Shanghai Meng Yan Automation Equipment Co. http://www.monsun.

cn
installation before use precautions:

Previous check the dc controller model specifications are with the stationary
requirements. If it does not meet the requirements of an order please contact th
e manufacturer

before installation. Please check the dc controller information and spare parts
is complete
(specific inspection packing list value of the Instructions for Use of the quali
fied product license; 3
user Quality Feedback Form 4 (annex to the spare parts were spare parts when ord
ering the request alternate devices)

shanghai meng Yan Automation Equipment Co. http://www.monsun.cn

prior to installation check regulator controller has no collision injury, loose

screw, and
wireless off. If there is significant damage, please contact the home and produc
tion.

shanghai meng Yan Automation Equipment Company Limited http://www.monsun.cn

MS3000 Contents Chapter 1 Basic Series ..................... ...................
.. 6
I. INTRODUCTION ............................................ II. features ......
................................. 6 6 III. ...... Theory of ....................
..... ................... 7 4. The range of application 8 5 .EDI ...............
............ .... power system application block diagram . . . . 8
Chapter 2 Technical Specifications . . . . . .
. 9 ............ ..... ........ ............ 9 Naming Model 2. Specification ...
...................................... 9 3. Install.... Requirements for Using .
........................ 10 4. The appearance... and Mounting Dimensions .......
.................................................................... 10.
Chapter 3 wiring instructions
. . . . . . . . . . . . the control circuit board terminals figure and Descripti
on . . . . . . . . . . . 12 2. The terminal 13 III. :..........................
instructions control potentiometer board and pull the switch descriptions of ...
............. 14 4. The panel LED descriptions 14 .............. ...............
.. v. user wiring instructions ... .............. 15.
Chapter 4 Installing the Debugging steps ....... .................. 15
I. debugging, run a program .. 15 4. The ....................... light load lab.
............................... 16 V. troubleshooting ..........................
........... 16
Chapter 5 Notice to oeders....................................... 18

shanghai meng Yan Automation Equipment Co. http://www.monsun.cn

MS1000 Chapter 1 Basic Series . . . . . . . 20
1. Introduction ....................................... 20 ....... ........ ....
... ........ ....... ....... ....... features 2. 20 III. theory.................
...........21 .... IV Application Scope................... 22
Chapter II SPECIFICATIONS.............22
a.Model... named ....................................... . . . . . 22 2. Specifi
cation ......................... 23 ..... 3. installation use requirements .....
............................. 23 4. installation use requirements ..............
.................... 23 V. shape and mounting size..........................24
Chapter 3 wiring instructions................ 25
I. control board terminals figure and a description of the work of the session..
................................ 25 II. Terminal Description :..................
.... 26 3. The.... Test Point Description . . . . 4 27 ...... panel LED descript
ions..........................27 V. user wiring instructions....................
.................. ...... 27
Chapter 4 Installing the Debugging steps . . . . . . . . . . . . 28
I. debugging, run a program 28 II........................... light load lab . .
. . . . . . . . . 29 3. troubleshooting ........................................
. 30
Chapter 5 Notice to oeders ..................... .....................

Shanghai economic benefit 30 Automatic Equipment Co. http://www.monsun.cn

MS3000
MS3000 Series Series Voltage adjustment range of current,0-10A, :0-500VDC E-CELL
,IONPURE,ELECTROPRE applies to import such as high flow module, as well as a var
iety of homemade high flow module. Constant voltage or constant current mode can
be to select. This product can be widely used for ultra-pure water industrial f
ields.

shanghai meng Yan Automation Equipment Co. http://www.monsun.cn

rationale chap.
I. INTRODUCTION:
MS3000 series dc pressure unit is a compact wall mounted constant pressure, cons
tant
-current analog control Regulator Controller, the unit in absorbing the Siemens
company dc load placed on the basis of the Company by the self-developed product
s. The unit has a small, compact structure, easy to install, easy to debug a wid
e range of pressure, anti-dry nuisance capability, Good linearity of the output,
the protection of the safe operation of the agile movements, features. Can be w
idely used in water treatment module (EDI,CEDI modules such as the pressure adju
st) flow areas serving as the dc voltage power usage.
This unit has the following characteristics:
1, compact design.
2, easy to use and easy to debug.
3, L, buck buffer.
4, master control circuit with the Siemens company technology.
5, controllable silicon module uses the famous international company product war
ranties that the craft and high reliability.
6, with soft-start off, Constant current or constant voltage operation; over-cur
rent, over-temperature protection. Current-limit capability can be effectively p
rotected power body and reduce the negative impact of the.
2. Features:
MS3000 DC pressure unit used phase firing method to achieve voltage stepless reg
ulating, to achieve the purpose of the power control. Enter the three-phase 380V
AC.
The adjustment range of the output voltage is rather wide, are normally
0-500VDC rated output voltage. With soft-start, soft-off, Constant Current, Curr
ent-limit, overcurrent protection,
thermal overload protection features.

