PERFORMANCE SPECIFICATION 2

PERFORMANCE SPECIFICATION 2
Contents

1. GENERAL 1

2. CHARACTERISTIC ENERGISING QUANTITY 1

3. CHARACTERISTICS 1
3.1. Operating Characteristics 1
3.2. Overcurrent Settings 1
3.3. Operating Times 1

4. ACCURACY REFERENCE CONDITIONS 2

5. ACCURACY 2

6. ACCURACY GENERAL 2

7. ACCURACY INFLUENCING QUANTITIES 2

8. THERMAL WITHSTAND 2

9. BURDENS 2

10. OUTPUT CONTACTS 2

11. ENVIRONMENTAL WITHSTAND 3

FIGURE 1 2TJM10 IDMTL CHARACTERISTICS, 50Hz 4

FIGURE 2 2TJM20 IDMTL CHARACTERISTICS, 50Hz 5
FIGURE 3 2TJM30 IDMTL CHARACTERISTICS, 50Hz 6
FIGURE 4 2TJM60 IDMTL CHARACTERISTICS, 50Hz 7
FIGURE 5 2TJM70 IDMTL CHARACTERISTICS, 50Hz 8
FIGURE 6 2TJM10 IDMTL CHARACTERISTICS, 60Hz 9
FIGURE 7 2TJM20 IDMTL CHARACTERISTICS, 60Hz 9
FIGURE 8 2TJM30 IDMTL CHARACTERISTICS, 60Hz 10
FIGURE 9 2TJM70 IDMTL CHARACTERISTICS, 60Hz 10
FIGURE 10 OPERATING CHARACTERISTIC OF
DIRECTIONAL ELEMENT 11
FIGURE 11 DIRECTIONAL CURRENT/PHASE ANGLE
CHARACTERISTIC 11
FIGURE 12 2TJM10/70 IMPEDANCE/CURRENT
CHARACTERISTIC, 1A RELAY, 50Hz 12
FIGURE 13 2TJM10/70 IMPEDANCE/CURRENT
CHARACTERISTIC, 5A RELAY, 50Hz 12
FIGURE I4 2TJM20 IMPEDANCE/CURRENT
CHARACTERISTIC, 1A RELAY, 50Hz 13
FIGURE 15 2TJM20 IMPEDANCE/CURRENT
CHARACTERISTIC, 5A RELAY, 50Hz 13
FIGURE 16 2TJM30 IMPEDANCE/CURRENT
CHARACTERISTIC, 1A RELAY, 50Hz 14
FIGURE 17 2TJM30 IMPEDANCE/CURRENT
CHARACTERISTIC, 5A RELAY, 50Hz 14
FIGURE 18 2TJM60 IMPEDANCE/CURRENT
CHARACTERISTIC, 1A RELAY, 50Hz 15
FIGURE 19 2TJM60 IMPEDANCE/CURRENT
CHARACTERISTIC, 5A RELAY, 50Hz 16
 PERFORMANCE SPECIFICATION 2
1. GENERAL IDMT - 2TJM60 Range
Setting Range Step (A) Rating In (A)
Performance Data to IEC 255 0.05 - 0.2 0.025 1
0.1 - 0.4 0.05 1 2
2. CHARACTERISTIC ENERGIZING QUANTITY 0.2 - 0.8 0.1 1 2
0.4 - 1.6 0.2 2
Range AC Current in 0.5 - 2 0.25 5
2TJM10 0.5A, 1A, 2A or 5A 1-4 0.5 5
2TJM20 1A or 5A
2TJM30 1A or 5A
2TJM60 1A, 2A or 5A
2TJM70 1A or 5A IDMT - 2TJM13, 2TJM73 Ranges
2TJM13 & 2TJM73 1A or 5A Setting Range Step (A) Rating In (A)
0.2 - 0.8 0.1 1
Directional Element 0.5 - 2 0.25 1
Overcurrent, Vn 110V 1-4 0.5 5
Earth fault, Vn 63.5V or 110V 2.5 - 10 1.25 5
Current, Is 0.5A, 1A, 2A or 5A

Earth fault current and voltage coils need to be residually Highset Element Setting Ranges
connected. For voltage this will require a five limb voltage Rating 1A Rating 2A Rating 5A
transformer with an open delta tertiary winding, alternatively 3 0.4 - 1.6A 2 - 8A
single phase interposing transformers may prove suitable. 2 - 8A 10 - 40A
4 - 16A* 8 - 32A 20 -80A*
Frequency 50 or 60Hz 8 - 32A* 40 - 160A*
10 - 40A* 50 - 200A*

