32 D 44 e
32 D 44 e
32 D 44 e
SERVICE MANUAL
No. S38F8LC32D44E
MODELS LC-32D44E/S/RU-BK/GY
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its orig-
inal condition and only parts identical to those specified should be used.
CONTENTS
SAFETY PRECAUTION [10] Initialization to factory settings.....................3-24
IMPORTANT SERVICE SAFETY PRE- [11] Lamp error detection ...................................3-24
CAUTION ............................................................i [12] Public Mode (Hotel Mode) ...........................3-25
PRECAUTIONS A PRENDRE LORS DE
LA REPARATION ...............................................ii CHAPTER 4. TROUBLE SHOOTING TABLE
PRECAUTIONS FOR USING LEAD-FREE [1] TROUBLE SHOOTING TABLE .....................4-1
SOLDER ........................................................... iii
CHAPTER 5. MAJOR IC INFORMATIONS
CHAPTER 1. SPECIFICATIONS [1] MAJOR IC INFORMATIONS .........................5-1
[1] SPECIFICATIONS ......................................... 1-1
[2] OPERATION MANUAL .................................. 1-2 CHAPTER 6. BLOCK DIAGRAM/OVERALL WIRING
[3] DIMENSIONS ................................................ 1-5 [1] BLOCK DIAGRAM.........................................6-1
[2] SYSTEM BLOCK DIAGRAM .........................6-3
CHAPTER 2. REMOVING OF MAJOR PARTS [3] OVERALL WIRING DIAGRAM ......................6-4
[1] REMOVING OF MAJOR PARTS ................... 2-1
CHAPTER 7. PRINTED WIRING BOARD ASSEM-
CHAPTER 3. ADJUSTMENT BLIES
[1] After replacement of any PWB and/or IC for [1] MAIN Unit ......................................................7-1
repair, note the following. ............................... 3-1 [2] R/C, LED Unit ................................................7-5
[2] SOFTWARE UPDATING................................ 3-1 [3] MINI AV Unit ..................................................7-6
[3] Entering and exiting the adjustment pro- [4] KEY ...............................................................7-7
cess mode.................................................... 3-18
[4] Remote controller key operation and de- CHAPTER 8. SCHEMATIC DIAGRAM
scription of display in adjustment process [1] DESCRIPTION OF SCHEMATIC DIA-
mode. ........................................................... 3-18 GRAM............................................................8-1
[5] Adjustment process mode menu.................. 3-19 [2] SCHEMATIC DIAGRAM ................................8-2
[6] Special features............................................ 3-20
[7] Video signal adjustment procedure.............. 3-21 Parts Guide
[8] White Balance Adjustment ........................... 3-22
[9] Adjusting procedure by use of [RS-232C] ...... 3-23
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
WARNING Use an AC voltmeter having with 5000 ohm per volt, or higher, sen-
sitivity or measure the AC voltage drop across the resistor.
1. For continued safety, no modification of any circuit should be
attempted. Connect the resistor connection to all exposed metal parts having a
return to the chassis (antenna, metal cabinet, screw heads, knobs
2. Disconnect AC power before servicing.
and control shafts, escutcheon, etc.) and measure the AC voltage
drop across the resistor.
All checks must be repeated with the AC cord plug connection
C A U T I O N : F O R C O N T I N U E D PROTECTION reversed. (If necessary, a nonpolarized adaptor plug must be used
AGAINST A RISK OF FIRE REPLACE ONLY WITH only for the purpose of completing these checks.)
SAME TYPE FUSE. Any reading of 1.05 V peak (this corresponds to 0.7 mA peak AC.)
or more is excessive and indicates a potential shock hazard which
F7101, F7103 (250V 3.15A) must be corrected before returning the monitor to the owner.
F7102 (250V 1A)
DVM
AC SCALE
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard) 1.5k ohm
10W
Before returning the receiver to the user, perform the following
safety checks:
3. Inspect all lead dress to make certain that leads are not pinched,
and check that hardware is not lodged between the chassis and
other metal parts in the receiver. 0.15 F
4. Inspect all protective devices such as non-metallic control knobs, TEST PROBE
insulation materials, cabinet backs, adjustment and compartment
covers or shields, isolation resistor-capacitor networks, mechanical
insulators, etc.
5. To be sure that no shock hazard exists, check for leakage current in
the following manner. TO EXPOSED CONNECT TO
METAL PARTS KNOWN EARTH
Plug the AC cord directly into a 220~240 volt AC outlet. GROUND
Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-
leled by a 0.15F capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as electrical conduit or elec-
trical ground connected to an earth ground.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
Many electrical and mechanical parts in LCD color television have For continued protection, replacement parts must be identical to those
special safety-related characteristics. used in the original circuit.
These characteristics are often not evident from visual inspection, nor The use of a substitute replacement parts which do not have the same
can protection afforded by them be necessarily increased by using safety characteristics as the factory recommended replacement parts
replacement components rated for higher voltage, wattage, etc. shown in this service manual, may create shock, fire or other hazards.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by and shaded areas in the Replacement Parts
List and Schematic Diagrams.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
i
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
Ne peut effectuer la rparation qu' un technicien spcialis qui s'est parfaitement accoutum toute vrification de scurit et aux
conseils suivants.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
AVIS POUR LA SECURITE
De nombreuses pices, lectriques et mcaniques, dans les tlvi- Pour assurer la protection, ces pices doivent tre identiques celles
seur ACL prsentent des caractristiques spciales relatives la s- utilises dans le circuit d'origine. L'utilisation de pices qui n'ont pas
curit, qui ne sont souvent pas videntes vue. Le degr de protec- les mmes caractristiques que les pices recommandes par l'usine,
tion ne peut pas tre ncessairement augmente en utilisant des indiques dans ce manuel, peut provoquer des lectrocutions, incen-
pices de remplacement talonnes pour haute tension, puissance, dies, radiations X ou autres accidents.
etc.
Les pices de remplacement qui prsentent ces caractristiques sont
identifies dans ce manuel; les pices lectriques qui prsentent ces
particularits sont identifies par la marque " " et hachures dans la
liste des pices de remplacement et les diagrammes schmatiques.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
ii
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
PRECAUTIONS FOR USING LEAD-FREE SOLDER
Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
Soldering
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 C which is higher than the conventional lead solder by 40 C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
PRICE PART
PARTS CODE DESCRIPTION
RANK DELIVERY
ZHNDAi123250E BL J 0.3mm 250g (1roll)
ZHNDAi126500E BK J 0.6mm 500g (1roll)
ZHNDAi12801KE BM J 1.0mm 1kg (1roll)
iii
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
LC32D44E-BK
CHAPTER 1. SPECIFICATIONS Service Manual
[1] SPECIFICATIONS
As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of production
units. There may be some deviations from these values in individual units.
NOTE
Refer to inside back cover for dimensional drawings.
Optional accessory
The listed optional accessories are available for the Part name Part number
LCD colour TV. Please purchase them at your nearest
shop. Wall mount bracket
AN-37AG5
Additional optional accessories may be available in near (LC-32D44E, LC-32D44S)
future. When purchasing, please read the newest catalogue
for compatibility and check the availability.
11
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
[2] OPERATION MANUAL
Bilingual
NICAM CH A, NICAM CH B, Bilingual CH A, CH B, CH AB
NICAM CH AB, MONO
Monaural MONO
Monaural NICAM MONO, MONO
NOTE
When no signal is input, the sound mode will display MONO.
12
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
TV (Front view)
TV (Rear view)
MENU button
P( / )
(Programme [channel] buttons) (Input button)
10
6
1
8
2
9 11 13
3 4 5
12
NOTE
Only if you use an active terrestrial antenna, select On (5V) under Supply Voltage.
13
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Appendix
Troubleshooting
Problem Possible Solution
No power. Check if you pressed on the remote control unit.
If the indicator on the TV lights up red, press .
Is the AC cord disconnected?
Check if you pressed on the TV.
Unit cannot be operated. External influences such as lightning, static electricity, etc., may cause improper
operation. In this case, operate the unit after first turning the power off, or
unplugging the AC cord and re-plugging it in after 1 or 2 minutes.
Remote control unit does not Are batteries inserted with polarity (+, -) aligned?
operate. Are batteries worn out? (Replace with new batteries.)
Are you using it under strong or fluorescent lighting?
Is a fluorescent light illuminated to remote control sensor?
Picture is cut off. Is the image position correct?
Are screen mode adjustments (4:3 Mode/WSS) such as picture size made
correctly?
Strange colour, light colour, or Adjust the picture tone.
dark, or colour misalignment. Is the room too bright? The picture may look dark in a room that is too bright.
Check the colour system setting.
Check the HDMI Setup setting.
Power is suddenly turned off. The units internal temperature has increased.
Remove any objects blocking vent or clean.
Check the power control setting.
Is sleep timer set? Press SLEEP on the remote control unit until it sets to Off.
No picture. Is connection to other components correct?
Is input signal type selected correctly after connection?
Is the correct input source selected?
Is non-compatible signal being input?
Is picture adjustment correct?
Is the antenna connected properly?
Is On selected in Audio Only?
No sound. Is the volume too low?
Make sure that headphones are not connected.
Check if you pressed on the remote control unit.
The DTV menu screen is displayed Check if Monochrome is set to On. If so, set it to Off.
in monochrome and hard to select
the item.
The TV sometimes makes a This is not a malfunction. This happens when the cabinet slightly expands and
cracking sound. contracts according to change in temperature. This does not affect the TVs
performance.
14
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
[3] DIMENSIONS
699.2
699,2
575.0
575,0
523.0
523,0
393.8
393,8
332.0
332,0
402.0 230.0
52.0
52,0
402,0 230,0
200.0
200,0
110.0
110,0
200.0
200,0
15
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
LC32D44E-BK
Service
CHAPTER 2. REMOVING OF MAJOR PARTS Manual
2. Remove the 3 lock screws 2 , 6 lock screws 3 , 2 lock screw 4 and detach the Rear Cabinet.
Rear Cabinet
2
Front Cabinet
Stand
21
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
3. Remove the 3 lock screws 5A , 2 lock screws 5B , 1 lock screws 6 and detach the Main Shield.
4. Disconnect all the connectors from all the PWBs.
5. Remove the KEY Unit Ass'y 7 .
6 5A
5B Main Shield
Operation Button 7
KEY Unit
[KM] [LB]
[FPC]
[PD]
[KM]
[LB]
[PD]
[RA] [SP]
SP-R SP-L
22
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
MINI AV Cover
11
12 Main Unit
10
Power/Inverter Unit
MINI AV Unit
9 Speaker(R) 8 Speaker(L)
23
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
11.Remove the 4 lock screws 14 and detach the Stand Fix Angle.
15 R/C,LED Unit 14
Bottom Cover
13
24
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
13.Remove the 6 lock screws 16 and detach the LCD Panel Module.
14.Remove the 2 lock screws 17 and detach the LCD Fix Angle-A.
15.Remove the 2 lock screws 18 and detach the LCD Fix Angle-B.
16.Remove the 8 lock screws 19 and detach the Panel Fix Angle.
16 16
19
19
16 18
17
16
16
LCD Fix Angle-A LCD Fix Angle-B
16 17 18
25
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
LC32D44E-BK
CHAPTER 3. ADJUSTMENT Service Manual
[1] After replacement of any PWB and/or IC for repair, note the following.
When replacing the following units, be sure to prepare the new units loaded with updated software.
MAIN-UNIT: DUNTKE449FM02
Note that an IC into which ROM data is written is available for MAIN-UNIT servicing (see below)
Computer TV set
TV Set
RS-232C
IOIOI
Before using RS-232C updating method is necessary to configure a Terminal PC software. HyperTerminal has been selected as a Terminal soft-
ware because its include in all Windows versions as an accessory, and you can find it inside Accessories\Communications folder. For this rea-
son, please follow carefully the next steps:
1) First time HyperTerminal is used, its necessary to configure some settings. Follows next action to configure two connection: low speed
(9600bps) and high speed (115200bps).
2) Create a New Connection file with name P55_9600bps.
3) Select a free COM port and select the Port Settings properties as follows:
31
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
4) Click on File\Properties menu for selecting the General and ASCII properties as follows:
32
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
1) Check the connection between TV set and PC, sending a wrong command, as for example: aaa. TV set returns an ERR label as an syntaxis
ERROR (Not correct order or sequence).
2) Send the command DWMD to enter TV set in Download Mode. The TV set answer sending same symbol continuosly. If this symbol character
doesnt appear, please dont worry and pass to next step.
3) Close this connection and open P55_115200bps connection clicking over the P55_115200bps that you can find in START\All pro-
grams\Accessories\ Communications\HyperTerminal\HyperTerminal folder.
4) Using Transfer\Send file... menu, select desired file (.bin format) and the transmission protocol (Xmodem) as show below.
6) When flash update process finishes, the Flash Programming Complete label appears in the screen, the device automatically go to switch off,
and in a few seconds go to switch on again.
33
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
2. RS-232C Method Description (Tera Term)
The hardware tools requirement are:
1. A Modem-null (Cross type) DB9 female to DB9 female cable.
2. Make the connections as indicated in the figure:
Computer TV set
TV Set
RS-232C
IOIOI
Software requirements:
To upgrade VCTp software from RS-232C external connector is necessary to use a Tera Term (Pro) free software.
The URL of Tera Term home page is:
http://hp.vector.co.jp/authors/VA002416/teraterm.html
(The address may be changed in future)
Tera Term (Pro) supported operating systems:
MS-Windows 95 or upper
MS-Windows NT 3.5 and 4.0 or upper
Note.- For Windows 3.1 use Tera Term version 1.X.
Copy all the distribution files to an empty floppy disk or temporary directory (for example C:\ TEMP).
Run SETUP.EXE and follow the instruction given by it.
After the installation, the distribution? les are no longer needed, you can delete them or may keep them in the floppy disk.
How to use Tera Term Pro:
When the Tera Term (Pro) program is used, its necessary to shape some settings. Follows next action to configure the connection:
34
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
1) Select: SerialCOM X O.K.
2) Select: Terminal
35
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
4) Select: Setup Serial port O.K. Appear the follow screen:
6) Check the connection between TV set and PC, sending a wrong command, as for example: aaa. TV set returns an err label as an syntaxes
ERROR (Not correct order or sequence).
Send a DWMD (capital letters) command to enter TV set in Download Mode.
Change a baud rate to 115200.
Select: Setup Baud rate 115200 O.K.