shanghai meng Yan Automation Equipment Co. http://www.monsun.cn

1. Soft-start, soft shutdown functions: soft-start, soft-off is a
power supply or a given voltage, drastic changes in the output is not
changed dramatically. Soft-start soft shutdown to make the output smoothly chang
ing.
2. Constant Current Features: When using current feedback, if given letter numbe
rs do not change, even if the load over the ambient temperature changes, output
current
at rated current at any point within the scope have been able to meet the object
ives of the constant current
.
3. Current-limit capability: The user can control board on the potentiometer set
ting
maximum operating current.
4. overcurrent protection feature: When working with more than the nominal curre
nt peaks UNIDO as current, voltage regulator controller will quickly output sour
ce switch signal to control external circuitry. The external circuit shuts off t
he output of protection of the equipment.
5. Thermal Overload Protection Features: when the ambient temperature is high, p
ose heat temperature over 85C, the regulator will output rate control voltage-fre
e switch signal to control external circuitry. When the heat sink temperature be
low 80C, will automatically resume output. The external circuit shuts off the out
put of protection of the equipment.
3. Principle :
The unit from the main part of the circuit and control regulating circuit compon
ents.
1. The main loop section:
main circuit consists of six import thyristor composition of three-phase half co
ntrolled bridge is not reversible
circuit, controllable silicon trigger pulses of Phase Shift To adjust the output
voltage. The controllable silicon trigger pulse phase by the control section to
determine the scope of its phase shift of about 0 ~ 150 ms.
2. Adjust controls section:
control and regulation of the signal by the blockade, given points, the current
regulator,
triggers, current negative feedback, overcurrent protection. Its function is to
direct

shanghai meng Yan Automation Equipment Co. http://www.monsun.cn

flow regulator in load change, temperature changes and the voltage change
the stability of a pre-a given value.
Signal Chain:
In X1:2 embargo imposed by the end of the "B" enter a +24V (with "X1:1 level P24
is switched on), the operation LED is lit, and given points, voltage regulator
and current regulator electronic switch is open, the
Trigger Phase Shift lifting of the blockade, pressure-regulating devices to work
ing status.
[Note]! ! ! The port of the device could be X1:2 start or will not start, but wh
en the +24V input end is X1:2 level, relying only on the power on and off
to start and stop the unit is not a good method of operation, sometimes such par
ty
law in power off the half cycle that may arise within the uncontrolled current p
ulse
manually, the main contacts beat, cause unwanted load runout and load shift or d
amage to the unit! ! !
4. Applications:
MS3000 DC pressure unit is designed specifically for use in the water treatment
industry ultra-pure water systems and other CEDI EDI, water treatment module fea
tures designed to support the power supply. Therefore, the product can be widely
used for ultra-pure water industrial fields.
5 Power System Application box .EDI figure:
one-to-one system:

8 with one
of yan automation equipment Shanghai Co. http://www.monsun.cn
MS3000 1# pure water supply 0-500VDCEDI Module 1
fuses (3) Fuse (1) a
pure water supply 2# MS3000 0-500VDCEDI Module 2
fuses (3) Fuse (1)
# pure water supply MS3000 0-500VDCEDI Module 3
fuses (3) Fuse (1)
MS3000 main switch keywords with pure water supply
0-500VDCEDI module N three phase 380VAC 3-Phase 380V fuse (3) Fuse (1)
running the control
program fence feedback
water run N rectifier signal control circuit of the
programd start/stop alarm rectifier off water signal
to go on site or remote control cabinet
chapter II, technical specifications
, model and a sense:
for example of rated output voltage :MS3010A 500VDC, 10A rated output current th
ree-phase DC unit.
2, Specification:
1. control and regulating circuits 3&~380vac: 10%/45~65HZ input supply voltag
e: Output Voltage Range: DC 0~500V(DC 0~600V need to do) Output current range: D
C 0~10A(10A above need to be done so) input control signal voltage input to the
control input, current control Dc0~-10v
Dc0~+10v

