing equipment condemned by the Authority Having Jurisdiction because of wear, damage, defects or
sanitary hazards, shall not be used for plumbing purposes.
2.16 FREEZING OR OVERHEATING

The plumbing system shall be protected from freezing or overheating. The following conditions shall be met:
1. Water service piping shall be installed below recorded frost lines. Minimum earth cover shall be-
inches.
2. Minimum earth cover for building sewers shall be - inches.
3. In systems which are used seasonally, water piping shall be installed to be drained.
4. Piping shall be installed so that the contents will not be heated due to close proximity to any heat source or
from direct solar radiation.
5. In areas with seasonal freezing temperatures, all waste and water supply piping in exterior walls and other
areas shall be protected from freezing.
See Figure 2.16

<\"<,
''>. T"y/)V />7/
X INCHES
L0 SEWER
Y INCHES
DISTANCES X AND YARE

GROUND COVER, NOT WATER
TRENCH DEPTH a
NOTES:
1. Referto the adopting ordinance forthis Plumbing Code to determine the minimum required cover for
water service and sewer piping.
2. Locating piping in exterior walls where freezing is possible should be avoided if possible. Thermal
insulation only retards the loss of heat, it does not prevent it.
3. Heat tracing may be required where piping is exposed outdoors or in unheated spaces.
Figure 2.16
DEPTH OF COVER FOR WATER SERVICE AND SEWER PIPING
2.17 PROTECTING FOOTINGS

Trenching parallel to and below the bottom offootings or walls shall not penetrate a 45 plane extending outward
from the bottom comer of the footing or wall, unless the soil type is approved by the Authority Having Jurisdiction
for a different angle of repose. See Figure 2.17
BUILDING WALL,
. <
/\XCAVATION
OTHER STRUCTURAL ;;"
MEMBER OR
COLUMN, :::>;
(""'
'~,:',,>.1
,
SOIL TYPE AND CONDITION

MAY PERMIT OR REQUIRE A
DIFFERENT ANGLE OF REPOSE
NOTES:
1. Check the project design documents to verify that a 45 degree angle of repose is permissible.
2. Consult the project structural engineer if conditions dictate that excavations must be closer
than 45 degrees from the bottom edge offootings.
Figure 2.17
PROTECTING STRUCTURAL FOOTINGS FROM BEING UNDERMINED

__n - ---
2.18 CONNECTIONS TO PLUMBING SYSTEMS REQUIRED

Every plumbing fixture, drain, appliance, or appurtenance thereto which is to receive or discharge any liquid waste
or sewage shall discharge to the sanitary drainage system ofthe building in accordance with the requirements of
this Code.
2.19 CONNECTION TO WATER AND SEWER SYSTEMS
2.19.1 Availability of Public Water and Sewer

The water distribution and drainage systems of any building in which plumbing fixtures are installed shall be
connected to a public water supply and sewer system respectively if the public water supply and/or public
sewer is within - feet of any property line of the premises, or other reasonable distance as determined
by the Authority Having Jurisdiction. See Figure 2.19.1
,. ,/
/"'-
i- \>-~-{;'\-{ ~,oJi>0,o
o~ o~ <><;;..- <::'Ji>y
~~
,,0~~-<,.
".-0'<
K.- "'-(ltV~.....
0~
-<,.'0K.- "'-.....
PUBLIC WATER SUPPLY
PUBLIC SEWER
NOTES:
1. Refer to the adopting ordinance for this Plumbing Code to determine the distance from which
properties must be connected to public water and sewer systems.
2. Connections to public water and sewer systems are more desirable than private systems, from the
standpoint of public health and convenience.
Figure 2.19.1
REQUIRED CONNECTION OF PROPERTIES
TO PUBLIC WATER AND SEWER SYSTEMS
2.19.2 Private Systems

Where either a public water supply or sewer system, or both, are not available, a private individual water
supply or individual sewage disposal system, or both, shall be provided, and the water distribution system and
drainage system shall be connected thereto. Such private systems shall meet the standards for installation and
use established by the Health Department or other agency having jurisdiction. (See Chapters 16 and 17.) See
Figure 2.19.1. Also the definitions of "Private Sewage Disposal System" and "Private Water
Supply" .
Comment: Plumbing in buildings connected toprivate water or sewage systems must comply with all
applicable requirements of this Code or the Authority Having Jurisdiction.

2.20 WASHROOM & TOILET ROOM REQUIREMENTS
2.20.1 Light and Ventilation

Light and ventilation shall be provided as required by other applicable codes.
2.20.2 Location ofPiping and Fixtures

Piping, fixtures, or equipment shall not be located in such a manner as to interfere with the normal operation
of windows, doors, or other exit openings.
2.21 PIPING MEASUREMENTS

Except where otherwise specified in this Code, all measurements shall be made to the center lines of the pipes.
2.22 WATER CLOSET CONNECTIONS

a. Three-inch bends may be used on water closets or similar connections provided a 4-inch by 3-inch flange is
installed to receive the closet fixture horn.
b. Four-inch by three-inch closet bends shall be permitted.
See Figures 2.22
i4"NOM'1
i4"NOM'1
1 ---1 3"NOM.I--
r-FiNISHEDFLOOR f3"NOM.
~
NOTES:
1. Reducing fixturedrains forwater closets from4"to 3"is permissible.
Figure 2.22
WATER CLOSET DRAIN CONNECTIONS
2.23 DEAD ENDS

Dead ends shall be avoided in the installation and removal of any part of a drainage system.
EXCEPTION: Where necessary to extend a cleanout to make it accessible. See Figure 2.23 and the defini-
tion of "Dead End".
Comment: Rough-ins for future fIXtures are not considered dead ends if the piping is accessible and can
be cleared of any blockages when the future fIXtures are installed.

m ---
2.24 TOILET FACILITIES FOR WORKERS

Suitable toilet facilities shall be provided and maintained in a sanitary condition for the use of workers during
construction. (See Table 7.21.1.)
2.25 FOOD HANDLING ESTABLISHMENTS

Food or drink shall not be stored, prepared or displayed beneath overhead sewer or drain pipes unless such pipes
are protected against leakage or condensation reaching the food or drink as described below for new construction.
In newly constructed or remodeled establishments, soil or drain pipes located over food preparation, storage,
display or serving areas are undesirable. Where building design requires that soil or drain pipes be located over
such areas, the installation shall be made with the least possible number of joints and shall be installed so as to
connect to a vertical stack at the nearest wall or vertical building support and the construction shall be performed
as follows:
1. All openings through floors over such areas shall be provided with sleeves securely bonded to the floor
construction and projecting not less than 3/4 inch above top of the finished floor with space between sleeve and
pipe or duct sealed.
2. Floor and shower drains installed above such areas shall be equipped with integral seepage pans.
3. Plumbing fixtures in rooms located above such areas shall be ofthe wall mounted type except bathtubs. Tubs
shall have waste and overflow connections made above floor and piped to the trap below the floor. Connections
through floors and traps shall conform with all other provisions ofthis regulation. No floor openings, other than
sleeve for waste pipe, will be permitted for tubs.
4. All other soil or drain pipes shall be of an approved material as listed in Table 3.1.3 and Section 11.1. All
materials shall conform to established standards. Cleanouts shall be extended through the floor construction above.
5. Soil and drain pipes located above such areas shall be subjected to a standing water test of not less than 25
feet.
6. Piping subject to operation at temperatures that will form condensation on the exterior of the pipe shall be
thermally insulated.
7. Where pipes are installed in ceilings above such areas, the ceiling shall be of the removable type, or shall be
provided with access panels in order to form a ready access for inspection of piping.
8. In lieu of the above, any other method may be approved by the Authority Having Jurisdiction which does not
conflict with applicable health codes.
9. The installation of vacuum collection systems in buildings where food is prepared, stored or displayed shall be
permitted provided that the system is under constant vacuum. The piping shall be smooth bore and long pattern
fittings shall be used. Bracing shall be per the manufacturer's instructions.
See Figures 2.25 - A and 2.25 - B

FILLER MATERIAL - WATERTIGHT
AND SEALED ACCORDING TO
FIRE AND BUILDING CODES
NOT LESS THAN
~ 3/4" ABOVE FLOOR
. .
t'-:i<t. ;':';'
NOTES:
1. The 3/4" extended sleeve prevents spillage on the floor above from leakingdown into the food
handling area and contaminating the food products.
Figure 2.25 - A
A PIPE PENETRAnON OF A FLOOR ABOVE A FOOD HANDLING AREA
WATER SUPPLY NOT SHOWN
LAVATORY
WALL HUNG
WATER CLOSET
BATHTUB
< SEE FIGURE 2.25A
,LV
PIPING IS IN CEILING SPACE

PIPING MUST BE ACCESSIBLE
NOTES:
1. All pipe penetrations through the floor above must have extended pipe sleeves. See Figure 2.25 - A.
The number offloor penetrations should be minimized.
2. Floor -outlet water closets are not permitted above a food handling area.
3. Bathtubs and showers must have above-the-floorwaste outlets with piping extended to a point
where an extended pipe sleeve can be installed.
4. Piping run in a ceiling space above a food handling area must be fully accessible.
Figure 2.25- B
PLUMBING FIXTURES ABOVE A FOOD HANDLING AREA

. Chapter 3
Materials
3.1 MATERIALS
3.1.1 Minimum Standards
The standards cited in this chapter shall control all materials, systems, and equipment used in the construction,
installation, alteration, repair, or replacement of plumbing or drainage systems or parts thereof.
EXCEPTIONS:
(1) The Authority Having Jurisdiction shall allow the extension, addition to or relocation of existing water,
soil, waste, drainage and vent pipes with materials oflike grade or quality as permitted in Section 3.12.2.
(2) Materials not covered by the standards cited in this chapter may be used with the approval of the
Authority Having Jurisdiction as permitted in Section 3.12.2.
3.1.2 GeneralRequirements
a. Materials, fixtures, or equipment used in the installation, repair or alteration of any plumbing system
shall conform at least to the standards listed in this chapter, except as otherwise approved by the Authority
Having Jurisdiction under the authority contained in Section 3.12.
b. Materials installed in plumbing systems shall be so handled and installed as to avoid damage so that the
quality of the material will not be impaired.
c. No defective or damaged materials, equipment or apparatus shall be installed or maintained. (See
Sections 2.14 and 2.15)
d. All materials used shall be installed in strict accordance with the standards under which the materials
are accepted and approved, including the appendices of the standards, and in strict accordance with the
manufacturer's instructions. Where the provisions of material standards or manufacturer's instructions
conflict with the requirements of this Code, this Code shall prevail.
3.1.3 Standards Applicable to Plumbing Materials

A material shall be considered approved if it meets one or more of the standards cited in Table 3.1.3, and in
the case of plastic pipe, also the listed standard of the NSF International. Materials not listed in Table 3.1.3
shall be used only as provided for in Section 3.12.2 or as permitted elsewhere in this Code.
Note: Abbreviations in Table 3.1.3 refer to the following organizations:
2003 National Standard Pumbing Code-lllustrated 83

AHAM Association of Home CSA Canadian Standards
Appliance Manufacturers Association
111 19thStreet, NW, Ste. 402 178 Rexdale Blvd., Rexdale
Washington, DC 20036 Toronto, ON M9W-IR3
CANADA
ANSI American National
Standards Institute FS Federal Specification
Fourth Floor General Services Administration
25 West 43rd Street Specification Section -
New York, NY 10036 Room 6039
7th & D Streets
ASME American Society of Washington, DC 20407
Mechanical Engineers
Three Park Avenue FM Factory Mutual Engineering
New York, NY 10016-5990 and Research
1151 Boston Providence Turnpike
ASSE American Society of Norwood, MA 07062
Sanitary Engineering
901 Canterbury Rd., Suite A IAPMO International Association of
Westlake, OH 44145 Plumbing and Mechanical
Officials
ASTM American Society of 20001 East Walnut Dr. South
Testing and Materials Walnut, CA 91789
100 Barr Harbor Drive
West Conshohocken, PA 19428-2959 MSS Manufacturing
Standardization Society
AWS American Welding Society 127 Park Street NE
550 Northwest Leleune Road Vienna, VA 22180
Miami, FL 33126
NSF NSF International
AWWA American Water Works 789 Dixboro Road
Association Ann Arbor, MI 48105
6666 West Quincy Avenue
Denver, CO 80235 PDI Plumbing and Drainage
Institute
CISPI Cast Iron Soil Pipe Institute 45 Bristol Drive
Suite419 South Easton, MA 02375-1916
5959 ShallowfordRoad
Chattanooga, TN 37421 UL Underwriter's Laboratory
333 Pfingsten Road
Northbrook,IL 60062
84 2003 National Standard Pumbing Code-l!Iustrated

3.1.4 Identification of Materials
Materials shall be identified as provided in the standard to which they confonn.
3.2 SPECIAL MATERIALS
3.2.1 Copper and Brass

Sheet and tubular copper and brass for the following uses shall weigh not less than:
a. General use - 12 oz. per square foot
b. Flashing for vent pipes - 8 oz. per square foot
c. Trap and tailpiece fittings - B&S 17 gauge (.045 in)
3.2.2 Lead
See Table 3.1.3. Sheet lead shall be not less than the following:
a. Shower pans-not less than 4 pounds per square foot (pst) and be coated with an asphalt paint or
equivalent. /
b. Flashings of vent tenninals-not less than 3 pounds per square foot (pst).
c. Lead bends and lead traps shall not be less than 1/8" wall thickness.
3.2.3 Plastic
a. Trap and tailpiece fittings-minimum 0.062" wall thickness.
b. Piping- see specific application - Sections 3.4 to 3.11.
c. Shower pans-approved plastic sheeting material.
Comment: Plastic shower pans should not be covered with asphalt unless recommended by the manu-
facturer.
3.3 FITTINGS, FIXTURES, APPLIANCES & APPURTENANCES
3.3.1 Drainage Fittings

See Sections 2.3 and 2.4 for fittings and connections in drainage systems.
3.3.2 Clean out Plugs and Caps

a. Cleanout plugs shall be of brass, plastic, stainless steel, or other approved materials and shall have
raised or countersunk square heads, except that where raised heads will cause a tripping hazard, countersunk
heads shall be used.
b. Cleanout caps shall be of brass, plastic, reinforced neoprene, cast-iron, or other approved material and
shall be readily removable.
See Figure 3.3.2

, ,
f J...JlI
I I
I I
I I
I I
I I
I I
I I
I
COUNTERSUNK HEAD PLUG RAISED HEAD PLUG
Figure 3.3.2
CLEANOUT PLUGS
3.3.3 Fixtures
a. Plumbing fixtures shall be constructed from approved materials having smooth, non-absorbent surfaces
and be tree from defects, and except as permitted elsewhere in this Code, shall conform to the standards
cited in Table 3.1.3.
b. Materials for special use fixtures not otherwise covered in this Code shall be constructed of materials
especially suited to the use for which the fixture is intended.
See Chapter 7 for the requirements for specific fixtures
Comment #1: The standards for plumbing fixtures that are listed in Table 3.1.3 reflect consensus
agreement between manufacturers, industry representatives, and consumer groups.
Comment #2: Slip resisting surfaces in bathtubs and showers do not constitute a violation of the require-
mentfor smooth surfaces.
3.3.4 Floor Flanges and Mounting Bolts

a. Floor flanges for water closets or similar fixtures shall be not less than 118"thick for brass, 1/4" thick
and not less than 1-1/2" caulking depth for cast-iron or galvanized malleable iron. Approved copper and plastic
flanges may be used.
b. If of hard lead, they shall weigh not less than lib. 9 oz. and be composed of lead alloy with not less
than 7.75 percent antimony by weight. Flanges shall be soldered to lead bends or shall be caulked, soldered, or
threaded into other metal.
c. Closet screws and bolts shall be brass.
d. The top ofthe closet flange shall be installed not to exceed 1/4" above the finished floor.
3.3.5 Flush Pipes and Fittings

Flush pipes and fittings shall be of nonferrous material. When of brass or copper tube, the material shall be at
least 0.0313" in thickness (No. 20 U.S. gauge).
3.3.6 Reserved
3.3.7 Interceptors
Interceptors shall meet the requirements of Chapter 6.
86 2003 National Standard Pumbing Code-I//ustrated

3.3.8 Pressure Tanks and Vessels
a. Hot water storage tanks shall meet construction requirements of ASME, AGA or UL as appropriate.
(See Table 3.1.3)
b. Storage tanks less in volume than those requirements specified by ASME shall be of durable materials
and constructed to withstand 125 p.s.i. with a safety factor of2.
3.3.9 Roof Drains

Roof drains shall be of cast-iron, copper, lead, or other approved corrosion-resisting materials. See Section
13.5.1
3.3.10 Safety Devices for Pressure Tanks

Safety devices shall meet the requirements ofthe American National Standards Institute, American Society
of Mechanical Engineers, or the Underwriters Laboratories. Listing by Underwriters Laboratories, American
Gas Association or National Board of Boiler and Pressure Vessel Inspectors shall constitute evidence of
conformance with these standards. Where a device is not listed by any of these, it shall have certification by
an approved laboratory as having met these requirements. (See Section 10.16.)
3.3.11 Septic Tanks

a. Plans for all septic tanks shall be submitted to the Authority Having Jurisdiction for approval. Such plans
shall show all dimensions, reinforcing, structural calculations and such other pertinent data as may be re-
quired.
b. Septic tanks shall be constructed of sound durable materials, not subject to excessive corrosion or decay
and shall be watertight. (See Sections 16.6.5 and 16.6.6.)
3.3.12 Carriers and Supports

Carriers and supports for plumbing fixtures shall comply with ASME A112.6.1, ASME A 112.6.2or ASME
AI12.19.12.
3.4 POTABLE WATER PIPING
3.4.1 Plastic Piping

Plastic piping materials used for the conveyance of potable water shall comply with NSP 14 and be marked
accordingly.
3.4.2 Water Service Piping

Water service piping to the point of entrance into the building shall be of materials listed in Table 3.4. and shall
be water pressure rated not less than 160 psig at 73P.
Comment: The manufacturer's markings on plastic water servicepipe must indicate that it is suitablefor
160 psig @ 73F.
3.4.3 Water Distribution Piping

Water piping for the distribution of hot or cold water within buildings shall be of materials listed in Table 3.4.
and shall be water pressure rated for not less than 100 psig at 1800P. Plastic piping used for hot water
distribution shall be installed in accordance with the requirements of Section 10.15.8.

NOTE: The working pressure rating for certain approved plastic piping materials varies depending on pipe
size, pipe schedule and methods of joining. (See Appendix B.)
3.4.4 Fittings
Fittings for water supply piping shall be compatible with the pipe material used.
3.4.5 Material Ratings and Installation

a. Piping used for domestic water shall be suitable for the maximum temperature, pressure, and velocity
that may be encountered, including temporary increases and surges.
b. Relief valve temperature and pressure relief settings shall not exceed the approved standard rating for
hot and cold water distribution piping.
c. Pipe and fittings shall be installed in accordance with the manufacturer's installation instructions and the
applicable material standards, recognizing any limitations in use.
Comment: Refer to the standards listed in Table 3.1.3 to determine the pressure and temperature ratings
of the various piping materials.
3.4.6 Limit on Lead Content

a. Materials used in the potable water supply system, including faucets and valves, shall not contain more
than 8 percent lead.
b. Drinking water system components shall comply with the lead leachate requirements as specified for
covered products ofNSF International 61.
See Section 4.2.4 for the limit on lead in solder filler metal
Comment: The limitof8% lead is based on the EPA Safe Drinking Water Act. Generally,fLXturefitting
castings do not exceed 7% lead.
3.5 SANITARY DRAINAGE PIPING
3.5.1 Aboveground Piping -Soil,Waste and Indirect Waste

Aboveground soil and waste piping within buildings shall be of materials listed in Table 3.5.
3.5.2 Underground Building Sanitary Drains

Underground building drains and other underground sanitary drain and waste piping within buildings shall be of
materials listed in Table 3.5.
3.5.3 Building Sanitary Sewer

Sanitary sewer piping outside of buildings shall be of materials listed in Table 3.5. Joints shall be watertight
and root proof.

a. Pipe and fittings classified by standard dimension ratio that are underground outside of buildings shall be
SDR 35 or heavier (lower SDR number). Pipe and fittings within buildings shall be SDR 26 or heavier (lower
SDR number), except that SDR 35 fittings shall be permitted.
b. Pipe and fittings classified by pipe stiffness that are underground outside of the buildings shall be PS-45
or heavier (higher PS number). Pipe and fittings within buildings shall be PS-I 00 minimum.

3.5.5 VitrifiedClayPipe
Vitrified clay pipe shall be joined using compressionjoints or couplings. Vitrified clay pipe installed under-
ground within buildings shall be extra strength and shall have 12" minimum earth cover.
3.5.6 Fittings
Fittings in drainage systems shall be compatible with the pipe used and shall have no ledges, shoulders, or
reductions which can retard or obstruct flow. Threaded fittings shall be the recessed drainage type.
3.6 VENT PIPING
3.6.1 Aboveground Piping

Aboveground vent piping in buildings serving sanitary, waste, or storm drainage systems shall be of materials
listed in Table 3.6.
3.6.2 Underground Piping

Vent piping installed underground shall be of materials listed in Table 3.6.
3.6.3 PlasticPiping
b. Pipe and fittings classified by pipe stiffness that are underground outside of buildings shall be PS-45 or
heavier (higher PS number). Pipe and fittings within buildings shall be PS-I 00 minimum.
3.6.4 Fittings
Fittings in vent piping shall be compatible with the pipe material used. Where threaded pipe is used, fittings
shall be either the drainage or pressure type, galvanized or black.
3.7 STORM DRAINAGE PIPING
3.7.1 Exterior Gutters and Leaders

Exterior gutters and rain leaders shall be of galvanized sheet metal, aluminum, plastic or other approved
material.
3.7.2 InteriorConductors
Stormwater'drain piping installed aboveground in buildings shall be of materials listed in Table 3.7.
3.7.3 Underground Building Storm Drains

Underground building storm drains and other underground stormwaterpiping within buildings shall be of
materials listed in Table 3.7.
3.7.4 Building Storm Sewer

Building storm sewer piping outside of buildings shall be of materials listed in Table 3.7,

b. Pipe and fittings classified by pipe stiffness that are underground outside of buildings shall be PS-45 or
heavier (higher PS number). Pipe and fittings within buildings shall be PS-l 00 minimum.
3.7.6 VitrifiedClay Pipe

Vitrified clay pipe shall be joined using compression joints or couplings. Vitrified clay pipe installed under-
ground within buildings shall be extra strength and shall have 12" minimum earth cover.
3.7.7 Fittings
Fittings in drainage systems shall be compatible with the pipe used and shall have no ledges, shoulders, or
reductions which can retard or obstruct flow. Threaded fittings shall be the recessed drainage type.
3.8 FouNDATION DRAINS AND SUBSOIL DRAINAGE

Piping for foundation drains and other subsoil drainage shall be of materials listed in Table 3.8.
3.9 AIR CONDITIONING CONDENSATE DRAIN PIPING

Indirect waste piping from air conditioning unit drains to the point of disposal shall be of a material approved for
either potable water, sanitary drainage or storm drainage.
3.10 CONDENSATE DRAINS FROM COMBUSTION PROCESSES

Piping used to convey condensate from combustion processes (such as from flues and chimneys) shall conform to
the equipment manufacturer's instructions.
3.11 CHEMICAL AND SPECIAL WASTE SYSTEMS
3.11.1 DrainPiping
Separate drainage systems for chemical wastes shall be of corrosion resistant material approved by the
Authority Having Jurisdiction. Materials acceptable for chemical waste drainage systems include chemically
resistant glass pipe, high silicon content cast-iron pipe, vitrified clay pipe, plastic pipe, plastic lined pipe, Type
316L stainless steel DWV pipe, and lead pipe.
3.11.2 Vent Piping

Vent piping on chemical waste systems shall conform to that required for chemical waste pipe except as may
be otherwise authorized by the Authority Having Jurisdiction, and shall be installed independentlythrough the
roof.
3.12 ALTERNATE MATERIALS AND METHODS
3.12.1 ExistingBuildings
a. Plumbing work performed in existing buildings shall conform to the requirements of this Code, unless
the Authority Having Jurisdiction finds that such conformance would result in an undue hardship.
b. The Authority Having Jurisdiction may grant a variation to the extent necessary to relieve the undue
nature of the hardship.

c. A record, open to the public, shall be kept of each variation granted under this section.
3.12.2 Approval
a. The Authority Having Jurisdiction may approve the use of any material or method not expressly
conforming to the requirements of this Code provided all of the following conditions are met:
1. The material or method is not expressly prohibited by this Code.
2. The material or method is determined to be of such design or quality as to appear suitable for the
proposed use.
3. A record of such approval is kept and shall be available to the public.
3.12.3 Tests
When there is insufficient evidence to verify claims for alternate materials, the Authority Having Jurisdiction
may require tests of compliance as proof of suitability. Such tests shall be made by an approved testing
agency at the expense of the applicant.
3.12.4 TestProcedure
Tests shall be made in accordance with approved standards; but in the absence of such standards, the Au-
thority Having Jurisdiction shall specify the test procedure.
3.12.5 Repeated Tests

The Authority Having Jurisdiction may require tests to be repeated if, at any time, there is reason to believe
that an alternate material no longer conforms to the requirements on which its approval was based.
2003 National Standard Pumhing Code-Illustrated 91

TABLE 3.1.3
STANDARDS FOR APPROVED PLUMBING MATERIALS AND EQUIPMENT
1 Hub & Spigot Cast-Iron Soil Pipe and Fittings: ASTMA 74-98.
2 Hubless Cast-Iron Soil Pipe and Fittings: CISPI 301-00, ASTM A888-98.
,..,
-' Ductile- Iron Pressure Pipe: ASTMA377-95,
ANSI/AWWA CI51/A21.51-96.
4 Ductile- Iron and Gray -Iron Fittings (3" and larger): ANSI!AWWACllO/A21.10-93.
5 Cement-Mortar Lining for Ductile- Iron Pipe and Fittings: ANSI!AWWA CI04/A21.4-1995.
6 Steel Pipe, Galvanized, Welded and Seamless: ASTMA53-00,ANSI!ASME
B36.10-2000.
7 Cast-Iron Threaded Drainage Fittings: ANSI!ASME BI6.12-1991.
8 Cast-Iron Threaded Fittings, Classes 125 and 250: ANSI!ASMEBI6.4-1999.
9 Malleable-Iron Threaded Fittings, Class 150 and 300: ANSI!ASMEBI6.3-1999.
10 Ferrous Pipe Plugs, Bushings, and Locknuts with Pipe Threads: ANSI/ASME BI6.14-1991.
Brass Pipe, Red, Seamless, Standard Sizes: ASTMB43-96.

2 Cast Bronze Threaded Fittings, Classes 125 & 250: ANSI!ASMEBI6.15-1985
(RI994).
-',.., Cast Copper Alloy Pipe Flanges, Class 150,300,400,600,900, 1500,2500,
and Flanged Fittings, Classes 150 and 300: ANSI!ASME 16.24-1991(RI998).
4 Cast Copper Alloy Solder Joint Drainage Fittings - DWV: ANSI!ASME BI6.23-1992.
5 Cast Copper Alloy Solder Joint Pressure Fittings: ANSI BI6.18-1984 (RI994).
6 Copper Drainage Tube (DWV): ASTM B306-96.
7 Copper Pipe, Seamless, Standard Sizes: ASTMB42-96.
8 Copper Pipe, Threadless (TP): ASTM B302-00.
9 Copper Water Tube, Seamless (K, L, M): ASTMB88-99(el).
10 Grooved & Shouldered Joints (split couplings, for copper tube ): ANSI!AWWA C606-87.
11 Wrought Copper and Wrought Copper Alloy Solder Joint Drainage
Fittings-DWV: ANSI/ASMEBI6.29-1995.
12 Wrought Copper and Copper Alloy Solder Joint Pressure Fittings: ANSI!ASMEBI6.22-1995.
13 Lead Pipe, Bends, Traps, Caps and Plugs: FS WW-P-325B (June 9,1976).
14 Stainless Steel DWV Systems: ANSI!ASME AI12.3.1-1993.
15 Cast Copper Alloy Fittings for Flared Copper Tubes: BI6.26-1998.

.,xh+<
!%.i.II.t0IJ.l;jtf; ..&'NcDITJ;J;
I Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (SDR- PR) (1/8" - 12"): ASTM D2282-96a.
2 Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules
40 and 80 (1/8"- 12"): ASTMD1527-96a.
3 Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe Fittings,
Schedule 40 (1/8"- 8"): ASTM D2468-96a.
4 Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain,
Waste, and Vent Pipe and Fittings (1-1/4"- 6"): ASTMD2661-97.
5 Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic
Drain, Waste, and Vent Pipe With a Cellular Core (1-1/4"- 6"): ASTMF628-97.
6 Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and fittings (3 "- 12"): ASTM D2751-96.
7 Acrylonitrile-Butadiene-Styrene (ABS) and Poly (Vinyl Chloride) (PVe)
CompositeSewerPipe(6"-15"): ASTM D2680-95a.
8 Poly (Vinyl Chloride )(PVC) Pressure Pipe for Water (4"- 12"): ANSI! AWW A C900-89 &
Supplement C900a-92.
9 Poly (Vinyl Chloride) (PVe) Plastic Pipe, Schedules 40,80, and
120 (1/8"- 24"): ASTM D1785-96b.
10 Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40;
socket-type (1/8" - 8"): ASTM D2466-97.
11 Poly (Vinyl Chloride) (PVe) Plastic Pipe Fittings, Schedule 80;
socket-type (1/8"- 8"): ASTM D2467-96a.
12 Poly (Vinyl Chloride) (PVe) Plastic Pipe Fittings, Schedule 80,
Threaded (1/8"- 6"): ASTM D2464-96a.
13 Poly (Vinyl Chloride) (PVC) Pressure-Rated Pipe, (SDR Series) (1/8"- 36"): ASTM D2241-96b.
14 Poly (Vinyl Chloride) (PVe) Plastic Drain, Waste, and Vent
PipeandFittings(l-1/4"-12"): ASTM D2665-97a.
15 Poly (Vinyl Chloride) (PVe) Schedule 40 Drainage and DWV
Fabricated Fittings: ASTMF-1866-98.
16 3.25" Outside Diameter Poly (Vinyl Chloride) (PVe)
Plastic Drain, Waste, and Vent Pipe and Fittings: ASTM D2949-97a.
17 Poly (Vinyl Chloride) (PVe) Sewer Pipe and Fittings (2"-6"): ASTMD2729-96a.
18 Poly (Vinyl Chloride) (PVC) Gasketed Sewer Fittings (4"-27"): ASTM F1336-93.
19 Coextruded Poly (Vinyl Chloride) (PVe) Plastic Pipe with a
Cellular Core; Non-Pressure Uses, IPS Schedule 40 (1-1/4"-12"): ASTM F891-96a.
20 Coextruded Poly (Vinyl Chloride) (PVe) Plastic Pipe with a Cellular Core;
Non-Pressure Uses, PS and Sewer/Drain Series (2"-18"): ASTM F891-96a.
21 Type PS-46 Poly(Vinyl Chloride) (PVe) Plastic Gravity Flow Sewer Pipe
andFittings(2"-18"): ASTM F789-95a.
22 Type PSM Poly (Vinyl Chloride)(PVe) SewerPipe andFittings (4 - 15"): II ASTM D3034-97.
23 Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Hot- and Cold- Water
Distribution Systems (3/8"- 2"): ASTMD2846-97.
24 Chlorinated Poly (Vinyl Chloride) (CPVe) Plastic Pipe (SDR-PR) (1/4"- 12"): ASTMF442-97.
25 Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40
and80(l/4"-12"): ASTMF441-97.
26 Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule
80; Socket-type (1/4"- 8"): ASTMF439-97.

27 Chlorinated Poly (Vinyl Chloride) (CPVe) Plastic Pipe Fittings, Schedule 80,
Threaded (1/4"- 6"): ASTMF 437-96b.
28 Polyethylene (PE) Pressure Pipe and Tubing for Water Service (1/2"- 3"): ANSI!AWWAC901-96.
29 Polyethylene (PE) Plastic Pipe (SDR-PR) Based on Controlled Outside Diameter
(1/2"-6"): ASTM D3035-95.
30 Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter
(1/2"- 6"): ASTM D2239-96a.
31 Polyethylene (PE) Plastic Pipe, Schedule 40 (1/2"- 6"): ASTM D21 04-96.
32 Polyethylene (PE) Plastic Pipe, Schedules 40 and 80, Based on Outside Diameter
(1/2"-12"): ASTM D2447 -95.
""
.).) ASTMD2737-96a.
Polyethylene (PE) Plastic Tubing (1/2"- 2"):
34 Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE)
Plastic Pipe and Tubing (1/2"- 48"): ASTMD3261-97.
35 Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe (1/2 "- 4"): ASTM D2609-97.
36 Corrugated Polyethylene (PE) Tubing and Fittings (3 "- 6"): ASTM F405-97.
37 Smoothwall Polyethylene (PE) Pipe for use in Drainage and Waste Disposal
Absorption Fields (3"- 6"): ASTMF810-93.
38 Styrene-Rubber (SR) Plastic Drain Pipe and Fittings (2"- 6"): ASTM D2852-95.
39 Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings;
for Waste Connections (1-1/4", 1-1/2"): ASTMF409-97.
40 Fiberglass Pressure Pipe (I" and larger): ANSI! AWW A C950-95.
41 Fiberglass (GFR) Sewer and Industrial Pressure Pipe (8" and larger): ASTM D3754-96.
42 Fiberglass (G FR) Sewer Pipe (8" and larger): ASTM D3262-96.
43 Fiberglass (GFR) Non-Pressure Pipe Fittings (8" and larger): ASTM D3840-88 (1994).
44 Clay Drain Tile, Perforated (4"- 18"): ASTM C498-95.
45 Vitrified Clay Pipe, Extra Strength, Standard Strength, and Perforated (3" and larger): ASTM C700-97.
46 Concrete Drain Tile (4" and larger): ASTM C412-94.
47 Concrete Sewer, Storm Drain, and Culvert Pipe; non-reinforced (4" and larger): ASTMCI4-95.
48 Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe (12" and larger): ASTM C76-97.
49 Perforated Concrete Pipe (4" and larger): ASTM C444-95.
50 Crosslinked Polyethylene (PEX) Plastic Hot- and Cold-WaterDistribution Systems ASTM F877-99a (with
(3/8" - 2") (SDR 9): ASTM F1807 Metal Insert
Fittings or ASTM F1960
Cold Expansion Fittings).
51 Crosslinked Polyethylene (PEX) Tubing: ASTMF876-99a. (ASTM
F877 with ASTM F1807
Fittings or ASTM F1960
Cold Expansion Fittings.)
52 Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Crosslinked
Polyethylene (PEX) Tubing: ASTMFI807-99.
53 Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked
Polyethylene (PEX) Tubing: ASTM FI960-99.
54 Crosslinked Polyethylene/ Aluminum/Crosslinked Polyethylene (PEX -AL- PEX)
Composite Pressure Pipe (3/8" - I"): ASTM F1281-98a.
55 Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe (3/8"-1 ") ASTM FI282-98a.

56 Metal Insert Fittings for Crosslinked Polyethylene/Aluminum/Crosslinked
Polyethylene (PEX-AL-PEX) and Polyethylene/Aluminum/Polyethylene Composite
Pressure Pipe (PE-AL-PE): ASTMFI974-99a.
57 Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe Systems
(114"- I"): CAN/CSA B137.9-98.
58 Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX -AL- PEX)
Composite Pressure Pipe Systems (1/4" - I"): CAN/CSA B137.10-98.
59 Polyethylene (PE) Plastic Pipe (SDR-PR) Based Upon Outside Diameter: ASTMF714-00
(Minimum SDR values for
TrenchIess systems-see
Tables 3.4. 3.5 and 3.7).
60 Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic
Pipe and Tubing: ASTM D3261-97.
61 Stainless Steel Clamps for Securing SDR 9 Cross-linked Polyethylene (PEX) Tubing
to Metal Insert Fittings: ASTM F 2098-01.
IV. PIPE JOINTS, JOINING MATERIALS, COUPLINGS, GASKETS
I Pipe Threads, Tapered, General Purpose: ANSI!ASME B1.20.1-

1983 (R2001).
2 Liquid and Paste Fluxes for Soldering Applications of Copper and Copper Alloy Tube: ASTMB813-00.
3 Solder Metal: ASTM B32-00.
4 BrazingFillerMetal: ANSI/AWSA5.8-92.
5 Pig Lead: ASTM B29-92 (1997).
6 Grooved and Shouldered Joints (Split Couplings): ANSI/AWWAC606-87.
7 Flexible Transition Couplings for UndergroundPiping Systems: ASTM CI173-97.
8 Rubber Sheet Gaskets: ASTM D1330-85 (1995).
9 Rubber Gasket Joints for Ductile-Iron and Gray-Iron Pressure Pipe and Fittings: ANSI!AWWACll1/
A21.11-95.
10 Rubber Gaskets for Cast-Iron Soil Pipe and Fittings: ASTM C564-95a.
11 Couplings for Hubless Cast-Iron Soil Pipe and Fittings: FM 1680, CISPI 310-97,
ASTM CI277-97.
12 Compression Joints for Vitrified Clay Pipe and Fittings: ASTMC425-97.
13 Rubber Gasket Joints in Circular Concrete Sewer and Culvert Pipe: ASTM C443-94.
14 Elastomeric Seals (gaskets) for Push-OnJoints in Plastic Pipe: ASTM F477-96a.
15 FlexibleElastomeric Sealsfor PlasticPressure Pipe: ASTM D3139-96a.
16 FlexibleElastomeric Sealsfor PlasticDrain andSewerPipe: ASTMD3212-96a.
17 Socket-end IPSPVC Pipe Joints: ASTM D2672-96a.
18 Primers for Solvent Cement Joints in PVC Plastic Pipe and Fittings: ASTM F656-96a.
19 Solvent Cement for Acrylonitrile-Butadiene-Styrene(ABS) Plastic Pipe and Fittings: ASTM D2235-96a.
20 Solvent Cements forPoly (Vinyl Chloride)(PVC)Plastic Piping Systems: ASTM D2564-96a.
21 Solvent Cements for Transition Joints Between Acrylonitrile-Butadiene-Styrene(ABS)
and Poly (Vinyl Chloride)(PVC)Non-Pressure PipingComponents: ASTM D3138-95.
22 Solvent Cements for ChlorinatedPoly (Vinyl Chloride)(CPVC) Plastic Pipeand Fittings ASTMF493-97.
23 Solvent Cements for Styrene-Rubber (SR) Plastic Pipe and Fittings: ASTM D3122-95.
24 Mechanical Couplings for Drain, Waste and Vent Pipe and Sewer Pipe: CSA B602 M90.
20G3 National Standard Pumbing Code-/!/ustrated 95

25 Fittings for Connecting Water Closets to the Sanitary Drainage System: ASME Al 12.4.3-1999.
26 Standard Specificationfor Mechanical Couplings Using ThermoplasticElastomeric
(TPE) Gaskets for Joining Drain, Waste and Vent (DWV), Sewer, Sanitary and Storm
Plumbing Systems for Above and Below Ground Use: ASTMCI461-2000.
27 Non-Reinforced Extruded Tee Connections for Piping Applications: ASTMF2014-00.
1 Bathtubs, Plastic: ANSI Z124.1-1995.

2 Ceramic Plumbing Fixtures, Non- Vitreous: ANSI!ASMEA1l2.19.9M
-1991 (R99) Erata 99.
3 Drains for Prefabricated and Precast Showers: IAPMO PS-4-95.
4 Drinking Fountains and Water Coolers, Self Contained, Mechanically Refrigerated: ANSI!ARI101O-1984,
ANSI/UL399-1992.
5 Enameled Cast- Iron Plumbing Fixtures: ANSI/ASMEAI12.19.1M-
1994with 1998Supplemen
6 Enameled Steel Plumbing Fixtures: ANSI/ASME AI12.19.4M-
1994with 1998Supplemen
7 Floor and Trench Drains: ANSI A1l2.21.1-2001.
8 Lavatories, Plastic: ANSI Z124.3-1995.
9 Roof Drains: ANSI A112.21.2M-1983.
10 Shower Receptors and Shower Stalls, Plastic: ANSIZ124.2-1995.
11 Stainless Steel Plumbing Fixtures (residential design): ANSI!ASMEA112.19.3M.
1987.
12 Vitreous China Plumbing Fixtures: ANSI/ASMEA1l2.19.2M.
1995;ANSI!ASME
A112.19.6-1995.
13 Water Closet Bowls and Tanks, Plastic: ANSIZI24.4-1996; ANSI
/ASME A112.19.6-1995.
14 Whirlpool Bathtub Appliances: ANSI/ASMEAI12.19.7M.
1995.
15 Backflow Prevention Requirements for Fixture Fittings with Hose Connected Single CSA B-125-93;
Movable Outlets: IAPMO PS-49-93.
Plastic: ANSI Z124.9-1993.
16 Urinals, Plastic: ANSI Z124.9-1993
17 Fabricated Stainless Steel Security Water Closets: IAPMOPS61-92.
18 Hydraulic Performance of Water Closets and Urinals: ANSI!ASME A112.19.6-
1995.
19 Wall Mounted and Pedestal Mounted Adjustable and Pivoting Lavatory and Sink
Carrier Systems: ASME Al12.19.12-2000.
20 Plastic Sinks: ANSIZ124.6-97.
21 Prefabricated Spa Shells: ANSIZ124.7-97.
22 Plastic Bathtub Liners: ANSI Z124.8-90.
23 Bathtubs and Whirlpool Bathtubs with Pressure Sealed Doors: ASME A112.19.15-2001.
24 Emergency Equipment and Eyewash Stations:
ANSI Z358.1-1998.

1 Anti-siphon Fill Valves (Ball cocks ) for Gravity Water Closet Flush Tanks: ANSI!ASSE 1002-99.
2 Individual Thermostatic, Pressure Balancing, and Combination Pressure Balancing
and Thermostatic Control Valves for Individual Fixture Fittings ANSI!ASSE 1016-1996
".J
Divertors for Plumbing Faucets with Hose Spray, Anti-Siphon Type, Residential
Application: ASSE 1025-1978.
4 Plumbing Fixture Fittings: ANSI!ASME AI12.18.1-
2000.
5 Flushometers (Pressurized Flushing Devices ): ANSI!ASSE 1037-1990.
6 Laboratory Faucet Vacuum Breakers: ANSI!ASSE 1035-1995.
7 Showers, Hand Held: ANSI!ASSE 1014-1990.
8 Supports for Off- The-Floor Plumbing Fixtures: ANSI!ASMEA112.6.IM-
1988.
9 Trim for Water Closet Bowls, Tanks, and Urinals (dimensional standards): ANSI Al 12.19.5-1979
(RI990).
10 Water Connectors, Flexible Metallic: IAPMOPS-14-89.
11 Water Closet Seats, Plastic: ANSI ZI24.5-1989.
12 Whirlpool Suction Fittings: ANSI!ASMEA112.19.8-
1987.
13 Backflow Prevention Requirements for Fixture Fittings with Hose Connected Single ASMEA112.18.3-1996;
Movable Outlet: CSA B-125-98;
IAPMO PS-49-93.
14 Temperature Actuated Flow Reduction (TAFR) Valves for Individual Fixture Fittings: ASSE 1062-1997.
15 Individual Pressure Balancing In-Line Valves for Individual Fixture Fittings: ASSE 1066-1997.
16 Deck Mounted Bath/Shower Transfer Valves with Integral Backflow Protection: ASMEA112.18.7-I999.
Clothes Washers: ANSI/AHAMHLW-2PR-

1986 (RI992), ANSI!
ASSE 1007-1992.
2 Dishwashing Machines, Commercial: ANSI!UL921-1995,
ANSI!ASSE 1004-1990.
"
.J Dishwashers, Household: ANSI!UL 749-1994,
ANSI/AHAMDW-I-1992,
ANSI!ASSE 1006-1989.
4 Food Waste Grinder Units, Commercial: ANSI!ASSE 1009-1990.
5 Food Waste Disposal Units, Household: ANSI/AHAMFWD-l-
1983 (RI992), ANSI!
ASSE 1008-1989, ANSI!
UL430-1996.
6 Hot Water Dispensers: ASSE 1023-1979.
20G3 National Standard Pumbing Code-Illustrated 97

7 Water Heaters, Gas, Volume I, StorageType, 75,000BTUH Input or Less: ANSIZ.I0.1-1993 and
Supplements Z21.10.1a-
1994, Z21.l0.1b-1994,
Z21.l0.1c-1996.
8 Water Heaters, Gas, Volume III, Storage Type with Inputabove 75,000BTUH, ANSIZ21.l0.3-1993 and
Circulating and Instantaneous Water Heaters: Supplements Z21.10.3a-
1994, Z21.l0.3b-1994.
9 Water Heaters, Household Electric Storage Tank Type: ANSI/UL 174-1996.
10 Water Heaters, Instantaneous, Electric, Point-of-Use: ANSIlUL499-1987.
11 Water Heaters, Oil-Fired Storage Type: ANSI!UL 732-1987.
12 Water Heater Relief Valve Drain Tubes: ASMEA1l2.4.1-1993
(R2001).
13 Water Softeners (Cation Exchange): ANSI/NSF 44-1996.
14 Reverse Osmosis Drinking Water Treatment Systems: ANSI!NSF58-1997.
15 Macerating Toilet Systems and Related Components: ASME A112.3.4-2000;
CSA B45.9-2000.
VIII. VALVES AND APPURTENANCES
I BackwaterValves: ANSI A1l2.14.1-1975

(R 1998),
CSA B181.l-96 (ABS),
CSA B181.2-96 (PVe).
2 Anti-siphon Fill Valves (Ballcocks) for Gravity Water Closet Flush Tanks: ANSI/ASSE 1002-1999.
..,
.) MSS SP-80-1997.
Bronze Gate, Globe, Angle andCheck Valves:
4 Check Valves,Swing,Cast-Iron: MSS SP-71-1997.
5 Cleanouts: ASMEAI12.36.2M-1991.
6 Drain Valves, WaterHeater: ASSE 1005-1999.
7 Flushometers (Pressurized Flushing Devices): ANSI!ASSE 1037-1990.
8 Gate Valves,Cast-Iron, 125#and250#: MSS SP-70-1990.
9 Gate Valves, Iron Body (3" and larger): ANSI!AWWA C500-93
and Supplement CSOOa-95.
10 Reducing and Regulating Valves: ANSI!ASSE 1003-1995.
11 Relief Valves and Automatic Gas Shut-off Devices for Hot Water Supply Systems: ANSI Z21.22-1986 and
Supplement Z21.22a-1990.
12 Temperature Actuated Mixing Valves for Hot Water Distributions Systems: ANSI!ASSE 1017-1998.
13 Trap Seal Primer Valves, DrainageType: ASSE 1018-1986.
14 Water Hammer Arrestors: ANSI!ASSE 1010-1998,
PDIWH201.
15 Pressure Pre-Pressurized Potable Water Tanks (for thermal expansion): IAPM 0 PS 88-95.
16 Multi-port Electronic (orelectric)Trap Primers: IAPMO PS 79-95.

IX. BACKELOW PREVENTION DEVICES
I Air Gap Drain for Domestic Dishwashers: ASSE 1021-1977.

2 Backflow Preventerswith Intem1ediateAtmospheric Vent: ANSI/ASSE 1012-1995.
3 Detector Assembly, Double Check Type: ANSI/ASSE 1048-1999.
4 Detector Assembly, Reduced Pressure Type: ANSI/ASSE 1047-1999.
5 Double Check Valve Assembly: ANSI/ASSE 1015-1999.
6 Dual Check Valve Type BackflowPreventer: ANSI/ASSE 1024-1998.
7 Dual Check Valve for Carbonated Beverage Dispensers: ANSI/ASSE 1032-1980.
8 Reduced Pressure PrincipleBackflowPreventer: ANSI/ASSE 1013-1999.
9 VacuumBreaker,Atmospheric(Pipe-Applied): ASSE 1001-1998.
10 Vacuum Breaker, Hose Connection: ANSI/ASSE 1011-1995.
II Vacuum Breaker,LaboratoryFaucet: ANSI/ASSE 1035-1995.
12 Vacuum Breaker, Pressure (recommendedfor outdoor use): ASSE 1020-1998.
13 Backflow Prevention Requirements for Fixture Fittings with Hose Connected Single CSA B125-93;
Movable Outlets: IAPMO PS-49-92.
14 Hose Connection Backflow Preventers: ANSI/ASSE 1052-1994.
15 Vacuum Breakers, Pressure (Indoor)Back SiphonageBackflow: ANSI/ASSE 1056-1995.
16 Air Gaps in Plumbing Systems: ANSI/ASMEA112.1.2-
1991 (RI998).
17 Perfom1anceRequirements for Backflow Protection Devices and Systems in
PlumbingFixtureFittings: ASMEA112.18.3-96.
18 Air Gap Fittings for Use with Plumbing Fixtures, Appliances and Appurtenances: ASME A112.1.3-2000.
19 Outdoor Enclosures for BackflowPrevention Assemblies: ASSE 1060-1996.
X. MISCELLANEOUS
1 Copper Flashing (sheet): ASTMB370-98.

2 Lead Flashing (sheet): ASTMB749-97.
'"
.) Pipe Hangers and Supports (materials, design, manufacture): MSS SP-58-1993.
4 Poly (Vinyl Chloride) (PVe) Plastic Flexible Concealed Water-Contaminant Membrane: ASTM D4551-96.
5 Shower Pan Liner (PVC Plastic Sheeting): ASTM D4551-96.
6 Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane: ASTM D4068-96.
7 Shower Pan Liner (Plastic Sheeting): ASTM D4068-96.
8 Grease Interceptors: PDI-GI01-96.
9 Floor Affixed Supports for Off-the-Floor Plumbing Fixtures for Public Use: ASMEA112.6.1-1997.
10 Framing Affixed Supports forOff-the-Floor Plumbing Fixtures: ASME AI12.6.2-2000.

XiI. RziQM;Mil\iD,QiJQ;I,;Ilj;ii'IP'iI;9I,J;'LJJ1IQiJQ,
INST ALLATION,ANDTESTING
1 Installation of Ductile-Iron Water Mains and Appurtenances: ANSI!AWWA C600-93.

2 InstallingVitrifiedClayPipeLines: ASTM CI2-95.
3 Safe Handling of Solvent Cements, Primers and Cleaners Used for Joining
Thermoplastic Pipe and Fittings: ASTM F402-93.
4 Practice forMaking Solvent-CementedJoints withPoly(Vinyl Chloride)(PVe) Pipe
and Fitting: ASTM D2855-96.
5 Underground Installation of Thermoplastic Pressure Pipe (up to 6"): ASTM D2774-94.
6 Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity Flow
Applications: ASTM D2321-1995.
7 Recommended Practice for Installation of Thermoplastic Pipe and Corrugated
Tubing in Septic Tank Leach Fields: ASTM F481-97.
8 Plastic Fitting Patterns; Drain, Waste, and Vent (DWV): ASTM D3311-94.
9 Selection and Application of Pipe Hangers and Supports: MSS SP-69-1996.
10 Fabrication and Installation Standards for Pipe Hangers and Supports: MSS SP-89-1998.
11 Field Test Procedures for Backflow Prevention Devices: ASSE 5010-1998.
12 Professional Qualification Standardfor Backflow Prevention Assembly Testers, ANSI!ASSE 5000 Series-
Repairers, and Surveyors: 1991.
13 Practice for Heat-Joining Polyolefin Pipe and Fittings: ASTM D2657-97.
14 Practice for Electrofusion Joining Polylefin Pipe and Fittings: ASTMFI290-93.
15 Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings: ASTM B828-00.
16 Standard for Health Care Facilities: NFPA 99-2002.
17 Gas and Vacuum Systems: NFPA 99C-2002.
18 Professional Qualification Standards for Medical Gas Systems Installers, Inspectors,
Verifiers, Maintenance Personnel, and Instructors: ASSE Series 6000-2001.
1 See application sections of Chapter 3 for limitations on specific piping materials.

2 Pipe sizes contained in parentheses ( ) are provided for general information on the scope of the
referenced standard and are not intended to limit use.
3 Alloy shall be marked in pipe and fittings.

TABLE 3.4-MATERIALS FOR HOT WATER DISTRIBUTION
POTABLE WATER COLD WATER DISTRIBUTION
(I) (2) (3) (4) (5) WATER SERVICE PIPING
A8S Plastic Pipe, SDR (ASTM D2282) .

A8S Plastic Pipes, Schedule 40 or 80 (ASTM D 1527) .
8rass Pipe (ASTM843) . . .
Copper Pipe (ASTM 842) . . .
CopperWaterTube, Type K or L (ASTM888) . . .
Copper Water Tube, Type M (ASTM 888) . . .
Cpye Plastic Pipe, Schedule40,80 (ASTMF441) . . .
CPYC Plastic Pipe, SDR (ASTM F442) . . .
CPYC Plastic Water Distribution Systems (ASTM D2846) . . .
Ductile Iron Pipe, Cement-lined
(ASTM A377, ANSI/AWWA C1511A21.51) . )t, q
Fiberglass Pressure Pipe (AWWA C950) .
Galvanized Steel Pipe (ASTM A53) . . .
PE High-DensityPolyethylene(HDPE) Plastic Pipe, SDR-lJ
(ASTM F714) . ii
PE Plastic Pipe, Schedule 40 (ASTM 02104) .

PE Plastic Pipe, Schedule 40,80 (ASTM D2447) .
PE Plastic Pipe, SDR (ASTM 03035) . WW) q,;!!!
PE Plastic Pipe, SIDR (ASTM D2239) .

PE Plastic Tube (ASTM 02737) .
PE Plastic Pressure Pipe and Tubing (AWWA C90 I) .
PE-AL-PE Composite Pressure Pipe
'"
(ASTM F1282, CAN/CSA (8137.9) . .
PEX-AL-PEX Composite Pressure Pipe
(ASTM F1281, CAN/CSA (8137.10) . . .
PEX Plastic Water Distribution Systems (ASTM F877 with
ASTM F1807, FI960 Fittings or F2098 Fittings) . . .
CrosslinkedPolyethylene(PEX) TubingASTM F876 (ASTM
F877 with ASTM F 1807, F 1960 Fittings or F2098 Fittings) . . .
PYC Plastic PressurePipe, (AWWA C900) .
PYC Plastic Pipe, Schedule 40,80,120 (ASTM D1785) .
PYC Plastic Pipe, SDR (ASTM D2241) .
~
Approved Not Approved
(I) Piping for potable water shall be water pressure rated for not less than 160 psig at 73F.
(2) Piping for hot water shall be applied within the limits of its listed standard and the manufacturer's
recommendations.
(3) Plastic piping materials shall comply with NSF 14.
(4) Minimum SDR-Il for trenchless water service replacement systems.
(5) Permitted for trenchless replacement replacement of underground portions of piping within buildings.

TABLE 3.5 - MATERIALS FOR ABOVEGROUND WITHIN BUILDINGS
SANITARY WASTE & DRAIN UNDERGROUND WITHIN BUILDINGS
(I) (2) (3) (4) (5) (6) (7) SEWERS OUTSIDE OF BUILDINGS
ABS PIPEA'IDFITTI'IGS,SCHEDULE
40 DWV (ASTM D2661) . . .
ABS Pipe- Cellular Core(ASTM F628) and DWV Fittings . . .
ABS Sewer Pipe and Fittings (ASTM D2751) (2) .
ABS and PVCComposite SewerPipe(ASTM D2680) .
Brass Pipe (ASTM B43) .
Cast-Iron Soil Pipe and Fittings
- Bell and Spigot (ASTM A 74) . . .
Cast-Iron Soil Pipe and Fittings
- Hubless(CISPI301, ASTM A888) . . .
CellularCore PVCSewerand DrainPipe(ASTM F891)(3) .
CellularCore PVCSewerand DrainPipe(ASTM F891)(4) .
Cellular Core PVC DWVPipe, IPS Schedule40 (ASTM F891) . . .
Concrete Drain Pipe. Nonreinforced (ASTM C 14) .
Concrete Drain Pipe, Reinforced (ASTM C76) .
Copper Pipe (ASTM B42) . . .
Copper Tube - DWV (ASTMB306)
and Copper Drainage Fittings(ANSI B 16.23) . . .
Copper WaterTube - K,L,M(B88)
and Copper Drainage Fittings (ANSI B I6.23) . . .
Fiberglass Sewer and Pressure Pipe (ASTM D3 754)
and Fiberglass Non-Pressure Pipe Fittings (ASTM D3840) .
GalvanizedSteelPipe(A53)
and Cast-Iron Drainage Fittings(ASME B 16.12) .
PE High-Density Polyethylene (HDPE) Plastic Pipe,
SDR-17,(ASTM F714)(4)(6) .
PVC Pipe and Fittings, DWV(ASTM D2665) . . .
PVCSchedule40 Drainageand DWVFarbricatedFittings
(ASTMFI866) . . .
PVC Sewer Pipe(PS-46) and Fittings(ASTMF789) .
PVC SewerPipe (PSM)and Fittings(ASTMD3034)(2) .
Stainless Steel DWV Systems- Type 3 I6L
(ANSIIASMEA112.3.1)(5) . . .
StainlessSteelDWVSystems- Type
(ANSI/ASMEAl12.3.I)(5)
304
.
VitrifiedClay Pipe- StandardStrength(ASTMC700) .
VitrifiedClay Pipe- ExtraStrength(ASTMC700) . .
Lead Pipeand Fittings(FS WW-P-325B) .
I .
Approved
I I I
Not Approved
(I) Plastic drain, waste, and vent piping classified by standard dimensionn ratio shall be SDR 26 or
heavier (lower SDR number).
(2) Plastic sewer pipe classified by pipe stiffness shall be PS-46 or stiffer (higher PS number)..
(3) Piping shall be applied within the limits of its listed standard and the manufacturer's
recommendations.
(4) PS-1 00 pipe or stiffer (higher PS number).
(5) Alloy shall be marked on pipe and fittings
(6) Minimum SDR-I 7 fortrenchless sewer replacement systems.
(7) Permitted for trench less replacement systems.
102 2003 National Standard PUn/hing Code-Illustrated
TABLE3.6.MATERIALSFOR ABOVEGROUND
VENT PIPING UNDERGROUND
(I) (2)
ABS Pipe and Fittings, Schedule 40 DWV (ASTM D2661) . .
ABS Pipe - Cellular Core (ASTM F628) and DWV Fittings . .
Brass Pipe (ASTMB43) .
Cast-IronSoil Pipe and Fittings
-Bell and Spigot (ASTM A74) . .
-Hubless (CISPI 301, ASTM A888) . .
Cellular Core PVC DWV Pipe, IPS Schedule 40 (ASTM F891) . .
Copper Pipe (ASTM B42) .
Copper Tube - DWV (ASTM B306)
and Copper Drainage Fittings (ANSI B 16.23) . .
CopperTube - K, L, M (B88)
and Copper Drainage Fittings (ANSI B 16.23) . .
GalvanizedSteel Pipe (A53)
and Cast-IronDrainageFittings(ASMEB]6.12) .
PVC Pipe and Fittings, DWV (ASTM D2665) . .
PVC Schedule40 Drainageand DWVFabricatedFittings
(ASTM F]866) . .
StainlessSteel DWV Systems-Type3]6L
(ANSIIASME A 112.3.1)(2) . .
StainlessSteel DWV Systems-Type304
(ANSIIASME AI12.3.1)(2) .
3.25" OD PVC Pipe and Fittings, DWV (ASTM D2949) . .
VitrifiedClay Pipe - Extra Strength(ASTMC700) .
.
ApprovedNot Approved
(I) Piping shall be applied within the limits of its listed standards and the manufacturer's
recommendations.
(2) Alloy shall be marked on pipe and fittings.
200] National Standard Pumbing Code-Illustrated 103

TABLE 3.7 - MATERIALS FOR ABOVEGROUND WITHIN BUILDINGS
STORM DRAINAGE UNDERGROUND WITHIN BUILDING
(I) (2) (3) (4) (5) (6) (7) SEWERS OUTSIDE OF BUILDING
ABS Pipe and Fittings, Schedule 40 DWV (ASTM D2661) . . .

ABS Pipe - Cellular Core (ASTM F628) and DWV Fittings . . .
ABS Sewer Pipeand Fittings(ASTMD2751)(2) (3) .
ABS and PVC Composite Sewer Pipe (ASTM D2680) .
Brass Pipe (ASTM B43) .
- Bell and Spigot (ASTM A74) . . .
- Hubless (CISPI 301, ASTM A888) . . .
Cellular Core PVC Sewer and Drain Pipe (ASTM F891) (3) .
Cellular Core PVC Sewer and Drain Pipe (ASTM F891) (4) .
Cellular Core PVC DWV Pipe, IPS Schedule 40 (ASTM F891) . . .
Concrete Drain Pipe, Nonreinforced(ASTMC14) .
ConcreteDrain Pipe, Reinforced(ASTMC76) .
Copper Pipe (ASTM B42) .
Copper Tube - DWV (ASTM B306)
and Copper Drainage Fittings (ANSI BI6.23) . . .
CopperTube - K,L,M,(B88)
and Copper Drainage Fittings (ANSI BI6.23) . . .
GalvanizedSteel Pipe (A53)
and Cast-Iron Drainage Fittings (ASME B 16.12) .
PE- High-DensityPolyethylene(HDPE) Plastic Pipe,
SDR-I7, (ASTM F714)(6) .
PVC Pipe and Fittings, DWV (ASTM D2665) . . .
PVC Schedule40 Drainageand DWVFabricatedFitting
(ASTM F1866) . . .
PVC Sewer Pipe(PS-46)and Fittings(ASTMF789) .
PVC Sewer Pipe (PSM) and Fittings (ASTM 03034) (2) (3) .
StainlessSteel DWV Systems-Type316L (ANSI/ASMEAI12.3.1)(5) . .
Stainless Steel DWV Systems-Type 304 (ANSI/ASME A 112.3.1)(5) .
VitritiedClay Pipe - StandardStrength(ASTMC700) .
VitrifiedClay Pipe - Extra Strength(ASTMC700) . .
.
ApprovedNot Approved
(1) Piping shall be applied within the limits of its listed standards and the manufacturer's
recommendations.
(2) SDR 35 pipe or heavier (lower SDR number).
(3) PS-46 pipe or stiffer (higher PS number).
(4) PS-l 00 pipe or stiffer (higher PS Number).
(5) Alloy shall be marked on pipe and fittings
(6) Minimum SDR-17 for trench less sewer systems.
(7) Permitted for trenchless replacement systems.
104 200] National Standard PlIInbing Code-Illustrated
TABLE 3.8 - MATERIALS FOR
FOUND AnON DRAINS AND SUB-SOIL DRAINAGE
Clay Drain Tile (ASTM C498)

Concrete Drain Tile (ASTM C412)
Perforated Concrete Pipe (ASTM C444)
Corrugated Polyethylene Tube (ASTM F405)
SR Plastic Drain Pipe and Fittings, Perforated (ASTM 02852)
PVC Sewer Pipe and Fittings, Perforated (ASTM 02729)
StainlessSteelDWVSystems- Type 316L (ANSI/ASME AI12.3.1)
Vitrified Clay Pipe, Perforated, Standard and Extra Strength (ASTM C700)

Blank Page

Chapter 4
Joints and Connections
4.1 GENERAL REQUIREMENTS

4.1.1 Tightness
Joints and connections in the plumbing system shall be gas tight and watertight for the pressure required by
test, with the exceptions ofthose portions of perforated or open joint piping which are installed for the purpose
of collecting and conveying ground or seepage water to the underground storm drains.
Comment: Perforated and open-joint piping is also usedfor the piping in absorption trenches for private
sewage disposal systems. See Section 16.9.5.
4.1.2 JointStandards
a. Pipe and tube shall be cut 90 or perpendicular to the pipe center lines.
b. The inside diameter of pipe and tube ends shall be reamed, filed, or smoothed to size of bore and all
chips removed. All burrs on the outside ofthe pipe and butt ends shall be removed before the installation.
c. Pipe and tube shall engage into fittings the full manufacturer's design depth of the fitting socket.
d. Male pipe threads shall be made of sufficient length to ensure the proper engagement.
e. Pipe shall not extend into a fitting or other pipe to such a depth that it will impede or restrict the design
flow.
f. Joints made by bonding, welding, brazing, solvent cementing, soldering, burning or fusion shall be free
from grease or other substances not specifically required to achieve a satisfactory joint.
g. Pipe sealing or lubricating compound required for threaded pipe joints shall be applied to the male pipe
end only and shall be insoluable and nontoxic.
Comment: For industry standardsfor the variousjoining methods, refer to Table 3.1.3 - Part IV Pipe
Joints, Joining Materials, Couplings, Gaskets.
4.1.3 ExpansionJoints
Mechanical type expansionjoints requiring or permitting adjustment shall be accessible for adjustment and/or
replacement.
4.1.4 Increasers and Reducers

Where different sizes of pipes or pipes and fittings are to be connected, increaser and reducer fittings or
bushings shall be used. (See Section 2.4.3)

4.2 TYPES OF JOINTS FOR PIPING MATERIALS
4.2.1 Caulked
4.2.1.1 Cast-Iron Soil Pipe
Leadcaulkedjoints forcast-ironhubandspigotsoilpipe shallbe finnly packedwithoakumorhemp andfilled
with molten lead not less than 1 inch deep and not to extend more than 1/8 inch below the rim of the hub.
No paint, varnish, or other coatings shall be pennitted on thejointing material until after thejoint has been
tested and approved. Lead shall be run in one pouring and shall be caulked tight. See Figure 4.2.1.1
LEAD - ONE CONTINUOUS POUR

SET WITH CAULKING IRONS
CAST IRON CAST IRON

HUB END SPIGOT END
Figure 4.2.1.1
A LEAD CAULKED JOINT IN CAST IRON SOIL PIPE
4.2.1.2 Cast-Iron Water Pipe

Leadcaulkedjoints for cast-ironball and spigotwaterpipe shall be finnly packedwith clean dryjute, or treated
paper rope packing. The remaining space inthe hub shall be filled with molten lead accordingto the following
schedule:
Pipe Size Depth of Lead
Up to 20 inches 2-1/4 inches
24,30,36 inches 2-1/2 inches
Larger than 36 inches 3 inches
Lead shall be run in one pouring and shall be caulked tight. See Figure 4.2.1.2
LEAD - ONE CONTINUOUS POUR
APPROVED SEALING MATERIAL SET WITH CAULKING IRONS
CAST IRON CAST IRON

WATER PIPE WATER PIPE
HUB END SPIGOT END
Figure 4.2.1.2
A LEAD CAULKED JOINT IN IRON WATER PIPE

4.2.2 Threaded
Threadedjoints shallconformto approvedstandardsas listedin Table3.1.3. See Figure4.2.2
REAMED CHAMFER
MALE
THREADS
Figure 4.2.2
A THREADED PIPE JOINT
4.2.3 Wiped
Joints in lead pipe or fittings, or between lead pipe or fittings and brass or copper pipe, ferrules, solder nipples,
or traps, shall be full wiped joints. Wiped joints shall have an exposed surface on each side of a joint not less
than 3/4 inch and at least as thick as the material being jointed. Wall or floor flange lead-wipedjoints shall be
made by using a lead ring or flange placed behind the joints at wall or floor. Joints between lead pipe and
cast-iron, steel, or wrought iron shall be made by means of a caulking ferrule, soldering nipple, or bushing.
See Figure 4.2.3
/ COPPER PIPE
Figure 4.2.3
A WIPED JOINT ON LEAD PIPE
4.2.4 Soldered
Soldered joints for the tube shall be made with approved fittings. Surfaces to be soldered shall be cleaned
bright. The joints shall be properly fluxed and made with approved solder. Joints in copper water tube shall be
made by the appropriate use of approved cast brass or wrought copper fittings. Joints for potable water used
in copper, brass wrought copper fittings shall be made with a solder containing not more than 0.2 percent
lead. See Figure 4.2.4

Comment: The limit on lead in solderfiller metal is to reduce the level of lead in drinking water in
accordancewiththeEPA Safe Drinking WaterAct.
/ COUPLING
/ / SOLDER FILLER METAL
<
COPPERTUBE COPPERTUBE
() ))
Figure 4.2.4
A SOLDERED JOINT
4.2.5 Flared
Flared joints for copper water tube shall be made with fittings complying with ASME B 16.26listed in Table
3.1.3.The tube shallbe reamedandthen expandedwith an approvedflaringtool. SeeFigure 4.2.5
rWRENCH FLAT
FLARENUT;
ANNEALEDCOPPERTUBINj:
NOTES:
1. A long flare nut is shown. Short flare nuts are permissible where vibration is not a factor.
Figure 4.2.5
A FLARED COPPER JOINT
4.2.6 Press Joints

Press-type mechanical joints in copper water tube shall be made in accordance with manufacturer's instruc-
tions using approved tools which affix the copper fitting with integral o-ring to the tubing

4.2.7 Reserved
4.2.8 Brazed Joints
4.2.8.1 Brazed Joints
Brazed joints shall be made by first cleaning the surfaces to be joined down to the base metal, applying flux
approved for suchjoints and for the filler metal to be used, and making thejoint by heating to a temperature
sufficient to melt the approved brazing filler metal on contact.
4.2.8.2 Mechanically Formed Tee Fittings

Mechanically formed tee fittings may be made in copper tube. They shall be made with an appropriate tool and
joined by brazing. To prevent the branch tube from being inserted beyond the depth ofthe mechanically formed
tee fitting, depth stops shall be provided V4"above the dimple that acts as a depth stop, a second dimple shall
be placed to act as a point of inspection. Dimples shall be in line with the run ofthe tube. The brazed joints shall
be made according to Section 4.2.8.1and ASTM F20 141isted in Table 3.1.3. Such assemblies shall not be used
for drainage applications.
4.2.9 Cement Mortar

a. Where permitted as outlined in Sec. 2.4.4, cement mortar joints shall be made in the following manner:
1. A layer of jute or hemp shall be inserted into the annular joint space and packed tightly to prevent
mortar from entering the interior of the pipe or fitting.
2. Not more than 25 percent of the annular space shall be used for jute or hemp.
3. The remaining space shall be filled in one continuous operation with a thoroughly mixed mortar com-
posed of one part cement and two parts sand, with only sufficient water to make the mixture workable by
hand.
4. Additional mortar of the same composition shall then be applied to form a one to one slope with the
barrel of the pipe.
5. The bell or hub of the pipe shall be left exposed for inspection.
6. When necessary the interior of the pipe shall be swabbed to remove any mortar or other material which
may have found its way into such pipe.
Comment: Cement mortar joints have been virtually eliminated by the use of alternatejoining methods
and materials.
4.2.10 Burned Lead (Welded)

Burned (welded) joints shall be made in such a manner that the two or more sections to be joined shall be
uniformly fused together into one continuous piece. The thickness ofthe weld shall be at least as thick as the
lead beingjoined.
Comment: The added welding material must be of the same composition as the lead pipe being joined.
4.2.11 Mechanical (Flexible or Slip Joint)

4.2.11.1 Stainless Steel DWV Systems
a. Joints in stainless steel DWV systems shall be made with an elastomeric o-ring of a material which is
suitable for the intended service.
b. Joints between stainless steel drainage systems and otherpiping materials shall be made with an approved
adapter coupling.
2003 National Standard Pumbing Code-JI/ustrated 111

4.2.11.2Cast-Iron Soil Pipe
a. Hubless pipe: Joints for hubless cast-iron soil pipe and fittings shall be made with an approved elastomeric
sealing sleeve and corrosion resisting clamping device or shall be made using a rigid unshielded TPE coupling
with center stop installed per Section 4.3.8d.
b. Hub and Spigot: Joints for hub and spigot cast-iron soil pipe and fittings, designed for use with a compressed
gasket, may be made using a compatible compression gasket which is compressed when the spigot is inserted
into the hub of the pipe.
See Figures 4.2.11.2-A and -B
SHIELD
ELASTOMERIC
/ CORROSION RESISTANT CLAMP AND SCREWS
GASKET ~I / /
HUBLESS HUBLESS
CAST IRON CAST IRON
"'- SHIELDED COUPLING
Figure 4.2.11.2-A
A SHIELDED COUPLING ON HUBLESS CAST IRON SOIL PIPE
COMPRESSION GASKET
CAST IRON CAST IRON

HUB END SPIGOT END
Figure 4.2.11.2-B
A CAST IRON HUBBED JOINT WITH A COMPRESSION GASKET

4.2.11.3 Cast-Iron Water Pipe
Mechanical joints in cast-iron water pipe shall be made with a flanged collar, a rubber ring gasket, and the
approved number of securing bolts. See Figure 4.2.11.3
GASKET TEE HEAD BOLT
GLAND
"" ",",
Figure 4.2.11.3
A MECHANICAL JOINT ON IRON WATER PIPE
4.2.11.4 Clay Pipe

Joints in piping and/or fittings shall be made using flexible compressionjoints. See Figure 4.2.11.4
CORROSION RESISTANT
CLAMPS AND SCREWS
RUBBER COUPLING ~
-- --
CLAY PIPE- CLAY PIPE-
PLAIN END PLAIN END
Figure 4.2.11.4
AN UNSHIELDEDCOUPLING ON PLAIN END CLAY PIPE

4.2.11.5 Concrete pipe
Flexible joints between lengths of concrete pipe may be made using approved compression type joints or
elastomeric materials born on the spigot end and in the bell (or hub) end of the pipe. See Figure 4.2.11.5
CONCRETEPIPE CONCRETEPIPE
BELL END SPIGOTEND
Figure 4.2.11.5
A JOINT IN BELL AND SPIGOT CONCRETE PIPE
4.2.11.6 Elastomeric Sleeves

Mechanical joints on drainage pipes below ground shall be made with an elastomeric seal conforming to AS TM
D3212, eSA B602 or ASTM e1173. Joints shall be installed in accordance with the manufacturer's
instructions.
4.2.12 Reserved
4.2.13 Reserved
4.2.14 Plastic
Joints in plastic piping shall be made with approved fittings by either solvent cemented or heat joined connec-
tions; approved couplings consisting of elastomeric sleeves and corrosion resisting metal screw clamps;
approved insert fittings; approved mechanical fittings; or threaded joints according to approved standards.
epve and pve solvent cemented joints shall use an approved primer appropriate for the material used. An
approved purple colored primer and solvent cement not purple in color shall be used in joining pve pipe and
fittings. An approved color primer not orange in color and solvent cement orange in color shall be used in
joining epve pipe and fittings. See Figures 4.2.14-A through-F
114 2003 National Standard Pumbing Code-I/Iustrated

PRIMER(IF REQUIRED)AND SOLVENT
CEMENTAPPLIEDTO PIPE ENDS
AND FITTINGSOCKET
WIPED BEAD ~
Figure 4.2.14-A
A SOLVENT CEMENT JOINT IN PLASTIC DWV OR WATER PIPING
ELASTOMERIC GASKET JOINT FOR UNDERGROUND

BUILDING DRAINS OR SEWERS
Figure 4.2.14-B
AN ELASTOMERIC GASKET JOINT FOR UNDERGROUND PLASTIC DWV PIPING
SHIELD
ELASTOMERIC
GASKET ~ ,
/ CORROSION RESISTANT CLAMPING SCREWS
PLASTIC DWV PIPE ~I ,I . /

"1 PLASTIC DWV PIPE
CORROSION RESISTANT CLAMPS
Figure 4.2.14-C
A SHIELDED COUPLING ON PLASTIC DWV PIPING
2003 National Standard Pumbing Code-ll/ustrated 115

PRIMER(IF REQUIRED)AND SOLVENTCEMENT
ON PIPE END AND INSIDEOF SOCKET
PLASTIC PIPE WITH SOCKET (BELL) END ~ / WIPED BEAD
Figure 4.2.14-D
A SOLVENT CEMENT JOINT IN SOCKET (BELL) END PLASTIC PRESSURE PIPE
CORROSION RESISTING CLAMP DEVICE

OR CRIMP RING ASSEMBLY
PLASTIC TUBING
1==
I
I
I--
I
L==
INSERT FITTING
NOTES
1. Some manufacturers recommendtwo clamps on each side of the fitting for additionaljoint strength.
Figure 4.2.14-E
AN INSERT FITTING JOINT IN PLASTIC TUBING

HEAT FUSED AREAS
Figure 4.2.14-F
A HEAT FUSED JOINT IN PLASTIC WATER PIPING
4.2.15 Slip
Slipjoints shall be made using approved packing or gasket material, or approved groundjoint brass compres-
sion rings. Groundjoint brass connections which allow adjustment of tubing but provide a rigidjoint when
made up, shall not be considered as slip joints. See Figure 4.2.15-A and-B
COMPRESSION SLIP NUT
METAL OR PLASTIC TUBING
NOTES:
1. Straight tubular joints having washers are slipjoints and require access. Refer to the definition of
"accessible"
Figure 4.2.15-A
A SLIP JOINT IN DRAIN TUBING

BRASS COMPRESSION RING
OR FERRULE
LOCKNUT
METAL OR PLASTIC TUBING
NOTES:
1. When a compression joint does not permit free movement when assembled, it is not considered to
be a slip joint and does not need to be accessible. Refer to the definition of "accessible".
Figure 4.2.15-B
A COMPRESSION JOINT IN DRAIN TUBING
4.2.16 Expansion
Expansionjoints shall be of approved type and its material shall conform with the type of piping in which it is
installed. See Figures 4.2.16-A,-B, and-C
Comment: Expansionjoints must to be accessiblefor adjustment or replacement. Refer to the definition

of" accessible".
O-RINGS
Figure 4.2.16-A
AN EXPANSION JOINT FOR PLASTIC DWV PIPING

-----------
m - ~ ~ ------------------
II
,-
I
I
I
----------------
------------------------
Figure 4.2.16-B
A MECHANICAL EXPANSION JOINT IN PRESSURE PIPING
ADJUSTABLE EXPANSION SLEEVE

WRENCH GRIP
WING NUT AND BOLT

(3 AT 1200 APART)
PACKING GLAND
PACKING
BODY
OUTLET
Figure 4.2.16-C
AN EXPANSION JOINT FOR ROOF DRAINS
4.2.17 Split Couplings

a. Split couplings consisting oftwo or more parts and a compression gasket, designed for use with grooved
or plain end pipe and fittings, shall be permitted to be used for water service piping, hot and cold domestic
water piping, storm water conductors and leaders, and sump pump discharge piping. The completejoint
assembly shall be suitable for the intended use and comply with a standard listed in Table 3.1.3.
b. Galvanized steel pipe or other interior coated pipe shall not be joined using rolled grooves.
See Figure 4.2.17

GASKET
GROOVED PIPE
'<',', '\,", """"<"""'<""
~"',,', '~
Figure 4.2.17
A GROOVED PIPE JOINT
4.2.18 Butt Fusion

ASTM F714 high-density polyethylene (HOPE) pipe and ASTM 03261 fittings shall be joined by butt fusion
in accordance with ASTM 02657.
4.2.19 Bending
Plumbing systems shall be installed in a manner conforming to this Code and industry installation standards.
Changes in direction of copper water tube shall be permitted to be made by the use of factory or field bends.
Bends shall be made only with bending equipment and procedures intended for that purpose. All bends shall
be smooth and free from buckling, cracks, and other evidence of mechanical damage. Pipe shall not be bent
through an arc of more than 90 degrees.
4.3 TYPES OF JOINTS BETWEEN DIFFERENT PIPING MATERIALS
4.3.1 Vitrified Clay to Other Material

Jointsbetweenvitrifiedclayandotherpipingmaterialsshallbe madewithan approvedjoint. See Figures
4.3.1-A and-B

COMPRESSION
JOINT SEALER
CLAY CAST IRON

PIPE PIPE
NOTES:
1. The rubber rings must be sized to adapt to the different outside diameters (0.0.) of the different
piping materials being joined.
2. There are hundreds of different adapters available for joining different materials, different pipe sizes,
and different wall thickness, as well as clay pipe from different manufacturers.
Figure 4.3.1-A
A RUBBER RING TRANSITION JOINT TO VITRIFIED CLAY PIPE
CENTER STOP
OTHER
CLAY
PIPING
PIPE
MATERIAL
~ \CORROSION RESISTANT CLAMPS
NOTES:
1. Externally clamped couplings (shielded and unshielded) are a common way of making transition
connections from vitrified clay pipe to other piping materials. Various sized gaskets are available to
adapt to the different outside diameters (0.0.) of the piping materials being joined.
Figure 4.3.1.B
AN EXTERNALLY CLAMPED TRANSITION COUPLING JOINT
TO VITRIFIED CLAY PIPE
4.3.2 Reserved
4.3.3 Reserved

4.3.4 ThreadedPipetoCast-Iron
Joints between steel or brass and cast-iron pipe shall be either caulked or threaded or shall be made with
approved adapter fittings. See Figure 4.3.4
THREADED STEEL OR BRASS PIPE
Figure 4.3.4
A THREADED PIPE TO CAST IRON ADAPTER FITTING
4.3.5 Lead to Cast-Iron or Steel

Joints between lead and cast-iron or steel pipe shall be made by means of wiped joints to a caulking ferrule,
soldering nipple, bushing, or by means of a mechanical adapter. See Figure 4.3.5
LEAD PIPE
-- BRASS CAULKING FERRULE
Figure 4.3.5
A WIPED LEAD TRANSITION JOINT

4.3.6 Cast-Ironto CopperTube
Joints between cast-iron and copper tube shall be made by using an approved brass or copper caulking ferrule
and by properly soldering the copper tube to the ferrule. See Figure 4.3.6
OAKUM LEAD
/
I ...,../ SOLDERED
CAST IRON COPPER

HUB END PIPE
, CAULKING FERRULE
Figure 4.3.6
A CAULKING FERRULE FOR CAST IRON TO SWEAT COPPER TRANSITION
4.3.7 Copper Tu be to Threaded Pipe Joints

a. Joints from copper tube to threaded pipe shall be made as follows:
1. DWV Systems: with copper or brass threaded adapters.
2. Potable Water Systems and Galvanized Steel Pipe: copper or brass threaded adapters that incorporate
electrical insulation.
3. To any Non-Ferrous Piping: copper or brass threaded adapter.
b. The adapter fitting shall be soldered to the tubing by approved methods, and the threaded section
assembled with National Pipe Threads-Tapered (NPT).
See Figures 4.3.7 - A and - B
COPPERTUBE r BRASS MALE ADAPTER

I r- THREADED FITTING
~.LDER ~~INT.
Figure 4.3.7-A
A SWEAT COPPER TO THREADED PIPE TRANSITION

COPPER SOLDER JOINT
CONNECTOR
INERT NSF I FDA

STEEL NUT LISTED LINING
(INSULATOR)
INSULATING
GASKET
- GROOVED,THREADED
OR PLAIN END
- WATERWAY FITTING
TAPERED PIPE THREADS
COPPER SOLDER JOINT

CONNECTOR
- ZINC ELECTROPLATED
STEEL CASING
DIELECTRIC
(INSULATOR)
FULLY SEPARATED
INSULATING DISSIMILLAR METALS
-
GASKET
COPPERADAPTER
TAPERED PIPE THREADS
Figure 4.3.7-B
DIELECTRIC UNION, FLANGE, AND WATERW AY FITTING
4.3.8 Special Joints and Couplings for Drainage Piping

a. Joints between two different drainage piping materials or between different size piping, of the same or
different material, shall be made using fittings or mechanical couplings that are designed for the specific
application, including adapter fittings, hubless pipe couplings, slip-on couplings, transition couplings, and repair
couplings.
b. Fittings and couplings for use under this Section shall either (1) comply with a standard listed in Table
3.1.3, (2) be listed or labeled by a recognized listing agency, or (3) be approved by the Authority Having
Jurisdiction if such products are not listed or labeled. Installation shall comply with the coupling
manufacturer's instructions and intended use.
c. Shielded couplings shall consist of a flexible elastomeric sealing sleeve, a protecting and supporting
continuous metal shield or shear ring, and metal screw clamping bands. All metal parts shall be corrosion-
resisting. Shielded couplings shall be capable of withstanding a shear test based on a load of 50 pounds per
inch of nominal pipe diameter, and shall be permitted to partially support the pipe beingjoined when such
installation is recommended by the manufacturer's instructions. Shielded couplings may be installed
aboveground or underground, as intended by the manufacturer.
d. Mechanical unshielded couplings using thermoplastic elastomer gaskets shall consist of a rigid or semi-
rigid sealing sleeve and corrosion-resisting metal screw clamping bands. Mechanical unshielded couplings
using thermoplastic elastomer gaskets shall not be installed where the operating internal or external tempera-
124 2003 National Standard Pumbing Code-fIIustrated

tures exceed 130F (54C) or are below OaF (-18C). The pipe shall be supported on both sides of the
coupling within 18 inches of the centerline ofthe coupling. Mechanical unshielded couplings using thermo-
plastic elastomer gaskets shall be permitted aboveground or underground. Mechanical unshielded couplings
using thermoplastic elastomer gaskets shall not be installed in construction that has a fire rating that restricts
the use of flammable materials or be installed in through penetrations or plenums without additional fire
resistance protection.
e. Flexible unshielded couplings shall consist of an elastomeric sealing sleeve and corrosive-resisting metal
screw clamping bands. The use of flexible unshielded couplings shall be limited to joints in underground sewer,
drain or vent piping.
f. Couplings installed aboveground shall include center stops.
EXCEPTION: Slip-on repair couplings used for repair or rework.
g. The shear tests required under this Section shall be performed in accordance with the shear test
procedures specified under any of the coupling standards listed in Table 3.1.3 that include such tests.
See Figures 4.3.8-A through-D
COUPLING SHIELD
FLEXIBLE ELASTOMERIC
SEALING SLEEVE
/// '////
~I //////////
CENTER STOP (WHERE REQUIRED)
~\ CORROSION RESISTANT CLAMPS
NOTES:
1. Shieldedcouplings can be used abovegroundand underground.They can partially support the pipe.
Center stops are required except for repair couplings.
Figure 4.3.8-A
A SHIELDED COUPLING ON DRAINAGE PIPING
RIGID OR SEMI-RIGID SEALING SLEEVE
FLEXIBLE ELASTOMERIC
SEALING SLEEVE ~~ 7
/////////////// // ,-777
CENTER STOP (WHERE REQUIRED)
=
=
= =
- -
~\ CORROSION RESISTANT CLAMPS
NOTES:
1. Rigid unshielded couplings can be used abovegroundand underground. They cannot support the
pipe. The pipe must be independently supported. Center stops are required except for repair
couplings.
Figure 4.3.8-B
A RIGID UNSHIELDED COUPLING ON DRAINAGE PIPING

FLEXIBLE ELASTOMERIC ADAPTOR
SEALING SLEEVE ~, ~ CORROSION RESISTANT CLAMPING SCREWS
"'I
~ DIRECTION OF
DRAINAGE FLOW
SHIELDED COUPLING j ~ CORROSION RESISTANT CLAMPS
Figure 4.3.8-C
A TRANSITION CONNECTION USING A SHIELDED COUPLING
r FLEXIBLE UNSHIELDED COUPLING
/
~ CORROSION RESISTANT
CLAMPING SCREWS
~ DIRECTION OF
DRAINAGE FLOW
CORROSION RESISTANT CLAMPS
NOTES:
1. Flexible unshielded couplings are limited to underground sewer, drain, and vent piping. Center
stops are required except for repair couplings. The couplings cannot support the pipe. The piping
must be properly backfilled to avoid stresses on the couplings.
Figure 4.3.8-D
A TRANSITION CONNECTION USING A FLEXIBLE UN SHIELDED COUPLING
4.3.9 ABS or pve Plastic DWV to Other Material

a. Threaded Joints: ABS or pve DWV joints when threaded shall use the proper male or female threaded
adapter. Use only approved thread tape or lubricant seal or other approved material as recommended by the
manufacturer.
Threadedjoints shall not be over-tightened. After hand tightening the joint, make a one-half to one full turn
with a strap wrench.

b. Cast-iron Hub Joints: Joints may be made by caulking with lead and oakum or by use of a compression
gasket that is compressed when the plastic pipe is inserted into the cast-iron hub end of the pipe. No adapters
are required for this connection.
c. Cast-iron Spigot Ends, Schedule 40 Steel Pipe or Copper DWV Tube: Joints between these materials
and plastic shall be joined with an approved adapter fitting.
See Figures 4.3.9-A through-D
MALE ADAPTOR - NPT X SOCKET

APPLIEDTO PIPE ENDAND INSIDEOF SOCKET
THREAD LUBRICANT
THREADED COUPLING
OR FITTING
Figure 4.3.9-A
A PLASTIC DWV THREADEDMALE ADAPTER
LEAD
OAKUM~-"
CAST IRON PLASTIC

PIPE PIPE
NOTES:
1. Plastic pipe that is lead caulked must be solid plastic. Molten lead will melt cellular core plastic
pipe.
Figure 4.3.9-B
A LEAD CAULKED JOINT FOR PLASTIC DWV TO CAST IRON HUB

COMPRESSION
~ GASKET 7
--- PLASTIC
PIPE
Figure 4.3.9-C
A COMPRESSION GASKETEDJOINT FOR PLASTIC DWV TO CAST IRON HUB

LASTIC PIPE APPLEDTO PIPE ENDAND INSIDEOF SOCKET
~ I
~ WIPED BEAD
~
/ /
LEAD
CAST IRONPIPE
PLASTIC ADAPTER FITTING
NOTES:
1. Plastic fittings that are lead caulked musty be solid plastic. Molten lead will melt cellular core pipe
fittings.
Figure 4.3.9-D
A LEAD CAULKED PLASTIC SOCKET JOINT TO CAST IRON PIPE

4.4 CONNECTIONS BETWEEN DRAINAGE PIPING AND CERTAIN
FIXTURES
a. Connections between drainage piping and floor outlet plumbing fixtures shall be made by means of an ap-
proved flange which is attached to the drainage piping in accordance with the provisions of this chapter. The floor
flange shall be set on and securely anchored to the building structure.
b. Connections between drainage piping and wall hung water closets shall be made by means of an approved
extension nipple or horn adapter.
c. Connections shall be bolted to the flange or carrier using corrosion resisting bolts or screws, or assemblies
recommended by the manufacturer.
See Figure 4.4
4.5 WATERPROOFING OF OPENINGS

Joints at the roof, around vent pipes, shall be made watertight by the use oflead, copper, aluminum, plastic, or
other approved flashing or flashing material. Exterior wall openings shall be made watertight.