36
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
7) Select: File Transfer XMODEM Sent
37
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
10)When flash update process finishes, the Flash programming complete label appear in the screen, the device automatically go to switch off, and
in a few seconds go to switch on again.
Computer
TV Set
(CI Terminal)
TV Set RS-232C
IOIOI
~
~
Jig
Software requirements:
1. Winupload application software on PC.
38
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
How to setup the Winupload software for the first time:
1. Start Winupload. It will appear the following picture.
2. Select the most suitable RS232 Serial Port from Port Setting - Process Menu.
39
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
3. Establish connection on Winupload Software.
5. Select and open the .urt data file from data directory
NOTE: Consider the version shown below just an example, may be is not the latest one, and could be different depending on the TV set destination
(market/Country) or model.
6. Switch On the TV Set (previously in DTV Mode). The Uploading Process starts automatically.
3 10
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
While the TV set is uploading the software, the following information is shown on the TV set screen.
Then, data transfer from PC to TV set finishes when the Upload progress completed label appears in the Winupload screen. Now, the TV set made
some additional verification (Items #2 to #7). When the full uploading process is finished, in the Winupload window appears the label Preparing to
start application for a new TV Set, and just now, in the TV screen of the updated set, appears a congratulations label (Item #8).
NOTE: Do not turn off the TV set while the software updating was in progress.
7. Unplug the AC cord.
8. Disconnect the Jig from TV Set.
Software Version verification procedure.
1. Connect the AC cord and Switch On the TV Set.
2. Select DTV Menu on TV Set. The following On Screen Display will appear.
NOTE: Consider the version shown above just as example, may be is not the latest one, and could be different depending on the TV set destination
(market/Country) or model.
3 11
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
4. Software Version Upgrade Using Card
1. Write the software (ATV and DTV) on the PCMCIA CARD by following the procedure described in the separate document, How to write software
(ATV and DTV) to PCMCIA CARD.
(* In the document, both ATV and DTV are written; you may write either of them.)
(You can equally use any version after Storage Media Manager Version 1.3.1.)
2. Turn off the power.
(* You can select either of the mode ATV or DTV. In this document, ATV is selected.)
3. Insert the PCMCIA CARD with the upper side facing up into the card slot.
(* Do not insert the card with the upper side facing down.)
4. Turn on the power. After a short time, the message, SYSTEM SOFTWARE UPDATE IN PROGRESS. ...) appears and the software upgrade
starts.
If the ATV software upgrade is necessary, the step proceeds to (5); if unnecessary, the DTV software upgrade starts and the step proceeds to (7).
5. If the ATV software upgrade is necessary, the following display appears and the upgrade starts.
When the status bar reaches 100 %, the ATV upgrade is complete. Then the system restarts from the ATV mode. The step proceeds to (6).
3 12
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
6. The message, SYSTEM SOFTWARE UPDATE IN PROGRESS. ... appears again and the DTV software upgrade starts. Then the step proceeds
to (7).
7. After a short time, the message, Congratulations! ... appears. The upgrade is complete.
(Note: You cannot downgrade the ATV software but can downgrade the DTV software.)
3 13
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
3 14
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
3 15
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
3 16
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
3 17
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
[3] Entering and exiting the adjustment process mode
1) Unplug the AC power cord of running TV set to force off the power.
2) While holding down the VOL (-) and INPUT keys on the set at once, plug in the AC power cord to turn on the power.
The letter appears on the screen.
3) Next, hold down the VOL (-) and P( ) keys on the set at once.
Multiple lines of orange characters appearing on the screen indicate that the set is now in the adjustment Process mode.
If you fail to enter the adjustment process mode (the display is the same as normal startup), retry the procedure.
4) To exit the adjustment process mode after the adjustment is done, unplug the AC power cord to force off the power. (When the power is turned off
with the remote controller, once unplug the AC power cord and plug it in again. In this case, wait 10 seconds or so before plugging.)
Caution: Use due care in handling the information described here lest the users should know how to enter the adjustment process mode.
If the settings are tampered with in this mode, unrecoverable system damage may result.
[4] Remote controller key operation and description of display in adjustment process mode.
1. key operation
* Input mode is switched automatically when relevant adjustment is started so far as the necessary input signal is available.
2. Description of display
(5) Destination
3 18
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
[5] Adjustment process mode menu
The character string in brackets [ ] will appear as a page title in the adjustment process menu header.
3 19
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
3 20
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
[7] Video signal adjustment procedure
* The adjustment process mode menu is listed in Section 5.
1. Signal check
1. Signal generator level adjustment check (Adjustment to the specified level)
3. RF AGC adjustment
100% white
2 Auto adjustment Adjustment process Bring the cursor on [ RF AGC ADJ] and press [OK]
performance Page3 [***OK***] appears when finished.
2 Auto adjustment Adjustment process Bring the cursor on [ PAL + TUNER ADJ] and press [OK]
performance Page3 [***OK***] appears when finished.
3 21
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
5. ADC adjustment (Component 15K)
[Terminal]
EXT5 COMPONENT IN
2 Auto adjustment Adjustment process Bring the cursor on [ COMP15K ADJ] and press [OK]
performance Page4 [***OK***] appears when finished.
1) Display the current adjustment status at point 6. (Page 8/11 of process adjustment)
The display for checking the adjustment status is toggled by pressing the 6 button on the remote control.
(Normal OSD display 6 display for check (OSD disappears) 6 normal OSD display )
2) Read the value of the luminance meter.
3) Change M GAMMA R6/M GAMMA B6 (Adjustment offset value) on page 9/11 of process adjustment so that the values of the luminance meter
approach x = 0.272 and y = 0.277.
(Basically, G is not changed. If adjustment fails with R and B, change G. When G is lowered, the weaker of R and B must be fixed.)
4) If G is changed in step 3), change the values of M GAMMA G1-M GAMMA G5 on pages 8/11 and 9/11 of process adjustment as follows. When not
changed, go to step5).
Offset value of M GAMMA G1 = (Offset value of M GAMMA G6) * (160/960)
Offset value of M GAMMA G2 = (Offset value of M GAMMA G6) * (320/960)
Offset value of M GAMMA G3 = (Offset value of M GAMMA G6) * (480/960)
Offset value of M GAMMA G4 = (Offset value of M GAMMA G6) * (640/960)
Offset value of M GAMMA G5 = (Offset value of M GAMMA G6) * (800/960)
5) Display the adjustment status of the current point 5. (Each time the 5 button on the remote control is pressed, the adjustment status check dis-
play is toggled.)
(Normal OSD display 5 Check display (OSD disappears) 5 Normal OSD display )
Change M GAMMA R5/M GAMMA B5 (adjustment offset value) on page 9/11 of process adjustment so that the values of the luminance meter
approach x = 0.272 and y = 0.277.
6) Repeat step 5) for points 4, 3, 2, and 1.
3 22
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
[9] Adjusting procedure by use of [RS-232C]
1) Get ready the PC with COM port (RS-232C) running on Windows 95/98/ME/2000/XP operating system, as well as the RS-232C cross cable.
2) Start the unit with the RS-232C cable connected.
3) Start the terminal software. (The freeware readily available on the Internet will do.)
4) Make the following settings.
5) If the settings are correct, the terminal software indicates "ERR" against pressing of the "ENTER" key.
6) After the settings are done correctly, it is possible to make an adjustment by typing in the command shown in the table below and pressing the
"ENTER" key on the keyboard.
7) Command entry is successful if the terminal software indicates "OK" when the "ENTER" is pressed. If "ERR" is shown, retry to enter the command.
8) Send the process mode switching command to switch from the RS232C operation mode to the process mode.
KRSW0001: "ERR" is returned.
KKT10037: When "OK" is returned, the process mode becomes active. When "ERR", start over from KRSW0001.
9) Send each adjustment command.
RS-232C command list
3 23
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
[10] Initialization to factory settings
Caution: When the factory settings have been made, all user setting data, including the channel settings, are initialized.
(The adjustments done in the adjustment process mode are not initialized.) Keep this in mind when initializing these settings.
2 - If the situation 1 happens 5 times sequentially, the power is turned on (relay is turned ON).
However, the backlight is not turned on, and then the relay is turned OFF after 5 to 6 seconds. (The power LED turns from green to red.)
2. Countermeasures
When television is turned OFF by the lamp error detection mentioned above, it enters the adjustment process with the power LED red. Entering the
adjustment process turns OFF the error detection and turns ON TV. This enables the operation check to detect errors in the lamp or lamp circuit
Check whether L ERROR RESET on point 7, page 10/11 of the adjustment process is 1 or more. If it is 1 or more, it indicates the lamp error detec-
tion was executed. After confirming that the lamp or lamp circuit is normal, reset the lamp error counter pushing OK in the R/C. After resetting
counter the label ***OK*** appears on Screen.
3 24
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
[12] Public Mode (Hotel Mode)
1. How to Enter in the Public Mode (Hotel Mode).
Turn on the power and enter in the Adjustment Process mode as usual.
In the [INIT], Page 2/11 of Service, turns ON the Public Mode option.
Turn off TV by pressing Main Power switch.
While pressing VOL+ and INPUT keys at the same time, press Main Power switch for more than 2 seconds.
Then, when you are asked for the password, enter 027.
After this sequence the TV will turn on showing the Public Mode setting screen as follows:
Is possible to select each item of function by pressing cursor UP/DOWN keys on the remote control or CH( )( ) keys on the LCD TV. (Except
DTV)
The setting position of each item of functions is made by pressing cursor RIGHT/LEFT keys on the remote control or VOL (+) / (-) keys on the LCD
TV.
Select EXECUTE position after you set all function, and press cursor RIGHT/LEFT keys on the remote control or VOL (+) / (-) keys on the LCD TV for
confirmation.
3 25
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
11.RESET
Cancel all Public Mode settings. (It returns to the factory settings)
12.EXECUTE
Select this item, and press cursor RIGHT / LEFT keys on the remote control or VOL (+) / (-) keys on the LCD TV for confirmation the functions set-
tings.
3 26
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
LC32D44E-BK
Service
CHAPTER 4. TROUBLE SHOOTING TABLE Manual
NO
Is the wire harness in the unit properly connected? Reconnect and recheck the wire harness.
YES
NO
Are L7101-2, L7110, C7104-5, VA7103, D7101, etc. faulty? Check if
Are F7101 and F7103 normal?
the peripheral circuits are short-circuited.
YES
NO
Are T7101, D7104, TH7101, C7118, etc.faulty? Check if the periph-
Is F7102 normal?
eral circuits are short-circuited.
YES
NO
Is BU5V supplied from PIN(11) of connector CN7201 Check the peripheral circuits on the primary side of IC7101, T7101,
when the power switch is turned on? etc. and the secondary side of D7222, D7215, L7206, PC7104, etc.
YES
Is the PS_ON signal sent to PIN(10) of connector CN7201 NO
Check the peripheral circuits such as PS_ON circuits of Q7207,
when turning on the power switch and does RL7101 nor-
PC7103, RL7101, etc.
mally work?
YES
NO Does the PFC circuit normally work?
Is a DC voltage of approx. 400V applied to both ends of
(Check IC7102, L7103, L7104, D7106, D7108, TH7102, Q7104-5,
C7129?
Q7117, etc. and the peripheral circuits.)
YES
NO Check the primary side of T7102-3, Q7111-6, etc., the secondary side
Is 13V supplied from PIN(1-4) of connector CN7201 when
of D7203, etc., the peripheral circuits and the protection circuits of
the power switch is turned on?
D7205, D7208, PC7102, etc.
YES
NO
Check the secondary side of D7201, the protection circuits of D7206,
Is 60V supplied when the power switch is turned on?
D7207, D7209, PC7102, etc. and the peripheral circuits.
41
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
The backlight does not light
NO
Check each fluorescent lamp, and replace if defective.
Are all fluorescent lamps on?
(CN7503-12, etc.)
NO
NO
Check if the peripheral circuits are short-circuited or parts are faulty.
Is F7501 normal?
(Q7501, Q7503, etc.)
YES
NO
Refer to "No power supply (Front LED does not light up)" and "No
Is 60V applied to both ends of C7501?
power-up even if turned on (Front LED light up)".
YES
NO
Is a voltage of 13V applied to PIN(20) of IC7501? Check the 13V line and the peripheral circuits.
YES
NO Check the STB signal line on the MAIN_UNIT side and the peripheral
Is the STB_ON/OFF signal supplied from PIN(2) of
circuits.
CN7502?
(P2303/CN7502, etc.)
YES
Is each control signal of connector CN7502 normally func-
NO Check each control circuit.
tion?
PIN(3) OFL (PWM light control signal input) OFL (PWM light control signal input)/H: Lamp ON, L: Lamp OFF
PIN(5) ERR (Error output) ERR (Error output)/H: Normal, L: Error
REG2 (Light control method identification)/H: External PWM input, L:
PIN(7) REG2 (Light control method identification)
Analog voltage input
ADIM (Tube current setting)/H: Tube current 12mA, L: Tube current
PIN(9) ADIM (Tube current setting)
8.5mA
YES
NO
Is [0] displayed as the number of [LAMP_ERROR] in the Reset the number of [LAMP_ERROR] to the default value in the pro-
process mode? cess mode.
YES
NO
Is the drive output signal sent from PIN(16) and (15) of
Check IC7501and the peripheral circuits.
IC7501?
YES
NO
Does the drive output circuit normally work? Are Q7509-10, Q7501-4, etc. faulty? Check the peripheral circuits.
YES
NO
Does the secondary side of T7501-5 normally work? Is T7501-5, etc. faulty? Check the peripheral circuits.
YES
Check if the feedback circuit is normal.
(D7501-5, D7507-11, D7513-17, etc.)
42
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
The sound is not emitted from the speaker though the picture has come out.
NO
Is the audio signal output of pins (28/L) and (27/R) of
Check IC3001 and its peripheral circuits.
IC3001 (MAIN_MICON) normal?
YES
NO
Is audio signal input to pin(5/L), pin(9/R) of IC2701(AMP)? Check the line between IC3001 and IC2701.
YES
NO
Is MUTE circuit [MUTE_SP_LINE, RESET_N_LINE] nor- Check the MUTE_SP_LINE and RESET_N_LINE.
mal? (Q2701, etc.)
YES
NO
Is the audio signal output of pins (3, 4) (L-ch) and (2, 1)
Check IC2701 and its peripheral circuits.
(R-ch) of P2701(AOUDIO-CONNECTOR) normal?
YES
Check Speaker (right and left) and wire harness.
Does not the sound go out though the picture has come out when UHF/VHF is received?
NO
Check the tuner and its peripheral circuits.