shanghai meng Yan Automation Equipment Co. http://www.monsun.cn

Applicable Load: EDI, CEDI module, as well as other ultra-pure water Module Powe
r Consumption: no load approximately 10W overload capacity: 150 percent of rated
current, time is less than 30 seconds to adjust the current: 0~100% linear set
overcurrent protection: 80~150% adjustable startup, shutdown mode: soft-start, s
oft-off mode: The modular structure working methods: cooling: natural cooling 3,
Installation Requirements:
a, the unit should be mounted vertically in the 3 chassis or on the frame of the
machine to the cooling
air flow of the bottom-up and that the power of the natural terminal toward the
bottom.
The next speaker unit b, must ensure that there is a gap of 50mm, in order to en
sure that the cooling air does not affect
the access to and from the air. The thermal plate and chassis mounting plate bet
ween must ensure that
there is a gap of 15mm, so that the air circulation.
Iv. conditions of use:
1. Ambient Temperature: 0C~+40C 2. Storing Temperature: -10C~+85C temperature rating
of 3. 4. Protection Rating: FMEY IP00: 5. Altitude: 1000 m (100 m above sea lev
el rise, rating fell 1 per cent).
5, Overall dimensions and Installation Instructions:
1) Dimensions:

10
shanghai meng Yan Automation Equipment Co. http://www.monsun.cn
230 70
ultra-pure water supply
205 MS3000
Current Feedback
IF
overcurrent protection OVER THE CURR
MAXIMUM CURRENT
IMAX
zero
ZERO SET
JP3) power SHORTED cyclic JP2 decapsulates the directive of the power supply thr
ee phase input dc output Three Phase Controllers Power conditioning input 1 to a
djust input 2 DS1 DS2 DS3 1 S1 2S2 3T2T2 41C1C 51D1D 62D2D S2 SHORTED R1R1 S1S1
T1T1
decapsulation 1 2
3
N10N10 P24P24 BB 4
5
MM 6
P10 UU P10 7
II 8
MM
power fault 9 10
NO NO PP V Constant Voltage Constant Current I DS1 DS2, DS
1
R2
JP3R2 JP2 JP1 I V
2) control circuit board terminals figure and description:
JP3) power SHORTED cyclic JP2 decapsulates the directive of the power supply thr
ee phase input dc output Three Phase Controllers Power conditioning input 1 to a
djust input 2 DS1 DS2 DS3
S1 1
R2 S22 1C4 1D5 2D6 T23 R1 S1 T1
decapsulates
P241 N103 2 B U4 M5 P106 I7 8M constant current I V constant voltage
power supply fault NO9 10P three phase input dc output Three Phase Controllers P
ower conditioning input 1 to adjust input 2-seal failure

11

Yan automation equipment of Shanghai Co. http://www.monsun.cn

Chapter 3 wiring instructions
first, Terminals Description: [Note]! ! ! If a connection is not correct, the
unit may be damaged! !
1) Primary circuit:
Features Terminal Number Description Notes
R2 phase line
S2 phase power input terminals T2 line
1C (D+) positive
voltage output of 1D (D-) Negative 2) control circuit: Adjust the
Terminal Number feature label instructions -JP1:1 +24VDC Power Supply P24 to pre
vent shorting
-JP1:2 Unit On / Off Floppy B input level,
switch to +24VDC start to working status;
level, the unit is turned off and not done.
The power supply OPERATES JUST -JP1:3 N10 to prevent shorting

of Hin Shanghai 12 Automatic Equipment Co. http://www.monsun.cn

-JP1:4 given value 1 U 0~-10VDC, with ramp occurred
.
Boost, Buck2 L2 in time.
The reference to M -JP1:6 -JP1:5 +10VDV power P10 to prevent shorting -JP1:7 giv
en value 2 I M -JP1:9 -JP1:8 reference temperature, over current alarm NO switch
output
reference to P
ii -JP1:10, Selector Switches, Potentiometers feature descriptions in the table
below:
Code Label Feature Description
S1 S1 constant current/constant voltage select on the left side of the dial to I
unit
is a constant current system; the right to the side of the unit
for V constant voltage systems.
For details, see the Theory of Operation section.
Adjust the amount of current feedback IF adjust adjustment 70~130%; clockwise,
anti-clockwise.
[Note] adjustment will affect the
unit adjust the maximum output current.