Blank Page

.. . Cb~ptet5
Traps, Cleanouts and Backwater Valves

5.1 SEPARATE TRAPS FOR EACH FIXTURE
a. Plumbing fixtures shall be separately trapped by a water seal trap placed as close as possible to the fixture
outlet.
b. The vertical distance from the fixture outlet to the trap weir shall not exceed 24 inches.
c. Fixtures shall not be double-trapped unless a relief vent is provided between the two traps.
d. Fixture designs having integral dual traps within the fixture shall be permitted.
EXCEPTIONS:
(I) Fixtures that have integral traps.
(2) A combination-plumbing fixture may be installed on one trap provided the waste outlets are not more than
30 inches apart.
(3) One trap may be installed for up to three (3) compartment sinks, laundry trays or lavatories that are
immediately adjacent to each other in the same room, and where the trap is centrally located when three such
fixtures are installed.
(4) No clothes washer or laundry tub shall be discharged to a trap serving a kitchen sink.
(5) As otherwise permitted by this Code.
See Figures 5.1-A through-D
LAVATORY
~ MAXIMUMDISTANCEFROM
, , t FIXTURE OUTLET TO TRAP WEIR
24
INCHES
FIXTURE
TAILPIECE
NOTES:
1. Vertical distances greater than 24" may induce self-siphoning of the trap seal due to the momentum
ofthe drainageflow.
Figure 5.1 - A
THE VERTICAL DISTANCEFROM A FIXTURE OUTLET TO ITS TRAP WEIR
2003 National Standard ?umbing Code-Illustrated 131

WATER CLOSET
Figure 5.1 - B
A FIXTURE WITH AN INTEGRAL TRAP
SINK SINK
END OUTLET
l-- 30"
MAXIMUM
- J-
NOTES:
1. Refer to the definitions of "Continuous Waste" and "Combination Fixture".
Figure 5.1 - C
A CONTINUOUS WASTE WITH END OUTLET
SINK SINK
~ CENTER OUTLET
[ 1T~
j
RAP
30"
MAXIMUM
NOTES:
1. Refer to the definitions of "Continuous Waste" and "Combination Fixture".
Figure 5.1 - D
A CONTINUOUS WASTE WITH CENTER OUTLET

5.2 SIZE OF FIXTURE TRAPS
Fixture trap size (nominal diameter) shall be sufficient to drain the fixture rapidly and in no case less than given in
Table 5.2. No trap shall be larger than the drainage pipe into which it discharges. Integral traps shall conform to
appropriate standards.
Comment: A drain pipe that is smaller than the trap to which it is connected could create an obstruction
toflow through the trap.
5.3 GENERAL REQUIREMENTS FOR TRAPS
5.3.1 Design of Traps

Fixture traps shall be self-scouring and shall have no interior partitions except where such traps are integral
with the fixture or where corrosion resistant materials of plastic or glass are used. Solid connections, slip
joints, or couplings may be used on the trap inlet, trap outlet, or within the trap seal. (See Section 7.4.6.) See
Figures 5.3.1-A through-Co Refer to Sections 4.2.15 and 7.3.7 for slip joints and their required
access.
SOLID CONNECTIONS
FIXTURE TRAP
NOTES:
1. Access is not mandatory for traps with solid connections.
Figure 5.3.1 A -
A FIXTURE TRAP WITH SOLID CONNECTIONS
~ ESCUTCHEON
/ ~ WALL
NOTES: LOCKNUTS
1. Slip joints must be accessible
Figure 5.3.1 B-
A FIXTURE TRAP WITH SLIP JOINTS

~.--ti I ~ THREADED
\ CONNECTION
~ GROUND JOINT
SLIP JOINT
NOTES:
1. Only the slip joint must be accessible.
Figure 5.3.1 - C
A FIXTURE TRAP WITH THREE DIFFERENT TYPES OF JOINTS
5.3.2 Trap Seals

Each fixture trap shall have a liquid seal of not less than two inches and not more than four inches
EXCEPTIONS:
(I) Interceptors in Chapter 6.
(2) Special conditions such as accessible fixtures, a deeper seal may be required by the Authority Having
Jurisdiction.
See Figure 5.3.2
ROWNWEIROF TRAP
OUTLET
INLET
~c;~'/rl
TRAPSEAL
J.. FLOW-
DIP OF TRAP
NOTES:
1. The minimum trap seal depth of 2" is based on the design criteria for the vent piping. Trap seals
deeper than 4" will tend to trap solids and create a breeding ground for bacteria.
Figure 5.3.2
TRAP SEAL DEPTH

5.3.3 Trap Setting and Protection
Traps shall be set level with respect to their water seals and, where necessary, shall be protected from
freezing. See Figure 5.3.3
'I ~~g~~A~~EK ~~~~SAL UNIT
90 FLANGED TAILPIECE ON
FOOD WASTE DISPOSAL
NOTES
1. Tilted traps may self-siphonbecause ofthe reduction inthe effectivedepth ofthe trap seal.
2. Where freeze protectionis necessary, thermal insulationalone willnot prevent freezing, onlydelay
it. Traps should be located in heated spaces.
3. Where seasonal facilities are shutdown during the winter, fixture traps can be filled with an anti-
freeze solution that will not damage the traps or drain piping.
Figure 5.3.3
TRAPS MUST BE LEVEL AND PROTECTED FROM FREEZING
Table 5.2
MINIMUM SIZE OF NON-INTEGRAL TRAPS
Trap Size
Plumbing Fixture in inches
Bathtub (with or without overhead shower) 1112
Bidet 11/4
Clothes washing machine standpipe 2
Combination sink and wash (laundry) tray with food waste grinder unit 1112
(I)
Combination kitchen sink, domestic, dishwasher, and food waste grinder 1112
Dental unit or cuspidor 11/4
Dental lavatory 11/4
Drinking fountain 11/4
Dishwasher,commercial 2
Dishwasher, domestic (non-integral trap) 1112
Floor drain 2
Food waste grinder, commercial use 2
Food waste grinder, domestic use 1112
Kitchen sink, domestic, with food waste grinder unit 1112
Kitchen sink, domestic 1112
Lavatory,common 11/4
Lavatory (barber shop, beauty parlor or surgeon's) 1112
Lavatory, multiple type (wash fountain or wash sink) 1112
Laundry tray (lor 2 compartments) 1112
Shower stall or drain 2
Sink (surgeon's) 1112
Sink (flushing rim type, flush valve supplied) 3
Sink (service type with floor outlet trap standard) 3
Sink (service trap with P trap) 2
Sink, commercial (pot, scullery, or similartype) 2
Sink,commercial (withfoodgrinder unit) 2
(I) Separate trap required for wash tray and separate trap required for sink compartment with food waste grinder.

5.3.4 BuildingTraps
Building traps shall not be installed except where required by the Authority Having Jurisdiction. Eachbuilding
trap when installed shall be provided with a cleanout and with a relieving vent or fresh air intake on the inlet
side of the trap which shall be at least one-half the diameter ofthe drain to which it connects. Such relieving
vent or fresh air intake shall be carried above grade and terminate in a screened outlet located outside the
building.
Comment: Building traps are no longer installed in modern plumbing systems. They provide a collec-
tion point for solids and other waste that may cause line stoppages. Building traps also prevent the
building vent system from venting the building sewer. The Authority Having Jurisdiction may require
building traps if the sewer gas in the municipal sewage system is particularly corrosive or aggressive and
could damage the drain, waste, and vent piping in the building.
5.3.5 Prohibited Traps

a. The following types of traps shall be prohibited:
1. Traps which depend upon moving parts to maintain their seal.
2. Bell traps.
3. Crown vented traps.
4. Separate fixture traps which depend on interior partitions for their seal, except if made from plastic,
glass or other corrosion resistant materials.
5. "s" traps, of uniform internal dimension.
6. Drum traps.
b. Hair interceptors, precious metal interceptors and similar appurtenances shall be permitted as required.
See Figure 5.3.5
BALL TRAP WITH

1f
BELL TRAP
MOVING PARTS
&F~}
L
::J X mw" ""~,(X) IS
IF DISTANCE ~~oWITHIN
TWO PIPE DIAMETERS (Y)
~ PARTITION TRAP
(Note 1)
CROWN VENTED TRAP
"S" TRAP OF TUBULAR DESIGN

DRUM TRAP
NOTES:
1. Traps having internal partitions are permitted if constructed of plastic, glass, or other corrosion
resistant material.
Figure 5.3.5
PROHIBITED TRAPS

5.3.6 Trap Seal Maintenance
Traps which could lose their seal due to evaporation because of infrequent use shall be equipped with a
readily accessible means to replenish the trap seal or a trap primer conforming to ASSE 1018 or ASSE 1044
listed in Table 3.1.3. In addition to the priming requirement, the installation of a sealing component on the trap
inlet to reduce seal loss shall be permitted.
5.4 DRAINAGE PIPE CLEANOUTS
5.4.1 CleanoutSpacing
a. Cleanouts in horizontal drainage lines shall be spaced at intervals not exceeding the following values:
4" pipe size or less: 75 feet
5" size and larger: 100 feet
b. The distance referred to in Sections 5.4.1 a shall include the developed length of the cleanout pipe.
See Figure 5.4.1
co
"X" (See Notes)
NOTES
1. The maximum spacing "X" for pipes 4" and smaller is 75 feet, including the developed length to the
cleanoutopening.
2. The maximum spacing "X" for pipes 5" and larger is 100 feet, including the developed length to the
cleanoutopening.
3. Manholes may be used for cleanouts in building drains or building sewers (or branches thereof) that
are 8" size or larger. The maximum spacing is 300 feet. Refer to Section 5.4.10.
Figure 5.4.1
CLEANOUT SPACING ON HORIZONTAL DRAIN LINES
5.4.2 Building Sewer

Cleanouts, when installed on an underground building sewer, shall be extended vertically to or above the
finished grade level. See Figure 5.4.2
2003 National Standard PUl11bing Code-Illustrated 137

~
NOTES:
1. Cleanouts must haveflush top covers if located in a walkway or other paved area.
2. The length of the vertical extension to grade must be included in the developed length between
cleanouts.
Figure 5.4.2
A SEWER CLEANOUTEXTENDEDTO FINISHED GRADE
5.4.3 Change of Direction

Cleanouts shall be installed at each change of direction of the drainage system greater than 45.
EXCEPTION:Not morethan one cleanoutshallbe requiredin every40 feet of run. See Figure 5.4.3
FLOW ~
~
FLOW
NOTES:
1. A cleanout is not required at Points "B", "C", & "0" if the distance from Point "A" to Point "0" is
less than 40 feet.
Figure 5.4.3
WHERE CLEANOUTSARE REQUIRED AT CHANGES IN DIRECTION
5.4.4 Cleanouts for Concealed Piping

Cleanouts for concealed piping shall be extended through and terminate flush with the finished wall or floor;
or pits or chases may be left in the wall or floor, provided they are of sufficient size to permit removal of the
cleanout plug and proper cleaning of the system. See Figure 5.4.4
138 2003 National Standllrd Pumbing Code-Illustrated

~ WYE AND
~
/T
~
TEST PLUG
ARRANGEMENT
!- 11 CLEAN OUT
OR TEST TEE
TEE
RETAINING SCREW
"- ACCESS PLATE "'- CLEANOUT COVER
Figure 5.4.4
ACCESS TO CONCEALED CLEAN OUTS
5.4.5 Base of Stacks

a. A cleanout shall be provided near the base of each vertical waste or soil stack and located 6 inches
above the flood level rim ofthe lowest fixture on the lowest floor. Ifthere are no fixtures installed on the
lowest floor, the cleanout shall be installed at the base of the stack.
b. For buildings with a floor slab, a crawl space of less than 18 inches, or where a stack cleanout is not
accessible, the cleanout shall be installed in the building drain or building sewer, not more than five feet
outside the building wall.
c. Rain leaders and conductors connected to a building storm sewer shall have a cleanout installed at the
base of the outside leader or inside conductor before it connects to the horizontal drain.
See Figures 5.4.5-A,-B, and-C
SANITARY DRAIN OR STORMWATER STACK
SEALANT
/ r FLOOR LINE
~:.:}~h;:.hA!}4:.~l':;;:&ih.{!;n;f::~:~E~"~{~
Figure 5.4.5 - A
A CLEANOUT NEAR THE BASE OF A STACK
2003 National Standard Pumbing Code-lI/ustrated 139

INACCESSIBLE
SOIL OR WASTE i FOUNDATION WALL
STACK
t
NOT MORE
THAN 5 FEET --i r c8
CLEANOUT
BUILDING DRAIN
NOTES:
1. The extension of a cleanout for access in not considered to be a dead end.
Figure 5.4.5 - B
A CLEAN OUT EXTENDED TO OUTSIDE OF THE BUILDING FOR ACCESS
~
c ,~ ALTERNATE CLEAN OUT TEE
( eal
a~c~ ~
TO BUILDING
STORMSEWER
NOTES:
1. Cleanouts are required near the base of exterior rain leaders and interior conductors when they
connect to a building storm drain or building storm sewer.
Figure 5.4.5 - C
A CLEANOUT NEAR THE BASE OF A RAIN LEADER
5.4.6 Building Drain and Building Sewer Junction

a. There shall be a cleanout near the junction ofthe building drain and building sewer either inside or
outside the building wall.
b. A clean out shall be placed in the building sanitary sewer and building stonn sewer at the property line
and brought to the surface per the requirements of the Authority Having Jurisdiction.
See Figures 5.4.6 - A and - B

Figure 5.4.6 - A
A CLEANOUT AT THE JUNCTION OF THE BUILDING DRAIN AND BUILDING SEWER
NOTES:
1. The cleanout and cleanout connection to the sewer required by Section 5A.6.b must be withinthe
property.
Figure 5.4.6 - B
A CLEANOUTAT THE PROPERTY LINE
5.4.7 Direction of Flow

Cleanouts shall be installed so that the cleanout opens in the direction ofthe flow of the drainage line or at
right angles thereto. See Figure 5.4.7

TWIN TWO-WAY COMBINATION
CLEANOUT CLEANOUT WYE & 1I8TH BEND
NOTES:
1. Cleanouts must haveflush top covers if located in a walkway or other paved area.
Figure 5.4.7
THE FLOW DIRECTION OF CLEANOUTS
5.4.8 Connections to Cleanouts Prohibited

a. Cleanout plug openings in other than drainage pattern fittings shall not be used for the installation of new
fixtures or floor drains.
b. If a cleanout fitting or cleanout plug opening is removed from a drainage pattern fitting in order to
extend the drain, another cleanout of equal access and capacity shall be provided in the same location.
5.4.9 Cleanout Size

Cleanout size shall conform with Table 5.4.9.
Table 5.4.9
SIZEOFCLEANOUT
Nominal Nominal
Piping Size (inches) Size ofCleanout (inches)
11/4 11/4
11/2 11/2
2 2
3 3
4&6 4
8&10 6
12& 15 8
I Note: See Section 5.4.10 for sizes 12" or larger for building sewers.

5.4.10 Manholes for Large Pipes
a. Manholes shall be provided as cleanouts for building sewers 12" size and larger. Manholes shall be
provided at every change of size, alignment, direction, grade, or elevation. The distance between manholes
shall not exceed 300 feet.
b. Manholes may be provided in lieu of cleanouts in underground building sewers, building drains, and
branches thereof, 8" size and larger.
c. Such manholes shall comply with the requirements of Section 5.4.1 Oa.
d. If manholes are installed indoors, they shall have a bolted, gas-tight cover.
e. Manhole construction shall comply with the standards of the Authority Having Jurisdiction.
See Figure 5.4.10
300'
MAXIMUM
CHANGEOF
J M.H.
M.H.
DIRECTION CHANGE OF J 300'
MAXIMUM
DIRECTION
~
CHANGE OF
ELEVATION
J
Figure 5.4.10
LOCATION AND SPACING OF MANHOLES
5.4.11 Cleanout Clearances

Cleanouts on 3" or larger pipes shall be so installed that there is a clearance of not less than 18" for the
purpose of rodding. Cleanouts smaller than 3 inches shall be so installed that there is a 12" clearance for
rodding. See Figure 5.4.11-A and-B
2003 National Standard ?wnbing Code-Illustrated 143

NOTES:
1. Minimum clearance "X" is 12" if pipe size "0" = 2" or less
2. Minimum clearance "X" is 18" if pipe size "0" = 3" or more
Figure 5.4.11 - A
CLEANOUT CLEARANCE ABOVE THE BASE OF A STACK
't~:;(7'.:'; I.;::: ::.,~:~:;:.~.::.:.;::.

;~\ >;:~ ;,;:".;'::):.~:::::>'.:::-1
PIPE SIZE "D"~
~x
NOTES:
1. Minimum clearance "X" is 12" if pipe size "0" = 2" or less
2. Minimum clearance "X" is 18" if pipe size "0" = 3" or more
Figure 5.4.11 - B
CLEANOUT CLEARANCE AT THE BASE OF A STACK
5.4.12 Cleanouts to be Kept Uncovered

Cleanout plugs shall not be covered with cement, plaster, or any other permanent finishing material. Where it
is necessary to conceal a cleanout plug, a covering plate or access door shall be provided which will permit
ready access to the plug.
5.4.13 CleanoutEquivalent
Where the piping is concealed, a fixture trap or a fixture with integral trap, readily removable without disturb-

ing concealed roughing work, shall be accepted as a cleanout equivalent, provided the opening to be used as a
cleanout opening is the size required by Table 5.4.9.
EXCEPTION: The trap ann of a floor drain with a removable strainer.
See Figure 5.4.13-A and-B
Figure 5.4.13 - A
A WATER CLOSET AS A CLEAN OUT EQUIVALENT
SLIP JOINT J
~ GROUND OR
SLIP JOINT
Figure 5.4.13 - B
A REMOVABLE TRAP AS A CLEAN OUT EQUIVALENT

5.4.14 Cleanouts for Floor Drains
A cleanout shall be provided immediately downstream from a floor drain whose strainer is not readily remov-
able.
5.5 BACKWATER VALVES
5.5.1 Where Required

a. Fixtures and/or drain inlets subject to backflow and flooding from blocked or restricted public sewers
shall be protected by a backwater valve.
b. Such situations include those where fixtures and/or drains are located above the crown level of the
public sewer at the point of connection thereto, but are below the level ofthe curb at the point where the
building sewer crosses under the curb at the property line.
c. Backwater valves shall be installed in branches ofthe drainage system, which receive flow only from
fixtures and/or drains subject to backflow from the public sewer.
d. Other portions of the drainage system not subject to such backflow shall drain directly to the public
sewer.
5.5.2 Material Standard and Accessibility

Backwater valves shall conform to the standard listed in Table 3.1.3 and shall be installed so that their internal
working parts are accessible for periodic cleaning, repair or replacement.

Liquid Waste Treatment Equipment
6.1 GENERAL
6.1.1 When Required

Interceptors, separators, neutralizers, dilution tanks, or other means shall be provided where required to
prevent liquid wastes containing fats, oils, greases, flammable liquids, sand, solids, acid or alkaline waste,
chemicals, or other harmful substances from entering a building drainage system, a public or private sewer, or
sewage treatment plant or process. See Figure 6.1.1
ACCESS
COVER
OUTLET
INLET OUTLET
(f) INLET
W
...J
"-
"-
REMOVABLE
BASKET
~ ca
ACCESS
COVER
GREASE INTERCEPTOR SOLIDS INTERCEPTOR
ACCESS
COVER
ACCESS
GRATE COVER
INLET OUTLET
OUTLET ADJUSTABLE
OIL
DRAWOFF
SAND INTERCEPTOR OIL INTERCEPTOR
Figure 6.1.1
DIFFERENT TYPES OF INTERCEPTORS
6.1.2 Design
The size and type of liquid waste treatment equipment shall be based on the maximum volume and rate of
discharge of the plumbing fixtures and equipment being drained. See Appendix J.
6.1.3 Exclusion of Other Liquid Wastes

Only wastes from fixtures and equipment requiring treatment or separation shall be discharged into treatment
equipment.

6.1.4 Approval
6.1.4.1 General
The type, size, capacity, design, arrangement, construction, and installation ofliquid waste treatment
devices shall be as approved by the Authority Having Jurisdiction.
6.1.4.2 Grease Interceptors

Grease interceptors rated for up to 50 gallons per minute shall be certified according to PDI Standard
GlO1.
6.1.4.3 Mechanical Equipment

Each installation of a manufactured liquid waste treatment device employing pumps, filters, drums,
collection plates, or other mechanical means of operation shall be certified by the manufacturer to
provide effluent meeting the environmental requirements of the sewer or other approved point to which
it discharges.
6.1.5 Venting
Liquid waste treatment equipment shall be so designed that they will not become air-bound iftight covers are
used. Equipment shall be properly vented ifloss of its trap seal is possible.
6.1.6 Accessibility
a. Liquid waste treatment equipment shall be so installed that it is accessible for the removal of covers and
the performance of necessary cleaning, servicing and maintenance.
b. The need to use ladders or move bulky objects in order to service interceptors and other liquid waste
treatment equipment shall constitute a violation of accessibility.
6.1.7 Point of Discharge

Connections to sewers or other points of discharge for the effluent from liquid waste treatment equipment
shall be as approved by the Authority Having Jurisdiction.
6.2 GREASE INTERCEPTORS
6.2.1 Sizes Up to 50 GPM

Manufactured grease interceptors rated up to 50 gallons per minute shall be sized and installed in accordance
with the recommendations of the manufacturer or PDI Standard G 10 I - Appendix A. They shall have a
grease retention capacity of not less than two pounds for each gpm of rated flow. A flow control device shall
be provided to prevent the waste flow (gpm) through the interceptor from exceeding its rated flow capacity.
An air intake shall be provided for the flow control as recommended by the manufacturer or PDI Standard
G 101 - Appendix A. See Figure 6.2.1 for a flow control device
148 2003 National Standard Pumbing Code~lllustrated

PLUNGER FOR
CLEANING ORIFICE
PACKING GLAND
INLET
VENT
CONNECTION
Figure 6.2.1
A FLOW CONTROL DEVICE FOR A GREASE INTERCEPTOR
6.2.2 Fixture Traps

a. Fixtures that discharge into a grease interceptor shall be individually trapped and vented between the
fixture and the interceptor.
b. When individually trapped and vented fixtures discharge into a grease interceptor, the required vented
flow control device shall be installed between the vented fixture traps and the interceptor.
EXCEPTION: A grease interceptor with the required flow control device shall be permitted to serve as a trap
for an individual fixture ifthe developed length of the drain between the fixture and the interceptor does not
exceed four feet horizontally and 30 inches vertically.

i
I
I
I
AIRINTAKE
FOR I
FLOW CONTROL DEVICE 1--- VENT TO
FIXTURE TRAP I ATMOSPHERE
,
MULTIPLE SINK COMPARTMENTS VENT(S) I
WITH ONE OR MORE VENTED TRAPS
~
:
FLOW
CONTROL:
DEVICE 11
,-
7- I
I
I
~ABOVE
ACCESSIBLE GREASE INTERCEPTOR
OR BELOW FLOOR
I ~I
~, /i
FIXTURE TRAP
~
r
~. WASTE DRAIN
NOTES:
1. Flow control devices are necessaryto prevent the waste flow from exceeding the design flow rating
ofthe grease interceptor.
2. When the fixtures connected to the grease interceptor have traps, the air intake on the flow control
device must be connected to the fixture vent piping system.
3. Air intake through the flow control device aerates the grease-laden waste, which is essential to the
separation process.
Figure 6.2.2 - A
A GREASE INTERCEPTOR SERVING TRAPPED AND VENTED FIXTURES
i
I
AIR INTAKE WITH I
I
~RETURN BEND
SINK OR DISHWASHER I
,--- VENTTO
FIXTURE OVERFLOW LEVEL 7 '" - ~6" MIN. I

,
ATMOSPHERE
~ I
I
I
T ACCESSIBLE GREASE INTERCEPTOR
30"MAX.
J I
FLOW~
CONTROL
DEVICE ~ I
ABOVE OR BELOW FLOOR
L4~'MAX ~ ~ WASTE DRAIN
NOTES:
1. When a fixture that is connected to a grease interceptor is within 4 feet horizontally and 30 inches
vertically from the inlet to the interceptor, a fixture trap is not required. If the fixture is not trapped,
the air intake for the flow control device must not be connected to the vent piping system. It must
be terminated at a 180 degree return bend with its inlet at least 6 inches above the flood level of the
fixture.
Figure 6.2.2 - B
A GREASE INTERCEPTOR SERVING AS A FIXTURE TRAP

6.2.3 Food Waste Grinders
Where food waste grinders discharge through a grease interceptor, a solids interceptor shall be installed
upstream of the grease interceptor to prevent food particles from entering the grease interceptor. See
Figure 6.2.3
T
I
I
AIR INTAKE FOR
1
FIXTURE TRAP
FLOW CONTROL DEVICE
1- VENTTO
VENT(S) : ATMOSPHERE
7 I
J
r i
I I I
SINK- I ACCESSIBLE GREASE INTERCEPTOR
I FLOW I
FOOD WASTE I CONTROL I
GRINDER
DEVICE ~I ~ABOVE OR BELOW FLOOR
SOLIDS SEPARATOR----------
WASTE DRAIN
Figure 6.2.3
A FOOD WASTE GRINDER WITH SOLIDS SEPARATOR AND GREASE INTERCEPTOR
6.2.4 Commercial Dishwashers

Commercial dishwashers shall be permitted to discharge through a grease interceptor.
6.2.5 Location
Grease interceptors shall be permitted to be installed within buildings unless otherwise prohibited by the
Authority Having Jurisdiction. Where interceptors or holding tanks are remote from the fixtures served, the
drain piping between the fixtures and the interceptor or holding tank shall be as direct as possible and shall
include provisions for periodic cleaning.
6.2.6 Prohibited Interceptors

The installation of water-cooled grease interceptors shall be prohibited.
6.2.7 Chemicals Prohibited

The use of enzymes, emulsifiers, or similar chemicals in grease interceptors shall be prohibited.
6.2.8 Individual Dwelling Units

Grease interceptors shall not be required in individual dwelling units or any private living quarters.

6.3 OIL/WATER SEPARATORS
6.3.1 Where Required and Approved Point of Discharge

a. Liquid waste containing grease, oil, solvents, or flammable liquids shall not be directly discharged into
any sanitary sewer, storm sewer, or other point of disposal. Such contaminants shall be removed by an
appropriate separator.
b. Sand interceptors and oil separators shall be provided wherever floors, pits or surface areas subject to
accumulation of grease or oil from service or repair operations are drained or washed into a drainage system.
Such locations include, but are not limited to, car or truck washing facilities, engine cleaning facilities, and
similar operations. The drainage or effluent from such locations shall be connected to the sanitary sewer.
c. Drains shall not be required in service or repair garages that employ dry absorbent cleaning methods;
however, if any drains are located in such areas, they shall discharge to the sanitary sewer through a sand
interceptor and oil interceptor.
d. Drains shall not be required in parking garages unless the garage, or portions thereof, has provisions for
either washing vehicles or rinsing the floor. Where such cleaning facilities are provided, the area subject to
waste drainage shall be provided with one or more floor drains, complete with sand interceptor and oil inter-
ceptor, and the effluent from the oil separator shall be connected to the sanitary sewer. Any storm water shall
be drained separately and directly to the storm sewer.
e. Where parking garages without provisions for vehicle washing or floor rinsing require storm water
drainage, drains shall be permitted to connect to the storm sewer without a sand interceptor and oil separator.
Such drainage, including melting snow, ice or rainwater runoff from vehicles, shall not be connected to the
sanitary sewer.
f. Where oil separators include a waste holding tank, it shall not be used to store or contain any other
waste oil (e.g., motor oil) or hazardous fluid.
6.3.2 Design of Oil Separators

a. Where oil separators are required in garages and service stations, they shall have a minimum volume of
six cubic feet for the first 100 square feet of area drained, plus one cubic foot for each additional 100 square
feet of area drained. Oil separators in other applications shall be sized according to the manufacturers rated
flow.
b. Field-fabricated oil separators shall have a depth of not less than two feet below the invert of the
discharge outlet. The outlet opening shall have a water seal depth of not less than 18 inches.
c. Manufactured oil separators shall be sized according to gallons per minute of rated flow. They shall
include a flow control device and adjustable oil draw-off.
d. Oil separators shall have a 3-inch minimum discharge line and a 2-inch minimum vent to atmosphere.
The discharge line shall have a full-size cleanout extended to grade or otherwise be accessible.
e. The oil draw-off or overflow from oil separators shall be connected to an approved waste oil tank that
meets the environmental requirements of the Authority Having Jurisdiction. The waste oil from the separator
shall flow by gravity or may be pumped to a higher elevation by an automatic pump. Pumps shall be ad-
equately sized, explosion-proof, and accessible. Waste oil tanks shall have a 2-inch minimum pump-out
connection and a 1-1/2 inch minimum vent to atmosphere.
f. Where oil separators are subject to backflow from a sewer or other point of disposal, their discharge
line shall include a backwater valve, installed in accordance with Section 5.5.
g. Where oil separators are installed in parking garages and other areas where the waste flow will include
sand, dirt or similar soilds, a sand interceptor shall be provided upstream from the oil separator. Sand intercep-
tors shall comply with Section 6.4.
h. Oil interceptors, waste oil tanks, oil pump-out connections, backwater valves and atmospheric vent
piping shall be permanently identified by suitable labels or markings.

6.3.3 V apor Venting
The atmospheric vents from oil separators and their waste holding tanks shall be separate from other plumb-
ing system vents and shall be extended to an approved location at least 12 feet above grade or the surround-
mg area.
6.3.4 Combination Oil Separator and Sand Separator

A combination oil separator and sand separator meeting the functional requirements of Sections 6.3 and 6.4
shall be permitted to be installed.
6.4 SAND INTERCEPTORS

a. A sand interceptor shall be installed upstream from an oil separator if required in Section 6.3.2.g.
b. A sand interceptor shall be provided downstream from any drain whose discharge may contain sand,
sediment, or similar matter on a continuing basis that would tend to settle and obstruct the piping in the
drainage system. Multiple floor drains shall be permitted to discharge through one sand interceptor.
6.4.2 Construction and Size

a. Sand interceptors shall be constructed of concrete, brick, fabricated coated steel, or other watertight
material, and shall be internally baffled to provide an inlet section for the accumulation of sediment and a
separate outlet section.
b. The outlet pipe of a sand interceptor shall be the same size as the drain served.
EXCEPTION: If serving an oil separator, the outlet from the sand interceptor shall be the same size as the
inlet to the oil separator.
c. The inlet baffle shall have two top skimming openings, each the same size as the outlet pipe and at the
same invert as the outlet opening. The openings in the baffle shall be offset to prevent straight-line flow
through the interceptor from any of its inlets to its outlet.
d. The inlet to the interceptor shall be at the same elevation as, or higher than, the outlet. The bottom of
the inlet section shall be at least 24 inches below the invert of the outlet pipe.
e. The bottom of the inlet section shall be at least two feet wide and two feet long for flow rates up to 20
gallons per minute. The bottom of the inlet section shall be increased by one square foot for each 5 gpm of
flow or fraction thereof over 20 gpm. The bottom of the outlet section shall be not less than 50% of the area
of the bottom ofthe inlet section.
f. A solid removable cover shall cover the outlet section. An open grating suitable for the traffic in the
area in which it is located shall cover the inlet section. Covers shall be set flush with the finished floor.
See Figures 6.4.2-A and-B

SOLID ACCESS GRADE OR
GRATE\ COVER7 r FLOORLINE
STAGGERED FLOW
OPENINGS~
RI ---- TO OIL I WATER
INLET SEPARATOR
SLIGHTLY
HIGHER
WATERPROOFING
THAN
OUTLET
OUTLET SECTION
SECTION VIEW
NOTES:
1. Where a sand interceptor is installed upstream from an oil separator, the sand interceptor does not
have to include a 6" trap seal depth. The oil separator provides the trap seal that blocks the flow of
sewer gas from the building sewer into the building.
Figure 6.4.2 - A
A SAND INTERCEPTOR SERVING AN OIL SEPARATOR
GRATE AND
ACCESS COVER
REMOVED
L-=-T- LI 00'
SKIMMING
OPENINGS
/ "lL L -.?:::
[==-u n-==-
PLAN VIEW
SOLID REMOVABLE GRADE OR
GRATE \ COVER? r FLOOR LINE
-t~ ii, , I~T~~GE~~~ ~~;' , '. " '. " ,' ,.
INVERT OF OUTLET
INLET ). ~ ~"~I~
.. I SKIMMINGOPENINGSRI OUTLET
WATERPROOFING
OUTLET SECTION
SECTION VIEW
NOTES:
1. Where a stand-alone sand interceptor is installed, it must include a 6" trap seal depth to block the
flow of sewer gas from the building sewer into the building.
Figure 6.4.2 - B
A STAND-ALONE SAND INTERCEPTOR

6.4.3 Water Seal
When a sand interceptor is used separately without also discharging through an oil separator, its outlet pipe
shall be turned down inside the separator below the water level to provide a six-inch minimum water seal. A
cleanout shall be provided for the outlet line.
6.4.4 Alternate Design

Alternate designs for construction of, or baffling in, sand interceptors shall comply with the intent of this Code
and be submitted to the Authority Having Jurisdiction for approval.
6.5 SOLIDS INTERCEPTORS
a. Solids interceptors shall be provided where necessary to prevent harmful solid materials from entering the
drainage system on a continuing basis. Such harmful materials include, but are not limited to, aquarium gravel,
barium, ceramic chips, clay, cotton, denture grin dings, dental silver, fish scales, gauze, glass particles, hair, jewels,
lint, metal grindings, plaster, plastic grindings, precious metal chips, sediment, small stones, and solid food particles.
b. Solids interceptors shall separate solids by gravity, trapping them in a removable bucket or strainer.
c. Solids interceptors shall be sized according to their drain pipe size or by the required flow rate.
6.6 NEUTRALIZING AND DILUTION TANKS
a. Neutralizing or dilution tanks shall be provided where necessary to prevent acidic or alkaline waste from
entering the building drainage system. Such waste shall be neutralized or diluted to levels that are safe for the
piping in the drainage and sewer systems.
b. Vents for neutralizing or dilution tanks shall be constructed of acid-resistant piping and shall be independent
from sanitary system vents.
6.7 SPECIAL APPLICATIONS
6.7.1 Laundries
Commercial laundries shall be equipped with one or more lint interceptors having wire baskets or similar
devices, removable for cleaning, that will prevent passage into the drainage system of solids 1/2 inch or larger
in size, strings, rags, buttons, lint, and other materials that would be detrimental to the drainage system.
6.7.2 Bottling Establishments

Bottling plants shall discharge their process wastes into a solids separator that will retain broken glass and
other solids, before discharging liquid wastes into the drainage system.
6.7.3 Slaughter Houses

Drains in slaughtering rooms and dressing rooms shall be equipped with separators or interceptors, approved
by the Authority Having Jurisdiction, that will prevent the discharge into the drainage system offeathers,
entrails, and other waste materials that are likely to clog the drainage system.
6.7.4 Barber Shops and Beauty Parlors

Shampoo sinks in barbershops, beauty parlors, and other grooming facilities shall have hair interceptors
installed in lieu of regular traps.

Blank Page
156 2003 National Standard Pumbing Code-lllustrated

Plumbing Fixtures, Fixture Fittings and
Plumbing Appliances
7.1 FIXTURE STANDARDS
Plumbing fixtures, plumbing fixture trim, and plumbing appliances shall comply with the standards listed in Table
3.1.3.
7.2 FIXTURES FOR ACCESSIBLE USE
Plumbing fixtures for accessible use and their installation shall confirm to the requirements of the Authority Having
Jurisdiction.
7.3 INSTALLATION
7.3.1 General
Plumbing fixtures, fixture trim, and plumbing appliances shall be installed in accordance with the requirements
of this Code and the manufacturer's instructions and recommendations.
7.3.2 Minimum Clearances

For other than accessible applications, minimum clearances between plumbing fixtures and from fixtures to
adjacent walls shall be in accordance with Figure 7.3.2. See Figure 7.3.2
7.3.3 Access for Cleaning

Plumbing fixtures shall be so installed as to provide access for cleaning the fixture and the surrounding area. I
7.3.4 Securing Floor-Mounted Fixtures

Floor-mounted fixtures shall be securely supported by the floor or floor/wall structure. No strain shall be
transmitted to the connecting piping. Fastening screws or bolts shall be corrosion-resisting.

<t <t
r- -I r-
115"1 I- 30" 1 1 CC~~R
I -j r-
15" OTHER BUILDINGS
12" DWELLINGS
i
jI - t 'WAL~r:~:I
WATERCLOSETS
OR
BIDET
CLEAf[~~JL,:ALL
-I 15" i-
-j3"H 130" 1 130" 1
~
/
WALL
!
i
~W~
T
21"
CLEARANCE
I
' 1
,
I URINALS
!
1
'
I
~ 1
i
w.c.1
14"1 14"1
:/::;:>?:,:./:>:::>;:>;;;;/:;x,:>:/;;:.::;x,;;;<::;<:.
14"1 112"
21" , ~
IlJ r
WALLiCLEARANCEI-- 30" --j
,
r
~ 1 w,c. I
-~W~~:I 1
/,
I T i
LAVATORIES
i i i i
r\7I
UJ The clear height between ceilings and
floors shall comply to the requirement of
the Building Code.
24" CLEARENCE IN FRONT OF OPENING
Figure 7.3.2
MINIMUM FIXTURE CLEARANCES

7.3.5 Supporting Wall-Hung Fixtures
a. Wall-hung water closets shall be supported by concealed metal carriers that transmit the entire weight
of the fixture to the floor and place no strain on the wall or connecting piping. Supports of this design shall
comply with ASME AI12.6.1.
b. Free-standing lavatories, wall-hung urinals, water closets with or without concealed tanks and other
wall-mounted fixtures shall be supported by a concealed or exposed finished wall hanger plate or equivalent
that transmits the weight of the fixture to the wall structure, if adequate, or to the floor without placing strain
on the piping. Such supports shall comply with ASME AlI2.6.2 or ASME AlI2.19.12. In addition to the wall
support brackets, pedestals or legs may provide additional support for pedestal lavatories.
See Figure 7.3.5
l
CARRIER BODY
ALL
o\
I/
l~
~SUPPORT ISENTIRELY
CARRIERBOLTS
\~\
\~
ON
r::',,'\'.:,:,':..
I .,,~\
"--LAG SCREW AND ANCHOR
NOTES:
1. Wall hung water closets are designed to be supported by carriers,
2. For fixtures other than water closets, such as lavatories and urinals, the carrier may be either floor
or wall supported, depending on the strength of the wall.
Figure 7.3.5
A CARRIER FOR A WALL HUNG WATER CLOSET
7.3.6 Orientation and Operation of Faucets

Where fixtures are supplied with both hot and cold water, the faucet(s) and supply piping shall be installed so
that the hot water is controlled from the left side of the fixture or faucet when facing the controls during
fixture use.
EXCEPTION: Single handle and single control valves for showers and tub/shower combinations where the
hot and cold temperature orientation is marked on the fitting surface.
7.3.7 Access to Concealed Connections

Where fixtures have drains with concealed slip joint connections or incorporate a cleanout plug, a means of
access shall be provided for inspection and repair. Such access is not required for connections that are
soldered, threaded, solvent cemented, or equivalently secured.
Comment: Access to concealed slipjoints and cleanouts can require the use of tools.

7.3.8 Joints with Walls and Floors
Jointswherefixturescontactwallsandfloorsshallbe caulkedor otherwisemadewater-tight. See Figure
7.3.8
SEAL EDGES
%1
//
/- AND SIDES
''/:
,/
~/
;;
'/
LAVATORY WALL HUNG URINAL
SEAL EDGES
;;
//
;:,/
;;/
;;;
j ~ AND SIDES
//
//
SEAL EDGES
~;
//
//
//
//:
:*~~:<>~':::::<~<:">
r AROUNDBASE
WALL HUNG WATER CLOSET FLOOR MOUNTED WATER CLOSET
~ ~ r SEAL
EDGES
AND AT
FLOOR
SHOWER STALL BATHTUB

NOTES:
1, Openings or gaps between fixtures and walls or floors can collect dirt and moisture. They are
unsanitary and can cause water damage to the building structure. These openings must be caulked
or otherwise sealed.
Figure 7.3.8
SEALING FIXTURES TO WALLS AND FLOORS
7.4 WATER CLOSETS
7.4.1 Compliance
Vitreous china water closets shall comply with ANSI/ASME A 112.19.2M. Plastic water closets shall comply
with ANSI 2124.4.
7.4.2 Water Conservation

Water closets, whether operated by flush tank, flushometer tank, or flushometer valve, shall comply with
ANSI/ASME A 112.19.2M and shall be the low-consumption type having an average consumption of not
more than 1.6 gallons per flush when tested in accordance with ANSI/ASME AI12.l9.6.
EXCEPTION: Blow-out water closets and clinical sinks.

7.4.3 Contour of Bowls
Water closets shall have elongated bowls with open-front seats.
EXCEPTIONS:
(1) Water closets having closed-front seats and either round or elongated bowls shall be permitted in
dwelling units.
(2) Water closets having closed-front seats which are protected by automated seat cover protection.
(3) A water closet in a private office toilet room, intended for the exclusive use of one individual.
(4) Water closets intended for use in pre-school and kindergarten facilities.
r-- ELONGATED
/ BOWL
I
.,,:mI.- R'M
W
I
131/2" MINIMUM
(SEE EXCEPTIONS IN
FIGURES 7.4.4-A and
7.4.4-B)
NOTES:
1. See Figure 7.4.4 - A for bowl heights for children's use.
2. See Figure 7.4.4 - B for bowl heights for adult accessible use.
Figure 7.4.3 - A
AN ADULT-HEIGHT ELONGATED WATER CLOSET BOWL
COMPARED TO A ROUND BOWL
A--'..
'.. '..
'.. '..
'.. '..
'.. '..
'.. '..
'.. '..
\ "
I'
'.."
t::::::=
,,-
~ ~/
)_1_-
-
' '..
-1-1
--y--
I
' '.. I
'.. ~//. I
'.. /
" / I
"', <// .' /., // ......
NOTES:
1. Seats for water closets must fit the water closet bowl. Section 7.4.5 requires elongated seats on
elongated bowls and round seats on round bowls.
Figure 7.4.3 - B
AN OPEN FRONT ELONGATED WATER CLOSET SEAT (LESS LID)

7.4.4 BowlHeight
The height of water closet bowls shall be a minimum of 13Yzinches from the floor to the top ofthe rim.
EXCEPTIONS:
(1) Bowls intended specifically for children's use shall be 9Yzto 10Yzinches high and juvenile use shall be
1OYzto 13Yzinches high.
(2) Bowls intended specifically for accessible or elderly use shall be at least 17 inches high and comply
with Section 7.2.
See Figures 7.4.3-A, 7.4.4-A, and 7.4.4-B.
APPLICATION AGE - YEARS HEIGHT "H"

CHILDREN'SUSE 5 & YOUNGER 9-1/2"TO 10-1/2"TO RIM
JUVENILE(CHILDREN'S)USE 6-12 10-1/2"TO 13-1/2"TO RIM
ACCESSIBLECHILDREN'SUSE 12 & YOUNGER 11"TO 17"TO TOP OF SEAT
"H"
Figure 7.4.4 - A
HEIGHTS OF WATER CLOSET BOWLS FOR CHILDREN'S USE
ITOPOFS~T
17" - 19"
Figure 7.4.4 - B
HEIGHT OF WATER CLOSET BOWLS FOR ADULT ACCESSIBLE USE

7.4.5 Water Closet Seats
Seats for water closets shall be of smooth, non-absorbent materials, be properly sized to fit the water closet
bowl, and comply with ANSI 2124.5
EXCEPTION: Water closet seats in dwelling units are not required to comply with ANSI 2124.5.
7.4.6 Hotels, Motels, Dormitories, and Boarding Houses

Water closets in hotels, motels, dormitories, boarding houses and similar occupancies shall be the elongated
type complying with ASME AI12.19.2 or ANSI 2124.4, and ASME Al12.19.6 and with open-front seats
complying with ANSI 2124.5
EXCEPTION:
(1) Closed-front seats shall be permitted in hotel and motel guest rooms.
(2) Closed-front seats which are provided with automatic seat cover protection.
7.4.7 Prohibited Water Closets

Water closets not having a visible trap seal or having either unventilated spaces or walls that are not washed
at each discharge shall be prohibited.
7.5 URINALS
7.5.1 Compliance
a. Urinals with a non-visible water trap seal and/or strainer shall be equipped with an automatic flushing
device.
b. Vitreous china urinals shall comply with ANSI/ASME Al12.19.2.
c. Plastic urinals, including female urinals, urinals for the physically impaired, and waterless male urinals,
shall comply with ANSI 2124.9.

Water-fed urinals shall be the low-consumption type having an average water consumption of not more than
1.0 gallon per flush when tested in accordance with ANSI/ASME AI12.9.6.
7.5.3 Surrounding Surfaces

Wall and floor surfaces shall be waterproof and have a smooth, readily cleanable, non-absorbent surface
extending not less than four feet above the floor and one foot to each side of a urinal, and one foot in front of
the lip of a urinal. See Figure 7.5.3

1'-0" 1'-0"
@
~ AREA WHICH
" MUSTBE
COVERED WITH
A WATERPROOF
MATERIAL
4'-0"
1'-0"
12" FROM LIP OF URINAL
Figure 7.5.3
PROTECTING SURROUNDING SURFACES AT URINALS
7.5.4 Prohibited Urinals

Trough urinals and urinals having walls that are not washed at each discharge shall be prohibited.
EXCEPTION: Waterless urinals complying with ANSI ZI24.9.
7.6 LAVATORIES
7.6.1 Compliance
a. Lavatories shall comply with the following standards:
1. Ceramic, non-vitreous; ANSI/ASME AI12.19.9M
2. Enameled cast-iron; ANSI/ASME AI12.19.1M
3. Enameled steel; ANSI/ASME AI12.19.4M
4. Plastic; ANSI Z124.3
5. Stainless steel; ANSIIASME AI12.19.3M
6. Vitreous china; ANSI/ASME A112. 19.2M

a. Except as required under Section 7.6.2.b, lavatory faucets shall be designed and manufactured so that

they will not exceed a water flow rate of2.2 gallons per minute when tested in accordance with ANSI/
ASME AI12.18.1.
b. Self-closing or self-closing/metering faucets shall be installed on lavatories intended to serve the tran-
sient public, such as those in, but not limited to, service stations, train stations, airport terminals, restaurants,
and convention halls. Metering faucets shall deliver not more than 0.25 gallon of water per use when tested in
accordance with ANSI! ASME A 112.18.1. Self-closing faucets shall be designed and manufactured so that
they will not exceed a water flow rate of 0.5 gallon per minute when tested in accordance with ANSI/ ASME
AI12.l8.1.
7.6.3 Waste Outlet

The waste outlet pipe on individual lavatories shall be not less than 1-1/4" nominal size. A strainer, pop-up
stopper, crossbar grid, or other device shall be provided to protect the waste outlet.
7.6.4 Integral Overflow

Where lavatories include an integral overflow drain, the waste fitting shall be designed and installed so that
standing water in the bowl of the fixture cannot rise in the overflow channel when the drain is closed, nor
shall any water remain in the overflow channel when the bowl is empty. The overflow shall drain to the inlet
side of the fixture trap. See Figure 7.6.4
Comment: Overflows are not provided in all lavatories. Lavatories with overflows are not used in
hospitals because of the potentially unsanitary condition caused by inaccessible surfaces exposed to
waste.
OVERFLOW OPENING
(WHERE PROVIDED) ~
7
POP-UP WASTE Tf
;!!
, ~ OVERFLOW TO DISCHARGE INTO
FIXTURE SIDE OF TRAP
POP-UP LEVER
Figure 7.6.4
A LAVATORY OVERFLOW
7.6.5 Lavatory Equivalent

Where group-type wash fountains or wash sinks are used to satisfy the number of lavatories required by
7.21.1, each 18-inchusable length of rim having an available water spray shall be considered as one lavatory.
See Figure 7.6.5

'~
::~~:'oJ;'':""
TI.:...:.:.
. -::::'::
PLAN ELEVATION
Figure 7.6.5
A CIRCULAR WASH FOUNTAIN
7.7 BIDETS
7.7.1 Compliance
Vitreous china bidets shall comply with ANSI/ASME Al12.19.2M
7.7.2 Backflow Prevention

Bidets having integral flushing rims shall have a vacuum breaker assembly on the mixed water supply to the
fixture. Bidets without flushing rims shall have an over-the-rim supply fitting providing the air gap required by
Chapter 1O.
7.7.3 IntegralOverflow
Where bidets include an integral overflow drain, the waste fitting shall be designed and installed so that
standing water in the bowl of the fixture cannot rise in the overflow channel when the drain is closed, nor
shall any water remain in the overflow channel when the bowl is empty. The overflow shall drain to the inlet
side of the fixture trap.
7.8 BATHTUBS
7.8.1 Compliance
a. Bathtubs shall comply with the following standards:
1. Plastic, cultured marble and other synthetic products or finishes; ANSI Z 124.1
2. Enameled cast-iron; ANSI/ASME Al12.19.1
3. Enameled steel; ANSI/ASME Al12.19.4
4. Bathtubs with pressure sealed doors; ASME Al12.19.15
7.8.2 Waste and Overflow

Bathtubs shall have waste outlet and overflow pipes not less than 1-1/2"nominal size. Waste outlets shall be
equipped with a pop-up waste, chain and stopper, or other type of drain plug. See Figure 7.8.2

/
/,
- TRIP LEVER
~ OVERFLOW TO DISCHARGE INTO

FIXTURE SIDE OF TRAP
1Y:,-
POP-UP WASTE SHOWN
Figure 7.8.2
A BATHTUB WASTE AND OVERFLOW
7.8.3 Combination Bath/Showers

Shower heads shall be designed and manufactured so that they will not exceed a water supply flow rate of
2.5 gallons per minute when tested in accordance with ANSI! AS ME A 112.18.1. The control of mixed water
temperatures to bath/shower combinations shall comply withe Section 10.15.6. Surrounding wall construction
shall be in accordance with Section 7.IO.5.b. Riser pipes to shower heads shall be secured in accordance
with Section 7.10.7. Control valves and shower heads shall be located in accordance with Section 7.10.8.
7.8.4 Backflow Prevention

Unless equipped with an atmospheric backflow preventer in accordance with ASSE 1001 or AS ME
AII2.18. 7, the bathtub filler shall be equipped with an air gap between the end of the over-rim tub filler spout
and the overflow rim of the tub which shall comply with Section 10.5.
7.9 WHIRLPOOL BATHS
7.9.1 General
The requirements of Section 7.8 for bathtubs shall also apply to whirlpool baths. The provisions for wet
venting in Section 12.10shall also apply to whirlpool baths.
7.9.2 Compliance
Whirlpool bathtubs shall complywith ANSI!ASME A 112.19.7M.
7.9.3 Drainage
The arrangements of circulating piping and pumps shall not be altered in any way that would prevent the
pump and associated piping from draining after each use of the fixture.
7.9.4 Access
One or more removable panels shall be provided where required for access to pumps, heaters, and controls,
as recommended by the fixture manufacturer. See Figure 7.9.4

ACCESS REQUIRED
AS R~COMM~ND~D
BY THE MANUFACTURER
NOTES:
1. Access must be provided to electrical and plumbing components of whirlpool baths as recom-
mended by the manufacturer. Referto manufacturer's installation instructions.
Figure 7.9.4
ACCESS REQUIREMENTS FOR A WHIRLPOOL BATH
7.10 SHOWERS
7.10.1Compliance
Plastic shower receptors and stalls shall comply with ANSI Z 124.2.

Shower heads shall be designed and manufactured so that they will not exceed the flow rate for shower head specified in
ANSVASMEAI12.l8.IM.
EXCEPTION:Emergencysafetyshowers.
7.10.3 Control ofMixed Water Temperature

The control of mixed water temperatures shall comply with Section 10.15.6.
7.10.4 Shower Waste Outlet

a. The waste outlet connection for showers shall be not less than 2 inches nominal size and have a removable strainer
not less than 3 inches in diameter with 1/4" minimum openings.
EXCEPTION: Bathubs with overhead showers.
b. Waste outlets shall be securely connected to the drainage system.
c. In group showers where each shower space is not provided with an individual waste outlet, the waste outlet(s)
shall be so located and the floor so pitched that waste water ITom one outlet does not flow over the floor area serving
another outlet.
7.10.5 Shower Compartments

a. Individual shower compartments shall have a minimum of 1024 square inches of interior cross-sectional area.
b. The minimum interior dimensions of the shower compartment shall be not less than 30 inches measured ITom its
finished interior as the side of a rectangle, altitude of a triangle, diameter of a circle, or other angular shape.
c. The minimum required area and dimensions shall be measured at a height equal to the top of the threshold, and
maintained to a height of not less than 70 inches above the floor of the compartment or receptor, measured at the drain.
d. Fold-down seats shall be permitted in showers, provided the required cross-sectional area requirements as defined
in (A) (B) and (C) above, are met when the seat is in the folded-up position.
e. The walls in shower compartments and above built-in bathtubs having installed shower heads shall be constructed
of smooth, non-corrosive, non- absorbent waterproof materials that extend to a height of not less than 72 inches above
the floor ofthe room and not less thatn 70 inches above the floor of the compartment, shower pan, or tub measured from
the drain.
f. The joints between walls and with bathtubs and shower compartment floors shall be water-tight.
EXCEPTIONS:
(I) Only the shower valve or valves, showerhead, soap dish, and grab bars or rails may protrude into the required
area and dimensions.
(2) The dimensional requirements of Section 7.10.5 shall not apply to bathtubs or whirlpool baths having overhead
showerheads.

(3) Rectangular shower compartments may have a minimum rough-in dimension of27 inches in width provided the
length has a minimum 48-inch rough-in dimension and an interior finished area of not less than 1150 square inches.
(4) In the case where an existing bathtub is replaced by a shower compartment and the dimensional requirements of
Section 7.10.5.1.B. cannot be met, the minimum dimension shall be permitted to be 25 inches, provided that the cross-
sectional area is at least 1024 square inches.
(5) Prefabricated shower units designed to accommodate a nominal rough-in opening of32" x 32" minimum shall be
acceptable, provided such units have at least 900 square inches interior area measured from sidewall to sidewall and
back-wall to the center of the threshold, at the elevation at the top of the threshold.
7.10.6 Shower Floors or Receptors

a. Floors or receptors for shower compartments shall be laid on or be supported by a smooth and structurally sound
base.
b. Shower pans shall be provided under the floors of shower compartments.
EXCEPTION:
Shower pans shall not be required when prefabricated shower receptors are used.
c. Shower pans shall form a watertight lining beneath the shower floor.
d. Shower pans shall turn up at least 2 inches above the finished threshold level on all sides.
e. Shower pans shall be securely fastened to the shower waste outlet at the seepage entrance, making a watertight
joint between the pan and the waste outlet.
f. Finished shower floor surfaces shall be smooth, non-corrosive, non-absorbent, and waterproof.
See Figure 7.10.6
/ WATERPROOF MEMBRANE AT LEAST 2"

/' MINIMUM ABOVE THRESHOLD HEIGHT
FLUSH WITH FINISHED SURFACE
I /
./ FINISHED SURFACE
GRADED TO DRAIN
WEEP HO
SECOND
A
':; 6~NAGE~~
~~ . - r CLAMPING RING
I
rWATERPROOF PAN OR LINER
UNDER CLAMPING RING
SHOWER DRAIN DETAIL
Figure 7.10.6
A SHOWER PAN AND DRAIN

7.10.7 WaterSupplyRiser
Whether exposed or concealed, the water supply riser pipe from the shower control valve(s) to the shower
head outlet shall be secured to the wall structure. See Figure 7.10.7
SECURELY SUPPORTED
WITH DROP EAR ELL
AL TERNA TE
ARRANGEMENT
TO SHOWER VALVE-----
~ WATERPROOF
VALVE
/' / WALL (Section 7.10.5)
BODY ~
~ SHOWER CONTROL VALVE
TOP OF BATHTUB
~,
~ SEALED
(Section 7.3.8)
Figure 7.10.7
A SHOWER HEAD SVPPL Y RISER PIPE
7.11 SINKS
7.11.1 Compliance
Sinks shall comply with the following standards:
1. Enameled cast-iron; ANSI/ASME AI12.l9.l M
2. Enameled steel; ANSI/ASME AI12.l9.4M
3. Stainless steel; ANSI/ASME AI12.19.3M
4. Plastic; ANSI 2124.6.
7.11.2 Kitchen Sinks and Bar Sinks

a. Each compartment in a kitchen sink or bar sink shall have a 3-1/2" diameter outlet opening, suitable for
either a domestic food waste grinder or a basket strainer. The waste outlet pipe for each compartment shall
be 1-1/2"nominal size. Outlet fittings shall have crossbars or other provisions for protecting the drain outlet
and shall include a means of closing the drain outlet.
b. Faucets for kitchen sinks and bar sinks shall be designed and manufactured so that they will not exceed
a water flow rate of2.2 gallons per minute when tested in accordance with ANSI/ASME AI12.18.IM.
See Figure 7.11.2

F F~~~~:P =l
BASKET STRAINER J --- DOMESTIC FOOD
WASTE GRINDER
CONTINUOUS~
WASTE
ASSEMBLY TRAP
Figure 7.11.2
KITCHEN SINK DRAIN OUTLETS
7.11.3 LaundrySinks
Sinks for laundry use shall be not less than 12 inches deep with a strainer and waste outlet connection not less
than 1-1/2"nominal size.
7.11.4 Service Sinks and Mop Receptors

a. Service sinks and mop receptors shall have removable strainers and waste outlet connections not less
than 2" nominal size.
b. Walls and floors shall be waterproof and have a smooth, readily cleanable surface within I foot in front
of service sinks and mop sinks, within 1 foot of each side, and up to a point not less than I foot above the
faucet height.
7.11.5 Sink Faucets

a. Sink faucets having a hose thread or other means of attaching a hose to the outlet shall be protected
from back-siphonage by either an integral vacuum breaker, an atmospheric vacuum breaker attached to the
outlet, or pressure-type vacuum breakers on the fixture supply lines.
b. Faucets for kitchen sinks shall be designed and manufactured so that they will not exceed the flow rate
for kitchen faucet specified in ANSI! ASME A 112.18.1 M.
7.11.6 Temperature Actuated Flow Reduction Devices

Where temperature actuated flow reduction devices are installed in conjunction with bathtub spouts,
showerheads, kitchen, bar or service sink fittings, such devices shall comply with ASSE 1062 as listed in
Table 3.1.3. Such devices shall not be a substitute for the requirements in Section 10.15.6.
7.11.7 In-line Pressure Balancing Devices

Where in-line pressure balancing devices are installed to compensate for pressure disturbances to stabilize
temperature discharges from fixture fittings, such devices shall comply with ASME 1066as listed in Table

3.1.3. Such devices shall not be a substitute for the requirements in Section 10.15.6.
7.12 DRINKING FOUNTAINS AND WATER COOLERS
7.12.1 Compliance
Refrigerated drinking fountains and water coolers shall comply with ANSI/ARI 1010 and ANSI/UL 399.
7.12.2 Prohibited Locations

Drinking fountains or water coolers shall not be located in public toilet rooms.
EXCEPTION: Convertible lavatory faucets and fixture fittings that provide a discharge stream similar to a
drinking fountain shall be permitted in bathrooms in dwelling units.
7.13 AUTOMATIC CLOTHES WASHERS
7.13.1 Compliance
Automatic clothes washers shall comply with ANSI/AHAM HLW-2PR or ANSI/ASSE 1007, and shall have
an air gap incorporated in the internal tub fill line.
Comment: Automatic clothes washers that comply with the referenced appliance standards include an
internal air gap in the waterfil/line and do not require the instal/ation of an external backjlow preven-
tion device.
7.14 FOOD-WASTE-GRINDER UNITS
7.14.1 Compliance
Domestic food-waste-grinder units shall comply with ANSI/UL 430 and either AHAM FWD-I, ASSE 1008,
or ANSI!ASSE 1008.
7.14.2 Domestic Units

Domestic food-waste-grinder units shall have not less than a 1-1/2" nominal waste connection to the drainage
system. Such units may connect to a kitchen sink drain outlet, as permitted under Section 7.II.2.a.
7.14.3 Commercial Units

Commercial food-waste-grinder units shall be connected to the drainage system and be separately trapped
from any sink compartment or other fixture. The waste pipe size for such fixtures shall be of sufficient size to
serve the fixture but shall be not less than 2-inch nominal size. See Figure 7.14.3

r VACUUM BREAKER
II
6" MINIMUM
/'
~WATERINLET
(where provided) - SINK OR INLET CONE
_~.D.
- SOLENOID
VALVE
2" DISCHARGE --.....
--- COMMERCIALFOOD
WASTE GRINDER
2" MINIMUM WASTE
t
WATER
2" MINIMUM TRAP
SUPPLY
NOTES:
1. The water supply to a commercial food waste grinder must be protected against back-siphonage by
a vacuum breaker.
Figure 7.14.3
A COMMERCIAL FOOD WASTE GRINDER INSTALLATION
7.14.4 WaterSupply
An adequate supply of water shall be provided for proper operation offood-waste-grinders.
7.15 DISHWASHING MACHINES
7.15.1 Compliance
Domestic dishwashing machines shall comply with ANSI/UL 749 and either ANSI/AHAM DW-2PR or
ANSI! ASSE 1006. Commercial dishwashing machines shall comply with ANSI!UL 921 and ANSI! ASSE
1004. The water supply to dishwashing machines shall be protected from back-siphonage by an integral air
gap or other internal means.
7.15.2 Residential Sink and Dishwasher

The discharge from a residential kitchen sink and dishwasher may discharge through a single 1-1/2" trap. The
discharge line from the dishwasher shall be not less than 3/4" nominal size and shall either be looped up and
securely fastened to the underside of the counter or be connected to a deck-mounted dishwasher air gap
fitting. The discharge shall then be connected to a wye fitting between the sink waste outlet and the trap inlet.
See Figure 7.15.2

~ ~,
(, '\ ALTERNATE DECK-MOUNTED \

\ DISHWASHER AIR GAP FITTING,
I,
I /
tt I'I
\
TO SINK TRAP
FROM DISHWASHER
)
' ~\
COUNTERTOP~
1
SINK
I (~I
'\--
/ n TUBINGLOOPEDUP HIGH AND FASTENED
TO UNDERSIDEOF COUNTER
Figure 7.15.2
A RESIDENTIAL KITCHEN SINK AND DISHWASHER
7.15.3 Residential Sink, Dishwasher, and Food-Waste-Grinder

The discharge from a residential kitchen sink, dishwasher, and food-waste-grinder may discharge through a
single 1-1/2" trap. The discharge from the dishwasher shall be not less than 3/4" nominal size and shall either
be looped up and securely fastened to the underside of the counter or be connected to a deck-mounted
dishwasher air gap fitting. The discharge shall then be connected either to the chamber of the food-waste-
grinder or to a wye fitting between the food-waste-grinder outlet and the trap inlet. See Figure 7.15.3
~ ,
(
I '\ ALTERNATE DECK-MOUNTED \
\ DISHWASHER AIR GAP FITTING
/
TO SINK TRAP
t t
I
!
~' FROMDISHWASHER <

)
/
COUNTER TOP ~
~I r \
,
HOSE LOOPED UP HIGH AND FASTENED
TO UNDERSIDE OF COUNTER
Figure 7.15.3
A RESIDENTIAL KITCHEN SINK, DISHWASHER, AND FOOD WASTE DISPOSAL
174 2003 National Standard Pumbing Code-/1/ustrated

7.15.4 CommercialDishwashingMachine
a. Commercial dishwashing machines shall be indirectly connected to the drainage system through either
an air gap or an air break. When the machine is within 5 feet developed length of a trapped and vented floor
drain, an indirect waste pipe from the dishwasher may be connected to the inlet side of the floor drain trap.
b. Commercial dishwashers shall be permitted to discharge through a grease interceptor in accordance
with Section 6.2.4. See Figure 7.15.4
I PRE-RINSE SPRAY
I VACUUM BREAKER NOT REQUIRED IF AIR GAP IS MAINTAINED
COMMERCIAL
DISHWASHER
D
I ALTERNATE ARRANGEMENT
~/ U
AIRGAPORAIR BREAK ~\ (cccctcccccc'F'--- VENTED

RECEPTOR
VENTED RECEPTOR~\
~ I SFEET MA)(
DEVELOPED
LENGTH
i(:--'
r--
Figure 7.15.4
A COMMERCIAL DISHW ASHING MACHINE
7.16 FLOOR AND TRENCH DRAINS
7.16.1 Compliance
Floor and trench drains shall comply with ASME Al 12.21.1.
7.16.2 TrapSealandStrainer
a. Floor drains shall have a water seal of not less than 2 inches and shall be fitted with a removable
strainer. The free open area of strainers shall be at least 2/3 of the cross-sectional area of the nominal drain
outlet size.
b. Where inftequently used floor drains are subject to evaporation of their trap seals, they shall either I) be
provided with a 4-inch trap seal, 2) be fed from an automatic trap priming device, or 3) be arranged as
otherwise approved by the Authority Having Jurisdiction.
See Figures 7.16.2-A through-C

-- GRATE MINIMUM AREA
MUST COMPLY WITH
A112.21.2M BASED ON
THE DRAINOUTLET SIZE
Figure 7.16.2 - A
A FLOOR DRAIN TRAP AND STRAINER
Figure 7.16.2 - B
A DEEP SEAL TRAP
~ TRAP
BACKFLOWPRIMING DEVICE WITH
PROTECTION
WATER SUPPLY /' (fixture branch type shown)

TO FIXTURE
r FLOOR DRAIN EQUIPPED

WITH PRIMER TRAPPING
NOTES:
1. A fixture branch type trap primer can prime more than one trap if it is fitted with a multi-outlet
manifold.
Figure 7.16.2 C -
A FLOOR DRAIN WITH TRAP PRIMER

7.16.3 Size of Floor Drains
Floor drains and their branch piping shall be sized on the basis of their normal, expected flow rate. Floor
drains shall be not less than 2" nominal size.
7.16.4 Required Locations for Floor Drains

a. Floor drains shall be installed in the following areas:
1. Toilet rooms containing either two or more water closets or urinals or a combination of one or more
water closets and urinals, except in a dwelling unit.
2. Commercial kitchens.
3. Common laundry rooms in commercial buildings and buildings having more than two dwelling units.
4. Where required to accept indirect wastes.
7.16.5 Walk-in Coolers and Freezers

Floor drains located in walk-in coolers and walk-in freezers where food or other products for human con-
sumption are stored shall be indirectly connected to the drainage system in accordance with Section 9.1.6.
7.16.6 FloorSlope
Floors shall be sloped to floor drains where drainage occurs on a regular or frequent basis, or as otherwise
required by the Authority Having Jurisdiction.
7.17 GARBAGE CAN WASHERS
Garbage can washers shall include a removable basket or strainer to prevent large particles of garbage from
entering the drainage system. The water supply connection shall be protected from back-siphonage in accordance
with Chapter 10. Garbage can washers shall be trapped and vented as required for floor drains. See Figure 7.17
'"
L.
~ SEEPAGE OPENINGS
,~ ,.,
"- COLLAR CAN BE USED AS
FLASHING CLAMP
(when required)
/L-- STRAINER BUCKET
Figure 7.17
A GARBAGE CAN WASHER

7.18 SPECIAL INSTALLATIONS
7.18.1 Protection ofWater Supply

The water supply to special installations shall be protected from backflow in accordance with Chapter 10.
Examples of such special installations include decorative fountains, ornamental pools, waterfalls, swimming
and wading pools, baptisteries, and similar custom-built equipment.
7.18.2 Approval
Special installations requiring water supply and/or drainage shall be submitted to the Authority Having Juris-
diction for approval.
7.19 FLUSHING DEVICES FOR WATER CLOSETS AND URINALS
7.19.1 General
Appropriate flushing devices shall be provided for water closets, urinals, clinical sinks, and other fixtures that
depend on trap siphonage to discharge the contents of the fixture.
7.19.2 Separate Devices

A separate flushing device shall be provided for each fixture.
EXCEPTION: A single device may be used to automatically flush two or more urinals.
7.19.3 Flush Tanks

a. Flush tanks shall have ballcocks or other means to refill the tank after each discharge and to shutoff the
water supply when the tank reaches the proper operating level. Ballcocks shall be the anti-siphon type and
comply with ANSI/ ASSE 1002.
b. Except in approved water closet and flush tank designs, the seat of the tank flush valve shall be at least
1 inch above the flood level rim of the fixture bowl.
c. The flush valve shall be designed so that it will close tightly ifthe tank is flushed when the fixture drain
is clogged or partly restricted, so that water will not spill continuously over the rim of the bowl or backflow
from the bowl to the flush tank.
d. Flush tanks shall include a means of overflow into the fixture served having sufficient capacity to
prevent the tanks from overflowing with normal flow through the fill valve.
See Figure 7.19.3

REFill TUBE
TO OVERFLOW
REFill TUBE
TO OVERFLOW
Fill TUBE
\ FLOAT MECHANISM
~
FLUSH VALVE
Fill TUBE
ASSEMBL Y
WATERSUPPlY WATER SUPPLY
Figure 7.19.3
FLUSH VALVES FOR WATER CLOSET FLUSH TANKS
7.19.4 FlushometerTanks
Flushometer tanks shall complywith ASSE 1037and shall include built-in pressure regulation and backflow
prevention devices. See Figure 1.2.34
7.19.5 FlushometerValves
Flushometer valves shall comply with ANSI/ASSE 1037and include a vacuum breaker assembly and means
of flowadjustment.Flushometervalvesshallbe accessiblefor maintenanceand repair. See Figure 7.19.5
~ PUSH BUTTON OPERATED

/ FLUSHOMETER WITH
VACUUM BREAKER
~ HIGH SECURITY
/' WATER CLOSET
TYPICAL INSTAllATION HIGH SECURITY INSTAllATION

NOTES:
1. Flushometer valves are permitted to be installed in an accessible plumbing chase where security is
required in detention and correctional institutions.
Figure 7.19.5
FLUSHOMETER VALVE INSTALLATIONS

7.19.6 Required Water Pressure
The available water supply pressure shall be adequate for proper operation of the particular flushing devices
used, as recommended by the manufacturer.
NOTE: Some one-piece tank-type water closets require 30 psig flowing pressure and 1/2" supplies for proper
operation.
7.20 FIXTURES FOR DETENTION AND CORRECTIONAL INSTITUTIONS
Special design fixtures for use in detention and correctional institutions shall comply with the requirements of this
Code except that fixtures may be fabricated from welded seamless stainless steel and be equipped with necessary
security devices. Water closets shall be the elongated type with integral or separate seats. Urinals shall have a
ontinuous flushing rim that washes all four walls of the fixture.
7.21 MINIMUM NUMBER OF REQUIRED FIXTURES
7.21.1 Number of Fixtures

Plumbing fixtures shall be provided for the type of building occupancy and in the numbers not less than those
shown in Tables 7.21.1.
7.21.2 Occupant Load

a.The minimum number of plumbing fixtures shall be based on the number of persons to be served by the
fixtures, as determined by the person responsible for the design ofthe plumbing system.
b. Where the occupant load is not established and is based on the egress requirements of a building code,
the number of occupants for plumbing purposes shall be permitted to be reduced to two-thirds ofthat for fire
or life safety purposes.
c. Whenever both sexes are present in approximately equal numbers, the total occupant load shall be
multiplied by 60 percent to determine the number of persons of each sex to be provided for, unless specific
information concerning the percentage of male and female occupants is available.
d. Plans for plumbing systems, where required, shall indicate the maximum number of persons to be
served by the facilities.
e. In occupancies having established seating, such as auditoriums and restaurants, the number of occu-
pants for plumbing purposes shall not be less than the number of seats.
7.21.3 Access to Fixtures

a. In multi-story buildings, accessibility to the required fixtures shall not exceed one vertical story.
b. Fixtures accessible only to private offices shall not be counted to determine compliance with this
section.
c. The lavatories required by Tables 7.21.1 shall be located within the same toilet facility as their associ-
ated water closets and urinals.