Is the SIF signal output from pin (4) of TUNER (TU201)?
Replace as required.
YES
NO
Is the SIF signal sent to pins (31) of IC3001
Check the line between TU201 and IC3001.
(MAIN_MICON)?
YES
Refer to No sound output in all modes.
43
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
No sound (during the reception of TV(DIGITAL) broadcasting)
Does not the sound go out though the picture has come out when DTV is received?
YES
NO
Is the audio signal input to PIN(6,5)/ LETFT_M/P, (2,3)/
Check the line between IC4001 and IC4005.
RIGH_M/P of IC4005(OP-AMP)?
YES
NO
Is the audio signal sent from PIN(7)/ AIN1L, (1)/AIN1R of
Check the line between IC4005 and IC3001.
IC4005 to PIN(10), PIN(9) of IC3001 (MAIN_MICON)?
YES
Refer to No sound output in all modes.
Does not the sound of the audio signal input to EXT1(SCART1) go out?
Does not the sound of the audio signal input to EXT2(SCART2) go out?
EXT1 NO
Check the setting of an external input device that connects of
Is the audio signal properly sent to pins (6) (AIN3_L) and
SC1102.
(2) (AIN3_R) of SCART1(SC1102)?
EXT2 NO
Check the setting of an external input device that connects of
Is the audio signal properly sent to pins (6) (AIN2_L) and
SC1101.
(2) (AIN2_R) of SCART2(SC1101)?
YES
EXT1 NO
Is the audio signal properly sent to pins (14) (AIN3_L) and Check the line between SC1102 and IC3001.
(13) (AIN3_R) of IC3001(MAIN_MICON)?
EXT2 NO
Is the audio signal properly sent to pins (12) (AIN2_L) and Check the line between SC1101 and IC3001.
(11) (AIN2_R) of IC3001(MAIN_MICON)?
YES
Refer to No sound output in all modes.
44
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Does not the sound of the audio signal input to EXT3 go out?
MINI AV UNIT:
Is audio signal output from pin(5/IN3L), (4/IN3R) of input NO
Check connection of between from J1002 to SC1001 and the exter-
terminal J1002 to pin(8), (6) of connector SC1001?
nal input device.
YES
Is audio signal input to pin(1/IN3L), (6/IN3R) of IC1301 NO
(AUDIO_SELECTOR)? Check the line between P1001 and IC1301.
YES
NO
Is the audio signal sent to pin (15/AIN4L), (11/AIN4R) of
Check IC1301 and its peripheral circuits.
IC1301?
YES
Is audio signal input from pin (15/AIN4L), (11/AIN4R) of IC1301 to pin (16, 15) of IC3001 (MAIN_MICON)?
YES NO
Refer to No sound output in all modes Check the line between IC1301 and IC3001.
Does not the sound of the audio signal input to EXT4 go Does not the sound of the audio signal input to EXT6(Analog) go
out? out?
Is audio signal sent from pin(2/L) and (3/R) of input termi- YES
Is audio signal sent from pin(2/L) and (3/R) of input terminal J1302
nal J1301 to pin(5) and (8) of IC1301
to pin(3) and (7) of IC1301(AUDIO_SELECTOR)?
(AUDIO_SELECTOR)?
NO NO
Check the connection between J1301 and the peripheral Check the connection between J1302 and the peripheral circuit, the
circuit, the external input devices. external input devices.
NO
Is the audio signal sent to pin (15/AIN4L), (11/AIN4R) of
Check IC1301 and its peripheral circuits.
IC1301?
45
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
YES
Is audio signal input from pin (15/AIN4L), (11/AIN4R) of IC1301 to pin (16, 15) of IC3001 (MAIN_MICON)?
YES NO
Refer to No sound output in all modes Check the line between IC1301 and IC3001.
Does not the sound of the audio signal input to EXT5 go out?
YES
NO
Is the audio signal sent to pin (15/AIN4L), (11/AIN4R) of
Check IC1301 and its peripheral circuits.
IC1301?
YES
Is audio signal input from pin (15/AIN4L), (11/AIN4R) of IC1301 to pin (16, 15) of IC3001 (MAIN_MICON)?
YES NO
Refer to No sound output in all modes Check the line between IC1301 and IC3001.
Does not the sound of the audio signal input to EXT6/7(HDMI) go out?
NO
Refer to Does not the picture of the HDMI signal input to EXT6/7 go
Is picture of the signal input from EXT6/7 displayed?
out?.
YES
Is the HDMI_SCK/ WS/ SD0 audio signal output from NO
Check the line between IC1951 and IC3001, and their peripheral cir-
pin(86), (85), (84) of IC1951 (HDMI RECEIVER) to pin(39),
cuits.
(40), (38) of IC3001 (MAIN_MICON)?
YES
Refer to No sound output in all modes.
46
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
YES
Is audio signal sent to pins (3/L-ch) and (1/R-ch) of
Check the connection to SCART1 and external devices.
SCART1(SC1102)?
NO
YES
Check the peripheral circuits of IC2302 and S-MUTE_LINE.
Is S-MUTE-LINE [pin(62) of IC2302(SUB_MICON)] at H?
(Q1101, etc.)
NO
YES
Is audio signal sent to pins (24/L-ch) and (23/R-ch) of Check the line between SC1102 and IC3001.
IC3001(MAIN_MICON)? (Q1106, Q1105, etc.)
NO
Check IC3001 and its peripheral circuits.
YES
Is audio signal sent to pins (3/L-ch) and (1/R-ch) of
Check the connection to SCART2 and external devices.
SCART2(SC1101)?
NO
YES
Check the peripheral circuits of IC2302 and S2-MUTE_LINE.
Is S2-MUTE-LINE [pin(63) of IC2302(SUB_MICON)] at H?
(Q1102, etc.)
NO
YES
Is audio signal sent to pins (22/L-ch) and (21/R-ch) of Check the line between SC1101 and IC3001.
IC3001(MAIN_MICON)? (Q1108, Q1107, etc.)
NO
Check IC3001 and its peripheral circuits.
47
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
YES
Is audio signal output to pin(2/L-ch), (4/R-ch) of audio out-
Check the connection to J1304 and external devices.
put terminal J1304?
NO
YES
Check the peripheral circuits of IC2302 and S-MUTE_LINE.
Is S-MUTE-LINE [pin(62) of IC2302(SUB_MICON)] at H?
(Q1303, etc.)
NO
YES
Is audio signal sent to pins (22/L-ch) and (21/R-ch) of Check the line between J1304 and IC3001.
IC3001(MAIN_MICON)? (Q1302, Q1301, etc.)
NO
Check IC3001 and its peripheral circuits.
YES
YES
Is the audio signal output to pin(2/L-ch) pin(3/R-ch) of
Check HEAD-PHONE (J1003) or peripheral circuits.
headphone terminal J1003?
NO
YES
Is the audio signal input into pin (3) and (1) of connector Check the line between P1001 and J1003.
SC1001 from pin(3/L-ch),(1/R-ch) of connector P1001? (SC1001/P1001, etc.)
NO
YES
Is HP-MUTE-LINE [pin(40) of IC2302(SUB_MICON)] at Check the peripheral circuits of IC2302 and HP-MUTE_LINE.
H? (Q1001, etc.)
NO
YES
Is audio signal sent to pins (26/L-ch) and (25/R-ch) of Check the line between P1001 and IC3001.
IC3001(MAIN_MICON)? (IC1102, etc.)
NO
Check IC3001 and its peripheral circuits.
48
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
YES
Is the LVDS signal input to IC8103 (LCD_CONTROL)? NO
A0+/-(165/164), A1+/-(167/166), A2+/-(169/168), A3+/- Check the line between IC3001 and IC8103.
(189/188), A4+/-(191/190), ACK+/-(187/186)
YES
NO Check the control signal R/L_LINE, U/D_OUT_LINE,
Is the control signal of LCD controller normal? FRAME_LINE, BANK_SEL_LINE, TEMP1/2/3_LINE,
QS_EN_LINE, etc.
YES
NO
Is VCC_3.3V, VCC_2.5V or VCC_1.5V supplied to Check if IC8402(MULTI_CHANNEL_SYSTEM_POWER_SUPPLY)
IC8103? and the peripheral power supply circuit are normal.
YES
Are the video signals BR/BG/BB (0_P/M-3_P/M), FR/ NO
FG/FB (0_P/M-3_M/P) and the CLK signals (BCLK_P/ Check IC8103 and its peripheral circuits.
M, FCLK_P/M) output from IC8103?
YES
Are BR/BG/BB (0_P/M-3_P/M), BCLK (P/M) input to NO
connector SC8201 and FR/FG/FB (0_P/M-3_P/M), Check the line between IC8103 and SC8201/SC8202.
FCLK (P/M) input to connector SC8202?
YES
Are the gradation signals (VH/VL_247, 191, 159, 63, NO Check IC8201 and that the communication between its peripheral
31, 0) normally sent from IC8201 (GLAY_LEVEL circuits and IC8103 is normal. (Each line of DAC_CLK/DATA/
_GENERATION) to SC8201/SC8202? LATCH)
YES
Check the connectors SC8201/SC8202 and LCD panel.
NO
Is the video signal(VIN1) output from pin (6) of TUNER Check whether I2C is normally accessed between named TU201
(TU201)? and IC3001(MAIN_MICON).
YES
NO
Is the video signal(VIN1) sent to pins (191) of IC3001
Check the line between TU201 and IC3001.
(MAIN_MICON)?
YES
Refer to The picture doesn't appear in all modes.
49
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
No picture on the display (3)
YES
NO
Is IF signal output from pin (16),(17) of TUNER(TU201)
to pin(10),(11) of IC207(COFDM)?
YES
NO
Does X201(27MHz) oscillate? Check X201 and its peripheral circuits.
YES
NO
Is the MPEG data (FESCL, FESDA, FEVALID, FES- Check if the line between IC207 and IC4001 and the control signals
TROUT) output from IC207 to IC4001? FERROR_LINE and FERESET_LEINE are normal. (IC4402, etc.)
YES
NO
Are the video signals (DTV_R/G/B, DTV_CVBS) output Check if IC4001, IC4201(SDRAM), IC4251(FLASH_MEMORY) and
from PIN(15,16,17), PIN(18) of IC4001? IC4202(B+2.5V_REG) are normal.
YES
Are the video signals (DTV_R/G/B, DTV_CVBS) input NO
Check the line between IC4001 and IC3001.
to PIN(181,180,179), PIN(184) of IC3001
(IC1401, IC1001, Q1031, etc.)
(MAIN_MICON)?
YES
Refer to The picture doesn't appear in all modes.
4 10
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Does not the picture of the CVBS signal input to EXT1 go out?
Does not the picture of the CVBS signal input to EXT2 go out?
<EXT1> NO Check the setting of an external input device that connects of SC1102.
Is CVBS signal sent to pin (20) of SCART1 (SC1102)?
<EXT2> NO Check the setting of an external input device that connects of SC1101.
Is CVBS signal sent to pin (20) of SCART2 (SC1101)?
YES
NO Check the line between SC1102 and IC1502
<EXT1>
Is CVBS signal sent to pin (6) of IC1502(SW.)?
NO Check the line between SC1101 and IC1502.
<EXT2>
Is CVBS signal sent to pin (4) of IC1502(SW.)?
YES
Is CVBS signal output to pin(190) of NO Check the line between IC1502 and IC3001.
IC3001(MAIN_MICON) from pin(2) of IC1502? (SCART12_LINE, etc.)
YES
Does not the picture of the R/G/B video signal input to EXT1 go out?
Does not the picture of the R/G/B video signal input to EXT2 go out?
<EXT1> NO
Is RGB1 signal sent to pins (15)/R1, (11)/G1 and (7)/B1 Check the setting of an external input device that connects of SC1102.
of SCART1(SC1102)?
<EXT2> NO
Is RGB2 signal sent to pins (15)/R2, (11)/G2 and (7)/B2 Check the setting of an external input device that connects of SC1101.
of SCART2(SC1101)?
YES
<EXT1> NO
Is RGB1 signal sent to pins (187)/R1, (175)/G1 and Check the line between SC1102 and IC3001.
(182)/B1 of IC3001(MAIN_MICON)?
<EXT2> NO
Is RGB2 signal sent to pins (178)/R2, (177)/G2 and Check the line between SC1101 and IC3001.
(176)/B2 of IC3001(MAIN_MICON)?
YES
Refer to The picture doesnt appear in all modes.
4 11
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Does not the picture of the Y/C video signal input to EXT1 go out?
Does not the picture of the Y/C video signal input to EXT2 go out?
<EXT1> NO Check the setting of an external input device that connects of SC1102.
Is Y/C video signal sent to pins (20)/Y and (15)/C of
SCART1 (SC1102)?
<EXT2> NO Check the setting of an external input device that connects of SC1101.
Is Y/C video signal sent to pins (20)/Y and (15)/C of
SCART2 (SC1101)?
YES
<EXT1> NO Check the line between SC1102 and IC3001.
Is Y/C signal sent to pins (190)/Y, (187)/C of .(IC502, SCART12_LINE, etc.)
IC3001(MAIN_MICON)?
<EXT2> NO Check the line between SC1101 and IC3001
Is Y/C signal sent to pins (190)/Y, (178)/C of .(IC502, SCART12_LINE, etc.)
IC3001(MAIN_MICON)?
YES
Refer to The picture doesnt appear in all modes.
<When EXT3 is used for external input> No picture on the display (7)
Does not the picture of the composite video signal input to EXT3 go out?
Is CVBS signal output from pin(6) in input terminal NO Check the line between J1002 and SC1001.
J1002 to pin(10) of connector SC1001?
YES
Is the CVBS signal input from pin(10) of connector NO Check the line between P1001 and IC1001.
P1001 to pin(1) of IC1001(VIDEO SELECTOR)? (Connector SC1001/P1001, etc.)
YES
Is CVBS signal output to pin(184) of NO Check the line between IC1001 and IC3001.
IC3001(MAIN_MICON) from pin(7) of IC1001? (SV1JSW_LINE, EXT_DTV_LINE, etc.)
YES
Refer to (The picture doesn't appear in all modes.)
4 12
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
<When EXT3 is used for external input> No picture on the display (8)
Does not the picture of the Y/C video signal input to EXT3 go out?
Is Y/C signal input into pin(14), (12) of connector NO Check the line between J1001 and SC1001.
SC1001 from pin(3)/Y, (4)/C of J1001?
YES
Is Y/C signal output from pin(14)/Y,(12)/C of connector NO Check the connector SC1001/P1001.