13

yan automation equipment of Shanghai Co. http://www.monsun.cn

46 OVER CURR. overcurrent protection for the small clockwise, counter-clockwise.
62 Max current imax value small clockwise, counter-clockwise.
Set the
unit SET output R108 ZERO zero position adjustable large clockwise, counter-cloc
kwise.
Section
III. test point parameters:
Code Label Measurements Instructions -JP1:1 +24VDC power supply, P24 static valu
es -JP1:3 N10 OPERATES JUST power, static values LIKE the power, P10 -JP1:6 stat
ic values -JP1:5 M 0VDC -JP1:8 M 0VDC Reference Reference Points V1 0~-10VDC dyn
amic value, depending on the size of the load current
test point 0~10VDC V2 dynamic value, depending on the size of the output voltage
4 Panel Indicator Description:
device panel has three LED DS1, DS2, DS3 its features are
n DS1 enable indicator lights, indicating the pressure regulator Controller Star
tup is in working condition.
N DS2 Phase sequence indicator lights, indicating the pressure regulator control
ler in the electrical
supply phases sequence error, transfer any two of the phase sequence, phase sequ
ence lights off, Voltage Regulator Controller to function.
N Power LED DS3 This lamp is lit, indicating the pressure regulator controller i
s in a power-saving state.

14

yan automation equipment of Shanghai Co.

v. users http://www.monsun.cn Wiring Instructions:
1. Connect the main circuit R2, S2, T2, 1C, 1D. The main circuit withstand all t
he current negative R2, S2, T2 as power supply in the Access User level before,
power distribution units, such as the air switch, fuses etc. 1C, 1D user access.
(recommendation rear access fuse before the access load) 2. Connect the control
potentiometer. Connection control N10,u,m potentiometer 1,P10, A,m connection c
ontrol potentiometer 2 generally used).
3. Enable the connection. When the connection phase shift P24,b trigger were lif
ting of the blockade, the
pressure regulator controller to working status.
4. Connect the alarm signal control cable. When an overcurrent when the pressure
regulator controller alarm output, free contacts are available for the user ext
ernal alarm circuit, contact capacity maximum 220VAC/1A. Terminal with NO P for
alarm output normally open contacts.
Chapter 4 Installing the Debugging Step
1. Debugging, run a program:
1. The unit before the Terminal, please check for the load.
(1) Load on the nameplate voltage, current and voltage regulator is unit; (2) th
e load on a match no shorts; (3) load, and insulated with the EARTH INSULATION.
2. Check the supply voltage of the unit, such as whether there was a match does
not match the device will be damaged!
3. It is important to ensure that the terminal wiring is correct! ! !
1) Power Supply Output Voltage Input loop circuit of the importance of the inter
action between conductors insulated, and there are conductor insulated with the
earth, otherwise the unit will be damaged bad!
2) control signal leads to avoid close to power cables and strong electric circu
it of the import

of 15 Shanghai Xin automation equipment co.

, preferably in a http://www.monsun.cn shield wire, it may cause damage to the u
nit!
3) Power Supply cable entry side must be installed quickly fuse, fuse rated
load current 1.2~1.5 times.
4. Check that the unit on the select switch S1 is allocated at the appropriate l
ocation.
1) select S1 V side, devices for the continuous pressure system.
2) S1 Select I side, unit a constant current system.
5. Check the phase sequence.
After the power-on indicator lights up phase sequence DS2 0.3 seconds off of a t
hree-phase phase sequence properly; if the DS2 is illuminated after the fight of
the three-phase power, phase sequence not to switch off power in three phase R2
, S2, T2 2-phase of any.
6. Output Zeroing (factory adjusted).
7. Maximum Output Current adjustment has been adjusted at the factory: (1) Regul
ate) potentiometer R47(imax) to minimum; 2) Close the main power, the main cause
of the potentiometer to a maximum;3) gradually adjust the potentiometer R47(ima
x), until the current table indicates the value of
the load to desired rated current.
2. The light load test:
connecting power controller, disconnect the power cord from the input power cont
roller and
the wiring, only three of the bulb (lamp incandescent 100W/220V power shall not
be less than the load of false 40W) three light bulb is series connection to pow
er control, respectively, for the output terminals. Open the power controller an
d the control panel circuit board at the toggle switch S1 to the constant pressu
re. Switch on the power supply, do the following checks.
Adjust the potentiometer input (input potentiometer to P10, V, M), gradually fro
m a small to a large scale adjustment potentiometer input, output voltage rise l
inearly, an output voltage of the rating.
These faults press troubleshooting methods to troubleshoot the problem.