7.21.4 Separate Facilities
Separate toilet facilities shall be provided for each sex.
EXCEPTIONS:
1. Residential installations.
2. In occupancies serving 10 or fewer people, one toilet facility, designed for use by no more than one
person at a time, shall be permitted for use by both sexes.
3. In businesses, occupancies with a total floor area of 1500 square feet or less, one toilet facility, de-
signed for use by no more than one person at a time, shall satisfy the requirements for serving customers and
employees of both sexes.
4. In mercantile occupancies with a net occupiable floor area of 1500 square feet or less that is accessible
to customers, one toilet facility designed for use by no more than one person at a time, shall satisfy the
requirements for serving customers and employees of both sexes.
7.21.5 Substitution and Omission of Fixtures

a. Urinals: Not more than 50% of the required number of water closets may be substituted with urinals.
b. Drinking Water Facilities: A kitchen or bar sink shall be considered as meeting the requirements for
drinking water facilities for employees. Water coolers and bubblers may be considered as satisfying the
requirement for drinking water when approved by the Authority Having Jurisdiction.
c. Laundry Trays: Multiple dwelling units or boarding houses without public laundry rooms shall not
require laundry trays.
d. Service Sinks: Service sinks may be omitted when the Authority Having Jurisdiction determines that
they are not necessary for proper cleaning of the facility.
7.21.6 Fixture Requirements for Special Occupancies

a. Additional fixtures may be required when unusual environmental conditions or special activities are
encountered.
b. In food preparation areas of commercial food establishments, fixture requirements may be dictated by
the health and/or sanitary codes. Fixtures, fixture compartments and appliances used forrinsing or sanitizing
equipment or utensils, processing or preparing food for sale or serving,shall be installed in accordance with
Section 9.1.1 to ensure the required protection from backflow and flooding.
c. Types of occupancy not shown in Tables 7.21.1 shall be considered individually by the Authority
Having Jurisdiction.
7.21.7 Facilities in Mercantile and Business Occupancies Serving Customers

a. Requirements for customers and employees shall be permitted to be met with a single set of restrooms
accessible to both groups. The required number of fixtures shall be the greater of the required number for
employees or the required number for customers.
b. Fixtures for customer use shall be permitted to be met by providing a centrally located facility acces-
sible to several stores. The maximum distance of entry from any store to this facility shall not exceed 500
feet.
c. In stores with a floor area of 150 square feet or less, the requirement to provide facilities for employees
shall be permitted to be met by providing a centrally located facility accessible to several stores. The maxi-
mum distance of entry from any store to this facility shall not exceed 300 feet.
d. Drinking water facilities are not required for customers where normal occupancy is short term.
e. For establishments less than 1500 square feet in total floor area, one water closet and one lavatory in a
restroom with a lockable door shall be permitted to provide the requirements for serving the customers and
employees.

7.21.8 Food Service Establishments
a. Food service establishments with an occupant load of 101 or more customers shall be provided with
separate facilities for employees and customers. Customer and employee facilities may be combined for
customer loads of 100 or less.
b. Drinking water facilities are not required in restaurants or other food service establishments if drinking
water service is provided.
7.22 Water Treatment Systems

Water softeners, reverse osmosis water treatment units, and other drinking water treatment systems shall
meet the requirements of the appropriate standards listed in Table 3.1.3. Waste discharge from such equip-
ment shall enter the drainage system through an air gap.
7.23 Safety Features for Spas and Hot Tubs
7.23.1 Spas and Hot Tubs

Spas and hot tubs shall comply with the following sections of ANSI/NPSI-2 & 3 1992.
7.23.2 Entrapment Avoidance

There shall be nothing in the spa or hot tub that can cause the user to become entrapped underwater. Types
of entrapment can include, but not be limited to, rigid, non-giving protrusions, wedge-shaped openings, and any
arrangement of components that could pinch and entrap the user.
7.23.3 Outlets Per Pump

There shall be a minimum of two (2) suction outlets for each pump in the suction outlet system, separated by
at least 3 feet or located on two (2) different planes, such as one on the bottom and one on a vertical wall, or
one on each of two vertical walls. The suction outlets shall be piped so that water is drawn through the
outlets simultaneously by a common suction line to the pump. Blocking one suction outlet shall not create
excessive suction at other suction outlets.
7.23.4 Obstructions and EntrapmentA voidance

Where vacuum cleaning fittings are provided, they shall be located outside of the spa or hot tub and shall not
be accessible to the spa or hot tub user.
7.24 Emergency Equipment

Emergency showers and eyewash stations shall comply with ANSI Z358.llisted in Table 3.1.3.

'"
co
co
w
<: Table 7.21.1
~
' Minimum Number of Required Plumbing Fixtures - Page 1
!'?.
C/J
to
'" Bath or Other
No. Classification Use Description No. Of Persons Water Closets Lavatories Drinking
~ of Each Sex (Urinals) Water Shower
~ Group
"l:J Facilities
Male Female Male Female
~
:;;
OQ A-I I - 50 I 1 I 2 I per 1 service
(j
co
I Assembly Theatres and other buildings for the performing arts
and motion pictures usually with fixed scats 51 - 100 add 1 add 1 add a add a 1000 sink per
101 - 200 add I add 2 add 1 add I people floor
t 201 - 300 add I add 1 add 0 add I
~
.., ea. add'!. 300
a See Notes: 6, 9,12,16 add 1 add 2 add 1 add 2
ii:"
"'-
over 300
1-25 I I I 2 I per 200 I service

A-2 Dance halls, nightclubs and for similar purposes.
26 - 50 add I add I add I add I people sink per
floor
51 - 100 add I add 2 add I add 1
ca. add'!. 200
See Notes: 2,3,6,9,12,13,16 over 100 add I add 2 add 1 add 2
A-3 I-50 I I 1 I I per I service

Auditoriums without permanent seating, art
51 - 150 add I add I add 0 add I 1000 sink per
galleries, exhibition halls, museums, lecture halls,
151 - 300 add 0 add 1 add a add 0 people floor
libraries, restaurants other than nightclubs, food
courts. ea. add'!. 300
See Notes: 2,3,6,9,12,13,16 over 300 add I add 2 add I add 2
A-4 and 1 - 1000 1 I 1 I I I service

a) Places of worship and other religious services.
over 1000 add I add 1 add 1 add I add I sink
A-5 Churches without assembly halls.
See Notes: 6,9, 12, 16
b) Arenas, convention halls, outdoor assembly 1 - 100 2 2 I 2 1 per 1 service

including grandstands, bleachers, coliseums, 101 - 200 add 2 add 3 add I add 2 1000 sink per
201 - 400 add 2 add 5 add 0 add I people floor
stadiums, amusement park structures, fair and
carnival structures, passenger terminals. ea. add'!. 200
up to 2,600 add I add 2 add 2 add 2
ca. add'!. 300 add 1 add 2 add 2 add 2
See Notes: 2, 3, 6, 9,12,13,16 over 2,600
c) Recreational facilities: includes health spas, golf 1 - 40 1 2 1 2 1 per 75 I 1 service

courses, public swimming pools and similar uses. ea. add'!. 40 people shower per sink per
over 40 add I add 2 add I add 2 15 people 1100r
over 150
add I per
30
See Notes: 2, 3, 6, 9, 12, 16 people
...
00
.....
.....
QQ
~
Table 7.21.1
Minimum Number of Required Plumbing Fixtures - Page 2
No. Classification Use Description No. Of Persons Water Closets Lavatories Drinking Bath or Other
Group of Each Sex (U rinals) Shower
Water
Male Female Male Female Facilities
2 Business B 1 - 15 I 1 I 1 per 1000 I service

Buildings for the transaction of business, professional 1
serviccs, other services involving merchandise, office 16 - 40 add I add I add 0 add 2 people sink per
41 -75 add 1 add 1 add I add I floor
buildings, banks, light industrial and similar uses.
ca. add'!. 60 add I add 2 add I add 2
over 75
See Notes: 2,6, 7,12,15,16
3 Education 1-15 I I 1 1 I per 100 I service

E a) Educational facilities: Preschool, Day Care,
Kindergartcn 16 - 30 add I add I add I add I people sink per
31 - 45 add I add I add I add I floor
46 - 60 add I add 1 add 1 add 1
See Notes: 6,9, 16
61 -75 add 1 add I add I add I
76 - 90 add I add I add I add I
ca. add'!. 30 add I add I add 1 add 2
over 90
b) Elcmentary Grades I - 5 I - 25 I I I 2 I per 100 I service

26 - 50 add I add I add I add I pcople sink per
51 -75 add 1 add I add I add I floor
See Notes: 6,9, 16
76 - 100 add I add I add I add I
ea. add'!. 50
ovcr 100 add 1 add 1 add I add 2
'"
'"
'"
v.,
c) Secondary Grades 6 - 12 and higher education facilities 1-30 I 1 I 2 I per 100 1 service
~ 31 - 60 add I add I add I add I
people sink per
E!.. 61 - 90 add I add I add 1 add 1 floor
See Notes: 6,9, 16, 17 91 - 120 add I add I add 1 add I
~
'" ea. add 'I. 60
f} over 120 add I add 2 add I add 2
i$.
"1;J
'"
'"
"'" 4 Factory and F-1 and Structures in which occupants are cngaged in work 1-10 1 I I I I per 75 1 emergency 1 service
Industrial F-2 fabricating, assembly or proccssing of products or materials. II - 25 add 1 add I
~. add 0 add 1 peoplc shower per 10 sink per
\)
co 26 - 50 add I add I add 1 add I people when floor
k" 51 - 75 add I add I add 0 add 1 exposed to
I 76 - 100 add 1 add 1 skin
1 emerg.
add I add 2 Shower
~ contamination
1':; See Notes: 6,9, 12, 16
ea. add'!. 50 add 2 add 2 add 2 add 2 and eye
~ over 100 wash
ii)
"'-
'"
<:::>
<:::>
w
~
(3'
Table 7.21.1
'" Minimum Number of Required Plumbing Fixtures - Page 3
8..
SQ
'"
'" No. Classification Use Description No. Of Persons Water Closets Lavatories Bath or Other
2-
.., Group of Each Sex (U rinals) Drinking Shower
"-
'" Water
'"
'" Male Female Male Female Facilities
Q-
S.
(iq
(j
co
f} 6 Institutional I-I Six or more individuals in a supervised environment. 1 - 8 patients I I y, of required I per 100 I pcr 20 I service
I water closets people people sink per
::::0 Group homes. Aleohol and drug centers, convalescent ca. add'\" 8 add I add I
'" facilities, hospital wards. lloor
"'-
.., Sec Notcs: 16
over 8
'"
R"
"-
1-2 a) Buildings, with six or more individuals, used for I water closet per room I per room' I per room I service
medical, surgical, psychiatric, nursing or custodial care. sink per
floor
b) Hospital rooms: private or semi-private.
1-3 Buildings, with six or more persons under some restraint or 1 per 6 I service
I per cell or I per ecll or
security: inmates sink per
a) Detcntion centers (short term). I per 4 inmates I per 4 inmates lloor
See Noles: 14,16
I pcr 15 I service
1 per cell or I per cell or
b) Prisons, jails and reformatories (long term). inmates sink per
I per 8 inmates I per 8 inmates lloor
See Notes: 14, 16
7 Mercantile M a) Fixtures for customers in buildings occupied for 1-- 50 I 1 I I I per 1000 I service
display and sales purposes. Retail stores. service stations, 51 - ISO add I add I add 0 add I people sink per
shops, salesrooms, markets and shopping centers. 151 -300 add 0 add I add 0 add 0 lloor
ca. add'!. 300 add I add 2 add 1 add 2
See Notes: 2, 6, 7,12, IS, 16 over 300
Fixtures for employees in buildings for the transaction 1- 15 I I I I I pcr 1000 I service
of business, professional services, other services, 16-40 add I add I add 0 add 2 people sink per
involving merchandise, office buildings, banks, light 41-75 add I add 1 add I add I lloor
industrial and similar uses. ca. add'!. 60 add I add 2 add I add]
over 75
See Notes: 2, 6, 7,12,15,16
,...
00
UI
......
00
0\
Table 7.21.1
Minimum Number of Required Plumbing Fixtures - Page 4
No. Classification Use Description No. Of Persons Water Closets Lavatories Bath or Other
Group of Each Sex (Urinals) Drinking Shower
Water
Male Female Male Female Facilities
8 Residential R-I I water closet per unit I per unit I service

a) Hotels, motels. I per unit
sink per
floor
b) Dormitories and boarding houses. 1-20 2 2 I 2 I per 100 2 I service

ea. add'\, 20 add I add 2 add I add 2 or I per ea. add'\, sink per
floor 20 add I floor
I laundry
tray per
See Notes: 6,9, 10, 16 100
I kitchen
R-2 Multi-family dwellings. I water closet per unit I per unit I per unit sink per
unit
1 laundry
tray per
See Note: 10 100
R-3 One and two-family dwellings, 1 water closet per unit I per unit I per unit I kitchen
R-4 Detached one and two-family dwellings sink
I service
9 Storage S-I Structures for the storage of goods, warehouses, 1 water closel per unit I per unit 1 per unit sink per
'"
Q storehouses and freight depots. Moderate hazard. unit
Q
'"
S-2 Structures for the storage of goods, warehouses,
~ storehouses and freight depots. Low hazard.
'"
8... See Notes: 1,6
~
'"
1} 10 Utility and U Accessory buildings: Barns, carports, stables, sheds, None required
tS. miscellaneous greenhouses.
'"1J
~
~.
~
1}
:h
"
~
'"
"-
'"
a
a
w
<:
~
o.
'"
::!..
~
!::)
'"
f}
~
'<J
a- Notes forTable7.21.1:
~.
(j
co I. This table shall be used unless superseded by the Building Code. For handicap requirements see local, state or national codes. Additional
"'-
(t fixtures may be required where environmental conditions or special activities may be encountered.
~
~
2. Drinking fountains are not required in restaurants or other food service establishments if drinking water service is available. Drinking
'"'
!::) water is not required for customers where normal occupancy is short term. A kitchen or bar sinkmay be used for employee water drinking
;;;- facilities.
"'-
3. In food preparation areas, fixture requirements may be dictated by local Health Codes.
4. Whenever both sexes are present in approximately equal numbers, multiply the total census by 60% to determine the number of persons
for each sex to be provided for. This regulation only applies when specific information, which would otherwise affect the fixture count, is
not provided.
5. Not more than 50% ofthe required number of water closets may be urinals.
6. In buildings with multiple floors, accessibility to the fixtures shall not exceed one vertical story.
7. Fixtures for public use as required by this section may be met by providing a centrally located facility accessible to several stores. The
maximum distance from entry to any store to this facility shall not exceed 500 feet.
8. In stores with floor areas of ISO sq. ft. or less, the requirements to provide facilities for use by employees may be met by providing central
facilities located accessible to several stores. The maximum distance from entry to any store from this facility shall not exceed 300 feet.
9. Fixtures accessible only to private offices shalt not be counted to determine compliance with this section.
10. Multiple dwellings or boarding houses without public laundry rooms shall not require laundry trays.
II. (Reserved)
12. Requirements for employees and customers may be met with a single set of rest rooms. The required number of fixtures shall be the greater
of the required number of employees, or the required number of customers.
n. Food service establishments with an occupant load of 10] or more customers shall be provided with separate facilities for employees and
customers. Customer and employee facilities may be combined for customer loads of I00 or less.
I
14. Water closet and lavatory may be a combination fixture. All showers and lavatories shall have thermostatic control and timing devices.
IS. See Section 7.21.4 and Section 7.21.7 for toilet facilities for occupancies with a total floor area of I,500 square feet or less.
16. In determining the number of required fixtures for numbers of persons that fait in the "each additional (xx)" and "over (xx)" listings, the
requirement applies to fractions of the listed group.
17. Laboratories in higher education facilities shall have safety showers.
"'"'
00
-:t
Blank Page
188 2003 National Standard Pumhing Code-fllustrated

, Chapter8
Hangers and Supports

8.1 GENERAL
a. Hangers and anchors shall be securely attached to the building construction at sufficiently close intervals
to support the piping and its contents.
b. Fixtures, appliances and equipment shall be connected to support the weight ofthe device and any
additional probable loads that may impact on the device.
c. Fixtures shall be rigidly supported so that no strain is transmitted in the piping connections.
8.2 VERTICAL PIPING

a.Vertical pipe ofthe following materials shall be supported according to manufacturer's recommenda-
tions, but no less than the distances listed below:
1. Cast-iron soil pipe-at base and at each story height.
2. Steel threaded pipe-at every other story height.
3. Copper tube-at each story height but not more than 10-foot intervals.
4. Lead pipe-four-foot intervals.
5. Plastic pipe-see Section 8.7.
6. Flexible plastic tubing-each story height and at mid-story.
7. Stainless steel drainage pipe-at each story height.
8.3 HORIZONTAL PIPING

a. Horizontal pipe of the following materials shall be supported according to manufacturer's recommenda-
tions, but not less than the distances listed below:
1. Cast-iron soil pipe-minimum of one hanger per pipe length located within 18 inches of each joint (up to
1O-foot maximum pipe length), at changes in direction, and at branch connections. Where pipe is suspended by
non-rigid hangers more than 18 inches long, provide lateral support at 25-foot maximum spacing. Lateral
support shall consist of either 1) a sway brace or 2) either a change in direction or a branch connection that
provides the required lateral support.
2. Steel threaded pipe-3/4-inch size and smaller-I O-foot intervals. One-inch size and larger-12-foot
intervals.
3. Copper tube (1-1/4 inch size and smaller)-6-foot intervals.
4. Copper tube (1-1/2 inch size and larger)-10-foot intervals.
5. Lead pipe-on continuous metal or wood strips for its entire length.
6. Plastic pipe-see Section 8.7.
7. Flexible plastic tubing- 32 inches. .
8. Stainless steel drainage pipe-l 0 foot intervals, changes of direction and branch connections.

8.4 MATERIAL
a. Hangers, anchors, and supports shall be of metal or other material of sufficient strength to support the
piping and its contents.
b. Piers shall be of concrete, brick, or other masonry construction.
8.5 STRAIN AND STRESSES IN PIPE

Piping in the plumbing system shall be installed so as to prevent strains and stresses which will exceed the
structural strength of the pipe. Provision shall be made for expansion and contraction of the piping. (See
Sections 4.1.3 and 4.2.16.) See Figures 8.5-A through-C
PIPE HANGER
I OR SUPPORT
SUFFICIENT
LENGTH TO
ALLOW FOR
EXPANSION
E E
ANCHOR "\
'\GUIDES
\
TO ALLOW FR
LINEAR MOVEMENT j '\GUIDES
\
TO ALLOW FR
LINEAR MOVEMENT j / ANCHOR
PLAN VIEW
Figure 8.5 -A
AN EXPANSION LOOP IN A HOT WATER PIPE LINE
Bf.~~:f~.~~
GUIDES TO ALLOW FREE GUIDES TO ALLOW FREE ANCHOR
\ LINEAR MOVEMENT
l ----- \ LINEAR MOVEMENT
l I
0 C ~ C ~ 3
~ MECHANICAL EXPANSION JOINT

(SLIP JOINT TYPE)
Figure 8.5 - B
AN EXPANSION COMPENSATOR IN A HOT WATER PIPE LINE

GUIDES AND ANCHORS GUIDES AND ANCHORS
NOT SHOWN NOT SHOWN
CORRUGATED TUBING
WITH BRAIDED METAL JACKET
Figure 8.5 - C
A FLEXIBLE EXPANSION LOOP TO ABSORB THERMAL EXPANSION
8.6 BASE OF STACKS

Bases of cast-iron stacks shall be supported on concrete, brick laid in cement mortar, metal brackets attached
to the building construction, or by other methods approved by the Authority Having Jurisdiction. Other piping
material shall be so anchored as to support the stack at the base.
8.7 SUPPORT OF PLASTIC PIPE

Hangers and straps shall not compress, distort, cut or abrade the piping and shall allow free movement of the
pipe. Restrainingjoints and expansion joints shall be installed as required. Pipe shall be supported at intervals of
not more than four feet, at end of branches, and at a change of direction or elevation. Supports shall allow free
movement. Vertical piping shall be maintained in straight alignment. Trap arms in excess ofthree feet shall be
supported as close as possible to the trap. Installation shall be as per appropriate standards and manufacturer's
instructions.
8.8 UNDERGROUND INSTALLATION

See Section 2.6.

Blank Page

Chapter 9
Indirect Waste Piping and Special Wastes

9.1 INDIRECT WASTES
9.1.1 General
Drains from fixtures, fixture compartments, equipment, appliances, appurtenances, and other devices
requiring protection against contamination from backflow or flooding from the drainage system or other
source shall not be directly connected to any soil, waste, or vent pipe. Such drains shall discharge sepa-
rately through an air gap or, where permitted, an air break.
9.1.2 Air Gaps

The clear air gap between a drain outlet or indirect waste pipe and the flood level rim of an indirect waste
receptor or other point of disposal shall be not less than twice the diameter ofthe effective opening of the
drain served, but not less than one inch.
9.1.3 Air Breaks

Where air breaks are permitted, the waste pipe shall be permitted to terminate below the flood level rim
ofthe receptor but shall maintain an air space above the top ofthe receptor's trap seal. Such indirect
waste pipes shall be permitted to connect to the inlet side of the receptor's trap.
9.1.4 Where Indirect Wastes Are Required

Indirect wastes shall be provided for food-handling or food-storage equipment, medical or other sterile
equipment, clear-water wastes or discharges, and other drains as required herein.
9.1.5Food Handling Establishments

a. Fixtures and appliances used for the storage, processing, preparation, serving, dispensing, or sale of
food shall be drained indirectly. Examples of such fixtures include refrigerated cases, steam kettles, steam
tables, potato peelers, egg boilers, coffee urns and brewers, culinary sinks used for soaking or washing
food, ice machines, ice storage bins, drink dispensers, and similar equipment or appliances. A separate
indirect waste pipe shall be provided for each fixture drain and each shall discharge separately through an
air gap or air break into a trapped and vented receptor.
b. Where bar sinks, glass-washing sinks, or other counter sinks cannot be vented according to the
requirements of Chapter 12, they shall be permitted to each discharge separately to a trapped and vented
receptor through indirect waste pipes providing either an air break or air gap. See Figures 9.1.5 - A
through - C

INLET
CULINARY SINK
T
I
CULINARYSINK T I
I
I
I
L
i 1
"R'RE~OR I
]/
AIR GAP
I I OUTLET
LOCATE
THE AS ASPOSSIBLE
FIXTURE
AIRGAPFrT~~gSE
TO AIRGAPFITTING
A. MULTIPLE COMPARTMENT SINKS-

INDIRECT WASTE REQUIRED FOR
FOOD PREPARATIONSINKS
T
I
I
~ I
I
/ VENTE~ FLOORSINK
B. COMMERCIAL DISHWASHER ARRANGEMENT- AIR BREAK
AIR GAP IS REQUIRED

FOR ICE MAKER
C. ICEMAKING MACHINE
Figure 9.1.5 - A
INDIRCT WASTE PIPING IN A FOOD HANDLING AREA
SODA I
DISPENSER I
I
I
VENT--I
I
I
I
I
WASTE---
Figure 9.1.5 - B
INDIRECT WASTES FOR COUNTER SINKS AND COUNTER-MOUNTED EQUIPMENT

VENT
FOOD PREP OR
\
I
DISHWASHING
SINK
IT
~SOIL OR WASTE
I I
,/ STACK
I
I
FLOOR DRAIN \ I
NOTES:
1. If there is a stoppage in the soil or waste stack, the sewage will overflow from the floor drain
before it backs up into the food prep or dishwashing sink.
Figure 9.1.5 - C
PROTECTING A FOOD PREP OR
DISHW ASHING SINK FROM SEWAGE BACKUP
EXCEPTIONS:
(1) Indirect drains shall not be required for domestic kitchen sinks or domestic dishwashers.
(2) The rinsing and sanitizing compartments of three-compartment commercial sinks shall be drained
indirectly, in accordance with Section 9.1.1, but the pot washing compartment shall discharge to the
drainage system through a grease interceptor in accordance with Section 6.1.1.
(3) If a properly vented floor drain is installed immediately adjacent to a sink used for dishwashing, a
properly trapped and vented sink or sink compartment shall be permitted to connect directly to the drain-
age system, on the sewer side of the floor drain trap.
9.1.6 Walk-in Coolers and Freezers

a. If floor drains are located in walk-in coolers or walk-in freezers used for the storage of food or other
products for human consumption, they shall be indirectly connected to the sanitary drainage system.
b. Separate indirect waste pipes shall be provided for the floor drains from each cooler or freezer, and
each shall discharge separately through an air gap or air break into a trapped and vented receptor.
c. Traps shall be provided in the indirect waste pipe when required under Section 9.2.3.
d. Indirectly connected floor drains may be located in freezers or other spaces where freezing tempera-
tures are maintained, provided that traps are not required under Section 9.2.3. Otherwise, the floor ofthe
freezer shall be sloped to a floor drain located outside the storage compartment.
e. The above requirements do not apply to refrigerated food preparation areas or work rooms.
9.1.7Medical and Other Sterile Equipment

Stills, sterilizers, and other sterile equipment requiring drainage shall each discharge separately through an
air gap into a trapped and vented receptor.

9.1.8 Potable Clear-Water Wastes
Discharges of potable water from the water distribution system, water storage or pressure tanks, water
heaters, water pumps, water treatment equipment, boilers, relief valves, backflow prevention devices, and
other potable wa~ersources shall be indirect through an air gap.
EXCEPTION: An air break shall be permitted where the potable water supply to boilers, water-cooled
equipment, heating and air-conditioning systems, and similar cross-connections is protected by a backflow
prevention device in accordance with Section 10.5.
9.1.9 Drinking Fountains and WaterCoolers

Drinking fountains and water coolers shall be permitted to discharge indirectly through an air break or air
gap. Where such fixtures are connected to a dedicated drainage stack, the fixtures may connect directly
to the stack and the stack shall terminate with an air break or air gap.
9.1.10 Air Conditioning Equipment

Where condensate or other drainage from air conditioning or cooling equipment discharges to a drainage
system, it shall discharge indirectly to a trapped and vented receptor through an air break or air gap.
EXCEPTION: An air break shall not be permitted where the drain connects to a point in the air condition-
ing equipment that operates at a pressure below atmospheric.
See Figure 9.1.10
DIRECTION OF AIR FLOW
t.
/AIR CONDITIONING UNIT
CONDENSATE PAN (SHOWN UNDER NEGATIVE PRESSURE)
TRAP REQUIRED / AIR GAP SHOWN - AIR BREAK

IS ACCEPTABLE IF PRESSURE
OF CONDENSATE DRAINAGE
/ FROM APPLIANCE IS POSITIVE
~
Figure 9.1.10
DRAINING AIR CONDITIONING CONDENSATE
9.1.11 Swimming Pools

Drainage from swimmingpools or wading pools, includingpool drains, filter backwash, overflows, and
pool deck drains, shall discharge indirectly through an air gap to a trapped and vented receptor.
9.1.12 Relief Valve Discharge Piping

Discharge piping from relief valves and any associated indirect waste piping shall be in accordance with
Section 10.16.6.
9.2 INDIRECT WASTE PIPING
9.2.1 Materials and Installation

Indirect waste piping shall be of materials approved for sanitary drainage under Section 3.5.
9.2.2 Pipe Size

Indirect waste piping shall be not less than the nominal size of the drain outlet on the fixture or equipment
served.
9.2.3 Fixture Traps

Traps shall be provided at fixtures and equipment connections where the developed length of indirect
waste piping exceeds ten feet.
EXCEPTION: Drain lines used for clear-water wastes.
9.2.4 Provisions for Cleaning

Indirect waste piping shall be installed in a manner to permit ready access for flushing and cleaning.
Where necessary, cleanouts shall be provided in accordance with Section 5.4.
9.3 INDIRECT WASTE RECEPTORS
9.3.1 General
a. Receptors for indirect wastes shall be properly trapped and vented floor drains, floor sinks,
standpipes, open-hub drains, air gap fittings, or other approved fixtures.
b. Receptors shall be of such size, shape, and capacity as required to prevent splashing or flooding by
the discharge from any and all indirect waste pipes served by the receptor.
c. Plumbing fixtures that are used for domestic or culinary purposes shall not be used as receptors for
indirect wastes, except as follows:
EXCEPTIONS:
(1) In a dwelling unit, a kitchen sink trap, or food waste grinder, shall be permitted to receive the
discharge from a dishwasher.
(2) In a dwelling unit, a laundry sink, provided that an air gap is maintained for any potable clear-water
waste, shall be an acceptable receptor for:
a. Air conditioning condensate.
b. Automatic clothes washer.
c. Water treatment unit.
d. Water heater relief valve discharge.
(3) A service sink or mop basin shall be an acceptable receptor for air conditioning condensate and
any infrequent potable clear-water waste if the required air gap is provided for potable clear-water
wastes.
See Figures 7.15.2, 7.15.3, 7.15.4, 9.1.5-A, 9.1.5-B, and 9.1.10

9.3.2 Strainers or Baskets
Floor sinks and floor drains that handle other than clear-water wastes shall include a beehive strainer not
less than four inches in height or a readily removable metal basket to retain solids. See Figure 9.3.2
~~~'~-~D
(~,
11_1_11
I I
L_J
I-I
L_J
;;:~:'\ 00000000000
00000000000
1~
"II
jREMOVABLE BASKET
AIR BREAK 00000000000

WHERE PERMITTED
000000000 I
000000000
\LOPTIONAL FLATBOTTOMSTRAINER
RECEPTOR RECEPTOR
WITH WITH
DOMED BOTTOM REMOVABLE
STRAINER BASKET
NOTES:
1. Receptors may have a partially open top grate.
2. Domed bottom strainers help to reduce splashing.
3. In the receptor with a basket, the optional flat bottom strainer protects the drain line while the
basket is removed.
Figure 9.3.2
FLOOR SINKS WITH STRAINER OR BASKET
9.3.3 Prohibited Locations

Receptors for indirect wastes shall not be located in a toilet room or in any confined, concealed, inacces-
sible, or unventilated space.
EXCEPTION: Air conditioning condensate in dwellings shall be permitted to drain to a tub waste and
overflow or lavatory tailpiece in accordance with Section 9.4.3.c.5.
9.3.4 Standpipes
A standpipe, 2-inch minimum pipe size and extending not more than 48 inches nor less than 18 inches
above its trap, shall be permitted to serve as a receptor for a domestic clothes washer. In a dwelling, a
laundry sink shall be permitted to drain into the standpipe. See Figure 9.3.4

1~" OR 1).1"-
VENT 2"MIN.
STAND - 1BETWEEN 18" AND 48"
PIPE
STANDPIPE FOR STANDPIPE FOR

DOMESTIC CLOTHES WASHER FLOOR DRAIN
/STANDPIP/VENT
,.
LAUNDRY I
TRAY I
LAUNDRY TRAY AND
I CLOTHES WASHER DRAIN
I (SINGLE FAMILY DWELLINGS ONLY)
I
I
NOTES:
1. Standpipes shorter than 18" may cause splashing and overflow.
2. Standpipes taller than 48" may cause the trap to self-siphon. They may also retain waste
particles and create an odor problem.
Figure 9.3.4
STANDPIPE RECEPTORS
9.3.5 Open-hub Drains

A trapped and vented open-end drain pipe extending not less than 2 inches above the surrounding floor
shall be permitted to serve as a receptor for clear-water wastes.
9.3.6 Minimum Receptor Pipe Size

a. The minimum drain pipe size for an indirect waste receptor shall be at least one pipe size larger than
the indirect waste pipe that it serves.
EXCEPTION: A laundry sink receiving the discharge from an automatic clothes washer under Section
9.3.1.b.2.
b. Where a receptor receives indirect drainage from two or more fixtures, the cross-sectional area of the
receptor drain shall be not less than the aggregate cross-sectional area of all indirect waste pipes served
by the receptor. For the purposes of this requirement, 1-1/4" pipe = 1.2 in2,1-1/2"pipe = 1.8 in2,2" pipe
= 3.1 in2,2-1/2" pipe = 4.9in2,3"pipe=7.1 in2,4" pipe = 12.6in2, 5" pipe = 19.6in2,and6"pipe =
28.3 in2. See Figure 9.3.6

q"
DD~
L 3"MIN. J
NOTES:
1. The aggregate cross-sectional area of three 1-1/2" indirect waste pipes is 3 x 1.8 = 5.4 square
inches. A 2" outlet size is only 3.1 square inches. The minimum receptor outlet pipe size is 3"
with 7.1 square inches.
Figure 9.3.6
MINIMUM RECEPTOR OUTLET PIPE SIZE
9.3.7 Drainage Fixture Unit (DFU) Values

The drainage fixture unit values used to combine the loading of indirect waste receptors with other
fixtures shall be the sum of the DFU values for all fixtures that are indirectly drained into the receptor.
9.4 SPECIAL WASTES
9.4.1 Treatment of Corrosive Wastes

Corrosive liquids, spent acids, or other harmful chemicals that may damage a drain, sewer, soil or waste
pipe, create noxious or toxic fumes, or interfere with sewage treatment processes shall not be discharged
into the plumbing system without being thoroughly neutralized or treated by passing through a properly
constructed and approved neutralizing device. Such devices shall be provided automatically with a suffi-
cient supply of neutralizing medium, so as to make its contents non-injurious before discharge into the
drainage system. The nature of the corrosive or harmful waste and proposed method of its treatment shall
be submitted to and approved by the Authority Having Jurisdiction prior to installation. See Figures
9.4.1 and 1.2.55

SENSORWIRE
/ /SOLENOID VALVE
J() .0 --POTABLE WATER
~VACUUM BREAKER(APPROVEDTYPE)
~ASPIRATOR
VENT NEUTRALIZING
SOLUTION
FLOOR LINE
- OUTLET FLOW
TREATMENT
TANK
NOTES:
1. The automatic system can neutralize acids or caustic, depending on what neutralizing solution
is used. If the system had two chemical feeders, it could neutralize both acid and caustic
wastes.
Figure 9.4.1
AN AUTOMATIC WASTE TREATMENT NEUTRALIZING TANK
9.4.2 High Temperature Wastes

No waste at temperatures above 1400P shall be discharged directly into any part of a drainage system.
Such wastes shall be discharged to an indirect waste receptor and a means of cooling shall be provided
where necessary.
9.4.3 Air Conditioning Condensate

a. Indirect waste piping from air conditioning units shall be sized according to the condensate-generating
capacity of the units served. Branches from individual units shall be no smaller than the drain opening or
drain connection on the unit. Traps shall be provided at each air conditioning unit or cooling coil to main-
tain atmospheric pressure in the waste piping.
b. Condensate waste piping shall be sloped not less than 1/8" per foot. Drainage fittings shall be used in
sizes 1-1/4" and larger. Minimum pipe sizing shall be as follows:
3/4" pipe size through 3-ton cooling capacity
1" pipe size through 20-ton cooling capacity
2003 National Standard Pwnbing Code-Illustrated 201

1-1/4" pipe size through IOO-toncooling capacity
1-1/2" pipe size through 300-ton cooling capacity
2" size pipe through 600-ton cooling capacity
c. Discharge of air conditioning condensate shall not be pennitted to create a nuisance such as by flowing
across the ground or paved surfaces. Unless expressly prohibited by the Authority Having Jurisdiction,
the point of indirect discharge for air conditioning condensate shall be one of the following:
I. The building sanitary drainage system.
2. The building stonn drainage system.
3. A sump pump.
4. A subsurface absorption pit or trench.
5. Within dwellings, a tub waste and overflow or lavatory tailpiece within the same dwelling.
3/4"
MIN.
3 TONS =3/4" MIN.
3/4"
MIN.
6 TONS = 1" MIN.
3/4"
MIN.
9 TONS = 1" MIN.
--- TO POINT
OF DISPOSAL
NOTES:
1. The condensate drain traps on air conditioning (cooling) units must have sufficient trap seal
depth to offset the static pressure (positive or negative) at the condensate drain connection of
the unit. The traps are shown with a seal depth for a negative pressure
Figure 9.4.3 - A
SIZING INDIRECT WASTE PIPING FOR AIR CONDITIONING CONDENSATE

TO POINT OF
DISCHARGE
AIR
CONDITIONING
UNIT
AIR
;.- FULL PORT
CONDITIONING
UNIT
II CHECK
r---L SHUTOFF VALVE
VALVE
TO POINT
OF DISCHARGE
TO A RECEPTOR
TO A SUMP PUMP
-
~NSATE PIPING
AIR
BRANCH WYE FITTING
CONDITIONING
UNIT
I
I
I
I
I
I
,..a., THERMOSTAT
LI ACCESSIBLE
TO OCCUPANT
LAVATORY
BRANCH
TAILPIECE
OVERFLOW TAPPED
TO RECIEVE
CONDENSATE PIPING
EXAMPLES OF LAVATORY OR
BATHTUB CONDENSATE
CONNECTIONS
Figure 9.4.3 - B
DISCHARGING AIR CONDITIONING CONDENSATE

Blank Page
204 20G] National Standard Pumbing Code-Illustrated

Water Supply and Distribution
10.1 QUALITY OF WATER SUPPLY

Only potable water shall be supplied to plumbing fixtures used for drinking, bathing, culinary use or the processing
offood, medical or pharmaceutical products.
10.2 IDENTIFICATION OF POTABLE AND NON-POTABLE WATER

In buildings where dual water distribution systems are installed, one potable water and the other non-potable water,
each system shall be identified either by color marking or metal tags, or other appropriate methods such as may be
approved by the Authority Having Jurisdiction. Each outlet on the non-potable water line which may be used for
drinking or domestic purposes shall be posted: DANGER-UNSAFE WATER. See Figure 10.2
SERVICE AND BACKGROUND COLOR
Potable Water = GREEN

Non-Potable Water = YELLOW
Cold Water Supply = GREEN
Hot Water Supply = YELLOW
Hot Water Return = YELLOW
Sanitary Drain = GREEN
Plumbing Vent = GREEN
Waste = GREEN
Waste (corrosive) = YELLOW
Storm Drain = GREEN
Roof Drain = GREEN
Fire Protection = RED
NOTES:
1. Color coding of piping is based on ANSI A 13.1 - Scheme for the Identification of Piping Systems.
Figure 10.2
COLOR CODING FOR PIPING

10.3 WATER REQUIRED
10.3.1 Buildings
Plumbing fixtures shall be provided with a potable supply of water in the amounts and at the pressures
specified in this Chapter.
10.4 PROTECTION OF POTABLE WATER SUPPLY
10.4.1 General
A potable water supply shall be designed, installed and maintained to prevent contamination from non-potable
liquids, solids or gases by cross connections.
10.4.2 Interconnections
Interconnections between two or more public water supplies shall be permitted only with the approval of the
AuthorityHavingJurisdiction.
10.4.3 Cross Connection Control

Potable water supplies shall be protected in accordance with the cross connection control program of the
Authority Having Jurisdiction and the provisions of this Code. Cross connection control shall be provided at
individual outlets, and where required, by containment of the premises. Each potential cross connection within
the premises shall be protected. Where containment is required, the potable water supply shall be protected
by a backflow protection device installed immediately downstream of the meter or between the service
shutoff valve and the first outlet or branch connection. See Figures 10.4.3 - A and - B
---VACUUM
BREAKER
--- RUBBER HOSE

/ MOP SINK
/' / FINISHED FLOOR
URINAL BATHTUB MOP SINK
NOTES:
1. Individual outlet protection is required by this Code. It protects the potable water distribution piping
from being contaminated by a cross connection within the property.
Figure 10.4.3 - A
CROSS CONNECTION CONTROL BY INDIVIDUAL OUTLET PROTECTION

PUBLIC WATER
MAIN 11
BACKFLOW PREVENTION DEVICE
TO CONTAIN BACKFLOWS TO
WITHINTHE PROPERTY 3
BUILDING
SERVED-I
rs:I ,
BUILDING WATER SERVICEJ
BUILDING SERVICE
SHUTOFF VALVE J
NOTES:
1. Cross connection control by containment protects the public water supply from being contaminated
by a cross connection within a customer's property.
Figure 10.4.3 - B
CROSS CONNECTION CONTROL BY CONTAINMENT OF THE BUILDING
10.4.4 Private Supplies

a. Private potable water supplies (i.e., wells, cisterns, lakes, streams) shall require the same backflow
protection that is required for a public potable water supply.
b. Cross connection between a private potable water supply and a public potable water supply shall not be
made unless specifically approved by the Authority Having Jurisdiction.
Comment: Interconnections between private water supplies and public water supplies are generally
prohibited because private supplies are usually not monitored continuously for water quality.
10.4.5 Toxic Materials

a. Piping conveying potable water shall be constructed of non-toxic material.
b. The interior surface of a potable water tank shall not be lined, painted, or repaired with any material
which will affect either the taste, odor, color or potability ofthe water supply when the tank is placed in or
returned to service.
Comment: The toxicity rating of a piping material can befound in the material standard listed in Table
3.1.3. The piping materials listed in Table 3.4 are non-toxic and are suitablefor conveying potable
water.
10.4.6 Reserved
10.4.7 Reserved
10.4.8 Used Materials
2003 National Standard Pumbing Code-J//ustrated 207

Materials which have been used for any purpose other than conveying potable water shall not be used for
conveying potable water.
10.4.9 Water As a Heat-Transfer Fluid

Potable water may be used as a heat-transfer fluid provided the system design is approved by the Authority
10.5 BACKFLOW PREVENTION
10.5.1 Plumbing Fixtures, Appliances, Water Supply Outlets

The water supply shall be protected from back-siphonage by a fixed air gap between the potable water outlet
and the overflow level of the fixture or receptor.
10.5.2 Requirements for Air Gaps

a. How Measured: The air gap shall be measured vertically from the lowest end of a potable water outlet
to the flood rim or line of the fixture or receptor into which it discharges.
b. Minimum Size (distance): The minimum required air gap shall be twice the effective opening of a potable
water outlet unless the outlet is a distance less than 3 times the effective opening away from a wall or similar
vertical surface in which case the minimum required air gap shall be 3 times the effective opening of the
outlet. In no case shall the minimum required air gap be less than that shown in Table 10.5.2. See Figure
10.5.2
TABLE 10.5.2
MINIMUM AIR GAPS FOR PLUMBING FIXTURES
Minimum Air Gap
Fixture When not Affected When Affected
By Near Wall' By Near Wall'

(Inches) (Inches)
Lavatories with effective opening not -r 1-1/2
greater than 1/2 inch diameter
Sink, laundry trays, goose-neck bath faucets and other fixtures 1-1/2 2-1/4
with effective openings not greater than 3/4" diameter ~
Over rim bath fillers and other fixtures with 2 .)
effective openings not greater than 1 inch diameter

1-1/2
Drinking water fountains-single orifice not greater than 7/16
(0.437) in. diameter or multiple orifices having total area of
0.150 square inches (area of circle 7/16 in. diameter)
2X 3X
Effective openings greater than one inch
diameter of diameter of
effective opening effective opening
I. Side walls, ribs or similar obstructions do not affect air gaps when spaced from inside edge of the spout opening a distance greater than
three times the diameter ofthe effective opening for a single wall, or a distance greater than four times the diameter of the effective opening for
two intersecting walls.
2. Vertical walls, ribs, or similar obstructions extending from the water surface to or above the horizontal plane of the spout opening require
a greater air gap when spaced closer to the nearest inside edge of the spout opening than specified in Note I. above. The effect of three or more
such vertical walls or ribs has not been determined. In such cases, the air gap shall be measured from the top of the wall.

,- AIR GAP - 2 TIMESTHE DIAMETER"d"
~ BUT NOT LESS THAN 1"

I I ORIFICE OPENING- DIAMETER"d"
TYPICAL LAVATORY FAUCET - AIR GAP
AIR GAP -
2 TIMES THE
DIAMETER"d"
BUT NOT
LESS THAN 2"L

d l f--
TYPICAL TUB FILLER - AIR GAP

NOTES:
1. Diameter "d" is the opening on the faucet aerator, tub spout, or outlet pipe
Figure 10.5.2
MINIMUM REQUIRED AIR GAPS
10.5.3 Required Backflow Prevention Devices

The following requirements shall apply:
A. Low Hazard - Back-Siphonage - Intermittent Pressure
I. Air gap
2. Atmospheric vacuum breaker
3. Hose connection vacuum breaker
4. Any backflow protection device approved for protection against continuous pressure
back-siphonage.
B. Low Hazard - Back-Siphonage - Continuous Pressure
1. Pressure-type vacuum breaker
2. Spill-proof vacuum breaker (SVB)
3. Double check with intermediate atmospheric vent
4. Double check valve assembly
5. Reduced pressure backflow pre venter assemblies
C. Low Hazard - Back-Pressure
1. Double check with intermediate atmospheric vent
2. Double check valve assembly
3. Reduced pressure backflow preventer assemblies
D. High Hazard - Back-Siphonage
1. Pressure-type vacuum breaker
E. High Hazard - Back-Pressure

10.5.4 Approval of Devices
Before any device for the prevention of backflow or back-siphonage is installed, it shall have first been
certified by a recognized testing laboratory acceptable to the Authority Having Jurisdiction.
10.5.5 Installation of BackflowPreventers

a. Devices of All Types: All backflow prevention devices shall be accessible. Backflow prevention
devices having atmospheric vents shall not be installed in pits, vaults, or similar potentially submerged loca-
tions. Vacuum breakers and other devices with vents to atmosphere shall not be located within fume hoods.
b. Atmospheric Vacuum Breakers: Pipe applied atmospheric vacuum breakers shall be installed with the
critical level at least six inches above the flood level rim or highest point of discharge of the fixture being
served. Approved deck-mounted and pipe-applied vacuum breakers and vacuum breakers within equipment,
machinery and fixtures where the critical level is a specified distance above the source of contanination shall
be installed in accordance with manufacturer's instructions with the critical level not less than one inch above
the flood level rim. Such devices shall be installed on the discharge side of the last control valve to the fixture
and no shut-off valve or faucet shall be installed downstream of the vacuum breaker. Vacuum breakers on
urinals shall be installed with the critical level six inches above the flood level rim. See Figures 10.5.5 - A
through - F. Also Figures 10.5.10 - A through - C
ON-OFF SWITCH-
NOTES:
1. If the critical level (C-L) is not marked on the vacuum breaker body, the bottom of the valve is
considered to be the C-L reference.
2. Atmospheric vacuum breakers are not rated for periods of more than 12 hours of continuous water
pressure.
Figure 10.5.5 - A
THE POT ABLE WATER SUPPLY TO A COMMERCIAL FOOD WASTE GRINDER
PROTECTED BY AN ATMOSPHERIC VACUUM BREAKER
ATMOSP
VACUUMHB~R~~KER I
'",M'RG' ~
POTENTION~~L~SE~
/~"
'I
NOTES:
1. Atmospheric vacuum breakers are not rated for periods of more than 12 hours of continuous water
pressure.
Figure 10.5.5 - B
THE POTABLE WATER SUPPLY TO A SERVICE SINK

ATMOSPHERIC
:\ VACUUM BREAKER
SUBMERGED HOSE
NOTES:
1. Atmospheric vacuum breakers are not rated for periods of more than 12 hours under continuous
water pressure.
Figure 10.5.5 C -
THE POT ABLE WATER SUPPLY TO A LAB SINK
~ ATMOSPHERIC VACUUM BREAKER
6"MIN'L
C-L
~ SUCTION DEVICE
t
WASTE
DISCHARGE
Ir
WATER
SUPPLY
NOTES:
water pressure.
Figure 10.5.5 D -
THE POTABLE WATER SUPPLY TO AN ASPIRATING DEVICE

FLUSHOMETER --
VALVE
NOTES:
water pressure.
Figure 10.5.5 E -
THE POTABLE WATER SUPPLY TO A WATER CLOSET OR URINAL
ANTI-SIPHON BALLCOCK WITH

CRITICAL LEVEL
1" ABOVE
OVERFLOW
U rr-::==1
h X
INTERGRAL VACUUM BREAKER
II f""'" JJS:EFILL TUBE

OVERFLOW TUBE
flr:1 ~Fl:' 1.-

-,~ c-
t:ILL TUB~
/ FLAPPER
>~ FLUSH VALVE
FLUSH TANK ASSEMBLY

WATERSUPPLY---
Figure 10.5.5 F -
THE POTABLE WATER SUPPLY TO A WATER CLOSET GRAVITY FLUSH TANK
PROTECTED BY AN ANTI-SIPHON BALLCOCK WITH INTEGRAL VACUUM BREAKER

c. Pressure Type Vacuum Breakers: Pressure type vacuum breakers shall be installed with the critical
level at a height of at least 12 inches above the flood level rim for ASSE 1020 devices and with the critical
level at least six inches above the flood level rim or highest point of discharge of the fixture being served for
ASSE 1056 devices. Deck-mounted and pipe-applied pressure type (ASSE 1056) vacuum breakers within
equipment, machinery and fixtures where the critical level is a specified distance above the source of con-
tamination shall be installed in accordance with manufacturer's instructions with the critical level not less than
one inch above the flood level rim. See Figure 10.5.5 - G. Also Figures 10.5.10 - D and - E
SEE NOTES 1 & 4

I SIPHON /
PRESSURE V
ASSE 1020 A~6~UM BREAKE"'-
",CJ--
=. I:- SEE
NOTE 2
TO OTHER FIXTURES
REQUIRING POTABLE WATER
t SEE NOTE 3
PROCESS EQUIPMENT
~ POTABLEWATERSUPPLY
NOTES:
1. ASSE 1020anti-siphon pressurevacuum breakers can be located where subjected to continuous
pressure.
2. The critical level (C-L) of the vacuum breaker must be at least 12" higher than the highest down-
stream piping.
3. Shutoffvalves are permitteddownstreamfrom pressurevacuum breakers.
4. ASSE 1020 pressure vacuum breakersshould not be located where water spillage from the atmo-
spheric vent will cause damage or create a nuisance. If necessary, use ASSE 1056 spill-resistant
vacuumbreakers.
Figure 10.5.5 - G
THE POTABLE WATER SUPPLY TO INDUSTRIAL PROCESS EQUIPMENT
PROTECTED BY AN ANTI-SIPHON PRESSURE VACUUM BREAKER

d. Double Check Valves and Reduced Pressure Principle Valves: Such devices shall be installed at not less
than 12 inches above the floor with the maximum of 60 inches above floor. See Figures 10.5.5 - Hand - I.
Also 10.5.10 - F
1- DOUBLE CHECK VALVE ASSEMBLY I

1r
OPTIONAL
POTABLE
WYE STRAINER
m
---
~
Ii! ;(/)(
WATER --,l r---ll~-./ 01 10m0" " III" " JIto l---
SUPPLY
\ ut.'- '-LT
\
\"'/\ /~
'
I
I RESILIENT SEATED I
/ TO LOW HAZARD - BACKPRESSURE
APPLICATIONS
GATE VALVES
TEST PORTS -~
SEE NOTE 1
1
r FLOOR OR WORKING SURFACE
Notes:
1. Double check valve assemblies or reduced pressure backflowpreventorassemblies are requiredfor
back pressure application,
2. Double check valve assemblies must be installed between 12" and 60" above the floor or other
working surface to provide sufficient access for periodic testing and maintenance.
3. Double check valve assemblies subject to back-siphonage require an intermediate vacuum breaker
and a relief vent.
4. Double check valve assemblies with an intermediate vacuum breaker and relief vent must not be
located in a pit or other area subject to flooding. The relief vent will create a cross-connection if
submerged.
Figure 10.5.5 - H
THE POTABLE WATER SUPPLY TO A LOW HAZARD - BACKPRESSURE APPLICATION
PROTECTED BY A DOUBLE CHECK VALVE ASSEMBLY
214 2003 National Standard Pumhing Code-lllustrated

TO A HIGH HAZARD BACK-PRESSURE BACKFlOW APPLICATION SUCH AS
COOLING TOWER MAKEUP, BOilER WATER MAKEUP, OR HYDRONIC PIPING
SYSTEM MAKEUP WHERE CHEMICAL TREATMENT IS PROVIDED AND THE
WATER IN THE PIPING SYSTEM IS NOT POTABLE.
REDUCED PRESSURE ZONE

BACK FLOW PREVENTOR ASSEMBLY
POTABLE
WATER t--
SUPPLY
RESILIENT SEATED
'- AIR GAP O~ I

AIR GAP FITTING
SHUTOFF VALVES
LJ
r FLOOR OR WORKING SURFACE
NOTES:
1. Reduced pressure zone principle backflow prevention devices must be installed between 12" and
60" above the floor or other working surface to provide sufficient access for periodic testing and
maintenance.
2. Double check valve assemblies are not permitted for high hazard backpressure applications.
3. RPZ devices must not be installed in pits or other area subject to flooding. The relief vent will create
a cross-connection if submerged.
4. If occasional spillage from the relief vent will cause damage or be a nuisance, the vent must be
equipped with an air gap fitting and indirectly drained to an acceptable point of disposal.
Figure 10.5.5 - I
THE POTABLE WATER SUPPLY TO A HIGH HAZARD - BACKPRESSURE APPLICATION
PROTECTED BY A REDUCED PRESSURE BACKFLOW PREVENTER ASSEMBLY
e. Spill-proof Vacuum Breakers: Approved deck mounted and pipe-applied spill-proof vacuum breakers
within equipment, machinery and fixtures where the critical level is a specified distance above the source of
contamination shall be installed in accordance with manufacturer's instructions with the critical level not less
than one inch above the flood level rim.
10.5.6 Maintenance and Testing of Backflow Prevention Devices

a. Devices installed in a building potable water supply distribution system for protection against backflow
shall be maintained in good working condition by the person or persons responsible for the maintenance of the
system.

b. Devices which are designed to be field tested shall be tested prior to final inspection of the initial
installation and once each year thereafter, using field test procedures conforming to ANSI! ASSE 5010 Series
Professional Qualifications Standards or equivalent.
NOTE: Testable devices are those backflow prevention devices having test cocks and include, but are not
limited, to the following:
1. Pressure vacuum breakers
2. Spill-proof vacuum breakers
3. Double check valve assemblies
4. Double check detector assemblies
6. Reduced pressure detector assemblies
c. Where tests indicate that the device is not functioning properly, it shall be serviced or repaired in
accordance with the manufacturer's instructions and be retested.
d. Testing and repair of devices shall be performed by certified individuals approved by an agency
acceptable to the Authority Having Jurisdiction. Certification for testing shall be in accordance with ANSI!
ASSE 5000 or equivalent. Certification for repair shall be in accordance with ANSI! ASSE 5030 or equivalent.
Certification shall include not less than 32 hours of combined classroom and practice training and successful
completion of a written and practical examination.
e. Copies of test reports for the initial installation shall be sent to the Authority Having Jurisdiction and the
water supplier. Copies of annual test reports shall be sent to the water supplier.
f. Where a continuous water supply is critical and cannot be interrupted for the periodic testing of a
backflow prevention device, multiple backflow prevention devices or other means of maintaining a continuous
supply shall be provided that does not create a potential cross connection.
10.5.7 Tanks and Vats-Below Rim Supply

a. Where a potable water outlet terminates below the rim of a tank or vat and the tank, or vat has an
overflow of a diameter not less than given in Table 10.8.3, the overflow pipe shall be provided with an air gap
as close to the tank as possible.
b. The potable water outlet to the tank or vat shall terminate a distance not less than 1-112times the height
to which water can rise in the tank above the top of the overflow. This level shall be established at the
maximum flow rate of the supply to the tank or vat and with all outlets closed except the air-gapped overflow
outlet.
c. The distance from the outlet to the high water level shall be measured from the critical point of the
potable water supply outlet.
See Figure 10.5.7. Also Sections 10.8.3, 10.8.4, 10.8.5, and 10.8.6

--
- - --
It?
GAP ~
SEE NOTE 3 POTABLE WATER
- - -
TANK OUTL7
-
t
TANK DRAIN VALVE
t POTABLE WATER TO
BOOSTER PUMP OR
GRAVITY SUPPLY TO
WATER DISTRIBUTION
SYSTEM
NOTES:
1. The covers of potable water tanks or vats must have screened vent pipes with internal areas not less
than that of the outlet pipe.
2. The size of the overflow pipe must comply with Table 10.8.3, based on the maximum makeup water
flow rate.
3. The air gap at the tank overflow discharge must be 2 X the inside diameter of the overflow pipe.
4. The maximum overflow water level must be established based on the size of the overflow pipe and
the maximum available makeupwater flow. Calculated required static head or rise above the invert
of the overflow should be confirmed by operationaltests under actual full flow conditions with the
tank outlet(s) closed.
5. The required air gap at the water inlet to the tank or vat must be at least 1-1/2 times the rise in
water level above the invertofthe overflow outlet undermaximumoverflow conditions, measuredfrom
the invertofthe tank overflow.
Figure 10.5.7
A POTABLE WATER TANK OR VAT WITH ITS INLET BELOW THE OVERFLOW RIM
10.5.8 Connections to Carbonated Beverage Dispensers

The water supply to a carbonated beverage dispenser shall be protected against backflow with an integral
backflow preventer confonning to ASSE 1022 or an air gap. Carbonated beverage dispensers and carbon-
ated beverage dispensing systems without an integral backflow preventer conforming to ASSE 1022 or an air
gap shall have the water supply protected with a double check valve with atmospheric vent conforming to
ASSE 1022.
10.5.9 Protection from Fire Systems

a. Potable water supplies to fire protection systems, including but not limited to standpipes and automatic
sprinkler systems, shall be protected from back-pressure and back-siphonage by one of the following testable
devices:
1. double check valve assembly,
2. double check detector assembly,
3. reduced pressure backflow preventer assembly, or
4. reduced pressure detector assembly
EXCEPTIONS:
2003 National Standard Pumbing Code-l/Iustrated 217

Where fire protection systems supplied from a potable water system include a fire department (Siamese)
connection which is located less than 1700 feet from a non-potable water source that could be used by the
fire department as a secondary water supply, the potable water supply shall be protected by one of the
following:
(1) Reduced pressure backflow preventer assembly
(2) Reduced pressure detector assembly
b.Non-potable water sources include fire department vehicles carrying water of questionable quality or
water that is treated with antifreeze, corrosion inhibitors, or extinguishing agents.
c. Where antifreeze, corrosion inhibitors, or other chemicals are added to a fire protection system supplied
from a potable water supply, the potable water system shall be protected by one of the following:
1. Reduced pressure backflow preventer assembly
2. Reduced pressure detector assembly
d. Whenever a backflow device is installed in the potable water supply to a fire protection system, the
hydraulic design of the system shall account for the pressure drop through the backflow device.
e. If such devices are retrofitted for an existing fire protection system, the hydraulics of the sprinkler
system design shall be checked to verify that there will be sufficient water pressure available for satisfactory
operation ofthe fire sprinklers.
10.5.10 Protection from Lawn Sprinklers and Irrigation Systems

a. Potable water supplies to systems having no pumps or connections for pumping equipment, and no
chemical injection or provisions for chemical injection, shall be protected from backflow by one of the follow-
ing devices:
2. Pressure vacuum breaker (PVB)
b. Where sprinkler and irrigation systems have pumps, connections for pumping equipment, auxiliary air
tanks or are otherwise capable of creating back-pressure, the potable water supply shall be protected by the
following type of device if the backflow device is located upstream from the source of back-pressure.
c. Where systems have a backflow device installed downstream from a potable water supply pump or a
potable water supply pump connection, the device shall be one of the following:
2. Pressure vacuum breaker (PVB)
d. Where systems include a chemical injector or any provisions for chemical injection, the potable water
supply shall be protected by the following:
1. Reduced pressure backflow pre venter assembly

10.5.11 Domestic Water Heat Exchangers
a. Heat exchangers used for heat transfer, heat recovery, or solar heating shall protect the potable water
system from being contaminated by the heat transfer medium, in accordance with either subparagraph b or c
below.
b. Single-wall heat exchangers shall be permitted if they satisfy all of the following requirements:
1. The heat transfer medium is either potable water or contains only substances which
are recognized as safe by the U.S. Food and Drug Administration.
2. The pressure of the heat transfer medium is maintained less than the normal minimum
operating pressure of the potable water system.
EXCEPTION: Steam complying with subparagraph b.l.
3. The equipment is permanently labeled to indicate that only additives recognized as
safe by the FDA shall be used in the heat transfer medium.
c. Double-wall heat exchangers shall separate the potable water from the heat transfer medium by
providing a space between the two walls which is vented to the atmosphere.
10.5.12 Hose Connections

a. Water heater and boiler drain valves that are provided with hose connection threads and which are
intended only for tank or vessel draining shall not be required to be equipped with a backflow preventer.
b. This section shall not apply to water supply valves intended for connection to clothes washing machines
where backflow prevention is otherwise provided or is integral with the machine.
10.5.13 Protection for Special Equipment

The water supply for any equipment or device that creates a cross-connection with the potable water supply
shall be protected against backflow as required in Section 10.5. Such equipment and devices includes, but is
not limited to, chemical dispensers, portable cleaning equipment, sewer and drain cleaning equipment, and
dental pump equipment.
a. Chemical Dispensers
Where chemical dispensers connect to the water distribution system, the water supply system shall be pro-
tected against backflow in accordance with Section 10.5, which allows for an air gap, atmospheric or pres-
sure type (PYB or SYB), or a reduced pressure principle assembly.
b. Portable Cleaning Equipment
Where the portable cleaning equipment connects to the water distribution system, the water supply system
shall be protected against backflow in accordance with Section 10.5, which allows for an air gap, atmospheric
or pressure type (PYB or SYB), or a reduced pressure principle assembly.
c. Dental Pump Equipment
Where dental pumping equipment connects to the water distribution system, the water supply system shall be
protected against backflow in accordance with Section 10.5, which allows for an air gap, atmospheric or
pressure type (PYB or SYB), or a reduced pressure principle assembly.
10.6 WATER SERVICE
10.6.1 Separationof Water Serviceand Building Sewer

The water service pipe and building drain or building sewer shall not have less than one foot horizontal
distance between the piping. See Figures 10.6.1 - A and - B
2()()3 National Standard Pumbing Code-Illustrated 219

BUILDING DRAIN OR BUILDING SEWER
,
7/
SUFFICIENT DEPTH FOR FREEZE PROTECTION
l _rWATER SERVICE PIPE/
NOTES:
1. Improvements inthe integrityof undergrounddrainage system pipejoints has permitted the separa-
tion from potable water piping to be reduced to 12 inches.
Figure 10.6.1 - A
THE MINIMUM DISTANCE BETWEEN AN UNDERGROUND WATER SERVICE
AND A BUILDING DRAIN OR BUILDING SEWER
\
\
WATER SERVICE
// 12" \ WATER SERVICE
L BUILDING DRAIN L BUILDING DRAIN

OR SEWER OR SEWER
WATER SERVICE OVER (PREFERRED)
WATER SERVICE UNDER ( PERMITTED)
NOTES:
1. The minimum clearance is 12 inches.
2. Where possible, the water service should cross over the building drain or building sewer.
3. If necessary, the water service can cross under the building drain or building sewer.
4. The 12" minimum separation prevents direct contact between the pipe lines, even with considerable
settlement.
Figure 10.6.1 - B
CROSSING A WATER SERVICE OVER (OR UNDER)
A BUILDING DRAIN OR BUILDING SEWER
220 2003 National Standard Pwnbing Code-Illustrated

10.6.2 Water Service Near Sources of Pollution
Potable water service piping shall not be located in, under or above cesspools, septic tanks, septic tank
drainage fields or drainage pits. A separation often feet shall be maintained from such systems. When a
water line crosses a sewer, a minimum clearance of 12 inches shall be maintained. See Figure 10.6.2
CESSPOOL, SEPTIC TANK,

SEPTIC TANK DRAINAGE FIELD,
AND DRAINAGE PIT
/"
~
/ 10 FEET \
MINIMUM
CLEARANCE \
-
/
f 6--
MINIMUM \
POTABLE WATER SERVICE PIPING
\
)
~ .......
/
/
Figure 10.6.2
MINIMUM CLEARANCE BETWEEN A WATER SERVICE PIPE
AND SOURCES OF CONT AMINA nON
10.6.3 Stop-and- Waste Valves Prohibited

Combination stop-and-waste valves or cocks shall not be installed underground in water service piping.
Comment: Open waste outlets on underground water service shutoff valves wouldpermit ground water
to contaminate the potable water supply.
10.6.4 Water Service Pipe Sleeves

Pipe sleeves shall be provided where water service pipes penetrate foundation walls or floor slabs to protect
against corrosion ofthe pipe and allow clearance for expansion, contraction and settlement. The sleeve shall
form a watertight bond with the wall or floor slab. The annular space between the pipe and the sleeve shall
be resiliently sealed watertight. Where water service piping is plastic, the wall sleeve shall be not less than
five feet long extended outside beyond the wall. See Figure 10.6.4

FLOOR SLAB ~,
\L PLASTIC WATER
SERVICE PIPE
WATER SERVICE PIPE SLEEVE
FLOOR SLAB ~
XIIr SEE NOTE 1
METALLIC WATER SERVICE PIPE
NOTES
1. The pipe sleeve must be sealed watertight to the wall or floor slab.
2. A 1/2" minimum annular space around the water pipe, between the pipe and the sleeve, is required
and must be sealed watertight.
3. Sleeves for plastic water service pipe mustextend outside beyond foundation walls to undisturbed
earth and be at least 5 feet long.
Figure 10.6.4
WATER SERVICE PIPE SLEEVES FOR METALLIC AND PLASTIC PIPING
10.6.5 Water Service Sizing

The water service pipe shall be of sufficient size to furnish water to the building in the quantities and at the
pressures required elsewhere in this Code. The pipe size shall not be less than 3/4 inch nominal.
10.7 WATER PUMPING AND STORAGE EQUIPMENT
10.7.1 Pumps and Other Appliances

Water pumps, filters, softeners, tanks and other appliances and devices used to handle or treat potable water
shall be protected against contamination as per Section 10.5.
222 20G] National Standard Pumbing Code-Illustrated

10.7.2 Prohibited Location ofPotable Supply Tanks
Potable water gravity tanks or manholes of potable water pressure tanks shall not be located directly under
any soil or waste piping.
10.8 WATER PRESSURE BOOSTER SYSTEMS
10.8.1 Water Pressure Booster Systems Required

a. When the water pressure in the public water main or individual water supply system is insufficient to
supply the potable peak demand flow to plumbing fixtures and other water needs freely and continuously with
the minimum pressure and quantities specified in Section 10.14.3, or elsewhere in this Code, and in accor-
dance with good practice, the rate of supply shall be supplemented by one of the following methods:
1. An elevated water tank.
2. A hydro-pneumatic pressure booster system.
3. A water pressure booster pump.
10.8.2 Reserved
10.8.3 Overflows for Water Supply Tanks

Gravity or suction water supply tanks shall be provided with an overflow having a diameter not less than that
shown in Table 10.8.3. The overflow outlet shall discharge above and within not less than 6 inches of a roof
or roof drain, floor or floor drain, or over an open water-supplied fixture. The overflow outlet shall be covered
by a corrosion-resistant screen of not less than 16 x 20 mesh to the inch and by 1/4 inch hardware cloth, or it
shall terminate in a horizontally installed 45 angle-seat check valve. Drainage from overflow pipes shall be
directed so as not to freeze on roof walkways. See Figure 10.5.7
TABLE 10.8.3
SIZES! OF OVERFLOW PIPES FOR WATER SUPPLY TANKS
Maximum Capacity Diameter of Maximum Capacity Diameter
of Water Supply Line Overflow Pipe of Water Supply Line Overflow Pipe
to Tank (Inches ID) to Tank (Inches ID)
0-13 gpm 1-1/2 356-640 gpm 5
14-55 gpm 2 641-1040 gpm 6
56-100 gpm 2- 1/2 over 1040 gpm 8
101-165 gpm 3
166-355gpm 4
] Computed by the method ofNBS Mono. 31, for vertical pipes flowing not greater than 1/2 full at terminal velocity. (1/3 full for 1-1/2 in.
pipe).
10.8.4 Covers
All water supply tanks shall be covered to keep out unauthorized persons, dirt, and vermin. The covers of
gravity tanks shall be vented with a return bend vent pipe having an area not less than the area of the down
feed riser pipe and the vent shall be screened with corrosion resistant screen having not less than 14 and not
more than 20 openings per linear inch. See Figure 10.5.7
10.8.5 Potable Water Inlet Control and Location

Potable water inlets to gravity tanks shall be controlled by a ball cock or other automatic supply valve so
installed as to prevent the tank from overflowing. The inlet shall be terminated so as to provide an accepted
air gap but in no case less than 4 inches above the overflow. See Figure 10.5.7

10.8.6 TankDrain Pipes
Eachtank shallbe providedat its lowestpointwith a valvedpipeto permitemptyingthe tank. SeeFigure
10.5.7
10.8.7 Low Pressure Cut-Off Required on BoosterPumps

Booster pumps shall be protected by a low pressure cut-off switch to shut-off the pump( s) if the suction
pressure drops to an unsafe value.
10.8.8 Pressure Tanks-Vacuum Relief

All water pressure tanks shall be provided with a vacuum relief valve at the top of the tank which will operate
up to a maximum water pressure of 200 psi and to maximum water temperatures of 200F. The minimum size
of such vacuum relief valves shall be 1/2 inch.
10.8.9 Pressure Tanks-Pressure Relief

All water pressure tanks shall be provided with approved pressure relief valves set at a pressure not in excess
of the tank working pressure.
10.9 FLUSHING AND DISINFECTING POTABLE WATER SYSTEMS
10.9.1 Flushing
The water service piping and distribution piping to all fixtures and outlets shall be flushed until the water runs
clear and free of debris or particles. Faucet aerators or screens shall be removed during flushing operations.
10.9.2 Disinfecting
a. Where required by the Authority Having Jurisdiction, the water service piping and the hot and cold
water distribution piping in new or renovated potable water systems shall be disinfected after flushing and
prior to use. The procedure used shall be as follows or an approved equivalent:
1. All water outlets shall be posted to warn against use during disinfecting operations.
2. Disinfecting shall be performed by persons experienced in such work.
3. The water supply to the piping system or parts thereof being disinfected shall be valved-off from the
normal water source to prevent the introduction of disinfecting agents into a public water supply or portions of
a system that are not being disinfected.
4. The piping shall be disinfected with a water-chlorine solution. During the injection of the disinfecting
agent into the piping, each outlet shall be fully opened several times until a concentration of not less than 50
parts per million chlorine is present at every outlet. The solution shall be allowed to stand in the piping for at
least 24 hours.
5. An acceptable alternate to the 50 ppm/24-hour procedure described in Section 10.9.2.d shall be to
maintain a level of not less than 200 parts per million chlorine for not less than three hours. If this alternate
procedure is used, the heavily concentrated chlorine shall not be allowed to stand in the piping system for
more than 6 hours. Also, special procedures shall be used to dispose of the heavily concentrated chlorine in an
environmentally acceptable and approved manner.
6. At the end of the required retention time, the residual level of chlorine at every outlet shall be not less
than five parts per million. If the residual is less than five parts per million, the disinfecting procedure shall be
repeated until the required minimum chlorine residual is obtained at every outlet.
7. After the required residual chlorine level is obtained at every outlet, the system shall be flushed to
remove the disinfecting agent. Flushing shall continue until the chlorine level at every outlet is reduced to that
of the incoming water supply.

8. Any faucet aerators or screens that were removed under Section 10.9.1 shall be replaced.
9. A certification of performance and laboratory test report showing the absence of coliform organisms
shall be submitted to the Authority Having Jurisdiction upon satisfactory completion of the disinfecting opera-
tions.
10.10 WATER SUPPLY SYSTEM MATERIALS

See Section 3.4.3.
10.11 ALLOWANCE FOR CHARACTER OF SOIL AND WATER

When selecting the material and size for water service supply pipe, tube, or fittings, due consideration shall be
given to the action of the water on the interior of the pipe and of the soil, fill or other material on the exterior ofthe
pipe. (Appendix B gives recommendations concerning allowances to be made in sizing water piping because ofthe
properties of the water.)
Comment: The chemical composition of the service water should be considered when selecting the water
service pipe material. Refer to Appendix Section B.2.3. The aggressive nature of the soil orfill material
around the water service pipe should be evaluated when considering if additional corrosion protection is
needfor the exterior surfaces of the pipe.
10.12 WATER SUPPLY CONTROL VALVES
10.12.1 Curb Valve
On the water service from the street main to the building, an approved gate valve or ground key stopcock or
ball valve shall be installed near the curbline between the property line and the curb. This valve or stopcock
shall be provided with an approved curb valve box and shall not be under a driveway. See Figure 1.2.82
10.12.2 BuildingValve
The building water service shall be provided with a readily accessible gate valve with bleed or other full-way
valve with bleed located inside the building near the point where the water service enters. When the building
water service enters a crawl space, the building valve shall be readily accessible. Where there are two or
more water services serving one building, a check valve shall be installed on each service in addition to the
above valves. See Figure 1.2.82
10.12.3 WaterSupplyTankValve
A shutoff valve shall be provided at the outlet of any tank serving as a water supply source, either by gravity
or pressure. See Figure 10.5.7
10.12.4 Valves in Dwelling Units

a. Except as defined in 10.12.4.b, c and d, individual fixture shutoff or stop valves shall be provided for
water closets, lavatories, kitchen sinks, laundry trays, bar sinks, bidets, clothes washing machines, sill cocks,
wall hydrants, appliances and equipment connected to the water supply system. Valves for fixtures, appli-
ances and equipment shall be accessible without having to move the appliance or equipment.
EXCEPTION: Valves for ice makers
b. Shutoff valves shall be provided for each powder room or bathroom group unless all fixtures within the
room or group have individual fixture shutoff or stop valves.
c. In a single dwelling unit, two bathrooms or powder rooms installed back-to-back or one directly above the
other may be considered as a single group and shall be permitted to have one set of shutoff valves. If two

such rooms are not piped as a single group, separate shutoff valves shall be provided for each room or group.
d. In multi-dwelling units, one or more shutoff valves shall be provided in each dwelling unit so that the
water supply to any plumbing fixture or group of fixtures in that dwelling unit can be shut off without stopping
the water supply to fixtures in other dwelling units. These valves shall be accessible in the dwelling unit that
they control.
LAV - LAVATORY
~:Fr
j,fJ~~ DISHWASHER I
WC - WATER CLOSET 1
8 - REQUIRED
(~ J /1
I
I EFRIGERATOR
-
SHUTOFF VALVE
I
i i __l ~ITHICEMAKER
" we
b'l! '
I
L I '~WLAV
II cS
w-- - -LC:J
WC
:J
LAV '
O ~SHUTOFF VA~~~ROUP(S) j 88 I' / -
-
(
TUB
\
'-
j' ~EENOTE~
OR BATHRO
1=
==
I
=t'-,
! OFF VALVES
~ " "I
~~~TpOWDERROOM
(1
LYI ~'I~
lr';! ' - - SEE NOTE4
r
0 AV
I
0 "I, I ,
JLj)
) I
L.'::=::'J
.
,TUB II ,I
I
I, /
'R
I HEATER
J~
WC \ L I~
I \ I
I
~:~~OFF VALVE
I ~-I 1/
~
:
'il I WATER
V BUILDING VALVE
CLOTHES
F=,
I I ( )1, .
:lLL
HEATEr'"
,j
. WITHBLEED"
, ,
,
I
, L
I WASHER
SILLCOCK
WALL 0\
HYDRAN
il'n! /' WATERS=:!!!!}
NOTES
1. The building shutoff valve must be a full-way type with a bleed to drain the piping within the building.
2. The water heatershutoff valve must notbe a globevalve.
3. Additional shutoff valves can be provided to isolatethe water heater and branches of the water
distribution piping.
4. Shutoffvalves for powder rooms and bathroomgroups are not required if all fixtures within the group
have individual shutoff valves. One set of shutoff valves can servetwo bathroomgroups ifthey are
piped as one group of fixtures without separate branch pipes for each group.
5. Water closets and lavatories usually have individual supply stop valves where the fixture supply tube
connects to the fixture branch supply pipe.
6. Where manifold-typeparallelwater distribution systems are used,the individual fixture shutoff valves
are located on the manifold.
Figure 10.12.4 -A
REQUIRED WATER SHUTOFF VALVES IN SINGLE DWELLING UNITS

KITCHEN SINK
WC
LLf I
LAV
TUB
-- INDIVIDUAL
DWELLING
UNIT
KITCHEN SINK
WC
UJ lAV
TUB
-- INDIVIDUAL
DWELLING
UNIT
WC - WATER CLOSET
LAV - lAVATORY
~ - REQUIRED
SHUTOFF VALVE
NOTES
1. Riser shutoff valves are requiredwhere risersserve dwelling units on two or more floors.
2. Shutting off a fixture in one dwelling unit must not stop the water supply to a fixture in another
dwelling unit.
3. Main shutoff valves are not mandatoryfor each dwelling unit if all fixtures within the unit have a
means of shutoff.
4. Shutoff valves for powder rooms and bathroomgroups are not mandatory if all fixtures within the
group have individual shutoff valves. One set of shutoffvalves can servetwo bathroomgroups within
the same dwelling unit if they are piped as one group of fixtures without separate branch pipes for
eachgroup.
5. Water closets and lavatories usually have individual supply stop valves where the fixture supply tube
connects to the fixture branch supply pipe.
6. All shutoff valves for the fixtures in each dwelling unit must be accessible within the dwelling unit
that they serve.
Figure 10.12.4 - B
REQUIRED WATER SHUTOFF VALVES IN MULTI-DWELLING UNITS
10.12.5 Riser Valves

Shutoffvalves(s) shall be provided for isolating each water supply riser serving fixtures on two or more
floors.
EXCEPTION: Risers within individual dwelling units. See Figure 1.2.49
2003 National Standard Pumbing Code-II/ustrated 227

10.12.6 Individual Fixture Valves
In a building used or intended to be used for other than dwelling purposes, the water distribution pipe to each
fixture or other piece of equipment shall be provided with a valve or fixture stop to shut offthe water to the
fixture or to the room in which it is located. These valves shall be accessible. Sill cocks and wall hydrants
shall be separately controlled by a valve inside the building.
Comment: In buildings or portions thereof that are usedfor other than dwelling purposes, eachfIXture
or equipment connection must have an individual shutoffmeans. Shutoff valves in such systems cannot
shutoff a group offIXtures that do not have individual shutoff means. The guest rooms in hotels and
motels are considered to be dwelling units.
10.12.7 Water Heating Equipment Valve

A shutoff valve shall be provided in the cold water supply to each water heater. If a shutoff valve is also
provided in the hot water supply from the heater, it shall not isolate any safety devices from the heater or
storage tank. Shutoff valves for water heaters shall be the gate, ball, plug, or butterfly type. See Figure
10.12.7
t HOT ~COLD
In ~n COLD WATER
OPTIONAL HOT WATER
SHUTOFF VALVE ~ ' ~ L.?II SHUTOFF VALVE
I-I
n ~ RELIEF VALVE
II
II
DIP TUBE II
II
II
II ~ RELIEFVALVEDISCHARGEPIPE
II /' TO APPROVEDPOINTOF DISCHARGE
DRAIN VALVE - U
NOTES:
1. The cold water shutoffvalve permitsthe water heater to be serviced or replaced, but requires that
the hot water distribution piping be drained.
2. The optional hot water sh utoff valve permits the water heater to be serviced or replaced without
draining the hot water distribution piping.
3. The water heater relief valve must not be isolated from the water heater tank by any shutoff valves.
4. Water heater shutoff valves must be the full-flowtype. Globe valves are not permitted.
Figure 10.12.7
WATER HEATER SHUTOFF VALVE(S)
10.12.8 Meter Valve

A gate valve or other full-way valve shall be installed in the line on the discharge side of each water meter.
The valve shall not be less in size than the building water service pipe.
228 2003 National Standard Pumbing Code-lIIustrated

r METER FRAME & COVER
~ SIDEWALK
1
;; WATER METER
;. METERVAULT
.~
.
4
J
NOTE 2
BRICKS OR OTHER
~ ~.
:~~: POROUS BASE
"';J~
JI~
; 0(/ <?: "".~>iY~~
c:'(
,f'-----
CORPORATION COCK~
\ WATER SERVICE
I "
C(
ADAPTER FITTING
~ (3/4" MINIMUM SIZE) (NOTE3) "'-WATER SERVICE
0-
~ PUBLIC WATER MAIN
TO BUILDING
NOTES:
1. The stop valve on the inlet side of the water meter is normally provided by the water service utility. It
can be the curb valve required by Section 10.12.1.
2. The distinction between small and largewater services is dictated by the Authority Having Jurisdic-
tion. For small water services, the shutoff valve on the outlet side of the water meter can be the
building valve required by Section 10.12.2. See Figure 10.12.8- B for largerwater services.
3. Adapter fittings are requiredwhere the pipe materialfor the water service to the building is different
from the pipe material provided by the water utility.
Figure 10.12.8 - A
METER SHUTOFF VALVES IN A SMALL WATER SERVICE

r METER VAULT
.,
FOP!IONA~ BY~ASS.
VALVE. 4 ".,
..
, "'~
.< ~'
.
J'--- J'---
WATER SUPPLY FROM
..'
PUBLIC WATER MAIN
. c'
L OUTLET SHUTOFF VALVE ..
"
'. .
A, , 4, ". .
'. < . '.
,'~
," ", <.: .
NOTES:
1, The shutoff valve on the inlet side of the water meter is normally provided by the water utility.
2. The bypass valve is optional. It can be used to provide continuous water service while the meter is
being repaired or replaced.
3. The bypass valve and shutoff valve on the meter outlet permit the meter to be repaired or replaced
without interrupting the water service to the facility.
Figure 10.12.8 - B
METER SHUTOFF VALVES IN A LARGE WATER SERVICE
10.12.9 Valve Accessibility

Water supply control valves shall be placed so as to be accessible for service and maintenance.
Comment: Access to water supply shutojJvalves can require the use of tools iO-removeaccess panels or
doors.
10.13 Flexible Water Connectors

Flexible water connectors exposed to continuous pressure shall conform to ASME A 112.18.6listed in Table
3.1.3. Access shall be provided to all flexible water connectors.
10.14 MINIMUM REQUIREMENTS FOR WATER DISTRIBUTION

SYSTEMS
10.14.1 Maximum Velocity (See Appendix B.6)

Water distribution piping within buildings shall be sized for a maximum velocity of8 feet per second at the
design flow rate unless the pipe manufacturer's sizing recommendations call for the maximum velocity to be
less than 8 feet per second.