P1001 ?
YES
Is the Y/C video signal detection function SV1JSW sig- NO Check J1001 or peripheral circuits.
nal from pin (6) of the input terminal J1001 normal?
YES
Is the SV1JSW signal input to pin(2) of IC1001 NO Check the between SV1JSW_LINE J1001 and IC1001/IC2302. (Con-
(VIDEO_SELECTOR) and pin(27) of IC2302 nector SC1001/P1001, etc.)
(SUB_MICON)?
YES
Is Y/C signal sent to pins (184), (183) of NO Check the line between P1001 and IC3001.
IC3001(MAIN_MICON)? (IC1001, EXT_DTV_LINE etc.)
YES
Refer to The picture doesn't appear in all modes.
<When EXT4 is used for external input> No picture on the display (9)
Does not the picture of the DVI(ANALOG) video signal input to EXT4(15pin-D-SUB terminal) go out?
YES
Are the video signal and the synchronized signal input NO Check the connection and setup with the external DVI devices.
from pin(1, 2, 3)/(R, G, B), (13 and 14)/(V, H) of input
terminal D-SUB (SC1201)?
YES
Is EDID data pin (6)/SCL, pin(5)/SDA of IC1201 NO Is access possible in the re-writing or exchange of EDID data of
(EEPROM) accessed, and is it read from pin (15),(12) IC1201?
of a DVI terminal(SC1201)?
NO
YES Check the circumference circuit of SC1201, IC1201.
Are the video signal and the synchronized signal input NO Check the line between SC1201 and IC3001.
from pin(174, 173, 172)/(R, G, B), pin(171, 47)/(H, V) of (IC1941,etc)
IC3001(MAIN_MICON)?
YES
Refer to The picture doesn't appear in all modes.
4 13
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
<When EXT5 is used for external input> No picture on the display (10)
Does not the picture of the component video signal input to EXT5 go out?
Is COMPONENT video signal input into pin(3)/Y, (5)/Pb, NO Check the connection of J1401 and the external input device.
(7)/Pr of the input terminal J1401?
YES
Is COMPONENT video signal input into pin(1)/Y, (6)/Pb, NO Check the line between J1401 and IC1401.
(9)/Pr of IC1401(VIDEO_BUFFER)?
YES
Is COMPONENT signal output into pin(180), (179), NO Check the line between IC1401 and IC3001.
(181) of IC3001(MAIN_MICON) from pin(20)/Y, (18)/PB,
(16)/PR of IC1401?
YES
Refer to The picture doesn't appear in all modes
4 14
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
<When EXT6/7 is used for external input> No picture on the display (11)
Does not the picture of the HDMI signal input to EXT6/7 go out?
EXT6 EXT6
Is the HDMI detection function output from pin (19) of Check between SC1901and IC3001(MAIN_MICON) of pin(205).
the HDMI terminal (SC1901) normal? NO (Q1905, etc.)
EXT7 EXT7
Is the HDMI detection function output from pin (19) of Check between SC1921 and IC3001(MAIN_MICON) of pin(203).
the HDMI terminal (SC1921) normal? (Q1925, etc.)
Check the connection and setup with the external HDMI devices.
YES
EXT6 NO
Is access possible in the re-writing or exchange of EDID data of
Is EDID data pin (6)/SCL, pin(5)/SDA of IC1902?
IC1902(EEPROM) accessed, and is it read from pin
(15),(16) of a HDMI terminal(SC1901)?
NO
Check the circumference circuit of SC1901, IC1902 and
IC1951(HDMI_RECEIVER).
EXT7
Is EDID data pin (6)/SCL, pin(5)/SDA of NO
Is access possible in the re-writing or exchange of EDID data of
IC1922(EEPROM) accessed, and is it read from pin
IC1922?
(15),(16) of a HDMI terminal(SC1921)?
NO
Check the circumference circuit of SC1921, IC1922 and
IC1951(HDMI_RECEIVER).
YES
EXT6
Is TMDS signal input into pin(59,58)/TMDS2_CLKP/N, NO
(63,62)/TMDS2_D0P/N, (67,66)/TMDS2_D1P/N, Check the line between SC1901 and IC1951.
(71,70)/TMDS2_D2P/N of IC1951 from SC1901?
EXT7
Is TMDS signal input into pin(40,39)/TMDS1_CLKP/N, NO
(44,43)/TMDS1_D0P/N, (48,47)/TMDS1_D1P/N, Check the line between SC1921 and IC1951.
(52,51)/TMDS1_D2P/N of IC1951 from SC1921?
YES
Is each signal output from DINR[0:7], DING[0:7], NO
Is the control signal of IC1951 and IC3001 (MAIN_MICON) normal?
DINB[0:7], pin(2,3)/HDMI_H/V, (1)/DINEN, (121)/
(HDMI_RST, IC1941, etc.)
DINCK, of IC1951?
YES
Is each signal of DINR[0:7], DING[0:7], DINB[0:7], pin(171,47)/HDMI_H/V, (48)/DINEN, (49)/DINCK of IC3001(MAIN_MICON) input?
YES NO
Check the line between IC1951 and IC3001.
Refer to The picture doesn't appear in all modes.
(IC1941, etc.)
4 15
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Checklist:
1) Is the Signal Type (item) in MENU-Option-Input Select equal to Signal Type of an external device?... Set it to CVBS, Y/C or RGB.
2) Is ANT-CABLE disconnected or connected improperly? ... Connect it correctly as per the operation manual.
3) The picture is sent to the monitor in a CVBS signal if the source during display is TV, CVBS or Y/C of EXT1-3.
When sent by component, etc., that signal is not sent to the monitor.
4) When the monitor picture is not sent and is not displayed on the monitor, refer to No picture for each terminal.
5) The video output from EXT1 is not the monitor output (output of the picture now watching).
The picture of the last selected TV channel is always sent to EXT1. (Specification)
Is CVBS signal output into pin(19) of SC1102(SCART1) YES Check the setting of an external input device that connects of SC1102.
from pin(2) of IC1102(SW)?
NO
Is CVBS signal output from PIN(195) of YES Check the line between IC1102 and SC1102.
IC3001(MAIN_MICON) to PIN(6) of IC1102?
NO
Is video signal (CVBS) sent to pin (195) of IC3001? YES Check power supply of IC3001 and peripheral circuits.
NO
Is VIN1 signal output from pin(6) of TUNRE(TU201)? YES Check the line between TU201 and IC3001.
NO
Check whether I2C is normally accessed between
TU201 and IC3001.
4 16
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Checklist:
1) Is the Signal Type (item) in MENU-Option-Input Select equal to Signal Type of an external device? ... Set it to CVBS, Y/C or RGB.
2) Is ANT-CABLE disconnected or connected improperly? ... Connect it correctly as per the operation manual.
3) The picture is sent to the monitor in a CVBS signal if the source during display is TV, CVBS or Y/C of EXT1-3.
When sent by component, etc., that signal is not sent to the monitor.
4) When the monitor picture is not sent and is not displayed on the monitor, refer to No picture for each terminal.
5) The video output from EXT1 is not the monitor output (output of the picture now watching).
The picture of the last selected TV channel is always sent to EXT1. (Specification)
Is DTV_CVBS signal output from pin(2) of IC1102(SW) YES Check the setting of an external input device that connects of SC1102.
to pin(19) of SC1102(SCART1)?
NO
Is DTV_CVBS signal output from PIN(195) of YES Check the line between IC1102 and SC1102.
IC3001(MAIN_MICON) to PIN(6) of IC1102?
NO
Is video signal (DTV_CVBS) sent to pin (184) of YES Check power supply of IC3001 and peripheral circuits.
IC3001?
NO
Is DTV_CVBS signal output from PIN(18) of YES Check the line between IC4001 and IC3001.
IC4001(SET-TOP_BOX_DECODER)? (IC1001, EXT_DTV_LINE, etc.)
NO
Check the IC4001 and its peripheral circuits.
4 17
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Checklist:
1) Is the Signal Type (item) in MENU-Option-Input Select equal to Signal Type of an external device? ... Set it to CVBS, Y/C or RGB.
2) The picture is sent to the monitor in a CVBS signal if the source during display is TV, CVBS or Y/C of EXT1-3.
3) When the monitor picture is not sent and is not displayed on the monitor, refer to No picture for each terminal.
When sent by component, etc., that signal is not sent to the monitor.
4) The video output from EXT1 is not the monitor output (output of the picture now watching).
The picture of the last selected TV channel is always sent to EXT1. (Specification)
Is CVBS signal output into pin(19) of SC1101(SCART2) YES Check the setting of an external input device that connects of SC1101.
from pin(2) of IC1101(SW)?
NO
Is CVBS signal output into pin(194) of YES Check the line between IC1101 and SC1101.
IC3001(MAIN_MICON) from pin(6) of IC1101?
NO
Is video signal (VIN2) from EXT1 sent to pin (190) of YES Check power supply of IC3001 and peripheral circuits.
IC3001 (MAIN_MICON)?
NO
Is CVBS signal sent to pin (20) of SCART1(SC1102)? YES Check the line between SC1102 and IC3001.
(IC1502, SCART12_LINE, etc.)
NO
Check the setting of an external input device that con-
nects of SC1102.
4 18
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Checklist:
1) Is the Signal Type (item) in MENU-Option-Input Select equal to Signal Type of an external device? ... Set it to CVBS, Y/C or RGB.
2) The picture is sent to the monitor in a CVBS signal if the source during display is TV, CVBS or Y/C of EXT1-3.
When sent by component, etc., that signal is not sent to the monitor.
3) When the monitor picture is not sent and is not displayed on the monitor, refer to No picture for each terminal.
4) The video output from EXT1 is not the monitor output (output of the picture now watching).
The picture of the last selected TV channel is always sent to EXT1. (Specification)
Is CVBS signal output into pin(19) of SC1101(SCART2) YES Check the setting of an external input device that connects of SC1101.
from pin(2) of IC1101(SW)?
NO
Is CVBS signal output into pin(194) of YES Check the line between IC1101 and SC1101.
IC3001(MAIN_MICON) from pin(6) of IC1101?
NO
Is CVBS signal output into pin(194) of IC3001 from YES Check power supply of IC3001 (MAIN_MICON) and peripheral circuits.
pin(6) of IC1101(VIDEO_SELECTOR)?
NO
Is CVBS signal output into PIN(1) of IC1001 from YES Check IC1001 and its peripheral circuits.
PIN(10) of connector P1001? (SV1JSW_LINE, EXTDTV_LINE)
NO
Check the setting of an external input device that con-
nects of SC1102.
MINI_AV_UNIT: NO
Is the video signal output into PIN(10) of connector YES Check the connector SC1001/P1001.
SC1001 from PIN(6) of input terminal J1002?
NO
Check the setting of an external input device that con-
nects of J1002.
4 19
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
CHAPTER 5. MAJOR IC INFORMATIONS Service
LC32D44E-BK
Manual
51
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Pin No. Pin Name I/O Pin Function
26 CS1 I Chip select MSB
Power supply
19, 24, 31, 38, 45, 51, 55, 62 VDD_1V0 --- Digital core supply (1.0 V)
22, 28, 34, 41, 50, 56, 63 VDD_3V3 --- Digital I/O supply (3.3 V)
2. IC1301 (VHINJM2750M-1Y)
The NJM2750 is a 4-input/1-output stereo audio selector. It contains a switch operational amplifier and shows lower noise, lower distortion and higher
channel separation than an ordinary multiplexer or analog switch.
Description:
Operating voltage (4.7 - 13V)
4-input/1-output audio selector
Stereo 2-channel
Low output noise (-110dBV typ.)
Low distortion (0.005% typ.)
3. IC1401 (VHISM5309AV-1Y)
The SM5309A is a 3ch video buffer with a built-in 5th-order low pass filter. The cutoff frequency of the low pass filter can be adjusted between 4MHz
and 40MHz in 256 steps. The low pass filter supports analog inputs/outputs of video signal device of 480i to 1080i format. When it is used as an input
system, it functions as an antialiasing filter of the rear-stage ADC system. If used as an output system, aliasing noise from the video DAC or exoge-
nous noise is eliminated, and the terminating resistance of up to 300 can be driven. The cutoff frequency or signal input method can be controlled by
I2C-BUS.
Description:
Supply voltage: Analog: 4.75 - 5.25V
Digital: 3.0 - 5.5V
Low pass filter function where cutoff frequency can be adjusted in 256 steps
Cutoff frequency range: 4MHz - 40MHz (RISET = 1.8k)
Filter bypath mode function supporting the resolution of SXGA
Switchable to the half fc mode suitable for the component signal (CH-2, CH-3)
2-input multiplexer function (switchable by the I2C-BUS or MUXSEL terminal)
For the video input terminal, the sync-tip clamp/bias/direct input can be selected per channel.
Possible to drive the terminating resistance of up to 300
Output gain: 0dB
Power down function
Consumption current at power down: 1mA or less
Control by I2C-BUS interface
Transfer rate: First mode (400kbit/s) supported
52
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Pin No. Pin Name I/O Pin Function
5 NC --- No connection.
6 IN2A I Video signal input terminal (CH-2, A input)
7 IN2B I Video signal input terminal (CH-2, B input)
8 VCC --- Analog power supply.
9 IN3A I Video signal input terminal (CH-3, A input)
10 IN3B I Video signal input terminal (CH-3, B input)
11 MUXSEL I Input multiplexer select terminal.
12 SCL I I2C clock signal input.
13 SDA I/O I2C data signal in-output.
14 VDD --- Digital power supply.
15 GND --- Ground.
16 OUT3 O Video signal output terminal (CH-3)
17 VCC --- Analog power supply.
18 OUT2 O Video signal output terminal (CH-2)
19 GND --- Ground.
20 OUT1 O Video signal output terminal (CH-1)
21 VCC --- Analog power supply.
22 REF2 O Internal reference voltage 2.
23 REF1 O Internal reference voltage 1.
24 ADS I I2C slave address setting terminal (3 states).
4. IC1501 (VHIISL83220-1Y)
+/-15kV ESD Protected, +3V to +5.5V, 1Microamp, 250kbps, RS-232 Transmitters/Receivers.
The ISL83220E is a 3.0V to 5.5V powered RS-232 transmitter/ receiver which meets ElA/TIA-232 and V.28/ V.24 specifications, even at VCC = 3.0V.