16

yan automation equipment of Shanghai Co. http://www.monsun.cn

3. Troubleshooting
Serial Number: The cause for the failure symptoms processing method 1 after powe
r on the main power, power is incorrect, and the phase of three-phase shift in e
ither the
primary signal, load quick-melt blown or synchronize to a two-phase, when voltag
e is present. The DS2 is illuminated transformer. Swap the fuse or synchronize t
ransformer.
2 Power on the system to the primary signal 1) End Users 1 X1:2(b) access +24VDC
level.
After the load has no voltage. There are Input +24VDC2) check primary loop.
Level. 3) Press 2 to check.
2) circuit voltage output
.
3) control power and the main
phase of the power source
step different
3 output voltage is low ,1) rectifier bridge output 1) Check the trigger wire co
nnections are
not rated for a maximum load of the waveform is missing. Good.
The value. 2) given the voltage offset 2 ) measurement is
low. X1:5(u) The OPERATES JUST.
3) Current Limiter for 3) Adjust the potentiometer
. R47(imax).
4 overcurrent protection relay 1) load current is too large. 1) Check the load,
troubleshooting.
K. 2) Overcurrent Protection Links 2) to check the protection aspects of trouble
shooting
. Failure.
5 Fast fuse blown. 1) load current inspection of the load and the main loop to e
xclude
. Failure.
2) Output Loop with short

17

Yan automation equipment of Shanghai Co. http://www.monsun.cn

road.
3) controllable silicon module from
bad.
6 Voltmeter voltage display voltmeter to swap or direct voltage anti-table indir
ect negative values or wireless stream output port is open. On the load.

Chapter 5 The order to know

when ordering the user shall specify:
1. rated input voltage, frequency 2. The rated operational current

Thank you read the instructions for use! ! !

The unit is part of the input, output and strong, operating safely when! !

18

yan automation equipment of Shanghai Co. http://www.monsun.cn

MS1000
MS1000 Series Series Voltage adjustment range :0-340VDC 0-200VDC, or current
0-10A, E-CELL,IONPURE,ELECTROPRE applicable import such as high flow template bl
ock, as well as a variety of homemade high flow module. Constant voltage or cons
tant current mode can be selected.
This product can be widely used for ultra-pure water industrial fields.

19

yan automation equipment of Shanghai Co. http://www.monsun.cn

rationale chap.
I. INTRODUCTION:
MS1000 series dc pressure unit is a compact wall mounted constant pressure, cons
tant
-current analog control Regulator Controller, the unit in absorbing the Siemens
company dc load placed on the basis of the Company by the self-developed product
s. The unit has a small, compact structure, easy to install, easy to debug a wid
e range of pressure, anti-dry nuisance capability, Good linearity of the output,
the protection of the safe operation of the agile movements, features. Can be w
idely used in water treatment module (EDI,CEDI modules such as the pressure adju
st) flow areas serving as the dc voltage power usage.
This unit has the following characteristics:
1, compact design.
2, easy to use and easy to debug.
3, L, buck buffer.
4, master control circuit with the Siemens company technology.
5, controllable silicon module uses the famous international company product war
ranties that the craft and high reliability.
6, with soft-start off, Constant current or constant voltage operation; over-cur
rent, over-temperature protection. Current-limit capability can be effectively p
rotected power body and reduce the negative impact of the.
2. Features:
MS1000 DC pressure unit used phase firing method to achieve voltage stepless reg
ulating, to achieve the purpose of the power control. 1, input voltage single ph
ase 220VAC, output voltage the adjustment range of the rather wide, are normally
0-200VDC rated output voltage. 2, 2 phase input voltage output voltage regulati
on 380VAC, section within a wide, are normally 0-340VDC rated output voltage. Wi
th soft