10.14.2 Sizeoflndividual FixtureSupplyBranches
a. Individual fixture supply branch pipe sizes shall be based on the minimum available flowing water
pressure at the point of connection to the water distribution system, any elevation difference between that
connection and the fixture, and the allowable pressure loss in the fixture supply branch. The minimum fixture
supply branch pipe sizes shall be as indicated in Table 10.14.2A. For design purposes, the required pressure
with flow at each fixture inlet shall be 15 psig minimum for all fixtures, except 25 psig for blowout water
closets and blowout urinals. The following water flow rates shall be used for the purpose of sizing individual
fixture supply branch pipes:
5.0 gpm for hose bibbs and wall hydrants;
4.0 gpm for bath faucets and clothes washers;
0.75 gpm for drinking fountains and water coolers;
2.5 gpm for sink faucets;
2.5 gpm for showers;
1.5 gpm for lavatory faucets;
3.0 gpm for gravity and flushometer tank-type water closets;
12.0 gpm for flushometer valve urinals;
20.0 gpm for flushometer valve water closets
b. Fixture supply branches shall extend from the distribution system to within 30 inches of the point of
connection to the fixture and be within the same area and physical space as the point of connection to the
fixture. Supply tubes (or risers), if required, shall be not less than the size recommended by the manufacturer
of the fixture, faucet or appliance.
10.14.3 SizingWaterDistributionPiping
a. The supply demand in gallons per minute in the building hot and cold water distribution system shall be
determined on the basis ofthe load in terms of water supply fixture units (WSFU) as shown in Table
1O.14.2A and the relationship between the load in WSFU and the supply demand in gallons per minute (gpm)
as shown in Table 10.14.2B. For fixtures having both hot water and cold water connections, the separate hot
water and cold water loads shall be taken as 75% ofthe listed fixture unit value.
b. Main risers and branches ofthe water distribution system shall be sized based on the minimum available
water pressure at the source, any elevation differences between the source and the fixtures, pressure losses
in the distribution system, and the pressure (with flow) required at each connection of the fixture supply
branches.
10.14.4 Inadequate Water Pressure

Whenever water pressure from the street main or other sources of supply is insufficient to provide flow
pressures at fixture outlets as required under Section 10.14.3, a booster pump and pressure tank or other
approved means shall be installed on the building water supply system.

TABLE IO.14.2A
WATER SUPPLY FIXTURE UNITS (WSFU) AND MINIMUM FIXTURE BRANCH
PIPE SIZES
HEAVY-USE ASSEMBLY
TYPE OF FIXTURES OTHER THAN DWELLING UNITS
SERVING 3 OR MORE DWELLING UNITS
INDIVIDUAL DWELLING UNITS
MINIMUM BRANCH PIPE SIZE
BATHROOM ,m .m.... 1.6 GPiF '''''fI!lii C'7 ,,,," fiJi"""Wi
GRAVITY-TANK WATER CLOSETS i
Half-bath or Powder Room 3.5 2.5
I Bathroom Group 5.0 3.5
I '/, Bathrooms 6.0

2 Bathrooms 7.0
2 '/, Bathrooms 8.0

3 Bathrooms 9.0
Each Additional '/, Bath 0.5
Each Additional Bathroom Group 1.0

.,.
BATHROOM GROUPS HAVING 1.6 GPF
L,,,,'iiii/i, ""c,/",/!
PRESSt'RFi.2J'AK
Half-bath or Powder Room
WAJ'Ji.,K'CI """'",.,'"
3.5
(If,"!ig'i'
"ii"
2.5
II- ie;''1

I '/, Bathrooms 6.0
2 Bathrooms 7.0
2 '/2 Bathrooms 8.0
3 Bathrooms 9.0
Each Additional '/2 Bath 0.5
BkJ'HRO<}M GROUPSl'IAYING ;5 Cf'iF 1:'%1'f,{fi'fi .1"2"JjI
'WI/"
PRESSURE-TANK WATER CLOSETS ".Ji " II
Halt:bath or Powder Room 4.0 3.0
I '/2 Bathrooms 8.0
2 Bathrooms 10.0
2 '/2 Bathrooms 11.0
3 Bathrooms 12.0
BATH GROUP (1.6 GPF FIushometer Valve) 6.0 4.0
BATH GROUP (3.5 GPF Flushometer Valve) 8.0 6.0
KITCHEN GROUP (Sink and Dishwasher) 2.0 1.5
LAUNDRY GROUP (Sink and Clothes Washer) 5.0 3.0
------
TABLE lO.14.2A (Continued)
WATER SUPPLY FIXTURE UNITS (WSFU) AND MINIMUM FIXTURE BRANCH
PIPE SIZES
HEA VY-USE ASSEMBLY

MINIMUM BRANCH PIPE SIZE
u,. f;;;;ft2if5J;J; iii". ii,;, Tfir. iii,i

....
ceIl iT;;
Bathtub or Combination Bath/Shower 1/2" 4.0 3.5
Bidet 1/2" 1.0 0.5
Clothes Washer, Domestic 1/2" 4.0 2.5 4.0
Dishwasher, Domestic 1/2" 1.5 1.0 1.5
Drinking Fountain or Watercooler 3/8" iT; T;T; 0.5 0.75
Hose Bibb 1/2" 2.5 2.5 2.5
Hose Bibb, Each Additional 1/2" 1.0 1.0 1.0
Kitchen Sink, Domestic 1/2" 1.5 1.0 1.5
Laundry Sink 1/2" 2.0 1.0 2.0
Lavatory 3/8" 1.0 0.5 1.0 1.0
Service Sink or Mop Basin 1/2" 3.0
Shower 1/2" 2.0 2.0 2.0
Shower, Continuous Use 1/2" 5.0
Urinal, 1.0 GPF 3/4" iiii 4.0 5.0
Urinal, Greater Than 1.0 GPF 3/4" 5.0 6.0
Water Closet, 1.6 GPF Gravity Tank 1/2" 2.5 2.5 2.5 4.0
Water Closet, 1.6 GPF Flushometer Tank 1/2" 2.5 2.5 2.5 3.5
Water Closet, 1.6 GPF Flushometer Valve I 5.0 5.0 5.0 8.0
Water Closet, 3.5 GPF Gravity Tank 1/2" 3.0 3.0 5.5 7.0
Water Closet, 3.5 GPF Flushometer Valve I 7.0 7.0 8.0 10.0
Whirlpool Bath or Combination Bath/Shower 1/2" 4.0 4.0
NOTES: .
I. A Bathroom Group, for the purposes of this Table, consists of not more than one water closet, up to two lavatories, and either one bathtub,
one bath/shower combination, or one shower stall. Other fixtures within the bathing facility shall be counted separately to determine the total
I
water supply fixture unit load.
2. A Half-Bath or Powder Room, for the purposes of this Table, consists of one water closet and one lavatory.
3. For unlisted fixtures, refer to a listed fixture having a similar flow and frequency of use.
4. The listed fixture unit values for Bathroom Groups and Individual Fixtures represent their load on the cold water service. The separate cold
water and hot water fixture unit values for fixtures having both cold and hot water connections shall each be taken as 3/4 of the listed total value
for the individual fixture..
5. When WSFU values are added to determine the demand on the water distribution system or portions thereof, round the sum to the nearest
whole number before referring to Table 10.14.2B for the corresponding gallons per minute (gpm) flow. WSFU values of 0.5 or more should be
rounded up to the next higher whole number (9.5 = 10 WSFU). Values of 0.4 or less should be rounded down to the next lower whole number (9.4
= 9 WSFU).
6. The listed minimum supply branch pipe sizes for individual fixtures are the nominal (1.0.) pipe size in inches.
7. "Other Than Dwelling Units" applies to business, commercial, industrial, and assembly occupancies other than those defined under "Heavy-
Use Assembly." Included are the public and common areas in hotels, motels, and multi-dwelling buildings.
8. "Heavy-Use Assembly" applies to toilet facilities in occupancies which place heavy, but intermittent, time-based demands on the water
supply system, such as' schools, auditoriums, stadiums, race courses, transportation terminals, theaters, and similar occupancies where queuing is
likely to occur during periods of peak use.
9. For fixtures or supply connections likely to impose continuous flow demands, determine their required flow in gallons per minute (gpm) and
add it separately to the demand (in gpm) for the distribution system or portion thereof.

TABLE 10.14.2B
T ABLE FOR CONVERTING DEMAND IN WSFU TO GPMl
GPM GPM GPM GPM

WSFU Flush Tanks2 Flush Valves3 WSFU Flush Tanks2 Flush Valves3
3 3 120 49 74
4 4 140 53 78
5 4.5 22 160 57 83
6 5 23 180 61 87
7 6 24 200 65 91
8 7 25 225 70 95
9 7.5 26 250 75 100
10 8 27 300 85 110
11 8.5 28 400 105 125
12 9 29 500 125 140
13 10 29.5 750 170 175
14 10.5 30 1000 210 210
15 11 31 1250 240 240
16 12 32 1500 270 270
17 12.5 33 1750 300 300
18 13 33.5 2000 325 325
19 13.5 34 2500 380 380
20 14 35 3000 435 435
25 17 38 4000 525 525
30 20 41 5000 600 600
40 25 47 6000 650 650
50 29 51 7000 700 700
60 33 55 8000 730 730
80 39 62 9000 760 760
100 44 68 10,000 790 790
NOTES:
1. This table converts water supply demands in water supply fixture units (WSFU) to required water flow in gallons per minute (GPM)
for the purpose of pipe sizing.
2. This column applies to portions of piping systems where the water closets are the flush tank type (gravity or pressure) or there are no
water closets, and to hot water piping.
3. This column applies to portions of piping systems where the water closets are the flush valve type.

10.14.5 Variable Street Pressures
Where street water main pressures fluctuate, the building water distribution system shall be designed for the
minimum pressure available.
10.14.6 Excessive Pressures
a. Approved pressure reducing valves complying with ANSI/ ASSE 1003 shall be provided if required to
limit the water supply pressure at any fixture appliance, appurtenance, or outlet to not more than 80 psi under
no-flow conditions.
b. The requirement of Section I 0.14.6.a above shall not prohibit supply pressures higher than 80 psi to
water pressure booster systems under Section 10.14.4 or in high pressure distribution systems, provided that
the pressure at the fixtures served is subsequently reduced to 80 psi maximum. Where operating water
pressures exceed 80 psi, the working pressure rating of materials and equipment shall be suitable for the
maximum pressure that may be encountered, including temporary increases or surges.
Where pressure reducing valves are installed and the downstream piping is not rated for the maximum
upstream pressure, a pressure relief valve shall be installed downstream from the pressure reducing valve.
The relief valve shall be set not higher than the working pressure rating ofthe downstream piping and sized
for not less than the flow capacity of the pressure reducing valve. Relief valves shall discharge in accordance
with Sections 10.16.6a, b, c, and d.
SUPPLY PRESSURE TO FIXTURES
REDUCED TO 80 P.S.I. MAX.
BUILDING VALVE
(Section 10.12.2)
~ PRESSURE RELIEF VALVE

(IF REQUIRED)
"- PRESSURE
REDUCING VALVE TO APPROVED
(Section 10.14.6) POINT OF
DISCHARGE
SUPPLY PRESSURE
GREATER THAN 80 psi
NOTES:
1. Strainers are recommended for pressure reducing valves. They can be integral with the PRV or
separately line-mounted.
2. A pressure relief valve is required forthe reduced-pressure downstream piping ifthe rated working
pressure of the downstream piping is not adequate for the maximum upstream pressure.
3. A means of measuring the reduced downstream pressure is required. This can be by the installa-
tion of a permanent pressure gauge, by the installation of a test connection for a portable gauge, or
by reading the pressure at a downstream hose-end faucet or hose bibb with a test gauge.
Figure 10.14.6 - A
INST ALLA nON OF A WATER PRESSURE REDUCING VALVE
WHERE THE WATER SUPPLY PRESSURE EXCEEDS 80 PSIG

~
/'
21 ST FLOOR
"' "'\ B 20 TH FLOOR

/ HOT WATER \ - 19THFLOOR
- / \
~
18 TH FLOOR
~cw--r RECIRCULATION
- +-w-HW---r-
\
/
/
/'
\. -
B 17 TH FLOOR
16 TH FLOOR
~
'-
'-_/ /' 15TH FLOOR
A 14 TH FLOOR
INSERT B \. - 13 TH FLOOR
~
12TH FLOOR
/'
"' "'\ SEE
/'A 11TH FLOOR
NOTE6 ----
/ PRY \ \. - 10 TH FLOOR
-~WT
~
9 TH FLOOR
- ~HW+
\ PRY /
/'
A 8 TH FLOOR
'-'-- //
\. - 7 TH FLOOR
~
/'....... 6 TH FLOOR
DOMESTIC WATER INSERT A
A
BOOSTER PUMP \r =--:-~:-l
\. -
5 TH FLOOR
4 TH FLOOR
WATER I
SUPPLY~
L J EXPANSION
HOT WATER --- TANK
CIRCULATOR --D t HOT WATER

HEATER
NOTES:
1. Example: A pressure booster pump is required to deliver domestic water to the 21st Floor.
2. The 1st ,2nd, and 3rd Floors are supplied with street pressure and a separate hot water heater.
3. The water supply pressure on the 4th through 15th Floors will exceed 80 psig.
4. Usually up to three floors can be zoned with one set of pressure reducing valves.
5. The pressure in the hot water recirculation line is the same as in the adjacent hot water supply
riser.
6. The diagram shows only the hot water riser recirculated. If hot water was recirculated from the
individual floors, pressure booster pumps would be requiredto pumpthe recirculated water from
each reduced pressurezone back into the higher pressure return riser (downcomer).
Figure 10.14.6 - B
ONE POSSIBLE ARRANGEMENT OF PRESSURE REDUCING VALVES
IN A HIGH-RISE BUILDING
10.14.7 Water Hammer

a. Approved water hammer arresters, complying with ANSI/ASSE 1010, shall be installed on water
distribution piping in which quick closing valves are installed.
EXCEPTION: Single lever faucets, domestic clothes washers, and domestic dishwashers.
b. Water hammer arresters shall be placed as close as possible to the quick acting valve, at the end oflong
piping runs, or near batteries of fixtures.
c. Arresters shall be accessible for replacement. See Figure 10.14.7

PRESSURIZED
AIR/GAS
CUSHION
"0" - RING SEAL

PISTON
DIAPHRAGM PISTON
TYPE TYPE
NOTES:
1. Water hammer arrestors should be sized and installed according to the manufacturer's instructions.
2. PDI Standard WH201 establishes PDI Sizes "A" through "F" with recommendations on the number
of fixture units served by each size. Most manufacturers rank their products to the PDI Sizes.
3. Water hammer arrestors can be installed vertically or horizontally. They should be installed on the
run of a tee fitting so that the unobstructed shock path is directly into the water hammer arrestor.
See Figure 1.2.3.
4. The number of elbows upstream from a water hammer arrestor should be minimized because they
create points of shock before the arrestor.
5. Water hammer arrestors must be accessible and have a means of shutoff to permit replacement if
necessary. The means of shutoff can be a shutoff valve for a group of fixtures.
Figure 10.14.7
WATER HAMMER ARRESTORS
10.15 HOT WATER
10.15.1 Hot Water Supply System

In residences and buildings intended for human occupancy, hot water shall be supplied to all plumbing
fixtures and equipment used for bathing, washing, culinary purposes, cleansing, laundry or building mainte-
nance. With the approval of the Authority Having Jurisdiction, tempered water supply systems may be
installed in lieu of hot and cold water systems in buildings other than dwelling units.
10.15.2 Temperature Maintenance Where Required

a. Heated water distribution systems in buildings where developed length of heated water piping from the
source of the heated water to the farthest fixture exceeds 100 feet shall maintain heated water temperature in
all supply piping to within 25 feet of any heated water outlet.
b. An approved electric heat tracing system shall be permitted to be used to satisfy the requirements of
Section 10.15.2a.
See Figure 10.15.2

'5'EET MAXIMUM 1
t
DISTANCE TO FARTHEST HOT WATER OUTLET EXCEEDS 100 FEET
1-
CW COLD --- I I
I
CHECK
VALVE-
(NOTE
2)
I --
- \
"---BALANCINGCOCKS
ED LINE
RECIRCULAT
'---
(NOTE 3)~
-
L AQUASTAT (NOTE 1)
HOT
z CIRCULATOR
WATER
SOURCE
TEMPERATUREMAl"' AINEDTO WITHINj

25 FEET OF ALL HOT WATEROUTLETS
NOTES:
1. The aquastat or time/temperature controller starts the circulator when the recirculated line cools.
The circulator stops when the line temperature rises.
2. The check valve in the cold water supply to the hot water source keeps recirculated hot water from
flowing into the cold water main due to pressure fluctuations in the distribution system.
3. If the recirculation piping has more than one branch, balancing cocks in each branch permit the
flows to be adjusted.
4. A means of measuringthe returntemperature should be provided.
Figure 10.15.2
HOT WATER TEMPERATURE MAINTAINENCE BY RECIRCULATION
10.15.3 Minimum Requirements for Hot Water Storage Tanks

a. Hot water storage tanks shall be adequate in size, when combined with the B.T.U.H. input of the water
heating equipment to provide the rise in temperature necessary.
b. Water heaters and storage tanks shall be sized to provide sufficient hot water to provide both daily
requirements and hourly peak loads of the occupants of the building.
c. Storage tanks shall be protected against excessive temperatures and pressure conditions as specified in
this Code. (See Sections 3.3.8 and 3.3.10)
10.15.4 Drainage of Hot Water Storage Tanks

Hot waterstoragetanksshallbe equippedwith a valvecapableof drainingthe tank completely.See Figure
10.12.7

10.15.5 Pressure Marking of Hot Water Storage Tanks
Hot water storage tanks shall be permanently marked in an accessible place with the maximum allowable
working pressure, in accordance with the applicable standard as listed in Table 3.1.3.
10.15.6 MixedWater Temperature Control

a. All showers and bath/shower combinations shall be protected from excessive mixed water temperature
due to tluctuations in supply water pressures or loss of the cold water supply. Protection shall be provided by
thermostatic, pressure balancing, or combination control valves which shall reduce or shut off the mixed water
supply if unsafe conditions occur. Valves shall have an adjustable stop to limit the movement of the control
handle toward the full hot position. Thermostatic control valves shall have a maximum limit setting of 120F.
Pressure balancing control valves shall be adjusted after installation to provide not more than 120F outlet
temperature with normal water pressures and temperatures available.
b. Individual shower and bath/shower control valves shall comply with ASSE 1016.
c. Multiple showers when supplied by a single tempered water supply pipe shall be protected by a master
thermostatic control valve having a maximum setting of not more than 110 F. The setting device shall be so
arranged to resist tampering. The master thermostatic control shall comply with the standard listed in Table
3.1.3. A single family dwelling unit with a mixing valve that serves the entire building, located at the hot water
heater, will not satisfy requirements of this section.
d. Water discharged from public use hand washing facilities shall be limited to a maximum temperature of
110 F.
e. Water discharge into bathtubs shall be controlled to a maximum temperature of 120 F using a device
complying with the standards listed in Table 3.1.3.
f. The temperature of water from tankless water heaters shall be controlled to permit not more than 140
F when intended for domestic uses. This provision shall not supersede the requirements of paragraphs a, b, c,
d and e above.
10.15.7 Thermal Expansion Control

Where a backtlow prevention device, check valve or water pressure regulator is installed serving water
heating equipment such that a closed system is created, a device for controlling thermal expansion shall be
installed.
EXCEPTION: Instantaneous water heaters.

a. Plastic piping used for hot water distribution shall conform to the requirements of Section 3.4 and Table
3.4. Piping shall be water pressure rated for not less than 100 psi at 180F.
NOTE: The working pressure rating for certain approved plastic piping materials varies depending on pipe
size, pipe schedule and method of joining. (See Appendix B.)
b. Plastic pipe or tube shall not be used downstream from instantaneous water heaters, immersion water
heaters or other heaters not having approved temperature safety devices.
c. Piping within six inches of tlue or vent connectors shall be approved metallic pipe or tube.
d. The normal operating pressure in water distribution piping systems utilizing approved plastic pipe or
tube for hot water distribution shall be not more than 80 psi. Where necessary, one or more pressure reducing
valves shall be provided to regulate the hot and cold water supply pressure to not more than 80 psi.
e. The pressure in the piping system shall be limited by a pressure relief valve at the water heater set no
higher than 100 psi. When the water heater is protected by a pressure relief valve or combination pressure-
temperature relief valve having a pressure setting higher than 100 psi, a separate pressure relief valve shall be
provided at the water heater to protect the piping. The relief valve shall comply with Section 10.16.2 except
that it shall be set no higher than 100 psi. Thermal expansion shall be controlled as required under Section
10.15.7.
2003 National Standard Pumbing Code-JI/ustrated 239

10.15.9 Drip Pans
10.15.9.a Where Required
Where water heaters or hot water storage tanks are installed in locations where leakage will cause
damage to the building structure, the tank or water heater shall be installed in a drip pan in accordance
with Section 1O.15.9.b.
10.15.9.b Construction
I. Drip pans shall be watertight and constructed of corrosion-resistant materials. Metallic pans shall be
24 gage minimum. Non-metallic pans shall be .0625-inch minimum thickness. Pans shall be not less
than I-Y2"deep and shall be of sufficient size to hold the heater without interfering with drain valves,
burners, controls, and any required access.
2. High impact plastic pans shall be permitted under gas-fired water heaters where the heater is listed
for zero clearance for combustible floors and the application is recommended by the pan manufacturer.
10.15.9.c Drainage
Drip pans shall have drain outlets not less than %" size, with indirect drain pipes extending to an
approved point of discharge, a suitably located indirect waste receptor, or floor drain, or extend to
within 2 to 6 inches above the adjacent floor.
Discharge from a relief valve into a water heater pan shall be prohibited.
10.15.10 Water Heaters Used for Space Heating

a. Water heaters used for space heating shall be listed for such use.
b. Piping and components connected to a water heater for space heating application shall be suitable for
use with potable water.
c. Where required, a water temperature control valve shall be installed in every combination water
heating-space heating system application to limit domestic hot water temperature to 140oP.The temperature
control device shall be an ASSE 1017listed device.
10.16 SAFETY DEVICES FOR PRESSURE VESSELS
10.16.1 TankProtection
Pressure vessels used for heating water or storing water at pressures above atmospheric shall be protected
by approved safety devices in accordance with one of the following methods:
a. A separate pressure relief valve and a separate temperature relief valve; or
b. A combination pressure and temperature relief valve; or
c. Either "a" or "b" above and an energy cut-off device.
d. Tank construction conforming to a standard that does not require a temperature or pressure safety or
relief valve.
10.16.2 Pressure Relief Valves

a. Pressure relief valves shall comply with the applicable codes, standards, and ratings of ASME, ANSI,
and AGA.

b. The valves shall have a relief rating adequate to meet the pressure conditions in the equipment served,
and shall be installed either directly in a top tank tapping or in the hot or cold water piping close to the tank.
c. There shall be no shutoff valve between the pressure relief valve and the tank.
d. The pressure relief valve shall be set to open at not less than 25 p.s.i. above the street main pressure or
not less than 25 p.s.i. above the setting of any house water pressure regulating valve.
e. The setting pressure relief valve shall not exceed the rated working pressure of the tank being pro-
tected.
See Figure 10.16.6
Comment: If a separate pressure relief valve is installed on a water heater storage tank, there must be no
shutoffvalves between it and the pressure tank. Also, there must be no shutoffvalve in its discharge line
WATER HEATER
'\ SHUT OFF VALVE

HW
\1 lcw
PRESSURE HW .CW
NOTE 2 --"""
/ RELIEF VAVL WATER HEATER
NOTE 2 ~ SHUT OFF VALVE
j
TEMPERATURE COMBINATION
RELIEF VAVLE -' P & TVALVE
II II
WATER
HEATER
NO THREADED END
II
AIR GAP
II
WATER
HEATER . ----
/ NO THREADED END
AIR GAP
NOTES
NOTES 1,5,6
II
NOTE 7 1 1,5,6
i
lL lL
SEPARATE RELIEF VALVES A COMBINATION RELIEF VALVE
NOTES:
1. Reliefvalves can discharge to the floor where permitted bythe Authority Having Jurisdiction.
2. A shutoff valve in the hot water supply is permitted.
3. Shutoff valves must not isolate relief valves from the tank that they are protecting.
4. Threads are prohibited on the ends of reliefvalve discharge pipes to prevent the installation of a pipe
cap if the valve begins to leak.
5. Drains or indirectwaste pipes that receive the discharge from relief valves must be sized according
to Table 10.16.6,based on the size of the relief valve discharge pipe.
6. The inlet to indirect waste piping must be elevated to establish sufficient static head above the
horizontal portion of the drain to prevent spillage.
7. Where two indirectwaste pipes from relief valves arejoined, the cross-sectional area of the common
drain must be equal to or larger than the sum of the areas of the individual waste pipes. Refer to
Section 9.3.6.b.
Figure 10.16.6
WATER HEATER RELIEF VALVES AND DISCHARGE PIPING

10.16.3 Temperature Relief Valves
Temperature relief valves shall be of adequate relief rating, expressed in BTU/HR, for the equipment served.
a. Shall be installed so that the temperature sensing element is immersed in the hottest water within the top
6 inches of the tank.
b. The valve shall be set to open when the stored water temperature reaches a maximum of 210F. (See
Section 3.3.10.)
c. These valves shall conform to an approved standard and shall be sized so that when the valve opens,
the water temperature cannot exceed 210F with the water heating equipment operating at maximum input.
See Figure 10.16.6
10.16.4 Combination Pressure-Temperature Relief Valves

Combination pressure-temperature relief valves shall comply with all the requirements ofthe separate pres-
sure and temperature relief valves. (See Section 3.3.10.) See Sections 10.16.2 and 10.16.3
10.16.5 Reserved
10.16.6 Relief Valve Discharge Piping

a. Piping from the outlet of relief valves to the point of disposal shall be of a material approved for
potable water (see Section 3.4). Discharge pipes from temperature relief valves or combination temperature-
pressure relief valves shall be listed in Table 3.4 for hot water use.
EXCEPTION: Any pipe that is rated to convey water at 210F to an open discharge, including black steel
pipe.
b. There shall be no shut-off valve, check valve or other restricting device between a relief valve and the
pressure vessel or piping system being protected.
c. The discharge pipe shall be no smaller than the outlet size of its relief valve and shall extend to a point
of disposal without valves, traps or rises that would prevent the relief valve from draining by gravity. Dis-
charge end ofthe pipe shall not be threaded.
d. An air gap shall be provided where relief valves discharge into an indirect waste pipe, floor drain,
trench drain, service sink, mop basin, laundry sink, standpipe or other approved receptor. The minimum size of
fixture drains or waste pipes that receive the discharge from relief valves shall be as indicated in Table
10.16.6.
e. Where relief valves discharge to the floor, the discharge pipe shall terminate not more than 6 inches nor
less than 2 inches above the floor.
f. If the point of disposal is outside the room or space in which the relief valve is located, an indirect
gravity drain shall be provided from the room or space to the point of disposal. Indirect waste pipes shall be
sized according to Table 10.16.6 and shall be of a material approved for potable water, sanitary drainage or
storm drainage (see Tables 3.4, 3.5, and 3.7). A visible air gap shall be provided in the room or space in which
the relief valve is located.
EXCEPTION: Where water heaters are located above ceilings, the relief valve discharge pipe shall extend to
a point of disposal or indirect waste that is readily observable in an area below the heater.
g. Where two or more relief valves serving independent systems are located in the same area, each shall
be discharged separately. Where such relief valves for independent systems are discharged into a common
gravity drain or indirect waste pipe, the drain or waste pipe shall be sized according to the largest discharge
pipe served.
See Figure 10.16.6

TABLE 10.16.6
SIZE OF DRAINS OR WASTE PIPES RECEIVING RELIEF VALVE DISCHARGE
Minimum Drain or
Discharge Pipe Size Indirect Waste Size
3/4 " 2"*
1" 3"
1-1/2 " 4"
2" 4"
2-1/2 " 6"
*EXCEPTION: A laundry sink with 1-1/2" waste pipe.
10.16.7 Vacuum Relief Valves

Where a hot water storage tank or an indirect water heater is located at an elevation above the fixture outlets
in the hot water system, a vacuum relief valve shall be installed on the storage tank or heater. See Figure
10.16.7
WATER HEATER VACUUM RELIEF VALVE

~ VACUUM RELIEF VALVE /
SHUT OFF VALVE ~
HW
HW CW
COMBINATION COMBINATION
~ P&TVALVE P & T VALVE
I
WATER I WATER HEATER WATER
HEATER I HEATER
I DIP TUBE SHUT OFF VALVE ~

I
CW
~I= ~
cw
,
HWTO CW HWTO
FIXTURES BELOW FIXTURES BELOW
TOP FEED HEATER BOTTOM FEED HEATER
NOTES:
1. Vacuum reliefvalves at water heaters prevent vacuum conditions that could siphon water from a
tank, causing it to be damaged from dry firing or collapse.
2. Vacuum relief valves are tested and rated underANSI Z21.22 - Relief Valves for Hot Water Supply
Systems.
3. Backflow preventionvacuum breakersare not intendedfor use asvacuum reliefvalves.
4. Vacuum relief valves must be mounted higher than the tank being protected.
Figure 10.16.7
VACUUM RELIEF VALVES ON OVERHEAD WATER HEATER TANKS
2003 National Standard Pumbing Code-I/lustrated 243

10.16.8 Replacement of Relief Valves
a. Reliefvalves shall be maintained in proper working order and shall be replaced when necessary.
b. Whenever a water heater is replaced, its temperature relief valve and pressure relief valve, or combina-
tion temperature-pressure relief valve shall also be replaced and shall not be reused.
10.17MANIFOLD-TYPE PARALLEL WATER DISTRIBUTION SYSTEMS
10.17.1 General
Parallel water distribution systems shall provide individual hot and cold water lines from a manifold to each
fixture served.
a. Manifolds shall be specifically designed and manufactured for parallel water distribution.
b. Manufacturer's of such systems shall provide complete sizing and installation instructions, including any
limitations or restrictions on use.
c. Piping materials shall include coiled plastic or copper tube approved for hot and cold water distribution.
10.17.2 Sizing
See Appendix B for sizing manifolds and distribution lines. Distribution line sizes shall be as recommended by
the system manufacturer to provide the fixture water flow rates listed in Section IO.14.2a. The minimum line
size shall be 3/8" nominal.
10.17.3 Valving
a. Each manifold outlet shall be equipped with a shut-off valve that identifies the fixture being supplied.
Additional shut-off valves at the fixtures may be omitted.
b. Manifolds shall be readily accessible.
10.17.4 Support
a. Tube bundles for manifold systems shall be supported in accordance with Chapter 8 of this Code.
b. Supports at changes in direction shall be in accordance with the manufacturer's recommendations.
10.18 DRINKING WATER TREATMENT UNITS
10.18.1 Compliance with Standards

Drinking water treatment units shall comply with the standards listed in Table 3.1.3.
10.18.2 Air Gap Discharge

Discharge from all drinking water treatment units shall be installed with an air gap.
EXCEPTION: Reject water connections from reverse osmosis drinking water treatment units shall be
through an air gap or alternate air gap device in accordance with the requirements of ANSI/NSF 58.
10.18.3 Connection Tubing

The tubing to and from the drinking water treatment unit shall be of a size and material as recommended by
the manufacturer. The tubing shall comply with NSF 14, NSF 58 or NSF 61.

10. 19 SIZING OF RESIDENTIAL WATER SOFTENERS
Residential-use water softeners shall be sized per Table 10.19.
TABLE 10.19
SIZING OF RESIDENTIAL SOFTENERS
1
Required Size of Softener Connection (in.) Number of Bathroom Groups Served
1/4 2
Up to 2
3
Up to 4
1 Installation with a kitchen sink and dishwasher, laundry tray and automatic clothes washer.
2 An additional water closet and lavatory shall be permitted without an increase in sizing.
3 Over four Bathroom Groups, the softener shall be engineered for the specific installation.

Blank Page

>,Ch~pter 11
Sanitary Drainage Systems

11.1 MATERIALS
See Section 3.1. See Section 3.5 and Table 3.5 for approved materials for sanitary drainage piping
11.2 BUILDING SEWERS
11.2.1 Sewer or Drain in Filled Ground

Building sewers or building drains which are installed in filled or unstable ground shall be installed in accor-
dance with Section 2.6.
11.2.2 Existing Building Sewers and Drains

Existing building sewers and drains may be used in connection with new building sewer and drainage systems
only when found by examination to conform to the new system in quality of material prescribed by this Code.
11.2.3 Building Sewer and Building Drain Size

The size of the building sewer and the size of the building drain shall be determined by fixture unit loads
connected in accordance with Table 11.5.1A. See Figures 11.5.1 - A and - B
11.3 DRAINAGE PIPING INSTALLATION
11.3.1 Slope ofHorizontal Drainage Piping

Horizontal drainage piping shall be installed in uniform alignment at uniform slopes not less than 1/4 inch per
foot for 3-inch size and smaller, and not less than 1/8 inch per foot for 4-inch size and larger. Where condi-
tions do not permit building drains and sewers to be laid with slope as great as that specified, a lesser slope
may be permitted by the Authority Having Jurisdiction. See Appendix K for the approximate discharge
rates and flow velocities in drains at various slopes.
11.4 FIXTURE UNITS
11.4.1 Load on Drainage Piping

The load on drainage system piping shall be computed in terms of drainage fixture unit values in accordance
with Table 11.4.1 and Section I 1.4.2.
11.4.2 Conversion of Flow in GPM to DFU

Where the discharge rate of fixtures or equipment is expressed in gallons per minute (GPM), two (2) drainage
fixtures units (DFU) shall be allowed for each gallon per minute (GPM) offlow.

TABLE 11.4.1
ORAINAG E FIXTURE UNIT (OFU) VALVES
HEA VY-USE ASSEMBLY

SERVING30RMOREOWEL
"6",,.
GRAVITY-TANK WATER CLOSETS '/

1 1/2 Bathrooms 6.0

2 Bathrooms 7.0
2 1/2 Bathrooms 8.0

3 Bathrooms 9.0
BA THROOM GROUPS HAVING 1.6 GPF

nS:FT E" LX,/./;,;it,
'<i,iCLe d"
1 Bathroom Group 5.5 3.5
1 '/2 Bathrooms 6.5

2 Bathrooms 7.5
2 1/2Bathrooms 8.5
3 Bathrooms 9.5
Each Additional 1/2Bath 0.5

n
;.,' 'iT"'3.5'(}J>!+i F'!?!
TANK-TYPE WATER CLOSETS
Half-bath or Powder Room
J:!f!:!1'
3.0 2.0
I '/2 Bathrooms 8.0

2 Bathrooms 10.0
2 '/2 Bathrooms 11.0

3 Bathrooms 12.0
BATH GROUP(1.6GPF Flushometer Valve) 5.0 3.0
BATH GROUP (3.5 G PF Flushometer Valve) 6.0 4.0

TABLE 11.4.1 (Continued)
DRAINAGE FIXTURE UNIT (DFU) VALUES
HEAVY-USEASSEMBLY
TYPEOF FIXTURES OTHER THAN DWELLINGUNITS
SERVING3 OR MORE DWELLINGUNITS
INDIVIDUAL FIXTURES ;; '!fII!fFcc J1 '}'(}!f0!f0
Bathtub or Combination Bath/Shower, ] '/," Trap 2.0 2.0
Bidet, I'h" Trap 1.0 1.0

Clothes Washer, Domestic, 2" Standpipe 3.0 3.0 3.0
Dishwasher, Domestic, with Independent Drain 2.0 2.0 2.0
Drinking Fountain or Watercooler 0.5
Food-Waste-Grinder, Commercial, 2" Min Trap 3.0
Floor Drain, Emergency 0.0
Kitchen Sink, Domestic, with One I '/," Trap 2.0 2.0 2.0
Kitchen Sink,Domestic, with Food-Waste-Grinder 2.0 2.0 2.0
Kitchen Sink,Domestic, with Dishwasher 3.0 3.0 3.0
Kitchen Sink, Domestic,with Grinder and Dishwasher 3.0 3.0 3.0
Laundry Sink, One or Two Compartments, I '/," Waste 2.0 2.0 2.0
Laundry Sink, with Discharge from Clothes Washer 2.0 2.0 2.0
Lavatory, ] '1." Waste 1.0 1.0 1.0 1.0
Mop Basin, 3" Trap 3.0
Service Sink, 3" Trap 3.0
Shower Stall, 2" Trap 2.0 2.0 2.0
Showers, Group, per Head (Continuous Use) 5.0
Sink, ] '/," Trap 2.0 2.0 2.0
Sink, 2" Trap 3.0 3.0 3.0
Sink, 3" Trap 5.0
Trap Size, 1'/,' (Other) 1.0 1.0 1.0
Trap Size, I'/''' (Other) 2.0 2.0 2.0
Trap Size, 2" (Other) 3.0 3.0 3.0
Trap Size, 3" (Other) 5.0
Trap Size, 4" (Other) 6.0
Urinal, 1.0 GPF 4.0 5.0
Urinal, Greater Than 1.0 GPF 5.0 6.0
Wash Fountain, I '/," Trap 2.0
Wash Fountain, 2" Trap 3.0
. Wash Sink, Each Set of Faucets 2.0

TABLE 11.4.1 (Continued)
DRAINAGE FIXTURE UNIT (DFU) VALUES
HEAVY-USE ASSEMBLY
C{>: . 7' .'.."7j
Water Closet, 1.6 GPF Gravity or Pressure Tank 3.0 3.0 4.0 6.0
Water Closet, 1.6 GPF Flushometer Valve 3.0 3.0 4.0 6.0
Water Closet, 3.5 GPF Gravity Tank 4.0 4.0 6.0 8.0
Water Closet, 3.5 GPF Flushometer Valve 4.0 4.0 6.0 8.0
Whirlpool Bath or Combination Bath/Shower, I '10" Trap 2.0 2.0
NOTES: (Table 11.4.1):

I. A Bathroom Group, for the purposes of this Table, consists of not more than one water closet, up to two lavatories, and either one
bathtub, one bath/shower combination, or one shower stall. Other fixtures within the bathing facility shall be counted separately to
I
determine the total drainage fixture unit load.
2. A Half-Bath or Powder Room, for the purposes of this Table, consists of one water closet and one lavatory.
3. For unlisted fixtures, refer to a listed fixture having a similar flow and frequency of use.
4. When drainage fixture unit (DFU) values are added to determine the load on the drainage system or portions thereof, round the sum to the
nearest whole number before referring to Tables 11.5.1 A, 11.5.1 B, or 12.16.6A for sizing the drainage and vent piping. Values of 0.5 or
more should be rounded up to the next higher whole number (9.5 = 10 DFU). Values of 0.4 or less should be rounded down to the next
lower whole number (9.4 = 9 DFU).
5. "Other Than Dwelling Units" applies to business, commercial, industrial, and assembly occupancies other than those defined under
"Heavy-Use Assembly." Included are the public and common areas in hotels, motels, and multi-dwelling buildings.
6. "Heavy-Use Assembly" applies to toilet facilities in occupancies which place heavy, but intermittent, time-based loads on the drainage
system, such as; schools, auditoriums, stadiums, race courses, transportation terminals, theaters, and similar occupancies where queuing is
likely to occur during periods of peak use.
7. Where other than water-supplied fixtures discharge into the drainage system, allow 2 DFU for each gallon per minute (gpm) of flow. (See
Section I 1.4.2.)
11.4.3 Diversity Factors

In certain structures such as hospitals, laboratory buildings, and other special use or occupancy buildings
where the ratio of plumbing fixtures to occupants is proportionally more than required by building occupancy
and in excess of 1,000 fixture units, the Authority Having Jurisdiction may permit the use of a diversity factor
for sizing branches, stacks and building sewers.
11.5.6 Restrictions on Number of Water Closets on 3" Pipe Size
a. 3" Building Drain or Sewer:
I. In single dwelling units, not over three bathroom groups shall be installed on a 3" building drain or
sewer, or branches thereof.
2. For other than single dwelling units, not over two water closets or bathroom groups shall be installed
on a 3" building drain or sewer.
EXCEPTIONS:
1. In single dwelling units, up to six bathroom groups shall be permitted where the water closets are
rated 1.6 gallons per flush (gpf) or less.

2. In other than single dwelling units, up to four water closets or bathroom groups shall be permitted
where the water closets are rated 1.6 gallons per flush or less.
b. 3" Horizontal Fixture Branch: Not over two water closets or bathroom groups shall be installed on a 3"
horizontal fixture branch.
EXCEPTION: Up to four water closets or bathroom groups shall be permitted where the water closets are
rated 1.6 gpf or less.
c. 3" Stack: Not over two water closets or bathroom groups shall be installed within each branch interval
of a 3" drainage stack, nor more than six water closets or bathroom groups on the stack.
EXCEPTION:
Up to four water closets or bathroom groups shall be permitted in each branch interval and up to twelve
water closets or bathroom groups on the stack when the water closets are rated 1.6 gpf or less.
Comment: The Authority Having Jurisdiction may permit the use of a diversityfactor in systems where
the number offixtures per person is higher than normal. A hospital is such an example where toilet
facilities are proviledin each patient roomfor the convenience of the patients. The load on the drain-
age system is created by the number of persons served, not by the number of plumbing fixtures that are
installed.

11.5 DETERMINING SIZE OF THE DRAINAGE SYSTEM
11.5.1 Selecting Size of Drainage Piping

Pipe sizes shall be determined from Table 11.5.1A and 11.5.lB on the basis of the drainage fixture unit load
(DFU) computed from Table 11.4.1 and Section 11.4.2.
EXCEPTION: Drainage pipe sizes for individual fixtures shall be not less than the minimum trap size required
in Section 5.2. See Figures 11.5.1 - A and - B
TABLE 11.5.1A
BUILDING DRAINS AND SEWERS I
Maximum Number of Fixture Units That May Be Connected to Any Portion
of the Building Drain or the Building Sewer.
Pipe Size- Slope Per Fool
Inches 1/16-lnch !l8-lnch !l4-lnch 1/2-lnch
2 21 26
.., 422 502
-'
4 180 216 250
5 390 480 575
6 700 840 1,000
8 1,400 1,600 1,920 2,300
10 2,500 2,900 3,500 4,200
12 2,900 4,600 5,600 6,700
15 7,000 8,300 10,000 12,000
I. On-site sewers that serve more than one building may be sized according to the current standards and specifications
of the Authority Having Jurisdiction for the public sewers.
2. See Section 11.5.6.a.
TABLE 11.5.1B
HORIZONTAL FIXTURE BRANCHES AND STACKS
Maximum Number of
FixtureUnits That May Be Connected to:
Stacks with More Than Three
One Stack of Branch Intervals
Any Three Branch
Pipe Size- Horizontal Intervals or Total at One
Inches Fixture Branch 1 Less Total for Stack Branch Intervals
]1/4 1 1 1 1
1112 3 4 8 2
2 6 10 24 6
3 202 483 723 203
4 160 240 .,' 500 90
5 360 540 1,100 200
6 620 960 1,900 350
8 1,400 2,200 3,600 600
10 2,500 3,800 5,600 1,000
12 3,900 6,000 8,400 1,500
15 7,000
I. Does not include branches of the building drain.

2. See Section I L5.6.b.
3. See Section 11.5.6.c.

EXAMPLE OF SIZING DRAINAGE PIPING
(Refer to Figures 11.5.I-A and -B)
1. To size the drainage system, start at the top floor and work down to the building drain.
2. Draw a diagram of the system showing the various fIXtures.
3. Assign a drainage fixture unit (DFU) value to each fIXture or fixture group using Table 11.4.1. Where a
specific fIXture type is not listed, use the "Sink" or "Trap Size" values.
4. Size the horizontal fixture branches on each floor using the pipe sizes in Table 11.5.1.B for the number of
DFUs listed in the second column.
5. Size the stacks using the pipe size in Table 11.5.1.B for the number of DFUs listed in columns 3,4, or 5,
depending on the number of branch intervals. Check the limits on DFUs in anyone branch interval and
the total for the stack. Size the stack accordingly.
6. For Stack A in Figure 11.5.I-B, each horizontal branch drain has 90 DFU and is 4" size. The stack is
4" size from top to bottom.
7. For Stack B in Figure 11.5.I-B, the horizontal branch drains are all 4" size. Although the total number
of DFUs is the same as Stack A (450 DFU), the lowest branch interval has more than 90 DFU and must
be 5" size. The stack cannot be smaller than any of its branches and thus must be 5" size at the base.
The upper portions of the stack can be 4" size.
8. For Stack C in Figure 11.5.I-B, although the total number of DFUs is less than Stack A and Stack B, the
top horizontal branch drain must be 5" size because it has 200 DFUs. The entire stack must 5" size,
even though 4" would have been adequate for the total number of DFUs.
9. Stack D in Figure 11.5.I-B only has three branch intervals and can be sized using column 3 in Table
11.5.1.B. Each of the 3" horizontal fIXture branches is limited to four 1.6 GPF water closets per Section
11.5.6.b. Each branch interval of the 3" stack is limited to four 1.6 GPF water closets and the entire 3"
stack is limited to twelve 1.6 GPF water closets per Section 11.5.6.c. If the number of water closets on
any branch or the stack exceed the limits for 3" pipe, the branch and downstream stack must be in-
creased to 4" size.
10. In Figure 11.5.I-A, Stack A is 4" size with 450 DFUs. In Table n.5.1.A, Branch A of the building drain
must be 5" size sloped 114"per foot. If 114" slope cannot be maintained, the branch must be increased to
6" size sloped 118" per foot.
11. In Figure n.5.I-A, Stack B is 5" size with 450 DFUs. In Table n.5.1.A, Branch B of the building drain
can remain 5" size if sloped 114"per foot. Otherwise, the size must be increased if run at less slope.
12. In Figure 11.5.I-A, Section B-C of the building drain is 450 + 450 = 900 DFUs. In Table 11.5.I.A, it
needs to be 8" size, but the slope can be reduced to 118"per foot.
13. In Figure n.5.I-A, Stack Cis 5" size with 404 DFUs. In Table 11.5.1.A, Branch C can remain 5" size,
but must be sloped at 114"per foot. Otherwise, the size must be increased if run at less slope.
14. In Figure 11.5.I-A, Section C-D of the building drain is 900 + 404 = 1304 DFUs. Section C-D of the
building drain must be at least 8" size because Section B-C is 8" size. In Table n.5.1.A, 8" size is
adequate at 118" or 1116" per foot slope. Section 11.3.1 requires 118" slope for pipe 4" and larger.
However, Table K-I indicates that the velocity in Section C-D when flowing 112full at 1116" slope is not
less than the 2 feet per second minimum and the reduced slope might be approved by the Authority
15. In Figure 11.5.I-A, Stack D is 3" size with 48 DFUs. In Table 11.5.I.A, branch D of the building drain
could remain 3" if sloped 112" per foot. However, Section 11.5.6a limits it to four 1.6 GPF water closets.
Otherwise, it would have to be increased to 4" size.
16. In Figure n.5.I-A, Section D-E of the building drain is 1304 + 48 = 1352 DFUs. Section D-E must be
at least 8" size because Section C-D is 8" size. In Table 11.5.I.A, 8" size is still adequate for 1352
DFUs.
17. In Figure 11.5.I-A, horizontal fIXture branch E is 4 + 1 + 4 + 1 = 10 DFUs. In Table 11.5.1.B, the
branch needs to be 3" size. It has less than the allowable number of water closets in Section 11.5.6.b.
18. In Figure n.5.I-A, the load on the last section of the building drain and the building sewer is 1352 + 10
= 1362 DFUs. The 8" size of Section D-E is still adequate for the final section of the building drain and
for the building sewer.

STACKA
l'
I
STACKB I
l'
I
STACKC I
l'
STACK D I
I
/BUILDING DRAIN
/ BRANCHA
'- BUILDING DRAIN(B-C)
'- BUILDING DRAIN(C-D)
I l'
Ii" I
" BUILDING
DRAIN ~
'1
I
"-
""
"-
" --- HORIZONTAL
FIXTURE BRANCH E
Figure 11.5.1 -A
SIZING BUILDING DRAINS AND SEWERS

STACK"A" STACK"B" STACK"C"
I STACK"D"
I I I
I I I I
I I I I
I 4" -90 DFU I 4" - 90 DFU I 5" - 200 DFU
I
- 90 DFU-4" 1- 90 DFU4" 1-5"

I
I
I
4" -90 DFU 4" - 90 DFU 3" - 20 DFU
- 180 DFU-4" C::U

-180DFU4" -5" - 20DFU3"
4"-90DFU 4" - 85 DFU 3" -18 DFU 3" - 8 DFU
- 270 DFU-4" - 265 DFU 4" -5"

- 28DFU3"
4" -90 DFU 4" - 85 DFU 2" - 6 DFU 1 3" - 20 DFU
- 360 DFU-4" - 350 DFU 4" -5"
4" -90 DFU 5" -100 DFU 4" - 90 DFU

,
- 450 DFU-4" - 450 DFU-5" -5" 1- 48DFU-3"
TOTAL -450 DFU TOTAL - 450 DFU TOTAL - 404 DFU TOTAL- 48 DFU
Figure 11.5.1 - B
SIZING DRAINAGE STACKS

11.5.2 Minimum Size of Soil and Waste Stacks
Soil or waste stacks shall not be smaller than the largest horizontal branch connected thereto, except that:
a. A 3" x 4" water closet bend shall not be considered a reduction in pipe size.
b. A 4" horizontal drain to a 3" soil stack by means of a 3" x 4" tee-wye, or to above the center line of a 3"
horizontal drain by means of a 3" x 4" wye shall be acceptable, provided that the 4" drain does not receive the
discharge of any stack and that it receives only the discharge of fixtures located on the floor or wall immedi-
ately above the 4" drain. Such 4" horizontal drain lines shall be loaded, sloped, and vented as if the 4" drain
were a 3" horizontal drain.
See Figure 11.5.2
,..
I
I
I
-- STACK VENT (NOTE 5)
I
I
I
--- 30 D.F.U. 4" HORIZONTAL
FIXTUREBRANCH(NOTE 2)
~ 4" SOIL OR WASTE STACK (NOTE 3)

4" BUILDING DRAIN (NOTE 4)
NOTES:
1. The figure shows a sanitary drainage piping system with one branch interval.
2. The horizontal branch drain with 30 DFU must be 4" minimum size per Table 11.5.1 B.
3. The stack size must be 4" minimum size, even though Table 11.5.1 B indicates that a 3" stack with
one branch interval could handle 48 DFU.
4. The building drain must be 4" minimum size, even though Table 11.5.1 A indicates that a 3" building
drain could handle 42 DFU at 1/4" slope.
5. The stack vent must be 2" minimum size, which is 1/2 the size of the 4" drainage stack.
Figure 11.5.2
MINIMUM SANITARY DRAINAGE PIPE SIZES
11.5.3 Reserved

11.5.4 Provision for Future Fixtures
When provision is made for the future installation of fixtures, those provided for shall be considered in deter-
mining the required sizes of drain and vent pipes. Construction to provide for such future installation shall be
terminated with a plugged fitting or fittings. See Figure 11.5.4
Comment: Drainage or vent piping installed with plugged or cappedfittings for the connection of future
fIXtures does not constitute a dead end. Such piping should be accessible.
~-~ ,--~
I
I PLUGGED OR CAPPED
PIPING SIZED FOR
FUTURE FIXTURE I CONNECTIONS FOR
I FUTURE FIXTURE
u
1- ~
WASTE
Figure 11.5.4
DRAIN AND VENT PROVISIONS FOR FUTURE FIXTURES
11.5.5 Minimum Size of Underground Drainage Piping

No portion of the drainage system installed underground shall be less than two inches pipe size.
EXCEPTION: Condensate wastes and piping which receives the discharge from relief valves after the air
gap.
11.5.6 Restrictions on Number of Water Closets on 3" Pipe Size

a. Not more than four water closets or bathroom groups shall be permitted on a 3" horizontal fixture
branch,.
EXCEPTION: Not more than two water closets or bathroom groups shall be permitted where the water
closets are rated 3.5 gallons per flush or more.
b. Not more than four water closets or bathroom groups shall be permitted in each branch interval of a 3"
drainage stack.
c. Not more than twelve water closets or bathroom groups shall be permitted on a 3" drainage stack.
EXCEPTION: Not more than six water closets or bathroom groups shall be permitted where the water
d. In single dwelling units, not more than six bathroom groups shall be connected to a 3" building drain or
sewer, or branches thereof.
EXCEPTION: Not more than three bathroom groups shall be permitted where the water closets are rated
3.5 gallons per flush or more.
e. For other than single dwelling units, not more than four water closets or bathroom groups shall be
connected to a 3" building drain or sewer, or branches thereof.

f. Where drainage piping serves a mixture of 1.6 GPF water closets and 3.5 GPF (or higher) water
closets, the 3.5 GPF (or higher) fixtures shall be counted as two water closets for the purpose of determining
the total number of water closets on the drain or stack.
11.5.7 Stack Size Reduction

a. Stacks shall be sized according to the total accumulated drainage fixture unit load (DFU) at each story
or branch interval.
b. The stack size shall be permitted to be reduced as the DFU load decreases on the upper portion ofthe
stack.
EXCEPTION: No portion of a stack shall be less than one-half of the required size at the base of the stack.
11.6 SIZING OF OFFSETS ON DRAINAGE PIPING
11.6.1 Vertical Offsets or Change of Direction

a. An offset in a vertical stack, with a change of direction of 45( or less from vertical, shall be sized as a
straight vertical stack.
b. Where stacks have 10 or more branch intervals, if a horizontal branch connects to the stack within two
feet above or below the offset, a relief vent shall be provided in accordance with Section 12.3.3. See
Figure 11.6.1
FROM UPPER FLOORS
8TH FLR
N~TE I
OFFSET OF 450 OR MORE FROM
HORIZONTAL CAN BE SIZED AS A
STRAIGHT VERTICAL STACK
NO~
7TH FLR
L 1
TO LOWER FLOORS
NOTES:
1. Vertical offsets in drainage stacks do not affect the stack size.
2. If a drain stack with five or more branch intervals above a vertical offset has fixtures or horizontal
branches connected within two feet above or below the offset, a relief vent must be provided for the
lower portion of the stack.
Figure 11.6.1
VERTICAL OFFSETS IN DRAINAGE STACKS

11.6.2 Reserved
11.6.3 Offsets Above the Highest Branch
An offset in a stack above the highest horizontal branch drain connection shall not affect the size of the stack,
only the developed length of the stack vent. See Figure 11.6.3
.JiLVTR.
-1-
J '
// I
/ I
/ I
( II
HIGHEST I
FIXTURE
BRANCH FIXTURE
BRANCH
- STACKTO LOWER FLOOR
NOTES:
1. The offset does not affect the size of the stack, only its developed length.
Figure 11.6.3
OFFSETS IN STACKS ABOVE THE HIGHEST BRANCH DRAIN CONNECTION
11.6.4 Reserved
11.6.5 Horizontal Offsets
a. A stack with an offset of more than 45 from the vertical shall be sized as follows:
1. The portion of the stack above the offset shall be sized as for a regular stack based on the total number
of fixture units above the offset.
2. The offset shall be sized as for a building drain (See Table 11.5.1A).
3. The portion ofthe stack below the offset shall be sized as for the offset or based on the total number of
fixture units on the entire stack, whichever is the larger.
4. A relief vent for the offset shall be installed as provided in Section 12.3.3.
See Figure 11.6.5

I
I
I I
I
I : 0
I
I
I
I
I
I I I
I I I
VENTSTACK--I I I
I I I
I I I
I I I
1 1- NOTE6-1
f' I ~
3 FEET MIN I :
I I
i
I
I
ALTERNATE
YOKE VENT
/11
I \
I
~ LOFFSET ~
(NOTE 7) I
1
I
I
I
I
I
I
I
I @
I
NOTES:
1. A horizontal offset is one that is less than 45 degrees from horizontal.
2. Vents for the branch drains and required cleanouts are not shown in the Figure.
3. The upper portion of the stack (A-B) is sized based on either the total number of drainage fixture
units (DFU) in each branch interval or the total accumulated load on the upper portion of the stack
per Table 11.5.1.B. The stack size can be reduced as it rises, up to 1/2 size in accordance with
Section 11.5.7.
4. The horizontal offset (B-C) must be sized as a building drain per Table 11.5.1.A, based on the total
drainage fixture units (DFU) above the offset.
5. The lower portion of the stack (C-D) cannot be smaller than the size of the horizontal offset. The
lower portion must be sized based on either the size of the horizontal offset, the total drainage
fixture units (DFU) in each branch interval of the lower portion, or the total accumulated load on the
upper and lower portions of the stack per Table 11.5.1. B, whichever is larger. The stack size can be
reduced as it rises, up to 1/2 size in accordance with Section 11.5.7.
6. The stack offset must be vented The upper and lower portions of the stack can be vented sepa-
rately in accordance with Section 12.3.3.a.
7. An alternate vent for the lower portion of the stack can be a yoke vent below the offset that connects
to the vent stack at least 3 feet above the offset. The 3 foot elevation reduces the possibility of
spillover from the drain stack into the vent stack.
Figure 11.6.5
HORIZONTAL OFFSETS IN STACKS

11.7 SUMPS AND EJECTORS
11.7.1 BuildingSubdrains
a. Building sanitary drains that cannot be discharged by gravity shaH be discharged into a sump pit from
which the contents shaH be lifted and discharged into the building gravity drainage system by automatic
pumping equipment or by an equally efficient method approved by the Authority Having Jurisdiction.
b. Only drains that must be lifted for gravity discharge shall be connected to such sump pits. All other
drains shaH discharge by gravity.
c. Sump pits shall be a minimum of 15 inches in diameter and 18 inches deep, and be accessible, tightly
covered, and vented.
See Figure 11.7.1
LAV LAV
W.C. W.C.
--- STACK CONNECTED TO GRAVITY DRAIN

EVEN THOUGH IT MAY BE MORE
CONVENIENT TO CONNECT IT TO THE
AUTOMATICPUMP
I
I
BUILDING DRAIN .i
I
I
-- VENT THRU ROOF OR
COMBINE WITHOTHER
I VENTS,SIZEPERSECTION
FULLPORT
SHUT OFF VALVE~
.
I
I
12.14ANDTABLE12.14.2 I
I
-- VENT THRU ROOF OR
COMBINEWITHOTHER
CHECK VALVE- I LAV VENTS
I
SEALED COVER I W.C.
AUTOMATIC SEWAGE
PUMP INSUMP - L BUILDINGSUB-DRAIN
BELOW SEWER
NOTES:
1. Sewage pumps and ejectors must have audible, visual, or combination high level alarms per Section
11.7.11.
Figure 11.7.1
A BUILDING SUBDRAIN AND SEWAGE PUMP
11.7.2 Reserved
11.7.3 Reserved

11.7.4 Venting
Building subdrain systems shall be vented according to Chapter 12 of this Code.
Comment: Sump pits with centrifugal sewage pumps must be vented in accordance with Section 12.14.2
and Table 12.14.2. Pneumatic sewage ejectors must be separately vented according to Section 12.14.3.
11.7.5 Reserved
11.7.6 GrinderPumpEjector
a. Grinder pumps shall be permitted to be used when approved by the Authority Having Jurisdiction and
installed according to the manufacturer's recommendations.
b. The rated flow velocity for grinder pump discharge piping shall be not less than 2 feet per second.
c. The size of grinder pump discharge piping shall be:
1. 1-1/4" size for up to 25 gallons per minute.
2. 1-1/2" size for up to 35 gallons per minute.
3. 2" size for up to 65 gallons per minute.
11.7.7 Pneumatic Ejectors

Vents from pneumatic ejectors shall be carried separately to the open air as a vent terminal in accordance
with Section 12.14.2.
11.7.8 Sewage Ejectors or Sewage Pumps

a. A sewage ejector or sewage pump receiving the discharge from a water closet or urinal shall have a
minimum capacity of20 gallons per minute.
b. The discharge piping from a sewage ejector and sewage pump shall include a backwater valve and a
full-way shutoffvalve.
c. Ejectors or pumps in single dwelling units shall be capable of passing a 1-1/2 inch diameter solid.
EXCEPTION: Grinder pumps.
d.In other than single dwelling units, ejectors and pumps shall be capable of passing a 2 inch diameter
solid.
EXCEPTION: Grinder pumps.
11.7.9 Individual Fixture Ejector or Pump

a. Individual fixtures other than water closets, urinals, and similar fixtures, may discharge directly into an
approved fixture-mounted ejector or pump, or into receptors having ejectors or pumps.
b. The discharge piping from a sewage ejector or sewage pump for an individual fixture shall be sized on a
hydraulic basis and include a backwater valve and full-way shutoff valve.
c. Direct-mounted equipment may be manually or automatically operated.
d. The installation of manually or automatically operated equipment shall not be subject to the venting
requirements of this Code, but shall be vented only as required for proper operation of the equipment.
e. A vent on the fixture side of the trap may terminate locally in the area served.
f. If the equipment provides a proper water seal, additional traps are not required.
See Figure 11.7.9

GRAVITY
DRAIN
-
SIZE RECOMMENDED
BY MANUFACTURE
FULL WAY
SHUTOFF VALVE
CHECK VALVE
-I
DIRECT MOUNTED FLOOR MOUNTED

FIGURE 11.7.9
INDIVIDUAL FIXTURE DRAIN PUMPS
NOTES:
1. Individualfixture drain pumps should be installed in accordance with the manufacturer's instructions.
2. Traps and vents should be installedwhen recommendedbythe pump manufacturer.
3. Manufacturers generally require screens on the sink outlet and lint filters on washing machine
discharges to prevent clogging the pump.
Figure 11.7.9
INDIVIDUAL FIXTURE DRAIN PUMPS
11.7.10 Macerating Toilet Systems

a. Macerating toilet systems shall be subject to the approval of the Authority Having Jurisdiction.
b. The sump for macerating toilets shall be vented with a 1-114"vent.
c. The discharge line from the sump shall be not less than 3/4" size and include a check valve and full-way
shutoff valve.
d. The distance from a macerating toilet system to a gravity drainage system shall not exceed the recom-
mendations of the manufacturer of the macerating toilet system.
11.7.11High Water Alarms

All ejector or pump systems shall be provided with an audible, visual, or combination high water alarm device.
11.8 RESERVED
11.9BRANCH CONNECTIONS NEAR BASE OF STACKS

a. Horizontal branch drain connections shall not be made within 10 pipe diameters downstream from the base
of a stack.
b. A relief vent shall be provided for stacks of five or more branch intervals, either above the base of the stack
or within 10 pipe diameters downstream from the base of the stack.
c. Branch drains shall not connect between the base of a stack and its relief vent.
See Figures 11.9 and 12.3.1

AIR
./1 LIQUID WASTE

/I~ STACK
_.
.-.-.-
/ HYDRAULIC JUMP
-.-.-.-.-.-.-.-.-.-u .-.-.-.-
-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.. -.-.-.-
-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.
[]
VARIES TO MAXIMUM
10 X STACK DIA.
NOTES:
1. Because of "hydraulic jump", stable flow does not occur in the horizontal drain until a distance of up
to 10 times the pipe size "0" from the base of the stack.
2. "Hydraulicjump" can completely close the horizontal drain.
3. "Hydraulic jump" can occur in stacks sized for as few as 4 drainage fixture units (OFU).
4. Branch drain connections are prohibited within 10 x "0" of the base of the stack where hydraulic
jump can occur.
Figure 11.9
HYDRAULIC JUMP AT THE BASE OF DRAINAGE STACKS
11.10 BRANCH CONNECTIONS TO OFFSETS IN STACKS

a. Branch drains shall be permitted to connect to a horizontal stack offset, provided that the connection is not
less than 10 pipe diameters downstream from the upper portion ofthe stack
b. In buildings having ten branch intervals or more, horizontal offsets shall be vented according to Section
12.3.3.
c. Where branch drains connect to a vertical stack offset in buildings having ten or more branch intervals above
the offset, the offset shall be vented as required for a horizontal offset under Sections 11.6.5 and 12.3.3 of this
Code.
11.11 SUDS PRESSURE ZONES
11.11.1 General
Where suds-producing fixtures on upper floors discharge into a soil or waste stack, suds pressure zones shall
exist as described in Section 11.11.2. Fixture or branch drain connections shall not be made to such stacks in
the suds pressure zones except where relief vents complying with Section 12.15 are provided. Suds-producing
fixtures include kitchen sinks, laundry sinks, automatic clothes washers, dishwashers, bathtubs, showers, and
other fixtures that could discharge sudsy detergents.
264 200] National Standard Pumhing Code-Illustrated

Comment #1: The most likelyfIXtures to create suds pressure problems in drainage stacks are clothes
washers, dishwashers, kitchen sinks, and laundry sinks. Where liquid wastes in tall buildings include
high-sudsing detergents, the detergent is vigorously mixed with the liquid waste and air in the stack. The
liquid waste is heavier than the suds and does not carry them along with the flow. The suds will settle in
the lower portions of the drainage system, including any horizontal offsets. The air that isflowing with
the liquid waste compresses the suds and builds up pressure in the stack that can blow trap seals ifnot
relieved. Zones of the drainage and vent piping where suds pressure can exist are described in Section
11.11.2 and illustrated in Figure 11.11.2.
Comment #2: Suds pressure reliefvents in Section 12.15 are larger than ordinary ventsfor drainage
systems because the suds are heavier than air. Suds can weightfrom 2 to as much as 19pounds per cubic
foot.
11.11.2 Locations in Stacks Serving Suds-Producing Fixtures

a. Zone 1 - at offsets greater than 45 degrees from vertical. A suds pressure zone shall extend 40 pipe
diameters up the stack above the offset, 10 pipe diameters downstream from the base of the upper portion of
the stack, and in the horizontal offset, 40 pipe diameters upstream from the top ofthe lower portion of the
stack.
b. Zone 2 - at the base of a soil or waste stack. A suds pressure zone shall extend 40 pipe diameters up
the stack above its base.
c. Zone 3 - in the horizontal drain beyond the base of a soil or waste stack. A suds pressure zone shall
extend 10 pipe diameters from the base of the stack. Also, if a turn greater than 45 degrees occurs in the
horizontal drain less than 50 feet from the base of the stack, suds pressure zones shall exist 40 pipe diameters
upstream and 10 pipe diameters downstream from the horizontal turn.
d. Zone 4 - in a vent stack at the base of a soil or waste stack. Where a vent stack connects above or
beyond the base of a soil or waste stack, a suds pressure zone shall extend up the vent stack to a level equal
to the level of the suds pressure zone in the soil or waste stack.
See Figure 11.11.2

~ ..~.
) .. J..4
./"
ZONE 2 ZONE 3
ABOVE BASE OF STACK BEYOND BASE OF STACK
ZONE 1
AT STACK OFFSET GREATER THAN 45
l r VENT
DRAINAGE STACK
r TOPOF
I ZONE 1 OR 2
ZONE 1 OR2-
1 40 "D"
ZONE 3
AT TURN GREATER THAN 45 ZONE 4
WITHIN 50 FEET OF BASE OF STACK IN VENT AT BASE OF BASE OF STACK
Figure 11.11.2
THE LOCATIONS OF SUDS PRESSURE ZONES IN DRAIN AND VENT PIPING
11.11.3 Separate Stacks

Where soil or waste stacks serving suds-producing fixtures extend six or more floors above the base of the
stack or above a horizontal offset in the stack, the lowest four floors above the base or horizontal offset shaH
be drained by a separate stack. In the case of a horizontal offset, the separate stack for the four floors above
the offset may be reconnected to the main stack below the offset, provided that the point of connection is not
a suds pressure zone in either stack. See Figure 11.11.3

l'
I
I
I
I
I
I
I 16 TH
15TH
-14 TH
rI
I 13 TH
-12TH
11 TH
10 TH
l'
I
rI
OFFSET - 9TH
I I
I I SIZE "0-2"
I - OFFSET - SIZE "0-1"
I
I 8 TH
f--- NOTE1 ~
7TH
6 TH
5TH
4 TH
3 RD
2 NO
1 ST
BSMT
BUILDING DRAIN - SIZE "0-4"
- BUILDING DRAIN - SIZE "0-3"
f--- NOTE 1 ~
Figure 11.11.3
SEPARATE DRAINAGE STACKS FOR LOWER FLOORS
WHERE THERE ARE SUDS PRODUCING FIXTURES ABOVE

NOTES:
1. There should be no branch drain connectionswithin 10 pipe diameters of the base of a drainage
stack.
2. Portion 0-1 of the upper floor offset between the 8th and 9th floors must be sized as a building
drain, based on the OFUload for the upper floors above that portion of the offset.
3. Portion 0-2 of the upper floor offset between the 8th and 9th floors must be sized as a building drain
based on the OFUload for all floors above the offset.
4. Portion 0-3 of the building drain must be sized based on the OFU load for the drainage stack above
that portion of the building drain.
5. Portion 0-4 of the building drain must be sized based on the OFUfor the entire drainage stack.
Figure 11.11.3
SEPARATE DRAINAGE STACKS FOR LOWER FLOORS
WHERE THERE ARE SUDS PRODUCING FIXTURES ABOVE
11.11.4 Exceptions
The requirements of Sections 11.11 and 12.15 shall not apply to the following:
a. Stacks that are less than three stories in height.
b. Stacks in individual dwellings having their own building sewer.

Vents and Venting
12.1 MATERIALS
See Section 3.6.
12.2 PROTECTION OF TRAP SEALS
12.2.1 Protection Required

a. The protection oftrap seals from siphonage, aspiration, or back-pressure shall be accomplished by the
appropriate use of soil or waste stacks with adequate venting in accordance with the requirements of this
Code.
b. Venting systems shall be designed and installed so that at no time shall trap seals be subjected to a
pneumatic pressure differential of more than one inch of water pressure under design load conditions.
c. If a trap seal is subject to loss by evaporation, means shall be provided to prevent the escape of sewer
gas. (See Section 5.3.6.)
CD 0 0
j
I 1" NEGATIVE
PRESSURE
l.-
1"
NOTES:
(1) Trap at rest with 2" trap seal.
(2) Trap subjected to 1" suction from building drainage piping.
(3) Trap at rest with 1/2" loss of trap seal. Trap will continue to spillover and lose trap seal when
subjected to 1" suction until the trap seal is reduced to 1". The 2" initial trap seal permits the trap to
withstand 1" suction and still maintain a trap seal of at least 1".
Figure 12.2.1 - A
TRAP SEAL REDUCTION FROM 1" NEGATIVE PRESSURE

CD CD CD 0
1" POSITIVE
11
1"
t PRESSURE
----
7
t
T
t
2.M'N~. SPILLOVER WHEN
L TRAP SEAL
REMAINS
TRAP SEAL PRESSURE REMOVED
AND FLOW REVERSES
(1) Trap at rest with 2" trap seal.

