Statics: Vector Mechanics For Engineers

Ninth Edition
VECTOR MECHANICS FOR ENGINEERS:
1
CHAPTER
STATICS
Ferdinand P. Beer
E. Russell Johnston, Jr.
Introduction
Lecture Notes:
J. Walt Oler
Texas Tech University
2010 The McGraw-Hill Companies, Inc. All rights reserved.

Edition
Ninth
Vector Mechanics for Engineers: Statics
Contents
What is Mechanics?
Fundamental Concepts
Fundamental Principles
Systems of Units
Method of Problem Solution
Numerical Accuracy
2010 The McGraw-Hill Companies, Inc. All rights reserved. 1-2

Edition
Ninth
What is Mechanics?
Mechanics is the science which describes and predicts
the conditions of rest or motion of bodies under the
action of forces.
Categories of Mechanics:
- Rigid bodies
- Statics
- Dynamics
- Deformable bodies
- Fluids
Mechanics is an applied science - it is not an abstract

or pure science but does not have the empiricism
found in other engineering sciences.
Mechanics is the foundation of most engineering sciences

and is an indispensable prerequisite to their study.

Edition
Ninth
Fundamental Concepts
Space - associated with the notion of the position of a point P given in
terms of three coordinates measured from a reference point or origin.
Time - definition of an event requires specification of the time and
position at which it occurred.
Mass - used to characterize and compare bodies, e.g., response to

earths gravitational attraction and resistance to changes in translational
motion.
Force - represents the action of one body on another. A force is

characterized by its point of application, magnitude, and direction, i.e.,
a force is a vector quantity.
In Newtonian Mechanics, space, time, and mass are absolute concepts,

independent of each other. Force, however, is not independent of the
other three. The force acting on a body is related to the mass of the body
and the variation of its velocity with time.
Edition
Ninth
Fundamental Principles
Newtons First Law: If the resultant force on a
particle is zero, the particle will remain at rest
or continue to move in a straight line.
Newtons Second Law: A particle will have

an acceleration proportional to a nonzero
resultant applied force.
Parallelogram Law
F ma
Newtons Third Law: The forces of action and
reaction between two particles have the same
magnitude and line of action with opposite
sense.
Newtons Law of Gravitation: Two particles

are attracted with equal and opposite forces,
Principle of Transmissibility Mm
F G 2 W mg , g
GM
r R2
Edition
Ninth
Systems of Units
International System of Units (SI):
The basic units are length, time, and
mass which are arbitrarily defined as the
Kinetic Units: length, time, mass, meter (m), second (s), and kilogram
and force. (kg). Force is the derived unit,
F ma
Three of the kinetic units, referred to m
as basic units, may be defined
1 N 1 kg 1 2
s
arbitrarily. The fourth unit, referred
to as a derived unit, must have a U.S. Customary Units:
definition compatible with Newtons The basic units are length, time, and
2nd Law, force which are arbitrarily defined as the
foot (ft), second (s), and pound (lb).
F ma Mass is the derived unit,
F
m
a
1 lb
1slug
1 ft s
Edition
Ninth
Method of Problem Solution
Problem Statement: Solution Check:
Includes given data, specification of - Test for errors in reasoning by
what is to be determined, and a figure verifying that the units of the
showing all quantities involved. computed results are correct,
- test for errors in computation by
Free-Body Diagrams: substituting given data and computed
Create separate diagrams for each of results into previously unused
the bodies involved with a clear equations based on the six principles,
indication of all forces acting on - always apply experience and physical
each body. intuition to assess whether results seem
Fundamental Principles: reasonable
The six fundamental principles are
applied to express the conditions of
rest or motion of each body. The
rules of algebra are applied to solve
the equations for the unknown
quantities.
Edition
Ninth
Numerical Accuracy
The accuracy of a solution depends on 1) accuracy of the given
data, and 2) accuracy of the computations performed. The solution
cannot be more accurate than the less accurate of these two.
The use of hand calculators and computers generally makes the

accuracy of the computations much greater than the accuracy of the
data. Hence, the solution accuracy is usually limited by the data
accuracy.
As a general rule for engineering problems, the data are seldom

known with an accuracy greater than 0.2%. Therefore, it is usually
appropriate to record parameters beginning with 1 with four digits
and with three digits in all other cases, i.e., 40.2 lb and 15.58 lb.

Statics: Vector Mechanics For Engineers

Uploaded by

Copyright:

Available Formats

Statics: Vector Mechanics For Engineers

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Statics: Vector Mechanics For Engineers

Uploaded by

Copyright:

Available Formats

Ninth Edition

VECTOR MECHANICS FOR ENGINEERS:

2010 The McGraw-Hill Companies, Inc. All rights reserved.

2010 The McGraw-Hill Companies, Inc. All rights reserved. 1-2

Mechanics is an applied science - it is not an abstract

Mechanics is the foundation of most engineering sciences

2010 The McGraw-Hill Companies, Inc. All rights reserved. 1-3

Mass - used to characterize and compare bodies, e.g., response to

Force - represents the action of one body on another. A force is

In Newtonian Mechanics, space, time, and mass are absolute concepts,

Newtons Second Law: A particle will have

Newtons Law of Gravitation: Two particles

The use of hand calculators and computers generally makes the

As a general rule for engineering problems, the data are seldom

2010 The McGraw-Hill Companies, Inc. All rights reserved. 1-8

You might also like