Additionally, it provides 15kV ESD protection (IEC 1000-4-2 Air Gap and Human Body Model) on transmitter outputs and receiver inputs (RS-232
pins). Targeted applications are PDAs, Palmtops, and notebook and laptop computers where the low operational, and even lower standby, power
consumption is critical. Efficient on-chip charge pumps, coupled with a manual power down function, reduce the standby supply current to a 1 A
trickle. Small footprint packaging, and the use of small, low value capacitors ensure board space savings as well. Data rates greater than 250kbps are
guaranteed at worst case load conditions. This family is fully compatible with 3.3V only systems, mixed 3.3V and 5.0V systems, and 5.0V only sys-
tems.
53
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
5. IC1702/1735/1745 (VHILV5805M+-1Y)
Step-down DC-DC converter
This is a 1ch step-down switching regulator. It incorporates 0.2FET on the upper side and realizes high-efficiency operation for large output current.
Since the current mode control method is adopted, good load current response and easy phase compensation are available.
The standby mode can be entered using the ON/OFF terminal. The load device is protected by the pulse-by-pulse or current protection and overheat
protection function. Soft start becomes possible by applying capacitance to the soft start terminal.
6. IC1951 (VHiSii9025+-1Q)
The Sii9025 is a compliant with the latest HDMI 1.2 (High Definition Multimedia Interface) specification.
Backward compatibility with DVI 1.0 allows HDMI systems to connect to existing DVI 1.0 hosts.
The SiI9025 is capable of receiving and outputting two channel digital audio at up to 192 kHz- an excellent solution for Digital TVs.
An S/PDIF port supports up to 192 kHz audio.
The SiI9025 also comes pre-programmed with HDCP keys, greatly simplifying the manufacturing process, while providing the highest level of HDCP
key security.
Description:
Dual-Input HDMI 1.2, HDCP 1.1 and DVI 1.0 compliant receiver.
Integrated TMDSR core.
Digital video interface supports video processors:
24-bit RGB/YCbCr 4:4:4
16/20/24-bit YCbCr 4:2:2
8/10/12-bit YCbCr 4:2:2 (ITU BT.656)
12-bit DMO (Digital Multimedia Output) RGB/YCbCr 4:4:4 (clocked with rising & falling edges)
Color Space Conversion for both RGB-to-YCbCr and YCbCr-to-RGB (both 601 and 709)
Auto video mode configuration simplifies system firmware design.
Digital audio interface supports high-end audio systems:
One programmable I2S output for connection to low-cost DACs at 32-192kHz.
S/PDIF output supports PCM, Dolby Digital, DTS digital audio transmission (32-192kHz Fs) using IEC60958 and IEC61937.
Auto audio error detection with programmable soft mute.
Integrated HDCP decryption engine for receiving protected audio and video content.
54
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
HDCP Built in Self Test (BIST) lowers cost to test HDCP operation.
Pre-programmed HDCP keys provide highest level of key security, simplifies manufacturing.
55
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Pin No. Pin Name I/O Pin Function
54 TMDSPGND --- TMDS PLL GND.
94 AUDPVCC18 --- ACR PLL VCC.
95 AUDPGND --- ACR PLL GND.
98 XTALVCC --- ACR PLL Crystal Input VCC.
99 REGVCC --- ACR PLL Regulator VCC.
7. IC2302 (RH-IXC009WJZZQ)
The RH-IXC009WJZZQ is a high-speed and high-performance 8-bit single-chip microcomputer with a built-in 61440-byte flash memory.
In this equipment, the R/C LED on the AVC side and system on the display side are controlled.
56
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Pin No. Pin Name I/O Pin Function
22 AIN2 I N.C.
23 AIN3 I N.C.
24 AC_DET I Power supply detection.
25 ANT_ERR I ANT5V short detection.
26 BL_ERR I Backlight detection.
27 SV1JSW I S-terminal detection.
28 QS_EN O Panel controller QS.
29 FRAME O 50/60Hz select.
30 T1 I Panel controller TEMP.
31 T2 I Panel controller TEMP.
32 T3 I Panel controller TEMP.
33 BANK_SEL O Panel controller
34 R/L O Panel controller. Flip horizontal.
35 U/D O Panel controller. Flip vertical.
36 EXT_DTV O DTV_etc. select (H,V,Audio)
37 HDMI_PC O HDMI-PC select (H,V,Audio)
38 SCART12 O SCARTselect.
39 PE O Panel enable.
40 HP_MUTE O Mute. Headphono.
41 ANT+5V_SW O ANT+5V control
42 DTN_BUS_SEL O D-TUNER I2C select
43 DTM_RST O DTV PWB reset
44 TCON_WP O Counter adjustment write-protect
45 LVDS_EN O N.C
46 CONT_DET --- N.C
47 PS_ON O Power_on.
48 PCON1 O DC-DC_on.
49 TEST O N.C
50 LCD_POW O N.C
51 12V_DET O LCD_12V detection.
52 SCL I I2C Slave clock
53 SDA I/O I2C Slave data
54 I-REQ O Sub-microprocessor interrupt
55 SCL_F I N.C. (Pull-up)
56 SDA_F I/O N.C. (Pull-up)
57 LEDPOW_R O Power R_LED ON.
58 LEDPOW_G O Power G_LED ON.
59 LEDSLP O N.C.
60 LEDOPC O N.C.
61 MUTE_SP O Mute.
62 S_MUTE O Mute.
63 S2_MUTE O Mute SCART2.
64 IREM_SW O N.C.
57
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
8. IC2701 (VHiYDA147SZ-1Y)
High-efficiency digital audio power amplifier IC with maximum power output of 20W (Vddp=14V, RL=4) x 2ch.
It incorporates the DRC (Dynamic range compression) function. Since the volume is increased at low volume level and is decreased at high volume
level, it is possible to prevent sudden volume change. It is also provided with the power limiter which can set the output limit.
58
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
9. IC3001 (RH-IXC354WJZZQ)
The VCT-Pro front-end video processing unit offers 16 analog video inputs (CVBS/Y/C, RGB/Y Cr Cb) as well as digital interfaces for SDTV and DTV.
Latest 3D+ comb filter generation provides highest performance for PAL/NTSC signals.
A VBI slicer, supporting up to 2000 pages of Teletext completes the analog video front end. 3D-motion-adaptive de-interlacing, temporal noise reduc-
tion and film mode detection are based on a unified memory technology.
Description:
Stereo Decoder Audio Processing.
Video Front-end 3D Comb filter, PC Connectivity.
Motion Adaptive De-interlacing.
Scaling, Display Processing and FPD Control.
Unified Memory for Audio, Video and Text.
Controlling, OSD and Text.
59
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Pin No. Pin Name I/O Pin Function
51 DRI6 I Digital Video Red 6 Input.
52 DRI5 I Digital Video Red 5 Input.
53 DRI4 I Digital Video Red 4 Input.
54 DRI3 I Digital Video Red 3 Input.
55 DRI2 I Digital Video Red 2 Input.
56 DRI1 I Digital Video Red 1 Input.
57 DRI0 I Digital Video Red 0 Input (LSB).
58 DGI7 I Digital Video Green 7 Input.
59 DGI6 I Digital Video Green 6 Input.
60 DGI5 I Digital Video Green 5 Input.
61 DGI4 I Digital Video Green 4 Input.
62 DGI3 I Digital Video Green 3 Input.
63 DGI2 I Digital Video Green 2 Input.
64 DGI1 I Digital Video Green 1 Input.
65 DGI0 I Digital Video Green 0 Input (LSB).
66 DBI7 I Digital Video Blue 7 Input.
67 DBI6 I Digital Video Blue 6 Input.
68 DBI5 I Digital Video Blue 5 Input.
69 DBI4 I Digital Video Blue 4 Input.
70 DBI3 I Digital Video Blue 3 Input.
71 DBI2 I Digital Video Blue 2 Input.
72 DBI1 I Digital Video Blue 1 Input.
73 DBI0 I Digital Video Blue 0 Input (LSB).
74 GND3.3DRI --- Ground Digital Ram Interface.
75 VSUP3.3DRI --- Supply Voltage Digital Ram Interface, 3.3 V.
76 GND3.3COM --- Ground Common.
77 VSUP3.3COM --- Supply Voltage Common, 3.3V.
78 XTALIN I Analog Crystal Input.
79 XTALOUT O Analog Crystal Output.
80 CLKOUT O Digital 20MHz Clock Output.
81 VSO O TP3059
82 HSO O TP3058
83 SCL I/O I2C Bus Clock Input/Output.
84 SDA I/O I2C Bus Data Input/Output.
85 GND3.3FL --- Ground Flash.
86 VSUP3.3FL --- Supply Voltage Flash, 3.3 V.
87 CADC5 I KEY2 operation key input.
88 CADC6 I KEY1 operation key input.
89 P2_2 I IRIN Remote control input.
90 P2_3 I KEY_PSW Power switch input.
91 P2_4 O V_TXD RS232C TX
92 P2_5 I V_RXD RS232C RX
93 OSDV DBO2_0 I/O TP3042
94 OSDH DBO2_1 I/O TP3041
95 GND3.3IO1 --- Ground Digital Input/Output Port 1
96 VSUP3.3IO1 --- Supply Voltage Input/Output Port 1, 3.3 V
97 OSD_CLK I N.C.
98 OSD_FSW I N.C.
99 OSDHCS1 P3_6 I/O TP3021
100 OSDHCS0 P3_7 I/O TP3020
101 OSDB3 P3_5 I/O TP3019
102 OSDB2 P3_4 I/O TP3018
103 OSDB1 I/O N.C.
104 OSDB0 I/O N.C.
105 OSDG3 P3_3 I/O TP3017
106 OSDG2 P3_2 I/O TP3016
107 OSDG1 I/O N.C.
108 OSDG0 I/O N.C.
109 OSDR3 P3_1 I/O TP3015
110 OSDR2 P3_0 I/O TP3014
111 OSDR1 I/O N.C.
112 OSDR0 I/O N.C.
113 GND3.3IO1 --- Ground Digital.
114 VSUP3.3IO1 --- Supply Voltage Port 1, 3.3 V
5 10
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Pin No. Pin Name I/O Pin Function
115 PCS5 O TP3045
116 PCS4 O TP3043
117 PCS3 O TP3044
118 PCS2 O TP3034
119 PCS1 O TP3033
120 PCS0 O TP3032
121 PCLK2 O TP3022
122 PCLK1 O TP3031
123 GND1.8DIG --- Ground Digital Core
124 VSUP1.8DIG --- Supply Voltage Digital Core, 1.8 V.
125 LVDSA_4P O TP3030
126 LVDSA_4N O TP3029
127 VSUP3.3LVDS --- Supply Digital Voltage LVDS2 Port, 3.3 V.
128 LVDSA_3P O LVDS Channel 1 bit 3 Positive Output.
129 LVDSA_3N O LVDS Channel 1 bit 3 Negative Output.
130 GND3.3LVDS --- Ground Digital LVDS2, 3.3 V.
131 LVDSA_CLKP O LVDS Channel 1 Clock Positive Output.
132 LVDSA_CLKN O LVDS Channel 1 Clock Negative Output.
133 VSUP3.3LVDS --- Supply Digital Voltage LVDS2, 3.3 V.
134 LVDSA_2P O LVDS Channel 1 bit 2 Positive Output.
135 LVDSA_2N O LVDS Channel 1 bit 2 Negative Output.
136 GND3.3LVDS --- Ground Digital LVDS2, 3.3 V.
137 LVDSA_1P O LVDS Channel 1 bit 1 Positive Output.
138 LVDSA_1N O LVDS Channel 1 bit 1 Negative Output.
139 VSUP3.3LVDS --- Supply Digital Voltage LVDS2, 3.3 V.
140 LVDSA_0P O LVDS Channel 1 bit 0 Positive Output.
141 LVDSA_0N O LVDS Channel 1 bit 0 Negative Output.
142 VSUP1.8LVDS --- Supply Analog Voltage LVDS2, 1.8 V.
143 REXT O LVDS External Resistor 2.
144 GND1.8LVDS --- Ground Analog LVDS2, 1.8 V.
145 LVDSB_3P O TP3028
146 LVDSB_3N O TP3027
147 GND3.3LVDS --- Ground Digital LVDS2, 3.3 V.
148 LVDSBCLKP O TP3026
149 LVDSBCLKN O TP3025
150 VSUP3.3LVDS --- Supply Digital Voltage LVDS2, 3.3 V.
151 LVDSB_2P O TP3024
152 LVDSB_2N O TP3023
153 GND3.3LVDS --- Ground Digital LVDS2, 3.3 V.
154 LVDSB_1P O TP3013
155 LVDSB_1N O TP3012
156 VSUP3.3LVDS --- Supply Digital Voltage LVDS2, 3.3 V.
157 LVDSB_0P O TP3010
158 LVDSB_0N O TP3011
159 CADC4 I IF AGC For AGC adjustment.
160 CADC3 I SLOWSW_1I SLOW SW1 input.
161 CADC2 I SLOWSW_2I SLOW SW2 input.
162 CADC1 I TP3009
163 GND3.3DAC --- Ground DAC.
164 VSUP3.3DAC --- Supply Voltage DAC, 3.3V.
165 PWM3 O ST_RS
166 PWM2 O BL_ON Back-light on.
167 PWM1 O OFL1 Modulated light signal.
168 REV O TP3005
169 VSUP1.8FE --- Supply Voltage Analog Video Frontend, 1.8 V.
170 VSUP3.3FE --- Supply Voltage Analog Video Frontend, 3.3 V.
171 DHS I Digital Video H-Sync Input.
172 VIN21 I Analog Video 21 B HD Input.
173 VIN20 I Analog Video 20 G HD Input.
174 VIN19 I Analog Video 19 R HD Input.
175 VIN18 I Analog Video 18 Fast Blank 2 Input.
176 VIN17 I Analog Video 17 B HD Input.
177 VIN16 I Analog Video 16 G HD Input.
178 VIN15 I Analog Video 15 R HD Input.
5 11
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Pin No. Pin Name I/O Pin Function
179 VIN13 I Analog Video 13 B HD Input.
180 VIN12 I Analog Video 12 G HD Input.
181 VIN11 I Analog Video 11 R HD Input.
182 VIN9 I Analog Video 9 Y or B SD Input.
183 VIN8 I Analog Video 8 C or Fast Blank 1 Input.
184 VIN7 I Analog Video 7 Y or G SD Input.
185 VSUP1.8FE --- Supply Voltage Analog Video Frontend, 1.8 V.
186 GNDA --- Analog Video Frontend, Platform Ground.
187 VIN6 I Analog Video 6 C or R SD Input.
188 VIN5 I Analog Video 5 Y/CVBS Input.
189 VIN3 I Analog Video 3 CVBS Input.
190 VIN2 I Analog Video 2 CVBS Input.
191 VIN1 I Analog Video 1 CVBS Input.
192 VSUP3.3VO --- Supply Voltage Analog Video Output, 3.3 V.
193 VOUT3 O TP3002
194 VOUT2 O Analog CVBS Video 2 Output.
195 VOUT1 O Analog CVBS Video 1 Output.
196 GND3.3IO3 --- Ground Digital Input/Output Port 1.
197 VSUP3.3IO3 --- Supply Voltage Input/Output Port 1, 3.3 V.
198 656I0 P3_0 I DTM_IRQI Interrupt from DTV.