(2) Trap subjected to 1" positive pressure from building drainage piping.
(3) When pressure is removed, some spillover occurs from the momentum of the trap legs equalizing.
(4) Trap will continue to spillover and lose trap seal when subjected to 1" positive pressure until the trap
seal is reduced to 1". The 2" initial trap seal permits the trap to withstand 1" positive pressure and
still maintain a trap seal of at least 1".
Figure 12.2.1 - B
TRAP SEAL REDUCTION FROM 1" POSITIVE PRESSURE
12.3 VENTING OF DRAINAGE STACKS
12.3.1 Stack Vents and Vent Stacks

a. A vent stack shall be provided for drainage stacks having five or more branch intervals.
b. Where drainage stacks have five or more branch intervals, the vent stack shall connect to the drainage
stack as a relief vent, either:
1. To the drainage stack at or below the lowest fixture branch or,
2. To the building drain within 10 pipe diameters downstream from the base ofthe stack.
c. Vent stacks shall also be permitted to be provided for drainage stacks having less than five branch
intervals.
See Figure 12.3.1

I
,I
.J:~TR .JI~TR
I
I - l...
I
-- Tr STACKVENT
1-'
-- l-J~I
1st BRANCH I I I I
1~I.f3E~~~tH : STACK VENT
INTERVAL ~-~
I I I
I I
2ndBRANCH
-- I
I
2ndBRANCH
-- I
I
INTERVAL INTERVAL
~--I ---1
I I
:
I
/ VENTSTACK : / VENTSTACK
I
3rdBRANCH
-- I 3rdBRANCH
--
INTERVAL
,
I
I
INTERVAL - JI
I
I
I I
I I
4thBRANCH
-- I 4thBRANCH
-- I
INTERVAL I INTERVAL I
1
I
--, I
I I
I I
I I
5thBRANCH
-- I 5thBRANCH
-- I
INTERVAL I INTERVAL I
I I
I I
I I
I I
I I
I I
I
RELIEF VENT CONNECTION I) I
PER SECTION 12.13.1.b (1) --...... I
RELIEFVENTCONNECTION I
BUILDING DRAIN
PER SECTION 12.3.1 (2)
\ r-- _J
I
'- 1
BUILDING DRAIN "0"
WITHIN 10 X "0"
PIPE SIZE
RELIEF CONNECTION RELIEF CONNECTION

TO STACK TO BUILDING DRAIN
Figure 12.3.1
VENT STACKS FOR DRAINAGE STACKS
HAVING 5 OR MORE BRANCH INTERVALS
12.3.2 Relief Vents for Stacks Having Ten or More Branch Intervals
a. Where drainage stacks have ten or more branch intervals, a relief vent shall be provided for each ten
intervals, starting at the top of the stack.
b. The lower end of each relief vent shall connect to the drainage stack as a yoke vent below its tenth
branch interval.
c. The upper end of the relief vent shall connect to the vent stack at an elevation not less than 3 feet
above the floor level served by the branch interval.
See Figure 12.3.2

1st BRANCH
INTERVAL
2nd BRANCH
INTERVAL
3rd BRANCH
INTERVAL
4th BRANCH
INTERVAL
5th BRANCH
INTERVAL
6th BRANCH
INTERVAL
SOIL VENT
STACK STACK
7th BRANCH
INTERVAL
r
)-
8th BRANCH
INTERVAL (
I
/ I
I
I 3'MIN
t
9th BRANCH
I I
INTERVAL I I
I I
6th FLOOR I I
10th BRANCH
INTERVAL
I-r
I I
) I
11th BRANCH I
INTERVAL I
I
12th BRANCH I
INTERVAL I
I
13th BRANCH 1
INTERVAL
14th BRANCH
INTERVAL
15th BRANCH
INTERVAL
NOTES:
1. A branch interval is the vertical distance between branch connections to a soil or waste stack,
generally a story height, but never less than 8 feet. The stack has 15 branch intervals.
2. A relief vent is required for the upper ten branch intervals.
3. The relief vent connects as a yoke vent below the 6th Floor branch drain connection and connects
to the vent stack at least 3 feet above the floor on the 6th Floor.
4. The 3-foot vertical rise in the yoke vent keeps pressure surges in the soil or waste stack from
causing spill-over of drainage into the vent stack.
5. Stack relief vents must be the same size as the vent stack. See Section 12.16.4 for sizing vent
stacks.
Figure 12.3.2
RELIEF VENTS FOR DRAINAGE STACKS
HAVING TEN OR MORE BRANCH INTERVALS

12.3.3 Horizontal Offsets in Stacks Having Ten or More Branch Intervals
a. Horizontal offsets in stacks having ten or more branch intervals discharging above the offset shall be
vented either:
1. by considering the stack as two separate stacks, above and below the offset, and venting each
separately.
2. by providing a yoke vent from the drainage stack below the offset to the vent stack not less than 3
feet above the offset.
b. This relief vent installed may be a stack vent for the lower portion of the drainage stack.
See Figures 12.3.3-A and -B
V.T.R. I
ROOF
~
---t-,
1 1
LJ
TYPICAL FLOOR
VENT
STACK
TYPICAL FLOOR
RELIEF VENT FOR I
~
- - -" - -
1
1 I
LOWERPORTION
OFSTACK
1
1
RELIEF VENT FOR

UPPER PORTION
OF STACK
1-
1
VENT
STACK
~)
AL TERNA TE RELIEF VENT
CONNECTED BELOW OFFSET
1
1
~ VENT STACK CONNECTION (Note 3)
~AL TERNA TE VENT STACK CONNECTION (Note 3)

NOTES:
1. The vent stack must be sized for the entire DFU load on the drain stack per Table 12.16.4.
2. The relief vents for the upper and lower portions of the drain stack are requiredto relief backpressure
from the hydraulic effect of the offset. The relief vents must be the same size as the vent stack.
3. The vent stack must connect to the base of the drainage stack, either below the lowest branch
connection above the base of the stack or within 10 pipe diameters downstream from the base of the
stack.
Figure 12.3.3 -A
RELIEF VENTS FOR HORIZONTAL OFFSETS IN DRAINAGE STACKS
HAVING ONE VENT STACK

V.T.R. I
ROOF .JIL
---to
I I
VENT STACK FOR

UPPER PORTION
OF STACK
TYPICAL FLOOR
TYPICAL FLOOR ROOF I V TR

I
I ~L . . .
I
~ (Note5)- TyRELIEF
I I VENT (Nol, 4)
I
1-
I
VENTSTACK
LOWER PORTION
FOR
:-1)
OF STACK ALTERNATE RELIEF VENT
CONNECTED BELOW OFFSET
I
I
V VENT STACK CONNECTION (Note 5)
--I
"'-ALTERNATE VENT STACK CONNECTION (Note 5)
NOTES:
1. The drain stack has separate vent stacks for the upper and lower portions of the stack.
2. The vent stack for the upper portion of the drain stack can be sized for only the DFU load on the
upper portion of the stack. Only vents for upper floor fixtures can be connected to the upper vent
stack.
3. The lower portion of the drain stack carries the DFU load of the upper and lower portions of the
stack. Its vent stack must be sized for the entire DFU load on the drain stack.
4. The relief vent for the lower portion of the drain stack must be the same size as the vent stack for
the lower portion of the stack.
5. The vent stacks must connect to the base of each drainage stack, either below the lowest branch
connection above the base of the stack or within 10 pipe diameters downstream from the base of the
stack.
Figure 12.3.3 - B
RELIEF VENTS FOR HORIZONTAL OFFSETS IN DRAINAGE STACKS
HAVING TWO VENT STACKS

12.3.4 Vent Headers
Vents may be connected into a common header at the top of one or more stacks and then be extended to the
open air at one point.
12.3.5 Other Use Prohibited

The plumbing vent system shall not be used for purposes other than venting of the plumbing system.
12.4 VENT TERMINALS
12.4.1 Extension Above Roofs

Vent pipes shall terminate not less than 6 inches above the roof, measured from the highest point where the
vent intersects the roof.
EXCEPTION: Where a roof is used for any purpose other than weather protection, vents shall extend at
least 7 feet above the roof and shall be properly supported. See Figure 12.4.1
SEALED AGAINST LEAKAGE
~ilN I SECTION 4.5, 12.4.2
NOTES:
1. Referto Section 12.5for provisions to preventfrost closure.
Figure 12.4.1
VENT EXTENSIONS THROUGH THE ROOF
12.4.2 Waterproof Flashings

Vent terminals shall be made watertight with the roof by proper flashing.
12.4.3 Flag Poling Prohibited

Vent terminals shall not be used for the purpose of flag poling, TV aerials, or similar purposes.
12.4.4 Location of Vent Terminal

a. Vent terminals shall not be located where vapors can enter the building.
b. No vent terminal shall be located directly beneath any door, window, or other ventilating opening ofa
building or of another building, nor shall any such vent terminal be within 10 feet horizontally of such opening
unless it is at least 2 feet above the top of such opening.
c. Where a vent terminal is within 10 feet horizontally and less than 2 feet above a ventilation opening
described in Section 12.4.4b and the line-of-sight from the vent terminal to the ventilation opening is inter-
rupted by the continuous ridge of a roof, the ridge shall be at least 2 feet above the top of the opening. Other-
wise, the vent terminal shall comply with Section 12.4.4b.
d. Where a vent terminal is within 10 feet horizontally and less than 2 feet above a ventilation opening
described in Section 12.4.4b and the line of sight from the vent terminal to such ventilation opening is inter-
rupted by a solid wall or solid barrier, the top of the wall or barrier shall be at least 2 feet above the top of the
ventilation opening and the shortest travel distance around the wall or barrier from the vent terminal to the
nearest edge of the ventilation opening shall be at least 10 feet. Otherwise, the vent terminal shall comply
with Section 12.4.4b.
See Figure 12.4.4
I~I' ~~~O~-
WINDOW
!i~
AIR INTAKE OR
EXHAUST OPENING
NOTES:
1. The separation of vent terminals from doors, windows, and air intake and exhaust openings keeps
foul odors from entering the building.
2. The vent terminal is less than 2 feet above the window, but the window is 10 feet or more from the
vent terminal horizontally.
3. The air intake or exhaust opening can be within 10 feet horizontally from the vent terminal ifthe vent
terminal is 2 feet or more above the top of the opening.
Figure 12.4.4
ALLOWABLE LOCA nONS FOR VENT TERMINALS
12.4.5 Extensions Through Wall

Vent terminals extending through a wall, when approved by the Authority Having Jurisdiction, shall be at least
10 feet horizontally from any lot line and terminate downward. They shall be effectively screened and shall

meet the requirements of Section 12.4.4 above. Vent terminals shall not terminate under the overhang of
a building.
12.4.6 Extensions Outside Building

No soil, waste, or vent pipe extension shall be installed on the outside of a wall of any new building, but
shall be carried up inside the building
EXCEPTION: In those localities where the outdoor temperature does not drop below 32P, the Authority
Having Jurisdiction may approve the installation outside the building.
12.5 FROST CLOSURE

Where frost closure is likely to occur, each vent extension through a roof shall be at least 3" pipe size. When it
is found necessary to increase the size of the vent extension to meet this requirement, the change in size shall
be made inside the building at least one foot below the roof with a fitting acceptable to the Authority Having
Jurisdiction. See Figure 12.5
, ~ MINIMUM3 INCHSIZE
SEALED .lL:.
WATERPROOF
t
FLASHING ~ 6" MINIMUM
/ ROOF
1"'--- INCREASER FITTING

WHERE NECESSARY
- VENT SIZE PER TABLE 12.16.6.A
NOTE:
1. Where pipe size increases are necessaryto avoid frost closure, the increase in pipe size must
be one foot below an area subject to freezing temperatures.
Figure 12.5
MINIMUM VENT EXTENSION SIZE TO PREVENT FROST CLOSURE
12.6 VENT SLOPES AND CONNECTIONS
12.6.1 Vent Slope

Vent and branch vent pipes shall be free from drops and sags and be sloped and connected as to drain by
gravity to the drainage system. See Figure 12.6.1

VENT MUSTN
0T T
FORMA TRAP I
I
BEAM
T r--- 7 :
r
I - ---"1
I
I :
I
II
--1:r-- 7J I
II
t
I~ I I
~
r BACKWARD SLOPE
t FORWARD SLOPE
r
NOTE:
1. Vent piping that is sloped allows condensation and moisture that may form in the piping to drain to
the drainage system.
2. Vent piping must not have any trapped sections. Water may collect in trapped piping, fill the piping,
and renderthe vent ineffective.
3. Vent piping can slope back to the fixture served or forward away from the fixture, as long as it drains
to the drainage system.
Figure 12.6.1
VENT PIPING SLOPE
12.6.2 Vertical Rise

Every vent shall rise vertically to a minimum of 6 inches above the flood level of the rim of the fixture being
served before connecting to a vent.
EXCEPTION:
If a horizontal offset is required in the verticle rise due to existing conditions the horizontal section shall be
installed in accordance with sec. 12.6.2.2.
I
CONNECT VENT TO I
/ SOIL OR WASTE PIPING

ABOVE CENTERLINE
I
I
I
I
HORIZONTAL )
CENTERLINEOF THE /"
SOIL OR WASTEPIPE /"
/"
/"
/"
I
/
LRIZONTAL DRAIN
MUST BE ABOVE
CENTER LINE
NOTES:
1. Connecting the vent above the centerline of a horizontal drain reduces the possibility of the vent
connection being fouled by the flow in the drain.
Figure 12.6.2 - A
VENT PIPE CONNECTIONS TO HORIZONTAL DRAINS

FLOOD LEVEL RIM OF LAVATORY
I 1 SEE EXCEPTION TO
i
;;r
- - - - -6" MIN- -:-1 SECTION12.6.2(NOTE2)
STACK VENT .. II t I II
I LAVATORY l.-'-, I BATHTUB
W.C. r- -1
~ TRAP ARM
(NOTE 1)
NOTES:
1. A separate vent will be requiredfor the bathtub if the developed length of its trap arm exceeds the
maximum allowable length in Table 12.8.1.
2. If a vent is required for the bathtub, it can have a horizontal offset below the flood level rim of the
bathtub, but it must be 6 inches above the flood level rim of the lavatory before it connects to another
vent. The horizontal offset below the flood level rim must be sloped so that it drains to the drainage
system.
Figure 12.6.2 - B
HORIZONT AL VENT PIPING
BELOW THE FLOOD LEVEL RIM OF FIXTURES
12.6.2.1
Where vent pipes connect to a horizontal soil or waste pipe, and conditions require a horizontal offset in
the vertical rise below the flood level rim, the vent shall be taken off so that the invert of the vent pipe
is at or above the centerline of the horizontal soil or waste pipe and ahead of the trap and fixture
connection that it serves.
12.6.2.2
The portion of the horizontal vent installed below the flood level rim as permitted in Section 12.6.2.1
shall be installed with the required slope. See Figure 12.6.2 - B
12.6.3 Vent Connection Height Above Fixtures

Connections between any horizontal vent pipe, including individual vents, branch vents, reliefvents, circuit
vents or loop vents, and a vent stack or stack vent shall be made at least 6 inches above the flood level rim of
the highest fixture on the floor level.
12.6.4 Side-Inlet Closet Bends

a. Side-inlet closet bends shall be permitted only in cases where the fixture connection thereto is vented.
b. In no case shall the side-inlet be used to vent a bathroom group without being washed by a fixture.
EXCEPTION: As allowed in Sections 12.10 and 12.11.
12.7 ADJACENT FIXTURES

Two fixtures set adjacent within the distance allowed between a trap and its vent, may be served with one continu-

ous soil or waste-vent pipe, provided that each fixture connects separately into an approved double fitting having
inlet openings at the same level. (See Section 12.9.2 for inlet openings at different levels.) See Figure 12.7
Comment: Suitable doublefittings for connecting adjacentfixtures such as lavatories, sinks, tubs, showers,
urinals, orfloor-outlet water closets to a stack are double sanitary tees, double fIXture fittings (plastic), and
sanitary crosses. These fittings have high branch openings intothe stack that keep the top of the vent opening
above the weir of the traps to prevent self-sip honage.
I
I
I
I
I~ COMMON VENT
I
I
~ SANITARY CROSS OR
DOUBLE SANITARYTEE
Figure 12.7
VENTING ADJACENT FIXTURES
CONNECTED TO A VERTICAL DRAIN AT THE SAME LEVEL
Table 12.8.1
MAXIMUM LENGTH OF TRAP ARM
Diameter of Trap Length-Trap to Vent Slope-Inches per Foot
Arm (Inches)
11/, 3'6" 1/,
1112 5' 1/4
2 8' 1/4
3 10' 1/4
4 12' 1/8
NOTE: This table has been expanded in the "length" requirements to reflect expanded application of the wet venting principles. Slope shall not
exceed 1/4" per foot.

12.8 FIXTURE VENTS
12.8.1 Venting of Fixture Drains

Fixture drains shall have a vent so located that the vent connects above the top weir of the trap and the
developed length of the trap arm is within the limits set forth in Table 12.8.1.
EXCEPTIONS:
(1) Water closets and similar siphonic fixtures.
(2) Combination waste and vent systems. (see Section 12.17)
(3) Vents may be connected below the top weir of the fixture trap if the following conditions are met:
a) The vertical section of the drain pipe shall be at least one pipe size larger than the trap inlet size.
b) The horizontal pipe connected to the trap outlet shall be at least two pipe diameters long.
c) The developed length of the trap arm shall not exceed the values in Table 12.8.l.
-- VENT
DISTANCE FROM
I
--- TRAP TO VENT INSIDE WALL OF PIPE
TOP OF VENT OPENING
\ L-
LTRAP
TRAP ARM
WEIR
- WASTE
NOTES:
1. Trap arm lengths are limited by Table 12.8.1to prevent self-siphonage of the fixture trap.
2. The top of the opening at the vent pipe must not be below the elevation of the trap weir. The
maximum trap arm lengths in Table 12.8.1 are based on using sanitary tees or other short turn
fittings to connect trap arms to the drainage system. Long turn fittings should not be used with
Table 12.8.1.
3. The trap arm length is the developed length along its centerline, including any changes in direction.
Figure 12.8.1 - A
THE MAXIMUM LENGTH OF TRAP ARMS

VENT
I
I
I
r"A"
I
I
I VENT
I r-"A"
VENT I
~~ I
E I
CONNECT I I
D I W
ABOVE TOP : r "-

""
""
:'~~O.c~ Kv -"C"
I ~.B.
NORMAL VENT EXAMPLE OF EXAMPLE OF
CONNECTION EXCEPTION #3 EXCEPTION #3
NOTES:
1. "A" is the trap pipe size.
2, "B" is the horizontal pipe between the trap outlet and the vertical leg. Its length must be at least
two times the trap pipe size to avoid creating an "S" trap.
3. "C" is the vertical drop. It must be one size larger than the trap pipe size.
4. "0" is the connection to a vented drain line. The horizontal portion of "0" must be the same size as
"C". The distance from the weir of the trap to the vent connection at "0" must be within the limits of
Table 12.8.1, based on the size of the trap.
Figure 12.8.1 - B
EXAMPLES OF EXCEPTION #3 TO SECTION 12.8.1
(VENT CONNECTIONS BELOW THE WEIR OF A TRAP)
12.8.2 Provision for Venting Future Fixtures

On new construction of residential dwelling units with basements, a 2" minimum size vent shall be installed
between the basement and attic or tied into an existing, properly sized vent and capped for future use.
12.8.3 Crown Venting Limitation

A vent shallnot be installedwithintwo pipe diametersof the trap weir. SeeFigure 12.8.3
VENT---- NOT LESS

THAN 2 X "D"
INSIDEWALLOF PIPE
WASTE -
NOTES:
1. Vents connected too close to the crown or weir of a trap are subject to clogging, thereby rendering
the vent ineffective. Vent connections must be at least two pipe diameters from the weir of the trap.
Figure 12.8.3
CROWN VENTS ARE PROHIBITED
282 2003 National Standard Pumbing Code-lIIustrated

12.8.4Water Closets and Other Siphonic Fixtures
For water closets and other fixtures that operate by siphonic action, the distance between the outlet of the
fixture and its vent connection shall not exceed 3 feet vertically and 9 feet horizontally.
12.9 COMMON VENTS
12.9.1 Individual Vent as Common Vent

An individual vent, installed vertically, may be used as a common vent for two fixture traps when both fixture
drains connect with a vertical drain at the same level.
12.9.2 Fixtures Drains Connected at Different Levels
A common vent may be used for two fixtures installed on the same floor but connecting to a vertical drain at
different levels, provided that the vertical drain is one pipe size larger than the upper fixture drain but in no
case smaller than the lower fixture drain. See Figure 12.9.2
i
1 DFU FIXTURE 3DFU I
T
:r COMMONVENT
:/
I
COMMON VENT
I 2" I
1 DFU FIXTURE .1 1DFU
3" (NOTE 1)----------
NOT LESSTHAN 1 1/2" ~ 11/4" 3"~
T
1 DFU I
:/
I
COMMONVENT
I 3DFU
2"
2"(NOTE1)~
2"
NOTES:
1. When the upper fixture is 3 DFU and the lower is 1 DFU, the vertical drain must be 3" instead of 2"
so that the 1 DFU fixture is wet vented during the heavier discharge from the 3 DFU fixture.
Figure 12.9.2
VENTING FIXTURES CONNECTED TO A
VERTICAL DRAIN AT DIFFERENT LEVELS
12.10 WET VENTING
12.10.1 Single Bathroom Groups

a. An individually vented lavatory in a single bathroom group shall be permitted to serve as a wet vent for
either the water closet, the bathtub or shower stall, the water closet and bathtub/shower if all of the following
conditions are met.
1. The wet vent is 1-1/2" minimum pipe size if the water closet bend is 3" size or it shall be 2" minimum
pipe size if the water closet bend is 4" pipe size.
2. A horizontal branch drain serving both the lavatory and the bathtub or shower stall is 2" minimum pipe
SIze.
3. The length of the trap anTIfor the bathtub or shower stall is within the limits of Table 12.8.1. If not, the

'bafutIibm5howr:5ta1l:s11a11 k IDilivic1rrn11y'V;enred.
4. The ..di:tanre frmn the -oDflet .of1fue WlUer L:1l0:Set
10 be L:CIIIIWd1.on,of;the"Wcl'Vent is within ;fhe limits
estab.Eheil by 'Sectiilll12.:8A.. {)berwise, ;fhew.a:Ier ,clnset:Slnill 'he iiniJividruIDy'V;entOO.
5. A ;horizontal :bIanib :Serving 1he 1av21nry .and be :hafbtu'b ,m :Shower Elan $lm'll.cOIlIle!:t:to be :5!.aCk:at;the
:same lev.el.m; ifbe 'W-B1er.closet, ({ITiit:llllIY.cil111ltJct!:tobe WlUer idoset 'bend., lOTthe Jav..a1nry ,and :bafutnb Dr
'ShowT::51IDlIITIl'!Yindiv'iduaIlYL:01IllfX110 ibe w21er ;closet :bend.
6. When be b.atmDomgrSllp ,is ifbe 10pmOBt JmwDn:a:StaCk, :allOrizmrta1 ImanCb :scrv'IDg the illv:atnry;mill
be fuafutnb Dr :Blwwer1illl may..cmmect to tbe 'Starik bellow:the WlUer .c10:Set:benii, \Dr'the illv:atory :ani] 1he
lhafulIIib \Dr~:stan:may UnifiviilmiIJy .cill1lIf:D1:toifbe$1arlkklow1he'W1l1er ;Closet :Dena.
Se.e ~.es Rft.tUl-)i. 1t'hrr<DDgb-C c'1
/1
""1 ~1112"
"",- 1/
l' -_/ 1
1 / I
,j,..."" 1114,,---1
I /11/2"
,;, "TJJBISHDWER
"
Q
STATIK_i
VENT I
1 f
1 ' ,
I,J'.....
-2",'MltN :a~D"'
:5~D"' 1F;2"
1F11f2"
WA"liER:cLDSET
,WiTEB:
11. Ti1e'XIBTltl'orihe ibathIDDm f91D!Wiis 11-~12", ,which ;isl112.1hE;:;iLeDT:thE3" :drainfur1helbathwom
gID1Ip.
~Jl1T..e 12.11.10..11- A
A WET VJENTED BA."'ODlOOMGR01UP 'WITII.A3 II {Lfi5E'lf BEND
:S!lNGLESI'ORY OR -roF FLOOR;)
TJJBtBfIDWER
I
J
iI.l.1VX\lrRl~
W1TIES:
11, '!;1ffi:;MerttffrrrtthE iba:fu1iIDDm~ iis2" ,',Whi:dt1iis l1~tthE $~ a1ftthedJ"'draim mr1hetbB:U lIDDm~]i),
[email protected]!Jmw:rulf)~hti ttreMe!tIBd !a 3" [irairwwit!:1:a ~'l !2"'XIBn:( ins1allimg ';a 1-112"'vBnt
Dmtthe-4" W ilil\IIIfIDUIrJ(caJ.SEUlI111!ilBl;f$~!W ccmffllfSmm ffIDrtthEiirs1BIlBr!aT\a iinspBI::tm:,
JF~ n.BIIl.I - B
A~ ,,~ JEAlIUIWQXO));IGROUP WJI'DDA 4'" tLOSIET BE~'D
(~ Sft))]lUf OR 1IOJPFL:OOJl\)
.284 J}(j{J3'Notimuil 'fitanjjm:o PumbingL{){i-Ill Ll.lStI'.aEELj

I /~
I // I
I // I
I /// I 1 112"
I
I
//
III
//
//
1 1/4"
I
(/ ~ I
VENT i LAVATORY ~ 5'-0" MAX IF 1 1/2"

8'-0" MAX IF 2"
WATER CLOSET
Figure 12.10.1 -C
A WET VENTED BATHROOM GROUP WITH 3" OR 4" CLOSET BEND
(SINGLE STORY OR TOP FLOOR)
12.10.2 Double Bathtubs and Lavatories

Two lavatories and two bathtubs or showers back-to-back may be installed on the same horizontal branch
with a common vent for the lavatories and with no back vent for the bathtubs or shower stalls provided the
wet vent is 2" in size and the lengths ofthe tub/shower drains conform to Table 12.8.1. See Figure 12.10.2
LAVATORY
WATER CLOSET
Figure 12.10.2
WET VENTED BACK- TO-BACK BATHROOM GROUPS
(SINGLE STORY OR TOP FLOOR)

12.10.3 Multi-Story Bathroom Groups
a. On the lower floors of a stack, the waste pipe from one or two lavatories may be used as a wet vent for
one or two bathtubs or showers as provided in Section 12.10.2.
b. Each water closet below the top floor shall be individually back vented.
Exception: The water closets in bathroom groups shall not be required to be back vented if the following
conditions are met:
1. The 2" waste serving the tubs/showers and lavatories connect directly into the water closet bend with
a 45 wye tap in the direction of flow or,
2. A special stack fitting is used which consists of a 3" or 4" closet opening and two side inlets each 2"
in size and the inverts of which are above the center, and below the top of the water closet opening; and one
of the 2" inlets is connected to the tub/shower drains, and the other is connected to the waste pipe from a
maximum of two lavatories which are vented to a vent stack or stack vent; or,
3. In lieu of the special stack fitting of Section 12.10.3b(2) above, 4" closet bends with two 2" wye taps
may be used.
See Figures 12.10.3-A through-E
INDIVIDUAL
BACK VENTS
TUB/SHOWER
TUB/SHOWER
WATER CLOSET
WATER CLOSET
SOllSTACK~
Figure 12.10.3 -A
WET VENTED BACK- TO-BACK BATHROOM GROUPS ON A LOWER FLOOR
WITH BACK VENTED WATER CLOSETS
(ONE ARRANGEMENT)
286 2003 Nationa/ Standard Pumbing Code-Illustrated

r
I
VENT -/
/1
:
I
// I
// I
/ I
// I
/ " I
/
/~
I
//~
// 2
:
I
I~
I
~
VENT
STACK
// I I
'" /// lAVATO
/ I I
///: I
:
INDIVIDUAL
BACK VENTS I
I
/
I('-',
'- /
(
I '>
I
1
I
/ ~ RY I
I
I
lAVATORY
TUB/SHOWER
TUB/SHOWER
!
I
I
I
I
I
I
I
WATER I
CLOSET I
I
I
I
I
I
I
WATER
CLOSET
SOil STACK~I
Figure 12.10.3 - B
WET VENTED BACK-TO-BACK BATHROOM GROUPS ON A LOWER FLOOR
WITH BACK VENTED WATER CLOSETS
(ANOTHER ARRANGEMENT)
I'
I
I
/I
/" I
/" I
2" r-- " /"./ 2" VENT

T ~
'<v i~
:
STACK
LAVATORYj TUB/ :i I
SHOWER I i
I TUB/
I SHOWER
WATER
CLOSET
3"OR4"
CLOSET BEND
NOTES:
1. Thisis an exampleof Exception#1 to Section12.10.3.
2. Two adjacent bathroomgroups are shown but individual bathroomgroups can also bewet vented in
this manner.
3. A lower floor is shown, but the arrangement can be used at the top of a stack.
Figure 12.10.3 - C
ADJACENT BATHROOM GROUPS WET VENTED WITH 45 DEGREE WYE TAPS
2003 National Standard Pumbing Code~lllustrated 287

2" T
"-),
(I / VENTSTACK
11/
1);,"-1 :
I
I
~
/MAX
8'-0"
2"
~ pj~?t
3"OR4"
CLOSET BEND
DETAIL OF
HUBLESS
SPECIAL
1Y:i'X~ "- STACK FITTING
2" TRAP----
TUB \ SHOWER
NOTES:
1. This is an example of Exception #2 to Section 12.10.3.
2. The side inlets to the special stack fitting are slightly higher than the water closet connection and
the side connection that is wet vented vents all of the fixtures that are connected to the fitting.
3. A lower floor is shown, but the special stack fitting can be used at the top of a stack.
Figure 12.10.3 -D
A BATHROOM GROUP WET VENTED WITH A SPECIAL STACK FITTING
r
I
/-1
2"~ ", / / I
" II ,/ '< I
I ------VENT STACK
1);,"
\ I,
.. 2'"
',I
'I
I
"- , 1X" ,
", ~ ,
-l
LAV
TUB/ SHOWER
1)-2"X 2"
TUB/ SHOWER
1)-2"X 2"
NOTES:
1. This is an example of Exception #3 to Section 12.10.3.
2. The oversized 4" water closet fixture drain permits the tub/shower on one side of the drain to be wet
vented by the lavatory on the other side of the drain.
3. Two adjacent bathroom groups are shown, but individual bathroomgroups can be wet vented in this
manner.
4. A lower floor is shown, but the arrangement can be used at the top of a stack.
Figure 12.10.3-E
ADJACENT BATHROOM GROUPS WET VENTED WITH 4" CLOSET BENDS
HAVINGTWO 2" WYE TAPS

n.118.4 BadUubsm:tdW:a:rerO~
.An mrn~-w:tm1:eil :batb:tlibUnal$Iqgre !b.atbrlOflIIl@"\IDW$illill1:be
:pcrm1tteil1i0~f:m; at,~w.ent ffmi11l;e
warer .doset jf:.au IOfi11l;effb'lliJWing iOODilitiDIl zareIIIlft:
11. Tlre wct~ ii 2" urii:n'mmm :5J;ze.
b. Tlre.dffitance from ::fl1;e\OlI1i1;e:t
<IDfIfb;e'W.aIer clBRet ttIDcfu;e<CIDnnecfum (flf:th;e wet w.ent iffiw1fuin 1h;e :limits
~JiShedfuy Sfdion 12.'RA. IQ):themi.H;e,
rnh;ewwter~1IDret$mm!heiiniIiviilimJ1.ywfD1ed.
See ~ 12.116..4
'.xTENT
.I . ~ 11~"q:DR:B"'(lli.'TISET'BENDtDR~1\lC*I
:// Z'ffDR4"CCl.DSET33ENDtDRiBRA1\lC*I
'I
1 '17HB'/5fIDWR
Ii I
11
SDLLDR " 1 l'~ ;1~"$.2""'fRAf'
W1\fITE ""'"""~1< ---Ii
~,~ . I
i.
,
~ \W~CCl.DSET
(NOTtE1)
5DLLETAr:f< 11
3"tDR4"
.'NOTES:
1. lHheTTlEKimum \!iIi5:ta1:me
'fmm tt!1e'W:Ei1endlJDse:t([).Uf1e:t B1fue11iID1;izID1rtta
ttID!itswern {CDT1'Ii1ectirmis 1:anD.B
ff'ee:tuertica I.
;2. IT+.
ilDwerIT"IODT
iis$tmwm, buttthe arran.gement IDBt1De JJSBrlH.tttqp iDfstadk.
~.e 112.111,.4
A WATERCLOSEJ' WET VENifEDiBY A !BA~
12.11l.5 W:asreStacbmDw.e~'nDm
!In :a:mn.gk iiwiJ1iiQg amit, :a 'WBSte:StaCk.'WJiidl !Recew.e.s:th;eiii.--~hare <DfalkitC.hm1 '~$llik (or:a.3 <ililltfu.ctur"e
:mayalsID $fTVf:m;:a iwet wtmt 1IDT:alla:un&:y ~ lOT11.3,iifu tliixture -cmmecterlitID :thf $1adk:at:.the tEl.0or1bclIDW..
Tbf :m11Timnm.size iofrthe W.asIe 'Bf.aCkamo'WEt~ JI.!P110tthe :~ itmrnrih -cmme.cJiion:Shilll !:be':2" :in ld:iameter.
No $llik $luill :he 1insta!llerlOD 111w!'Hiru:b.'Wet WfI1t:that wtmt5 Jl w21crrJlo.set. :See FJi,gIllJr.en.lll1.5
2(1()3 Nationn/ Standar..dPumbingod.e-Jllustr.atd 2'89

T /1J-4" MINIMUM
I KITCHEN SINK
I OR OTHER FIXTURE UP TO 3 D.F.U.
(EXCEPT A WATER CLOSET)
~ UPPER FLOOR ~
;2" WET VENT (MIN.)

LAUNDRY TRAY
OR OTHER FIXTURE
(3 D.F.U. MAXIMUM)
~ LOWER FLOOR ~
2"
NOTES:
1. The arrangement is limited to waste stacks in dwelling units, and cannot serve water closets.
Figure 12.10.5
WASTE STACKS IN DWELLING UNITS
12.11 STACK VENTING
12.11.1 FixtureGroups
A single bathroom group and a kitchen sink (with or without a disposer and/or dishwasher) located back-to-
back, or two bathroom groups back-to-back may be installed without individual fixture vents in a one-story
building or on the highest branch of a stack provided that the following conditions are met:
a. Each fixture drain connects independently to the stack.
b. The tub and/or shower and water closet enter the stack at the same level.
c. The requirements of Table 12.8.1 are met.
d. A side inlet connection into a 4" closet bend shall be considered to be an independent connection to the
stack.

1X," LAVATORY
4" CLOSET BEND
TUB / SHOWER
STACK
NOTES:
1. The arrangement shown is permitted in a one-story building or at the top of a stack.
2. Each fixture must connect independently to the stack except that the tub/shower connection to the
4" water closet fixture drain is considered to be a connection to the stack because the 4" drain is
oversized for the water closet.
3. The length of all trap arms from their trap weir to their vent opening at the stack must not exceed
the limits in Table 12.8.1. The vent distance for the water closet must be in accordance with
Section 12.8.4.
4. Bathroom groups without kitchen sinks can also be stack vented as shown.
Figure 12.11.1 - A
STACK VENTING A BATHROOM GROUP AND AN ADJACENT KITCHEN SINK
KITCHEN
SINK
TUB / SHOWER
NOTES:
1. The arrangement shown is permitted in a one-story building or at the top of a stack.
2. Each fixture must connect independently to the stack except that the tub/shower connections to
the 4" water closet fixture drains are considered to be connections to the stack because the 4"
drains are oversized for the water closets.
3. The length of all trap arms from their trap weir to their vent opening at the stack must not exceed
the limits in Table 12.8.1. The vent distance for the water closets must be in accordance with
Section 12.8.4.
4. Bathroom groups without kitchen sinks can also be stack vented as shown.
Figure 12.11.1 - B
STACK VENTING ADJACENT BATHROOM GROUPS AND AN ADJACENT KITCHEN SINK
12.11.2 LowerFloors
Lower floor bathroom groups may be vented as provided in Section 12.11.1,provided the following conditions
are met:
a. A wye is installed in the stack with an upright one-eighth bend continuing from the wye branch to serve
the stack group.
20G3 National Standard Pumbing Code-lllustrated 291

m.A Z' rdief~tm1l is;c.o~ted' to'tfu:~e 1Jn:amdIat fuastr6,iD:cl'res;
af1(jJvetfteff(i}Q(f
feveLrim QftlIe ErigIest
:Eixtnreou the: "'1G::Dmmdh.
See FJgD!IreSEUU-A amI-B
I VENr$1\CK'
:r
r ~ 67M1N<
~
'
,
/"
.- .-
27\AENT 7.Ji ~/
./'. FLaDlD~~
aFHI
\ ;!, IL
r t'k~.. LAVJmJRY
I " :
'i
[
II' '''''-
."-
w.tm=rea.osEr
-. W1Tft4:'RXJUREIJIfmN.
~.
11.. Ead1nfi~iimt:trestack(~musttG<1Il1TllTedti~~ fi:I;ttresub:--sI:at:X~tbattfre
~IIIJectimrn fi:I;ttre4r'''watEJrcii1Iset1fiti!u;e efuaii:nisGEffSider.edJtm;be a crnmectiarn to ttre 5Ir1fi-stack
~11~itti$Cl\(ersiZed;furrtlirewaffircimset.
L liITe lenqttn of all trapJ arms tram ttreirtl1ap1weiirtD>ttrefrstaJ::k1:must not exceed the limits in T abfe
112ffit. lf1ire\tentdiStarTcefuFttrewateJrciOsel:t must be iiT.acoordarrcewith1 S'ectiarr 12.8'.4.-
Jt~ ]12..11:..2
- A
STACK ~ A. ~ GROIIP ON A. LOWER nooR OF A DRAIN srACK
\!l;
TUIIJSjj(JWffi,
FJgIIIIe DUU B -
Sl"ACK ~ AND WET ~ BATIIKCJOM' GR.mlIPS ON A DRAIN SJrACK
~ ZfJO3i Natiarrcdl Stamlhrd,l!UmmirgCi](j:k-'-lIlilstrale:d

12.11.3 Reserved
12.12 FIXTURE REVENTING

Where fixtures other than water closets discharge into a horizontal drain branch downstream from a water
closet, each fixture connecting downstream shall be individually vented.
EXCEPTIONS:
1. Fixtures having a common vent in accordance with Section 12.9.1.
2. Lavatories or sinks on horizontal branches complying with Section 12.12.2.
3. Fixtures connected to a stack above the highest water closet or bathtub in accordance with Section
12.12.3.
4. Fixtures that are permitted to wash down vents in accordance with Section 12.12.4.
5. Fixtures that are battery-vented in accordance with Section 12.13.
6. Fixtures in single dwelling units that are vented in accordance with Section 12.13.5.
12.12.2 HorizontalBranches
Three lavatories or one sink within 8 feet developed length of a main-vented line may be installed on a 2"
horizontal waste branch without reventing, provided the branch is not less than 2 inches in diameter through-
out its length, and provided the wastes are connected into the side of the branch and the branch leads to its
stack connection with a grade of not more than 1/4 inch per foot. See Figure 12.12.2
T
I
I
T 0"'0
I ~~ I
STACKVENT~I R~OV
1
I
~'-O
O~...J.
>'
LAV
I
I,
~ VENT
STACK
I .,0~ I
~",. 2" NOT MORE THAN I
~~
J-4"PER FOOT SLOPE J
//1
LAV / I
/ / :;~~" 1
/~G'0 I
/# '0
/ / ",- 'C _\0" I
/ ~"r' ~\~ I
" / /Oi\"\1'p OR~OV I
\'1- / ~ ~v
/// ~O~...J. SINK I
(~~0 UP TO 3 DFU :
I ~~
I 1
'2"-NOT MORETHAN
J-4"PER FOOT SLOPE
, WYE IN STACK WITH UPRIGHT 18 BEND
NOTES:
1. The horizontal branch must have not more than 8 feet developed length, be 2" minimum size, and
be sloped not more than 1/4" perfoot to avoid self-siphonage of the fixture trap.
Figure 12.12.2
FIXTURES ON HORIZONTAL BRANCHES OF A STACK WITHOUT REVENTS

12.12.3 Fixtures without Revents Above Highest Bathtubs and Water Closets
Fixtures without revents may be connected to a soil or waste stack above the highest water closet or bathtub
connection if all the following conditions are met:
a. The total load does not exceed 3 dfu's.
b. The soil or waste stack is 3" or larger.
c. The total load on the stack is in accordance with Table 11.S.lB.
d. The waste piping of the fixture above the water closet or bathtub connection is in accordance with
Sections 12.8.1 and 12.12.2. I
See Figure 12.12.3
jL
-I-
I
r l
1~"MIN.~I I
I 2" (NOTE1) I
r . LAVATORY:
1 DFU I
I
!-- 3"
4th FLR I
t I 1
I
2" (NOTE 1) I
r
-. SINK
2 DFU
I
I
I
3th FLR
-- 3" I
t I 1
I
BATHROOM
GROUP
2nd FLR
t
- STACK "A"
-3"
t 1st FLR 1
BUILDING DRAIN
NOTES:
1. One or more fixtures totaling up to 3 DFU can be connected to a 3" minimum stack above the
highest bathtub orwater closet without individual vents (revents) if the horizontalwaste branch(s)
from the fixture(s) is 2" size with 8 feet maximum developed length and sloped no more than 1/4" per
foot.
2. The stack must be larger than 3" size if required by Table 11.5.1.8.
Figure 12.12.3
UNVENTED FIXTURES ABOVE THE HIGHEST BATHTUBS AND WATER CLOSETS
"

12.12.4 VentWashdown
Fixtures other than kitchen sinks or food-waste-grinders shall be pennitted to wash down a vertical loop vent,
circuit vent or relief vent associated with a battery-vented horizontal soil or waste branch without reventing,
provided that:
a. Not more than 2 drainage fixture units are drained to a 2" vent, nor more than 4 drainage fixture units are
drained to a 3" vent;
b. The fixture trap ann lengths comply with Section 12.8.1;
c. The fixtures drained to the vent are within the same branch as the other fixtures served by the vent; and
d. No other fixtures are drained to the vent.
12.13 CIRCUIT AND LOOP VENTING
12.13.1 Battery Venting

a. A maximum of eight floor-outlet water closets, showers, bathtubs, or floor drains connected in battery on
a horizontal branch drain shall be pennitted to be battery vented.
EXCEPTION: Blowout type water closets.
b. Each fixture drain shall connect horizontally to the horizontal branch drain being so vented.
c. The horizontal branch drain shall be considered as a vent extending from the most downstream fixture
drain connection to the most upstream fixture drain connection.
d. Back-outlet water closets shall be pennitted to be battery vented provided than no floor-outlet fixtures are
connected to the same horizontal branch drain.
EXCEPTION: Back-outlet blowout type water closets.
e. The battery vent shall be a circuit or loop vent connected to the horizontal branch drain between the two
most upstream fixture drains and shall be installed in accordance with Section 12.6.
f. The entire length of the vent section of the horizontal branch drain shall be unifonnly size for the total
drainage discharge connected thereto.
g. The maximum slope of the horizontal branch drain shall be 1 inch per foot. h. A relief vent shall be
provided on battery-vented horizontal branch drains on lower floors which have four or more water closets
connected.
i. The relief vent shall connect to the horizontal branch drain between the stack and the most downstream
fixture drain connection.
j. Reliefvents shall be installed in accordance with Section 12.6.
k. Circuit, loop, and relief vents shall be permitted to be a fixture drain or fixture branch for fixtures located
within the same branch interval as the battery-vented horizontal branch drain.
EXCEPTION: No more than four drainage fixture units (DFU) shall discharge to the vent. (See Section
12.12.4).
1.Lavatories and similar fixtures shall be pennitted to connect to the horizontal branch drain, either horizon-
tally or vertically.
EXCEPTIONS:
(1) Fixtures that are not located on the same floor as the battery-vented fixtures.
(2) Fixtures that do not have an individual, common, or continuous vent.
m. Batteries of more than eight battery-vented fixtures shall have a circuit or loop vent for each group of
eight or less fixtures.
n. Where there are two or more groups of battery-vented fixtures, the horizontal branch drain for each
downstream group shall be sized for the total discharge into that group, including all upstream groups and the
fixtures within the group being sized.
See Figure 12.13.1 and the definitions of "Battery of Fixtures, "Vent, Circuit, and "Vent, Loop.

RELIEF
VENT
RELIEF
VENT
BACK OUTLET FIXTURE
RELIEF VENT
NOT REQUIRED
RELIEF VENT
NOT REQUIRED
NOTES:
1. Battery vented horizontal branch drains can serve a mixture of two to eight water closets, floor
drains, bathtubs, shower stalls, and other floor-outlet fixtures.
2. Battery vented fixtures must connect horizontallyto the horizontal branch drain.
3. The entire length of the horizontal branch drain must be sized for the total DFU load for the branch.
The slope of the drain must not exceed 1" per foot.
4. The developed length of fixture trap arms must be within the limits of Table 12.8.1 for the given pipe
size.
5. Lavatories, sinks, and wall-mounted urinals can connect horizontally or vertically to the horizontal
branch drain, but they must be independently vented.
6. Reliefvents are requiredwhere horizontal branchdrains on lowerfloors serve more than four water
closets.
7. Fixtures are permitted to drain into circuit, loop and relief vents. A 2" vent can drain 2 DFU. A 3"
vent can drain 4 DFU.
8. Back outlet water closets and wall mounted urinals that are battery vented must connect horizon-
tally to the horizontal drain branch.
Figure 12.13.1
CIRCUIT AND LOOP VENTING BATTERIES OF FIXTURES

12..t3.2 Dmrl!Bnnmes
a.. W1'remdual' paraIreL IIoriZorrtat fu:anches; seJ1Vea;total: af eigfrtr water clasets; (ranr 0111eadt fu:ancl:t)" eacfL
brand]; sIra:EI!ae provided! wiitl'I'a cit'crritr or roO]! vent at!:a;p1.'Jfut.J:retwee:mtlie two waten closets most clistarrt::fi:mn
the goi! stacK:...
0.. WIrere mtuI;es; suclL as Yavat01;ies;dIScliarge futo) a. ffimTIbrandr,. eaclL Sllctt fixt:nre shall ae: vented'.
1z..t33 VemtCcmnediollS
Cmcuit;. [Q'Q];1;.
and reI:idfvent C"@nnecrrQIIS;to'Erat:teny-ven:t.troJII6mii&ontaEdbriit bmncl.Ies ~IT De talten- offf at!:a1
verticaL angfu or firann tfte t61p or tIle homontaII di:aH;n. see Sectiom U..6\.!
12..1i3A r~BacK--tn,...BadimBatt9y
Wfrern~ are amrrected. ta>one: fumU:<OltIfa:Il
fuarrcl:1n
tlmmgm at~ wl'e QFa: ~.. tee ima;veuticaf
~. atCQInmOlI!ventt fem-ead'IltwO' ~ ~~cK.. w<f<rufrl'ecmmediGl11! sfi:a:IJCDe:J?17OVIcfurl...
The
:G!mllI6mJvent sfurl] De ~ ii:n3iveut:maBpt;ISitiiGIIT
<I$alC'01I1:iinratiomGJiftIle:a'cmftft:<roJ:IIIect1(crm~ F'~
12...13.41
Jl2.US ~Dwd&mgtInift
1ImatWgrt:dlweJJringunittcrmat1TII~li.rn:Jj~'~~~dIiafu1an-~clIrafu,.fi%tLU;e:m:a.l"D-e:
~wif:fumtt~iiifim]]vG:II1i$nmt~ta{]lillw,fug:~:
II..~requ~dS"ediOm 11281..11
aml11fanre 112$..11
areme1t.
2. w~ wv~ ~ are c~uFawJ.IStreaml fiiWmDtI1eIJI!:'Istnp&t:iJ::eaI:m
~ OUitIle:~
1Jmamrfn andlrremuean-afte:Jrtl'rem:Qstd'~~.
3..1TI1:eveIlt$orv~ ~~. k~ s:en:vq um;re:n-
JbdS: p.tiQviifed!tliatttfte ~ Gllftfte~ G:am
am::~tfteOOtaiJ fffiJmmemi1t~qID]RIJJ))~.
4t The: ven:ts;sfuElill
o-e:Lmrt!.
~ 1fuan2 iindres irn~wErem alwateJr~ is;~erlJ t'@tEre~ntaiJ
lmmcfummQIT~uIiJafuL
Sete F~ D2..J3l$
11..14 ~G OF BtJRDlNG SlTIBDRAIN SYSIEMS
IU4lJlFmdu:n~ VemlliilW!;
~OOnral1Jn~~Sstm:rn~kv~<I$alCQIm~~i~'~Ssteml.
i1!..1IuStmmpPiitls; i
at.1I1remillfum:rm~amirmm;iimmn rel1gtThl(IDffv~ffur~Jjrii5;lhw:fug! ~ ~~JPllll1'!Jf$ sfuF.l1l1lrel.I
<I$iIrd1~irn1fanre 112..114/;2. i
m.$m.fu~wit veIlt$1mflie:~te<dJttID gmmi~ vemt~ll!: ffur~ <MfunrtfumJ
tJ!hIDRe
~edi ~ tJJre I
~nrili. I
ZIJf!H3 N01ianull.'Iiumlh:rd] flizminng! (]]Hiir~/llil$'/ramdi Z9JT1

Table 12.14.2
SIZE AND LENGTH' OF SUMP VENTS
Diameter of Vent, (inches)
DischargeCapacity 1-1/4 1-1/2 2 2-1/2 3 4
of Sump Pump
(gpm) Maximum Equivalent Length of Vent, in Feet, (Given Below)
10 N.L.' N.L. N.L. N.L. N.L. N.L.
20 270 N.L. N.L. N.L. N.L. N.L.
40 72 160 N.L. N.L. N.L. N.L.
60 31 75 270 N.L. N.L. N.L.
80 16 41 150 380 N.L. N.L.
100 <103 25 97 250 N.L. N.L.
150 Np. <103 44 110 370 N.L.
200 NP NP 20 60 210 N.L.
250 NP NP 10 36 132 N.L.
300 NP NP <103 22 88 380
400 NP NP NP <103 44 210
500 NP NP NP NP 24 130
I. Developed length plus an appropriate allowance for effects of entrance losses and friction
due to fittings, Changes in direction, and changes in diameter. Suggested allowances may be
obtained from NBS Monograph 31 or other acceptable sources. An allowance of 50% of the
developed length may be assumed if a more precise value is not available.
2. No Limit; actual values greater than 500 feet.
3. Less than 10 feet.
4. Not permitted.
12.14.3Pneumatic Sewage Ejectors

Pressure release vents for pneumatic sewage ejectors shall extend to a vent terminal that is separate from
any gravity system vents. Such pressure release vents shall be of sufficient size to reduce the ejector tank to
atmospheric pressure within 10 seconds, but shall be not less than 1-1/4" pipe size.
12.15 SUDS PRESSURE VENTING
12.15.1 Relief Venting

Where fixtures or branch drains connect to a soil or waste stack within a suds pressure zone as described in
Section 11.11.2, a suds relief vent shall be provided for the fixture or branch drain. Suds relief vents shall be
2" minimum size but not less than one pipe size smaller than the drain branch that they serve. Such relief
vents shall connect to the drain branch between the suds pressure zone and the first fixture trap on the
branch. See Figure 12.15.1
Comment: Suds pressure relief vents in Section 12.15 are larger than ordinary ventsfor drainage
systems because the suds are heavier than air. Suds can weightfrom 2 to as much as 19 pounds per cubic
foot.

DRAINAGE STACK
RELIEF VENT
(Note 1)
BRANCH DRAIN FROM

ONE OR MORE FIXTURES
-- (Note 2)
SUDS PRESSURE
ZONE 4
SUDS PRESSURE
ZONE 1 OR 2
NOTES:
1. Relief vents must be sized according to Table 12.15.1.
2. Relief vents must not connect to a suds pressure zone in a vent stack
Figure 12.15.1
RELIEF VENTS FOR DRAIN CONNECTIONS IN A SUDS PRESSURE ZONE
Table 12.15.1
SUDS PRESSURE RELIEF VENTS
Waste Size Relief Vent Size
\';, 2
2 2
3 2
4 3
5 4
6 5
8 6
12.15.2Prohibited Vent Connections

Connections shall not be made within the suds pressure zone of a vent stack that connects at or downstream
nom the base of a soil or waste stack, as described in Section 11.11.2.d.
12.16 SIZE AND LENGTH OF FIXTURE VENTS

12.16.1 Size of Fixture Vents
a. Vents for individual fixtures shall be sized according to Table 12.16.
b. Vents shall be not less than 1-1/4" size nor less than one-half the size of the fixture drain that they
serve.
c. Where a vent pipe serves two or more fixtures, the size of the combined vent pipe shall be based on the

gum of tire drainage fixture units (Dm) for all aftile dr:aiiIsserved.
d. Wfrere,the fixtures;1'remgvented:are not conn:ected:to'tire game di:am ~ tfre stack ~ usaL iir lfaUfe
12.16 sfraII be tire e<DJivaIentstack sizefartlreirtotaI comfuned.DFU road,.based.OII Table t 15.tB..
EXCEPTION: As:otherwise provided in ~Cocfe.
See FIg.1We t2..1l(f~1!-Aanc:l-R
Ta:bIe J2..1!(iJ
SIZE AND LENGmOFVENTS
Sizeof Hixtme-
DI"3inagJ'tl!Inits. DiameteJ7 of ~ent; R~u.ined (I!m:h15)
Staekorr Con- I!'t... I!'f2c 2 12/1:; 3t 41 5' & 8
Ifixture. nected
Drniir
~ M'axiinum ILengttt of~ errtr (Jteet)
I'i2o 8 :f0 [:fa

2 12 30 T:i zoo
2 20 26- :f0 150
3 10 30 100 roo 600
3 30 60 LOa :iQ0
3 60 :iQ 80 400
4- 100 :f:i roo 260 liOOO
4- zoo 1'0 90 50 900
4- 500 20 TO LSO TOO
5 200 H 80 :f:iO LOOO
5 :f00 I{J TO 1'00 900
:f II 00 20 :iQ 200 TOO
6 3:f0 25' :iQ LO0 ' 400 U{JO
6- 6-20 15' 1'0 L2:T 1'00 1roo
6- 96-0 24- 100 L:TO 1000
6- 1900 20 TO 200 TOO
8 6-00 5'a 150 5'00 HOO
8 [400 4'0, IiUO 4Q0 1iLOO
8 ITOO 1'0 80 :f:iO r 10a
8 J6-O0 a 6{J L:iO 80 0
10 1000 T'f 15 rooo
10 2:f0 0 :iQ roo :iOO
10 3800 I{j i &\1 }@
1'0 j'6-Q0 a 6-0 'T:iO
1t'4'" IllNI~ IT
\ '
Ii ~'IIIIIII~ r
~, "-I:
Ii II
Ii Ii
Ii I!
mTIffi'
t.., I:ieJ;rt $ fur imtiuidual'ffxtuwesmust me catleast rv~ <ifttre si;re <nfi:treC!b1aim

tl1rattttrew~, muttrnm1tless
ttret 1:-11/4,"
F~II2Z..n~.n - A
nIlE SJZE 0Jf JNDn'IJmlTA:LHX1i1LTRE:
~
J(J(Jf EIf!!F N.!atianw.5fiamiiJrdl llUmliingz(nujk:--Illustrnttrdl

V.T.R.
J'L
I
I
I 4" OVERALL LENGTH OF LONGEST
I VENT PATH = 100 FEET
I
3" I 3"
r
/ I
L
/ l
I I
I I
I I
I I
PUBLIC PUBLIC
TOILET ROOMS TOILET ROOMS
150 D.F.U. 150 D.F.U.
4" 4"
EQUIVALENT DRAINAGE STACK = 5" (300 D.F.U.)
NOTES:
1. Two groups of public toilet rooms are connectedto a combined vent.
2. The size of the vent for the 4" drain stack from each group with more than 100 DFU must be 3" if the
overall length to the vent terminal is 100feet. (Table 12.16).
3. The size of an equivalent drainage stack with 300 DFU is 5" (Table 11.5.1B).
4. The size of the combined vent for the 5" equivalent stack with 300 DFU and 100 feet is 4" in Table
12.16
Figure 12.16.1 - B
THE SIZE OF VENTS FOR MULTIPLE FIXTURES ON DIFFERENT STACKS
12.16.2 Size of Circuit or Loop Vents

Circuit or loop vents shall be not less than one-half the size of the horizontal drainage branch that they serve.
See Figure 12.16.2

'f
1
/.I VENT STACK
2" / //=--r-I CIRCUIT VENT

/:/ 1 (Note3)
//1 1
// 1 I
/ 2" 1
/ / I I
/// I ,L
4"
( 2" I
RELIEF VENT
(Note 4)
:/
1
A" I
W.C.
W.C.
NOTES:
1. A lower floor is shown. It requires a relief vent because there are more than 4 water closets on the
branch.
2. The horizontal branch drain is 4" size
3. The circuit vent must be 2" minimum size per Section 12.16.2.
4. The relief vent must be 2" minimum size per Section 12.16.3.
Figure 12.16.2
THE SIZE OF CIRCUIT AND LOOP VENTS
12.16.3 Size of Relief Vents

a. The size of relief vents for circuit or loop vented branches of the drainage system shall be not less than
one-half the size of the branch drain being served.
b. Reliefvents for stacks having ten or more branch intervals and relief vents for horizontal offsets in such
stacks shall be the same size as the vent stack to which they connect.
See Figure 12.16.2
12.16.4 Size of Stack Vents and Vent Stacks

The minimum required size of stack vents and vent stacks shall be in accordance with Table 12.16. For the
purpose of sizing, the length of a vent stack or stack vent shall be the developed length from its lowest
connection with the drainage system to its termination in the open air, including any vent headers.
12.16.5 Vent Headers

a. Vent headers or portions thereof shall be sized according to Table 12.16.
b. The number of fixture units (DFU) used to size vent headers shall be the sum of all fixture units (DFU)
on all stacks served by each section of the header.
c. The developed length of vent headers shall be the longest vent length from the vent connection at the
base of the most distant stack to the vent terminal in the open air.
d. The soil or waste stack size used to size vent headers shall be the equivalent size capable of handling
the fixture unit load (DFU) on the vent header, based on Table 11.5.1B.
12.16.6 Aggregate Size of Vent Terminals

a. Each building sewer shall be vented by one or more vents extending from the drainage system, or
branches thereof, to the open air above the roof.
b. Stack vents and vent stacks shall be sized according to Table 12.16.4.
c. The aggregate cross-sectional area of all vent terminals serving a sewer shall be not less than the cross-
sectional area ofthe minimum required size of the building drain that they serve, at the point where it con-
nects to the building sewer. (See Table 12.16.6 for the cross-sectional areas of pipes).
EXCEPTION: The aggregate cross-sectional area requirement shall be exclusive of any requirements to
prevent frost closure under Section 12.5.
Table 12.16.6
NOMINAL PIPE CROSS SECTIONAL AREA (Sq. Inches)
Nominal Pipe Size (10) Cross Sectional Area (sq in.)
1'/, 1.5
]1/2 1.8
2" 3.1
21/2" 4.9
3" 7.1
4" 12.6
5" 19.6
6" 28.3
8" 50.3
10" 78.5
12" 113.1
15" 176.7
12.16. 7 Underground Vent Piping

The minimum size of vent piping installed underground shall be 1-1/2".
12.16.8 Reserved
12.17 COMBINATION WASTE AND VENT SYSTEM
12.17.1 Where Permitted
a. A combination waste and vent system shall be permitted only where conditions preclude the installation
of a conventionally vented drainage system as otherwise required by this Code.
b. Combination waste and vent systems shall be limited to floor drains and other floor receptors, sinks,
lavatories, and standpipes.
12.17.2 Trap Size

Traps in a combination waste and vent system shall be the normal size for the particular fixture. See Table
5.2.
12.17.3 Trap Arms

a. Fixtures shall be considered to be vented at the point that they connect to a combination waste and vent
system.
b. Where fixtures have conventionally sized trap arms, the maximum length of the trap arm from the weir
of its trap to the point of connection to the combination waste and vent systems shall be as limited in Table
12.8.1.

c. In the case of fixtures with above-the- floor outlets, the vertical drop at the end of the trap arm shall be
one size larger than the trap ann and be considered as the beginning of the combination waste and vent
system.
d. Floor-outlet fixtures shall also be permitted to drop into a vertical combination waste and vent that is at
least one size larger than the trap arm.
e. Where a fixture trap arm is sized as a combination waste and vent, its length shall not be limited and it
shall be considered as a branch of the combination waste and vent system.
f. The maximum vertical drop from a fixture trap arm to a horizontal drain below shall be 6 feet.
12.17.4 Pipe Sizing

The piping in a combination waste and vent system shall be sized according to Table 12.17.4, based on the
number of drainage fixture units (DFU) served and the slope of the piping.
EXCEPTION: No pipe shall be smaller than any section of piping upstream, including vertical drops from
trap arms.
Table 12.17.4
PIPE SIZING FOR COMBINA TION WASTE AND VENT SYSTEMS
COMBINA nON WASTE & VENT SIZES
LOAD slope slope slope slope
I/S" per ft 1/4"perft 3fs" per ft 1/2"per ft
3dfu 4" 2" 2" 2"
12dfu 4" 4" 3" 3"
20 dfu 5" 4" 4" 4"
180dfu 5" 5" 4" 4"
218 dfu 6" 5" 5" 5"
390 dfu 8" 8" 5" 5"
480 dfu 8" 8" 6" 6"
700 dfu 8" 8" 6" 6"
840 dfu 10" 8" 8" 8"
1600dfu 10" 10" 8" 8"
1920dfu 12" 10" 10" 10"
12.17.5Maximum Slope
All piping in a combination waste and vent system shall be horizontal and sloped at not greater than 1/2 inch
per foot.
EXCEPTIONS:
(1) Vertical drops at the end of trap arms.
(2) Vertical drops of not greater than 45 degrees from horizontal where the vertical drop is not greater than 6
feet and the offset is at least 10 pipe diameters from any turn or branch connection.
12.17.6Branch Connections
a. Connections to mains and branches within combination waste and vent systems shall be made horizon-
tally at a slope not greater than 1/2 inch per foot.
b. Branch connections shall not be made in vertical drops or offsets.

IU7!_7i~mmDistaIrces;
The dfutance Oetween: IDrII,.otIffietg:~and fu:ancfr c:onnectiilUIS i'rnc:om:I1ri:iIat:[Q1Ii
waste and Ven1!pipii:rg mIL
lJrenatt fuss; t:fum ro. pipe diameteTIf.
JlU1'.8'COiIl:medmms:tmCa,mven1it))rEm.B'JiaimIgeSY!i:ems;
at.(CQmfriiIa1iOIL waste and vent ~stem$ ghall e:xtencllto)tIre:[JIi:n1I gffc:oIJ:JIectii;m;
to)aJ~~
~and1C:OIWen1iOIIa11yven:ted.cfrninageSj'stem..
m.Atttfr.t=tnMTItof c:onnectimr,.tIle pipe ~ <irlf tIle c:l!JIWentii;maf$J'ste:n;nsfra1]jae at J'eas:ttal'auge a tIIe
~ $J'ffi:Elrn,.
and siZ:ed!to.acc:epttlIe:ad'<fettcfuall:rage[aadlffumntfre~ ~~.
G:.$u:c:En
~CJII; fiMImtIre:c:omlTIiIatrams-ysterrr:tQ)tfr.t=~emiQ1::rat S>jstem:ill:aITae ~ at amangre
afuTh<ell~ otnott refS;tlJarn2Z-TI/Z~IICJ1in:n;rretfumt ti Gfegrees..
:DU71"'COIm~O!n:mmidrJm]1r~
~~ firom imfi~icfuaJ1mtIu:es: are:cf~:I$ atc:omFriiIatfurnwaste and1ventI amIlaIr<:~ t@
aJ.c:~entfu:t:ml!idJ::aillage$J'stem,.tIIe C:Q1Illooiom
from tIIe ~ 1Xk C(\}lIl\'fentiima:I!
~steml gfud;JJ
IJe ~
~toJ$eillJ[QlI TIz..rT.g:
n.18 OJfDEK DESIGNS

Wtmt1ing~srems,mrt1dkscniUed1 iITtlIi$ (cbtre1IIffiY'IJe[Je:mnitted1E7~rtIIeA~' HaviiIg~m iitftl1:e:J
~iiktfrenmatetriijJII~~ $e1Ji:om nZZ:.TI and1aIr<:~iifu}Frr'W([~~'ai~pro~
~. QS'eeAmJemfi~E - $I?0lAL. IDJJES.TI<GJN
IffiJUMBWG $Y$EEMS.)
lllflTfi Natitmw! fffarrdiwdi ElUmfiing: Cade"-l11 iLstralEd. 3U$

Blank Page
306 2003 National Standard Pumbing Code-1l/ustrated

Chapter 13
Storm Water Drainage

13.1 GENERAL

Roofs, paved areas, yards, courts, and courtyards shall be drained to either a storm sewer where available, a
combined sewer where necessary, or to a place of disposal satisfactory to the Authority Having Jurisdiction.
EXCEPTION: Storm water from one- and two-family dwellings may be discharged on lawns or streets
provided that the storm water flows away from the dwelling and does not otherwise create a nuisance.
13.1.2 Storm Water Drainage to Sewer Prohibited

Storm water shall not be drained into sewers intended for sewage only, except as approved by the Authority
Comment #1: The peak storm waterflows in combined sanitary and storm sewer systems can overload
the sewage treatment facility, causing it to bypass untreated sewage into its point of discharge.
Comment #2: In many cities with combined sewers, it is impractical to install separate sewers in the
downtown areas because of the number of existing utilities under the streets.
Comment #3: Somejurisdictions with combined sewers require that new or renovated buildings have
separate sanitary and storm building drains so that they could be connected to separate sewers in the
future.
13.1.3 Sanitary and Storm Sewers

Where separate systems of sanitary drainage and storm water are installed in the same property, the storm
and sanitary building sewers and drains may be laid side by side in the same trench.
13.1.4 Reserved
13.1.5 FoundationDrains
a. Foundation drains shall be provided around the perimeter of basements, cellars, crawl spaces or any
building space below grade. The drains shall be positioned either inside or outside of the footings, and shall be
of perforated or open-joint approved drain tile or pipe not less than 3" pipe size. The invert of foundation
drains shall be not less than 2 inches below the underside ofthe floor slab being protected.
b. Foundation drains shall be laid in a filter bed of gravel, crushed stone, slag, approved 3/4" crushed
recycled glass aggregate, or other approved porous materials. The bottom of the filter bed shall be no higher
than the bottom of the base course beneath the floor slab. There shall be not less than 2 inches of filter bed

:beneafh the fOImiJafiOllmain. Wlu::re form iJafion ib:aim;RT-flocared outside .of:the fo.otings.,iherot:$hilll:be.at
Jfll5t.6 Jncl1eBDf1llrer rea M<Ne the lOp Dfibf::p~.
.c.Wfuill'-f:wrm-nafi011~ JiTeJ.oca1edml !theiin:re:riior:siik,ofo.o1ing5.,wf:fft)oo1esmot les5 than 3 14"in
ili3TT1ffieT:Srum ~be;:pr-oWiied.onlD-incl1~:above the:top \Ofthe foDting.and bene.afh:the:bottom ~nr.fucp.<Df
the Iflo.oniliib.
..d.JDrainage frmn ,formiJatio.ns:s1uill'be illsCb.arged :to.Jl.51:ormJkall,51reet, lliley.,.approved 'w.ater.co.n:rBe,'or
:atgrade. ~ilmcTmTud.at ~ the po.im.of.di5charge Bhal1'be 111leas! 10 1fuetfro.m:any;p1'~ 1ine;and
Bhal1not.cT~ .a TIliifrnnce.
ot:.~e io.unda:tinn.draJm;JiTehdlow:the T~uiTed !paint ,o.f~e, ,0Il:eill :mme.automatic:SIJ:IIWIFJlIIIW5
:5ha1l'be ;p1'ffi'ideil.lI'lrepllIIlpOTp.u.m,ps:shall 'have aiffiqnate ,capacity to..co.nwey.all fu.ai:ru!ge:toits pIDnt<Df
cmch aTD. T:he TTlimT11l1tTl pnmp.c.apac:i:ty:ShallDe 1:5gallo.ns per 1Iiinu1e111the J"equiTeddi5cl1arge:bead. :snnw
pits BhaIl'be .sized 10..accommodate the pnmp(:s), 115T~oTTt111P.niIP.d by the pump :mannfactm.er, :bnt:Srum:be :not
Jem;than 1:5inChes :in.diame1er'l1orJe551han 1'8:inChesiIeep.:Sump pits Bhall DeJEovideil wjth :fitted-CDer5.
Pits shall De lo.ca1eillo avoid foot traffic W;bcr-ftheir COVf:Tsdo. no.t have sufficient.51:T.ength1o.cm::ry:SIJd1
we@rt. DiBCharge Jines frmn :snmppnmps 5hllil be .sIT.e.daccm.d:inE 10.1nedesign pump .c.apaeJt.y.and:iilia]}:be
'I101:m than 1-114"PWe:Size. A clJeCkvmve BhaITl ~itbcr JJe inCo.rpo.ratedinto.ceaeb:Sumppump or theiinB11illcil
:inthe ili5Cb.argeline from ead1.5UIIlpPlIIIlp. :except 1ha1,Cbec'kv.alves may 'bee1iminated w1wre the diRCharge
pipe 'would De.sUbject:to.fr~. Under Bncl1.conditiilll51be:Sumppit 5halJ 'be JldeqTIat~1ysized 10.In'tWfmt
:ShOT1cyding o.fibepnmp.
f. Where:Sump p.u.m,psdiChar;e111grade ml nnpaved srn:faces, the ilisChm:gepipe 5luill ~ :toJl i>j1lmfu
bloCk .orequivalent, 'V.fui.ch shall 'be~lnfli1 10-contain the disc'lun;ge,Teduceits vclo.city, .and:avoid.di51:uibiQg
lidjacent RTem;.Where:ne.cessm:y., the .ilisc'barge pipe :sluillterniina1e 'viiiban .elbo.w 10 direct 1be :fWw ~
the ~la5b bloCk. 5pla5b bloCks hall 'be'm least 24 inches long.
g. The water ~ 10 'W1UeT-o,pernted5!Onn w.ater:sump PlIIIlp5:Shall 'be pFo:rected fj-~ nacldlow in
accor..dance'with Section 1'05.
See F~.es 13..L5-:A JI!IIt1-:B
'F.uJDRSU&l1
:!"
;F,[)JJH])""-IDNDRAIN
13"'AlINIMUM:5I2E
rtiJOITiES:
1. Tire invertnfthe iDlmdation r:h:ainmust be:at least 2 inches below thEunrleTsirleDfttheilDmslrib.
:2. The 'fitter bed rnus:t:be at 1eas:t2".beneath thE battornof1herlrain qJipe B1'1d:at least B" Bbove1hE ~
m1he pipe. Installhlg a-lfil:tertabricDverfueffitter:bed willkeep fine BoiltJElr1icle:siIDmclqggh1g:the
qJDTDusopenin,gs.in100bed.
3. Fnundation drBinsrequiTBihesarneEarthroverLlSurainagepiping.
Figure 113.11..5
- A
A FOUNDATION DRAJN 'OUTSIDE 'OF A FOOTING
308 2(}(B National Standard Pumbing CodE-(lllustr..atel

OUTLET OVER SPLASH BLOCK
OR OTHER APPROVED
POINT OF DISPOSAL
\ ~ NOTE 1
1 1/4" MINIMUM
24" MIN
~ CHECK VALVE
IZ ~ SUMP PUMP - PEDESTAL

/ OR SUBMERSIBLE
/ FITTED COVER
~
r
18" MIN
DEPTH A A A Ai
~ FOUNDATION DRAIN
~~
I
"t
--\~
SEE FIGURE 13.1.5-A
~5.
L MINIMUM
1 INSIDE
DIAMETER
NOTES:
1. Where subject to freezing weather, the discharge pipe should be sloped downward so that the outlet
drains by gravity.
Figure 13.1.5 - B
A SUMP PUMP FOR FOUNDATION DRAINS

13.1.6 Areaway Drains
a. Drainage shall be provided for open areaways below grade where storm water may accumulate.
Areaways include outdoor spaces that provide access to basements or floor levels of a building that are below
grade. Drains in such areas shall be sized according to Table 13.6.2 and shall include strainers as required for
roof drains or floor drains.
b. Areaway drains shall not connect to a foundation drain.
EXCEPTION: Areaways not exceeding 100 square feet in area.
See Figure 13.1.6
AREA DRAIN
AT BASE OF
I I
Y
STAIRWELL
t
r------- .,
~
~
I SUMP PUMP
(WHERE REQUIRED)
FOUNDATION DRAIN
(NOTE1)
/ AREAWAY DRAIN
(NOTES2 &3)
~
FOUNDATION DRAIN _I
(NOTE 1) 1
NOTES:
1. The foundation drains can be inside or outside of the footings. See Figures 13.1.5 - A and 13.1.5 -
B.
2. The areaway drain can connect to a foundation drain if the size of the areaway (and any adjacent
areas that drain into the areaway) is 100 square feet or less. It must discharge separately if the
area being drained is largerthan 100 square feet.
3. Drain pipes for areaways must be sized according to Table 13.6.2, based on the rainfall rate and the
size of the areaway and any adjacent areas that may drain into the areaway. The minimum drain
pipe sizes are 2" if sloped 1/4 in./ft or more and 3" if sloped 1/8 in./ft.
Figure 13.1.6
THE ARRANGEMENT OF AN AREAWAY DRAIN
13.1.7 Window Well Drains

Window wells shall be drained as required for areaways, except that window wells not greater than 10
square feet in area shall be permitted to drain into a foundation drain, either directly by means of a 2" mini-
mum size drain, or indirectly through a porous filter bed. See Figures 13.1.7-A and-B

WINDOW
WELL
WINDOW WELL
DRAIN PIPE
-
(Notes 2 & 3)
PIPED DIRECTLY TO THE SUMP IF

WINDOW WELL EXCEEDS 10 SQ. FT.
J -==-- FOUNDATION DRAIN
(Note 1)
NOTES:
1. The foundation drains can be inside or outside of the footings. See Figures 13.1.5 - A and
13.1.5-8.
2. The window well drain can connect to a foundation drain if the size of the window well (and any
adjacent areas that drain into the window well) is 10 square feet or less. It must discharge sepa-
rately if the area being drained is larger than 10 square feet.
3. Drain pipes for window wells must be sized according to Table 13.6.2, accounting for the rainfall rate
and the size of the window well and any adjacent areas that may drain into the window well. The
minimum drain pipe sizes are 2" if sloped 1/4 in./ft or more and 3" if sloped 1/8 in./ft.
Figure 13.1.7 - A
A WINDOW WELL DIRECTLY DRAINED
WINDOW
FOUNDATION DRAIN
(NOTE 1)
NOTES:
1. The foundation drain must be outside of the footings. See Figure 13.1.5 - B.
2. The porous filter bed must extend from the area drain in the window well to the foundation drain.
Installing a filter fabric between the earth and the filter bed will keep the porous bed from becoming
clogged with fine soil particles.
Figure 13.1.7 - B
A WINDOW WELL INDIRECTLY DRAINED

13.1.8 Parking and Service Garages
Storm water drainage from parking and service garages shall be in accordance with Sections 6.3.I.d and
6.3.I.e.
13.1.9 Reserved
13.1.10 Roof Drainage
13.1.10.1 Primary Roof Drainage

Roof areas of a building shall be drained by roof drains or gutters. The location and sizing of drains and
gutters shall be coordinated with the structural design and pitch of the roof. Unless otherwise required
by the Authority Having Jurisdiction, roof drains, gutters, vertical conductors or leaders, and horizontal
storm drains for primary drainage shall be sized based on a storm of 60 minutes duration and 100-year
return period. (See Appendix A)
13.1.10.2 Secondary Roof Drainage

1. Where parapet walls or other construction extend above the roof and create areas where storm
water would become trapped ifthe primary roof drainage system failed to provide sufficient drainage,
an independent secondary roof drainage system consisting of scuppers, standpipes, or roof drains shall
be provided. Secondary roof drainage shall be sized for a 100-year, IS-minute storm (see Appendix A).
The capacity of the primary system shall not be considered in the sizing of the secondary system.
2. Where secondary drainage is provided by means of roof drains or standpipes, the secondary system
shall be separate from the primary system and shall discharge independently at grade or other ap-
proved point of discharge.
3. Where secondary roof drainage is provided, the overflow level(s) into the secondary system shall be
established by the amount of ponding that is allowed in the structural design of the roof, including roof
deflection. An allowance shall be made to account for the required overflow head of water above the
secondary inlets. The elevation of the secondary inlet plus the required overflow head shall not exceed
the maximum allowable water level on the roof.
4. Scuppers shall be sized as rectangular weirs, using hydraulic principles to determine the required
length and resulting overflow head (see Appendix A). Secondary roof drains and standpipes shall be
sized according to Table 13.6.1 Where standpipes are used, the head allowance required under Section
13.1.1 0.2(3) shall be not less than 1-1/2 inches.
5. Strainers shall not be required on open standpipes when used for secondary inlets.
13.1.10.3 Vertical Walls

Where vertical walls drain onto roofs, an allowance based on 50% of the maximum projected wall area
shall be added to the roof area onto which each wall drains.
13.1.10.4 Equivalent Systems

When approved by the Authority Having Jurisdiction, the requirements of Sections 13.1.10.1 and
13.1.10.2 shall not preclude the installation of an engineered roof drainage system that has sufficient
capacity to prevent water from ponding on the roof in excess of that allowed in the roof structural
design during a 100-year, IS-minute storm.

13.1.11U{u.lmm,onsFllDW
WiImr-e<afflIfinnoIl5flDw:IIama:SpTing or gr-onnd w.atcr i5,encoI.III:rer-ed
riD..afonn.dafion dr.a.inag-e:system -or
cthe:r :SUb5ollmain, the :disCharge 5haI1bf p.iper.l10a :5torrnewer or .approv-erlw.a:terCDI.JrBe.
a1.D Jlm:kw.ate.rV:a'lva
'Wfuer.efD.unda1iioo..dnrimi,.ar-eawcay.drains, wtindIDwwcll iinrins, mothcr:5torrn w..a:terili.ainBillschargeby
~ :aOOJIrBlibje.ct10 :badd1ow funn :fueirpoint &Ifillsrfuar,gt:,a ~ v~ 5haI1bf :p:nwiirerlin:the
,dmcl1arP;e1iDe.B.aCkwlI1erv~:Shall comp~ 'w.ifu:theI-e.qIiir;ementsof Section 55.
13..2 MATERIALS
See ~ 3.7. See T:a1:>1e
3.7 fm :appiIilWe.d
~ fDrstOTmwJrterdr.ainage.
13.3 T.1lAPS IN STORM: DIlAINAGE SYSTEMS
Ill.I Ge.ner.a1l
<R.If;ny1B5luill :belinstaIle.d:ina :s1o.ml.drai:nage~jftt ..ccmnect510..ammbined .sewer .conveying both
~ <Bnd:5tom1w.ater.
EKDBPTiIiGN: illliapBBhall not:he rr~rilWher .FODfdr..ain5.,
nUn Je.a.dt:r5,.and otberinlets.ar-e.at locations
~~!lltlCler:Sec:tiDn 12.44 fu-ven1 reIJIiimfu;.
:b. !FlDm&insorcthe:rT~on;'Wifuin..a 'buildingifuall ibemruvjrlmilly :trappedjf:they.ar-e .connected to a
Rtmm .fu:ainage :5}'51em,Tegarillem;-ofvillefumm mot:the .sewer is -cmrlliined.
(c. llJ:a,pB:regnir;eduniler1hi :BeCtionshaJ!l-aornplywifb :theT-e.quirementsof Secti on 53.1, .53 2, 533, :53.5
.ailll ll33:2. 1fnaws:ffualI1l:urv;f..acres5ible de.an0J.I!i0TOtberII:I1e.ans
.of dearing:the 1rap.
'Comment: !Filoorilrnim or~atlrer!r.CJJ;Piors

Iihm nhUJonmxJeil !ton 'Storm ilrmnag.e systEm or ombiTJd
'StIHW.anil 8r csu'/jjJ.mttJIJ"e,ut!JJOr..o:iilJn
,td'ilre:trJgJsed1 ,1IUlSi:be]1rJJ.1iiiI.eiJ
'With .a ~s.al1r.a'por 'lJi'hr
:me.ansofnuiintJiitiing fire ltrJgJ li.Ul. :J;,e,eS,edion 53.6.
1133..1 LDcaDOB ,ofT:r.a;ps

Wiher-e1rBp5JIr;fT.qllirril:under'Sec:fum B 3.il .a.1~ 1iha.Il:bejnmaf1P.dcitheron miliVirlna:Jbnmchesof1be
:BtIDmn dkaiTrla..ge
Y51em"or:in:the1bull.lling'tmun<fuHrn:illfullil.lling51~mn$ewer 'befl1:me,tt-cffimec:ts10 ihe.com-
ltiine.Q~.lnr'1pE 5hall mot 'bfinmal1P.ii .inWcmITIDm;
'w.!wrfuey wiJil be :Slibject10 freezinp;. 'Where 1r.apsJIr
II"<eqIDredfm:nii:n :leaders, fue Jriinimllm;farth .covm mmL be.as r;eguirerlin 'Section 2.Jl:b. 'See Frigm-.133.2
201B National StandmiiiPllmbinglCode-lliLr:ilr..atd 3113

STORMWATER
CONDUCTORS
SOIL STACK SANITARY BUILDING
~IN
1-
fAT LEAST 10'

FROM SOIL STACK
(NOTE 1)
~
COMBINED BUILDING DRAIN
WYE FITTING
(NOTE 2)
TO COMBINED BUILDING SEWER
NOTES:
1. The trap is required when any of the storm water inlets are at locations where sanitary vent termi-
nals would not be permitted in Section 12.4.4. If all storm water inlets are at locations where
sanitary vent terminals would be permitted, the trap is not required. The storm water inlets will be
the same as vent terminals for the sanitary drainage system. Only those inlets in prohibited loca-
tions for sanitary vent terminals need to be trapped.
2. The connection between the building storm drain and the building sanitary drain needs to be a
horizontal wye fitting that is at least 10 feet downstream from any soil stack.
Figure 13.3.2
A TRAP IN A STORM DRAINAGE SYSTEM
CONNECTED TO A COMBINED SEWER
13.3.3 Size of Traps

Traps shall be the same size as the drain pipe in which they are installed.
13.3.4 Reserved
13.4 LEADERS OR CONDUCTORS AND CONNECTIONS
13.4.1 Notto be Used Improperly

Leaders or conductors shall not be used as soil, waste, or vent pipes nor shall soil, waste, or vent pipes be
used as leaders.
13.4.2 Protection of Rain Water Leaders

Rain water leaders installed along alleyways, driveways, or other locations where they may be exposed to
damage shall be protected by metal guards, shall be recessed into the wall, or shall be constructed from
ferrous alloy pipe. See Figure 13.4.2
Comment #1: The" 10feet downstream" requirement allows the sanitary discharge to stabilize before
mixing with the storm waterflow. It also reduces the backpressure on the sanitary drainage system that
may be caused by heavy storm water discharges.
Comment #2: The horizontal wye connection between the two drainage systems permits the flows to mix
more uniformly without blocking the drain.
314 2003 National Standard Pumbing Code-/llustrated

LEADERS 7
PLASTIC OR
SHEET METAL
LEADER
GALVANIZED STEEL
OR CAST IRON
DOWNSPOUT BOOT
DRIVEWAY
~ETAL
GUARD
L RECESS IN
BUILDING
WALL
Figure 13.4.2
PROTECTION OF RAIN WATER LEADERS
13.4.3 Combining Storm with Sanitary Drainage

The sanitary and storm drainage system of a building shall be entirely separate, except that where a combined
sewer is used, the building storm drain shall be connected in the same horizontal plane through a single wye
fitting to the combined sewer at least 10 feet downstream from any soil stack.
13.4.4 Double Connections of Storm Drains

Where the sanitary and storm drains are connected on both sides ofthe combined sewer, single wyes shall
be used and the requirements of Section 13.4.3relative to the location of connections shall also apply. See
Figure 1.2.15
Comment: Double pattern wyefittings are not permitted to connect sanitary drains and storm drains to a
combined drain. This is to prevent a heavyflow in one drain branch from causing a backpressure in the
other drain branch.
13.5 ROOF DRAINS
13.5.1 Compliance and Materials

Roof drains shall comply with ANSI A 112.21.2M and be constructed of coated or galvanized cast iron,
bronze, stainless steel, plastic, or other corrosion-resisting materials. Drains shall include any deck clamps or
other appurtenances necessary for installation and coordination with the roofing system.
13.5.2 Strainers for General Use

Roof areas, except those draining to hanging gutters, shall be equipped with roof drains having strainers
extending not less than 4 inches above the surface of the roof immediately adjacent to the roof drain. Strain-
ers shall have an available inlet area, above rooflevel, of not less than 1-112times the area of the conductor
or leader to which the drain is connected.

13.5.3 Strainers for Flat Decks
Roof drains on patios, sun decks, parking decks, and other areas subject to pedestrian and/or vehicular traffic
shall have flat gratings with a free inlet area of not less than two times the cross-sectional area of the drain
outlet. Such drains shall not be located where they cannot be readily inspected and maintained on a regular
basis.
13.5.4 Roof Drain Flashings

The connection between roofs and roof drains which pass through the roof and into the interior of the building
shall be made watertight by the use of proper flashing material.
13.5.5 Roof Drain Restrictions

The roof drain size shall not be restricted by insertion of any roofing material or other objects to insure water
flow into the drain.
13.6 SIZE OF LEADERS, GUTTERS AND STORM DRAIN PIPING
13.6.1 Vertical Conductors and Leaders

Vertical storm water conductors and leaders shall be sized according to Table 13.6.1. Where a vertical pipe
section is smaller than the preceding horizontal pipe section, the reduction in size shall be made in the vertical
pipe section.
13.6.2Size ofHorizontal StormDrainPiping

Horizontal storm drain piping shall be sized according to Table 13.6.2. Such piping includes horizontal offsets
in storm water conductors, building drains, building sewers, and branches thereof. The size of the horizontal
drain piping shall not be reduced in the direction offlow.
Table 13.6.1
SIZE OF VERTICAL CONDUCTORS AND LEADERS
Dia. of
Condo or Design Flow Allowable Projected Roof Area at Various
Leader in Condo Rates of Rainfall per Hour (Sq. Ft.)
(inches) (GPM) I" 2" 4" 5" 6"
2 23 21 76 1088 544 435 363
3 67 6440 3220 1610 1288 1073
4 144 13840 6920 3460 2768 2307
5 261 25120 12560 6280 5024 4187
6 424 40800 20400 10200 8160 6800
8 913 88000 44000 22000 17600 14667

Table 13.6.2
SIZE OF HORIZONTAL STORM DRAINS
Dia. of Design Flow Allowable Projected Roof Area at Various

Drain of Drain Rates of Rainfall per Hour (Sq. Ft.)
(inches) (GPM) ." 2" 3" 4" 5" 6"
Slope '/'6in/ft
2
3
4
5 100 9600 4800 3200 2400 1920 1600
6 160 15440 7720 5147 3860 3088 2575
8 340 32720 16360 10907 8180 6544 5450
10 620 59680 29840 19893 14920 11936 9950
12 1000 96000 48000 32000 24000 19200 16000
Size (GPM) I" 2" 3" 4" 5" 6"
Slope II, in/ft

2
3 34 3290 1645 1097 822 658 550
4 78 7520 3760 2507 1880 1504 1250
5 139 13360 6680 4453 3340 2672 2230
6 222 21400 10700 7133 5350 4280 3570
8 478 46000 23000 15333 11500 9200 7670
10 860 82800 41400 27600 20700 16560 13800
12 1384 133200 66600 44400 33300 26640 22200
15 2473 238000 119000 79333 59500 47600 39670
Size (GPM) I" 2" 3" 4" 5" 6"
Slope II" in/ft

2 17 1632 816 544 408 326 272
3 48 4640 2320 1547 1160 928 775
4 110 10600 5300 3533 2650 2120 1770
5 196 18880 9440 6293 4720 3776 3150
6 314 30200 15100 10067 7550 6040 5035
8 677 65200 32600 21733 16300 13040 10870
10 1214 116800 58400 38933 29200 23360 19470
12 1953 188000 94000 62667 47000 37600 31335
15 3491 336000 168000 112000 84000 67200 56000
Size (GPM) I" 2" 3" 4" 5" 6"
Slope ,(, in/ft

2 24 2304 1152 768 576 461 384
3 68 6580 3290 2193 1644 1316 I] 00
4 156 15040 7520 5013 3760 3008 2510
5 278 26720 13360 8907 6680 5344 4450
6 445 42800 21400 14267 10700 8560 7130
8 956 92000 46000 30667 23000 18400 15330
10 1721 ]65600 82800 55200 41400 33120 27600
12 2768 266400 133200 88800 66600 53280 44400
15 4946 476000 238000 158667 119000 95200 79330
NOTES:
I. Tables 13.6.1 and 13.6.2 are based on the rainfall rates shown.
2. Local practice of the Authority Having Jurisdiction should be consulted for the value to use
for aparticular location.