20

Yan automation equipment of Shanghai Co. http://www.monsun.cn

launch, soft-off, Constant Current, Current-limit, overcurrent protection, therm
al overload protection features.
6. Soft-start, soft shutdown functions: soft-start, soft-off is a
power supply or a given voltage, drastic changes in the output is not
changed dramatically. Soft-start soft shutdown to make the output smoothly chang
ing.
7. Constant Current Features: When using current feedback, if given letter numbe
rs do not change, even if the load over the ambient temperature changes, output
current
at rated current at any point within the scope have been able to meet the object
ives of the constant current
.
8. Current-limit capability: The user can control board on the potentiometer set
ting maximum
operating current.
9. overcurrent protection feature: When working with more than the nominal curre
nt peaks UNIDO as current, voltage regulator controller will quickly output sour
ce switch signal to control external circuitry. The external circuit shuts off t
he output of protection of the equipment.
10. The overheat protection: when the ambient temperature is high, pose heat tem
perature over 85C, the regulator will output rate control voltage-free switch sig
nal to control external circuitry. When the heat sink temperature below 80C, will
automatically resume output. The external circuit shuts off the output of prote
ction of the equipment.
3. Principle :
The unit from the main part of the circuit and control regulating circuit compon
ents.
1. The main loop section:
main circuit consists of 4 import thyristor composition of single phase half con
trolled bridge is not reversible Electric Road, through the controllable silicon
trigger pulses of Phase Shift To adjust the output pressure change. The control
lable silicon trigger pulse phase adjust controls part of the defined and its ph
ase shift range of about 0 ~ 150 ms.
2. Adjust controls section:
control and regulation of the signal by the blockade, given points, the current
regulator,

21

shanghai meng Yan Automation Equipment Co. http://www.monsun.cn

triggers, current negative feedback, overcurrent protection. Its function is to
direct flow regulator in load change, temperature changes and the voltage change
the stability of a pre-a given value.
Signal Chain:
In X1:2 embargo imposed by the end of the "B" enter a +24V (with "X1:1 level P24
is switched on), the operation LED is lit, and given points, voltage regulator
and current regulator electronic switch is open, the
Trigger Phase Shift lifting of the blockade, pressure-regulating devices to work
ing status.
[Note]! ! ! The port of the device could be X1:2 start or will not start, but wh
en the +24V input end is X1:2 level, relying only on the power on and off
to start and stop the unit is not a good method of operation, sometimes such par
ty
law in power off the half cycle that may arise within the uncontrolled current p
ulse
manually, the main contacts beat, cause unwanted load runout and load shift or d
amage to the unit! ! !
4. Applications:
MS1000 DC pressure unit is designed specifically for use in the water treatment
industry ultra-pure water systems and other CEDI EDI, water treatment module fea
tures designed to support the power supply. Therefore, the product can be widely
used for ultra-pure water industrial fields.
Chapter II, technical specifications
, model and a sense:
for example for the Rated Input :380VAC :MS1010A. Rated output voltage 340VDC, r
ated output current of 10A single-phase DC units. The Rated Input: MS1010B
220VAC. Rated output voltage 200VDC, 10A rated output current single-phase flow
direct unit.

22

yan automation equipment of Shanghai Co. http://www.monsun.cn

II. Specification:
1. control and regulating circuits:
input power voltage: kill ~380vac or 1 & ~220vac
/45~65HZ 10% output voltage range: DC 0~340V(DC 0~200V) output current range: DC
0~10A(10A above need to be done so) input control signal voltage input to the co
ntrol input, current control Dc0~-10v
Dc0~+10v
Applicable Load: EDI, CEDI module, as well as other ultra-pure water Module Powe
r Consumption: no load approximately 10W overload capacity: 150 percent of rated
current, time is less than 30 seconds to adjust the current: 0~100% linear set
overcurrent protection: 80~150% adjustable startup, shutdown mode: soft-start, s
oft-off mode: The modular structure working methods: cooling: natural cooling 3,
Installation Requirements:
a, the unit should be mounted vertically in the 3 chassis or on the frame of the
machine to the cooling
air flow of the bottom-up and that the power of the natural terminal toward the
bottom.
The next speaker unit b, must ensure that there is a gap of 50mm, in order to en
sure that the cooling air does not affect
the access to and from the air. The thermal plate and chassis mounting plate bet
ween must ensure that
there is a gap of 15mm, so that the air circulation.
Iv. conditions of use:
1. Ambient Temperature: 0