199 656I1 P3_1 I/O AVLINK_1
200 656I2 P3_2 I/O AVLINK_2
201 656I3 P3_3 I/O HDMI_INT_I Interrupt from receiver.
202 656I4 P3_4 I/O HDMI_INT_I Interrupt from receiver.
203 656I5 P3_5 O HOTP_CONT0 HDMI plug detection.
204 656I6 P3_6 I MIC_IREQ Interrupt from microcomputer.
205 656I7 P3_7 O HOTP_CONT1 HDMI plug detection.
206 656CLKI I N.C.
207 656CLKO O N.C.
208 P4_7 I HP_PLG Headphone detection.
5 12
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
10. IC4001 (RH-IXC243WJZZQ)
This is a video/ audio signal processing IC (Set-top-box decoder) for digital tuner, incorporates a CPU. In this equipment, it implements GUI process-
ing and video/audio processing for digital tuner, negotiation processing with CI-CARD, etc.
5 13
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Pin No. Pin Name I/O Pin Function
201 LMIDATA15 I/O Bidirectional data.
199 LMIDATA14 I/O
198 LMIDATA13 I/O
197 LMIDATA12 I/O
194 LMIDATA11 I/O
192 LMIDATA10 I/O
191 LMIDATA9 I/O
190 LMIDATA8 I/O
180 LMIDATA7 I/O
178 LMIDATA6 I/O
175 LMIDATA5 I/O
174 LMIDATA4 I/O
171 LMIDATA3 I/O Bidirectional data.
169 LMIDATA2 I/O
168 LMIDATA1 I/O
167 LMIDATA0 I/O
208 LMIADDR12 O Address.
209 LMIADDR11 O
157 LMIADDR10 O
210 LMIADDR9 O
211 LMIADDR8 O
213 LMIADDR7 O
214 LMIADDR6 O
215 LMIADDR5 O
216 LMIADDR4 O
150 LMIADDR3 O
152 LMIADDR2 O
153 LMIADDR1 O
154 LMIADDR0 O
159 LMIBA1 O Bank select.
160 LMIBA0 O
182 LMIDQM0 O Data I/O mask lower.
186 LMIDQM1 O Data I/O mask upper.
181 LMIDQS0 O Data strobe lower.
188 LMIDQS1 O Data strobe upper.
162 NOT_LMICS O Chip select.
163 NOT_LMIRAS O Latch row address strobe.
164 NOT_LMICAS O Latch column address strobe.
206 LMICLKEN O Clock enable.
203 LMICLK O Clock.
202 NOT_LMICLK O Inverted clock.
183 LMI_VREF I Input reference voltage.
166 LMIRDNOTWR O Write enable signal.
Analog audio DAC pins
28 OUTLMINUS O Audio DAC left differential current output.
24 OUTRMINUS O Audio DAC right differential current output.
29 OUTLPLUS O Audio DAC left differential current output.
25 OUTRPLUS O Audio DAC right differential current output.
23 VGBOUT O Audio DAC filtered output reference voltage.
26 IREFADAC I Current reference for Audio DAC.
Digital audio pins
37 S/PDIF O Digital audio.
Analog video DAC pins
15 VDAC1OUT O Video DAC outputs.
16 VDAC2OUT O
17 VDAC3OUT O
18 VDAC4OUT O
14 GNDREXTVDAC I Video DAC external resistor ground.
13 REXTVDACRGB I VDAC external resistor input.
Transport stream pins
35 TS0INBITCLK I TSIN0 Parallel//Serial in.
33 TS0INBITCLKVALI I
D
34 TS0INPACKETCLK I
36 TS0INDATA7 I
5 14
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Pin No. Pin Name I/O Pin Function
Programmable I/O pins
127 POI0[7] I/O PIO PORT 0
126 PIO0[6]
123 PIO0[5]
122 PIO0[4]
121 PIO0[3]
120 PIO0[2]
119 PIO0[1]
118 PIO0[0]
46 PIO1[7] I/O PIO PORT 1
45 PIO1[6]
44 PIO1[5]
43 PIO1[4]
41 PIO1[3]
40 PIO1[2]
39 PIO1[1]
38 PIO1[0]
117 PIO2[7] I/O PIO PORT 2
116 PIO2[6]
115 PIO2[5]
114 PIO2[4]
111 PIO2[3]
110 PIO2[2]
109 PIO2[1]
108 PIO2[0]
12 PIO3[6] I/O PIO PORT 3
11 PIO3[5]
10 PIO3[4]
7 PIO3[3]
6 PIO3[2]
5 PIO3[1]
4 PIO3[0]
JTAG test access port (TAP) pins
134 TDI I TAP boundary scan test data input.
133 TMS I TAP boundary scan test mode select.
137 TCK I TAP boundary scan test clock.
135 NOT_TRST I TAP boundary scan test logic reset.
132 TDO O TAP boundary scan test data output.
DCU pins
1 DCUTRIGGERIN I External trigger input to DCU.
2 DCUTRIGGEROUT O Signal to trigger external debug circuitry.
Analog power supply pins (Audio DAC)
32 VDDAADAC --- 3.3v power for audio DAC.
31 GNDAADAC --- Ground for audio DAC.
30 VSSUBANA --- Substrate ground for all DACs.
Analog power supply pins (Video DAC)
22 VDDDAC0 --- 3.3 V power supply for video DAC 1, 2 and 3.
21 VDDDAC1 --- 3.3 V power supply for CVBS video DAC 4.
19 VSSDAC0 --- Ground for video DAC 1, 2 and 3.
20 VSSDAC1 --- Ground for video DAC 4.
Analog power supply pins (Frequency synthesizers)
140 VDDDFS1 --- Frequency synthesizer 1.2 V digital power dedicated to frequency synthesizer 1.
141 GNDDFS1 --- Frequency synthesizer 1.2 V digital ground dedicated to frequency synthesizer 1.
142 VCCAFS --- Frequency synthesizer 1.2 V analog power shared between frequency synthesizer
1 and 2.
143 GNDAFS --- Frequency synthesizer 1.2 V analog ground shared between frequency synthe-
sizer 1 and 2.
144 GNDDFS2 --- Frequency synthesizer 1.2 V digital ground dedicated to frequency synthesizer 2.
145 VDDDFS2 --- Frequency synthesizer 1.2 V digital power dedicated to frequency synthesizer 2.
Analog power supply pins (PLLs)
146 VCCAPLL --- 1.2V PLL1 analog power.
147 GNDAPLL --- 1.2V PLL1 analog ground.
148 GNDAPLL1 --- 1.2V PLL2 analog ground.
149 VCCAPLL1 --- 1.2V PLL2 analog power.
Analog power supply pins (LMI SDRAM)
5 15
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Pin No. Pin Name I/O Pin Function
184 VDDDLL --- 1.2 V for DLL.
185 GNDDLL --- Ground for DLL.
176 VDDDE0 --- 1.2 V for delay element 1.
177 VSSDE0 --- Ground for delay element 1.
196 VDDDE1 --- 1.2 V for delay element 2.
195 VSSDE1 --- Ground for delay element 2.
Digital power supply pins
8, 47, 67, 101, 124, 155, 173, VDD12 --- 1.2 V digital power supply.
204
151, 158, 165, 170, 179, 187, VDD25 --- 2.5 V power supply when connected to DDR SDRAM on the LMI interface.
193, 200, 207, 212
3, 42, 55, 72, 84, 96, 113, 129 VDD33 --- 3.3 V power supply.
EP1, 9, 27, 48, 54, 68, 102, GND --- Ground.
112, 125, 136, 156, 161, 172,
189, 205
5 16
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
5 17
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
12. IC4251 (RH-IXC361WJZZQ)
This IC is a high performance CMOS super technology 16Mbit Flash Memory.
Start software (loader) for the CPU with a built-in digital processor and application software have been written on this Flash Memory.
The digital processor reads these soft wares on start-up and implements them.
5 18
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
14. IC8103 (VHIT3Z18AFG-1Q)
Single Link LCD Receiver
The LVDS is essentially a signaling method used for high-speed transmission of binary data over copper.
It uses a lower voltage swing than other transmission standards. This low voltage differential is what delivers higher data transmission speeds and
inherently greater bandwidth at lower power consumption.
This new technology not only addresses the needs of todays high performance data transmission application, but also the needs of future applica-
tion.
This LVDS receiver IP supports Single Link transmission between Host and Flat Panel Display. The receiver recovers the LVDS data and converts
into CMOS data. An on-chip PLL synchronizes the received clock with the parallel data and then all are transmitted to the parallel output port of the
receiver.
Description:
Supports Single Link (Single Input to Single Output) up to 135MHz dot clock for SXGA+ (input clock frequency: 25 to 135MHz)