13.6.3 Size of Roof Gutters
The size of semicircular roof gutters shall be based on the maximum projected roof area, according to Table
13.6.3.
Table 13.6.3
SIZE OF ROOF GUTTERS'
Diameter of Maximum Projected Roof Area for Gutters
Gutter2 '/16 in SIope3
Inches Sq. Ft. GPM
3 170 ~
4 360 15
5 625 26
6 960 40
7 1,380 57
8 1,990 83
10 3,600 150
1. Table 13.6.3 is based upon a maximum rate of rainfall of4 inches per hour. Where
maximum rates are more or less than 4 inches per hour, the figures for drainage area shall
be adjusted by multiplying by 4 and dividing by the local rate in inches per hour. See
Appendix A.
2. Gutters other than semicircular may be used provided they have an equivalent cross-
sectionalarea.
3. Capacities given for slope of 1/16 inch per foot shall be used when designing for greater
slopes.
13.7 RESERVED
13.8 SIZING FOR CONTINUOUS OR INTERMITTENT FLOWS

Continuous or intermittent flows from a sump pump, air conditioning condensate drain, or other approved discharge
into a storm drainage system shall be determined in gallons per minute flow. Air conditioning condensate drainage
shall be based on not less than 0.006 gpm/ton. Such flows shall be added to the stormwater load on the storm
drainage system, which shall also be determined on the basis of gallons per minute according to Table A.I and
Section A.3 in Appendix A.
13.9 CONTROLLED FLOW STORM WATER SYSTEM
13.9.1 Application
In lieu of sizing the storm drainage system on the basis of actual maximum projected roof areas as previously
described in this Chapter, the roof drainage system, or part thereof may be sized on equivalent or adjusted
maximum projected roof areas which result from controlled flow and storage of storm water on the roof
provided flow control devices are used and subject to the approval of the Authority Having Jurisdiction.
13.9.2 Design
A controlled flow storm water system shall be designed, installed, inspected and certified as an engineered
special design plumbing system as outlined in Appendix E of this Code.

Special Requirements For Health Care Facilities
14.1 GENERAL
This Chapter applies to special fixtures and systems that occur in health care facilities and to the special plumbing
requirements in such facilities. Ordinary plumbing in such facilities shall comply with the other applicable Chapters
of this Code.
14.2 WATER SERVICE

Where required by the Authority Having Jurisdiction, hospitals and similar health care facilities shall have dual
water service lines to maintain a water supply in the event of a water main failure. Where possible, the service
pipelines shall be connected to different water mains so that a single water main break can be isolated and re-
paired without shutting off all water service to the facility.
14.3 MEDICAL GAS AND VACUUM PIPING SYSTEMS
14.3.1 General
The installation of medical gas and vacuum piping systems shall be in accordance with the requirements of
either NFPA 99 - Standard for Health Care Facilities or NFPA 99C - Gas and Vacuum Systems.
14.3.2 Professional Qualifications ofInstallers, Inspectors and Verifiers

Installers (including brazers), inspectors, and verifiers of medical gas and vacuum systems shall meet the
requirements of ANSI/ ASSE Series 6000 - Professional Qualification Standard for Medical Gas Systems
Installers, Inspectors, and Verifiers, or the equivalent.
14.4 PROTRUSIONS FROM WALLS

Drinking fountains, control valves, medical gas station outlets, vacuum inlet stations, risers, cleanout covers, and
other devices shall be fully-recessed in corridors and other areas where patients may be transported on a gurney,
hospital bed, or wheelchair. Protective guards shall be provided where necessary.
14.5 MENTAL PATIENT ROOMS

Piping and drain traps in mental patient rooms shall be concealed. Fixtures and fittings shall be vandal-proof.
Comment: Plumbing that is accessible to mental patients must be suicide-proof, vandal-proof, and
sound-proof. Piping is installed in chases that are not accessible to the patients. Special fixtures, such
as combination lavatory/toilets, are availablefor such applications. The fixtures are pushbutton
operated to avoidfaucet handles. Most fIXtures are constructed of stainless steel. The plumbing fIXtures
used in mental facilities are similar to those used in correctional institutions.

14.6 PROHIBITED LOCATIONS FOR ICE STORAGE
Ice makers or ice storage chests shall not be located in a Soiled Utility Room or similar areas where subject to
possible contamination.
14.7 CROSS CONNECTION CONTROL AND BACKFLOW PREVENTION

a. Backflow prevention shall be in accordance with Section 10.5.
b. Vacuum breakers for bedpan washers shall be not less than 5 feet above the floor.
14.8 CLINICAL SINKS AND BEDPAN WASHERS
14.8.1 General
a. Clinical sinks and bedpan washers, and flushing-rim service sinks shall be installed in the same manner
as water closets. Where such fixtures have a vent connection on the inlet side of their trap, a local vent shall
be provided in accordance with Section 14.9.
b. Clinical sinks shall not be used as a substitute for non-flushing service sink, nor shall a non-flushing
service sink be utilized to clean bedpans.
c. Vacuum breakers for bedpan washers shall be installed in accordance with Section 14.7.b.
See Figure 14.8

VACUUM BREAKER ~ WALL HUNG
BEDPAN WASHER
B
MIXING VALVE
~
- HAND SPRAY WITH

VOLUMECONTROL
WATER CLOSET-
WALL CONTROL TYPE
~ ~ VACUUM BREAKER
SINK FAUCET \ ib
~nHf)
- HOSE AND
SPRAY NOZZLE
/ DIVERTER
I ASSEMBLY
WATER CLOSET OR
SERVICE SINK WITH
FLUSHING RIM
- (CLINICAL SINK)
1-
WATER CLOSET OR
SERVICE SINK WITH
FLUSHING RIM FOOT VALVE
(CLINICAL SINK)
11 CONTROL
DIVERTER TYPE
FOOT CONTROL TYPE
NOTES:
1. The divertor type of bedpan washer is typically installed in a patient toilet room. When the divertor
is fully raised, the flush valve supplies the water closet bowl in the normal manner. When the
divertor is lowered, the flush valve supplies the divertor to rinse the bedpan. After the bedpan has
been rinsed into the water closet, the divertor can be raised and the water closet flushed. The
elevation of the flush valve vacuum breaker above the overflow rim level of the water closet should be
as recommended by the manufacturer.
2. The wall control type of bedpan washer is typically installed in a patient toilet room. The bedpan is
rinsed into the water closet bowl using the hand spray from the wall control unit. The water closet is
then flushed using the flush valve. Section 14.7.b requires that the vacuum breaker in the wall
control unit be at least 5 feet above the floor to prevent a cross connection.
3. The foot control type of bedpan washer is typically installed in a soiled utility room with a clinical
sink. The bedpan is rinsed into the water closet bowl using the hand spray and foot control valve.
The clinical sink is then flushed using the flush valve. Section 14.7.b requires that the vacuum
breaker for the hose spray be at least 5 feet above the floor to prevent a cross connection. The sink
faucet allows the clinical sink to be used as a service sink for housekeeping purposes.
Figure 14.8
TYPES OF BEDPAN WASHERS
2003 National Standard Pumbing Code-1l/ustrated 321

14.9 LOCAL VENTS AND STACKS FOR CLINICAL SINKS
OR BEDPAN WASHERS
14.9.1 General
Where clinical sinks or bedpan washers have provisions for a local vent, a local vent shall be extended to the
outdoors above the roof. Local vents shall terminate in accordance with Section 12.4. Local vents from
clinical sinks or bedpan washers shall not be connected to vapor vents for sterilizers or to any drainage
system vent.
14.9.2 Material
Local vent piping shall be of a material acceptable for sanitary vents in accordance with Section 3.6.
14.9.3 Required Size and Arrangement

A local vent serving a single clinical sink or bedpan washer shaH be not less than 2" pipe size. Where such
fixtures are instaHed back-to-back or are located above each other on more than one floor, a local vent stack
may be provided to serve multiple fixtures. A 2" local vent stack may serve up to three fixtures. A 3" local
vent stack may serve up to six fixtures. A 4" local vent stack may serve up to twelve fixtures. In multiple
instaHations, the connections to the local vent stack shall be made using sanitary tee or tee-wye fittings
oriented for upward flow from the branch. A branch connection to a local vent stack shall extend not more
than 5 feet horizontally and shaH be sloped not less than 1/4 inch per foot back towards the fixture served.
14.9.4 Provisions for Drainage

Provisions shall be made for the drainage of vapor condensation within local vent piping. A local vent serving
a single fixture may drain back to the fixture served. The base of a local vent stack serving one or more
fixtures shaH be directly connected to a trapped and vented waste branch of the sanitary drainage system.
The trap and waste branch shaH be the same size as the local vent stack. The trap seal depth shall be not less
than 3 inches. The vent for the waste branch shall be 1-1/4" minimum size, but not less than one-halfthe size
of the waste branch.
14.9.5 Trap Priming

The waste trap required under Section 14.9.4 shall be primed by at least one clinical sink or bedpan washer
on each floor served by the local vent stack. A priming line not less than 1/4" OD size shall be extended from
the discharge or fixture-side of the vacuum breaker protecting the fixture water supply to the local vent stack.
A trap having not less than a 3-inch water seal shaH be provided in the priming line. The line shaH prime the
trap at the base of the local vent stack each time that a fixture is flushed.
14.10 STERILIZERS
14.10.1 General
The requirements of this Section apply to sterilizers and bedpan steamers. Such equipment shall be installed in
accordance with this Code and the manufacturer's instructions.
14.10.2Indirect Waste Connections

All waste drainage from sterilizers and bedpan steamers shall be indirectly connected to the sanitary drainage
system through an air gap, in accordance with Chapter 9. Indirect waste pipes shall be not less than the size

of the drain connection on the fixture. Separate waste pipes shall be provided for each fixture, except that up
to three sterilizers may have a common indirect waste pipe if its developed length does not exceed 8 feet. The
size of such common indirect waste pipes shall be not less than the aggregate cross-sectional area of the
individual sterilizer drain connections. Except for bedpan steamers, indirect waste pipes shall not require traps.
14.10.3 Floor Drains

a. A trapped and vented floor drain, not less than 3" pipe size, shall be provided in each recess room or
space where recessed or concealed portions of sterilizers are located. The floor drain shall drain the entire
floor area and shall receive the indirect waste from at least one sterilizer. Where an air gap fitting is provided,
the waste pipe from the fitting may connect to the body of the floor drain above its trap seal.
b. Where required by the sterilizer manufacturer, a floor drain shall be located directly beneath the steril-
izer within the area of its base.
14.10.4 Cooling Required

Waste drainage from condensers or steam traps shall be cooled below 140F before being discharged indi-
rectly to the sanitary drainage system.
14.10.5 Traps Required for Bedpan Steamers

A trap having a minimum seal of 3 inches shall be provided in the indirect waste pipe for a bedpan steamer,
located between the fixture and the air gap at the indirect waste receptor.
14.11 VAPOR VENTS AND STACKS FOR STERILIZERS
14.11.1 General
Where sterilizers have provisions for a vapor vent and such a vent is required by their manufacturer, a vapor
vent shall be extended to the outdoors above the roof. Sterilizer vapor vents shall terminate in accordance
with Section 12.4 and shall not be connected to local vents for clinical sinks or bedpan washers or to any
drainage system vent.
14.11.2 Material
Sterilizer vapor vent piping shall be of a material acceptable for sanitary vents in accordance with Section 3.6.
14.11.3Required Sizeand Arrangement

a. Sterilizer vapor vents and stacks for individual sterilizers shall be not less than the size of the sterilizer
vent connection, except that stacks shall be not less than 1-1/2" pipe size. Where vapor vent stacks serve
more than one sterilizer, the cross-sectional area of the stack shall be not less than the aggregate cross-
sectional areas of the vapor vents for all of the sterilizers served.
b. In single and multiple installations, the connections to the vapor vent stack shall be made using sanitary
tee or tee-wye fittings oriented for upward flow from the branch. A branch connection to a sterilizer vapor
vent stack shall extend not more than 5 feet horizontally and shall be sloped not less than 1/4 inch per foot
away from the sterilizer and toward the vent stack.
14.11.4 Provisions for Drainage

Provisions shall be made for the drainage of vapor condensation within sterilizer vapor vent piping. The base
of stacks shall drain indirectly through an air gap to a trapped and vented waste receptor connected to the
sanitary drainage system.

14.12 DRAINAGE FROM CENTRAL VACUUM SYSTEMS
14.12.1 General
Provisions for drainage from medical, surgical, dental, and similar central vacuum systems shall be as required
by either NFP A 99 - Health Care Facilities or NFP A 99C - Gas and Vacuum Systems. In addition, drainag~
from dental and other vacuum systems that collect fluid waste centrally shall comply with Sections 14.12.2
and 14.12.3.
14.12.2 Positive Pressure Drainage from Air/Waste Separators in Dental Vacuum Systems
a. The waste outlet from an air/waste separator on the discharge side of a vacuum pump or blower shall
be direct-connected to the sanitary drainage system through a deep-seal trap that is conventionally vented
within the plumbing system. The trap vent shall extend vertically to not less than 6 inches above the top of the
separator before making any horizontal turns. The vacuum exhaust air flow from the separator shall be
separately vented to outdoors as required under NFP A 99 and NFP A 99C.
b. The trap and drain branch size shall be at least two pipe sizes larger than the waste pipe from the
separator, but not less than 1-1/2" pipe size. The vent shall be the full size of the trap and drain. The trap seal
shall be at least two times the exhaust backpressure in the separator, but .not less than 4 inches deep.
14.12.3 Gravity Drainage from Waste Holding Tanks in Dental Vacuum Systems
a. The drainage from waste holding tanks shall extend from the vacuum check valve on the waste outlet
ofthe tank and be direct-connected to the sanitary drainage system through a deep-seal trap that is conven-
tionally vented within the plumbing system. In addition, a vent shall be installed between the vacuum check
valve and the drain trap, on the inlet side of the trap, to seal the check valve when the holding tank is operat-
ing under vacuum and collecting waste. This vent shall be connected to the plumbing system vents. Both
vents shall extend vertically to not less than 6 inches above the top of the holding tank before making any
horizontal turns.
b. The trap and drain size shall be at least two pipe sizes larger than the waste outlet and vacuum check
valve, but not less than 2" pipe size. The trap shall be not less than 4 inches deep. The vent for the vacuum
check valve shall be not less than the size of the check valve. The trap vent shall be not less than one-half the
size of the trap and drain branch.
14.13 ASPIRATORS
Provisions for aspirators or other water-supplied suction devices shall be installed only with the specific approval of
the Authority Having Jurisdiction. Where aspirators are used for removing body fluids, they shall include a collec-
tion bottle or similar fluid trap. Aspirators shall indirectly discharge to the sanitary drainage system through an air
gap, in accordance with Chapter 9. The potable water supply to an aspirator shall be protected by a vacuum
breaker or equivalent, in accordance with Sections 14.7 and 10.5.3.

Tests and Maintenance
15.1 EXPOSURE OF WORK

New, altered, extended or replaced plumbing shall be left uncovered and unconcealed until it has been tested and
approved. Where such work has been covered or concealed before it is tested and approved, it shall be exposed
for testing.
15.2 EQUIPMENT, MATERIAL AND LABOR FOR TESTS

Equipment, material and labor required for testing a plumbing system or part thereof shall be furnished by the
installing contractor.
15.3 TESTING OF PLUMBING SYSTEMS
15.3.1 General
New plumbing systems and parts of existing systems which have been altered, extended or repaired shall be
tested as prescribed hereinafter to disclose leaks and defects only when required by the Authority Having
Jurisdiction.
15.3.2 Exceptions
When required by the Authority Having Jurisdiction, where an existing concealed sewer or drain is reused as
part of a new or renovated drainage system, the line shall be traced to its point of termination and shall be
tested to determine that:
1. It is connected to the proper drainage system, such as sanitary or storm,
2. It will withstand a leak test, and,
3. It is free-flowing and not restricted.
15.4 METHODS OF TESTING THE DRAINAGE AND VENT SYSTEMS
15.4.1 RoughPlumbing
Except for outside leaders and perforated or open jointed drain tile, the piping of plumbing drainage and
venting systems shall be tested upon completion of the rough piping installation by water or air and proved
watertight. The Authority Having Jurisdiction may require the removal of any cleanout plugs to ascertain if
the pressure has reached all parts of the system. Either of the following test methods shall be used.
a. The water test shall be applied to the drainage system either in its entirety or in sections after rough
piping has been installed. If applied to the entire system, all openings in the piping shall be tightly closed,
except the highest opening, and the system filled with water to point of overflow. If the system is tested in

sections, each opening shall be tightly plugged except the highest opening of the section under test, and each
section shall be filled with water, but no section shall be tested with less than a 10-foot head of water. In
testing successive sections at least the upper 10 feet of the next preceding section shall be tested, so that no
joint or pipe in the building (except the uppermost 10 feet of the system) shall have been submitted to a test of
less than lO-foot head of water. The water shall be kept in the system or in the portion under test for at least
15 minutes before inspection starts; the system shall then be tight at all points.
b. The air test shall be made by attaching an air compressor testing apparatus to any suitable opening and
after closing all other inlets and outlets to the system, forcing air into the system until there is a uniform gauge
pressure of 5 pounds per square inch or sufficient to balance a column of mercury 10 inches in height. This
pressure shall be held without introduction of additional air for a period of at least 15 minutes.
15.4.2 FinishedPlurnbing
When the rough plumbing has been tested in accordance with section 15.4.1, a final test of the finished
plumbing system may be required to insure that the final fixture connections to the drainage system are gas-
tight.
After the plumbing fixtures have been set and their traps filled with water, their connections shall be tested
and proved gas and watertight. A final smoke or peppermint test shall be required. except in the case of a
previous on site-inspected water or air tested system. If a smoke or peppermint test is required, the following
test methods shall be employed:
a. A smoke test shall be made by filling all traps with water and then reintroducing into the entire system a
pungent, thick smoke produced by one or more smoke machines. When the smoke appears at stack openings
on the roof, they shall be closed and a pressure equivalent to a one-inch water column shall be developed and
maintained for the period of the inspection.
b. A smoke test shall be made by filling all traps with water and then reintroducing into the entire Where
the Authority Having Jurisdiction, due to practical difficulties or hardships, finds that a smoke test cannot be
performed, a peppermint test shall be substituted in lieu thereof. Such peppermint test shall be conducted by
the introduction of two ounces of oil of peppermint into the roof terminal of every line or stack to be tested.
The oil of peppermint shall be followed at once by ten quarts of hot (l40T) water whereupon all roof vent
terminals shall be sealed. A positive test, which reveals leakage, shall be the detection ofthe odor of pepper-
mint at any trap or other point on the system. Oil of peppermint or persons whose person or clothes have
come in contact with oil of peppermint shall be excluded from the test area.
Comment: The smoke or peppermint tests on the finished plumbing can be waived by the Authority
Having Jurisdiction when they are considered to be unnecessary. However, the finished plumbing tests
should be performed if the installation appears to be improper or there is the odor of sewer gas.
15.5 METHOD OF TESTING BUILDING SEWERS

The building sewer shall be tested by insertion of a test plug at the point of connection with the public sewer,
private sewer, individual sewer disposal, or other point of disposal. It shall then be filled with water under a head of
not less than 10 feet. The water level at the top of the test head of water shall not drop for at least 15 minutes.
Where the final connection of the building sewer cannot reasonably be subjected to a hydrostatic test, it shall be
visually inspected.
326 2003 National Standard ?wnbing Code-Illustrated

15.6 METHODS OF TESTING WATER SUPPLY SYSTEMS
Upon completion of a section or the entire water supply system, it shall be tested and proved tight under a water
pressure not less than the working pressure under which it is to be used or 80 pounds per square inch, whichever is
greater.
a. For metallic pipe and where the Authority Having Jurisdiction determines that providing potable water for the
test represents a hardship or practical difficulty, the system may be tested with air to the pressures noted above, as
allowed by the pipe manufacturer.
b. For plastic pipe, testing by compressed gas or air pressure shall be prohibited.
c. Piping shall be disinfected after testing per Section 10.9.
15.7 DEFECTIVE PLUMBING

Where there is reason to believe that the plumbing system of any building has become defective, it shall be sub-
jected to test or inspection and any defects found shall be corrected.
15.8 MAINTENANCE
15.8.1 General
The plumbing and drainage systems shall be maintained at all times in compliance with the provisions of this
Code.
15.8.2 Exception
Existing plumbing installed under prior regulations or lack thereof, may remain unchanged unless immediate
hazards to health, life, or property are evident.

Blank Page

Chapter 16
Regulations Governing Individual Sewage Disposal

Systems for Homes and Other Establishments Where
Public Sewage Systems Are Not Available
16.1 GENERAL PROVISIONS
16.1.1 General
In the absence of State or other local laws governing the installation, use and maintenance of private sewer
disposal systems, the provisions of this Chapter shall apply.
16.1.2 Sewage Disposal

"Sewage disposal" under this section shall mean all private methods of collecting and disposing of domestic
sewage, including septic tanks.
16.1.3 Domestic Sewage

Domestic sewage shall be disposed of by an approved method of collection, treatment and effluent discharge.
Domestic sewage or sewage effluent shall not be disposed of in any manner that will cause pollution of the
ground surface, ground water, bathing areas, lakes, ponds, watercourses, tidewater, or create a nuisance. It
shall not be discharged into any abandoned or unused well, or into any crevice, sink hole, or other opening
either natural or artificial in a rock formation.
Comment: Federal and local environmental agencies have criteriafor the allowable contaminant levels
that can be discharged into a water course or other point of discharge. Improper disposal of sewage can
result in; (1) contamination of public or private water supplies, (2) spread of disease by insects or vermin,
(3) creation of objectionable odors, (4)pollution ofpublic water resources, or (5) other conditions that
are detrimental to public health and safety.
16.1.4 Non-Water-CarriedSewage
When water under pressure is not available, all human body wastes shall be disposed of by depositing them in
approved privies, chemical toilets, or such other installations acceptableto the Authority Having Jurisdiction.
16.1.5 Water-Carried Sewage

Water-carried sewage from bathrooms, kitchens, laundry fixtures and other household plumbing shall pass
through a septic or other approved sedimentation tank prior to its discharge into the soil or into a sand filter.
Where underground disposal or sand filtration is not feasible, consideration shall be given to special methods
of collection and disposal.

16.1.6 Responsibility
The installing contractor is responsible for compliance with these regulations.
16.1.7 Abandoned Disposal Systems

Abandoned disposal systems shall be disconnected from the buildings, pumped out and filled with earth.
Comment: This requirement applies to all abandoned dry wells, septic tanks, cesspools, distribution
boxes, seepage pits, and other structures that have handled sewage or sewage by-products.
16.1.8 Absorption Capacity

No property shall be improved in excess of its capacity to properly absorb sewage effluent in the quantities
and by means provided for in this Code. (See Section 2.19.2.) See Sections 16.5 and 16.6
Comment: The development of properties must be limited by the ability of the soil to absorb the effluent
of the required sewage disposal system. Bacterial action within the soil provitles secondary treatment of
the effluentfrom septic tanks.
16.1.9 Reserved
16.1.10 Higher Compliance

Nothing contained in this Chapter shall be construed to prevent the Authority Having Jurisdiction from requir-
ing compliance with higher requirements than those contained herein where such higher requirements are
essential to maintain a safe and sanitary condition.
16.2 RESERVED
16.3 DESIGN OF INDIVIDUAL SEWAGE SYSTEM
16.3.1 Design
The design of the individual sewage disposal system must take into consideration location with respect to
wells or other sources of water supply, topography, water table, soil characteristics, area available, and
maximum occupancy of the building. See Sections 16.4 through 16.12
Comment #1: The primary factors in the design of private sewage disposal systems are; (1) the location
of the disposal system, (2) the absorption capacity of the soil, (3) the size of the drainagefield, (4) the
size of the septic tank, (5) the elevation of the ground water table, (6) the location of water suppliesfor
the property and neighboring properties, (7) the use and population of the building(s) served, (8) the
topography of the property.
Comment #2: Problems with topography (elevation differences) can be overcome by sewage pumps,
which can pump to elements of the disposal system that are at higher elevations than others.

16.3.2 Type of System
The type of system to be installed shall be determined on the basis oflocation, soil permeability, and ground-
water elevation. See Sections 16.4 and 16.5
16.3.3 Sanitary Sewage

The system shall be designed to receive all sanitary sewage, including laundry waste, from the building.
Drainage from footings or roofs shall not enter the system.
Comment: Storm water andfoundation drains must not be connected to a private sewage disposal
system.
16.3.4 Discharge
The system shall consist of a septic tank discharging into either a subsurface disposal field or one or more
seepage pits or into a combination of both, if found adequate as such and approved by the Authority Having
Jurisdiction. See Figure 1.2.45 and the definitions of "Septic Tank" and "Leaching Well or Pit".
16.3.5 Backflow
Plumbing fixtures connected to a private sewage disposal system that are subject to backflow, shall be
protected by a backwater valve or a sewage ejector.
Comment: Where plumbing fixtures connected to a private sewage disposal system are subject to
backjlow from a blockage in the disposal system, they must be protected by a backwater valve. Sewage
pumps and ejectors having check valvesprovide this protection for thefIXtures that they serve.
16.3.6 Reserved
16.3.7 Design Criteria
Design criteria for sewage flows shall be selected according to type of establishment. (See Table 16.3.7.)

Table 16.3.7
SEWAGE FLOWS ACCORDING TO TYPE OF ESTABLISHMENT
TypeofEstablishment
Schools (toilets and lavatories only) 15 Gal. per day per person
Schools (with above plus cafeteria) 25 Gal. per day per person
Schools (with above plus cafeteria and showers) 35 Gal. per day per person
Day workers at schools and offices ]5 Gal. per day per person
Day camps 25 Gal. per day per person
Trailer parks or tourist camps (with built-in bath) 50 Gal. per day per person
Trailer parks or tourist camps (with central bathhouse) 35 Gal. per day per person
Work or construction camps 50 Gal. per day per person
Public picnic parks (toilet wastes only) 5 Gal. per day per person
Public picnic parks (bathhouse, showers and flush toilets) 10 Gal. per day per person
Swimming pools and beaches 10 Gal. per day per person
Country clubs 25 Gal. per day per person
Luxury residences and estates 150 Gal. per day per person
Rooming houses " 40 Gal.per dayper person
Boarding schools ""'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''' 50 gal. per day per person
Hotels (with connecting baths) 50 Gal. per day per person
Hotels (with private baths-2 persons per room 100 Gal. per day per person
Boardingschools '''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''' I00 Gal. per day per person
Factories (gallons per person per shift-exclusive of
industrial waste) 25 Gal. per day per person
Nursing homes 75 Gal. per day per person
General hospitals 150 Gal. per day per person
Public Institutions (other than hospitals) 100 Gal. per day per person
Restaurants (toilet and kitchen wastes per unit of
serving capacity) 25 Gal. per day per person
Kitchen wastes from hotels, camps, boarding houses, etc.
serving three meals per day 10 Gal. per day per person
Motels 50 Gal. per bed space
Motels with bath, toilet, and kitchen wastes 60 Gal. per bed space
Drive-in theatres 5 Gal. per car space
Stores """""""""""""""""""""""""""'"'''''''''''''''''''''''''''''''''''''' 400 Gal. per toilet room
Service stations 10 Gal. per vehicle served
Airports 3-5 Gal. per passenger
Assembly halls 2 Gal. per seat
Bowlingalleys 75 Gal. per lane
Churches(small) , 3-5 Gal. per sanctuary seat
Churches (large with kitchen) .." 5-7 Gal. per sanctuary seat
Dance halls 2 Gal. per day per person
Laundries (coin operated) 400 Gal. per machine
Service stations 1000 Gal. (First Bay)
, 500 Gal. (Each add. Bay)
Sub-divisionsor individual homes 75 Gal. per day per person
Marinas-Flush toilets 36 Gal. per fixture per hr
Urinals .., ]0 Gal. per fixture per hr
Wash basins """""""""""""""'"'''''''''''''''''''''''''''''''''''''''''''''''' 15Gal.perfixtureper hr
Showers 150 Gal. per fixture per hr

16.4 LOCATION OF INDIVIDUAL SEWAGE SYSTEM
16.4.1 Reserved
16.4.2 Reserved
16.4.3 MinimumDistances
The minimum distances that shall be observed in locating the various components of the disposal system shall
be as given in Table 16.4.3.
Table 16.4.3
MINIMUM DISTANCE BETWEEN COMPONENTS
OF AN INDIVIDUAL SEWAGE DISPOSAL SYSTEM (In Feet))
Single
Shallow Deep Suction Septic Distribution Disposal Seepage Dry Property Building'
Well Well Line Tank Box Field Pit Well Line
Bldg. Sewer
other than
cast-iron 50 50 50
Bldg. Sewer
cast-iron 10 10 10
Septic Tank 100 50 50 - 5 10 10 10 101 10
Distribution
Box 100 50 50 5 - 5 5 10 20
Disposal
Field 100 50 50 10 5 - - - 10 20
Seepage
Pit 100 50 50 10 5 - - - 10 20
Dry Well 100 50 50 10 5 - - - 10 20
Shallow
Well - - - 100 100 100 100 100
Deep
Well - - - 50 50 50 50 50
Suction
Line - - - 50 50 50 50 50
'May be closer to building when permission is given by the Authority Having Jurisdiction
16.4.4 General
All sewage disposal systems shall confonn with the following general principles regarding site:
16.4.4.1 Location
Sewage disposal system shall be located at the lowest point on the premises consistent with the general
layout topography and surroundings, including abutting lots. Locations at a higher elevation through
employment of a forced system may be used with the specific approval of the Authority Having
Jurisdiction.
16.4.4.2 Watersheds
Sewage disposal facilities shall not be located on any watershed for a public water supply system.

16.4.4.3 Septic Tanks and Underground Disposal
Septic tanks and underground disposal means shall not be within 200 feet measured horizontally from
the high water level in a reservoir or the banks of tributary streams when situated less than 3,000 feet
upstream from an intake structure.
16.4.4.4 Beyond 3,000 feet

Sewage disposal facilities situated beyond 3,000 feet upstream from intake structures shall be located
no less than 100 feet measured horizontally from the high water level in the reservoir or the banks of
tributary streams.
16.4.4.5 Percolation Test

Prior to approval, the soil must prove satisfactory by the standard percolation test when underground
disposal is used. See Section 16.5
16.5 PERCOLATION TEST

Percolation tests to detennine the absorption capacity of soil for septic tank effluent shall be conducted in the
following manner:
16.5.1 Subsurface Irrigation

When subsurface irrigation is contemplated, a test pit shall be prepared 2 feet square and not less than I foot
deep. At the time of conducting the percolation test, a hole I foot square and 1 foot deep shall be prepared in
the test pit.
16.5.2 Water Depth

The hole shall be filled with water to a depth of7 inches. For pre-wetting purposes, the water level shall be
allowed to drop 6 inches before time of recording is started.
16.5.3 TimeExpired
The time required for the water level to drop I inch from 6 inches to 5 inches in depth shall be noted and the
length of tile in the subsurface irrigation system shall be obtained from Section 16.5.4. In no case, however,
shall less than 100 feet of tile be installed when 1 foot trenches are used.
16.5.4 Tile Length

The tile lengths for each 100 gallons of sewage per day are as follows:
Time in Minutes The Length for Trench Widths of

for I-inch Drop I-foot 2-feet 3-feet
I 25 13 9
2 30 15 10
3 35 18 12
5 42 21 14
10 59 30 20
15 74 37 25
20 91 46 31
25 105 53 35
30 125 63 42
Comment: Determine the total daily sewageflow for the systemfrom Table 16.3.7. Divide this number
by 100 and determine the required length and number of tiles in the underground disposal system.

16.5.5 Seepage Pits
When seepage pits are contemplated, test pits approximately 5 feet in diameter to permit a man entering the
pit by means of a ladder and to such depth as to reach a porous soil shall be prepared. In the bottom of this
pit, a I foot square by I foot deep hole shall be made at the time of testing and the percolation test conducted
as indicated under Sections 16.5.1, 16.5.2, and 16.5.3. See the definition of "Leaching Well or Pit" and
Figure 1.2.41.
Comment: Observe safety requirements regarding sheeting, shoring, and bracing for deep excavations.
16.5.6 Seepage Pit Absorption Area

The absorption area of a seepage pit required shall be obtained from Table 16.5.6. In no case, however, shall
the absorption area in the porous soil be less than 125 square feet. The bottom of the pit shall not be consid-
ered part of the absorption area.
Comment: The absorption area of a seepage or leaching pit is the square foot area of the sidewalls. The
sidewall area = 3.1416 x diameter x depth (both in feet).
TABLE 16.5.6
REQUIRED ADSORPTION AREA IN SEEPAGE PITS FOR EACH 100 GALLONS OF
SEWAGE PER DAY
Time in Minutes Effective Absorption Area

I for I-inch Drop Square Feet
1 32
2 40
~
.J 45'
5 56
10 75
15 96
20 108
25 139
30 167
16.5.7 Thickness of Porous Soil

The thickness of the porous soil below the point of percolation test must be determined by means of digging a
pit or using a soil auger. The effective absorption area shall be calculated only within this porous soil.
16.6 CAPACITY OF SEPTIC TANKS
16.6.1 LiquidCapacity
The liquid capacity of all septic tanks shall conform to Tables 16.3.7 and 16.6.1 as determined by the number
of bedrooms or apartment units in dwelling occupancies and the occupant load or the number of plumbing
fixture units as determined from Table 11.4.1, (whichever is greater) in other building occupancies.
Comment: The septic tank sizes in Table 16.6.1 have allowancesfor sludge storage space and the use of
domestic food waste disposal units.

Table 16.6.1
CAPACITY OF SEPTIC TANKS
Multiple Other uses; Minimum
Single family dwellings units or maximum septic tank
dwelling-number apartment-one fixture capacity in
of bedrooms bedroom each units served gallons
1-3 20 1000
4 2 units 25 1200
5 or 6 3 33 1500
7 or 8 4 45 2000
5 55 2250
6 60 2500
7 70 2750
8 80 3000
9 90 3250
10 100 3500
Extra bedroom: 150 gallons each.

Extra dwelling units over 10: 250 gallons each.
Extra fixture units over 100: 25 gallons per fixture unit.
16.6.2 Reserved
16.6.3 Multiple Compartment
In a tank of more than one compartment, the inlet compartment shall have a capacity of not less than two-
thirds of the total tank capacity.
Comment: Septic tanks with two compartments operate more efficiently than single-compartment tanks
at removing solids in the efJluent. The liquid that enters the second compartment is already substantially
clarified. There is less turbulence in the second chamber, which permits finer suspended solids to settle
out.
16.6.4 Septic Tank Materials

See Sections 3.3.11, 16.6.5 and 16.6.6.
Comment: Modern septic tanks are typically constructed of concrete (pre-cast),polyethylene, orfiber-
glass. Steel septic tanks are prohibited by many jurisdictions because of leakage due to corrosion.
16.6.5 Steel Tanks
Comment: Steel septic tanks are no longer approved by mostjurisdictions because of leakage due to
corrosion. The average life expectancy of a steel septic tank is only 7years.
16.6.5.1 Welding
All steel tanks shall be continuous welded. (No spot welding is permitted.)
336 2003 National Standard Pumbing Code-/llustrated

16.6.5.2 Wall Thickness
The minimum wall thickness of any steel septic tank shall be No. 12 U.S. gauge (0.109").
16.6.5.3 Coatings
Metal tanks shall be coated inside and out with an approved coating.
16.6.5.4 Baffles
The inlet and outlet baffles shall be at least 12 inches in diameter at the point opposite the opening in
the tank.
16.6.5.5 PumpoutOpening
The pumpout opening in the top shall be large enough to permit a 6-inch cast-iron pumpout pipe to be
inserted with a shoulder to support this pipe.
16.6.5.6 Tank Opening

The tank opening shall not be smaller than 6 inches with a 3-inch collar.
16.6.5.7 Outside Diameter of Collar

Theoutsidediameterofthis collarshallbe 8 inches.
16.6.5.8 PumpoutPipe
The pumpout pipe shall terminate at the surface and a 6-inch iron body brass cleanout shall be caulked
into the hub of this pipe with oakum and molten lead; the cleanout nut shall be solid brass no smaller
than one inch.
16.6.5.9 Manhole
There shall be a 24 x 24-inch manhole held in position by four 3/8" bolts securely welded in place.
16.6.5.10 Partition
There shall be a supporting partition welded in the center ofthese tanks as per drawings.
16.6.5.11 Partition Openings

This partition shall have 2-inch openings at intervals at the top for air circulation.
16.6.5.12 Capacity, Gauge Metal and Weight

The capacity, gauge metal, and weight must be stamped on a brass plate and welded to the top of
metal septic tanks.

16.6.6 Concrete Tanks
16.6.6.1 Baffles
Concrete tanks shall have the same size baffles and pumpout openings as for steel tanks.
16.6.6.2 Tops
The tops shall have a 24-inch manhole with handle to remove same, or be cast in three or four sections
cemented in place.
16.6.6.3 Wall Thickness

The minimum thickness of the walls shall be 2-3/4 inches.
16.6.6.4 Tops and Bottoms

The tops and bottoms shall be 4 inches thick unless placed under a driveway, then they shall be a
minimum of6 inches.
16.6.6.5 Walls and Bottoms

All tank walls and bottoms shall be reinforced with approved reinforcing.
16.6.6.6 TopReinforcing
The tops shall have 3/8 inch steel reinforcing on 6-inch centers.
16.6.6.7 Watertight
The tank shall be watertight.
16.6.7 Depth of Septic Tank

The top ofthe septic tank shall be brought to within 36 inches ofthe finished grade. Where a greater depth is
permitted by the Authority Having Jurisdiction, the access manhole must be extended to the finished grade
and the manhole shall have a concrete marker at grade.
Comment: The typical depth of cover on the top of a septic tank is 12" - 18". Where the depth of cover
exceeds 36", the structural design of the tank must be adequate for the imposed earth loads.
16.6.8 Limitation
No septic tank shall serve more than one property unless authorized by the Authority Having Jurisdiction.
16.6.9 Effluent
The effluent from all septic tanks shall be disposed of underground by subsurface irrigation or seepage pits or
both.
16.7 DISTRIBUTION BOX
16.7.1 When Required

A distribution box shall be required when more than one line of subsurface irrigation or more than one seep-

age pit is used.
Comment: The minimum distancesfrom distribution boxes to the septic tank, disposalfield, seepage pit,
dry well,potable water wells, or suction lines from potable water wells must be in accordance with Table
16.4.3.
16.7.2 Connection
Each lateral line shall be connected separately to the distribution box and shall not be subdivided.
16.7.3 Invert level

The invert of all distribution box outlets shall be at the same level and approximately 2 inches above the
bottom ofthe box. The inlet invert shall be at least 1 inch above the invert of the outlets. The size of the
distribution box shall be sufficient to accommodate the number oflaterallines.
16.7.4 Watertight
The distribution box shall be of watertight construction arranged to receive the septic tank effluent and with
an outlet or connecting line serving each trench or seepage pit.
16.7.5 Baffle
A baffle at least 6 inches high and 12 inches long shall rest on the bottom of the box and be placed at right
angles to the direction of the incoming tank effluent and 12 inches in front of it.
16.7.6 Reserved
16.7.7 Inspection
The sides of the box shall extend to within a short distance of the ground surface to permit inspection, and
shall have a concrete marker at grade.
16.8 SEEPAGE PITS
16.8.1 Use
Seepage pits may be used either to supplement the subsurface disposal field or in lieu of such field where
conditions favor the operation of seepage pits, as may be found necessary and approved by the Authority
Having Jurisdiction. See Figure 1.2.41 and the definition of "Leaching Well or Pit"
16.8.2 Water Table

Seepage pits shall not penetrate the water table.
16.8.3 Septic Tank Effluent Disposal

Where seepage pits are used for septic tank effluent disposal, the number, diameter and depth ofthe pits shall
be determined after percolation tests have been made to ascertain the porosity of the soil. See Section
16.5.5
16.8.4 Excavation
The excavation for a seepage pit shall be greater in diameter than the outside diameter of the vertical
sidewalls to allow for the footing.

16.8.5 AnnularSpace
The annular space between the outside of the vertical walls and the excavation shall be backfilled with broken
stone, coarse gravel, or other suitable material.
16.8.6 Construction
Seepage pits shall be constructed with the bottom being open with an outer ring, or footing, to support the
sidewalls.
16.8.7 Sidewalls
The sidewalls shall be made of pre-cast concrete, stone, concrete or cinder blocks, or brick laid in cement
mortar for strength, with openings at sufficient intervals to permit the septic tank effluent to pass out through
the wall to the surrounding porous soil.
16.8.8 Cover Strength

All septic tank tops and seepage pit covers shall be of sufficient strength to carry the load imposed. Seepage
pit covers shall be at least as required in Sections 16.8.9, 16.8.10, and 16.8.11.
16.8.9 Pre-Cast Top

Seepage pit tops shall be pre-cast, reinforced concrete (2,500 pounds per square inch minimum compressive
strength) not less than 5 inches thick and designed to support an earth load of not less than 400 pounds per
square foot. Each such cover shall extend not less than 3 inches beyond the sidewalls of the pit, shall be
provided with a 6-inch minimum inspection hole with pipe extended to the surface, and a 6-inch cast-iron
standpipe with clean out at grade.
16.8.10 Depth Below Grade

The top shall be at least 36 inches below finished grade, except where less is permitted by the Authority
HavingJurisdiction.
16.8.11 Field Fabricated Slabs

Where field fabricated slabs are used, Table 16.8.11 indicates the requirements.
Table 16.8.11
DESIGN OF SEEPAGE PIT COVERS
Pit Pit Wall Cover Cover Reinforcing Steel Req'd in
Diameter Thickness Thickness Weight Two Perpendicular
Directions
5ft. 4" 5" 1230lb #5 @ 10'h" c/c
6ft. 8" 5" 17701b #5 @ 9" c/c
8ft. 8" 6" 37801b #5 @ 7112"c/c
10ft. 8" 8" 78501b #5@ 6112"c/c

16.9 ABSORPTION TRENCHES
16.9.1 General
Absorption trenches shall be designed and constructed on the basis of the required effective percolation area.
16.9.2 Filter Material

The filter material shall cover the tile and extend the full width of the trench and shall be not less than 6
inches deep beneath the bottom ofthe tile, and 2 inches above the top of the tile. The filter material may be
washed gravel, crushed stone, slag, or clean bank-run gravel ranging in size from 1/2 to 2-1/2 inches. The
filter material shall be covered with burlap, filter cloth, 2 inches of straw, or equivalent permeable material
prior to backfilling the excavation.
16.9.3 AbsorptionField
The size and minimum spacing requirements for absorption fields shall conform to those given in Table 16.9.3.
TABLE 16.9.3
SIZE AND SPACING FOR DISPOSAL FIELDS
Width of Recommended Effective

trench at depth of Spacing tile absorption area
bottom trench lines' per lineal ft. of
(in.) (in.) (ft.) trench (sq. ft.)
18 18 to 30 6.0 1.5
24 18 to 30 6.0 2.0
30 18 to 36 7.6 2.5
36 24 to 36 9.0 3.0
1. A greater spacing is desirable where available area permits.
16.9.4 LateralLength
Length of laterals shall not exceed 100 feet.
Comment: Where the length of lateral tiles in Section 16.5.4 exceeds 100feet, two or more laterals must
be provided.
16.9.5 AbsorptionLines
Absorption lines shall be constructed of 4" pipe of openjointed or perforated vitrified clay pipe, open jointed or
horizontally split or perforated clay tile, perforated bituminized fiber of plastic pipe conforming to approved
standards or open jointed cast-iron soil pipe. In the case of clay tile, open jointed clay pipe, or open jointed
cast-iron soil pipe, the sections shall be spaced not more than 1/2 inch, and the upper half of the joint shall be
protected by asphalt-treated paper while the piping is being covered.

16.9.6 Grade
The trench bottom shall be uniformly graded to slope from a minimum of2 inches to a maximum of 4 inches
per 100 feet.
16.10 RESERVED
16.11 PIPING MATERIAL

See Chapter 3.
Comment: Refer to Section 3.5 and Table 3.5for approved materialsfor drainage piping. Refer to
Section 16.9.5 and Table 3.8for approved materials for sub-soil drainage and absorption lines.
16.12 SAND FILTERS
16.12.1 General Specifications for Design and Construction ofa Sand Filter with Chlorination
16.12.1.1 General
A sand filter shall consist of a bed of clean, graded sand on which septic tank effluent is distributed by
means of a siphon and pipe, with the effluent percolating through the bed to a series of under drains
through which it passes to the point of disposal. See the definition of "Sand Filter" and Figure
1.2.51.
16.12.1.2 FilterSize
The filter size shall be determined on the basis of 1.15 gallons per square foot per day if covered, and
2.3 gallons per square foot per day if an open filter is to be used.
16.12.1.3 Dosing Tank Size

The septic tank effluent shall enter a dosing siphon tank of a size to provide a 2-inch coverage of the
sand filter.
16.12.1.4 Siphon
The siphon shall be of a commercial type and shall discharge the effluent to the sand filter intermit-
tently. The siphon shall be omitted if a pump is used to lift the septic tank effluent to the sand filter.
16.12.1.5 Surge Tank

A surge tank shall be used to receive the pump discharge prior to dosing on the sand filter.
16.12.1.6 Underdrains
Four-inch diameter vitrified clay pipe in 2-foot lengths laid with 1/2 inch openjoints or unglazed farm
tile in I-foot lengths laid with openjoints, with the top half of eachjoint covered with 4-inch wide strips
of tar paper, burlap, or copper screen, or perforated bituminized-fiber pipe or other approved material
shall be used for the underdrains.
16.12.1.7 UnderdrainBed
The underdrains shall be laid at the bottom of the sand filter, surrounded by washed gravel, crushed

stone, slag, or clean bank-run gravel ranging in size from 1/2 inch to 2-1/2 inches and free of fines,
dust, ashes or clay. The gravel shall extend from at least 2 inches below the bottom of the tile to a
minimum of2 inches above the top of the tile.
16.12.1.8 Underdrain Slope and Spacing

The underdrains shall have a slope from 2 inches to 4 inches per 100 feet and shall be placed at 6-foot
to 8-foot intervals.
16.12.1.9 UnderdrainFill
Above the gravel or other material surrounding the underdrain shall be placed 2 feet of washed and
graded sand having an effective size offrom 0.35-0.5 mm and a uniformity coefficient of not over 3.5.
(The effective size of a sand filter is that size of which 10% by weight is smaller and the uniformity
coefficient is the ratio ofthat size of which 60% by weight is smaller to the effective size.)
16.12.1.10 DistributionPipes
The distribution pipes shall be laid at the surface of the sand filter, surrounded by gravel as specified
for the underdrains.
16.12.1.11 Gravel Cover

The gravel should be covered with untreated building paper and the entire area covered with a mini-
mum of 12 inches of earth if the filter is to be covered.
16.12.1.12 Open Filter

If the filter is an open one, the four sides shall be constructed of wood or concrete to prevent earth
erosion from entering the sand filter bed.
16.12.1.13 Chlorine Contact Tank
The chlorine contact tank for disinfection of sand filter effluent shall provide 20 minutes detention at
average flow, but in no case shall it be smaller than 50 gallons capacity. Chlorine control should be
provided by the use of hypochlorite or chlorine machines commercially available.

Blank Page

Potable Water Supply Systems
17.1 GENERAL REGULATION
17.1.1 Jurisdiction
The regulations in this chapter apply to any water system where plumbing fixtures are installed for human
occupancy.
Comment: This chapter applies to private water supply systems serving one or more
buildings independent of any public water supply.
17.1.2 Pumps
Pumps shall be installed only in wells, springs and cisterns that comply with the rules and regulations as
determined by the Authority Having Jurisdiction.
17.2 QUANTITY OF WATER REQUIRED
17.2.1 Single Dwelling Unit

The minimum capacity of the system in gallons per minute shall equal the number of fixtures installed.
Comment: A capacity of 1 GPM per fixture in a single dwelling unit is a rough rule of
thumb. The peak demand should be verified using Tables 10.14.2A and 10.14.2B. See
Section 17.2.4 where well yields do not satisfy the peak demand.
17.2.2 Other Than a Single Dwelling Unit

In other than a single dwelling unit, the water system shall be designed in accordance with Tables 10.14.2A,
and 10.14.2B and shall be capable of supplying the maximum demand to the system according to usage, but,
in no case, less than for a minimum period of 30 minutes.
Comment: See Section 10.14.3 for determining the peak demand on the potable water
supply system.

17.2.3 Available Water
Total water available during any 24-hour period shall not be less than the requirements of Table 16.3.7.
Comment: Table 16.3.7 indicates the daily design sewage flows from various establish-
ments. The available water supply must be able to satisfy this daily volume requirement, as
well as the peak GPM demand.
17.2.4 Secondary Sources of Water

When the available primary source of water does not meet the minimum requirement of Sections 17.2.1,
17.2.2, and 17.2.3, one of the following methods shall be used:
a. Pressure tank of sufficient size.
b. Gravity tank, see Section 10.8.
c. Two pump system.
1. The capacity of the first well pump shall not exceed the well capacity in flow. This pump supplies
water to another tank, which stores the water at atmospheric pressure, and has a control to start and stop the
pump.
2. The second pump delivers the water to a hydropneumatic tank at the required pressure and quantity.
Comment: Where the primary potable water supply source cannot provide sufficient
volume to satisfy the 24-hour demand of the water distribution system, water storage facili-
ties must be provided.
17.3 PRESSURE
Pressure shall be as required in Section 10.14.3.
Comment: Private potable water supply systems must provide adequate pressure for
fixtures to deliver the flow rates for the various fixtures listed in Section 10.14.2.
17.4 PIPING MATERIALS

Piping from the well to inside of the dwelling shall be as required in Section 3.8.
Comment: See Sections 3.4.1 and 3.4.2 for general requirements. See Table 3.4 for
approved materials for water service piping.
17.5 STORAGE TANKS

Storage equipment shall be as follows:
17.5.1 Certified Tanks

All tanks shall be certified under Water Systems Council Standards for size and pressure.
17.5.2 TankMaterial
All tanks shall be coated or made of material to resist corrosion.
346 2003 National Standard ?wnbing Code-Illustrated

17.5.3 Pressure Rating
Hydropneumatic tanks shall have a working pressure rating in excess of the maximum required system
pressure.
17.5.4 Non-Toxic Materials

All tanks shall be constructed of materials and/or coatings which are non-toxic.
17.5.5 Drain Required

All tanks shall be provided with a means for draining.
17.5.6 Covers
Atmospheric storage tanks shall be provided with a cover as required in Section 10.8.
17.6 PUMPS
17.6.1 Certified Pumps

Pumps shall be certified under Water Systems Council Rating and Rating Standards.
Comment #1: Well pumps for private water supplies include shallow well jet pumps, deep
well jet pumps, and submersible pumps.
Comment #2: Jet pumps circulate water through an ejector fitting that develops a vacuum
and draws water from the well. Shallow well jet pumps are used for wells less than 25 feet
deep and have the ejector fitting located outside of the well. De,ep well jet pumps can be
used for wells up to 75 feet deep and have the ejector fitting located within the well casing.
Some jet pumps are convertible and can be used for either one-pipe shallow well or two-pipe
deep well installations, although their rated capacity is less for deep wells than for shallow
wells.
Comment #3: Submersible well pumps are located at the bottom of the drop pipe within the
well casing. Submersible well pumps can lift water up to 500 feet or more.
17.6.2 Installation
Pumps shall be installed in accordance with the manufacturer's recommendations.
17.6.3 EquipmentInstallation
Pumping equipment shall be installed to prevent the entrance of contamination or objectionable material either
into the well or into the water that is being pumped.
17.6.4 Pump Location

The pump shall be located to facilitate necessary maintenance and repair, including overhead clearance for
removal of drop pipe and other accessories.

17.6.5 Pump Mounting
The pump shall be suitably mounted to avoid objectionable vibration and noise, and to prevent damage to
pumping equipment.
17.6.6 Pump Accessories

The pump controls and/or accessories shall be protected from weather.
17.7 PUMP DOWN CONTROL
17.7.1 Tailpipe
30 feet of tailpipe shall be installed below the jet on deep well installation.
17.7.2 Switches
Low pressure cut-off switch and/or water level cut-off switch shall be installed.
17.7.3 Suction Pipe

Use a vertical suction pipe onO-foot length on shallow well jet installation.
17.8 CONTROLS
The following controls are required on all pump installations:
1. Pressure switch
2. Thermal overload switch
3. Pressure relief valve on positive displacement pumps
4. Low water cut-off switch
Low water cut-off switch is required on all pumps that have a capacity in excess ofthe source of water.
17.9 WELL TERMINAL
17.9.1 Upper Well Terminal

Well casing, curbs and pitless adapters shall terminate not less than eight inches above the finished ground
surface or pump house floor and at least 24 inches above the maximum high water level where flooding
occurs. No casing shall be cut off or cut in below ground level except to install a pitless adapter.
17.9.2 Pitless Adapter

17.9.2.1 Design
Pitless adapters designed to replace a section of well casing or for attachment to the exterior of a well
casing shall be constructed of materials which provide strength and durability equal to the well casing.
17.9.2.2 Installation
Installation shall be by threaded, welded or compression-gasketed connection to cutoff casing or
attachment to the exterior wall of the casing and shall be watertight.
17.9.2.3 Adapter Units

Adapter units designed to replace a section of the well casing shall extend above the finished ground
surface as provided in Section 17.9.1. The top of the adapter unit shall be capped with a cover having a
downward flange which will overlap the edge of the unit. The cover shall be securely fastened to the

unit and shall fit sufficiently snug to the unit to be vermin proof. The cover shall provide for watertight
entrance of electrical cables and vent piping or air line if installed.
17.9.3 HandPumps
17.9.3.1 General
Hand pumps shall be of the force type equipped with a packing gland around the pump rod, a delivery
spout which is closed and downward directed, and a one-piece bell type base which is part of the pump
stand or is attached to the pump column in a watertight manner.
17.9.3.2 Installation
The bell base of the pump shall be bolted with a gasket to flange which is securely attached to the
casing or pipe sleeve.
17.9.4 Power Driven Pumps

17.9.4.1 General
The design and operating principles of each type of power driven pump determines where each may be
located with respect to a well. The location selected for the pump determines what factors must be
considered to make an acceptable installation.
17.9.4.2 Location Above Well

Any power driven pump located over a well shall be mounted on the well casing, pipe sleeve, pump
foundation or pump stand such that a watertight closure is or can be made for the open end of the
casing or sleeve.
17.9.4.3 Pump Base

The pump base bolted with a neoprene or rubber gasket or equivalent watertight seal to a foundation or
plate provides an acceptable seal.
17.9.4.4 Large Pump Installation

On large pump installations, the bolting may be omitted when the weight of the pump and column is
sufficient to make a watertight contact with the gasket.
17.9.4.5 Pump LocationOther Than Over Casing

Ifthe pump unit is not located over the casing or pipe sleeve, the pump delivery or suction pipes
emerge from the top of the well, a watertight expanding rubber seal or equivalent shall be installed
between the well casing and piping to provide a watertight closure.
17.9.4.6 Seal Top

The top ofthe seal shall not extend below the uppermost edge ofthe casing or pipe sleeve.
17.9.5 Location inWell For Submersible Pumps

17.9.5.1 General
Thistypeoflocationispermissibleforsubmersiblepumpsonly.

17.9.5.2 Top Discharge Line
When the discharge line leaves the well at the top of the casing, the opening between the dischargeline
and casing or pipe sleeve shall be sealed watertight with an expanding rubber seal or equivalent device.
17.9.5.3 Underground Discharge

When an underground discharge is desired, a properly installed pitless adapter shall be used. A check-
valve shall be installed in the discharge line above the pump in the well.
17.9.5.4 Top Discharge Line Sloped to Drain to Well

When the discharge pipe leaves the well at the top, remains above ground, and slopes to drain back to
the well, the check-valve can be located beyond the well.
17.9.6 Offsetfrom Well

17.9.6.1 Location
Pumps offset from the well, if not located in an above-ground pump house or other building, may be
located in an approved basement provided the pump and all suction pipes are elevated at least 12
inches above the floor.
17.9.6.2 BuriedLines
All portions of suction lines buried below the ground surface between the well and the pump and which
are not enclosed in a protective pipe shall be located the same minimum distance from sources of
contamination as are prescribed for the well in Section 16.4.3.
17.9.6.3 Protective Pipe

When these minimum distances cannot be obtained, the suction line shall be enclosed in a protective
pipe of standard thickness from the well to the pump. The protective pipe shall be sealed watertight at
both ends. This requirement shall be considered satisfied if the suction line lies within a pressure
discharge line.
17.10 VENTS
17.10.1 Size
All vent piping shall be of adequate size to allow equalization of air pressure in the well and shall not be less
than one-half inch in diameter.
17.10.2 Toxic or Flammable Gases

Particular attention shall be given to proper venting of wells and pressure tanks in areas where toxic or
flammable gases are known to be a characteristic of the water. If determined that either of these types of
gases are present, all vents when located in buildings shall be extended to discharge outside of the building at
a height where they will not be a hazard.
17.10.3 Vent Extension

The vent shall extend above the upper terminal ofthe well with the end downturned and covered with not less

than 16 mesh screen wire. The point of entry into the well shall be sealed watertight.
17.11 PUMP BEARING LUBRICATION
17.11.1 General
Lubrication of bearings of power driven pumps shall be with water or oil which will not adversely affect the
quality of the water to be pumped.
17.11.2 Water Lubrication

If a storage tank is required for the lubrication water, it shall be designed to protect the water from contami-
nation.
17.11.3 Oil Lubrication

The reservoir shall be designed to protect the oil from contamination. The oil shall not contain substances
which will cause odor or taste to the water pumped.
17.12 WATER LEVEL MEASUREMENT

On wells oflarge capacity where access for measuring the water level in the well is provided, piping for this
purpose shall terminate above the upper well terminal, be capped or otherwise closed, and all openings around the
piping at the point of entry into the well sealed watertight.
17.13 PROHIBITED PUMPS

No pitcher or chain-bucket pump shall be installed on any water supply.
17.14 PUMP HOUSING
17.14.1 Watertight
A separate structure housing the water supply and pumping equipment shall have an impervious floor and
rain-tight walls and roof.
17.14.2 Pump Pit

A pump pit shall be of watertight construction and provided with a positive drain or sump pump to keep the pit
dry.
17.15 CROSS CONNECTION
17.15.1 Restriction
There shall be no cross-connection between an individual water supply system and other individual or public
water supply system.
17.15.2 Limitations
No water supply shall serve more than one property unless authorized by the Authority Having Jurisdiction.

Blank Page

Mobile Home & Travel Trailer Park
Plumbing Standards
The primary objective of this Chapter is to assure sanitary plumbing installations in trailer home parks. Reference
should be made to the Authority Having Jurisdiction and the regulations promulgated by the Authority Having
Jurisdiction governing the establishment and operation of trailer home parks.
18.1 DEFINITIONS
Comment: The requirements of this chapter are intended as general requirements for parks and
campgrounds that serve travel trailers, recreational vehicles, and mobile homes. Travel trailers and
recreational vehicles are used as temporary dwellings for travel or recreational purposes. Mobile
homes are movable structures or units that are designed as living quarters. The requirements of the
Authority Having Jurisdiction may varyfor the different types of parks and campgrounds.
18.1.1 Service Buildings

A building housing toilet, laundry and other such facilities as may be required.
18.1.2 Sewer Connection

Sewer connection is that portion of the drainage piping which extends as a single terminal under the trailer
coach for connection with the trailer park drainage system.
18.1.3 TrailerCoach
Any camp-car, trailer, or other vehicle with or without motive power, designed and constructed to travel on
the public thoroughfares in accordance with provisions of the Vehicle Code and designed or used for human
habitation.
18.1.4 Trailer Coach, Dependent

One which is not equipped with a water closet for sewage disposal.
18.1.5 Trailer Coach, Independent

One which is equipped with a water closet for sewage disposal.
18.1.6 Trailer Coach Drain Connection

The removable extension connecting the trailer coach drainage system to the trailer connection fixture.

18.1. 7 Trailer Coach, Left Side
The side farthest from the curb when the trailer home is being towed or in transit.
18.1.8 Trailer Connection Fixture

A connection to a trap which is connected to the park drainage system, and receives the water, liquid or other
waste discharge from a trailer coach.
18.1.9 Trailer Park Drainage System

The entire system of drainage piping used to convey sewage or other waste from a trailer connection fixture
to the sewer.
18.1.10 TrailerPark Branch Line

That portion of drainage piping which receives the discharge from not more than two trailer connection
fixtures.
18.1.11 TrailerPark
Any area or tract of land where space is rented or held-out for rent, or occupied by two or more trailer
coaches.
18.1.12 Trailer Park Sewer System

That piping which extends from the public or private sewage disposal system to a point where the first trailer
park drainage system branch fitting is installed.
18.1.13 Trailer Park Water Service Main

That portion of the water distribution system which extends from the street main, water meter, or other
source of supply to the trailer site water service branch.
18.1.14 TrailerSite
That area set out by boundaries on which shall be located one trailer.
18.1.15 Trailer Site Water Service Branch

That portion of the water distributing system extended from the park service main to a trailer site, and in-
cludes connections, devices, and appurtenances thereto.
18.1.16 Water Service Connection

That portion of the water supply piping which extends as a single terminal under the trailer coach for connec-
tion with the trailer coach park water supply system.
18.2 STANDARDS
18.2.1 General
Plumbing systems hereafter installed in trailer home parks shall conform to the provisions set forth in the
preceding chapters of this Code, where applicable, and also to the provisions set forth in this Chapter. Trailer
home park plumbing and drainage systems shall, in addition, conform to all other applicable Authority Having
Jurisdiction regulations.

18.2.2 Plans and Specifications
Before any plumbing or sewerage disposal facilities are installed or altered in any trailer park, duplicate plans
and specifications shall be filed, and proper permits obtained from the Authority Having Jurisdiction. Plans
shall show in detail.
18.2.2.1 Plot Plan

Plot plan of the park, drawn to scale, indicating elevations, property lines, driveways, existing or pro-
posed buildings, and sizes of trailer sites.
18.2.2.2 Plumbing Layout

Complete specifications and piping layout of proposed plumbing system or alteration.
18.2.2.3 Sewerage Disposal Layout

Complete specifications and piping layout of proposed sewer system or alteration.
18.2.2.4 Conformance
Trailer park plumbing system shall be designed and installed in accordance with the requirements of this
Code and shall, in addition, conform to all other pertinent local ordinances and State regulations.
18.2.3 Materials
Materialsshallconformto the approvedstandardsset forthin othersectionsof this Code. See Sections3.4,
3.5, 3.6, and 3.7
18.3 SEWER
18.3.1 Design and Installation

The trailer park drainage system shall be designed and installed in accordance with the requirements of this
Code.
18.3.2 Alternate
The trailer park drainage system may be installed by the use of waste and vent drainage system (See Section
12.17),which shall consist of an installation of waste piping, as hereinafter provided in this Section, in which
the traps for one or more trailer connection fixtures are not separately or independently vented, but which is
vented through the waste piping of such size to secure free circulation of air therein. See Section 12.17 for
combination waste and vent piping systems.
18.3.3 Each Independent Trailer Site

Each independent trailer site shall be provided with a trapped trailer connection which shall consist of a three-
inch horizontal iron pipe-size threaded connection, installed a minimum of three inches and a maximum of six
inches (from the bottom of the connection), above the finished grade. The vertical connection to the trailer
connection fixture shall be anchored in a concrete slab four inches thick, and 18" x 18" square.

18.3.4 AboveGround
Any part ofthe plumbing system extending above the ground shall be protected from damage when deemed
necessary by the Authority Having Jurisdiction.
18.3.5 Trap Connections

Each trailer site shall be provided with a three-inch I.P.S. male or female threaded connection, extended
above the surrounding grade, from a three- inch minimum size vented p-trap.
18.3.5.1 Location
Traps shall be located with reference to the immediate boundary lines of the designated space or area
within each trailer site that will actually be occupied by the trailer. Each such trap shall be located in
the rear third-quarter section along the left boundary line of the trailer parking area not less than one
foot or more than three feet from the road side of the trailer and shall be a minimum of five feet from
the rear boundary of the trailer site. This location may be varied by permission of the Authority Having
Jurisdiction when unusual conditions are encountered.
18.3.5.2 Material
All traps, tail pipes, vertical vents, the upper five feet of any horizontal vent, and the first five feet of
any trap branch shall be fabricated from materials approved for use within a building. See Sections
3.5 and 3.6
18.3.6 Restriction
No vertical pipe shall be used in a special waste and vent system, except the vent pipe, and the connection to
the trailer connection fixture.
18.3.7 Drain Connections

Mobile home and travel trailer drain connections shall be of approved semi-rigid or flexible reinforced hose
having smooth interior surfaces and not be less than a 3-inch inside diameter. Main connections shall be
equipped with a standard quick-disconnect screw or clamp type fitting, not smaller than the outlet. Main
connections shall be gas-tight and no longer than necessary to make the connection between the trailer coach
drain connection and the trailer connector fixture on the site.
18.3.8 Cleanouts
Cleanouts shall be provided as required by Chapter 5 of this Code, except cIeanouts shall be provided in the
vent stacks one foot above grade.
18.3.9 Fixture Unit Loading

For the purpose of determining pipe sizes, each trailer site connection shall be assigned a waste loading value
of six fixture units and each trailer park drainage system shall be sized as provided in Table 18.3.12. Private
sewage disposal shall conform to the requirements of Chapter 16 of this Code. See Table 18.3.12 and
Chapter 16
18.3.10 Slope
Minimumgradeforsewersshallbe sodesignedthata slopesufficienttoprovide ameanvelocityoftwo
feet per secondwhen thepipe isflowingfullorhalf full. See Table K-l in Appendix K

18.3.11 Discharge
The discharge of the park drainage system shall be connected to a public sewer. Where a public sewer is not
available within 300 feet for use, an individual sewage disposal system of a type that is acceptable and
approved by the Authority Having Jurisdiction shall be installed.
Comment: It is preferred that trailerparks be connected topublic sewers, even if more than 300feet
away. Trailer sites are typically densely spaced to maximize the use of the property, which leaves little
space for an adequate on-site sewage disposal system.
18.3.12 MinimumPipeSize
Minimum pipe size of the drainage system shall be as set forth in Table 18.3.12.
Table 18.3.12
DRAIN PIPE SIZING
Max. No. of Trailers, Max. No. of Trailer,
Individually Vented Wet-Vented
Systems Systems Size of Drain
2 1 ~"
.J
30 10 4"
100 50 6"
400 8"
1000 10"
18.4 VENTING
18.4.1 Location
Each wet-vented drainage system shall be provided with a vent not more than 15 feet downstream from its
upper trap, and long mains shall be provided with additional relief vents at intervals of not more than 100 feet
thereafter. The minimum size of each vent serving a wet-vented system shall be as set forth in Table 18.4.1.
TABLE 18.4.1
VENT SIZING
Size of Wet-Vented Drain Minimum Size of Vent

----------------------------------------------------------------------------------------------------------------
~"
.J 2"
4" 3"
5" 4"
6" 5"

18.4.2 Reserved
18.4.3 Reserved
18.4.4 Reserved
18.4.5 Vent Connections
All vent intersections shall be taken off above the center line of the horizontal pipe. All vent stacks shall be
supported by a four-inch by four-inch redwood post, set in at least two feet of concrete extending at least four
inches above the ground, or supported by another approved method.
Comment: Treated lumber is considered to be the equivalent of redwood.
18.4.6 Galvanized Steel Vent Pipe

Galvanized steel vent pipe may extend below the ground vertically, and may directly intersect a drainage line
with an approved fitting, if the entire section around both the drain and the galvanized pipe is encased in
concrete to prevent any movement. Galvanized steel pipe encased in concrete shall be first coated with
bituminous paint, or equivalent protective material.
18.4.7 Location of Vent Pipes

Vent pipes shall be located at least 10 feet above grade and 10 feet from the property line. No vent shall
terminate directly beneath any door, window, or other ventilating openings of the building or of an adjacent
building, nor shall any such vent terminal be within 10 feet horizontally of such opening unless it is at least 2
feet above the top of such opening.
18.4.8 Size of Vent Stack

All vent stacks in the wet-vented system shall be three inches or more in diameter, except that a three-inch
branch line may be vented by a two-inch vent. See Table 18.4.1
18.4.9 Branch Lines

No three-inch branch line shall exceed six feet in length, and no four-inch branch shall exceed 15 feet in
length, unless they are properly vented.
18.4.10 Trailer Connections

Each trailer connection fixture outlet shall be provided with a screw-type plug or cap, and be effectively
capped when not in use.
18.5 WATER DISTRIBUTION SYSTEM
18.5.1 Conformance
Each trailer park water distribution system shall conform to the requirements of Chapter 10 of this Code and
shall be so designed and maintained as to provide a residual pressure of not less than 20 psi at each trailer site
under normal operating conditions. (See Table 10.14.3.) Refer to Appendix B for sizing the water distri-
bution system.

18.5.2 Individual Water Service Branch
Every trailer site shall be provided with an individual water service branch line which shall not be less than 3/
4" in diameter, delivering safe, potable water.
18.5.3 Connection Components

A control valve shall be installed on the water service branch, followed by an approved backflow preventer
in accordance with ASSE 1024 or CSA B64.6 on the discharge side of the control valve, with a pressure
relief valve located on the discharge side of the backflow preventer; with a hose connection or other ap-
proved attachment on the trailer side of the relief valve. Each such pressure relief valve shall be equipped
with a full-size drain with the end of the pipe not more than two feet or less than six inches above the ground
and pointing downward. Such drain may terminate at other approved locations. No part of such drain pipe
shall be trapped. No shut-off valve shall be installed between any such pressure relief valve and the trailer it
serves. The backflow device and relief valve shall be located not less than 12 inches above the grade.
18.5.4 Connection Details

The service connection shall not be rigid. Flexible metal tubing is permitted. Fittings at either end shall be of a
quick disconnect type not requiring any special tools or knowledge to install or remove.
18.5.5 Water Fixture Units

Each trailer outlet on the water distribution system shall be rated as six water fixture units.
18.5.6 Location of Water Connection

The trailer park water outlet for each trailer coach space shall be located near the center of the left side of
each trailer coach.
18.5.7 FireProtection
In the design of the water distribution system in a trailer park, consideration for fire outlet stations throughout
the park should be made relative to the location and quantity of water necessary during an emergency
period.
18.5.8 Backflow Protection

All requirements as described in Chapter 10 of this Code shall be considered a part ofthis Section.
18.6 RESERVED
18.7 TESTING
Installations shall be tested and inspected as required by this Code.
18.8 SANITARY FACILITIES
18.8.1 Public Toilets, Baths, and Lavatories

Public toilets, baths, and lavatories shall be installed and maintained for each sex in accordance with the
following ratio of trailer sites:

18.8.1.1 DependentTrailer
Trailer parks constructed and operated exclusively for dependent trailers shall have one toilet, one
shower, and one lavatory for each 10 sites or fractional part thereof.
Comment: Dependent trailers are not equipped with a water closet and lavatory and are dependant on
the trailer park for such facilities.
18.8.1.2 IndependentTrailer
Trailer parks constructed and operated exclusively for independent trailers shall have one toilet, one
shower, and one lavatory for each 100 sites or fractional part thereof.
Comment: Independent trailers are equipped with a water closet and lavatory and are not dependent on
the trailer park for such facilities.
18.8.1.3 Combined Trailer Use

Trailer parks constructed and operated for the combined use of dependent and independent trailers
shall have facilities as shown in Table 18.8.1.
Table 18.8.1
FACILITIES REQUIRED
Sites Toilets Showers Lavatories
2-25 I 1 I
26-70 2 2 2
18.8.1.4 Additional Toilets

One additional toilet shall be provided for each 100 sites or fractional part thereof in excess of 70 sites.
Comment: Section 18.8.1.4 applies to trailer parks with combined trailer use, as in Section 18.8.1.3.
18.8.2 Exclusivity
Each toilet shall be for the exclusive use of the occupants ofthe trailer sites in the trailer park.
18.8.3 Showers
In every auto and trailer park, shower baths or other bathing facilities with hot and cold running water shall be
installed in separate compartments. Every compartment shall be provided with a self-closing door or other-
wise equipped with a waterproof draw curtain.
360 2003 National Standard Pumbing Code-fIIustrated

18.8.4 LaundryFacilities
Every trailer park shall be provided with an accessory utility building containing at least one mechanical
washing machine or laundry tray equipped with hot and cold running water for every 20 trailer sites or
fractional part thereof, but in no case shall there be less than two laundry trays in any trailer park.
18.8.5 BathingorShowerCompartments
The inner face of walls of all bathing shower compartments shall be finished with cement, concrete, metal, tile
or other approved waterproof materials extending to a height of not less than six feet above the floor. Floors
or shower compartments shall be made of concrete or other similar impervious material. Floors shall be
waterproof and slope 1/4 inch per foot to the drains.
18.9 MAINTENANCE
All required devices or safeguards shall be maintained in good working order. The owner, operator, or lessee of
the trailer park, or his designated agent shall be responsible for the maintenance. When washrooms or toilet rooms
are installed, they must conform with this Code.
18.10 OPERATOR'S RESPONSIBILITY-VIOLATIONS

When it is evident that there exists, or may exist, a violation of any pertinent regulation, the owner, operator, lessee,
person in charge of the park, or any other person causing a violation shall immediately disconnect the trailer water
supply and sewer connection from the park systems and shall employ such other corrective measures as may be
ordered by the Authority Having Jurisdiction.

Blank Page

Appendix A
Sizing Storm
Drainage Systems

A.I Rainfall Rates for Cities
Therainfall ratesin TableA.I, RAINFALLRATESFORCITIES,arebasedon U.S.WeatherBureauTechnicalPaperNo. 40,specifically
Chart 14: IOO-YEARI HOUR RAINFALL (inches) and Chart 7: IOO-YEAR30-MINUTE RAINFALL (inches). The data in Chart 7 were
multiplied by 0.72 to determine the rainfall for a 15-minute period, then multiplied by 4 to establish the corresponding rainfall rate in inches per
hour. The flow rates in gallons per minute (gpm) were established by dividing the inches per hour by 12 to determine cubic feet per hour per
square foot, then multiplying by 7.48 gallons per cubic foot to determine gallons per hour per square foot, then dividing by 60 minutes per hour
to determine the equivalent gallons per minute.
A.2 Roof Drainage

Primary roof drainage systems are sized for a IOO-year,60-minute storm. Secondary roof drainage systems are sized for a more severe 100-year,
I 5-minute storm. The rainfall rates in Table A.I should be used for design unless higher rates are established locally.
A.3 Sizing by Flow Rate

Storm drainage systems may be sized by stormwater flow rates, using the appropriate GPM/SF of rainfall listed in Table A.I for the local
area. Multiplying the listed GPM/SF by the roof area being drained (in square feet) produces the gallons per minute (gpm) of required flow for
each drain inlet. The flow rates (gpm) can then be added to determine the flows in each section ofthe drainage system. Required pipe sizes can
be determined from Table 13.6.1 and Table 13.6.2.
A.4 Sizing by Roof Area

Storm drainage systems may be sized using the roof area served by each section of the drainage system. Required pipe sizes can be determined
from Table 13.6.1 and Table 13.6.2. Using this method, it may be necessary to interpolate between the various listed rainfall rates (inches per
hour). To determine the allowable roof area for a listed size pipe at a listed slope, divide the allowable square feet of roof area for a I" rainfall
rate by the listed rainfall rate for the local area. For example, the allowable roof area for a 6" drain at 1/8" slope with a rainfall rate of3.2 inchesl
hour is 21400/3.2 = 6688 square feet.
A.5 Capacity of Rectangular Scuppers

Table A.5 lists the discharge capacity of various width rectangular roof scuppers with various heads of water. The maximum allowable level
of water on the roof should be obtained from the structural engineer, based on the design of the roof.
Table A.5
DISCHARGE FROMRECTANGULAR SCUPPERS -
GALLONSPER MINUTE
WATERHEAD -
WIDTH OF SCUPPER (Inches)
(Inches) 6 12 18 24 30 36
0.5 6 13 19 25 32 38
I 17 35 53 71 89 107
1.5 31 64 97 130 163 196
2 98 149 200 251 302
2.5 136 207 278 349 420
3 177 271 364 458 551
3.5 339 457 575 693
4 412 556 700 844
NOTES:
I. Table A.5 is based on discharge over a rectangular weir with end contractions.
2. Head is depth of water above bottom of scupper opening.
3. Height of scupper opening should be 2 times the design head.
4. Coordinate the allowable head of water with the structural design of the roof.