3. CHARACTERISTICS *the only ranges on 2TJM14 and 2TJM74 ranges

3.1 Operating Characteristics

Directional Element Settings
Range Characteristic Overcurrent 15% of IDMT nominal current rating
2TJM10 Normal inverse form 3/10 IDMT at the maximum torque angle of 45 lead.
2TJM20 Very inverse IDMT Earth fault 7.5% of IDMT nominal current rating at
2TJM30 Extremely inverse IDMT the maximum torque angle of 12.5 lag.
2TJM60 Long time inverse form 5/30 IDMT
2TJM70 Normal inverse form 1.3/10 IDMT
3.3 Operating Times

3.2 Overcurrent Settings IDMT Operate times can be calculated as follows:

IDMT - 2TJM10 Range Refer to curves for 50Hz and 60Hz

Setting Range Step (A) Rating In (A)
0.05 - 0.2 0.025 0.5 1 Time multiplier 0.1 to 1.0 0.05
0.1 - 0.4 0.05 0.5 1 2 Highset 20ms at 2 x setting
0.2 - 0.8 0.1 1 2 12ms at 5 x setting
0.25 - 1 0.125 5 Directional 100ms
0.4 - 1.6 0.2 2
0.5 - 2 0.25 1 5
1-4 0.5 2 5
2.5 - 10 1.25 5

IDMT - 2TJM20, 2TJM30, 2TJM70 Ranges

Setting Range Step (A) Rating In (A)
0.1 - 0.4 0.05 1
0.2 - 0.8 0.1 1
0.5 - 2 0.25 1 5
1-4 0.5 5
2.5 - 10 1.25 5

1
2 PERFORMANCE SPECIFICATION

Range Pick-up Reset Typical reset

time* Frequency
2TJM10 not >130% not <95% 14s Range 47Hz to 51 Hz
of Is of Is 56Hz to 62Hz
2TJM20 not >130% not <90% 30s Operating time +9% to -4%
of Is of Is variation at reference +12% to -6.5% for 2TJM60
2TJM30 not >130% not <90% 35s frequency
of Is of Is
2TJM60 not >110% not <60% 70s
of Is of Is 8. THERMAL WITHSTAND
2TJM70 not >130% not <90% 6s
of Is of Is Continuous Overload
2TJM13 & not >130% not <95% 14s IDMT element 2.0 x Is
2TJM73 of Is of Is

* with time multiplier set to 1.0 and current switched to zero Short term overload (2TJM10, 60, 70 for 1.8 sec and
2TJM20, 30 for 1 sec)
5A IDMT element 2.5A to 10A 50x setting - max of 250A
4. ACCURACY REFERENCE CONDITIONS 1A to 4A 50x setting
0.5A to 2A 50x setting - max of 50A
General IEC 255 - 4 1A IDMT element 0.5A to 2A 50x setting - max of 50A
Current Settings 100% of In for O/C 0.2A to 0.8A 50x setting
40% of In for E/F 0.1A to 0.4A 50x setting
Time Multiplier 1.0
Reference Tap MI=2
Reference Multiple 10 x Is 9. BURDENS

AC Nominal Burden 2TJM range

For 2TJM60 IDMT element 3VA at current 10, 20, 70,
Reference Tap Ml=4 setting 13/73
Reference Multiple 7 x 1s 1.5VA at max. 30
current setting
2VA at current 60
5. ACCURACY setting
Highset element 1 to 2VA over all
Operating Times setting range
Operating current multiple Directional 0.5VA, current all
of plug setting % 12VA, voltage at
2 7.5 rating
5 7.5
10 7.5
20 7.5 10. OUTPUT CONTACTS

The allowable variation in operating time not expressed as less 10.1. For 2TJM10, 2TJM20, 2TJM70
than 100ms.
2 normally open self reset

6. ACCURACY GENERAL Carry continuously 5A ac or dc

Overshoot Time <80ms Make and Carry 20A ac or dc for 0.5 sec
(limit L/R = 50ms and 300V)

7. ACCURACY INFLUENCING FACTORS

10.2. For 2TJM30, 2TJM60
Temperature
Ambient range -25C to +55C I normally open self reset trip duty (specified above)
Variation over range 0.2% / C I normally open self reset auxiliary duty
0.25% / C for 2TJM60
0.4% / C for 2TJM30 Reed relay contact ratings
carry continuously 3A 110V dc or 2.5A 250V dc
At reference tap setting and 10x setting. break 0.125A 110V dc or 0.1A
250V dc @ L/R=40mS