PLL requires no external components
Clock strobe edge selectable
Support 10-bit color
Power down mode
Pin No. Pin Name I/O Function Name Pin No. Pin Name I/O Function Name
1 PLLAVD 1.5V E1AVDLIVC 141 SCLK OUT BT4VIC1
2 PLLAVS GND E1AVSLIVC 142 SDT I/O BD4THVIC1
3 VSSAGND45L GND Z7RSTAGND45L 143 vext1103 1.5V SDRAMVDE1
4 VDDSAVCC4 3.3V Z7RSTAVCC4 144 VDDC 1.5V VDDC
5 VSSAGND45C GND Z7RSTAGND45C 145 RESET IN SMTCIF
6 VDDSAVCC5 3.3V Z7RSTAVCC5 146 CMOS_IN IN IBUFDIF
7 BR0_M OUT Z7RSDST 147 OS_SEL IN TLCHTHDVIC1
8 BR0_P OUT Z7RSDST 148 OS_ON IN TLCHTHDVIC1
9 BR1_M OUT Z7RSDST 149 BANK_SEL IN TLCHTHDVIC1
10 BR1_P OUT Z7RSDST 150 TEMP[2] IN TLCHTHDVIC1
11 BR2_M OUT Z7RSDST 151 vgnd87 GND SDRAMVSE
12 BR2_P OUT Z7RSDST 152 TEMP[1] IN TLCHTHDVIC1
13 BR3_M OUT Z7RSDST 153 TEMP[0] IN TLCHTHDVIC1
14 BR3_P OUT Z7RSDST 154 REV_MODE IN TLCHTHDVIC1
15 BCLK_M OUT Z7RSDST 155 HSCAN IN TLCHTHDVIC1
16 BCLK_P OUT Z7RSDST 156 VSCAN IN TLCHTHDVIC1
17 VDDSAVCC4 3.3V Z7RSTAVCC4 157 vext1105 1.5V SDRAMVDE1
18 VSSDGND1 GND Z7RSTDGND1 158 VSS12 GND VSS12
19 VDDCDVCC1 1.5V Z7RSTDVCC1 159 SELLVDS IN TLCHTHUVIC1
20 VSSAGND45C GND Z7RSTAGND45C 160 SSCLK I/O BD8SCIF
21 VDDSAVCC5 3.3V Z7RSTAVCC5 161 EXCLK IN IBUFIF
22 BG0_M OUT Z7RSDST 162 VDDC 1.5V VDDC
23 BG0_P OUT Z7RSDST 163 VSSAGND1L GND Z7LVRAGND1L
24 BG1_M OUT Z7RSDST 164 RA_M IN Z7LVRXIO
25 BG1_P OUT Z7RSDST 165 RA_P IN Z7LVRXIO
26 BG2_M OUT Z7RSDST 166 RB_M IN Z7LVRXIO
27 BG2_P OUT Z7RSDST 167 RB_P IN Z7LVRXIO
28 BG3_M OUT Z7RSDST 168 RC_M IN Z7LVRXIO
29 BG3_P OUT Z7RSDST 169 RC_P IN Z7LVRXIO
30 VDDSAVCC4 3.3V Z7RSTAVCC4 170 VDDAVDD1L 3.3V Z7LVRAVDD1L
31 VSSDGND1 GND Z7RSTDGND1 171 L_VDDPLL1 2.5V Z7LVRVDDPLL1
32 VDDCDVCC1 1.5V Z7RSTDVCC1 172 L_VSSPLL1 GND Z7LVRVSSPLL1
33 VSSAGND45C GND Z7RSTAGND45C 173 L_VDDPLL2 2.5V Z7LVRVDDPLL2
34 VDDSAVCC5 3.3V Z7RSTAVCC5 174 L_VSSPLL2 GND Z7LVRVSSPLL2
35 BB0_M OUT Z7RSDST 175 L_VDDD 1.5V Z7LVRVDDD
36 BB0_P OUT Z7RSDST 176 L_VSSD GND Z7LVRVSSD
37 BB1_M OUT Z7RSDST 177 PVDDA1B 2.5V Z7LVRVDDPLL1*1
38 BB1_P OUT Z7RSDST 178 PVDDA2B 2.5V Z7LVRVDDPLL2*1
39 BB2_M OUT Z7RSDST 179 VDDS_L 3.3V Z7LVRVDDS
40 BB2_P OUT Z7RSDST 180 PVSSA1B GND Z7LVRVSSPLL1*1
41 BB3_M OUT Z7RSDST 181 PVSSA2B GND Z7LVRVSSPLL2*1
42 BB3_P OUT Z7RSDST 182 VDDC_L 1.5V Z7LVRVDDC
43 VDDCLCDVDDC 1.5V Z7RSTVDDC 183 VDDAVDD2 2.5V Z7LVRAVDD2
44 VSSLCDVSS2 GND Z7RSTVSS2 184 VSSAGND2 GND Z7LVRAGND2
45 VSSAGND45R GND Z7RSTAGND45R 185 VDDAVDD1R 3.3V Z7LVRAVDD1R
5 19
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Pin No. Pin Name I/O Function Name Pin No. Pin Name I/O Function Name
46 vgnd0 GND SDRAMVSE 186 RCLKM IN Z7LVRXIO
47 vext10 1.5V SDRAMVDE1 187 RCLKP IN Z7LVRXIO
48 LS_B OUT B4IF 188 RD_M IN Z7LVRXIO
49 SPB1 OUT BT8IF 189 RD_P IN Z7LVRXIO
50 SPB2 OUT BT8IF 190 RE_M IN Z7LVRXIO
51 VDDS 3.3V VDDS 191 RE_P IN Z7LVRXIO
52 VSS12 GND VSS12 192 VSSAGND1R GND Z7LVRAGND1R
53 REV OUT B4IF 193 VDDC 1.5V VDDC
54 vext12 1.5V SDRAMVDE1 194 CLKOUT OUT Z7DDRVO
55 GOE OUT B4IF 195 VDDS 3.3V VDDS
56 GCK OUT B4IF 196 VCSV1 OUT B4IF
57 GSP1 OUT BT4IF 197 VCSV2 OUT B4IF
58 GSP2 OUT BT4IF 198 VCSV3 OUT B4IF
59 GSLOP OUT B4IF 199 VCSV4 OUT Z7DDRVO
60 VPOL I/O BD4CIF 200 VCSV_Z OUT B4IF
61 VDDC 1.5V VDDC 201 VSS12 GND VSS12
62 VSS12 GND VSS12 202 SPA2 OUT BT8IF
63 ROM256 IN IBUFDIF 203 SPA1 OUT BT8IF
64 MASTER IN IBUFDIF 204 LS_A OUT B4IF
65 vext13 1.5V SDRAMVDE1 205 VDDS 3.3V VDDS
66 vgnd2 GND SDRAMVSE 206 VSSAGND45L GND Z7RSTAGND45L
67 EX_DT[0] I/O BD4CIF 207 VDDCLCDVDDC 1.5V Z7RSTVDDC
68 EX_DT[1] I/O BD4CIF 208 VSSLCDVSS2 GND Z7RSTVSS2
69 vext21 2.5V SDRAMVDE2 209 FR0_M OUT Z7RSDST
70 vgnd3 GND SDRAMVSE 210 FR0_P OUT Z7RSDST
71 vext147 1.5V SDRAMVDE1 211 FR1_M OUT Z7RSDST
72 vgnd37 GND SDRAMVSE 212 FR1_P OUT Z7RSDST
73 vext22 2.5V SDRAMVDE2 213 FR2_M OUT Z7RSDST
74 EX_DT[2] I/O BD4CIF 214 FR2_P OUT Z7RSDST
75 VDDS 3.3V VDDS 215 FR3_M OUT Z7RSDST
76 VSS12 GND VSS12 216 FR3_P OUT Z7RSDST
77 EX_DT[3] I/O BD4CIF 217 FCLK_M OUT Z7RSDST
78 EX_DT[4] I/O BD4CIF 218 FCLK_P OUT Z7RSDST
79 EX_DT[5] I/O BD4CIF 219 VDDSAVCC4 3.3V Z7RSTAVCC4
80 EX_DT[6] I/O BD4CIF 220 VSSDGND1 GND Z7RSTDGND1
81 EX_DT[7] I/O BD4CIF 221 VDDCDVCC1 1.5V Z7RSTDVCC1
82 EX_DT[8] I/O BD4CIF 222 VSSAGND45C GND Z7RSTAGND45C
83 EX_DT[9] I/O BD4CIF 223 VDDSAVCC5 3.3V Z7RSTAVCC5
84 EX_DT[10] I/O BD4CIF 224 FG0_M OUT Z7RSDST
85 EX_DT[11] I/O BD4CIF 225 FG0_P OUT Z7RSDST
86 EX_DT[12] I/O BD4CIF 226 FG1_M OUT Z7RSDST
87 EX_DT[13] I/O BD4CIF 227 FG1_P OUT Z7RSDST
88 EX_DT[14] I/O BD4CIF 228 FG2_M OUT Z7RSDST
89 VDDS 3.3V VDDS 229 FG2_P OUT Z7RSDST
90 VSS12 GND VSS12 230 FG3_M OUT Z7RSDST
91 EX_DT[15] I/O BD4CIF 231 FG3_P OUT Z7RSDST
92 EX_SPIO I/O BD4CIF 232 VDDSAVCC4 3.3V Z7RSTAVCC4
93 VDDC 1.5V VDDC 233 VSSDGND1 GND Z7RSTDGND1
94 VSS12 GND VSS12 234 VDDCDVCC1 1.5V Z7RSTDVCC1
95 EX_CLKI IN IBUFIF 235 VSSAGND45C GND Z7RSTAGND45C
96 EX_CLKO OUT B8IF 236 VDDSAVCC5 3.3V Z7RSTAVCC5
97 EX_DT[16] I/O BD4CIF 237 FB0_M OUT Z7RSDST
98 EX_DT[17] I/O BD4CIF 238 FB0_P OUT Z7RSDST
99 EX_DT[18] I/O BD4CIF 239 FB1_M OUT Z7RSDST
100 EX_DT[19] I/O BD4CIF 240 FB1_P OUT Z7RSDST
101 EX_DT[20] I/O BD4CIF 241 FB2_M OUT Z7RSDST
102 EX_DT[21] I/O BD4CIF 242 FB2_P OUT Z7RSDST
103 VSS12 GND VSS12 243 FB3_M OUT Z7RSDST
104 VDDS 3.3V VDDS 244 FB3_P OUT Z7RSDST
105 EX_DT[22] I/O BD4CIF 245 VDDCLCDVDDC 1.5V Z7RSTVDDC
106 EX_DT[23] I/O BD4CIF 246 VSSLCDVSS2 GND Z7RSTVSS2
107 EX_DT[24] I/O BD4CIF 247 VDDSAVCC4 3.3V Z7RSTAVCC4
108 EX_DT[25] I/O BD4CIF 248 R_VDDPLL1 2.5V Z7RSTDDRV25
109 EX_DT[26] I/O BD4CIF 249 R_VDDPLL2 2.5V Z7RSTDDRV25
5 20
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Pin No. Pin Name I/O Function Name Pin No. Pin Name I/O Function Name
110 EX_DT[27] I/O BD4CIF 250 R_VSSPLL1 GND Z7RSTDDRVGND
111 EX_DT[28] I/O BD4CIF 251 R_VSSPLL2 GND Z7RSTDDRVGND
112 VDDC 1.5V VDDC 252 R_VDD15 1.5V Z7RSTDDRV15
113 VSS12 GND VSS12 253 R_VSS15 GND Z7RSTDDRVGND
114 EX_DT[29] I/O BD4CIF 254 VSSAGND45C GND Z7RSTAGND45C
115 vext158 1.5V SDRAMVDE1 255 VDDSAVCC5 3.3V Z7RSTAVCC5
116 VDDS 3.3V VDDS 256 VSSAGND45R GND Z7RSTAGND45R
117 VSS12 GND VSS12
118 vgnd50 GND SDRAMVSE
119 vext26 2.5V SDRAMVDE2
120 vgnd84 GND SDRAMVSE
121 EX_DT[30] I/O BD4CIF
122 EX_DIR I/O BD4CIF
123 TEST_C IN IBUFDIF
124 TEST_L[3] IN IBUFDIF
125 TEST_L[2] IN IBUFDIF
126 TEST_L[1] IN IBUFDIF
127 vgnd85 GND SDRAMVSE
128 vext1102 1.5V SDRAMVDE1
129 TEST_L[0] IN IBUFDIF
130 DAC_DATA OUT B4IF
131 DAC_CLK OUT B4IF
132 DAC_LATCH OUT B4IF
133 READY OUT B4IF
134 S_LBR OUT B4IF
135 G_LBR OUT B4IF
136 VDDS 3.3V VDDS
137 VSS12 GND VSS12
138 G_LBR_INV OUT B4IF
139 FS OUT B4IF
140 SREADY I/O BD4THVIC1
*Pin No.177, 178 is a power supply for SSCG, Pin No.180, 181 is GND for SSCG, and it is separated with another power supply GND.
5 21
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Pin No. Pin Name I/O Pin Function