23C

Shanghai C~+40 of Yan Automation Equipment Co. http://www.monsun.cn

2. Storing Temperature: -10C~+85C temperature rating of 3. 4. Protection Rating: F
MEY IP00: 5. Altitude: 1000 m (100 m above sea level rise, rating fell 1 per cen
t).
5, Overall dimensions and Installation Instructions:
1) Dimensions:
186
ultra-pure water treatment power 70
MS1000 182
zero
ZERO SET
overcurrent protection
OVER THE CURR
Maximum Current JP3 JP2 IMAX
Phase Sequence power regulation Power Input 1 to adjust input 2 VDC output ac in
put 1 S1 decapsulates the DS1 DS2 Hang Stream indicates I constant pressure
to release 1 2 V P24 B 3 N10 4U 5M 6P10 7I 8M 1N 41U
1C+ 21C+ 3 1N DS1 S 1 JP3
Power Supply Fault 9 10 NOP 1D-
1D- DS2I JP1 V3 5 6 8 JP2 164.0000 6 5
2) Control Circuit Board Terminal Diagram and description:

24

of yan automation equipment Shanghai Co. http://www.monsun.cn

JP3
power supply of the JP2 orderly adjustment of Input 1 to adjust input 2 VDC outp
ut AC Input S1 decapsulates the constant pressure 1 Indicates constant current
D S 1 D S 2 I V
-seal 1
P24 2 B 3
N10 4
U 5
M 6
P10 7
I 8
M
Power Fault 9 10
N O P 1D- 2
3
1N4,
1U 1C+
Power Power conditioning input 1 to adjust input 2 VDC output phase two 380V inp
ut-seal faulty
wiring instructions Chapter III
A, Terminals Description: [Note]! ! ! If a connection is not correct, the
unit may be damaged! !
1) Primary circuit:
Features Terminal Number Description notes the input side of the power of 1U pha
se MS1010A :380VAC rated input.
1N 340VDC rated output voltage.
The phase conductor of the Rated Input :220VAC MS1010B.
Voltage Output Port 1C (D+) positive 200VDC rated output voltage.
1D (D-) Negative
2) control circuit: Adjust the
Terminal Number feature label instructions -JP1:1 +24VDC Power Supply P24 to pre
vent shorting

of Hin Shanghai 25 Automatic Equipment Co. http://www.monsun.cn

-JP1:2 unit start/B Input Level, the unit started +24VDC input
into the work of the soft switch off status; 0 level, the unit is turned off
does not work.
The power supply OPERATES JUST -JP1:3 N10 to prevent shorting -JP1:4 values are
given in the 1-U 0~-10VDC, beveled wave generator.
Boost, Buck2 L2 in time.
The reference to M -JP1:6 -JP1:5 +10VDV power P10 to prevent shorting -JP1:7 giv
en value 2 I M
-JP1:9 -JP1:8 reference temperature, overcurrent reported NO switch output
warning reference P
ii -JP1:10, Selector Switches, Potentiometers feature descriptions in the table
below:
Code Label Feature Description S1 S1 constant current/constant voltage options l
eft to the side of the unit for I hang stream is
optional switch and to the Right; Side, devices for the V constant
voltage systems.
For details, see the Theory of Operation section.
R81 OVER THE CURR. overcurrent protection value clockwise small, counter-clockwi
se.
The
shanghai economic benefit 26 Automatic Equipment Co. http://www.monsun.cn
R79 imax unit maximum current clockwise small, counter-clockwise.
Set the value
ZERO SET unit output R77 zero position clockwise, counter-clockwise.
Adjust the
various test points parameters:
Code Label Measurements Instructions -JP3:1 +24VDC power supply, P24 static valu
es -JP3:3 N10 OPERATES JUST power, static values LIKE the power, P10 -JP3:6 stat
ic values -JP3:5 M 0VDC -JP3:8 M 0VDC reference reference to four, Panel Indicat
or Description:
device panel has three LED DS1, DS2, its functions are
n DS1 enable indicator lights, indicating the pressure regulator Controller Star
tup is in working condition.
N Power LED DS2, this lamp is lit, indicating the pressure regulator controller
is in a power-saving state.
5, User Wiring Instructions:
1. Connect the main circuit 1U, 1N, 1C+, 1D. The main circuit load full of curre
nt. 1U, 1N as the line of power supply in a user level before the power distribu
tion unit, such as air switch, fuses etc. Access, 1D 1C+ user load. (recommendat
ion
rear access fuse before the access load)
2. Connect the control potentiometer. Connection control N10,u,m potentiometer 1
,P10, A,m connection control potentiometer 2 generally used).