TABLE A.I RAINFALL RATES FOR CITIES
PRIMARY SECONDARY
STATES AND CITIES STORM DRAINAGE STORM DRAINAGE
60-MIN DURATION IS-MIN DURATION
IOO-YR RETURN IOO-YR RETURN
IN/HR GPM/SF IN/HR GPM/SF
ALABAMA
Binllingham 3.7 0.038 7.8 0.081

Huntsville 3.3 0.034 7.5 0.078
Mobile 4.5 0.047 10.1 0.105
Montgomery 3.8 0.039 8.4 0.087
ALASKA
Aleutian Islands 1.0 0.010 2.5 0.026
Anchorage 0.6 0.006 1.5 0.016
Bethel 0.8 0.008 2.0 0.021
Fairbanks 1.0 0.010 2.5 0.026
Juneau 0.6 0.006 1.5 0.016
ARIZONA
Flagstaff ? '
-.0 0.024 5.2 0.054
Phoenix 2.2 0.023 4.9 0.05 I
Tucson 3.0 0.031 5.8 0.060
ARKANSAS
Eudora 3.8 0.039 8.6 0.089
Ft.Smith 3.9 0.041 8.9 0.092
Jonesboro 3.5 0.036 7.5 0.078
Little Rock 3.7 0.038 8.6 0.089
CALIFORNIA
Eureka 1.5 0.016 3.7 0.038
Lake Tahoe I.3 0.014 2.9 0.030
Los Angeles 2.0 0.021 4.3 0.045
Lucerne Valley 2.5 0.026 4.3 0.045
Needles 1.5 0.016 3.7 0.038
Palmdale 3.0 0.031 3.7 0.038
Redding 1.5 0.016 3.7 0.038
San Diego 1.5 0.016 3.7 0.038
San Francisco 1.5 0.016 3.5 0.036
San Luis Obispo 1.5 0.016 3.7 0.038
COLORADO
Craig 1.5 0.016 3.5 0.036

Denver 2.2 0.023 4.6 0.048
Durango 1.8 0.019 4.3 0.045
Stratton 3.0 0.03 I 6.6 0.069
CONNECTICUT
Hartford 2.8 0.029 6.6 0.069
New Haven 3.0 0.03 I 7.2 0.075
DELA WARE
Dover 3.5 0.036 7.8 0.081
Rehobeth Beach 3.6 0.037 8.6 0.089
DlSTRJCT OF COLUMBIA
Washington 4.0 0.042 8.6 0.089

FLORIDA
Daytona Beach 4.0 0.042 8.6 0.089

Ft. Myers 4.0 0.042 10.1 0.105
Jacksonville 4.3 0.045 8.6 0.089
Melbourne 4.0 0.042 8.6 0.089
Miami 4.5 0.047 11.5 0.119
Palm Beach 5.0 0.052 11.5 0.119
Tampa 4.2 0.044 10.1 0.105
Tallahassee 4.1 0.043 9.2 0.096
GEORGIA
Atlanta 3.5 0.036 7.8 0.081
Brunswick 4.0 0.042 8.6 0.089
Macon 3.7 0.038 8.1 0.084
Savannah 4.0 0.042 8.6 0.089
Thomasville 4.0 0.042 8.6 0.089
HA W All
Hawaiian Islands (I)
2003 National Standard PUl11bing Code-Illustrated 365

TABLE A.I RAINFALL RA TES FOR CITIES, Continued
PRIMARY SECONDARY
60-MIN DURATION 15-MIN DURATION
IOO-YRRETURN IOO-YRRETURN
IDAHO
Boise 1.0 0.010 ?-
_.J 0.024
Idaho FaIls !.2 0.012 3.2 0.033
Lewiston 1.0 0.010 2.9 0.030
Twin FaIls !.I 0.01 I 2.3 0.024
ILLINOIS
Chicago 2.7 0.028 6.3 0.065
Harrisburg 3.1 0.032 6.9 0.072
Peoria 2.9 0.030 6.6 0.069
Springfield 3.0 0.031 6.6 0.069
INDIANA
Evansville 3.0 0.031 6.9 0.072
Indianapolis 2.8 0.029 6.3 0.065
Richmond 2.7 0.028 6.3 0.065
South Bend 2.7 0.028 6.0 0.062
IOWA
Council Blutfs 3.7 0.038 8.1 0.084
Davenport 3.0 0.031 7.2 0.075
Des Moines 3.4 0.035 7.8 0.08 I
Sioux City 3.6 0.037 7.8 0.08 I
KANSAS
Goodland 3.5 0.036 7.5 0.078
Salina 3.8 0.039 8.6 0.089
Topeka 3.8 0.039 8.6 0.089
Wichita 3.9 0.041 8.9 0.092
KENTUCKY
Bowling Green 2.9 0.030 6.9 0.072
Lexington 2.9 0.030 6.6 0.069
Louisville 2.8 0.029 6.3 0.065
Paducah 3.0 0.031 6.9 0.072
LOUISIANA
Monroe 3.8 0.039 8.9 0.092
New Orleans 4.5 0.047 10.1 0.105
Shreveport 4.0 0.042 9.5 0.099
MAINE
Bangor 2.2 0.023 4.9 0.051
Kittery 2.4 0.025 5.8 0.060
MilJinocket 2.0 0.021 4.3 0.045
MARYLAND
Baltimore 3.6 0.037 8.6 0.089
Frostburg 2.9 0.030 6.6 0.069
Ocean City 3.7 0.038 8.6 0.089
MASSACHUSETTS
Adams 2.6 0.027 6.0 0.062
Boston 2.7 0.028 6.3 0.065
Springfield 2.7 0.028 6.3 0.065
MICHIGAN
Cheboygan 2.1 0.022 4.6 0.048
Detroit 2.5 0.026 5.5 0.057
Grand Rapids 2.6 0.027 5.5 0.057
Kalamazoo 2.7 0.028 6.0 0.062
Traverse City 2.2 0.023 4.9 0.051
MINNESOTA
Duluth 2.6 0.027 6.0 0.062
Grand Forks 2.5 0.026 6.0 0.062
Minneapolis 3.0 0.031 6.9 0.072
Worthington 3.4 0.035 7.5 0.078
MISSISSIPPI
Biloxi 4.5 0.047 10.1 0.105
Columbus 3.5 0.036 7.8 0.081
Jackson 3.8 0.039 8.6 0.089

TABLE A.I RAINFALL RA TES FOR CITIES, Continued
PRIMARY SECONDARY
60-MIN DURATION I5-MIN DURATION
IOO-YRRETURN IOO-YRRETURN
MISSOURI
Independence 3.7 0.038 8.4 0.87
Jefferson City 3.4 0.035 7.8 0.081
St. Louis 3.2 0.033 7.2 0.075
Springfield 3.7 0.038 8. I 0.084
MONTANA
Billings 1.8 0.019 3.7 0.038
Glendive 2.5 0.026 5.8 0.060
Great Falls 1.8 0.019 3.7 0.038
Missoula 1.3 0.014 2.9 0.030
NEBRASKA
Omaha 3.6 0.037 8.1 0.084
North Platte 3.5 0.036 7.5 0.078
Scotts Bluff 2.8 0.029 6.0 0.062
NEVADA
Las Vegas 1.5 0.016 3.5 0.036
Reno 1.2 0.012 2.9 0.030
Winnemucca 1.0 0.010 0 '
_.J 0.024
NEW HAMPSHIRE
Berlin 2.2 0.023 5.2 0.054
Manchester 2.5 0.026 5.8 0.060
NEW JERSEY
Atlantic City 3.4 0.035 8.1 0.084
Paterson 3.0 0.031 6.9 0.072
Trenton 3.2 0.033 7.2 0.075
NEW MEXICO
Albuquerque 2.0 0.021 4.0 0.042
Carlsbad 2.6 0.027 6.0 0.062
Gallup 2.1 0.022 4.9 0.051
NEW YORK
Binghamton 2.4 0.025 5.5 0.057
Buffalo 2.3 0.024 5.2 0.054
New York 3.1 0.032 6.9 0.072
Schenectady 2.5 0.026 5.8 0.060
Syracuse 2.4 0.025 5.2 0.054
NORTH CAROLINA
Ashville 3.2 0.033 7.2 0.075
Charlotte 3.4 0.035 8.1 0.084
Raleigh 4.0 0.042 8.9 0.092
Wilmington 4.4 0.046 9.5 0.099
NORTH DAKOTA
Bismarck 2.7 0.028 6.3 0.065
Fargo 2.9 0.030 6.6 0.069
Minot 2.6 0.027 5.8 0.060
OHIO
Cincinnati 2.8 0.029 6.3 0.065
Cleveland 2.4 0.025 5.5 0.057
Columbus 2.7 0.028 6.3 0.065
Toledo 2.6 0.027 5.8 0.060
Youngstown 2.4 0.025 5.8 0.060
OKLAHOMA
Boise City 3.4 0.035 7.8 0.081
Muskogee 4.0 0.042 9.2 0.096
Oklahoma City 4.1 0.043 9.2 0.096
OREGON
Medford 1.3 0.014 3.2 0.033
Portland 1.3 0.014 3.2 0.033
Ontario 1.0 0.010 0'
_.J 0.024

TABLE A.I RAINFALL RATES FOR CITIES, Continued
PRIMARY SECONDARY
60-MIN DURATION 15-MIN DURATION
100-YR RETURN IOO-YRRETURN
PENNSYLVANIA
Erie 2.4 0.025 5.5 0.057
Harrisburg 2.9 0.030 6.6 0.069
Philadelphia 3.2 0.033 7.2 0.075
Pittsburg 2.5 0.026 5.8 0.060
Scranton 2.8 0.029 6.0 0.062
RHODE ISLAND
Newport 3.0 0.031 7.2 0.075
Providence 2.9 0.030 6.9 0.072
SOUTH CAROLINA
Charleston 4.1 0.043 7.8 0.081
Columbia 3.5 0.036 8.4 0.087
Greenville 3.3 0.034 9.2 0.096
SOUTH DAKOTA
Lemmon 2.7 0.028 6.3 0.065
Rapid City 2.7 0.028 6.3 0.065
Sioux Falls 3.4 0.035 7.5 0.078
TENNESSEE
Knoxville 3.1 0.032 7.2 0.075
Memphis 3.5 0.036 7.5 0.078
Nashville 3.0 0.031 7.2 0.075
TEXAS
Corpus Christi 4.6 0.048 10.7 0.111
Dallas 4.2 0.044 9.5 0.099
EI Paso 2.0 0.021 4.9 0.051
Houston 4.6 0.048 10.7 0.111
Lubbock 3.3 0.034 7.5 0.078
San Antonio 4.4 0.046 9.8 0.102
UTAH
Bluff 2.0 0.021 4.3 0.045
Cedar City 1.5 0.016 3.5 0.036
Salt Lake City 1.3 0.014 2.6 0.027
VERMONT
Bennington 2.5 0.026 5.8 0.060
Burlington 2.3 0.024 5.2 0.054
Rutland 2.4 0.025 5.5 0.057
VIRGINIA
Charlottesville 3.4 0.035 7.8 0.081
Richmond 4.0 0.042 8.9 0.092
Roanoke 3.3 0.034 7.8 0.081
Norfolk 4.0 0.042 9.5 0.099
WASHINGTON
Seattle 1.0 0.010 ?'
_.J 0.024
Spokane 1.0 0.010 2.6 0.027
Walla Walla 1.0 0.010 2.9 0.030
WESTVIRGINIA
Charleston 2.9 0.030 6.6 0.069
Martinsburg 3.0 0.031 7.2 0.075
Morgantown 2.7 0.028 6.3 0.065
WISCONSIN
La Cross 2.9 0.030 6.9 0.072
Green Bay 2.5 0.026 5.8 0.060
Milwaukee 2.7 0.028 6.3 0.065
Wausau 2.5 0.026 5.8 0.60
WYOMING
Casper 1.9 0.020 4.3 0.045
Cheyenne 2.5 0.026 5.5 0.057
Evaston 1.3 0.014 2.9 0.030
Rock Springs 1.4 0.015 3.5 0.036
I. Rainfall rates in Hawaiian Islands vary tram 1.5 in/ltr to 8.0 in/ltr depending on location and elevation. Consult local data.

Appendix B .
Sizing the Building Water

Supply System
B.I GENERAL. 369
B.2 PRELIMINARY INFORMATION 371
B.2.1 General 371
B.2.2 Materials for System . 371
B.2.3 Characteristics of the Water Supply 371
B.2.4 Location and Size of Water Supply Source 372
B.2.5 DevelopedLengthof System ""'"'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''' 372
B.2.6 Pressure Data Relative to Source of Supply " 372
B.2.7 Elevations . 372
B.2.8 Minimum Pressure Required at Highest Water Outlets 372
B.2.9 Provision of Necessary Information on Plans 372
B.3 DEMAND AT INDIVIDUAL OUTLETS 373
Table B.3 MAXIMUM DEMAND AT INDIVIDUAL WATER OUTLETS 373
B.4 RESERVED "'"'''''''''''''''''''''''''' 373
B.5 ESTIMATING DEMAN D 374
B.5.1 Standard Method "'''''''' , 374
B.5.2 Water Supply Fixture Units (WSFU) Assigned to Fixtures """""""""""""""""""""""""""""""""""""'''''''''' 374
Table B.5.2 WATER SUPPLY FIXTURE UNITS (WSFU) AND
MINIMUM FIXTURE BRANCH PIPE SIZES 375
B.5.3 Table B.5.3 WATER SUPPLY FIXTURE UNITS FOR FIXTURE GROUPS """"""""""""'"'''''''''''''''''''''''''' 376
B.5.3 Water Supply Fixture Units for Fixture Groups .." 377
B.5.4 Demand (GPM) Corresponding to Fixture Load (WSFU) """""""""""""""""""""""'"'''''''''''''''''''''''''''''''''''''' 377
Table B.5.4 TABLE FOR ESTIMATING DEMAND (on page 378)
B.5.5 Total Demand Including Continuous Flow 377
B.6 LIMITATION OF VELOCITY 378
B.6.1 Consideration of Velocity in Design 378
B.6.2 Good EngineeringPractice 379
B.6.3 Manufacturers' Recommendationsfor Avoiding Erosion/Corrosion 379
B.7 SIMPLIFIED METHOD FOR SIZING SYSTEMS IN RELATIVELY LOW BUILDINGS 379
B.7.1 AppIication 379
8.7.2 Simplified Method Based on Velocity Limitations 380
B.7.3 Sizing Tables Based on Velocity Limitations ..""""""""""""""""""""""""""""'"'''''''''''''''''''''''''''''''''''''''''''''' 380
B.7.4 Step-by-Step Procedure of Simplified Sizing Method 380
SIZINGTABLESBASEDONVELOCITYLIMITATION """"""'"'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''' 381
Table B.7.3A COPPER AND BRASS PIPE STANDARD PIPE SIZE
(SMOOTH) 381

Table B.7.3B COPPER WATER TUBE, TYPE M (SMOOTH) 381
Table B.7.3C COPPER WATER TUBE, TYPE L (SMOOTH) 381
Table B.7.30 COPPER WATER TUBE, TYPE K (SMOOTH) 381
Table B.7.3E GALVANIZED IRON AND STEEL PIPE, STANDARD
PIPE SIZE (FAIRLY ROUGH) 382
Table B.7.3F SCHEDULE 40 PLASTIC PIPE, (PE, PVC & ABS) (SMOOTH) 382
Table B.7.3G CPVC TUBING SDRII (ASTM 02846) 382
Table B.7.3H SCHEDULE 80 PLASTIC PIPE (PVC, CPVC) (SMOOTH) 382
B.8 ILLUSTRATION OF SIMPLIFIED SIZING METHOD APPLICATION """""'"'''''''''''''''''''''''''''''''''''''''''''''''''''''''''' 383
B.8.1 Example ... ... ... ... ... ... 383
Figure B.8.1 WATER PIPING ISOMETRIC (NO SCALE) (on pages 384 and 385)
B.8.2 Solution 383
Figure B.8.2 WATER PIPING ISOMETRIC (NO SCALE) 386-387
B.8.3 Supplementary Check of Friction Loss in Main Lines and Risers 388
B.8.4 Application to Systems in High Buildings """""""""""""""""""'"'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''' 388
B.9 LIMITATIONOF FRICTION " 388
B.9.1 Basic Criterion 388
B.9.2 Maximum Permissible Friction Loss 388
B.9.3 Basic Design Circuit 389
B.9.4 Friction Loss in Equipment 389
B.9.5 Estimating Pressure Loss in Displacement Type Cold-Water Meters 389
B.9.6 Uniform Pipe Friction Loss '''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''' 390
B.9.7 Equivalent Length of Piping 390
Table 8.9.7A ALLOWANCE IN EQUIVALENT LENGTH OF
PIPE FOR FRICTION LOSS IN VALVES AND
THREADED FITTINGS (NPT Sizes) ""'"'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''' 390
Table 8.9.7B ALLOWANCE IN EQUIVALENT LENGTH OF
TUBE FOR FRICTION LOSS IN VALVES AND
F ITTIN GS (Copper Tubing) 390
B.9.8 Determination of Flow Rates Corresponding to Uniform Pipe
Friction Loss , 391
Flow vs. Pressure Drop Flow Charts for Various Piping Materials 392-398
B.IO DET AILED SIZING METHOD FOR SYSTEMS IN BUILDINGS
OF ANY HEI GHT .., , 399
B.II ILLUSTRATION OF DETAILED SIZING METHOD APPLICATION """"""""""'"'''''''''''''''''''''''''''''''''''''''''''''''''' 400
B.II.I Example ... ... ... ...... ... 400
B.I1.2 Solution 40 I
Table B.II.2 TYPE L COPPER TUBING FOR "FAIRLY SMOOTH" CONDITION 40 I
8.12 SIZING MANIFOLD TYPE PARALLEL WATER DISTRIBUTION SYSTEMS 402
B.12.1 Manifolds 402
Table B.12.1 MANIFOLD SIZING 402
8.12.2 Distribution Lines ... 402
B.13 PLASTIC PIPING SYSTEMS SUITABLE FOR HOT AND COLD WATER DISTRIBUTION 402
B.I3.1 ASTM 02846 ,... 402
B.13.2 ASTM F441 402
B.13.3 ASTM F442 402
B.13.4 ASTM F877 402

B.1 GENERAL
Note that there are two questions regarding water supply to a building: first, total consumption of water (hot or cold
or both) over a period of time, or second, peak flow at any instant oftime. This appendix considers only the second
question.
Proper design of the water-distributing system in a building is necessary to avoid excessive installed cost and in
order that the various fixtures may function properly under normal conditions. The instantaneous flow of either hot
or cold water in any building is variable, depending on the type of structure, usage, occupancy, and time of day.
The correct design results in piping, water heating, and storage facilities of sufficient capacity to meet the probable
peak demand without wasteful excess in either piping or maintenance cost.
For additional information on this subject, the reader is referred to:
National Bureau of Standards Building Materials and Structures Report BMS 65 (1940), Methods of Estimating
Loads in Plumbing Systems, by R. B. Hunter
National Bureau of Standards Building Materials and Structures Report BMS 79 (1941), Water-Distributing
Systems for Buildings, by R. B. Hunter
New York State Division of Housing and Community Renewal Building Codes Bureau Technical Report No.1,
(1964), A Simplified Method for Checking Sizes of Building Water Supply Systems, by Louis S. Nielsen.
B.2 PRELIMINARY INFORMATION
8.2.1 General
The information necessary for sizing the building water supply system is described in B.2.2 through B.2.9.
Correct sizing is contingent upon accuracy and reliability of the information applied. Thus, such information
should be obtained from responsible parties and appropriate local authorities recognized as sources ofthe
necessary information.
8.2.2 Materials for System

Determine what kind or kinds of piping materials are to be installed in the system. This is a matter of selection
by the owner of the building or his authorized representative, who may be the architect, engineer, or contrac-
tor, as the case may be.
8.2.3 Characteristics ofthe Water Supply

The corrosivity and the scale-forming tendency of a given water supply with respect to various kinds of piping
materials is information which most officials, architects, engineers, and contractors in a water district normally
have at their fingertips, as a result of years of experience. For anyone without such experience and knowl-
edge, significant characteristics of the water supply, such as its pH value, CO2 content, dissolved air content,
carbonate hardness, Langelier Index, and Ryznar Index, may be applied to indicate its corrosivity and
scale-forming tendency. The most appropriate source of such information is the local water authority having
jurisdiction over the system supplying the water, or over the wells from which water is pumped from the
underground water table.

B.2.4 Location and Size of Water Supply Source
Location and size of the public water main, where available, should be obtained from the local water author.
ity. Where a private water supply source, such as a private well system, is to be used, the location and size as
designed for the premises should be determined.
B.2.5 Developed Length of System

Information should be obtained regarding the developed length of the piping run from the source of water
supply to the service control valve of the building (i.e., the developed length of the water service pipe as
shown on site plans). Also, determine the developed length of the piping run from the service control valve to
the highest and/or the most remote water outlet on the system. This may be established by measurement of
the piping run on the plans of the system.
B.2.6 Pressure Data Relative to Source of Supply

Maximum and minimum pressures available in the public main at all times should be obtained from the water
authority, as it is the best source of accurate and reliable information on this subject.
Where a private well water supply system is to be used, the maximum and minimum pressures at which it will
be adjusted to operate may be applied as appropriate in such cases.
B.2.7 Elevations
The relative elevations of the source of water supply and the highest water supply outlets to be supplied in the
building must be determined. In the case of a public main, the elevation of the point where the water service
connection is to be made to the public main should be obtained from the local water authority. It has the most
authoritative record of elevations of the various parts ofthe public system, and such elevations are generally
referred to a datum as the reference level, usually related to curb levels established for streets.
Elevation of the curb level directly in front of the building should be obtained from building plans, as such
information is required to be shown on the building site plans. Elevations of each floor on which fixtures are to
be supplied also may be determined from the building plans.
B.2.8 Minimum Pressure Required at Highest Water Outlets

Information regarding the minimum pressure required at the highest water outlets for adequate, normal flow
conditions consistent with satisfactory fixture usage and equipment function may be deemed to be as follows:
15 psi for all water supply outlets at common plumbing fixtures, except for direct supply flushometer valves at
which the minimum required flow pressure shall be considered as 20 psi when supplying floor outlet type
water closets and urinals, and as 25 psi when supplying wall-hung, siphon-jet or blowout type water closets.
For other types of water supplied equipment, the minimum flow pressure required should be obtained from the
manufacturer.
B.2.9 Provision of Necessary Information on Plans

The basis for designing sizes of water supply piping should be provided on plans of the water supply system
when submitted to plumbing plan examiners for proposed installations. Provision of such information permits
the examiner to quickly and efficiently check the adequacy of sizes proposed for the various parts of the
building water supply system.

B.3 DEMAND AT INDIVIDUAL OUTLETS
Maximum possible flow rates at individual fixtures and water outlets have become generally accepted as industry
practice, which have since become maximum rates set by law. Recognized flow rates at individual water outlets
for various types oftypical plumbing fixtures and hose connections are given in Table B.3.
For older faucets, if the applied pressure is more than twice the minimum pressure required for satisfactory water
supply conditions, an excessively high discharge rate may occur. Such rates may cause the actual flow in the
piping to exceed greatly the estimated probable peak demand rate determined in accordance with the standard
method discussed in Section B.5. Such excessive velocity of flow and friction loss in piping may adversely affect
performance and durability of the system.
More recent faucets, however, are equipped with flow limiting devices that control the discharge rate at a nearly
constant value over a large range of pressures.
Where necessary, it is recommended that means to control the rate of supply should be provided in the fixture
supply pipe (or otherwise) wherever the available pressure at an outlet is more than twice the minimum pressure
required for satisfactory supply. For this purpose, individual regulating valves, variable orifice flow control devices,
or fixed orifices may be provided. They should be designed or adjusted to control the rate of supply to be equal to
or less than the maximum rates set by law.
Table B.3
MAXIMUM DEMAND AT INDIVIDUALWATER OUTLETS
Type of Outlet Maximum Demand, (gpm)
Metering lavatory faucet 0.25 gal/cycle
Self-closing lavatory faucet 0.5
Drinking fountainjet 0.75
Ordinary lavatory faucet 2.5
Shower head, 1/2" 2.5
Laundry faucet, 1/2" 2.5
Ballcock in water closet flush tank 3.0
Dishwashing machine (domestic) 4.0
Laundry machine (8 or 16 Ibs.) 4.0
Sink faucet, 3/8" or 1/2" 4.5
Bath faucet, 1/2" 5.0
Hose bibb or sillcock (1/2 ") 5.0
Sink faucet, 3/4" 6.0
1/2" flush valve (15 psi flow pressure) 15.0
1" flush valve (15 psi flow pressure) 27.0
1" flush valve (25 psi flow pressure) 35.0
B.4 RESERVED

B.5 ESTIMATING DEMAND
B.S.l Standard Method

A standard method for estimating the maximum probable demand in building water supply systems has
evolved and become recognized as generally acceptable. In 1923, the fixture unit method of weighting fixtures
in accordance with their load-producing effects was proposed by Roy B. Hunter, of the National Bureau of
Standards. After studying application ofthe method in the design offederal buildings over a period of years,
the method was revised by Hunter in 1940 I, and then recommended for general application. With appropriate
modifications recently made for modern fixtures, the method fills the need for a reliable, rational way to
estimate probable peak demand in water supply systems for all types of building occupancy.
Note that the concept of maximum probable demand is one of probability. We are saying, in effect, that
the calculated flow rate at any point in a water piping system will not be exceeded more than, say, 0.1% of
the time. For most systems designed by the method described herein, the design flow rates are never
reached. Therefore, the method gives a conservative approach that still does not result in wasteful oversizing.
B.S.2 Water Supply Fixture Units (WSFU) Assigned to Fixtures

Individual fixture branch piping should be sized to provide the flow rates listed in Table B.3 for the particular
fixture. Minimum fixture branch pipe sizes are listed in Table B.5.2.
Peak demand in building water supply systems serving multiple fixtures cannot be determined exactly. The
demand imposed on a system by intermittently used fixtures is related to the number, type, time between uses,
and probable number of simultaneous uses of the fixtures installed in the building. In the standard method,
fixtures using water intermittently under several conditions of service are assigned specific load values in
terms of water supply fixture units. The water supply fixture unit (WSFU) is a factor so chosen that the load-
producing effects of different kinds of fixtures under their conditions of service can be expressed approxi-
mately as multiples of that factor. WSFUs for two or more fixtures can then be added to determine their
combined effect on the water supply system.
Values assigned to different kinds of fixtures and different types of occupancies are shown in Table B.5.2.
The total WSFUs represent the fixture's demand on the domestic water service to the building. For fixtures
having both hot and cold water supplies, the values for separate hot and cold water demands are taken as
being three-quarters (3/4) of the total value assigned to the fixture in each case, rounded to the nearest tenth
of a WSFU. As an example, since the value assigned to a kitchen sink in an individual dwelling unit is 1.5
WSFU, the separate demands on the hot and cold water piping thereto are taken as being 1.1 WSFU.
Another consideration, added in 1994, is the nature of the application of the plumbing fixture. Table B.5.2
includes columns for Individual Dwelling Units, More Than 3 Dwelling Units, Other Than Dwelling Units, and
Heavy-Use Assembly. The concept behind these added classifications is that the maximum probable demand
created by plumbing fixtures varies depending on the type of occupancy in which they are installed.
I. National Bureau of Standards Building Materials and Structures Rep0l1 BMS 6, Methods of Estimating Loads in Plumbing Systems. by R. B. Hunter.

'"
c::;,
c::;,
w
~
c'
"
E2..
v, TABLE B.S.2
0;-
" WATER SUPPLY FIXTURE UNITS (WSFU)l AND MINIMUM FIXTURE BRANCH PIPE SIZE FOR INDIVIDUAL FIXTURES
-
'"
"'-
'" Minimum In Individual In 3 or More In Other than In
'"
'"
c:r Branch Dwelling Dwelling Dwelling Heavy-Use
s.
CJq Pipe Size' Units Units Units Assembly
~
1} INDIVIDUAL FIXTURES Hot
Total
Cold Hot Total Cold Hot
:be
Bathtub or Combination Bath/Shower
[ Bidet
'"
'"
"'
"'- Clothes Washer, Domestic
Dishwasher, Domestic
Drinking Fountain or Water Cooler 3/8"
Hose Bibb 1/2"
Hose Bibb, Each Additional 1/2"
Kitchen Sink, Domestic 1/2"
Laundry Sink 1/2"
Lavatory 3/8"
Service Sink Or Mop Sink 1/2"
Shower 1/2"
Shower, Continuous Use 1/2"
Urinal, 1.0 GPF 3/4"
Urinal, Greater Than 1.0 GPF 3/4"
Water Closet, 1.6 GPF Gravity Tank 1/2"
Water Closet, 1.6 GPF Flushometer Tank 1/2"
Water Closet, 1.6 GPF Flushometer Valve 1"
Water Closet, 3.5 GPP Gravity Tank 1/2"
Water Closet, 3.5 GPP Flushometer Valve 1"
Whirlpool Bath or Combination Bath/Shower 1/2"
NOTES: I. The "total" WSFU values for fixtures represent their load on the water service. The separate cold water and hot water supply fixture units for fixtures having both hot
and cold connections are each taken as :y.of the listed total value for the individual fixture.
2. The fixture branch pipe sizes in Table B.5.2 are the minimum allowable. Larger sizes may be necessary if the water supply pressure at the fixture will be too low due
to the available building supply pressure or the length of the fixture branch and other pressure losses in the distribution system.
3. The WSFU values for 3.5 GPF water closets also apply to water closets having flushing volumes greater than 3.5 gallons.
CM
......
tit
~
-.1
0\
TABLE B.5.3-WATER SUPPLY FIXTURE UNITS (WSFU)l FOR GROUPS OF FIXTURES
Totals In Each Group
Individual In 3 or More
Dwellin Units Dwellin Units
Total Cold Hot Total Cold Hot

BATHROOM GROUPS HAVING 1.6 GPF WSFU
WSFU WSFU WSFU WSFU WSFU
TANK-TYPE WATER CLOSETS2
Half-Bath or Powder Room 3.5 3.3 0.8 2.5 2.5 0.4
1 Bathroom Grou 5.0 5.0 3.8 3.5 3.5 3.0
1-1/2 Bathrooms 6.0 6.0 4.5
2 Bathrooms 7.0 7.0 7.0
2-1/2 Bathrooms 8.0 8.0 8.0
3 Bathrooms 9.0 9.0 9.0
Each Additional Y2Bath 0.5 0.5 0.5
Each Additional Bathroom Grou 1.0 1.0 1.0
BATHROOM GROUPS HAVING 3.5 GPF3 Total Cold Hot Total Cold Hot
GRAVITY-TANK WATER CLOSETS WSFU WSFU WSFU WSFU WSFU WSFU
Half-Bath or Powder Room 4.0 3.8 0.8 3.0 3.0 0.4

1 Bathroom Grou 6.0 6.0 3.8 5.0 5.0 3.0
1-1/2 Bathrooms 8.0 8.0 4.5
2 Bathrooms 10.0 10.0 7.0
2-1/2 Bathrooms 11.0 11.0 8.0
3 Bathrooms 12.0 12.0 9.0
Each Additional Y2Bath 0.5 0.5 0.5
'"
a
aVv Each Additional Bathroom Group 1.0 1.0 1.0
~ Total Cold Hot Total Cold Hot

'"
cs"
f2.. OTHER GROUPS OF FIXTURES II WSFU WSFU WSFU WSFU WSFU WSFU
!(>
'"
'"
~
.., Bath Group with 1.6 GPF Flushometer Valve 6.0 6.0 3.8 4.0 4.0 3.0
"'-
'"
" Bath Group with 3.5 GPP Flushometer Valve 8.0 8.0 3.8 6.0 6.0 3.0
'" Kitchen Group (Sink and Dishwasher) 2.0 1.1 2.0 1.5 0.8 1.5
<:>-
~" Laundry Group (Sink and Clothes Washer) 5.0 4.5 4.5 3.0 2.6 2.6
~ NOTES: 1. The "Total WSFU" values for fixture groups represent their load on the water service. The separate cold and hot water supply fixture units for the
~I
:::::
group are each taken as % of the WSFU values for the individual fixtures in the group according to Table B.5.2, but not greater than the "Total WSFU"
~
v, for the group in Table B.5.3, except that the hot WSFU for groups having 3.5 GPF water closets are the same as those having 1.6 GPF water closets.
'"
'"
"
"'-
2. The WSFU values for tank-type water closets apply to gravity tanks and pressurized tanks.
3. The WSFU values for 3.5 GPF water closets also apply to water closets having flushing volumes greater than 3.5 gallons.
B.5.3 Water Supply Fixture Units for Fixture Groups
Table B.5.3 lists water supply fixture unit values for typical groups of fixtures in bathrooms, kitchens, and
laundries in dwelling units. There is more diversity in the use of the fixtures in these groups than is reflected
by WSFU values for the individual fixtures. The "Total WSFU" represents the demand that the group places
on the domestic water service to the building. The separate cold and hot WSFU's for the group are each
taken as % ofthe WSFU values for the individual fixtures in the group according to Table B.5.3, but not
greater than the "Total WSFU" for the group. An exception is that the hot WSFU values for bathroom groups
having 3.5 GPF (or greater) water closets are the same as those having 1.6 GPF water closets, since the hot
WSFU's are not affected by the demand of the water closet.
B.5.4 Demand (GPM) Corresponding to Fixture Load (WSFU)

To determine the maximum probable demand in gallons per minute corresponding to any given load in water
supply fixture units, reference should be made to Table B.5.4, in which the values have been arranged for
convenient conversion of maximum probable demand from terms of water supply fixture units ofload to
gallons per minute offlow. Intermediate values may be interpolated for loads between those shown in Table
B.5.4.
Note in the table that the maximum probable demand corresponding to a given number of water supply fixture
units is generally much higher for a system in which water closets are flushed by means of direct-supply
flushometer valves than for a system in which water closets are flushed by flushometer tanks. The difference
in maximum probable demand between the two systems diminishes as the total number of fixture units ofload
rises. At 1,000 water supply fixture units, the maximum probable demand in both types of systems is the
same, 210 gpm.
Where a part of the system does not supply flushometer water closets, such as in the case with hot water
supply piping and some cold water supply branches, the maximum probable demand corresponding to a given
number of water supply fixture units may be determined from the values given for a system in which water
closets are flushed by flush tanks.
B.5.5 Total Demand Including Continuous Flow

To estimate the maximum probable demand in gpm in any given water supply pipe which supplies outlets at
which demand is intermittent and also outlets at which demand is continuous, the demand for outlets which
pose continuous demand during peak periods should be calculated separately and added to the maximum
probable demand for plumbing fixtures used intermittently. Examples of outlets which impose continuous
demand are those for watering gardens, washing sidewalks, irrigating lawns, and for air conditioning or
refrigeration apparatus.
Note that some continuous-flow outlets may be controlled to be used only during low-flow periods in the
system. Such time-controlled loads should not be added to the maximum probable demand for intermittently
used fixtures, since they will not occur at the same times. In such cases, it will be necessary to consider both
situations and size the piping for the worse case.
2003 National Standard Pumbing Code-1l/ustrated 377

TABLE B.5.4
TABLE FOR CONVERTING DEMAND IN WSFU TO GPM1
WSFU GPM GPM GPM GPM

FlushTanks2 Flush Valves3 WSFU FlushTanks2 Flush Valves3
3 3 120 49 74
4 4 140 53 78
5 4.5 22 160 57 83
6 5 23 180 61 87
7 6 24 200 65 91
8 7 25 225 70 95
9 7.5 26 250 75 100
10 8 27 300 85 110
11 8.5 28 400 105 125
12 9 29 500 125 140
13 10 29.5 750 170 175
14 10.5 30 1000 210 210
15 11 31 1250 240 240
16 12 32 1500 270 270
17 12.5 33 1750 300 300
18 13 33.5 2000 325 325
19 13.5 34 2500 380 380
20 14 35 3000 435 435
25 17 38 4000 525 525
30 20 41 5000 600 600
40 25 47 6000 650 650
50 29 51 7000 700 700
60 33 55 8000 730 730
80 39 62 9000 760 760
100 44 68 10,000 790 790
NOTES: I. This table converts water supply demands in water supply fixture units (WSFU) to required water flow in gallons per minute
(GPM) for the purpose of pipe sizing.
2. This column applies to portions of piping systems where the water closets are the flush tank type (gravity or pressure) or
there are no water closets, and to hot water piping.
3. This column applies to portions of piping systems where the water closets are the flush valve type.
B.6 LIMITATION OF VELOCITY
B.6.1 Consideration of Velocity in Design

Velocity of flow through water supply piping during periods of peak demand is an important factor which
must be considered in the design of building water supply systems. Limitation of water velocity should be
observed in order to avoid objectionable noise effects in systems, shock damage to piping, equipment, tanks,
coils, and joints, and accelerated deterioration and eventual failure of piping from corrosion. (Also see Section
10.14.1)

B.6.2 Good Engineering Practice
In accordance with good engineering practice, it is recommended generally that maximum velocity at maxi-
mum probable demand in supply piping be limited to 8 fps. This is deemed essential in order to avoid such
objectionable effects as the production of whistling line noise, the occurrence of cavitation, and associated
excessive noise in fittings and valves.
Note that this velocity is too great for systems where the flow is continuous, as in the case of recirculated hot
water piping. The continuous flow rate for hot water with modest chemical content should be limited to not
more than 2 fps for such continuous systems. That is, verify that the flow rate in the system as a result of the
circulation pump only does not exceed 2 fps at any point.
It is also recommended that maximum velocity be limited to 4 fps in water supply piping which supply a
quick-closing device, such as a solenoid valve, pneumatic valve, or a quick-closing valve or faucet of the self-
closing, push-pull, push-button, or other similar type. This limitation is necessary in order to avoid excessive
and damaging shock pressures in the piping and equipment when flow is suddenly shut off. Plumbing equip-
ment and systems are not designed to withstand the very high shock pressures which may occur as the result
of sudden cessation of high velocity flow in piping. (Also see Section 10.14.1)
B.6.3 Manufacturers' Recommendations for Avoiding Erosion/Corrosion

Velocity limits recommended by pipe manufacturers to avoid accelerated deterioration of their piping materi-
als due to erosion/corrosion should be observed. Recent research studies have shown that turbulence accom-
panying even relatively low flow velocities is an important factor in causing erosion/corrosion, and that this is
especially likely to occur where the water supply has a high carbon dioxide content (i.e., in excess of 10 ppm),
and where it has been softened to zero hardness. Another important factor is elevated water temperature
(i.e., in excess of 110F).
To control erosion/corrosion effects in copper water tube, and copper and brass pipe, pipe manufacturers'
recommendations are as follows:
(1) Where the water supply has a pH value higher than 6.9 and a positive scale-forming tendency, such as
may be shown by a positive Langelier Index, peak velocity should be limited to 8 fps;
(2) Where the water supply has a pH value lower than 6.9 and may be classified as aggressively corro-
sive, or where the water supply has been softened to zero hardness by passage through a water softener,
peak velocity should be limited to 4 fps; and
(3) The 4 fps velocity limit should be applied to aU hot water supply piping conveying water at a tempera-
ture above 150F because of the accelerated rate of corrosion at higher temperatures.
Note that the above values apply to velocities at maximum probable demand. For continuous flow systems, do
not exceed 2 fps flow rate for the flow produced by the circulator.
B.7 SIMPLIFIED METHOD FOR SIZING SYSTEMS IN

RELATIVELY LOW BUILDINGS
B.7.1 Application
A simplified method for sizing building water supply systems in accordance with the maximum probable
demand load, in terms of water supply fixture units, has been found to constitute a complete and proper
method for adequately sizing the water supply systems of a specific category of buildings. In this category are
all buildings supplied from a source at which the minimum available water pressure is adequate for supplying
the highest and most remote fixtures satisfactorily during peak demand. Included are almost all one- and

two- family dwellings, most multiple dwellings up to at least three stories in height, and a considerable portion
of commercial and industrial buildings oflimited height and area, when supplied from a source at which the
minimum available pressure is not less than 50 psi. Under such conditions, the available pressure generally is
more than enough for overcoming static head and ordinary pipe friction losses, so that pipe friction is not an
additional factor to consider in sizing.
B.7.2 Simplified Method Based on Velocity Limitations

This method is based solely on the application of velocity limitations that are:
(1) Recognized as good engineering practice; and
(2) Authoritative recommendations issued by manufacturers of piping materials regarding proper use of
their products in order to achieve durable performance and avoid failure in service, especially in water areas
where the supply is aggressively corrosive. These limitations have been detailed in Section B.6. (Also see
Section 10.14.1.)
B. 7.3 Sizing Tables Based on Velocity Limitations

To provide a sizing method sufficiently simplified for easy application by plumbing designers, and for plumbing
plan examiners and inspectors to use in checking pipe sizes of building water supply systems, special tables
have been developed. They are presented herewith under the heading SIZING TABLES BASED ON
VELOCITY LIMITATION. These tables show, for velocity limits of 4 fps and 8 fps, the water supply
fixture unit load permissible for each size and kind of pipe in common use. Hence, the tables may be used in
much the same manner as tables currently applied for sizing drainage and vent systems.
An explanation of these tables, and how they were developed, may serve as a guide to users. The first
column lists the nominal pipe sizes, while the second column shows the actual internal pipe diameter as stated
in the applicable ASTM standard for this kind of pipe. Under the heading, "Velocity = 4 fps," the column
headed "Flow" shows the rate of flow, in gallons per minute, calculated for a velocity of 4 fps for each size of
pipe based on the actual internal diameter. The column headed "Friction" shows the amount of pipe friction as
shown for that rate of flow in charts presented later in this Appendix. Between these two columns are
columns A and B which show load values in terms of water supply fixture units. Column A applies to piping
which does not supply flushometer valves. The load values shown in this column were determined as corre-
sponding to the calculated flow rates by using Table B.5.4, selecting values for supply systems predominantly
for flush tanks. Column B applies to piping which supplies flushometer valves.
NOTE: Some designers use pipe size selections so that the pressure drop does not exceed 10 psi/1 00'. If you
elect to use this conservative basis, piping or tubing up to 1" size will not be used at velocities of 8 fps. See
tables for these values.
B.7.4 Step-by-StepProcedure of Simplified SizingMethod

For sizing systems in relatively low buildings, the simplified sizing method consists of the following seven
steps:
1. Obtain all information necessary for sizing the system. Such information should be obtained from
responsible parties and appropriate local authorities recognized as sources of the necessary information. (See
Section B.2.)
2. Provide a schematic elevation ofthe complete water supply system. Show all piping connections in
proper sequence and all fixture supplies. Identify all fixtures and risers by means of appropriate letters,
numbers, or combinations thereof. Identify all piping conveying water at a temperature above 150F, and all
branch piping to such water outlets as solenoid valves, pneumatic valves, or quick-closing valves or faucets.
Provide on the schematic elevation all the necessary information obtained in Step 1. (See Section B.2.9.)
3. Mark on the schematic elevation, for each section of the complete system, the hot and cold water loads
conveyed thereby in terms of water supply fixture units in accordance with Table B.5.2.

SIZING TABLES BASED ON VELOCITY LIMITATION
Velocity = 4 feet per second V elocity 8 feet per second
Nomi"al Actual Flo" Load Load Frietio" Fie", Load Load [','ictioo Fir'" at
Size I.D. (gpml (WSFUI (WFSU) (psi/IOO') (gpml (WSFU) (WSFU) (psiIlOO') 10 psillOO'
(i".) (i".1 q I 2 1'3 q I 2 1'3 (gpm)
Col. A Col.B Col. A Col. B
Table B.7.3A
COPPER AND BRASS PIPE STANDARD PIPE SIZE (SMOOTH)
1/2 0.625 3.8 6.8 7.7 10 24.0 4.6
3/4 0.822 6.6 8 5.0 13.2 18 18.0 9.3
1 1.062 11.0 15 3.7 22.1 34 13.3 18.5
1-1/4 1.368 18.3 27 2.7 36.6 70 21 9.7
1-1/2 1.600 25.1 40 10 2.3 50.1 125 51 8.2
2 2.062 41.6 92 31 1.7 83.2 290 165 6.1
2-1/2 2.500 61.2 180 80 1.3 122.4 490 390 4.9
3 3.062 91.8 330 210 1.1 183.6 850 810 3.9
4 4.000 156.7 680 620 0.8 313.4 1900 1900 2.8
Table B.7.3B
COPPER WATER TUBE, TYPE M (SMOOTH)
3/8 0.450 2.0 9.6 3.9 34.0
1/2 0.569 3.2 6.4 6.3 8 26.0 3.8
3/4 0.811 6.4 8 5.0 12.9 18 18.0 9.5
1 1.055 10.9 15 3.6 21.8 34 13.0 20.0
1-1/4 1.291 16.3 24 2.9 32.6 60 15 10.0
1-1/2 1.527 22.8 35 2.4 45.6 110 38 8.5
2 1.985 38.6 80 26 1.8 77.2 270 140 6.2
2-1/2 2.465 59.5 170 70 1.4 119.0 470 360 5.0
3 2.945 84.9 300 170 1.1 169.9 750 730 4.0
4 3.903 149.3 625 575 0.8 296.7 1750 1750 2.8
Table B.7.3C
COPPER WATER TUBE, TYPE L (SMOOTH)
3/8 0.430 1.8 11.0 3.6 39.0
1/2 0.545 2.9 8.1 5.8 7 29.0 3.2
3/4 0.785 6.0 7 5.3 12.1 17 19.0 8.5
1 1.025 10.3 14 4.0 20.6 30 14.0 17.0
1-]/4 1.265 15.7 0'O 3.0 31.3 55 15 11.0 30.0
1-1/2 1.505 22.2 35 2.5 44.4 100 36 8.7
2 1.965 38.6 80 26 1.8 77.2 270 140 6.2
2-1/2 2.465 59.5 170 70 1.4 119.0 470 360 5.0
3 2.945 84.9 300 170 1.1 169.9 750 730 4.0
4 3.905 149.3 625 575 0.8 298.7 1750 1750 2.8
Table B.7.3D
COPPER WATER TUBE, TYPE K(SMOOTH)
3/8 0.402 1.6 11.0 3.2 36.0
1/2 0.527 2.7 8.2 5.4 6 30.0 3.0
3/4 0.745 5.4 6 5.6 10.9 15 20.0 7.5
I 0.995 9.7 13 4.1 ] 9.4 29 14.0 16.0
1-1/4 1.245 15.2 24 3.1 30.4 55 15 12.0 29.0
1-1/2 1.481 21.5 35 2.6 43.0 97 35 9.0
2 1.985 38.6 80 26 1.8 77.2 270 140 6.2
2-112 2.465 59.5 170 70 1.4 119.0 470 360 5.0
3 2.945 84.9 300 170 1.1 169.9 750 730 4.0
4 3.905 149.3 625 575 0.8 298.7 1750 1750 2.8

SIZING TABLES BASED ON VELOCITY LIMITATION
Velocity = 4 feet per second Velocity = 8 feet per second
Nominal Act"al Flm' Load Load Friction Flo" Load Load Friction Flo" at
Size ID. (gpm) (WSFU) (WFSU) (1',1/100') (gpm) (WSFU) (WSFlJ) (psl/lOO') 10 1',1/100'
I ' 1'3 q I ' 1'3 (gpm)
(In.) (In.) q
CoL A CoLB CoLA CoLB
Table B. 7.3E
GAL V ANNIZED IRON AND STEEL PIPE, STANDARD PIPE SIZE (FAIRLY ROUGH)
1/2 0.622 3.8 8.0 7.6 10 31.0 4.3
3/4 0.824 6.6 6.0 13.3 18 22.0 8.5
I 1.049 10.8 15 4.5 21.5 34 17.0 17.0
1-1/4 1.380 18.6 28 3.4 37.3 75 21 13.0 34.0
1-1/2 1.610 25.4 41 2.8 50.7 125 51 11.0 50.0
2 2.067 41.8 92 32 2.2 83.6 290 165 8.1
2-1/2 2.469 59.6 172 72 1.8 119.3 490 390 6.8
3 3.068 92.1 330 210 1.4 184.3 850 810 5.4
4 4.026 158.7 680 620 1.1 317.5 1900 1900 4.0
Table B.7.3F
SCHEDULE 40 PLASTIC PIPE, (PE, PVC & ABS) (SMOOTH)
1/2 0.622 3.8 7.0 7.6 10 24.0 4.8
3/4 0.824 6.6 8 5.1 13.3 18 17.5 9.5
I 1.049 10.8 15 3.7 21.5 34 13.0 19.0
1-1/4 1.380 18.6 27 2.7 37.3 75 21 9.5
1-1/2 1.610 25.4 41 0 .O
' 50.7 125 5I 8.0
2 2.067 41.8 92 o'0 1.7 83.6 290 165 6.0
2-1/2 2.469 59.6 172 72 1.4 119.3 490 390 4.8
3 3.068 92.1 330 210 1.1 184.3 850 810 3.7
4 4.026 158.7 680 620 0.8 317.5 1900 1900 2.7
Table B.7.3G
CPVC TUBING SDRII (ASTM 02846)
1/2 0.485 2.3 16.6 5.5 65.0
3/4 0.713 4.9 9.9 9.8 40.0
I 0.921 8.3 11 4.6 16.6 25 18.0
1-1/4 1.125 12.4 3.5 24.8 40 14.0
1-1/2 1.329 17.3 26 2.8 34.6 69 19 11.0
2 1.739 29.6 51 13 2.1 59.2 171 72 8.4
Table B.7.3H
SCHEDULE 80 PLASTIC PIPE (PVC,CPVC)(SMOOTH)
1/2 0.546 2.9 6.9 5.8 27.6
3/4 0.742 5.4 4.8 10.8 15 19.0
I 0.957 9.4 12 3.4 18.8 23 13.6
I 1/4 1.278 16.0 24 2.4 32.0 58 17 9.6
I 1/2 1.500 22.0 34 2.0 44.1 100 36 8.0
2 1.939 36.8 73 23 1.5 73.6 250 120 6.0
NOTE: Column A is f(J[ systems without tlushometer values.

Column B is for systems serving tlushometer values.

4. Mark on the schematic elevation, adjacent to all fixture unit notations, the demand in gallons per minute
corresponding to the various fixture unit loads in accordance with Table B.5.3.
5. Mark on the schematic elevation, for appropriate sections of the system, the demand in gallons per
minute for outlets at which demand is considered continuous, such as outlets for watering gardens, irrigating
lawns, air conditioning apparatus, refrigeration machines, and similar equipment using water at a relatively
continuous rate during peak demand periods. Add the continuous demand to the demand for intermittently
used fixtures, and show the total demand at those sections where both types of demand occur. (See Section
B.5.4.)
6. Size all individual fixture supply pipes to water outlets in accordance with the minimum sizes permitted
by regulations. Minimum fixture supply pipe sizes for typical plumbing fixtures are given in Table B.5.2.
7. Size all other parts of the water supply system in accordance with velocity limitations recognized as
good engineering practice, and with velocity limitations recommended by pipe manufacturers for avoiding
accelerated deterioration and failure of their products under various conditions of service. (Sizing tables based
on such velocity limitations and showing permissible loads in terms of water supply fixture units for each size
and kind of piping material have been provided and may be applied in this step.) (See Section B.6.)
B.8 ILLUSTRATION OF SIMPLIFIED SIZING METHOD APPLICATION
B.8.! Example
A three-story, nine-family multiple dwelling fronts on a public street and is supplied by direct street pressure
from a public main in which the certified minimum pressure is 50 psi. The building has a full basement and
three above-grade stories, each of which is 10' in height from floor to floor. The first floor is 2' above the
curb level in front of the building. The public water main is located under the street: 5' out from and 4'
below the curb.
On each of the above-grade stories there are three dwelling units. Each dwelling unit has a sink and dish-
washer, tank-type water closet, lavatory, and bathtub/shower combination.
The basement contains two automatic clothes washing machines, two service sinks, and a restroom with a
flush-tank water closet and lavatory.
Two lawn faucets are installed, one on the front of the building and one in the rear.
Hot water is to be supplied from a central storage-tank water heater.
The water supply to the building will be metered at the water service entry point to the building.
An isometric drawing of the water piping layout is shown in Figure B.8.l.
B.8.2 Solution
1. All information necessary to develop the design must be obtained from appropriate sources.
2. After the information is known, the isometric drawing (Figure B.8.l) is marked up with general water
supply information, and the mains, risers, and branches are suitably identified.
3. The water supply fixture unit loads are marked on the drawing next to each section of the system.
These values are obtained from Tables B.5.2 and B.5.3. Many designers use parentheses marks for WSFU
to distinguish them from gpm values.
4. The maximum probable demand in gpm is marked on the drawing for each section next to the WSFU
values. These values are obtained from Table B.5.4, using the columns for flush-tank systems.
5. Where sections of the piping serve more than one hose bibb, each additional hose bibb adds a demand
of 1.0 WSFU to the piping. Wherever a section of piping serves a single hose bibb, it adds a demand of 2.5
WSFU.

~
QO DESIGN BASIS
~ Figure B.8.l WATER PIPING ISOMETRIC
PIPING
COPPER WATER TUBING

TYPE L, WITH WROUGHT
FITTINGS & LEAD-FREE SOLDER
WATER SERVICE SIZING (for 3 or more dwellings)
PUBLIC WATER SUPPLY Fixtures Qty WSFU Total
10' main, 50 PSI MIN. PRESSURE Bathroom Groups (1.6 GPF Tanks) 9 3.5 31.5
Kitchen Groups (Sink/DW) 9 1.5 13.5
WATER CHARACTERISTICS 2.5 5.0
Clothes Washers 2
NO SIGNIFICANT FOULING
OR CORROSION AGENTS Service Sinks 2 3.0 6.0
Half Bath I 2.5 2.5
ELEVATIONS Hose Bibb I 2.5 2.5
CURB AS DATUM 10.00' 1.0
Hose Bibb, each additional 1 1.0
WATER MAIN 6.00'
BASEMENT FLOOR 2.00' TOTAL WSFU 62.0
FIRST FLOOR 12.00' Demand (GPM) 33.6
SECOND FLOOR 22.00'
THIRD FLOOR 32.00'
HIGHEST OUTLET 35.00'
MINIMUM OUTLET PRESSURE

15 PSI REQUIRED
WATER SUPPLY FIXTURE UNITS
VELOCITY LIMITATIONS
8 FPS EXCEPT 4 FPS FOR BRANCHES Piping Serving Fixtures Piping Serving Fixtures
TO QUICK-CLOSING YAL YES (*) FIXTURES In 1 or 2 Dwellings In 3 or more Dwellings
Total Cold Hot Total Cold Hot
LENGTH OF RUN TO FARTHEST (5.0) (5.0) (3.8) (3.5) (3.5) (3.0)
Bath Group (\.6 GPF Tank)
& HIGHEST OUTLET
MAIN - A: 50' Half Bath (1.6) GPF Tank) (3.5) (3.3) (0.8) (2.5) (2.5) (0.4)
tv
a A-B: 12' Clothes Washer (4.0) (3.0) (3.0) (2.5) (1.9) (1.9)
a
w B-C: 8' Kitchen Group (Sink/DW) (2.0) (1.1) (2.0) (1.5) (0.8) (1.5)
~c'
C-D:
D-E:
10'
8'
Service Sink (3.0) (2.3) (2.3) (3.0) (2.3) (2.3)
'" Hose Bibb (2.5) (2.5)
~ E- F: 8' (2.5) (2.5)
~
"'" F-G: 10' Hose Bibb, Each Additional (1.0) (1.0) (1.0) (1.0)
!}
"
G-H: 4' Water Closet (1.6 GPF Tank) (2.5) (2.5) (2.5) (2.5)
"- H-I: 10' (0.8) (0.8) (0.5) (0.4) (0.4)
Lavatory (1.0)
"'t I -J: 10'
'"
c;,. J -K: 10'
Bath/Shower (4.0) (3.0) (3.0) (3.5) (2.6) (2.6)
~. TOTAL: 140' PLUS FITTING ALLOWANCE
(j
a HOT WATER TEMPERATURE
f} 140F WITH TANK THERMOSTAT
:k AS CONTROLLER
r;
~
"
"-
'"
a
a 0<>+
w KITCHEN
~
0'
~t-~:\)1~ ST~CK##S
;::s
E2..
-
S?
) (
!::)
~ B TCHEN ~ ) I STACK' (0.8

<p--<"
:rTHROOM BATHROOMIKI3 (3.5).1'-0) 4 "iK I
,
~ ~CK #2 ST~CK ## LAWN DW
""1;j
"
~ j ~'*''''
i
3!
eo- J..! .'.5)
~'
...#.'6'"~ ~
~ ~
(3.5}(300)~ #.::t
V
...~ /FAUCET MI
' :;,
f) ovtt-
~~+
":<f (0.8) (1
~ ,..A" II
R;-
(3.5)
:b
;:, i' * I
~~ ~I <-.~ 'J
'"
'"
!::)
KITCHEN (O ~1.5)
". ,
..' ~t+~~~
.1
t
..!!
J
&
~ STACK#! I ~~ ">1
"'-
~ \>'Ii ~
,l,
~t-~~~~!
How* ~
,1
I
1
;.
~/~~
,,!II "'" 1>"',v;>..:"
C' jV
G
4" ~ fIr.' :--.111
'"
I I DVf ...~iI
'J'i '!o~"*"v-c~v
~ .;
,~Q5) " j))
..o.'~~
~
~$\'
'!o\~~ "
/'"
."
... 4) li.51
V'"'; 1
/~~
CJsr~
oJ)
~~ ~~fJI
- b"E
.~"'~\"' .
~
~;
~~v Il~~6 LEGEND
-
LAWN /(, ",,- Ii ,,) \)0
FAUCET(1.0) :I.~"' . "" 0>"'\""S ~~"*"
~...,.. ~.\\'"' BASIC DESIGN CIRCUIT
0.)"'\
'-1~
~~\"'~)"' Q>"'
-- (HOT OR COLD)
COLD WATER
HOT WATER
'it s~"*"V
(~
W~TER
- ~{JaR
Figure B.S.1 WATER PIPING ISOMETRIC
(NO SCALE)
~
CO
01
Figure B.8.2
W A TERPIPING ISOMETRIC
PRESSURE DROP TO FARTHEST &: HIGHEST OUTLET
SECTION WSFU FLOW LENGTH PIPE PD PRESSURE

(1) (gpm) (feet) SIZE Psi/100ft DROP
MAIN-A 62.0 33.6 50 1-1/2" 4.7 2.4

A-B 62.0 33.6 12 1-1/2" 4.7 0.6
B-C 49.3 28.7 8 1-1/4" 7.0 0.6
C-D 44.8 26.9 10 1-1/4" 6.8 0.7
D-E 38.7 24.4 8 1-1/4" 5.6 0.4
E-F 29.7 19.8 8 1" 10.5 0.8
F-G 13.5 10.3 10 3/4" 13.5 1.4
G-H 4.5 4.3 4 3/4"(4) 2.7 0.1
H-I 4.5 4.3 10 3/4" (4) 2.7 0.3
I-J 4.0 (2) 4.0 10 3/4"(4) 2.3 0.2
J-K 2.0 (2) 4.0 (3) 10 3/4" (4) 2.3 0.2
Total Pipe Pressure Drop 7.7 psi

Fitting Allowance (50% of pipe loss) 3.9 psi
Total Pressure Drop Due to Pipe Friction: 11.6 psi
NOTES:
(1) WSFU s for sections of piping serving fixtures in 3 or more dwellings except as noted.
(2) Water supply fixture units for sections of piping serving fixtures in 1 or 2 dwelling units.
(3) Water flow (gpm) for dishwasher.
(4) Velocity limited to 4 fps because of dishwashers and quick-closing sink faucets.
Minimum Pressure at Water Main = 50.0 psi

Water Meter Pressure Drop = 3.0 psi
Total Pipe Friction Losses = 11.6 psi
Elevation Pressure Drop = (35ft-5ft)(0.433) = 12.6psi
Pressure Available at Location K= 50.0- 3.0-11.6 -12.6 = 22.8 psi
Required Pressure at K = 15 psi
Therefore, pipe sizing is satisfactory.
If this calculation had shown that the pressure drop was excessive, it would be necessary to examine the design
for sections that had the highest drops and then increase those segment sizes.