16 OUT2 O Gradation voltage output terminal 2.
17 OUT3 O Gradation voltage output terminal 3.
18 OUT4 O Gradation voltage output terminal 4.
19 OUT5 O Gradation voltage output terminal 5.
20 AGND --- Buffer amplifier ground.
21 AGND --- Buffer amplifier ground.
22 OUT6 O Gradation voltage output terminal 6.
23 OUT7 O Gradation voltage output terminal 7.
24 OUT8 O Gradation voltage output terminal 8.
25 OUT9 O Gradation voltage output terminal 9.
26 OUT10 O Gradation voltage output terminal 10.
27 OUT11 O Gradation voltage output terminal 11.
28 VCC --- Buffer amplifier power supply.
29 REFIN O DAC reference input.
30 VDAC O DAC voltage output.
31 DACGND --- Ground for DAC.
32 N.C --- No Connect.
5 22
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
Pin No. Pin Name I/O Pin Function
25 VCP2 O Charge pump LOD output 2.
26 HVCC --- Power supply terminal.
27 VCP1 O Charge pump LOD output 1.
28 C1 O Charge pump output 1.
29 CPPG O CP power good output.
30 CPFB1 I Charge pump feedback 1.
31 PGND1 --- Ground terminal.
32 PG1 O Power good output 1.
33 SW1 O Switching output 1.
34 PGATE O P-channel gate drive output.
35 DTC1 I Duty control terminal 1.
36 COMP1 O Error margin amplifier output 1.
37 FB1 I Feedback input 1.
38 CTL1 I Control input 1.
39 FAULT O Protect detector output.
40 SCP I Short protection delay terminal
41 UVLO I Low voltage lockout setting terminal.
42 VCC --- Power supply terminal.
43 VREF O Reference voltage output terminal.
44 FB2 I Feedback input 2.
45 COMP2 O Error margin amplifier output 2.
46 DTC2 I Duty control terminal 2.
47 PVCC2 --- Power supply terminal.
48 BOOT2 I Switch boot terminal 2.
49 SW2 O Switching output 2.
50 CTL2 I Control input 2.
51 PG2 O Power good output 2.
52 REG O LDO output for BOOT.
53 LDFB1 I LDO feedback 1.
54 LDCTL1 I LDO control terminal 1.
55 LDPG1 O LDO power good output 1.
56 LDO1 O LDO output 1.
57 GND --- Ground terminal.
58 RT I Frequency setting terminal.
59 LDFB2 I LDO feedback 2.
60 LDO2 O LDO output 2.
61 LDVCC2 --- Power supply terminal.
62 CTL3 I Control input 3.
63 SW3 O Switching output 3.
64 BOOT3 I Switch boot terminal 3.
5 23
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
LC32D44E-BK
CHAPTER 6. BLOCK DIAGRAM/OVERALL WIRING Service Manual
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
61
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
62
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
63
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
64
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
71
R8256
R4240 R4241
R4245 R4246
C4225
C4402
FB4202
FB4201
R4243 C4231
C4233 R4244
C4401
R216
R4242
C4229
FB4001
FB4401
C4223
C4224
C238
C257
R238 IC206 R220
R237 C8218
R219
R217
C3073
C3072
C3071
R239 R240 R8255 LUG3006
R236 C8202
C8225 C8229 C8228
R221
C258 L8108 L8107 C8226
L8114
L8113
C4221 L8102 L8101
R233 L8112 L8111 L8110 L8109
L8106
L207
R231
LUG3001
C4257
C4258
IC207 R8254
R230
LUG1705
R4235
R223
R222
I C4202
C4201
R4268
R228 R229
R210
C254 C253
C4218
R218
IC203
C206
C4219
C252
C247
R206
C4214 C249 C243 R8253
R227
R226
C8470 R8435
R8438 R8434
C4208 C240
C4210
C234 R8432
C233
C8422
C8407 D8406
C235
C4206
R4430 R8148
Q8405
R8439 C8406
C4207
C4204
R4426 R8252
C8142
C8136
R4405 C232 C227 C207 Q8411 Q8412
C4203 R4437
C203
C8452 FB8105
L8402
C4205 R4431
R8442 R8441
C8423 R8443
R4432 R8489 Q8403 R8422
R8463
R8471
R8482
D8407
R8487 R8429
IC8103
C223
R4218
C8471
C8462
IC201
R8430 R8444
C8448
R8423
D8408
R8251 R8484
C8412
C8419
R4417 R8486
H R8149 C8441 R8436
C4011
C4006
C4007
C4005
C4009
IC8403
R8456
R8502
C4410
R4441
R4423 C8416
R215
C212
R8143
IC8404
R8473
R8440 R8437
C8414 R8433
C211 R8142 C8440
C4014 R8470
SC4401
C8417
R8410
C4015 C4420 R8467
C4012
C4003
C4004
C4010
C4062 C8439
C4017
C4416
C4415
D8405
C4018 R4003 C217 R8146
C4419
C8449 R8464
R8469
IC8402
C4020 R214 R8145 C8433 C8438 R8498
C4019
R8428
C8411
R8427
C4021 R8472
C4022 Q203 R213 C8102 R8445
C4024 C8453 C8425 C8424
R4445
R4447
C4417
Q8414
FB4402
C4421
R8425
R4007 IC4410 C213 C8458
C216
C8436
D1725
C8418
R4006
D8402
R211
R212
R8121
R4436 C1765 R8136 R8450 R8454 R8455
R4018
C1728 R8137 R8128 R8115
C1760
C4030 R8104 C8415 R8449 C8421
C1764 R8131 R8124
C4029 R8234 R8233 R8132 R8126
FL8101 C8429 D8409
R4009 C1727 D1756 R8230 C8219 R8133 R8108
C4033 C4034 C271 R8134 R8110
C8217 R8228 R8130 R8112 C8410 R8459
R8420
C8402
R8135 R8116
R8460
C4035
G
C8413
C8468
C4031 C8216 R8226 R8106 R8451 C8473
C8135
C4037
C4036
IC1725 R8122
IC1756
C8222
R8215 R8211
C8215 R8223 R8224 C8208 IC8101
R4435 C8214 R8221 C8132
C4038
C4041
C4040
R4017
C4039
R8213 R8210
IC8201
C8223
FB8103
C8101
C8212
R8209
R8225
C1726 C8211 R8219 IC8202
L8403
C4060 C201 C1725 R8217
C1761
C1762
C1763
R1758
C8446
C8445
C8443
C8210 R8214 R8216 R3005 R8218 R8505
C8213
R8222
R8227
R8229
C8209 R8212 D8101
C8207 R8208 C8206
R8504
R8203
C8205 R8205 R8207
R8206
C4063 D8403 D8404
R8507
R8202
C2610
C8463
C8427
C1413 R8204
C8201
R2615
R8499
IC2602
C8204 R2613 R2612
C8203
D8410
C8480
R8508
C1414 C1411 R2614
IC1401
C1416
FB4002 C1409 C8464
R4030 R4021 C1417
R4264
L8401
C1405
C1415
R8408
C4254
F R4265 R4266 Q4251
P8101
R4267
R4262
R4263
C4059
C8461
C4058
C4052
R4041
C4252
C4253
FB4251
R4040
R4039 R4272
LUG3003
C4053
P4002
C1321 C1324
R1320
C1328
R1324
C1329
R1328
R4038
C1319
C1322
C4049 Q1501
R1326
R1506
R8114
FB4003
R1756
C1756
C1323
R4035 R1329
R4034 R1321 R1330 R1327 R1325
IC1755
C1755
C1758 R1322
C2304
L1101
Q1302
C1163
Q1301
C1325 FB1309
C1129
C1128
C1121
C1122
C1403 C2308
D1501
FB1302 C1302
R1303 C1308
R1311 R1308
R1402
P2302
C2307
D1304
D1702
R1503 C1105 C1311 C2302
C1112 L2602 R1706 D1705
C1506
C1505
C1504
C1503
FB1304 C1304
R1304 R1306
R1312 C1306
IC1701
D1101 J1302 L2603
C1508
D1302
C1113 C1507
L1701
D1109
IC1502
L2605
D1102
C1705
D1105 R1505 C1312
L2606
IC1501 C1104
C1110
C1111 D1104
C1115
C1407
C1109
C1715
R1504
R1113
C3024
C1502 R1117
FB1501
R1502
FL1402
LUG3002
C1124
C1719
C1720
R1712
C1123
IC1941
C2020
C2019
C3054 C3055
D1502 C1410 R1123 R1107 D1803
P1701
R1125
D1801
IC1921
R1109
R1924
R1727
C1922
R1960
C1729
IC1726
C1731
FL1108 FL1101 D1114
C1993
R1802
R1803
R1971 C1995 C1973 C1971 C1953 R3008
Q1801
C1117 FB1103 IC3051
R1801
C1802
C1106
FL1403
D1112 VA1928 R1731
R1128
D1802
D1805
LUG1701
SC1921
X3051
VA1921 FB1735
D1735
C1118 C1107 D1115
L1735
D1110
D1206
R3081
C1741
R1203 FB1104 C1127 FB1702
C1116
R2317
IC1735
D1208
R1955
R2303
C1743
R2312
C
C1317 R1316
R1318
R1317
C1318
FB1102 R1103
IC1951
C1744
D1306
C1316 D2702
R2717 R2712 R2713
C2704
C2702
C2701
D1207 R1101
R2304
R2336
D1202
R2709 R2708
LUG1702
C2713
D1108
Q2701
D1205 C1752
C2320
C2321
R2706
R1204 FB1203
C2706
C2712
C2715
C2705
C2708
C2714
C2711
D1745
FB1105 R1146 FB1110
D1201
C1142
C1134
R1138
C1138
R2324
R1143
C1751
C1753
C1149 L1745 IC1745 R1752
R2715
C1132 C1136
R1210 D1203 IC1902 R2716 C2709
Q2305
R1209
R1149 FB1108
C1754
R1208 X2301 IC2303
P3081
C2717
C2718
C1204
R1966
R1970
R1969
R1968
C2319
C2734
C2732
C1141
C1133
R1137
C1137
R1142
C2003
R1131
R1136
R1139
FB1111
R1036
R1035
R1034
Q1904
Q1903
IC2701
R1033
R1135 R1134
C1017
R1144 R1147
C1155
C2725
C2724
C2731
C2707
C2716
C2710
C2723 C2726
C1034
C2730
R2729
C2729
R2722
R2720
R2718
R2721
R2719
C1007 P2303
R1010 IC1001
R1305 R1310
C1309
D1303
C1310
R2731
R2732
R2730
R2728
VA1906 VA1907
C2733
C2735
R1031
R1032
C1033
C1032
C1008
C1011
C2738
C2736
C1315
FB1301
C1313 R1314
VA1901
R1313 R1315 P2701
J1301
C1009
C1010
C1019
C1301 C1012
P2301
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
72
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
73
C4045
Q4002 Q4001 Q4003 Q4004 IC4003 IC4002 C4046
IC4004
C4051
C4057
19
R4010 C4028 C4026 C4013 R4044
R4025
R4032
X4001
R4012
R4206
R4011
C4025
C4023
R4004
R4005
R4202
R4252
R4210 R4211
R4209
18
C4236
C4237
R4260
C4235 R4219
R4204
R4251
R4208
R4259
R4220
IC4201 R4217
R4216 R4215
IC4001
R4255
IC4251
R4203
R4258
R4207
R4213
R4254
R4231 C4234
R4214 R4212
17
C1757
R4205
R4257
R4201
C1759
R1755
R4253
R4019
R4020
R4261
R4016 R4256
R4269
IC4253
IC4252
C4256
R4049
FB4004
C4054
C4050
D4201
C4404
16
IC4409
R1012
C4406
R4448
R1014
C1151 C1152 Q1001
C1130
IC4403
C4409
R1154 R1150
R4418
IC4407 C4061
C4055
R4024
D1117
IC1102 R1013
Q1101
IC4402 IC4404 IC4405
R4045
C4411
IC4408
IC4401 R4026
C4413 C4414
R4043
R4433 R4434
R4455
IC4406
R4454
IC4005 R4031
C4418
C4403
D1118
D1119
C4407
R4028 R1152
C4408
R4406
R4410 R4428 R4422 R4411 R4413 R4415 R4412 R4427 R4421 R4416 C4048
R4414 R4429 C4042
15
IC1002
C4056 R4022 Q1105 Q1106
R4425
R4446
R4042 R4023
R4029
R1156
Q4403
C1016 R1018
R1020 C1014
R1015
C1154
C1153
D1113
C1114
R1151 R1155
R1023 R1021
R1022
Q1102
L206
IC1101
C218 R4453
C222
R4443
14
C244
C242
C1160 C1159
C226
C1102
C241
C1101
IC202
D1120
D1121
L203 R1153
C2301
C237
C248
C239
C250
D2301
IC205
C230
C231
C224
X201
C255 C2312
C225
L204
C2311
IC204
R1157
L205 FB202
FB2305
FB2304
FB2301
FB2302
C221
13
D1906
FB1901
C1903 D1905
FB1902
D1907
D1908
R1909
C1904
D1911
R1902
C1905
R1932
R1912
R1901 Q1905
D1922
D1921
R1921
D1923
R1907
R1903
Q1925
R1914
D1910
C1921
C2322
TH2301
D1901
R1915
12
R1926 D1904 R1904 R1911
D1924
D1909
Q1906
R1930
R1928
D1925
C1332
R1411
R1410
R1409
D3071 FB3071
R1933
D3072 FB3072
FB3073
D3073
C1412
C1408
C1404
C1333
R1331
R1332
FB1957
FB1955
R1405
D1403
D1402
D1401
C1330
C1331
R3056
C2001
C2002
C2004
C2017
C2018
C2016
C2015
C2014
C2013
C2012
C2011
C2010
C2009
C2008
C2007
C2006
C2005
11
C2000
C1997
C1999
C1996
C1998
FB1956 C1994
C1952
C1406 C1992
C1402
C1988 C1990
C1987 C1991 C1986
C1401 C1951
C1989 C1985
C1984
74
C1983
FB1401
FB1402 C1982
C1981
C1980
C1979
R209 C269 C1978 C1976
C210
Q202
FB201 FB1953
C1975 C1962
C209 R225 R235 R283 Q1831 FB1952
C1970
Q262
R266
L263
C1968 C1961 R1961
R1713
C1967
C1969
C1963
C1959
Q204
C1965
R262
R1401 C1966
10
IC261
C1958
C1957
C1956
C1955
C1954
FB1954 C1964
R1958
R224 FB1951
R208 R207 C1960
C208 C204
Q201 R205
D201
R203
C1907
C202
R202
R201
9
R8262
R8261
R8260
R8259
R8258
R8257
R3091
C3035
C3002
C3001
IC3002
C3004
R8481
R8477
R8466 R8462
FB3036
8
C3042
R8485
R8479
C3030
C3041
C8477
R8468
C3045
R3002
R3001
C3028 C3044
C3031
C3037
C3039
C3040
C3029
C3043
FB3035
C3038
FB3004
FB3037
FB3038
C3046
C8460
C8457 R8483 C3008
R8236
C8220
R8235
R8238
C8455 C3015
R8220
FB3003 FB3052
C8221
R8240
R8239
R8241
C3012 C1908
C3053
C3059 Q3052
C3007
IC3052
R8231
FB3002 C3027
Q3051 FB3056
R8232 C3005 C3058
FB3055
C8478
C3009
R3054
C3057
R8475 C3033 C3060
FB3054
C3016
C3082 C3081
R8476 C3020
C3006
C3052
C3076
R8480
R8478
C8454
C8451
C8450
R3074
R3075
R3092
FB3053
C3011
C3034
R3073
C3019
C3051
R3071
C3074
C3075
R3072
FB3005
C3010
C8230 C3018 C3026
R3004
C3021
C3017
C3022
C3023
C3025 FB3022
6
FB3006
FB2309
FB3021
C3047
FB3001
C8122
C3003
R3003
R2320
C8125 C2314
C3014
C3013
C8120
C2602
C8126
IC2301 IC2601
R2314
C8118
R2329
R2326 R2321
R2603
C8127
C8128 R8102
C2601
R2601
R1719
R2325
C8129
C8130
C8144
C2317
R8118
C2316
C8112
R2328
C8114
5
C8110
R2335
C8111
C8124
C8134 C8131
C2323
TH2302
FB8101
C8141
C8123
C8121
C8117
R8123
C8116
R8107
C8119
C8103
R8117
R8113
C1709
R8111
C8115
R8141
R8109
C1737
C1736
C1735
C1747
C1746
C1745
R8140
R8127
C1707
Q1802
R8125
R8129
4
C8104 C1706
FB8106
C1801
C8113
C8105
C8108 R1702
C8106
C8107 R1701
C1710 R1703
C8109 R1736 R1745
C1711
C8133 R1735 R1746
C8139 R1708
C1712 R1714
C8138 C1738 R1737 C1748 R1747
C1713
D1704
C8140 C8137 R1739 R1750
R1740 R1749
C1739 R1743
C1749 R1754
Q8410 C1714
FB8104
FB8102
C8143
D1736
D1703
R1738 R1748
C8479
C1740 C1750
3
R8461 R8458 C1703
C8432 R8418
C1701
R8457 R8416
D1726
Q8401
C1732
R1709
R8447 C1702
C1704
R1705
R8413
R8414
R8415
R1704
C1708
R1730
R1728
R1725
C1730
C1733
R1729
C8442 C1716 C1718
R1710
IC1703
D1701
Q8450
C8227 C8476 C8437
C8430
R8497 R8496
R8403 C8401 C8431
C8467
2
R8494 R8493
R8495
R8409
R8101
C8466 R8492 D8411 R1716
R8417
FB1801
C8231
R8419
Q8402
C8459 C8465 R1717
R8421
C8409
Q8404
R8402 C8472
R2313
C1721
C1722
R8404 C8403
R8506 R1718
R8412
C8404
R2305
R2307
R2306
R2302
R8491
R8452 R8453
R8446 C8469
C8420 R8431
R8406
R8405
C8405
C8435
C8434
C8444 R1715
R8401
C8426
FB1703
C8428
R8407 R8500
1
G
A
H
C
E
F
J
I
LC32D44E/S/RU-BK/GY (1st Eddition)
[2] R/C, LED Unit
R/C, LED Unit (Side A) R/C, LED Unit (Chip Side A) R/C, LED Unit (Side B) R/C, LED Unit (Chip Side B)
J
H
C107
P101
R101
D101
G
C102
SLD101
RMC101
D
D103
R109 R108
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
75
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
76
J
KEY Unit (Side A) KEY Unit (Chip Parts Side A)
I
S155
R153
D152
S154
H
S152
G
R151
D151
S151
F
R152
S153
E
R154
D S156
S157
D155
B
P151
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
77
CAUTION:
This circuit diagram is original one, therefore there may be a slight
difference from yours.
SAFETY NOTES:
1) DISCONNECT THE AC PLUG FROM THE AC OUTLET
BEFORE REPLACING PARTS.
2) SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS
POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS
OPERATING.
81
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
82
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
83
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
84
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
85
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
86
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
87
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
88
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
89
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 10
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 11
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 13
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 14
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 15
MINI AV Unit
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 16
KEY Unit
J
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 17
low power
full power
burst mode
PS_ON
3.2 V
s
n es
ht
rig
e b
or
m
PARTS GUIDE
No. S38F8LC32D44E
MODELS LC-32D44E/S/RU-BK/GY
CONTENTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
2
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
3
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
4
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
5
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
6
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
7
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
8
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
9
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
10
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
11
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
12
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
13
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
14
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
15
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
16
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
17
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
18
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
19
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
[7] CABINET PARTS
28
1
21
1-5
7
1-1
1-6 29
1-6
1-5 22
1-7 38 25
1-2
14
20
24
1-3 17
1-4
13
36 38
12 38 36 38
10
38
8 36
38
15
4
38 5
26
27 36
11
15
9
38
36
36
39
2
12 31
38 38
11
38
2-1
33 2-2
18 34
2-3
37 2-7
19 2-4
3 30 2-3 35
2-7
2-3 2-6
16
3-1 2-7
23 2-4
3-2
40
37
20
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
21
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
[8] LCD MODULE ASSEMBLY
4-1
4-4
4-3 4-2
4-5
4-7
4-6
4-8
4-9
4-10
4-12
4-11 4-17
4-14 4-18
4-16
4-13
4-15
22
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
X3 X12
X2 X1
X12-1
X8
X11 X4 X5 X6 X7 X9
X10
23
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
[10] PACKING PARTS
S10
S9
S8
S8
S3
S5
S6
S7
S11
S2
S4
S8
S8 S11
S1
24
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
25
Downloaded from www.Manualslib.com manuals search engine
LC32D44E/S/RU-BK/GY (1st Eddition)
SHARP CORPORATION
AV Systems Group
CS Promotion Center
Mar. 2008
TQ -S SH. DS Yaita,Tochigi 329-2193, Japan