27

yan automation equipment of Shanghai Co. http://www.monsun.cn

3. Enable the connection. When the connection phase shift P24,b trigger were lif
ting of the blockade, the
pressure regulator controller to working status.
4. Connect the alarm signal control cable. When an overcurrent when the pressure
regulator controller alarm output, free contacts are available for the user ext
ernal alarm circuit, contact capacity maximum 220VAC/1A. Terminal with NO P for
alarm output normally open contacts.
Chapter 4 Installing the Debugging Step
1. Debugging, run a program:
1. The unit before the Terminal, please check for the load.
(1) Load on the nameplate voltage, current and voltage regulator is unit; (2) th
e load on a match no shorts; (3) load, and insulated with the EARTH INSULATION.
2. Check the supply voltage of the unit, such as whether there was a match does
not match the device will be damaged!
3. It is important to ensure that the terminal wiring is correct! ! !
1) Power Supply Output Voltage Input loop circuit of the importance of the inter
action between conductors insulated, and there are conductor insulated with the
earth, otherwise the unit will be damaged bad!
2) control signal leads to avoid close to power cables and strong electric circu
it line, it is preferable to use import shield wire, it may cause damage to the
unit!
3) Power Supply cable entry side must be installed quickly fuse, fuse rated
load current 1.2~1.5 times.
4. Check that the unit on the select switch S1 is allocated at the appropriate l
ocation.
1) select S1 V side, devices for the continuous pressure system.
2) S1 Select I side, unit a constant current system.
5. Output Zeroing (factory adjusted).

28

yan automation equipment of Shanghai Co. http://www.monsun.cn

6. Maximum Output Current adjustment has been adjusted at the factory: (1) Regul
ate) potentiometer R79(imax) to minimum; 2) Close the main power, the main cause
of the potentiometer to a maximum;3) gradually adjust the potentiometer R79(ima
x), until the current table indicates the value of
the load to desired rated current.
2. The light load test:
connecting power controller, disconnect the power cord from the input power cont
roller and
the wiring, only three of the bulb (lamp incandescent 100W/220V power shall not
be less than the load of false 40W) three light bulb is series connection to pow
er control, respectively, for the output terminals. Open the power controller an
d the control panel circuit board at the toggle switch S1 to the constant pressu
re. Switch on the power supply, do the following checks.
Adjust the potentiometer input (input potentiometer to P10, V, M), gradually fro
m a small to a large scale adjustment potentiometer input, output voltage rise l
inearly, an output voltage of the rating.
These faults press troubleshooting methods to troubleshoot the problem.
3. Troubleshooting
Serial Number: The cause for the failure symptoms approach 1 Power on the system
to the primary signaling port not 1 X1:2(b) 1) Access Level +24VDC
After you enter the number of load without input +24VDC2) check primary loop.
Voltage. Level.
2) circuit voltage output
.
2 output voltage is 1) Rectifier Bridge Output Wave 1) Check the trigger wire co
nnection is
low, and the loads of up to not-missing. Good.
The rating. 2) given the voltage offset 2 ) measurement is up to

29

Shanghai X1:5(u) of Yan Automation Equipment Co. http://www.monsun.cn

low. The OPERATES JUST.
3) Current Limiter for 3) Adjust the potentiometer
. R79(imax).
3 overcurrent protection relay 1) load current is too large. 1) Check the load,
troubleshooting.
For K. 2) Overcurrent Protection Links 2) to check the protection aspects of tro
ubleshooting
. Failure.
4 Fast fuse blown. 1) load current inspection of the load and the main loop to e
xclude
. Failure.
2) Output Loop with short
circuit.
3) controllable silicon module from
bad.
5 Voltmeter voltage voltmeter to the video or Direct Transfer of Anti-voltage ta
ble shown in line or to indirect negative value stream output port is open. On t
he load.
Chapter 5 The order to know
when ordering the user shall specify:
3. rated input voltage, frequency 4. The rated operational current
Thank you read the instructions for use! ! !
The unit is part of the input, output and strong, operating safely when! ! !

30