'"
""
""
IN
~
c.
'"
e..
~
'" KITCHEN
~ ~.&+
Co"""~ STACK ##5
l I Kw*
....
""-
'I STACK .~
'"t>
"
'" (3.0) ##4 ~.;:,::<f
8)
<:>--
,
~.
b' ~TIIROOM
~CK" BATBROO
ST~~CHEN (3.5) 1 "'F"UCET ~(&
*
~
:b
~
'"
~ ~ -/."'"
~
..."'~
~'-I
... #~ 110
..~"''''''1
I 1,
< 1>"'"
II
H
'I.S)
J
[ G
1
KITCHE ' .,(I.$) " ~.I,.G) ..
(0.0) (I
...'\+-~.
.* (18)&'"
~ .1 '" ..
STACK::. (0.8) I ~cP.1 ~ I I
,
/
~
l H
I
"'" ...""':~
G
~ I
I
1.#
~~~~",/",Y,''"Y;;'_''i:>~
~ ,..r1", ~
.~~ ~,",~("7~~; G "J
'r.'"
I
.,...,1, '"
I 1;1
..' ...OJ. ,,~)
I .. :.T... ~..
~~
~
,
<F U' '-.f:! ~.P': ... ,.>
--
~ ~~
<1i !'t "~ ~,\"t"-P.

~O ,~~
-
--
LEGEND
BASICDESIGNCIRCUIT
(HOT OR COLD)
COLDWATER
HOTWATER
r
'AUa:r~ B ' ~~
~
~
~.....:I ","
\Y~
~ \f-5"'""'"
<!t. W A ER ...:.~ -0;>"'
<1>"'
T~
~~
~ .J!!}TER TER
_~METER
Figure B.8.2 WATER PIPING ISOMETRIC
(NO SCALE)
~
00
-..J
6. All individual fixture supply pipes to water outlets are sized in Figure B.8.1 in accordance with the
minimum sizes shown in Table B.5.2.
7. All other parts of the system are sized in accordance with the velocity or pressure limitations estab-
lished for this system as the basis of design. Piping is sized in accordance with the maximum probable
demand for each section of the system. Sizing is done using Table B.7.3A through Table B.7.3H, and
specifically the tables dealing with Copper Water Tube, Type K for sizing the water service pipe; and with
Copper Water Tube, Type L, for sizing piping inside the building since these are the materials of choice as
given in the general information on the drawing.
B.8.3 Supplementary Check of Friction Loss in Main Lines and Risers

A supplementary check ofthe total friction loss in the main lines and risers is made for the longest run of
piping from the public water outlet to be sure that the sizes determined were adequate. This run has been
shown in heavy lines with letters noted at various points.
The sum of all friction losses due to flow through pipe, valves, and fittings is found to be 17.9 psi, whereas the
amount of excess pressure available for such friction loss is 19.4 psi. Thus, the sizes determined on the basis
of velocity limitations exclusively are proven adequate. Checking offriction loss in this case is performed
following steps 8 through 15 of the Detailed Sizing Method for Building of Any Height presented in Section
B.I0. The calculations are shown on Figure B.8.2.
B.8.4 Application to Systems in High Buildings

This method of sizing, based upon the velocity limitations which should be observed in design of building water
supply systems, has much broader application than just to systems in one-, two-, and three-story buildings
where ample excess pressure is available at the source of supply. These velocity limitations should be ob-
served in all building water supply systems. Thus, the sizes determined by this method are the minimum sizes
recommended for use in any case. Where pipe friction is an additional factor to be considered in design,
larger sizes may be required.
B.9 LIMITATION OF FRICTION
B.9.1 Basic Criterion

The design of a building water supply system must be such that the highest water outlets will have available,
during periods of peak demand, at least the minimum pressure required at such outlets for satisfactory water
supply conditions at the fixture or equipment.
B.9.2 Maximum Permissible Friction Loss

The maximum allowable pressure loss due to friction in the water lines and risers to the highest water outlets
is the amount of excess static pressure a~ove the minimum pressure required at such outlets when
no-flow conditions exist. This may be calculated as the difference between the static pressure existing at the
highest water outlets during no-flow conditions, and the minimum pressure required at such outlets for satis-
factory supply conditions.
Where water is supplied by direct pressure from a public main, to calculate the static pressure at the highest
outlet, deduct from the certified minimum pressure available in the public main the amount of static pressure
loss corresponding to the height at which the outlet is located above the public main (i.e., deduct 0.433 psi
pressure for each foot of rise in elevation from the public main to the highest outlet).

Where supplied under pressure from a gravity water supply tank located at an elevation above the highest
water outlet, the static pressure at that outlet is calculated as being equal to 0.433 psi pressure for each foot
of difference in elevation between the outlet and the water level in the tank. In this case, the minimum static
pressure at the outlet should be determined as that corresponding to the level of the lowest water level at
which the tank is intended to operate.
B.9.3 Basic Design Circuit

Of all the water outlets on a system, the one at which the least available pressure will prevail during periods
of peak demand is the critical outlet which controls the design. Normally, it is the highest outlet which is
supplied through the longest run of piping extending from the source of supply.
This circuit is called the Basic Design Circuit (BDC) for sizing the main water lines and risers.
In most systems, the BDC will be found to be the run of cold water supply piping extending from the source
of supply to the domestic hot water vessel plus the run of hot water supply piping extending to the highest and
most remote hot water outlet on the system. However, in systems supplied directly from the public main and
having flushometer-valve water closets at the topmost floor, the BDC may be found to be the run of cold
water supply piping extending from the public main to the highest and most remote flushometer valve on the
system.
B.9.4 Friction Loss in Equipment

Where a water meter, water filter, water softener, fish trap or strainer, or instantaneous or tankless water
heating coil is provided in the BDC, the friction loss corresponding to the maximum probable demand through
such equipment must be determined and included in pressure loss calculations. Manufacturers' charts and
data sheets on their products provide such information generally, and should be used as a guide in selecting
the best type and size of equipment to use with consideration for the limit to which pressure loss due to
ftiction may be permitted to occur in the BDC. The rated pressure loss through such equipment should be
deducted from the friction loss limit to establish the amount of pressure which is available to be dissipated by
friction in pipe, valves, and fittings of the BDC.
B.9.5 Estimating Pressure Loss in Displacement Type Cold-Water Meters

The American Water Works Association standard for cold-water meters of the displacement type is desig-
nated AWW A C 700-64. It covers displacement meters known as nutating- or oscillating-piston or disc
meters, which are practically positive in action. The standard establishes maximum capacity or delivery
classification for each meter size as follows:
5/8" 20 gpm
3/4" 30 gpm
1" 50 gpm
1-1/2" 100gpm
2" 160gpm
3" 300 gpm
Also, the standard establishes the maximum pressure loss corresponding to these maximum capacities as
follows:
15 psi for the 5/8", 3/4" and 1" meter sizes
20 psi for the 1-1/2",2",3",4" and 6" sizes.

B.9.6 Uniform Pipe Friction Loss
To facilitate calculation of appropriate pipe sizes corresponding to the permissible friction loss in pipe, valves,
and fittings, it is recommended that the BDC be designed in accordance with the principle of uniform pipe
friction loss throughout its length. In this way, the friction limit for the piping run may be established in terms
of pounds per square inch per 100 feet of piping length. The permissible uniform pipe friction loss in psi/1 00' is
calculated by dividing the permissible friction loss in pipe, valves, and fittings by the total equivalent length of
the basic design circuit, and multiplying by 100.
B.9.7 Equivalent Length of Piping

The total equivalent length of piping is its developed length plus the equivalent pipe length corresponding to the
frictional resistance of all fittings and valves in the piping. When size of fittings are known, or has been
established in accordance with sizes based upon appropriate limitation of velocity, corresponding equivalent
lengths may be determined directly from available tables. Two such tables, one for pipe of standard pipe size
and a second for copper water tube, are presented herewith. See Tables B.9.7A and B.9.7B.
As a general finding, it has been shown by experience that the equivalent length to be allowed for fittings and
valves as a result of such calculations is approximately fifty percent of the developed length of the BDC in
the case of copper water tube systems, and approximately seventy-five percent for standard threaded pipe
systems.
TABLE B.9.7A
ALLOWANCE IN EQUIVALENT LENGTH OF PIPE FOR FRICTION
LOSS IN VALVES AND THREADED FITTINGS-NPT Sizes
Equivalent feet of pipe for various sizes
Fitting or Value 1/2" 3/4" I" 1 1/4" 1 1/2" 2" 2 112" 3"
45" elbow 1.2 1.5 1.8 2.4 3.0 4.0 5.0 6.0
90" elbow 2.0 2.5 3.0 4.0 5.0 7.0 8.0 10.0
Tee. run 0.6 0.8 0.9 1.2 1.5 2.0 2.5 3.0
Tee. branch 3.0 4.0 5.0 6.0 7.0 10.0 12.0 15.0
Gate valve 0.4 0.5 0.6 0.8 1.0 1.3 1.6 2.0
Balancing valve 0.8 1.1 1.5 1.9 2.2 3.0 3.7 4.5
Plug-type cock 0.8 1.1 1.5 1.9 2.2 3.0 3.7 4.5
Check valve. swing 5.6 8.4 11.2 14.0 16.8 22.4 28.0 33.6
Globe valve 15.0 20.0 25.0 35.0 45.0 55.0 65.0 80.0
Angle valve 8.0 12.0 15.0 18.0 no 28.0 34.0 40.0
TABLE B.9.7B
ALLOWANCE IN EQUIVALENT LENGTH OF TUBE FOR
FRICTION LOSS IN VALVES AND FITTINGS I-Copper Tubing
Equivalent feet of pipe for various sizes
Fitting or Value 112" 3/4" I" 1 114" I 1/2" 2" 21/2" 3"
45" elbow (wrought) 0.5 0.5 1.0 1.0 2.0 2.0 3.0 4.0
90" elbow (wrought) 0.5 1.0 1.0 2.0 2.0 2.0 2.0 3.0
Tee. run (wrought) 0.5 0.5 0.5 0.5 1.0 1.0 2.0
Tee. branch (wrought) 1.0 2.0 3.0 4.0 5.0 7.0 9.0
45" elbow (cast) 0.5 1.0 2.0 2.0 3.0 5.0 8.0 11.0
90" elbow (cast) 1.0 2.0 4.0 5.0 8.0 11.0 14.0 18.0
Tee. run (cast) 0.5 0.5 0.5 1.0 1.0 2.0 2.0 2.0
Tee. branch (cast) 2.0 3.0 5.0 7.0 9.0 12.0 16.0 20.0
Compression Stop 13.0 21.0 30.0
Globe Valve 53.0 66.0 90.0
Gate Valve 1.0 1.0 2.0 2.0 2.0 2.0
I From "Copper Tube Handbook" 1965, by Copper Development Association, Inc.
390 2003 National Standard Pumbing Code-!!!ustrated

B.9.8 Determination of Flow Rates Corresponding to Uniform Pipe Friction Loss
Flow rates corresponding to any given uniform pipe friction loss may be determined readily for each nominal
size ofthe kind of pipe selected for the system. Pipe friction charts I are presented herewith for each of the
standard piping materials used for water supply systems in buildings. The appropriate chart to apply in any
given case depends upon the kind of piping to be used and the effect the water to be conveyed will produce
within the piping after extended service.
These charts are based on piping in average service. If piping is used in adverse service or in retrofit applica-
tions, conservative practice suggests selecting lower flow rates for a given pipe, or larger pipe for a given
required flow rate.
For new work, with the range of materials now available, select a piping material that will not be affected by
the water characteristics at the site.

GALVANIZED STEEL
ASTM A53
~
"
,'0
- ,,,'0
\ ../" \ \ ../" '--' ../"- ../"-
1000 V
800
I \! ./ /\ '1 X ...v 1./ VI /
/ II V /1 I /
600
I
I 1\/ f\ Y I /
500
I A ->v y : \ ./
V i i V /"
Y I
I \ / 1\ V '\: v I
I ./
l,./1I /
400 I I
!\ / \
l./
300
/ I
I ! / \ / hi v1--
A I 1/
/
V
I -- - / -- -- /1 - 1\
1
4 -- /.
/
-
250 ---1--
V I / --X
-j--
I \ V 1\
---j--
Y 1 ./
[7
200
kk
v V I \ I / k::
/1 /
l./
150 I
I V
-- ---,-- I
\ 1\ X -,-
I / V
100
: /
/
1\ Y ./
/ K 1 /
/
V
/
:2: '--
- I \ / 1/ v: 1-/ V \: y ./
/
80 v
0-
U 60 I
1\:
/
V
/
\v
V"'\I
/1
I
IV
\ / \
r\ ./
\,1/
\ /1
I
1./
V
./v
l./
50 V \
40
I
/ / 1\v VI \ V / I /
W V
f- Y I
I 1\ /
V
v-: \ I
I /
/ 1\ v 1\
I
I
' V l./
30
25
/
--+--I I V\
- --1----1--
1
-- - - -- - L --
0::::
1/ , '\V 1/ )( ./
"7
\ ./
./
5
20 I
V - \ - T v: - - -J\
I /
-- --
0
15 ---j---
V( -j--
II \; -.7
\ /'
/
----1
LL Y I
1 ../
V [/f I /
V
\Y \: /
/
10
8
/
: : v /'
./
: v
/
\
/
V \1 \ / K
6 :/ Vi
V
/
V
\ V /1
:
I
k T.Y\ 7 \ \
5 A !./ IY' / I \
I... V! ./ V \1 Y \ / I \ I
\
4
3 A I
I
'
/
V
Y I
I
v
...V r\
,-
I
I N '\ 1\
___L_- v - - - I - -- 1-- I -J\II -- -- --
2.5
I
I l/rI / -+\
I -r: 7"
\--:--
2 / I
\
I / I
1.5 4- --1- - -- -- - - -- 1-- -...J.-
I
. -- - -
1
I
I
'/ /
v I
I I -\ I
I 1\ 1\
.1 .15 .2 .25.3 .4.5.6 .8 1 1.5 2 25 3 4 5 6 8 10 15 20 2530 405060 80100
PRESSURE DROP (psi/100')
FLOW VS. PRESSURE DROP

TYPE K
COPPER TUBE
~
1000
t\\yS
\
fQ\YS
'
CO\yS
\
\\:.JWS \'t\YS
\ \~ flfl 3"
~
800 : \ 1 \ \ 1 /!\ // / 1
600 : "( 1\ \: l-\:v // : :
500 1 I \ \ / ~ /'K 1\ L I j./

1 \ VI\ j)(: ).; /v ~ 2"
400 : / : :
300 : : ~v J/: \ t-K \ ~ yV 1%

250
200
--+;~--\ - V~---\vK' -/+v7'/'i_--~
~
/'
\ V '/ \/ ~ /
~
1./ I 1 1
150
100
--b~--
: /
;/~
\ - - ---1 -~~-v~~\---r-:-
1 ~ !\ //! : /
--~/~-~
/
2 80 1.\\ ~ vV' Xf 1\ V\ \: y /./ ,
lJ0
:
CL r- y 1 / \ v \! V r\ \ 1/ I 1 /V 1
C) 60 /1 \! ./ /1 ~ / 1\ I\ At 1 V -.L-
50 P 1 1.// v1\ I y-\ ./ 1 ~ /
W 40 l\ : V / \ 1/ 1 \ IY \.Y\ 1 // I
f-
<t: 30 W ~ // /\J :)/ \/~: \y/ %"
CL
5:
25
20 ~\~~~\- ~/L 1\~ --~/~-\ -*~ -- -~V/
0
15
p: \ ~ ~ 1./ \ V~-i--~ ~v "
-y~ ul\; ~\
: :
LL 10 ;/' -;prt-~,>\CT \--t-t}@

8 r'! I\V \ / : ~I\ I\/V:\: \ \v 1
6 : ~I\ //r\ Y: \ .// \ : \ 1 )( 1\ %"
5 ~ 1 A \ / 1 1,,/ \ I X \ /
4 ~: / \ V \ 1 yV \ \y \ ./'\
3 / :./J\ \ y/ : \ // "i : \ //\ \

2.5
2 ---r~~ -- - ~\~v~t-- -t--- p/ \- - --~kf- -\--_\ \- ~\J
1.5 I /1 I V \ ---l~ 1 \ / I I \
rc--r~J-7~ -C-\~~1-~~~V~ \ u1--it --~~--l\
1 .15 .2 .25.3 4.5.6 .8 1 1.5 2 2.53 4 5 6 8 10 15 20 2530 405060 80100
FLOW VS> PRESSURE DROP

TYPEL
COPPER TUBE
.S
\ \ '\ \/ - /' / /
1000 V
800
I
I \1 \ \ I \ Vt' /' Y I I
I 1
600
I
'1 \ X \: X /'"
VI
1 I /'"
/'"
V
/',/
I 1\ \ /'" 1\ A / I Y
500 I 1 \ I V
400
I I 1\ /\ I X V I / ,/
I
I
I
/ /'" I
I Y
I
\ \ V: / V
/'
*
I /
300 I /' I
250 ___L--
V
4 1
-- ,L --
Y 1-V
--
'S;/' >(v
f--
/ --j"-
I ;/
- -- -
*
/
200
kr
v
\L /'"
- 1\
/> vi'
1 L
/
)?
--
150 I /' I /'" 1\ -1-
1 V
/'
100
I
I
I V
/
\ I
I
\
\
/\
V
\:
1 I
V /
/"',/
2 80 - \ Vi I V I /
1
/'
/
D-
(') 60
vt\ I
I /' \ A \ V
/"
1\
\
\ X 1 V
/'
/"'V
"SI /'" /'" \ 1 /\ /' 1\

50
\ :' Y ../
/'
\V 1 \ \ I
V
/
/
40
W
f- V 1\V
V
/'
I
I )V \/ : V /"'v
30 /
L /. V
\
<t
CL 25 /
20
-\X
'S;s 4-
I
\ /'"
V
--\ I
/'
/ X -t V
/
V: \ /\ /: \ /
t
V
5:
0
II
15
10
8
_--L--
/ I 1\ V
\ VV 7
\
./
--
/
/
I v1
V
,\
v
.7
\/' ('
)f r{1\ 1\ 1\ X
/'
V
l----=-/
vf I \ \
6
I
1/ \ V
./
1\ A :1 \ / /' 1
I j./ \( ,\
V
//
/1 1
/\ \ / I / \ I/, ,\1 \ ./
5
4
V I
I 1\ ./
V \ I v:I \ y \ ,/ )(
\
\
\ /'" \
3
A I
I V I \ / '\
/' \
2.5
2
--v
I
41
I ,/
\
V
'\ -\t--
/
-r-
1
I V \-
--
/'
A 1
-1-
I
1 -\ 1\
-\
I /"
\ / 1 \
\
VI I
1.5 ---1--
I -.1--
1 /
/- f-__-I--
I i
V
I
I \ I
1/
V 1\
I
I \ \
1
.1 .15 .2 .25.3 .4.5.6 .8 1 1.5 2 2.53 4 5 6 8 10 15 20 2530 40 5060 80100

394 2IJIJ] National Standard Pumbing Code-Illustrated

TYPE M
COPPER TUBE
3"
t>.\~S
\
r~WS
\J \
~\~s
v \ \
\J\~S 't\~S
\ \ \~
~ ~~ ~~
1000
800 : \ 1 \ \ 1 \,/1 \./ Y I .// I~
600
: 1 1\ X \: /X //: : // vKV
1 1\ \/}, A / i A "
L0
./
500 V !/(" 1 \ v 1 / 1 /
400
1 11 \ ./ \ /i \ 1 /"\ .Y 1 /
1 1 \.V \/ 1 !./K / I'y ./V
300
1 1./"\ 1\ /,'1\ \ / I ~ /
250
200
---b~ -~~~r- --y ~--- ~7\ -~ -1-7~ - ~
2
150
100
80
~ -L- ~--
:
1
't't~'j /i'
i / V
1
-~~~--
1\
1\
V
~ -I
1
I
i ./)(:
-~~--
1
i./
[/\/
\ ./~
~~\
\ /\
\/1
\
v1-
i
i 1
i / v
I
//
7C~
L vXV
W
1"
C') 60 f- /f\:
: /
/./v
/\
\~
~
, V/ \ \
/
X 1\//1
L,/
1
I
'--/ 50 1 I
\ l.xr v"""'" \ Y I 1\ /)( \/t\ 1 /1 %"
W 40
f-
<C 30 ~ 1\// //\J : ~/ )/ \: v( .dj
25
0::::
- ~~-\- V~~--- --j\4 :;~~ -- -')A -'t /;/~-- - I
S
20
P \ : 1 /\ / 1
)/ \ r H~
o
LL
15
10
8
1---P+--j);VL7
~ I
\l: '),/ /
\V
/ 1
: /v:
~ ~-Vr
1\
\--
//\
./
)f
- - ~-\1-\
:\
'\
: \ v'\
v
/~ 1
:U"
8
6 ://i \---V 1\ /: : '\ / \ i \ r \ '\ /./

5 /1 .y \ ~ 1 Y \ Y \' \/
4 : //1 I\ / \ 1//1 \ /\ I '1 /\ \

1.v1
V: 1
1/
/ \ \ /1 I
1
1
\.x / \ '\I /' r\
1
\ \
3
2.5
2 -Y~i- -- ~~r -- -\t-- -j;V ~ - \- ;:4\ -i- -\---\ \- ~~

1.5
1
~--~---~~
.1
y 1
.15.2
Vi
:
.25.3 .4.5.6
- -~~ -- -
/"\:
\/
.8 1
~ 1
1.5 2 2.53
- ~L__-
/'
1 V
~-:: ~~\- -_J_-
4 5 6 8 10
\
\:
1
\
15 20 2530 405060
:
1
- --~
-\
~- -~
1\
80100
-

CPVC / PVC / ABS
SCHEDULE 40 PIPE
\
~ /-
1000
\ /" \ \ X'-' /- /
V
800
: I\! ./ \! /1 / / 1 /
600
:
"Iv
/"
\ V\f V ./
I
I
1
I V ./
500
I v:\ ..\ v / /
./
I /
1\ 1
400
/ 1
1 \ / 1\ A\
1
1 ./ --\ Y 1 / /lC
1 V
I
I 1
, / 1
, y(' \ 1\ /
/1
I
Y ./
/"
300 / -
*
VI I /
v
250
200 / --y
--1-
I /
--
\-\ / / -"1-
Y
V -
./
150
1
V(
--1-
/ -- --
'/1
-,-
I -:/
/
\
100
1
I
1./
V
/
\ CJ\ / 1
Xf
1
I
> ./
\, v
'v v
\ \v
I
y
I /
/
/
/"
/"
2
D-
80
/1\ I
't1'<'::>./v:
1
1 /
/
/
\ /
I
1v /"
1\ I\ :
: /
./ If
C) 60 \
'--.../ 1 V ./r\ I /1 / X I /./
50 /" V
W 40
I
KI ./ 1 \ ./
V
\ )(' 1\ 1 ./ f
f- A 1\/"
/
./ v\J /\
L---- /
./\ \: yY /
./
<r: 30 ./ ./I ./.-
CL 25 ------
V ! i'\:- 7
L -- _ -1--
/
- --
P\A -\ /
-- -- -
S
20
/: \ ./ /
V
./lJ
\
-- D
7 \ ;sf:\ \{- \
--1- 1--
T
:\
15
o 1
I
/'"
I
./ ./
----.J
I /" ./
./ 1 /" / ./
V
LL 10
8
1 y )( 1/ /1 /1\ \
Y :
v \ A :
I
./ \ j/\ :
I \ \
6 I
/
I ,/"1 \ / Y )('! \1 \
5 V
4 /
AI 1 /'" \ 1/ I \ /"v \! '\ 1\ \
3
I 1
1 V \: I
1
/
./ \ \t 1\
I
\ \
I -- - /- -- - - 1-- I -- \ --
2.5
-,- -\
2
--y
1
1
1
./
/'"
-\t- I
I
\- ---!\1 I -\ \
V I \
\
\
/
4\
I
I
1
-1-- -- - - -- -
1.5 ---1--
- - -
7' 1
---1--
1 I
1
Y I
I /'"
/" 1
I
1\
1\
I
I \ \
.1 .15 .2 .25.3 .4.5.6 .8 1 1.5 2 2.53 4 5 6 8 10 15 20 2530 405060 80100
PRESSURE DROP (psi/1 00')
396 2003 National Standard Pumbing Code-f//ustrated

CPVC PVC / ABS /
SCHEDULE 80 PIPE
W" \?CC ,?" ~\~ ~ rs::> (,f:\

~ \ D ~s \1>~ ~ ~ ~ 3"
1000 : 1\ 1 \/ \ 1 \ / ,):::7 1/v 1 /7

800 : \( // \ \}/ \: ~/ ~: /v 12Y2"
600 1 J/\ \ V}.. X V 1 I/V V
500 1/: \ /r\ L)(': \ ,\v : v/: /' v I f?\
400 /: ! '\/ ;V! :/::s( f\ A : v/' /~
3~~
200 ---t~~ -- \v::? -- yq--- r\ ~~~ --bkf -;7L -- -I W
~
2
150
100
80
~ --~--~
1
~'iYs y
I V
i --
v/
1\
-1~0
\
vV'
--
"V:
---1
~ I
1
-/\--
\ ://1\
1 \~
:- 1\\[7f\
\vvj\
-=:A
VI
\:
\ / I
7
~
-i-
y
I
---
v/
v
/'/'
"-
V~
V
~
0.-
~ j)(: v/ '\ :/~ /\ 1\ ~ :V
C)
~
60
50 / II/' 1\/1 I~/' /' 1 A -~
W 40
: \ vl/ / \ 1 //1 \ Y \ A 1 /
~ 30
VV't\ /'v : \/1/' \/---\: \: /PI
IA %"
0::::
25 / I --~~ - /0?:~--1\~ --~~~-~\ ---b~ -- -t-~
5 20 I Y D ~ I/'I\ KJ--~ V
0 1 1
-1
LL 1~ ;~~--\~/77T--
VI: / \ /'/ 1 : ~
-)~stT~J?\--t~tj@
17:\ \lvt 1\ 1 \
8 I : lv-( I/v\ ! vV: \ /r\ : \ 1 K ~
6 X 1/ \ ~ !..v \ 1 X \
5V:..vr y 1 !V'\ ~ \\
4
3 /~
~ I
1
vV \ 1
1/
[../I
I
\ v
,,/ \i
'\
1\
1
\ '\
2.5 ---r---j/~ - -e-- /~-- -t--- 7L\__-e !\ -i- -\--~~I\-H

2 I Y 1 V ---l~ 1 v \ 1 1 '\
"V:--t/b?V~---Akf--
1 - - --'\--1--\ --~~--~
.1 .15.2 .25.3 .4.5 .68 1 1.5 2 2.53 4 5 6 8 10 15 20 2530 405060 80100
FLOW VSo PRESSURE DROP

CPVC TUBING
(Copper Tube Size - SDR 1 1 )
rxWS fQWS 'O\,<S
\ \\j\':S \'t\,<S\
\ \
1000 ' \
800
I
' \1 \ \ 1 1 1\ 1 I
\
600
1
1 1\ 1\ \: \: \ 1
1
1
1
! \ \ '" i\ \ ' I
500 1
400
!
1
1
1
1\ \
\
:\ \
I
1
1
1
\ I
1
1
1
1
300
1
1 1 \ I
! \ \ 1 1
I 1 1
250 --_!..._-
1
1
--1-
I
--
f\ - - -
-\1-- .\-
--
'\
-
\-
1-- 1---,--
1
-,-
1
-- -- -
V
".L
200
: 1 \ 1\ 1 I v
1 -- - - - 1 - \ --
f\1\ 1-___1_- 1
-1- /-
-- -
150
\iu
--1-
1
: \ ---\
-1-
1
! \ \
1
I
:/ i v /'"
:2
100
80 15'<S : : \! \ \ v! ! v /'
CL
G 60
,\
1
1 \ I
I '\ \ /
A
R \: Y
1 7"
V
/'
/
1 1 1\ 1 1 \ ./ / 1
'--./
50 / /
1 \1 \1 I Y \ \ 1/ /'"
40
W / \ ) v v /'
f-
1
1 1\ \J./ 1 \l/ /1
I
30 1 1 / Z /"
0::: 25
20
------
1
I
--1-
1 1\-
1 \
- -
/
- --
/'" A I
-.1--
1
/
--
/ X1\ --
/
--
/
;/
5 1
v V -- -
VX
1 / --
---L--
0
--.J
LL
15
10
8
1
1
1
1/
--1-
Y V
I
:
\
\/
/ 1
1
1
-;7
/
/
V
1\ /1\
* :\ \ /
,/
I /
/: : /
/'"
\ / ! \ /
l)\ 1
i
\ ! ,\ ::S
/
6
I Y ./ /\ Y 1 v '\ I '\ 1./ /\ \
5
i/ ! /'
/'"
\. v! 1 / '\ \1./ /\ \ \
4
3
v: IY I
./
v \
r\
1
1 /
1 --
1\
/
X
1
1\
1
\
_\ --
\
v- w- --
I /'" -
2.5 -f-- - -
--c,
;;;/
./
-1-
1 V ---!\ -1-
I -\ \ 1\
2 VI 1 -- V I
1V V \ 1
1 \
1.5
!
--1-
y
1
1 /
V
1-- - ---
vr 1
1
-
\ ----l--
1
1
1 K
-- -
1\ 1\
1
.1 .15 .2 .25.3 .4.5.6 .8 1 1.5 2 2.53 4 5 6 8 10 15 20 2530 40 5060 80100
FLOW VS, PRESSURE DROP

B.lO DETAILED SIZING METHOD FOR SYSTEMS IN
BUILDINGS OF ANY HEIGHT
For sizing water supply systems in buildings of any height, a detailed method may be applied in the design of
modern buildings. The procedure consists of sixteen steps, as follows:
1. Obtain all information necessary for sizing the system. Such information shall be obtained from responsible
parties and appropriate local authorities recognized as sources of the necessary information. (See Section B.2.)
2. Provide a schematic elevation of the complete water supply system. Show all piping connections in proper
sequence and all fixture supplies. Identify all fixtures and risers by means of appropriate letters, numbers, or
combinations thereof. Identify all piping conveying water at a temperature above 150F, and all branch piping to
such water outlets as solenoid valves, pneumatic valves, or quick-closing valves or faucets. Provide on the sche-
matic elevation all the general information obtained per step I. (See Section B.2.9.)
3. Mark on the schematic elevation, for each section of the complete system, the hot and cold water loads
served in terms of water supply fixture units in accordance with Table B.5.2.
4. Mark on the schematic elevation, adjacent to all fixture unit notations, the probable maximum demand in
gallons per minute corresponding to the various fixture unit loads in accordance with Table B.5.4.
5. Mark on the schematic elevation, for appropriate sections of the system, the demand in gallons per minute
for outlets at which demand is considered continuous, such as outlets for watering gardens, irrigating lawns, air-
conditioning apparatus, refrigeration machines, and similar equipment. Add the continuous demand to the demand
for intermittently used fixtures, and show the total demand at those sections where both types of demand occur.
(See Section B.5.4.)
6. Size all individual fixture supply pipes to water outlets in accordance with the minimum sizes permitted by
regulations. Minimum fixture supply pipe sizes for typical plumbing are given in Table B.5.2.
7. Size all other parts of the water supply system in accordance with velocity limitations recognized as good
engineering practice, and with velocity limitations recommended by pipe manufacturers for avoiding accelerated
deterioration and failure of their products under various conditions of service. Sizing tables based on such velocity
limitations and showing permissible loads in terms of water supply fixture units for each size and kind of piping
material have been provided and may be applied as a convenient and simplified method of sizing in this step. (See
Section B.6)
Note: These sizes are tentative until verified in Steps 12,13,14, 15.
8. Assuming conditions of no-flow in the system, calculate the amount of pressure available at the topmost
fixture in excess of the minimum pressure required at such fixtures for satisfactory supply conditions. This excess
pressure is the limit for friction losses for peak demand in the system (1' of water column = 0.433 psi pressure).
(See Section B.9.2.)
9. Determine which piping circuit of the system is the basic one for which pipe sizes in main lines and riser
should be designed in accordance with friction loss limits. This circuit is the most extreme run of piping through
which water flows from the public main, or other source of supply, to the highest and most distant water outlet.
This basic design circuit (BDC) should be specifically identified on the schematic elevation of the system. (See
Section B.9.3.)
10. Mark on the schematic elevation the pressure loss due to friction corresponding to the maximum probable
demand through any water meter, water softener, or instantaneous or tankless water heating coil that may be
provided in the BDC. (See Sections B.9.4 and B.9.5.)
11. Calculate the amount of pressure remaining and available for dissipation as friction loss during peak demand
through pipe, valves, and fittings in the BDC. Deduct from the excess static pressure available at the topmost
fixtures (determined in step 8), the friction losses for any water meters, softeners, and water heating coils provided
in the BDC determined in step 10. (See Section B.9.4.)

12. Calculate the total equivalent length of the BDC. Pipe sizes established on the basis of velocity limitation in
step 7 for main lines and risers must be considered just tentative at this stage, but may be deemed appropriate for
determining corresponding equivalent lengths of fittings and valves in this step. (See Section B.9.7.)
13. Calculate the permissible uniform pressure loss for friction in piping of the BDC. The amount of pressure
available in the circuit for dissipation as friction loss due to pipe, fittings, and valves (determined in step 11), is
divided by the total equivalent length of the circuit (determined in step 12). This establishes the pipe friction limit
for the circuit in terms of pressure loss in psi per foot of total equivalent pipe length. Multiply this value by 100 in
order to express the pipe friction limit in terms of psi per 100 feet oflength. (See Section B.9.6.)
14. Set up a sizing table showing the rates of flow for various sizes of the kind of piping to be used, correspond-
ing to the permissible uniform pressure loss for pipe friction calculated for the BDC (determined in step 13). Such
rates may be determined from a pipe friction chart appropriate for the piping to be used and for the effects upon
the piping ofthe quality of the water to be conveyed thereby for extended service. (See Sections B.9.8 and B.2.3.)
15. Check the sizes of all parts of the BDC, and all other main lines and risers which supply water upward to
the highest water outlets on the system, in accordance with the sizing table set up in step 14. Where sizes deter-
mined in this step are larger than those previously established in step 7 (based on velocity limitation), the increased
size is applicable for limitation of friction.
16. Due consideration must be given to the action of the water on the interior of the piping, and proper allow-
ance must be made where necessary as a design consideration, such as, where the kind of piping selected and the
characteristics of the water conveyed are such that an appreciable buildup of corrosion products or hard-water
scale may be anticipated to cause a significant reduction in bore of the piping system and inadequate capacity for
satisfactory supply conditions during the normal service life of the system. A reasonable allowance in such cases is
to select at least one standard pipe size larger than the sizes determined in the preceding steps. Where the water
supply is treated in such manner as to avoid buildup of corrosion products or hard-water scale, no allowance peed
be made in sizing piping conveying such treated water. (See Sections B.2.3 and B.9.8.)
B.ll ILLUSTRATION OF DETAILED SIZING METHOD APPLICATION
B.11.1 Example
A seven-story building is supplied by direct street pressure from a public water main in which the minimum
available pressure is 60 psi. The highest fixture supplied is 64'-8" above the public main, and requires 12 psi
flow pressure at the fixture for satisfactory supply conditions.
The water supply is to be metered by a meter through which flow at the maximum probable demand rate will
produce a pressure drop of 5.6 psi. Copper tubing, Type L, is to be used for the entire system. Quality ofthe
water supply is known to be noncorrosive to copper tubing in the water district, and is recognized as being
non-scaling in characteristic.
The entire system has been initially sized in accordance with the simplified method based solely on velocity
limitations. Applying these sizes, the total equivalent length of piping from the public main to the highest and
most remote fixture outlet has been calculated to be 600'.

B.ll.2 Solution
Steps 1-7. The first seven steps of the details sizing method have already been performed. These steps
constitute the simplified sizing method based solely on velocity limitations established as the design basis. All
that remains is to perform steps 8 through 15 of the detailed sizing method which relate to sizing in accor-
dance with the frictional limitation which must be observed for this particular system, and with allowances
which may be necessary in view of the water characteristics.
Step 8. Assuming conditions of no-flow in the system, the amount of excess pressure available at the
topmost fixture in excess of the minimum required at the fixture for satisfactory supply conditions is deter-
mined as follows:
Excess pressure available = 60 psi - 12 psi - (64.67 x 0.4333 psi/ft) = 20 psi
Step 9. The BDC should be specifically identified on the schematic elevation provided as per step 2.
Step 10. The pressure loss through the water meter selected for this system for flow at maximum probable
demand is given in the example as being 5.6 psi. No other items of equipment through which significant
friction losses may occur have been noted in the example.
Step 11. The amount of pressure remaining for dissipation as friction loss during peak demand through
pipes, valves, and fittings in the basic design circuit is determined as follows:
Pressure available for friction in piping = 20 psi - 5.6 psi = 14.4 psi
Step 12. The total equivalent length of the basic design circuit has been given in the example as being 600
feet, based on the sizes determined in accordance with velocity limitations as per step 7.
Step 13. The permissible uniform pressure loss for friction in piping of the basic design circuit is deter-
mined as follows:
Permissible uniform pipe friction loss = 14.4 psi x (100 ft/600 ft)
= 2.4 psi per 100 ft pipe length
Step 14. A sizing table showing the rates of flow through various sizes of copper tubing corresponding to a
pipe friction loss rate of 2.4 psi per 100 feet of pipe length is given in Table B.11.2. These flow rates were
determined from the chart applicable to such pipe with a "fairly smooth" surface condition after extended
service conveying water having the effect stated in the example.
Step 15. All parts of the BDC should be selected in accordance with the flow rates shown in the table
established in step 14. Usually, all other parts of the system are sized using the same pressure drop limitation.
------------------------------------------------------------------------------------
TABLEB.ll.2
TYPE LCOPPER TUBING, FOR "FAIRLY SMOOTH" CONDITION
Nominal Pipe Flow Rates Corresponding to Friction
Size Loss of 2.4 psi/IOO'
(in) (gpm)
1/2 1.4
3/4 3.9
1 7.5
1-1/4 14.0
1-1/2 21.0
2 47.0
2-1/2 78.0
~
.) 130.0
4 270.0

B.12 MANIFOLD TYPE PARALLEL WATER DISTRIBUTION SYSTEMS
B. 12.1 Manifolds
The total water supply demand for the dwelling shall be determined in accordance with Section 10.14 and
Appendix B.S. Manifolds shall be sized according to Table B.12.1 based on the total supply demand.
TABLE B.12.1
MANIFOLD SIZING'
Nominal Size ID Maximum GPM Available@ Velocity
Inches @ 4 fps @8 fps @ 10fps
1/2 2 5 6
3/4 6 II 14
1 10 20 25
1-1/4 15 31 38
1-1/2 22 44 55
I Refer to Section 10.14 for maximum velocity permitted.
B.12.2Distribution Lines
a. The water pressure available for distribution pipe friction shall be determined from the minimum supply
pressure available at the source, the developed length and size of the water service, the pressure drop through
the water meter (if provided), the pressure drop through the manifold, the pressure drop through any other
equipment or appurtenances in the system, the elevation of each distribution line, and the minimum pressure
required at each fixture.
b. The water flow required at each fixture shall be in accordance with Section 10.14.2a for both hot and
cold water. Distribution line sizes shall be in accordance with the system manufacturer's line sizing proce-
dure.
c. The system manufacturer shall provide sizing data for the individual runs of tubing to each fixture based
on the water pressure available for pipe friction and static elevation, the GPM required at each fixture, the
tubing material, the tube size, and its maximum allowable length from the manifold to the fixture. Tube sizes
for parallel water distribution systems include 3/8" nominal, 1/2" nominal, and 3/4" nominal.
B.13 PLASTIC PIPING SYSTEMS SUITABLE FOR HOT AND COLD

WATER DISTRIBUTION}
B.13.1 ASTM D2846 Chlorinated Poly (Vinyl Chloride)(CPVC)Plastic Hot and Cold Water Distribu-
tion Systems (3/8" thru 2") (CPVC 41) (SDR 11). Rated and marked 100 psi at 1800F.: all sizes.
B.13.2 ASTM F441 Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80 (11
4" thru 12"). Rated and marked 400 psi at 730F. derated to 100psi at 1800F.: Schedule 40, not threaded: 1/4"
thru 1"pipe size Schedule 80, not threaded: 1/4"thru 2" pipe size Schedule 80, threaded: 1/4"thru 1/2"pipe size.
B.13.3 ASTM F442 Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR), (114" thru
12"). Rated and marked 400 psi at 730F. derated to 100 psi at 1800F: SDR 11 only, all sizes, not threaded.
B.13.4 ASTM F877 Crosslinked Polyethylene (PEX) Plastic Hot and Cold Water Distribution Sys-
tems with ASTM D1807 metal insert fittings (3/8" thru 2") (SDR 9), ASTM Fl960 Cold Expansion
Fittings or ASTM F2098 Stainless Steel Clamps. Rated and marked 100 psi at 1800F.: all sizes.
NOTES: (1) Refer also to manufacturer's recommendations, instructions, and limitations.

Appendix C
Conversions:
Customary Units to Metric
Square Measure Conversions from

Square Inches to
ApproximateSquareCentimetersand
Square Feet to Approximate Square Meters
Square Square Square Square
Inches Centimeters Feet Meters
1 6.5 1 .0925
2 13.0 2 .1850
3 19.5 3 .2775
4 26.0 4 .3700
5 32.5 5 .4650
6 39.0 6 .5550
7 45.5 7 .6475
8 52.0 8 .7400
9 58.5 9 .8325 Temperature Conversions from
10 65.0 10 .9250 Degrees Fahrenheit to
25 162.5 25 2.315
50 325.0 50 4.65 Approximate Degrees Celsius
100 650.0 100 9.25
FahrenheiWF) Celsius CC)
32 0
40 4
50 10
60 15
70 21
80 26
90 32
100 38
120 49
140 60
160 71
180 82
200 93
212 100

Liquid Volume Time Conversions
(Flow-Rate Conversions)
From Gallons Per Minute Liquid Volume Conversions from
to Approximate Litres Per Minute Liquid Ounces and
U.S. Gallons to Litres
GPM LitreslMinute
Ounces Litres Gallons Litres
1 3.75
2 6.50 1 .0296 1/4 .9464
3 11.25
2 .0591 1/2 1.893
4 15.00
3 .0887 3/4 2.839
5 18.75 4 .1183 1 3.785
6 22.50 5 .1479 2 7.571
7 26.25 6 .1774 3 11.36
8 30.00 7 .2070 4 15.14
9 33.75 8 .2366 5 18.93
10 37.50
9 .2662 6 22.71
10 .2957 7 26.50
16 (1 pt.) .4732 8 30.28
20 .5915 9 34.07
30 .8872 10 37.85
32 (1 qt.) .9464 20 75.71
30 113.6
40 151.4
50 189.3
100 378.5
Length/Time Conversions from

Feet Per Second to
Approximate Meters Per Second
Feet Per Meters Per Mass Conversions from
Second Second Ounces and Pounds to Kilograms
1 .3050 Ounces Pounds
2 .610 Kilograms Kilograms
3 .915
4 1.220 1 .028 1 .454
5 1.525 2 .057 2 .907
6 1.830 3 .085 3 1.361
7 2.135 4 .113 4 1.814
8 2.440 5 .142 5 2.268
9 2.754 6 .170 6 2.722
10 3.05 7 .198 7 3.175
8 .227 8 3.629
9 .255 9 4.082
10 .283 10 4.536
11 .312 25 11.34
12 .340 50 22.68
13 .369 75 34.02
14 .397 100 45.36
15 .425
16(1 lb.) .454

Determining the Minimum Number of
Required Plumbing Fixtures
The determination of the minimum number of required plumbing fixtures is a complex issue as many buildings are
unique as such the Authority Having Jurisdiction is called upon to use good judgement in applying this procedure.
1. DETERMINE THE SERVICE POPULATION

The population for the building or facility should be given on the plans. In the event the population of the building
or service area is not given on the plans, three approaches may be utilized in determining the population to be
served by the restroom facility.
(a.) Actual: In some instances the actual population, male and female, ofthe building service area may be
known and this value may be used in the calculations.
(b) Engineering Estimate: The population of many buildings, especially those owner-occupied, may be
determined on the basis of population densities. Typically, office building floor areas range from 200 to 400 square
feet per person. In the absence of other data, the gender ratio should be 60/60 which allows for a variance.
(c) Legal Limit: Many building codes establish a legal occupancy limit based on the means of egress. Where
the occupant load is based on the egress requirements of a building, the number of occupants for plumbing pur-
poses shall be permitted to be reduced to two-thirds of that required for fire or life safety purposes.
2. MINIMUM NUMBER OF REQUIRED PLUMBING FIXTURES

The minimum number of required plumbing fixtures shall be determined based on building classification, user group
and population as given in Table 7.21.1. The building classifications and user groups are consistent with nationally
recognized building codes.
EXAMPLE A
Building classification, user group and total population given.
Buildingclassification: A-3 Assembly without fixed seats

Floor area: 20,000 square feet net
Population: 2,857 based on egress

1. Determine the Service Population
Since the given population is based on egress, the number of occupants for plumbing purposes shall be 2/3 of this
value.
Population for plumbing purposes = 2,857 x 2/3 = 1,905 occupants
Male population = 1,905 x 0.60 = 1,143

Female population = 1,905x 0.60 = 1,143
2. Determine the Minimum Required Plumbing Fixtures
The minimum required fixtures are determined from Table 7.21.1 under 1 Assembly, Use Group A-3 as follows:
The male and female populations are beyond the maximum range shown in the test, therefore the number of water
closets for the male population is determined as:
1 for the first 50 men

add 1 for the next 99 men (51 - 150)
add 0 for the next 149 men (151-300)
add 3 for the next 3 intervals of 300 men
Required water closets 5
The number of intervals of 300 men is determined as:
Total male population - Male population accounted for (first 300)

Population served by each additional fixture
1,143 - 300 divided by 300 = 2.81 Round off to 3
The total for the other fixture types are calculated in the same manner.
The required fixtures are:
Fixture Male Female Common
Water '" O<:PT<: ,,\1 q

Lavatories 4 8
Drinking Water Facilities 22

Service Sinks 1
lThe five water closets serving the male population may be installed as three water
closets and two urinals as permitted by Note 5 of Table 7.21.1.
2Based on combined male and female population 1,905 rounded to 2,000.
406 2003 Nathmal Standard Pumbing Code-lllustrated

EXAMPLE B
Building classification, user group and total population given.
Determine the required plumbing fixtures for the following space.
Building classification: B Business, Office Building

Dimensions: 290 x 170 feet
Area: 49,300 square feet
Population: 394 Actual Occupancy
1. Determine the Service Population
Populations for each sex taken as 60 percent of the total population
Male = 394 x 0.60 = 236

Female = 394 x 0.60 = 236
2. Determine the Minimum Required Plumbing Fixtures
From Table 7.21.1, Section 2, Business, Use Group B the fixture requirements are determined as follows:
Male Water Closets

1 for the first 15 men
add 3 for the next 3 intervals of 60 men
Total water closets 6
The number of intervals of 300 men is determined as:
Total male population - Male population accounted for (75)

Population served by each additional fixture
236 - 75 divided by 60 = 2.68 Round off to 3
The total for the other fixture types are calculated in the same manner.
The required fixtures are:
Fixture Male Female Common
Water Closets 61 9
Lavatories 5 10
Drinking Water Facilities 1
Service Sinks 1
1The six water closets serving the male population may be installed as three water closets
and three urinals as permitted by Note 5 of Table 7.21.1.

Blank page

Special Design
Plumbing Systems
E.I GENERAL REQUIREMENTS
E.1.1 Special design plumbing systems shall include all systems which vary in detail from the requirements
of this Code.
E.1.2 The provisions of this Appendix shall control the design, installation, and inspection of special design
plumbing systems.
E.1.3 Special design plumbing systems shall conform to the Basic Principles of this Code.
E.2 PLANS, SPECIFICATIONS, AND COMPUTATIONS
E.2.1 Plans, specifications, computations and other related data for special design plumbing systems shall be
submitted to the Authority Having Jurisdiction for review and approval prior to installation.
E.2.2 RESERVED
E.3 INSTALLATION OF SPECIAL DESIGN PLUMBING SYSTEMS

Special design plumbing systems shall be installed according to established, tested and approved criteria.
EA CERTIFICATION OF COMPLIANCE
E.4.1 The complete installation and performance of the special design plumbing system shall be tested and
certified by an approved independent agency, as complying with Sections E.l.3 and E.3 above.
E.4.2 Inspections shall be made by the Authority Having Jurisdiction to ensure conformance with data
submitted for approval.

E.5 VACUUM DRAINAGE SYSTEMS
E.S.l General Requirement
E.S.1.1 System Design

Vacuum drainage systems shall be designed in accordance with manufacturer's recommendations.
The system layout, including piping layout, tank assemblies, vacuum pump assembly and other compo-
nents/designs necessary for proper function of the system shall be per manufacturer's recommenda-
tions. Plans, specifications and other data for such systems shall be submitted to the Authority Having
Jurisdiction for review and approval prior to installation.
E.S.1.2 Fixtures
Gravity type fixtures used in vacuum drainage systems shall comply with Chapter 7 of this Code.
ES.l.3 Drainage Fixture Units

Fixture units for gravity drainage systems which discharge into or receive discharge from vacuum
drainage systems shall be based upon values in Chapter 11 ofthis Code.
ES.l.4 Water Supply Fixture Units

Water supply fixture units shall be based upon values in Chapter 10 of this Code with the addition that
the fixture unit of a vacuum type water closet shall be one inch.
E.S.1.S Traps and Clean outs

Gravity type fixtures shall be provided with traps and cleanouts per Chapter 5 of this Code.
E.S.1.6 Materials
Vacuum drainage pipe, fittings and valve materials shall be as recommended by the vacuum drainage
system manufacturer and as permitted by this Code.
E.S.2 Tests and Demonstrations
After completion of the entire system installation, the system shall be subjected to a vacuum test of 19 inches
of mercury and shall be operated to function as required by the Authority Having Jurisdiction and the manu-
facturer. Recorded proof of all tests shall be submitted to the Authority Having Jurisdiction.
E.S.3 Written Instructions
Written instructions for the operation, maintenance, safety and emergency procedures shall be provided to the
Building Owner as verified by the Authority Having Jurisdiction.

Requirements of the
Authority Having Jurisdiction
F.l GENERAL
This Code does not include specific requirements in certain cases where local practices may vary from one
jurisdiction to another. This appendix lists those sections of this Code where the Authority Having Jurisdiction must
establish requirements. Adopting agencies should review the sections listed under Appendix F.2 and establish
appropriate regulations or policies.
F.2 REFERENCES
1.7.2 Penalties
1.9.8 Permit Expiration
1.10.2 Plan Review Fees
1.10.3 Plan Review Expiration
1.10.5 Refunding of Fees
1.11.5 Requests for Inspection
2.16.a: Minimum earth cover for water service pipe.
2.16.b: Minimum earth cover for building sewers.
2.19.1: Distance for required connections to public water supplies and sewers.
2.19.2: Standards and requirements for private water and sewage disposal systems.
5.3.4: Need for building traps.
5.4.10.c: Manhole construction standards.
6.1: Need for interceptors.
6.1.8: Point of discharge for effluent from interceptors.
6.2.1 : Discharge of commercial dishwashers and food-waste-grinders through grease interceptors.
6.2.7: Location of grease interceptors.
6.3.2.e: Environmental requirements for waste oil tanks.
6.3.4: Approval of combination oil and sand interceptors.
7.2: Requirements for accessible fixtures.
7.4.2 (2): Use of blowout water closets.
7.4.2 (3): Use of 3.5 GPF water closets.
7.5.2: Use of blowout urinals.
9.4.3.c: Points of discharge for air conditioning condensate.
2003 National Standard Pumbing Code..Illustrated 411

10.9.2: Disinfecting water piping.
11.7.6: Use of grinder pumps.
11.7.10: Use of macerating toilet systems.
12.18: Need for relief vent on building drain.
13.1.10.4: Design rainfall rates.
15.3.1: Testing new plumbing work.
15.3.2: Testing existing sewers and drains.
F.3 EXCEPTIONS, WAIVERS, APPROVALS

There are instances where this Code specifically permits exceptions or waivers of its requirements and the
approval of alternative materials and methods by the Authority Having Jurisdiction. These occur throughout this
Code.

Graywater Recycling
Systems

G.l FORWARD
In the United States today, regulations concerning water conservation, moratoriums on sewer connections, and
restrictions on sewer permits are a clear indication of a growing economy restrained by a lack of available water.
Water being a finite resource, these actions serve as a warning that without adequate planning for our future water
needs, America is facing a critical water supply shortage.
In virtually all major metropolitan and many suburban areas in the country, water treatment plants are over-
loaded and many, due to neglect and deferred maintenance, are beginning to fail. Finding additional water sources
and supplies and expanding existing water treatment plant capacity is expensive, sometimes impractical, and at
best, involves long range planning.
Traditionally, the municipal treatment facility has been the primary source of water disposal for single and multi-
family residential buildings and complexes. As long term water shortages increasingly are predicted in several
areas across the nation, water conservation becomes more of a national issue. Fortunately, alternative technical
solutions are currently available.
Various potentially useful and dependable water treatment and recycling technologies are being explored. One
possible source is graywater recycling, an on-site wastewater treatment and recycling system, also known as
"Graywater Systems". This promising technology offers a practical solution to the water shortage problem as it
applies to plumbing installations. Graywater systems are designed to safely manage wastewater and reduce water
consumption. Graywater systems can be used in all types of residential, commercial, institutional, and industrial
buildings. Some gray water applications include toilet and urinal flushing, landscape irrigation, supply water for
ornamental ponds and make-up water for cooling towers.
G.2 DEFINITIONS
G.2.1 Biological Treatment: A method of wastewater treatment in which bacterial or biochemical action is
intensified as a means of producing an oxidized wastewater.
G.2.2 Black Water: Used untreated water that is flushed down toilets and urinals. This water cannot be
directly reused.
G.2.3 Effluent: Partially or completely treated liquid waste discharge from a wastewater treatment system.
G.2.4 Graywater: Used untreated water generated by clothes washing machines, showers, bathtubs and
lavatories. It shall not include water from kitchen sinks or dishwashers.
G.2.5 Reclaimed Water: Effluent from a wastewater treatment facility that has been subjected to extensive
treatment in order to remove organic material, heavy metals, and harmful pathogens (such as bacteria,
viruses, and protozoa). Reclaimed water is non-potable.
G.2.6 Septic Tank: A water-tight receptacle which receives the discharge of a building sanitary drainage
system or part thereof, and is designed and constructed so as to separate solids from the liquid, digest organic
matter through a period of detention, and allow the liquids to discharge into the soil outside of the tank through
a system of open joint or perforated piping, or a seepage pit.
G.2.7 Wastewater: The combination ofliquid and water-carried pollutants from residences, commercial
buildings,industrialplants,andinstitutions.

G3 APPROVED MATERIALS
All materials, fixtures or equipment used in the installation, repair or alteration of graywater systems, shall conform
to the standards set forth in Chapter 3 of this Code. Nothing contained herein shall prohibit the Authority Having
Jurisdiction from imposing more stringent requirements.
Materials not listed in Chapter 3 of this Code may be used with the approval of the Authority Having Jurisdiction
as permitted in Section 3.12.2.
G4 APPROVED INSTALLATIONS
Prior to construction of a graywater system, the appropriate permits shall be obtained from the Authority Having
Jurisdiction havingjurisdiction. The applicant shall provide the Authority Having Jurisdiction with complete plans
and manufacturers' recommendations of the proposed installation.
All pipe sizing and installation procedures shall conform to the applicable sections of this Code. Nothing shall
preclude the Authority Having Jurisdiction from requiring more stringent compliance procedures.
G5 PROHIBITED INSTALLATIONS
Surface draining graywater shall not be permitted to collect on the surface of the ground or to run off the property.
Graywater shall not be permitted to come in direct contact with edible food sources.
G6 ACCEPTABLE TREATMENT METHODS
G.6.1 Nylon or Cloth Filter

The nylon or cloth filter system typically consists of a filter bag connected to the graywater inlet pipe in a
tank. The graywater is passed through the filter media (which collects hair and lint) and proceeds on for
further treatment.
G.6.2 Sand Filter

The sand filter system consists of a sand and rock filled tank with an underdrain system. The graywater is
poured onto splash plates and then filtered through filter media, while receiving physical and biological treat-
ment. The filtered graywater then is collected and transported via an underdrain system for reuse.
G.6.3 Diatomaceous Earth Filter

Diatomaceous filters are commonly used for filtering water for swimming pools and spas. The use ofthis
type of filter is primarily limited to separating solids in suspension with the use of a recirculating line.
G.6.4 Rack or Grate Filters

The primary function of the rack or grate filter is to remove particle matter from the graywater.
G.6.5 Collection and Settling

Commonly found in septic systems, whereby solids flow into the tank and are permitted to settle to the bottom
forming a sludge layer.
G.6.6 Biological Treatment Units

Typically a process in which solids are separated through the use of three chambers. Pre-settling, aeration,
and final settling separate the solids while allowing biological treatment prior to reuse. This type of treatment
is usually found in large commercial applications.
2003 National Standard Pumbing Code-1!/ustrated 415

G.6.7 Reverse Osmosis
A process involving treatment of the graywater by a reverse osmosis unit.
G.6.8 Physical/Chemical Treatment

Graywater is processed through a rapid mix tank in which polymer and activated carbon are added. The
treated graywater is then passed through a settling tank in which sludge is removed. The graywater then
goes on to numerous filters for further treatment.
G7 DISINFECTION TECHNIQUES
UltravioletIrradiation
Ozone
Chlorine
Iodine
G8 IRRIGATION METHODS
Mini- Leachfield
Drip Irrigation
G9 PROTECTION OF THE POTABLE WATER SUPPLY

A graywater system shall be designed, installed and maintained to prevent contamination from non-potable liquids,
solids or gases into the potable water supply through cross-connections.
In all buildings where dual water systems are installed, one potable water and one non-potable water, each
system shall be identified either by color marking or metal tags, or other appropriate method as approved by the
Authority Having Jurisdiction having jurisdiction. Each outlet on the non-potable water line which may be used for
drinking or domestic purposes shall be posted: DANGER-UNSAFE WATER.
The potable water supply shall be protected from backflow and back-siphonage by an approved method of
cross-connection control required by Sections 10.4 and 10.5 of this Code. Nothing contained herein shall prohibit
the Authority Having Jurisdiction from requiring more stringent requirements.
GI0 TESTING
All applicable sections of this appendix shall conform to the body of this Code. Installation of the graywater
system shall conform in all aspects to the manufacturers recommended installation procedures.
Systems shall be tested and comply with the Authority Having Jurisdiction. Piping, valves, and fittings shall be
tested in compliance with Chapter 15 of this Code.
Gll MAINTENANCE
The graywater system shall be maintained in accordance with the manufacturers recommended maintenance
instructions.
Nothing in this Appendix shall preclude the Authority Having Jurisdiction from requiring additional maintenance
procedures.

INSTALLATION OF
MEDICAL GAS
AND VACUUM PIPING
SYSTEMS
(Refer to NFPA 99-2002 and NFPA 99C-2002)
2003 National Standard Pumbing Code-JIIustrated 417

Blank Page

Xppelld~x>1
Fixture Unit Value

Curves for Water Closets

1.1 DRAINAGE FIXTURE UNITS-WATER CLOSETS
Chart I.l(a)
Drainage Fixture Units. Water Closets
Heavy Use Assembly
\0
-'" 8
-=
;J
6
~ 4
-::I
>o! 2
rz 0,
0 O~ 0.4 ~6 O~ 1 I~ 1.4 1.6 1~
Flush Volume(Gallons)
I --- Gravityq=16 -0- Valveq=192 -.- PressTankq=32
Chart 1.1(b)
-
Drainage Fixture Units Water Closets
Other than Dwellings
10
-'"
.a 8
;J 6
n
~ 4
-::I
>o! 2 ....
rz
0,
.
0 0.2 0.4 0.6 O~ 1 1.2 1.4 1.6 1.8
I --- Gravityq=16 -0- Valveq=192 -.- PressTankq=32
ChartI.l(c)
-
Drainage Fixture Units Water Closets
Dwellings
10
:l 8
-= 6
;J
4
-::I
>o!2
.71
s 01 I
.....
.
0 O 0.4 ~6 ~8 1 1~ 1.4 1.6 1~
I ---Gravityq=16 --0- Valveq=19.2 -.-PressTankq=32
@1994 Slevens Institute of Technology
420
2003 National Standard Pumbing Code~!//ustrated
1.2 WATER SUPPLY FIXTURE UNITS - WATER CLOSETS
ChartI.2(a)
-
Water Supply Fixture Units Water Closets
Heavy Use Assembly
\10
:9
8
7
=
;; 6
;:I 5
2::
=
.... 4
.~
~ 3
2
1
0,
0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8
Flush Volume (Gallons)
--- Press
Tank -0- Gravityq=2.4 -+- Valveq=20 -0- Valveq=24
q=1.5
Chart 1.2(b)
-
Water SupplyFixture Units Water Closets
Dwellings and other Services
10
9
8
7 1.;'
'"
'S 6
;:J 5
2::
~ 4
~
~ 3
2
1
0 I
0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8

Flush Volume (Gallons)
--- PressTank -0- Gravity

q=2.4-+- Valveq=20 -0- Valveq=24
q=1.5
@1994 Stevens Institute of Technology

Blank Page

Acceptable Sizing
Criteria

SIZING GREASE INTERCEPTORS
Waste waters that are not grease laden and do not require separation shall not be discharged into any grease
interceptor.
1. Determine the cubic content ofthe fixture, equipmenfor sink compartment that will produce the grease
laden waste water that will require separation. Length X Width X Depth
2. Determine the capacity in gallons. 1gallon = 231 cubic inches.
3. Determine the actual drainage load.

a. The fixture is usually filled to about 75% of capacity with water.
b. The items being washed displace about 25% of the fixture content.
c. Actual drainage load = 75% ofthe fixture, equipment or sink compartment.
4. Determine the drainage rate.

a. In general, good practices dictate a one minute drainage period.
b. However where conditions permit, a 2-minute drainage period is acceptable.
c. Drainage rate = Drainage period is the actual time required to completely drain the unit.
5. Determine the flow rate.

Flow rate = Actual drainage load (divided by) Drainage rate.
6. Select trap size based on calculated drainage rate and flow rate.

Flow In
Sloping Drains

Flow in Sloping Drains
TableK-llists dischargerates ingallonsper minuteand velocitiesin feetper secondforvarioussizedrainsat
variousslopes. Theminimumflowvelocityto achievescouringin a drainlineistwo(2) feetper second. For
this reason, drains thatare 3 inchesand smallerin sizemust be slopedatnot lessthan 1/4inchper foot.
Even at 1/4" per foot slope, the uniform flow velocity in drains that are 1-112"and 2" size is less than 2 feet per
second. The length of such drains should be keptto a minimum so thatthe entrance velocity will provide
adequate scouring for the short distance involved.
Horizontal sanitary drain and waste pipes are sized to be one-half(1I2) full under design loads. Horizontal
storm drains are sized to run full under design loads. The following drain pipe sizing tables are based on Table
K-l:
Table 11.5.1A Building Drains and Sewers

Table 11.5.1B Horizontal Fixture Branches and Stacks
Table 13.6.2 Size of Horizontal Storm Drains
TABLEK-t
APPROXIMA TE DISCHARGE RATES ANDVELOCITIES
IN SLOPING DRAINS
Flowing HalfFulP
Discharge Rate and Velocity'
1/16 in./ft. 1/8 in.!ft. 114 in.!ft. 1/2in./ft.
lli!ill lli!ill lli!ill
Actual inside
diameter of Disch. Vel. Disch, Vel. Disch, Vel. Disch, Vel.
pipe-Inches gpm fps gpm fps gpm fps gpm fps
11/. 3.40 1.78

I'lx 3.13 1.34 4.44 1.90
III, 3.91 1.42 5.53 2.01
Jsix 4.81 1.50 6.80 2.12
2 8.42 1.72 11. 9 2.43
211, II. 8 1.4 J 15.3 1.99 21.6 2.82
3 17.6 1.59 24.8 2.25 35.1 3.19
4 26.7 1.36 37.8 I. 93 53.4 2.73 75.5 3.86
5 48.3 I. 58 68.3 2.23 96.6 3.16 137. 4.47
6 78,S 1.78 Ill. 2.52 157. 3.57 222. 5.04
8 170. 2.17 240. 3.07 340. 4.34 480. 6.13
10 308. 2.52 436. 3.56 616. 5.04 872. 7.12
12 500, 2.83 707. 4.01 999. 5.67 1413. 8.02
1. Half full means tilled to a depth equal to one-half of the inside diameter.
2. Computed ti'om the Manning Formula for 1/2-full pipe, n=O.O15
For 1/4 full: multiply discharge by 0.274 For full: multiply discharge by 2.00
multiply velocity by 0.701 multiply velocity by l.OO
For 3/4 full: multiply discharge by 1.82 For smoother pipe: multiply discharge and
multiply velocity by 1.13 velocity by 0.015 and
divide by "n" value of
smoother pipe.
426 2003 National Standard Pumbing Code--I/Iustrated

Alphabetical Index
Accessible, FoodHandlingEstablishments,9.1.5
Definition 1.2 Indirect Waste Connections, 14.10.2
Indirect wastes, 9.1.2
Backflow Preventers, 10.5.5
Backwater valves, 5.5 Medical and Other Sterile Equipment, 9.1.7
Base of Stacks e.O., 504.5 Minimum Air Gaps for Plumbing Fixtures,
Table 10.5.2
Dead ends, 2.23
Potable Clear-Water Wastes, 9.1.8
Expansion Joints, 4.1.3
Flushometer Valves, 7.19.5 Relief Valve Discharge Piping, 10.16.6
Interceptors-general, 6.1 Requirements for, 10.5.2
Residential Sink and Dishwasher, 7.15.2
Oil Interceptors, 6.3.2
Residential Sink, Dishwasher, and Food-
Sumps and Ejectors, 11.7
Valve Accessibility, 10.12.9 Waste-Grinder, 7.15.3
Valves in Dwelling Units, 10.1204 Swimming Pools, 9.1.1 I
Water Hammer Arresters, 10.14.7 Vapor vents and stacks for Sterilizer, 14.11
Acid waste. See Special Wastes Waste water discharge, 9.1.10, 904.3
Treatment of Corrosive Wastes, 9.6 Water Treatment Systems 7.22
Adopting agency, Air gap (water),
Definition, 1.2 Definition, 1.2
Authority havingjurisdiction, Automatic clothes washers, 7.13.1
Definition, 1.2 Backflow Prevention Devices, 1O.5.3.A
Requirements for, Appendix F Bidet, 7.7.2
Air break, Connections to Carbonated Beverage
Definition, 1.2 Dispensers, 10.5.8
Air Conditioning Equipment, 9.1.10 - 904.3 Domestic dish washing machines, 7.15.1
Clear water waste, 9.1.8 Over-rim tub filler spout, 7.804
Dish washing machine, 7.15 A Potable Water Inlet Control and Location,
10.8.5
Drinking Fountains and Water Coolers, 9.1.9
Food handling, 9.1.5 Protection for Special Equipment, 10.5.13
For indirect waste piping, 9.1.3 Residential Sink and Dishwasher, 7.15.2
Walk in coolers & freezers, 9.1.6 Tanks and Vats--Below Rim Supply, 10.5.7
Air chambers, American National Standards Institute (ANSI)
Definition, 1.2 Standards, 3.1.3, Table 3.1.3
Air gap (drainage), American Society for Testing and Materials (ASTM)
Definition, 1.2,9.1.3 Standards, 3.1.3, Table 3.1.3
Air Conditioning Equipment, 9.1.10 American Society of Mechanical Engineers (ASME)
Air conditioning equipment, 9.1.10 Standards, 3.1.3, Table 3.1.3, 1404.1
Aspirators, 14.13 American Society of Sanitary Engineering (ASSE)
Clothes washer, 7.13.1 Standards, 3.1.3, Table 3.1.3
Commercial Dishwashing Machine, 7.15 A American Water Works Association (AWW A)
Drainage piping materials, 3.9, 3.10, Standards, 3.1.3, Table 3.1.3
Drinking Fountains and Water Coolers, 9.1.9 Anchors, See Supports
Drinking water treatment units, 10.18.2 Anti-scald valve. See Water Temperature Control
Valve
Floor Drains, 14.10.3

Appliances Bedding. See trenching and bedding.
Materials, 3.3, standards, Table 3.1.3 Bedpan steamer,
Approval of alternate materials, 3.12.2 Definition, 1.2
Approved, Bedpan washer, 14.8
Definition, 1.2 Vents and stacks, 14.9
Appurtenances Boiler blow-off,
Materials, 3.3 Definition, 1.2
Standards, Table 3.1.3, 3.3 Boiler blow off tank,
Area drains, Definition, 1.2
Definition, 1.2 Boilers,
Aspirators, Drains for, 9.1.8
Definition, 1.2,14.13 Bottling establishments,
Autopsy table, Solids Interceptor for, 6.7.2
Definition, 1.2 Branch,
Backfilling, 2.6 Definition, 1.2
Backflow, water distribution Branch, fixture. See Fixture branch
Definition, 1.2 Branch interval,
Protection against, 10.5 Definition, 1.2
Backflow connection, Breakage,
Definition, 1.2 Protection of pipes from, 2.9.1
Backflow drainage, Building,
Backflow preventer Building classification,
Approval, 10.5.4 Building drains,
Installation, 10.5.5 Definition, 1.2
Maintenance and testing, 10.5.6 Selecting size, Table 11.5.1a
Required use, 10.5.3 Storm, 13.1 - 13.9
Standards, Table 3.1.3 Building drains and sewers,
Backpressure backflow, Definition, 1.2
Definition, 1.2 Building sewers, 11.2
Back siphonage Definition, 1.2
Definition, 1.2 Materials, 3.6.3
Protection against, 10.5 Sanitary and storm, 13.1.3
Back-water valve, Separation of water service pipe, 10.6.1
Definition, 1.2 Size, Table 11.5.1A
Baptisteries, 7.18 Storm, 3.7.4
Bar sinks, 9.1.5 Testing methods, 15.5
Basic design circuit (bdc) 8.9.3 Building subdrains,
Bathroom groups, Definition, 1.2
Definitions, 1.2 High water alarms, 11.7.11
Stack venting, 12.1 1.1 Building traps,
Wet venting, 12.10.1-12.10.3 Definition, 1.2,
Bathtubs, Requirements, 5.3.4
Minimum number, Table 7.21.1 Cast Iron Soil Pipe Institute (CISPI)
Waste outlets and overflows, 7.8.2 Standards, 3.1.3,
Battery of fixtures, Cesspool,

Chemical waste. See Special Wastes Contamination, prevention of, BP 15
Treatment of Corrosive Wastes, 9.6 Continuous Flow,
Clean outs, SA Controlled flow storm water system, 13.9
Base of Stacks, 504.5, 8.6 Sizing for continuous or intermittent flows,
Building Drain and Building Sewer Junction, 13.8
504.6 Values for Continuous Flow, 1104.2
Building Sewer,S 04.2 Conversion tables to metric system, Appendix C
Change of Direction, 504.3 Corrosion
Cleanout plugs and caps, 3.3.2 Protection of pipes from corrosive fill, 2.9.2
Cleanout Size. 504.9 Water piping material from velocity and
Cleanout Spacing, 504.1 erosion, B.6.3
Cleanouts for Concealed Piping, 50404 Corrosive wastes. See special Wastes
Cleanouts for drainage pipe, SA Critical level,
Connections to Cleanouts Prohibited, 504.8 Definition, 1.2
Direction of Flow, 504.7 Cross connection,
Manholes for Large Pipes, 504.10 Definition, 1.2.
Clear Water Wastes, Cross Connection Control, 1004.3
Definition, 1.2 Appliances, 10.5.1
Clinic sinks, Backflow Prevention, 10.5, 14.7
Definition, 1.2, Connections to Carbonated Beverage
Installation, 14.8 Dispensers, 10.5.8
Local vent, 14.9 Domestic Water Heat Exchangers, 10.5.11
Clothes washers, 7.13 Hose Connections, 10.5.12
Code, Plumbing Fixtures, 10.5.1
Definition, 1.2 Protection for Special Equipment, 10.5.13
Color coding of water supply, 10.2 Protection from Fire Systems, 10.5.9
Combination fixture, Protection from Lawn Sprinklers and
Definition, 1.2 Irrigation Systems, 10.5.10
Combination waste and vent system, Required Backflow Prevention Devices,
Definition, 1.2,12.17 10.5.3
Commercial Standards (CS), 3.1.3, Table 3.1.3 Sink Faucets, 7.11.5
Conductors Tanks and Vats--Below Rim Supply, 10.5.7
Definition, 1.2 Water Supply Outlets, 10.5.1
Leaders or conductors and connections, 1304 Cultured Marble Institute (CMI)
Materials, 3.7 Standards 3.1.3, Table 3.1.3
Not to be Used Improperly, 13.4.1 Cutting ornotching, 2.9.3
Protection of Rain Water Leaders, 1304.2 Day Care Center,
Size, Table 13.6.1 Definition, 1.2
Use and installation, 1304 Day Nursery,
Connections to water supply system, Definition, 1.2
Availability of Public Water, 2.19.1 Dead ends,
Cross Connection Control, 1004.3,17.15.1, Definition, 1.2,
17.15.2 Avoidance, 2.23
Interconnections, 1004.2 Defective plumbing, 15.7
Private Supplies, 100404 Definitions,
Private Systems, 2.19.2 Plumbing terms, 1.1, - 1. 2
Protection of potable water supply, lOA
Toxic Materials, 1004.5

Trailer park tenns, Chapter 18 Size leaders and conductors, table 13.6.1
Demand for water, Vertical walls, 13.1.10.3
Estimating demand, B.5 Where required, 13.1.1,
Minimum requirements, 10.14 Window wells, 13.1.7
Table 10. 14.2B, Drainage system, sub-building. See building subdrains.
Table B.5 Drains
Developed length, Floor, 7.16
Definition, 1.2 Parking & service garage, 13.1.8,6.3,6.4
Diameter, Roof, 3.3.9,13.5
Definition, 1.2 Dry well. See Leaching well or pit
Directional changes, drainage piping, 2.3 Dwelling unit,
Discharge rates, in sloping drains, Table 11.3.1 Definition, 1.2
Dishwashing machines, 7.15 DWV (drain-waste-vent),
Disinfection of potable water systems, 10.9 Definition, 1.2
Disposal fields, size and spacing, Table 16.9.3- Effective opening,
Distribution box, 16.7 Definition, 1.2
Domestic sewage, Ejectors,
Definition, 1.2 Converting GPM to DFU Values for
Double check valve assembly, Continuous Flow, 11.4.2
Definition, 1.2 Grinder, 11.7.6
Downspout. See Leader. Pneumatic ejectors, 11.7.7, 12.14.3
Drainage fixture unit. See Fixture unit, drainage. Sewage pumps, 11.7.8
Drainage piping. See Drainage system. Sumps and ejectors, 11.7, 11.7.8, 11.7.9
Drainage system High water alanns, 11.7.11
Definition, 1.2 Equipment,
Cleanouts, 5.4 Standards, 3.1.1,3.1.3
Fittings in drainage systems, 2.4 Used and condemned, 2,14,2.15,
In trailer parks, 18.3 Equivalent length,
Materials detrimental to, 2.1 0 Definition, 1.2
Testing methods, 15.4 Erosion, B.6.3
Drainage system, building Existing buildings, 3.12.1
Definition, 1.2, 11.2 Existing work,
Drainage system, sanitary, Definition, 1.2
Discharge rates, Table 11.3.1 Expansionjoints. 4.1.3
Materials, table, 3.1.3, table 3.6, Exposure of work, 15.1
Size selection, 11.5.1 Family,
Slope, 11.3.1 Definition, 1.2
Drainage system, stonn, Federal Supply Service (FS),
Areaway drains, 13.1.6 Standards, 3.1.3, Table 3.1.3
Continuous flow, 13.1.11 Ferrous pipe. See Pipe,
Controlled flow, 13.9 Standards, Table 3.1.3
Foundation drains, 13.5.1 Filters, (sewage) See Sand filter
Leaders or conductors, 13.4 Definition, 1.2
Materials, table 3.1.3, table 3.7 Friction loss allowance,
Parking and service garages, 13.1.8 Copper tube & fittings, B.9.7B
Prohibited connection, 13.1.2 Threaded pipe & fittings, Table B.9.7 A,
Roof drainage, 13.1.1 0 Fixture branch, (drainage)
Roofdrains,13.5 Definition, 1.2 size
Size gutters, table 13.6.3 Sizing, 11.5.1, Table 11.5.1B
Size horizontal drain piping, table 13.6.2

Fixture Drain, definition, 1.2 Lavatory Equivalent, 7.6.5
Fixture branch supply, (water) Load values (d.f.u). Table 11.4.1
Definition, 1.2 Load values, (wsfu), Table I0.I4.2A, Table
Individual outlets, B.3 B.5.2
Maximum flow rates, Table B.3 Location, 2.20.2
Minimum branch sizes, Table 10.14.2A, Material, 7.1
Table B5.2 Minimum number, 7.21, Table 7.21.1,
Minimum flow rates, 10.14.2, Appendix D
Fixture trap, Occupant load, 7.21.2
Fixture trap Size, 5.2, Prohibited locations, 7.12.2
General Requirements, 5.3, Prohibited types, 7.4.7, 7.5.4
Minimum size, Table 5.2, Safety Features for spas and hot tubs, 7.23
Separate traps, 5.1, Separate Facilities, 7.21.4
Fixture unit, (drainage d.f.u.) Showers, 7.10
Definition, 1.2 Sinks, 7.11
Converting Fixtures to d.f.u. Table 11.4.1 Substitution and Omission of Fixtures, 7.21.5
Converting flow to GPM, 11.4.2, Urinals, 7.5
Determining load in d.f.u. 11.4.1, Water closets, 7.4
Diversity factor, 11.4.3 Whirlpool baths, 7.9
Value Curves, Appendix I Flashings, 4.5,12.4.2,13.5.4
Fixture unit, (water supply w.s.f.u.) Flood level rim,
Converting Fixtures to w.s.f.u. Table Flooded,
10.14.2A, Table B.5.2 Definition, 1.2
Converting w.s.f.u. To GPM, Table 10.14.2B Floor drains, See Drains, floor
Determining loads in w.s.f.u. 10.14.3, B5.2 Floor flanges,
Fixture (Plumbing) Materials, 3.3.4
Definition,I.2 Water closet connections, 2.22
Accessibility, 7.2, 7.3.3, 7.21.3, Flow pressure,
Air gaps for, 10.5.2, Table 10.5.2 Definition, 1.2
Automatic clothes washers, 7.13 Flow rates,
Back-to-back,2.3.3 Sloping drains, Appendix K
Bathtubs, 7.8 Water, 10.14.1, Table 10.I4.2B, Tables
Bidets, 7.7 B.7.3. (A to H)
Clearances required, 7.3.2, Figure 7.3.2 Flushing devices, 7.19
Combination Bath/Showers, 7.8.3 Flush tanks, 7.19.3
Dishwashing machines, 7.15 Flushometer tank, 7.19.4
Drinking fountains and water coolers, 7.12 Flushometervalves,7.19.5
Facilities in Mercantile and Business Flushing type floor drain,
Occupancies Serving Customers, 7.21.7 Definition, 1.2
Fixture Requirements for Special Food handling establishments,2.25, 9.1.5
Occupancies, 7.21.6 Food waste grinders, 6.2.3, 7.14, 7.15.3
Fixtures for detention and correctional Footings, protection of, 2.17
institutions, 7.20 Foul air exhaust, BP12
Floor drains, 7.16 Fountains, drinking,
Food Service Establishments, 7.21.8 Compliance, 7.12,
For the handicapped, 7.2 Indirect waste discharge, 9.1.9
Installation, 7.3 Prohibited locations, 7.12.2
Lavatories, 7.6 Requirements for, Table 7.21.1,

Fountains, ornamental, Potable Clear-Water Wastes, 9.1.8
Special installations, 7.18 Relief Valve Discharge Piping, 9.1.12
Freezing, protection from, 2.16 Swimming Pools, 9.1.11
Friction limitation, B.9 Walk-in Coolers and Freezers, 9.1.6
Frost closure, 12.5 Where Indirect Wastes Are Required, 9.1.4
Garbage can washers, 7.1 7 Indirect waste pipe,
Gasoline stations, Definition, 1.2
Exclusion of materials detrimental to the Fixture Traps, 9.2.3
sewage system, 2.10 Installation, 9.2
Oil/Water Separators, 6.3, 6.3.4 Materials and installation, 9.2.1,3.5.1
Special Wastes Sanitary, 9.4 Pipe Size, 9.2.2
Storm Drains, 13.1.8 Indirect waste receptors, 9.3
Grade Drainage Fixture Unit (DFU) Values, 9.3.7
Definition, 1.2 Minimum Receptor Pipe Size, 9.3.6
Gray water, Appendix G Open-hub Drains, 9.3.5
Grease interceptor. See Interceptors, grease Prohibited Locations, 9.3.3
Grease trap. See Interceptors, grease Standpipes, 9.3.4
Grinders, food waste, 6.2.1, 7.14, 7.15.3 Industrial wastes,
Ground water Definition, 1.2
Definition, 1.2 Insanitary,
Protection of, BP22 Definition, 1.2
Hanger, See Supports Installation practices, 2.8
Hazard, definition, 1.2 Installed,
Health hazards, 2.5 Definition, 1.2
Heat transfer fluid (water), 10.4.9 Interceptors,
Heel or side-inlet bends, 2.4.2 Definition, 1.2
Horizontal branch drain, Accessibility, 6.1.6
Definition, 1.2 Design ofInterceptors, 6.1.2
Restriction of connection, 11.9 Exclusion of other liquid wastes, 6.1.3
Horizontal Pipe, General, 6.1.4.1, 3.3.7
Definition, 1.2 Mechanical Equipment, 6.1.4.3
Offsets, 11.6.5 Point of discharge, 6.1.7
Hospitals. See Medical care facilities When Required, 6.1.1
Hot water, BP3 Interceptors grease, 6.1.4.2
Definition, 1.2, Chemicals prohibited, 6.2.7
Hot water supply system, 10.15.1 Commercial Dishwashers, 6.2.4
Hot water heaters and tanks, 10.15.3, 10.15.5 Fixture traps, 6.2.2
House drains. See Building drains Food waste grinders, 6.2.3
House traps. See Building traps Exclusion of other liquid wastes, 6.1.3
Ice making machines, 9.1.5, and 14.6 Location, 6.2.5
Ice storage chests, 9.1.5, and 14.6 Prohibited interceptors, 6.2.6
Increasers, 4.1.4 Sizing Criteria, Appendix J
Indirect Connection (Waste) Sizes up to 50 GPM, 6.2.1
Definition, 1.2 Interceptors sand, 6.4
Air Conditioning Equipment, 9.1.10,9.4.3 Alternate Design, 6.4.4
Drinking Fountains and Water Coolers, 9.1.9 Construction and Size, 6.4.2
Food Handling Establishments, 9.1.5 Water seal, 6.4.3
General, 9.1.1 Where Required, 6.4.1
Medical and Other Sterile Equipment, 9.1.7

Interceptors Solids, 6.5 Detrimental to plumbing system, BP14, 2.14,
Sizing,6.5.c 10.4.5, 10.4.8
Interceptors Special Applications, 6.7 Standards, 3.1.1, Table 3.1.3
International Association of Plumbing and Mechanical May,
Officials (IAPMO) Definition, 1.2
Standards, 3.1.3, Table 3.1.3 Medical care facilities, Chapter 14
Invert, Clinical sinks and bedpan washers, 14.8
Definition, 1.2 Cross connection control and backflow
Joints,4.1.1 prevention, 14.7
Standards, 4.1.2 Floor Drains, 14.10.3
Types of Joints for piping materials, 4.2 General, 14.1,
Brazed, 4.2.8.1 Indirect Waste Connections, 14.10.2
Burned lead, 4.2.10 Local vents and stacks for clinical sinks or
Caulked,4.2.1 bedpan washers, 14.9
Cement mortar, 4.2.9 Material, 14.9.2
Expansion, 4.1.3, 4.2.16 Medical gas and vacuum piping systems, 14.3
Extracted mechanical, 4.2.8.2 Mental Patient Rooms, 14.5
Flared, 4.2.5 Professional Qualifications ofInstallers,
Flexible,4.2.11 Inspectors and Verifiers, 14.3.2
In plastic piping, 4.2.14 slip, 4.2.11, Prohibited locations for ice storage, 14.6
4.2.15 Protrusions from walls, 14.4
Mechanical, 4.2. 11 Provisions for Drainage, 14.9.4
Plastic and other materials, 4.3.9 Required Size and Arrangement, 14.9.3
Soldered, 4.2.4 Sterilizer, 14.10
Split couplings, 4.2.17 Trap Priming, 14.9.5
Threaded, 4.2.2,4.3 .4,4.3.9 Water Service, 14.2 14.13
Welded 4.2. 1 0 Meters, pressure loss, B.9.5
Wiped, 4.2.3 Metric conversion tables, Appendix C
Laundry facilities in trailer parks, 18.8.4 Mixing Valves
Laundry sinks, 7.11.3 Mixed Water Temperature Control, 10.15.6, Table
Lavatories, 7.6, Table 7.21. I 10.15.6
Leaders Mobile home parks, Chapter 18
Definition, 1.2 Motor vehicle garages, See Gas Stations
Materials, Table 3.7 Motor vehicle washing establishments, See Gas
Size, Table 13.6.1 Stations
Traps, 13.3 Mounting bolts, 3.3.4
Use and installation, 13.4 Multiple dwelling,
Light requirements, BP16, 2.20.1 Definition, 1.2
Local ventilating pipe, National Sanitation Foundation International (NSF)
Definition, 1.2 Standards, 3.1.3, Table 3.1.3
Low buildings, simplified water sizing method, B.7, B.8 Neutralizing and Dilution Tanks, 6.6
Main, Non-potable water,
Manholes, 5.4.10 Nuisance,
Manufacturing Standardization Society (MSS) Definition, 1.2
Standards, 3.1.3, Table 3.1.3 Obstruction to flow, 2.4.3
Materials, 3.1 to 3.12, BP9
Alternate materials and methods, 3.12

Offsets Minimum requirements for water distribution
Definitions, 1.2 systems, 10.14
Sizing, 11.6 Pressure, absorbing devices, 10.14.7
Oil/Water Separators (Interceptors), 6.3 interceptors. Variable Street Pressures, 10.14.5
See Interceptors Pressure balancing valve,
Overflows Definition, 1.2
Lavatory, 7.6.4 Pressure tanks, 3.3.8,
Lush tanks, 7.19.3 Pressure relief, 10.8.9
Water supply tanks, 10.8.3, Table 10.8.3 Vacuum relief, 10.8.8,
Overheating, protection from, 2.16 Private sewage disposal systems,
Paved areas, 13.1.1 Definition, 1.2
Percolation test, 16.5 Private sewer, BP6
Piping materials (System) Definition, 1.2
Air conditioning condensate drain piping, 3.9 Private sewer system,
Alternate materials and methods, 3.12 Definition, 1.2
Chemical and special waste systems, 3.11 Private water supply,
Condensate drains from combustion Definition, 1.2
processes, 3. 10 Public sewer, BP6,
Foundation drains and subsoil drainage, 3.8 Definition, 1.2
Potable water piping, 3.4 Public toilet room,
Sanitary drainage piping, 3.5 Definition, 1.2
Storm drainage piping, 3.7 Public water main,
Vent piping, 3.6 Definition, 1.2
Pitch. See Grade Pumps,
Plumbing, Certified Pumps, 17.6.1
Definition, 1.2 Installation, 17.6.2
Plumbing and Drainage Institute (PDII Low Pressure Cut-Off Required on Booster
Standards, 3,13, Table, 3.1.3 Pumps, 10.8.7
Plumbing appliances, Prohibited Location of Potable Supply Tanks,
Definition, 1.2 10.7.2
Plumbing fixtures, Pump Accessories, 17.6.6
Definitions, 1.2 Pump Location, 17.6.4
Plumbing inspector. See Authority Having Jurisdic- Pump Mounting, 17.6.5
tion Pumps and Other Appliances, 10.7.1
Plumbing system, Water Pressure Booster Systems Required,
Pollution, Water pumping and storage equipment, 10.7
Definition, 1.2 Protection against contamination,
Water service near sources of, 10.6.2 Backflow Prevention, 10.5,
Pools, Prohibited Location of Potable Supply Tanks,
Ornamental, 7.18.1 10.7.2
Swimming, definition, 1.2,7.18,9.1.11 Pumps and Other Appliances, 10.7.1
Potable water, BPI, Rainfall. See Precipitation rate
Definition, 1.2 Ratproofing,
Precipitation rate (rainfall), Appendix A Meter boxes, 2.13.2
Pressure, Openings for Pipes, 2.13.3
Excessive Pressures, 10.14.6 Strainer plates, 2.13.1
Inadequate Water Pressure, 10.14.4

Readily accessible, Sand interceptor. See Interceptors
Definition, 1.2 Sanitary facilities in trailer parks, 18.8
Building Valve, 10.12.2 Sanitary sewer,
Individual Fixture Valves, 10.12.6 Definition, 1.2
Manifolds, 10.17.3 S.D.R.,
Trap Priming, 5.3.6 Definition, 1.2.
Receptors, See indirect Waste Receptors Plastic Piping, 3.5.4
Reduced pressure principal back-pressure Seepage pits, 16.5.5, 16.5.6, 16.8
backflow preventer, Septic Tanks,
Definition, 1.2 Definition, 1.2,3.3.11
Installation of Backflow Preventers, Sewage,
10.5.5 Definition, 1.2
Maintenance and Testing of Backflow Sewage disposal systems, BP 17
Prevention Devices, 10.5.6 Private, Chapter 16
Protection for Special Equipment, 10.5.13 Sewage ejectors Pneumatic,
Protection from Fire Systems, 10.5.9 Definition, 1.2, See Ejectors
Protection from Lawn Sprinklers and Sewage Pump
Irrigation Systems, 10.5.10 Definition, 1.2, See Ejectors
Required Backflow Prevention Devices, High water alarms, 11.7.11
10.5.3 Sewer system, flooding prevention, BP 18
Reducers, 4.1.4 Sewer system, private, 2.19.2
Relief valves. See Valves, relief Sewer storm,
Relief vents. See Vents, relief Definition, 1.2
Revent pipe. See Vents, individual Shall,
Rim , Definition, 1.2
Definition, 1.2 Shock arrestor,
Riser, Definition, 1.2
Definition, 1.2 Showers, 7.10
Roof drains, In trader parks, 18.8.3
Definition, 1.2 Location of Valves and Shower Heads,
Roof gutters, size, Table 13.6.3 7.10.8
Roughing-in, Minimum number, Table 7.21.1
Definition, 1.2 Mixed temperature control, 10. 15.6
Safety devices, BP 5, Shower Compartments, 7.10.5
Combination Pressure-Temperature Relief Shower Floors or Receptors, 7.10.6
Valves, 10.16.4 Shower Waste Outlet, 7.10.4
Pressure Relief Valves, 10.16.2 Water Conservation, 7.10.2
Pressure tanks, 3.3.10, and 10.16.1 Water Supply Riser, 7.10.7
Relief Valve Discharge Piping, 10.16.6 Sinks,
Replacement of Relief Valves, 10.16.8 Clinical sinks and bedpan washers, 14.8
Temperature Relief Valves, 10.16.3 Kitchen sinks, 7.11.2
Thermal Expansion Control, 10.15.7 Required Size and Arrangement, 14.9.3
Vacuum Relief Valves, 10.16.7 Service sinks, 7.11.4
Safety hazards, 2.5, 2.7 Sizing of building water supply system, Appendix B
Safety precautions for hazardous operations, 2.6.8 Slaughterhouses, 6.7.3
Sand filters, Sleeves, 2.12
Definition, 1.2, Slope, See Grade.
Sewage disposal system, 16.12 Soil character of, 10.11

Soil pipe, Sumps,
Definition, 1.2 Definition,1.2
Special design plumbing system, Appendix E Venting, 12.14.2
Special wastes, Supply fixture unit (Water).
Definition, 1.2 Definition, See fixture unit, water supply
Special waste systems, 3.11 w.s.f.u.
Treatment of Corrosive Wastes, 9.6 Supports,
Sprinklers, Lawn, 10.5.10 Definition, 1.2
Stack, Hangers and Supports, 8.1 - 8.8
Definition, 1.2 Material, 804
Stack vent, Standards, Table 3.1.3
Definition, 1.2, Swimming pools,
Reduction, 11.5.7, Definition, 1.2,
Stack Vents and Vent Stacks, 12.3.1, Cross Connection, 7.18
12.11 Indirect Waste, 9.1.11,
Sterilizers 14.10 Tanks,
Floor Drains, 14.10.3 Flush Tanks, 7.19.3
Indirect waste connections, 14.10.2 FlushometerTanks,1.19A
Material, 14.11.2 Neutralizing and Dilution Tanks, 6.6
Provisions for Drainage, 14.1104 Pressure Tanks and Vessels, 3.3.8
Required Size and Arrangement, 14.11.3 Septic Tanks, 3.3.11
Vapor vents and stacks, 14.11 Waste oil tanks, 6.3
Storm drains. See Building drains, storm Temperature. See Water temperature control valve
Storm sewer, Tempered water,
Strainers Testing, BP 13, Chapter 15
For indirect waste receptors, 9.3.2 Tests of alternate materials,
Forroof drains, 13.5.2, 13.5.3 Tests, 3.12 - 3.12.5
In fixtures, 7.16.2 Thermostatic/pressure balancing valve, combination,
Structural safety, BP21, 2.9.3 Definition, 1.2
Subsoil drain, Thermal Expansion Control, 10.15.7
Definition, 1.2 Toilet facilities,
Suction line, For workers, 2.24,
Definition, 1.2 Minimumnumberrequired, 7.21, Table7.21.1
Suds pressure zones, 11.11 Water Closets.
Exceptions, 11.1104 Floor Flanges and Mounting Bolts, 3.3 A
General, 11.11.1 Prohibited Water Closets, 704.7
Locations in Stacks Serving Suds- Supporting Wall-Hung Fixtures, 7.3.5
Producing Fixtures, 11.11.2 Water closet connections, 2.22
Separate Stacks, 11.11.3 Water closets, 7A
Suds venting, 12.15 Water Conservation, 704.2
Sump pump, Trap arm,
Definition, 1.2 Definition, 1.2,
Air Conditioning Condensate, 904.3 Maximum length of trap arm, Table 12.8.1
High water alarms, 11.7.11 Trap primer,
Foundation Drains, 13.1.5 Definition, 1.2
Sizing for continuous or intermittent flows,
13.8

Trap seals Temperature relief, 10.16.1, 10.16.3,
Trap seals, 5.3.2 Vacuum relief, 10.8.8, and 10.16.7
Trap setting and protection, 5.3.3, BP II Water heating equipment, 10.12.7
Trap seal maintenance, 5.3.6 Water supply control, 10.12
Protection required, 12.2.1 Vats, 10.5.7
Traps, Velocity limitation, 10.14.1, B.6
Definition, 1.2, Venting systems
Separate traps, 5.1 Definition, 1.2
Size oftraps, 5.2, Table 5.2, 13.3 Aggregate Size of Vent Terminals, 12.16.6
Travel trailer parks, Chapter 18 Circuit and loop venting, 12.13
Trenching and bedding, 2.6.1,2.17 Combination waste and vent system, 12.17
Tunneling, 2.6.5 Connections to Conventional Drainage
Underground installation. See Trenching and Systems, 12.17.8
bedding. Extension above Roofs, 12.4.1
Underwriter's Laboratory (UL) Extensions outside Building, 12.4.6
Standards 3.1.3, Table 3.1.3 Extensions through Wall, 12.4.5
Urinals, 7.5 Fixturereventing,12.12
Minimum number, Table 7.2 1.1 Fixtures Drains Connected at Different
Prohibited types, 7.5.4 Levels, 12.9.2
Water conservation, 7.5.2 Frost closure, 12.5
Vacuum, Height above Fixtures, 12.6.3
Definition, 1.2 Horizontal Branches, 12.12.2
Pressure Tanks-Vacuum Relief, 10.8.8 Horizontal Offsets in Stacks Having Ten or
Vacuum breakers, More Branch Intervals, 12.3.3
10.5.3,14.7 In medical care facilities, 14.9,14.11
Vacuum systems central, 14.12 Individual Vent as Common Vent, 12.9.1
Valves, Location of Vent Terminal, 12.4.4
Accessibility 10.12.9 Materials, 3.6.
Anti-scald, 10.15.6 Other designs, 12.18
Backwater, 5.5 Other Use Prohibited, 12.3.5
Building, 10.12.2 Pipe Sizing, 12.17.4
Combination pressure-temperature- relief, Pneumatic Sewage Ejectors, 12.14.3
10.16.4 Protection of trap seals, 12.2
Curb, 10.12.1 Reliefvent for building sewer, 12.19
Double check, 10.5.3 Relief Vents for Stacks Having Ten or More
Dwelling units, 10.12.4 Branch Intervals, 12.3.2
Flush, 7. 19.3 Size and length of fixture vents, 12.16
Flushometer,7.19.5 Size of Stack Vents and Vent Stacks, 12.16.4
Friction loss allowance, Table B.9.7 A, Stack venting, 12.11
Table B.9.7B Stack Vents and Vent Stacks, 12.3.1
Individual fixture, 10.12.6 Suds pressure venting, 12.15
Mixed water temperature, 10.15.6 Sump Pits, 12.14.2
Pressure reducing, 10.14.6 Testing methods, 15.4
Pressure relief, 10.16.1, 10.16.2, 10.16.3, Underground Vent Piping, 12.16.7
10.16.6, and 10.8.9 Vent Headers, 12.3.4
Riser, 10.12.5 Vent Size, 12.19.2
Stop-and-waste, 10.6.3

Vent Slope, 12.6.1 Protection of potable water supply,
Vent Washdown, 12.12.4 10.4
Venting of building subdrain systems, Quality of water supply, 10.1
12.14 Sizing Water Distribution Piping,
Venting of drainage stacks, 12.3 10.14.3
Venting of Fixture Drains, 12.8.1 Variable Street Pressures, 10.14.5
Vertical Rise, 12.6.2 Water Hammer, 10.14.7
Waste Stacks Serving Kitchen Sinks, Water pressure booster systems, 10.8
12.10.5 Water pumping and storage
Waterproof Flashings, 12.4.2 equipment, 10.7
Wet venting, 12.10 Water required, 10.3
Wall hung water closet, Water service, 10.6
Definition, 1.2 Water supply control valves, 10.12
Washers, Water supply system materials See
Automatic clothes, 7.13,1 Section 3.8.
Garbage can, 7.17 Water (hot),
Washroom requirements, 2.20 Combination Pressure-Temperature
Waste pipe, Relief Valves, 10.16.4
Definition, 1.2 Drainage of Hot Water Storage
Wastes Tanks, 10.15.4
Clear water, 9. 1.8 Drip Pans, 10.15.9
Industrial, 2.1 0.2 Hot Water Supply System, 10.15.1
Minimum size, 11.5.2 Minimum Requirements for Hot Water Storage
Special, 9.4 Tanks, 10.15.3
Water (ground) Mixed Water Temperature Control, 10.15.6
Definition, 1.2 Plastic Piping, 10.15.8
Water (potable) Pressure Marking of Hot Water Storage Tanks,
Backflow prevention, 10.5 Pressure Relief Valves, 10.16.2
Basic design circuit (bdc), B.9.3 Relief Valve Discharge Piping, 10.16.6
Excessive Pressures, 10.14.6 Replacement of Relief Valves, 10.16.8
Flushing and disinfecting potable water Tank Protection, 10.16.1
systems, 10.9 Temperature Maintenance Where Required,
Identification of potable and 10.15.2
non-potable water, 10.2 Temperature Relief Valves, 10.16.3
Inadequate Water Pressure, 1O.14.4 Thermal Expansion Control, 10.15.7
Maximum Velocity, 1O.14.1,B.6 Vacuum Relief Valves, 10.16.7
Minimum requirements for water Water Heaters Used for Space Heating,
distribution systems, 10.14 10.15.10
438 2003 National Standard Fwnbing Code-l!/ustrated

NOTES

NOTES

National Standard Plumbing Code

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

National Standard Plumbing Code

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

National Standard Plumbing Code

Uploaded by

Copyright:

Available Formats

2003

All inquiries or questions relating to interpretation should be forwarded to

~ 2003 Plumbing- Heating-Cooling Contractors-National Association

National Standard Plumbing Code

The development of a recommended code of plumbing practice, design, and installation,

In case of practical difficulty, unnecessary hardship or new developments, exceptions to the

Comments on Code Text

All changes from the previous edition of this Code are

J. Richard Wagner,PE,Chairman Thomas C. Pitcherello Robert Kordulak, NSPC Secretariat

Frank R.Maddalon RichardD. Wagner,PE

ADM 1.2 SCOPE

ADM 1.3 PURPOSE

ADM 1.4 APPLICABILITY

1.4.1 Addition or Repair

1.4.2 Existing Plumbing Installation

1.4.3 Existing Use

1.4.4 Maintenance and Repairs

1.4.5 Change of Building Use

1.4.6 Moved Buildings or Structures

2003 National Standard PUl11hingCode-Illustrated 1

ADM 1.5 APPROVALS

1.5.2 Authority Having Jurisdiction

1.5.3 Tests Required

1.5.4 Test Procedure

ADM 1.6 ORGANIZATION AND ENFORCEMENT

1.6.1 Authority Having Jurisdiction

2 2003 National Standard Pumbing Code-Illustrated

1.6.4 Stop Work Order

1.6.5 Authority to Condemn

1.6.6 Authority to Abate

1.6.8 Work Prior to Permit

ADM 1.7 VIOLATIONS AND PENALTIES

2003 National Standard Pumbing Code-Illustrated 3

ADM 1.8 PERMITS

1.8.1 Permits Required

1.8.2 Permits Not Required for the Following

ADM 1.9 PROCESS FOR OBTAINING PERMITS

4 2003 National Standard Pumbing Code-1I/ustrated

1.9.4 Permit Issuance

1.9.5 Approved Plans

1.9.6 Plans Retention

1.9.7 Permit Validity

1.9.8 Permit Expiration

1.9.9 Revocation or Suspension

ADM 1.10 PERMITS

2003 National Standard Pumbing Code-Illustrated 5

1.10.3 Plan Review Expiration

1.10.4 Work Without a Permit

1.10.5 Refunding of Fees

ADM 1.11 INSPECTIONS

1.11.1 Required Inspections

1.11.3 Use of Existing Plumbing

6 20()3 National Standard Pumbing Code-Illustrated

1.11.5 Requests for Inspection

1.11.6 Other Inspections

1.11.7 Reinspection Fees

ADM 1.12 FINAL CONNECTIONS

1.12.1 Energy or Fuel