2
 PERFORMANCE SPECIFICATION 2
The reed coil has a resistance of 0.18 ohms and an operating Insulation - IEC 255-5
range of 0.8 to 25A dc. Where this range is insufficient a voltage Between any terminal 2.0kV rms for 1 min
operated type MCAA repeat relay can be fitted. and earth
Between independent 2.0kV rms for 1 min
circuits
10.3. For 2TJM13 and 2TJM73 Across normally open 1.0kV rms for 1 min
contacts
I normally closed (2 in parallel) hand reset

Break 150A at 150V ac Vibration - IEC 255-21-1 Class 1

Relays meet these requirements for vibration response and
2 normally open hard reset vibration endurance.

Make and Carry

(limit 600V) Shock and Bump - IEC 255-21-2 Class 1
continuously 3A ac or dc Relays meet the above requirements with respect to shock and
for 3 sec 8A ac or dc bump testing for Class 1 severity.
for 1 sec 16A ac or dc
Mechanical Classification
Durability In excess of 105 operations
Break
(limit 5A and 250V)
ac inductive 300Va
dc inductive 75W @ L/R=40ms

10.4. MCAA Highset Element

2 normally open self reset

Carry continuously 10A ac or dc

Make and carry 30A ac or dc for 3 sec

10.5. Indication

Hand reset flag

11. ENVIRONMENTAL WITHSTAND

Temperature - IEC 68-2-1/2

Operating range -25C to +55C
Storage range -40C to +70C

Humidity - IEC 68-2-3

Operational test 56 days at 40C and 95% RH

Transient Overvoltage - IEC 255-5

Between all terminals and earth 5kV 1.2/50s 0.5J
or between any two independent
circuits without damage or
flashover

3
2 PERFORMANCE SPECIFICATION

Figure 1 2TJM10 IDMTL Characteristics, 50Hz

4
 PERFORMANCE SPECIFICATION 2

Figure 2 2TJM20 IDMTL Characteristics, 50Hz

5
2 PERFORMANCE SPECIFICATION

Figure 3 2TJM30 IDMTL Characteristics, 50Hz

6
 PERFORMANCE SPECIFICATION 2

Figure 4 2TJM60 IDMTL Characteristics, 50Hz

7
2 PERFORMANCE SPECIFICATION

Figure 5 2TJM70 IDMTL Characteristics, 50Hz

8
 PERFORMANCE SPECIFICATION 2

Figure 6 2TJM10 IDMTL Figure 7 2TJM20 IDMTL

Characteristics, 60Hz Characteristics, 60Hz

9
2 PERFORMANCE SPECIFICATION

Figure 8 2TJM30 IDMTL Figure 9 2TJM70 IDMTL

Characteristics, 60Hz Characteristics, 60Hz

10
 PERFORMANCE SPECIFICATION 2

Characteristic
angle

Limiting vectors of Shown in maximum

operating angle torque position

Reference voltage vector

nge
e ra
c tiv
ff e
ge
adin
e

or
L

La
ect
Vector of leading

gg
nt v

in g
setting angle

re

e ff e
Cur

c tiv e
9
9

ra n g e
Always
Limits of error
operate
Never
operate

Vector of lagging
setting angle

Figure 10 Operating Characteristic of Directional Element

Voltage coil energised at 110 Volts

Phase angle (degrees)

Figure 11 Directional Current/ Phase Angle Characteristic, 5A Relay 50Hz (2TJM12)

11
2 PERFORMANCE SPECIFICATION

Figure 12 2TJM10/70 Impedance/Current Characteristic, 1A Relay, 50Hz

Figure 13 2TJM10/70 Impedance/Current Characteristic, 5A Relay, 50Hz

12
 PERFORMANCE SPECIFICATION 2

Figure I4 2TJM20 Impedance/Current Characteristic, 1A Relay, 50Hz

Figure 15 2TJM20 Impedance/Current Characteristic, 5A Relay, 50Hz

13
2 PERFORMANCE SPECIFICATION

Figure 16 2TJM30 Impedance/Current Characteristic, 1A Relay, 50Hz

Figure 17 2TJM30 Impedance/Current Characteristic, 5A Relay, 50Hz

14
 PERFORMANCE SPECIFICATION 2

Figure 18 2TJM60 Impedance/Current Characteristic, 1A Relay, 50Hz

15
2 PERFORMANCE SPECIFICATION

Figure 19 2TJM60 Impedance/Current Characteristic, 5A Relay, 50Hz

16